diff --git a/EpsilonAuxBMS/Inc/SetContactorsTask.h b/EpsilonAuxBMS/Inc/SetContactorsTask.h new file mode 100644 index 00000000..72102a86 --- /dev/null +++ b/EpsilonAuxBMS/Inc/SetContactorsTask.h @@ -0,0 +1,13 @@ +#pragma once +#include "AuxBmsTasks.h" +#include "stm32f4xx_hal.h" +#include "stm32f4xx_hal_adc.h" +#include "OrionStatus.h" + +extern ADC_HandleTypeDef hadc1; // main.c + +// Task for turning on contactors +// arg: osMutexId* auxStatusMutex +void setContactorsTask(void const* arg); + +void disconnectContactors(uint8_t isContactorError); diff --git a/EpsilonAuxBMS/Src/SetContactorsTask.c b/EpsilonAuxBMS/Src/SetContactorsTask.c new file mode 100644 index 00000000..ab88537d --- /dev/null +++ b/EpsilonAuxBMS/Src/SetContactorsTask.c @@ -0,0 +1,547 @@ +#include "SetContactorsTask.h" +/* + This task allows for the turning on of the common, charge, and discharge contactors. + It works by checking if the current through the contactors is high for any reason and keeps + doing so until the current is low. Once the current is low, it turns the common contactor on + and then waits for one second. Within that second, it is expected that the current spike through + the contactors would have come down and the contactor sense line should be low. If this isn't + the case, it tries again. However, if this is the case, it carries on by turning the charge contactor, + going through the same process, turning on the discharge contactor, going through the same process, and + finally turning on the high voltage enable line. It then enters a state of being finished. + If any of the Orion gpio lines are low, or the battery voltages that Orion are not in the expected range, + it enters a blocked state and waits for everything to return to normal. This is a just a safety measure because in reality + the whole system should shut down and there shouldn't be power for the board if anything on Orion's side goes wrong. +*/ + +static const uint32_t AUX_SET_CONTACTOR_FREQ = 1000; // Every 1 second +static const float CURRENT_SENSE_RESISTOR = 0.001; //actually 1 mOhm, but 1 Ohm for testing +static const int GAIN = 250; +static const uint32_t SENSE_SETUP_TIME = 50; // Setup time for current_sense +static const float CURRENT_LOWER_THRESHOLD = 0.25; // Lower current threshold +static const uint32_t ADC_POLL_TIMEOUT = 10; +static const int NUM_SENSES = 3; // The number of senses to take at a time when reading current amplifier +static const int MAX_SENSE_DIFF = 10; // The maximum difference between senses read from current amplifier +static const int MAX_CURRENT_READ_ATTEMPTS = 50; // The maximum number of times to try obtaining a settled CURRENT_SENSE + +typedef enum ContactorsSettingState +{ + FIRST_CHECK, + COMMON_ENABLE_CHECK, + CHARGE_ENABLE_CHECK, + DISCHARGE_ENABLE_CHECK, + DONE, + BLOCKED, + CONTACTOR_DISCONNECTED, + SHUTDOWN +} ContactorsSettingState; + +// Function for reading current through the contactors. +// The current is read from the current amplifier +uint32_t readCurrentThroughContactors(void); +// Function for checking if a specific contactor has been set +int isContactorSet(uint16_t pin, GPIO_TypeDef* port, int current_multiplier); +// Turns off all contactors and adjusts auxstatus if isContactorError is 1 +void disconnectContactors(uint8_t isContactorError); +// Resets sense array to all 0s +void resetSenseArray(uint32_t senses[]); +// Function for checking if CURRENT_SENSE is at a stable value +int isSenseStable(uint32_t senses[]); + +void setContactorsTask(void const* arg) +{ + // One time osDelayUntil initialization + uint32_t prevWakeTime = osKernelSysTick(); + + ContactorsSettingState state = FIRST_CHECK; + ContactorsSettingState prevState = state; + uint8_t hasChargeBeenSet = 0; + uint8_t hasDischargeBeenSet = 0; + + for (;;) + { + osDelayUntil(&prevWakeTime, AUX_SET_CONTACTOR_FREQ); + + if (!orionStatus.batteryVoltagesInRange && !auxStatus.startUpSequenceDone && state != CONTACTOR_DISCONNECTED) + { + state = BLOCKED; + } + + switch (state) + { + case FIRST_CHECK: + { + // Check current is low before beginning to turn on contactors + // If current is high for some reason, cycle again + uint8_t contactorError = !isContactorSet(0xFF, NULL, 1); // Don't want to read an actual sense pin + + if (osMutexWait(auxStatus.auxStatusMutex, 0) != osOK) + { + continue; + } + + auxStatus.contactorError = contactorError; + + osMutexRelease(auxStatus.auxStatusMutex); + + if (!contactorError) + { + // Turn on Common Contactor + HAL_GPIO_WritePin(COMMON_ENABLE_GPIO_Port, COMMON_ENABLE_Pin, GPIO_PIN_SET); + prevState = state; + state = COMMON_ENABLE_CHECK; + } + + break; + } + + case COMMON_ENABLE_CHECK: + { + uint8_t contactorError = !isContactorSet(COMMON_SENSE_Pin, COMMON_SENSE_GPIO_Port, 1); + + if (osMutexWait(auxStatus.auxStatusMutex, 0) != osOK) + { + continue; + } + + auxStatus.contactorError = contactorError; + + osMutexRelease(auxStatus.auxStatusMutex); + + if (!contactorError) + { + prevState = state; + state = CHARGE_ENABLE_CHECK; + HAL_GPIO_WritePin(CHARGE_ENABLE_GPIO_Port, CHARGE_ENABLE_Pin, GPIO_PIN_SET); + } + + break; + } + + case CHARGE_ENABLE_CHECK: + { + uint8_t contactorError = 0; + + const uint8_t commonSense = !HAL_GPIO_ReadPin(COMMON_SENSE_GPIO_Port, COMMON_SENSE_Pin); + const uint8_t dischargeSense = !HAL_GPIO_ReadPin(DISCHARGE_SENSE_GPIO_Port, DISCHARGE_SENSE_Pin); + const uint8_t chargeSense = !HAL_GPIO_ReadPin(CHARGE_SENSE_GPIO_Port, CHARGE_SENSE_Pin); + + if (!commonSense || (hasDischargeBeenSet && !dischargeSense && !orionStatus.dischargeContactorOverriden)) + { + disconnectContactors(1); + state = CONTACTOR_DISCONNECTED; + break; + } + + if (!chargeSense) + { + int numContactors = dischargeSense ? 3 : 2; + hasChargeBeenSet = isContactorSet(CHARGE_SENSE_Pin, CHARGE_SENSE_GPIO_Port, numContactors); + + if (!hasChargeBeenSet) // Turn back off if not set + { + HAL_GPIO_WritePin(CHARGE_ENABLE_GPIO_Port, CHARGE_ENABLE_Pin, GPIO_PIN_RESET); + } + } + + switch (prevState) + { + case COMMON_ENABLE_CHECK: + case DONE: + contactorError = !hasChargeBeenSet; + break; + + case DISCHARGE_ENABLE_CHECK: + contactorError = !(hasChargeBeenSet && hasDischargeBeenSet); + break; + + default: // Something went really wrong in the logic, stop everything + disconnectContactors(0); + state = SHUTDOWN; + continue; + } + + if (osMutexWait(auxStatus.auxStatusMutex, 0) != osOK) + { + continue; + } + + auxStatus.contactorError = contactorError; + + if (hasDischargeBeenSet && hasChargeBeenSet) + { + auxStatus.startUpSequenceDone = 1; + state = DONE; + } + + osMutexRelease(auxStatus.auxStatusMutex); + + if (!hasDischargeBeenSet) + { + HAL_GPIO_WritePin(DISCHARGE_ENABLE_GPIO_Port, DISCHARGE_ENABLE_Pin, GPIO_PIN_SET); + prevState = state; + state = DISCHARGE_ENABLE_CHECK; + } + else if (!hasChargeBeenSet) + { + prevState = state; + state = DISCHARGE_ENABLE_CHECK; + } + + break; + } + + case DISCHARGE_ENABLE_CHECK: + { + uint8_t contactorError = 0; + + const uint8_t commonSense = !HAL_GPIO_ReadPin(COMMON_SENSE_GPIO_Port, COMMON_SENSE_Pin); + const uint8_t chargeSense = !HAL_GPIO_ReadPin(CHARGE_SENSE_GPIO_Port, CHARGE_SENSE_Pin); + const uint8_t dischargeSense = !HAL_GPIO_ReadPin(DISCHARGE_SENSE_GPIO_Port, DISCHARGE_SENSE_Pin); + + if (!commonSense || (hasChargeBeenSet && !chargeSense && !orionStatus.chargeContactorOverriden)) + { + disconnectContactors(1); + state = CONTACTOR_DISCONNECTED; + break; + } + + if (!dischargeSense) + { + int numContactors = chargeSense ? 3 : 2; + hasDischargeBeenSet = isContactorSet(DISCHARGE_SENSE_Pin, DISCHARGE_SENSE_GPIO_Port, numContactors); + + if (hasDischargeBeenSet) + { + // Enable high voltage + HAL_GPIO_WritePin(HV_ENABLE_GPIO_Port, HV_ENABLE_Pin, GPIO_PIN_SET); + } + else // Turn back off if not set + { + HAL_GPIO_WritePin(DISCHARGE_ENABLE_GPIO_Port, DISCHARGE_ENABLE_Pin, GPIO_PIN_RESET); + } + } + + switch (prevState) + { + case DONE: + contactorError = !hasDischargeBeenSet; + break; + + case CHARGE_ENABLE_CHECK: + contactorError = !(hasChargeBeenSet && hasDischargeBeenSet); + break; + + default: // Something went really wrong in the logic, stop everything + disconnectContactors(0); + state = SHUTDOWN; + continue; + } + + if (osMutexWait(auxStatus.auxStatusMutex, 0) != osOK) + { + continue; + } + + auxStatus.contactorError = contactorError; + + if (hasDischargeBeenSet && hasChargeBeenSet) + { + auxStatus.startUpSequenceDone = 1; + state = DONE; + } + + osMutexRelease(auxStatus.auxStatusMutex); + + if (!hasChargeBeenSet) + { + prevState = state; + state = CHARGE_ENABLE_CHECK; + HAL_GPIO_WritePin(CHARGE_ENABLE_GPIO_Port, CHARGE_ENABLE_Pin, GPIO_PIN_SET); + } + else if (!hasDischargeBeenSet) + { + prevState = state; + state = CHARGE_ENABLE_CHECK; + } + + + + break; + } + + case DONE: + { + const uint8_t commonSense = !HAL_GPIO_ReadPin(COMMON_SENSE_GPIO_Port, COMMON_SENSE_Pin); + const uint8_t chargeSense = !HAL_GPIO_ReadPin(CHARGE_SENSE_GPIO_Port, CHARGE_SENSE_Pin); + const uint8_t dischargeSense = !HAL_GPIO_ReadPin(DISCHARGE_SENSE_GPIO_Port, DISCHARGE_SENSE_Pin); + + uint8_t isChargeTurningOn = 0; + uint8_t isDischargeTurningOn = 0; + + if (orionStatus.shutOff) + { + state = SHUTDOWN; + continue; + } + else if (!commonSense) + { + disconnectContactors(1); + state = CONTACTOR_DISCONNECTED; + } + + if (orionStatus.allowCharge && orionStatus.chargeContactorOverriden && !chargeSense) + { + if (osMutexWait(orionStatus.orionStatusMutex, 0) != osOK) + { + continue; + } + + orionStatus.chargeContactorOverriden = 0; + osMutexRelease(orionStatus.orionStatusMutex); + + isChargeTurningOn = 1; + hasChargeBeenSet = 0; + // Turn on charge Contactor + HAL_GPIO_WritePin(CHARGE_ENABLE_GPIO_Port, CHARGE_ENABLE_Pin, GPIO_PIN_SET); + prevState = state; + state = CHARGE_ENABLE_CHECK; + } + else if (orionStatus.allowDischarge && orionStatus.dischargeContactorOverriden && !dischargeSense) + { + if (osMutexWait(orionStatus.orionStatusMutex, 0) != osOK) + { + continue; + } + + orionStatus.dischargeContactorOverriden = 0; + osMutexRelease(orionStatus.orionStatusMutex); + + isDischargeTurningOn = 1; + hasDischargeBeenSet = 0; + HAL_GPIO_WritePin(DISCHARGE_ENABLE_GPIO_Port, DISCHARGE_ENABLE_Pin, GPIO_PIN_SET); + prevState = state; + state = DISCHARGE_ENABLE_CHECK; + } + + + // If charge contactor should be on, but isn't, disconnect + // or if discharge contactor should be on, but isn't, disconnect + if ((orionStatus.allowCharge && !chargeSense && !isChargeTurningOn && !orionStatus.chargeContactorOverriden) || + (orionStatus.allowDischarge && !dischargeSense && !isDischargeTurningOn && !orionStatus.dischargeContactorOverriden)) + { + disconnectContactors(1); + state = CONTACTOR_DISCONNECTED; + } + + break; + } + + case BLOCKED: + { + const uint8_t commonSense = !HAL_GPIO_ReadPin(COMMON_SENSE_GPIO_Port, COMMON_SENSE_Pin); + const uint8_t chargeSense = !HAL_GPIO_ReadPin(CHARGE_SENSE_GPIO_Port, CHARGE_SENSE_Pin); + const uint8_t dischargeSense = !HAL_GPIO_ReadPin(DISCHARGE_SENSE_GPIO_Port, DISCHARGE_SENSE_Pin); + + // If orion isn't overiding the contactors, but they are supposed to have been set, but aren't + // , this is an error condition and all contactors should be disconnected. + if (prevState > COMMON_ENABLE_CHECK + && (!commonSense || + (!orionStatus.chargeContactorOverriden && hasChargeBeenSet && !chargeSense) || + (!orionStatus.dischargeContactorOverriden && hasDischargeBeenSet && !dischargeSense))) + { + disconnectContactors(1); + state = CONTACTOR_DISCONNECTED; + } + else if (orionStatus.batteryVoltagesInRange) + { + if (orionStatus.chargeContactorOverriden) + { + hasChargeBeenSet = 0; + } + + if (orionStatus.dischargeContactorOverriden) + { + hasDischargeBeenSet = 0; + } + + if (osMutexWait(orionStatus.orionStatusMutex, 0) != osOK) + { + continue; + } + + orionStatus.chargeContactorOverriden = 0; + orionStatus.dischargeContactorOverriden = 0; + + osMutexRelease(orionStatus.orionStatusMutex); + state = FIRST_CHECK; + } + + break; + } + + case CONTACTOR_DISCONNECTED: + case SHUTDOWN: + break; + + default: + state = FIRST_CHECK; + } + } +} + +int isContactorSet(uint16_t pin, GPIO_TypeDef* port, int current_multiplier) +{ + float pwrVoltage = 0.0; + float pwrCurrent = 0.0; + uint8_t sense_pin; + // Get 12bit current analog input + uint32_t current_sense = readCurrentThroughContactors(); + + if (current_sense == 0xDEADBEEF) + { + return 0; + } + + pwrVoltage = 3.3 * current_sense / 0xFFF / GAIN; // change ADC value into the voltage read + pwrCurrent = pwrVoltage / CURRENT_SENSE_RESISTOR; // convert voltage to current + + if (pin == 0xFF && port == NULL) + { + sense_pin = 1; + } + else + { + sense_pin = !HAL_GPIO_ReadPin(port, pin); + } + + // If current is high for some reason or sense pin is high something is wrong + if (pwrCurrent > CURRENT_LOWER_THRESHOLD * current_multiplier || !sense_pin) + { + return 0; + } + + return 1; +} + +/* + This function takes multiple reads because the current amplifier has a bit of a setup time + to make sure that erroneous values aren't read, multiple reads are taken till we have a + relatively steady value. +*/ +uint32_t readCurrentThroughContactors(void) +{ + // Enable current amplifier. Allow time to settle and take multiple valid concurrent readings + // to make sure it isn't changing + HAL_GPIO_WritePin(CURRENT_SENSE_ENABLE_GPIO_Port, CURRENT_SENSE_ENABLE_Pin, GPIO_PIN_SET); + uint32_t senses[NUM_SENSES]; + uint32_t returnValue = 0xDEADBEEF; + int count = 0; + + // Want to limit it so we don't get an infinite loop + while (count < MAX_CURRENT_READ_ATTEMPTS) + { + resetSenseArray(senses); + osDelay(SENSE_SETUP_TIME); + int senseStable = isSenseStable(senses); + + if (senseStable == 1) + { + HAL_GPIO_WritePin(CURRENT_SENSE_ENABLE_GPIO_Port, CURRENT_SENSE_ENABLE_Pin, GPIO_PIN_RESET); + returnValue = senses[0]; + break; + } + else if (senseStable == -1) + { + HAL_GPIO_WritePin(CURRENT_SENSE_ENABLE_GPIO_Port, CURRENT_SENSE_ENABLE_Pin, GPIO_PIN_RESET); + break; + } + + count++; + } + + HAL_GPIO_WritePin(CURRENT_SENSE_ENABLE_GPIO_Port, CURRENT_SENSE_ENABLE_Pin, GPIO_PIN_RESET); + return returnValue; +} + +/* + Multiple reads are taken and buffered into an array. The maximum and minimum value read are + found. Since these values will have the greatest difference, their difference must be less than + or equal to the allowable difference. If it is, the CURRENT_SENSE is stable, otherwise, it is deemed + not stable +*/ +int isSenseStable(uint32_t senses[]) +{ + for (int counter = 0; counter < NUM_SENSES; counter++) + { + for (int i = NUM_SENSES - 1; i > 0; i--) + { + senses[i] = senses[i - 1]; + } + + if (HAL_ADC_PollForConversion(&hadc1, ADC_POLL_TIMEOUT) == HAL_OK) + { + senses[0] = HAL_ADC_GetValue(&hadc1); + } + else + { + return -1; + } + } + + uint32_t max = senses[0]; + uint32_t min = senses[0]; + + for (int i = 1; i < NUM_SENSES; i++) + { + if (senses[i] > max) + { + max = senses[i]; + } + + if (senses[i] < min) + { + min = senses[i]; + } + } + + if (max - min > MAX_SENSE_DIFF) + { + return 0; + } + else + { + return 1; + } +} + +void resetSenseArray(uint32_t senses[]) +{ + for (int i = 0; i < NUM_SENSES; i++) + { + senses[i] = 0; + } +} + +void disconnectContactors(uint8_t isContactorError) +{ + // Turn all contactors and high voltage enable off + HAL_GPIO_WritePin(HV_ENABLE_GPIO_Port, HV_ENABLE_Pin, GPIO_PIN_RESET); + HAL_GPIO_WritePin(DISCHARGE_ENABLE_GPIO_Port, DISCHARGE_ENABLE_Pin, GPIO_PIN_RESET); + HAL_GPIO_WritePin(CHARGE_ENABLE_GPIO_Port, CHARGE_ENABLE_Pin, GPIO_PIN_RESET); + HAL_GPIO_WritePin(COMMON_ENABLE_GPIO_Port, COMMON_ENABLE_Pin, GPIO_PIN_RESET); + + if (isContactorError) + { + while (osMutexWait(auxStatus.auxStatusMutex, 0) != osOK) // Not sure if this is the best idea + // but will guarantee that we return to this spot + { + osDelay(10); + } + + auxStatus.contactorError = 1; + auxStatus.strobeBmsLight = 1; + auxStatus.allowCharge = 0; + + osMutexRelease(auxStatus.auxStatusMutex); + } +} diff --git a/EpsilonAuxBMS/Tests/mocks/MockSetContactorsTask.c b/EpsilonAuxBMS/Tests/mocks/MockSetContactorsTask.c new file mode 100644 index 00000000..1db1a7ba --- /dev/null +++ b/EpsilonAuxBMS/Tests/mocks/MockSetContactorsTask.c @@ -0,0 +1,138 @@ +/* AUTOGENERATED FILE. DO NOT EDIT. */ +#include +#include +#include +#include "cmock.h" +#include "MockSetContactorsTask.h" + +static const char* CMockString_arg = "arg"; +static const char* CMockString_disconnectContactors = "disconnectContactors"; +static const char* CMockString_isContactorError = "isContactorError"; +static const char* CMockString_setContactorsTask = "setContactorsTask"; + +typedef struct _CMOCK_setContactorsTask_CALL_INSTANCE +{ + UNITY_LINE_TYPE LineNumber; + void const* Expected_arg; + +} CMOCK_setContactorsTask_CALL_INSTANCE; + +typedef struct _CMOCK_disconnectContactors_CALL_INSTANCE +{ + UNITY_LINE_TYPE LineNumber; + uint8_t Expected_isContactorError; + +} CMOCK_disconnectContactors_CALL_INSTANCE; + +static struct MockSetContactorsTaskInstance +{ + CMOCK_MEM_INDEX_TYPE setContactorsTask_CallInstance; + CMOCK_MEM_INDEX_TYPE disconnectContactors_CallInstance; +} Mock; + +extern jmp_buf AbortFrame; + +void MockSetContactorsTask_Verify(void) +{ + UNITY_LINE_TYPE cmock_line = TEST_LINE_NUM; + CMOCK_MEM_INDEX_TYPE call_instance; + call_instance = Mock.setContactorsTask_CallInstance; + + if (CMOCK_GUTS_NONE != call_instance) + { + UNITY_SET_DETAIL(CMockString_setContactorsTask); + UNITY_TEST_FAIL(cmock_line, CMockStringCalledLess); + } + + call_instance = Mock.disconnectContactors_CallInstance; + + if (CMOCK_GUTS_NONE != call_instance) + { + UNITY_SET_DETAIL(CMockString_disconnectContactors); + UNITY_TEST_FAIL(cmock_line, CMockStringCalledLess); + } +} + +void MockSetContactorsTask_Init(void) +{ + MockSetContactorsTask_Destroy(); +} + +void MockSetContactorsTask_Destroy(void) +{ + CMock_Guts_MemFreeAll(); + memset(&Mock, 0, sizeof(Mock)); +} + +void setContactorsTask(void const* arg) +{ + UNITY_LINE_TYPE cmock_line = TEST_LINE_NUM; + CMOCK_setContactorsTask_CALL_INSTANCE* cmock_call_instance; + UNITY_SET_DETAIL(CMockString_setContactorsTask); + cmock_call_instance = (CMOCK_setContactorsTask_CALL_INSTANCE*)CMock_Guts_GetAddressFor(Mock.setContactorsTask_CallInstance); + Mock.setContactorsTask_CallInstance = CMock_Guts_MemNext(Mock.setContactorsTask_CallInstance); + UNITY_TEST_ASSERT_NOT_NULL(cmock_call_instance, cmock_line, CMockStringCalledMore); + cmock_line = cmock_call_instance->LineNumber; + { + UNITY_SET_DETAILS(CMockString_setContactorsTask, CMockString_arg); + + if (cmock_call_instance->Expected_arg == NULL) + { + UNITY_TEST_ASSERT_NULL(arg, cmock_line, CMockStringExpNULL); + } + else + { + UNITY_TEST_ASSERT_EQUAL_HEX8_ARRAY(cmock_call_instance->Expected_arg, arg, 1, cmock_line, CMockStringMismatch); + } + } + UNITY_CLR_DETAILS(); +} + +void CMockExpectParameters_setContactorsTask(CMOCK_setContactorsTask_CALL_INSTANCE* cmock_call_instance, void const* arg) +{ + cmock_call_instance->Expected_arg = arg; +} + +void setContactorsTask_CMockExpect(UNITY_LINE_TYPE cmock_line, void const* arg) +{ + CMOCK_MEM_INDEX_TYPE cmock_guts_index = CMock_Guts_MemNew(sizeof(CMOCK_setContactorsTask_CALL_INSTANCE)); + CMOCK_setContactorsTask_CALL_INSTANCE* cmock_call_instance = (CMOCK_setContactorsTask_CALL_INSTANCE*)CMock_Guts_GetAddressFor(cmock_guts_index); + UNITY_TEST_ASSERT_NOT_NULL(cmock_call_instance, cmock_line, CMockStringOutOfMemory); + memset(cmock_call_instance, 0, sizeof(*cmock_call_instance)); + Mock.setContactorsTask_CallInstance = CMock_Guts_MemChain(Mock.setContactorsTask_CallInstance, cmock_guts_index); + cmock_call_instance->LineNumber = cmock_line; + CMockExpectParameters_setContactorsTask(cmock_call_instance, arg); +} + +void disconnectContactors(uint8_t isContactorError) +{ + UNITY_LINE_TYPE cmock_line = TEST_LINE_NUM; + CMOCK_disconnectContactors_CALL_INSTANCE* cmock_call_instance; + UNITY_SET_DETAIL(CMockString_disconnectContactors); + cmock_call_instance = (CMOCK_disconnectContactors_CALL_INSTANCE*)CMock_Guts_GetAddressFor(Mock.disconnectContactors_CallInstance); + Mock.disconnectContactors_CallInstance = CMock_Guts_MemNext(Mock.disconnectContactors_CallInstance); + UNITY_TEST_ASSERT_NOT_NULL(cmock_call_instance, cmock_line, CMockStringCalledMore); + cmock_line = cmock_call_instance->LineNumber; + { + UNITY_SET_DETAILS(CMockString_disconnectContactors, CMockString_isContactorError); + UNITY_TEST_ASSERT_EQUAL_HEX8(cmock_call_instance->Expected_isContactorError, isContactorError, cmock_line, CMockStringMismatch); + } + UNITY_CLR_DETAILS(); +} + +void CMockExpectParameters_disconnectContactors(CMOCK_disconnectContactors_CALL_INSTANCE* cmock_call_instance, uint8_t isContactorError) +{ + cmock_call_instance->Expected_isContactorError = isContactorError; +} + +void disconnectContactors_CMockExpect(UNITY_LINE_TYPE cmock_line, uint8_t isContactorError) +{ + CMOCK_MEM_INDEX_TYPE cmock_guts_index = CMock_Guts_MemNew(sizeof(CMOCK_disconnectContactors_CALL_INSTANCE)); + CMOCK_disconnectContactors_CALL_INSTANCE* cmock_call_instance = (CMOCK_disconnectContactors_CALL_INSTANCE*)CMock_Guts_GetAddressFor(cmock_guts_index); + UNITY_TEST_ASSERT_NOT_NULL(cmock_call_instance, cmock_line, CMockStringOutOfMemory); + memset(cmock_call_instance, 0, sizeof(*cmock_call_instance)); + Mock.disconnectContactors_CallInstance = CMock_Guts_MemChain(Mock.disconnectContactors_CallInstance, cmock_guts_index); + cmock_call_instance->LineNumber = cmock_line; + CMockExpectParameters_disconnectContactors(cmock_call_instance, isContactorError); +} + diff --git a/EpsilonAuxBMS/Tests/mocks/MockSetContactorsTask.h b/EpsilonAuxBMS/Tests/mocks/MockSetContactorsTask.h new file mode 100644 index 00000000..aeaf4ca2 --- /dev/null +++ b/EpsilonAuxBMS/Tests/mocks/MockSetContactorsTask.h @@ -0,0 +1,38 @@ +/* AUTOGENERATED FILE. DO NOT EDIT. */ +#ifndef _MOCKSETCONTACTORSTASK_H +#define _MOCKSETCONTACTORSTASK_H + +#include "unity.h" +#include "SetContactorsTask.h" + +/* Ignore the following warnings, since we are copying code */ +#if defined(__GNUC__) && !defined(__ICC) && !defined(__TMS470__) +#if __GNUC__ > 4 || (__GNUC__ == 4 && (__GNUC_MINOR__ > 6 || (__GNUC_MINOR__ == 6 && __GNUC_PATCHLEVEL__ > 0))) +#pragma GCC diagnostic push +#endif +#if !defined(__clang__) +#pragma GCC diagnostic ignored "-Wpragmas" +#endif +#pragma GCC diagnostic ignored "-Wunknown-pragmas" +#pragma GCC diagnostic ignored "-Wduplicate-decl-specifier" +#endif + +void MockSetContactorsTask_Init(void); +void MockSetContactorsTask_Destroy(void); +void MockSetContactorsTask_Verify(void); + + + + +#define setContactorsTask_Expect(arg) setContactorsTask_CMockExpect(__LINE__, arg) +void setContactorsTask_CMockExpect(UNITY_LINE_TYPE cmock_line, void const* arg); +#define disconnectContactors_Expect(isContactorError) disconnectContactors_CMockExpect(__LINE__, isContactorError) +void disconnectContactors_CMockExpect(UNITY_LINE_TYPE cmock_line, uint8_t isContactorError); + +#if defined(__GNUC__) && !defined(__ICC) && !defined(__TMS470__) +#if __GNUC__ > 4 || (__GNUC__ == 4 && (__GNUC_MINOR__ > 6 || (__GNUC_MINOR__ == 6 && __GNUC_PATCHLEVEL__ > 0))) +#pragma GCC diagnostic pop +#endif +#endif + +#endif diff --git a/EpsilonAuxBMS/Tests/tests/SetContactorsTaskTest/Makefile b/EpsilonAuxBMS/Tests/tests/SetContactorsTaskTest/Makefile new file mode 100644 index 00000000..cca3563f --- /dev/null +++ b/EpsilonAuxBMS/Tests/tests/SetContactorsTaskTest/Makefile @@ -0,0 +1,133 @@ +TARGET = SetContactorsTaskTest +EMBEDDED_REPO_ROOT = ../../../../ + +UNITY_DIR = $(EMBEDDED_REPO_ROOT)/UnityTestingTool/ +UNITY_SRC_DIR = $(UNITY_DIR)/src +CMOCK_DIR = $(UNITY_DIR)/CMock/src + +AUX_BMS_DIR = $(EMBEDDED_REPO_ROOT)/EpsilonAuxBMS/ +AUX_BMS_TESTS_DIR = $(AUX_BMS_DIR)/Tests +HELPER_DIR = $(AUX_BMS_TESTS_DIR) +AUX_BMS_SRC_DIR = $(AUX_BMS_DIR)/Src/ +AUX_BMS_INC_DIR = $(AUX_BMS_DIR)/Inc/ + +MIDDLEWARES_DIR = $(AUX_BMS_DIR)/Middlewares/ +DRIVERS_PATH = $(AUX_BMS_DIR)/Drivers/ +MOCK_DIR = $(AUX_BMS_TESTS_DIR)/mocks/ + +ifeq ($(OS),Windows_NT) + ifeq ($(shell uname -s),) # not in a bash-like shell + CLEANUP = del /F /Q + MKDIR = mkdir + else # in a bash-like shell, like msys + CLEANUP = rm -rf + MKDIR = mkdir -p + endif + TARGET_EXTENSION=.exe +else + CLEANUP = rm -rf + MKDIR = mkdir -p + TARGET_EXTENSION=out +endif + +.PHONY: clean +.PHONY: test +.PHONY: all + +PATHS = -I . \ +-I $(MOCK_DIR) \ +-I ${AUX_BMS_TESTS_DIR} \ +-I $(AUX_BMS_INC_DIR) \ +-I $(UNITY_SRC_DIR) \ +-I $(CMOCK_DIR) \ +-I $(MIDDLEWARES_DIR)/Third_Party/FreeRTOS/Source/CMSIS_RTOS \ +-I $(MIDDLEWARES_DIR)/Third_Party/FreeRTOS/Source/include \ +-I $(MIDDLEWARES_DIR)/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F \ +-I $(DRIVERS_PATH)/STM32F4xx_HAL_Driver/Inc/ \ +-I $(DRIVERS_PATH)/CMSIS/Device/ST/STM32F4xx/Include/ \ +-I $(DRIVERS_PATH)/CMSIS/Include + +PATHT = ./ +PATHB = build/ +PATHD = build/depends/ +PATHO = build/objs/ +PATHR = build/results/ + +SRCT = $(wildcard $(PATHT)*.c) + +COMPILE=gcc +CFLAGS=-I$(UNITY_SRC_DIR) $(PATHS) -DSTM32F407xx + +AUX_BMS_SOURCES = \ + $(AUX_BMS_SRC_DIR)SetContactorsTask.c \ + +TEST_SOURCES = \ + main.c \ + SetContactorsTaskTest.c \ + +HELPER_SOURCES = \ + $(AUX_BMS_TESTS_DIR)/OrionStatusHelper.c \ + $(AUX_BMS_TESTS_DIR)/AuxStatusHelper.c \ + +UNITY_SOURCES = $(UNITY_SRC_DIR)unity.c +CMOCK_SOURCES = $(CMOCK_DIR)cmock.c +MOCK_SOURCES = \ + $(MOCK_DIR)Mockstm32f4xx_hal_gpio.c \ + $(MOCK_DIR)Mockcmsis_os.c \ + $(MOCK_DIR)Mockstm32f4xx_hal_adc.c \ + $(MOCK_DIR)Mockstm32f4xx_hal_can.c \ + +# Get object file name of each source +# Each object file will be compiled as a target +AUX_BMS_OBJ = $(patsubst $(AUX_BMS_SRC_DIR)%.c, $(PATHO)%.o, $(AUX_BMS_SOURCES)) +TEST_OBJ = $(patsubst %.c, $(PATHO)%.o, $(TEST_SOURCES)) +UNITY_OBJ = $(patsubst $(UNITY_SRC_DIR)%.c, $(PATHO)%.o, $(UNITY_SOURCES)) +CMOCK_OBJ = $(patsubst $(CMOCK_DIR)%.c, $(PATHO)%.o, $(CMOCK_SOURCES)) +MOCK_OBJ = $(patsubst $(MOCK_DIR)%.c, $(PATHO)%.o, $(MOCK_SOURCES)) +HELPER_OBJ = $(patsubst $(HELPER_DIR)%.c, $(PATHO)%.o, $(HELPER_SOURCES)) + +default: mkdirs $(TARGET) + +# Parse files within this folder +$(PATHO)%.o: %.c + $(COMPILE) -c -o $@ $< $(CFLAGS) + +# Parse the unity sources +$(PATHO)%.o: $(UNITY_SRC_DIR)/%.c + $(COMPILE) -c -o $@ $< $(CFLAGS) + +# Parse files within the AuxBMS source +$(PATHO)%.o: $(AUX_BMS_SRC_DIR)/%.c + $(COMPILE) -c -o $@ $< $(CFLAGS) + +# Parse files within the cmock source +$(PATHO)%.o: $(CMOCK_DIR)/%.c + $(COMPILE) -c -o $@ $< $(CFLAGS) + +# Parse files within the mock source +$(PATHO)%.o: $(MOCK_DIR)/%.c + $(COMPILE) -c -o $@ $< $(CFLAGS) + +# Parse files within the helpers source +$(PATHO)%.o: $(HELPER_DIR)/%.c + $(COMPILE) -c -o $@ $< $(CFLAGS) + +$(TARGET): $(TEST_OBJ) $(UNITY_OBJ) $(AUX_BMS_OBJ) $(MOCK_OBJ) $(CMOCK_OBJ) $(HELPER_OBJ) + $(COMPILE) -o $(PATHB)$@ $^ $(CFLAGS) + +# Make build directories +mkdirs: + $(MKDIR) $(PATHB) + $(MKDIR) $(PATHO) + +clean: + $(CLEANUP) $(PATHB) + +test: + $(PATHB)/$(TARGET) + +.PRECIOUS: $(PATHB)Test%.$(TARGET_EXTENSION) +.PRECIOUS: $(PATHD)%.d +.PRECIOUS: $(PATHO)%.o +.PRECIOUS: $(PATHR)%.txt +.PRECIOUS: $(PATHB)$(TARGET) diff --git a/EpsilonAuxBMS/Tests/tests/SetContactorsTaskTest/SetContactorsTaskTest.c b/EpsilonAuxBMS/Tests/tests/SetContactorsTaskTest/SetContactorsTaskTest.c new file mode 100644 index 00000000..415919fa --- /dev/null +++ b/EpsilonAuxBMS/Tests/tests/SetContactorsTaskTest/SetContactorsTaskTest.c @@ -0,0 +1,24 @@ +#include "SetContactorsTaskTest.h" + +#include "unity.h" + +#include "Mockstm32f4xx_hal_gpio.h" +#include "Mockcmsis_os.h" +#include "SetContactorsTask.h" + + +void runSetContactorsTests() +{ + RUN_TEST(test_disconnectContactors); +} + +void test_disconnectContactors() +{ + HAL_GPIO_WritePin_Expect(HV_ENABLE_GPIO_Port, HV_ENABLE_Pin, GPIO_PIN_RESET); + HAL_GPIO_WritePin_Expect(DISCHARGE_ENABLE_GPIO_Port, DISCHARGE_ENABLE_Pin, GPIO_PIN_RESET); + HAL_GPIO_WritePin_Expect(CHARGE_ENABLE_GPIO_Port, CHARGE_ENABLE_Pin, GPIO_PIN_RESET); + HAL_GPIO_WritePin_Expect(COMMON_ENABLE_GPIO_Port, COMMON_ENABLE_Pin, GPIO_PIN_RESET); + osMutexWait_ExpectAndReturn(auxStatus.auxStatusMutex, 0, osOK); + osMutexRelease_ExpectAndReturn(auxStatus.auxStatusMutex, osOK); + disconnectContactors(1); +} \ No newline at end of file diff --git a/EpsilonAuxBMS/Tests/tests/SetContactorsTaskTest/SetContactorsTaskTest.h b/EpsilonAuxBMS/Tests/tests/SetContactorsTaskTest/SetContactorsTaskTest.h new file mode 100644 index 00000000..0f21f2bd --- /dev/null +++ b/EpsilonAuxBMS/Tests/tests/SetContactorsTaskTest/SetContactorsTaskTest.h @@ -0,0 +1,4 @@ +#pragma once + +void runSetContactorsTests(); +void test_disconnectContactors(); \ No newline at end of file diff --git a/EpsilonAuxBMS/Tests/tests/SetContactorsTaskTest/main.c b/EpsilonAuxBMS/Tests/tests/SetContactorsTaskTest/main.c new file mode 100644 index 00000000..7797f427 --- /dev/null +++ b/EpsilonAuxBMS/Tests/tests/SetContactorsTaskTest/main.c @@ -0,0 +1,30 @@ +//Include all files required for your functions to run +#include + +//Include required .h file for unity +#include "unity.h" +#include "stm32f4xx_hal.h" + +#include "AuxStatus.h" +#include "OrionStatusHelper.h" +#include "SetContactorsTaskTest.h" + +AuxStatus auxStatus; +ADC_HandleTypeDef hadc1; + +void setUp(void) +{ +} + +void tearDown(void) +{ +} + +int main (void) +{ + UNITY_BEGIN(); + + runSetContactorsTests(); + + return UNITY_END(); +} \ No newline at end of file diff --git a/EpsilonLights/.cproject b/EpsilonLights/.cproject deleted file mode 100644 index 31bd339c..00000000 --- a/EpsilonLights/.cproject +++ /dev/null @@ -1,94 +0,0 @@ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - diff --git a/EpsilonLights/.project b/EpsilonLights/.project deleted file mode 100644 index 08af9d64..00000000 --- a/EpsilonLights/.project +++ /dev/null @@ -1,34 +0,0 @@ - - - EpsilonLights - - - - - - org.eclipse.cdt.managedbuilder.core.genmakebuilder - clean,full,incremental, - - - - - org.eclipse.cdt.managedbuilder.core.ScannerConfigBuilder - full,incremental, - - - - - - org.eclipse.cdt.core.cnature - org.eclipse.cdt.managedbuilder.core.managedBuildNature - org.eclipse.cdt.managedbuilder.core.ScannerConfigNature - fr.ac6.mcu.ide.core.MCUProjectNature - - - - - - - - - diff --git a/EpsilonLights/Core/Inc/FreeRTOSConfig.h b/EpsilonLights/Core/Inc/FreeRTOSConfig.h new file mode 100644 index 00000000..37bb1d65 --- /dev/null +++ b/EpsilonLights/Core/Inc/FreeRTOSConfig.h @@ -0,0 +1,129 @@ +/* USER CODE BEGIN Header */ +/* + * FreeRTOS Kernel V10.0.1 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ +/* USER CODE END Header */ + +#ifndef FREERTOS_CONFIG_H +#define FREERTOS_CONFIG_H + +/*----------------------------------------------------------- + * Application specific definitions. + * + * These definitions should be adjusted for your particular hardware and + * application requirements. + * + * These parameters and more are described within the 'configuration' section of the + * FreeRTOS API documentation available on the FreeRTOS.org web site. + * + * See http://www.freertos.org/a00110.html + *----------------------------------------------------------*/ + +/* USER CODE BEGIN Includes */ +/* Section where include file can be added */ +/* USER CODE END Includes */ + +/* Ensure definitions are only used by the compiler, and not by the assembler. */ +#if defined(__ICCARM__) || defined(__CC_ARM) || defined(__GNUC__) +#include +extern uint32_t SystemCoreClock; +#endif +#define configUSE_PREEMPTION 0 +#define configSUPPORT_STATIC_ALLOCATION 0 +#define configSUPPORT_DYNAMIC_ALLOCATION 1 +#define configUSE_IDLE_HOOK 0 +#define configUSE_TICK_HOOK 0 +#define configCPU_CLOCK_HZ ( SystemCoreClock ) +#define configTICK_RATE_HZ ((TickType_t)1000) +#define configMAX_PRIORITIES ( 7 ) +#define configMINIMAL_STACK_SIZE ((uint16_t)128) +#define configTOTAL_HEAP_SIZE ((size_t)3072) +#define configMAX_TASK_NAME_LEN ( 16 ) +#define configUSE_16_BIT_TICKS 0 +#define configUSE_MUTEXES 1 +#define configQUEUE_REGISTRY_SIZE 8 +#define configUSE_PORT_OPTIMISED_TASK_SELECTION 1 + +/* Co-routine definitions. */ +#define configUSE_CO_ROUTINES 0 +#define configMAX_CO_ROUTINE_PRIORITIES ( 2 ) + +/* Set the following definitions to 1 to include the API function, or zero +to exclude the API function. */ +#define INCLUDE_vTaskPrioritySet 1 +#define INCLUDE_uxTaskPriorityGet 1 +#define INCLUDE_vTaskDelete 1 +#define INCLUDE_vTaskCleanUpResources 0 +#define INCLUDE_vTaskSuspend 1 +#define INCLUDE_vTaskDelayUntil 1 +#define INCLUDE_vTaskDelay 1 +#define INCLUDE_xTaskGetSchedulerState 1 + +/* Cortex-M specific definitions. */ +#ifdef __NVIC_PRIO_BITS +/* __BVIC_PRIO_BITS will be specified when CMSIS is being used. */ +#define configPRIO_BITS __NVIC_PRIO_BITS +#else +#define configPRIO_BITS 4 +#endif + +/* The lowest interrupt priority that can be used in a call to a "set priority" +function. */ +#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY 15 + +/* The highest interrupt priority that can be used by any interrupt service +routine that makes calls to interrupt safe FreeRTOS API functions. DO NOT CALL +INTERRUPT SAFE FREERTOS API FUNCTIONS FROM ANY INTERRUPT THAT HAS A HIGHER +PRIORITY THAN THIS! (higher priorities are lower numeric values. */ +#define configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY 5 + +/* Interrupt priorities used by the kernel port layer itself. These are generic +to all Cortex-M ports, and do not rely on any particular library functions. */ +#define configKERNEL_INTERRUPT_PRIORITY ( configLIBRARY_LOWEST_INTERRUPT_PRIORITY << (8 - configPRIO_BITS) ) +/* !!!! configMAX_SYSCALL_INTERRUPT_PRIORITY must not be set to zero !!!! +See http://www.FreeRTOS.org/RTOS-Cortex-M3-M4.html. */ +#define configMAX_SYSCALL_INTERRUPT_PRIORITY ( configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY << (8 - configPRIO_BITS) ) + +/* Normal assert() semantics without relying on the provision of an assert.h +header file. */ +/* USER CODE BEGIN 1 */ +#define configASSERT( x ) if ((x) == 0) {taskDISABLE_INTERRUPTS(); for( ;; );} +/* USER CODE END 1 */ + +/* Definitions that map the FreeRTOS port interrupt handlers to their CMSIS +standard names. */ +#define vPortSVCHandler SVC_Handler +#define xPortPendSVHandler PendSV_Handler + +/* IMPORTANT: This define is commented when used with STM32Cube firmware, when the timebase source is SysTick, + to prevent overwriting SysTick_Handler defined within STM32Cube HAL */ +#define xPortSysTickHandler SysTick_Handler + +/* USER CODE BEGIN Defines */ +/* Section where parameter definitions can be added (for instance, to override default ones in FreeRTOS.h) */ +/* USER CODE END Defines */ + +#endif /* FREERTOS_CONFIG_H */ diff --git a/EpsilonLights/Inc/Lights.h b/EpsilonLights/Core/Inc/Lights.h similarity index 90% rename from EpsilonLights/Inc/Lights.h rename to EpsilonLights/Core/Inc/Lights.h index 7e887e64..c1866172 100644 --- a/EpsilonLights/Inc/Lights.h +++ b/EpsilonLights/Core/Inc/Lights.h @@ -2,10 +2,11 @@ #include -#include "stm32f4xx.h" -#include "stm32f4xx_hal_conf.h" -#include "stm32f4xx_hal_gpio.h" -#include "stm32f4xx_hal_can.h" +#include "stm32f1xx.h" +#include "stm32f1xx_hal_conf.h" +#include "stm32f1xx_hal_gpio.h" +#include "stm32f1xx_hal_can.h" +#include "main.h" // Refer to https://docs.google.com/spreadsheets/d/1soVLjeD9Sl7z7Z6cYMyn1fmn-cG7tx_pfFDsvgkCqMU/edit?usp=sharing #define LIGHTS_UPDATE_FREQ 10 // Every 10ms @@ -55,12 +56,13 @@ typedef struct SigLightsHandle uint8_t right; } SigLightsHandle; -extern CAN_HandleTypeDef hcan2; // main.c +extern CAN_HandleTypeDef hcan; // main.c extern uint8_t lightsInputs; extern uint8_t auxBmsInputs[2]; extern uint8_t batteryErrors[5]; extern uint8_t driversInputs[4]; extern SigLightsHandle sigLightsHandle; +extern CAN_TxHeaderTypeDef canTxHdr; // Task for updating GPIOs // arg : NULL diff --git a/EpsilonLights/Core/Inc/main.h b/EpsilonLights/Core/Inc/main.h new file mode 100644 index 00000000..ced4a751 --- /dev/null +++ b/EpsilonLights/Core/Inc/main.h @@ -0,0 +1,99 @@ +/* USER CODE BEGIN Header */ +/** + ****************************************************************************** + * @file : main.h + * @brief : Header for main.c file. + * This file contains the common defines of the application. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2020 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under Ultimate Liberty license + * SLA0044, the "License"; You may not use this file except in compliance with + * the License. You may obtain a copy of the License at: + * www.st.com/SLA0044 + * + ****************************************************************************** + */ +/* USER CODE END Header */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __MAIN_H +#define __MAIN_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal.h" + +/* Private includes ----------------------------------------------------------*/ +/* USER CODE BEGIN Includes */ + +/* USER CODE END Includes */ + +/* Exported types ------------------------------------------------------------*/ +/* USER CODE BEGIN ET */ + +/* USER CODE END ET */ + +/* Exported constants --------------------------------------------------------*/ +/* USER CODE BEGIN EC */ + +/* USER CODE END EC */ + +/* Exported macro ------------------------------------------------------------*/ +/* USER CODE BEGIN EM */ + +/* USER CODE END EM */ + +/* Exported functions prototypes ---------------------------------------------*/ +void Error_Handler(void); + +/* USER CODE BEGIN EFP */ + +/* USER CODE END EFP */ + +/* Private defines -----------------------------------------------------------*/ +#define CLK_IN_Pin GPIO_PIN_0 +#define CLK_IN_GPIO_Port GPIOD +#define CLK_OUT_Pin GPIO_PIN_1 +#define CLK_OUT_GPIO_Port GPIOD +#define LED_RED_Pin GPIO_PIN_5 +#define LED_RED_GPIO_Port GPIOA +#define LED_GREEN_Pin GPIO_PIN_6 +#define LED_GREEN_GPIO_Port GPIOA +#define LED_BLUE_Pin GPIO_PIN_7 +#define LED_BLUE_GPIO_Port GPIOA +#define RSIGNAL_Pin GPIO_PIN_10 +#define RSIGNAL_GPIO_Port GPIOB +#define LSIGNAL_Pin GPIO_PIN_11 +#define LSIGNAL_GPIO_Port GPIOB +#define BRAKE_Pin GPIO_PIN_12 +#define BRAKE_GPIO_Port GPIOB +#define HEAD_Pin GPIO_PIN_13 +#define HEAD_GPIO_Port GPIOB +#define STROBE_Pin GPIO_PIN_14 +#define STROBE_GPIO_Port GPIOB +#define SWDIO_Pin GPIO_PIN_13 +#define SWDIO_GPIO_Port GPIOA +#define SWCLK_Pin GPIO_PIN_14 +#define SWCLK_GPIO_Port GPIOA +#define JTDI_Pin GPIO_PIN_15 +#define JTDI_GPIO_Port GPIOA +#define SWO_Pin GPIO_PIN_3 +#define SWO_GPIO_Port GPIOB +/* USER CODE BEGIN Private defines */ + +/* USER CODE END Private defines */ + +#ifdef __cplusplus +} +#endif + +#endif /* __MAIN_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Core/Inc/stm32f1xx_hal_conf.h b/EpsilonLights/Core/Inc/stm32f1xx_hal_conf.h new file mode 100644 index 00000000..da91a2ed --- /dev/null +++ b/EpsilonLights/Core/Inc/stm32f1xx_hal_conf.h @@ -0,0 +1,392 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_conf.h + * @brief HAL configuration file. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2017 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F1xx_HAL_CONF_H +#define __STM32F1xx_HAL_CONF_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ + +#define HAL_MODULE_ENABLED +/*#define HAL_ADC_MODULE_ENABLED */ +/*#define HAL_CRYP_MODULE_ENABLED */ +#define HAL_CAN_MODULE_ENABLED +/*#define HAL_CAN_LEGACY_MODULE_ENABLED */ +/*#define HAL_CEC_MODULE_ENABLED */ +/*#define HAL_CORTEX_MODULE_ENABLED */ +/*#define HAL_CRC_MODULE_ENABLED */ +/*#define HAL_DAC_MODULE_ENABLED */ +/*#define HAL_DMA_MODULE_ENABLED */ +/*#define HAL_ETH_MODULE_ENABLED */ +/*#define HAL_FLASH_MODULE_ENABLED */ +#define HAL_GPIO_MODULE_ENABLED +/*#define HAL_I2C_MODULE_ENABLED */ +/*#define HAL_I2S_MODULE_ENABLED */ +/*#define HAL_IRDA_MODULE_ENABLED */ +/*#define HAL_IWDG_MODULE_ENABLED */ +/*#define HAL_NOR_MODULE_ENABLED */ +/*#define HAL_NAND_MODULE_ENABLED */ +/*#define HAL_PCCARD_MODULE_ENABLED */ +/*#define HAL_PCD_MODULE_ENABLED */ +/*#define HAL_HCD_MODULE_ENABLED */ +/*#define HAL_PWR_MODULE_ENABLED */ +/*#define HAL_RCC_MODULE_ENABLED */ +/*#define HAL_RTC_MODULE_ENABLED */ +/*#define HAL_SD_MODULE_ENABLED */ +/*#define HAL_MMC_MODULE_ENABLED */ +/*#define HAL_SDRAM_MODULE_ENABLED */ +/*#define HAL_SMARTCARD_MODULE_ENABLED */ +/*#define HAL_SPI_MODULE_ENABLED */ +/*#define HAL_SRAM_MODULE_ENABLED */ +#define HAL_TIM_MODULE_ENABLED +/*#define HAL_UART_MODULE_ENABLED */ +/*#define HAL_USART_MODULE_ENABLED */ +/*#define HAL_WWDG_MODULE_ENABLED */ +/*#define HAL_EXTI_MODULE_ENABLED */ + +#define HAL_CORTEX_MODULE_ENABLED +#define HAL_DMA_MODULE_ENABLED +#define HAL_FLASH_MODULE_ENABLED +#define HAL_EXTI_MODULE_ENABLED +#define HAL_GPIO_MODULE_ENABLED +#define HAL_PWR_MODULE_ENABLED +#define HAL_RCC_MODULE_ENABLED + +/* ########################## Oscillator Values adaptation ####################*/ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) +#define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) +#define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) +#define HSI_VALUE ((uint32_t)8000000) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#if !defined (LSI_VALUE) +#define LSI_VALUE 40000U /*!< LSI Typical Value in Hz */ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz +The real value may vary depending on the variations +in voltage and temperature. */ + +/** + * @brief External Low Speed oscillator (LSE) value. + * This value is used by the UART, RTC HAL module to compute the system frequency + */ +#if !defined (LSE_VALUE) +#define LSE_VALUE ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/ +#endif /* LSE_VALUE */ + +#if !defined (LSE_STARTUP_TIMEOUT) +#define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY ((uint32_t)0) /*!< tick interrupt priority (lowest by default) */ +#define USE_RTOS 0 +#define PREFETCH_ENABLE 1 + +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ +#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ +#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ +#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ +#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ +#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ +#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ +#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ +#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ +#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ +#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ +#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ +#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ +#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1U */ + +/* ################## Ethernet peripheral configuration ##################### */ + +/* Section 1 : Ethernet peripheral configuration */ + +/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ +#define MAC_ADDR0 2 +#define MAC_ADDR1 0 +#define MAC_ADDR2 0 +#define MAC_ADDR3 0 +#define MAC_ADDR4 0 +#define MAC_ADDR5 0 + +/* Definition of the Ethernet driver buffers size and count */ +#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ +#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ +#define ETH_RXBUFNB ((uint32_t)8) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ +#define ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ + +/* Section 2: PHY configuration section */ + +/* DP83848_PHY_ADDRESS Address*/ +#define DP83848_PHY_ADDRESS 0x01U +/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ +#define PHY_RESET_DELAY ((uint32_t)0x000000FF) +/* PHY Configuration delay */ +#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF) + +#define PHY_READ_TO ((uint32_t)0x0000FFFF) +#define PHY_WRITE_TO ((uint32_t)0x0000FFFF) + +/* Section 3: Common PHY Registers */ + +#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */ +#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */ + +#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ +#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ +#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ +#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ +#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ +#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ +#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ +#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ +#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ +#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ + +#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ +#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ +#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ + +/* Section 4: Extended PHY Registers */ +#define PHY_SR ((uint16_t)0x10U) /*!< PHY status register Offset */ + +#define PHY_SPEED_STATUS ((uint16_t)0x0002U) /*!< PHY Speed mask */ +#define PHY_DUPLEX_STATUS ((uint16_t)0x0004U) /*!< PHY Duplex mask */ + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver +* Activated: CRC code is present inside driver +* Deactivated: CRC code cleaned from driver +*/ + +#define USE_SPI_CRC 0U + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED +#include "stm32f1xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED +#include "stm32f1xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_EXTI_MODULE_ENABLED +#include "stm32f1xx_hal_exti.h" +#endif /* HAL_EXTI_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED +#include "stm32f1xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED +#include "stm32f1xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED +#include "stm32f1xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CAN_LEGACY_MODULE_ENABLED +#include "Legacy/stm32f1xx_hal_can_legacy.h" +#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED +#include "stm32f1xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED +#include "stm32f1xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED +#include "stm32f1xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED +#include "stm32f1xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED +#include "stm32f1xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED +#include "stm32f1xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED +#include "stm32f1xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED +#include "stm32f1xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED +#include "stm32f1xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED +#include "stm32f1xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED +#include "stm32f1xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED +#include "stm32f1xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED +#include "stm32f1xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_PCCARD_MODULE_ENABLED +#include "stm32f1xx_hal_pccard.h" +#endif /* HAL_PCCARD_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED +#include "stm32f1xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED +#include "stm32f1xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED +#include "stm32f1xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED +#include "stm32f1xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED +#include "stm32f1xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED +#include "stm32f1xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED +#include "stm32f1xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED +#include "stm32f1xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED +#include "stm32f1xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED +#include "stm32f1xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED +#include "stm32f1xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_MMC_MODULE_ENABLED +#include "stm32f1xx_hal_mmc.h" +#endif /* HAL_MMC_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ +#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ +void assert_failed(uint8_t* file, uint32_t line); +#else +#define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F1xx_HAL_CONF_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Core/Inc/stm32f1xx_it.h b/EpsilonLights/Core/Inc/stm32f1xx_it.h new file mode 100644 index 00000000..c5b5b023 --- /dev/null +++ b/EpsilonLights/Core/Inc/stm32f1xx_it.h @@ -0,0 +1,69 @@ +/* USER CODE BEGIN Header */ +/** + ****************************************************************************** + * @file stm32f1xx_it.h + * @brief This file contains the headers of the interrupt handlers. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2020 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under Ultimate Liberty license + * SLA0044, the "License"; You may not use this file except in compliance with + * the License. You may obtain a copy of the License at: + * www.st.com/SLA0044 + * + ****************************************************************************** + */ +/* USER CODE END Header */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F1xx_IT_H +#define __STM32F1xx_IT_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Private includes ----------------------------------------------------------*/ +/* USER CODE BEGIN Includes */ + +/* USER CODE END Includes */ + +/* Exported types ------------------------------------------------------------*/ +/* USER CODE BEGIN ET */ + +/* USER CODE END ET */ + +/* Exported constants --------------------------------------------------------*/ +/* USER CODE BEGIN EC */ + +/* USER CODE END EC */ + +/* Exported macro ------------------------------------------------------------*/ +/* USER CODE BEGIN EM */ + +/* USER CODE END EM */ + +/* Exported functions prototypes ---------------------------------------------*/ +void NMI_Handler(void); +void HardFault_Handler(void); +void MemManage_Handler(void); +void BusFault_Handler(void); +void UsageFault_Handler(void); +void DebugMon_Handler(void); +void USB_HP_CAN1_TX_IRQHandler(void); +void USB_LP_CAN1_RX0_IRQHandler(void); +void TIM2_IRQHandler(void); +/* USER CODE BEGIN EFP */ + +/* USER CODE END EFP */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F1xx_IT_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Src/Lights.c b/EpsilonLights/Core/Src/Lights.c similarity index 73% rename from EpsilonLights/Src/Lights.c rename to EpsilonLights/Core/Src/Lights.c index c8691a87..22a7f2b5 100644 --- a/EpsilonLights/Src/Lights.c +++ b/EpsilonLights/Core/Src/Lights.c @@ -8,8 +8,7 @@ void updateLightsTask(void const* arg) uint32_t prevWakeTime = osKernelSysTick(); // Store inputs values char headlightsOff; - char headlightsLow; - char headlightsHigh; + char headlights; char rightSignal; char leftSignal; char hazards; @@ -26,8 +25,7 @@ void updateLightsTask(void const* arg) osDelayUntil(&prevWakeTime, LIGHTS_UPDATE_FREQ); headlightsOff = (lightsInputs >> HOFF_INPUT_INDEX) & 1; - headlightsLow = (lightsInputs >> HLOW_INPUT_INDEX) & 1; - headlightsHigh = (lightsInputs >> HHIGH_INPUT_INDEX) & 1; + headlights = (lightsInputs >> HLOW_INPUT_INDEX) & 1; rightSignal = (lightsInputs >> RSIGNAL_INPUT_INDEX) & 1; leftSignal = (lightsInputs >> LSIGNAL_INPUT_INDEX) & 1; hazards = (lightsInputs >> HAZARDS_INPUT_INDEX) & 1; @@ -38,19 +36,11 @@ void updateLightsTask(void const* arg) /* UPDATE HEADLIGHTS */ if ((headlightsOff)) { - HAL_GPIO_WritePin(HHIGH_GPIO_Port, HHIGH_Pin, LIGHT_OFF); - HAL_GPIO_WritePin(HLOW_GPIO_Port, HLOW_Pin, LIGHT_OFF); - } - else if ((headlightsLow && headlightsHigh)) - { - // Error state, turn only the low headlights on. - HAL_GPIO_WritePin(HHIGH_GPIO_Port, HHIGH_Pin, LIGHT_OFF); - HAL_GPIO_WritePin(HLOW_GPIO_Port, HLOW_Pin, LIGHT_ON); + HAL_GPIO_WritePin(HEAD_GPIO_Port, HEAD_Pin, LIGHT_OFF); } else { - HAL_GPIO_WritePin(HHIGH_GPIO_Port, HHIGH_Pin, headlightsHigh); - HAL_GPIO_WritePin(HLOW_GPIO_Port, HLOW_Pin, headlightsLow); + HAL_GPIO_WritePin(HEAD_GPIO_Port, HEAD_Pin, headlights); } /* UPDATE BRAKE LIGHTS */ @@ -82,11 +72,11 @@ void updateLightsTask(void const* arg) /* UPDATE BMS STROBE */ if (bmsStrobe) { - HAL_GPIO_WritePin(ESTROBE_GPIO_Port, ESTROBE_Pin, LIGHT_ON); + HAL_GPIO_WritePin(STROBE_GPIO_Port, STROBE_Pin, LIGHT_ON); } else { - HAL_GPIO_WritePin(ESTROBE_GPIO_Port, ESTROBE_Pin, LIGHT_OFF); + HAL_GPIO_WritePin(STROBE_GPIO_Port, STROBE_Pin, LIGHT_OFF); } } } @@ -183,11 +173,11 @@ void updateStrobeLight(void const* arg) /*Update BMS Strobe*/ if (strobeLight && (blinkerTimer <= BLINKER_FREQ)) { - HAL_GPIO_WritePin(ESTROBE_GPIO_Port, ESTROBE_Pin, LIGHT_ON); + HAL_GPIO_WritePin(STROBE_GPIO_Port, STROBE_Pin, LIGHT_ON); } else { - HAL_GPIO_WritePin(ESTROBE_GPIO_Port, ESTROBE_Pin, LIGHT_OFF); + HAL_GPIO_WritePin(STROBE_GPIO_Port, STROBE_Pin, LIGHT_OFF); } // Update blinker timer @@ -219,28 +209,37 @@ void reportLightsToCanTask(void const* arg) continue; } + if (HAL_CAN_GetTxMailboxesFreeLevel(&hcan) == 0) + { + osMutexRelease(canHandleMutex); + continue; + } + + // Toggle blue LED for every CAN message sent HAL_GPIO_TogglePin(LED_BLUE_GPIO_Port, LED_BLUE_Pin); // Set CAN msg address - hcan2.pTxMsg->StdId = LIGHTS_STATUS_STDID; + canTxHdr.StdId = LIGHTS_STATUS_STDID; + uint8_t data [1]; + uint32_t mailbox; // Initalize to avoid garbage values in [6] anad [7] LightsStatus stat = {0}; // Read lights gpios - stat.lowBeams = HAL_GPIO_ReadPin(HLOW_GPIO_Port, HLOW_Pin); - stat.highBeams = HAL_GPIO_ReadPin(HHIGH_GPIO_Port, HHIGH_Pin); + stat.lowBeams = HAL_GPIO_ReadPin(HEAD_GPIO_Port, HEAD_Pin); + stat.highBeams = 0; stat.brakes = HAL_GPIO_ReadPin(BRAKE_GPIO_Port, BRAKE_Pin); stat.leftSignal = HAL_GPIO_ReadPin(LSIGNAL_GPIO_Port, LSIGNAL_Pin); stat.rightSignal = HAL_GPIO_ReadPin(RSIGNAL_GPIO_Port, RSIGNAL_Pin); - stat.bmsStrobeLight = HAL_GPIO_ReadPin(ESTROBE_GPIO_Port, ESTROBE_Pin); - hcan2.pTxMsg->Data[0] = 0; - hcan2.pTxMsg->Data[0] += stat.lowBeams * 0x01; - hcan2.pTxMsg->Data[0] += stat.highBeams * 0x02; - hcan2.pTxMsg->Data[0] += stat.brakes * 0x04; - hcan2.pTxMsg->Data[0] += stat.leftSignal * 0x08; - hcan2.pTxMsg->Data[0] += stat.rightSignal * 0x10; - hcan2.pTxMsg->Data[0] += stat.bmsStrobeLight * 0x20; + stat.bmsStrobeLight = HAL_GPIO_ReadPin(STROBE_GPIO_Port, STROBE_Pin); + data[0] = 0; + data[0] += stat.lowBeams * 0x01; + data[0] += stat.highBeams * 0x02; + data[0] += stat.brakes * 0x04; + data[0] += stat.leftSignal * 0x08; + data[0] += stat.rightSignal * 0x10; + data[0] += stat.bmsStrobeLight * 0x20; // Send CAN msg - HAL_CAN_Transmit_IT(&hcan2); + HAL_CAN_AddTxMessage(&hcan, &canTxHdr, data, &mailbox); osMutexRelease(canHandleMutex); } } @@ -261,52 +260,61 @@ void sendHeartbeatTask(void const* arg) continue; } + if (HAL_CAN_GetTxMailboxesFreeLevel(&hcan) == 0) + { + osMutexRelease(canHandleMutex); + continue; + } + // Toggle green LED for every heartbeat sent HAL_GPIO_TogglePin(LED_GREEN_GPIO_Port, LED_GREEN_Pin); // Set CAN msg address - hcan2.pTxMsg->StdId = LIGHTS_HEARTBEAT_STDID; + canTxHdr.StdId = LIGHTS_HEARTBEAT_STDID; // Always 1 - hcan2.pTxMsg->Data[0] = 1; + uint8_t data [1] = {1}; + uint32_t mailbox; // Send CAN msg - HAL_CAN_Transmit_IT(&hcan2); + HAL_CAN_AddTxMessage(&hcan, &canTxHdr, data, &mailbox); osMutexRelease(canHandleMutex); } } // Reimplement weak definition in stm32f4xx_hal_can.c -void HAL_CAN_RxCpltCallback(CAN_HandleTypeDef* hcan) +void HAL_CAN_RxFifo0MsgPendingCallback(CAN_HandleTypeDef* hcan) { - CanRxMsgTypeDef* msg = hcan->pRxMsg; + CAN_RxHeaderTypeDef hdr; + uint8_t data[8] = {0}; + + if (HAL_CAN_GetRxMessage(hcan, CAN_RX_FIFO0, &hdr, data) != HAL_OK) + { + return; + } - if (msg->StdId == LIGHTS_INPUT_STDID && msg->DLC == 1) + if (hdr.StdId == LIGHTS_INPUT_STDID && hdr.DLC == 1) { - lightsInputs = msg->Data[0]; + lightsInputs = data[0]; } - else if (msg->StdId == BATTERY_STAT_ERRORS_STDID && msg->DLC == 5) + else if (hdr.StdId == BATTERY_STAT_ERRORS_STDID && hdr.DLC == 5) { - batteryErrors[0] = msg->Data[0]; - batteryErrors[1] = msg->Data[1]; - batteryErrors[2] = msg->Data[2]; - batteryErrors[3] = msg->Data[3]; - batteryErrors[4] = msg->Data[4]; + batteryErrors[0] = data[0]; + batteryErrors[1] = data[1]; + batteryErrors[2] = data[2]; + batteryErrors[3] = data[3]; + batteryErrors[4] = data[4]; } - else if (msg->StdId == DRIVERS_INPUTS_STDID && msg->DLC == 4) + else if (hdr.StdId == DRIVERS_INPUTS_STDID && hdr.DLC == 4) { - driversInputs[0] = msg->Data[0]; - driversInputs[1] = msg->Data[1]; - driversInputs[2] = msg->Data[2]; - driversInputs[3] = msg->Data[3]; + driversInputs[0] = data[0]; + driversInputs[1] = data[1]; + driversInputs[2] = data[2]; + driversInputs[3] = data[3]; } - else if (msg->StdId == AUXBMS_INPUT_STDID && msg->DLC == 2) + else if (hdr.StdId == AUXBMS_INPUT_STDID && hdr.DLC == 2) { - auxBmsInputs[0] = msg->Data[0]; - auxBmsInputs[1] = msg->Data[1]; + auxBmsInputs[0] = data[0]; + auxBmsInputs[1] = data[1]; } - __HAL_CAN_CLEAR_FLAG(hcan, CAN_FLAG_FMP0); - if (HAL_CAN_Receive_IT(hcan, CAN_FIFO0) != HAL_OK) - { - HAL_GPIO_TogglePin(LED_RED_GPIO_Port, LED_RED_Pin); - } + HAL_GPIO_TogglePin(LED_RED_GPIO_Port, LED_RED_Pin); } diff --git a/EpsilonLights/Core/Src/freertos.c b/EpsilonLights/Core/Src/freertos.c new file mode 100644 index 00000000..e7ec12d9 --- /dev/null +++ b/EpsilonLights/Core/Src/freertos.c @@ -0,0 +1,61 @@ +/* USER CODE BEGIN Header */ +/** + ****************************************************************************** + * File Name : freertos.c + * Description : Code for freertos applications + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2020 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under Ultimate Liberty license + * SLA0044, the "License"; You may not use this file except in compliance with + * the License. You may obtain a copy of the License at: + * www.st.com/SLA0044 + * + ****************************************************************************** + */ +/* USER CODE END Header */ + +/* Includes ------------------------------------------------------------------*/ +#include "FreeRTOS.h" +#include "task.h" +#include "main.h" + +/* Private includes ----------------------------------------------------------*/ +/* USER CODE BEGIN Includes */ + +/* USER CODE END Includes */ + +/* Private typedef -----------------------------------------------------------*/ +/* USER CODE BEGIN PTD */ + +/* USER CODE END PTD */ + +/* Private define ------------------------------------------------------------*/ +/* USER CODE BEGIN PD */ + +/* USER CODE END PD */ + +/* Private macro -------------------------------------------------------------*/ +/* USER CODE BEGIN PM */ + +/* USER CODE END PM */ + +/* Private variables ---------------------------------------------------------*/ +/* USER CODE BEGIN Variables */ + +/* USER CODE END Variables */ + +/* Private function prototypes -----------------------------------------------*/ +/* USER CODE BEGIN FunctionPrototypes */ + +/* USER CODE END FunctionPrototypes */ + +/* Private application code --------------------------------------------------*/ +/* USER CODE BEGIN Application */ + +/* USER CODE END Application */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Src/main.c b/EpsilonLights/Core/Src/main.c similarity index 51% rename from EpsilonLights/Src/main.c rename to EpsilonLights/Core/Src/main.c index 3c6e7fab..e709a5fa 100644 --- a/EpsilonLights/Src/main.c +++ b/EpsilonLights/Core/Src/main.c @@ -1,48 +1,52 @@ +/* USER CODE BEGIN Header */ /** ****************************************************************************** - * File Name : main.c - * Description : Main program body + * @file : main.c + * @brief : Main program body ****************************************************************************** + * @attention * - * COPYRIGHT(c) 2016 STMicroelectronics + *

© Copyright (c) 2020 STMicroelectronics. + * All rights reserved.

* - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * This software component is licensed by ST under Ultimate Liberty license + * SLA0044, the "License"; You may not use this file except in compliance with + * the License. You may obtain a copy of the License at: + * www.st.com/SLA0044 * ****************************************************************************** */ +/* USER CODE END Header */ + /* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" +#include "main.h" #include "cmsis_os.h" +/* Private includes ----------------------------------------------------------*/ /* USER CODE BEGIN Includes */ #include "Lights.h" /* USER CODE END Includes */ +/* Private typedef -----------------------------------------------------------*/ +/* USER CODE BEGIN PTD */ + +/* USER CODE END PTD */ + +/* Private define ------------------------------------------------------------*/ +/* USER CODE BEGIN PD */ + +/* USER CODE END PD */ + +/* Private macro -------------------------------------------------------------*/ +/* USER CODE BEGIN PM */ + +/* USER CODE END PM */ + /* Private variables ---------------------------------------------------------*/ -CAN_HandleTypeDef hcan2; +CAN_HandleTypeDef hcan; +osThreadId defaultTaskHandle; /* USER CODE BEGIN PV */ -/* Private variables ---------------------------------------------------------*/ uint8_t lightsInputs; // Initialized to 0 uint8_t batteryErrors[5]; //Initialized to {0,0,0,0,0} uint8_t driversInputs[4]; // Initialized to 0 @@ -54,49 +58,75 @@ static osThreadId lightsTaskHandle; static osThreadId lightsCanTaskHandle; static osThreadId heartbeatHandle; static osThreadId blinkLightsHandle; -static osThreadId strobeLightHandle; + +CAN_TxHeaderTypeDef canTxHdr; + /* USER CODE END PV */ /* Private function prototypes -----------------------------------------------*/ void SystemClock_Config(void); -void Error_Handler(void); static void MX_GPIO_Init(void); -static void MX_CAN2_Init(void); +static void MX_CAN_Init(void); +void StartDefaultTask(void const* argument); /* USER CODE BEGIN PFP */ -static void MX_CAN2_UserInit(void); -/* Private function prototypes -----------------------------------------------*/ - +static void MX_CAN_UserInit(void); /* USER CODE END PFP */ +/* Private user code ---------------------------------------------------------*/ /* USER CODE BEGIN 0 */ /* USER CODE END 0 */ +/** + * @brief The application entry point. + * @retval int + */ int main(void) { /* USER CODE BEGIN 1 */ + /* USER CODE END 1 */ - /* MCU Configuration----------------------------------------------------------*/ + + + /* MCU Configuration--------------------------------------------------------*/ + /* Reset of all peripherals, Initializes the Flash interface and the Systick. */ HAL_Init(); + + /* USER CODE BEGIN Init */ + + /* USER CODE END Init */ + /* Configure the system clock */ SystemClock_Config(); + + /* USER CODE BEGIN SysInit */ + + /* USER CODE END SysInit */ + /* Initialize all configured peripherals */ MX_GPIO_Init(); - MX_CAN2_Init(); + MX_CAN_Init(); /* USER CODE BEGIN 2 */ - MX_CAN2_UserInit(); + MX_CAN_UserInit(); // Setup for next CAN Receive Interrupt - if (HAL_CAN_Receive_IT(&hcan2, CAN_FIFO0) != HAL_OK) + if (HAL_CAN_ActivateNotification(&hcan, (CAN_IT_RX_FIFO0_MSG_PENDING | + CAN_IT_ERROR_WARNING | + CAN_IT_ERROR_PASSIVE | + CAN_IT_BUSOFF | + CAN_IT_LAST_ERROR_CODE | + CAN_IT_ERROR) != HAL_OK)) { /* Reception Error */ Error_Handler(); } /* USER CODE END 2 */ + /* USER CODE BEGIN RTOS_MUTEX */ + /* add mutexes, ... */ // For concurrency between sendHeartbeat() and reportLightsToCan() osMutexId canHandleMutex; osMutexDef(canHandleMutex); @@ -108,14 +138,24 @@ int main(void) } /* USER CODE END RTOS_MUTEX */ + /* USER CODE BEGIN RTOS_SEMAPHORES */ /* add semaphores, ... */ /* USER CODE END RTOS_SEMAPHORES */ + /* USER CODE BEGIN RTOS_TIMERS */ /* start timers, add new ones, ... */ /* USER CODE END RTOS_TIMERS */ + + /* USER CODE BEGIN RTOS_QUEUES */ + /* add queues, ... */ + /* USER CODE END RTOS_QUEUES */ + /* Create the thread(s) */ /* definition and creation of defaultTask */ + osThreadDef(defaultTask, StartDefaultTask, osPriorityNormal, 0, 128); + defaultTaskHandle = osThreadCreate(osThread(defaultTask), NULL); + /* USER CODE BEGIN RTOS_THREADS */ // Setup task to update physical lights osThreadDef(lightsTask, updateLightsTask, osPriorityNormal, 1, configMINIMAL_STACK_SIZE); @@ -129,13 +169,9 @@ int main(void) // Setup task to handle blinking left and right signal lights osThreadDef(blinkLightsTask, blinkSignalLightsTask, osPriorityNormal, 1, configMINIMAL_STACK_SIZE); blinkLightsHandle = osThreadCreate(osThread(blinkLightsTask), NULL); - //Setup task to update strobe light - // osThreadDef(strobeLightTask, updateStrobeLight, osPriorityNormal, 1, configMINIMAL_STACK_SIZE); - // strobeLightHandle = osThreadCreate(osThread(strobeLightTask), NULL); + /* USER CODE END RTOS_THREADS */ - /* USER CODE BEGIN RTOS_QUEUES */ - /* add queues, ... */ - /* USER CODE END RTOS_QUEUES */ + /* Start scheduler */ osKernelStart(); @@ -146,140 +182,135 @@ int main(void) while (1) { /* USER CODE END WHILE */ + /* USER CODE BEGIN 3 */ } /* USER CODE END 3 */ } -/** System Clock Configuration -*/ +/** + * @brief System Clock Configuration + * @retval None + */ void SystemClock_Config(void) { - RCC_OscInitTypeDef RCC_OscInitStruct; - RCC_ClkInitTypeDef RCC_ClkInitStruct; - __HAL_RCC_PWR_CLK_ENABLE(); - __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + RCC_OscInitTypeDef RCC_OscInitStruct = {0}; + RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; + + /** Initializes the CPU, AHB and APB busses clocks + */ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV2; + RCC_OscInitStruct.HSIState = RCC_HSI_ON; RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; - RCC_OscInitStruct.PLL.PLLM = 8; - RCC_OscInitStruct.PLL.PLLN = 320; - RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; - RCC_OscInitStruct.PLL.PLLQ = 7; + RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL5; if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { Error_Handler(); } + /** Initializes the CPU, AHB and APB busses clocks + */ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2; RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; - RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; - RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV8; - RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV4; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV2; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; - if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) + if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0) != HAL_OK) { Error_Handler(); } - - HAL_SYSTICK_Config(HAL_RCC_GetHCLKFreq() / 1000); - HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK); - /* SysTick_IRQn interrupt configuration */ - HAL_NVIC_SetPriority(SysTick_IRQn, 15, 0); } -/* CAN2 init function */ -static void MX_CAN2_Init(void) +/** + * @brief CAN Initialization Function + * @param None + * @retval None + */ +static void MX_CAN_Init(void) { - hcan2.Instance = CAN2; - hcan2.Init.Prescaler = 4; - hcan2.Init.Mode = CAN_MODE_NORMAL; - hcan2.Init.SJW = CAN_SJW_1TQ; - hcan2.Init.BS1 = CAN_BS1_5TQ; - hcan2.Init.BS2 = CAN_BS2_4TQ; - hcan2.Init.TTCM = DISABLE; - hcan2.Init.ABOM = DISABLE; - hcan2.Init.AWUM = DISABLE; - hcan2.Init.NART = DISABLE; - hcan2.Init.RFLM = DISABLE; - hcan2.Init.TXFP = DISABLE; - - if (HAL_CAN_Init(&hcan2) != HAL_OK) + + /* USER CODE BEGIN CAN_Init 0 */ + + /* USER CODE END CAN_Init 0 */ + + /* USER CODE BEGIN CAN_Init 1 */ + + /* USER CODE END CAN_Init 1 */ + hcan.Instance = CAN1; + hcan.Init.Prescaler = 2; + hcan.Init.Mode = CAN_MODE_LOOPBACK; + hcan.Init.SyncJumpWidth = CAN_SJW_1TQ; + hcan.Init.TimeSeg1 = CAN_BS1_5TQ; + hcan.Init.TimeSeg2 = CAN_BS2_4TQ; + hcan.Init.TimeTriggeredMode = DISABLE; + hcan.Init.AutoBusOff = DISABLE; + hcan.Init.AutoWakeUp = DISABLE; + hcan.Init.AutoRetransmission = DISABLE; + hcan.Init.ReceiveFifoLocked = DISABLE; + hcan.Init.TransmitFifoPriority = DISABLE; + + if (HAL_CAN_Init(&hcan) != HAL_OK) { Error_Handler(); } + + /* USER CODE BEGIN CAN_Init 2 */ + + /* USER CODE END CAN_Init 2 */ + } -/** Configure pins as - * Analog - * Input - * Output - * EVENT_OUT - * EXTI -*/ +/** + * @brief GPIO Initialization Function + * @param None + * @retval None + */ static void MX_GPIO_Init(void) { - GPIO_InitTypeDef GPIO_InitStruct; + GPIO_InitTypeDef GPIO_InitStruct = {0}; + /* GPIO Ports Clock Enable */ - __HAL_RCC_GPIOH_CLK_ENABLE(); - __HAL_RCC_GPIOC_CLK_ENABLE(); + __HAL_RCC_GPIOD_CLK_ENABLE(); __HAL_RCC_GPIOA_CLK_ENABLE(); __HAL_RCC_GPIOB_CLK_ENABLE(); - __HAL_RCC_GPIOD_CLK_ENABLE(); - __HAL_RCC_GPIOE_CLK_ENABLE(); - /*Configure GPIO pin Output Level */ - HAL_GPIO_WritePin(OTG_FS_PowerSwitchOn_GPIO_Port, OTG_FS_PowerSwitchOn_Pin, GPIO_PIN_RESET); + /*Configure GPIO pin Output Level */ HAL_GPIO_WritePin(GPIOA, LED_RED_Pin | LED_GREEN_Pin | LED_BLUE_Pin, GPIO_PIN_RESET); + /*Configure GPIO pin Output Level */ - HAL_GPIO_WritePin(GPIOD, RSIGNAL_Pin | LSIGNAL_Pin | BRAKE_Pin | HHIGH_Pin - | HLOW_Pin | ESTROBE_Pin, GPIO_PIN_RESET); - /*Configure GPIO pin : OTG_FS_PowerSwitchOn_Pin */ - GPIO_InitStruct.Pin = OTG_FS_PowerSwitchOn_Pin; - GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; - HAL_GPIO_Init(OTG_FS_PowerSwitchOn_GPIO_Port, &GPIO_InitStruct); - /*Configure GPIO pin : B1_Pin */ - GPIO_InitStruct.Pin = B1_Pin; - GPIO_InitStruct.Mode = GPIO_MODE_EVT_RISING; - GPIO_InitStruct.Pull = GPIO_NOPULL; - HAL_GPIO_Init(B1_GPIO_Port, &GPIO_InitStruct); + HAL_GPIO_WritePin(GPIOB, RSIGNAL_Pin | LSIGNAL_Pin | BRAKE_Pin | HEAD_Pin + | STROBE_Pin, GPIO_PIN_RESET); + /*Configure GPIO pins : LED_RED_Pin LED_GREEN_Pin LED_BLUE_Pin */ GPIO_InitStruct.Pin = LED_RED_Pin | LED_GREEN_Pin | LED_BLUE_Pin; GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; GPIO_InitStruct.Pull = GPIO_NOPULL; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - /*Configure GPIO pin : BOOT1_Pin */ - GPIO_InitStruct.Pin = BOOT1_Pin; - GPIO_InitStruct.Mode = GPIO_MODE_INPUT; - GPIO_InitStruct.Pull = GPIO_NOPULL; - HAL_GPIO_Init(BOOT1_GPIO_Port, &GPIO_InitStruct); - /*Configure GPIO pins : RSIGNAL_Pin LSIGNAL_Pin BRAKE_Pin HHIGH_Pin - HLOW_Pin ESTROBE_Pin */ - GPIO_InitStruct.Pin = RSIGNAL_Pin | LSIGNAL_Pin | BRAKE_Pin | HHIGH_Pin - | HLOW_Pin | ESTROBE_Pin; + + /*Configure GPIO pins : RSIGNAL_Pin LSIGNAL_Pin BRAKE_Pin HEAD_Pin + STROBE_Pin */ + GPIO_InitStruct.Pin = RSIGNAL_Pin | LSIGNAL_Pin | BRAKE_Pin | HEAD_Pin + | STROBE_Pin; GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; GPIO_InitStruct.Pull = GPIO_NOPULL; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; - HAL_GPIO_Init(GPIOD, &GPIO_InitStruct); - /*Configure GPIO pin : MEMS_INT2_Pin */ - GPIO_InitStruct.Pin = MEMS_INT2_Pin; - GPIO_InitStruct.Mode = GPIO_MODE_EVT_RISING; - GPIO_InitStruct.Pull = GPIO_NOPULL; - HAL_GPIO_Init(MEMS_INT2_GPIO_Port, &GPIO_InitStruct); + HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); + } /* USER CODE BEGIN 4 */ -static void MX_CAN2_UserInit(void) +static void MX_CAN_UserInit(void) { - CAN_FilterConfTypeDef sFilterConfig; - sFilterConfig.FilterNumber = 0; // Use first filter bank + CAN_FilterTypeDef sFilterConfig; + sFilterConfig.FilterBank = 0; // Use first filter bank sFilterConfig.FilterMode = CAN_FILTERMODE_IDLIST; // Look for specific can messages // sFilterConfig.FilterMode = CAN_FILTERMODE_IDMASK; sFilterConfig.FilterScale = CAN_FILTERSCALE_32BIT; @@ -291,10 +322,10 @@ static void MX_CAN2_UserInit(void) sFilterConfig.FilterMaskIdLow = 0; // Unused sFilterConfig.FilterFIFOAssignment = 0; sFilterConfig.FilterActivation = ENABLE; - sFilterConfig.BankNumber = 0; // Set all filter banks for CAN2 + sFilterConfig.SlaveStartFilterBank = 0; // Set all filter banks for CAN2 - CAN_FilterConfTypeDef batteryFilterConfig; - batteryFilterConfig.FilterNumber = 1; // Use secondary filter bank + CAN_FilterTypeDef batteryFilterConfig; + batteryFilterConfig.FilterBank = 1; // Use secondary filter bank batteryFilterConfig.FilterScale = CAN_FILTERSCALE_32BIT; batteryFilterConfig.FilterMode = CAN_FILTERMODE_IDLIST; // Look for specific can messages batteryFilterConfig.FilterIdHigh = AUXBMS_INPUT_STDID << 5; // Filter registers need to be shifted left 5 bits @@ -303,16 +334,16 @@ static void MX_CAN2_UserInit(void) batteryFilterConfig.FilterMaskIdLow = 0; //unused batteryFilterConfig.FilterFIFOAssignment = 0; batteryFilterConfig.FilterActivation = ENABLE; - batteryFilterConfig.BankNumber = 0; // Set all filter banks for CAN2 + batteryFilterConfig.SlaveStartFilterBank = 0; // Set all filter banks for CAN2 - if (HAL_CAN_ConfigFilter(&hcan2, &sFilterConfig) != HAL_OK) + if (HAL_CAN_ConfigFilter(&hcan, &sFilterConfig) != HAL_OK) { /* Filter configuration Error */ Error_Handler(); } - if (HAL_CAN_ConfigFilter(&hcan2, &batteryFilterConfig) != HAL_OK) + if (HAL_CAN_ConfigFilter(&hcan, &batteryFilterConfig) != HAL_OK) { /* Filter configuration Error */ Error_Handler(); @@ -320,61 +351,90 @@ static void MX_CAN2_UserInit(void) /* Configure Transmission process */ - static CanTxMsgTypeDef txMessage; - static CanRxMsgTypeDef rxMessage; - hcan2.pTxMsg = &txMessage; - hcan2.pRxMsg = &rxMessage; - // hcan2.pTxMsg->StdId = 0x0; // CAN message address, set in Lights.c - hcan2.pTxMsg->ExtId = 0x0; // Only used if (hcan2.pTxMsg->IDE == CAN_ID_EXT) - hcan2.pTxMsg->RTR = CAN_RTR_DATA; // Data request, not remote request - hcan2.pTxMsg->IDE = CAN_ID_STD; // Standard CAN, not Extended - hcan2.pTxMsg->DLC = 1; // Data size in bytes + // canTxHdr.StdId = 0x0; // CAN message address, set in Lights.c + + + canTxHdr.ExtId = 0x0; // Only used if (canTxHdr.IDE == CAN_ID_EXT) + canTxHdr.RTR = CAN_RTR_DATA; // Data request, not remote request + canTxHdr.IDE = CAN_ID_STD; // Standard CAN, not Extended + canTxHdr.TransmitGlobalTime = DISABLE; + canTxHdr.DLC = 1; } /* USER CODE END 4 */ +/* USER CODE BEGIN Header_StartDefaultTask */ /** - * @brief This function is executed in case of error occurrence. - * @param None + * @brief Function implementing the defaultTask thread. + * @param argument: Not used * @retval None */ -void Error_Handler(void) +/* USER CODE END Header_StartDefaultTask */ +void StartDefaultTask(void const* argument) { - /* USER CODE BEGIN Error_Handler */ - /* User can add his own implementation to report the HAL error return state */ - // Turn on red LED when error - // HAL_GPIO_WritePin(LED_RED_GPIO_Port, LED_RED_Pin, 1); - while (1) + + + + + /* USER CODE BEGIN 5 */ + /* Infinite loop */ + for (;;) { + osDelay(1); } - /* USER CODE END Error_Handler */ + /* USER CODE END 5 */ } -#ifdef USE_FULL_ASSERT - /** - * @brief Reports the name of the source file and the source line number - * where the assert_param error has occurred. - * @param file: pointer to the source file name - * @param line: assert_param error line source number - * @retval None - */ -void assert_failed(uint8_t* file, uint32_t line) + * @brief Period elapsed callback in non blocking mode + * @note This function is called when TIM2 interrupt took place, inside + * HAL_TIM_IRQHandler(). It makes a direct call to HAL_IncTick() to increment + * a global variable "uwTick" used as application time base. + * @param htim : TIM handle + * @retval None + */ +void HAL_TIM_PeriodElapsedCallback(TIM_HandleTypeDef* htim) { - /* USER CODE BEGIN 6 */ - /* User can add his own implementation to report the file name and line number, - ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ - /* USER CODE END 6 */ -} + /* USER CODE BEGIN Callback 0 */ + + /* USER CODE END Callback 0 */ + if (htim->Instance == TIM2) + { + HAL_IncTick(); + } -#endif + /* USER CODE BEGIN Callback 1 */ + + /* USER CODE END Callback 1 */ +} /** - * @} + * @brief This function is executed in case of error occurrence. + * @retval None */ +void Error_Handler(void) +{ + /* USER CODE BEGIN Error_Handler_Debug */ + /* User can add his own implementation to report the HAL error return state */ + /* USER CODE END Error_Handler_Debug */ +} + +#ifdef USE_FULL_ASSERT /** - * @} -*/ + * @brief Reports the name of the source file and the source line number + * where the assert_param error has occurred. + * @param file: pointer to the source file name + * @param line: assert_param error line source number + * @retval None + */ +void assert_failed(uint8_t* file, uint32_t line) +{ + /* USER CODE BEGIN 6 */ + /* User can add his own implementation to report the file name and line number, + tex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ + /* USER CODE END 6 */ +} +#endif /* USE_FULL_ASSERT */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Core/Src/stm32f1xx_hal_msp.c b/EpsilonLights/Core/Src/stm32f1xx_hal_msp.c new file mode 100644 index 00000000..727224b8 --- /dev/null +++ b/EpsilonLights/Core/Src/stm32f1xx_hal_msp.c @@ -0,0 +1,167 @@ +/* USER CODE BEGIN Header */ +/** + ****************************************************************************** + * File Name : stm32f1xx_hal_msp.c + * Description : This file provides code for the MSP Initialization + * and de-Initialization codes. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2020 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under Ultimate Liberty license + * SLA0044, the "License"; You may not use this file except in compliance with + * the License. You may obtain a copy of the License at: + * www.st.com/SLA0044 + * + ****************************************************************************** + */ +/* USER CODE END Header */ + +/* Includes ------------------------------------------------------------------*/ +#include "main.h" +/* USER CODE BEGIN Includes */ + +/* USER CODE END Includes */ + +/* Private typedef -----------------------------------------------------------*/ +/* USER CODE BEGIN TD */ + +/* USER CODE END TD */ + +/* Private define ------------------------------------------------------------*/ +/* USER CODE BEGIN Define */ + +/* USER CODE END Define */ + +/* Private macro -------------------------------------------------------------*/ +/* USER CODE BEGIN Macro */ + +/* USER CODE END Macro */ + +/* Private variables ---------------------------------------------------------*/ +/* USER CODE BEGIN PV */ + +/* USER CODE END PV */ + +/* Private function prototypes -----------------------------------------------*/ +/* USER CODE BEGIN PFP */ + +/* USER CODE END PFP */ + +/* External functions --------------------------------------------------------*/ +/* USER CODE BEGIN ExternalFunctions */ + +/* USER CODE END ExternalFunctions */ + +/* USER CODE BEGIN 0 */ + +/* USER CODE END 0 */ +/** + * Initializes the Global MSP. + */ +void HAL_MspInit(void) +{ + /* USER CODE BEGIN MspInit 0 */ + + /* USER CODE END MspInit 0 */ + + __HAL_RCC_AFIO_CLK_ENABLE(); + __HAL_RCC_PWR_CLK_ENABLE(); + + /* System interrupt init*/ + /* PendSV_IRQn interrupt configuration */ + HAL_NVIC_SetPriority(PendSV_IRQn, 15, 0); + + /** NONJTRST: Full SWJ (JTAG-DP + SW-DP) but without NJTRST + */ + __HAL_AFIO_REMAP_SWJ_NONJTRST(); + + /* USER CODE BEGIN MspInit 1 */ + + /* USER CODE END MspInit 1 */ +} + +/** +* @brief CAN MSP Initialization +* This function configures the hardware resources used in this example +* @param hcan: CAN handle pointer +* @retval None +*/ +void HAL_CAN_MspInit(CAN_HandleTypeDef* hcan) +{ + GPIO_InitTypeDef GPIO_InitStruct = {0}; + + if (hcan->Instance == CAN1) + { + /* USER CODE BEGIN CAN1_MspInit 0 */ + + /* USER CODE END CAN1_MspInit 0 */ + /* Peripheral clock enable */ + __HAL_RCC_CAN1_CLK_ENABLE(); + + __HAL_RCC_GPIOA_CLK_ENABLE(); + /**CAN GPIO Configuration + PA11 ------> CAN_RX + PA12 ------> CAN_TX + */ + GPIO_InitStruct.Pin = GPIO_PIN_11; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + GPIO_InitStruct.Pin = GPIO_PIN_12; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* CAN1 interrupt Init */ + HAL_NVIC_SetPriority(USB_HP_CAN1_TX_IRQn, 5, 0); + HAL_NVIC_EnableIRQ(USB_HP_CAN1_TX_IRQn); + HAL_NVIC_SetPriority(USB_LP_CAN1_RX0_IRQn, 5, 0); + HAL_NVIC_EnableIRQ(USB_LP_CAN1_RX0_IRQn); + /* USER CODE BEGIN CAN1_MspInit 1 */ + + /* USER CODE END CAN1_MspInit 1 */ + } + +} + +/** +* @brief CAN MSP De-Initialization +* This function freeze the hardware resources used in this example +* @param hcan: CAN handle pointer +* @retval None +*/ +void HAL_CAN_MspDeInit(CAN_HandleTypeDef* hcan) +{ + if (hcan->Instance == CAN1) + { + /* USER CODE BEGIN CAN1_MspDeInit 0 */ + + /* USER CODE END CAN1_MspDeInit 0 */ + /* Peripheral clock disable */ + __HAL_RCC_CAN1_CLK_DISABLE(); + + /**CAN GPIO Configuration + PA11 ------> CAN_RX + PA12 ------> CAN_TX + */ + HAL_GPIO_DeInit(GPIOA, GPIO_PIN_11 | GPIO_PIN_12); + + /* CAN1 interrupt DeInit */ + HAL_NVIC_DisableIRQ(USB_HP_CAN1_TX_IRQn); + HAL_NVIC_DisableIRQ(USB_LP_CAN1_RX0_IRQn); + /* USER CODE BEGIN CAN1_MspDeInit 1 */ + + /* USER CODE END CAN1_MspDeInit 1 */ + } + +} + +/* USER CODE BEGIN 1 */ + +/* USER CODE END 1 */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Src/stm32f4xx_hal_timebase_TIM.c b/EpsilonLights/Core/Src/stm32f1xx_hal_timebase_tim.c similarity index 58% rename from EpsilonLights/Src/stm32f4xx_hal_timebase_TIM.c rename to EpsilonLights/Core/Src/stm32f1xx_hal_timebase_tim.c index ccd0e270..6f693da0 100644 --- a/EpsilonLights/Src/stm32f4xx_hal_timebase_TIM.c +++ b/EpsilonLights/Core/Src/stm32f1xx_hal_timebase_tim.c @@ -1,53 +1,32 @@ +/* USER CODE BEGIN Header */ /** ****************************************************************************** - * @file stm32f4xx_hal_timebase_TIM.c + * @file stm32f1xx_hal_timebase_TIM.c * @brief HAL time base based on the hardware TIM. ****************************************************************************** + * @attention * - * COPYRIGHT(c) 2016 STMicroelectronics + *

© Copyright (c) 2020 STMicroelectronics. + * All rights reserved.

* - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * This software component is licensed by ST under Ultimate Liberty license + * SLA0044, the "License"; You may not use this file except in compliance with + * the License. You may obtain a copy of the License at: + * www.st.com/SLA0044 * ****************************************************************************** */ +/* USER CODE END Header */ /* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" -#include "stm32f4xx_hal_tim.h" -/** @addtogroup STM32F7xx_HAL_Examples - * @{ - */ - -/** @addtogroup HAL_TimeBase - * @{ - */ +#include "stm32f1xx_hal.h" +#include "stm32f1xx_hal_tim.h" /* Private typedef -----------------------------------------------------------*/ /* Private define ------------------------------------------------------------*/ /* Private macro -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ TIM_HandleTypeDef htim2; -uint32_t uwIncrementState = 0; /* Private function prototypes -----------------------------------------------*/ /* Private functions ---------------------------------------------------------*/ @@ -57,7 +36,7 @@ uint32_t uwIncrementState = 0; * Tick interrupt priority. * @note This function is called automatically at the beginning of program after * reset by HAL_Init() or at any time when clock is configured, by HAL_RCC_ClockConfig(). - * @param TickPriority: Tick interrupt priorty. + * @param TickPriority: Tick interrupt priority. * @retval HAL status */ HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority) @@ -66,20 +45,28 @@ HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority) uint32_t uwTimclock = 0; uint32_t uwPrescalerValue = 0; uint32_t pFLatency; + /*Configure the TIM2 IRQ priority */ HAL_NVIC_SetPriority(TIM2_IRQn, TickPriority, 0); + /* Enable the TIM2 global Interrupt */ HAL_NVIC_EnableIRQ(TIM2_IRQn); + /* Enable TIM2 clock */ __HAL_RCC_TIM2_CLK_ENABLE(); + /* Get clock configuration */ HAL_RCC_GetClockConfig(&clkconfig, &pFLatency); + /* Compute TIM2 clock */ - uwTimclock = 2 * HAL_RCC_GetPCLK1Freq(); + uwTimclock = HAL_RCC_GetPCLK1Freq(); + /* Compute the prescaler value to have TIM2 counter clock equal to 1MHz */ uwPrescalerValue = (uint32_t) ((uwTimclock / 1000000) - 1); + /* Initialize TIM2 */ htim2.Instance = TIM2; + /* Initialize TIMx peripheral as follow: + Period = [(TIM2CLK/1000) - 1]. to have a (1/1000) s time base. + Prescaler = (uwTimclock/1000000 - 1) to have a 1MHz counter clock. @@ -125,25 +112,4 @@ void HAL_ResumeTick(void) __HAL_TIM_ENABLE_IT(&htim2, TIM_IT_UPDATE); } -/** - * @brief Period elapsed callback in non blocking mode - * @note This function is called when TIM2 interrupt took place, inside - * HAL_TIM_IRQHandler(). It makes a direct call to HAL_IncTick() to increment - * a global variable "uwTick" used as application time base. - * @param htim : TIM handle - * @retval None - */ -void HAL_TIM_PeriodElapsedCallback(TIM_HandleTypeDef* htim) -{ - HAL_IncTick(); -} - -/** - * @} - */ - -/** - * @} - */ - /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Core/Src/stm32f1xx_it.c b/EpsilonLights/Core/Src/stm32f1xx_it.c new file mode 100644 index 00000000..4cf3f817 --- /dev/null +++ b/EpsilonLights/Core/Src/stm32f1xx_it.c @@ -0,0 +1,209 @@ +/* USER CODE BEGIN Header */ +/** + ****************************************************************************** + * @file stm32f1xx_it.c + * @brief Interrupt Service Routines. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2020 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under Ultimate Liberty license + * SLA0044, the "License"; You may not use this file except in compliance with + * the License. You may obtain a copy of the License at: + * www.st.com/SLA0044 + * + ****************************************************************************** + */ +/* USER CODE END Header */ + +/* Includes ------------------------------------------------------------------*/ +#include "main.h" +#include "stm32f1xx_it.h" +#include "FreeRTOS.h" +#include "task.h" +/* Private includes ----------------------------------------------------------*/ +/* USER CODE BEGIN Includes */ +/* USER CODE END Includes */ + +/* Private typedef -----------------------------------------------------------*/ +/* USER CODE BEGIN TD */ + +/* USER CODE END TD */ + +/* Private define ------------------------------------------------------------*/ +/* USER CODE BEGIN PD */ + +/* USER CODE END PD */ + +/* Private macro -------------------------------------------------------------*/ +/* USER CODE BEGIN PM */ + +/* USER CODE END PM */ + +/* Private variables ---------------------------------------------------------*/ +/* USER CODE BEGIN PV */ + +/* USER CODE END PV */ + +/* Private function prototypes -----------------------------------------------*/ +/* USER CODE BEGIN PFP */ + +/* USER CODE END PFP */ + +/* Private user code ---------------------------------------------------------*/ +/* USER CODE BEGIN 0 */ + +/* USER CODE END 0 */ + +/* External variables --------------------------------------------------------*/ +extern CAN_HandleTypeDef hcan; +extern TIM_HandleTypeDef htim2; + +/* USER CODE BEGIN EV */ + +/* USER CODE END EV */ + +/******************************************************************************/ +/* Cortex-M3 Processor Interruption and Exception Handlers */ +/******************************************************************************/ +/** + * @brief This function handles Non maskable interrupt. + */ +void NMI_Handler(void) +{ + /* USER CODE BEGIN NonMaskableInt_IRQn 0 */ + + /* USER CODE END NonMaskableInt_IRQn 0 */ + /* USER CODE BEGIN NonMaskableInt_IRQn 1 */ + + /* USER CODE END NonMaskableInt_IRQn 1 */ +} + +/** + * @brief This function handles Hard fault interrupt. + */ +void HardFault_Handler(void) +{ + /* USER CODE BEGIN HardFault_IRQn 0 */ + + /* USER CODE END HardFault_IRQn 0 */ + while (1) + { + /* USER CODE BEGIN W1_HardFault_IRQn 0 */ + /* USER CODE END W1_HardFault_IRQn 0 */ + } +} + +/** + * @brief This function handles Memory management fault. + */ +void MemManage_Handler(void) +{ + /* USER CODE BEGIN MemoryManagement_IRQn 0 */ + + /* USER CODE END MemoryManagement_IRQn 0 */ + while (1) + { + /* USER CODE BEGIN W1_MemoryManagement_IRQn 0 */ + /* USER CODE END W1_MemoryManagement_IRQn 0 */ + } +} + +/** + * @brief This function handles Prefetch fault, memory access fault. + */ +void BusFault_Handler(void) +{ + /* USER CODE BEGIN BusFault_IRQn 0 */ + + /* USER CODE END BusFault_IRQn 0 */ + while (1) + { + /* USER CODE BEGIN W1_BusFault_IRQn 0 */ + /* USER CODE END W1_BusFault_IRQn 0 */ + } +} + +/** + * @brief This function handles Undefined instruction or illegal state. + */ +void UsageFault_Handler(void) +{ + /* USER CODE BEGIN UsageFault_IRQn 0 */ + + /* USER CODE END UsageFault_IRQn 0 */ + while (1) + { + /* USER CODE BEGIN W1_UsageFault_IRQn 0 */ + /* USER CODE END W1_UsageFault_IRQn 0 */ + } +} + +/** + * @brief This function handles Debug monitor. + */ +void DebugMon_Handler(void) +{ + /* USER CODE BEGIN DebugMonitor_IRQn 0 */ + + /* USER CODE END DebugMonitor_IRQn 0 */ + /* USER CODE BEGIN DebugMonitor_IRQn 1 */ + + /* USER CODE END DebugMonitor_IRQn 1 */ +} + +/******************************************************************************/ +/* STM32F1xx Peripheral Interrupt Handlers */ +/* Add here the Interrupt Handlers for the used peripherals. */ +/* For the available peripheral interrupt handler names, */ +/* please refer to the startup file (startup_stm32f1xx.s). */ +/******************************************************************************/ + +/** + * @brief This function handles USB high priority or CAN TX interrupts. + */ +void USB_HP_CAN1_TX_IRQHandler(void) +{ + /* USER CODE BEGIN USB_HP_CAN1_TX_IRQn 0 */ + + /* USER CODE END USB_HP_CAN1_TX_IRQn 0 */ + HAL_CAN_IRQHandler(&hcan); + /* USER CODE BEGIN USB_HP_CAN1_TX_IRQn 1 */ + + /* USER CODE END USB_HP_CAN1_TX_IRQn 1 */ +} + +/** + * @brief This function handles USB low priority or CAN RX0 interrupts. + */ +void USB_LP_CAN1_RX0_IRQHandler(void) +{ + /* USER CODE BEGIN USB_LP_CAN1_RX0_IRQn 0 */ + + /* USER CODE END USB_LP_CAN1_RX0_IRQn 0 */ + HAL_CAN_IRQHandler(&hcan); + /* USER CODE BEGIN USB_LP_CAN1_RX0_IRQn 1 */ + + /* USER CODE END USB_LP_CAN1_RX0_IRQn 1 */ +} + +/** + * @brief This function handles TIM2 global interrupt. + */ +void TIM2_IRQHandler(void) +{ + /* USER CODE BEGIN TIM2_IRQn 0 */ + + /* USER CODE END TIM2_IRQn 0 */ + HAL_TIM_IRQHandler(&htim2); + /* USER CODE BEGIN TIM2_IRQn 1 */ + + /* USER CODE END TIM2_IRQn 1 */ +} + +/* USER CODE BEGIN 1 */ + +/* USER CODE END 1 */ +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Core/Src/system_stm32f1xx.c b/EpsilonLights/Core/Src/system_stm32f1xx.c new file mode 100644 index 00000000..81705eb5 --- /dev/null +++ b/EpsilonLights/Core/Src/system_stm32f1xx.c @@ -0,0 +1,440 @@ +/** + ****************************************************************************** + * @file system_stm32f1xx.c + * @author MCD Application Team + * @brief CMSIS Cortex-M3 Device Peripheral Access Layer System Source File. + * + * 1. This file provides two functions and one global variable to be called from + * user application: + * - SystemInit(): Setups the system clock (System clock source, PLL Multiplier + * factors, AHB/APBx prescalers and Flash settings). + * This function is called at startup just after reset and + * before branch to main program. This call is made inside + * the "startup_stm32f1xx_xx.s" file. + * + * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used + * by the user application to setup the SysTick + * timer or configure other parameters. + * + * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must + * be called whenever the core clock is changed + * during program execution. + * + * 2. After each device reset the HSI (8 MHz) is used as system clock source. + * Then SystemInit() function is called, in "startup_stm32f1xx_xx.s" file, to + * configure the system clock before to branch to main program. + * + * 4. The default value of HSE crystal is set to 8 MHz (or 25 MHz, depending on + * the product used), refer to "HSE_VALUE". + * When HSE is used as system clock source, directly or through PLL, and you + * are using different crystal you have to adapt the HSE value to your own + * configuration. + * + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2017 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/** @addtogroup CMSIS + * @{ + */ + +/** @addtogroup stm32f1xx_system + * @{ + */ + +/** @addtogroup STM32F1xx_System_Private_Includes + * @{ + */ + +#include "stm32f1xx.h" + +/** + * @} + */ + +/** @addtogroup STM32F1xx_System_Private_TypesDefinitions + * @{ + */ + +/** + * @} + */ + +/** @addtogroup STM32F1xx_System_Private_Defines + * @{ + */ + +#if !defined (HSE_VALUE) +#define HSE_VALUE 8000000U /*!< Default value of the External oscillator in Hz. + This value can be provided and adapted by the user application. */ +#endif /* HSE_VALUE */ + +#if !defined (HSI_VALUE) +#define HSI_VALUE 8000000U /*!< Default value of the Internal oscillator in Hz. + This value can be provided and adapted by the user application. */ +#endif /* HSI_VALUE */ + +/*!< Uncomment the following line if you need to use external SRAM */ +#if defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG) +/* #define DATA_IN_ExtSRAM */ +#endif /* STM32F100xE || STM32F101xE || STM32F101xG || STM32F103xE || STM32F103xG */ + +/*!< Uncomment the following line if you need to relocate your vector Table in + Internal SRAM. */ +/* #define VECT_TAB_SRAM */ +#define VECT_TAB_OFFSET 0x00000000U /*!< Vector Table base offset field. + This value must be a multiple of 0x200. */ + + +/** + * @} + */ + +/** @addtogroup STM32F1xx_System_Private_Macros + * @{ + */ + +/** + * @} + */ + +/** @addtogroup STM32F1xx_System_Private_Variables + * @{ + */ + +/* This variable is updated in three ways: + 1) by calling CMSIS function SystemCoreClockUpdate() + 2) by calling HAL API function HAL_RCC_GetHCLKFreq() + 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency + Note: If you use this function to configure the system clock; then there + is no need to call the 2 first functions listed above, since SystemCoreClock + variable is updated automatically. +*/ +uint32_t SystemCoreClock = 16000000; +const uint8_t AHBPrescTable[16U] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9}; +const uint8_t APBPrescTable[8U] = {0, 0, 0, 0, 1, 2, 3, 4}; + +/** + * @} + */ + +/** @addtogroup STM32F1xx_System_Private_FunctionPrototypes + * @{ + */ + +#if defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG) +#ifdef DATA_IN_ExtSRAM +static void SystemInit_ExtMemCtl(void); +#endif /* DATA_IN_ExtSRAM */ +#endif /* STM32F100xE || STM32F101xE || STM32F101xG || STM32F103xE || STM32F103xG */ + +/** + * @} + */ + +/** @addtogroup STM32F1xx_System_Private_Functions + * @{ + */ + +/** + * @brief Setup the microcontroller system + * Initialize the Embedded Flash Interface, the PLL and update the + * SystemCoreClock variable. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +void SystemInit (void) +{ + /* Reset the RCC clock configuration to the default reset state(for debug purpose) */ + /* Set HSION bit */ + RCC->CR |= 0x00000001U; + + /* Reset SW, HPRE, PPRE1, PPRE2, ADCPRE and MCO bits */ +#if !defined(STM32F105xC) && !defined(STM32F107xC) + RCC->CFGR &= 0xF8FF0000U; +#else + RCC->CFGR &= 0xF0FF0000U; +#endif /* STM32F105xC */ + + /* Reset HSEON, CSSON and PLLON bits */ + RCC->CR &= 0xFEF6FFFFU; + + /* Reset HSEBYP bit */ + RCC->CR &= 0xFFFBFFFFU; + + /* Reset PLLSRC, PLLXTPRE, PLLMUL and USBPRE/OTGFSPRE bits */ + RCC->CFGR &= 0xFF80FFFFU; + +#if defined(STM32F105xC) || defined(STM32F107xC) + /* Reset PLL2ON and PLL3ON bits */ + RCC->CR &= 0xEBFFFFFFU; + + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x00FF0000U; + + /* Reset CFGR2 register */ + RCC->CFGR2 = 0x00000000U; +#elif defined(STM32F100xB) || defined(STM32F100xE) + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x009F0000U; + + /* Reset CFGR2 register */ + RCC->CFGR2 = 0x00000000U; +#else + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x009F0000U; +#endif /* STM32F105xC */ + +#if defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG) +#ifdef DATA_IN_ExtSRAM + SystemInit_ExtMemCtl(); +#endif /* DATA_IN_ExtSRAM */ +#endif + +#ifdef VECT_TAB_SRAM + SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM. */ +#else + SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH. */ +#endif +} + +/** + * @brief Update SystemCoreClock variable according to Clock Register Values. + * The SystemCoreClock variable contains the core clock (HCLK), it can + * be used by the user application to setup the SysTick timer or configure + * other parameters. + * + * @note Each time the core clock (HCLK) changes, this function must be called + * to update SystemCoreClock variable value. Otherwise, any configuration + * based on this variable will be incorrect. + * + * @note - The system frequency computed by this function is not the real + * frequency in the chip. It is calculated based on the predefined + * constant and the selected clock source: + * + * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*) + * + * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**) + * + * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) + * or HSI_VALUE(*) multiplied by the PLL factors. + * + * (*) HSI_VALUE is a constant defined in stm32f1xx.h file (default value + * 8 MHz) but the real value may vary depending on the variations + * in voltage and temperature. + * + * (**) HSE_VALUE is a constant defined in stm32f1xx.h file (default value + * 8 MHz or 25 MHz, depending on the product used), user has to ensure + * that HSE_VALUE is same as the real frequency of the crystal used. + * Otherwise, this function may have wrong result. + * + * - The result of this function could be not correct when using fractional + * value for HSE crystal. + * @param None + * @retval None + */ +void SystemCoreClockUpdate (void) +{ + uint32_t tmp = 0U, pllmull = 0U, pllsource = 0U; + +#if defined(STM32F105xC) || defined(STM32F107xC) + uint32_t prediv1source = 0U, prediv1factor = 0U, prediv2factor = 0U, pll2mull = 0U; +#endif /* STM32F105xC */ + +#if defined(STM32F100xB) || defined(STM32F100xE) + uint32_t prediv1factor = 0U; +#endif /* STM32F100xB or STM32F100xE */ + + /* Get SYSCLK source -------------------------------------------------------*/ + tmp = RCC->CFGR & RCC_CFGR_SWS; + + switch (tmp) + { + case 0x00U: /* HSI used as system clock */ + SystemCoreClock = HSI_VALUE; + break; + + case 0x04U: /* HSE used as system clock */ + SystemCoreClock = HSE_VALUE; + break; + + case 0x08U: /* PLL used as system clock */ + + /* Get PLL clock source and multiplication factor ----------------------*/ + pllmull = RCC->CFGR & RCC_CFGR_PLLMULL; + pllsource = RCC->CFGR & RCC_CFGR_PLLSRC; + +#if !defined(STM32F105xC) && !defined(STM32F107xC) + pllmull = ( pllmull >> 18U) + 2U; + + if (pllsource == 0x00U) + { + /* HSI oscillator clock divided by 2 selected as PLL clock entry */ + SystemCoreClock = (HSI_VALUE >> 1U) * pllmull; + } + else + { +#if defined(STM32F100xB) || defined(STM32F100xE) + prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1U; + /* HSE oscillator clock selected as PREDIV1 clock entry */ + SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull; +#else + + /* HSE selected as PLL clock entry */ + if ((RCC->CFGR & RCC_CFGR_PLLXTPRE) != (uint32_t)RESET) + { + /* HSE oscillator clock divided by 2 */ + SystemCoreClock = (HSE_VALUE >> 1U) * pllmull; + } + else + { + SystemCoreClock = HSE_VALUE * pllmull; + } + +#endif + } + +#else + pllmull = pllmull >> 18U; + + if (pllmull != 0x0DU) + { + pllmull += 2U; + } + else + { + /* PLL multiplication factor = PLL input clock * 6.5 */ + pllmull = 13U / 2U; + } + + if (pllsource == 0x00U) + { + /* HSI oscillator clock divided by 2 selected as PLL clock entry */ + SystemCoreClock = (HSI_VALUE >> 1U) * pllmull; + } + else + { + /* PREDIV1 selected as PLL clock entry */ + + /* Get PREDIV1 clock source and division factor */ + prediv1source = RCC->CFGR2 & RCC_CFGR2_PREDIV1SRC; + prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1U; + + if (prediv1source == 0U) + { + /* HSE oscillator clock selected as PREDIV1 clock entry */ + SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull; + } + else + { + /* PLL2 clock selected as PREDIV1 clock entry */ + + /* Get PREDIV2 division factor and PLL2 multiplication factor */ + prediv2factor = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> 4U) + 1U; + pll2mull = ((RCC->CFGR2 & RCC_CFGR2_PLL2MUL) >> 8U) + 2U; + SystemCoreClock = (((HSE_VALUE / prediv2factor) * pll2mull) / prediv1factor) * pllmull; + } + } + +#endif /* STM32F105xC */ + break; + + default: + SystemCoreClock = HSI_VALUE; + break; + } + + /* Compute HCLK clock frequency ----------------*/ + /* Get HCLK prescaler */ + tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4U)]; + /* HCLK clock frequency */ + SystemCoreClock >>= tmp; +} + +#if defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG) +/** + * @brief Setup the external memory controller. Called in startup_stm32f1xx.s + * before jump to __main + * @param None + * @retval None + */ +#ifdef DATA_IN_ExtSRAM +/** + * @brief Setup the external memory controller. + * Called in startup_stm32f1xx_xx.s/.c before jump to main. + * This function configures the external SRAM mounted on STM3210E-EVAL + * board (STM32 High density devices). This SRAM will be used as program + * data memory (including heap and stack). + * @param None + * @retval None + */ +void SystemInit_ExtMemCtl(void) +{ + __IO uint32_t tmpreg; + /*!< FSMC Bank1 NOR/SRAM3 is used for the STM3210E-EVAL, if another Bank is + required, then adjust the Register Addresses */ + + /* Enable FSMC clock */ + RCC->AHBENR = 0x00000114U; + + /* Delay after an RCC peripheral clock enabling */ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_FSMCEN); + + /* Enable GPIOD, GPIOE, GPIOF and GPIOG clocks */ + RCC->APB2ENR = 0x000001E0U; + + /* Delay after an RCC peripheral clock enabling */ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPDEN); + + (void)(tmpreg); + + /* --------------- SRAM Data lines, NOE and NWE configuration ---------------*/ + /*---------------- SRAM Address lines configuration -------------------------*/ + /*---------------- NOE and NWE configuration --------------------------------*/ + /*---------------- NE3 configuration ----------------------------------------*/ + /*---------------- NBL0, NBL1 configuration ---------------------------------*/ + + GPIOD->CRL = 0x44BB44BBU; + GPIOD->CRH = 0xBBBBBBBBU; + + GPIOE->CRL = 0xB44444BBU; + GPIOE->CRH = 0xBBBBBBBBU; + + GPIOF->CRL = 0x44BBBBBBU; + GPIOF->CRH = 0xBBBB4444U; + + GPIOG->CRL = 0x44BBBBBBU; + GPIOG->CRH = 0x444B4B44U; + + /*---------------- FSMC Configuration ---------------------------------------*/ + /*---------------- Enable FSMC Bank1_SRAM Bank ------------------------------*/ + + FSMC_Bank1->BTCR[4U] = 0x00001091U; + FSMC_Bank1->BTCR[5U] = 0x00110212U; +} +#endif /* DATA_IN_ExtSRAM */ +#endif /* STM32F100xE || STM32F101xE || STM32F101xG || STM32F103xE || STM32F103xG */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F1xx/Include/stm32f103x6.h b/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F1xx/Include/stm32f103x6.h new file mode 100644 index 00000000..7d933df4 --- /dev/null +++ b/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F1xx/Include/stm32f103x6.h @@ -0,0 +1,10107 @@ +/** + ****************************************************************************** + * @file stm32f103x6.h + * @author MCD Application Team + * @brief CMSIS Cortex-M3 Device Peripheral Access Layer Header File. + * This file contains all the peripheral register's definitions, bits + * definitions and memory mapping for STM32F1xx devices. + * + * This file contains: + * - Data structures and the address mapping for all peripherals + * - Peripheral's registers declarations and bits definition + * - Macros to access peripherals registers hardware + * + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2017 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + + +/** @addtogroup CMSIS + * @{ + */ + +/** @addtogroup stm32f103x6 + * @{ + */ + +#ifndef __STM32F103x6_H +#define __STM32F103x6_H + +#ifdef __cplusplus +extern "C" { +#endif + +/** @addtogroup Configuration_section_for_CMSIS + * @{ + */ +/** + * @brief Configuration of the Cortex-M3 Processor and Core Peripherals + */ +#define __CM3_REV 0x0200U /*!< Core Revision r2p0 */ +#define __MPU_PRESENT 0U /*!< Other STM32 devices does not provide an MPU */ +#define __NVIC_PRIO_BITS 4U /*!< STM32 uses 4 Bits for the Priority Levels */ +#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ + +/** + * @} + */ + +/** @addtogroup Peripheral_interrupt_number_definition + * @{ + */ + +/** + * @brief STM32F10x Interrupt Number Definition, according to the selected device + * in @ref Library_configuration_section + */ + +/*!< Interrupt Number Definition */ +typedef enum +{ + /****** Cortex-M3 Processor Exceptions Numbers ***************************************************/ + NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ + HardFault_IRQn = -13, /*!< 3 Cortex-M3 Hard Fault Interrupt */ + MemoryManagement_IRQn = -12, /*!< 4 Cortex-M3 Memory Management Interrupt */ + BusFault_IRQn = -11, /*!< 5 Cortex-M3 Bus Fault Interrupt */ + UsageFault_IRQn = -10, /*!< 6 Cortex-M3 Usage Fault Interrupt */ + SVCall_IRQn = -5, /*!< 11 Cortex-M3 SV Call Interrupt */ + DebugMonitor_IRQn = -4, /*!< 12 Cortex-M3 Debug Monitor Interrupt */ + PendSV_IRQn = -2, /*!< 14 Cortex-M3 Pend SV Interrupt */ + SysTick_IRQn = -1, /*!< 15 Cortex-M3 System Tick Interrupt */ + + /****** STM32 specific Interrupt Numbers *********************************************************/ + WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ + PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ + TAMPER_IRQn = 2, /*!< Tamper Interrupt */ + RTC_IRQn = 3, /*!< RTC global Interrupt */ + FLASH_IRQn = 4, /*!< FLASH global Interrupt */ + RCC_IRQn = 5, /*!< RCC global Interrupt */ + EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ + EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ + EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ + EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ + EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ + DMA1_Channel1_IRQn = 11, /*!< DMA1 Channel 1 global Interrupt */ + DMA1_Channel2_IRQn = 12, /*!< DMA1 Channel 2 global Interrupt */ + DMA1_Channel3_IRQn = 13, /*!< DMA1 Channel 3 global Interrupt */ + DMA1_Channel4_IRQn = 14, /*!< DMA1 Channel 4 global Interrupt */ + DMA1_Channel5_IRQn = 15, /*!< DMA1 Channel 5 global Interrupt */ + DMA1_Channel6_IRQn = 16, /*!< DMA1 Channel 6 global Interrupt */ + DMA1_Channel7_IRQn = 17, /*!< DMA1 Channel 7 global Interrupt */ + ADC1_2_IRQn = 18, /*!< ADC1 and ADC2 global Interrupt */ + USB_HP_CAN1_TX_IRQn = 19, /*!< USB Device High Priority or CAN1 TX Interrupts */ + USB_LP_CAN1_RX0_IRQn = 20, /*!< USB Device Low Priority or CAN1 RX0 Interrupts */ + CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ + CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ + EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ + TIM1_BRK_IRQn = 24, /*!< TIM1 Break Interrupt */ + TIM1_UP_IRQn = 25, /*!< TIM1 Update Interrupt */ + TIM1_TRG_COM_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt */ + TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ + TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ + TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ + I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ + I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ + SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ + USART1_IRQn = 37, /*!< USART1 global Interrupt */ + USART2_IRQn = 38, /*!< USART2 global Interrupt */ + EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ + RTC_Alarm_IRQn = 41, /*!< RTC Alarm through EXTI Line Interrupt */ + USBWakeUp_IRQn = 42, /*!< USB Device WakeUp from suspend through EXTI Line Interrupt */ +} IRQn_Type; + +/** + * @} + */ + +#include "core_cm3.h" +#include "system_stm32f1xx.h" +#include + +/** @addtogroup Peripheral_registers_structures + * @{ + */ + +/** + * @brief Analog to Digital Converter + */ + +typedef struct +{ + __IO uint32_t SR; + __IO uint32_t CR1; + __IO uint32_t CR2; + __IO uint32_t SMPR1; + __IO uint32_t SMPR2; + __IO uint32_t JOFR1; + __IO uint32_t JOFR2; + __IO uint32_t JOFR3; + __IO uint32_t JOFR4; + __IO uint32_t HTR; + __IO uint32_t LTR; + __IO uint32_t SQR1; + __IO uint32_t SQR2; + __IO uint32_t SQR3; + __IO uint32_t JSQR; + __IO uint32_t JDR1; + __IO uint32_t JDR2; + __IO uint32_t JDR3; + __IO uint32_t JDR4; + __IO uint32_t DR; +} ADC_TypeDef; + +typedef struct +{ + __IO uint32_t SR; /*!< ADC status register, used for ADC multimode (bits common to several ADC instances). Address offset: ADC1 base address */ + __IO uint32_t CR1; /*!< ADC control register 1, used for ADC multimode (bits common to several ADC instances). Address offset: ADC1 base address + 0x04 */ + __IO uint32_t CR2; /*!< ADC control register 2, used for ADC multimode (bits common to several ADC instances). Address offset: ADC1 base address + 0x08 */ + uint32_t RESERVED[16]; + __IO uint32_t DR; /*!< ADC data register, used for ADC multimode (bits common to several ADC instances). Address offset: ADC1 base address + 0x4C */ +} ADC_Common_TypeDef; + +/** + * @brief Backup Registers + */ + +typedef struct +{ + uint32_t RESERVED0; + __IO uint32_t DR1; + __IO uint32_t DR2; + __IO uint32_t DR3; + __IO uint32_t DR4; + __IO uint32_t DR5; + __IO uint32_t DR6; + __IO uint32_t DR7; + __IO uint32_t DR8; + __IO uint32_t DR9; + __IO uint32_t DR10; + __IO uint32_t RTCCR; + __IO uint32_t CR; + __IO uint32_t CSR; +} BKP_TypeDef; + +/** + * @brief Controller Area Network TxMailBox + */ + +typedef struct +{ + __IO uint32_t TIR; + __IO uint32_t TDTR; + __IO uint32_t TDLR; + __IO uint32_t TDHR; +} CAN_TxMailBox_TypeDef; + +/** + * @brief Controller Area Network FIFOMailBox + */ + +typedef struct +{ + __IO uint32_t RIR; + __IO uint32_t RDTR; + __IO uint32_t RDLR; + __IO uint32_t RDHR; +} CAN_FIFOMailBox_TypeDef; + +/** + * @brief Controller Area Network FilterRegister + */ + +typedef struct +{ + __IO uint32_t FR1; + __IO uint32_t FR2; +} CAN_FilterRegister_TypeDef; + +/** + * @brief Controller Area Network + */ + +typedef struct +{ + __IO uint32_t MCR; + __IO uint32_t MSR; + __IO uint32_t TSR; + __IO uint32_t RF0R; + __IO uint32_t RF1R; + __IO uint32_t IER; + __IO uint32_t ESR; + __IO uint32_t BTR; + uint32_t RESERVED0[88]; + CAN_TxMailBox_TypeDef sTxMailBox[3]; + CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; + uint32_t RESERVED1[12]; + __IO uint32_t FMR; + __IO uint32_t FM1R; + uint32_t RESERVED2; + __IO uint32_t FS1R; + uint32_t RESERVED3; + __IO uint32_t FFA1R; + uint32_t RESERVED4; + __IO uint32_t FA1R; + uint32_t RESERVED5[8]; + CAN_FilterRegister_TypeDef sFilterRegister[14]; +} CAN_TypeDef; + +/** + * @brief CRC calculation unit + */ + +typedef struct +{ + __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ + __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ + uint8_t RESERVED0; /*!< Reserved, Address offset: 0x05 */ + uint16_t RESERVED1; /*!< Reserved, Address offset: 0x06 */ + __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ +} CRC_TypeDef; + + +/** + * @brief Debug MCU + */ + +typedef struct +{ + __IO uint32_t IDCODE; + __IO uint32_t CR; +} DBGMCU_TypeDef; + +/** + * @brief DMA Controller + */ + +typedef struct +{ + __IO uint32_t CCR; + __IO uint32_t CNDTR; + __IO uint32_t CPAR; + __IO uint32_t CMAR; +} DMA_Channel_TypeDef; + +typedef struct +{ + __IO uint32_t ISR; + __IO uint32_t IFCR; +} DMA_TypeDef; + + + +/** + * @brief External Interrupt/Event Controller + */ + +typedef struct +{ + __IO uint32_t IMR; + __IO uint32_t EMR; + __IO uint32_t RTSR; + __IO uint32_t FTSR; + __IO uint32_t SWIER; + __IO uint32_t PR; +} EXTI_TypeDef; + +/** + * @brief FLASH Registers + */ + +typedef struct +{ + __IO uint32_t ACR; + __IO uint32_t KEYR; + __IO uint32_t OPTKEYR; + __IO uint32_t SR; + __IO uint32_t CR; + __IO uint32_t AR; + __IO uint32_t RESERVED; + __IO uint32_t OBR; + __IO uint32_t WRPR; +} FLASH_TypeDef; + +/** + * @brief Option Bytes Registers + */ + +typedef struct +{ + __IO uint16_t RDP; + __IO uint16_t USER; + __IO uint16_t Data0; + __IO uint16_t Data1; + __IO uint16_t WRP0; + __IO uint16_t WRP1; + __IO uint16_t WRP2; + __IO uint16_t WRP3; +} OB_TypeDef; + +/** + * @brief General Purpose I/O + */ + +typedef struct +{ + __IO uint32_t CRL; + __IO uint32_t CRH; + __IO uint32_t IDR; + __IO uint32_t ODR; + __IO uint32_t BSRR; + __IO uint32_t BRR; + __IO uint32_t LCKR; +} GPIO_TypeDef; + +/** + * @brief Alternate Function I/O + */ + +typedef struct +{ + __IO uint32_t EVCR; + __IO uint32_t MAPR; + __IO uint32_t EXTICR[4]; + uint32_t RESERVED0; + __IO uint32_t MAPR2; +} AFIO_TypeDef; +/** + * @brief Inter Integrated Circuit Interface + */ + +typedef struct +{ + __IO uint32_t CR1; + __IO uint32_t CR2; + __IO uint32_t OAR1; + __IO uint32_t OAR2; + __IO uint32_t DR; + __IO uint32_t SR1; + __IO uint32_t SR2; + __IO uint32_t CCR; + __IO uint32_t TRISE; +} I2C_TypeDef; + +/** + * @brief Independent WATCHDOG + */ + +typedef struct +{ + __IO uint32_t KR; /*!< Key register, Address offset: 0x00 */ + __IO uint32_t PR; /*!< Prescaler register, Address offset: 0x04 */ + __IO uint32_t RLR; /*!< Reload register, Address offset: 0x08 */ + __IO uint32_t SR; /*!< Status register, Address offset: 0x0C */ +} IWDG_TypeDef; + +/** + * @brief Power Control + */ + +typedef struct +{ + __IO uint32_t CR; + __IO uint32_t CSR; +} PWR_TypeDef; + +/** + * @brief Reset and Clock Control + */ + +typedef struct +{ + __IO uint32_t CR; + __IO uint32_t CFGR; + __IO uint32_t CIR; + __IO uint32_t APB2RSTR; + __IO uint32_t APB1RSTR; + __IO uint32_t AHBENR; + __IO uint32_t APB2ENR; + __IO uint32_t APB1ENR; + __IO uint32_t BDCR; + __IO uint32_t CSR; + + +} RCC_TypeDef; + +/** + * @brief Real-Time Clock + */ + +typedef struct +{ + __IO uint32_t CRH; + __IO uint32_t CRL; + __IO uint32_t PRLH; + __IO uint32_t PRLL; + __IO uint32_t DIVH; + __IO uint32_t DIVL; + __IO uint32_t CNTH; + __IO uint32_t CNTL; + __IO uint32_t ALRH; + __IO uint32_t ALRL; +} RTC_TypeDef; + +/** + * @brief Serial Peripheral Interface + */ + +typedef struct +{ + __IO uint32_t CR1; + __IO uint32_t CR2; + __IO uint32_t SR; + __IO uint32_t DR; + __IO uint32_t CRCPR; + __IO uint32_t RXCRCR; + __IO uint32_t TXCRCR; + __IO uint32_t I2SCFGR; +} SPI_TypeDef; + +/** + * @brief TIM Timers + */ +typedef struct +{ + __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ + __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ + __IO uint32_t SMCR; /*!< TIM slave Mode Control register, Address offset: 0x08 */ + __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ + __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ + __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ + __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ + __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ + __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ + __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ + __IO uint32_t PSC; /*!< TIM prescaler register, Address offset: 0x28 */ + __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ + __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ + __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ + __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ + __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ + __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ + __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ + __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ + __IO uint32_t DMAR; /*!< TIM DMA address for full transfer register, Address offset: 0x4C */ + __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ +} TIM_TypeDef; + + +/** + * @brief Universal Synchronous Asynchronous Receiver Transmitter + */ + +typedef struct +{ + __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ + __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ + __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ + __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ + __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ + __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ + __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ +} USART_TypeDef; + +/** + * @brief Universal Serial Bus Full Speed Device + */ + +typedef struct +{ + __IO uint16_t EP0R; /*!< USB Endpoint 0 register, Address offset: 0x00 */ + __IO uint16_t RESERVED0; /*!< Reserved */ + __IO uint16_t EP1R; /*!< USB Endpoint 1 register, Address offset: 0x04 */ + __IO uint16_t RESERVED1; /*!< Reserved */ + __IO uint16_t EP2R; /*!< USB Endpoint 2 register, Address offset: 0x08 */ + __IO uint16_t RESERVED2; /*!< Reserved */ + __IO uint16_t EP3R; /*!< USB Endpoint 3 register, Address offset: 0x0C */ + __IO uint16_t RESERVED3; /*!< Reserved */ + __IO uint16_t EP4R; /*!< USB Endpoint 4 register, Address offset: 0x10 */ + __IO uint16_t RESERVED4; /*!< Reserved */ + __IO uint16_t EP5R; /*!< USB Endpoint 5 register, Address offset: 0x14 */ + __IO uint16_t RESERVED5; /*!< Reserved */ + __IO uint16_t EP6R; /*!< USB Endpoint 6 register, Address offset: 0x18 */ + __IO uint16_t RESERVED6; /*!< Reserved */ + __IO uint16_t EP7R; /*!< USB Endpoint 7 register, Address offset: 0x1C */ + __IO uint16_t RESERVED7[17]; /*!< Reserved */ + __IO uint16_t CNTR; /*!< Control register, Address offset: 0x40 */ + __IO uint16_t RESERVED8; /*!< Reserved */ + __IO uint16_t ISTR; /*!< Interrupt status register, Address offset: 0x44 */ + __IO uint16_t RESERVED9; /*!< Reserved */ + __IO uint16_t FNR; /*!< Frame number register, Address offset: 0x48 */ + __IO uint16_t RESERVEDA; /*!< Reserved */ + __IO uint16_t DADDR; /*!< Device address register, Address offset: 0x4C */ + __IO uint16_t RESERVEDB; /*!< Reserved */ + __IO uint16_t BTABLE; /*!< Buffer Table address register, Address offset: 0x50 */ + __IO uint16_t RESERVEDC; /*!< Reserved */ +} USB_TypeDef; + + +/** + * @brief Window WATCHDOG + */ + +typedef struct +{ + __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ + __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ + __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ +} WWDG_TypeDef; + +/** + * @} + */ + +/** @addtogroup Peripheral_memory_map + * @{ + */ + + +#define FLASH_BASE 0x08000000UL /*!< FLASH base address in the alias region */ +#define FLASH_BANK1_END 0x08007FFFUL /*!< FLASH END address of bank1 */ +#define SRAM_BASE 0x20000000UL /*!< SRAM base address in the alias region */ +#define PERIPH_BASE 0x40000000UL /*!< Peripheral base address in the alias region */ + +#define SRAM_BB_BASE 0x22000000UL /*!< SRAM base address in the bit-band region */ +#define PERIPH_BB_BASE 0x42000000UL /*!< Peripheral base address in the bit-band region */ + + +/*!< Peripheral memory map */ +#define APB1PERIPH_BASE PERIPH_BASE +#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000UL) +#define AHBPERIPH_BASE (PERIPH_BASE + 0x00020000UL) + +#define TIM2_BASE (APB1PERIPH_BASE + 0x00000000UL) +#define TIM3_BASE (APB1PERIPH_BASE + 0x00000400UL) +#define RTC_BASE (APB1PERIPH_BASE + 0x00002800UL) +#define WWDG_BASE (APB1PERIPH_BASE + 0x00002C00UL) +#define IWDG_BASE (APB1PERIPH_BASE + 0x00003000UL) +#define USART2_BASE (APB1PERIPH_BASE + 0x00004400UL) +#define I2C1_BASE (APB1PERIPH_BASE + 0x00005400UL) +#define CAN1_BASE (APB1PERIPH_BASE + 0x00006400UL) +#define BKP_BASE (APB1PERIPH_BASE + 0x00006C00UL) +#define PWR_BASE (APB1PERIPH_BASE + 0x00007000UL) +#define AFIO_BASE (APB2PERIPH_BASE + 0x00000000UL) +#define EXTI_BASE (APB2PERIPH_BASE + 0x00000400UL) +#define GPIOA_BASE (APB2PERIPH_BASE + 0x00000800UL) +#define GPIOB_BASE (APB2PERIPH_BASE + 0x00000C00UL) +#define GPIOC_BASE (APB2PERIPH_BASE + 0x00001000UL) +#define GPIOD_BASE (APB2PERIPH_BASE + 0x00001400UL) +#define ADC1_BASE (APB2PERIPH_BASE + 0x00002400UL) +#define ADC2_BASE (APB2PERIPH_BASE + 0x00002800UL) +#define TIM1_BASE (APB2PERIPH_BASE + 0x00002C00UL) +#define SPI1_BASE (APB2PERIPH_BASE + 0x00003000UL) +#define USART1_BASE (APB2PERIPH_BASE + 0x00003800UL) + + +#define DMA1_BASE (AHBPERIPH_BASE + 0x00000000UL) +#define DMA1_Channel1_BASE (AHBPERIPH_BASE + 0x00000008UL) +#define DMA1_Channel2_BASE (AHBPERIPH_BASE + 0x0000001CUL) +#define DMA1_Channel3_BASE (AHBPERIPH_BASE + 0x00000030UL) +#define DMA1_Channel4_BASE (AHBPERIPH_BASE + 0x00000044UL) +#define DMA1_Channel5_BASE (AHBPERIPH_BASE + 0x00000058UL) +#define DMA1_Channel6_BASE (AHBPERIPH_BASE + 0x0000006CUL) +#define DMA1_Channel7_BASE (AHBPERIPH_BASE + 0x00000080UL) +#define RCC_BASE (AHBPERIPH_BASE + 0x00001000UL) +#define CRC_BASE (AHBPERIPH_BASE + 0x00003000UL) + +#define FLASH_R_BASE (AHBPERIPH_BASE + 0x00002000UL) /*!< Flash registers base address */ +#define FLASHSIZE_BASE 0x1FFFF7E0UL /*!< FLASH Size register base address */ +#define UID_BASE 0x1FFFF7E8UL /*!< Unique device ID register base address */ +#define OB_BASE 0x1FFFF800UL /*!< Flash Option Bytes base address */ + + + +#define DBGMCU_BASE 0xE0042000UL /*!< Debug MCU registers base address */ + +/* USB device FS */ +#define USB_BASE (APB1PERIPH_BASE + 0x00005C00UL) /*!< USB_IP Peripheral Registers base address */ +#define USB_PMAADDR (APB1PERIPH_BASE + 0x00006000UL) /*!< USB_IP Packet Memory Area base address */ + + +/** + * @} + */ + +/** @addtogroup Peripheral_declaration + * @{ + */ + +#define TIM2 ((TIM_TypeDef *)TIM2_BASE) +#define TIM3 ((TIM_TypeDef *)TIM3_BASE) +#define RTC ((RTC_TypeDef *)RTC_BASE) +#define WWDG ((WWDG_TypeDef *)WWDG_BASE) +#define IWDG ((IWDG_TypeDef *)IWDG_BASE) +#define USART2 ((USART_TypeDef *)USART2_BASE) +#define I2C1 ((I2C_TypeDef *)I2C1_BASE) +#define USB ((USB_TypeDef *)USB_BASE) +#define CAN1 ((CAN_TypeDef *)CAN1_BASE) +#define BKP ((BKP_TypeDef *)BKP_BASE) +#define PWR ((PWR_TypeDef *)PWR_BASE) +#define AFIO ((AFIO_TypeDef *)AFIO_BASE) +#define EXTI ((EXTI_TypeDef *)EXTI_BASE) +#define GPIOA ((GPIO_TypeDef *)GPIOA_BASE) +#define GPIOB ((GPIO_TypeDef *)GPIOB_BASE) +#define GPIOC ((GPIO_TypeDef *)GPIOC_BASE) +#define GPIOD ((GPIO_TypeDef *)GPIOD_BASE) +#define ADC1 ((ADC_TypeDef *)ADC1_BASE) +#define ADC2 ((ADC_TypeDef *)ADC2_BASE) +#define ADC12_COMMON ((ADC_Common_TypeDef *)ADC1_BASE) +#define TIM1 ((TIM_TypeDef *)TIM1_BASE) +#define SPI1 ((SPI_TypeDef *)SPI1_BASE) +#define USART1 ((USART_TypeDef *)USART1_BASE) +#define DMA1 ((DMA_TypeDef *)DMA1_BASE) +#define DMA1_Channel1 ((DMA_Channel_TypeDef *)DMA1_Channel1_BASE) +#define DMA1_Channel2 ((DMA_Channel_TypeDef *)DMA1_Channel2_BASE) +#define DMA1_Channel3 ((DMA_Channel_TypeDef *)DMA1_Channel3_BASE) +#define DMA1_Channel4 ((DMA_Channel_TypeDef *)DMA1_Channel4_BASE) +#define DMA1_Channel5 ((DMA_Channel_TypeDef *)DMA1_Channel5_BASE) +#define DMA1_Channel6 ((DMA_Channel_TypeDef *)DMA1_Channel6_BASE) +#define DMA1_Channel7 ((DMA_Channel_TypeDef *)DMA1_Channel7_BASE) +#define RCC ((RCC_TypeDef *)RCC_BASE) +#define CRC ((CRC_TypeDef *)CRC_BASE) +#define FLASH ((FLASH_TypeDef *)FLASH_R_BASE) +#define OB ((OB_TypeDef *)OB_BASE) +#define DBGMCU ((DBGMCU_TypeDef *)DBGMCU_BASE) + + +/** + * @} + */ + +/** @addtogroup Exported_constants + * @{ + */ + +/** @addtogroup Peripheral_Registers_Bits_Definition +* @{ +*/ + +/******************************************************************************/ +/* Peripheral Registers_Bits_Definition */ +/******************************************************************************/ + +/******************************************************************************/ +/* */ +/* CRC calculation unit (CRC) */ +/* */ +/******************************************************************************/ + +/******************* Bit definition for CRC_DR register *********************/ +#define CRC_DR_DR_Pos (0U) +#define CRC_DR_DR_Msk (0xFFFFFFFFUL << CRC_DR_DR_Pos) /*!< 0xFFFFFFFF */ +#define CRC_DR_DR CRC_DR_DR_Msk /*!< Data register bits */ + +/******************* Bit definition for CRC_IDR register ********************/ +#define CRC_IDR_IDR_Pos (0U) +#define CRC_IDR_IDR_Msk (0xFFUL << CRC_IDR_IDR_Pos) /*!< 0x000000FF */ +#define CRC_IDR_IDR CRC_IDR_IDR_Msk /*!< General-purpose 8-bit data register bits */ + +/******************** Bit definition for CRC_CR register ********************/ +#define CRC_CR_RESET_Pos (0U) +#define CRC_CR_RESET_Msk (0x1UL << CRC_CR_RESET_Pos) /*!< 0x00000001 */ +#define CRC_CR_RESET CRC_CR_RESET_Msk /*!< RESET bit */ + +/******************************************************************************/ +/* */ +/* Power Control */ +/* */ +/******************************************************************************/ + +/******************** Bit definition for PWR_CR register ********************/ +#define PWR_CR_LPDS_Pos (0U) +#define PWR_CR_LPDS_Msk (0x1UL << PWR_CR_LPDS_Pos) /*!< 0x00000001 */ +#define PWR_CR_LPDS PWR_CR_LPDS_Msk /*!< Low-Power Deepsleep */ +#define PWR_CR_PDDS_Pos (1U) +#define PWR_CR_PDDS_Msk (0x1UL << PWR_CR_PDDS_Pos) /*!< 0x00000002 */ +#define PWR_CR_PDDS PWR_CR_PDDS_Msk /*!< Power Down Deepsleep */ +#define PWR_CR_CWUF_Pos (2U) +#define PWR_CR_CWUF_Msk (0x1UL << PWR_CR_CWUF_Pos) /*!< 0x00000004 */ +#define PWR_CR_CWUF PWR_CR_CWUF_Msk /*!< Clear Wakeup Flag */ +#define PWR_CR_CSBF_Pos (3U) +#define PWR_CR_CSBF_Msk (0x1UL << PWR_CR_CSBF_Pos) /*!< 0x00000008 */ +#define PWR_CR_CSBF PWR_CR_CSBF_Msk /*!< Clear Standby Flag */ +#define PWR_CR_PVDE_Pos (4U) +#define PWR_CR_PVDE_Msk (0x1UL << PWR_CR_PVDE_Pos) /*!< 0x00000010 */ +#define PWR_CR_PVDE PWR_CR_PVDE_Msk /*!< Power Voltage Detector Enable */ + +#define PWR_CR_PLS_Pos (5U) +#define PWR_CR_PLS_Msk (0x7UL << PWR_CR_PLS_Pos) /*!< 0x000000E0 */ +#define PWR_CR_PLS PWR_CR_PLS_Msk /*!< PLS[2:0] bits (PVD Level Selection) */ +#define PWR_CR_PLS_0 (0x1UL << PWR_CR_PLS_Pos) /*!< 0x00000020 */ +#define PWR_CR_PLS_1 (0x2UL << PWR_CR_PLS_Pos) /*!< 0x00000040 */ +#define PWR_CR_PLS_2 (0x4UL << PWR_CR_PLS_Pos) /*!< 0x00000080 */ + +/*!< PVD level configuration */ +#define PWR_CR_PLS_LEV0 0x00000000U /*!< PVD level 2.2V */ +#define PWR_CR_PLS_LEV1 0x00000020U /*!< PVD level 2.3V */ +#define PWR_CR_PLS_LEV2 0x00000040U /*!< PVD level 2.4V */ +#define PWR_CR_PLS_LEV3 0x00000060U /*!< PVD level 2.5V */ +#define PWR_CR_PLS_LEV4 0x00000080U /*!< PVD level 2.6V */ +#define PWR_CR_PLS_LEV5 0x000000A0U /*!< PVD level 2.7V */ +#define PWR_CR_PLS_LEV6 0x000000C0U /*!< PVD level 2.8V */ +#define PWR_CR_PLS_LEV7 0x000000E0U /*!< PVD level 2.9V */ + +/* Legacy defines */ +#define PWR_CR_PLS_2V2 PWR_CR_PLS_LEV0 +#define PWR_CR_PLS_2V3 PWR_CR_PLS_LEV1 +#define PWR_CR_PLS_2V4 PWR_CR_PLS_LEV2 +#define PWR_CR_PLS_2V5 PWR_CR_PLS_LEV3 +#define PWR_CR_PLS_2V6 PWR_CR_PLS_LEV4 +#define PWR_CR_PLS_2V7 PWR_CR_PLS_LEV5 +#define PWR_CR_PLS_2V8 PWR_CR_PLS_LEV6 +#define PWR_CR_PLS_2V9 PWR_CR_PLS_LEV7 + +#define PWR_CR_DBP_Pos (8U) +#define PWR_CR_DBP_Msk (0x1UL << PWR_CR_DBP_Pos) /*!< 0x00000100 */ +#define PWR_CR_DBP PWR_CR_DBP_Msk /*!< Disable Backup Domain write protection */ + + +/******************* Bit definition for PWR_CSR register ********************/ +#define PWR_CSR_WUF_Pos (0U) +#define PWR_CSR_WUF_Msk (0x1UL << PWR_CSR_WUF_Pos) /*!< 0x00000001 */ +#define PWR_CSR_WUF PWR_CSR_WUF_Msk /*!< Wakeup Flag */ +#define PWR_CSR_SBF_Pos (1U) +#define PWR_CSR_SBF_Msk (0x1UL << PWR_CSR_SBF_Pos) /*!< 0x00000002 */ +#define PWR_CSR_SBF PWR_CSR_SBF_Msk /*!< Standby Flag */ +#define PWR_CSR_PVDO_Pos (2U) +#define PWR_CSR_PVDO_Msk (0x1UL << PWR_CSR_PVDO_Pos) /*!< 0x00000004 */ +#define PWR_CSR_PVDO PWR_CSR_PVDO_Msk /*!< PVD Output */ +#define PWR_CSR_EWUP_Pos (8U) +#define PWR_CSR_EWUP_Msk (0x1UL << PWR_CSR_EWUP_Pos) /*!< 0x00000100 */ +#define PWR_CSR_EWUP PWR_CSR_EWUP_Msk /*!< Enable WKUP pin */ + +/******************************************************************************/ +/* */ +/* Backup registers */ +/* */ +/******************************************************************************/ + +/******************* Bit definition for BKP_DR1 register ********************/ +#define BKP_DR1_D_Pos (0U) +#define BKP_DR1_D_Msk (0xFFFFUL << BKP_DR1_D_Pos) /*!< 0x0000FFFF */ +#define BKP_DR1_D BKP_DR1_D_Msk /*!< Backup data */ + +/******************* Bit definition for BKP_DR2 register ********************/ +#define BKP_DR2_D_Pos (0U) +#define BKP_DR2_D_Msk (0xFFFFUL << BKP_DR2_D_Pos) /*!< 0x0000FFFF */ +#define BKP_DR2_D BKP_DR2_D_Msk /*!< Backup data */ + +/******************* Bit definition for BKP_DR3 register ********************/ +#define BKP_DR3_D_Pos (0U) +#define BKP_DR3_D_Msk (0xFFFFUL << BKP_DR3_D_Pos) /*!< 0x0000FFFF */ +#define BKP_DR3_D BKP_DR3_D_Msk /*!< Backup data */ + +/******************* Bit definition for BKP_DR4 register ********************/ +#define BKP_DR4_D_Pos (0U) +#define BKP_DR4_D_Msk (0xFFFFUL << BKP_DR4_D_Pos) /*!< 0x0000FFFF */ +#define BKP_DR4_D BKP_DR4_D_Msk /*!< Backup data */ + +/******************* Bit definition for BKP_DR5 register ********************/ +#define BKP_DR5_D_Pos (0U) +#define BKP_DR5_D_Msk (0xFFFFUL << BKP_DR5_D_Pos) /*!< 0x0000FFFF */ +#define BKP_DR5_D BKP_DR5_D_Msk /*!< Backup data */ + +/******************* Bit definition for BKP_DR6 register ********************/ +#define BKP_DR6_D_Pos (0U) +#define BKP_DR6_D_Msk (0xFFFFUL << BKP_DR6_D_Pos) /*!< 0x0000FFFF */ +#define BKP_DR6_D BKP_DR6_D_Msk /*!< Backup data */ + +/******************* Bit definition for BKP_DR7 register ********************/ +#define BKP_DR7_D_Pos (0U) +#define BKP_DR7_D_Msk (0xFFFFUL << BKP_DR7_D_Pos) /*!< 0x0000FFFF */ +#define BKP_DR7_D BKP_DR7_D_Msk /*!< Backup data */ + +/******************* Bit definition for BKP_DR8 register ********************/ +#define BKP_DR8_D_Pos (0U) +#define BKP_DR8_D_Msk (0xFFFFUL << BKP_DR8_D_Pos) /*!< 0x0000FFFF */ +#define BKP_DR8_D BKP_DR8_D_Msk /*!< Backup data */ + +/******************* Bit definition for BKP_DR9 register ********************/ +#define BKP_DR9_D_Pos (0U) +#define BKP_DR9_D_Msk (0xFFFFUL << BKP_DR9_D_Pos) /*!< 0x0000FFFF */ +#define BKP_DR9_D BKP_DR9_D_Msk /*!< Backup data */ + +/******************* Bit definition for BKP_DR10 register *******************/ +#define BKP_DR10_D_Pos (0U) +#define BKP_DR10_D_Msk (0xFFFFUL << BKP_DR10_D_Pos) /*!< 0x0000FFFF */ +#define BKP_DR10_D BKP_DR10_D_Msk /*!< Backup data */ + +#define RTC_BKP_NUMBER 10 + +/****************** Bit definition for BKP_RTCCR register *******************/ +#define BKP_RTCCR_CAL_Pos (0U) +#define BKP_RTCCR_CAL_Msk (0x7FUL << BKP_RTCCR_CAL_Pos) /*!< 0x0000007F */ +#define BKP_RTCCR_CAL BKP_RTCCR_CAL_Msk /*!< Calibration value */ +#define BKP_RTCCR_CCO_Pos (7U) +#define BKP_RTCCR_CCO_Msk (0x1UL << BKP_RTCCR_CCO_Pos) /*!< 0x00000080 */ +#define BKP_RTCCR_CCO BKP_RTCCR_CCO_Msk /*!< Calibration Clock Output */ +#define BKP_RTCCR_ASOE_Pos (8U) +#define BKP_RTCCR_ASOE_Msk (0x1UL << BKP_RTCCR_ASOE_Pos) /*!< 0x00000100 */ +#define BKP_RTCCR_ASOE BKP_RTCCR_ASOE_Msk /*!< Alarm or Second Output Enable */ +#define BKP_RTCCR_ASOS_Pos (9U) +#define BKP_RTCCR_ASOS_Msk (0x1UL << BKP_RTCCR_ASOS_Pos) /*!< 0x00000200 */ +#define BKP_RTCCR_ASOS BKP_RTCCR_ASOS_Msk /*!< Alarm or Second Output Selection */ + +/******************** Bit definition for BKP_CR register ********************/ +#define BKP_CR_TPE_Pos (0U) +#define BKP_CR_TPE_Msk (0x1UL << BKP_CR_TPE_Pos) /*!< 0x00000001 */ +#define BKP_CR_TPE BKP_CR_TPE_Msk /*!< TAMPER pin enable */ +#define BKP_CR_TPAL_Pos (1U) +#define BKP_CR_TPAL_Msk (0x1UL << BKP_CR_TPAL_Pos) /*!< 0x00000002 */ +#define BKP_CR_TPAL BKP_CR_TPAL_Msk /*!< TAMPER pin active level */ + +/******************* Bit definition for BKP_CSR register ********************/ +#define BKP_CSR_CTE_Pos (0U) +#define BKP_CSR_CTE_Msk (0x1UL << BKP_CSR_CTE_Pos) /*!< 0x00000001 */ +#define BKP_CSR_CTE BKP_CSR_CTE_Msk /*!< Clear Tamper event */ +#define BKP_CSR_CTI_Pos (1U) +#define BKP_CSR_CTI_Msk (0x1UL << BKP_CSR_CTI_Pos) /*!< 0x00000002 */ +#define BKP_CSR_CTI BKP_CSR_CTI_Msk /*!< Clear Tamper Interrupt */ +#define BKP_CSR_TPIE_Pos (2U) +#define BKP_CSR_TPIE_Msk (0x1UL << BKP_CSR_TPIE_Pos) /*!< 0x00000004 */ +#define BKP_CSR_TPIE BKP_CSR_TPIE_Msk /*!< TAMPER Pin interrupt enable */ +#define BKP_CSR_TEF_Pos (8U) +#define BKP_CSR_TEF_Msk (0x1UL << BKP_CSR_TEF_Pos) /*!< 0x00000100 */ +#define BKP_CSR_TEF BKP_CSR_TEF_Msk /*!< Tamper Event Flag */ +#define BKP_CSR_TIF_Pos (9U) +#define BKP_CSR_TIF_Msk (0x1UL << BKP_CSR_TIF_Pos) /*!< 0x00000200 */ +#define BKP_CSR_TIF BKP_CSR_TIF_Msk /*!< Tamper Interrupt Flag */ + +/******************************************************************************/ +/* */ +/* Reset and Clock Control */ +/* */ +/******************************************************************************/ + +/******************** Bit definition for RCC_CR register ********************/ +#define RCC_CR_HSION_Pos (0U) +#define RCC_CR_HSION_Msk (0x1UL << RCC_CR_HSION_Pos) /*!< 0x00000001 */ +#define RCC_CR_HSION RCC_CR_HSION_Msk /*!< Internal High Speed clock enable */ +#define RCC_CR_HSIRDY_Pos (1U) +#define RCC_CR_HSIRDY_Msk (0x1UL << RCC_CR_HSIRDY_Pos) /*!< 0x00000002 */ +#define RCC_CR_HSIRDY RCC_CR_HSIRDY_Msk /*!< Internal High Speed clock ready flag */ +#define RCC_CR_HSITRIM_Pos (3U) +#define RCC_CR_HSITRIM_Msk (0x1FUL << RCC_CR_HSITRIM_Pos) /*!< 0x000000F8 */ +#define RCC_CR_HSITRIM RCC_CR_HSITRIM_Msk /*!< Internal High Speed clock trimming */ +#define RCC_CR_HSICAL_Pos (8U) +#define RCC_CR_HSICAL_Msk (0xFFUL << RCC_CR_HSICAL_Pos) /*!< 0x0000FF00 */ +#define RCC_CR_HSICAL RCC_CR_HSICAL_Msk /*!< Internal High Speed clock Calibration */ +#define RCC_CR_HSEON_Pos (16U) +#define RCC_CR_HSEON_Msk (0x1UL << RCC_CR_HSEON_Pos) /*!< 0x00010000 */ +#define RCC_CR_HSEON RCC_CR_HSEON_Msk /*!< External High Speed clock enable */ +#define RCC_CR_HSERDY_Pos (17U) +#define RCC_CR_HSERDY_Msk (0x1UL << RCC_CR_HSERDY_Pos) /*!< 0x00020000 */ +#define RCC_CR_HSERDY RCC_CR_HSERDY_Msk /*!< External High Speed clock ready flag */ +#define RCC_CR_HSEBYP_Pos (18U) +#define RCC_CR_HSEBYP_Msk (0x1UL << RCC_CR_HSEBYP_Pos) /*!< 0x00040000 */ +#define RCC_CR_HSEBYP RCC_CR_HSEBYP_Msk /*!< External High Speed clock Bypass */ +#define RCC_CR_CSSON_Pos (19U) +#define RCC_CR_CSSON_Msk (0x1UL << RCC_CR_CSSON_Pos) /*!< 0x00080000 */ +#define RCC_CR_CSSON RCC_CR_CSSON_Msk /*!< Clock Security System enable */ +#define RCC_CR_PLLON_Pos (24U) +#define RCC_CR_PLLON_Msk (0x1UL << RCC_CR_PLLON_Pos) /*!< 0x01000000 */ +#define RCC_CR_PLLON RCC_CR_PLLON_Msk /*!< PLL enable */ +#define RCC_CR_PLLRDY_Pos (25U) +#define RCC_CR_PLLRDY_Msk (0x1UL << RCC_CR_PLLRDY_Pos) /*!< 0x02000000 */ +#define RCC_CR_PLLRDY RCC_CR_PLLRDY_Msk /*!< PLL clock ready flag */ + + +/******************* Bit definition for RCC_CFGR register *******************/ +/*!< SW configuration */ +#define RCC_CFGR_SW_Pos (0U) +#define RCC_CFGR_SW_Msk (0x3UL << RCC_CFGR_SW_Pos) /*!< 0x00000003 */ +#define RCC_CFGR_SW RCC_CFGR_SW_Msk /*!< SW[1:0] bits (System clock Switch) */ +#define RCC_CFGR_SW_0 (0x1UL << RCC_CFGR_SW_Pos) /*!< 0x00000001 */ +#define RCC_CFGR_SW_1 (0x2UL << RCC_CFGR_SW_Pos) /*!< 0x00000002 */ + +#define RCC_CFGR_SW_HSI 0x00000000U /*!< HSI selected as system clock */ +#define RCC_CFGR_SW_HSE 0x00000001U /*!< HSE selected as system clock */ +#define RCC_CFGR_SW_PLL 0x00000002U /*!< PLL selected as system clock */ + +/*!< SWS configuration */ +#define RCC_CFGR_SWS_Pos (2U) +#define RCC_CFGR_SWS_Msk (0x3UL << RCC_CFGR_SWS_Pos) /*!< 0x0000000C */ +#define RCC_CFGR_SWS RCC_CFGR_SWS_Msk /*!< SWS[1:0] bits (System Clock Switch Status) */ +#define RCC_CFGR_SWS_0 (0x1UL << RCC_CFGR_SWS_Pos) /*!< 0x00000004 */ +#define RCC_CFGR_SWS_1 (0x2UL << RCC_CFGR_SWS_Pos) /*!< 0x00000008 */ + +#define RCC_CFGR_SWS_HSI 0x00000000U /*!< HSI oscillator used as system clock */ +#define RCC_CFGR_SWS_HSE 0x00000004U /*!< HSE oscillator used as system clock */ +#define RCC_CFGR_SWS_PLL 0x00000008U /*!< PLL used as system clock */ + +/*!< HPRE configuration */ +#define RCC_CFGR_HPRE_Pos (4U) +#define RCC_CFGR_HPRE_Msk (0xFUL << RCC_CFGR_HPRE_Pos) /*!< 0x000000F0 */ +#define RCC_CFGR_HPRE RCC_CFGR_HPRE_Msk /*!< HPRE[3:0] bits (AHB prescaler) */ +#define RCC_CFGR_HPRE_0 (0x1UL << RCC_CFGR_HPRE_Pos) /*!< 0x00000010 */ +#define RCC_CFGR_HPRE_1 (0x2UL << RCC_CFGR_HPRE_Pos) /*!< 0x00000020 */ +#define RCC_CFGR_HPRE_2 (0x4UL << RCC_CFGR_HPRE_Pos) /*!< 0x00000040 */ +#define RCC_CFGR_HPRE_3 (0x8UL << RCC_CFGR_HPRE_Pos) /*!< 0x00000080 */ + +#define RCC_CFGR_HPRE_DIV1 0x00000000U /*!< SYSCLK not divided */ +#define RCC_CFGR_HPRE_DIV2 0x00000080U /*!< SYSCLK divided by 2 */ +#define RCC_CFGR_HPRE_DIV4 0x00000090U /*!< SYSCLK divided by 4 */ +#define RCC_CFGR_HPRE_DIV8 0x000000A0U /*!< SYSCLK divided by 8 */ +#define RCC_CFGR_HPRE_DIV16 0x000000B0U /*!< SYSCLK divided by 16 */ +#define RCC_CFGR_HPRE_DIV64 0x000000C0U /*!< SYSCLK divided by 64 */ +#define RCC_CFGR_HPRE_DIV128 0x000000D0U /*!< SYSCLK divided by 128 */ +#define RCC_CFGR_HPRE_DIV256 0x000000E0U /*!< SYSCLK divided by 256 */ +#define RCC_CFGR_HPRE_DIV512 0x000000F0U /*!< SYSCLK divided by 512 */ + +/*!< PPRE1 configuration */ +#define RCC_CFGR_PPRE1_Pos (8U) +#define RCC_CFGR_PPRE1_Msk (0x7UL << RCC_CFGR_PPRE1_Pos) /*!< 0x00000700 */ +#define RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_Msk /*!< PRE1[2:0] bits (APB1 prescaler) */ +#define RCC_CFGR_PPRE1_0 (0x1UL << RCC_CFGR_PPRE1_Pos) /*!< 0x00000100 */ +#define RCC_CFGR_PPRE1_1 (0x2UL << RCC_CFGR_PPRE1_Pos) /*!< 0x00000200 */ +#define RCC_CFGR_PPRE1_2 (0x4UL << RCC_CFGR_PPRE1_Pos) /*!< 0x00000400 */ + +#define RCC_CFGR_PPRE1_DIV1 0x00000000U /*!< HCLK not divided */ +#define RCC_CFGR_PPRE1_DIV2 0x00000400U /*!< HCLK divided by 2 */ +#define RCC_CFGR_PPRE1_DIV4 0x00000500U /*!< HCLK divided by 4 */ +#define RCC_CFGR_PPRE1_DIV8 0x00000600U /*!< HCLK divided by 8 */ +#define RCC_CFGR_PPRE1_DIV16 0x00000700U /*!< HCLK divided by 16 */ + +/*!< PPRE2 configuration */ +#define RCC_CFGR_PPRE2_Pos (11U) +#define RCC_CFGR_PPRE2_Msk (0x7UL << RCC_CFGR_PPRE2_Pos) /*!< 0x00003800 */ +#define RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_Msk /*!< PRE2[2:0] bits (APB2 prescaler) */ +#define RCC_CFGR_PPRE2_0 (0x1UL << RCC_CFGR_PPRE2_Pos) /*!< 0x00000800 */ +#define RCC_CFGR_PPRE2_1 (0x2UL << RCC_CFGR_PPRE2_Pos) /*!< 0x00001000 */ +#define RCC_CFGR_PPRE2_2 (0x4UL << RCC_CFGR_PPRE2_Pos) /*!< 0x00002000 */ + +#define RCC_CFGR_PPRE2_DIV1 0x00000000U /*!< HCLK not divided */ +#define RCC_CFGR_PPRE2_DIV2 0x00002000U /*!< HCLK divided by 2 */ +#define RCC_CFGR_PPRE2_DIV4 0x00002800U /*!< HCLK divided by 4 */ +#define RCC_CFGR_PPRE2_DIV8 0x00003000U /*!< HCLK divided by 8 */ +#define RCC_CFGR_PPRE2_DIV16 0x00003800U /*!< HCLK divided by 16 */ + +/*!< ADCPPRE configuration */ +#define RCC_CFGR_ADCPRE_Pos (14U) +#define RCC_CFGR_ADCPRE_Msk (0x3UL << RCC_CFGR_ADCPRE_Pos) /*!< 0x0000C000 */ +#define RCC_CFGR_ADCPRE RCC_CFGR_ADCPRE_Msk /*!< ADCPRE[1:0] bits (ADC prescaler) */ +#define RCC_CFGR_ADCPRE_0 (0x1UL << RCC_CFGR_ADCPRE_Pos) /*!< 0x00004000 */ +#define RCC_CFGR_ADCPRE_1 (0x2UL << RCC_CFGR_ADCPRE_Pos) /*!< 0x00008000 */ + +#define RCC_CFGR_ADCPRE_DIV2 0x00000000U /*!< PCLK2 divided by 2 */ +#define RCC_CFGR_ADCPRE_DIV4 0x00004000U /*!< PCLK2 divided by 4 */ +#define RCC_CFGR_ADCPRE_DIV6 0x00008000U /*!< PCLK2 divided by 6 */ +#define RCC_CFGR_ADCPRE_DIV8 0x0000C000U /*!< PCLK2 divided by 8 */ + +#define RCC_CFGR_PLLSRC_Pos (16U) +#define RCC_CFGR_PLLSRC_Msk (0x1UL << RCC_CFGR_PLLSRC_Pos) /*!< 0x00010000 */ +#define RCC_CFGR_PLLSRC RCC_CFGR_PLLSRC_Msk /*!< PLL entry clock source */ + +#define RCC_CFGR_PLLXTPRE_Pos (17U) +#define RCC_CFGR_PLLXTPRE_Msk (0x1UL << RCC_CFGR_PLLXTPRE_Pos) /*!< 0x00020000 */ +#define RCC_CFGR_PLLXTPRE RCC_CFGR_PLLXTPRE_Msk /*!< HSE divider for PLL entry */ + +/*!< PLLMUL configuration */ +#define RCC_CFGR_PLLMULL_Pos (18U) +#define RCC_CFGR_PLLMULL_Msk (0xFUL << RCC_CFGR_PLLMULL_Pos) /*!< 0x003C0000 */ +#define RCC_CFGR_PLLMULL RCC_CFGR_PLLMULL_Msk /*!< PLLMUL[3:0] bits (PLL multiplication factor) */ +#define RCC_CFGR_PLLMULL_0 (0x1UL << RCC_CFGR_PLLMULL_Pos) /*!< 0x00040000 */ +#define RCC_CFGR_PLLMULL_1 (0x2UL << RCC_CFGR_PLLMULL_Pos) /*!< 0x00080000 */ +#define RCC_CFGR_PLLMULL_2 (0x4UL << RCC_CFGR_PLLMULL_Pos) /*!< 0x00100000 */ +#define RCC_CFGR_PLLMULL_3 (0x8UL << RCC_CFGR_PLLMULL_Pos) /*!< 0x00200000 */ + +#define RCC_CFGR_PLLXTPRE_HSE 0x00000000U /*!< HSE clock not divided for PLL entry */ +#define RCC_CFGR_PLLXTPRE_HSE_DIV2 0x00020000U /*!< HSE clock divided by 2 for PLL entry */ + +#define RCC_CFGR_PLLMULL2 0x00000000U /*!< PLL input clock*2 */ +#define RCC_CFGR_PLLMULL3_Pos (18U) +#define RCC_CFGR_PLLMULL3_Msk (0x1UL << RCC_CFGR_PLLMULL3_Pos) /*!< 0x00040000 */ +#define RCC_CFGR_PLLMULL3 RCC_CFGR_PLLMULL3_Msk /*!< PLL input clock*3 */ +#define RCC_CFGR_PLLMULL4_Pos (19U) +#define RCC_CFGR_PLLMULL4_Msk (0x1UL << RCC_CFGR_PLLMULL4_Pos) /*!< 0x00080000 */ +#define RCC_CFGR_PLLMULL4 RCC_CFGR_PLLMULL4_Msk /*!< PLL input clock*4 */ +#define RCC_CFGR_PLLMULL5_Pos (18U) +#define RCC_CFGR_PLLMULL5_Msk (0x3UL << RCC_CFGR_PLLMULL5_Pos) /*!< 0x000C0000 */ +#define RCC_CFGR_PLLMULL5 RCC_CFGR_PLLMULL5_Msk /*!< PLL input clock*5 */ +#define RCC_CFGR_PLLMULL6_Pos (20U) +#define RCC_CFGR_PLLMULL6_Msk (0x1UL << RCC_CFGR_PLLMULL6_Pos) /*!< 0x00100000 */ +#define RCC_CFGR_PLLMULL6 RCC_CFGR_PLLMULL6_Msk /*!< PLL input clock*6 */ +#define RCC_CFGR_PLLMULL7_Pos (18U) +#define RCC_CFGR_PLLMULL7_Msk (0x5UL << RCC_CFGR_PLLMULL7_Pos) /*!< 0x00140000 */ +#define RCC_CFGR_PLLMULL7 RCC_CFGR_PLLMULL7_Msk /*!< PLL input clock*7 */ +#define RCC_CFGR_PLLMULL8_Pos (19U) +#define RCC_CFGR_PLLMULL8_Msk (0x3UL << RCC_CFGR_PLLMULL8_Pos) /*!< 0x00180000 */ +#define RCC_CFGR_PLLMULL8 RCC_CFGR_PLLMULL8_Msk /*!< PLL input clock*8 */ +#define RCC_CFGR_PLLMULL9_Pos (18U) +#define RCC_CFGR_PLLMULL9_Msk (0x7UL << RCC_CFGR_PLLMULL9_Pos) /*!< 0x001C0000 */ +#define RCC_CFGR_PLLMULL9 RCC_CFGR_PLLMULL9_Msk /*!< PLL input clock*9 */ +#define RCC_CFGR_PLLMULL10_Pos (21U) +#define RCC_CFGR_PLLMULL10_Msk (0x1UL << RCC_CFGR_PLLMULL10_Pos) /*!< 0x00200000 */ +#define RCC_CFGR_PLLMULL10 RCC_CFGR_PLLMULL10_Msk /*!< PLL input clock10 */ +#define RCC_CFGR_PLLMULL11_Pos (18U) +#define RCC_CFGR_PLLMULL11_Msk (0x9UL << RCC_CFGR_PLLMULL11_Pos) /*!< 0x00240000 */ +#define RCC_CFGR_PLLMULL11 RCC_CFGR_PLLMULL11_Msk /*!< PLL input clock*11 */ +#define RCC_CFGR_PLLMULL12_Pos (19U) +#define RCC_CFGR_PLLMULL12_Msk (0x5UL << RCC_CFGR_PLLMULL12_Pos) /*!< 0x00280000 */ +#define RCC_CFGR_PLLMULL12 RCC_CFGR_PLLMULL12_Msk /*!< PLL input clock*12 */ +#define RCC_CFGR_PLLMULL13_Pos (18U) +#define RCC_CFGR_PLLMULL13_Msk (0xBUL << RCC_CFGR_PLLMULL13_Pos) /*!< 0x002C0000 */ +#define RCC_CFGR_PLLMULL13 RCC_CFGR_PLLMULL13_Msk /*!< PLL input clock*13 */ +#define RCC_CFGR_PLLMULL14_Pos (20U) +#define RCC_CFGR_PLLMULL14_Msk (0x3UL << RCC_CFGR_PLLMULL14_Pos) /*!< 0x00300000 */ +#define RCC_CFGR_PLLMULL14 RCC_CFGR_PLLMULL14_Msk /*!< PLL input clock*14 */ +#define RCC_CFGR_PLLMULL15_Pos (18U) +#define RCC_CFGR_PLLMULL15_Msk (0xDUL << RCC_CFGR_PLLMULL15_Pos) /*!< 0x00340000 */ +#define RCC_CFGR_PLLMULL15 RCC_CFGR_PLLMULL15_Msk /*!< PLL input clock*15 */ +#define RCC_CFGR_PLLMULL16_Pos (19U) +#define RCC_CFGR_PLLMULL16_Msk (0x7UL << RCC_CFGR_PLLMULL16_Pos) /*!< 0x00380000 */ +#define RCC_CFGR_PLLMULL16 RCC_CFGR_PLLMULL16_Msk /*!< PLL input clock*16 */ +#define RCC_CFGR_USBPRE_Pos (22U) +#define RCC_CFGR_USBPRE_Msk (0x1UL << RCC_CFGR_USBPRE_Pos) /*!< 0x00400000 */ +#define RCC_CFGR_USBPRE RCC_CFGR_USBPRE_Msk /*!< USB Device prescaler */ + +/*!< MCO configuration */ +#define RCC_CFGR_MCO_Pos (24U) +#define RCC_CFGR_MCO_Msk (0x7UL << RCC_CFGR_MCO_Pos) /*!< 0x07000000 */ +#define RCC_CFGR_MCO RCC_CFGR_MCO_Msk /*!< MCO[2:0] bits (Microcontroller Clock Output) */ +#define RCC_CFGR_MCO_0 (0x1UL << RCC_CFGR_MCO_Pos) /*!< 0x01000000 */ +#define RCC_CFGR_MCO_1 (0x2UL << RCC_CFGR_MCO_Pos) /*!< 0x02000000 */ +#define RCC_CFGR_MCO_2 (0x4UL << RCC_CFGR_MCO_Pos) /*!< 0x04000000 */ + +#define RCC_CFGR_MCO_NOCLOCK 0x00000000U /*!< No clock */ +#define RCC_CFGR_MCO_SYSCLK 0x04000000U /*!< System clock selected as MCO source */ +#define RCC_CFGR_MCO_HSI 0x05000000U /*!< HSI clock selected as MCO source */ +#define RCC_CFGR_MCO_HSE 0x06000000U /*!< HSE clock selected as MCO source */ +#define RCC_CFGR_MCO_PLLCLK_DIV2 0x07000000U /*!< PLL clock divided by 2 selected as MCO source */ + +/* Reference defines */ +#define RCC_CFGR_MCOSEL RCC_CFGR_MCO +#define RCC_CFGR_MCOSEL_0 RCC_CFGR_MCO_0 +#define RCC_CFGR_MCOSEL_1 RCC_CFGR_MCO_1 +#define RCC_CFGR_MCOSEL_2 RCC_CFGR_MCO_2 +#define RCC_CFGR_MCOSEL_NOCLOCK RCC_CFGR_MCO_NOCLOCK +#define RCC_CFGR_MCOSEL_SYSCLK RCC_CFGR_MCO_SYSCLK +#define RCC_CFGR_MCOSEL_HSI RCC_CFGR_MCO_HSI +#define RCC_CFGR_MCOSEL_HSE RCC_CFGR_MCO_HSE +#define RCC_CFGR_MCOSEL_PLL_DIV2 RCC_CFGR_MCO_PLLCLK_DIV2 + +/*!<****************** Bit definition for RCC_CIR register ********************/ +#define RCC_CIR_LSIRDYF_Pos (0U) +#define RCC_CIR_LSIRDYF_Msk (0x1UL << RCC_CIR_LSIRDYF_Pos) /*!< 0x00000001 */ +#define RCC_CIR_LSIRDYF RCC_CIR_LSIRDYF_Msk /*!< LSI Ready Interrupt flag */ +#define RCC_CIR_LSERDYF_Pos (1U) +#define RCC_CIR_LSERDYF_Msk (0x1UL << RCC_CIR_LSERDYF_Pos) /*!< 0x00000002 */ +#define RCC_CIR_LSERDYF RCC_CIR_LSERDYF_Msk /*!< LSE Ready Interrupt flag */ +#define RCC_CIR_HSIRDYF_Pos (2U) +#define RCC_CIR_HSIRDYF_Msk (0x1UL << RCC_CIR_HSIRDYF_Pos) /*!< 0x00000004 */ +#define RCC_CIR_HSIRDYF RCC_CIR_HSIRDYF_Msk /*!< HSI Ready Interrupt flag */ +#define RCC_CIR_HSERDYF_Pos (3U) +#define RCC_CIR_HSERDYF_Msk (0x1UL << RCC_CIR_HSERDYF_Pos) /*!< 0x00000008 */ +#define RCC_CIR_HSERDYF RCC_CIR_HSERDYF_Msk /*!< HSE Ready Interrupt flag */ +#define RCC_CIR_PLLRDYF_Pos (4U) +#define RCC_CIR_PLLRDYF_Msk (0x1UL << RCC_CIR_PLLRDYF_Pos) /*!< 0x00000010 */ +#define RCC_CIR_PLLRDYF RCC_CIR_PLLRDYF_Msk /*!< PLL Ready Interrupt flag */ +#define RCC_CIR_CSSF_Pos (7U) +#define RCC_CIR_CSSF_Msk (0x1UL << RCC_CIR_CSSF_Pos) /*!< 0x00000080 */ +#define RCC_CIR_CSSF RCC_CIR_CSSF_Msk /*!< Clock Security System Interrupt flag */ +#define RCC_CIR_LSIRDYIE_Pos (8U) +#define RCC_CIR_LSIRDYIE_Msk (0x1UL << RCC_CIR_LSIRDYIE_Pos) /*!< 0x00000100 */ +#define RCC_CIR_LSIRDYIE RCC_CIR_LSIRDYIE_Msk /*!< LSI Ready Interrupt Enable */ +#define RCC_CIR_LSERDYIE_Pos (9U) +#define RCC_CIR_LSERDYIE_Msk (0x1UL << RCC_CIR_LSERDYIE_Pos) /*!< 0x00000200 */ +#define RCC_CIR_LSERDYIE RCC_CIR_LSERDYIE_Msk /*!< LSE Ready Interrupt Enable */ +#define RCC_CIR_HSIRDYIE_Pos (10U) +#define RCC_CIR_HSIRDYIE_Msk (0x1UL << RCC_CIR_HSIRDYIE_Pos) /*!< 0x00000400 */ +#define RCC_CIR_HSIRDYIE RCC_CIR_HSIRDYIE_Msk /*!< HSI Ready Interrupt Enable */ +#define RCC_CIR_HSERDYIE_Pos (11U) +#define RCC_CIR_HSERDYIE_Msk (0x1UL << RCC_CIR_HSERDYIE_Pos) /*!< 0x00000800 */ +#define RCC_CIR_HSERDYIE RCC_CIR_HSERDYIE_Msk /*!< HSE Ready Interrupt Enable */ +#define RCC_CIR_PLLRDYIE_Pos (12U) +#define RCC_CIR_PLLRDYIE_Msk (0x1UL << RCC_CIR_PLLRDYIE_Pos) /*!< 0x00001000 */ +#define RCC_CIR_PLLRDYIE RCC_CIR_PLLRDYIE_Msk /*!< PLL Ready Interrupt Enable */ +#define RCC_CIR_LSIRDYC_Pos (16U) +#define RCC_CIR_LSIRDYC_Msk (0x1UL << RCC_CIR_LSIRDYC_Pos) /*!< 0x00010000 */ +#define RCC_CIR_LSIRDYC RCC_CIR_LSIRDYC_Msk /*!< LSI Ready Interrupt Clear */ +#define RCC_CIR_LSERDYC_Pos (17U) +#define RCC_CIR_LSERDYC_Msk (0x1UL << RCC_CIR_LSERDYC_Pos) /*!< 0x00020000 */ +#define RCC_CIR_LSERDYC RCC_CIR_LSERDYC_Msk /*!< LSE Ready Interrupt Clear */ +#define RCC_CIR_HSIRDYC_Pos (18U) +#define RCC_CIR_HSIRDYC_Msk (0x1UL << RCC_CIR_HSIRDYC_Pos) /*!< 0x00040000 */ +#define RCC_CIR_HSIRDYC RCC_CIR_HSIRDYC_Msk /*!< HSI Ready Interrupt Clear */ +#define RCC_CIR_HSERDYC_Pos (19U) +#define RCC_CIR_HSERDYC_Msk (0x1UL << RCC_CIR_HSERDYC_Pos) /*!< 0x00080000 */ +#define RCC_CIR_HSERDYC RCC_CIR_HSERDYC_Msk /*!< HSE Ready Interrupt Clear */ +#define RCC_CIR_PLLRDYC_Pos (20U) +#define RCC_CIR_PLLRDYC_Msk (0x1UL << RCC_CIR_PLLRDYC_Pos) /*!< 0x00100000 */ +#define RCC_CIR_PLLRDYC RCC_CIR_PLLRDYC_Msk /*!< PLL Ready Interrupt Clear */ +#define RCC_CIR_CSSC_Pos (23U) +#define RCC_CIR_CSSC_Msk (0x1UL << RCC_CIR_CSSC_Pos) /*!< 0x00800000 */ +#define RCC_CIR_CSSC RCC_CIR_CSSC_Msk /*!< Clock Security System Interrupt Clear */ + + +/***************** Bit definition for RCC_APB2RSTR register *****************/ +#define RCC_APB2RSTR_AFIORST_Pos (0U) +#define RCC_APB2RSTR_AFIORST_Msk (0x1UL << RCC_APB2RSTR_AFIORST_Pos) /*!< 0x00000001 */ +#define RCC_APB2RSTR_AFIORST RCC_APB2RSTR_AFIORST_Msk /*!< Alternate Function I/O reset */ +#define RCC_APB2RSTR_IOPARST_Pos (2U) +#define RCC_APB2RSTR_IOPARST_Msk (0x1UL << RCC_APB2RSTR_IOPARST_Pos) /*!< 0x00000004 */ +#define RCC_APB2RSTR_IOPARST RCC_APB2RSTR_IOPARST_Msk /*!< I/O port A reset */ +#define RCC_APB2RSTR_IOPBRST_Pos (3U) +#define RCC_APB2RSTR_IOPBRST_Msk (0x1UL << RCC_APB2RSTR_IOPBRST_Pos) /*!< 0x00000008 */ +#define RCC_APB2RSTR_IOPBRST RCC_APB2RSTR_IOPBRST_Msk /*!< I/O port B reset */ +#define RCC_APB2RSTR_IOPCRST_Pos (4U) +#define RCC_APB2RSTR_IOPCRST_Msk (0x1UL << RCC_APB2RSTR_IOPCRST_Pos) /*!< 0x00000010 */ +#define RCC_APB2RSTR_IOPCRST RCC_APB2RSTR_IOPCRST_Msk /*!< I/O port C reset */ +#define RCC_APB2RSTR_IOPDRST_Pos (5U) +#define RCC_APB2RSTR_IOPDRST_Msk (0x1UL << RCC_APB2RSTR_IOPDRST_Pos) /*!< 0x00000020 */ +#define RCC_APB2RSTR_IOPDRST RCC_APB2RSTR_IOPDRST_Msk /*!< I/O port D reset */ +#define RCC_APB2RSTR_ADC1RST_Pos (9U) +#define RCC_APB2RSTR_ADC1RST_Msk (0x1UL << RCC_APB2RSTR_ADC1RST_Pos) /*!< 0x00000200 */ +#define RCC_APB2RSTR_ADC1RST RCC_APB2RSTR_ADC1RST_Msk /*!< ADC 1 interface reset */ + +#define RCC_APB2RSTR_ADC2RST_Pos (10U) +#define RCC_APB2RSTR_ADC2RST_Msk (0x1UL << RCC_APB2RSTR_ADC2RST_Pos) /*!< 0x00000400 */ +#define RCC_APB2RSTR_ADC2RST RCC_APB2RSTR_ADC2RST_Msk /*!< ADC 2 interface reset */ + +#define RCC_APB2RSTR_TIM1RST_Pos (11U) +#define RCC_APB2RSTR_TIM1RST_Msk (0x1UL << RCC_APB2RSTR_TIM1RST_Pos) /*!< 0x00000800 */ +#define RCC_APB2RSTR_TIM1RST RCC_APB2RSTR_TIM1RST_Msk /*!< TIM1 Timer reset */ +#define RCC_APB2RSTR_SPI1RST_Pos (12U) +#define RCC_APB2RSTR_SPI1RST_Msk (0x1UL << RCC_APB2RSTR_SPI1RST_Pos) /*!< 0x00001000 */ +#define RCC_APB2RSTR_SPI1RST RCC_APB2RSTR_SPI1RST_Msk /*!< SPI 1 reset */ +#define RCC_APB2RSTR_USART1RST_Pos (14U) +#define RCC_APB2RSTR_USART1RST_Msk (0x1UL << RCC_APB2RSTR_USART1RST_Pos) /*!< 0x00004000 */ +#define RCC_APB2RSTR_USART1RST RCC_APB2RSTR_USART1RST_Msk /*!< USART1 reset */ + + + + + + +/***************** Bit definition for RCC_APB1RSTR register *****************/ +#define RCC_APB1RSTR_TIM2RST_Pos (0U) +#define RCC_APB1RSTR_TIM2RST_Msk (0x1UL << RCC_APB1RSTR_TIM2RST_Pos) /*!< 0x00000001 */ +#define RCC_APB1RSTR_TIM2RST RCC_APB1RSTR_TIM2RST_Msk /*!< Timer 2 reset */ +#define RCC_APB1RSTR_TIM3RST_Pos (1U) +#define RCC_APB1RSTR_TIM3RST_Msk (0x1UL << RCC_APB1RSTR_TIM3RST_Pos) /*!< 0x00000002 */ +#define RCC_APB1RSTR_TIM3RST RCC_APB1RSTR_TIM3RST_Msk /*!< Timer 3 reset */ +#define RCC_APB1RSTR_WWDGRST_Pos (11U) +#define RCC_APB1RSTR_WWDGRST_Msk (0x1UL << RCC_APB1RSTR_WWDGRST_Pos) /*!< 0x00000800 */ +#define RCC_APB1RSTR_WWDGRST RCC_APB1RSTR_WWDGRST_Msk /*!< Window Watchdog reset */ +#define RCC_APB1RSTR_USART2RST_Pos (17U) +#define RCC_APB1RSTR_USART2RST_Msk (0x1UL << RCC_APB1RSTR_USART2RST_Pos) /*!< 0x00020000 */ +#define RCC_APB1RSTR_USART2RST RCC_APB1RSTR_USART2RST_Msk /*!< USART 2 reset */ +#define RCC_APB1RSTR_I2C1RST_Pos (21U) +#define RCC_APB1RSTR_I2C1RST_Msk (0x1UL << RCC_APB1RSTR_I2C1RST_Pos) /*!< 0x00200000 */ +#define RCC_APB1RSTR_I2C1RST RCC_APB1RSTR_I2C1RST_Msk /*!< I2C 1 reset */ + +#define RCC_APB1RSTR_CAN1RST_Pos (25U) +#define RCC_APB1RSTR_CAN1RST_Msk (0x1UL << RCC_APB1RSTR_CAN1RST_Pos) /*!< 0x02000000 */ +#define RCC_APB1RSTR_CAN1RST RCC_APB1RSTR_CAN1RST_Msk /*!< CAN1 reset */ + +#define RCC_APB1RSTR_BKPRST_Pos (27U) +#define RCC_APB1RSTR_BKPRST_Msk (0x1UL << RCC_APB1RSTR_BKPRST_Pos) /*!< 0x08000000 */ +#define RCC_APB1RSTR_BKPRST RCC_APB1RSTR_BKPRST_Msk /*!< Backup interface reset */ +#define RCC_APB1RSTR_PWRRST_Pos (28U) +#define RCC_APB1RSTR_PWRRST_Msk (0x1UL << RCC_APB1RSTR_PWRRST_Pos) /*!< 0x10000000 */ +#define RCC_APB1RSTR_PWRRST RCC_APB1RSTR_PWRRST_Msk /*!< Power interface reset */ + + +#define RCC_APB1RSTR_USBRST_Pos (23U) +#define RCC_APB1RSTR_USBRST_Msk (0x1UL << RCC_APB1RSTR_USBRST_Pos) /*!< 0x00800000 */ +#define RCC_APB1RSTR_USBRST RCC_APB1RSTR_USBRST_Msk /*!< USB Device reset */ + + + + + + +/****************** Bit definition for RCC_AHBENR register ******************/ +#define RCC_AHBENR_DMA1EN_Pos (0U) +#define RCC_AHBENR_DMA1EN_Msk (0x1UL << RCC_AHBENR_DMA1EN_Pos) /*!< 0x00000001 */ +#define RCC_AHBENR_DMA1EN RCC_AHBENR_DMA1EN_Msk /*!< DMA1 clock enable */ +#define RCC_AHBENR_SRAMEN_Pos (2U) +#define RCC_AHBENR_SRAMEN_Msk (0x1UL << RCC_AHBENR_SRAMEN_Pos) /*!< 0x00000004 */ +#define RCC_AHBENR_SRAMEN RCC_AHBENR_SRAMEN_Msk /*!< SRAM interface clock enable */ +#define RCC_AHBENR_FLITFEN_Pos (4U) +#define RCC_AHBENR_FLITFEN_Msk (0x1UL << RCC_AHBENR_FLITFEN_Pos) /*!< 0x00000010 */ +#define RCC_AHBENR_FLITFEN RCC_AHBENR_FLITFEN_Msk /*!< FLITF clock enable */ +#define RCC_AHBENR_CRCEN_Pos (6U) +#define RCC_AHBENR_CRCEN_Msk (0x1UL << RCC_AHBENR_CRCEN_Pos) /*!< 0x00000040 */ +#define RCC_AHBENR_CRCEN RCC_AHBENR_CRCEN_Msk /*!< CRC clock enable */ + + + + +/****************** Bit definition for RCC_APB2ENR register *****************/ +#define RCC_APB2ENR_AFIOEN_Pos (0U) +#define RCC_APB2ENR_AFIOEN_Msk (0x1UL << RCC_APB2ENR_AFIOEN_Pos) /*!< 0x00000001 */ +#define RCC_APB2ENR_AFIOEN RCC_APB2ENR_AFIOEN_Msk /*!< Alternate Function I/O clock enable */ +#define RCC_APB2ENR_IOPAEN_Pos (2U) +#define RCC_APB2ENR_IOPAEN_Msk (0x1UL << RCC_APB2ENR_IOPAEN_Pos) /*!< 0x00000004 */ +#define RCC_APB2ENR_IOPAEN RCC_APB2ENR_IOPAEN_Msk /*!< I/O port A clock enable */ +#define RCC_APB2ENR_IOPBEN_Pos (3U) +#define RCC_APB2ENR_IOPBEN_Msk (0x1UL << RCC_APB2ENR_IOPBEN_Pos) /*!< 0x00000008 */ +#define RCC_APB2ENR_IOPBEN RCC_APB2ENR_IOPBEN_Msk /*!< I/O port B clock enable */ +#define RCC_APB2ENR_IOPCEN_Pos (4U) +#define RCC_APB2ENR_IOPCEN_Msk (0x1UL << RCC_APB2ENR_IOPCEN_Pos) /*!< 0x00000010 */ +#define RCC_APB2ENR_IOPCEN RCC_APB2ENR_IOPCEN_Msk /*!< I/O port C clock enable */ +#define RCC_APB2ENR_IOPDEN_Pos (5U) +#define RCC_APB2ENR_IOPDEN_Msk (0x1UL << RCC_APB2ENR_IOPDEN_Pos) /*!< 0x00000020 */ +#define RCC_APB2ENR_IOPDEN RCC_APB2ENR_IOPDEN_Msk /*!< I/O port D clock enable */ +#define RCC_APB2ENR_ADC1EN_Pos (9U) +#define RCC_APB2ENR_ADC1EN_Msk (0x1UL << RCC_APB2ENR_ADC1EN_Pos) /*!< 0x00000200 */ +#define RCC_APB2ENR_ADC1EN RCC_APB2ENR_ADC1EN_Msk /*!< ADC 1 interface clock enable */ + +#define RCC_APB2ENR_ADC2EN_Pos (10U) +#define RCC_APB2ENR_ADC2EN_Msk (0x1UL << RCC_APB2ENR_ADC2EN_Pos) /*!< 0x00000400 */ +#define RCC_APB2ENR_ADC2EN RCC_APB2ENR_ADC2EN_Msk /*!< ADC 2 interface clock enable */ + +#define RCC_APB2ENR_TIM1EN_Pos (11U) +#define RCC_APB2ENR_TIM1EN_Msk (0x1UL << RCC_APB2ENR_TIM1EN_Pos) /*!< 0x00000800 */ +#define RCC_APB2ENR_TIM1EN RCC_APB2ENR_TIM1EN_Msk /*!< TIM1 Timer clock enable */ +#define RCC_APB2ENR_SPI1EN_Pos (12U) +#define RCC_APB2ENR_SPI1EN_Msk (0x1UL << RCC_APB2ENR_SPI1EN_Pos) /*!< 0x00001000 */ +#define RCC_APB2ENR_SPI1EN RCC_APB2ENR_SPI1EN_Msk /*!< SPI 1 clock enable */ +#define RCC_APB2ENR_USART1EN_Pos (14U) +#define RCC_APB2ENR_USART1EN_Msk (0x1UL << RCC_APB2ENR_USART1EN_Pos) /*!< 0x00004000 */ +#define RCC_APB2ENR_USART1EN RCC_APB2ENR_USART1EN_Msk /*!< USART1 clock enable */ + + + + + + +/***************** Bit definition for RCC_APB1ENR register ******************/ +#define RCC_APB1ENR_TIM2EN_Pos (0U) +#define RCC_APB1ENR_TIM2EN_Msk (0x1UL << RCC_APB1ENR_TIM2EN_Pos) /*!< 0x00000001 */ +#define RCC_APB1ENR_TIM2EN RCC_APB1ENR_TIM2EN_Msk /*!< Timer 2 clock enabled*/ +#define RCC_APB1ENR_TIM3EN_Pos (1U) +#define RCC_APB1ENR_TIM3EN_Msk (0x1UL << RCC_APB1ENR_TIM3EN_Pos) /*!< 0x00000002 */ +#define RCC_APB1ENR_TIM3EN RCC_APB1ENR_TIM3EN_Msk /*!< Timer 3 clock enable */ +#define RCC_APB1ENR_WWDGEN_Pos (11U) +#define RCC_APB1ENR_WWDGEN_Msk (0x1UL << RCC_APB1ENR_WWDGEN_Pos) /*!< 0x00000800 */ +#define RCC_APB1ENR_WWDGEN RCC_APB1ENR_WWDGEN_Msk /*!< Window Watchdog clock enable */ +#define RCC_APB1ENR_USART2EN_Pos (17U) +#define RCC_APB1ENR_USART2EN_Msk (0x1UL << RCC_APB1ENR_USART2EN_Pos) /*!< 0x00020000 */ +#define RCC_APB1ENR_USART2EN RCC_APB1ENR_USART2EN_Msk /*!< USART 2 clock enable */ +#define RCC_APB1ENR_I2C1EN_Pos (21U) +#define RCC_APB1ENR_I2C1EN_Msk (0x1UL << RCC_APB1ENR_I2C1EN_Pos) /*!< 0x00200000 */ +#define RCC_APB1ENR_I2C1EN RCC_APB1ENR_I2C1EN_Msk /*!< I2C 1 clock enable */ + +#define RCC_APB1ENR_CAN1EN_Pos (25U) +#define RCC_APB1ENR_CAN1EN_Msk (0x1UL << RCC_APB1ENR_CAN1EN_Pos) /*!< 0x02000000 */ +#define RCC_APB1ENR_CAN1EN RCC_APB1ENR_CAN1EN_Msk /*!< CAN1 clock enable */ + +#define RCC_APB1ENR_BKPEN_Pos (27U) +#define RCC_APB1ENR_BKPEN_Msk (0x1UL << RCC_APB1ENR_BKPEN_Pos) /*!< 0x08000000 */ +#define RCC_APB1ENR_BKPEN RCC_APB1ENR_BKPEN_Msk /*!< Backup interface clock enable */ +#define RCC_APB1ENR_PWREN_Pos (28U) +#define RCC_APB1ENR_PWREN_Msk (0x1UL << RCC_APB1ENR_PWREN_Pos) /*!< 0x10000000 */ +#define RCC_APB1ENR_PWREN RCC_APB1ENR_PWREN_Msk /*!< Power interface clock enable */ + + +#define RCC_APB1ENR_USBEN_Pos (23U) +#define RCC_APB1ENR_USBEN_Msk (0x1UL << RCC_APB1ENR_USBEN_Pos) /*!< 0x00800000 */ +#define RCC_APB1ENR_USBEN RCC_APB1ENR_USBEN_Msk /*!< USB Device clock enable */ + + + + + + +/******************* Bit definition for RCC_BDCR register *******************/ +#define RCC_BDCR_LSEON_Pos (0U) +#define RCC_BDCR_LSEON_Msk (0x1UL << RCC_BDCR_LSEON_Pos) /*!< 0x00000001 */ +#define RCC_BDCR_LSEON RCC_BDCR_LSEON_Msk /*!< External Low Speed oscillator enable */ +#define RCC_BDCR_LSERDY_Pos (1U) +#define RCC_BDCR_LSERDY_Msk (0x1UL << RCC_BDCR_LSERDY_Pos) /*!< 0x00000002 */ +#define RCC_BDCR_LSERDY RCC_BDCR_LSERDY_Msk /*!< External Low Speed oscillator Ready */ +#define RCC_BDCR_LSEBYP_Pos (2U) +#define RCC_BDCR_LSEBYP_Msk (0x1UL << RCC_BDCR_LSEBYP_Pos) /*!< 0x00000004 */ +#define RCC_BDCR_LSEBYP RCC_BDCR_LSEBYP_Msk /*!< External Low Speed oscillator Bypass */ + +#define RCC_BDCR_RTCSEL_Pos (8U) +#define RCC_BDCR_RTCSEL_Msk (0x3UL << RCC_BDCR_RTCSEL_Pos) /*!< 0x00000300 */ +#define RCC_BDCR_RTCSEL RCC_BDCR_RTCSEL_Msk /*!< RTCSEL[1:0] bits (RTC clock source selection) */ +#define RCC_BDCR_RTCSEL_0 (0x1UL << RCC_BDCR_RTCSEL_Pos) /*!< 0x00000100 */ +#define RCC_BDCR_RTCSEL_1 (0x2UL << RCC_BDCR_RTCSEL_Pos) /*!< 0x00000200 */ + +/*!< RTC congiguration */ +#define RCC_BDCR_RTCSEL_NOCLOCK 0x00000000U /*!< No clock */ +#define RCC_BDCR_RTCSEL_LSE 0x00000100U /*!< LSE oscillator clock used as RTC clock */ +#define RCC_BDCR_RTCSEL_LSI 0x00000200U /*!< LSI oscillator clock used as RTC clock */ +#define RCC_BDCR_RTCSEL_HSE 0x00000300U /*!< HSE oscillator clock divided by 128 used as RTC clock */ + +#define RCC_BDCR_RTCEN_Pos (15U) +#define RCC_BDCR_RTCEN_Msk (0x1UL << RCC_BDCR_RTCEN_Pos) /*!< 0x00008000 */ +#define RCC_BDCR_RTCEN RCC_BDCR_RTCEN_Msk /*!< RTC clock enable */ +#define RCC_BDCR_BDRST_Pos (16U) +#define RCC_BDCR_BDRST_Msk (0x1UL << RCC_BDCR_BDRST_Pos) /*!< 0x00010000 */ +#define RCC_BDCR_BDRST RCC_BDCR_BDRST_Msk /*!< Backup domain software reset */ + +/******************* Bit definition for RCC_CSR register ********************/ +#define RCC_CSR_LSION_Pos (0U) +#define RCC_CSR_LSION_Msk (0x1UL << RCC_CSR_LSION_Pos) /*!< 0x00000001 */ +#define RCC_CSR_LSION RCC_CSR_LSION_Msk /*!< Internal Low Speed oscillator enable */ +#define RCC_CSR_LSIRDY_Pos (1U) +#define RCC_CSR_LSIRDY_Msk (0x1UL << RCC_CSR_LSIRDY_Pos) /*!< 0x00000002 */ +#define RCC_CSR_LSIRDY RCC_CSR_LSIRDY_Msk /*!< Internal Low Speed oscillator Ready */ +#define RCC_CSR_RMVF_Pos (24U) +#define RCC_CSR_RMVF_Msk (0x1UL << RCC_CSR_RMVF_Pos) /*!< 0x01000000 */ +#define RCC_CSR_RMVF RCC_CSR_RMVF_Msk /*!< Remove reset flag */ +#define RCC_CSR_PINRSTF_Pos (26U) +#define RCC_CSR_PINRSTF_Msk (0x1UL << RCC_CSR_PINRSTF_Pos) /*!< 0x04000000 */ +#define RCC_CSR_PINRSTF RCC_CSR_PINRSTF_Msk /*!< PIN reset flag */ +#define RCC_CSR_PORRSTF_Pos (27U) +#define RCC_CSR_PORRSTF_Msk (0x1UL << RCC_CSR_PORRSTF_Pos) /*!< 0x08000000 */ +#define RCC_CSR_PORRSTF RCC_CSR_PORRSTF_Msk /*!< POR/PDR reset flag */ +#define RCC_CSR_SFTRSTF_Pos (28U) +#define RCC_CSR_SFTRSTF_Msk (0x1UL << RCC_CSR_SFTRSTF_Pos) /*!< 0x10000000 */ +#define RCC_CSR_SFTRSTF RCC_CSR_SFTRSTF_Msk /*!< Software Reset flag */ +#define RCC_CSR_IWDGRSTF_Pos (29U) +#define RCC_CSR_IWDGRSTF_Msk (0x1UL << RCC_CSR_IWDGRSTF_Pos) /*!< 0x20000000 */ +#define RCC_CSR_IWDGRSTF RCC_CSR_IWDGRSTF_Msk /*!< Independent Watchdog reset flag */ +#define RCC_CSR_WWDGRSTF_Pos (30U) +#define RCC_CSR_WWDGRSTF_Msk (0x1UL << RCC_CSR_WWDGRSTF_Pos) /*!< 0x40000000 */ +#define RCC_CSR_WWDGRSTF RCC_CSR_WWDGRSTF_Msk /*!< Window watchdog reset flag */ +#define RCC_CSR_LPWRRSTF_Pos (31U) +#define RCC_CSR_LPWRRSTF_Msk (0x1UL << RCC_CSR_LPWRRSTF_Pos) /*!< 0x80000000 */ +#define RCC_CSR_LPWRRSTF RCC_CSR_LPWRRSTF_Msk /*!< Low-Power reset flag */ + + + +/******************************************************************************/ +/* */ +/* General Purpose and Alternate Function I/O */ +/* */ +/******************************************************************************/ + +/******************* Bit definition for GPIO_CRL register *******************/ +#define GPIO_CRL_MODE_Pos (0U) +#define GPIO_CRL_MODE_Msk (0x33333333UL << GPIO_CRL_MODE_Pos) /*!< 0x33333333 */ +#define GPIO_CRL_MODE GPIO_CRL_MODE_Msk /*!< Port x mode bits */ + +#define GPIO_CRL_MODE0_Pos (0U) +#define GPIO_CRL_MODE0_Msk (0x3UL << GPIO_CRL_MODE0_Pos) /*!< 0x00000003 */ +#define GPIO_CRL_MODE0 GPIO_CRL_MODE0_Msk /*!< MODE0[1:0] bits (Port x mode bits, pin 0) */ +#define GPIO_CRL_MODE0_0 (0x1UL << GPIO_CRL_MODE0_Pos) /*!< 0x00000001 */ +#define GPIO_CRL_MODE0_1 (0x2UL << GPIO_CRL_MODE0_Pos) /*!< 0x00000002 */ + +#define GPIO_CRL_MODE1_Pos (4U) +#define GPIO_CRL_MODE1_Msk (0x3UL << GPIO_CRL_MODE1_Pos) /*!< 0x00000030 */ +#define GPIO_CRL_MODE1 GPIO_CRL_MODE1_Msk /*!< MODE1[1:0] bits (Port x mode bits, pin 1) */ +#define GPIO_CRL_MODE1_0 (0x1UL << GPIO_CRL_MODE1_Pos) /*!< 0x00000010 */ +#define GPIO_CRL_MODE1_1 (0x2UL << GPIO_CRL_MODE1_Pos) /*!< 0x00000020 */ + +#define GPIO_CRL_MODE2_Pos (8U) +#define GPIO_CRL_MODE2_Msk (0x3UL << GPIO_CRL_MODE2_Pos) /*!< 0x00000300 */ +#define GPIO_CRL_MODE2 GPIO_CRL_MODE2_Msk /*!< MODE2[1:0] bits (Port x mode bits, pin 2) */ +#define GPIO_CRL_MODE2_0 (0x1UL << GPIO_CRL_MODE2_Pos) /*!< 0x00000100 */ +#define GPIO_CRL_MODE2_1 (0x2UL << GPIO_CRL_MODE2_Pos) /*!< 0x00000200 */ + +#define GPIO_CRL_MODE3_Pos (12U) +#define GPIO_CRL_MODE3_Msk (0x3UL << GPIO_CRL_MODE3_Pos) /*!< 0x00003000 */ +#define GPIO_CRL_MODE3 GPIO_CRL_MODE3_Msk /*!< MODE3[1:0] bits (Port x mode bits, pin 3) */ +#define GPIO_CRL_MODE3_0 (0x1UL << GPIO_CRL_MODE3_Pos) /*!< 0x00001000 */ +#define GPIO_CRL_MODE3_1 (0x2UL << GPIO_CRL_MODE3_Pos) /*!< 0x00002000 */ + +#define GPIO_CRL_MODE4_Pos (16U) +#define GPIO_CRL_MODE4_Msk (0x3UL << GPIO_CRL_MODE4_Pos) /*!< 0x00030000 */ +#define GPIO_CRL_MODE4 GPIO_CRL_MODE4_Msk /*!< MODE4[1:0] bits (Port x mode bits, pin 4) */ +#define GPIO_CRL_MODE4_0 (0x1UL << GPIO_CRL_MODE4_Pos) /*!< 0x00010000 */ +#define GPIO_CRL_MODE4_1 (0x2UL << GPIO_CRL_MODE4_Pos) /*!< 0x00020000 */ + +#define GPIO_CRL_MODE5_Pos (20U) +#define GPIO_CRL_MODE5_Msk (0x3UL << GPIO_CRL_MODE5_Pos) /*!< 0x00300000 */ +#define GPIO_CRL_MODE5 GPIO_CRL_MODE5_Msk /*!< MODE5[1:0] bits (Port x mode bits, pin 5) */ +#define GPIO_CRL_MODE5_0 (0x1UL << GPIO_CRL_MODE5_Pos) /*!< 0x00100000 */ +#define GPIO_CRL_MODE5_1 (0x2UL << GPIO_CRL_MODE5_Pos) /*!< 0x00200000 */ + +#define GPIO_CRL_MODE6_Pos (24U) +#define GPIO_CRL_MODE6_Msk (0x3UL << GPIO_CRL_MODE6_Pos) /*!< 0x03000000 */ +#define GPIO_CRL_MODE6 GPIO_CRL_MODE6_Msk /*!< MODE6[1:0] bits (Port x mode bits, pin 6) */ +#define GPIO_CRL_MODE6_0 (0x1UL << GPIO_CRL_MODE6_Pos) /*!< 0x01000000 */ +#define GPIO_CRL_MODE6_1 (0x2UL << GPIO_CRL_MODE6_Pos) /*!< 0x02000000 */ + +#define GPIO_CRL_MODE7_Pos (28U) +#define GPIO_CRL_MODE7_Msk (0x3UL << GPIO_CRL_MODE7_Pos) /*!< 0x30000000 */ +#define GPIO_CRL_MODE7 GPIO_CRL_MODE7_Msk /*!< MODE7[1:0] bits (Port x mode bits, pin 7) */ +#define GPIO_CRL_MODE7_0 (0x1UL << GPIO_CRL_MODE7_Pos) /*!< 0x10000000 */ +#define GPIO_CRL_MODE7_1 (0x2UL << GPIO_CRL_MODE7_Pos) /*!< 0x20000000 */ + +#define GPIO_CRL_CNF_Pos (2U) +#define GPIO_CRL_CNF_Msk (0x33333333UL << GPIO_CRL_CNF_Pos) /*!< 0xCCCCCCCC */ +#define GPIO_CRL_CNF GPIO_CRL_CNF_Msk /*!< Port x configuration bits */ + +#define GPIO_CRL_CNF0_Pos (2U) +#define GPIO_CRL_CNF0_Msk (0x3UL << GPIO_CRL_CNF0_Pos) /*!< 0x0000000C */ +#define GPIO_CRL_CNF0 GPIO_CRL_CNF0_Msk /*!< CNF0[1:0] bits (Port x configuration bits, pin 0) */ +#define GPIO_CRL_CNF0_0 (0x1UL << GPIO_CRL_CNF0_Pos) /*!< 0x00000004 */ +#define GPIO_CRL_CNF0_1 (0x2UL << GPIO_CRL_CNF0_Pos) /*!< 0x00000008 */ + +#define GPIO_CRL_CNF1_Pos (6U) +#define GPIO_CRL_CNF1_Msk (0x3UL << GPIO_CRL_CNF1_Pos) /*!< 0x000000C0 */ +#define GPIO_CRL_CNF1 GPIO_CRL_CNF1_Msk /*!< CNF1[1:0] bits (Port x configuration bits, pin 1) */ +#define GPIO_CRL_CNF1_0 (0x1UL << GPIO_CRL_CNF1_Pos) /*!< 0x00000040 */ +#define GPIO_CRL_CNF1_1 (0x2UL << GPIO_CRL_CNF1_Pos) /*!< 0x00000080 */ + +#define GPIO_CRL_CNF2_Pos (10U) +#define GPIO_CRL_CNF2_Msk (0x3UL << GPIO_CRL_CNF2_Pos) /*!< 0x00000C00 */ +#define GPIO_CRL_CNF2 GPIO_CRL_CNF2_Msk /*!< CNF2[1:0] bits (Port x configuration bits, pin 2) */ +#define GPIO_CRL_CNF2_0 (0x1UL << GPIO_CRL_CNF2_Pos) /*!< 0x00000400 */ +#define GPIO_CRL_CNF2_1 (0x2UL << GPIO_CRL_CNF2_Pos) /*!< 0x00000800 */ + +#define GPIO_CRL_CNF3_Pos (14U) +#define GPIO_CRL_CNF3_Msk (0x3UL << GPIO_CRL_CNF3_Pos) /*!< 0x0000C000 */ +#define GPIO_CRL_CNF3 GPIO_CRL_CNF3_Msk /*!< CNF3[1:0] bits (Port x configuration bits, pin 3) */ +#define GPIO_CRL_CNF3_0 (0x1UL << GPIO_CRL_CNF3_Pos) /*!< 0x00004000 */ +#define GPIO_CRL_CNF3_1 (0x2UL << GPIO_CRL_CNF3_Pos) /*!< 0x00008000 */ + +#define GPIO_CRL_CNF4_Pos (18U) +#define GPIO_CRL_CNF4_Msk (0x3UL << GPIO_CRL_CNF4_Pos) /*!< 0x000C0000 */ +#define GPIO_CRL_CNF4 GPIO_CRL_CNF4_Msk /*!< CNF4[1:0] bits (Port x configuration bits, pin 4) */ +#define GPIO_CRL_CNF4_0 (0x1UL << GPIO_CRL_CNF4_Pos) /*!< 0x00040000 */ +#define GPIO_CRL_CNF4_1 (0x2UL << GPIO_CRL_CNF4_Pos) /*!< 0x00080000 */ + +#define GPIO_CRL_CNF5_Pos (22U) +#define GPIO_CRL_CNF5_Msk (0x3UL << GPIO_CRL_CNF5_Pos) /*!< 0x00C00000 */ +#define GPIO_CRL_CNF5 GPIO_CRL_CNF5_Msk /*!< CNF5[1:0] bits (Port x configuration bits, pin 5) */ +#define GPIO_CRL_CNF5_0 (0x1UL << GPIO_CRL_CNF5_Pos) /*!< 0x00400000 */ +#define GPIO_CRL_CNF5_1 (0x2UL << GPIO_CRL_CNF5_Pos) /*!< 0x00800000 */ + +#define GPIO_CRL_CNF6_Pos (26U) +#define GPIO_CRL_CNF6_Msk (0x3UL << GPIO_CRL_CNF6_Pos) /*!< 0x0C000000 */ +#define GPIO_CRL_CNF6 GPIO_CRL_CNF6_Msk /*!< CNF6[1:0] bits (Port x configuration bits, pin 6) */ +#define GPIO_CRL_CNF6_0 (0x1UL << GPIO_CRL_CNF6_Pos) /*!< 0x04000000 */ +#define GPIO_CRL_CNF6_1 (0x2UL << GPIO_CRL_CNF6_Pos) /*!< 0x08000000 */ + +#define GPIO_CRL_CNF7_Pos (30U) +#define GPIO_CRL_CNF7_Msk (0x3UL << GPIO_CRL_CNF7_Pos) /*!< 0xC0000000 */ +#define GPIO_CRL_CNF7 GPIO_CRL_CNF7_Msk /*!< CNF7[1:0] bits (Port x configuration bits, pin 7) */ +#define GPIO_CRL_CNF7_0 (0x1UL << GPIO_CRL_CNF7_Pos) /*!< 0x40000000 */ +#define GPIO_CRL_CNF7_1 (0x2UL << GPIO_CRL_CNF7_Pos) /*!< 0x80000000 */ + +/******************* Bit definition for GPIO_CRH register *******************/ +#define GPIO_CRH_MODE_Pos (0U) +#define GPIO_CRH_MODE_Msk (0x33333333UL << GPIO_CRH_MODE_Pos) /*!< 0x33333333 */ +#define GPIO_CRH_MODE GPIO_CRH_MODE_Msk /*!< Port x mode bits */ + +#define GPIO_CRH_MODE8_Pos (0U) +#define GPIO_CRH_MODE8_Msk (0x3UL << GPIO_CRH_MODE8_Pos) /*!< 0x00000003 */ +#define GPIO_CRH_MODE8 GPIO_CRH_MODE8_Msk /*!< MODE8[1:0] bits (Port x mode bits, pin 8) */ +#define GPIO_CRH_MODE8_0 (0x1UL << GPIO_CRH_MODE8_Pos) /*!< 0x00000001 */ +#define GPIO_CRH_MODE8_1 (0x2UL << GPIO_CRH_MODE8_Pos) /*!< 0x00000002 */ + +#define GPIO_CRH_MODE9_Pos (4U) +#define GPIO_CRH_MODE9_Msk (0x3UL << GPIO_CRH_MODE9_Pos) /*!< 0x00000030 */ +#define GPIO_CRH_MODE9 GPIO_CRH_MODE9_Msk /*!< MODE9[1:0] bits (Port x mode bits, pin 9) */ +#define GPIO_CRH_MODE9_0 (0x1UL << GPIO_CRH_MODE9_Pos) /*!< 0x00000010 */ +#define GPIO_CRH_MODE9_1 (0x2UL << GPIO_CRH_MODE9_Pos) /*!< 0x00000020 */ + +#define GPIO_CRH_MODE10_Pos (8U) +#define GPIO_CRH_MODE10_Msk (0x3UL << GPIO_CRH_MODE10_Pos) /*!< 0x00000300 */ +#define GPIO_CRH_MODE10 GPIO_CRH_MODE10_Msk /*!< MODE10[1:0] bits (Port x mode bits, pin 10) */ +#define GPIO_CRH_MODE10_0 (0x1UL << GPIO_CRH_MODE10_Pos) /*!< 0x00000100 */ +#define GPIO_CRH_MODE10_1 (0x2UL << GPIO_CRH_MODE10_Pos) /*!< 0x00000200 */ + +#define GPIO_CRH_MODE11_Pos (12U) +#define GPIO_CRH_MODE11_Msk (0x3UL << GPIO_CRH_MODE11_Pos) /*!< 0x00003000 */ +#define GPIO_CRH_MODE11 GPIO_CRH_MODE11_Msk /*!< MODE11[1:0] bits (Port x mode bits, pin 11) */ +#define GPIO_CRH_MODE11_0 (0x1UL << GPIO_CRH_MODE11_Pos) /*!< 0x00001000 */ +#define GPIO_CRH_MODE11_1 (0x2UL << GPIO_CRH_MODE11_Pos) /*!< 0x00002000 */ + +#define GPIO_CRH_MODE12_Pos (16U) +#define GPIO_CRH_MODE12_Msk (0x3UL << GPIO_CRH_MODE12_Pos) /*!< 0x00030000 */ +#define GPIO_CRH_MODE12 GPIO_CRH_MODE12_Msk /*!< MODE12[1:0] bits (Port x mode bits, pin 12) */ +#define GPIO_CRH_MODE12_0 (0x1UL << GPIO_CRH_MODE12_Pos) /*!< 0x00010000 */ +#define GPIO_CRH_MODE12_1 (0x2UL << GPIO_CRH_MODE12_Pos) /*!< 0x00020000 */ + +#define GPIO_CRH_MODE13_Pos (20U) +#define GPIO_CRH_MODE13_Msk (0x3UL << GPIO_CRH_MODE13_Pos) /*!< 0x00300000 */ +#define GPIO_CRH_MODE13 GPIO_CRH_MODE13_Msk /*!< MODE13[1:0] bits (Port x mode bits, pin 13) */ +#define GPIO_CRH_MODE13_0 (0x1UL << GPIO_CRH_MODE13_Pos) /*!< 0x00100000 */ +#define GPIO_CRH_MODE13_1 (0x2UL << GPIO_CRH_MODE13_Pos) /*!< 0x00200000 */ + +#define GPIO_CRH_MODE14_Pos (24U) +#define GPIO_CRH_MODE14_Msk (0x3UL << GPIO_CRH_MODE14_Pos) /*!< 0x03000000 */ +#define GPIO_CRH_MODE14 GPIO_CRH_MODE14_Msk /*!< MODE14[1:0] bits (Port x mode bits, pin 14) */ +#define GPIO_CRH_MODE14_0 (0x1UL << GPIO_CRH_MODE14_Pos) /*!< 0x01000000 */ +#define GPIO_CRH_MODE14_1 (0x2UL << GPIO_CRH_MODE14_Pos) /*!< 0x02000000 */ + +#define GPIO_CRH_MODE15_Pos (28U) +#define GPIO_CRH_MODE15_Msk (0x3UL << GPIO_CRH_MODE15_Pos) /*!< 0x30000000 */ +#define GPIO_CRH_MODE15 GPIO_CRH_MODE15_Msk /*!< MODE15[1:0] bits (Port x mode bits, pin 15) */ +#define GPIO_CRH_MODE15_0 (0x1UL << GPIO_CRH_MODE15_Pos) /*!< 0x10000000 */ +#define GPIO_CRH_MODE15_1 (0x2UL << GPIO_CRH_MODE15_Pos) /*!< 0x20000000 */ + +#define GPIO_CRH_CNF_Pos (2U) +#define GPIO_CRH_CNF_Msk (0x33333333UL << GPIO_CRH_CNF_Pos) /*!< 0xCCCCCCCC */ +#define GPIO_CRH_CNF GPIO_CRH_CNF_Msk /*!< Port x configuration bits */ + +#define GPIO_CRH_CNF8_Pos (2U) +#define GPIO_CRH_CNF8_Msk (0x3UL << GPIO_CRH_CNF8_Pos) /*!< 0x0000000C */ +#define GPIO_CRH_CNF8 GPIO_CRH_CNF8_Msk /*!< CNF8[1:0] bits (Port x configuration bits, pin 8) */ +#define GPIO_CRH_CNF8_0 (0x1UL << GPIO_CRH_CNF8_Pos) /*!< 0x00000004 */ +#define GPIO_CRH_CNF8_1 (0x2UL << GPIO_CRH_CNF8_Pos) /*!< 0x00000008 */ + +#define GPIO_CRH_CNF9_Pos (6U) +#define GPIO_CRH_CNF9_Msk (0x3UL << GPIO_CRH_CNF9_Pos) /*!< 0x000000C0 */ +#define GPIO_CRH_CNF9 GPIO_CRH_CNF9_Msk /*!< CNF9[1:0] bits (Port x configuration bits, pin 9) */ +#define GPIO_CRH_CNF9_0 (0x1UL << GPIO_CRH_CNF9_Pos) /*!< 0x00000040 */ +#define GPIO_CRH_CNF9_1 (0x2UL << GPIO_CRH_CNF9_Pos) /*!< 0x00000080 */ + +#define GPIO_CRH_CNF10_Pos (10U) +#define GPIO_CRH_CNF10_Msk (0x3UL << GPIO_CRH_CNF10_Pos) /*!< 0x00000C00 */ +#define GPIO_CRH_CNF10 GPIO_CRH_CNF10_Msk /*!< CNF10[1:0] bits (Port x configuration bits, pin 10) */ +#define GPIO_CRH_CNF10_0 (0x1UL << GPIO_CRH_CNF10_Pos) /*!< 0x00000400 */ +#define GPIO_CRH_CNF10_1 (0x2UL << GPIO_CRH_CNF10_Pos) /*!< 0x00000800 */ + +#define GPIO_CRH_CNF11_Pos (14U) +#define GPIO_CRH_CNF11_Msk (0x3UL << GPIO_CRH_CNF11_Pos) /*!< 0x0000C000 */ +#define GPIO_CRH_CNF11 GPIO_CRH_CNF11_Msk /*!< CNF11[1:0] bits (Port x configuration bits, pin 11) */ +#define GPIO_CRH_CNF11_0 (0x1UL << GPIO_CRH_CNF11_Pos) /*!< 0x00004000 */ +#define GPIO_CRH_CNF11_1 (0x2UL << GPIO_CRH_CNF11_Pos) /*!< 0x00008000 */ + +#define GPIO_CRH_CNF12_Pos (18U) +#define GPIO_CRH_CNF12_Msk (0x3UL << GPIO_CRH_CNF12_Pos) /*!< 0x000C0000 */ +#define GPIO_CRH_CNF12 GPIO_CRH_CNF12_Msk /*!< CNF12[1:0] bits (Port x configuration bits, pin 12) */ +#define GPIO_CRH_CNF12_0 (0x1UL << GPIO_CRH_CNF12_Pos) /*!< 0x00040000 */ +#define GPIO_CRH_CNF12_1 (0x2UL << GPIO_CRH_CNF12_Pos) /*!< 0x00080000 */ + +#define GPIO_CRH_CNF13_Pos (22U) +#define GPIO_CRH_CNF13_Msk (0x3UL << GPIO_CRH_CNF13_Pos) /*!< 0x00C00000 */ +#define GPIO_CRH_CNF13 GPIO_CRH_CNF13_Msk /*!< CNF13[1:0] bits (Port x configuration bits, pin 13) */ +#define GPIO_CRH_CNF13_0 (0x1UL << GPIO_CRH_CNF13_Pos) /*!< 0x00400000 */ +#define GPIO_CRH_CNF13_1 (0x2UL << GPIO_CRH_CNF13_Pos) /*!< 0x00800000 */ + +#define GPIO_CRH_CNF14_Pos (26U) +#define GPIO_CRH_CNF14_Msk (0x3UL << GPIO_CRH_CNF14_Pos) /*!< 0x0C000000 */ +#define GPIO_CRH_CNF14 GPIO_CRH_CNF14_Msk /*!< CNF14[1:0] bits (Port x configuration bits, pin 14) */ +#define GPIO_CRH_CNF14_0 (0x1UL << GPIO_CRH_CNF14_Pos) /*!< 0x04000000 */ +#define GPIO_CRH_CNF14_1 (0x2UL << GPIO_CRH_CNF14_Pos) /*!< 0x08000000 */ + +#define GPIO_CRH_CNF15_Pos (30U) +#define GPIO_CRH_CNF15_Msk (0x3UL << GPIO_CRH_CNF15_Pos) /*!< 0xC0000000 */ +#define GPIO_CRH_CNF15 GPIO_CRH_CNF15_Msk /*!< CNF15[1:0] bits (Port x configuration bits, pin 15) */ +#define GPIO_CRH_CNF15_0 (0x1UL << GPIO_CRH_CNF15_Pos) /*!< 0x40000000 */ +#define GPIO_CRH_CNF15_1 (0x2UL << GPIO_CRH_CNF15_Pos) /*!< 0x80000000 */ + +/*!<****************** Bit definition for GPIO_IDR register *******************/ +#define GPIO_IDR_IDR0_Pos (0U) +#define GPIO_IDR_IDR0_Msk (0x1UL << GPIO_IDR_IDR0_Pos) /*!< 0x00000001 */ +#define GPIO_IDR_IDR0 GPIO_IDR_IDR0_Msk /*!< Port input data, bit 0 */ +#define GPIO_IDR_IDR1_Pos (1U) +#define GPIO_IDR_IDR1_Msk (0x1UL << GPIO_IDR_IDR1_Pos) /*!< 0x00000002 */ +#define GPIO_IDR_IDR1 GPIO_IDR_IDR1_Msk /*!< Port input data, bit 1 */ +#define GPIO_IDR_IDR2_Pos (2U) +#define GPIO_IDR_IDR2_Msk (0x1UL << GPIO_IDR_IDR2_Pos) /*!< 0x00000004 */ +#define GPIO_IDR_IDR2 GPIO_IDR_IDR2_Msk /*!< Port input data, bit 2 */ +#define GPIO_IDR_IDR3_Pos (3U) +#define GPIO_IDR_IDR3_Msk (0x1UL << GPIO_IDR_IDR3_Pos) /*!< 0x00000008 */ +#define GPIO_IDR_IDR3 GPIO_IDR_IDR3_Msk /*!< Port input data, bit 3 */ +#define GPIO_IDR_IDR4_Pos (4U) +#define GPIO_IDR_IDR4_Msk (0x1UL << GPIO_IDR_IDR4_Pos) /*!< 0x00000010 */ +#define GPIO_IDR_IDR4 GPIO_IDR_IDR4_Msk /*!< Port input data, bit 4 */ +#define GPIO_IDR_IDR5_Pos (5U) +#define GPIO_IDR_IDR5_Msk (0x1UL << GPIO_IDR_IDR5_Pos) /*!< 0x00000020 */ +#define GPIO_IDR_IDR5 GPIO_IDR_IDR5_Msk /*!< Port input data, bit 5 */ +#define GPIO_IDR_IDR6_Pos (6U) +#define GPIO_IDR_IDR6_Msk (0x1UL << GPIO_IDR_IDR6_Pos) /*!< 0x00000040 */ +#define GPIO_IDR_IDR6 GPIO_IDR_IDR6_Msk /*!< Port input data, bit 6 */ +#define GPIO_IDR_IDR7_Pos (7U) +#define GPIO_IDR_IDR7_Msk (0x1UL << GPIO_IDR_IDR7_Pos) /*!< 0x00000080 */ +#define GPIO_IDR_IDR7 GPIO_IDR_IDR7_Msk /*!< Port input data, bit 7 */ +#define GPIO_IDR_IDR8_Pos (8U) +#define GPIO_IDR_IDR8_Msk (0x1UL << GPIO_IDR_IDR8_Pos) /*!< 0x00000100 */ +#define GPIO_IDR_IDR8 GPIO_IDR_IDR8_Msk /*!< Port input data, bit 8 */ +#define GPIO_IDR_IDR9_Pos (9U) +#define GPIO_IDR_IDR9_Msk (0x1UL << GPIO_IDR_IDR9_Pos) /*!< 0x00000200 */ +#define GPIO_IDR_IDR9 GPIO_IDR_IDR9_Msk /*!< Port input data, bit 9 */ +#define GPIO_IDR_IDR10_Pos (10U) +#define GPIO_IDR_IDR10_Msk (0x1UL << GPIO_IDR_IDR10_Pos) /*!< 0x00000400 */ +#define GPIO_IDR_IDR10 GPIO_IDR_IDR10_Msk /*!< Port input data, bit 10 */ +#define GPIO_IDR_IDR11_Pos (11U) +#define GPIO_IDR_IDR11_Msk (0x1UL << GPIO_IDR_IDR11_Pos) /*!< 0x00000800 */ +#define GPIO_IDR_IDR11 GPIO_IDR_IDR11_Msk /*!< Port input data, bit 11 */ +#define GPIO_IDR_IDR12_Pos (12U) +#define GPIO_IDR_IDR12_Msk (0x1UL << GPIO_IDR_IDR12_Pos) /*!< 0x00001000 */ +#define GPIO_IDR_IDR12 GPIO_IDR_IDR12_Msk /*!< Port input data, bit 12 */ +#define GPIO_IDR_IDR13_Pos (13U) +#define GPIO_IDR_IDR13_Msk (0x1UL << GPIO_IDR_IDR13_Pos) /*!< 0x00002000 */ +#define GPIO_IDR_IDR13 GPIO_IDR_IDR13_Msk /*!< Port input data, bit 13 */ +#define GPIO_IDR_IDR14_Pos (14U) +#define GPIO_IDR_IDR14_Msk (0x1UL << GPIO_IDR_IDR14_Pos) /*!< 0x00004000 */ +#define GPIO_IDR_IDR14 GPIO_IDR_IDR14_Msk /*!< Port input data, bit 14 */ +#define GPIO_IDR_IDR15_Pos (15U) +#define GPIO_IDR_IDR15_Msk (0x1UL << GPIO_IDR_IDR15_Pos) /*!< 0x00008000 */ +#define GPIO_IDR_IDR15 GPIO_IDR_IDR15_Msk /*!< Port input data, bit 15 */ + +/******************* Bit definition for GPIO_ODR register *******************/ +#define GPIO_ODR_ODR0_Pos (0U) +#define GPIO_ODR_ODR0_Msk (0x1UL << GPIO_ODR_ODR0_Pos) /*!< 0x00000001 */ +#define GPIO_ODR_ODR0 GPIO_ODR_ODR0_Msk /*!< Port output data, bit 0 */ +#define GPIO_ODR_ODR1_Pos (1U) +#define GPIO_ODR_ODR1_Msk (0x1UL << GPIO_ODR_ODR1_Pos) /*!< 0x00000002 */ +#define GPIO_ODR_ODR1 GPIO_ODR_ODR1_Msk /*!< Port output data, bit 1 */ +#define GPIO_ODR_ODR2_Pos (2U) +#define GPIO_ODR_ODR2_Msk (0x1UL << GPIO_ODR_ODR2_Pos) /*!< 0x00000004 */ +#define GPIO_ODR_ODR2 GPIO_ODR_ODR2_Msk /*!< Port output data, bit 2 */ +#define GPIO_ODR_ODR3_Pos (3U) +#define GPIO_ODR_ODR3_Msk (0x1UL << GPIO_ODR_ODR3_Pos) /*!< 0x00000008 */ +#define GPIO_ODR_ODR3 GPIO_ODR_ODR3_Msk /*!< Port output data, bit 3 */ +#define GPIO_ODR_ODR4_Pos (4U) +#define GPIO_ODR_ODR4_Msk (0x1UL << GPIO_ODR_ODR4_Pos) /*!< 0x00000010 */ +#define GPIO_ODR_ODR4 GPIO_ODR_ODR4_Msk /*!< Port output data, bit 4 */ +#define GPIO_ODR_ODR5_Pos (5U) +#define GPIO_ODR_ODR5_Msk (0x1UL << GPIO_ODR_ODR5_Pos) /*!< 0x00000020 */ +#define GPIO_ODR_ODR5 GPIO_ODR_ODR5_Msk /*!< Port output data, bit 5 */ +#define GPIO_ODR_ODR6_Pos (6U) +#define GPIO_ODR_ODR6_Msk (0x1UL << GPIO_ODR_ODR6_Pos) /*!< 0x00000040 */ +#define GPIO_ODR_ODR6 GPIO_ODR_ODR6_Msk /*!< Port output data, bit 6 */ +#define GPIO_ODR_ODR7_Pos (7U) +#define GPIO_ODR_ODR7_Msk (0x1UL << GPIO_ODR_ODR7_Pos) /*!< 0x00000080 */ +#define GPIO_ODR_ODR7 GPIO_ODR_ODR7_Msk /*!< Port output data, bit 7 */ +#define GPIO_ODR_ODR8_Pos (8U) +#define GPIO_ODR_ODR8_Msk (0x1UL << GPIO_ODR_ODR8_Pos) /*!< 0x00000100 */ +#define GPIO_ODR_ODR8 GPIO_ODR_ODR8_Msk /*!< Port output data, bit 8 */ +#define GPIO_ODR_ODR9_Pos (9U) +#define GPIO_ODR_ODR9_Msk (0x1UL << GPIO_ODR_ODR9_Pos) /*!< 0x00000200 */ +#define GPIO_ODR_ODR9 GPIO_ODR_ODR9_Msk /*!< Port output data, bit 9 */ +#define GPIO_ODR_ODR10_Pos (10U) +#define GPIO_ODR_ODR10_Msk (0x1UL << GPIO_ODR_ODR10_Pos) /*!< 0x00000400 */ +#define GPIO_ODR_ODR10 GPIO_ODR_ODR10_Msk /*!< Port output data, bit 10 */ +#define GPIO_ODR_ODR11_Pos (11U) +#define GPIO_ODR_ODR11_Msk (0x1UL << GPIO_ODR_ODR11_Pos) /*!< 0x00000800 */ +#define GPIO_ODR_ODR11 GPIO_ODR_ODR11_Msk /*!< Port output data, bit 11 */ +#define GPIO_ODR_ODR12_Pos (12U) +#define GPIO_ODR_ODR12_Msk (0x1UL << GPIO_ODR_ODR12_Pos) /*!< 0x00001000 */ +#define GPIO_ODR_ODR12 GPIO_ODR_ODR12_Msk /*!< Port output data, bit 12 */ +#define GPIO_ODR_ODR13_Pos (13U) +#define GPIO_ODR_ODR13_Msk (0x1UL << GPIO_ODR_ODR13_Pos) /*!< 0x00002000 */ +#define GPIO_ODR_ODR13 GPIO_ODR_ODR13_Msk /*!< Port output data, bit 13 */ +#define GPIO_ODR_ODR14_Pos (14U) +#define GPIO_ODR_ODR14_Msk (0x1UL << GPIO_ODR_ODR14_Pos) /*!< 0x00004000 */ +#define GPIO_ODR_ODR14 GPIO_ODR_ODR14_Msk /*!< Port output data, bit 14 */ +#define GPIO_ODR_ODR15_Pos (15U) +#define GPIO_ODR_ODR15_Msk (0x1UL << GPIO_ODR_ODR15_Pos) /*!< 0x00008000 */ +#define GPIO_ODR_ODR15 GPIO_ODR_ODR15_Msk /*!< Port output data, bit 15 */ + +/****************** Bit definition for GPIO_BSRR register *******************/ +#define GPIO_BSRR_BS0_Pos (0U) +#define GPIO_BSRR_BS0_Msk (0x1UL << GPIO_BSRR_BS0_Pos) /*!< 0x00000001 */ +#define GPIO_BSRR_BS0 GPIO_BSRR_BS0_Msk /*!< Port x Set bit 0 */ +#define GPIO_BSRR_BS1_Pos (1U) +#define GPIO_BSRR_BS1_Msk (0x1UL << GPIO_BSRR_BS1_Pos) /*!< 0x00000002 */ +#define GPIO_BSRR_BS1 GPIO_BSRR_BS1_Msk /*!< Port x Set bit 1 */ +#define GPIO_BSRR_BS2_Pos (2U) +#define GPIO_BSRR_BS2_Msk (0x1UL << GPIO_BSRR_BS2_Pos) /*!< 0x00000004 */ +#define GPIO_BSRR_BS2 GPIO_BSRR_BS2_Msk /*!< Port x Set bit 2 */ +#define GPIO_BSRR_BS3_Pos (3U) +#define GPIO_BSRR_BS3_Msk (0x1UL << GPIO_BSRR_BS3_Pos) /*!< 0x00000008 */ +#define GPIO_BSRR_BS3 GPIO_BSRR_BS3_Msk /*!< Port x Set bit 3 */ +#define GPIO_BSRR_BS4_Pos (4U) +#define GPIO_BSRR_BS4_Msk (0x1UL << GPIO_BSRR_BS4_Pos) /*!< 0x00000010 */ +#define GPIO_BSRR_BS4 GPIO_BSRR_BS4_Msk /*!< Port x Set bit 4 */ +#define GPIO_BSRR_BS5_Pos (5U) +#define GPIO_BSRR_BS5_Msk (0x1UL << GPIO_BSRR_BS5_Pos) /*!< 0x00000020 */ +#define GPIO_BSRR_BS5 GPIO_BSRR_BS5_Msk /*!< Port x Set bit 5 */ +#define GPIO_BSRR_BS6_Pos (6U) +#define GPIO_BSRR_BS6_Msk (0x1UL << GPIO_BSRR_BS6_Pos) /*!< 0x00000040 */ +#define GPIO_BSRR_BS6 GPIO_BSRR_BS6_Msk /*!< Port x Set bit 6 */ +#define GPIO_BSRR_BS7_Pos (7U) +#define GPIO_BSRR_BS7_Msk (0x1UL << GPIO_BSRR_BS7_Pos) /*!< 0x00000080 */ +#define GPIO_BSRR_BS7 GPIO_BSRR_BS7_Msk /*!< Port x Set bit 7 */ +#define GPIO_BSRR_BS8_Pos (8U) +#define GPIO_BSRR_BS8_Msk (0x1UL << GPIO_BSRR_BS8_Pos) /*!< 0x00000100 */ +#define GPIO_BSRR_BS8 GPIO_BSRR_BS8_Msk /*!< Port x Set bit 8 */ +#define GPIO_BSRR_BS9_Pos (9U) +#define GPIO_BSRR_BS9_Msk (0x1UL << GPIO_BSRR_BS9_Pos) /*!< 0x00000200 */ +#define GPIO_BSRR_BS9 GPIO_BSRR_BS9_Msk /*!< Port x Set bit 9 */ +#define GPIO_BSRR_BS10_Pos (10U) +#define GPIO_BSRR_BS10_Msk (0x1UL << GPIO_BSRR_BS10_Pos) /*!< 0x00000400 */ +#define GPIO_BSRR_BS10 GPIO_BSRR_BS10_Msk /*!< Port x Set bit 10 */ +#define GPIO_BSRR_BS11_Pos (11U) +#define GPIO_BSRR_BS11_Msk (0x1UL << GPIO_BSRR_BS11_Pos) /*!< 0x00000800 */ +#define GPIO_BSRR_BS11 GPIO_BSRR_BS11_Msk /*!< Port x Set bit 11 */ +#define GPIO_BSRR_BS12_Pos (12U) +#define GPIO_BSRR_BS12_Msk (0x1UL << GPIO_BSRR_BS12_Pos) /*!< 0x00001000 */ +#define GPIO_BSRR_BS12 GPIO_BSRR_BS12_Msk /*!< Port x Set bit 12 */ +#define GPIO_BSRR_BS13_Pos (13U) +#define GPIO_BSRR_BS13_Msk (0x1UL << GPIO_BSRR_BS13_Pos) /*!< 0x00002000 */ +#define GPIO_BSRR_BS13 GPIO_BSRR_BS13_Msk /*!< Port x Set bit 13 */ +#define GPIO_BSRR_BS14_Pos (14U) +#define GPIO_BSRR_BS14_Msk (0x1UL << GPIO_BSRR_BS14_Pos) /*!< 0x00004000 */ +#define GPIO_BSRR_BS14 GPIO_BSRR_BS14_Msk /*!< Port x Set bit 14 */ +#define GPIO_BSRR_BS15_Pos (15U) +#define GPIO_BSRR_BS15_Msk (0x1UL << GPIO_BSRR_BS15_Pos) /*!< 0x00008000 */ +#define GPIO_BSRR_BS15 GPIO_BSRR_BS15_Msk /*!< Port x Set bit 15 */ + +#define GPIO_BSRR_BR0_Pos (16U) +#define GPIO_BSRR_BR0_Msk (0x1UL << GPIO_BSRR_BR0_Pos) /*!< 0x00010000 */ +#define GPIO_BSRR_BR0 GPIO_BSRR_BR0_Msk /*!< Port x Reset bit 0 */ +#define GPIO_BSRR_BR1_Pos (17U) +#define GPIO_BSRR_BR1_Msk (0x1UL << GPIO_BSRR_BR1_Pos) /*!< 0x00020000 */ +#define GPIO_BSRR_BR1 GPIO_BSRR_BR1_Msk /*!< Port x Reset bit 1 */ +#define GPIO_BSRR_BR2_Pos (18U) +#define GPIO_BSRR_BR2_Msk (0x1UL << GPIO_BSRR_BR2_Pos) /*!< 0x00040000 */ +#define GPIO_BSRR_BR2 GPIO_BSRR_BR2_Msk /*!< Port x Reset bit 2 */ +#define GPIO_BSRR_BR3_Pos (19U) +#define GPIO_BSRR_BR3_Msk (0x1UL << GPIO_BSRR_BR3_Pos) /*!< 0x00080000 */ +#define GPIO_BSRR_BR3 GPIO_BSRR_BR3_Msk /*!< Port x Reset bit 3 */ +#define GPIO_BSRR_BR4_Pos (20U) +#define GPIO_BSRR_BR4_Msk (0x1UL << GPIO_BSRR_BR4_Pos) /*!< 0x00100000 */ +#define GPIO_BSRR_BR4 GPIO_BSRR_BR4_Msk /*!< Port x Reset bit 4 */ +#define GPIO_BSRR_BR5_Pos (21U) +#define GPIO_BSRR_BR5_Msk (0x1UL << GPIO_BSRR_BR5_Pos) /*!< 0x00200000 */ +#define GPIO_BSRR_BR5 GPIO_BSRR_BR5_Msk /*!< Port x Reset bit 5 */ +#define GPIO_BSRR_BR6_Pos (22U) +#define GPIO_BSRR_BR6_Msk (0x1UL << GPIO_BSRR_BR6_Pos) /*!< 0x00400000 */ +#define GPIO_BSRR_BR6 GPIO_BSRR_BR6_Msk /*!< Port x Reset bit 6 */ +#define GPIO_BSRR_BR7_Pos (23U) +#define GPIO_BSRR_BR7_Msk (0x1UL << GPIO_BSRR_BR7_Pos) /*!< 0x00800000 */ +#define GPIO_BSRR_BR7 GPIO_BSRR_BR7_Msk /*!< Port x Reset bit 7 */ +#define GPIO_BSRR_BR8_Pos (24U) +#define GPIO_BSRR_BR8_Msk (0x1UL << GPIO_BSRR_BR8_Pos) /*!< 0x01000000 */ +#define GPIO_BSRR_BR8 GPIO_BSRR_BR8_Msk /*!< Port x Reset bit 8 */ +#define GPIO_BSRR_BR9_Pos (25U) +#define GPIO_BSRR_BR9_Msk (0x1UL << GPIO_BSRR_BR9_Pos) /*!< 0x02000000 */ +#define GPIO_BSRR_BR9 GPIO_BSRR_BR9_Msk /*!< Port x Reset bit 9 */ +#define GPIO_BSRR_BR10_Pos (26U) +#define GPIO_BSRR_BR10_Msk (0x1UL << GPIO_BSRR_BR10_Pos) /*!< 0x04000000 */ +#define GPIO_BSRR_BR10 GPIO_BSRR_BR10_Msk /*!< Port x Reset bit 10 */ +#define GPIO_BSRR_BR11_Pos (27U) +#define GPIO_BSRR_BR11_Msk (0x1UL << GPIO_BSRR_BR11_Pos) /*!< 0x08000000 */ +#define GPIO_BSRR_BR11 GPIO_BSRR_BR11_Msk /*!< Port x Reset bit 11 */ +#define GPIO_BSRR_BR12_Pos (28U) +#define GPIO_BSRR_BR12_Msk (0x1UL << GPIO_BSRR_BR12_Pos) /*!< 0x10000000 */ +#define GPIO_BSRR_BR12 GPIO_BSRR_BR12_Msk /*!< Port x Reset bit 12 */ +#define GPIO_BSRR_BR13_Pos (29U) +#define GPIO_BSRR_BR13_Msk (0x1UL << GPIO_BSRR_BR13_Pos) /*!< 0x20000000 */ +#define GPIO_BSRR_BR13 GPIO_BSRR_BR13_Msk /*!< Port x Reset bit 13 */ +#define GPIO_BSRR_BR14_Pos (30U) +#define GPIO_BSRR_BR14_Msk (0x1UL << GPIO_BSRR_BR14_Pos) /*!< 0x40000000 */ +#define GPIO_BSRR_BR14 GPIO_BSRR_BR14_Msk /*!< Port x Reset bit 14 */ +#define GPIO_BSRR_BR15_Pos (31U) +#define GPIO_BSRR_BR15_Msk (0x1UL << GPIO_BSRR_BR15_Pos) /*!< 0x80000000 */ +#define GPIO_BSRR_BR15 GPIO_BSRR_BR15_Msk /*!< Port x Reset bit 15 */ + +/******************* Bit definition for GPIO_BRR register *******************/ +#define GPIO_BRR_BR0_Pos (0U) +#define GPIO_BRR_BR0_Msk (0x1UL << GPIO_BRR_BR0_Pos) /*!< 0x00000001 */ +#define GPIO_BRR_BR0 GPIO_BRR_BR0_Msk /*!< Port x Reset bit 0 */ +#define GPIO_BRR_BR1_Pos (1U) +#define GPIO_BRR_BR1_Msk (0x1UL << GPIO_BRR_BR1_Pos) /*!< 0x00000002 */ +#define GPIO_BRR_BR1 GPIO_BRR_BR1_Msk /*!< Port x Reset bit 1 */ +#define GPIO_BRR_BR2_Pos (2U) +#define GPIO_BRR_BR2_Msk (0x1UL << GPIO_BRR_BR2_Pos) /*!< 0x00000004 */ +#define GPIO_BRR_BR2 GPIO_BRR_BR2_Msk /*!< Port x Reset bit 2 */ +#define GPIO_BRR_BR3_Pos (3U) +#define GPIO_BRR_BR3_Msk (0x1UL << GPIO_BRR_BR3_Pos) /*!< 0x00000008 */ +#define GPIO_BRR_BR3 GPIO_BRR_BR3_Msk /*!< Port x Reset bit 3 */ +#define GPIO_BRR_BR4_Pos (4U) +#define GPIO_BRR_BR4_Msk (0x1UL << GPIO_BRR_BR4_Pos) /*!< 0x00000010 */ +#define GPIO_BRR_BR4 GPIO_BRR_BR4_Msk /*!< Port x Reset bit 4 */ +#define GPIO_BRR_BR5_Pos (5U) +#define GPIO_BRR_BR5_Msk (0x1UL << GPIO_BRR_BR5_Pos) /*!< 0x00000020 */ +#define GPIO_BRR_BR5 GPIO_BRR_BR5_Msk /*!< Port x Reset bit 5 */ +#define GPIO_BRR_BR6_Pos (6U) +#define GPIO_BRR_BR6_Msk (0x1UL << GPIO_BRR_BR6_Pos) /*!< 0x00000040 */ +#define GPIO_BRR_BR6 GPIO_BRR_BR6_Msk /*!< Port x Reset bit 6 */ +#define GPIO_BRR_BR7_Pos (7U) +#define GPIO_BRR_BR7_Msk (0x1UL << GPIO_BRR_BR7_Pos) /*!< 0x00000080 */ +#define GPIO_BRR_BR7 GPIO_BRR_BR7_Msk /*!< Port x Reset bit 7 */ +#define GPIO_BRR_BR8_Pos (8U) +#define GPIO_BRR_BR8_Msk (0x1UL << GPIO_BRR_BR8_Pos) /*!< 0x00000100 */ +#define GPIO_BRR_BR8 GPIO_BRR_BR8_Msk /*!< Port x Reset bit 8 */ +#define GPIO_BRR_BR9_Pos (9U) +#define GPIO_BRR_BR9_Msk (0x1UL << GPIO_BRR_BR9_Pos) /*!< 0x00000200 */ +#define GPIO_BRR_BR9 GPIO_BRR_BR9_Msk /*!< Port x Reset bit 9 */ +#define GPIO_BRR_BR10_Pos (10U) +#define GPIO_BRR_BR10_Msk (0x1UL << GPIO_BRR_BR10_Pos) /*!< 0x00000400 */ +#define GPIO_BRR_BR10 GPIO_BRR_BR10_Msk /*!< Port x Reset bit 10 */ +#define GPIO_BRR_BR11_Pos (11U) +#define GPIO_BRR_BR11_Msk (0x1UL << GPIO_BRR_BR11_Pos) /*!< 0x00000800 */ +#define GPIO_BRR_BR11 GPIO_BRR_BR11_Msk /*!< Port x Reset bit 11 */ +#define GPIO_BRR_BR12_Pos (12U) +#define GPIO_BRR_BR12_Msk (0x1UL << GPIO_BRR_BR12_Pos) /*!< 0x00001000 */ +#define GPIO_BRR_BR12 GPIO_BRR_BR12_Msk /*!< Port x Reset bit 12 */ +#define GPIO_BRR_BR13_Pos (13U) +#define GPIO_BRR_BR13_Msk (0x1UL << GPIO_BRR_BR13_Pos) /*!< 0x00002000 */ +#define GPIO_BRR_BR13 GPIO_BRR_BR13_Msk /*!< Port x Reset bit 13 */ +#define GPIO_BRR_BR14_Pos (14U) +#define GPIO_BRR_BR14_Msk (0x1UL << GPIO_BRR_BR14_Pos) /*!< 0x00004000 */ +#define GPIO_BRR_BR14 GPIO_BRR_BR14_Msk /*!< Port x Reset bit 14 */ +#define GPIO_BRR_BR15_Pos (15U) +#define GPIO_BRR_BR15_Msk (0x1UL << GPIO_BRR_BR15_Pos) /*!< 0x00008000 */ +#define GPIO_BRR_BR15 GPIO_BRR_BR15_Msk /*!< Port x Reset bit 15 */ + +/****************** Bit definition for GPIO_LCKR register *******************/ +#define GPIO_LCKR_LCK0_Pos (0U) +#define GPIO_LCKR_LCK0_Msk (0x1UL << GPIO_LCKR_LCK0_Pos) /*!< 0x00000001 */ +#define GPIO_LCKR_LCK0 GPIO_LCKR_LCK0_Msk /*!< Port x Lock bit 0 */ +#define GPIO_LCKR_LCK1_Pos (1U) +#define GPIO_LCKR_LCK1_Msk (0x1UL << GPIO_LCKR_LCK1_Pos) /*!< 0x00000002 */ +#define GPIO_LCKR_LCK1 GPIO_LCKR_LCK1_Msk /*!< Port x Lock bit 1 */ +#define GPIO_LCKR_LCK2_Pos (2U) +#define GPIO_LCKR_LCK2_Msk (0x1UL << GPIO_LCKR_LCK2_Pos) /*!< 0x00000004 */ +#define GPIO_LCKR_LCK2 GPIO_LCKR_LCK2_Msk /*!< Port x Lock bit 2 */ +#define GPIO_LCKR_LCK3_Pos (3U) +#define GPIO_LCKR_LCK3_Msk (0x1UL << GPIO_LCKR_LCK3_Pos) /*!< 0x00000008 */ +#define GPIO_LCKR_LCK3 GPIO_LCKR_LCK3_Msk /*!< Port x Lock bit 3 */ +#define GPIO_LCKR_LCK4_Pos (4U) +#define GPIO_LCKR_LCK4_Msk (0x1UL << GPIO_LCKR_LCK4_Pos) /*!< 0x00000010 */ +#define GPIO_LCKR_LCK4 GPIO_LCKR_LCK4_Msk /*!< Port x Lock bit 4 */ +#define GPIO_LCKR_LCK5_Pos (5U) +#define GPIO_LCKR_LCK5_Msk (0x1UL << GPIO_LCKR_LCK5_Pos) /*!< 0x00000020 */ +#define GPIO_LCKR_LCK5 GPIO_LCKR_LCK5_Msk /*!< Port x Lock bit 5 */ +#define GPIO_LCKR_LCK6_Pos (6U) +#define GPIO_LCKR_LCK6_Msk (0x1UL << GPIO_LCKR_LCK6_Pos) /*!< 0x00000040 */ +#define GPIO_LCKR_LCK6 GPIO_LCKR_LCK6_Msk /*!< Port x Lock bit 6 */ +#define GPIO_LCKR_LCK7_Pos (7U) +#define GPIO_LCKR_LCK7_Msk (0x1UL << GPIO_LCKR_LCK7_Pos) /*!< 0x00000080 */ +#define GPIO_LCKR_LCK7 GPIO_LCKR_LCK7_Msk /*!< Port x Lock bit 7 */ +#define GPIO_LCKR_LCK8_Pos (8U) +#define GPIO_LCKR_LCK8_Msk (0x1UL << GPIO_LCKR_LCK8_Pos) /*!< 0x00000100 */ +#define GPIO_LCKR_LCK8 GPIO_LCKR_LCK8_Msk /*!< Port x Lock bit 8 */ +#define GPIO_LCKR_LCK9_Pos (9U) +#define GPIO_LCKR_LCK9_Msk (0x1UL << GPIO_LCKR_LCK9_Pos) /*!< 0x00000200 */ +#define GPIO_LCKR_LCK9 GPIO_LCKR_LCK9_Msk /*!< Port x Lock bit 9 */ +#define GPIO_LCKR_LCK10_Pos (10U) +#define GPIO_LCKR_LCK10_Msk (0x1UL << GPIO_LCKR_LCK10_Pos) /*!< 0x00000400 */ +#define GPIO_LCKR_LCK10 GPIO_LCKR_LCK10_Msk /*!< Port x Lock bit 10 */ +#define GPIO_LCKR_LCK11_Pos (11U) +#define GPIO_LCKR_LCK11_Msk (0x1UL << GPIO_LCKR_LCK11_Pos) /*!< 0x00000800 */ +#define GPIO_LCKR_LCK11 GPIO_LCKR_LCK11_Msk /*!< Port x Lock bit 11 */ +#define GPIO_LCKR_LCK12_Pos (12U) +#define GPIO_LCKR_LCK12_Msk (0x1UL << GPIO_LCKR_LCK12_Pos) /*!< 0x00001000 */ +#define GPIO_LCKR_LCK12 GPIO_LCKR_LCK12_Msk /*!< Port x Lock bit 12 */ +#define GPIO_LCKR_LCK13_Pos (13U) +#define GPIO_LCKR_LCK13_Msk (0x1UL << GPIO_LCKR_LCK13_Pos) /*!< 0x00002000 */ +#define GPIO_LCKR_LCK13 GPIO_LCKR_LCK13_Msk /*!< Port x Lock bit 13 */ +#define GPIO_LCKR_LCK14_Pos (14U) +#define GPIO_LCKR_LCK14_Msk (0x1UL << GPIO_LCKR_LCK14_Pos) /*!< 0x00004000 */ +#define GPIO_LCKR_LCK14 GPIO_LCKR_LCK14_Msk /*!< Port x Lock bit 14 */ +#define GPIO_LCKR_LCK15_Pos (15U) +#define GPIO_LCKR_LCK15_Msk (0x1UL << GPIO_LCKR_LCK15_Pos) /*!< 0x00008000 */ +#define GPIO_LCKR_LCK15 GPIO_LCKR_LCK15_Msk /*!< Port x Lock bit 15 */ +#define GPIO_LCKR_LCKK_Pos (16U) +#define GPIO_LCKR_LCKK_Msk (0x1UL << GPIO_LCKR_LCKK_Pos) /*!< 0x00010000 */ +#define GPIO_LCKR_LCKK GPIO_LCKR_LCKK_Msk /*!< Lock key */ + +/*----------------------------------------------------------------------------*/ + +/****************** Bit definition for AFIO_EVCR register *******************/ +#define AFIO_EVCR_PIN_Pos (0U) +#define AFIO_EVCR_PIN_Msk (0xFUL << AFIO_EVCR_PIN_Pos) /*!< 0x0000000F */ +#define AFIO_EVCR_PIN AFIO_EVCR_PIN_Msk /*!< PIN[3:0] bits (Pin selection) */ +#define AFIO_EVCR_PIN_0 (0x1UL << AFIO_EVCR_PIN_Pos) /*!< 0x00000001 */ +#define AFIO_EVCR_PIN_1 (0x2UL << AFIO_EVCR_PIN_Pos) /*!< 0x00000002 */ +#define AFIO_EVCR_PIN_2 (0x4UL << AFIO_EVCR_PIN_Pos) /*!< 0x00000004 */ +#define AFIO_EVCR_PIN_3 (0x8UL << AFIO_EVCR_PIN_Pos) /*!< 0x00000008 */ + +/*!< PIN configuration */ +#define AFIO_EVCR_PIN_PX0 0x00000000U /*!< Pin 0 selected */ +#define AFIO_EVCR_PIN_PX1_Pos (0U) +#define AFIO_EVCR_PIN_PX1_Msk (0x1UL << AFIO_EVCR_PIN_PX1_Pos) /*!< 0x00000001 */ +#define AFIO_EVCR_PIN_PX1 AFIO_EVCR_PIN_PX1_Msk /*!< Pin 1 selected */ +#define AFIO_EVCR_PIN_PX2_Pos (1U) +#define AFIO_EVCR_PIN_PX2_Msk (0x1UL << AFIO_EVCR_PIN_PX2_Pos) /*!< 0x00000002 */ +#define AFIO_EVCR_PIN_PX2 AFIO_EVCR_PIN_PX2_Msk /*!< Pin 2 selected */ +#define AFIO_EVCR_PIN_PX3_Pos (0U) +#define AFIO_EVCR_PIN_PX3_Msk (0x3UL << AFIO_EVCR_PIN_PX3_Pos) /*!< 0x00000003 */ +#define AFIO_EVCR_PIN_PX3 AFIO_EVCR_PIN_PX3_Msk /*!< Pin 3 selected */ +#define AFIO_EVCR_PIN_PX4_Pos (2U) +#define AFIO_EVCR_PIN_PX4_Msk (0x1UL << AFIO_EVCR_PIN_PX4_Pos) /*!< 0x00000004 */ +#define AFIO_EVCR_PIN_PX4 AFIO_EVCR_PIN_PX4_Msk /*!< Pin 4 selected */ +#define AFIO_EVCR_PIN_PX5_Pos (0U) +#define AFIO_EVCR_PIN_PX5_Msk (0x5UL << AFIO_EVCR_PIN_PX5_Pos) /*!< 0x00000005 */ +#define AFIO_EVCR_PIN_PX5 AFIO_EVCR_PIN_PX5_Msk /*!< Pin 5 selected */ +#define AFIO_EVCR_PIN_PX6_Pos (1U) +#define AFIO_EVCR_PIN_PX6_Msk (0x3UL << AFIO_EVCR_PIN_PX6_Pos) /*!< 0x00000006 */ +#define AFIO_EVCR_PIN_PX6 AFIO_EVCR_PIN_PX6_Msk /*!< Pin 6 selected */ +#define AFIO_EVCR_PIN_PX7_Pos (0U) +#define AFIO_EVCR_PIN_PX7_Msk (0x7UL << AFIO_EVCR_PIN_PX7_Pos) /*!< 0x00000007 */ +#define AFIO_EVCR_PIN_PX7 AFIO_EVCR_PIN_PX7_Msk /*!< Pin 7 selected */ +#define AFIO_EVCR_PIN_PX8_Pos (3U) +#define AFIO_EVCR_PIN_PX8_Msk (0x1UL << AFIO_EVCR_PIN_PX8_Pos) /*!< 0x00000008 */ +#define AFIO_EVCR_PIN_PX8 AFIO_EVCR_PIN_PX8_Msk /*!< Pin 8 selected */ +#define AFIO_EVCR_PIN_PX9_Pos (0U) +#define AFIO_EVCR_PIN_PX9_Msk (0x9UL << AFIO_EVCR_PIN_PX9_Pos) /*!< 0x00000009 */ +#define AFIO_EVCR_PIN_PX9 AFIO_EVCR_PIN_PX9_Msk /*!< Pin 9 selected */ +#define AFIO_EVCR_PIN_PX10_Pos (1U) +#define AFIO_EVCR_PIN_PX10_Msk (0x5UL << AFIO_EVCR_PIN_PX10_Pos) /*!< 0x0000000A */ +#define AFIO_EVCR_PIN_PX10 AFIO_EVCR_PIN_PX10_Msk /*!< Pin 10 selected */ +#define AFIO_EVCR_PIN_PX11_Pos (0U) +#define AFIO_EVCR_PIN_PX11_Msk (0xBUL << AFIO_EVCR_PIN_PX11_Pos) /*!< 0x0000000B */ +#define AFIO_EVCR_PIN_PX11 AFIO_EVCR_PIN_PX11_Msk /*!< Pin 11 selected */ +#define AFIO_EVCR_PIN_PX12_Pos (2U) +#define AFIO_EVCR_PIN_PX12_Msk (0x3UL << AFIO_EVCR_PIN_PX12_Pos) /*!< 0x0000000C */ +#define AFIO_EVCR_PIN_PX12 AFIO_EVCR_PIN_PX12_Msk /*!< Pin 12 selected */ +#define AFIO_EVCR_PIN_PX13_Pos (0U) +#define AFIO_EVCR_PIN_PX13_Msk (0xDUL << AFIO_EVCR_PIN_PX13_Pos) /*!< 0x0000000D */ +#define AFIO_EVCR_PIN_PX13 AFIO_EVCR_PIN_PX13_Msk /*!< Pin 13 selected */ +#define AFIO_EVCR_PIN_PX14_Pos (1U) +#define AFIO_EVCR_PIN_PX14_Msk (0x7UL << AFIO_EVCR_PIN_PX14_Pos) /*!< 0x0000000E */ +#define AFIO_EVCR_PIN_PX14 AFIO_EVCR_PIN_PX14_Msk /*!< Pin 14 selected */ +#define AFIO_EVCR_PIN_PX15_Pos (0U) +#define AFIO_EVCR_PIN_PX15_Msk (0xFUL << AFIO_EVCR_PIN_PX15_Pos) /*!< 0x0000000F */ +#define AFIO_EVCR_PIN_PX15 AFIO_EVCR_PIN_PX15_Msk /*!< Pin 15 selected */ + +#define AFIO_EVCR_PORT_Pos (4U) +#define AFIO_EVCR_PORT_Msk (0x7UL << AFIO_EVCR_PORT_Pos) /*!< 0x00000070 */ +#define AFIO_EVCR_PORT AFIO_EVCR_PORT_Msk /*!< PORT[2:0] bits (Port selection) */ +#define AFIO_EVCR_PORT_0 (0x1UL << AFIO_EVCR_PORT_Pos) /*!< 0x00000010 */ +#define AFIO_EVCR_PORT_1 (0x2UL << AFIO_EVCR_PORT_Pos) /*!< 0x00000020 */ +#define AFIO_EVCR_PORT_2 (0x4UL << AFIO_EVCR_PORT_Pos) /*!< 0x00000040 */ + +/*!< PORT configuration */ +#define AFIO_EVCR_PORT_PA 0x00000000 /*!< Port A selected */ +#define AFIO_EVCR_PORT_PB_Pos (4U) +#define AFIO_EVCR_PORT_PB_Msk (0x1UL << AFIO_EVCR_PORT_PB_Pos) /*!< 0x00000010 */ +#define AFIO_EVCR_PORT_PB AFIO_EVCR_PORT_PB_Msk /*!< Port B selected */ +#define AFIO_EVCR_PORT_PC_Pos (5U) +#define AFIO_EVCR_PORT_PC_Msk (0x1UL << AFIO_EVCR_PORT_PC_Pos) /*!< 0x00000020 */ +#define AFIO_EVCR_PORT_PC AFIO_EVCR_PORT_PC_Msk /*!< Port C selected */ +#define AFIO_EVCR_PORT_PD_Pos (4U) +#define AFIO_EVCR_PORT_PD_Msk (0x3UL << AFIO_EVCR_PORT_PD_Pos) /*!< 0x00000030 */ +#define AFIO_EVCR_PORT_PD AFIO_EVCR_PORT_PD_Msk /*!< Port D selected */ +#define AFIO_EVCR_PORT_PE_Pos (6U) +#define AFIO_EVCR_PORT_PE_Msk (0x1UL << AFIO_EVCR_PORT_PE_Pos) /*!< 0x00000040 */ +#define AFIO_EVCR_PORT_PE AFIO_EVCR_PORT_PE_Msk /*!< Port E selected */ + +#define AFIO_EVCR_EVOE_Pos (7U) +#define AFIO_EVCR_EVOE_Msk (0x1UL << AFIO_EVCR_EVOE_Pos) /*!< 0x00000080 */ +#define AFIO_EVCR_EVOE AFIO_EVCR_EVOE_Msk /*!< Event Output Enable */ + +/****************** Bit definition for AFIO_MAPR register *******************/ +#define AFIO_MAPR_SPI1_REMAP_Pos (0U) +#define AFIO_MAPR_SPI1_REMAP_Msk (0x1UL << AFIO_MAPR_SPI1_REMAP_Pos) /*!< 0x00000001 */ +#define AFIO_MAPR_SPI1_REMAP AFIO_MAPR_SPI1_REMAP_Msk /*!< SPI1 remapping */ +#define AFIO_MAPR_I2C1_REMAP_Pos (1U) +#define AFIO_MAPR_I2C1_REMAP_Msk (0x1UL << AFIO_MAPR_I2C1_REMAP_Pos) /*!< 0x00000002 */ +#define AFIO_MAPR_I2C1_REMAP AFIO_MAPR_I2C1_REMAP_Msk /*!< I2C1 remapping */ +#define AFIO_MAPR_USART1_REMAP_Pos (2U) +#define AFIO_MAPR_USART1_REMAP_Msk (0x1UL << AFIO_MAPR_USART1_REMAP_Pos) /*!< 0x00000004 */ +#define AFIO_MAPR_USART1_REMAP AFIO_MAPR_USART1_REMAP_Msk /*!< USART1 remapping */ +#define AFIO_MAPR_USART2_REMAP_Pos (3U) +#define AFIO_MAPR_USART2_REMAP_Msk (0x1UL << AFIO_MAPR_USART2_REMAP_Pos) /*!< 0x00000008 */ +#define AFIO_MAPR_USART2_REMAP AFIO_MAPR_USART2_REMAP_Msk /*!< USART2 remapping */ + + +#define AFIO_MAPR_TIM1_REMAP_Pos (6U) +#define AFIO_MAPR_TIM1_REMAP_Msk (0x3UL << AFIO_MAPR_TIM1_REMAP_Pos) /*!< 0x000000C0 */ +#define AFIO_MAPR_TIM1_REMAP AFIO_MAPR_TIM1_REMAP_Msk /*!< TIM1_REMAP[1:0] bits (TIM1 remapping) */ +#define AFIO_MAPR_TIM1_REMAP_0 (0x1UL << AFIO_MAPR_TIM1_REMAP_Pos) /*!< 0x00000040 */ +#define AFIO_MAPR_TIM1_REMAP_1 (0x2UL << AFIO_MAPR_TIM1_REMAP_Pos) /*!< 0x00000080 */ + +/*!< TIM1_REMAP configuration */ +#define AFIO_MAPR_TIM1_REMAP_NOREMAP 0x00000000U /*!< No remap (ETR/PA12, CH1/PA8, CH2/PA9, CH3/PA10, CH4/PA11, BKIN/PB12, CH1N/PB13, CH2N/PB14, CH3N/PB15) */ +#define AFIO_MAPR_TIM1_REMAP_PARTIALREMAP_Pos (6U) +#define AFIO_MAPR_TIM1_REMAP_PARTIALREMAP_Msk (0x1UL << AFIO_MAPR_TIM1_REMAP_PARTIALREMAP_Pos) /*!< 0x00000040 */ +#define AFIO_MAPR_TIM1_REMAP_PARTIALREMAP AFIO_MAPR_TIM1_REMAP_PARTIALREMAP_Msk /*!< Partial remap (ETR/PA12, CH1/PA8, CH2/PA9, CH3/PA10, CH4/PA11, BKIN/PA6, CH1N/PA7, CH2N/PB0, CH3N/PB1) */ +#define AFIO_MAPR_TIM1_REMAP_FULLREMAP_Pos (6U) +#define AFIO_MAPR_TIM1_REMAP_FULLREMAP_Msk (0x3UL << AFIO_MAPR_TIM1_REMAP_FULLREMAP_Pos) /*!< 0x000000C0 */ +#define AFIO_MAPR_TIM1_REMAP_FULLREMAP AFIO_MAPR_TIM1_REMAP_FULLREMAP_Msk /*!< Full remap (ETR/PE7, CH1/PE9, CH2/PE11, CH3/PE13, CH4/PE14, BKIN/PE15, CH1N/PE8, CH2N/PE10, CH3N/PE12) */ + +#define AFIO_MAPR_TIM2_REMAP_Pos (8U) +#define AFIO_MAPR_TIM2_REMAP_Msk (0x3UL << AFIO_MAPR_TIM2_REMAP_Pos) /*!< 0x00000300 */ +#define AFIO_MAPR_TIM2_REMAP AFIO_MAPR_TIM2_REMAP_Msk /*!< TIM2_REMAP[1:0] bits (TIM2 remapping) */ +#define AFIO_MAPR_TIM2_REMAP_0 (0x1UL << AFIO_MAPR_TIM2_REMAP_Pos) /*!< 0x00000100 */ +#define AFIO_MAPR_TIM2_REMAP_1 (0x2UL << AFIO_MAPR_TIM2_REMAP_Pos) /*!< 0x00000200 */ + +/*!< TIM2_REMAP configuration */ +#define AFIO_MAPR_TIM2_REMAP_NOREMAP 0x00000000U /*!< No remap (CH1/ETR/PA0, CH2/PA1, CH3/PA2, CH4/PA3) */ +#define AFIO_MAPR_TIM2_REMAP_PARTIALREMAP1_Pos (8U) +#define AFIO_MAPR_TIM2_REMAP_PARTIALREMAP1_Msk (0x1UL << AFIO_MAPR_TIM2_REMAP_PARTIALREMAP1_Pos) /*!< 0x00000100 */ +#define AFIO_MAPR_TIM2_REMAP_PARTIALREMAP1 AFIO_MAPR_TIM2_REMAP_PARTIALREMAP1_Msk /*!< Partial remap (CH1/ETR/PA15, CH2/PB3, CH3/PA2, CH4/PA3) */ +#define AFIO_MAPR_TIM2_REMAP_PARTIALREMAP2_Pos (9U) +#define AFIO_MAPR_TIM2_REMAP_PARTIALREMAP2_Msk (0x1UL << AFIO_MAPR_TIM2_REMAP_PARTIALREMAP2_Pos) /*!< 0x00000200 */ +#define AFIO_MAPR_TIM2_REMAP_PARTIALREMAP2 AFIO_MAPR_TIM2_REMAP_PARTIALREMAP2_Msk /*!< Partial remap (CH1/ETR/PA0, CH2/PA1, CH3/PB10, CH4/PB11) */ +#define AFIO_MAPR_TIM2_REMAP_FULLREMAP_Pos (8U) +#define AFIO_MAPR_TIM2_REMAP_FULLREMAP_Msk (0x3UL << AFIO_MAPR_TIM2_REMAP_FULLREMAP_Pos) /*!< 0x00000300 */ +#define AFIO_MAPR_TIM2_REMAP_FULLREMAP AFIO_MAPR_TIM2_REMAP_FULLREMAP_Msk /*!< Full remap (CH1/ETR/PA15, CH2/PB3, CH3/PB10, CH4/PB11) */ + +#define AFIO_MAPR_TIM3_REMAP_Pos (10U) +#define AFIO_MAPR_TIM3_REMAP_Msk (0x3UL << AFIO_MAPR_TIM3_REMAP_Pos) /*!< 0x00000C00 */ +#define AFIO_MAPR_TIM3_REMAP AFIO_MAPR_TIM3_REMAP_Msk /*!< TIM3_REMAP[1:0] bits (TIM3 remapping) */ +#define AFIO_MAPR_TIM3_REMAP_0 (0x1UL << AFIO_MAPR_TIM3_REMAP_Pos) /*!< 0x00000400 */ +#define AFIO_MAPR_TIM3_REMAP_1 (0x2UL << AFIO_MAPR_TIM3_REMAP_Pos) /*!< 0x00000800 */ + +/*!< TIM3_REMAP configuration */ +#define AFIO_MAPR_TIM3_REMAP_NOREMAP 0x00000000U /*!< No remap (CH1/PA6, CH2/PA7, CH3/PB0, CH4/PB1) */ +#define AFIO_MAPR_TIM3_REMAP_PARTIALREMAP_Pos (11U) +#define AFIO_MAPR_TIM3_REMAP_PARTIALREMAP_Msk (0x1UL << AFIO_MAPR_TIM3_REMAP_PARTIALREMAP_Pos) /*!< 0x00000800 */ +#define AFIO_MAPR_TIM3_REMAP_PARTIALREMAP AFIO_MAPR_TIM3_REMAP_PARTIALREMAP_Msk /*!< Partial remap (CH1/PB4, CH2/PB5, CH3/PB0, CH4/PB1) */ +#define AFIO_MAPR_TIM3_REMAP_FULLREMAP_Pos (10U) +#define AFIO_MAPR_TIM3_REMAP_FULLREMAP_Msk (0x3UL << AFIO_MAPR_TIM3_REMAP_FULLREMAP_Pos) /*!< 0x00000C00 */ +#define AFIO_MAPR_TIM3_REMAP_FULLREMAP AFIO_MAPR_TIM3_REMAP_FULLREMAP_Msk /*!< Full remap (CH1/PC6, CH2/PC7, CH3/PC8, CH4/PC9) */ + + +#define AFIO_MAPR_CAN_REMAP_Pos (13U) +#define AFIO_MAPR_CAN_REMAP_Msk (0x3UL << AFIO_MAPR_CAN_REMAP_Pos) /*!< 0x00006000 */ +#define AFIO_MAPR_CAN_REMAP AFIO_MAPR_CAN_REMAP_Msk /*!< CAN_REMAP[1:0] bits (CAN Alternate function remapping) */ +#define AFIO_MAPR_CAN_REMAP_0 (0x1UL << AFIO_MAPR_CAN_REMAP_Pos) /*!< 0x00002000 */ +#define AFIO_MAPR_CAN_REMAP_1 (0x2UL << AFIO_MAPR_CAN_REMAP_Pos) /*!< 0x00004000 */ + +/*!< CAN_REMAP configuration */ +#define AFIO_MAPR_CAN_REMAP_REMAP1 0x00000000U /*!< CANRX mapped to PA11, CANTX mapped to PA12 */ +#define AFIO_MAPR_CAN_REMAP_REMAP2_Pos (14U) +#define AFIO_MAPR_CAN_REMAP_REMAP2_Msk (0x1UL << AFIO_MAPR_CAN_REMAP_REMAP2_Pos) /*!< 0x00004000 */ +#define AFIO_MAPR_CAN_REMAP_REMAP2 AFIO_MAPR_CAN_REMAP_REMAP2_Msk /*!< CANRX mapped to PB8, CANTX mapped to PB9 */ +#define AFIO_MAPR_CAN_REMAP_REMAP3_Pos (13U) +#define AFIO_MAPR_CAN_REMAP_REMAP3_Msk (0x3UL << AFIO_MAPR_CAN_REMAP_REMAP3_Pos) /*!< 0x00006000 */ +#define AFIO_MAPR_CAN_REMAP_REMAP3 AFIO_MAPR_CAN_REMAP_REMAP3_Msk /*!< CANRX mapped to PD0, CANTX mapped to PD1 */ + +#define AFIO_MAPR_PD01_REMAP_Pos (15U) +#define AFIO_MAPR_PD01_REMAP_Msk (0x1UL << AFIO_MAPR_PD01_REMAP_Pos) /*!< 0x00008000 */ +#define AFIO_MAPR_PD01_REMAP AFIO_MAPR_PD01_REMAP_Msk /*!< Port D0/Port D1 mapping on OSC_IN/OSC_OUT */ + +/*!< SWJ_CFG configuration */ +#define AFIO_MAPR_SWJ_CFG_Pos (24U) +#define AFIO_MAPR_SWJ_CFG_Msk (0x7UL << AFIO_MAPR_SWJ_CFG_Pos) /*!< 0x07000000 */ +#define AFIO_MAPR_SWJ_CFG AFIO_MAPR_SWJ_CFG_Msk /*!< SWJ_CFG[2:0] bits (Serial Wire JTAG configuration) */ +#define AFIO_MAPR_SWJ_CFG_0 (0x1UL << AFIO_MAPR_SWJ_CFG_Pos) /*!< 0x01000000 */ +#define AFIO_MAPR_SWJ_CFG_1 (0x2UL << AFIO_MAPR_SWJ_CFG_Pos) /*!< 0x02000000 */ +#define AFIO_MAPR_SWJ_CFG_2 (0x4UL << AFIO_MAPR_SWJ_CFG_Pos) /*!< 0x04000000 */ + +#define AFIO_MAPR_SWJ_CFG_RESET 0x00000000U /*!< Full SWJ (JTAG-DP + SW-DP) : Reset State */ +#define AFIO_MAPR_SWJ_CFG_NOJNTRST_Pos (24U) +#define AFIO_MAPR_SWJ_CFG_NOJNTRST_Msk (0x1UL << AFIO_MAPR_SWJ_CFG_NOJNTRST_Pos) /*!< 0x01000000 */ +#define AFIO_MAPR_SWJ_CFG_NOJNTRST AFIO_MAPR_SWJ_CFG_NOJNTRST_Msk /*!< Full SWJ (JTAG-DP + SW-DP) but without JNTRST */ +#define AFIO_MAPR_SWJ_CFG_JTAGDISABLE_Pos (25U) +#define AFIO_MAPR_SWJ_CFG_JTAGDISABLE_Msk (0x1UL << AFIO_MAPR_SWJ_CFG_JTAGDISABLE_Pos) /*!< 0x02000000 */ +#define AFIO_MAPR_SWJ_CFG_JTAGDISABLE AFIO_MAPR_SWJ_CFG_JTAGDISABLE_Msk /*!< JTAG-DP Disabled and SW-DP Enabled */ +#define AFIO_MAPR_SWJ_CFG_DISABLE_Pos (26U) +#define AFIO_MAPR_SWJ_CFG_DISABLE_Msk (0x1UL << AFIO_MAPR_SWJ_CFG_DISABLE_Pos) /*!< 0x04000000 */ +#define AFIO_MAPR_SWJ_CFG_DISABLE AFIO_MAPR_SWJ_CFG_DISABLE_Msk /*!< JTAG-DP Disabled and SW-DP Disabled */ + + +/***************** Bit definition for AFIO_EXTICR1 register *****************/ +#define AFIO_EXTICR1_EXTI0_Pos (0U) +#define AFIO_EXTICR1_EXTI0_Msk (0xFUL << AFIO_EXTICR1_EXTI0_Pos) /*!< 0x0000000F */ +#define AFIO_EXTICR1_EXTI0 AFIO_EXTICR1_EXTI0_Msk /*!< EXTI 0 configuration */ +#define AFIO_EXTICR1_EXTI1_Pos (4U) +#define AFIO_EXTICR1_EXTI1_Msk (0xFUL << AFIO_EXTICR1_EXTI1_Pos) /*!< 0x000000F0 */ +#define AFIO_EXTICR1_EXTI1 AFIO_EXTICR1_EXTI1_Msk /*!< EXTI 1 configuration */ +#define AFIO_EXTICR1_EXTI2_Pos (8U) +#define AFIO_EXTICR1_EXTI2_Msk (0xFUL << AFIO_EXTICR1_EXTI2_Pos) /*!< 0x00000F00 */ +#define AFIO_EXTICR1_EXTI2 AFIO_EXTICR1_EXTI2_Msk /*!< EXTI 2 configuration */ +#define AFIO_EXTICR1_EXTI3_Pos (12U) +#define AFIO_EXTICR1_EXTI3_Msk (0xFUL << AFIO_EXTICR1_EXTI3_Pos) /*!< 0x0000F000 */ +#define AFIO_EXTICR1_EXTI3 AFIO_EXTICR1_EXTI3_Msk /*!< EXTI 3 configuration */ + +/*!< EXTI0 configuration */ +#define AFIO_EXTICR1_EXTI0_PA 0x00000000U /*!< PA[0] pin */ +#define AFIO_EXTICR1_EXTI0_PB_Pos (0U) +#define AFIO_EXTICR1_EXTI0_PB_Msk (0x1UL << AFIO_EXTICR1_EXTI0_PB_Pos) /*!< 0x00000001 */ +#define AFIO_EXTICR1_EXTI0_PB AFIO_EXTICR1_EXTI0_PB_Msk /*!< PB[0] pin */ +#define AFIO_EXTICR1_EXTI0_PC_Pos (1U) +#define AFIO_EXTICR1_EXTI0_PC_Msk (0x1UL << AFIO_EXTICR1_EXTI0_PC_Pos) /*!< 0x00000002 */ +#define AFIO_EXTICR1_EXTI0_PC AFIO_EXTICR1_EXTI0_PC_Msk /*!< PC[0] pin */ +#define AFIO_EXTICR1_EXTI0_PD_Pos (0U) +#define AFIO_EXTICR1_EXTI0_PD_Msk (0x3UL << AFIO_EXTICR1_EXTI0_PD_Pos) /*!< 0x00000003 */ +#define AFIO_EXTICR1_EXTI0_PD AFIO_EXTICR1_EXTI0_PD_Msk /*!< PD[0] pin */ +#define AFIO_EXTICR1_EXTI0_PE_Pos (2U) +#define AFIO_EXTICR1_EXTI0_PE_Msk (0x1UL << AFIO_EXTICR1_EXTI0_PE_Pos) /*!< 0x00000004 */ +#define AFIO_EXTICR1_EXTI0_PE AFIO_EXTICR1_EXTI0_PE_Msk /*!< PE[0] pin */ +#define AFIO_EXTICR1_EXTI0_PF_Pos (0U) +#define AFIO_EXTICR1_EXTI0_PF_Msk (0x5UL << AFIO_EXTICR1_EXTI0_PF_Pos) /*!< 0x00000005 */ +#define AFIO_EXTICR1_EXTI0_PF AFIO_EXTICR1_EXTI0_PF_Msk /*!< PF[0] pin */ +#define AFIO_EXTICR1_EXTI0_PG_Pos (1U) +#define AFIO_EXTICR1_EXTI0_PG_Msk (0x3UL << AFIO_EXTICR1_EXTI0_PG_Pos) /*!< 0x00000006 */ +#define AFIO_EXTICR1_EXTI0_PG AFIO_EXTICR1_EXTI0_PG_Msk /*!< PG[0] pin */ + +/*!< EXTI1 configuration */ +#define AFIO_EXTICR1_EXTI1_PA 0x00000000U /*!< PA[1] pin */ +#define AFIO_EXTICR1_EXTI1_PB_Pos (4U) +#define AFIO_EXTICR1_EXTI1_PB_Msk (0x1UL << AFIO_EXTICR1_EXTI1_PB_Pos) /*!< 0x00000010 */ +#define AFIO_EXTICR1_EXTI1_PB AFIO_EXTICR1_EXTI1_PB_Msk /*!< PB[1] pin */ +#define AFIO_EXTICR1_EXTI1_PC_Pos (5U) +#define AFIO_EXTICR1_EXTI1_PC_Msk (0x1UL << AFIO_EXTICR1_EXTI1_PC_Pos) /*!< 0x00000020 */ +#define AFIO_EXTICR1_EXTI1_PC AFIO_EXTICR1_EXTI1_PC_Msk /*!< PC[1] pin */ +#define AFIO_EXTICR1_EXTI1_PD_Pos (4U) +#define AFIO_EXTICR1_EXTI1_PD_Msk (0x3UL << AFIO_EXTICR1_EXTI1_PD_Pos) /*!< 0x00000030 */ +#define AFIO_EXTICR1_EXTI1_PD AFIO_EXTICR1_EXTI1_PD_Msk /*!< PD[1] pin */ +#define AFIO_EXTICR1_EXTI1_PE_Pos (6U) +#define AFIO_EXTICR1_EXTI1_PE_Msk (0x1UL << AFIO_EXTICR1_EXTI1_PE_Pos) /*!< 0x00000040 */ +#define AFIO_EXTICR1_EXTI1_PE AFIO_EXTICR1_EXTI1_PE_Msk /*!< PE[1] pin */ +#define AFIO_EXTICR1_EXTI1_PF_Pos (4U) +#define AFIO_EXTICR1_EXTI1_PF_Msk (0x5UL << AFIO_EXTICR1_EXTI1_PF_Pos) /*!< 0x00000050 */ +#define AFIO_EXTICR1_EXTI1_PF AFIO_EXTICR1_EXTI1_PF_Msk /*!< PF[1] pin */ +#define AFIO_EXTICR1_EXTI1_PG_Pos (5U) +#define AFIO_EXTICR1_EXTI1_PG_Msk (0x3UL << AFIO_EXTICR1_EXTI1_PG_Pos) /*!< 0x00000060 */ +#define AFIO_EXTICR1_EXTI1_PG AFIO_EXTICR1_EXTI1_PG_Msk /*!< PG[1] pin */ + +/*!< EXTI2 configuration */ +#define AFIO_EXTICR1_EXTI2_PA 0x00000000U /*!< PA[2] pin */ +#define AFIO_EXTICR1_EXTI2_PB_Pos (8U) +#define AFIO_EXTICR1_EXTI2_PB_Msk (0x1UL << AFIO_EXTICR1_EXTI2_PB_Pos) /*!< 0x00000100 */ +#define AFIO_EXTICR1_EXTI2_PB AFIO_EXTICR1_EXTI2_PB_Msk /*!< PB[2] pin */ +#define AFIO_EXTICR1_EXTI2_PC_Pos (9U) +#define AFIO_EXTICR1_EXTI2_PC_Msk (0x1UL << AFIO_EXTICR1_EXTI2_PC_Pos) /*!< 0x00000200 */ +#define AFIO_EXTICR1_EXTI2_PC AFIO_EXTICR1_EXTI2_PC_Msk /*!< PC[2] pin */ +#define AFIO_EXTICR1_EXTI2_PD_Pos (8U) +#define AFIO_EXTICR1_EXTI2_PD_Msk (0x3UL << AFIO_EXTICR1_EXTI2_PD_Pos) /*!< 0x00000300 */ +#define AFIO_EXTICR1_EXTI2_PD AFIO_EXTICR1_EXTI2_PD_Msk /*!< PD[2] pin */ +#define AFIO_EXTICR1_EXTI2_PE_Pos (10U) +#define AFIO_EXTICR1_EXTI2_PE_Msk (0x1UL << AFIO_EXTICR1_EXTI2_PE_Pos) /*!< 0x00000400 */ +#define AFIO_EXTICR1_EXTI2_PE AFIO_EXTICR1_EXTI2_PE_Msk /*!< PE[2] pin */ +#define AFIO_EXTICR1_EXTI2_PF_Pos (8U) +#define AFIO_EXTICR1_EXTI2_PF_Msk (0x5UL << AFIO_EXTICR1_EXTI2_PF_Pos) /*!< 0x00000500 */ +#define AFIO_EXTICR1_EXTI2_PF AFIO_EXTICR1_EXTI2_PF_Msk /*!< PF[2] pin */ +#define AFIO_EXTICR1_EXTI2_PG_Pos (9U) +#define AFIO_EXTICR1_EXTI2_PG_Msk (0x3UL << AFIO_EXTICR1_EXTI2_PG_Pos) /*!< 0x00000600 */ +#define AFIO_EXTICR1_EXTI2_PG AFIO_EXTICR1_EXTI2_PG_Msk /*!< PG[2] pin */ + +/*!< EXTI3 configuration */ +#define AFIO_EXTICR1_EXTI3_PA 0x00000000U /*!< PA[3] pin */ +#define AFIO_EXTICR1_EXTI3_PB_Pos (12U) +#define AFIO_EXTICR1_EXTI3_PB_Msk (0x1UL << AFIO_EXTICR1_EXTI3_PB_Pos) /*!< 0x00001000 */ +#define AFIO_EXTICR1_EXTI3_PB AFIO_EXTICR1_EXTI3_PB_Msk /*!< PB[3] pin */ +#define AFIO_EXTICR1_EXTI3_PC_Pos (13U) +#define AFIO_EXTICR1_EXTI3_PC_Msk (0x1UL << AFIO_EXTICR1_EXTI3_PC_Pos) /*!< 0x00002000 */ +#define AFIO_EXTICR1_EXTI3_PC AFIO_EXTICR1_EXTI3_PC_Msk /*!< PC[3] pin */ +#define AFIO_EXTICR1_EXTI3_PD_Pos (12U) +#define AFIO_EXTICR1_EXTI3_PD_Msk (0x3UL << AFIO_EXTICR1_EXTI3_PD_Pos) /*!< 0x00003000 */ +#define AFIO_EXTICR1_EXTI3_PD AFIO_EXTICR1_EXTI3_PD_Msk /*!< PD[3] pin */ +#define AFIO_EXTICR1_EXTI3_PE_Pos (14U) +#define AFIO_EXTICR1_EXTI3_PE_Msk (0x1UL << AFIO_EXTICR1_EXTI3_PE_Pos) /*!< 0x00004000 */ +#define AFIO_EXTICR1_EXTI3_PE AFIO_EXTICR1_EXTI3_PE_Msk /*!< PE[3] pin */ +#define AFIO_EXTICR1_EXTI3_PF_Pos (12U) +#define AFIO_EXTICR1_EXTI3_PF_Msk (0x5UL << AFIO_EXTICR1_EXTI3_PF_Pos) /*!< 0x00005000 */ +#define AFIO_EXTICR1_EXTI3_PF AFIO_EXTICR1_EXTI3_PF_Msk /*!< PF[3] pin */ +#define AFIO_EXTICR1_EXTI3_PG_Pos (13U) +#define AFIO_EXTICR1_EXTI3_PG_Msk (0x3UL << AFIO_EXTICR1_EXTI3_PG_Pos) /*!< 0x00006000 */ +#define AFIO_EXTICR1_EXTI3_PG AFIO_EXTICR1_EXTI3_PG_Msk /*!< PG[3] pin */ + +/***************** Bit definition for AFIO_EXTICR2 register *****************/ +#define AFIO_EXTICR2_EXTI4_Pos (0U) +#define AFIO_EXTICR2_EXTI4_Msk (0xFUL << AFIO_EXTICR2_EXTI4_Pos) /*!< 0x0000000F */ +#define AFIO_EXTICR2_EXTI4 AFIO_EXTICR2_EXTI4_Msk /*!< EXTI 4 configuration */ +#define AFIO_EXTICR2_EXTI5_Pos (4U) +#define AFIO_EXTICR2_EXTI5_Msk (0xFUL << AFIO_EXTICR2_EXTI5_Pos) /*!< 0x000000F0 */ +#define AFIO_EXTICR2_EXTI5 AFIO_EXTICR2_EXTI5_Msk /*!< EXTI 5 configuration */ +#define AFIO_EXTICR2_EXTI6_Pos (8U) +#define AFIO_EXTICR2_EXTI6_Msk (0xFUL << AFIO_EXTICR2_EXTI6_Pos) /*!< 0x00000F00 */ +#define AFIO_EXTICR2_EXTI6 AFIO_EXTICR2_EXTI6_Msk /*!< EXTI 6 configuration */ +#define AFIO_EXTICR2_EXTI7_Pos (12U) +#define AFIO_EXTICR2_EXTI7_Msk (0xFUL << AFIO_EXTICR2_EXTI7_Pos) /*!< 0x0000F000 */ +#define AFIO_EXTICR2_EXTI7 AFIO_EXTICR2_EXTI7_Msk /*!< EXTI 7 configuration */ + +/*!< EXTI4 configuration */ +#define AFIO_EXTICR2_EXTI4_PA 0x00000000U /*!< PA[4] pin */ +#define AFIO_EXTICR2_EXTI4_PB_Pos (0U) +#define AFIO_EXTICR2_EXTI4_PB_Msk (0x1UL << AFIO_EXTICR2_EXTI4_PB_Pos) /*!< 0x00000001 */ +#define AFIO_EXTICR2_EXTI4_PB AFIO_EXTICR2_EXTI4_PB_Msk /*!< PB[4] pin */ +#define AFIO_EXTICR2_EXTI4_PC_Pos (1U) +#define AFIO_EXTICR2_EXTI4_PC_Msk (0x1UL << AFIO_EXTICR2_EXTI4_PC_Pos) /*!< 0x00000002 */ +#define AFIO_EXTICR2_EXTI4_PC AFIO_EXTICR2_EXTI4_PC_Msk /*!< PC[4] pin */ +#define AFIO_EXTICR2_EXTI4_PD_Pos (0U) +#define AFIO_EXTICR2_EXTI4_PD_Msk (0x3UL << AFIO_EXTICR2_EXTI4_PD_Pos) /*!< 0x00000003 */ +#define AFIO_EXTICR2_EXTI4_PD AFIO_EXTICR2_EXTI4_PD_Msk /*!< PD[4] pin */ +#define AFIO_EXTICR2_EXTI4_PE_Pos (2U) +#define AFIO_EXTICR2_EXTI4_PE_Msk (0x1UL << AFIO_EXTICR2_EXTI4_PE_Pos) /*!< 0x00000004 */ +#define AFIO_EXTICR2_EXTI4_PE AFIO_EXTICR2_EXTI4_PE_Msk /*!< PE[4] pin */ +#define AFIO_EXTICR2_EXTI4_PF_Pos (0U) +#define AFIO_EXTICR2_EXTI4_PF_Msk (0x5UL << AFIO_EXTICR2_EXTI4_PF_Pos) /*!< 0x00000005 */ +#define AFIO_EXTICR2_EXTI4_PF AFIO_EXTICR2_EXTI4_PF_Msk /*!< PF[4] pin */ +#define AFIO_EXTICR2_EXTI4_PG_Pos (1U) +#define AFIO_EXTICR2_EXTI4_PG_Msk (0x3UL << AFIO_EXTICR2_EXTI4_PG_Pos) /*!< 0x00000006 */ +#define AFIO_EXTICR2_EXTI4_PG AFIO_EXTICR2_EXTI4_PG_Msk /*!< PG[4] pin */ + +/* EXTI5 configuration */ +#define AFIO_EXTICR2_EXTI5_PA 0x00000000U /*!< PA[5] pin */ +#define AFIO_EXTICR2_EXTI5_PB_Pos (4U) +#define AFIO_EXTICR2_EXTI5_PB_Msk (0x1UL << AFIO_EXTICR2_EXTI5_PB_Pos) /*!< 0x00000010 */ +#define AFIO_EXTICR2_EXTI5_PB AFIO_EXTICR2_EXTI5_PB_Msk /*!< PB[5] pin */ +#define AFIO_EXTICR2_EXTI5_PC_Pos (5U) +#define AFIO_EXTICR2_EXTI5_PC_Msk (0x1UL << AFIO_EXTICR2_EXTI5_PC_Pos) /*!< 0x00000020 */ +#define AFIO_EXTICR2_EXTI5_PC AFIO_EXTICR2_EXTI5_PC_Msk /*!< PC[5] pin */ +#define AFIO_EXTICR2_EXTI5_PD_Pos (4U) +#define AFIO_EXTICR2_EXTI5_PD_Msk (0x3UL << AFIO_EXTICR2_EXTI5_PD_Pos) /*!< 0x00000030 */ +#define AFIO_EXTICR2_EXTI5_PD AFIO_EXTICR2_EXTI5_PD_Msk /*!< PD[5] pin */ +#define AFIO_EXTICR2_EXTI5_PE_Pos (6U) +#define AFIO_EXTICR2_EXTI5_PE_Msk (0x1UL << AFIO_EXTICR2_EXTI5_PE_Pos) /*!< 0x00000040 */ +#define AFIO_EXTICR2_EXTI5_PE AFIO_EXTICR2_EXTI5_PE_Msk /*!< PE[5] pin */ +#define AFIO_EXTICR2_EXTI5_PF_Pos (4U) +#define AFIO_EXTICR2_EXTI5_PF_Msk (0x5UL << AFIO_EXTICR2_EXTI5_PF_Pos) /*!< 0x00000050 */ +#define AFIO_EXTICR2_EXTI5_PF AFIO_EXTICR2_EXTI5_PF_Msk /*!< PF[5] pin */ +#define AFIO_EXTICR2_EXTI5_PG_Pos (5U) +#define AFIO_EXTICR2_EXTI5_PG_Msk (0x3UL << AFIO_EXTICR2_EXTI5_PG_Pos) /*!< 0x00000060 */ +#define AFIO_EXTICR2_EXTI5_PG AFIO_EXTICR2_EXTI5_PG_Msk /*!< PG[5] pin */ + +/*!< EXTI6 configuration */ +#define AFIO_EXTICR2_EXTI6_PA 0x00000000U /*!< PA[6] pin */ +#define AFIO_EXTICR2_EXTI6_PB_Pos (8U) +#define AFIO_EXTICR2_EXTI6_PB_Msk (0x1UL << AFIO_EXTICR2_EXTI6_PB_Pos) /*!< 0x00000100 */ +#define AFIO_EXTICR2_EXTI6_PB AFIO_EXTICR2_EXTI6_PB_Msk /*!< PB[6] pin */ +#define AFIO_EXTICR2_EXTI6_PC_Pos (9U) +#define AFIO_EXTICR2_EXTI6_PC_Msk (0x1UL << AFIO_EXTICR2_EXTI6_PC_Pos) /*!< 0x00000200 */ +#define AFIO_EXTICR2_EXTI6_PC AFIO_EXTICR2_EXTI6_PC_Msk /*!< PC[6] pin */ +#define AFIO_EXTICR2_EXTI6_PD_Pos (8U) +#define AFIO_EXTICR2_EXTI6_PD_Msk (0x3UL << AFIO_EXTICR2_EXTI6_PD_Pos) /*!< 0x00000300 */ +#define AFIO_EXTICR2_EXTI6_PD AFIO_EXTICR2_EXTI6_PD_Msk /*!< PD[6] pin */ +#define AFIO_EXTICR2_EXTI6_PE_Pos (10U) +#define AFIO_EXTICR2_EXTI6_PE_Msk (0x1UL << AFIO_EXTICR2_EXTI6_PE_Pos) /*!< 0x00000400 */ +#define AFIO_EXTICR2_EXTI6_PE AFIO_EXTICR2_EXTI6_PE_Msk /*!< PE[6] pin */ +#define AFIO_EXTICR2_EXTI6_PF_Pos (8U) +#define AFIO_EXTICR2_EXTI6_PF_Msk (0x5UL << AFIO_EXTICR2_EXTI6_PF_Pos) /*!< 0x00000500 */ +#define AFIO_EXTICR2_EXTI6_PF AFIO_EXTICR2_EXTI6_PF_Msk /*!< PF[6] pin */ +#define AFIO_EXTICR2_EXTI6_PG_Pos (9U) +#define AFIO_EXTICR2_EXTI6_PG_Msk (0x3UL << AFIO_EXTICR2_EXTI6_PG_Pos) /*!< 0x00000600 */ +#define AFIO_EXTICR2_EXTI6_PG AFIO_EXTICR2_EXTI6_PG_Msk /*!< PG[6] pin */ + +/*!< EXTI7 configuration */ +#define AFIO_EXTICR2_EXTI7_PA 0x00000000U /*!< PA[7] pin */ +#define AFIO_EXTICR2_EXTI7_PB_Pos (12U) +#define AFIO_EXTICR2_EXTI7_PB_Msk (0x1UL << AFIO_EXTICR2_EXTI7_PB_Pos) /*!< 0x00001000 */ +#define AFIO_EXTICR2_EXTI7_PB AFIO_EXTICR2_EXTI7_PB_Msk /*!< PB[7] pin */ +#define AFIO_EXTICR2_EXTI7_PC_Pos (13U) +#define AFIO_EXTICR2_EXTI7_PC_Msk (0x1UL << AFIO_EXTICR2_EXTI7_PC_Pos) /*!< 0x00002000 */ +#define AFIO_EXTICR2_EXTI7_PC AFIO_EXTICR2_EXTI7_PC_Msk /*!< PC[7] pin */ +#define AFIO_EXTICR2_EXTI7_PD_Pos (12U) +#define AFIO_EXTICR2_EXTI7_PD_Msk (0x3UL << AFIO_EXTICR2_EXTI7_PD_Pos) /*!< 0x00003000 */ +#define AFIO_EXTICR2_EXTI7_PD AFIO_EXTICR2_EXTI7_PD_Msk /*!< PD[7] pin */ +#define AFIO_EXTICR2_EXTI7_PE_Pos (14U) +#define AFIO_EXTICR2_EXTI7_PE_Msk (0x1UL << AFIO_EXTICR2_EXTI7_PE_Pos) /*!< 0x00004000 */ +#define AFIO_EXTICR2_EXTI7_PE AFIO_EXTICR2_EXTI7_PE_Msk /*!< PE[7] pin */ +#define AFIO_EXTICR2_EXTI7_PF_Pos (12U) +#define AFIO_EXTICR2_EXTI7_PF_Msk (0x5UL << AFIO_EXTICR2_EXTI7_PF_Pos) /*!< 0x00005000 */ +#define AFIO_EXTICR2_EXTI7_PF AFIO_EXTICR2_EXTI7_PF_Msk /*!< PF[7] pin */ +#define AFIO_EXTICR2_EXTI7_PG_Pos (13U) +#define AFIO_EXTICR2_EXTI7_PG_Msk (0x3UL << AFIO_EXTICR2_EXTI7_PG_Pos) /*!< 0x00006000 */ +#define AFIO_EXTICR2_EXTI7_PG AFIO_EXTICR2_EXTI7_PG_Msk /*!< PG[7] pin */ + +/***************** Bit definition for AFIO_EXTICR3 register *****************/ +#define AFIO_EXTICR3_EXTI8_Pos (0U) +#define AFIO_EXTICR3_EXTI8_Msk (0xFUL << AFIO_EXTICR3_EXTI8_Pos) /*!< 0x0000000F */ +#define AFIO_EXTICR3_EXTI8 AFIO_EXTICR3_EXTI8_Msk /*!< EXTI 8 configuration */ +#define AFIO_EXTICR3_EXTI9_Pos (4U) +#define AFIO_EXTICR3_EXTI9_Msk (0xFUL << AFIO_EXTICR3_EXTI9_Pos) /*!< 0x000000F0 */ +#define AFIO_EXTICR3_EXTI9 AFIO_EXTICR3_EXTI9_Msk /*!< EXTI 9 configuration */ +#define AFIO_EXTICR3_EXTI10_Pos (8U) +#define AFIO_EXTICR3_EXTI10_Msk (0xFUL << AFIO_EXTICR3_EXTI10_Pos) /*!< 0x00000F00 */ +#define AFIO_EXTICR3_EXTI10 AFIO_EXTICR3_EXTI10_Msk /*!< EXTI 10 configuration */ +#define AFIO_EXTICR3_EXTI11_Pos (12U) +#define AFIO_EXTICR3_EXTI11_Msk (0xFUL << AFIO_EXTICR3_EXTI11_Pos) /*!< 0x0000F000 */ +#define AFIO_EXTICR3_EXTI11 AFIO_EXTICR3_EXTI11_Msk /*!< EXTI 11 configuration */ + +/*!< EXTI8 configuration */ +#define AFIO_EXTICR3_EXTI8_PA 0x00000000U /*!< PA[8] pin */ +#define AFIO_EXTICR3_EXTI8_PB_Pos (0U) +#define AFIO_EXTICR3_EXTI8_PB_Msk (0x1UL << AFIO_EXTICR3_EXTI8_PB_Pos) /*!< 0x00000001 */ +#define AFIO_EXTICR3_EXTI8_PB AFIO_EXTICR3_EXTI8_PB_Msk /*!< PB[8] pin */ +#define AFIO_EXTICR3_EXTI8_PC_Pos (1U) +#define AFIO_EXTICR3_EXTI8_PC_Msk (0x1UL << AFIO_EXTICR3_EXTI8_PC_Pos) /*!< 0x00000002 */ +#define AFIO_EXTICR3_EXTI8_PC AFIO_EXTICR3_EXTI8_PC_Msk /*!< PC[8] pin */ +#define AFIO_EXTICR3_EXTI8_PD_Pos (0U) +#define AFIO_EXTICR3_EXTI8_PD_Msk (0x3UL << AFIO_EXTICR3_EXTI8_PD_Pos) /*!< 0x00000003 */ +#define AFIO_EXTICR3_EXTI8_PD AFIO_EXTICR3_EXTI8_PD_Msk /*!< PD[8] pin */ +#define AFIO_EXTICR3_EXTI8_PE_Pos (2U) +#define AFIO_EXTICR3_EXTI8_PE_Msk (0x1UL << AFIO_EXTICR3_EXTI8_PE_Pos) /*!< 0x00000004 */ +#define AFIO_EXTICR3_EXTI8_PE AFIO_EXTICR3_EXTI8_PE_Msk /*!< PE[8] pin */ +#define AFIO_EXTICR3_EXTI8_PF_Pos (0U) +#define AFIO_EXTICR3_EXTI8_PF_Msk (0x5UL << AFIO_EXTICR3_EXTI8_PF_Pos) /*!< 0x00000005 */ +#define AFIO_EXTICR3_EXTI8_PF AFIO_EXTICR3_EXTI8_PF_Msk /*!< PF[8] pin */ +#define AFIO_EXTICR3_EXTI8_PG_Pos (1U) +#define AFIO_EXTICR3_EXTI8_PG_Msk (0x3UL << AFIO_EXTICR3_EXTI8_PG_Pos) /*!< 0x00000006 */ +#define AFIO_EXTICR3_EXTI8_PG AFIO_EXTICR3_EXTI8_PG_Msk /*!< PG[8] pin */ + +/*!< EXTI9 configuration */ +#define AFIO_EXTICR3_EXTI9_PA 0x00000000U /*!< PA[9] pin */ +#define AFIO_EXTICR3_EXTI9_PB_Pos (4U) +#define AFIO_EXTICR3_EXTI9_PB_Msk (0x1UL << AFIO_EXTICR3_EXTI9_PB_Pos) /*!< 0x00000010 */ +#define AFIO_EXTICR3_EXTI9_PB AFIO_EXTICR3_EXTI9_PB_Msk /*!< PB[9] pin */ +#define AFIO_EXTICR3_EXTI9_PC_Pos (5U) +#define AFIO_EXTICR3_EXTI9_PC_Msk (0x1UL << AFIO_EXTICR3_EXTI9_PC_Pos) /*!< 0x00000020 */ +#define AFIO_EXTICR3_EXTI9_PC AFIO_EXTICR3_EXTI9_PC_Msk /*!< PC[9] pin */ +#define AFIO_EXTICR3_EXTI9_PD_Pos (4U) +#define AFIO_EXTICR3_EXTI9_PD_Msk (0x3UL << AFIO_EXTICR3_EXTI9_PD_Pos) /*!< 0x00000030 */ +#define AFIO_EXTICR3_EXTI9_PD AFIO_EXTICR3_EXTI9_PD_Msk /*!< PD[9] pin */ +#define AFIO_EXTICR3_EXTI9_PE_Pos (6U) +#define AFIO_EXTICR3_EXTI9_PE_Msk (0x1UL << AFIO_EXTICR3_EXTI9_PE_Pos) /*!< 0x00000040 */ +#define AFIO_EXTICR3_EXTI9_PE AFIO_EXTICR3_EXTI9_PE_Msk /*!< PE[9] pin */ +#define AFIO_EXTICR3_EXTI9_PF_Pos (4U) +#define AFIO_EXTICR3_EXTI9_PF_Msk (0x5UL << AFIO_EXTICR3_EXTI9_PF_Pos) /*!< 0x00000050 */ +#define AFIO_EXTICR3_EXTI9_PF AFIO_EXTICR3_EXTI9_PF_Msk /*!< PF[9] pin */ +#define AFIO_EXTICR3_EXTI9_PG_Pos (5U) +#define AFIO_EXTICR3_EXTI9_PG_Msk (0x3UL << AFIO_EXTICR3_EXTI9_PG_Pos) /*!< 0x00000060 */ +#define AFIO_EXTICR3_EXTI9_PG AFIO_EXTICR3_EXTI9_PG_Msk /*!< PG[9] pin */ + +/*!< EXTI10 configuration */ +#define AFIO_EXTICR3_EXTI10_PA 0x00000000U /*!< PA[10] pin */ +#define AFIO_EXTICR3_EXTI10_PB_Pos (8U) +#define AFIO_EXTICR3_EXTI10_PB_Msk (0x1UL << AFIO_EXTICR3_EXTI10_PB_Pos) /*!< 0x00000100 */ +#define AFIO_EXTICR3_EXTI10_PB AFIO_EXTICR3_EXTI10_PB_Msk /*!< PB[10] pin */ +#define AFIO_EXTICR3_EXTI10_PC_Pos (9U) +#define AFIO_EXTICR3_EXTI10_PC_Msk (0x1UL << AFIO_EXTICR3_EXTI10_PC_Pos) /*!< 0x00000200 */ +#define AFIO_EXTICR3_EXTI10_PC AFIO_EXTICR3_EXTI10_PC_Msk /*!< PC[10] pin */ +#define AFIO_EXTICR3_EXTI10_PD_Pos (8U) +#define AFIO_EXTICR3_EXTI10_PD_Msk (0x3UL << AFIO_EXTICR3_EXTI10_PD_Pos) /*!< 0x00000300 */ +#define AFIO_EXTICR3_EXTI10_PD AFIO_EXTICR3_EXTI10_PD_Msk /*!< PD[10] pin */ +#define AFIO_EXTICR3_EXTI10_PE_Pos (10U) +#define AFIO_EXTICR3_EXTI10_PE_Msk (0x1UL << AFIO_EXTICR3_EXTI10_PE_Pos) /*!< 0x00000400 */ +#define AFIO_EXTICR3_EXTI10_PE AFIO_EXTICR3_EXTI10_PE_Msk /*!< PE[10] pin */ +#define AFIO_EXTICR3_EXTI10_PF_Pos (8U) +#define AFIO_EXTICR3_EXTI10_PF_Msk (0x5UL << AFIO_EXTICR3_EXTI10_PF_Pos) /*!< 0x00000500 */ +#define AFIO_EXTICR3_EXTI10_PF AFIO_EXTICR3_EXTI10_PF_Msk /*!< PF[10] pin */ +#define AFIO_EXTICR3_EXTI10_PG_Pos (9U) +#define AFIO_EXTICR3_EXTI10_PG_Msk (0x3UL << AFIO_EXTICR3_EXTI10_PG_Pos) /*!< 0x00000600 */ +#define AFIO_EXTICR3_EXTI10_PG AFIO_EXTICR3_EXTI10_PG_Msk /*!< PG[10] pin */ + +/*!< EXTI11 configuration */ +#define AFIO_EXTICR3_EXTI11_PA 0x00000000U /*!< PA[11] pin */ +#define AFIO_EXTICR3_EXTI11_PB_Pos (12U) +#define AFIO_EXTICR3_EXTI11_PB_Msk (0x1UL << AFIO_EXTICR3_EXTI11_PB_Pos) /*!< 0x00001000 */ +#define AFIO_EXTICR3_EXTI11_PB AFIO_EXTICR3_EXTI11_PB_Msk /*!< PB[11] pin */ +#define AFIO_EXTICR3_EXTI11_PC_Pos (13U) +#define AFIO_EXTICR3_EXTI11_PC_Msk (0x1UL << AFIO_EXTICR3_EXTI11_PC_Pos) /*!< 0x00002000 */ +#define AFIO_EXTICR3_EXTI11_PC AFIO_EXTICR3_EXTI11_PC_Msk /*!< PC[11] pin */ +#define AFIO_EXTICR3_EXTI11_PD_Pos (12U) +#define AFIO_EXTICR3_EXTI11_PD_Msk (0x3UL << AFIO_EXTICR3_EXTI11_PD_Pos) /*!< 0x00003000 */ +#define AFIO_EXTICR3_EXTI11_PD AFIO_EXTICR3_EXTI11_PD_Msk /*!< PD[11] pin */ +#define AFIO_EXTICR3_EXTI11_PE_Pos (14U) +#define AFIO_EXTICR3_EXTI11_PE_Msk (0x1UL << AFIO_EXTICR3_EXTI11_PE_Pos) /*!< 0x00004000 */ +#define AFIO_EXTICR3_EXTI11_PE AFIO_EXTICR3_EXTI11_PE_Msk /*!< PE[11] pin */ +#define AFIO_EXTICR3_EXTI11_PF_Pos (12U) +#define AFIO_EXTICR3_EXTI11_PF_Msk (0x5UL << AFIO_EXTICR3_EXTI11_PF_Pos) /*!< 0x00005000 */ +#define AFIO_EXTICR3_EXTI11_PF AFIO_EXTICR3_EXTI11_PF_Msk /*!< PF[11] pin */ +#define AFIO_EXTICR3_EXTI11_PG_Pos (13U) +#define AFIO_EXTICR3_EXTI11_PG_Msk (0x3UL << AFIO_EXTICR3_EXTI11_PG_Pos) /*!< 0x00006000 */ +#define AFIO_EXTICR3_EXTI11_PG AFIO_EXTICR3_EXTI11_PG_Msk /*!< PG[11] pin */ + +/***************** Bit definition for AFIO_EXTICR4 register *****************/ +#define AFIO_EXTICR4_EXTI12_Pos (0U) +#define AFIO_EXTICR4_EXTI12_Msk (0xFUL << AFIO_EXTICR4_EXTI12_Pos) /*!< 0x0000000F */ +#define AFIO_EXTICR4_EXTI12 AFIO_EXTICR4_EXTI12_Msk /*!< EXTI 12 configuration */ +#define AFIO_EXTICR4_EXTI13_Pos (4U) +#define AFIO_EXTICR4_EXTI13_Msk (0xFUL << AFIO_EXTICR4_EXTI13_Pos) /*!< 0x000000F0 */ +#define AFIO_EXTICR4_EXTI13 AFIO_EXTICR4_EXTI13_Msk /*!< EXTI 13 configuration */ +#define AFIO_EXTICR4_EXTI14_Pos (8U) +#define AFIO_EXTICR4_EXTI14_Msk (0xFUL << AFIO_EXTICR4_EXTI14_Pos) /*!< 0x00000F00 */ +#define AFIO_EXTICR4_EXTI14 AFIO_EXTICR4_EXTI14_Msk /*!< EXTI 14 configuration */ +#define AFIO_EXTICR4_EXTI15_Pos (12U) +#define AFIO_EXTICR4_EXTI15_Msk (0xFUL << AFIO_EXTICR4_EXTI15_Pos) /*!< 0x0000F000 */ +#define AFIO_EXTICR4_EXTI15 AFIO_EXTICR4_EXTI15_Msk /*!< EXTI 15 configuration */ + +/* EXTI12 configuration */ +#define AFIO_EXTICR4_EXTI12_PA 0x00000000U /*!< PA[12] pin */ +#define AFIO_EXTICR4_EXTI12_PB_Pos (0U) +#define AFIO_EXTICR4_EXTI12_PB_Msk (0x1UL << AFIO_EXTICR4_EXTI12_PB_Pos) /*!< 0x00000001 */ +#define AFIO_EXTICR4_EXTI12_PB AFIO_EXTICR4_EXTI12_PB_Msk /*!< PB[12] pin */ +#define AFIO_EXTICR4_EXTI12_PC_Pos (1U) +#define AFIO_EXTICR4_EXTI12_PC_Msk (0x1UL << AFIO_EXTICR4_EXTI12_PC_Pos) /*!< 0x00000002 */ +#define AFIO_EXTICR4_EXTI12_PC AFIO_EXTICR4_EXTI12_PC_Msk /*!< PC[12] pin */ +#define AFIO_EXTICR4_EXTI12_PD_Pos (0U) +#define AFIO_EXTICR4_EXTI12_PD_Msk (0x3UL << AFIO_EXTICR4_EXTI12_PD_Pos) /*!< 0x00000003 */ +#define AFIO_EXTICR4_EXTI12_PD AFIO_EXTICR4_EXTI12_PD_Msk /*!< PD[12] pin */ +#define AFIO_EXTICR4_EXTI12_PE_Pos (2U) +#define AFIO_EXTICR4_EXTI12_PE_Msk (0x1UL << AFIO_EXTICR4_EXTI12_PE_Pos) /*!< 0x00000004 */ +#define AFIO_EXTICR4_EXTI12_PE AFIO_EXTICR4_EXTI12_PE_Msk /*!< PE[12] pin */ +#define AFIO_EXTICR4_EXTI12_PF_Pos (0U) +#define AFIO_EXTICR4_EXTI12_PF_Msk (0x5UL << AFIO_EXTICR4_EXTI12_PF_Pos) /*!< 0x00000005 */ +#define AFIO_EXTICR4_EXTI12_PF AFIO_EXTICR4_EXTI12_PF_Msk /*!< PF[12] pin */ +#define AFIO_EXTICR4_EXTI12_PG_Pos (1U) +#define AFIO_EXTICR4_EXTI12_PG_Msk (0x3UL << AFIO_EXTICR4_EXTI12_PG_Pos) /*!< 0x00000006 */ +#define AFIO_EXTICR4_EXTI12_PG AFIO_EXTICR4_EXTI12_PG_Msk /*!< PG[12] pin */ + +/* EXTI13 configuration */ +#define AFIO_EXTICR4_EXTI13_PA 0x00000000U /*!< PA[13] pin */ +#define AFIO_EXTICR4_EXTI13_PB_Pos (4U) +#define AFIO_EXTICR4_EXTI13_PB_Msk (0x1UL << AFIO_EXTICR4_EXTI13_PB_Pos) /*!< 0x00000010 */ +#define AFIO_EXTICR4_EXTI13_PB AFIO_EXTICR4_EXTI13_PB_Msk /*!< PB[13] pin */ +#define AFIO_EXTICR4_EXTI13_PC_Pos (5U) +#define AFIO_EXTICR4_EXTI13_PC_Msk (0x1UL << AFIO_EXTICR4_EXTI13_PC_Pos) /*!< 0x00000020 */ +#define AFIO_EXTICR4_EXTI13_PC AFIO_EXTICR4_EXTI13_PC_Msk /*!< PC[13] pin */ +#define AFIO_EXTICR4_EXTI13_PD_Pos (4U) +#define AFIO_EXTICR4_EXTI13_PD_Msk (0x3UL << AFIO_EXTICR4_EXTI13_PD_Pos) /*!< 0x00000030 */ +#define AFIO_EXTICR4_EXTI13_PD AFIO_EXTICR4_EXTI13_PD_Msk /*!< PD[13] pin */ +#define AFIO_EXTICR4_EXTI13_PE_Pos (6U) +#define AFIO_EXTICR4_EXTI13_PE_Msk (0x1UL << AFIO_EXTICR4_EXTI13_PE_Pos) /*!< 0x00000040 */ +#define AFIO_EXTICR4_EXTI13_PE AFIO_EXTICR4_EXTI13_PE_Msk /*!< PE[13] pin */ +#define AFIO_EXTICR4_EXTI13_PF_Pos (4U) +#define AFIO_EXTICR4_EXTI13_PF_Msk (0x5UL << AFIO_EXTICR4_EXTI13_PF_Pos) /*!< 0x00000050 */ +#define AFIO_EXTICR4_EXTI13_PF AFIO_EXTICR4_EXTI13_PF_Msk /*!< PF[13] pin */ +#define AFIO_EXTICR4_EXTI13_PG_Pos (5U) +#define AFIO_EXTICR4_EXTI13_PG_Msk (0x3UL << AFIO_EXTICR4_EXTI13_PG_Pos) /*!< 0x00000060 */ +#define AFIO_EXTICR4_EXTI13_PG AFIO_EXTICR4_EXTI13_PG_Msk /*!< PG[13] pin */ + +/*!< EXTI14 configuration */ +#define AFIO_EXTICR4_EXTI14_PA 0x00000000U /*!< PA[14] pin */ +#define AFIO_EXTICR4_EXTI14_PB_Pos (8U) +#define AFIO_EXTICR4_EXTI14_PB_Msk (0x1UL << AFIO_EXTICR4_EXTI14_PB_Pos) /*!< 0x00000100 */ +#define AFIO_EXTICR4_EXTI14_PB AFIO_EXTICR4_EXTI14_PB_Msk /*!< PB[14] pin */ +#define AFIO_EXTICR4_EXTI14_PC_Pos (9U) +#define AFIO_EXTICR4_EXTI14_PC_Msk (0x1UL << AFIO_EXTICR4_EXTI14_PC_Pos) /*!< 0x00000200 */ +#define AFIO_EXTICR4_EXTI14_PC AFIO_EXTICR4_EXTI14_PC_Msk /*!< PC[14] pin */ +#define AFIO_EXTICR4_EXTI14_PD_Pos (8U) +#define AFIO_EXTICR4_EXTI14_PD_Msk (0x3UL << AFIO_EXTICR4_EXTI14_PD_Pos) /*!< 0x00000300 */ +#define AFIO_EXTICR4_EXTI14_PD AFIO_EXTICR4_EXTI14_PD_Msk /*!< PD[14] pin */ +#define AFIO_EXTICR4_EXTI14_PE_Pos (10U) +#define AFIO_EXTICR4_EXTI14_PE_Msk (0x1UL << AFIO_EXTICR4_EXTI14_PE_Pos) /*!< 0x00000400 */ +#define AFIO_EXTICR4_EXTI14_PE AFIO_EXTICR4_EXTI14_PE_Msk /*!< PE[14] pin */ +#define AFIO_EXTICR4_EXTI14_PF_Pos (8U) +#define AFIO_EXTICR4_EXTI14_PF_Msk (0x5UL << AFIO_EXTICR4_EXTI14_PF_Pos) /*!< 0x00000500 */ +#define AFIO_EXTICR4_EXTI14_PF AFIO_EXTICR4_EXTI14_PF_Msk /*!< PF[14] pin */ +#define AFIO_EXTICR4_EXTI14_PG_Pos (9U) +#define AFIO_EXTICR4_EXTI14_PG_Msk (0x3UL << AFIO_EXTICR4_EXTI14_PG_Pos) /*!< 0x00000600 */ +#define AFIO_EXTICR4_EXTI14_PG AFIO_EXTICR4_EXTI14_PG_Msk /*!< PG[14] pin */ + +/*!< EXTI15 configuration */ +#define AFIO_EXTICR4_EXTI15_PA 0x00000000U /*!< PA[15] pin */ +#define AFIO_EXTICR4_EXTI15_PB_Pos (12U) +#define AFIO_EXTICR4_EXTI15_PB_Msk (0x1UL << AFIO_EXTICR4_EXTI15_PB_Pos) /*!< 0x00001000 */ +#define AFIO_EXTICR4_EXTI15_PB AFIO_EXTICR4_EXTI15_PB_Msk /*!< PB[15] pin */ +#define AFIO_EXTICR4_EXTI15_PC_Pos (13U) +#define AFIO_EXTICR4_EXTI15_PC_Msk (0x1UL << AFIO_EXTICR4_EXTI15_PC_Pos) /*!< 0x00002000 */ +#define AFIO_EXTICR4_EXTI15_PC AFIO_EXTICR4_EXTI15_PC_Msk /*!< PC[15] pin */ +#define AFIO_EXTICR4_EXTI15_PD_Pos (12U) +#define AFIO_EXTICR4_EXTI15_PD_Msk (0x3UL << AFIO_EXTICR4_EXTI15_PD_Pos) /*!< 0x00003000 */ +#define AFIO_EXTICR4_EXTI15_PD AFIO_EXTICR4_EXTI15_PD_Msk /*!< PD[15] pin */ +#define AFIO_EXTICR4_EXTI15_PE_Pos (14U) +#define AFIO_EXTICR4_EXTI15_PE_Msk (0x1UL << AFIO_EXTICR4_EXTI15_PE_Pos) /*!< 0x00004000 */ +#define AFIO_EXTICR4_EXTI15_PE AFIO_EXTICR4_EXTI15_PE_Msk /*!< PE[15] pin */ +#define AFIO_EXTICR4_EXTI15_PF_Pos (12U) +#define AFIO_EXTICR4_EXTI15_PF_Msk (0x5UL << AFIO_EXTICR4_EXTI15_PF_Pos) /*!< 0x00005000 */ +#define AFIO_EXTICR4_EXTI15_PF AFIO_EXTICR4_EXTI15_PF_Msk /*!< PF[15] pin */ +#define AFIO_EXTICR4_EXTI15_PG_Pos (13U) +#define AFIO_EXTICR4_EXTI15_PG_Msk (0x3UL << AFIO_EXTICR4_EXTI15_PG_Pos) /*!< 0x00006000 */ +#define AFIO_EXTICR4_EXTI15_PG AFIO_EXTICR4_EXTI15_PG_Msk /*!< PG[15] pin */ + +/****************** Bit definition for AFIO_MAPR2 register ******************/ + + + +/******************************************************************************/ +/* */ +/* External Interrupt/Event Controller */ +/* */ +/******************************************************************************/ + +/******************* Bit definition for EXTI_IMR register *******************/ +#define EXTI_IMR_MR0_Pos (0U) +#define EXTI_IMR_MR0_Msk (0x1UL << EXTI_IMR_MR0_Pos) /*!< 0x00000001 */ +#define EXTI_IMR_MR0 EXTI_IMR_MR0_Msk /*!< Interrupt Mask on line 0 */ +#define EXTI_IMR_MR1_Pos (1U) +#define EXTI_IMR_MR1_Msk (0x1UL << EXTI_IMR_MR1_Pos) /*!< 0x00000002 */ +#define EXTI_IMR_MR1 EXTI_IMR_MR1_Msk /*!< Interrupt Mask on line 1 */ +#define EXTI_IMR_MR2_Pos (2U) +#define EXTI_IMR_MR2_Msk (0x1UL << EXTI_IMR_MR2_Pos) /*!< 0x00000004 */ +#define EXTI_IMR_MR2 EXTI_IMR_MR2_Msk /*!< Interrupt Mask on line 2 */ +#define EXTI_IMR_MR3_Pos (3U) +#define EXTI_IMR_MR3_Msk (0x1UL << EXTI_IMR_MR3_Pos) /*!< 0x00000008 */ +#define EXTI_IMR_MR3 EXTI_IMR_MR3_Msk /*!< Interrupt Mask on line 3 */ +#define EXTI_IMR_MR4_Pos (4U) +#define EXTI_IMR_MR4_Msk (0x1UL << EXTI_IMR_MR4_Pos) /*!< 0x00000010 */ +#define EXTI_IMR_MR4 EXTI_IMR_MR4_Msk /*!< Interrupt Mask on line 4 */ +#define EXTI_IMR_MR5_Pos (5U) +#define EXTI_IMR_MR5_Msk (0x1UL << EXTI_IMR_MR5_Pos) /*!< 0x00000020 */ +#define EXTI_IMR_MR5 EXTI_IMR_MR5_Msk /*!< Interrupt Mask on line 5 */ +#define EXTI_IMR_MR6_Pos (6U) +#define EXTI_IMR_MR6_Msk (0x1UL << EXTI_IMR_MR6_Pos) /*!< 0x00000040 */ +#define EXTI_IMR_MR6 EXTI_IMR_MR6_Msk /*!< Interrupt Mask on line 6 */ +#define EXTI_IMR_MR7_Pos (7U) +#define EXTI_IMR_MR7_Msk (0x1UL << EXTI_IMR_MR7_Pos) /*!< 0x00000080 */ +#define EXTI_IMR_MR7 EXTI_IMR_MR7_Msk /*!< Interrupt Mask on line 7 */ +#define EXTI_IMR_MR8_Pos (8U) +#define EXTI_IMR_MR8_Msk (0x1UL << EXTI_IMR_MR8_Pos) /*!< 0x00000100 */ +#define EXTI_IMR_MR8 EXTI_IMR_MR8_Msk /*!< Interrupt Mask on line 8 */ +#define EXTI_IMR_MR9_Pos (9U) +#define EXTI_IMR_MR9_Msk (0x1UL << EXTI_IMR_MR9_Pos) /*!< 0x00000200 */ +#define EXTI_IMR_MR9 EXTI_IMR_MR9_Msk /*!< Interrupt Mask on line 9 */ +#define EXTI_IMR_MR10_Pos (10U) +#define EXTI_IMR_MR10_Msk (0x1UL << EXTI_IMR_MR10_Pos) /*!< 0x00000400 */ +#define EXTI_IMR_MR10 EXTI_IMR_MR10_Msk /*!< Interrupt Mask on line 10 */ +#define EXTI_IMR_MR11_Pos (11U) +#define EXTI_IMR_MR11_Msk (0x1UL << EXTI_IMR_MR11_Pos) /*!< 0x00000800 */ +#define EXTI_IMR_MR11 EXTI_IMR_MR11_Msk /*!< Interrupt Mask on line 11 */ +#define EXTI_IMR_MR12_Pos (12U) +#define EXTI_IMR_MR12_Msk (0x1UL << EXTI_IMR_MR12_Pos) /*!< 0x00001000 */ +#define EXTI_IMR_MR12 EXTI_IMR_MR12_Msk /*!< Interrupt Mask on line 12 */ +#define EXTI_IMR_MR13_Pos (13U) +#define EXTI_IMR_MR13_Msk (0x1UL << EXTI_IMR_MR13_Pos) /*!< 0x00002000 */ +#define EXTI_IMR_MR13 EXTI_IMR_MR13_Msk /*!< Interrupt Mask on line 13 */ +#define EXTI_IMR_MR14_Pos (14U) +#define EXTI_IMR_MR14_Msk (0x1UL << EXTI_IMR_MR14_Pos) /*!< 0x00004000 */ +#define EXTI_IMR_MR14 EXTI_IMR_MR14_Msk /*!< Interrupt Mask on line 14 */ +#define EXTI_IMR_MR15_Pos (15U) +#define EXTI_IMR_MR15_Msk (0x1UL << EXTI_IMR_MR15_Pos) /*!< 0x00008000 */ +#define EXTI_IMR_MR15 EXTI_IMR_MR15_Msk /*!< Interrupt Mask on line 15 */ +#define EXTI_IMR_MR16_Pos (16U) +#define EXTI_IMR_MR16_Msk (0x1UL << EXTI_IMR_MR16_Pos) /*!< 0x00010000 */ +#define EXTI_IMR_MR16 EXTI_IMR_MR16_Msk /*!< Interrupt Mask on line 16 */ +#define EXTI_IMR_MR17_Pos (17U) +#define EXTI_IMR_MR17_Msk (0x1UL << EXTI_IMR_MR17_Pos) /*!< 0x00020000 */ +#define EXTI_IMR_MR17 EXTI_IMR_MR17_Msk /*!< Interrupt Mask on line 17 */ +#define EXTI_IMR_MR18_Pos (18U) +#define EXTI_IMR_MR18_Msk (0x1UL << EXTI_IMR_MR18_Pos) /*!< 0x00040000 */ +#define EXTI_IMR_MR18 EXTI_IMR_MR18_Msk /*!< Interrupt Mask on line 18 */ + +/* References Defines */ +#define EXTI_IMR_IM0 EXTI_IMR_MR0 +#define EXTI_IMR_IM1 EXTI_IMR_MR1 +#define EXTI_IMR_IM2 EXTI_IMR_MR2 +#define EXTI_IMR_IM3 EXTI_IMR_MR3 +#define EXTI_IMR_IM4 EXTI_IMR_MR4 +#define EXTI_IMR_IM5 EXTI_IMR_MR5 +#define EXTI_IMR_IM6 EXTI_IMR_MR6 +#define EXTI_IMR_IM7 EXTI_IMR_MR7 +#define EXTI_IMR_IM8 EXTI_IMR_MR8 +#define EXTI_IMR_IM9 EXTI_IMR_MR9 +#define EXTI_IMR_IM10 EXTI_IMR_MR10 +#define EXTI_IMR_IM11 EXTI_IMR_MR11 +#define EXTI_IMR_IM12 EXTI_IMR_MR12 +#define EXTI_IMR_IM13 EXTI_IMR_MR13 +#define EXTI_IMR_IM14 EXTI_IMR_MR14 +#define EXTI_IMR_IM15 EXTI_IMR_MR15 +#define EXTI_IMR_IM16 EXTI_IMR_MR16 +#define EXTI_IMR_IM17 EXTI_IMR_MR17 +#define EXTI_IMR_IM18 EXTI_IMR_MR18 +#define EXTI_IMR_IM 0x0007FFFFU /*!< Interrupt Mask All */ + +/******************* Bit definition for EXTI_EMR register *******************/ +#define EXTI_EMR_MR0_Pos (0U) +#define EXTI_EMR_MR0_Msk (0x1UL << EXTI_EMR_MR0_Pos) /*!< 0x00000001 */ +#define EXTI_EMR_MR0 EXTI_EMR_MR0_Msk /*!< Event Mask on line 0 */ +#define EXTI_EMR_MR1_Pos (1U) +#define EXTI_EMR_MR1_Msk (0x1UL << EXTI_EMR_MR1_Pos) /*!< 0x00000002 */ +#define EXTI_EMR_MR1 EXTI_EMR_MR1_Msk /*!< Event Mask on line 1 */ +#define EXTI_EMR_MR2_Pos (2U) +#define EXTI_EMR_MR2_Msk (0x1UL << EXTI_EMR_MR2_Pos) /*!< 0x00000004 */ +#define EXTI_EMR_MR2 EXTI_EMR_MR2_Msk /*!< Event Mask on line 2 */ +#define EXTI_EMR_MR3_Pos (3U) +#define EXTI_EMR_MR3_Msk (0x1UL << EXTI_EMR_MR3_Pos) /*!< 0x00000008 */ +#define EXTI_EMR_MR3 EXTI_EMR_MR3_Msk /*!< Event Mask on line 3 */ +#define EXTI_EMR_MR4_Pos (4U) +#define EXTI_EMR_MR4_Msk (0x1UL << EXTI_EMR_MR4_Pos) /*!< 0x00000010 */ +#define EXTI_EMR_MR4 EXTI_EMR_MR4_Msk /*!< Event Mask on line 4 */ +#define EXTI_EMR_MR5_Pos (5U) +#define EXTI_EMR_MR5_Msk (0x1UL << EXTI_EMR_MR5_Pos) /*!< 0x00000020 */ +#define EXTI_EMR_MR5 EXTI_EMR_MR5_Msk /*!< Event Mask on line 5 */ +#define EXTI_EMR_MR6_Pos (6U) +#define EXTI_EMR_MR6_Msk (0x1UL << EXTI_EMR_MR6_Pos) /*!< 0x00000040 */ +#define EXTI_EMR_MR6 EXTI_EMR_MR6_Msk /*!< Event Mask on line 6 */ +#define EXTI_EMR_MR7_Pos (7U) +#define EXTI_EMR_MR7_Msk (0x1UL << EXTI_EMR_MR7_Pos) /*!< 0x00000080 */ +#define EXTI_EMR_MR7 EXTI_EMR_MR7_Msk /*!< Event Mask on line 7 */ +#define EXTI_EMR_MR8_Pos (8U) +#define EXTI_EMR_MR8_Msk (0x1UL << EXTI_EMR_MR8_Pos) /*!< 0x00000100 */ +#define EXTI_EMR_MR8 EXTI_EMR_MR8_Msk /*!< Event Mask on line 8 */ +#define EXTI_EMR_MR9_Pos (9U) +#define EXTI_EMR_MR9_Msk (0x1UL << EXTI_EMR_MR9_Pos) /*!< 0x00000200 */ +#define EXTI_EMR_MR9 EXTI_EMR_MR9_Msk /*!< Event Mask on line 9 */ +#define EXTI_EMR_MR10_Pos (10U) +#define EXTI_EMR_MR10_Msk (0x1UL << EXTI_EMR_MR10_Pos) /*!< 0x00000400 */ +#define EXTI_EMR_MR10 EXTI_EMR_MR10_Msk /*!< Event Mask on line 10 */ +#define EXTI_EMR_MR11_Pos (11U) +#define EXTI_EMR_MR11_Msk (0x1UL << EXTI_EMR_MR11_Pos) /*!< 0x00000800 */ +#define EXTI_EMR_MR11 EXTI_EMR_MR11_Msk /*!< Event Mask on line 11 */ +#define EXTI_EMR_MR12_Pos (12U) +#define EXTI_EMR_MR12_Msk (0x1UL << EXTI_EMR_MR12_Pos) /*!< 0x00001000 */ +#define EXTI_EMR_MR12 EXTI_EMR_MR12_Msk /*!< Event Mask on line 12 */ +#define EXTI_EMR_MR13_Pos (13U) +#define EXTI_EMR_MR13_Msk (0x1UL << EXTI_EMR_MR13_Pos) /*!< 0x00002000 */ +#define EXTI_EMR_MR13 EXTI_EMR_MR13_Msk /*!< Event Mask on line 13 */ +#define EXTI_EMR_MR14_Pos (14U) +#define EXTI_EMR_MR14_Msk (0x1UL << EXTI_EMR_MR14_Pos) /*!< 0x00004000 */ +#define EXTI_EMR_MR14 EXTI_EMR_MR14_Msk /*!< Event Mask on line 14 */ +#define EXTI_EMR_MR15_Pos (15U) +#define EXTI_EMR_MR15_Msk (0x1UL << EXTI_EMR_MR15_Pos) /*!< 0x00008000 */ +#define EXTI_EMR_MR15 EXTI_EMR_MR15_Msk /*!< Event Mask on line 15 */ +#define EXTI_EMR_MR16_Pos (16U) +#define EXTI_EMR_MR16_Msk (0x1UL << EXTI_EMR_MR16_Pos) /*!< 0x00010000 */ +#define EXTI_EMR_MR16 EXTI_EMR_MR16_Msk /*!< Event Mask on line 16 */ +#define EXTI_EMR_MR17_Pos (17U) +#define EXTI_EMR_MR17_Msk (0x1UL << EXTI_EMR_MR17_Pos) /*!< 0x00020000 */ +#define EXTI_EMR_MR17 EXTI_EMR_MR17_Msk /*!< Event Mask on line 17 */ +#define EXTI_EMR_MR18_Pos (18U) +#define EXTI_EMR_MR18_Msk (0x1UL << EXTI_EMR_MR18_Pos) /*!< 0x00040000 */ +#define EXTI_EMR_MR18 EXTI_EMR_MR18_Msk /*!< Event Mask on line 18 */ + +/* References Defines */ +#define EXTI_EMR_EM0 EXTI_EMR_MR0 +#define EXTI_EMR_EM1 EXTI_EMR_MR1 +#define EXTI_EMR_EM2 EXTI_EMR_MR2 +#define EXTI_EMR_EM3 EXTI_EMR_MR3 +#define EXTI_EMR_EM4 EXTI_EMR_MR4 +#define EXTI_EMR_EM5 EXTI_EMR_MR5 +#define EXTI_EMR_EM6 EXTI_EMR_MR6 +#define EXTI_EMR_EM7 EXTI_EMR_MR7 +#define EXTI_EMR_EM8 EXTI_EMR_MR8 +#define EXTI_EMR_EM9 EXTI_EMR_MR9 +#define EXTI_EMR_EM10 EXTI_EMR_MR10 +#define EXTI_EMR_EM11 EXTI_EMR_MR11 +#define EXTI_EMR_EM12 EXTI_EMR_MR12 +#define EXTI_EMR_EM13 EXTI_EMR_MR13 +#define EXTI_EMR_EM14 EXTI_EMR_MR14 +#define EXTI_EMR_EM15 EXTI_EMR_MR15 +#define EXTI_EMR_EM16 EXTI_EMR_MR16 +#define EXTI_EMR_EM17 EXTI_EMR_MR17 +#define EXTI_EMR_EM18 EXTI_EMR_MR18 + +/****************** Bit definition for EXTI_RTSR register *******************/ +#define EXTI_RTSR_TR0_Pos (0U) +#define EXTI_RTSR_TR0_Msk (0x1UL << EXTI_RTSR_TR0_Pos) /*!< 0x00000001 */ +#define EXTI_RTSR_TR0 EXTI_RTSR_TR0_Msk /*!< Rising trigger event configuration bit of line 0 */ +#define EXTI_RTSR_TR1_Pos (1U) +#define EXTI_RTSR_TR1_Msk (0x1UL << EXTI_RTSR_TR1_Pos) /*!< 0x00000002 */ +#define EXTI_RTSR_TR1 EXTI_RTSR_TR1_Msk /*!< Rising trigger event configuration bit of line 1 */ +#define EXTI_RTSR_TR2_Pos (2U) +#define EXTI_RTSR_TR2_Msk (0x1UL << EXTI_RTSR_TR2_Pos) /*!< 0x00000004 */ +#define EXTI_RTSR_TR2 EXTI_RTSR_TR2_Msk /*!< Rising trigger event configuration bit of line 2 */ +#define EXTI_RTSR_TR3_Pos (3U) +#define EXTI_RTSR_TR3_Msk (0x1UL << EXTI_RTSR_TR3_Pos) /*!< 0x00000008 */ +#define EXTI_RTSR_TR3 EXTI_RTSR_TR3_Msk /*!< Rising trigger event configuration bit of line 3 */ +#define EXTI_RTSR_TR4_Pos (4U) +#define EXTI_RTSR_TR4_Msk (0x1UL << EXTI_RTSR_TR4_Pos) /*!< 0x00000010 */ +#define EXTI_RTSR_TR4 EXTI_RTSR_TR4_Msk /*!< Rising trigger event configuration bit of line 4 */ +#define EXTI_RTSR_TR5_Pos (5U) +#define EXTI_RTSR_TR5_Msk (0x1UL << EXTI_RTSR_TR5_Pos) /*!< 0x00000020 */ +#define EXTI_RTSR_TR5 EXTI_RTSR_TR5_Msk /*!< Rising trigger event configuration bit of line 5 */ +#define EXTI_RTSR_TR6_Pos (6U) +#define EXTI_RTSR_TR6_Msk (0x1UL << EXTI_RTSR_TR6_Pos) /*!< 0x00000040 */ +#define EXTI_RTSR_TR6 EXTI_RTSR_TR6_Msk /*!< Rising trigger event configuration bit of line 6 */ +#define EXTI_RTSR_TR7_Pos (7U) +#define EXTI_RTSR_TR7_Msk (0x1UL << EXTI_RTSR_TR7_Pos) /*!< 0x00000080 */ +#define EXTI_RTSR_TR7 EXTI_RTSR_TR7_Msk /*!< Rising trigger event configuration bit of line 7 */ +#define EXTI_RTSR_TR8_Pos (8U) +#define EXTI_RTSR_TR8_Msk (0x1UL << EXTI_RTSR_TR8_Pos) /*!< 0x00000100 */ +#define EXTI_RTSR_TR8 EXTI_RTSR_TR8_Msk /*!< Rising trigger event configuration bit of line 8 */ +#define EXTI_RTSR_TR9_Pos (9U) +#define EXTI_RTSR_TR9_Msk (0x1UL << EXTI_RTSR_TR9_Pos) /*!< 0x00000200 */ +#define EXTI_RTSR_TR9 EXTI_RTSR_TR9_Msk /*!< Rising trigger event configuration bit of line 9 */ +#define EXTI_RTSR_TR10_Pos (10U) +#define EXTI_RTSR_TR10_Msk (0x1UL << EXTI_RTSR_TR10_Pos) /*!< 0x00000400 */ +#define EXTI_RTSR_TR10 EXTI_RTSR_TR10_Msk /*!< Rising trigger event configuration bit of line 10 */ +#define EXTI_RTSR_TR11_Pos (11U) +#define EXTI_RTSR_TR11_Msk (0x1UL << EXTI_RTSR_TR11_Pos) /*!< 0x00000800 */ +#define EXTI_RTSR_TR11 EXTI_RTSR_TR11_Msk /*!< Rising trigger event configuration bit of line 11 */ +#define EXTI_RTSR_TR12_Pos (12U) +#define EXTI_RTSR_TR12_Msk (0x1UL << EXTI_RTSR_TR12_Pos) /*!< 0x00001000 */ +#define EXTI_RTSR_TR12 EXTI_RTSR_TR12_Msk /*!< Rising trigger event configuration bit of line 12 */ +#define EXTI_RTSR_TR13_Pos (13U) +#define EXTI_RTSR_TR13_Msk (0x1UL << EXTI_RTSR_TR13_Pos) /*!< 0x00002000 */ +#define EXTI_RTSR_TR13 EXTI_RTSR_TR13_Msk /*!< Rising trigger event configuration bit of line 13 */ +#define EXTI_RTSR_TR14_Pos (14U) +#define EXTI_RTSR_TR14_Msk (0x1UL << EXTI_RTSR_TR14_Pos) /*!< 0x00004000 */ +#define EXTI_RTSR_TR14 EXTI_RTSR_TR14_Msk /*!< Rising trigger event configuration bit of line 14 */ +#define EXTI_RTSR_TR15_Pos (15U) +#define EXTI_RTSR_TR15_Msk (0x1UL << EXTI_RTSR_TR15_Pos) /*!< 0x00008000 */ +#define EXTI_RTSR_TR15 EXTI_RTSR_TR15_Msk /*!< Rising trigger event configuration bit of line 15 */ +#define EXTI_RTSR_TR16_Pos (16U) +#define EXTI_RTSR_TR16_Msk (0x1UL << EXTI_RTSR_TR16_Pos) /*!< 0x00010000 */ +#define EXTI_RTSR_TR16 EXTI_RTSR_TR16_Msk /*!< Rising trigger event configuration bit of line 16 */ +#define EXTI_RTSR_TR17_Pos (17U) +#define EXTI_RTSR_TR17_Msk (0x1UL << EXTI_RTSR_TR17_Pos) /*!< 0x00020000 */ +#define EXTI_RTSR_TR17 EXTI_RTSR_TR17_Msk /*!< Rising trigger event configuration bit of line 17 */ +#define EXTI_RTSR_TR18_Pos (18U) +#define EXTI_RTSR_TR18_Msk (0x1UL << EXTI_RTSR_TR18_Pos) /*!< 0x00040000 */ +#define EXTI_RTSR_TR18 EXTI_RTSR_TR18_Msk /*!< Rising trigger event configuration bit of line 18 */ + +/* References Defines */ +#define EXTI_RTSR_RT0 EXTI_RTSR_TR0 +#define EXTI_RTSR_RT1 EXTI_RTSR_TR1 +#define EXTI_RTSR_RT2 EXTI_RTSR_TR2 +#define EXTI_RTSR_RT3 EXTI_RTSR_TR3 +#define EXTI_RTSR_RT4 EXTI_RTSR_TR4 +#define EXTI_RTSR_RT5 EXTI_RTSR_TR5 +#define EXTI_RTSR_RT6 EXTI_RTSR_TR6 +#define EXTI_RTSR_RT7 EXTI_RTSR_TR7 +#define EXTI_RTSR_RT8 EXTI_RTSR_TR8 +#define EXTI_RTSR_RT9 EXTI_RTSR_TR9 +#define EXTI_RTSR_RT10 EXTI_RTSR_TR10 +#define EXTI_RTSR_RT11 EXTI_RTSR_TR11 +#define EXTI_RTSR_RT12 EXTI_RTSR_TR12 +#define EXTI_RTSR_RT13 EXTI_RTSR_TR13 +#define EXTI_RTSR_RT14 EXTI_RTSR_TR14 +#define EXTI_RTSR_RT15 EXTI_RTSR_TR15 +#define EXTI_RTSR_RT16 EXTI_RTSR_TR16 +#define EXTI_RTSR_RT17 EXTI_RTSR_TR17 +#define EXTI_RTSR_RT18 EXTI_RTSR_TR18 + +/****************** Bit definition for EXTI_FTSR register *******************/ +#define EXTI_FTSR_TR0_Pos (0U) +#define EXTI_FTSR_TR0_Msk (0x1UL << EXTI_FTSR_TR0_Pos) /*!< 0x00000001 */ +#define EXTI_FTSR_TR0 EXTI_FTSR_TR0_Msk /*!< Falling trigger event configuration bit of line 0 */ +#define EXTI_FTSR_TR1_Pos (1U) +#define EXTI_FTSR_TR1_Msk (0x1UL << EXTI_FTSR_TR1_Pos) /*!< 0x00000002 */ +#define EXTI_FTSR_TR1 EXTI_FTSR_TR1_Msk /*!< Falling trigger event configuration bit of line 1 */ +#define EXTI_FTSR_TR2_Pos (2U) +#define EXTI_FTSR_TR2_Msk (0x1UL << EXTI_FTSR_TR2_Pos) /*!< 0x00000004 */ +#define EXTI_FTSR_TR2 EXTI_FTSR_TR2_Msk /*!< Falling trigger event configuration bit of line 2 */ +#define EXTI_FTSR_TR3_Pos (3U) +#define EXTI_FTSR_TR3_Msk (0x1UL << EXTI_FTSR_TR3_Pos) /*!< 0x00000008 */ +#define EXTI_FTSR_TR3 EXTI_FTSR_TR3_Msk /*!< Falling trigger event configuration bit of line 3 */ +#define EXTI_FTSR_TR4_Pos (4U) +#define EXTI_FTSR_TR4_Msk (0x1UL << EXTI_FTSR_TR4_Pos) /*!< 0x00000010 */ +#define EXTI_FTSR_TR4 EXTI_FTSR_TR4_Msk /*!< Falling trigger event configuration bit of line 4 */ +#define EXTI_FTSR_TR5_Pos (5U) +#define EXTI_FTSR_TR5_Msk (0x1UL << EXTI_FTSR_TR5_Pos) /*!< 0x00000020 */ +#define EXTI_FTSR_TR5 EXTI_FTSR_TR5_Msk /*!< Falling trigger event configuration bit of line 5 */ +#define EXTI_FTSR_TR6_Pos (6U) +#define EXTI_FTSR_TR6_Msk (0x1UL << EXTI_FTSR_TR6_Pos) /*!< 0x00000040 */ +#define EXTI_FTSR_TR6 EXTI_FTSR_TR6_Msk /*!< Falling trigger event configuration bit of line 6 */ +#define EXTI_FTSR_TR7_Pos (7U) +#define EXTI_FTSR_TR7_Msk (0x1UL << EXTI_FTSR_TR7_Pos) /*!< 0x00000080 */ +#define EXTI_FTSR_TR7 EXTI_FTSR_TR7_Msk /*!< Falling trigger event configuration bit of line 7 */ +#define EXTI_FTSR_TR8_Pos (8U) +#define EXTI_FTSR_TR8_Msk (0x1UL << EXTI_FTSR_TR8_Pos) /*!< 0x00000100 */ +#define EXTI_FTSR_TR8 EXTI_FTSR_TR8_Msk /*!< Falling trigger event configuration bit of line 8 */ +#define EXTI_FTSR_TR9_Pos (9U) +#define EXTI_FTSR_TR9_Msk (0x1UL << EXTI_FTSR_TR9_Pos) /*!< 0x00000200 */ +#define EXTI_FTSR_TR9 EXTI_FTSR_TR9_Msk /*!< Falling trigger event configuration bit of line 9 */ +#define EXTI_FTSR_TR10_Pos (10U) +#define EXTI_FTSR_TR10_Msk (0x1UL << EXTI_FTSR_TR10_Pos) /*!< 0x00000400 */ +#define EXTI_FTSR_TR10 EXTI_FTSR_TR10_Msk /*!< Falling trigger event configuration bit of line 10 */ +#define EXTI_FTSR_TR11_Pos (11U) +#define EXTI_FTSR_TR11_Msk (0x1UL << EXTI_FTSR_TR11_Pos) /*!< 0x00000800 */ +#define EXTI_FTSR_TR11 EXTI_FTSR_TR11_Msk /*!< Falling trigger event configuration bit of line 11 */ +#define EXTI_FTSR_TR12_Pos (12U) +#define EXTI_FTSR_TR12_Msk (0x1UL << EXTI_FTSR_TR12_Pos) /*!< 0x00001000 */ +#define EXTI_FTSR_TR12 EXTI_FTSR_TR12_Msk /*!< Falling trigger event configuration bit of line 12 */ +#define EXTI_FTSR_TR13_Pos (13U) +#define EXTI_FTSR_TR13_Msk (0x1UL << EXTI_FTSR_TR13_Pos) /*!< 0x00002000 */ +#define EXTI_FTSR_TR13 EXTI_FTSR_TR13_Msk /*!< Falling trigger event configuration bit of line 13 */ +#define EXTI_FTSR_TR14_Pos (14U) +#define EXTI_FTSR_TR14_Msk (0x1UL << EXTI_FTSR_TR14_Pos) /*!< 0x00004000 */ +#define EXTI_FTSR_TR14 EXTI_FTSR_TR14_Msk /*!< Falling trigger event configuration bit of line 14 */ +#define EXTI_FTSR_TR15_Pos (15U) +#define EXTI_FTSR_TR15_Msk (0x1UL << EXTI_FTSR_TR15_Pos) /*!< 0x00008000 */ +#define EXTI_FTSR_TR15 EXTI_FTSR_TR15_Msk /*!< Falling trigger event configuration bit of line 15 */ +#define EXTI_FTSR_TR16_Pos (16U) +#define EXTI_FTSR_TR16_Msk (0x1UL << EXTI_FTSR_TR16_Pos) /*!< 0x00010000 */ +#define EXTI_FTSR_TR16 EXTI_FTSR_TR16_Msk /*!< Falling trigger event configuration bit of line 16 */ +#define EXTI_FTSR_TR17_Pos (17U) +#define EXTI_FTSR_TR17_Msk (0x1UL << EXTI_FTSR_TR17_Pos) /*!< 0x00020000 */ +#define EXTI_FTSR_TR17 EXTI_FTSR_TR17_Msk /*!< Falling trigger event configuration bit of line 17 */ +#define EXTI_FTSR_TR18_Pos (18U) +#define EXTI_FTSR_TR18_Msk (0x1UL << EXTI_FTSR_TR18_Pos) /*!< 0x00040000 */ +#define EXTI_FTSR_TR18 EXTI_FTSR_TR18_Msk /*!< Falling trigger event configuration bit of line 18 */ + +/* References Defines */ +#define EXTI_FTSR_FT0 EXTI_FTSR_TR0 +#define EXTI_FTSR_FT1 EXTI_FTSR_TR1 +#define EXTI_FTSR_FT2 EXTI_FTSR_TR2 +#define EXTI_FTSR_FT3 EXTI_FTSR_TR3 +#define EXTI_FTSR_FT4 EXTI_FTSR_TR4 +#define EXTI_FTSR_FT5 EXTI_FTSR_TR5 +#define EXTI_FTSR_FT6 EXTI_FTSR_TR6 +#define EXTI_FTSR_FT7 EXTI_FTSR_TR7 +#define EXTI_FTSR_FT8 EXTI_FTSR_TR8 +#define EXTI_FTSR_FT9 EXTI_FTSR_TR9 +#define EXTI_FTSR_FT10 EXTI_FTSR_TR10 +#define EXTI_FTSR_FT11 EXTI_FTSR_TR11 +#define EXTI_FTSR_FT12 EXTI_FTSR_TR12 +#define EXTI_FTSR_FT13 EXTI_FTSR_TR13 +#define EXTI_FTSR_FT14 EXTI_FTSR_TR14 +#define EXTI_FTSR_FT15 EXTI_FTSR_TR15 +#define EXTI_FTSR_FT16 EXTI_FTSR_TR16 +#define EXTI_FTSR_FT17 EXTI_FTSR_TR17 +#define EXTI_FTSR_FT18 EXTI_FTSR_TR18 + +/****************** Bit definition for EXTI_SWIER register ******************/ +#define EXTI_SWIER_SWIER0_Pos (0U) +#define EXTI_SWIER_SWIER0_Msk (0x1UL << EXTI_SWIER_SWIER0_Pos) /*!< 0x00000001 */ +#define EXTI_SWIER_SWIER0 EXTI_SWIER_SWIER0_Msk /*!< Software Interrupt on line 0 */ +#define EXTI_SWIER_SWIER1_Pos (1U) +#define EXTI_SWIER_SWIER1_Msk (0x1UL << EXTI_SWIER_SWIER1_Pos) /*!< 0x00000002 */ +#define EXTI_SWIER_SWIER1 EXTI_SWIER_SWIER1_Msk /*!< Software Interrupt on line 1 */ +#define EXTI_SWIER_SWIER2_Pos (2U) +#define EXTI_SWIER_SWIER2_Msk (0x1UL << EXTI_SWIER_SWIER2_Pos) /*!< 0x00000004 */ +#define EXTI_SWIER_SWIER2 EXTI_SWIER_SWIER2_Msk /*!< Software Interrupt on line 2 */ +#define EXTI_SWIER_SWIER3_Pos (3U) +#define EXTI_SWIER_SWIER3_Msk (0x1UL << EXTI_SWIER_SWIER3_Pos) /*!< 0x00000008 */ +#define EXTI_SWIER_SWIER3 EXTI_SWIER_SWIER3_Msk /*!< Software Interrupt on line 3 */ +#define EXTI_SWIER_SWIER4_Pos (4U) +#define EXTI_SWIER_SWIER4_Msk (0x1UL << EXTI_SWIER_SWIER4_Pos) /*!< 0x00000010 */ +#define EXTI_SWIER_SWIER4 EXTI_SWIER_SWIER4_Msk /*!< Software Interrupt on line 4 */ +#define EXTI_SWIER_SWIER5_Pos (5U) +#define EXTI_SWIER_SWIER5_Msk (0x1UL << EXTI_SWIER_SWIER5_Pos) /*!< 0x00000020 */ +#define EXTI_SWIER_SWIER5 EXTI_SWIER_SWIER5_Msk /*!< Software Interrupt on line 5 */ +#define EXTI_SWIER_SWIER6_Pos (6U) +#define EXTI_SWIER_SWIER6_Msk (0x1UL << EXTI_SWIER_SWIER6_Pos) /*!< 0x00000040 */ +#define EXTI_SWIER_SWIER6 EXTI_SWIER_SWIER6_Msk /*!< Software Interrupt on line 6 */ +#define EXTI_SWIER_SWIER7_Pos (7U) +#define EXTI_SWIER_SWIER7_Msk (0x1UL << EXTI_SWIER_SWIER7_Pos) /*!< 0x00000080 */ +#define EXTI_SWIER_SWIER7 EXTI_SWIER_SWIER7_Msk /*!< Software Interrupt on line 7 */ +#define EXTI_SWIER_SWIER8_Pos (8U) +#define EXTI_SWIER_SWIER8_Msk (0x1UL << EXTI_SWIER_SWIER8_Pos) /*!< 0x00000100 */ +#define EXTI_SWIER_SWIER8 EXTI_SWIER_SWIER8_Msk /*!< Software Interrupt on line 8 */ +#define EXTI_SWIER_SWIER9_Pos (9U) +#define EXTI_SWIER_SWIER9_Msk (0x1UL << EXTI_SWIER_SWIER9_Pos) /*!< 0x00000200 */ +#define EXTI_SWIER_SWIER9 EXTI_SWIER_SWIER9_Msk /*!< Software Interrupt on line 9 */ +#define EXTI_SWIER_SWIER10_Pos (10U) +#define EXTI_SWIER_SWIER10_Msk (0x1UL << EXTI_SWIER_SWIER10_Pos) /*!< 0x00000400 */ +#define EXTI_SWIER_SWIER10 EXTI_SWIER_SWIER10_Msk /*!< Software Interrupt on line 10 */ +#define EXTI_SWIER_SWIER11_Pos (11U) +#define EXTI_SWIER_SWIER11_Msk (0x1UL << EXTI_SWIER_SWIER11_Pos) /*!< 0x00000800 */ +#define EXTI_SWIER_SWIER11 EXTI_SWIER_SWIER11_Msk /*!< Software Interrupt on line 11 */ +#define EXTI_SWIER_SWIER12_Pos (12U) +#define EXTI_SWIER_SWIER12_Msk (0x1UL << EXTI_SWIER_SWIER12_Pos) /*!< 0x00001000 */ +#define EXTI_SWIER_SWIER12 EXTI_SWIER_SWIER12_Msk /*!< Software Interrupt on line 12 */ +#define EXTI_SWIER_SWIER13_Pos (13U) +#define EXTI_SWIER_SWIER13_Msk (0x1UL << EXTI_SWIER_SWIER13_Pos) /*!< 0x00002000 */ +#define EXTI_SWIER_SWIER13 EXTI_SWIER_SWIER13_Msk /*!< Software Interrupt on line 13 */ +#define EXTI_SWIER_SWIER14_Pos (14U) +#define EXTI_SWIER_SWIER14_Msk (0x1UL << EXTI_SWIER_SWIER14_Pos) /*!< 0x00004000 */ +#define EXTI_SWIER_SWIER14 EXTI_SWIER_SWIER14_Msk /*!< Software Interrupt on line 14 */ +#define EXTI_SWIER_SWIER15_Pos (15U) +#define EXTI_SWIER_SWIER15_Msk (0x1UL << EXTI_SWIER_SWIER15_Pos) /*!< 0x00008000 */ +#define EXTI_SWIER_SWIER15 EXTI_SWIER_SWIER15_Msk /*!< Software Interrupt on line 15 */ +#define EXTI_SWIER_SWIER16_Pos (16U) +#define EXTI_SWIER_SWIER16_Msk (0x1UL << EXTI_SWIER_SWIER16_Pos) /*!< 0x00010000 */ +#define EXTI_SWIER_SWIER16 EXTI_SWIER_SWIER16_Msk /*!< Software Interrupt on line 16 */ +#define EXTI_SWIER_SWIER17_Pos (17U) +#define EXTI_SWIER_SWIER17_Msk (0x1UL << EXTI_SWIER_SWIER17_Pos) /*!< 0x00020000 */ +#define EXTI_SWIER_SWIER17 EXTI_SWIER_SWIER17_Msk /*!< Software Interrupt on line 17 */ +#define EXTI_SWIER_SWIER18_Pos (18U) +#define EXTI_SWIER_SWIER18_Msk (0x1UL << EXTI_SWIER_SWIER18_Pos) /*!< 0x00040000 */ +#define EXTI_SWIER_SWIER18 EXTI_SWIER_SWIER18_Msk /*!< Software Interrupt on line 18 */ + +/* References Defines */ +#define EXTI_SWIER_SWI0 EXTI_SWIER_SWIER0 +#define EXTI_SWIER_SWI1 EXTI_SWIER_SWIER1 +#define EXTI_SWIER_SWI2 EXTI_SWIER_SWIER2 +#define EXTI_SWIER_SWI3 EXTI_SWIER_SWIER3 +#define EXTI_SWIER_SWI4 EXTI_SWIER_SWIER4 +#define EXTI_SWIER_SWI5 EXTI_SWIER_SWIER5 +#define EXTI_SWIER_SWI6 EXTI_SWIER_SWIER6 +#define EXTI_SWIER_SWI7 EXTI_SWIER_SWIER7 +#define EXTI_SWIER_SWI8 EXTI_SWIER_SWIER8 +#define EXTI_SWIER_SWI9 EXTI_SWIER_SWIER9 +#define EXTI_SWIER_SWI10 EXTI_SWIER_SWIER10 +#define EXTI_SWIER_SWI11 EXTI_SWIER_SWIER11 +#define EXTI_SWIER_SWI12 EXTI_SWIER_SWIER12 +#define EXTI_SWIER_SWI13 EXTI_SWIER_SWIER13 +#define EXTI_SWIER_SWI14 EXTI_SWIER_SWIER14 +#define EXTI_SWIER_SWI15 EXTI_SWIER_SWIER15 +#define EXTI_SWIER_SWI16 EXTI_SWIER_SWIER16 +#define EXTI_SWIER_SWI17 EXTI_SWIER_SWIER17 +#define EXTI_SWIER_SWI18 EXTI_SWIER_SWIER18 + +/******************* Bit definition for EXTI_PR register ********************/ +#define EXTI_PR_PR0_Pos (0U) +#define EXTI_PR_PR0_Msk (0x1UL << EXTI_PR_PR0_Pos) /*!< 0x00000001 */ +#define EXTI_PR_PR0 EXTI_PR_PR0_Msk /*!< Pending bit for line 0 */ +#define EXTI_PR_PR1_Pos (1U) +#define EXTI_PR_PR1_Msk (0x1UL << EXTI_PR_PR1_Pos) /*!< 0x00000002 */ +#define EXTI_PR_PR1 EXTI_PR_PR1_Msk /*!< Pending bit for line 1 */ +#define EXTI_PR_PR2_Pos (2U) +#define EXTI_PR_PR2_Msk (0x1UL << EXTI_PR_PR2_Pos) /*!< 0x00000004 */ +#define EXTI_PR_PR2 EXTI_PR_PR2_Msk /*!< Pending bit for line 2 */ +#define EXTI_PR_PR3_Pos (3U) +#define EXTI_PR_PR3_Msk (0x1UL << EXTI_PR_PR3_Pos) /*!< 0x00000008 */ +#define EXTI_PR_PR3 EXTI_PR_PR3_Msk /*!< Pending bit for line 3 */ +#define EXTI_PR_PR4_Pos (4U) +#define EXTI_PR_PR4_Msk (0x1UL << EXTI_PR_PR4_Pos) /*!< 0x00000010 */ +#define EXTI_PR_PR4 EXTI_PR_PR4_Msk /*!< Pending bit for line 4 */ +#define EXTI_PR_PR5_Pos (5U) +#define EXTI_PR_PR5_Msk (0x1UL << EXTI_PR_PR5_Pos) /*!< 0x00000020 */ +#define EXTI_PR_PR5 EXTI_PR_PR5_Msk /*!< Pending bit for line 5 */ +#define EXTI_PR_PR6_Pos (6U) +#define EXTI_PR_PR6_Msk (0x1UL << EXTI_PR_PR6_Pos) /*!< 0x00000040 */ +#define EXTI_PR_PR6 EXTI_PR_PR6_Msk /*!< Pending bit for line 6 */ +#define EXTI_PR_PR7_Pos (7U) +#define EXTI_PR_PR7_Msk (0x1UL << EXTI_PR_PR7_Pos) /*!< 0x00000080 */ +#define EXTI_PR_PR7 EXTI_PR_PR7_Msk /*!< Pending bit for line 7 */ +#define EXTI_PR_PR8_Pos (8U) +#define EXTI_PR_PR8_Msk (0x1UL << EXTI_PR_PR8_Pos) /*!< 0x00000100 */ +#define EXTI_PR_PR8 EXTI_PR_PR8_Msk /*!< Pending bit for line 8 */ +#define EXTI_PR_PR9_Pos (9U) +#define EXTI_PR_PR9_Msk (0x1UL << EXTI_PR_PR9_Pos) /*!< 0x00000200 */ +#define EXTI_PR_PR9 EXTI_PR_PR9_Msk /*!< Pending bit for line 9 */ +#define EXTI_PR_PR10_Pos (10U) +#define EXTI_PR_PR10_Msk (0x1UL << EXTI_PR_PR10_Pos) /*!< 0x00000400 */ +#define EXTI_PR_PR10 EXTI_PR_PR10_Msk /*!< Pending bit for line 10 */ +#define EXTI_PR_PR11_Pos (11U) +#define EXTI_PR_PR11_Msk (0x1UL << EXTI_PR_PR11_Pos) /*!< 0x00000800 */ +#define EXTI_PR_PR11 EXTI_PR_PR11_Msk /*!< Pending bit for line 11 */ +#define EXTI_PR_PR12_Pos (12U) +#define EXTI_PR_PR12_Msk (0x1UL << EXTI_PR_PR12_Pos) /*!< 0x00001000 */ +#define EXTI_PR_PR12 EXTI_PR_PR12_Msk /*!< Pending bit for line 12 */ +#define EXTI_PR_PR13_Pos (13U) +#define EXTI_PR_PR13_Msk (0x1UL << EXTI_PR_PR13_Pos) /*!< 0x00002000 */ +#define EXTI_PR_PR13 EXTI_PR_PR13_Msk /*!< Pending bit for line 13 */ +#define EXTI_PR_PR14_Pos (14U) +#define EXTI_PR_PR14_Msk (0x1UL << EXTI_PR_PR14_Pos) /*!< 0x00004000 */ +#define EXTI_PR_PR14 EXTI_PR_PR14_Msk /*!< Pending bit for line 14 */ +#define EXTI_PR_PR15_Pos (15U) +#define EXTI_PR_PR15_Msk (0x1UL << EXTI_PR_PR15_Pos) /*!< 0x00008000 */ +#define EXTI_PR_PR15 EXTI_PR_PR15_Msk /*!< Pending bit for line 15 */ +#define EXTI_PR_PR16_Pos (16U) +#define EXTI_PR_PR16_Msk (0x1UL << EXTI_PR_PR16_Pos) /*!< 0x00010000 */ +#define EXTI_PR_PR16 EXTI_PR_PR16_Msk /*!< Pending bit for line 16 */ +#define EXTI_PR_PR17_Pos (17U) +#define EXTI_PR_PR17_Msk (0x1UL << EXTI_PR_PR17_Pos) /*!< 0x00020000 */ +#define EXTI_PR_PR17 EXTI_PR_PR17_Msk /*!< Pending bit for line 17 */ +#define EXTI_PR_PR18_Pos (18U) +#define EXTI_PR_PR18_Msk (0x1UL << EXTI_PR_PR18_Pos) /*!< 0x00040000 */ +#define EXTI_PR_PR18 EXTI_PR_PR18_Msk /*!< Pending bit for line 18 */ + +/* References Defines */ +#define EXTI_PR_PIF0 EXTI_PR_PR0 +#define EXTI_PR_PIF1 EXTI_PR_PR1 +#define EXTI_PR_PIF2 EXTI_PR_PR2 +#define EXTI_PR_PIF3 EXTI_PR_PR3 +#define EXTI_PR_PIF4 EXTI_PR_PR4 +#define EXTI_PR_PIF5 EXTI_PR_PR5 +#define EXTI_PR_PIF6 EXTI_PR_PR6 +#define EXTI_PR_PIF7 EXTI_PR_PR7 +#define EXTI_PR_PIF8 EXTI_PR_PR8 +#define EXTI_PR_PIF9 EXTI_PR_PR9 +#define EXTI_PR_PIF10 EXTI_PR_PR10 +#define EXTI_PR_PIF11 EXTI_PR_PR11 +#define EXTI_PR_PIF12 EXTI_PR_PR12 +#define EXTI_PR_PIF13 EXTI_PR_PR13 +#define EXTI_PR_PIF14 EXTI_PR_PR14 +#define EXTI_PR_PIF15 EXTI_PR_PR15 +#define EXTI_PR_PIF16 EXTI_PR_PR16 +#define EXTI_PR_PIF17 EXTI_PR_PR17 +#define EXTI_PR_PIF18 EXTI_PR_PR18 + +/******************************************************************************/ +/* */ +/* DMA Controller */ +/* */ +/******************************************************************************/ + +/******************* Bit definition for DMA_ISR register ********************/ +#define DMA_ISR_GIF1_Pos (0U) +#define DMA_ISR_GIF1_Msk (0x1UL << DMA_ISR_GIF1_Pos) /*!< 0x00000001 */ +#define DMA_ISR_GIF1 DMA_ISR_GIF1_Msk /*!< Channel 1 Global interrupt flag */ +#define DMA_ISR_TCIF1_Pos (1U) +#define DMA_ISR_TCIF1_Msk (0x1UL << DMA_ISR_TCIF1_Pos) /*!< 0x00000002 */ +#define DMA_ISR_TCIF1 DMA_ISR_TCIF1_Msk /*!< Channel 1 Transfer Complete flag */ +#define DMA_ISR_HTIF1_Pos (2U) +#define DMA_ISR_HTIF1_Msk (0x1UL << DMA_ISR_HTIF1_Pos) /*!< 0x00000004 */ +#define DMA_ISR_HTIF1 DMA_ISR_HTIF1_Msk /*!< Channel 1 Half Transfer flag */ +#define DMA_ISR_TEIF1_Pos (3U) +#define DMA_ISR_TEIF1_Msk (0x1UL << DMA_ISR_TEIF1_Pos) /*!< 0x00000008 */ +#define DMA_ISR_TEIF1 DMA_ISR_TEIF1_Msk /*!< Channel 1 Transfer Error flag */ +#define DMA_ISR_GIF2_Pos (4U) +#define DMA_ISR_GIF2_Msk (0x1UL << DMA_ISR_GIF2_Pos) /*!< 0x00000010 */ +#define DMA_ISR_GIF2 DMA_ISR_GIF2_Msk /*!< Channel 2 Global interrupt flag */ +#define DMA_ISR_TCIF2_Pos (5U) +#define DMA_ISR_TCIF2_Msk (0x1UL << DMA_ISR_TCIF2_Pos) /*!< 0x00000020 */ +#define DMA_ISR_TCIF2 DMA_ISR_TCIF2_Msk /*!< Channel 2 Transfer Complete flag */ +#define DMA_ISR_HTIF2_Pos (6U) +#define DMA_ISR_HTIF2_Msk (0x1UL << DMA_ISR_HTIF2_Pos) /*!< 0x00000040 */ +#define DMA_ISR_HTIF2 DMA_ISR_HTIF2_Msk /*!< Channel 2 Half Transfer flag */ +#define DMA_ISR_TEIF2_Pos (7U) +#define DMA_ISR_TEIF2_Msk (0x1UL << DMA_ISR_TEIF2_Pos) /*!< 0x00000080 */ +#define DMA_ISR_TEIF2 DMA_ISR_TEIF2_Msk /*!< Channel 2 Transfer Error flag */ +#define DMA_ISR_GIF3_Pos (8U) +#define DMA_ISR_GIF3_Msk (0x1UL << DMA_ISR_GIF3_Pos) /*!< 0x00000100 */ +#define DMA_ISR_GIF3 DMA_ISR_GIF3_Msk /*!< Channel 3 Global interrupt flag */ +#define DMA_ISR_TCIF3_Pos (9U) +#define DMA_ISR_TCIF3_Msk (0x1UL << DMA_ISR_TCIF3_Pos) /*!< 0x00000200 */ +#define DMA_ISR_TCIF3 DMA_ISR_TCIF3_Msk /*!< Channel 3 Transfer Complete flag */ +#define DMA_ISR_HTIF3_Pos (10U) +#define DMA_ISR_HTIF3_Msk (0x1UL << DMA_ISR_HTIF3_Pos) /*!< 0x00000400 */ +#define DMA_ISR_HTIF3 DMA_ISR_HTIF3_Msk /*!< Channel 3 Half Transfer flag */ +#define DMA_ISR_TEIF3_Pos (11U) +#define DMA_ISR_TEIF3_Msk (0x1UL << DMA_ISR_TEIF3_Pos) /*!< 0x00000800 */ +#define DMA_ISR_TEIF3 DMA_ISR_TEIF3_Msk /*!< Channel 3 Transfer Error flag */ +#define DMA_ISR_GIF4_Pos (12U) +#define DMA_ISR_GIF4_Msk (0x1UL << DMA_ISR_GIF4_Pos) /*!< 0x00001000 */ +#define DMA_ISR_GIF4 DMA_ISR_GIF4_Msk /*!< Channel 4 Global interrupt flag */ +#define DMA_ISR_TCIF4_Pos (13U) +#define DMA_ISR_TCIF4_Msk (0x1UL << DMA_ISR_TCIF4_Pos) /*!< 0x00002000 */ +#define DMA_ISR_TCIF4 DMA_ISR_TCIF4_Msk /*!< Channel 4 Transfer Complete flag */ +#define DMA_ISR_HTIF4_Pos (14U) +#define DMA_ISR_HTIF4_Msk (0x1UL << DMA_ISR_HTIF4_Pos) /*!< 0x00004000 */ +#define DMA_ISR_HTIF4 DMA_ISR_HTIF4_Msk /*!< Channel 4 Half Transfer flag */ +#define DMA_ISR_TEIF4_Pos (15U) +#define DMA_ISR_TEIF4_Msk (0x1UL << DMA_ISR_TEIF4_Pos) /*!< 0x00008000 */ +#define DMA_ISR_TEIF4 DMA_ISR_TEIF4_Msk /*!< Channel 4 Transfer Error flag */ +#define DMA_ISR_GIF5_Pos (16U) +#define DMA_ISR_GIF5_Msk (0x1UL << DMA_ISR_GIF5_Pos) /*!< 0x00010000 */ +#define DMA_ISR_GIF5 DMA_ISR_GIF5_Msk /*!< Channel 5 Global interrupt flag */ +#define DMA_ISR_TCIF5_Pos (17U) +#define DMA_ISR_TCIF5_Msk (0x1UL << DMA_ISR_TCIF5_Pos) /*!< 0x00020000 */ +#define DMA_ISR_TCIF5 DMA_ISR_TCIF5_Msk /*!< Channel 5 Transfer Complete flag */ +#define DMA_ISR_HTIF5_Pos (18U) +#define DMA_ISR_HTIF5_Msk (0x1UL << DMA_ISR_HTIF5_Pos) /*!< 0x00040000 */ +#define DMA_ISR_HTIF5 DMA_ISR_HTIF5_Msk /*!< Channel 5 Half Transfer flag */ +#define DMA_ISR_TEIF5_Pos (19U) +#define DMA_ISR_TEIF5_Msk (0x1UL << DMA_ISR_TEIF5_Pos) /*!< 0x00080000 */ +#define DMA_ISR_TEIF5 DMA_ISR_TEIF5_Msk /*!< Channel 5 Transfer Error flag */ +#define DMA_ISR_GIF6_Pos (20U) +#define DMA_ISR_GIF6_Msk (0x1UL << DMA_ISR_GIF6_Pos) /*!< 0x00100000 */ +#define DMA_ISR_GIF6 DMA_ISR_GIF6_Msk /*!< Channel 6 Global interrupt flag */ +#define DMA_ISR_TCIF6_Pos (21U) +#define DMA_ISR_TCIF6_Msk (0x1UL << DMA_ISR_TCIF6_Pos) /*!< 0x00200000 */ +#define DMA_ISR_TCIF6 DMA_ISR_TCIF6_Msk /*!< Channel 6 Transfer Complete flag */ +#define DMA_ISR_HTIF6_Pos (22U) +#define DMA_ISR_HTIF6_Msk (0x1UL << DMA_ISR_HTIF6_Pos) /*!< 0x00400000 */ +#define DMA_ISR_HTIF6 DMA_ISR_HTIF6_Msk /*!< Channel 6 Half Transfer flag */ +#define DMA_ISR_TEIF6_Pos (23U) +#define DMA_ISR_TEIF6_Msk (0x1UL << DMA_ISR_TEIF6_Pos) /*!< 0x00800000 */ +#define DMA_ISR_TEIF6 DMA_ISR_TEIF6_Msk /*!< Channel 6 Transfer Error flag */ +#define DMA_ISR_GIF7_Pos (24U) +#define DMA_ISR_GIF7_Msk (0x1UL << DMA_ISR_GIF7_Pos) /*!< 0x01000000 */ +#define DMA_ISR_GIF7 DMA_ISR_GIF7_Msk /*!< Channel 7 Global interrupt flag */ +#define DMA_ISR_TCIF7_Pos (25U) +#define DMA_ISR_TCIF7_Msk (0x1UL << DMA_ISR_TCIF7_Pos) /*!< 0x02000000 */ +#define DMA_ISR_TCIF7 DMA_ISR_TCIF7_Msk /*!< Channel 7 Transfer Complete flag */ +#define DMA_ISR_HTIF7_Pos (26U) +#define DMA_ISR_HTIF7_Msk (0x1UL << DMA_ISR_HTIF7_Pos) /*!< 0x04000000 */ +#define DMA_ISR_HTIF7 DMA_ISR_HTIF7_Msk /*!< Channel 7 Half Transfer flag */ +#define DMA_ISR_TEIF7_Pos (27U) +#define DMA_ISR_TEIF7_Msk (0x1UL << DMA_ISR_TEIF7_Pos) /*!< 0x08000000 */ +#define DMA_ISR_TEIF7 DMA_ISR_TEIF7_Msk /*!< Channel 7 Transfer Error flag */ + +/******************* Bit definition for DMA_IFCR register *******************/ +#define DMA_IFCR_CGIF1_Pos (0U) +#define DMA_IFCR_CGIF1_Msk (0x1UL << DMA_IFCR_CGIF1_Pos) /*!< 0x00000001 */ +#define DMA_IFCR_CGIF1 DMA_IFCR_CGIF1_Msk /*!< Channel 1 Global interrupt clear */ +#define DMA_IFCR_CTCIF1_Pos (1U) +#define DMA_IFCR_CTCIF1_Msk (0x1UL << DMA_IFCR_CTCIF1_Pos) /*!< 0x00000002 */ +#define DMA_IFCR_CTCIF1 DMA_IFCR_CTCIF1_Msk /*!< Channel 1 Transfer Complete clear */ +#define DMA_IFCR_CHTIF1_Pos (2U) +#define DMA_IFCR_CHTIF1_Msk (0x1UL << DMA_IFCR_CHTIF1_Pos) /*!< 0x00000004 */ +#define DMA_IFCR_CHTIF1 DMA_IFCR_CHTIF1_Msk /*!< Channel 1 Half Transfer clear */ +#define DMA_IFCR_CTEIF1_Pos (3U) +#define DMA_IFCR_CTEIF1_Msk (0x1UL << DMA_IFCR_CTEIF1_Pos) /*!< 0x00000008 */ +#define DMA_IFCR_CTEIF1 DMA_IFCR_CTEIF1_Msk /*!< Channel 1 Transfer Error clear */ +#define DMA_IFCR_CGIF2_Pos (4U) +#define DMA_IFCR_CGIF2_Msk (0x1UL << DMA_IFCR_CGIF2_Pos) /*!< 0x00000010 */ +#define DMA_IFCR_CGIF2 DMA_IFCR_CGIF2_Msk /*!< Channel 2 Global interrupt clear */ +#define DMA_IFCR_CTCIF2_Pos (5U) +#define DMA_IFCR_CTCIF2_Msk (0x1UL << DMA_IFCR_CTCIF2_Pos) /*!< 0x00000020 */ +#define DMA_IFCR_CTCIF2 DMA_IFCR_CTCIF2_Msk /*!< Channel 2 Transfer Complete clear */ +#define DMA_IFCR_CHTIF2_Pos (6U) +#define DMA_IFCR_CHTIF2_Msk (0x1UL << DMA_IFCR_CHTIF2_Pos) /*!< 0x00000040 */ +#define DMA_IFCR_CHTIF2 DMA_IFCR_CHTIF2_Msk /*!< Channel 2 Half Transfer clear */ +#define DMA_IFCR_CTEIF2_Pos (7U) +#define DMA_IFCR_CTEIF2_Msk (0x1UL << DMA_IFCR_CTEIF2_Pos) /*!< 0x00000080 */ +#define DMA_IFCR_CTEIF2 DMA_IFCR_CTEIF2_Msk /*!< Channel 2 Transfer Error clear */ +#define DMA_IFCR_CGIF3_Pos (8U) +#define DMA_IFCR_CGIF3_Msk (0x1UL << DMA_IFCR_CGIF3_Pos) /*!< 0x00000100 */ +#define DMA_IFCR_CGIF3 DMA_IFCR_CGIF3_Msk /*!< Channel 3 Global interrupt clear */ +#define DMA_IFCR_CTCIF3_Pos (9U) +#define DMA_IFCR_CTCIF3_Msk (0x1UL << DMA_IFCR_CTCIF3_Pos) /*!< 0x00000200 */ +#define DMA_IFCR_CTCIF3 DMA_IFCR_CTCIF3_Msk /*!< Channel 3 Transfer Complete clear */ +#define DMA_IFCR_CHTIF3_Pos (10U) +#define DMA_IFCR_CHTIF3_Msk (0x1UL << DMA_IFCR_CHTIF3_Pos) /*!< 0x00000400 */ +#define DMA_IFCR_CHTIF3 DMA_IFCR_CHTIF3_Msk /*!< Channel 3 Half Transfer clear */ +#define DMA_IFCR_CTEIF3_Pos (11U) +#define DMA_IFCR_CTEIF3_Msk (0x1UL << DMA_IFCR_CTEIF3_Pos) /*!< 0x00000800 */ +#define DMA_IFCR_CTEIF3 DMA_IFCR_CTEIF3_Msk /*!< Channel 3 Transfer Error clear */ +#define DMA_IFCR_CGIF4_Pos (12U) +#define DMA_IFCR_CGIF4_Msk (0x1UL << DMA_IFCR_CGIF4_Pos) /*!< 0x00001000 */ +#define DMA_IFCR_CGIF4 DMA_IFCR_CGIF4_Msk /*!< Channel 4 Global interrupt clear */ +#define DMA_IFCR_CTCIF4_Pos (13U) +#define DMA_IFCR_CTCIF4_Msk (0x1UL << DMA_IFCR_CTCIF4_Pos) /*!< 0x00002000 */ +#define DMA_IFCR_CTCIF4 DMA_IFCR_CTCIF4_Msk /*!< Channel 4 Transfer Complete clear */ +#define DMA_IFCR_CHTIF4_Pos (14U) +#define DMA_IFCR_CHTIF4_Msk (0x1UL << DMA_IFCR_CHTIF4_Pos) /*!< 0x00004000 */ +#define DMA_IFCR_CHTIF4 DMA_IFCR_CHTIF4_Msk /*!< Channel 4 Half Transfer clear */ +#define DMA_IFCR_CTEIF4_Pos (15U) +#define DMA_IFCR_CTEIF4_Msk (0x1UL << DMA_IFCR_CTEIF4_Pos) /*!< 0x00008000 */ +#define DMA_IFCR_CTEIF4 DMA_IFCR_CTEIF4_Msk /*!< Channel 4 Transfer Error clear */ +#define DMA_IFCR_CGIF5_Pos (16U) +#define DMA_IFCR_CGIF5_Msk (0x1UL << DMA_IFCR_CGIF5_Pos) /*!< 0x00010000 */ +#define DMA_IFCR_CGIF5 DMA_IFCR_CGIF5_Msk /*!< Channel 5 Global interrupt clear */ +#define DMA_IFCR_CTCIF5_Pos (17U) +#define DMA_IFCR_CTCIF5_Msk (0x1UL << DMA_IFCR_CTCIF5_Pos) /*!< 0x00020000 */ +#define DMA_IFCR_CTCIF5 DMA_IFCR_CTCIF5_Msk /*!< Channel 5 Transfer Complete clear */ +#define DMA_IFCR_CHTIF5_Pos (18U) +#define DMA_IFCR_CHTIF5_Msk (0x1UL << DMA_IFCR_CHTIF5_Pos) /*!< 0x00040000 */ +#define DMA_IFCR_CHTIF5 DMA_IFCR_CHTIF5_Msk /*!< Channel 5 Half Transfer clear */ +#define DMA_IFCR_CTEIF5_Pos (19U) +#define DMA_IFCR_CTEIF5_Msk (0x1UL << DMA_IFCR_CTEIF5_Pos) /*!< 0x00080000 */ +#define DMA_IFCR_CTEIF5 DMA_IFCR_CTEIF5_Msk /*!< Channel 5 Transfer Error clear */ +#define DMA_IFCR_CGIF6_Pos (20U) +#define DMA_IFCR_CGIF6_Msk (0x1UL << DMA_IFCR_CGIF6_Pos) /*!< 0x00100000 */ +#define DMA_IFCR_CGIF6 DMA_IFCR_CGIF6_Msk /*!< Channel 6 Global interrupt clear */ +#define DMA_IFCR_CTCIF6_Pos (21U) +#define DMA_IFCR_CTCIF6_Msk (0x1UL << DMA_IFCR_CTCIF6_Pos) /*!< 0x00200000 */ +#define DMA_IFCR_CTCIF6 DMA_IFCR_CTCIF6_Msk /*!< Channel 6 Transfer Complete clear */ +#define DMA_IFCR_CHTIF6_Pos (22U) +#define DMA_IFCR_CHTIF6_Msk (0x1UL << DMA_IFCR_CHTIF6_Pos) /*!< 0x00400000 */ +#define DMA_IFCR_CHTIF6 DMA_IFCR_CHTIF6_Msk /*!< Channel 6 Half Transfer clear */ +#define DMA_IFCR_CTEIF6_Pos (23U) +#define DMA_IFCR_CTEIF6_Msk (0x1UL << DMA_IFCR_CTEIF6_Pos) /*!< 0x00800000 */ +#define DMA_IFCR_CTEIF6 DMA_IFCR_CTEIF6_Msk /*!< Channel 6 Transfer Error clear */ +#define DMA_IFCR_CGIF7_Pos (24U) +#define DMA_IFCR_CGIF7_Msk (0x1UL << DMA_IFCR_CGIF7_Pos) /*!< 0x01000000 */ +#define DMA_IFCR_CGIF7 DMA_IFCR_CGIF7_Msk /*!< Channel 7 Global interrupt clear */ +#define DMA_IFCR_CTCIF7_Pos (25U) +#define DMA_IFCR_CTCIF7_Msk (0x1UL << DMA_IFCR_CTCIF7_Pos) /*!< 0x02000000 */ +#define DMA_IFCR_CTCIF7 DMA_IFCR_CTCIF7_Msk /*!< Channel 7 Transfer Complete clear */ +#define DMA_IFCR_CHTIF7_Pos (26U) +#define DMA_IFCR_CHTIF7_Msk (0x1UL << DMA_IFCR_CHTIF7_Pos) /*!< 0x04000000 */ +#define DMA_IFCR_CHTIF7 DMA_IFCR_CHTIF7_Msk /*!< Channel 7 Half Transfer clear */ +#define DMA_IFCR_CTEIF7_Pos (27U) +#define DMA_IFCR_CTEIF7_Msk (0x1UL << DMA_IFCR_CTEIF7_Pos) /*!< 0x08000000 */ +#define DMA_IFCR_CTEIF7 DMA_IFCR_CTEIF7_Msk /*!< Channel 7 Transfer Error clear */ + +/******************* Bit definition for DMA_CCR register *******************/ +#define DMA_CCR_EN_Pos (0U) +#define DMA_CCR_EN_Msk (0x1UL << DMA_CCR_EN_Pos) /*!< 0x00000001 */ +#define DMA_CCR_EN DMA_CCR_EN_Msk /*!< Channel enable */ +#define DMA_CCR_TCIE_Pos (1U) +#define DMA_CCR_TCIE_Msk (0x1UL << DMA_CCR_TCIE_Pos) /*!< 0x00000002 */ +#define DMA_CCR_TCIE DMA_CCR_TCIE_Msk /*!< Transfer complete interrupt enable */ +#define DMA_CCR_HTIE_Pos (2U) +#define DMA_CCR_HTIE_Msk (0x1UL << DMA_CCR_HTIE_Pos) /*!< 0x00000004 */ +#define DMA_CCR_HTIE DMA_CCR_HTIE_Msk /*!< Half Transfer interrupt enable */ +#define DMA_CCR_TEIE_Pos (3U) +#define DMA_CCR_TEIE_Msk (0x1UL << DMA_CCR_TEIE_Pos) /*!< 0x00000008 */ +#define DMA_CCR_TEIE DMA_CCR_TEIE_Msk /*!< Transfer error interrupt enable */ +#define DMA_CCR_DIR_Pos (4U) +#define DMA_CCR_DIR_Msk (0x1UL << DMA_CCR_DIR_Pos) /*!< 0x00000010 */ +#define DMA_CCR_DIR DMA_CCR_DIR_Msk /*!< Data transfer direction */ +#define DMA_CCR_CIRC_Pos (5U) +#define DMA_CCR_CIRC_Msk (0x1UL << DMA_CCR_CIRC_Pos) /*!< 0x00000020 */ +#define DMA_CCR_CIRC DMA_CCR_CIRC_Msk /*!< Circular mode */ +#define DMA_CCR_PINC_Pos (6U) +#define DMA_CCR_PINC_Msk (0x1UL << DMA_CCR_PINC_Pos) /*!< 0x00000040 */ +#define DMA_CCR_PINC DMA_CCR_PINC_Msk /*!< Peripheral increment mode */ +#define DMA_CCR_MINC_Pos (7U) +#define DMA_CCR_MINC_Msk (0x1UL << DMA_CCR_MINC_Pos) /*!< 0x00000080 */ +#define DMA_CCR_MINC DMA_CCR_MINC_Msk /*!< Memory increment mode */ + +#define DMA_CCR_PSIZE_Pos (8U) +#define DMA_CCR_PSIZE_Msk (0x3UL << DMA_CCR_PSIZE_Pos) /*!< 0x00000300 */ +#define DMA_CCR_PSIZE DMA_CCR_PSIZE_Msk /*!< PSIZE[1:0] bits (Peripheral size) */ +#define DMA_CCR_PSIZE_0 (0x1UL << DMA_CCR_PSIZE_Pos) /*!< 0x00000100 */ +#define DMA_CCR_PSIZE_1 (0x2UL << DMA_CCR_PSIZE_Pos) /*!< 0x00000200 */ + +#define DMA_CCR_MSIZE_Pos (10U) +#define DMA_CCR_MSIZE_Msk (0x3UL << DMA_CCR_MSIZE_Pos) /*!< 0x00000C00 */ +#define DMA_CCR_MSIZE DMA_CCR_MSIZE_Msk /*!< MSIZE[1:0] bits (Memory size) */ +#define DMA_CCR_MSIZE_0 (0x1UL << DMA_CCR_MSIZE_Pos) /*!< 0x00000400 */ +#define DMA_CCR_MSIZE_1 (0x2UL << DMA_CCR_MSIZE_Pos) /*!< 0x00000800 */ + +#define DMA_CCR_PL_Pos (12U) +#define DMA_CCR_PL_Msk (0x3UL << DMA_CCR_PL_Pos) /*!< 0x00003000 */ +#define DMA_CCR_PL DMA_CCR_PL_Msk /*!< PL[1:0] bits(Channel Priority level) */ +#define DMA_CCR_PL_0 (0x1UL << DMA_CCR_PL_Pos) /*!< 0x00001000 */ +#define DMA_CCR_PL_1 (0x2UL << DMA_CCR_PL_Pos) /*!< 0x00002000 */ + +#define DMA_CCR_MEM2MEM_Pos (14U) +#define DMA_CCR_MEM2MEM_Msk (0x1UL << DMA_CCR_MEM2MEM_Pos) /*!< 0x00004000 */ +#define DMA_CCR_MEM2MEM DMA_CCR_MEM2MEM_Msk /*!< Memory to memory mode */ + +/****************** Bit definition for DMA_CNDTR register ******************/ +#define DMA_CNDTR_NDT_Pos (0U) +#define DMA_CNDTR_NDT_Msk (0xFFFFUL << DMA_CNDTR_NDT_Pos) /*!< 0x0000FFFF */ +#define DMA_CNDTR_NDT DMA_CNDTR_NDT_Msk /*!< Number of data to Transfer */ + +/****************** Bit definition for DMA_CPAR register *******************/ +#define DMA_CPAR_PA_Pos (0U) +#define DMA_CPAR_PA_Msk (0xFFFFFFFFUL << DMA_CPAR_PA_Pos) /*!< 0xFFFFFFFF */ +#define DMA_CPAR_PA DMA_CPAR_PA_Msk /*!< Peripheral Address */ + +/****************** Bit definition for DMA_CMAR register *******************/ +#define DMA_CMAR_MA_Pos (0U) +#define DMA_CMAR_MA_Msk (0xFFFFFFFFUL << DMA_CMAR_MA_Pos) /*!< 0xFFFFFFFF */ +#define DMA_CMAR_MA DMA_CMAR_MA_Msk /*!< Memory Address */ + +/******************************************************************************/ +/* */ +/* Analog to Digital Converter (ADC) */ +/* */ +/******************************************************************************/ + +/* + * @brief Specific device feature definitions (not present on all devices in the STM32F1 family) + */ +#define ADC_MULTIMODE_SUPPORT /*!< ADC feature available only on specific devices: multimode available on devices with several ADC instances */ + +/******************** Bit definition for ADC_SR register ********************/ +#define ADC_SR_AWD_Pos (0U) +#define ADC_SR_AWD_Msk (0x1UL << ADC_SR_AWD_Pos) /*!< 0x00000001 */ +#define ADC_SR_AWD ADC_SR_AWD_Msk /*!< ADC analog watchdog 1 flag */ +#define ADC_SR_EOS_Pos (1U) +#define ADC_SR_EOS_Msk (0x1UL << ADC_SR_EOS_Pos) /*!< 0x00000002 */ +#define ADC_SR_EOS ADC_SR_EOS_Msk /*!< ADC group regular end of sequence conversions flag */ +#define ADC_SR_JEOS_Pos (2U) +#define ADC_SR_JEOS_Msk (0x1UL << ADC_SR_JEOS_Pos) /*!< 0x00000004 */ +#define ADC_SR_JEOS ADC_SR_JEOS_Msk /*!< ADC group injected end of sequence conversions flag */ +#define ADC_SR_JSTRT_Pos (3U) +#define ADC_SR_JSTRT_Msk (0x1UL << ADC_SR_JSTRT_Pos) /*!< 0x00000008 */ +#define ADC_SR_JSTRT ADC_SR_JSTRT_Msk /*!< ADC group injected conversion start flag */ +#define ADC_SR_STRT_Pos (4U) +#define ADC_SR_STRT_Msk (0x1UL << ADC_SR_STRT_Pos) /*!< 0x00000010 */ +#define ADC_SR_STRT ADC_SR_STRT_Msk /*!< ADC group regular conversion start flag */ + +/* Legacy defines */ +#define ADC_SR_EOC (ADC_SR_EOS) +#define ADC_SR_JEOC (ADC_SR_JEOS) + +/******************* Bit definition for ADC_CR1 register ********************/ +#define ADC_CR1_AWDCH_Pos (0U) +#define ADC_CR1_AWDCH_Msk (0x1FUL << ADC_CR1_AWDCH_Pos) /*!< 0x0000001F */ +#define ADC_CR1_AWDCH ADC_CR1_AWDCH_Msk /*!< ADC analog watchdog 1 monitored channel selection */ +#define ADC_CR1_AWDCH_0 (0x01UL << ADC_CR1_AWDCH_Pos) /*!< 0x00000001 */ +#define ADC_CR1_AWDCH_1 (0x02UL << ADC_CR1_AWDCH_Pos) /*!< 0x00000002 */ +#define ADC_CR1_AWDCH_2 (0x04UL << ADC_CR1_AWDCH_Pos) /*!< 0x00000004 */ +#define ADC_CR1_AWDCH_3 (0x08UL << ADC_CR1_AWDCH_Pos) /*!< 0x00000008 */ +#define ADC_CR1_AWDCH_4 (0x10UL << ADC_CR1_AWDCH_Pos) /*!< 0x00000010 */ + +#define ADC_CR1_EOSIE_Pos (5U) +#define ADC_CR1_EOSIE_Msk (0x1UL << ADC_CR1_EOSIE_Pos) /*!< 0x00000020 */ +#define ADC_CR1_EOSIE ADC_CR1_EOSIE_Msk /*!< ADC group regular end of sequence conversions interrupt */ +#define ADC_CR1_AWDIE_Pos (6U) +#define ADC_CR1_AWDIE_Msk (0x1UL << ADC_CR1_AWDIE_Pos) /*!< 0x00000040 */ +#define ADC_CR1_AWDIE ADC_CR1_AWDIE_Msk /*!< ADC analog watchdog 1 interrupt */ +#define ADC_CR1_JEOSIE_Pos (7U) +#define ADC_CR1_JEOSIE_Msk (0x1UL << ADC_CR1_JEOSIE_Pos) /*!< 0x00000080 */ +#define ADC_CR1_JEOSIE ADC_CR1_JEOSIE_Msk /*!< ADC group injected end of sequence conversions interrupt */ +#define ADC_CR1_SCAN_Pos (8U) +#define ADC_CR1_SCAN_Msk (0x1UL << ADC_CR1_SCAN_Pos) /*!< 0x00000100 */ +#define ADC_CR1_SCAN ADC_CR1_SCAN_Msk /*!< ADC scan mode */ +#define ADC_CR1_AWDSGL_Pos (9U) +#define ADC_CR1_AWDSGL_Msk (0x1UL << ADC_CR1_AWDSGL_Pos) /*!< 0x00000200 */ +#define ADC_CR1_AWDSGL ADC_CR1_AWDSGL_Msk /*!< ADC analog watchdog 1 monitoring a single channel or all channels */ +#define ADC_CR1_JAUTO_Pos (10U) +#define ADC_CR1_JAUTO_Msk (0x1UL << ADC_CR1_JAUTO_Pos) /*!< 0x00000400 */ +#define ADC_CR1_JAUTO ADC_CR1_JAUTO_Msk /*!< ADC group injected automatic trigger mode */ +#define ADC_CR1_DISCEN_Pos (11U) +#define ADC_CR1_DISCEN_Msk (0x1UL << ADC_CR1_DISCEN_Pos) /*!< 0x00000800 */ +#define ADC_CR1_DISCEN ADC_CR1_DISCEN_Msk /*!< ADC group regular sequencer discontinuous mode */ +#define ADC_CR1_JDISCEN_Pos (12U) +#define ADC_CR1_JDISCEN_Msk (0x1UL << ADC_CR1_JDISCEN_Pos) /*!< 0x00001000 */ +#define ADC_CR1_JDISCEN ADC_CR1_JDISCEN_Msk /*!< ADC group injected sequencer discontinuous mode */ + +#define ADC_CR1_DISCNUM_Pos (13U) +#define ADC_CR1_DISCNUM_Msk (0x7UL << ADC_CR1_DISCNUM_Pos) /*!< 0x0000E000 */ +#define ADC_CR1_DISCNUM ADC_CR1_DISCNUM_Msk /*!< ADC group regular sequencer discontinuous number of ranks */ +#define ADC_CR1_DISCNUM_0 (0x1UL << ADC_CR1_DISCNUM_Pos) /*!< 0x00002000 */ +#define ADC_CR1_DISCNUM_1 (0x2UL << ADC_CR1_DISCNUM_Pos) /*!< 0x00004000 */ +#define ADC_CR1_DISCNUM_2 (0x4UL << ADC_CR1_DISCNUM_Pos) /*!< 0x00008000 */ + +#define ADC_CR1_DUALMOD_Pos (16U) +#define ADC_CR1_DUALMOD_Msk (0xFUL << ADC_CR1_DUALMOD_Pos) /*!< 0x000F0000 */ +#define ADC_CR1_DUALMOD ADC_CR1_DUALMOD_Msk /*!< ADC multimode mode selection */ +#define ADC_CR1_DUALMOD_0 (0x1UL << ADC_CR1_DUALMOD_Pos) /*!< 0x00010000 */ +#define ADC_CR1_DUALMOD_1 (0x2UL << ADC_CR1_DUALMOD_Pos) /*!< 0x00020000 */ +#define ADC_CR1_DUALMOD_2 (0x4UL << ADC_CR1_DUALMOD_Pos) /*!< 0x00040000 */ +#define ADC_CR1_DUALMOD_3 (0x8UL << ADC_CR1_DUALMOD_Pos) /*!< 0x00080000 */ + +#define ADC_CR1_JAWDEN_Pos (22U) +#define ADC_CR1_JAWDEN_Msk (0x1UL << ADC_CR1_JAWDEN_Pos) /*!< 0x00400000 */ +#define ADC_CR1_JAWDEN ADC_CR1_JAWDEN_Msk /*!< ADC analog watchdog 1 enable on scope ADC group injected */ +#define ADC_CR1_AWDEN_Pos (23U) +#define ADC_CR1_AWDEN_Msk (0x1UL << ADC_CR1_AWDEN_Pos) /*!< 0x00800000 */ +#define ADC_CR1_AWDEN ADC_CR1_AWDEN_Msk /*!< ADC analog watchdog 1 enable on scope ADC group regular */ + +/* Legacy defines */ +#define ADC_CR1_EOCIE (ADC_CR1_EOSIE) +#define ADC_CR1_JEOCIE (ADC_CR1_JEOSIE) + +/******************* Bit definition for ADC_CR2 register ********************/ +#define ADC_CR2_ADON_Pos (0U) +#define ADC_CR2_ADON_Msk (0x1UL << ADC_CR2_ADON_Pos) /*!< 0x00000001 */ +#define ADC_CR2_ADON ADC_CR2_ADON_Msk /*!< ADC enable */ +#define ADC_CR2_CONT_Pos (1U) +#define ADC_CR2_CONT_Msk (0x1UL << ADC_CR2_CONT_Pos) /*!< 0x00000002 */ +#define ADC_CR2_CONT ADC_CR2_CONT_Msk /*!< ADC group regular continuous conversion mode */ +#define ADC_CR2_CAL_Pos (2U) +#define ADC_CR2_CAL_Msk (0x1UL << ADC_CR2_CAL_Pos) /*!< 0x00000004 */ +#define ADC_CR2_CAL ADC_CR2_CAL_Msk /*!< ADC calibration start */ +#define ADC_CR2_RSTCAL_Pos (3U) +#define ADC_CR2_RSTCAL_Msk (0x1UL << ADC_CR2_RSTCAL_Pos) /*!< 0x00000008 */ +#define ADC_CR2_RSTCAL ADC_CR2_RSTCAL_Msk /*!< ADC calibration reset */ +#define ADC_CR2_DMA_Pos (8U) +#define ADC_CR2_DMA_Msk (0x1UL << ADC_CR2_DMA_Pos) /*!< 0x00000100 */ +#define ADC_CR2_DMA ADC_CR2_DMA_Msk /*!< ADC DMA transfer enable */ +#define ADC_CR2_ALIGN_Pos (11U) +#define ADC_CR2_ALIGN_Msk (0x1UL << ADC_CR2_ALIGN_Pos) /*!< 0x00000800 */ +#define ADC_CR2_ALIGN ADC_CR2_ALIGN_Msk /*!< ADC data alignement */ + +#define ADC_CR2_JEXTSEL_Pos (12U) +#define ADC_CR2_JEXTSEL_Msk (0x7UL << ADC_CR2_JEXTSEL_Pos) /*!< 0x00007000 */ +#define ADC_CR2_JEXTSEL ADC_CR2_JEXTSEL_Msk /*!< ADC group injected external trigger source */ +#define ADC_CR2_JEXTSEL_0 (0x1UL << ADC_CR2_JEXTSEL_Pos) /*!< 0x00001000 */ +#define ADC_CR2_JEXTSEL_1 (0x2UL << ADC_CR2_JEXTSEL_Pos) /*!< 0x00002000 */ +#define ADC_CR2_JEXTSEL_2 (0x4UL << ADC_CR2_JEXTSEL_Pos) /*!< 0x00004000 */ + +#define ADC_CR2_JEXTTRIG_Pos (15U) +#define ADC_CR2_JEXTTRIG_Msk (0x1UL << ADC_CR2_JEXTTRIG_Pos) /*!< 0x00008000 */ +#define ADC_CR2_JEXTTRIG ADC_CR2_JEXTTRIG_Msk /*!< ADC group injected external trigger enable */ + +#define ADC_CR2_EXTSEL_Pos (17U) +#define ADC_CR2_EXTSEL_Msk (0x7UL << ADC_CR2_EXTSEL_Pos) /*!< 0x000E0000 */ +#define ADC_CR2_EXTSEL ADC_CR2_EXTSEL_Msk /*!< ADC group regular external trigger source */ +#define ADC_CR2_EXTSEL_0 (0x1UL << ADC_CR2_EXTSEL_Pos) /*!< 0x00020000 */ +#define ADC_CR2_EXTSEL_1 (0x2UL << ADC_CR2_EXTSEL_Pos) /*!< 0x00040000 */ +#define ADC_CR2_EXTSEL_2 (0x4UL << ADC_CR2_EXTSEL_Pos) /*!< 0x00080000 */ + +#define ADC_CR2_EXTTRIG_Pos (20U) +#define ADC_CR2_EXTTRIG_Msk (0x1UL << ADC_CR2_EXTTRIG_Pos) /*!< 0x00100000 */ +#define ADC_CR2_EXTTRIG ADC_CR2_EXTTRIG_Msk /*!< ADC group regular external trigger enable */ +#define ADC_CR2_JSWSTART_Pos (21U) +#define ADC_CR2_JSWSTART_Msk (0x1UL << ADC_CR2_JSWSTART_Pos) /*!< 0x00200000 */ +#define ADC_CR2_JSWSTART ADC_CR2_JSWSTART_Msk /*!< ADC group injected conversion start */ +#define ADC_CR2_SWSTART_Pos (22U) +#define ADC_CR2_SWSTART_Msk (0x1UL << ADC_CR2_SWSTART_Pos) /*!< 0x00400000 */ +#define ADC_CR2_SWSTART ADC_CR2_SWSTART_Msk /*!< ADC group regular conversion start */ +#define ADC_CR2_TSVREFE_Pos (23U) +#define ADC_CR2_TSVREFE_Msk (0x1UL << ADC_CR2_TSVREFE_Pos) /*!< 0x00800000 */ +#define ADC_CR2_TSVREFE ADC_CR2_TSVREFE_Msk /*!< ADC internal path to VrefInt and temperature sensor enable */ + +/****************** Bit definition for ADC_SMPR1 register *******************/ +#define ADC_SMPR1_SMP10_Pos (0U) +#define ADC_SMPR1_SMP10_Msk (0x7UL << ADC_SMPR1_SMP10_Pos) /*!< 0x00000007 */ +#define ADC_SMPR1_SMP10 ADC_SMPR1_SMP10_Msk /*!< ADC channel 10 sampling time selection */ +#define ADC_SMPR1_SMP10_0 (0x1UL << ADC_SMPR1_SMP10_Pos) /*!< 0x00000001 */ +#define ADC_SMPR1_SMP10_1 (0x2UL << ADC_SMPR1_SMP10_Pos) /*!< 0x00000002 */ +#define ADC_SMPR1_SMP10_2 (0x4UL << ADC_SMPR1_SMP10_Pos) /*!< 0x00000004 */ + +#define ADC_SMPR1_SMP11_Pos (3U) +#define ADC_SMPR1_SMP11_Msk (0x7UL << ADC_SMPR1_SMP11_Pos) /*!< 0x00000038 */ +#define ADC_SMPR1_SMP11 ADC_SMPR1_SMP11_Msk /*!< ADC channel 11 sampling time selection */ +#define ADC_SMPR1_SMP11_0 (0x1UL << ADC_SMPR1_SMP11_Pos) /*!< 0x00000008 */ +#define ADC_SMPR1_SMP11_1 (0x2UL << ADC_SMPR1_SMP11_Pos) /*!< 0x00000010 */ +#define ADC_SMPR1_SMP11_2 (0x4UL << ADC_SMPR1_SMP11_Pos) /*!< 0x00000020 */ + +#define ADC_SMPR1_SMP12_Pos (6U) +#define ADC_SMPR1_SMP12_Msk (0x7UL << ADC_SMPR1_SMP12_Pos) /*!< 0x000001C0 */ +#define ADC_SMPR1_SMP12 ADC_SMPR1_SMP12_Msk /*!< ADC channel 12 sampling time selection */ +#define ADC_SMPR1_SMP12_0 (0x1UL << ADC_SMPR1_SMP12_Pos) /*!< 0x00000040 */ +#define ADC_SMPR1_SMP12_1 (0x2UL << ADC_SMPR1_SMP12_Pos) /*!< 0x00000080 */ +#define ADC_SMPR1_SMP12_2 (0x4UL << ADC_SMPR1_SMP12_Pos) /*!< 0x00000100 */ + +#define ADC_SMPR1_SMP13_Pos (9U) +#define ADC_SMPR1_SMP13_Msk (0x7UL << ADC_SMPR1_SMP13_Pos) /*!< 0x00000E00 */ +#define ADC_SMPR1_SMP13 ADC_SMPR1_SMP13_Msk /*!< ADC channel 13 sampling time selection */ +#define ADC_SMPR1_SMP13_0 (0x1UL << ADC_SMPR1_SMP13_Pos) /*!< 0x00000200 */ +#define ADC_SMPR1_SMP13_1 (0x2UL << ADC_SMPR1_SMP13_Pos) /*!< 0x00000400 */ +#define ADC_SMPR1_SMP13_2 (0x4UL << ADC_SMPR1_SMP13_Pos) /*!< 0x00000800 */ + +#define ADC_SMPR1_SMP14_Pos (12U) +#define ADC_SMPR1_SMP14_Msk (0x7UL << ADC_SMPR1_SMP14_Pos) /*!< 0x00007000 */ +#define ADC_SMPR1_SMP14 ADC_SMPR1_SMP14_Msk /*!< ADC channel 14 sampling time selection */ +#define ADC_SMPR1_SMP14_0 (0x1UL << ADC_SMPR1_SMP14_Pos) /*!< 0x00001000 */ +#define ADC_SMPR1_SMP14_1 (0x2UL << ADC_SMPR1_SMP14_Pos) /*!< 0x00002000 */ +#define ADC_SMPR1_SMP14_2 (0x4UL << ADC_SMPR1_SMP14_Pos) /*!< 0x00004000 */ + +#define ADC_SMPR1_SMP15_Pos (15U) +#define ADC_SMPR1_SMP15_Msk (0x7UL << ADC_SMPR1_SMP15_Pos) /*!< 0x00038000 */ +#define ADC_SMPR1_SMP15 ADC_SMPR1_SMP15_Msk /*!< ADC channel 15 sampling time selection */ +#define ADC_SMPR1_SMP15_0 (0x1UL << ADC_SMPR1_SMP15_Pos) /*!< 0x00008000 */ +#define ADC_SMPR1_SMP15_1 (0x2UL << ADC_SMPR1_SMP15_Pos) /*!< 0x00010000 */ +#define ADC_SMPR1_SMP15_2 (0x4UL << ADC_SMPR1_SMP15_Pos) /*!< 0x00020000 */ + +#define ADC_SMPR1_SMP16_Pos (18U) +#define ADC_SMPR1_SMP16_Msk (0x7UL << ADC_SMPR1_SMP16_Pos) /*!< 0x001C0000 */ +#define ADC_SMPR1_SMP16 ADC_SMPR1_SMP16_Msk /*!< ADC channel 16 sampling time selection */ +#define ADC_SMPR1_SMP16_0 (0x1UL << ADC_SMPR1_SMP16_Pos) /*!< 0x00040000 */ +#define ADC_SMPR1_SMP16_1 (0x2UL << ADC_SMPR1_SMP16_Pos) /*!< 0x00080000 */ +#define ADC_SMPR1_SMP16_2 (0x4UL << ADC_SMPR1_SMP16_Pos) /*!< 0x00100000 */ + +#define ADC_SMPR1_SMP17_Pos (21U) +#define ADC_SMPR1_SMP17_Msk (0x7UL << ADC_SMPR1_SMP17_Pos) /*!< 0x00E00000 */ +#define ADC_SMPR1_SMP17 ADC_SMPR1_SMP17_Msk /*!< ADC channel 17 sampling time selection */ +#define ADC_SMPR1_SMP17_0 (0x1UL << ADC_SMPR1_SMP17_Pos) /*!< 0x00200000 */ +#define ADC_SMPR1_SMP17_1 (0x2UL << ADC_SMPR1_SMP17_Pos) /*!< 0x00400000 */ +#define ADC_SMPR1_SMP17_2 (0x4UL << ADC_SMPR1_SMP17_Pos) /*!< 0x00800000 */ + +/****************** Bit definition for ADC_SMPR2 register *******************/ +#define ADC_SMPR2_SMP0_Pos (0U) +#define ADC_SMPR2_SMP0_Msk (0x7UL << ADC_SMPR2_SMP0_Pos) /*!< 0x00000007 */ +#define ADC_SMPR2_SMP0 ADC_SMPR2_SMP0_Msk /*!< ADC channel 0 sampling time selection */ +#define ADC_SMPR2_SMP0_0 (0x1UL << ADC_SMPR2_SMP0_Pos) /*!< 0x00000001 */ +#define ADC_SMPR2_SMP0_1 (0x2UL << ADC_SMPR2_SMP0_Pos) /*!< 0x00000002 */ +#define ADC_SMPR2_SMP0_2 (0x4UL << ADC_SMPR2_SMP0_Pos) /*!< 0x00000004 */ + +#define ADC_SMPR2_SMP1_Pos (3U) +#define ADC_SMPR2_SMP1_Msk (0x7UL << ADC_SMPR2_SMP1_Pos) /*!< 0x00000038 */ +#define ADC_SMPR2_SMP1 ADC_SMPR2_SMP1_Msk /*!< ADC channel 1 sampling time selection */ +#define ADC_SMPR2_SMP1_0 (0x1UL << ADC_SMPR2_SMP1_Pos) /*!< 0x00000008 */ +#define ADC_SMPR2_SMP1_1 (0x2UL << ADC_SMPR2_SMP1_Pos) /*!< 0x00000010 */ +#define ADC_SMPR2_SMP1_2 (0x4UL << ADC_SMPR2_SMP1_Pos) /*!< 0x00000020 */ + +#define ADC_SMPR2_SMP2_Pos (6U) +#define ADC_SMPR2_SMP2_Msk (0x7UL << ADC_SMPR2_SMP2_Pos) /*!< 0x000001C0 */ +#define ADC_SMPR2_SMP2 ADC_SMPR2_SMP2_Msk /*!< ADC channel 2 sampling time selection */ +#define ADC_SMPR2_SMP2_0 (0x1UL << ADC_SMPR2_SMP2_Pos) /*!< 0x00000040 */ +#define ADC_SMPR2_SMP2_1 (0x2UL << ADC_SMPR2_SMP2_Pos) /*!< 0x00000080 */ +#define ADC_SMPR2_SMP2_2 (0x4UL << ADC_SMPR2_SMP2_Pos) /*!< 0x00000100 */ + +#define ADC_SMPR2_SMP3_Pos (9U) +#define ADC_SMPR2_SMP3_Msk (0x7UL << ADC_SMPR2_SMP3_Pos) /*!< 0x00000E00 */ +#define ADC_SMPR2_SMP3 ADC_SMPR2_SMP3_Msk /*!< ADC channel 3 sampling time selection */ +#define ADC_SMPR2_SMP3_0 (0x1UL << ADC_SMPR2_SMP3_Pos) /*!< 0x00000200 */ +#define ADC_SMPR2_SMP3_1 (0x2UL << ADC_SMPR2_SMP3_Pos) /*!< 0x00000400 */ +#define ADC_SMPR2_SMP3_2 (0x4UL << ADC_SMPR2_SMP3_Pos) /*!< 0x00000800 */ + +#define ADC_SMPR2_SMP4_Pos (12U) +#define ADC_SMPR2_SMP4_Msk (0x7UL << ADC_SMPR2_SMP4_Pos) /*!< 0x00007000 */ +#define ADC_SMPR2_SMP4 ADC_SMPR2_SMP4_Msk /*!< ADC channel 4 sampling time selection */ +#define ADC_SMPR2_SMP4_0 (0x1UL << ADC_SMPR2_SMP4_Pos) /*!< 0x00001000 */ +#define ADC_SMPR2_SMP4_1 (0x2UL << ADC_SMPR2_SMP4_Pos) /*!< 0x00002000 */ +#define ADC_SMPR2_SMP4_2 (0x4UL << ADC_SMPR2_SMP4_Pos) /*!< 0x00004000 */ + +#define ADC_SMPR2_SMP5_Pos (15U) +#define ADC_SMPR2_SMP5_Msk (0x7UL << ADC_SMPR2_SMP5_Pos) /*!< 0x00038000 */ +#define ADC_SMPR2_SMP5 ADC_SMPR2_SMP5_Msk /*!< ADC channel 5 sampling time selection */ +#define ADC_SMPR2_SMP5_0 (0x1UL << ADC_SMPR2_SMP5_Pos) /*!< 0x00008000 */ +#define ADC_SMPR2_SMP5_1 (0x2UL << ADC_SMPR2_SMP5_Pos) /*!< 0x00010000 */ +#define ADC_SMPR2_SMP5_2 (0x4UL << ADC_SMPR2_SMP5_Pos) /*!< 0x00020000 */ + +#define ADC_SMPR2_SMP6_Pos (18U) +#define ADC_SMPR2_SMP6_Msk (0x7UL << ADC_SMPR2_SMP6_Pos) /*!< 0x001C0000 */ +#define ADC_SMPR2_SMP6 ADC_SMPR2_SMP6_Msk /*!< ADC channel 6 sampling time selection */ +#define ADC_SMPR2_SMP6_0 (0x1UL << ADC_SMPR2_SMP6_Pos) /*!< 0x00040000 */ +#define ADC_SMPR2_SMP6_1 (0x2UL << ADC_SMPR2_SMP6_Pos) /*!< 0x00080000 */ +#define ADC_SMPR2_SMP6_2 (0x4UL << ADC_SMPR2_SMP6_Pos) /*!< 0x00100000 */ + +#define ADC_SMPR2_SMP7_Pos (21U) +#define ADC_SMPR2_SMP7_Msk (0x7UL << ADC_SMPR2_SMP7_Pos) /*!< 0x00E00000 */ +#define ADC_SMPR2_SMP7 ADC_SMPR2_SMP7_Msk /*!< ADC channel 7 sampling time selection */ +#define ADC_SMPR2_SMP7_0 (0x1UL << ADC_SMPR2_SMP7_Pos) /*!< 0x00200000 */ +#define ADC_SMPR2_SMP7_1 (0x2UL << ADC_SMPR2_SMP7_Pos) /*!< 0x00400000 */ +#define ADC_SMPR2_SMP7_2 (0x4UL << ADC_SMPR2_SMP7_Pos) /*!< 0x00800000 */ + +#define ADC_SMPR2_SMP8_Pos (24U) +#define ADC_SMPR2_SMP8_Msk (0x7UL << ADC_SMPR2_SMP8_Pos) /*!< 0x07000000 */ +#define ADC_SMPR2_SMP8 ADC_SMPR2_SMP8_Msk /*!< ADC channel 8 sampling time selection */ +#define ADC_SMPR2_SMP8_0 (0x1UL << ADC_SMPR2_SMP8_Pos) /*!< 0x01000000 */ +#define ADC_SMPR2_SMP8_1 (0x2UL << ADC_SMPR2_SMP8_Pos) /*!< 0x02000000 */ +#define ADC_SMPR2_SMP8_2 (0x4UL << ADC_SMPR2_SMP8_Pos) /*!< 0x04000000 */ + +#define ADC_SMPR2_SMP9_Pos (27U) +#define ADC_SMPR2_SMP9_Msk (0x7UL << ADC_SMPR2_SMP9_Pos) /*!< 0x38000000 */ +#define ADC_SMPR2_SMP9 ADC_SMPR2_SMP9_Msk /*!< ADC channel 9 sampling time selection */ +#define ADC_SMPR2_SMP9_0 (0x1UL << ADC_SMPR2_SMP9_Pos) /*!< 0x08000000 */ +#define ADC_SMPR2_SMP9_1 (0x2UL << ADC_SMPR2_SMP9_Pos) /*!< 0x10000000 */ +#define ADC_SMPR2_SMP9_2 (0x4UL << ADC_SMPR2_SMP9_Pos) /*!< 0x20000000 */ + +/****************** Bit definition for ADC_JOFR1 register *******************/ +#define ADC_JOFR1_JOFFSET1_Pos (0U) +#define ADC_JOFR1_JOFFSET1_Msk (0xFFFUL << ADC_JOFR1_JOFFSET1_Pos) /*!< 0x00000FFF */ +#define ADC_JOFR1_JOFFSET1 ADC_JOFR1_JOFFSET1_Msk /*!< ADC group injected sequencer rank 1 offset value */ + +/****************** Bit definition for ADC_JOFR2 register *******************/ +#define ADC_JOFR2_JOFFSET2_Pos (0U) +#define ADC_JOFR2_JOFFSET2_Msk (0xFFFUL << ADC_JOFR2_JOFFSET2_Pos) /*!< 0x00000FFF */ +#define ADC_JOFR2_JOFFSET2 ADC_JOFR2_JOFFSET2_Msk /*!< ADC group injected sequencer rank 2 offset value */ + +/****************** Bit definition for ADC_JOFR3 register *******************/ +#define ADC_JOFR3_JOFFSET3_Pos (0U) +#define ADC_JOFR3_JOFFSET3_Msk (0xFFFUL << ADC_JOFR3_JOFFSET3_Pos) /*!< 0x00000FFF */ +#define ADC_JOFR3_JOFFSET3 ADC_JOFR3_JOFFSET3_Msk /*!< ADC group injected sequencer rank 3 offset value */ + +/****************** Bit definition for ADC_JOFR4 register *******************/ +#define ADC_JOFR4_JOFFSET4_Pos (0U) +#define ADC_JOFR4_JOFFSET4_Msk (0xFFFUL << ADC_JOFR4_JOFFSET4_Pos) /*!< 0x00000FFF */ +#define ADC_JOFR4_JOFFSET4 ADC_JOFR4_JOFFSET4_Msk /*!< ADC group injected sequencer rank 4 offset value */ + +/******************* Bit definition for ADC_HTR register ********************/ +#define ADC_HTR_HT_Pos (0U) +#define ADC_HTR_HT_Msk (0xFFFUL << ADC_HTR_HT_Pos) /*!< 0x00000FFF */ +#define ADC_HTR_HT ADC_HTR_HT_Msk /*!< ADC analog watchdog 1 threshold high */ + +/******************* Bit definition for ADC_LTR register ********************/ +#define ADC_LTR_LT_Pos (0U) +#define ADC_LTR_LT_Msk (0xFFFUL << ADC_LTR_LT_Pos) /*!< 0x00000FFF */ +#define ADC_LTR_LT ADC_LTR_LT_Msk /*!< ADC analog watchdog 1 threshold low */ + +/******************* Bit definition for ADC_SQR1 register *******************/ +#define ADC_SQR1_SQ13_Pos (0U) +#define ADC_SQR1_SQ13_Msk (0x1FUL << ADC_SQR1_SQ13_Pos) /*!< 0x0000001F */ +#define ADC_SQR1_SQ13 ADC_SQR1_SQ13_Msk /*!< ADC group regular sequencer rank 13 */ +#define ADC_SQR1_SQ13_0 (0x01UL << ADC_SQR1_SQ13_Pos) /*!< 0x00000001 */ +#define ADC_SQR1_SQ13_1 (0x02UL << ADC_SQR1_SQ13_Pos) /*!< 0x00000002 */ +#define ADC_SQR1_SQ13_2 (0x04UL << ADC_SQR1_SQ13_Pos) /*!< 0x00000004 */ +#define ADC_SQR1_SQ13_3 (0x08UL << ADC_SQR1_SQ13_Pos) /*!< 0x00000008 */ +#define ADC_SQR1_SQ13_4 (0x10UL << ADC_SQR1_SQ13_Pos) /*!< 0x00000010 */ + +#define ADC_SQR1_SQ14_Pos (5U) +#define ADC_SQR1_SQ14_Msk (0x1FUL << ADC_SQR1_SQ14_Pos) /*!< 0x000003E0 */ +#define ADC_SQR1_SQ14 ADC_SQR1_SQ14_Msk /*!< ADC group regular sequencer rank 14 */ +#define ADC_SQR1_SQ14_0 (0x01UL << ADC_SQR1_SQ14_Pos) /*!< 0x00000020 */ +#define ADC_SQR1_SQ14_1 (0x02UL << ADC_SQR1_SQ14_Pos) /*!< 0x00000040 */ +#define ADC_SQR1_SQ14_2 (0x04UL << ADC_SQR1_SQ14_Pos) /*!< 0x00000080 */ +#define ADC_SQR1_SQ14_3 (0x08UL << ADC_SQR1_SQ14_Pos) /*!< 0x00000100 */ +#define ADC_SQR1_SQ14_4 (0x10UL << ADC_SQR1_SQ14_Pos) /*!< 0x00000200 */ + +#define ADC_SQR1_SQ15_Pos (10U) +#define ADC_SQR1_SQ15_Msk (0x1FUL << ADC_SQR1_SQ15_Pos) /*!< 0x00007C00 */ +#define ADC_SQR1_SQ15 ADC_SQR1_SQ15_Msk /*!< ADC group regular sequencer rank 15 */ +#define ADC_SQR1_SQ15_0 (0x01UL << ADC_SQR1_SQ15_Pos) /*!< 0x00000400 */ +#define ADC_SQR1_SQ15_1 (0x02UL << ADC_SQR1_SQ15_Pos) /*!< 0x00000800 */ +#define ADC_SQR1_SQ15_2 (0x04UL << ADC_SQR1_SQ15_Pos) /*!< 0x00001000 */ +#define ADC_SQR1_SQ15_3 (0x08UL << ADC_SQR1_SQ15_Pos) /*!< 0x00002000 */ +#define ADC_SQR1_SQ15_4 (0x10UL << ADC_SQR1_SQ15_Pos) /*!< 0x00004000 */ + +#define ADC_SQR1_SQ16_Pos (15U) +#define ADC_SQR1_SQ16_Msk (0x1FUL << ADC_SQR1_SQ16_Pos) /*!< 0x000F8000 */ +#define ADC_SQR1_SQ16 ADC_SQR1_SQ16_Msk /*!< ADC group regular sequencer rank 16 */ +#define ADC_SQR1_SQ16_0 (0x01UL << ADC_SQR1_SQ16_Pos) /*!< 0x00008000 */ +#define ADC_SQR1_SQ16_1 (0x02UL << ADC_SQR1_SQ16_Pos) /*!< 0x00010000 */ +#define ADC_SQR1_SQ16_2 (0x04UL << ADC_SQR1_SQ16_Pos) /*!< 0x00020000 */ +#define ADC_SQR1_SQ16_3 (0x08UL << ADC_SQR1_SQ16_Pos) /*!< 0x00040000 */ +#define ADC_SQR1_SQ16_4 (0x10UL << ADC_SQR1_SQ16_Pos) /*!< 0x00080000 */ + +#define ADC_SQR1_L_Pos (20U) +#define ADC_SQR1_L_Msk (0xFUL << ADC_SQR1_L_Pos) /*!< 0x00F00000 */ +#define ADC_SQR1_L ADC_SQR1_L_Msk /*!< ADC group regular sequencer scan length */ +#define ADC_SQR1_L_0 (0x1UL << ADC_SQR1_L_Pos) /*!< 0x00100000 */ +#define ADC_SQR1_L_1 (0x2UL << ADC_SQR1_L_Pos) /*!< 0x00200000 */ +#define ADC_SQR1_L_2 (0x4UL << ADC_SQR1_L_Pos) /*!< 0x00400000 */ +#define ADC_SQR1_L_3 (0x8UL << ADC_SQR1_L_Pos) /*!< 0x00800000 */ + +/******************* Bit definition for ADC_SQR2 register *******************/ +#define ADC_SQR2_SQ7_Pos (0U) +#define ADC_SQR2_SQ7_Msk (0x1FUL << ADC_SQR2_SQ7_Pos) /*!< 0x0000001F */ +#define ADC_SQR2_SQ7 ADC_SQR2_SQ7_Msk /*!< ADC group regular sequencer rank 7 */ +#define ADC_SQR2_SQ7_0 (0x01UL << ADC_SQR2_SQ7_Pos) /*!< 0x00000001 */ +#define ADC_SQR2_SQ7_1 (0x02UL << ADC_SQR2_SQ7_Pos) /*!< 0x00000002 */ +#define ADC_SQR2_SQ7_2 (0x04UL << ADC_SQR2_SQ7_Pos) /*!< 0x00000004 */ +#define ADC_SQR2_SQ7_3 (0x08UL << ADC_SQR2_SQ7_Pos) /*!< 0x00000008 */ +#define ADC_SQR2_SQ7_4 (0x10UL << ADC_SQR2_SQ7_Pos) /*!< 0x00000010 */ + +#define ADC_SQR2_SQ8_Pos (5U) +#define ADC_SQR2_SQ8_Msk (0x1FUL << ADC_SQR2_SQ8_Pos) /*!< 0x000003E0 */ +#define ADC_SQR2_SQ8 ADC_SQR2_SQ8_Msk /*!< ADC group regular sequencer rank 8 */ +#define ADC_SQR2_SQ8_0 (0x01UL << ADC_SQR2_SQ8_Pos) /*!< 0x00000020 */ +#define ADC_SQR2_SQ8_1 (0x02UL << ADC_SQR2_SQ8_Pos) /*!< 0x00000040 */ +#define ADC_SQR2_SQ8_2 (0x04UL << ADC_SQR2_SQ8_Pos) /*!< 0x00000080 */ +#define ADC_SQR2_SQ8_3 (0x08UL << ADC_SQR2_SQ8_Pos) /*!< 0x00000100 */ +#define ADC_SQR2_SQ8_4 (0x10UL << ADC_SQR2_SQ8_Pos) /*!< 0x00000200 */ + +#define ADC_SQR2_SQ9_Pos (10U) +#define ADC_SQR2_SQ9_Msk (0x1FUL << ADC_SQR2_SQ9_Pos) /*!< 0x00007C00 */ +#define ADC_SQR2_SQ9 ADC_SQR2_SQ9_Msk /*!< ADC group regular sequencer rank 9 */ +#define ADC_SQR2_SQ9_0 (0x01UL << ADC_SQR2_SQ9_Pos) /*!< 0x00000400 */ +#define ADC_SQR2_SQ9_1 (0x02UL << ADC_SQR2_SQ9_Pos) /*!< 0x00000800 */ +#define ADC_SQR2_SQ9_2 (0x04UL << ADC_SQR2_SQ9_Pos) /*!< 0x00001000 */ +#define ADC_SQR2_SQ9_3 (0x08UL << ADC_SQR2_SQ9_Pos) /*!< 0x00002000 */ +#define ADC_SQR2_SQ9_4 (0x10UL << ADC_SQR2_SQ9_Pos) /*!< 0x00004000 */ + +#define ADC_SQR2_SQ10_Pos (15U) +#define ADC_SQR2_SQ10_Msk (0x1FUL << ADC_SQR2_SQ10_Pos) /*!< 0x000F8000 */ +#define ADC_SQR2_SQ10 ADC_SQR2_SQ10_Msk /*!< ADC group regular sequencer rank 10 */ +#define ADC_SQR2_SQ10_0 (0x01UL << ADC_SQR2_SQ10_Pos) /*!< 0x00008000 */ +#define ADC_SQR2_SQ10_1 (0x02UL << ADC_SQR2_SQ10_Pos) /*!< 0x00010000 */ +#define ADC_SQR2_SQ10_2 (0x04UL << ADC_SQR2_SQ10_Pos) /*!< 0x00020000 */ +#define ADC_SQR2_SQ10_3 (0x08UL << ADC_SQR2_SQ10_Pos) /*!< 0x00040000 */ +#define ADC_SQR2_SQ10_4 (0x10UL << ADC_SQR2_SQ10_Pos) /*!< 0x00080000 */ + +#define ADC_SQR2_SQ11_Pos (20U) +#define ADC_SQR2_SQ11_Msk (0x1FUL << ADC_SQR2_SQ11_Pos) /*!< 0x01F00000 */ +#define ADC_SQR2_SQ11 ADC_SQR2_SQ11_Msk /*!< ADC group regular sequencer rank 1 */ +#define ADC_SQR2_SQ11_0 (0x01UL << ADC_SQR2_SQ11_Pos) /*!< 0x00100000 */ +#define ADC_SQR2_SQ11_1 (0x02UL << ADC_SQR2_SQ11_Pos) /*!< 0x00200000 */ +#define ADC_SQR2_SQ11_2 (0x04UL << ADC_SQR2_SQ11_Pos) /*!< 0x00400000 */ +#define ADC_SQR2_SQ11_3 (0x08UL << ADC_SQR2_SQ11_Pos) /*!< 0x00800000 */ +#define ADC_SQR2_SQ11_4 (0x10UL << ADC_SQR2_SQ11_Pos) /*!< 0x01000000 */ + +#define ADC_SQR2_SQ12_Pos (25U) +#define ADC_SQR2_SQ12_Msk (0x1FUL << ADC_SQR2_SQ12_Pos) /*!< 0x3E000000 */ +#define ADC_SQR2_SQ12 ADC_SQR2_SQ12_Msk /*!< ADC group regular sequencer rank 12 */ +#define ADC_SQR2_SQ12_0 (0x01UL << ADC_SQR2_SQ12_Pos) /*!< 0x02000000 */ +#define ADC_SQR2_SQ12_1 (0x02UL << ADC_SQR2_SQ12_Pos) /*!< 0x04000000 */ +#define ADC_SQR2_SQ12_2 (0x04UL << ADC_SQR2_SQ12_Pos) /*!< 0x08000000 */ +#define ADC_SQR2_SQ12_3 (0x08UL << ADC_SQR2_SQ12_Pos) /*!< 0x10000000 */ +#define ADC_SQR2_SQ12_4 (0x10UL << ADC_SQR2_SQ12_Pos) /*!< 0x20000000 */ + +/******************* Bit definition for ADC_SQR3 register *******************/ +#define ADC_SQR3_SQ1_Pos (0U) +#define ADC_SQR3_SQ1_Msk (0x1FUL << ADC_SQR3_SQ1_Pos) /*!< 0x0000001F */ +#define ADC_SQR3_SQ1 ADC_SQR3_SQ1_Msk /*!< ADC group regular sequencer rank 1 */ +#define ADC_SQR3_SQ1_0 (0x01UL << ADC_SQR3_SQ1_Pos) /*!< 0x00000001 */ +#define ADC_SQR3_SQ1_1 (0x02UL << ADC_SQR3_SQ1_Pos) /*!< 0x00000002 */ +#define ADC_SQR3_SQ1_2 (0x04UL << ADC_SQR3_SQ1_Pos) /*!< 0x00000004 */ +#define ADC_SQR3_SQ1_3 (0x08UL << ADC_SQR3_SQ1_Pos) /*!< 0x00000008 */ +#define ADC_SQR3_SQ1_4 (0x10UL << ADC_SQR3_SQ1_Pos) /*!< 0x00000010 */ + +#define ADC_SQR3_SQ2_Pos (5U) +#define ADC_SQR3_SQ2_Msk (0x1FUL << ADC_SQR3_SQ2_Pos) /*!< 0x000003E0 */ +#define ADC_SQR3_SQ2 ADC_SQR3_SQ2_Msk /*!< ADC group regular sequencer rank 2 */ +#define ADC_SQR3_SQ2_0 (0x01UL << ADC_SQR3_SQ2_Pos) /*!< 0x00000020 */ +#define ADC_SQR3_SQ2_1 (0x02UL << ADC_SQR3_SQ2_Pos) /*!< 0x00000040 */ +#define ADC_SQR3_SQ2_2 (0x04UL << ADC_SQR3_SQ2_Pos) /*!< 0x00000080 */ +#define ADC_SQR3_SQ2_3 (0x08UL << ADC_SQR3_SQ2_Pos) /*!< 0x00000100 */ +#define ADC_SQR3_SQ2_4 (0x10UL << ADC_SQR3_SQ2_Pos) /*!< 0x00000200 */ + +#define ADC_SQR3_SQ3_Pos (10U) +#define ADC_SQR3_SQ3_Msk (0x1FUL << ADC_SQR3_SQ3_Pos) /*!< 0x00007C00 */ +#define ADC_SQR3_SQ3 ADC_SQR3_SQ3_Msk /*!< ADC group regular sequencer rank 3 */ +#define ADC_SQR3_SQ3_0 (0x01UL << ADC_SQR3_SQ3_Pos) /*!< 0x00000400 */ +#define ADC_SQR3_SQ3_1 (0x02UL << ADC_SQR3_SQ3_Pos) /*!< 0x00000800 */ +#define ADC_SQR3_SQ3_2 (0x04UL << ADC_SQR3_SQ3_Pos) /*!< 0x00001000 */ +#define ADC_SQR3_SQ3_3 (0x08UL << ADC_SQR3_SQ3_Pos) /*!< 0x00002000 */ +#define ADC_SQR3_SQ3_4 (0x10UL << ADC_SQR3_SQ3_Pos) /*!< 0x00004000 */ + +#define ADC_SQR3_SQ4_Pos (15U) +#define ADC_SQR3_SQ4_Msk (0x1FUL << ADC_SQR3_SQ4_Pos) /*!< 0x000F8000 */ +#define ADC_SQR3_SQ4 ADC_SQR3_SQ4_Msk /*!< ADC group regular sequencer rank 4 */ +#define ADC_SQR3_SQ4_0 (0x01UL << ADC_SQR3_SQ4_Pos) /*!< 0x00008000 */ +#define ADC_SQR3_SQ4_1 (0x02UL << ADC_SQR3_SQ4_Pos) /*!< 0x00010000 */ +#define ADC_SQR3_SQ4_2 (0x04UL << ADC_SQR3_SQ4_Pos) /*!< 0x00020000 */ +#define ADC_SQR3_SQ4_3 (0x08UL << ADC_SQR3_SQ4_Pos) /*!< 0x00040000 */ +#define ADC_SQR3_SQ4_4 (0x10UL << ADC_SQR3_SQ4_Pos) /*!< 0x00080000 */ + +#define ADC_SQR3_SQ5_Pos (20U) +#define ADC_SQR3_SQ5_Msk (0x1FUL << ADC_SQR3_SQ5_Pos) /*!< 0x01F00000 */ +#define ADC_SQR3_SQ5 ADC_SQR3_SQ5_Msk /*!< ADC group regular sequencer rank 5 */ +#define ADC_SQR3_SQ5_0 (0x01UL << ADC_SQR3_SQ5_Pos) /*!< 0x00100000 */ +#define ADC_SQR3_SQ5_1 (0x02UL << ADC_SQR3_SQ5_Pos) /*!< 0x00200000 */ +#define ADC_SQR3_SQ5_2 (0x04UL << ADC_SQR3_SQ5_Pos) /*!< 0x00400000 */ +#define ADC_SQR3_SQ5_3 (0x08UL << ADC_SQR3_SQ5_Pos) /*!< 0x00800000 */ +#define ADC_SQR3_SQ5_4 (0x10UL << ADC_SQR3_SQ5_Pos) /*!< 0x01000000 */ + +#define ADC_SQR3_SQ6_Pos (25U) +#define ADC_SQR3_SQ6_Msk (0x1FUL << ADC_SQR3_SQ6_Pos) /*!< 0x3E000000 */ +#define ADC_SQR3_SQ6 ADC_SQR3_SQ6_Msk /*!< ADC group regular sequencer rank 6 */ +#define ADC_SQR3_SQ6_0 (0x01UL << ADC_SQR3_SQ6_Pos) /*!< 0x02000000 */ +#define ADC_SQR3_SQ6_1 (0x02UL << ADC_SQR3_SQ6_Pos) /*!< 0x04000000 */ +#define ADC_SQR3_SQ6_2 (0x04UL << ADC_SQR3_SQ6_Pos) /*!< 0x08000000 */ +#define ADC_SQR3_SQ6_3 (0x08UL << ADC_SQR3_SQ6_Pos) /*!< 0x10000000 */ +#define ADC_SQR3_SQ6_4 (0x10UL << ADC_SQR3_SQ6_Pos) /*!< 0x20000000 */ + +/******************* Bit definition for ADC_JSQR register *******************/ +#define ADC_JSQR_JSQ1_Pos (0U) +#define ADC_JSQR_JSQ1_Msk (0x1FUL << ADC_JSQR_JSQ1_Pos) /*!< 0x0000001F */ +#define ADC_JSQR_JSQ1 ADC_JSQR_JSQ1_Msk /*!< ADC group injected sequencer rank 1 */ +#define ADC_JSQR_JSQ1_0 (0x01UL << ADC_JSQR_JSQ1_Pos) /*!< 0x00000001 */ +#define ADC_JSQR_JSQ1_1 (0x02UL << ADC_JSQR_JSQ1_Pos) /*!< 0x00000002 */ +#define ADC_JSQR_JSQ1_2 (0x04UL << ADC_JSQR_JSQ1_Pos) /*!< 0x00000004 */ +#define ADC_JSQR_JSQ1_3 (0x08UL << ADC_JSQR_JSQ1_Pos) /*!< 0x00000008 */ +#define ADC_JSQR_JSQ1_4 (0x10UL << ADC_JSQR_JSQ1_Pos) /*!< 0x00000010 */ + +#define ADC_JSQR_JSQ2_Pos (5U) +#define ADC_JSQR_JSQ2_Msk (0x1FUL << ADC_JSQR_JSQ2_Pos) /*!< 0x000003E0 */ +#define ADC_JSQR_JSQ2 ADC_JSQR_JSQ2_Msk /*!< ADC group injected sequencer rank 2 */ +#define ADC_JSQR_JSQ2_0 (0x01UL << ADC_JSQR_JSQ2_Pos) /*!< 0x00000020 */ +#define ADC_JSQR_JSQ2_1 (0x02UL << ADC_JSQR_JSQ2_Pos) /*!< 0x00000040 */ +#define ADC_JSQR_JSQ2_2 (0x04UL << ADC_JSQR_JSQ2_Pos) /*!< 0x00000080 */ +#define ADC_JSQR_JSQ2_3 (0x08UL << ADC_JSQR_JSQ2_Pos) /*!< 0x00000100 */ +#define ADC_JSQR_JSQ2_4 (0x10UL << ADC_JSQR_JSQ2_Pos) /*!< 0x00000200 */ + +#define ADC_JSQR_JSQ3_Pos (10U) +#define ADC_JSQR_JSQ3_Msk (0x1FUL << ADC_JSQR_JSQ3_Pos) /*!< 0x00007C00 */ +#define ADC_JSQR_JSQ3 ADC_JSQR_JSQ3_Msk /*!< ADC group injected sequencer rank 3 */ +#define ADC_JSQR_JSQ3_0 (0x01UL << ADC_JSQR_JSQ3_Pos) /*!< 0x00000400 */ +#define ADC_JSQR_JSQ3_1 (0x02UL << ADC_JSQR_JSQ3_Pos) /*!< 0x00000800 */ +#define ADC_JSQR_JSQ3_2 (0x04UL << ADC_JSQR_JSQ3_Pos) /*!< 0x00001000 */ +#define ADC_JSQR_JSQ3_3 (0x08UL << ADC_JSQR_JSQ3_Pos) /*!< 0x00002000 */ +#define ADC_JSQR_JSQ3_4 (0x10UL << ADC_JSQR_JSQ3_Pos) /*!< 0x00004000 */ + +#define ADC_JSQR_JSQ4_Pos (15U) +#define ADC_JSQR_JSQ4_Msk (0x1FUL << ADC_JSQR_JSQ4_Pos) /*!< 0x000F8000 */ +#define ADC_JSQR_JSQ4 ADC_JSQR_JSQ4_Msk /*!< ADC group injected sequencer rank 4 */ +#define ADC_JSQR_JSQ4_0 (0x01UL << ADC_JSQR_JSQ4_Pos) /*!< 0x00008000 */ +#define ADC_JSQR_JSQ4_1 (0x02UL << ADC_JSQR_JSQ4_Pos) /*!< 0x00010000 */ +#define ADC_JSQR_JSQ4_2 (0x04UL << ADC_JSQR_JSQ4_Pos) /*!< 0x00020000 */ +#define ADC_JSQR_JSQ4_3 (0x08UL << ADC_JSQR_JSQ4_Pos) /*!< 0x00040000 */ +#define ADC_JSQR_JSQ4_4 (0x10UL << ADC_JSQR_JSQ4_Pos) /*!< 0x00080000 */ + +#define ADC_JSQR_JL_Pos (20U) +#define ADC_JSQR_JL_Msk (0x3UL << ADC_JSQR_JL_Pos) /*!< 0x00300000 */ +#define ADC_JSQR_JL ADC_JSQR_JL_Msk /*!< ADC group injected sequencer scan length */ +#define ADC_JSQR_JL_0 (0x1UL << ADC_JSQR_JL_Pos) /*!< 0x00100000 */ +#define ADC_JSQR_JL_1 (0x2UL << ADC_JSQR_JL_Pos) /*!< 0x00200000 */ + +/******************* Bit definition for ADC_JDR1 register *******************/ +#define ADC_JDR1_JDATA_Pos (0U) +#define ADC_JDR1_JDATA_Msk (0xFFFFUL << ADC_JDR1_JDATA_Pos) /*!< 0x0000FFFF */ +#define ADC_JDR1_JDATA ADC_JDR1_JDATA_Msk /*!< ADC group injected sequencer rank 1 conversion data */ + +/******************* Bit definition for ADC_JDR2 register *******************/ +#define ADC_JDR2_JDATA_Pos (0U) +#define ADC_JDR2_JDATA_Msk (0xFFFFUL << ADC_JDR2_JDATA_Pos) /*!< 0x0000FFFF */ +#define ADC_JDR2_JDATA ADC_JDR2_JDATA_Msk /*!< ADC group injected sequencer rank 2 conversion data */ + +/******************* Bit definition for ADC_JDR3 register *******************/ +#define ADC_JDR3_JDATA_Pos (0U) +#define ADC_JDR3_JDATA_Msk (0xFFFFUL << ADC_JDR3_JDATA_Pos) /*!< 0x0000FFFF */ +#define ADC_JDR3_JDATA ADC_JDR3_JDATA_Msk /*!< ADC group injected sequencer rank 3 conversion data */ + +/******************* Bit definition for ADC_JDR4 register *******************/ +#define ADC_JDR4_JDATA_Pos (0U) +#define ADC_JDR4_JDATA_Msk (0xFFFFUL << ADC_JDR4_JDATA_Pos) /*!< 0x0000FFFF */ +#define ADC_JDR4_JDATA ADC_JDR4_JDATA_Msk /*!< ADC group injected sequencer rank 4 conversion data */ + +/******************** Bit definition for ADC_DR register ********************/ +#define ADC_DR_DATA_Pos (0U) +#define ADC_DR_DATA_Msk (0xFFFFUL << ADC_DR_DATA_Pos) /*!< 0x0000FFFF */ +#define ADC_DR_DATA ADC_DR_DATA_Msk /*!< ADC group regular conversion data */ +#define ADC_DR_ADC2DATA_Pos (16U) +#define ADC_DR_ADC2DATA_Msk (0xFFFFUL << ADC_DR_ADC2DATA_Pos) /*!< 0xFFFF0000 */ +#define ADC_DR_ADC2DATA ADC_DR_ADC2DATA_Msk /*!< ADC group regular conversion data for ADC slave, in multimode */ + + +/*****************************************************************************/ +/* */ +/* Timers (TIM) */ +/* */ +/*****************************************************************************/ +/******************* Bit definition for TIM_CR1 register *******************/ +#define TIM_CR1_CEN_Pos (0U) +#define TIM_CR1_CEN_Msk (0x1UL << TIM_CR1_CEN_Pos) /*!< 0x00000001 */ +#define TIM_CR1_CEN TIM_CR1_CEN_Msk /*!
© Copyright (c) 2017 STMicroelectronics. + * All rights reserved.
+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/** @addtogroup CMSIS + * @{ + */ + +/** @addtogroup stm32f1xx + * @{ + */ + +#ifndef __STM32F1XX_H +#define __STM32F1XX_H + +#ifdef __cplusplus +extern "C" { +#endif /* __cplusplus */ + +/** @addtogroup Library_configuration_section + * @{ + */ + +/** + * @brief STM32 Family + */ +#if !defined (STM32F1) +#define STM32F1 +#endif /* STM32F1 */ + +/* Uncomment the line below according to the target STM32L device used in your + application + */ + +#if !defined (STM32F100xB) && !defined (STM32F100xE) && !defined (STM32F101x6) && \ + !defined (STM32F101xB) && !defined (STM32F101xE) && !defined (STM32F101xG) && !defined (STM32F102x6) && !defined (STM32F102xB) && !defined (STM32F103x6) && \ + !defined (STM32F103xB) && !defined (STM32F103xE) && !defined (STM32F103xG) && !defined (STM32F105xC) && !defined (STM32F107xC) +/* #define STM32F100xB */ /*!< STM32F100C4, STM32F100R4, STM32F100C6, STM32F100R6, STM32F100C8, STM32F100R8, STM32F100V8, STM32F100CB, STM32F100RB and STM32F100VB */ +/* #define STM32F100xE */ /*!< STM32F100RC, STM32F100VC, STM32F100ZC, STM32F100RD, STM32F100VD, STM32F100ZD, STM32F100RE, STM32F100VE and STM32F100ZE */ +/* #define STM32F101x6 */ /*!< STM32F101C4, STM32F101R4, STM32F101T4, STM32F101C6, STM32F101R6 and STM32F101T6 Devices */ +/* #define STM32F101xB */ /*!< STM32F101C8, STM32F101R8, STM32F101T8, STM32F101V8, STM32F101CB, STM32F101RB, STM32F101TB and STM32F101VB */ +/* #define STM32F101xE */ /*!< STM32F101RC, STM32F101VC, STM32F101ZC, STM32F101RD, STM32F101VD, STM32F101ZD, STM32F101RE, STM32F101VE and STM32F101ZE */ +/* #define STM32F101xG */ /*!< STM32F101RF, STM32F101VF, STM32F101ZF, STM32F101RG, STM32F101VG and STM32F101ZG */ +/* #define STM32F102x6 */ /*!< STM32F102C4, STM32F102R4, STM32F102C6 and STM32F102R6 */ +/* #define STM32F102xB */ /*!< STM32F102C8, STM32F102R8, STM32F102CB and STM32F102RB */ +/* #define STM32F103x6 */ /*!< STM32F103C4, STM32F103R4, STM32F103T4, STM32F103C6, STM32F103R6 and STM32F103T6 */ +/* #define STM32F103xB */ /*!< STM32F103C8, STM32F103R8, STM32F103T8, STM32F103V8, STM32F103CB, STM32F103RB, STM32F103TB and STM32F103VB */ +/* #define STM32F103xE */ /*!< STM32F103RC, STM32F103VC, STM32F103ZC, STM32F103RD, STM32F103VD, STM32F103ZD, STM32F103RE, STM32F103VE and STM32F103ZE */ +/* #define STM32F103xG */ /*!< STM32F103RF, STM32F103VF, STM32F103ZF, STM32F103RG, STM32F103VG and STM32F103ZG */ +/* #define STM32F105xC */ /*!< STM32F105R8, STM32F105V8, STM32F105RB, STM32F105VB, STM32F105RC and STM32F105VC */ +/* #define STM32F107xC */ /*!< STM32F107RB, STM32F107VB, STM32F107RC and STM32F107VC */ +#endif + +/* Tip: To avoid modifying this file each time you need to switch between these + devices, you can define the device in your toolchain compiler preprocessor. + */ + +#if !defined (USE_HAL_DRIVER) +/** + * @brief Comment the line below if you will not use the peripherals drivers. + In this case, these drivers will not be included and the application code will + be based on direct access to peripherals registers + */ +/*#define USE_HAL_DRIVER */ +#endif /* USE_HAL_DRIVER */ + +/** + * @brief CMSIS Device version number V4.3.1 + */ +#define __STM32F1_CMSIS_VERSION_MAIN (0x04) /*!< [31:24] main version */ +#define __STM32F1_CMSIS_VERSION_SUB1 (0x03) /*!< [23:16] sub1 version */ +#define __STM32F1_CMSIS_VERSION_SUB2 (0x01) /*!< [15:8] sub2 version */ +#define __STM32F1_CMSIS_VERSION_RC (0x00) /*!< [7:0] release candidate */ +#define __STM32F1_CMSIS_VERSION ((__STM32F1_CMSIS_VERSION_MAIN << 24)\ + |(__STM32F1_CMSIS_VERSION_SUB1 << 16)\ + |(__STM32F1_CMSIS_VERSION_SUB2 << 8 )\ + |(__STM32F1_CMSIS_VERSION_RC)) + +/** + * @} + */ + +/** @addtogroup Device_Included + * @{ + */ + +#if defined(STM32F100xB) +#include "stm32f100xb.h" +#elif defined(STM32F100xE) +#include "stm32f100xe.h" +#elif defined(STM32F101x6) +#include "stm32f101x6.h" +#elif defined(STM32F101xB) +#include "stm32f101xb.h" +#elif defined(STM32F101xE) +#include "stm32f101xe.h" +#elif defined(STM32F101xG) +#include "stm32f101xg.h" +#elif defined(STM32F102x6) +#include "stm32f102x6.h" +#elif defined(STM32F102xB) +#include "stm32f102xb.h" +#elif defined(STM32F103x6) +#include "stm32f103x6.h" +#elif defined(STM32F103xB) +#include "stm32f103xb.h" +#elif defined(STM32F103xE) +#include "stm32f103xe.h" +#elif defined(STM32F103xG) +#include "stm32f103xg.h" +#elif defined(STM32F105xC) +#include "stm32f105xc.h" +#elif defined(STM32F107xC) +#include "stm32f107xc.h" +#else +#error "Please select first the target STM32F1xx device used in your application (in stm32f1xx.h file)" +#endif + +/** + * @} + */ + +/** @addtogroup Exported_types + * @{ + */ +typedef enum +{ + RESET = 0, + SET = !RESET +} FlagStatus, ITStatus; + +typedef enum +{ + DISABLE = 0, + ENABLE = !DISABLE +} FunctionalState; +#define IS_FUNCTIONAL_STATE(STATE) (((STATE) == DISABLE) || ((STATE) == ENABLE)) + +typedef enum +{ + SUCCESS = 0U, + ERROR = !SUCCESS +} ErrorStatus; + +/** + * @} + */ + + +/** @addtogroup Exported_macros + * @{ + */ +#define SET_BIT(REG, BIT) ((REG) |= (BIT)) + +#define CLEAR_BIT(REG, BIT) ((REG) &= ~(BIT)) + +#define READ_BIT(REG, BIT) ((REG) & (BIT)) + +#define CLEAR_REG(REG) ((REG) = (0x0)) + +#define WRITE_REG(REG, VAL) ((REG) = (VAL)) + +#define READ_REG(REG) ((REG)) + +#define MODIFY_REG(REG, CLEARMASK, SETMASK) WRITE_REG((REG), (((READ_REG(REG)) & (~(CLEARMASK))) | (SETMASK))) + +#define POSITION_VAL(VAL) (__CLZ(__RBIT(VAL))) + + +/** + * @} + */ + +#if defined (USE_HAL_DRIVER) +#include "stm32f1xx_hal.h" +#endif /* USE_HAL_DRIVER */ + + +#ifdef __cplusplus +} +#endif /* __cplusplus */ + +#endif /* __STM32F1xx_H */ +/** + * @} + */ + +/** + * @} + */ + + + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F1xx/Include/system_stm32f1xx.h b/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F1xx/Include/system_stm32f1xx.h new file mode 100644 index 00000000..46f1691b --- /dev/null +++ b/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F1xx/Include/system_stm32f1xx.h @@ -0,0 +1,98 @@ +/** + ****************************************************************************** + * @file system_stm32f10x.h + * @author MCD Application Team + * @brief CMSIS Cortex-M3 Device Peripheral Access Layer System Header File. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2017 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/** @addtogroup CMSIS + * @{ + */ + +/** @addtogroup stm32f10x_system + * @{ + */ + +/** + * @brief Define to prevent recursive inclusion + */ +#ifndef __SYSTEM_STM32F10X_H +#define __SYSTEM_STM32F10X_H + +#ifdef __cplusplus +extern "C" { +#endif + +/** @addtogroup STM32F10x_System_Includes + * @{ + */ + +/** + * @} + */ + + +/** @addtogroup STM32F10x_System_Exported_types + * @{ + */ + +extern uint32_t SystemCoreClock; /*!< System Clock Frequency (Core Clock) */ +extern const uint8_t AHBPrescTable[16U]; /*!< AHB prescalers table values */ +extern const uint8_t APBPrescTable[8U]; /*!< APB prescalers table values */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Exported_Constants + * @{ + */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Exported_Macros + * @{ + */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Exported_Functions + * @{ + */ + +extern void SystemInit(void); +extern void SystemCoreClockUpdate(void); +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /*__SYSTEM_STM32F10X_H */ + +/** + * @} + */ + +/** + * @} + */ +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F4xx/Include/stm32f401xc.h b/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F4xx/Include/stm32f401xc.h deleted file mode 100644 index 688c60cc..00000000 --- a/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F4xx/Include/stm32f401xc.h +++ /dev/null @@ -1,4805 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f401xc.h - * @author MCD Application Team - * @version V2.5.0 - * @date 22-April-2016 - * @brief CMSIS STM32F401xCxx Device Peripheral Access Layer Header File. - * - * This file contains: - * - Data structures and the address mapping for all peripherals - * - peripherals registers declarations and bits definition - * - Macros to access peripherals registers hardware - * - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f401xc - * @{ - */ - -#ifndef __STM32F401xC_H -#define __STM32F401xC_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1, ADC2 and ADC3 global Interrupts */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - SPI4_IRQn = 84 /*!< SPI4 global Interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - uint32_t RESERVED7[1]; /*!< Reserved, 0x88 */ - __IO uint32_t DCKCFGR; /*!< RCC DCKCFGR configuration register, Address offset: 0x8C */ -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - -/** - * @brief __USB_OTG_Core_register - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register Address offset : 0x00 */ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register Address offset : 0x04 */ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register Address offset : 0x08 */ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register Address offset : 0x0C */ - __IO uint32_t GRSTCTL; /*!< Core Reset Register Address offset : 0x10 */ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register Address offset : 0x14 */ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register Address offset : 0x18 */ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register Address offset : 0x1C */ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register Address offset : 0x20 */ - __IO uint32_t GRXFSIZ; /* Receive FIFO Size Register Address offset : 0x24 */ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register Address offset : 0x28 */ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg Address offset : 0x2C */ - uint32_t Reserved30[2]; /* Reserved Address offset : 0x30 */ - __IO uint32_t GCCFG; /*!< General Purpose IO Register Address offset : 0x38 */ - __IO uint32_t CID; /*!< User ID Register Address offset : 0x3C */ - uint32_t Reserved40[48]; /*!< Reserved Address offset : 0x40-0xFF */ - __IO uint32_t HPTXFSIZ; /*!< Host Periodic Tx FIFO Size Reg Address offset : 0x100 */ - __IO uint32_t DIEPTXF[0x0F]; /*!< dev Periodic Transmit FIFO */ -} -USB_OTG_GlobalTypeDef; - - - -/** - * @brief __device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /*!< dev Configuration Register Address offset : 0x800 */ - __IO uint32_t DCTL; /*!< dev Control Register Address offset : 0x804 */ - __IO uint32_t DSTS; /*!< dev Status Register (RO) Address offset : 0x808 */ - uint32_t Reserved0C; /*!< Reserved Address offset : 0x80C */ - __IO uint32_t DIEPMSK; /* !< dev IN Endpoint Mask Address offset : 0x810 */ - __IO uint32_t DOEPMSK; /*!< dev OUT Endpoint Mask Address offset : 0x814 */ - __IO uint32_t DAINT; /*!< dev All Endpoints Itr Reg Address offset : 0x818 */ - __IO uint32_t DAINTMSK; /*!< dev All Endpoints Itr Mask Address offset : 0x81C */ - uint32_t Reserved20; /*!< Reserved Address offset : 0x820 */ - uint32_t Reserved9; /*!< Reserved Address offset : 0x824 */ - __IO uint32_t DVBUSDIS; /*!< dev VBUS discharge Register Address offset : 0x828 */ - __IO uint32_t DVBUSPULSE; /*!< dev VBUS Pulse Register Address offset : 0x82C */ - __IO uint32_t DTHRCTL; /*!< dev thr Address offset : 0x830 */ - __IO uint32_t DIEPEMPMSK; /*!< dev empty msk Address offset : 0x834 */ - __IO uint32_t DEACHINT; /*!< dedicated EP interrupt Address offset : 0x838 */ - __IO uint32_t DEACHMSK; /*!< dedicated EP msk Address offset : 0x83C */ - uint32_t Reserved40; /*!< dedicated EP mask Address offset : 0x840 */ - __IO uint32_t DINEP1MSK; /*!< dedicated EP mask Address offset : 0x844 */ - uint32_t Reserved44[15]; /*!< Reserved Address offset : 0x844-0x87C */ - __IO uint32_t DOUTEP1MSK; /*!< dedicated EP msk Address offset : 0x884 */ -} -USB_OTG_DeviceTypeDef; - - -/** - * @brief __IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /* dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /* Reserved 900h + (ep_num * 20h) + 04h */ - __IO uint32_t DIEPINT; /* dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /* Reserved 900h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DIEPTSIZ; /* IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h */ - __IO uint32_t DIEPDMA; /* IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h */ - __IO uint32_t DTXFSTS; /*IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h */ - uint32_t Reserved18; /* Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch */ -} -USB_OTG_INEndpointTypeDef; - - -/** - * @brief __OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /* dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved B00h + (ep_num * 20h) + 04h*/ - __IO uint32_t DOEPINT; /* dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved B00h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DOEPTSIZ; /* dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h*/ - __IO uint32_t DOEPDMA; /* dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h*/ - uint32_t Reserved18[2]; /* Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch*/ -} -USB_OTG_OUTEndpointTypeDef; - - -/** - * @brief __Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /* Host Configuration Register 400h*/ - __IO uint32_t HFIR; /* Host Frame Interval Register 404h*/ - __IO uint32_t HFNUM; /* Host Frame Nbr/Frame Remaining 408h*/ - uint32_t Reserved40C; /* Reserved 40Ch*/ - __IO uint32_t HPTXSTS; /* Host Periodic Tx FIFO/ Queue Status 410h*/ - __IO uint32_t HAINT; /* Host All Channels Interrupt Register 414h*/ - __IO uint32_t HAINTMSK; /* Host All Channels Interrupt Mask 418h*/ -} -USB_OTG_HostTypeDef; - - -/** - * @brief __Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; - __IO uint32_t HCSPLT; - __IO uint32_t HCINT; - __IO uint32_t HCINTMSK; - __IO uint32_t HCTSIZ; - __IO uint32_t HCDMA; - uint32_t Reserved[2]; -} -USB_OTG_HostChannelTypeDef; - - -/** - * @brief Peripheral_memory_map - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(64 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define BKPSRAM_BASE 0x40024000U /*!< Backup SRAM(4 KB) base address in the alias region */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(64 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define BKPSRAM_BB_BASE 0x42480000U /*!< Backup SRAM(4 KB) base address in the bit-band region */ -#define FLASH_END 0x0803FFFFU /*!< FLASH end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SPI4_BASE (APB2PERIPH_BASE + 0x3400U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SPI4 ((SPI_TypeDef *) SPI4_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f401xe - * @{ - */ - -#ifndef __STM32F401xE_H -#define __STM32F401xE_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1, ADC2 and ADC3 global Interrupts */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - SPI4_IRQn = 84 /*!< SPI4 global Interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - uint32_t RESERVED7[1]; /*!< Reserved, 0x88 */ - __IO uint32_t DCKCFGR; /*!< RCC DCKCFGR configuration register, Address offset: 0x8C */ -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - -/** - * @brief __USB_OTG_Core_register - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register Address offset : 0x00 */ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register Address offset : 0x04 */ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register Address offset : 0x08 */ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register Address offset : 0x0C */ - __IO uint32_t GRSTCTL; /*!< Core Reset Register Address offset : 0x10 */ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register Address offset : 0x14 */ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register Address offset : 0x18 */ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register Address offset : 0x1C */ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register Address offset : 0x20 */ - __IO uint32_t GRXFSIZ; /* Receive FIFO Size Register Address offset : 0x24 */ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register Address offset : 0x28 */ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg Address offset : 0x2C */ - uint32_t Reserved30[2]; /* Reserved Address offset : 0x30 */ - __IO uint32_t GCCFG; /*!< General Purpose IO Register Address offset : 0x38 */ - __IO uint32_t CID; /*!< User ID Register Address offset : 0x3C */ - uint32_t Reserved40[48]; /*!< Reserved Address offset : 0x40-0xFF */ - __IO uint32_t HPTXFSIZ; /*!< Host Periodic Tx FIFO Size Reg Address offset : 0x100 */ - __IO uint32_t DIEPTXF[0x0F]; /*!< dev Periodic Transmit FIFO */ -} -USB_OTG_GlobalTypeDef; - - - -/** - * @brief __device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /*!< dev Configuration Register Address offset : 0x800 */ - __IO uint32_t DCTL; /*!< dev Control Register Address offset : 0x804 */ - __IO uint32_t DSTS; /*!< dev Status Register (RO) Address offset : 0x808 */ - uint32_t Reserved0C; /*!< Reserved Address offset : 0x80C */ - __IO uint32_t DIEPMSK; /* !< dev IN Endpoint Mask Address offset : 0x810 */ - __IO uint32_t DOEPMSK; /*!< dev OUT Endpoint Mask Address offset : 0x814 */ - __IO uint32_t DAINT; /*!< dev All Endpoints Itr Reg Address offset : 0x818 */ - __IO uint32_t DAINTMSK; /*!< dev All Endpoints Itr Mask Address offset : 0x81C */ - uint32_t Reserved20; /*!< Reserved Address offset : 0x820 */ - uint32_t Reserved9; /*!< Reserved Address offset : 0x824 */ - __IO uint32_t DVBUSDIS; /*!< dev VBUS discharge Register Address offset : 0x828 */ - __IO uint32_t DVBUSPULSE; /*!< dev VBUS Pulse Register Address offset : 0x82C */ - __IO uint32_t DTHRCTL; /*!< dev thr Address offset : 0x830 */ - __IO uint32_t DIEPEMPMSK; /*!< dev empty msk Address offset : 0x834 */ - __IO uint32_t DEACHINT; /*!< dedicated EP interrupt Address offset : 0x838 */ - __IO uint32_t DEACHMSK; /*!< dedicated EP msk Address offset : 0x83C */ - uint32_t Reserved40; /*!< dedicated EP mask Address offset : 0x840 */ - __IO uint32_t DINEP1MSK; /*!< dedicated EP mask Address offset : 0x844 */ - uint32_t Reserved44[15]; /*!< Reserved Address offset : 0x844-0x87C */ - __IO uint32_t DOUTEP1MSK; /*!< dedicated EP msk Address offset : 0x884 */ -} -USB_OTG_DeviceTypeDef; - - -/** - * @brief __IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /* dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /* Reserved 900h + (ep_num * 20h) + 04h */ - __IO uint32_t DIEPINT; /* dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /* Reserved 900h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DIEPTSIZ; /* IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h */ - __IO uint32_t DIEPDMA; /* IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h */ - __IO uint32_t DTXFSTS; /*IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h */ - uint32_t Reserved18; /* Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch */ -} -USB_OTG_INEndpointTypeDef; - - -/** - * @brief __OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /* dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved B00h + (ep_num * 20h) + 04h*/ - __IO uint32_t DOEPINT; /* dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved B00h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DOEPTSIZ; /* dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h*/ - __IO uint32_t DOEPDMA; /* dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h*/ - uint32_t Reserved18[2]; /* Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch*/ -} -USB_OTG_OUTEndpointTypeDef; - - -/** - * @brief __Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /* Host Configuration Register 400h*/ - __IO uint32_t HFIR; /* Host Frame Interval Register 404h*/ - __IO uint32_t HFNUM; /* Host Frame Nbr/Frame Remaining 408h*/ - uint32_t Reserved40C; /* Reserved 40Ch*/ - __IO uint32_t HPTXSTS; /* Host Periodic Tx FIFO/ Queue Status 410h*/ - __IO uint32_t HAINT; /* Host All Channels Interrupt Register 414h*/ - __IO uint32_t HAINTMSK; /* Host All Channels Interrupt Mask 418h*/ -} -USB_OTG_HostTypeDef; - - -/** - * @brief __Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; - __IO uint32_t HCSPLT; - __IO uint32_t HCINT; - __IO uint32_t HCINTMSK; - __IO uint32_t HCTSIZ; - __IO uint32_t HCDMA; - uint32_t Reserved[2]; -} -USB_OTG_HostChannelTypeDef; - -/** - * @brief Peripheral_memory_map - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(96 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define BKPSRAM_BASE 0x40024000U /*!< Backup SRAM(4 KB) base address in the alias region */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(96 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define BKPSRAM_BB_BASE 0x42480000U /*!< Backup SRAM(4 KB) base address in the bit-band region */ -#define FLASH_END 0x0807FFFFU /*!< FLASH end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SPI4_BASE (APB2PERIPH_BASE + 0x3400U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SPI4 ((SPI_TypeDef *) SPI4_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f405xx - * @{ - */ - -#ifndef __STM32F405xx_H -#define __STM32F405xx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1, ADC2 and ADC3 global Interrupts */ - CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */ - CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */ - CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ - CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - USART3_IRQn = 39, /*!< USART3 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */ - TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */ - TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */ - TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare Interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - FSMC_IRQn = 48, /*!< FSMC global Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - UART4_IRQn = 52, /*!< UART4 global Interrupt */ - UART5_IRQn = 53, /*!< UART5 global Interrupt */ - TIM6_DAC_IRQn = 54, /*!< TIM6 global and DAC1&2 underrun error interrupts */ - TIM7_IRQn = 55, /*!< TIM7 global interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */ - CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */ - CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */ - CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - OTG_HS_EP1_OUT_IRQn = 74, /*!< USB OTG HS End Point 1 Out global interrupt */ - OTG_HS_EP1_IN_IRQn = 75, /*!< USB OTG HS End Point 1 In global interrupt */ - OTG_HS_WKUP_IRQn = 76, /*!< USB OTG HS Wakeup through EXTI interrupt */ - OTG_HS_IRQn = 77, /*!< USB OTG HS global interrupt */ - HASH_RNG_IRQn = 80, /*!< Hash and RNG global interrupt */ - FPU_IRQn = 81 /*!< FPU global interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - - -/** - * @brief Controller Area Network TxMailBox - */ - -typedef struct -{ - __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ - __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ - __IO uint32_t TDLR; /*!< CAN mailbox data low register */ - __IO uint32_t TDHR; /*!< CAN mailbox data high register */ -} CAN_TxMailBox_TypeDef; - -/** - * @brief Controller Area Network FIFOMailBox - */ - -typedef struct -{ - __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ - __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ - __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ - __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ -} CAN_FIFOMailBox_TypeDef; - -/** - * @brief Controller Area Network FilterRegister - */ - -typedef struct -{ - __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ - __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ -} CAN_FilterRegister_TypeDef; - -/** - * @brief Controller Area Network - */ - -typedef struct -{ - __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ - __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ - __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ - __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ - __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ - __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ - __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ - __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ - uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ - CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ - CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ - uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ - __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ - __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ - uint32_t RESERVED2; /*!< Reserved, 0x208 */ - __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ - uint32_t RESERVED3; /*!< Reserved, 0x210 */ - __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ - uint32_t RESERVED4; /*!< Reserved, 0x218 */ - __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ - uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ - CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ -} CAN_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Digital to Analog Converter - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ - __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ - __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ - __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ - __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ - __IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */ - __IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */ - __IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */ - __IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */ - __IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */ - __IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */ - __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ - __IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */ - __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ -} DAC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - - -/** - * @brief Flexible Static Memory Controller - */ - -typedef struct -{ - __IO uint32_t BTCR[8]; /*!< NOR/PSRAM chip-select control register(BCR) and chip-select timing register(BTR), Address offset: 0x00-1C */ -} FSMC_Bank1_TypeDef; - -/** - * @brief Flexible Static Memory Controller Bank1E - */ - -typedef struct -{ - __IO uint32_t BWTR[7]; /*!< NOR/PSRAM write timing registers, Address offset: 0x104-0x11C */ -} FSMC_Bank1E_TypeDef; - -/** - * @brief Flexible Static Memory Controller Bank2 - */ - -typedef struct -{ - __IO uint32_t PCR2; /*!< NAND Flash control register 2, Address offset: 0x60 */ - __IO uint32_t SR2; /*!< NAND Flash FIFO status and interrupt register 2, Address offset: 0x64 */ - __IO uint32_t PMEM2; /*!< NAND Flash Common memory space timing register 2, Address offset: 0x68 */ - __IO uint32_t PATT2; /*!< NAND Flash Attribute memory space timing register 2, Address offset: 0x6C */ - uint32_t RESERVED0; /*!< Reserved, 0x70 */ - __IO uint32_t ECCR2; /*!< NAND Flash ECC result registers 2, Address offset: 0x74 */ - uint32_t RESERVED1; /*!< Reserved, 0x78 */ - uint32_t RESERVED2; /*!< Reserved, 0x7C */ - __IO uint32_t PCR3; /*!< NAND Flash control register 3, Address offset: 0x80 */ - __IO uint32_t SR3; /*!< NAND Flash FIFO status and interrupt register 3, Address offset: 0x84 */ - __IO uint32_t PMEM3; /*!< NAND Flash Common memory space timing register 3, Address offset: 0x88 */ - __IO uint32_t PATT3; /*!< NAND Flash Attribute memory space timing register 3, Address offset: 0x8C */ - uint32_t RESERVED3; /*!< Reserved, 0x90 */ - __IO uint32_t ECCR3; /*!< NAND Flash ECC result registers 3, Address offset: 0x94 */ -} FSMC_Bank2_3_TypeDef; - -/** - * @brief Flexible Static Memory Controller Bank4 - */ - -typedef struct -{ - __IO uint32_t PCR4; /*!< PC Card control register 4, Address offset: 0xA0 */ - __IO uint32_t SR4; /*!< PC Card FIFO status and interrupt register 4, Address offset: 0xA4 */ - __IO uint32_t PMEM4; /*!< PC Card Common memory space timing register 4, Address offset: 0xA8 */ - __IO uint32_t PATT4; /*!< PC Card Attribute memory space timing register 4, Address offset: 0xAC */ - __IO uint32_t PIO4; /*!< PC Card I/O space timing register 4, Address offset: 0xB0 */ -} FSMC_Bank4_TypeDef; - - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - - -/** - * @brief __USB_OTG_Core_register - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register Address offset : 0x00 */ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register Address offset : 0x04 */ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register Address offset : 0x08 */ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register Address offset : 0x0C */ - __IO uint32_t GRSTCTL; /*!< Core Reset Register Address offset : 0x10 */ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register Address offset : 0x14 */ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register Address offset : 0x18 */ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register Address offset : 0x1C */ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register Address offset : 0x20 */ - __IO uint32_t GRXFSIZ; /* Receive FIFO Size Register Address offset : 0x24 */ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register Address offset : 0x28 */ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg Address offset : 0x2C */ - uint32_t Reserved30[2]; /* Reserved Address offset : 0x30 */ - __IO uint32_t GCCFG; /*!< General Purpose IO Register Address offset : 0x38 */ - __IO uint32_t CID; /*!< User ID Register Address offset : 0x3C */ - uint32_t Reserved40[48]; /*!< Reserved Address offset : 0x40-0xFF */ - __IO uint32_t HPTXFSIZ; /*!< Host Periodic Tx FIFO Size Reg Address offset : 0x100 */ - __IO uint32_t DIEPTXF[0x0F]; /*!< dev Periodic Transmit FIFO */ -} -USB_OTG_GlobalTypeDef; - - - -/** - * @brief __device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /*!< dev Configuration Register Address offset : 0x800 */ - __IO uint32_t DCTL; /*!< dev Control Register Address offset : 0x804 */ - __IO uint32_t DSTS; /*!< dev Status Register (RO) Address offset : 0x808 */ - uint32_t Reserved0C; /*!< Reserved Address offset : 0x80C */ - __IO uint32_t DIEPMSK; /* !< dev IN Endpoint Mask Address offset : 0x810 */ - __IO uint32_t DOEPMSK; /*!< dev OUT Endpoint Mask Address offset : 0x814 */ - __IO uint32_t DAINT; /*!< dev All Endpoints Itr Reg Address offset : 0x818 */ - __IO uint32_t DAINTMSK; /*!< dev All Endpoints Itr Mask Address offset : 0x81C */ - uint32_t Reserved20; /*!< Reserved Address offset : 0x820 */ - uint32_t Reserved9; /*!< Reserved Address offset : 0x824 */ - __IO uint32_t DVBUSDIS; /*!< dev VBUS discharge Register Address offset : 0x828 */ - __IO uint32_t DVBUSPULSE; /*!< dev VBUS Pulse Register Address offset : 0x82C */ - __IO uint32_t DTHRCTL; /*!< dev thr Address offset : 0x830 */ - __IO uint32_t DIEPEMPMSK; /*!< dev empty msk Address offset : 0x834 */ - __IO uint32_t DEACHINT; /*!< dedicated EP interrupt Address offset : 0x838 */ - __IO uint32_t DEACHMSK; /*!< dedicated EP msk Address offset : 0x83C */ - uint32_t Reserved40; /*!< dedicated EP mask Address offset : 0x840 */ - __IO uint32_t DINEP1MSK; /*!< dedicated EP mask Address offset : 0x844 */ - uint32_t Reserved44[15]; /*!< Reserved Address offset : 0x844-0x87C */ - __IO uint32_t DOUTEP1MSK; /*!< dedicated EP msk Address offset : 0x884 */ -} -USB_OTG_DeviceTypeDef; - - -/** - * @brief __IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /* dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /* Reserved 900h + (ep_num * 20h) + 04h */ - __IO uint32_t DIEPINT; /* dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /* Reserved 900h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DIEPTSIZ; /* IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h */ - __IO uint32_t DIEPDMA; /* IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h */ - __IO uint32_t DTXFSTS; /*IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h */ - uint32_t Reserved18; /* Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch */ -} -USB_OTG_INEndpointTypeDef; - - -/** - * @brief __OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /* dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved B00h + (ep_num * 20h) + 04h*/ - __IO uint32_t DOEPINT; /* dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved B00h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DOEPTSIZ; /* dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h*/ - __IO uint32_t DOEPDMA; /* dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h*/ - uint32_t Reserved18[2]; /* Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch*/ -} -USB_OTG_OUTEndpointTypeDef; - - -/** - * @brief __Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /* Host Configuration Register 400h*/ - __IO uint32_t HFIR; /* Host Frame Interval Register 404h*/ - __IO uint32_t HFNUM; /* Host Frame Nbr/Frame Remaining 408h*/ - uint32_t Reserved40C; /* Reserved 40Ch*/ - __IO uint32_t HPTXSTS; /* Host Periodic Tx FIFO/ Queue Status 410h*/ - __IO uint32_t HAINT; /* Host All Channels Interrupt Register 414h*/ - __IO uint32_t HAINTMSK; /* Host All Channels Interrupt Mask 418h*/ -} -USB_OTG_HostTypeDef; - - -/** - * @brief __Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; - __IO uint32_t HCSPLT; - __IO uint32_t HCINT; - __IO uint32_t HCINTMSK; - __IO uint32_t HCTSIZ; - __IO uint32_t HCDMA; - uint32_t Reserved[2]; -} -USB_OTG_HostChannelTypeDef; - - -/** - * @brief Peripheral_memory_map - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define CCMDATARAM_BASE 0x10000000U /*!< CCM(core coupled memory) data RAM(64 KB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(112 KB) base address in the alias region */ -#define SRAM2_BASE 0x2001C000U /*!< SRAM2(16 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define BKPSRAM_BASE 0x40024000U /*!< Backup SRAM(4 KB) base address in the alias region */ -#define FSMC_R_BASE 0xA0000000U /*!< FSMC registers base address */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(112 KB) base address in the bit-band region */ -#define SRAM2_BB_BASE 0x22380000U /*!< SRAM2(16 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define BKPSRAM_BB_BASE 0x42480000U /*!< Backup SRAM(4 KB) base address in the bit-band region */ -#define FLASH_END 0x080FFFFFU /*!< FLASH end address */ -#define CCMDATARAM_END 0x1000FFFFU /*!< CCM data RAM end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define TIM7_BASE (APB1PERIPH_BASE + 0x1400U) -#define TIM12_BASE (APB1PERIPH_BASE + 0x1800U) -#define TIM13_BASE (APB1PERIPH_BASE + 0x1C00U) -#define TIM14_BASE (APB1PERIPH_BASE + 0x2000U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define USART3_BASE (APB1PERIPH_BASE + 0x4800U) -#define UART4_BASE (APB1PERIPH_BASE + 0x4C00U) -#define UART5_BASE (APB1PERIPH_BASE + 0x5000U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define CAN1_BASE (APB1PERIPH_BASE + 0x6400U) -#define CAN2_BASE (APB1PERIPH_BASE + 0x6800U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) -#define DAC_BASE (APB1PERIPH_BASE + 0x7400U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define TIM8_BASE (APB2PERIPH_BASE + 0x0400U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC2_BASE (APB2PERIPH_BASE + 0x2100U) -#define ADC3_BASE (APB2PERIPH_BASE + 0x2200U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOF_BASE (AHB1PERIPH_BASE + 0x1400U) -#define GPIOG_BASE (AHB1PERIPH_BASE + 0x1800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define GPIOI_BASE (AHB1PERIPH_BASE + 0x2000U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) - -/*!< AHB2 peripherals */ -#define RNG_BASE (AHB2PERIPH_BASE + 0x60800U) - -/*!< FSMC Bankx registers base address */ -#define FSMC_Bank1_R_BASE (FSMC_R_BASE + 0x0000U) -#define FSMC_Bank1E_R_BASE (FSMC_R_BASE + 0x0104U) -#define FSMC_Bank2_3_R_BASE (FSMC_R_BASE + 0x0060U) -#define FSMC_Bank4_R_BASE (FSMC_R_BASE + 0x00A0U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_HS_PERIPH_BASE 0x40040000U -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define TIM7 ((TIM_TypeDef *) TIM7_BASE) -#define TIM12 ((TIM_TypeDef *) TIM12_BASE) -#define TIM13 ((TIM_TypeDef *) TIM13_BASE) -#define TIM14 ((TIM_TypeDef *) TIM14_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define USART3 ((USART_TypeDef *) USART3_BASE) -#define UART4 ((USART_TypeDef *) UART4_BASE) -#define UART5 ((USART_TypeDef *) UART5_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define CAN1 ((CAN_TypeDef *) CAN1_BASE) -#define CAN2 ((CAN_TypeDef *) CAN2_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define DAC ((DAC_TypeDef *) DAC_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define TIM8 ((TIM_TypeDef *) TIM8_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define ADC2 ((ADC_TypeDef *) ADC2_BASE) -#define ADC3 ((ADC_TypeDef *) ADC3_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOF ((GPIO_TypeDef *) GPIOF_BASE) -#define GPIOG ((GPIO_TypeDef *) GPIOG_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define GPIOI ((GPIO_TypeDef *) GPIOI_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) -#define FSMC_Bank1 ((FSMC_Bank1_TypeDef *) FSMC_Bank1_R_BASE) -#define FSMC_Bank1E ((FSMC_Bank1E_TypeDef *) FSMC_Bank1E_R_BASE) -#define FSMC_Bank2_3 ((FSMC_Bank2_3_TypeDef *) FSMC_Bank2_3_R_BASE) -#define FSMC_Bank4 ((FSMC_Bank4_TypeDef *) FSMC_Bank4_R_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) -#define USB_OTG_HS ((USB_OTG_GlobalTypeDef *) USB_OTG_HS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f407xx - * @{ - */ - -#ifndef __STM32F407xx_H -#define __STM32F407xx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1, ADC2 and ADC3 global Interrupts */ - CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */ - CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */ - CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ - CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - USART3_IRQn = 39, /*!< USART3 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */ - TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */ - TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */ - TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare Interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - FSMC_IRQn = 48, /*!< FSMC global Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - UART4_IRQn = 52, /*!< UART4 global Interrupt */ - UART5_IRQn = 53, /*!< UART5 global Interrupt */ - TIM6_DAC_IRQn = 54, /*!< TIM6 global and DAC1&2 underrun error interrupts */ - TIM7_IRQn = 55, /*!< TIM7 global interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - ETH_IRQn = 61, /*!< Ethernet global Interrupt */ - ETH_WKUP_IRQn = 62, /*!< Ethernet Wakeup through EXTI line Interrupt */ - CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */ - CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */ - CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */ - CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - OTG_HS_EP1_OUT_IRQn = 74, /*!< USB OTG HS End Point 1 Out global interrupt */ - OTG_HS_EP1_IN_IRQn = 75, /*!< USB OTG HS End Point 1 In global interrupt */ - OTG_HS_WKUP_IRQn = 76, /*!< USB OTG HS Wakeup through EXTI interrupt */ - OTG_HS_IRQn = 77, /*!< USB OTG HS global interrupt */ - DCMI_IRQn = 78, /*!< DCMI global interrupt */ - HASH_RNG_IRQn = 80, /*!< Hash and RNG global interrupt */ - FPU_IRQn = 81 /*!< FPU global interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - - -/** - * @brief Controller Area Network TxMailBox - */ - -typedef struct -{ - __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ - __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ - __IO uint32_t TDLR; /*!< CAN mailbox data low register */ - __IO uint32_t TDHR; /*!< CAN mailbox data high register */ -} CAN_TxMailBox_TypeDef; - -/** - * @brief Controller Area Network FIFOMailBox - */ - -typedef struct -{ - __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ - __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ - __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ - __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ -} CAN_FIFOMailBox_TypeDef; - -/** - * @brief Controller Area Network FilterRegister - */ - -typedef struct -{ - __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ - __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ -} CAN_FilterRegister_TypeDef; - -/** - * @brief Controller Area Network - */ - -typedef struct -{ - __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ - __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ - __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ - __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ - __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ - __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ - __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ - __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ - uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ - CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ - CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ - uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ - __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ - __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ - uint32_t RESERVED2; /*!< Reserved, 0x208 */ - __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ - uint32_t RESERVED3; /*!< Reserved, 0x210 */ - __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ - uint32_t RESERVED4; /*!< Reserved, 0x218 */ - __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ - uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ - CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ -} CAN_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Digital to Analog Converter - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ - __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ - __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ - __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ - __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ - __IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */ - __IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */ - __IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */ - __IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */ - __IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */ - __IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */ - __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ - __IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */ - __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ -} DAC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - -/** - * @brief DCMI - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DCMI control register 1, Address offset: 0x00 */ - __IO uint32_t SR; /*!< DCMI status register, Address offset: 0x04 */ - __IO uint32_t RISR; /*!< DCMI raw interrupt status register, Address offset: 0x08 */ - __IO uint32_t IER; /*!< DCMI interrupt enable register, Address offset: 0x0C */ - __IO uint32_t MISR; /*!< DCMI masked interrupt status register, Address offset: 0x10 */ - __IO uint32_t ICR; /*!< DCMI interrupt clear register, Address offset: 0x14 */ - __IO uint32_t ESCR; /*!< DCMI embedded synchronization code register, Address offset: 0x18 */ - __IO uint32_t ESUR; /*!< DCMI embedded synchronization unmask register, Address offset: 0x1C */ - __IO uint32_t CWSTRTR; /*!< DCMI crop window start, Address offset: 0x20 */ - __IO uint32_t CWSIZER; /*!< DCMI crop window size, Address offset: 0x24 */ - __IO uint32_t DR; /*!< DCMI data register, Address offset: 0x28 */ -} DCMI_TypeDef; - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - - -/** - * @brief Ethernet MAC - */ - -typedef struct -{ - __IO uint32_t MACCR; - __IO uint32_t MACFFR; - __IO uint32_t MACHTHR; - __IO uint32_t MACHTLR; - __IO uint32_t MACMIIAR; - __IO uint32_t MACMIIDR; - __IO uint32_t MACFCR; - __IO uint32_t MACVLANTR; /* 8 */ - uint32_t RESERVED0[2]; - __IO uint32_t MACRWUFFR; /* 11 */ - __IO uint32_t MACPMTCSR; - uint32_t RESERVED1[2]; - __IO uint32_t MACSR; /* 15 */ - __IO uint32_t MACIMR; - __IO uint32_t MACA0HR; - __IO uint32_t MACA0LR; - __IO uint32_t MACA1HR; - __IO uint32_t MACA1LR; - __IO uint32_t MACA2HR; - __IO uint32_t MACA2LR; - __IO uint32_t MACA3HR; - __IO uint32_t MACA3LR; /* 24 */ - uint32_t RESERVED2[40]; - __IO uint32_t MMCCR; /* 65 */ - __IO uint32_t MMCRIR; - __IO uint32_t MMCTIR; - __IO uint32_t MMCRIMR; - __IO uint32_t MMCTIMR; /* 69 */ - uint32_t RESERVED3[14]; - __IO uint32_t MMCTGFSCCR; /* 84 */ - __IO uint32_t MMCTGFMSCCR; - uint32_t RESERVED4[5]; - __IO uint32_t MMCTGFCR; - uint32_t RESERVED5[10]; - __IO uint32_t MMCRFCECR; - __IO uint32_t MMCRFAECR; - uint32_t RESERVED6[10]; - __IO uint32_t MMCRGUFCR; - uint32_t RESERVED7[334]; - __IO uint32_t PTPTSCR; - __IO uint32_t PTPSSIR; - __IO uint32_t PTPTSHR; - __IO uint32_t PTPTSLR; - __IO uint32_t PTPTSHUR; - __IO uint32_t PTPTSLUR; - __IO uint32_t PTPTSAR; - __IO uint32_t PTPTTHR; - __IO uint32_t PTPTTLR; - __IO uint32_t RESERVED8; - __IO uint32_t PTPTSSR; - uint32_t RESERVED9[565]; - __IO uint32_t DMABMR; - __IO uint32_t DMATPDR; - __IO uint32_t DMARPDR; - __IO uint32_t DMARDLAR; - __IO uint32_t DMATDLAR; - __IO uint32_t DMASR; - __IO uint32_t DMAOMR; - __IO uint32_t DMAIER; - __IO uint32_t DMAMFBOCR; - __IO uint32_t DMARSWTR; - uint32_t RESERVED10[8]; - __IO uint32_t DMACHTDR; - __IO uint32_t DMACHRDR; - __IO uint32_t DMACHTBAR; - __IO uint32_t DMACHRBAR; -} ETH_TypeDef; - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - - -/** - * @brief Flexible Static Memory Controller - */ - -typedef struct -{ - __IO uint32_t BTCR[8]; /*!< NOR/PSRAM chip-select control register(BCR) and chip-select timing register(BTR), Address offset: 0x00-1C */ -} FSMC_Bank1_TypeDef; - -/** - * @brief Flexible Static Memory Controller Bank1E - */ - -typedef struct -{ - __IO uint32_t BWTR[7]; /*!< NOR/PSRAM write timing registers, Address offset: 0x104-0x11C */ -} FSMC_Bank1E_TypeDef; - -/** - * @brief Flexible Static Memory Controller Bank2 - */ - -typedef struct -{ - __IO uint32_t PCR2; /*!< NAND Flash control register 2, Address offset: 0x60 */ - __IO uint32_t SR2; /*!< NAND Flash FIFO status and interrupt register 2, Address offset: 0x64 */ - __IO uint32_t PMEM2; /*!< NAND Flash Common memory space timing register 2, Address offset: 0x68 */ - __IO uint32_t PATT2; /*!< NAND Flash Attribute memory space timing register 2, Address offset: 0x6C */ - uint32_t RESERVED0; /*!< Reserved, 0x70 */ - __IO uint32_t ECCR2; /*!< NAND Flash ECC result registers 2, Address offset: 0x74 */ - uint32_t RESERVED1; /*!< Reserved, 0x78 */ - uint32_t RESERVED2; /*!< Reserved, 0x7C */ - __IO uint32_t PCR3; /*!< NAND Flash control register 3, Address offset: 0x80 */ - __IO uint32_t SR3; /*!< NAND Flash FIFO status and interrupt register 3, Address offset: 0x84 */ - __IO uint32_t PMEM3; /*!< NAND Flash Common memory space timing register 3, Address offset: 0x88 */ - __IO uint32_t PATT3; /*!< NAND Flash Attribute memory space timing register 3, Address offset: 0x8C */ - uint32_t RESERVED3; /*!< Reserved, 0x90 */ - __IO uint32_t ECCR3; /*!< NAND Flash ECC result registers 3, Address offset: 0x94 */ -} FSMC_Bank2_3_TypeDef; - -/** - * @brief Flexible Static Memory Controller Bank4 - */ - -typedef struct -{ - __IO uint32_t PCR4; /*!< PC Card control register 4, Address offset: 0xA0 */ - __IO uint32_t SR4; /*!< PC Card FIFO status and interrupt register 4, Address offset: 0xA4 */ - __IO uint32_t PMEM4; /*!< PC Card Common memory space timing register 4, Address offset: 0xA8 */ - __IO uint32_t PATT4; /*!< PC Card Attribute memory space timing register 4, Address offset: 0xAC */ - __IO uint32_t PIO4; /*!< PC Card I/O space timing register 4, Address offset: 0xB0 */ -} FSMC_Bank4_TypeDef; - - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - - -/** - * @brief __USB_OTG_Core_register - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register 000h*/ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register 004h*/ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register 008h*/ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register 00Ch*/ - __IO uint32_t GRSTCTL; /*!< Core Reset Register 010h*/ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register 014h*/ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register 018h*/ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register 01Ch*/ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register 020h*/ - __IO uint32_t GRXFSIZ; /* Receive FIFO Size Register 024h*/ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register 028h*/ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg 02Ch*/ - uint32_t Reserved30[2]; /* Reserved 030h*/ - __IO uint32_t GCCFG; /* General Purpose IO Register 038h*/ - __IO uint32_t CID; /* User ID Register 03Ch*/ - uint32_t Reserved40[48]; /* Reserved 040h-0FFh*/ - __IO uint32_t HPTXFSIZ; /* Host Periodic Tx FIFO Size Reg 100h*/ - __IO uint32_t DIEPTXF[0x0F];/* dev Periodic Transmit FIFO */ -} -USB_OTG_GlobalTypeDef; - - - -/** - * @brief __device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /* dev Configuration Register 800h*/ - __IO uint32_t DCTL; /* dev Control Register 804h*/ - __IO uint32_t DSTS; /* dev Status Register (RO) 808h*/ - uint32_t Reserved0C; /* Reserved 80Ch*/ - __IO uint32_t DIEPMSK; /* dev IN Endpoint Mask 810h*/ - __IO uint32_t DOEPMSK; /* dev OUT Endpoint Mask 814h*/ - __IO uint32_t DAINT; /* dev All Endpoints Itr Reg 818h*/ - __IO uint32_t DAINTMSK; /* dev All Endpoints Itr Mask 81Ch*/ - uint32_t Reserved20; /* Reserved 820h*/ - uint32_t Reserved9; /* Reserved 824h*/ - __IO uint32_t DVBUSDIS; /* dev VBUS discharge Register 828h*/ - __IO uint32_t DVBUSPULSE; /* dev VBUS Pulse Register 82Ch*/ - __IO uint32_t DTHRCTL; /* dev thr 830h*/ - __IO uint32_t DIEPEMPMSK; /* dev empty msk 834h*/ - __IO uint32_t DEACHINT; /* dedicated EP interrupt 838h*/ - __IO uint32_t DEACHMSK; /* dedicated EP msk 83Ch*/ - uint32_t Reserved40; /* dedicated EP mask 840h*/ - __IO uint32_t DINEP1MSK; /* dedicated EP mask 844h*/ - uint32_t Reserved44[15]; /* Reserved 844-87Ch*/ - __IO uint32_t DOUTEP1MSK; /* dedicated EP msk 884h*/ -} -USB_OTG_DeviceTypeDef; - - -/** - * @brief __IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /* dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved 900h + (ep_num * 20h) + 04h*/ - __IO uint32_t DIEPINT; /* dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved 900h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DIEPTSIZ; /* IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h*/ - __IO uint32_t DIEPDMA; /* IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h*/ - __IO uint32_t DTXFSTS;/*IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h*/ - uint32_t Reserved18; /* Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch*/ -} -USB_OTG_INEndpointTypeDef; - - -/** - * @brief __OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /* dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved B00h + (ep_num * 20h) + 04h*/ - __IO uint32_t DOEPINT; /* dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved B00h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DOEPTSIZ; /* dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h*/ - __IO uint32_t DOEPDMA; /* dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h*/ - uint32_t Reserved18[2]; /* Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch*/ -} -USB_OTG_OUTEndpointTypeDef; - - -/** - * @brief __Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /* Host Configuration Register 400h*/ - __IO uint32_t HFIR; /* Host Frame Interval Register 404h*/ - __IO uint32_t HFNUM; /* Host Frame Nbr/Frame Remaining 408h*/ - uint32_t Reserved40C; /* Reserved 40Ch*/ - __IO uint32_t HPTXSTS; /* Host Periodic Tx FIFO/ Queue Status 410h*/ - __IO uint32_t HAINT; /* Host All Channels Interrupt Register 414h*/ - __IO uint32_t HAINTMSK; /* Host All Channels Interrupt Mask 418h*/ -} -USB_OTG_HostTypeDef; - - -/** - * @brief __Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; - __IO uint32_t HCSPLT; - __IO uint32_t HCINT; - __IO uint32_t HCINTMSK; - __IO uint32_t HCTSIZ; - __IO uint32_t HCDMA; - uint32_t Reserved[2]; -} -USB_OTG_HostChannelTypeDef; - - -/** - * @brief Peripheral_memory_map - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define CCMDATARAM_BASE 0x10000000U /*!< CCM(core coupled memory) data RAM(64 KB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(112 KB) base address in the alias region */ -#define SRAM2_BASE 0x2001C000U /*!< SRAM2(16 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define BKPSRAM_BASE 0x40024000U /*!< Backup SRAM(4 KB) base address in the alias region */ -#define FSMC_R_BASE 0xA0000000U /*!< FSMC registers base address */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(112 KB) base address in the bit-band region */ -#define SRAM2_BB_BASE 0x22380000U /*!< SRAM2(16 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define BKPSRAM_BB_BASE 0x42480000U /*!< Backup SRAM(4 KB) base address in the bit-band region */ -#define FLASH_END 0x080FFFFFU /*!< FLASH end address */ -#define CCMDATARAM_END 0x1000FFFFU /*!< CCM data RAM end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define TIM7_BASE (APB1PERIPH_BASE + 0x1400U) -#define TIM12_BASE (APB1PERIPH_BASE + 0x1800U) -#define TIM13_BASE (APB1PERIPH_BASE + 0x1C00U) -#define TIM14_BASE (APB1PERIPH_BASE + 0x2000U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define USART3_BASE (APB1PERIPH_BASE + 0x4800U) -#define UART4_BASE (APB1PERIPH_BASE + 0x4C00U) -#define UART5_BASE (APB1PERIPH_BASE + 0x5000U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define CAN1_BASE (APB1PERIPH_BASE + 0x6400U) -#define CAN2_BASE (APB1PERIPH_BASE + 0x6800U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) -#define DAC_BASE (APB1PERIPH_BASE + 0x7400U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define TIM8_BASE (APB2PERIPH_BASE + 0x0400U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC2_BASE (APB2PERIPH_BASE + 0x2100U) -#define ADC3_BASE (APB2PERIPH_BASE + 0x2200U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOF_BASE (AHB1PERIPH_BASE + 0x1400U) -#define GPIOG_BASE (AHB1PERIPH_BASE + 0x1800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define GPIOI_BASE (AHB1PERIPH_BASE + 0x2000U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) -#define ETH_BASE (AHB1PERIPH_BASE + 0x8000U) -#define ETH_MAC_BASE (ETH_BASE) -#define ETH_MMC_BASE (ETH_BASE + 0x0100U) -#define ETH_PTP_BASE (ETH_BASE + 0x0700U) -#define ETH_DMA_BASE (ETH_BASE + 0x1000U) - -/*!< AHB2 peripherals */ -#define DCMI_BASE (AHB2PERIPH_BASE + 0x50000U) -#define RNG_BASE (AHB2PERIPH_BASE + 0x60800U) - -/*!< FSMC Bankx registers base address */ -#define FSMC_Bank1_R_BASE (FSMC_R_BASE + 0x0000U) -#define FSMC_Bank1E_R_BASE (FSMC_R_BASE + 0x0104U) -#define FSMC_Bank2_3_R_BASE (FSMC_R_BASE + 0x0060U) -#define FSMC_Bank4_R_BASE (FSMC_R_BASE + 0x00A0U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_HS_PERIPH_BASE 0x40040000U -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define TIM7 ((TIM_TypeDef *) TIM7_BASE) -#define TIM12 ((TIM_TypeDef *) TIM12_BASE) -#define TIM13 ((TIM_TypeDef *) TIM13_BASE) -#define TIM14 ((TIM_TypeDef *) TIM14_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define USART3 ((USART_TypeDef *) USART3_BASE) -#define UART4 ((USART_TypeDef *) UART4_BASE) -#define UART5 ((USART_TypeDef *) UART5_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define CAN1 ((CAN_TypeDef *) CAN1_BASE) -#define CAN2 ((CAN_TypeDef *) CAN2_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define DAC ((DAC_TypeDef *) DAC_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define TIM8 ((TIM_TypeDef *) TIM8_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define ADC2 ((ADC_TypeDef *) ADC2_BASE) -#define ADC3 ((ADC_TypeDef *) ADC3_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOF ((GPIO_TypeDef *) GPIOF_BASE) -#define GPIOG ((GPIO_TypeDef *) GPIOG_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define GPIOI ((GPIO_TypeDef *) GPIOI_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define ETH ((ETH_TypeDef *) ETH_BASE) -#define DCMI ((DCMI_TypeDef *) DCMI_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) -#define FSMC_Bank1 ((FSMC_Bank1_TypeDef *) FSMC_Bank1_R_BASE) -#define FSMC_Bank1E ((FSMC_Bank1E_TypeDef *) FSMC_Bank1E_R_BASE) -#define FSMC_Bank2_3 ((FSMC_Bank2_3_TypeDef *) FSMC_Bank2_3_R_BASE) -#define FSMC_Bank4 ((FSMC_Bank4_TypeDef *) FSMC_Bank4_R_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) -#define USB_OTG_HS ((USB_OTG_GlobalTypeDef *) USB_OTG_HS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f410cx - * @{ - */ - -#ifndef __STM32F410Cx_H -#define __STM32F410Cx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1 global Interrupts */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_IRQn = 25, /*!< TIM1 Update Interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - TIM6_DAC_IRQn = 54, /*!< TIM6 global Interrupt and DAC Global Interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - RNG_IRQn = 80, /*!< RNG global Interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - SPI5_IRQn = 85, /*!< SPI5 global Interrupt */ - FMPI2C1_EV_IRQn = 95, /*!< FMPI2C1 Event Interrupt */ - FMPI2C1_ER_IRQn = 96, /*!< FMPI2C1 Error Interrupt */ - LPTIM1_IRQn = 97 /*!< LPTIM1 interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Digital to Analog Converter - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ - __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ - __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ - __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ - __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ - __IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */ - __IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */ - __IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */ - __IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */ - __IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */ - __IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */ - __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ - __IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */ - __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ -} DAC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED; /*!< Reserved, 0x18 */ - uint32_t CFGR2; /*!< Reserved, 0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x24-0x28 */ - __IO uint32_t CFGR; /*!< SYSCFG Configuration register, Address offset: 0x2C */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< FMPI2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< FMPI2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< FMPI2C Own address 1 register, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< FMPI2C Own address 2 register, Address offset: 0x0C */ - __IO uint32_t TIMINGR; /*!< FMPI2C Timing register, Address offset: 0x10 */ - __IO uint32_t TIMEOUTR; /*!< FMPI2C Timeout register, Address offset: 0x14 */ - __IO uint32_t ISR; /*!< FMPI2C Interrupt and status register, Address offset: 0x18 */ - __IO uint32_t ICR; /*!< FMPI2C Interrupt clear register, Address offset: 0x1C */ - __IO uint32_t PECR; /*!< FMPI2C PEC register, Address offset: 0x20 */ - __IO uint32_t RXDR; /*!< FMPI2C Receive data register, Address offset: 0x24 */ - __IO uint32_t TXDR; /*!< FMPI2C Transmit data register, Address offset: 0x28 */ -} FMPI2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - uint32_t RESERVED0[3]; /*!< Reserved, 0x14-0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - uint32_t RESERVED2[3]; /*!< Reserved, 0x34-0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - uint32_t RESERVED4[3]; /*!< Reserved, 0x54-0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - uint32_t RESERVED7[2]; /*!< Reserved, 0x84-0x88 */ - __IO uint32_t DCKCFGR; /*!< RCC Dedicated Clocks configuration register, Address offset: 0x8C */ - __IO uint32_t CKGATENR; /*!< RCC Clocks Gated ENable Register, Address offset: 0x90 */ - __IO uint32_t DCKCFGR2; /*!< RCC Dedicated Clocks configuration register 2, Address offset: 0x94 */ - -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - -/** - * @brief LPTIMER - */ -typedef struct -{ - __IO uint32_t ISR; /*!< LPTIM Interrupt and Status register, Address offset: 0x00 */ - __IO uint32_t ICR; /*!< LPTIM Interrupt Clear register, Address offset: 0x04 */ - __IO uint32_t IER; /*!< LPTIM Interrupt Enable register, Address offset: 0x08 */ - __IO uint32_t CFGR; /*!< LPTIM Configuration register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< LPTIM Control register, Address offset: 0x10 */ - __IO uint32_t CMP; /*!< LPTIM Compare register, Address offset: 0x14 */ - __IO uint32_t ARR; /*!< LPTIM Autoreload register, Address offset: 0x18 */ - __IO uint32_t CNT; /*!< LPTIM Counter register, Address offset: 0x1C */ - __IO uint32_t OR; /*!< LPTIM Option register, Address offset: 0x20 */ -} LPTIM_TypeDef; - -/** - * @brief Peripheral_memory_map - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(32 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(32 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define FLASH_END 0x0801FFFFU /*!< FLASH end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) - -/*!< APB1 peripherals */ -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define LPTIM1_BASE (APB1PERIPH_BASE + 0x2400U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define FMPI2C1_BASE (APB1PERIPH_BASE + 0x6000U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) -#define DAC_BASE (APB1PERIPH_BASE + 0x7400U) -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) -#define SPI5_BASE (APB2PERIPH_BASE + 0x5000U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) -#define RNG_BASE (PERIPH_BASE + 0x80000U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define FMPI2C1 ((FMPI2C_TypeDef *) FMPI2C1_BASE) -#define LPTIM1 ((LPTIM_TypeDef *) LPTIM1_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define DAC ((DAC_TypeDef *) DAC_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define SPI5 ((SPI_TypeDef *) SPI5_BASE) -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f410rx - * @{ - */ - -#ifndef __STM32F410Rx_H -#define __STM32F410Rx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1 global Interrupts */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_IRQn = 25, /*!< TIM1 Update Interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - TIM6_DAC_IRQn = 54, /*!< TIM6 global Interrupt and DAC Global Interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - RNG_IRQn = 80, /*!< RNG global Interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - SPI5_IRQn = 85, /*!< SPI5 global Interrupt */ - FMPI2C1_EV_IRQn = 95, /*!< FMPI2C1 Event Interrupt */ - FMPI2C1_ER_IRQn = 96, /*!< FMPI2C1 Error Interrupt */ - LPTIM1_IRQn = 97 /*!< LPTIM1 interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Digital to Analog Converter - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ - __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ - __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ - __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ - __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ - __IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */ - __IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */ - __IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */ - __IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */ - __IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */ - __IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */ - __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ - __IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */ - __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ -} DAC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED; /*!< Reserved, 0x18 */ - uint32_t CFGR2; /*!< Reserved, 0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x24-0x28 */ - __IO uint32_t CFGR; /*!< SYSCFG Configuration register, Address offset: 0x2C */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< FMPI2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< FMPI2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< FMPI2C Own address 1 register, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< FMPI2C Own address 2 register, Address offset: 0x0C */ - __IO uint32_t TIMINGR; /*!< FMPI2C Timing register, Address offset: 0x10 */ - __IO uint32_t TIMEOUTR; /*!< FMPI2C Timeout register, Address offset: 0x14 */ - __IO uint32_t ISR; /*!< FMPI2C Interrupt and status register, Address offset: 0x18 */ - __IO uint32_t ICR; /*!< FMPI2C Interrupt clear register, Address offset: 0x1C */ - __IO uint32_t PECR; /*!< FMPI2C PEC register, Address offset: 0x20 */ - __IO uint32_t RXDR; /*!< FMPI2C Receive data register, Address offset: 0x24 */ - __IO uint32_t TXDR; /*!< FMPI2C Transmit data register, Address offset: 0x28 */ -} FMPI2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - uint32_t RESERVED0[3]; /*!< Reserved, 0x14-0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - uint32_t RESERVED2[3]; /*!< Reserved, 0x34-0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - uint32_t RESERVED4[3]; /*!< Reserved, 0x54-0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - uint32_t RESERVED7[2]; /*!< Reserved, 0x84-0x88 */ - __IO uint32_t DCKCFGR; /*!< RCC Dedicated Clocks configuration register, Address offset: 0x8C */ - __IO uint32_t CKGATENR; /*!< RCC Clocks Gated ENable Register, Address offset: 0x90 */ - __IO uint32_t DCKCFGR2; /*!< RCC Dedicated Clocks configuration register 2, Address offset: 0x94 */ - -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - -/** - * @brief LPTIMER - */ -typedef struct -{ - __IO uint32_t ISR; /*!< LPTIM Interrupt and Status register, Address offset: 0x00 */ - __IO uint32_t ICR; /*!< LPTIM Interrupt Clear register, Address offset: 0x04 */ - __IO uint32_t IER; /*!< LPTIM Interrupt Enable register, Address offset: 0x08 */ - __IO uint32_t CFGR; /*!< LPTIM Configuration register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< LPTIM Control register, Address offset: 0x10 */ - __IO uint32_t CMP; /*!< LPTIM Compare register, Address offset: 0x14 */ - __IO uint32_t ARR; /*!< LPTIM Autoreload register, Address offset: 0x18 */ - __IO uint32_t CNT; /*!< LPTIM Counter register, Address offset: 0x1C */ - __IO uint32_t OR; /*!< LPTIM Option register, Address offset: 0x20 */ -} LPTIM_TypeDef; - -/** - * @brief Peripheral_memory_map - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(32 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(32 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define FLASH_END 0x0801FFFFU /*!< FLASH end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) - -/*!< APB1 peripherals */ -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define LPTIM1_BASE (APB1PERIPH_BASE + 0x2400U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define FMPI2C1_BASE (APB1PERIPH_BASE + 0x6000U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) -#define DAC_BASE (APB1PERIPH_BASE + 0x7400U) -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) -#define SPI5_BASE (APB2PERIPH_BASE + 0x5000U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) -#define RNG_BASE (PERIPH_BASE + 0x80000U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define FMPI2C1 ((FMPI2C_TypeDef *) FMPI2C1_BASE) -#define LPTIM1 ((LPTIM_TypeDef *) LPTIM1_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define DAC ((DAC_TypeDef *) DAC_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define SPI5 ((SPI_TypeDef *) SPI5_BASE) -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f410tx - * @{ - */ - -#ifndef __STM32F410Tx_H -#define __STM32F410Tx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1 global Interrupts */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_IRQn = 25, /*!< TIM1 Update Interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - TIM6_DAC_IRQn = 54, /*!< TIM6 global Interrupt and DAC Global Interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - RNG_IRQn = 80, /*!< RNG global Interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - FMPI2C1_EV_IRQn = 95, /*!< FMPI2C1 Event Interrupt */ - FMPI2C1_ER_IRQn = 96, /*!< FMPI2C1 Error Interrupt */ - LPTIM1_IRQn = 97 /*!< LPTIM1 interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Digital to Analog Converter - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ - __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ - __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ - __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ - __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ - __IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */ - __IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */ - __IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */ - __IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */ - __IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */ - __IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */ - __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ - __IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */ - __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ -} DAC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED; /*!< Reserved, 0x18 */ - uint32_t CFGR2; /*!< Reserved, 0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x24-0x28 */ - __IO uint32_t CFGR; /*!< SYSCFG Configuration register, Address offset: 0x2C */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< FMPI2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< FMPI2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< FMPI2C Own address 1 register, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< FMPI2C Own address 2 register, Address offset: 0x0C */ - __IO uint32_t TIMINGR; /*!< FMPI2C Timing register, Address offset: 0x10 */ - __IO uint32_t TIMEOUTR; /*!< FMPI2C Timeout register, Address offset: 0x14 */ - __IO uint32_t ISR; /*!< FMPI2C Interrupt and status register, Address offset: 0x18 */ - __IO uint32_t ICR; /*!< FMPI2C Interrupt clear register, Address offset: 0x1C */ - __IO uint32_t PECR; /*!< FMPI2C PEC register, Address offset: 0x20 */ - __IO uint32_t RXDR; /*!< FMPI2C Receive data register, Address offset: 0x24 */ - __IO uint32_t TXDR; /*!< FMPI2C Transmit data register, Address offset: 0x28 */ -} FMPI2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - uint32_t RESERVED0[3]; /*!< Reserved, 0x14-0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - uint32_t RESERVED2[3]; /*!< Reserved, 0x34-0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - uint32_t RESERVED4[3]; /*!< Reserved, 0x54-0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - uint32_t RESERVED7[2]; /*!< Reserved, 0x84-0x88 */ - __IO uint32_t DCKCFGR; /*!< RCC Dedicated Clocks configuration register, Address offset: 0x8C */ - __IO uint32_t CKGATENR; /*!< RCC Clocks Gated ENable Register, Address offset: 0x90 */ - __IO uint32_t DCKCFGR2; /*!< RCC Dedicated Clocks configuration register 2, Address offset: 0x94 */ - -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - -/** - * @brief LPTIMER - */ -typedef struct -{ - __IO uint32_t ISR; /*!< LPTIM Interrupt and Status register, Address offset: 0x00 */ - __IO uint32_t ICR; /*!< LPTIM Interrupt Clear register, Address offset: 0x04 */ - __IO uint32_t IER; /*!< LPTIM Interrupt Enable register, Address offset: 0x08 */ - __IO uint32_t CFGR; /*!< LPTIM Configuration register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< LPTIM Control register, Address offset: 0x10 */ - __IO uint32_t CMP; /*!< LPTIM Compare register, Address offset: 0x14 */ - __IO uint32_t ARR; /*!< LPTIM Autoreload register, Address offset: 0x18 */ - __IO uint32_t CNT; /*!< LPTIM Counter register, Address offset: 0x1C */ - __IO uint32_t OR; /*!< LPTIM Option register, Address offset: 0x20 */ -} LPTIM_TypeDef; - -/** - * @brief Peripheral_memory_map - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(32 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(32 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define FLASH_END 0x0801FFFFU /*!< FLASH end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) - -/*!< APB1 peripherals */ -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define LPTIM1_BASE (APB1PERIPH_BASE + 0x2400U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define FMPI2C1_BASE (APB1PERIPH_BASE + 0x6000U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) -#define DAC_BASE (APB1PERIPH_BASE + 0x7400U) -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) -#define RNG_BASE (PERIPH_BASE + 0x80000U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define FMPI2C1 ((FMPI2C_TypeDef *) FMPI2C1_BASE) -#define LPTIM1 ((LPTIM_TypeDef *) LPTIM1_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define DAC ((DAC_TypeDef *) DAC_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f411xe - * @{ - */ - -#ifndef __STM32F411xE_H -#define __STM32F411xE_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1, ADC2 and ADC3 global Interrupts */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - SPI4_IRQn = 84, /*!< SPI4 global Interrupt */ - SPI5_IRQn = 85 /*!< SPI5 global Interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - uint32_t RESERVED7[1]; /*!< Reserved, 0x88 */ - __IO uint32_t DCKCFGR; /*!< RCC DCKCFGR configuration register, Address offset: 0x8C */ -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - - -/** - * @brief __USB_OTG_Core_register - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register Address offset : 0x00 */ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register Address offset : 0x04 */ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register Address offset : 0x08 */ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register Address offset : 0x0C */ - __IO uint32_t GRSTCTL; /*!< Core Reset Register Address offset : 0x10 */ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register Address offset : 0x14 */ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register Address offset : 0x18 */ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register Address offset : 0x1C */ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register Address offset : 0x20 */ - __IO uint32_t GRXFSIZ; /* Receive FIFO Size Register Address offset : 0x24 */ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register Address offset : 0x28 */ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg Address offset : 0x2C */ - uint32_t Reserved30[2]; /* Reserved Address offset : 0x30 */ - __IO uint32_t GCCFG; /*!< General Purpose IO Register Address offset : 0x38 */ - __IO uint32_t CID; /*!< User ID Register Address offset : 0x3C */ - uint32_t Reserved40[48]; /*!< Reserved Address offset : 0x40-0xFF */ - __IO uint32_t HPTXFSIZ; /*!< Host Periodic Tx FIFO Size Reg Address offset : 0x100 */ - __IO uint32_t DIEPTXF[0x0F]; /*!< dev Periodic Transmit FIFO */ -} -USB_OTG_GlobalTypeDef; - - - -/** - * @brief __device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /*!< dev Configuration Register Address offset : 0x800 */ - __IO uint32_t DCTL; /*!< dev Control Register Address offset : 0x804 */ - __IO uint32_t DSTS; /*!< dev Status Register (RO) Address offset : 0x808 */ - uint32_t Reserved0C; /*!< Reserved Address offset : 0x80C */ - __IO uint32_t DIEPMSK; /* !< dev IN Endpoint Mask Address offset : 0x810 */ - __IO uint32_t DOEPMSK; /*!< dev OUT Endpoint Mask Address offset : 0x814 */ - __IO uint32_t DAINT; /*!< dev All Endpoints Itr Reg Address offset : 0x818 */ - __IO uint32_t DAINTMSK; /*!< dev All Endpoints Itr Mask Address offset : 0x81C */ - uint32_t Reserved20; /*!< Reserved Address offset : 0x820 */ - uint32_t Reserved9; /*!< Reserved Address offset : 0x824 */ - __IO uint32_t DVBUSDIS; /*!< dev VBUS discharge Register Address offset : 0x828 */ - __IO uint32_t DVBUSPULSE; /*!< dev VBUS Pulse Register Address offset : 0x82C */ - __IO uint32_t DTHRCTL; /*!< dev thr Address offset : 0x830 */ - __IO uint32_t DIEPEMPMSK; /*!< dev empty msk Address offset : 0x834 */ - __IO uint32_t DEACHINT; /*!< dedicated EP interrupt Address offset : 0x838 */ - __IO uint32_t DEACHMSK; /*!< dedicated EP msk Address offset : 0x83C */ - uint32_t Reserved40; /*!< dedicated EP mask Address offset : 0x840 */ - __IO uint32_t DINEP1MSK; /*!< dedicated EP mask Address offset : 0x844 */ - uint32_t Reserved44[15]; /*!< Reserved Address offset : 0x844-0x87C */ - __IO uint32_t DOUTEP1MSK; /*!< dedicated EP msk Address offset : 0x884 */ -} -USB_OTG_DeviceTypeDef; - - -/** - * @brief __IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /* dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /* Reserved 900h + (ep_num * 20h) + 04h */ - __IO uint32_t DIEPINT; /* dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /* Reserved 900h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DIEPTSIZ; /* IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h */ - __IO uint32_t DIEPDMA; /* IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h */ - __IO uint32_t DTXFSTS; /*IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h */ - uint32_t Reserved18; /* Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch */ -} -USB_OTG_INEndpointTypeDef; - - -/** - * @brief __OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /* dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved B00h + (ep_num * 20h) + 04h*/ - __IO uint32_t DOEPINT; /* dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved B00h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DOEPTSIZ; /* dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h*/ - __IO uint32_t DOEPDMA; /* dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h*/ - uint32_t Reserved18[2]; /* Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch*/ -} -USB_OTG_OUTEndpointTypeDef; - - -/** - * @brief __Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /* Host Configuration Register 400h*/ - __IO uint32_t HFIR; /* Host Frame Interval Register 404h*/ - __IO uint32_t HFNUM; /* Host Frame Nbr/Frame Remaining 408h*/ - uint32_t Reserved40C; /* Reserved 40Ch*/ - __IO uint32_t HPTXSTS; /* Host Periodic Tx FIFO/ Queue Status 410h*/ - __IO uint32_t HAINT; /* Host All Channels Interrupt Register 414h*/ - __IO uint32_t HAINTMSK; /* Host All Channels Interrupt Mask 418h*/ -} -USB_OTG_HostTypeDef; - - -/** - * @brief __Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; - __IO uint32_t HCSPLT; - __IO uint32_t HCINT; - __IO uint32_t HCINTMSK; - __IO uint32_t HCTSIZ; - __IO uint32_t HCDMA; - uint32_t Reserved[2]; -} -USB_OTG_HostChannelTypeDef; - - -/** - * @brief Peripheral_memory_map - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(128 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define BKPSRAM_BASE 0x40024000U /*!< Backup SRAM(4 KB) base address in the alias region */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(128 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define BKPSRAM_BB_BASE 0x42480000U /*!< Backup SRAM(4 KB) base address in the bit-band region */ -#define FLASH_END 0x0807FFFFU /*!< FLASH end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SPI4_BASE (APB2PERIPH_BASE + 0x3400U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) -#define SPI5_BASE (APB2PERIPH_BASE + 0x5000U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SPI4 ((SPI_TypeDef *) SPI4_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define SPI5 ((SPI_TypeDef *) SPI5_BASE) -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f412cx - * @{ - */ - -#ifndef __STM32F412Cx_H -#define __STM32F412Cx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1 global Interrupts */ - CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */ - CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */ - CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ - CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */ - TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */ - TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */ - TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare Interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - TIM6_IRQn = 54, /*!< TIM6 global interrupt */ - TIM7_IRQn = 55, /*!< TIM7 global interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - DFSDM1_FLT0_IRQn = 61, /*!< DFSDM1 Filter 0 global Interrupt */ - DFSDM1_FLT1_IRQn = 62, /*!< DFSDM1 Filter 1 global Interrupt */ - CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */ - CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */ - CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */ - CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - RNG_IRQn = 80, /*!< RNG global Interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - SPI4_IRQn = 84, /*!< SPI4 global Interrupt */ - SPI5_IRQn = 85, /*!< SPI5 global Interrupt */ - FMPI2C1_EV_IRQn = 95, /*!< FMPI2C1 Event Interrupt */ - FMPI2C1_ER_IRQn = 96 /*!< FMPI2C1 Error Interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - -/** - * @brief Controller Area Network TxMailBox - */ - -typedef struct -{ - __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ - __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ - __IO uint32_t TDLR; /*!< CAN mailbox data low register */ - __IO uint32_t TDHR; /*!< CAN mailbox data high register */ -} CAN_TxMailBox_TypeDef; - -/** - * @brief Controller Area Network FIFOMailBox - */ - -typedef struct -{ - __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ - __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ - __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ - __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ -} CAN_FIFOMailBox_TypeDef; - -/** - * @brief Controller Area Network FilterRegister - */ - -typedef struct -{ - __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ - __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ -} CAN_FilterRegister_TypeDef; - -typedef struct -{ - __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ - __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ - __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ - __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ - __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ - __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ - __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ - __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ - uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ - CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ - CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ - uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ - __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ - __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ - uint32_t RESERVED2; /*!< Reserved, 0x208 */ - __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ - uint32_t RESERVED3; /*!< Reserved, 0x210 */ - __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ - uint32_t RESERVED4; /*!< Reserved, 0x218 */ - __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ - uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ - CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ -} CAN_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief DFSDM module registers - */ -typedef struct -{ - __IO uint32_t FLTCR1; /*!< DFSDM control register1, Address offset: 0x100 */ - __IO uint32_t FLTCR2; /*!< DFSDM control register2, Address offset: 0x104 */ - __IO uint32_t FLTISR; /*!< DFSDM interrupt and status register, Address offset: 0x108 */ - __IO uint32_t FLTICR; /*!< DFSDM interrupt flag clear register, Address offset: 0x10C */ - __IO uint32_t FLTJCHGR; /*!< DFSDM injected channel group selection register, Address offset: 0x110 */ - __IO uint32_t FLTFCR; /*!< DFSDM filter control register, Address offset: 0x114 */ - __IO uint32_t FLTJDATAR; /*!< DFSDM data register for injected group, Address offset: 0x118 */ - __IO uint32_t FLTRDATAR; /*!< DFSDM data register for regular group, Address offset: 0x11C */ - __IO uint32_t FLTAWHTR; /*!< DFSDM analog watchdog high threshold register, Address offset: 0x120 */ - __IO uint32_t FLTAWLTR; /*!< DFSDM analog watchdog low threshold register, Address offset: 0x124 */ - __IO uint32_t FLTAWSR; /*!< DFSDM analog watchdog status register Address offset: 0x128 */ - __IO uint32_t FLTAWCFR; /*!< DFSDM analog watchdog clear flag register Address offset: 0x12C */ - __IO uint32_t FLTEXMAX; /*!< DFSDM extreme detector maximum register, Address offset: 0x130 */ - __IO uint32_t FLTEXMIN; /*!< DFSDM extreme detector minimum register Address offset: 0x134 */ - __IO uint32_t FLTCNVTIMR; /*!< DFSDM conversion timer, Address offset: 0x138 */ -} DFSDM_Filter_TypeDef; - -/** - * @brief DFSDM channel configuration registers - */ -typedef struct -{ - __IO uint32_t CHCFGR1; /*!< DFSDM channel configuration register1, Address offset: 0x00 */ - __IO uint32_t CHCFGR2; /*!< DFSDM channel configuration register2, Address offset: 0x04 */ - __IO uint32_t CHAWSCDR; /*!< DFSDM channel analog watchdog and - short circuit detector register, Address offset: 0x08 */ - __IO uint32_t CHWDATAR; /*!< DFSDM channel watchdog filter data register, Address offset: 0x0C */ - __IO uint32_t CHDATINR; /*!< DFSDM channel data input register, Address offset: 0x10 */ -} DFSDM_Channel_TypeDef; - -/** - * @brief Debug MCU - */ -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x24-0x28 */ - __IO uint32_t CFGR; /*!< SYSCFG Configuration register, Address offset: 0x2C */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< FMPI2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< FMPI2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< FMPI2C Own address 1 register, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< FMPI2C Own address 2 register, Address offset: 0x0C */ - __IO uint32_t TIMINGR; /*!< FMPI2C Timing register, Address offset: 0x10 */ - __IO uint32_t TIMEOUTR; /*!< FMPI2C Timeout register, Address offset: 0x14 */ - __IO uint32_t ISR; /*!< FMPI2C Interrupt and status register, Address offset: 0x18 */ - __IO uint32_t ICR; /*!< FMPI2C Interrupt clear register, Address offset: 0x1C */ - __IO uint32_t PECR; /*!< FMPI2C PEC register, Address offset: 0x20 */ - __IO uint32_t RXDR; /*!< FMPI2C Receive data register, Address offset: 0x24 */ - __IO uint32_t TXDR; /*!< FMPI2C Transmit data register, Address offset: 0x28 */ -} FMPI2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - uint32_t RESERVED2[2]; /*!< Reserved, 0x38-0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - uint32_t RESERVED4[2]; /*!< Reserved, 0x58-0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - uint32_t RESERVED7; /*!< Reserved, 0x84 */ - __IO uint32_t DCKCFGR; /*!< RCC Dedicated Clocks configuration register, Address offset: 0x8C */ - __IO uint32_t CKGATENR; /*!< RCC Clocks Gated ENable Register, Address offset: 0x90 */ - __IO uint32_t DCKCFGR2; /*!< RCC Dedicated Clocks configuration register 2, Address offset: 0x94 */ -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - -/** - * @brief USB_OTG_Core_Registers - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register 000h*/ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register 004h*/ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register 008h*/ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register 00Ch*/ - __IO uint32_t GRSTCTL; /*!< Core Reset Register 010h*/ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register 014h*/ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register 018h*/ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register 01Ch*/ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register 020h*/ - __IO uint32_t GRXFSIZ; /*!< Receive FIFO Size Register 024h*/ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register 028h*/ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg 02Ch*/ - uint32_t Reserved30[2]; /*!< Reserved 030h*/ - __IO uint32_t GCCFG; /*!< General Purpose IO Register 038h*/ - __IO uint32_t CID; /*!< User ID Register 03Ch*/ - uint32_t Reserved5[3]; /*!< Reserved 040h-048h*/ - __IO uint32_t GHWCFG3; /*!< User HW config3 04Ch*/ - uint32_t Reserved6; /*!< Reserved 050h*/ - __IO uint32_t GLPMCFG; /*!< LPM Register 054h*/ - uint32_t Reserved; /*!< Reserved 058h */ - __IO uint32_t GDFIFOCFG; /*!< DFIFO Software Config Register 05Ch*/ - uint32_t Reserved43[40]; /*!< Reserved 058h-0FFh*/ - __IO uint32_t HPTXFSIZ; /*!< Host Periodic Tx FIFO Size Reg 100h*/ - __IO uint32_t DIEPTXF[0x0F]; /*!< dev Periodic Transmit FIFO */ -} USB_OTG_GlobalTypeDef; - - -/** - * @brief USB_OTG_device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /*!< dev Configuration Register 800h */ - __IO uint32_t DCTL; /*!< dev Control Register 804h */ - __IO uint32_t DSTS; /*!< dev Status Register (RO) 808h */ - uint32_t Reserved0C; /*!< Reserved 80Ch */ - __IO uint32_t DIEPMSK; /*!< dev IN Endpoint Mask 810h */ - __IO uint32_t DOEPMSK; /*!< dev OUT Endpoint Mask 814h */ - __IO uint32_t DAINT; /*!< dev All Endpoints Itr Reg 818h */ - __IO uint32_t DAINTMSK; /*!< dev All Endpoints Itr Mask 81Ch */ - uint32_t Reserved20; /*!< Reserved 820h */ - uint32_t Reserved9; /*!< Reserved 824h */ - __IO uint32_t DVBUSDIS; /*!< dev VBUS discharge Register 828h */ - __IO uint32_t DVBUSPULSE; /*!< dev VBUS Pulse Register 82Ch */ - __IO uint32_t DTHRCTL; /*!< dev threshold 830h */ - __IO uint32_t DIEPEMPMSK; /*!< dev empty msk 834h */ - __IO uint32_t DEACHINT; /*!< dedicated EP interrupt 838h */ - __IO uint32_t DEACHMSK; /*!< dedicated EP msk 83Ch */ - uint32_t Reserved40; /*!< dedicated EP mask 840h */ - __IO uint32_t DINEP1MSK; /*!< dedicated EP mask 844h */ - uint32_t Reserved44[15]; /*!< Reserved 844-87Ch */ - __IO uint32_t DOUTEP1MSK; /*!< dedicated EP msk 884h */ -} USB_OTG_DeviceTypeDef; - - -/** - * @brief USB_OTG_IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /*!< dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /*!< Reserved 900h + (ep_num * 20h) + 04h */ - __IO uint32_t DIEPINT; /*!< dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /*!< Reserved 900h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DIEPTSIZ; /*!< IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h */ - __IO uint32_t DIEPDMA; /*!< IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h */ - __IO uint32_t DTXFSTS; /*!< IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h */ - uint32_t Reserved18; /*!< Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch */ -} USB_OTG_INEndpointTypeDef; - - -/** - * @brief USB_OTG_OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /*!< dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /*!< Reserved B00h + (ep_num * 20h) + 04h */ - __IO uint32_t DOEPINT; /*!< dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /*!< Reserved B00h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DOEPTSIZ; /*!< dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h */ - __IO uint32_t DOEPDMA; /*!< dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h */ - uint32_t Reserved18[2]; /*!< Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch */ -} USB_OTG_OUTEndpointTypeDef; - - -/** - * @brief USB_OTG_Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /*!< Host Configuration Register 400h */ - __IO uint32_t HFIR; /*!< Host Frame Interval Register 404h */ - __IO uint32_t HFNUM; /*!< Host Frame Nbr/Frame Remaining 408h */ - uint32_t Reserved40C; /*!< Reserved 40Ch */ - __IO uint32_t HPTXSTS; /*!< Host Periodic Tx FIFO/ Queue Status 410h */ - __IO uint32_t HAINT; /*!< Host All Channels Interrupt Register 414h */ - __IO uint32_t HAINTMSK; /*!< Host All Channels Interrupt Mask 418h */ -} USB_OTG_HostTypeDef; - - -/** - * @brief USB_OTG_Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; /*!< Host Channel Characteristics Register 500h */ - __IO uint32_t HCSPLT; /*!< Host Channel Split Control Register 504h */ - __IO uint32_t HCINT; /*!< Host Channel Interrupt Register 508h */ - __IO uint32_t HCINTMSK; /*!< Host Channel Interrupt Mask Register 50Ch */ - __IO uint32_t HCTSIZ; /*!< Host Channel Transfer Size Register 510h */ - __IO uint32_t HCDMA; /*!< Host Channel DMA Address Register 514h */ - uint32_t Reserved[2]; /*!< Reserved */ -} USB_OTG_HostChannelTypeDef; - - -/** - * @brief Peripheral_memory_map - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(256 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ - -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(256 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define FLASH_END 0x080FFFFFU /*!< FLASH end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define TIM7_BASE (APB1PERIPH_BASE + 0x1400U) -#define TIM12_BASE (APB1PERIPH_BASE + 0x1800U) -#define TIM13_BASE (APB1PERIPH_BASE + 0x1C00U) -#define TIM14_BASE (APB1PERIPH_BASE + 0x2000U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define FMPI2C1_BASE (APB1PERIPH_BASE + 0x6000U) -#define CAN1_BASE (APB1PERIPH_BASE + 0x6400U) -#define CAN2_BASE (APB1PERIPH_BASE + 0x6800U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define TIM8_BASE (APB2PERIPH_BASE + 0x0400U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SPI4_BASE (APB2PERIPH_BASE + 0x3400U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) -#define SPI5_BASE (APB2PERIPH_BASE + 0x5000U) -#define DFSDM1_BASE (APB2PERIPH_BASE + 0x6000U) -#define DFSDM1_Channel0_BASE (DFSDM1_BASE + 0x00U) -#define DFSDM1_Channel1_BASE (DFSDM1_BASE + 0x20U) -#define DFSDM1_Channel2_BASE (DFSDM1_BASE + 0x40U) -#define DFSDM1_Channel3_BASE (DFSDM1_BASE + 0x60U) -#define DFSDM1_Filter0_BASE (DFSDM1_BASE + 0x100U) -#define DFSDM1_Filter1_BASE (DFSDM1_BASE + 0x180U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOF_BASE (AHB1PERIPH_BASE + 0x1400U) -#define GPIOG_BASE (AHB1PERIPH_BASE + 0x1800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) - -/*!< AHB2 peripherals */ -#define RNG_BASE (AHB2PERIPH_BASE + 0x60800U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define TIM7 ((TIM_TypeDef *) TIM7_BASE) -#define TIM12 ((TIM_TypeDef *) TIM12_BASE) -#define TIM13 ((TIM_TypeDef *) TIM13_BASE) -#define TIM14 ((TIM_TypeDef *) TIM14_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define FMPI2C1 ((FMPI2C_TypeDef *) FMPI2C1_BASE) -#define CAN1 ((CAN_TypeDef *) CAN1_BASE) -#define CAN2 ((CAN_TypeDef *) CAN2_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define TIM8 ((TIM_TypeDef *) TIM8_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SPI4 ((SPI_TypeDef *) SPI4_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define SPI5 ((SPI_TypeDef *) SPI5_BASE) -#define DFSDM1_Channel0 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel0_BASE) -#define DFSDM1_Channel1 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel1_BASE) -#define DFSDM1_Channel2 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel2_BASE) -#define DFSDM1_Channel3 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel3_BASE) -#define DFSDM1_Filter0 ((DFSDM_Filter_TypeDef *) DFSDM1_Filter0_BASE) -#define DFSDM1_Filter1 ((DFSDM_Filter_TypeDef *) DFSDM1_Filter1_BASE) -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOF ((GPIO_TypeDef *) GPIOF_BASE) -#define GPIOG ((GPIO_TypeDef *) GPIOG_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f412rx - * @{ - */ - -#ifndef __STM32F412Rx_H -#define __STM32F412Rx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1 global Interrupts */ - CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */ - CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */ - CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ - CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - USART3_IRQn = 39, /*!< USART3 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */ - TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */ - TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */ - TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare Interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - TIM6_IRQn = 54, /*!< TIM6 global interrupt */ - TIM7_IRQn = 55, /*!< TIM7 global interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - DFSDM1_FLT0_IRQn = 61, /*!< DFSDM1 Filter 0 global Interrupt */ - DFSDM1_FLT1_IRQn = 62, /*!< DFSDM1 Filter 1 global Interrupt */ - CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */ - CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */ - CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */ - CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - RNG_IRQn = 80, /*!< RNG global Interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - SPI4_IRQn = 84, /*!< SPI4 global Interrupt */ - SPI5_IRQn = 85, /*!< SPI5 global Interrupt */ - QUADSPI_IRQn = 92, /*!< QuadSPI global Interrupt */ - FMPI2C1_EV_IRQn = 95, /*!< FMPI2C1 Event Interrupt */ - FMPI2C1_ER_IRQn = 96 /*!< FMPI2C1 Error Interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - -/** - * @brief Controller Area Network TxMailBox - */ - -typedef struct -{ - __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ - __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ - __IO uint32_t TDLR; /*!< CAN mailbox data low register */ - __IO uint32_t TDHR; /*!< CAN mailbox data high register */ -} CAN_TxMailBox_TypeDef; - -/** - * @brief Controller Area Network FIFOMailBox - */ - -typedef struct -{ - __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ - __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ - __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ - __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ -} CAN_FIFOMailBox_TypeDef; - -/** - * @brief Controller Area Network FilterRegister - */ - -typedef struct -{ - __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ - __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ -} CAN_FilterRegister_TypeDef; - -typedef struct -{ - __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ - __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ - __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ - __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ - __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ - __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ - __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ - __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ - uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ - CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ - CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ - uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ - __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ - __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ - uint32_t RESERVED2; /*!< Reserved, 0x208 */ - __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ - uint32_t RESERVED3; /*!< Reserved, 0x210 */ - __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ - uint32_t RESERVED4; /*!< Reserved, 0x218 */ - __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ - uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ - CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ -} CAN_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief DFSDM module registers - */ -typedef struct -{ - __IO uint32_t FLTCR1; /*!< DFSDM control register1, Address offset: 0x100 */ - __IO uint32_t FLTCR2; /*!< DFSDM control register2, Address offset: 0x104 */ - __IO uint32_t FLTISR; /*!< DFSDM interrupt and status register, Address offset: 0x108 */ - __IO uint32_t FLTICR; /*!< DFSDM interrupt flag clear register, Address offset: 0x10C */ - __IO uint32_t FLTJCHGR; /*!< DFSDM injected channel group selection register, Address offset: 0x110 */ - __IO uint32_t FLTFCR; /*!< DFSDM filter control register, Address offset: 0x114 */ - __IO uint32_t FLTJDATAR; /*!< DFSDM data register for injected group, Address offset: 0x118 */ - __IO uint32_t FLTRDATAR; /*!< DFSDM data register for regular group, Address offset: 0x11C */ - __IO uint32_t FLTAWHTR; /*!< DFSDM analog watchdog high threshold register, Address offset: 0x120 */ - __IO uint32_t FLTAWLTR; /*!< DFSDM analog watchdog low threshold register, Address offset: 0x124 */ - __IO uint32_t FLTAWSR; /*!< DFSDM analog watchdog status register Address offset: 0x128 */ - __IO uint32_t FLTAWCFR; /*!< DFSDM analog watchdog clear flag register Address offset: 0x12C */ - __IO uint32_t FLTEXMAX; /*!< DFSDM extreme detector maximum register, Address offset: 0x130 */ - __IO uint32_t FLTEXMIN; /*!< DFSDM extreme detector minimum register Address offset: 0x134 */ - __IO uint32_t FLTCNVTIMR; /*!< DFSDM conversion timer, Address offset: 0x138 */ -} DFSDM_Filter_TypeDef; - -/** - * @brief DFSDM channel configuration registers - */ -typedef struct -{ - __IO uint32_t CHCFGR1; /*!< DFSDM channel configuration register1, Address offset: 0x00 */ - __IO uint32_t CHCFGR2; /*!< DFSDM channel configuration register2, Address offset: 0x04 */ - __IO uint32_t CHAWSCDR; /*!< DFSDM channel analog watchdog and - short circuit detector register, Address offset: 0x08 */ - __IO uint32_t CHWDATAR; /*!< DFSDM channel watchdog filter data register, Address offset: 0x0C */ - __IO uint32_t CHDATINR; /*!< DFSDM channel data input register, Address offset: 0x10 */ -} DFSDM_Channel_TypeDef; - -/** - * @brief Debug MCU - */ -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief Flexible Memory Controller - */ - -typedef struct -{ - __IO uint32_t BTCR[8]; /*!< NOR/PSRAM chip-select control register(BCR) and chip-select timing register(BTR), Address offset: 0x00-1C */ -} FSMC_Bank1_TypeDef; - -/** - * @brief Flexible Memory Controller Bank1E - */ - -typedef struct -{ - __IO uint32_t BWTR[7]; /*!< NOR/PSRAM write timing registers, Address offset: 0x104-0x11C */ -} FSMC_Bank1E_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x24-0x28 */ - __IO uint32_t CFGR; /*!< SYSCFG Configuration register, Address offset: 0x2C */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< FMPI2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< FMPI2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< FMPI2C Own address 1 register, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< FMPI2C Own address 2 register, Address offset: 0x0C */ - __IO uint32_t TIMINGR; /*!< FMPI2C Timing register, Address offset: 0x10 */ - __IO uint32_t TIMEOUTR; /*!< FMPI2C Timeout register, Address offset: 0x14 */ - __IO uint32_t ISR; /*!< FMPI2C Interrupt and status register, Address offset: 0x18 */ - __IO uint32_t ICR; /*!< FMPI2C Interrupt clear register, Address offset: 0x1C */ - __IO uint32_t PECR; /*!< FMPI2C PEC register, Address offset: 0x20 */ - __IO uint32_t RXDR; /*!< FMPI2C Receive data register, Address offset: 0x24 */ - __IO uint32_t TXDR; /*!< FMPI2C Transmit data register, Address offset: 0x28 */ -} FMPI2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - uint32_t RESERVED7; /*!< Reserved, 0x84 */ - __IO uint32_t DCKCFGR; /*!< RCC Dedicated Clocks configuration register, Address offset: 0x8C */ - __IO uint32_t CKGATENR; /*!< RCC Clocks Gated ENable Register, Address offset: 0x90 */ - __IO uint32_t DCKCFGR2; /*!< RCC Dedicated Clocks configuration register 2, Address offset: 0x94 */ -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief QUAD Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR; /*!< QUADSPI Control register, Address offset: 0x00 */ - __IO uint32_t DCR; /*!< QUADSPI Device Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< QUADSPI Status register, Address offset: 0x08 */ - __IO uint32_t FCR; /*!< QUADSPI Flag Clear register, Address offset: 0x0C */ - __IO uint32_t DLR; /*!< QUADSPI Data Length register, Address offset: 0x10 */ - __IO uint32_t CCR; /*!< QUADSPI Communication Configuration register, Address offset: 0x14 */ - __IO uint32_t AR; /*!< QUADSPI Address register, Address offset: 0x18 */ - __IO uint32_t ABR; /*!< QUADSPI Alternate Bytes register, Address offset: 0x1C */ - __IO uint32_t DR; /*!< QUADSPI Data register, Address offset: 0x20 */ - __IO uint32_t PSMKR; /*!< QUADSPI Polling Status Mask register, Address offset: 0x24 */ - __IO uint32_t PSMAR; /*!< QUADSPI Polling Status Match register, Address offset: 0x28 */ - __IO uint32_t PIR; /*!< QUADSPI Polling Interval register, Address offset: 0x2C */ - __IO uint32_t LPTR; /*!< QUADSPI Low Power Timeout register, Address offset: 0x30 */ -} QUADSPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - -/** - * @brief USB_OTG_Core_Registers - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register 000h*/ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register 004h*/ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register 008h*/ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register 00Ch*/ - __IO uint32_t GRSTCTL; /*!< Core Reset Register 010h*/ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register 014h*/ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register 018h*/ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register 01Ch*/ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register 020h*/ - __IO uint32_t GRXFSIZ; /*!< Receive FIFO Size Register 024h*/ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register 028h*/ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg 02Ch*/ - uint32_t Reserved30[2]; /*!< Reserved 030h*/ - __IO uint32_t GCCFG; /*!< General Purpose IO Register 038h*/ - __IO uint32_t CID; /*!< User ID Register 03Ch*/ - uint32_t Reserved5[3]; /*!< Reserved 040h-048h*/ - __IO uint32_t GHWCFG3; /*!< User HW config3 04Ch*/ - uint32_t Reserved6; /*!< Reserved 050h*/ - __IO uint32_t GLPMCFG; /*!< LPM Register 054h*/ - uint32_t Reserved; /*!< Reserved 058h */ - __IO uint32_t GDFIFOCFG; /*!< DFIFO Software Config Register 05Ch */ - uint32_t Reserved43[40]; /*!< Reserved 058h-0FFh */ - __IO uint32_t HPTXFSIZ; /*!< Host Periodic Tx FIFO Size Reg 100h*/ - __IO uint32_t DIEPTXF[0x0F]; /*!< dev Periodic Transmit FIFO */ -} USB_OTG_GlobalTypeDef; - - -/** - * @brief USB_OTG_device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /*!< dev Configuration Register 800h */ - __IO uint32_t DCTL; /*!< dev Control Register 804h */ - __IO uint32_t DSTS; /*!< dev Status Register (RO) 808h */ - uint32_t Reserved0C; /*!< Reserved 80Ch */ - __IO uint32_t DIEPMSK; /*!< dev IN Endpoint Mask 810h */ - __IO uint32_t DOEPMSK; /*!< dev OUT Endpoint Mask 814h */ - __IO uint32_t DAINT; /*!< dev All Endpoints Itr Reg 818h */ - __IO uint32_t DAINTMSK; /*!< dev All Endpoints Itr Mask 81Ch */ - uint32_t Reserved20; /*!< Reserved 820h */ - uint32_t Reserved9; /*!< Reserved 824h */ - __IO uint32_t DVBUSDIS; /*!< dev VBUS discharge Register 828h */ - __IO uint32_t DVBUSPULSE; /*!< dev VBUS Pulse Register 82Ch */ - __IO uint32_t DTHRCTL; /*!< dev threshold 830h */ - __IO uint32_t DIEPEMPMSK; /*!< dev empty msk 834h */ - __IO uint32_t DEACHINT; /*!< dedicated EP interrupt 838h */ - __IO uint32_t DEACHMSK; /*!< dedicated EP msk 83Ch */ - uint32_t Reserved40; /*!< dedicated EP mask 840h */ - __IO uint32_t DINEP1MSK; /*!< dedicated EP mask 844h */ - uint32_t Reserved44[15]; /*!< Reserved 844-87Ch */ - __IO uint32_t DOUTEP1MSK; /*!< dedicated EP msk 884h */ -} USB_OTG_DeviceTypeDef; - - -/** - * @brief USB_OTG_IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /*!< dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /*!< Reserved 900h + (ep_num * 20h) + 04h */ - __IO uint32_t DIEPINT; /*!< dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /*!< Reserved 900h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DIEPTSIZ; /*!< IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h */ - __IO uint32_t DIEPDMA; /*!< IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h */ - __IO uint32_t DTXFSTS; /*!< IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h */ - uint32_t Reserved18; /*!< Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch */ -} USB_OTG_INEndpointTypeDef; - - -/** - * @brief USB_OTG_OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /*!< dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /*!< Reserved B00h + (ep_num * 20h) + 04h */ - __IO uint32_t DOEPINT; /*!< dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /*!< Reserved B00h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DOEPTSIZ; /*!< dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h */ - __IO uint32_t DOEPDMA; /*!< dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h */ - uint32_t Reserved18[2]; /*!< Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch */ -} USB_OTG_OUTEndpointTypeDef; - - -/** - * @brief USB_OTG_Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /*!< Host Configuration Register 400h */ - __IO uint32_t HFIR; /*!< Host Frame Interval Register 404h */ - __IO uint32_t HFNUM; /*!< Host Frame Nbr/Frame Remaining 408h */ - uint32_t Reserved40C; /*!< Reserved 40Ch */ - __IO uint32_t HPTXSTS; /*!< Host Periodic Tx FIFO/ Queue Status 410h */ - __IO uint32_t HAINT; /*!< Host All Channels Interrupt Register 414h */ - __IO uint32_t HAINTMSK; /*!< Host All Channels Interrupt Mask 418h */ -} USB_OTG_HostTypeDef; - - -/** - * @brief USB_OTG_Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; /*!< Host Channel Characteristics Register 500h */ - __IO uint32_t HCSPLT; /*!< Host Channel Split Control Register 504h */ - __IO uint32_t HCINT; /*!< Host Channel Interrupt Register 508h */ - __IO uint32_t HCINTMSK; /*!< Host Channel Interrupt Mask Register 50Ch */ - __IO uint32_t HCTSIZ; /*!< Host Channel Transfer Size Register 510h */ - __IO uint32_t HCDMA; /*!< Host Channel DMA Address Register 514h */ - uint32_t Reserved[2]; /*!< Reserved */ -} USB_OTG_HostChannelTypeDef; - - -/** - * @brief Peripheral_memory_map - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(256 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define FSMC_R_BASE 0xA0000000U /*!< FSMC registers base address */ -#define QSPI_R_BASE 0xA0001000U /*!< QuadSPI registers base address */ - -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(256 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define FLASH_END 0x080FFFFFU /*!< FLASH end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define TIM7_BASE (APB1PERIPH_BASE + 0x1400U) -#define TIM12_BASE (APB1PERIPH_BASE + 0x1800U) -#define TIM13_BASE (APB1PERIPH_BASE + 0x1C00U) -#define TIM14_BASE (APB1PERIPH_BASE + 0x2000U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define USART3_BASE (APB1PERIPH_BASE + 0x4800U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define FMPI2C1_BASE (APB1PERIPH_BASE + 0x6000U) -#define CAN1_BASE (APB1PERIPH_BASE + 0x6400U) -#define CAN2_BASE (APB1PERIPH_BASE + 0x6800U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define TIM8_BASE (APB2PERIPH_BASE + 0x0400U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SPI4_BASE (APB2PERIPH_BASE + 0x3400U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) -#define SPI5_BASE (APB2PERIPH_BASE + 0x5000U) -#define DFSDM1_BASE (APB2PERIPH_BASE + 0x6000U) -#define DFSDM1_Channel0_BASE (DFSDM1_BASE + 0x00U) -#define DFSDM1_Channel1_BASE (DFSDM1_BASE + 0x20U) -#define DFSDM1_Channel2_BASE (DFSDM1_BASE + 0x40U) -#define DFSDM1_Channel3_BASE (DFSDM1_BASE + 0x60U) -#define DFSDM1_Filter0_BASE (DFSDM1_BASE + 0x100U) -#define DFSDM1_Filter1_BASE (DFSDM1_BASE + 0x180U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOF_BASE (AHB1PERIPH_BASE + 0x1400U) -#define GPIOG_BASE (AHB1PERIPH_BASE + 0x1800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) - -/*!< AHB2 peripherals */ -#define RNG_BASE (AHB2PERIPH_BASE + 0x60800U) - -/*!< FSMC Bankx registers base address */ -#define FSMC_Bank1_R_BASE (FSMC_R_BASE + 0x0000U) -#define FSMC_Bank1E_R_BASE (FSMC_R_BASE + 0x0104U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define TIM7 ((TIM_TypeDef *) TIM7_BASE) -#define TIM12 ((TIM_TypeDef *) TIM12_BASE) -#define TIM13 ((TIM_TypeDef *) TIM13_BASE) -#define TIM14 ((TIM_TypeDef *) TIM14_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define USART3 ((USART_TypeDef *) USART3_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define FMPI2C1 ((FMPI2C_TypeDef *) FMPI2C1_BASE) -#define CAN1 ((CAN_TypeDef *) CAN1_BASE) -#define CAN2 ((CAN_TypeDef *) CAN2_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define TIM8 ((TIM_TypeDef *) TIM8_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SPI4 ((SPI_TypeDef *) SPI4_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define SPI5 ((SPI_TypeDef *) SPI5_BASE) -#define DFSDM1_Channel0 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel0_BASE) -#define DFSDM1_Channel1 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel1_BASE) -#define DFSDM1_Channel2 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel2_BASE) -#define DFSDM1_Channel3 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel3_BASE) -#define DFSDM1_Filter0 ((DFSDM_Filter_TypeDef *) DFSDM1_Filter0_BASE) -#define DFSDM1_Filter1 ((DFSDM_Filter_TypeDef *) DFSDM1_Filter1_BASE) -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOF ((GPIO_TypeDef *) GPIOF_BASE) -#define GPIOG ((GPIO_TypeDef *) GPIOG_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) -#define FSMC_Bank1 ((FSMC_Bank1_TypeDef *) FSMC_Bank1_R_BASE) -#define FSMC_Bank1E ((FSMC_Bank1E_TypeDef *) FSMC_Bank1E_R_BASE) -#define QUADSPI ((QUADSPI_TypeDef *) QSPI_R_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f412vx - * @{ - */ - -#ifndef __STM32F412Vx_H -#define __STM32F412Vx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1 global Interrupts */ - CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */ - CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */ - CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ - CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - USART3_IRQn = 39, /*!< USART3 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */ - TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */ - TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */ - TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare Interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - TIM6_IRQn = 54, /*!< TIM6 global interrupt */ - TIM7_IRQn = 55, /*!< TIM7 global interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - DFSDM1_FLT0_IRQn = 61, /*!< DFSDM1 Filter 0 global Interrupt */ - DFSDM1_FLT1_IRQn = 62, /*!< DFSDM1 Filter 1 global Interrupt */ - CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */ - CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */ - CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */ - CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - RNG_IRQn = 80, /*!< RNG global Interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - SPI4_IRQn = 84, /*!< SPI4 global Interrupt */ - SPI5_IRQn = 85, /*!< SPI5 global Interrupt */ - QUADSPI_IRQn = 92, /*!< QuadSPI global Interrupt */ - FMPI2C1_EV_IRQn = 95, /*!< FMPI2C1 Event Interrupt */ - FMPI2C1_ER_IRQn = 96 /*!< FMPI2C1 Error Interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - -/** - * @brief Controller Area Network TxMailBox - */ - -typedef struct -{ - __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ - __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ - __IO uint32_t TDLR; /*!< CAN mailbox data low register */ - __IO uint32_t TDHR; /*!< CAN mailbox data high register */ -} CAN_TxMailBox_TypeDef; - -/** - * @brief Controller Area Network FIFOMailBox - */ - -typedef struct -{ - __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ - __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ - __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ - __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ -} CAN_FIFOMailBox_TypeDef; - -/** - * @brief Controller Area Network FilterRegister - */ - -typedef struct -{ - __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ - __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ -} CAN_FilterRegister_TypeDef; - -typedef struct -{ - __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ - __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ - __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ - __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ - __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ - __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ - __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ - __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ - uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ - CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ - CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ - uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ - __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ - __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ - uint32_t RESERVED2; /*!< Reserved, 0x208 */ - __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ - uint32_t RESERVED3; /*!< Reserved, 0x210 */ - __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ - uint32_t RESERVED4; /*!< Reserved, 0x218 */ - __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ - uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ - CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ -} CAN_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief DFSDM module registers - */ -typedef struct -{ - __IO uint32_t FLTCR1; /*!< DFSDM control register1, Address offset: 0x100 */ - __IO uint32_t FLTCR2; /*!< DFSDM control register2, Address offset: 0x104 */ - __IO uint32_t FLTISR; /*!< DFSDM interrupt and status register, Address offset: 0x108 */ - __IO uint32_t FLTICR; /*!< DFSDM interrupt flag clear register, Address offset: 0x10C */ - __IO uint32_t FLTJCHGR; /*!< DFSDM injected channel group selection register, Address offset: 0x110 */ - __IO uint32_t FLTFCR; /*!< DFSDM filter control register, Address offset: 0x114 */ - __IO uint32_t FLTJDATAR; /*!< DFSDM data register for injected group, Address offset: 0x118 */ - __IO uint32_t FLTRDATAR; /*!< DFSDM data register for regular group, Address offset: 0x11C */ - __IO uint32_t FLTAWHTR; /*!< DFSDM analog watchdog high threshold register, Address offset: 0x120 */ - __IO uint32_t FLTAWLTR; /*!< DFSDM analog watchdog low threshold register, Address offset: 0x124 */ - __IO uint32_t FLTAWSR; /*!< DFSDM analog watchdog status register Address offset: 0x128 */ - __IO uint32_t FLTAWCFR; /*!< DFSDM analog watchdog clear flag register Address offset: 0x12C */ - __IO uint32_t FLTEXMAX; /*!< DFSDM extreme detector maximum register, Address offset: 0x130 */ - __IO uint32_t FLTEXMIN; /*!< DFSDM extreme detector minimum register Address offset: 0x134 */ - __IO uint32_t FLTCNVTIMR; /*!< DFSDM conversion timer, Address offset: 0x138 */ -} DFSDM_Filter_TypeDef; - -/** - * @brief DFSDM channel configuration registers - */ -typedef struct -{ - __IO uint32_t CHCFGR1; /*!< DFSDM channel configuration register1, Address offset: 0x00 */ - __IO uint32_t CHCFGR2; /*!< DFSDM channel configuration register2, Address offset: 0x04 */ - __IO uint32_t CHAWSCDR; /*!< DFSDM channel analog watchdog and - short circuit detector register, Address offset: 0x08 */ - __IO uint32_t CHWDATAR; /*!< DFSDM channel watchdog filter data register, Address offset: 0x0C */ - __IO uint32_t CHDATINR; /*!< DFSDM channel data input register, Address offset: 0x10 */ -} DFSDM_Channel_TypeDef; - -/** - * @brief Debug MCU - */ -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief Flexible Memory Controller - */ - -typedef struct -{ - __IO uint32_t BTCR[8]; /*!< NOR/PSRAM chip-select control register(BCR) and chip-select timing register(BTR), Address offset: 0x00-1C */ -} FSMC_Bank1_TypeDef; - -/** - * @brief Flexible Memory Controller Bank1E - */ - -typedef struct -{ - __IO uint32_t BWTR[7]; /*!< NOR/PSRAM write timing registers, Address offset: 0x104-0x11C */ -} FSMC_Bank1E_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x24-0x28 */ - __IO uint32_t CFGR; /*!< SYSCFG Configuration register, Address offset: 0x2C */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< FMPI2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< FMPI2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< FMPI2C Own address 1 register, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< FMPI2C Own address 2 register, Address offset: 0x0C */ - __IO uint32_t TIMINGR; /*!< FMPI2C Timing register, Address offset: 0x10 */ - __IO uint32_t TIMEOUTR; /*!< FMPI2C Timeout register, Address offset: 0x14 */ - __IO uint32_t ISR; /*!< FMPI2C Interrupt and status register, Address offset: 0x18 */ - __IO uint32_t ICR; /*!< FMPI2C Interrupt clear register, Address offset: 0x1C */ - __IO uint32_t PECR; /*!< FMPI2C PEC register, Address offset: 0x20 */ - __IO uint32_t RXDR; /*!< FMPI2C Receive data register, Address offset: 0x24 */ - __IO uint32_t TXDR; /*!< FMPI2C Transmit data register, Address offset: 0x28 */ -} FMPI2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - uint32_t RESERVED7; /*!< Reserved, 0x84 */ - __IO uint32_t DCKCFGR; /*!< RCC Dedicated Clocks configuration register, Address offset: 0x8C */ - __IO uint32_t CKGATENR; /*!< RCC Clocks Gated ENable Register, Address offset: 0x90 */ - __IO uint32_t DCKCFGR2; /*!< RCC Dedicated Clocks configuration register 2, Address offset: 0x94 */ -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief QUAD Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR; /*!< QUADSPI Control register, Address offset: 0x00 */ - __IO uint32_t DCR; /*!< QUADSPI Device Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< QUADSPI Status register, Address offset: 0x08 */ - __IO uint32_t FCR; /*!< QUADSPI Flag Clear register, Address offset: 0x0C */ - __IO uint32_t DLR; /*!< QUADSPI Data Length register, Address offset: 0x10 */ - __IO uint32_t CCR; /*!< QUADSPI Communication Configuration register, Address offset: 0x14 */ - __IO uint32_t AR; /*!< QUADSPI Address register, Address offset: 0x18 */ - __IO uint32_t ABR; /*!< QUADSPI Alternate Bytes register, Address offset: 0x1C */ - __IO uint32_t DR; /*!< QUADSPI Data register, Address offset: 0x20 */ - __IO uint32_t PSMKR; /*!< QUADSPI Polling Status Mask register, Address offset: 0x24 */ - __IO uint32_t PSMAR; /*!< QUADSPI Polling Status Match register, Address offset: 0x28 */ - __IO uint32_t PIR; /*!< QUADSPI Polling Interval register, Address offset: 0x2C */ - __IO uint32_t LPTR; /*!< QUADSPI Low Power Timeout register, Address offset: 0x30 */ -} QUADSPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - -/** - * @brief USB_OTG_Core_Registers - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register 000h*/ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register 004h*/ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register 008h*/ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register 00Ch*/ - __IO uint32_t GRSTCTL; /*!< Core Reset Register 010h*/ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register 014h*/ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register 018h*/ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register 01Ch*/ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register 020h*/ - __IO uint32_t GRXFSIZ; /*!< Receive FIFO Size Register 024h*/ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register 028h*/ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg 02Ch*/ - uint32_t Reserved30[2]; /*!< Reserved 030h*/ - __IO uint32_t GCCFG; /*!< General Purpose IO Register 038h*/ - __IO uint32_t CID; /*!< User ID Register 03Ch*/ - uint32_t Reserved5[3]; /*!< Reserved 040h-048h*/ - __IO uint32_t GHWCFG3; /*!< User HW config3 04Ch*/ - uint32_t Reserved6; /*!< Reserved 050h*/ - __IO uint32_t GLPMCFG; /*!< LPM Register 054h*/ - uint32_t Reserved; /*!< Reserved 058h */ - __IO uint32_t GDFIFOCFG; /*!< DFIFO Software Config Register 05Ch */ - uint32_t Reserved43[40]; /*!< Reserved 058h-0FFh */ - __IO uint32_t HPTXFSIZ; /*!< Host Periodic Tx FIFO Size Reg 100h*/ - __IO uint32_t DIEPTXF[0x0F]; /*!< dev Periodic Transmit FIFO */ -} USB_OTG_GlobalTypeDef; - - -/** - * @brief USB_OTG_device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /*!< dev Configuration Register 800h */ - __IO uint32_t DCTL; /*!< dev Control Register 804h */ - __IO uint32_t DSTS; /*!< dev Status Register (RO) 808h */ - uint32_t Reserved0C; /*!< Reserved 80Ch */ - __IO uint32_t DIEPMSK; /*!< dev IN Endpoint Mask 810h */ - __IO uint32_t DOEPMSK; /*!< dev OUT Endpoint Mask 814h */ - __IO uint32_t DAINT; /*!< dev All Endpoints Itr Reg 818h */ - __IO uint32_t DAINTMSK; /*!< dev All Endpoints Itr Mask 81Ch */ - uint32_t Reserved20; /*!< Reserved 820h */ - uint32_t Reserved9; /*!< Reserved 824h */ - __IO uint32_t DVBUSDIS; /*!< dev VBUS discharge Register 828h */ - __IO uint32_t DVBUSPULSE; /*!< dev VBUS Pulse Register 82Ch */ - __IO uint32_t DTHRCTL; /*!< dev threshold 830h */ - __IO uint32_t DIEPEMPMSK; /*!< dev empty msk 834h */ - __IO uint32_t DEACHINT; /*!< dedicated EP interrupt 838h */ - __IO uint32_t DEACHMSK; /*!< dedicated EP msk 83Ch */ - uint32_t Reserved40; /*!< dedicated EP mask 840h */ - __IO uint32_t DINEP1MSK; /*!< dedicated EP mask 844h */ - uint32_t Reserved44[15]; /*!< Reserved 844-87Ch */ - __IO uint32_t DOUTEP1MSK; /*!< dedicated EP msk 884h */ -} USB_OTG_DeviceTypeDef; - - -/** - * @brief USB_OTG_IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /*!< dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /*!< Reserved 900h + (ep_num * 20h) + 04h */ - __IO uint32_t DIEPINT; /*!< dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /*!< Reserved 900h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DIEPTSIZ; /*!< IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h */ - __IO uint32_t DIEPDMA; /*!< IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h */ - __IO uint32_t DTXFSTS; /*!< IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h */ - uint32_t Reserved18; /*!< Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch */ -} USB_OTG_INEndpointTypeDef; - - -/** - * @brief USB_OTG_OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /*!< dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /*!< Reserved B00h + (ep_num * 20h) + 04h */ - __IO uint32_t DOEPINT; /*!< dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /*!< Reserved B00h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DOEPTSIZ; /*!< dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h */ - __IO uint32_t DOEPDMA; /*!< dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h */ - uint32_t Reserved18[2]; /*!< Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch */ -} USB_OTG_OUTEndpointTypeDef; - - -/** - * @brief USB_OTG_Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /*!< Host Configuration Register 400h */ - __IO uint32_t HFIR; /*!< Host Frame Interval Register 404h */ - __IO uint32_t HFNUM; /*!< Host Frame Nbr/Frame Remaining 408h */ - uint32_t Reserved40C; /*!< Reserved 40Ch */ - __IO uint32_t HPTXSTS; /*!< Host Periodic Tx FIFO/ Queue Status 410h */ - __IO uint32_t HAINT; /*!< Host All Channels Interrupt Register 414h */ - __IO uint32_t HAINTMSK; /*!< Host All Channels Interrupt Mask 418h */ -} USB_OTG_HostTypeDef; - - -/** - * @brief USB_OTG_Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; /*!< Host Channel Characteristics Register 500h */ - __IO uint32_t HCSPLT; /*!< Host Channel Split Control Register 504h */ - __IO uint32_t HCINT; /*!< Host Channel Interrupt Register 508h */ - __IO uint32_t HCINTMSK; /*!< Host Channel Interrupt Mask Register 50Ch */ - __IO uint32_t HCTSIZ; /*!< Host Channel Transfer Size Register 510h */ - __IO uint32_t HCDMA; /*!< Host Channel DMA Address Register 514h */ - uint32_t Reserved[2]; /*!< Reserved */ -} USB_OTG_HostChannelTypeDef; - - -/** - * @brief Peripheral_memory_map - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(256 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define FSMC_R_BASE 0xA0000000U /*!< FSMC registers base address */ -#define QSPI_R_BASE 0xA0001000U /*!< QuadSPI registers base address */ - -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(256 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define FLASH_END 0x080FFFFFU /*!< FLASH end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define TIM7_BASE (APB1PERIPH_BASE + 0x1400U) -#define TIM12_BASE (APB1PERIPH_BASE + 0x1800U) -#define TIM13_BASE (APB1PERIPH_BASE + 0x1C00U) -#define TIM14_BASE (APB1PERIPH_BASE + 0x2000U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define USART3_BASE (APB1PERIPH_BASE + 0x4800U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define FMPI2C1_BASE (APB1PERIPH_BASE + 0x6000U) -#define CAN1_BASE (APB1PERIPH_BASE + 0x6400U) -#define CAN2_BASE (APB1PERIPH_BASE + 0x6800U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define TIM8_BASE (APB2PERIPH_BASE + 0x0400U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SPI4_BASE (APB2PERIPH_BASE + 0x3400U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) -#define SPI5_BASE (APB2PERIPH_BASE + 0x5000U) -#define DFSDM1_BASE (APB2PERIPH_BASE + 0x6000U) -#define DFSDM1_Channel0_BASE (DFSDM1_BASE + 0x00U) -#define DFSDM1_Channel1_BASE (DFSDM1_BASE + 0x20U) -#define DFSDM1_Channel2_BASE (DFSDM1_BASE + 0x40U) -#define DFSDM1_Channel3_BASE (DFSDM1_BASE + 0x60U) -#define DFSDM1_Filter0_BASE (DFSDM1_BASE + 0x100U) -#define DFSDM1_Filter1_BASE (DFSDM1_BASE + 0x180U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOF_BASE (AHB1PERIPH_BASE + 0x1400U) -#define GPIOG_BASE (AHB1PERIPH_BASE + 0x1800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) - -/*!< AHB2 peripherals */ -#define RNG_BASE (AHB2PERIPH_BASE + 0x60800U) - -/*!< FSMC Bankx registers base address */ -#define FSMC_Bank1_R_BASE (FSMC_R_BASE + 0x0000U) -#define FSMC_Bank1E_R_BASE (FSMC_R_BASE + 0x0104U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define TIM7 ((TIM_TypeDef *) TIM7_BASE) -#define TIM12 ((TIM_TypeDef *) TIM12_BASE) -#define TIM13 ((TIM_TypeDef *) TIM13_BASE) -#define TIM14 ((TIM_TypeDef *) TIM14_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define USART3 ((USART_TypeDef *) USART3_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define FMPI2C1 ((FMPI2C_TypeDef *) FMPI2C1_BASE) -#define CAN1 ((CAN_TypeDef *) CAN1_BASE) -#define CAN2 ((CAN_TypeDef *) CAN2_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define TIM8 ((TIM_TypeDef *) TIM8_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SPI4 ((SPI_TypeDef *) SPI4_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define SPI5 ((SPI_TypeDef *) SPI5_BASE) -#define DFSDM1_Channel0 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel0_BASE) -#define DFSDM1_Channel1 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel1_BASE) -#define DFSDM1_Channel2 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel2_BASE) -#define DFSDM1_Channel3 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel3_BASE) -#define DFSDM1_Filter0 ((DFSDM_Filter_TypeDef *) DFSDM1_Filter0_BASE) -#define DFSDM1_Filter1 ((DFSDM_Filter_TypeDef *) DFSDM1_Filter1_BASE) -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOF ((GPIO_TypeDef *) GPIOF_BASE) -#define GPIOG ((GPIO_TypeDef *) GPIOG_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) -#define FSMC_Bank1 ((FSMC_Bank1_TypeDef *) FSMC_Bank1_R_BASE) -#define FSMC_Bank1E ((FSMC_Bank1E_TypeDef *) FSMC_Bank1E_R_BASE) -#define QUADSPI ((QUADSPI_TypeDef *) QSPI_R_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f412zx - * @{ - */ - -#ifndef __STM32F412Zx_H -#define __STM32F412Zx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1 global Interrupts */ - CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */ - CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */ - CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ - CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - USART3_IRQn = 39, /*!< USART3 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */ - TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */ - TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */ - TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare Interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - TIM6_IRQn = 54, /*!< TIM6 global interrupt */ - TIM7_IRQn = 55, /*!< TIM7 global interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - DFSDM1_FLT0_IRQn = 61, /*!< DFSDM1 Filter 0 global Interrupt */ - DFSDM1_FLT1_IRQn = 62, /*!< DFSDM1 Filter 1 global Interrupt */ - CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */ - CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */ - CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */ - CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - RNG_IRQn = 80, /*!< RNG global Interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - SPI4_IRQn = 84, /*!< SPI4 global Interrupt */ - SPI5_IRQn = 85, /*!< SPI5 global Interrupt */ - QUADSPI_IRQn = 92, /*!< QuadSPI global Interrupt */ - FMPI2C1_EV_IRQn = 95, /*!< FMPI2C1 Event Interrupt */ - FMPI2C1_ER_IRQn = 96 /*!< FMPI2C1 Error Interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - -/** - * @brief Controller Area Network TxMailBox - */ - -typedef struct -{ - __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ - __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ - __IO uint32_t TDLR; /*!< CAN mailbox data low register */ - __IO uint32_t TDHR; /*!< CAN mailbox data high register */ -} CAN_TxMailBox_TypeDef; - -/** - * @brief Controller Area Network FIFOMailBox - */ - -typedef struct -{ - __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ - __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ - __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ - __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ -} CAN_FIFOMailBox_TypeDef; - -/** - * @brief Controller Area Network FilterRegister - */ - -typedef struct -{ - __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ - __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ -} CAN_FilterRegister_TypeDef; - -typedef struct -{ - __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ - __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ - __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ - __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ - __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ - __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ - __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ - __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ - uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ - CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ - CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ - uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ - __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ - __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ - uint32_t RESERVED2; /*!< Reserved, 0x208 */ - __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ - uint32_t RESERVED3; /*!< Reserved, 0x210 */ - __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ - uint32_t RESERVED4; /*!< Reserved, 0x218 */ - __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ - uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ - CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ -} CAN_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief DFSDM module registers - */ -typedef struct -{ - __IO uint32_t FLTCR1; /*!< DFSDM control register1, Address offset: 0x100 */ - __IO uint32_t FLTCR2; /*!< DFSDM control register2, Address offset: 0x104 */ - __IO uint32_t FLTISR; /*!< DFSDM interrupt and status register, Address offset: 0x108 */ - __IO uint32_t FLTICR; /*!< DFSDM interrupt flag clear register, Address offset: 0x10C */ - __IO uint32_t FLTJCHGR; /*!< DFSDM injected channel group selection register, Address offset: 0x110 */ - __IO uint32_t FLTFCR; /*!< DFSDM filter control register, Address offset: 0x114 */ - __IO uint32_t FLTJDATAR; /*!< DFSDM data register for injected group, Address offset: 0x118 */ - __IO uint32_t FLTRDATAR; /*!< DFSDM data register for regular group, Address offset: 0x11C */ - __IO uint32_t FLTAWHTR; /*!< DFSDM analog watchdog high threshold register, Address offset: 0x120 */ - __IO uint32_t FLTAWLTR; /*!< DFSDM analog watchdog low threshold register, Address offset: 0x124 */ - __IO uint32_t FLTAWSR; /*!< DFSDM analog watchdog status register Address offset: 0x128 */ - __IO uint32_t FLTAWCFR; /*!< DFSDM analog watchdog clear flag register Address offset: 0x12C */ - __IO uint32_t FLTEXMAX; /*!< DFSDM extreme detector maximum register, Address offset: 0x130 */ - __IO uint32_t FLTEXMIN; /*!< DFSDM extreme detector minimum register Address offset: 0x134 */ - __IO uint32_t FLTCNVTIMR; /*!< DFSDM conversion timer, Address offset: 0x138 */ -} DFSDM_Filter_TypeDef; - -/** - * @brief DFSDM channel configuration registers - */ -typedef struct -{ - __IO uint32_t CHCFGR1; /*!< DFSDM channel configuration register1, Address offset: 0x00 */ - __IO uint32_t CHCFGR2; /*!< DFSDM channel configuration register2, Address offset: 0x04 */ - __IO uint32_t CHAWSCDR; /*!< DFSDM channel analog watchdog and - short circuit detector register, Address offset: 0x08 */ - __IO uint32_t CHWDATAR; /*!< DFSDM channel watchdog filter data register, Address offset: 0x0C */ - __IO uint32_t CHDATINR; /*!< DFSDM channel data input register, Address offset: 0x10 */ -} DFSDM_Channel_TypeDef; - -/** - * @brief Debug MCU - */ -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief Flexible Memory Controller - */ - -typedef struct -{ - __IO uint32_t BTCR[8]; /*!< NOR/PSRAM chip-select control register(BCR) and chip-select timing register(BTR), Address offset: 0x00-1C */ -} FSMC_Bank1_TypeDef; - -/** - * @brief Flexible Memory Controller Bank1E - */ - -typedef struct -{ - __IO uint32_t BWTR[7]; /*!< NOR/PSRAM write timing registers, Address offset: 0x104-0x11C */ -} FSMC_Bank1E_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x24-0x28 */ - __IO uint32_t CFGR; /*!< SYSCFG Configuration register, Address offset: 0x2C */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< FMPI2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< FMPI2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< FMPI2C Own address 1 register, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< FMPI2C Own address 2 register, Address offset: 0x0C */ - __IO uint32_t TIMINGR; /*!< FMPI2C Timing register, Address offset: 0x10 */ - __IO uint32_t TIMEOUTR; /*!< FMPI2C Timeout register, Address offset: 0x14 */ - __IO uint32_t ISR; /*!< FMPI2C Interrupt and status register, Address offset: 0x18 */ - __IO uint32_t ICR; /*!< FMPI2C Interrupt clear register, Address offset: 0x1C */ - __IO uint32_t PECR; /*!< FMPI2C PEC register, Address offset: 0x20 */ - __IO uint32_t RXDR; /*!< FMPI2C Receive data register, Address offset: 0x24 */ - __IO uint32_t TXDR; /*!< FMPI2C Transmit data register, Address offset: 0x28 */ -} FMPI2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - uint32_t RESERVED7; /*!< Reserved, 0x84 */ - __IO uint32_t DCKCFGR; /*!< RCC Dedicated Clocks configuration register, Address offset: 0x8C */ - __IO uint32_t CKGATENR; /*!< RCC Clocks Gated ENable Register, Address offset: 0x90 */ - __IO uint32_t DCKCFGR2; /*!< RCC Dedicated Clocks configuration register 2, Address offset: 0x94 */ -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief QUAD Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR; /*!< QUADSPI Control register, Address offset: 0x00 */ - __IO uint32_t DCR; /*!< QUADSPI Device Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< QUADSPI Status register, Address offset: 0x08 */ - __IO uint32_t FCR; /*!< QUADSPI Flag Clear register, Address offset: 0x0C */ - __IO uint32_t DLR; /*!< QUADSPI Data Length register, Address offset: 0x10 */ - __IO uint32_t CCR; /*!< QUADSPI Communication Configuration register, Address offset: 0x14 */ - __IO uint32_t AR; /*!< QUADSPI Address register, Address offset: 0x18 */ - __IO uint32_t ABR; /*!< QUADSPI Alternate Bytes register, Address offset: 0x1C */ - __IO uint32_t DR; /*!< QUADSPI Data register, Address offset: 0x20 */ - __IO uint32_t PSMKR; /*!< QUADSPI Polling Status Mask register, Address offset: 0x24 */ - __IO uint32_t PSMAR; /*!< QUADSPI Polling Status Match register, Address offset: 0x28 */ - __IO uint32_t PIR; /*!< QUADSPI Polling Interval register, Address offset: 0x2C */ - __IO uint32_t LPTR; /*!< QUADSPI Low Power Timeout register, Address offset: 0x30 */ -} QUADSPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - -/** - * @brief USB_OTG_Core_Registers - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register 000h*/ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register 004h*/ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register 008h*/ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register 00Ch*/ - __IO uint32_t GRSTCTL; /*!< Core Reset Register 010h*/ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register 014h*/ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register 018h*/ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register 01Ch*/ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register 020h*/ - __IO uint32_t GRXFSIZ; /*!< Receive FIFO Size Register 024h*/ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register 028h*/ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg 02Ch*/ - uint32_t Reserved30[2]; /*!< Reserved 030h*/ - __IO uint32_t GCCFG; /*!< General Purpose IO Register 038h*/ - __IO uint32_t CID; /*!< User ID Register 03Ch*/ - uint32_t Reserved5[3]; /*!< Reserved 040h-048h*/ - __IO uint32_t GHWCFG3; /*!< User HW config3 04Ch*/ - uint32_t Reserved6; /*!< Reserved 050h*/ - __IO uint32_t GLPMCFG; /*!< LPM Register 054h*/ - uint32_t Reserved; /*!< Reserved 058h */ - __IO uint32_t GDFIFOCFG; /*!< DFIFO Software Config Register 05Ch */ - uint32_t Reserved43[40]; /*!< Reserved 058h-0FFh */ - __IO uint32_t HPTXFSIZ; /*!< Host Periodic Tx FIFO Size Reg 100h*/ - __IO uint32_t DIEPTXF[0x0F]; /*!< dev Periodic Transmit FIFO */ -} USB_OTG_GlobalTypeDef; - - -/** - * @brief USB_OTG_device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /*!< dev Configuration Register 800h */ - __IO uint32_t DCTL; /*!< dev Control Register 804h */ - __IO uint32_t DSTS; /*!< dev Status Register (RO) 808h */ - uint32_t Reserved0C; /*!< Reserved 80Ch */ - __IO uint32_t DIEPMSK; /*!< dev IN Endpoint Mask 810h */ - __IO uint32_t DOEPMSK; /*!< dev OUT Endpoint Mask 814h */ - __IO uint32_t DAINT; /*!< dev All Endpoints Itr Reg 818h */ - __IO uint32_t DAINTMSK; /*!< dev All Endpoints Itr Mask 81Ch */ - uint32_t Reserved20; /*!< Reserved 820h */ - uint32_t Reserved9; /*!< Reserved 824h */ - __IO uint32_t DVBUSDIS; /*!< dev VBUS discharge Register 828h */ - __IO uint32_t DVBUSPULSE; /*!< dev VBUS Pulse Register 82Ch */ - __IO uint32_t DTHRCTL; /*!< dev threshold 830h */ - __IO uint32_t DIEPEMPMSK; /*!< dev empty msk 834h */ - __IO uint32_t DEACHINT; /*!< dedicated EP interrupt 838h */ - __IO uint32_t DEACHMSK; /*!< dedicated EP msk 83Ch */ - uint32_t Reserved40; /*!< dedicated EP mask 840h */ - __IO uint32_t DINEP1MSK; /*!< dedicated EP mask 844h */ - uint32_t Reserved44[15]; /*!< Reserved 844-87Ch */ - __IO uint32_t DOUTEP1MSK; /*!< dedicated EP msk 884h */ -} USB_OTG_DeviceTypeDef; - - -/** - * @brief USB_OTG_IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /*!< dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /*!< Reserved 900h + (ep_num * 20h) + 04h */ - __IO uint32_t DIEPINT; /*!< dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /*!< Reserved 900h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DIEPTSIZ; /*!< IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h */ - __IO uint32_t DIEPDMA; /*!< IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h */ - __IO uint32_t DTXFSTS; /*!< IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h */ - uint32_t Reserved18; /*!< Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch */ -} USB_OTG_INEndpointTypeDef; - - -/** - * @brief USB_OTG_OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /*!< dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /*!< Reserved B00h + (ep_num * 20h) + 04h */ - __IO uint32_t DOEPINT; /*!< dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /*!< Reserved B00h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DOEPTSIZ; /*!< dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h */ - __IO uint32_t DOEPDMA; /*!< dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h */ - uint32_t Reserved18[2]; /*!< Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch */ -} USB_OTG_OUTEndpointTypeDef; - - -/** - * @brief USB_OTG_Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /*!< Host Configuration Register 400h */ - __IO uint32_t HFIR; /*!< Host Frame Interval Register 404h */ - __IO uint32_t HFNUM; /*!< Host Frame Nbr/Frame Remaining 408h */ - uint32_t Reserved40C; /*!< Reserved 40Ch */ - __IO uint32_t HPTXSTS; /*!< Host Periodic Tx FIFO/ Queue Status 410h */ - __IO uint32_t HAINT; /*!< Host All Channels Interrupt Register 414h */ - __IO uint32_t HAINTMSK; /*!< Host All Channels Interrupt Mask 418h */ -} USB_OTG_HostTypeDef; - - -/** - * @brief USB_OTG_Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; /*!< Host Channel Characteristics Register 500h */ - __IO uint32_t HCSPLT; /*!< Host Channel Split Control Register 504h */ - __IO uint32_t HCINT; /*!< Host Channel Interrupt Register 508h */ - __IO uint32_t HCINTMSK; /*!< Host Channel Interrupt Mask Register 50Ch */ - __IO uint32_t HCTSIZ; /*!< Host Channel Transfer Size Register 510h */ - __IO uint32_t HCDMA; /*!< Host Channel DMA Address Register 514h */ - uint32_t Reserved[2]; /*!< Reserved */ -} USB_OTG_HostChannelTypeDef; - - -/** - * @brief Peripheral_memory_map - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(256 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define FSMC_R_BASE 0xA0000000U /*!< FSMC registers base address */ -#define QSPI_R_BASE 0xA0001000U /*!< QuadSPI registers base address */ - -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(256 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define FLASH_END 0x080FFFFFU /*!< FLASH end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define TIM7_BASE (APB1PERIPH_BASE + 0x1400U) -#define TIM12_BASE (APB1PERIPH_BASE + 0x1800U) -#define TIM13_BASE (APB1PERIPH_BASE + 0x1C00U) -#define TIM14_BASE (APB1PERIPH_BASE + 0x2000U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define USART3_BASE (APB1PERIPH_BASE + 0x4800U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define FMPI2C1_BASE (APB1PERIPH_BASE + 0x6000U) -#define CAN1_BASE (APB1PERIPH_BASE + 0x6400U) -#define CAN2_BASE (APB1PERIPH_BASE + 0x6800U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define TIM8_BASE (APB2PERIPH_BASE + 0x0400U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SPI4_BASE (APB2PERIPH_BASE + 0x3400U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) -#define SPI5_BASE (APB2PERIPH_BASE + 0x5000U) -#define DFSDM1_BASE (APB2PERIPH_BASE + 0x6000U) -#define DFSDM1_Channel0_BASE (DFSDM1_BASE + 0x00U) -#define DFSDM1_Channel1_BASE (DFSDM1_BASE + 0x20U) -#define DFSDM1_Channel2_BASE (DFSDM1_BASE + 0x40U) -#define DFSDM1_Channel3_BASE (DFSDM1_BASE + 0x60U) -#define DFSDM1_Filter0_BASE (DFSDM1_BASE + 0x100U) -#define DFSDM1_Filter1_BASE (DFSDM1_BASE + 0x180U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOF_BASE (AHB1PERIPH_BASE + 0x1400U) -#define GPIOG_BASE (AHB1PERIPH_BASE + 0x1800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) - -/*!< AHB2 peripherals */ -#define RNG_BASE (AHB2PERIPH_BASE + 0x60800U) - -/*!< FSMC Bankx registers base address */ -#define FSMC_Bank1_R_BASE (FSMC_R_BASE + 0x0000U) -#define FSMC_Bank1E_R_BASE (FSMC_R_BASE + 0x0104U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define TIM7 ((TIM_TypeDef *) TIM7_BASE) -#define TIM12 ((TIM_TypeDef *) TIM12_BASE) -#define TIM13 ((TIM_TypeDef *) TIM13_BASE) -#define TIM14 ((TIM_TypeDef *) TIM14_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define USART3 ((USART_TypeDef *) USART3_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define FMPI2C1 ((FMPI2C_TypeDef *) FMPI2C1_BASE) -#define CAN1 ((CAN_TypeDef *) CAN1_BASE) -#define CAN2 ((CAN_TypeDef *) CAN2_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define TIM8 ((TIM_TypeDef *) TIM8_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SPI4 ((SPI_TypeDef *) SPI4_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define SPI5 ((SPI_TypeDef *) SPI5_BASE) -#define DFSDM1_Channel0 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel0_BASE) -#define DFSDM1_Channel1 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel1_BASE) -#define DFSDM1_Channel2 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel2_BASE) -#define DFSDM1_Channel3 ((DFSDM_Channel_TypeDef *) DFSDM1_Channel3_BASE) -#define DFSDM1_Filter0 ((DFSDM_Filter_TypeDef *) DFSDM1_Filter0_BASE) -#define DFSDM1_Filter1 ((DFSDM_Filter_TypeDef *) DFSDM1_Filter1_BASE) -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOF ((GPIO_TypeDef *) GPIOF_BASE) -#define GPIOG ((GPIO_TypeDef *) GPIOG_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) -#define FSMC_Bank1 ((FSMC_Bank1_TypeDef *) FSMC_Bank1_R_BASE) -#define FSMC_Bank1E ((FSMC_Bank1E_TypeDef *) FSMC_Bank1E_R_BASE) -#define QUADSPI ((QUADSPI_TypeDef *) QSPI_R_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f415xx - * @{ - */ - -#ifndef __STM32F415xx_H -#define __STM32F415xx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1, ADC2 and ADC3 global Interrupts */ - CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */ - CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */ - CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ - CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - USART3_IRQn = 39, /*!< USART3 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */ - TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */ - TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */ - TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare Interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - FSMC_IRQn = 48, /*!< FSMC global Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - UART4_IRQn = 52, /*!< UART4 global Interrupt */ - UART5_IRQn = 53, /*!< UART5 global Interrupt */ - TIM6_DAC_IRQn = 54, /*!< TIM6 global and DAC1&2 underrun error interrupts */ - TIM7_IRQn = 55, /*!< TIM7 global interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */ - CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */ - CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */ - CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - OTG_HS_EP1_OUT_IRQn = 74, /*!< USB OTG HS End Point 1 Out global interrupt */ - OTG_HS_EP1_IN_IRQn = 75, /*!< USB OTG HS End Point 1 In global interrupt */ - OTG_HS_WKUP_IRQn = 76, /*!< USB OTG HS Wakeup through EXTI interrupt */ - OTG_HS_IRQn = 77, /*!< USB OTG HS global interrupt */ - CRYP_IRQn = 79, /*!< CRYP crypto global interrupt */ - HASH_RNG_IRQn = 80, /*!< Hash and Rng global interrupt */ - FPU_IRQn = 81 /*!< FPU global interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - - -/** - * @brief Controller Area Network TxMailBox - */ - -typedef struct -{ - __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ - __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ - __IO uint32_t TDLR; /*!< CAN mailbox data low register */ - __IO uint32_t TDHR; /*!< CAN mailbox data high register */ -} CAN_TxMailBox_TypeDef; - -/** - * @brief Controller Area Network FIFOMailBox - */ - -typedef struct -{ - __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ - __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ - __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ - __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ -} CAN_FIFOMailBox_TypeDef; - -/** - * @brief Controller Area Network FilterRegister - */ - -typedef struct -{ - __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ - __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ -} CAN_FilterRegister_TypeDef; - -/** - * @brief Controller Area Network - */ - -typedef struct -{ - __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ - __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ - __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ - __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ - __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ - __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ - __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ - __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ - uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ - CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ - CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ - uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ - __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ - __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ - uint32_t RESERVED2; /*!< Reserved, 0x208 */ - __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ - uint32_t RESERVED3; /*!< Reserved, 0x210 */ - __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ - uint32_t RESERVED4; /*!< Reserved, 0x218 */ - __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ - uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ - CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ -} CAN_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Digital to Analog Converter - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ - __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ - __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ - __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ - __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ - __IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */ - __IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */ - __IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */ - __IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */ - __IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */ - __IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */ - __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ - __IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */ - __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ -} DAC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - - -/** - * @brief Flexible Static Memory Controller - */ - -typedef struct -{ - __IO uint32_t BTCR[8]; /*!< NOR/PSRAM chip-select control register(BCR) and chip-select timing register(BTR), Address offset: 0x00-1C */ -} FSMC_Bank1_TypeDef; - -/** - * @brief Flexible Static Memory Controller Bank1E - */ - -typedef struct -{ - __IO uint32_t BWTR[7]; /*!< NOR/PSRAM write timing registers, Address offset: 0x104-0x11C */ -} FSMC_Bank1E_TypeDef; - -/** - * @brief Flexible Static Memory Controller Bank2 - */ - -typedef struct -{ - __IO uint32_t PCR2; /*!< NAND Flash control register 2, Address offset: 0x60 */ - __IO uint32_t SR2; /*!< NAND Flash FIFO status and interrupt register 2, Address offset: 0x64 */ - __IO uint32_t PMEM2; /*!< NAND Flash Common memory space timing register 2, Address offset: 0x68 */ - __IO uint32_t PATT2; /*!< NAND Flash Attribute memory space timing register 2, Address offset: 0x6C */ - uint32_t RESERVED0; /*!< Reserved, 0x70 */ - __IO uint32_t ECCR2; /*!< NAND Flash ECC result registers 2, Address offset: 0x74 */ - uint32_t RESERVED1; /*!< Reserved, 0x78 */ - uint32_t RESERVED2; /*!< Reserved, 0x7C */ - __IO uint32_t PCR3; /*!< NAND Flash control register 3, Address offset: 0x80 */ - __IO uint32_t SR3; /*!< NAND Flash FIFO status and interrupt register 3, Address offset: 0x84 */ - __IO uint32_t PMEM3; /*!< NAND Flash Common memory space timing register 3, Address offset: 0x88 */ - __IO uint32_t PATT3; /*!< NAND Flash Attribute memory space timing register 3, Address offset: 0x8C */ - uint32_t RESERVED3; /*!< Reserved, 0x90 */ - __IO uint32_t ECCR3; /*!< NAND Flash ECC result registers 3, Address offset: 0x94 */ -} FSMC_Bank2_3_TypeDef; - -/** - * @brief Flexible Static Memory Controller Bank4 - */ - -typedef struct -{ - __IO uint32_t PCR4; /*!< PC Card control register 4, Address offset: 0xA0 */ - __IO uint32_t SR4; /*!< PC Card FIFO status and interrupt register 4, Address offset: 0xA4 */ - __IO uint32_t PMEM4; /*!< PC Card Common memory space timing register 4, Address offset: 0xA8 */ - __IO uint32_t PATT4; /*!< PC Card Attribute memory space timing register 4, Address offset: 0xAC */ - __IO uint32_t PIO4; /*!< PC Card I/O space timing register 4, Address offset: 0xB0 */ -} FSMC_Bank4_TypeDef; - - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - -/** - * @brief Crypto Processor - */ - -typedef struct -{ - __IO uint32_t CR; /*!< CRYP control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< CRYP status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< CRYP data input register, Address offset: 0x08 */ - __IO uint32_t DOUT; /*!< CRYP data output register, Address offset: 0x0C */ - __IO uint32_t DMACR; /*!< CRYP DMA control register, Address offset: 0x10 */ - __IO uint32_t IMSCR; /*!< CRYP interrupt mask set/clear register, Address offset: 0x14 */ - __IO uint32_t RISR; /*!< CRYP raw interrupt status register, Address offset: 0x18 */ - __IO uint32_t MISR; /*!< CRYP masked interrupt status register, Address offset: 0x1C */ - __IO uint32_t K0LR; /*!< CRYP key left register 0, Address offset: 0x20 */ - __IO uint32_t K0RR; /*!< CRYP key right register 0, Address offset: 0x24 */ - __IO uint32_t K1LR; /*!< CRYP key left register 1, Address offset: 0x28 */ - __IO uint32_t K1RR; /*!< CRYP key right register 1, Address offset: 0x2C */ - __IO uint32_t K2LR; /*!< CRYP key left register 2, Address offset: 0x30 */ - __IO uint32_t K2RR; /*!< CRYP key right register 2, Address offset: 0x34 */ - __IO uint32_t K3LR; /*!< CRYP key left register 3, Address offset: 0x38 */ - __IO uint32_t K3RR; /*!< CRYP key right register 3, Address offset: 0x3C */ - __IO uint32_t IV0LR; /*!< CRYP initialization vector left-word register 0, Address offset: 0x40 */ - __IO uint32_t IV0RR; /*!< CRYP initialization vector right-word register 0, Address offset: 0x44 */ - __IO uint32_t IV1LR; /*!< CRYP initialization vector left-word register 1, Address offset: 0x48 */ - __IO uint32_t IV1RR; /*!< CRYP initialization vector right-word register 1, Address offset: 0x4C */ - __IO uint32_t CSGCMCCM0R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 0, Address offset: 0x50 */ - __IO uint32_t CSGCMCCM1R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 1, Address offset: 0x54 */ - __IO uint32_t CSGCMCCM2R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 2, Address offset: 0x58 */ - __IO uint32_t CSGCMCCM3R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 3, Address offset: 0x5C */ - __IO uint32_t CSGCMCCM4R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 4, Address offset: 0x60 */ - __IO uint32_t CSGCMCCM5R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 5, Address offset: 0x64 */ - __IO uint32_t CSGCMCCM6R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 6, Address offset: 0x68 */ - __IO uint32_t CSGCMCCM7R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 7, Address offset: 0x6C */ - __IO uint32_t CSGCM0R; /*!< CRYP GCM/GMAC context swap register 0, Address offset: 0x70 */ - __IO uint32_t CSGCM1R; /*!< CRYP GCM/GMAC context swap register 1, Address offset: 0x74 */ - __IO uint32_t CSGCM2R; /*!< CRYP GCM/GMAC context swap register 2, Address offset: 0x78 */ - __IO uint32_t CSGCM3R; /*!< CRYP GCM/GMAC context swap register 3, Address offset: 0x7C */ - __IO uint32_t CSGCM4R; /*!< CRYP GCM/GMAC context swap register 4, Address offset: 0x80 */ - __IO uint32_t CSGCM5R; /*!< CRYP GCM/GMAC context swap register 5, Address offset: 0x84 */ - __IO uint32_t CSGCM6R; /*!< CRYP GCM/GMAC context swap register 6, Address offset: 0x88 */ - __IO uint32_t CSGCM7R; /*!< CRYP GCM/GMAC context swap register 7, Address offset: 0x8C */ -} CRYP_TypeDef; - -/** - * @brief HASH - */ - -typedef struct -{ - __IO uint32_t CR; /*!< HASH control register, Address offset: 0x00 */ - __IO uint32_t DIN; /*!< HASH data input register, Address offset: 0x04 */ - __IO uint32_t STR; /*!< HASH start register, Address offset: 0x08 */ - __IO uint32_t HR[5]; /*!< HASH digest registers, Address offset: 0x0C-0x1C */ - __IO uint32_t IMR; /*!< HASH interrupt enable register, Address offset: 0x20 */ - __IO uint32_t SR; /*!< HASH status register, Address offset: 0x24 */ - uint32_t RESERVED[52]; /*!< Reserved, 0x28-0xF4 */ - __IO uint32_t CSR[54]; /*!< HASH context swap registers, Address offset: 0x0F8-0x1CC */ -} HASH_TypeDef; - -/** - * @brief HASH_DIGEST - */ - -typedef struct -{ - __IO uint32_t HR[8]; /*!< HASH digest registers, Address offset: 0x310-0x32C */ -} HASH_DIGEST_TypeDef; - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - - -/** - * @brief __USB_OTG_Core_register - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register Address offset : 0x00 */ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register Address offset : 0x04 */ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register Address offset : 0x08 */ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register Address offset : 0x0C */ - __IO uint32_t GRSTCTL; /*!< Core Reset Register Address offset : 0x10 */ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register Address offset : 0x14 */ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register Address offset : 0x18 */ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register Address offset : 0x1C */ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register Address offset : 0x20 */ - __IO uint32_t GRXFSIZ; /* Receive FIFO Size Register Address offset : 0x24 */ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register Address offset : 0x28 */ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg Address offset : 0x2C */ - uint32_t Reserved30[2]; /* Reserved Address offset : 0x30 */ - __IO uint32_t GCCFG; /*!< General Purpose IO Register Address offset : 0x38 */ - __IO uint32_t CID; /*!< User ID Register Address offset : 0x3C */ - uint32_t Reserved40[48]; /*!< Reserved Address offset : 0x40-0xFF */ - __IO uint32_t HPTXFSIZ; /*!< Host Periodic Tx FIFO Size Reg Address offset : 0x100 */ - __IO uint32_t DIEPTXF[0x0F]; /*!< dev Periodic Transmit FIFO */ -} -USB_OTG_GlobalTypeDef; - - - -/** - * @brief __device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /*!< dev Configuration Register Address offset : 0x800 */ - __IO uint32_t DCTL; /*!< dev Control Register Address offset : 0x804 */ - __IO uint32_t DSTS; /*!< dev Status Register (RO) Address offset : 0x808 */ - uint32_t Reserved0C; /*!< Reserved Address offset : 0x80C */ - __IO uint32_t DIEPMSK; /* !< dev IN Endpoint Mask Address offset : 0x810 */ - __IO uint32_t DOEPMSK; /*!< dev OUT Endpoint Mask Address offset : 0x814 */ - __IO uint32_t DAINT; /*!< dev All Endpoints Itr Reg Address offset : 0x818 */ - __IO uint32_t DAINTMSK; /*!< dev All Endpoints Itr Mask Address offset : 0x81C */ - uint32_t Reserved20; /*!< Reserved Address offset : 0x820 */ - uint32_t Reserved9; /*!< Reserved Address offset : 0x824 */ - __IO uint32_t DVBUSDIS; /*!< dev VBUS discharge Register Address offset : 0x828 */ - __IO uint32_t DVBUSPULSE; /*!< dev VBUS Pulse Register Address offset : 0x82C */ - __IO uint32_t DTHRCTL; /*!< dev thr Address offset : 0x830 */ - __IO uint32_t DIEPEMPMSK; /*!< dev empty msk Address offset : 0x834 */ - __IO uint32_t DEACHINT; /*!< dedicated EP interrupt Address offset : 0x838 */ - __IO uint32_t DEACHMSK; /*!< dedicated EP msk Address offset : 0x83C */ - uint32_t Reserved40; /*!< dedicated EP mask Address offset : 0x840 */ - __IO uint32_t DINEP1MSK; /*!< dedicated EP mask Address offset : 0x844 */ - uint32_t Reserved44[15]; /*!< Reserved Address offset : 0x844-0x87C */ - __IO uint32_t DOUTEP1MSK; /*!< dedicated EP msk Address offset : 0x884 */ -} -USB_OTG_DeviceTypeDef; - - -/** - * @brief __IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /* dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /* Reserved 900h + (ep_num * 20h) + 04h */ - __IO uint32_t DIEPINT; /* dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /* Reserved 900h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DIEPTSIZ; /* IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h */ - __IO uint32_t DIEPDMA; /* IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h */ - __IO uint32_t DTXFSTS; /*IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h */ - uint32_t Reserved18; /* Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch */ -} -USB_OTG_INEndpointTypeDef; - - -/** - * @brief __OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /* dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved B00h + (ep_num * 20h) + 04h*/ - __IO uint32_t DOEPINT; /* dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved B00h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DOEPTSIZ; /* dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h*/ - __IO uint32_t DOEPDMA; /* dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h*/ - uint32_t Reserved18[2]; /* Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch*/ -} -USB_OTG_OUTEndpointTypeDef; - - -/** - * @brief __Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /* Host Configuration Register 400h*/ - __IO uint32_t HFIR; /* Host Frame Interval Register 404h*/ - __IO uint32_t HFNUM; /* Host Frame Nbr/Frame Remaining 408h*/ - uint32_t Reserved40C; /* Reserved 40Ch*/ - __IO uint32_t HPTXSTS; /* Host Periodic Tx FIFO/ Queue Status 410h*/ - __IO uint32_t HAINT; /* Host All Channels Interrupt Register 414h*/ - __IO uint32_t HAINTMSK; /* Host All Channels Interrupt Mask 418h*/ -} -USB_OTG_HostTypeDef; - - -/** - * @brief __Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; - __IO uint32_t HCSPLT; - __IO uint32_t HCINT; - __IO uint32_t HCINTMSK; - __IO uint32_t HCTSIZ; - __IO uint32_t HCDMA; - uint32_t Reserved[2]; -} -USB_OTG_HostChannelTypeDef; - - -/** - * @brief Peripheral_memory_map - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define CCMDATARAM_BASE 0x10000000U /*!< CCM(core coupled memory) data RAM(64 KB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(112 KB) base address in the alias region */ -#define SRAM2_BASE 0x2001C000U /*!< SRAM2(16 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define BKPSRAM_BASE 0x40024000U /*!< Backup SRAM(4 KB) base address in the alias region */ -#define FSMC_R_BASE 0xA0000000U /*!< FSMC registers base address */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(112 KB) base address in the bit-band region */ -#define SRAM2_BB_BASE 0x22380000U /*!< SRAM2(16 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define BKPSRAM_BB_BASE 0x42480000U /*!< Backup SRAM(4 KB) base address in the bit-band region */ -#define FLASH_END 0x080FFFFFU /*!< FLASH end address */ -#define CCMDATARAM_END 0x1000FFFFU /*!< CCM data RAM end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define TIM7_BASE (APB1PERIPH_BASE + 0x1400U) -#define TIM12_BASE (APB1PERIPH_BASE + 0x1800U) -#define TIM13_BASE (APB1PERIPH_BASE + 0x1C00U) -#define TIM14_BASE (APB1PERIPH_BASE + 0x2000U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define USART3_BASE (APB1PERIPH_BASE + 0x4800U) -#define UART4_BASE (APB1PERIPH_BASE + 0x4C00U) -#define UART5_BASE (APB1PERIPH_BASE + 0x5000U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define CAN1_BASE (APB1PERIPH_BASE + 0x6400U) -#define CAN2_BASE (APB1PERIPH_BASE + 0x6800U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) -#define DAC_BASE (APB1PERIPH_BASE + 0x7400U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define TIM8_BASE (APB2PERIPH_BASE + 0x0400U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC2_BASE (APB2PERIPH_BASE + 0x2100U) -#define ADC3_BASE (APB2PERIPH_BASE + 0x2200U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOF_BASE (AHB1PERIPH_BASE + 0x1400U) -#define GPIOG_BASE (AHB1PERIPH_BASE + 0x1800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define GPIOI_BASE (AHB1PERIPH_BASE + 0x2000U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) - -/*!< AHB2 peripherals */ -#define CRYP_BASE (AHB2PERIPH_BASE + 0x60000U) -#define HASH_BASE (AHB2PERIPH_BASE + 0x60400U) -#define HASH_DIGEST_BASE (AHB2PERIPH_BASE + 0x60710U) -#define RNG_BASE (AHB2PERIPH_BASE + 0x60800U) - -/*!< FSMC Bankx registers base address */ -#define FSMC_Bank1_R_BASE (FSMC_R_BASE + 0x0000U) -#define FSMC_Bank1E_R_BASE (FSMC_R_BASE + 0x0104U) -#define FSMC_Bank2_3_R_BASE (FSMC_R_BASE + 0x0060U) -#define FSMC_Bank4_R_BASE (FSMC_R_BASE + 0x00A0U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_HS_PERIPH_BASE 0x40040000U -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define TIM7 ((TIM_TypeDef *) TIM7_BASE) -#define TIM12 ((TIM_TypeDef *) TIM12_BASE) -#define TIM13 ((TIM_TypeDef *) TIM13_BASE) -#define TIM14 ((TIM_TypeDef *) TIM14_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define USART3 ((USART_TypeDef *) USART3_BASE) -#define UART4 ((USART_TypeDef *) UART4_BASE) -#define UART5 ((USART_TypeDef *) UART5_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define CAN1 ((CAN_TypeDef *) CAN1_BASE) -#define CAN2 ((CAN_TypeDef *) CAN2_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define DAC ((DAC_TypeDef *) DAC_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define TIM8 ((TIM_TypeDef *) TIM8_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define ADC2 ((ADC_TypeDef *) ADC2_BASE) -#define ADC3 ((ADC_TypeDef *) ADC3_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOF ((GPIO_TypeDef *) GPIOF_BASE) -#define GPIOG ((GPIO_TypeDef *) GPIOG_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define GPIOI ((GPIO_TypeDef *) GPIOI_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define CRYP ((CRYP_TypeDef *) CRYP_BASE) -#define HASH ((HASH_TypeDef *) HASH_BASE) -#define HASH_DIGEST ((HASH_DIGEST_TypeDef *) HASH_DIGEST_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) -#define FSMC_Bank1 ((FSMC_Bank1_TypeDef *) FSMC_Bank1_R_BASE) -#define FSMC_Bank1E ((FSMC_Bank1E_TypeDef *) FSMC_Bank1E_R_BASE) -#define FSMC_Bank2_3 ((FSMC_Bank2_3_TypeDef *) FSMC_Bank2_3_R_BASE) -#define FSMC_Bank4 ((FSMC_Bank4_TypeDef *) FSMC_Bank4_R_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) -#define USB_OTG_HS ((USB_OTG_GlobalTypeDef *) USB_OTG_HS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f417xx - * @{ - */ - -#ifndef __STM32F417xx_H -#define __STM32F417xx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1, ADC2 and ADC3 global Interrupts */ - CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */ - CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */ - CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ - CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - USART3_IRQn = 39, /*!< USART3 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */ - TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */ - TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */ - TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare Interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - FSMC_IRQn = 48, /*!< FSMC global Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - UART4_IRQn = 52, /*!< UART4 global Interrupt */ - UART5_IRQn = 53, /*!< UART5 global Interrupt */ - TIM6_DAC_IRQn = 54, /*!< TIM6 global and DAC1&2 underrun error interrupts */ - TIM7_IRQn = 55, /*!< TIM7 global interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - ETH_IRQn = 61, /*!< Ethernet global Interrupt */ - ETH_WKUP_IRQn = 62, /*!< Ethernet Wakeup through EXTI line Interrupt */ - CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */ - CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */ - CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */ - CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - OTG_HS_EP1_OUT_IRQn = 74, /*!< USB OTG HS End Point 1 Out global interrupt */ - OTG_HS_EP1_IN_IRQn = 75, /*!< USB OTG HS End Point 1 In global interrupt */ - OTG_HS_WKUP_IRQn = 76, /*!< USB OTG HS Wakeup through EXTI interrupt */ - OTG_HS_IRQn = 77, /*!< USB OTG HS global interrupt */ - DCMI_IRQn = 78, /*!< DCMI global interrupt */ - CRYP_IRQn = 79, /*!< CRYP crypto global interrupt */ - HASH_RNG_IRQn = 80, /*!< Hash and Rng global interrupt */ - FPU_IRQn = 81 /*!< FPU global interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - - -/** - * @brief Controller Area Network TxMailBox - */ - -typedef struct -{ - __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ - __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ - __IO uint32_t TDLR; /*!< CAN mailbox data low register */ - __IO uint32_t TDHR; /*!< CAN mailbox data high register */ -} CAN_TxMailBox_TypeDef; - -/** - * @brief Controller Area Network FIFOMailBox - */ - -typedef struct -{ - __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ - __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ - __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ - __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ -} CAN_FIFOMailBox_TypeDef; - -/** - * @brief Controller Area Network FilterRegister - */ - -typedef struct -{ - __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ - __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ -} CAN_FilterRegister_TypeDef; - -/** - * @brief Controller Area Network - */ - -typedef struct -{ - __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ - __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ - __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ - __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ - __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ - __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ - __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ - __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ - uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ - CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ - CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ - uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ - __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ - __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ - uint32_t RESERVED2; /*!< Reserved, 0x208 */ - __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ - uint32_t RESERVED3; /*!< Reserved, 0x210 */ - __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ - uint32_t RESERVED4; /*!< Reserved, 0x218 */ - __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ - uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ - CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ -} CAN_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Digital to Analog Converter - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ - __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ - __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ - __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ - __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ - __IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */ - __IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */ - __IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */ - __IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */ - __IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */ - __IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */ - __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ - __IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */ - __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ -} DAC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - -/** - * @brief DCMI - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DCMI control register 1, Address offset: 0x00 */ - __IO uint32_t SR; /*!< DCMI status register, Address offset: 0x04 */ - __IO uint32_t RISR; /*!< DCMI raw interrupt status register, Address offset: 0x08 */ - __IO uint32_t IER; /*!< DCMI interrupt enable register, Address offset: 0x0C */ - __IO uint32_t MISR; /*!< DCMI masked interrupt status register, Address offset: 0x10 */ - __IO uint32_t ICR; /*!< DCMI interrupt clear register, Address offset: 0x14 */ - __IO uint32_t ESCR; /*!< DCMI embedded synchronization code register, Address offset: 0x18 */ - __IO uint32_t ESUR; /*!< DCMI embedded synchronization unmask register, Address offset: 0x1C */ - __IO uint32_t CWSTRTR; /*!< DCMI crop window start, Address offset: 0x20 */ - __IO uint32_t CWSIZER; /*!< DCMI crop window size, Address offset: 0x24 */ - __IO uint32_t DR; /*!< DCMI data register, Address offset: 0x28 */ -} DCMI_TypeDef; - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - - -/** - * @brief Ethernet MAC - */ - -typedef struct -{ - __IO uint32_t MACCR; - __IO uint32_t MACFFR; - __IO uint32_t MACHTHR; - __IO uint32_t MACHTLR; - __IO uint32_t MACMIIAR; - __IO uint32_t MACMIIDR; - __IO uint32_t MACFCR; - __IO uint32_t MACVLANTR; /* 8 */ - uint32_t RESERVED0[2]; - __IO uint32_t MACRWUFFR; /* 11 */ - __IO uint32_t MACPMTCSR; - uint32_t RESERVED1[2]; - __IO uint32_t MACSR; /* 15 */ - __IO uint32_t MACIMR; - __IO uint32_t MACA0HR; - __IO uint32_t MACA0LR; - __IO uint32_t MACA1HR; - __IO uint32_t MACA1LR; - __IO uint32_t MACA2HR; - __IO uint32_t MACA2LR; - __IO uint32_t MACA3HR; - __IO uint32_t MACA3LR; /* 24 */ - uint32_t RESERVED2[40]; - __IO uint32_t MMCCR; /* 65 */ - __IO uint32_t MMCRIR; - __IO uint32_t MMCTIR; - __IO uint32_t MMCRIMR; - __IO uint32_t MMCTIMR; /* 69 */ - uint32_t RESERVED3[14]; - __IO uint32_t MMCTGFSCCR; /* 84 */ - __IO uint32_t MMCTGFMSCCR; - uint32_t RESERVED4[5]; - __IO uint32_t MMCTGFCR; - uint32_t RESERVED5[10]; - __IO uint32_t MMCRFCECR; - __IO uint32_t MMCRFAECR; - uint32_t RESERVED6[10]; - __IO uint32_t MMCRGUFCR; - uint32_t RESERVED7[334]; - __IO uint32_t PTPTSCR; - __IO uint32_t PTPSSIR; - __IO uint32_t PTPTSHR; - __IO uint32_t PTPTSLR; - __IO uint32_t PTPTSHUR; - __IO uint32_t PTPTSLUR; - __IO uint32_t PTPTSAR; - __IO uint32_t PTPTTHR; - __IO uint32_t PTPTTLR; - __IO uint32_t RESERVED8; - __IO uint32_t PTPTSSR; - uint32_t RESERVED9[565]; - __IO uint32_t DMABMR; - __IO uint32_t DMATPDR; - __IO uint32_t DMARPDR; - __IO uint32_t DMARDLAR; - __IO uint32_t DMATDLAR; - __IO uint32_t DMASR; - __IO uint32_t DMAOMR; - __IO uint32_t DMAIER; - __IO uint32_t DMAMFBOCR; - __IO uint32_t DMARSWTR; - uint32_t RESERVED10[8]; - __IO uint32_t DMACHTDR; - __IO uint32_t DMACHRDR; - __IO uint32_t DMACHTBAR; - __IO uint32_t DMACHRBAR; -} ETH_TypeDef; - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - - -/** - * @brief Flexible Static Memory Controller - */ - -typedef struct -{ - __IO uint32_t BTCR[8]; /*!< NOR/PSRAM chip-select control register(BCR) and chip-select timing register(BTR), Address offset: 0x00-1C */ -} FSMC_Bank1_TypeDef; - -/** - * @brief Flexible Static Memory Controller Bank1E - */ - -typedef struct -{ - __IO uint32_t BWTR[7]; /*!< NOR/PSRAM write timing registers, Address offset: 0x104-0x11C */ -} FSMC_Bank1E_TypeDef; - -/** - * @brief Flexible Static Memory Controller Bank2 - */ - -typedef struct -{ - __IO uint32_t PCR2; /*!< NAND Flash control register 2, Address offset: 0x60 */ - __IO uint32_t SR2; /*!< NAND Flash FIFO status and interrupt register 2, Address offset: 0x64 */ - __IO uint32_t PMEM2; /*!< NAND Flash Common memory space timing register 2, Address offset: 0x68 */ - __IO uint32_t PATT2; /*!< NAND Flash Attribute memory space timing register 2, Address offset: 0x6C */ - uint32_t RESERVED0; /*!< Reserved, 0x70 */ - __IO uint32_t ECCR2; /*!< NAND Flash ECC result registers 2, Address offset: 0x74 */ - uint32_t RESERVED1; /*!< Reserved, 0x78 */ - uint32_t RESERVED2; /*!< Reserved, 0x7C */ - __IO uint32_t PCR3; /*!< NAND Flash control register 3, Address offset: 0x80 */ - __IO uint32_t SR3; /*!< NAND Flash FIFO status and interrupt register 3, Address offset: 0x84 */ - __IO uint32_t PMEM3; /*!< NAND Flash Common memory space timing register 3, Address offset: 0x88 */ - __IO uint32_t PATT3; /*!< NAND Flash Attribute memory space timing register 3, Address offset: 0x8C */ - uint32_t RESERVED3; /*!< Reserved, 0x90 */ - __IO uint32_t ECCR3; /*!< NAND Flash ECC result registers 3, Address offset: 0x94 */ -} FSMC_Bank2_3_TypeDef; - -/** - * @brief Flexible Static Memory Controller Bank4 - */ - -typedef struct -{ - __IO uint32_t PCR4; /*!< PC Card control register 4, Address offset: 0xA0 */ - __IO uint32_t SR4; /*!< PC Card FIFO status and interrupt register 4, Address offset: 0xA4 */ - __IO uint32_t PMEM4; /*!< PC Card Common memory space timing register 4, Address offset: 0xA8 */ - __IO uint32_t PATT4; /*!< PC Card Attribute memory space timing register 4, Address offset: 0xAC */ - __IO uint32_t PIO4; /*!< PC Card I/O space timing register 4, Address offset: 0xB0 */ -} FSMC_Bank4_TypeDef; - - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - -/** - * @brief Crypto Processor - */ - -typedef struct -{ - __IO uint32_t CR; /*!< CRYP control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< CRYP status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< CRYP data input register, Address offset: 0x08 */ - __IO uint32_t DOUT; /*!< CRYP data output register, Address offset: 0x0C */ - __IO uint32_t DMACR; /*!< CRYP DMA control register, Address offset: 0x10 */ - __IO uint32_t IMSCR; /*!< CRYP interrupt mask set/clear register, Address offset: 0x14 */ - __IO uint32_t RISR; /*!< CRYP raw interrupt status register, Address offset: 0x18 */ - __IO uint32_t MISR; /*!< CRYP masked interrupt status register, Address offset: 0x1C */ - __IO uint32_t K0LR; /*!< CRYP key left register 0, Address offset: 0x20 */ - __IO uint32_t K0RR; /*!< CRYP key right register 0, Address offset: 0x24 */ - __IO uint32_t K1LR; /*!< CRYP key left register 1, Address offset: 0x28 */ - __IO uint32_t K1RR; /*!< CRYP key right register 1, Address offset: 0x2C */ - __IO uint32_t K2LR; /*!< CRYP key left register 2, Address offset: 0x30 */ - __IO uint32_t K2RR; /*!< CRYP key right register 2, Address offset: 0x34 */ - __IO uint32_t K3LR; /*!< CRYP key left register 3, Address offset: 0x38 */ - __IO uint32_t K3RR; /*!< CRYP key right register 3, Address offset: 0x3C */ - __IO uint32_t IV0LR; /*!< CRYP initialization vector left-word register 0, Address offset: 0x40 */ - __IO uint32_t IV0RR; /*!< CRYP initialization vector right-word register 0, Address offset: 0x44 */ - __IO uint32_t IV1LR; /*!< CRYP initialization vector left-word register 1, Address offset: 0x48 */ - __IO uint32_t IV1RR; /*!< CRYP initialization vector right-word register 1, Address offset: 0x4C */ - __IO uint32_t CSGCMCCM0R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 0, Address offset: 0x50 */ - __IO uint32_t CSGCMCCM1R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 1, Address offset: 0x54 */ - __IO uint32_t CSGCMCCM2R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 2, Address offset: 0x58 */ - __IO uint32_t CSGCMCCM3R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 3, Address offset: 0x5C */ - __IO uint32_t CSGCMCCM4R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 4, Address offset: 0x60 */ - __IO uint32_t CSGCMCCM5R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 5, Address offset: 0x64 */ - __IO uint32_t CSGCMCCM6R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 6, Address offset: 0x68 */ - __IO uint32_t CSGCMCCM7R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 7, Address offset: 0x6C */ - __IO uint32_t CSGCM0R; /*!< CRYP GCM/GMAC context swap register 0, Address offset: 0x70 */ - __IO uint32_t CSGCM1R; /*!< CRYP GCM/GMAC context swap register 1, Address offset: 0x74 */ - __IO uint32_t CSGCM2R; /*!< CRYP GCM/GMAC context swap register 2, Address offset: 0x78 */ - __IO uint32_t CSGCM3R; /*!< CRYP GCM/GMAC context swap register 3, Address offset: 0x7C */ - __IO uint32_t CSGCM4R; /*!< CRYP GCM/GMAC context swap register 4, Address offset: 0x80 */ - __IO uint32_t CSGCM5R; /*!< CRYP GCM/GMAC context swap register 5, Address offset: 0x84 */ - __IO uint32_t CSGCM6R; /*!< CRYP GCM/GMAC context swap register 6, Address offset: 0x88 */ - __IO uint32_t CSGCM7R; /*!< CRYP GCM/GMAC context swap register 7, Address offset: 0x8C */ -} CRYP_TypeDef; - -/** - * @brief HASH - */ - -typedef struct -{ - __IO uint32_t CR; /*!< HASH control register, Address offset: 0x00 */ - __IO uint32_t DIN; /*!< HASH data input register, Address offset: 0x04 */ - __IO uint32_t STR; /*!< HASH start register, Address offset: 0x08 */ - __IO uint32_t HR[5]; /*!< HASH digest registers, Address offset: 0x0C-0x1C */ - __IO uint32_t IMR; /*!< HASH interrupt enable register, Address offset: 0x20 */ - __IO uint32_t SR; /*!< HASH status register, Address offset: 0x24 */ - uint32_t RESERVED[52]; /*!< Reserved, 0x28-0xF4 */ - __IO uint32_t CSR[54]; /*!< HASH context swap registers, Address offset: 0x0F8-0x1CC */ -} HASH_TypeDef; - -/** - * @brief HASH_DIGEST - */ - -typedef struct -{ - __IO uint32_t HR[8]; /*!< HASH digest registers, Address offset: 0x310-0x32C */ -} HASH_DIGEST_TypeDef; - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - - -/** - * @brief __USB_OTG_Core_register - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register 000h*/ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register 004h*/ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register 008h*/ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register 00Ch*/ - __IO uint32_t GRSTCTL; /*!< Core Reset Register 010h*/ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register 014h*/ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register 018h*/ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register 01Ch*/ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register 020h*/ - __IO uint32_t GRXFSIZ; /* Receive FIFO Size Register 024h*/ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register 028h*/ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg 02Ch*/ - uint32_t Reserved30[2]; /* Reserved 030h*/ - __IO uint32_t GCCFG; /* General Purpose IO Register 038h*/ - __IO uint32_t CID; /* User ID Register 03Ch*/ - uint32_t Reserved40[48]; /* Reserved 040h-0FFh*/ - __IO uint32_t HPTXFSIZ; /* Host Periodic Tx FIFO Size Reg 100h*/ - __IO uint32_t DIEPTXF[0x0F];/* dev Periodic Transmit FIFO */ -} -USB_OTG_GlobalTypeDef; - - - -/** - * @brief __device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /* dev Configuration Register 800h*/ - __IO uint32_t DCTL; /* dev Control Register 804h*/ - __IO uint32_t DSTS; /* dev Status Register (RO) 808h*/ - uint32_t Reserved0C; /* Reserved 80Ch*/ - __IO uint32_t DIEPMSK; /* dev IN Endpoint Mask 810h*/ - __IO uint32_t DOEPMSK; /* dev OUT Endpoint Mask 814h*/ - __IO uint32_t DAINT; /* dev All Endpoints Itr Reg 818h*/ - __IO uint32_t DAINTMSK; /* dev All Endpoints Itr Mask 81Ch*/ - uint32_t Reserved20; /* Reserved 820h*/ - uint32_t Reserved9; /* Reserved 824h*/ - __IO uint32_t DVBUSDIS; /* dev VBUS discharge Register 828h*/ - __IO uint32_t DVBUSPULSE; /* dev VBUS Pulse Register 82Ch*/ - __IO uint32_t DTHRCTL; /* dev thr 830h*/ - __IO uint32_t DIEPEMPMSK; /* dev empty msk 834h*/ - __IO uint32_t DEACHINT; /* dedicated EP interrupt 838h*/ - __IO uint32_t DEACHMSK; /* dedicated EP msk 83Ch*/ - uint32_t Reserved40; /* dedicated EP mask 840h*/ - __IO uint32_t DINEP1MSK; /* dedicated EP mask 844h*/ - uint32_t Reserved44[15]; /* Reserved 844-87Ch*/ - __IO uint32_t DOUTEP1MSK; /* dedicated EP msk 884h*/ -} -USB_OTG_DeviceTypeDef; - - -/** - * @brief __IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /* dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved 900h + (ep_num * 20h) + 04h*/ - __IO uint32_t DIEPINT; /* dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved 900h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DIEPTSIZ; /* IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h*/ - __IO uint32_t DIEPDMA; /* IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h*/ - __IO uint32_t DTXFSTS;/*IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h*/ - uint32_t Reserved18; /* Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch*/ -} -USB_OTG_INEndpointTypeDef; - - -/** - * @brief __OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /* dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved B00h + (ep_num * 20h) + 04h*/ - __IO uint32_t DOEPINT; /* dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved B00h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DOEPTSIZ; /* dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h*/ - __IO uint32_t DOEPDMA; /* dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h*/ - uint32_t Reserved18[2]; /* Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch*/ -} -USB_OTG_OUTEndpointTypeDef; - - -/** - * @brief __Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /* Host Configuration Register 400h*/ - __IO uint32_t HFIR; /* Host Frame Interval Register 404h*/ - __IO uint32_t HFNUM; /* Host Frame Nbr/Frame Remaining 408h*/ - uint32_t Reserved40C; /* Reserved 40Ch*/ - __IO uint32_t HPTXSTS; /* Host Periodic Tx FIFO/ Queue Status 410h*/ - __IO uint32_t HAINT; /* Host All Channels Interrupt Register 414h*/ - __IO uint32_t HAINTMSK; /* Host All Channels Interrupt Mask 418h*/ -} -USB_OTG_HostTypeDef; - - -/** - * @brief __Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; - __IO uint32_t HCSPLT; - __IO uint32_t HCINT; - __IO uint32_t HCINTMSK; - __IO uint32_t HCTSIZ; - __IO uint32_t HCDMA; - uint32_t Reserved[2]; -} -USB_OTG_HostChannelTypeDef; - - -/** - * @brief Peripheral_memory_map - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define CCMDATARAM_BASE 0x10000000U /*!< CCM(core coupled memory) data RAM(64 KB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(112 KB) base address in the alias region */ -#define SRAM2_BASE 0x2001C000U /*!< SRAM2(16 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define BKPSRAM_BASE 0x40024000U /*!< Backup SRAM(4 KB) base address in the alias region */ -#define FSMC_R_BASE 0xA0000000U /*!< FSMC registers base address */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(112 KB) base address in the bit-band region */ -#define SRAM2_BB_BASE 0x22380000U /*!< SRAM2(16 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define BKPSRAM_BB_BASE 0x42480000U /*!< Backup SRAM(4 KB) base address in the bit-band region */ -#define FLASH_END 0x080FFFFFU /*!< FLASH end address */ -#define CCMDATARAM_END 0x1000FFFFU /*!< CCM data RAM end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define TIM7_BASE (APB1PERIPH_BASE + 0x1400U) -#define TIM12_BASE (APB1PERIPH_BASE + 0x1800U) -#define TIM13_BASE (APB1PERIPH_BASE + 0x1C00U) -#define TIM14_BASE (APB1PERIPH_BASE + 0x2000U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define USART3_BASE (APB1PERIPH_BASE + 0x4800U) -#define UART4_BASE (APB1PERIPH_BASE + 0x4C00U) -#define UART5_BASE (APB1PERIPH_BASE + 0x5000U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define CAN1_BASE (APB1PERIPH_BASE + 0x6400U) -#define CAN2_BASE (APB1PERIPH_BASE + 0x6800U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) -#define DAC_BASE (APB1PERIPH_BASE + 0x7400U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define TIM8_BASE (APB2PERIPH_BASE + 0x0400U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC2_BASE (APB2PERIPH_BASE + 0x2100U) -#define ADC3_BASE (APB2PERIPH_BASE + 0x2200U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOF_BASE (AHB1PERIPH_BASE + 0x1400U) -#define GPIOG_BASE (AHB1PERIPH_BASE + 0x1800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define GPIOI_BASE (AHB1PERIPH_BASE + 0x2000U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) -#define ETH_BASE (AHB1PERIPH_BASE + 0x8000U) -#define ETH_MAC_BASE (ETH_BASE) -#define ETH_MMC_BASE (ETH_BASE + 0x0100U) -#define ETH_PTP_BASE (ETH_BASE + 0x0700U) -#define ETH_DMA_BASE (ETH_BASE + 0x1000U) - -/*!< AHB2 peripherals */ -#define DCMI_BASE (AHB2PERIPH_BASE + 0x50000U) -#define CRYP_BASE (AHB2PERIPH_BASE + 0x60000U) -#define HASH_BASE (AHB2PERIPH_BASE + 0x60400U) -#define HASH_DIGEST_BASE (AHB2PERIPH_BASE + 0x60710U) -#define RNG_BASE (AHB2PERIPH_BASE + 0x60800U) - -/*!< FSMC Bankx registers base address */ -#define FSMC_Bank1_R_BASE (FSMC_R_BASE + 0x0000U) -#define FSMC_Bank1E_R_BASE (FSMC_R_BASE + 0x0104U) -#define FSMC_Bank2_3_R_BASE (FSMC_R_BASE + 0x0060U) -#define FSMC_Bank4_R_BASE (FSMC_R_BASE + 0x00A0U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_HS_PERIPH_BASE 0x40040000U -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define TIM7 ((TIM_TypeDef *) TIM7_BASE) -#define TIM12 ((TIM_TypeDef *) TIM12_BASE) -#define TIM13 ((TIM_TypeDef *) TIM13_BASE) -#define TIM14 ((TIM_TypeDef *) TIM14_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define USART3 ((USART_TypeDef *) USART3_BASE) -#define UART4 ((USART_TypeDef *) UART4_BASE) -#define UART5 ((USART_TypeDef *) UART5_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define CAN1 ((CAN_TypeDef *) CAN1_BASE) -#define CAN2 ((CAN_TypeDef *) CAN2_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define DAC ((DAC_TypeDef *) DAC_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define TIM8 ((TIM_TypeDef *) TIM8_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define ADC2 ((ADC_TypeDef *) ADC2_BASE) -#define ADC3 ((ADC_TypeDef *) ADC3_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOF ((GPIO_TypeDef *) GPIOF_BASE) -#define GPIOG ((GPIO_TypeDef *) GPIOG_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define GPIOI ((GPIO_TypeDef *) GPIOI_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define ETH ((ETH_TypeDef *) ETH_BASE) -#define DCMI ((DCMI_TypeDef *) DCMI_BASE) -#define CRYP ((CRYP_TypeDef *) CRYP_BASE) -#define HASH ((HASH_TypeDef *) HASH_BASE) -#define HASH_DIGEST ((HASH_DIGEST_TypeDef *) HASH_DIGEST_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) -#define FSMC_Bank1 ((FSMC_Bank1_TypeDef *) FSMC_Bank1_R_BASE) -#define FSMC_Bank1E ((FSMC_Bank1E_TypeDef *) FSMC_Bank1E_R_BASE) -#define FSMC_Bank2_3 ((FSMC_Bank2_3_TypeDef *) FSMC_Bank2_3_R_BASE) -#define FSMC_Bank4 ((FSMC_Bank4_TypeDef *) FSMC_Bank4_R_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) -#define USB_OTG_HS ((USB_OTG_GlobalTypeDef *) USB_OTG_HS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS_Device - * @{ - */ - -/** @addtogroup stm32f427xx - * @{ - */ - -#ifndef __stm32f427xx_H -#define __stm32f427xx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1, ADC2 and ADC3 global Interrupts */ - CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */ - CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */ - CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ - CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - USART3_IRQn = 39, /*!< USART3 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */ - TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */ - TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */ - TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare Interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - FMC_IRQn = 48, /*!< FMC global Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - UART4_IRQn = 52, /*!< UART4 global Interrupt */ - UART5_IRQn = 53, /*!< UART5 global Interrupt */ - TIM6_DAC_IRQn = 54, /*!< TIM6 global and DAC1&2 underrun error interrupts */ - TIM7_IRQn = 55, /*!< TIM7 global interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - ETH_IRQn = 61, /*!< Ethernet global Interrupt */ - ETH_WKUP_IRQn = 62, /*!< Ethernet Wakeup through EXTI line Interrupt */ - CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */ - CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */ - CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */ - CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - OTG_HS_EP1_OUT_IRQn = 74, /*!< USB OTG HS End Point 1 Out global interrupt */ - OTG_HS_EP1_IN_IRQn = 75, /*!< USB OTG HS End Point 1 In global interrupt */ - OTG_HS_WKUP_IRQn = 76, /*!< USB OTG HS Wakeup through EXTI interrupt */ - OTG_HS_IRQn = 77, /*!< USB OTG HS global interrupt */ - DCMI_IRQn = 78, /*!< DCMI global interrupt */ - HASH_RNG_IRQn = 80, /*!< Hash and RNG global interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - UART7_IRQn = 82, /*!< UART7 global interrupt */ - UART8_IRQn = 83, /*!< UART8 global interrupt */ - SPI4_IRQn = 84, /*!< SPI4 global Interrupt */ - SPI5_IRQn = 85, /*!< SPI5 global Interrupt */ - SPI6_IRQn = 86, /*!< SPI6 global Interrupt */ - SAI1_IRQn = 87, /*!< SAI1 global Interrupt */ - DMA2D_IRQn = 90 /*!< DMA2D global Interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - - -/** - * @brief Controller Area Network TxMailBox - */ - -typedef struct -{ - __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ - __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ - __IO uint32_t TDLR; /*!< CAN mailbox data low register */ - __IO uint32_t TDHR; /*!< CAN mailbox data high register */ -} CAN_TxMailBox_TypeDef; - -/** - * @brief Controller Area Network FIFOMailBox - */ - -typedef struct -{ - __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ - __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ - __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ - __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ -} CAN_FIFOMailBox_TypeDef; - -/** - * @brief Controller Area Network FilterRegister - */ - -typedef struct -{ - __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ - __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ -} CAN_FilterRegister_TypeDef; - -/** - * @brief Controller Area Network - */ - -typedef struct -{ - __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ - __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ - __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ - __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ - __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ - __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ - __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ - __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ - uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ - CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ - CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ - uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ - __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ - __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ - uint32_t RESERVED2; /*!< Reserved, 0x208 */ - __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ - uint32_t RESERVED3; /*!< Reserved, 0x210 */ - __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ - uint32_t RESERVED4; /*!< Reserved, 0x218 */ - __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ - uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ - CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ -} CAN_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Digital to Analog Converter - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ - __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ - __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ - __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ - __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ - __IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */ - __IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */ - __IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */ - __IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */ - __IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */ - __IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */ - __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ - __IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */ - __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ -} DAC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - -/** - * @brief DCMI - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DCMI control register 1, Address offset: 0x00 */ - __IO uint32_t SR; /*!< DCMI status register, Address offset: 0x04 */ - __IO uint32_t RISR; /*!< DCMI raw interrupt status register, Address offset: 0x08 */ - __IO uint32_t IER; /*!< DCMI interrupt enable register, Address offset: 0x0C */ - __IO uint32_t MISR; /*!< DCMI masked interrupt status register, Address offset: 0x10 */ - __IO uint32_t ICR; /*!< DCMI interrupt clear register, Address offset: 0x14 */ - __IO uint32_t ESCR; /*!< DCMI embedded synchronization code register, Address offset: 0x18 */ - __IO uint32_t ESUR; /*!< DCMI embedded synchronization unmask register, Address offset: 0x1C */ - __IO uint32_t CWSTRTR; /*!< DCMI crop window start, Address offset: 0x20 */ - __IO uint32_t CWSIZER; /*!< DCMI crop window size, Address offset: 0x24 */ - __IO uint32_t DR; /*!< DCMI data register, Address offset: 0x28 */ -} DCMI_TypeDef; - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - -/** - * @brief DMA2D Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA2D Control Register, Address offset: 0x00 */ - __IO uint32_t ISR; /*!< DMA2D Interrupt Status Register, Address offset: 0x04 */ - __IO uint32_t IFCR; /*!< DMA2D Interrupt Flag Clear Register, Address offset: 0x08 */ - __IO uint32_t FGMAR; /*!< DMA2D Foreground Memory Address Register, Address offset: 0x0C */ - __IO uint32_t FGOR; /*!< DMA2D Foreground Offset Register, Address offset: 0x10 */ - __IO uint32_t BGMAR; /*!< DMA2D Background Memory Address Register, Address offset: 0x14 */ - __IO uint32_t BGOR; /*!< DMA2D Background Offset Register, Address offset: 0x18 */ - __IO uint32_t FGPFCCR; /*!< DMA2D Foreground PFC Control Register, Address offset: 0x1C */ - __IO uint32_t FGCOLR; /*!< DMA2D Foreground Color Register, Address offset: 0x20 */ - __IO uint32_t BGPFCCR; /*!< DMA2D Background PFC Control Register, Address offset: 0x24 */ - __IO uint32_t BGCOLR; /*!< DMA2D Background Color Register, Address offset: 0x28 */ - __IO uint32_t FGCMAR; /*!< DMA2D Foreground CLUT Memory Address Register, Address offset: 0x2C */ - __IO uint32_t BGCMAR; /*!< DMA2D Background CLUT Memory Address Register, Address offset: 0x30 */ - __IO uint32_t OPFCCR; /*!< DMA2D Output PFC Control Register, Address offset: 0x34 */ - __IO uint32_t OCOLR; /*!< DMA2D Output Color Register, Address offset: 0x38 */ - __IO uint32_t OMAR; /*!< DMA2D Output Memory Address Register, Address offset: 0x3C */ - __IO uint32_t OOR; /*!< DMA2D Output Offset Register, Address offset: 0x40 */ - __IO uint32_t NLR; /*!< DMA2D Number of Line Register, Address offset: 0x44 */ - __IO uint32_t LWR; /*!< DMA2D Line Watermark Register, Address offset: 0x48 */ - __IO uint32_t AMTCR; /*!< DMA2D AHB Master Timer Configuration Register, Address offset: 0x4C */ - uint32_t RESERVED[236]; /*!< Reserved, 0x50-0x3FF */ - __IO uint32_t FGCLUT[256]; /*!< DMA2D Foreground CLUT, Address offset:400-7FF */ - __IO uint32_t BGCLUT[256]; /*!< DMA2D Background CLUT, Address offset:800-BFF */ -} DMA2D_TypeDef; - -/** - * @brief Ethernet MAC - */ - -typedef struct -{ - __IO uint32_t MACCR; - __IO uint32_t MACFFR; - __IO uint32_t MACHTHR; - __IO uint32_t MACHTLR; - __IO uint32_t MACMIIAR; - __IO uint32_t MACMIIDR; - __IO uint32_t MACFCR; - __IO uint32_t MACVLANTR; /* 8 */ - uint32_t RESERVED0[2]; - __IO uint32_t MACRWUFFR; /* 11 */ - __IO uint32_t MACPMTCSR; - uint32_t RESERVED1[2]; - __IO uint32_t MACSR; /* 15 */ - __IO uint32_t MACIMR; - __IO uint32_t MACA0HR; - __IO uint32_t MACA0LR; - __IO uint32_t MACA1HR; - __IO uint32_t MACA1LR; - __IO uint32_t MACA2HR; - __IO uint32_t MACA2LR; - __IO uint32_t MACA3HR; - __IO uint32_t MACA3LR; /* 24 */ - uint32_t RESERVED2[40]; - __IO uint32_t MMCCR; /* 65 */ - __IO uint32_t MMCRIR; - __IO uint32_t MMCTIR; - __IO uint32_t MMCRIMR; - __IO uint32_t MMCTIMR; /* 69 */ - uint32_t RESERVED3[14]; - __IO uint32_t MMCTGFSCCR; /* 84 */ - __IO uint32_t MMCTGFMSCCR; - uint32_t RESERVED4[5]; - __IO uint32_t MMCTGFCR; - uint32_t RESERVED5[10]; - __IO uint32_t MMCRFCECR; - __IO uint32_t MMCRFAECR; - uint32_t RESERVED6[10]; - __IO uint32_t MMCRGUFCR; - uint32_t RESERVED7[334]; - __IO uint32_t PTPTSCR; - __IO uint32_t PTPSSIR; - __IO uint32_t PTPTSHR; - __IO uint32_t PTPTSLR; - __IO uint32_t PTPTSHUR; - __IO uint32_t PTPTSLUR; - __IO uint32_t PTPTSAR; - __IO uint32_t PTPTTHR; - __IO uint32_t PTPTTLR; - __IO uint32_t RESERVED8; - __IO uint32_t PTPTSSR; - uint32_t RESERVED9[565]; - __IO uint32_t DMABMR; - __IO uint32_t DMATPDR; - __IO uint32_t DMARPDR; - __IO uint32_t DMARDLAR; - __IO uint32_t DMATDLAR; - __IO uint32_t DMASR; - __IO uint32_t DMAOMR; - __IO uint32_t DMAIER; - __IO uint32_t DMAMFBOCR; - __IO uint32_t DMARSWTR; - uint32_t RESERVED10[8]; - __IO uint32_t DMACHTDR; - __IO uint32_t DMACHRDR; - __IO uint32_t DMACHTBAR; - __IO uint32_t DMACHRBAR; -} ETH_TypeDef; - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief Flexible Memory Controller - */ - -typedef struct -{ - __IO uint32_t BTCR[8]; /*!< NOR/PSRAM chip-select control register(BCR) and chip-select timing register(BTR), Address offset: 0x00-1C */ -} FMC_Bank1_TypeDef; - -/** - * @brief Flexible Memory Controller Bank1E - */ - -typedef struct -{ - __IO uint32_t BWTR[7]; /*!< NOR/PSRAM write timing registers, Address offset: 0x104-0x11C */ -} FMC_Bank1E_TypeDef; - -/** - * @brief Flexible Memory Controller Bank2 - */ - -typedef struct -{ - __IO uint32_t PCR2; /*!< NAND Flash control register 2, Address offset: 0x60 */ - __IO uint32_t SR2; /*!< NAND Flash FIFO status and interrupt register 2, Address offset: 0x64 */ - __IO uint32_t PMEM2; /*!< NAND Flash Common memory space timing register 2, Address offset: 0x68 */ - __IO uint32_t PATT2; /*!< NAND Flash Attribute memory space timing register 2, Address offset: 0x6C */ - uint32_t RESERVED0; /*!< Reserved, 0x70 */ - __IO uint32_t ECCR2; /*!< NAND Flash ECC result registers 2, Address offset: 0x74 */ - uint32_t RESERVED1; /*!< Reserved, 0x78 */ - uint32_t RESERVED2; /*!< Reserved, 0x7C */ - __IO uint32_t PCR3; /*!< NAND Flash control register 3, Address offset: 0x80 */ - __IO uint32_t SR3; /*!< NAND Flash FIFO status and interrupt register 3, Address offset: 0x84 */ - __IO uint32_t PMEM3; /*!< NAND Flash Common memory space timing register 3, Address offset: 0x88 */ - __IO uint32_t PATT3; /*!< NAND Flash Attribute memory space timing register 3, Address offset: 0x8C */ - uint32_t RESERVED3; /*!< Reserved, 0x90 */ - __IO uint32_t ECCR3; /*!< NAND Flash ECC result registers 3, Address offset: 0x94 */ -} FMC_Bank2_3_TypeDef; - -/** - * @brief Flexible Memory Controller Bank4 - */ - -typedef struct -{ - __IO uint32_t PCR4; /*!< PC Card control register 4, Address offset: 0xA0 */ - __IO uint32_t SR4; /*!< PC Card FIFO status and interrupt register 4, Address offset: 0xA4 */ - __IO uint32_t PMEM4; /*!< PC Card Common memory space timing register 4, Address offset: 0xA8 */ - __IO uint32_t PATT4; /*!< PC Card Attribute memory space timing register 4, Address offset: 0xAC */ - __IO uint32_t PIO4; /*!< PC Card I/O space timing register 4, Address offset: 0xB0 */ -} FMC_Bank4_TypeDef; - -/** - * @brief Flexible Memory Controller Bank5_6 - */ - -typedef struct -{ - __IO uint32_t SDCR[2]; /*!< SDRAM Control registers , Address offset: 0x140-0x144 */ - __IO uint32_t SDTR[2]; /*!< SDRAM Timing registers , Address offset: 0x148-0x14C */ - __IO uint32_t SDCMR; /*!< SDRAM Command Mode register, Address offset: 0x150 */ - __IO uint32_t SDRTR; /*!< SDRAM Refresh Timer register, Address offset: 0x154 */ - __IO uint32_t SDSR; /*!< SDRAM Status register, Address offset: 0x158 */ -} FMC_Bank5_6_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - __IO uint32_t PLLSAICFGR; /*!< RCC PLLSAI configuration register, Address offset: 0x88 */ - __IO uint32_t DCKCFGR; /*!< RCC Dedicated Clocks configuration register, Address offset: 0x8C */ - -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - -/** - * @brief Serial Audio Interface - */ - -typedef struct -{ - __IO uint32_t GCR; /*!< SAI global configuration register, Address offset: 0x00 */ -} SAI_TypeDef; - -typedef struct -{ - __IO uint32_t CR1; /*!< SAI block x configuration register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< SAI block x configuration register 2, Address offset: 0x08 */ - __IO uint32_t FRCR; /*!< SAI block x frame configuration register, Address offset: 0x0C */ - __IO uint32_t SLOTR; /*!< SAI block x slot register, Address offset: 0x10 */ - __IO uint32_t IMR; /*!< SAI block x interrupt mask register, Address offset: 0x14 */ - __IO uint32_t SR; /*!< SAI block x status register, Address offset: 0x18 */ - __IO uint32_t CLRFR; /*!< SAI block x clear flag register, Address offset: 0x1C */ - __IO uint32_t DR; /*!< SAI block x data register, Address offset: 0x20 */ -} SAI_Block_TypeDef; - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - -/** - * @brief __USB_OTG_Core_register - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register 000h */ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register 004h */ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register 008h */ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register 00Ch */ - __IO uint32_t GRSTCTL; /*!< Core Reset Register 010h */ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register 014h */ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register 018h */ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register 01Ch */ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register 020h */ - __IO uint32_t GRXFSIZ; /* Receive FIFO Size Register 024h */ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register 028h*/ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg 02Ch */ - uint32_t Reserved30[2]; /* Reserved 030h*/ - __IO uint32_t GCCFG; /* General Purpose IO Register 038h*/ - __IO uint32_t CID; /* User ID Register 03Ch*/ - uint32_t Reserved40[48]; /* Reserved 040h-0FFh*/ - __IO uint32_t HPTXFSIZ; /* Host Periodic Tx FIFO Size Reg 100h*/ - __IO uint32_t DIEPTXF[0x0F];/* dev Periodic Transmit FIFO */ -} -USB_OTG_GlobalTypeDef; - - -/** - * @brief __device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /* dev Configuration Register 800h*/ - __IO uint32_t DCTL; /* dev Control Register 804h*/ - __IO uint32_t DSTS; /* dev Status Register (RO) 808h*/ - uint32_t Reserved0C; /* Reserved 80Ch*/ - __IO uint32_t DIEPMSK; /* dev IN Endpoint Mask 810h*/ - __IO uint32_t DOEPMSK; /* dev OUT Endpoint Mask 814h*/ - __IO uint32_t DAINT; /* dev All Endpoints Itr Reg 818h*/ - __IO uint32_t DAINTMSK; /* dev All Endpoints Itr Mask 81Ch*/ - uint32_t Reserved20; /* Reserved 820h*/ - uint32_t Reserved9; /* Reserved 824h*/ - __IO uint32_t DVBUSDIS; /* dev VBUS discharge Register 828h*/ - __IO uint32_t DVBUSPULSE; /* dev VBUS Pulse Register 82Ch*/ - __IO uint32_t DTHRCTL; /* dev thr 830h*/ - __IO uint32_t DIEPEMPMSK; /* dev empty msk 834h*/ - __IO uint32_t DEACHINT; /* dedicated EP interrupt 838h*/ - __IO uint32_t DEACHMSK; /* dedicated EP msk 83Ch*/ - uint32_t Reserved40; /* dedicated EP mask 840h*/ - __IO uint32_t DINEP1MSK; /* dedicated EP mask 844h*/ - uint32_t Reserved44[15]; /* Reserved 844-87Ch*/ - __IO uint32_t DOUTEP1MSK; /* dedicated EP msk 884h*/ -} -USB_OTG_DeviceTypeDef; - - -/** - * @brief __IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /* dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved 900h + (ep_num * 20h) + 04h*/ - __IO uint32_t DIEPINT; /* dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved 900h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DIEPTSIZ; /* IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h*/ - __IO uint32_t DIEPDMA; /* IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h*/ - __IO uint32_t DTXFSTS;/*IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h*/ - uint32_t Reserved18; /* Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch*/ -} -USB_OTG_INEndpointTypeDef; - - -/** - * @brief __OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /* dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved B00h + (ep_num * 20h) + 04h*/ - __IO uint32_t DOEPINT; /* dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved B00h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DOEPTSIZ; /* dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h*/ - __IO uint32_t DOEPDMA; /* dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h*/ - uint32_t Reserved18[2]; /* Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch*/ -} -USB_OTG_OUTEndpointTypeDef; - - -/** - * @brief __Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /* Host Configuration Register 400h*/ - __IO uint32_t HFIR; /* Host Frame Interval Register 404h*/ - __IO uint32_t HFNUM; /* Host Frame Nbr/Frame Remaining 408h*/ - uint32_t Reserved40C; /* Reserved 40Ch*/ - __IO uint32_t HPTXSTS; /* Host Periodic Tx FIFO/ Queue Status 410h*/ - __IO uint32_t HAINT; /* Host All Channels Interrupt Register 414h*/ - __IO uint32_t HAINTMSK; /* Host All Channels Interrupt Mask 418h*/ -} -USB_OTG_HostTypeDef; - -/** - * @brief __Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; - __IO uint32_t HCSPLT; - __IO uint32_t HCINT; - __IO uint32_t HCINTMSK; - __IO uint32_t HCTSIZ; - __IO uint32_t HCDMA; - uint32_t Reserved[2]; -} -USB_OTG_HostChannelTypeDef; -/** - * @} - */ - -/** @addtogroup Peripheral_memory_map - * @{ - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 2 MB) base address in the alias region */ -#define CCMDATARAM_BASE 0x10000000U /*!< CCM(core coupled memory) data RAM(64 KB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(112 KB) base address in the alias region */ -#define SRAM2_BASE 0x2001C000U /*!< SRAM2(16 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define BKPSRAM_BASE 0x40024000U /*!< Backup SRAM(4 KB) base address in the alias region */ -#define FMC_R_BASE 0xA0000000U /*!< FMC registers base address */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(112 KB) base address in the bit-band region */ -#define SRAM2_BB_BASE 0x22380000U /*!< SRAM2(16 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define BKPSRAM_BB_BASE 0x42480000U /*!< Backup SRAM(4 KB) base address in the bit-band region */ -#define FLASH_END 0x081FFFFFU /*!< FLASH end address */ -#define CCMDATARAM_END 0x1000FFFFU /*!< CCM data RAM end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define TIM7_BASE (APB1PERIPH_BASE + 0x1400U) -#define TIM12_BASE (APB1PERIPH_BASE + 0x1800U) -#define TIM13_BASE (APB1PERIPH_BASE + 0x1C00U) -#define TIM14_BASE (APB1PERIPH_BASE + 0x2000U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define USART3_BASE (APB1PERIPH_BASE + 0x4800U) -#define UART4_BASE (APB1PERIPH_BASE + 0x4C00U) -#define UART5_BASE (APB1PERIPH_BASE + 0x5000U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define CAN1_BASE (APB1PERIPH_BASE + 0x6400U) -#define CAN2_BASE (APB1PERIPH_BASE + 0x6800U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) -#define DAC_BASE (APB1PERIPH_BASE + 0x7400U) -#define UART7_BASE (APB1PERIPH_BASE + 0x7800U) -#define UART8_BASE (APB1PERIPH_BASE + 0x7C00U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define TIM8_BASE (APB2PERIPH_BASE + 0x0400U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC2_BASE (APB2PERIPH_BASE + 0x2100U) -#define ADC3_BASE (APB2PERIPH_BASE + 0x2200U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SPI4_BASE (APB2PERIPH_BASE + 0x3400U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) -#define SPI5_BASE (APB2PERIPH_BASE + 0x5000U) -#define SPI6_BASE (APB2PERIPH_BASE + 0x5400U) -#define SAI1_BASE (APB2PERIPH_BASE + 0x5800U) -#define SAI1_Block_A_BASE (SAI1_BASE + 0x004U) -#define SAI1_Block_B_BASE (SAI1_BASE + 0x024U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOF_BASE (AHB1PERIPH_BASE + 0x1400U) -#define GPIOG_BASE (AHB1PERIPH_BASE + 0x1800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define GPIOI_BASE (AHB1PERIPH_BASE + 0x2000U) -#define GPIOJ_BASE (AHB1PERIPH_BASE + 0x2400U) -#define GPIOK_BASE (AHB1PERIPH_BASE + 0x2800U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) -#define ETH_BASE (AHB1PERIPH_BASE + 0x8000U) -#define ETH_MAC_BASE (ETH_BASE) -#define ETH_MMC_BASE (ETH_BASE + 0x0100U) -#define ETH_PTP_BASE (ETH_BASE + 0x0700U) -#define ETH_DMA_BASE (ETH_BASE + 0x1000U) -#define DMA2D_BASE (AHB1PERIPH_BASE + 0xB000U) - -/*!< AHB2 peripherals */ -#define DCMI_BASE (AHB2PERIPH_BASE + 0x50000U) -#define RNG_BASE (AHB2PERIPH_BASE + 0x60800U) - -/*!< FMC Bankx registers base address */ -#define FMC_Bank1_R_BASE (FMC_R_BASE + 0x0000U) -#define FMC_Bank1E_R_BASE (FMC_R_BASE + 0x0104U) -#define FMC_Bank2_3_R_BASE (FMC_R_BASE + 0x0060U) -#define FMC_Bank4_R_BASE (FMC_R_BASE + 0x00A0U) -#define FMC_Bank5_6_R_BASE (FMC_R_BASE + 0x0140U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_HS_PERIPH_BASE 0x40040000U -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define TIM7 ((TIM_TypeDef *) TIM7_BASE) -#define TIM12 ((TIM_TypeDef *) TIM12_BASE) -#define TIM13 ((TIM_TypeDef *) TIM13_BASE) -#define TIM14 ((TIM_TypeDef *) TIM14_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define USART3 ((USART_TypeDef *) USART3_BASE) -#define UART4 ((USART_TypeDef *) UART4_BASE) -#define UART5 ((USART_TypeDef *) UART5_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define CAN1 ((CAN_TypeDef *) CAN1_BASE) -#define CAN2 ((CAN_TypeDef *) CAN2_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define DAC ((DAC_TypeDef *) DAC_BASE) -#define UART7 ((USART_TypeDef *) UART7_BASE) -#define UART8 ((USART_TypeDef *) UART8_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define TIM8 ((TIM_TypeDef *) TIM8_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define ADC2 ((ADC_TypeDef *) ADC2_BASE) -#define ADC3 ((ADC_TypeDef *) ADC3_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SPI4 ((SPI_TypeDef *) SPI4_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define SPI5 ((SPI_TypeDef *) SPI5_BASE) -#define SPI6 ((SPI_TypeDef *) SPI6_BASE) -#define SAI1 ((SAI_TypeDef *) SAI1_BASE) -#define SAI1_Block_A ((SAI_Block_TypeDef *)SAI1_Block_A_BASE) -#define SAI1_Block_B ((SAI_Block_TypeDef *)SAI1_Block_B_BASE) - -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOF ((GPIO_TypeDef *) GPIOF_BASE) -#define GPIOG ((GPIO_TypeDef *) GPIOG_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define GPIOI ((GPIO_TypeDef *) GPIOI_BASE) -#define GPIOJ ((GPIO_TypeDef *) GPIOJ_BASE) -#define GPIOK ((GPIO_TypeDef *) GPIOK_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define ETH ((ETH_TypeDef *) ETH_BASE) -#define DMA2D ((DMA2D_TypeDef *)DMA2D_BASE) -#define DCMI ((DCMI_TypeDef *) DCMI_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) -#define FMC_Bank1 ((FMC_Bank1_TypeDef *) FMC_Bank1_R_BASE) -#define FMC_Bank1E ((FMC_Bank1E_TypeDef *) FMC_Bank1E_R_BASE) -#define FMC_Bank2_3 ((FMC_Bank2_3_TypeDef *) FMC_Bank2_3_R_BASE) -#define FMC_Bank4 ((FMC_Bank4_TypeDef *) FMC_Bank4_R_BASE) -#define FMC_Bank5_6 ((FMC_Bank5_6_TypeDef *) FMC_Bank5_6_R_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) -#define USB_OTG_HS ((USB_OTG_GlobalTypeDef *) USB_OTG_HS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS_Device - * @{ - */ - -/** @addtogroup stm32f429xx - * @{ - */ - -#ifndef __STM32F429xx_H -#define __STM32F429xx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1, ADC2 and ADC3 global Interrupts */ - CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */ - CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */ - CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ - CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - USART3_IRQn = 39, /*!< USART3 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */ - TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */ - TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */ - TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare Interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - FMC_IRQn = 48, /*!< FMC global Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - UART4_IRQn = 52, /*!< UART4 global Interrupt */ - UART5_IRQn = 53, /*!< UART5 global Interrupt */ - TIM6_DAC_IRQn = 54, /*!< TIM6 global and DAC1&2 underrun error interrupts */ - TIM7_IRQn = 55, /*!< TIM7 global interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - ETH_IRQn = 61, /*!< Ethernet global Interrupt */ - ETH_WKUP_IRQn = 62, /*!< Ethernet Wakeup through EXTI line Interrupt */ - CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */ - CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */ - CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */ - CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - OTG_HS_EP1_OUT_IRQn = 74, /*!< USB OTG HS End Point 1 Out global interrupt */ - OTG_HS_EP1_IN_IRQn = 75, /*!< USB OTG HS End Point 1 In global interrupt */ - OTG_HS_WKUP_IRQn = 76, /*!< USB OTG HS Wakeup through EXTI interrupt */ - OTG_HS_IRQn = 77, /*!< USB OTG HS global interrupt */ - DCMI_IRQn = 78, /*!< DCMI global interrupt */ - HASH_RNG_IRQn = 80, /*!< Hash and RNG global interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - UART7_IRQn = 82, /*!< UART7 global interrupt */ - UART8_IRQn = 83, /*!< UART8 global interrupt */ - SPI4_IRQn = 84, /*!< SPI4 global Interrupt */ - SPI5_IRQn = 85, /*!< SPI5 global Interrupt */ - SPI6_IRQn = 86, /*!< SPI6 global Interrupt */ - SAI1_IRQn = 87, /*!< SAI1 global Interrupt */ - LTDC_IRQn = 88, /*!< LTDC global Interrupt */ - LTDC_ER_IRQn = 89, /*!< LTDC Error global Interrupt */ - DMA2D_IRQn = 90 /*!< DMA2D global Interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - - -/** - * @brief Controller Area Network TxMailBox - */ - -typedef struct -{ - __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ - __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ - __IO uint32_t TDLR; /*!< CAN mailbox data low register */ - __IO uint32_t TDHR; /*!< CAN mailbox data high register */ -} CAN_TxMailBox_TypeDef; - -/** - * @brief Controller Area Network FIFOMailBox - */ - -typedef struct -{ - __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ - __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ - __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ - __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ -} CAN_FIFOMailBox_TypeDef; - -/** - * @brief Controller Area Network FilterRegister - */ - -typedef struct -{ - __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ - __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ -} CAN_FilterRegister_TypeDef; - -/** - * @brief Controller Area Network - */ - -typedef struct -{ - __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ - __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ - __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ - __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ - __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ - __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ - __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ - __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ - uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ - CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ - CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ - uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ - __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ - __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ - uint32_t RESERVED2; /*!< Reserved, 0x208 */ - __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ - uint32_t RESERVED3; /*!< Reserved, 0x210 */ - __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ - uint32_t RESERVED4; /*!< Reserved, 0x218 */ - __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ - uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ - CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ -} CAN_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Digital to Analog Converter - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ - __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ - __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ - __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ - __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ - __IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */ - __IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */ - __IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */ - __IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */ - __IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */ - __IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */ - __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ - __IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */ - __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ -} DAC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - -/** - * @brief DCMI - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DCMI control register 1, Address offset: 0x00 */ - __IO uint32_t SR; /*!< DCMI status register, Address offset: 0x04 */ - __IO uint32_t RISR; /*!< DCMI raw interrupt status register, Address offset: 0x08 */ - __IO uint32_t IER; /*!< DCMI interrupt enable register, Address offset: 0x0C */ - __IO uint32_t MISR; /*!< DCMI masked interrupt status register, Address offset: 0x10 */ - __IO uint32_t ICR; /*!< DCMI interrupt clear register, Address offset: 0x14 */ - __IO uint32_t ESCR; /*!< DCMI embedded synchronization code register, Address offset: 0x18 */ - __IO uint32_t ESUR; /*!< DCMI embedded synchronization unmask register, Address offset: 0x1C */ - __IO uint32_t CWSTRTR; /*!< DCMI crop window start, Address offset: 0x20 */ - __IO uint32_t CWSIZER; /*!< DCMI crop window size, Address offset: 0x24 */ - __IO uint32_t DR; /*!< DCMI data register, Address offset: 0x28 */ -} DCMI_TypeDef; - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - -/** - * @brief DMA2D Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA2D Control Register, Address offset: 0x00 */ - __IO uint32_t ISR; /*!< DMA2D Interrupt Status Register, Address offset: 0x04 */ - __IO uint32_t IFCR; /*!< DMA2D Interrupt Flag Clear Register, Address offset: 0x08 */ - __IO uint32_t FGMAR; /*!< DMA2D Foreground Memory Address Register, Address offset: 0x0C */ - __IO uint32_t FGOR; /*!< DMA2D Foreground Offset Register, Address offset: 0x10 */ - __IO uint32_t BGMAR; /*!< DMA2D Background Memory Address Register, Address offset: 0x14 */ - __IO uint32_t BGOR; /*!< DMA2D Background Offset Register, Address offset: 0x18 */ - __IO uint32_t FGPFCCR; /*!< DMA2D Foreground PFC Control Register, Address offset: 0x1C */ - __IO uint32_t FGCOLR; /*!< DMA2D Foreground Color Register, Address offset: 0x20 */ - __IO uint32_t BGPFCCR; /*!< DMA2D Background PFC Control Register, Address offset: 0x24 */ - __IO uint32_t BGCOLR; /*!< DMA2D Background Color Register, Address offset: 0x28 */ - __IO uint32_t FGCMAR; /*!< DMA2D Foreground CLUT Memory Address Register, Address offset: 0x2C */ - __IO uint32_t BGCMAR; /*!< DMA2D Background CLUT Memory Address Register, Address offset: 0x30 */ - __IO uint32_t OPFCCR; /*!< DMA2D Output PFC Control Register, Address offset: 0x34 */ - __IO uint32_t OCOLR; /*!< DMA2D Output Color Register, Address offset: 0x38 */ - __IO uint32_t OMAR; /*!< DMA2D Output Memory Address Register, Address offset: 0x3C */ - __IO uint32_t OOR; /*!< DMA2D Output Offset Register, Address offset: 0x40 */ - __IO uint32_t NLR; /*!< DMA2D Number of Line Register, Address offset: 0x44 */ - __IO uint32_t LWR; /*!< DMA2D Line Watermark Register, Address offset: 0x48 */ - __IO uint32_t AMTCR; /*!< DMA2D AHB Master Timer Configuration Register, Address offset: 0x4C */ - uint32_t RESERVED[236]; /*!< Reserved, 0x50-0x3FF */ - __IO uint32_t FGCLUT[256]; /*!< DMA2D Foreground CLUT, Address offset:400-7FF */ - __IO uint32_t BGCLUT[256]; /*!< DMA2D Background CLUT, Address offset:800-BFF */ -} DMA2D_TypeDef; - -/** - * @brief Ethernet MAC - */ - -typedef struct -{ - __IO uint32_t MACCR; - __IO uint32_t MACFFR; - __IO uint32_t MACHTHR; - __IO uint32_t MACHTLR; - __IO uint32_t MACMIIAR; - __IO uint32_t MACMIIDR; - __IO uint32_t MACFCR; - __IO uint32_t MACVLANTR; /* 8 */ - uint32_t RESERVED0[2]; - __IO uint32_t MACRWUFFR; /* 11 */ - __IO uint32_t MACPMTCSR; - uint32_t RESERVED1[2]; - __IO uint32_t MACSR; /* 15 */ - __IO uint32_t MACIMR; - __IO uint32_t MACA0HR; - __IO uint32_t MACA0LR; - __IO uint32_t MACA1HR; - __IO uint32_t MACA1LR; - __IO uint32_t MACA2HR; - __IO uint32_t MACA2LR; - __IO uint32_t MACA3HR; - __IO uint32_t MACA3LR; /* 24 */ - uint32_t RESERVED2[40]; - __IO uint32_t MMCCR; /* 65 */ - __IO uint32_t MMCRIR; - __IO uint32_t MMCTIR; - __IO uint32_t MMCRIMR; - __IO uint32_t MMCTIMR; /* 69 */ - uint32_t RESERVED3[14]; - __IO uint32_t MMCTGFSCCR; /* 84 */ - __IO uint32_t MMCTGFMSCCR; - uint32_t RESERVED4[5]; - __IO uint32_t MMCTGFCR; - uint32_t RESERVED5[10]; - __IO uint32_t MMCRFCECR; - __IO uint32_t MMCRFAECR; - uint32_t RESERVED6[10]; - __IO uint32_t MMCRGUFCR; - uint32_t RESERVED7[334]; - __IO uint32_t PTPTSCR; - __IO uint32_t PTPSSIR; - __IO uint32_t PTPTSHR; - __IO uint32_t PTPTSLR; - __IO uint32_t PTPTSHUR; - __IO uint32_t PTPTSLUR; - __IO uint32_t PTPTSAR; - __IO uint32_t PTPTTHR; - __IO uint32_t PTPTTLR; - __IO uint32_t RESERVED8; - __IO uint32_t PTPTSSR; - uint32_t RESERVED9[565]; - __IO uint32_t DMABMR; - __IO uint32_t DMATPDR; - __IO uint32_t DMARPDR; - __IO uint32_t DMARDLAR; - __IO uint32_t DMATDLAR; - __IO uint32_t DMASR; - __IO uint32_t DMAOMR; - __IO uint32_t DMAIER; - __IO uint32_t DMAMFBOCR; - __IO uint32_t DMARSWTR; - uint32_t RESERVED10[8]; - __IO uint32_t DMACHTDR; - __IO uint32_t DMACHRDR; - __IO uint32_t DMACHTBAR; - __IO uint32_t DMACHRBAR; -} ETH_TypeDef; - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief Flexible Memory Controller - */ - -typedef struct -{ - __IO uint32_t BTCR[8]; /*!< NOR/PSRAM chip-select control register(BCR) and chip-select timing register(BTR), Address offset: 0x00-1C */ -} FMC_Bank1_TypeDef; - -/** - * @brief Flexible Memory Controller Bank1E - */ - -typedef struct -{ - __IO uint32_t BWTR[7]; /*!< NOR/PSRAM write timing registers, Address offset: 0x104-0x11C */ -} FMC_Bank1E_TypeDef; - -/** - * @brief Flexible Memory Controller Bank2 - */ - -typedef struct -{ - __IO uint32_t PCR2; /*!< NAND Flash control register 2, Address offset: 0x60 */ - __IO uint32_t SR2; /*!< NAND Flash FIFO status and interrupt register 2, Address offset: 0x64 */ - __IO uint32_t PMEM2; /*!< NAND Flash Common memory space timing register 2, Address offset: 0x68 */ - __IO uint32_t PATT2; /*!< NAND Flash Attribute memory space timing register 2, Address offset: 0x6C */ - uint32_t RESERVED0; /*!< Reserved, 0x70 */ - __IO uint32_t ECCR2; /*!< NAND Flash ECC result registers 2, Address offset: 0x74 */ - uint32_t RESERVED1; /*!< Reserved, 0x78 */ - uint32_t RESERVED2; /*!< Reserved, 0x7C */ - __IO uint32_t PCR3; /*!< NAND Flash control register 3, Address offset: 0x80 */ - __IO uint32_t SR3; /*!< NAND Flash FIFO status and interrupt register 3, Address offset: 0x84 */ - __IO uint32_t PMEM3; /*!< NAND Flash Common memory space timing register 3, Address offset: 0x88 */ - __IO uint32_t PATT3; /*!< NAND Flash Attribute memory space timing register 3, Address offset: 0x8C */ - uint32_t RESERVED3; /*!< Reserved, 0x90 */ - __IO uint32_t ECCR3; /*!< NAND Flash ECC result registers 3, Address offset: 0x94 */ -} FMC_Bank2_3_TypeDef; - -/** - * @brief Flexible Memory Controller Bank4 - */ - -typedef struct -{ - __IO uint32_t PCR4; /*!< PC Card control register 4, Address offset: 0xA0 */ - __IO uint32_t SR4; /*!< PC Card FIFO status and interrupt register 4, Address offset: 0xA4 */ - __IO uint32_t PMEM4; /*!< PC Card Common memory space timing register 4, Address offset: 0xA8 */ - __IO uint32_t PATT4; /*!< PC Card Attribute memory space timing register 4, Address offset: 0xAC */ - __IO uint32_t PIO4; /*!< PC Card I/O space timing register 4, Address offset: 0xB0 */ -} FMC_Bank4_TypeDef; - -/** - * @brief Flexible Memory Controller Bank5_6 - */ - -typedef struct -{ - __IO uint32_t SDCR[2]; /*!< SDRAM Control registers , Address offset: 0x140-0x144 */ - __IO uint32_t SDTR[2]; /*!< SDRAM Timing registers , Address offset: 0x148-0x14C */ - __IO uint32_t SDCMR; /*!< SDRAM Command Mode register, Address offset: 0x150 */ - __IO uint32_t SDRTR; /*!< SDRAM Refresh Timer register, Address offset: 0x154 */ - __IO uint32_t SDSR; /*!< SDRAM Status register, Address offset: 0x158 */ -} FMC_Bank5_6_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief LCD-TFT Display Controller - */ - -typedef struct -{ - uint32_t RESERVED0[2]; /*!< Reserved, 0x00-0x04 */ - __IO uint32_t SSCR; /*!< LTDC Synchronization Size Configuration Register, Address offset: 0x08 */ - __IO uint32_t BPCR; /*!< LTDC Back Porch Configuration Register, Address offset: 0x0C */ - __IO uint32_t AWCR; /*!< LTDC Active Width Configuration Register, Address offset: 0x10 */ - __IO uint32_t TWCR; /*!< LTDC Total Width Configuration Register, Address offset: 0x14 */ - __IO uint32_t GCR; /*!< LTDC Global Control Register, Address offset: 0x18 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x1C-0x20 */ - __IO uint32_t SRCR; /*!< LTDC Shadow Reload Configuration Register, Address offset: 0x24 */ - uint32_t RESERVED2[1]; /*!< Reserved, 0x28 */ - __IO uint32_t BCCR; /*!< LTDC Background Color Configuration Register, Address offset: 0x2C */ - uint32_t RESERVED3[1]; /*!< Reserved, 0x30 */ - __IO uint32_t IER; /*!< LTDC Interrupt Enable Register, Address offset: 0x34 */ - __IO uint32_t ISR; /*!< LTDC Interrupt Status Register, Address offset: 0x38 */ - __IO uint32_t ICR; /*!< LTDC Interrupt Clear Register, Address offset: 0x3C */ - __IO uint32_t LIPCR; /*!< LTDC Line Interrupt Position Configuration Register, Address offset: 0x40 */ - __IO uint32_t CPSR; /*!< LTDC Current Position Status Register, Address offset: 0x44 */ - __IO uint32_t CDSR; /*!< LTDC Current Display Status Register, Address offset: 0x48 */ -} LTDC_TypeDef; - -/** - * @brief LCD-TFT Display layer x Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< LTDC Layerx Control Register Address offset: 0x84 */ - __IO uint32_t WHPCR; /*!< LTDC Layerx Window Horizontal Position Configuration Register Address offset: 0x88 */ - __IO uint32_t WVPCR; /*!< LTDC Layerx Window Vertical Position Configuration Register Address offset: 0x8C */ - __IO uint32_t CKCR; /*!< LTDC Layerx Color Keying Configuration Register Address offset: 0x90 */ - __IO uint32_t PFCR; /*!< LTDC Layerx Pixel Format Configuration Register Address offset: 0x94 */ - __IO uint32_t CACR; /*!< LTDC Layerx Constant Alpha Configuration Register Address offset: 0x98 */ - __IO uint32_t DCCR; /*!< LTDC Layerx Default Color Configuration Register Address offset: 0x9C */ - __IO uint32_t BFCR; /*!< LTDC Layerx Blending Factors Configuration Register Address offset: 0xA0 */ - uint32_t RESERVED0[2]; /*!< Reserved */ - __IO uint32_t CFBAR; /*!< LTDC Layerx Color Frame Buffer Address Register Address offset: 0xAC */ - __IO uint32_t CFBLR; /*!< LTDC Layerx Color Frame Buffer Length Register Address offset: 0xB0 */ - __IO uint32_t CFBLNR; /*!< LTDC Layerx ColorFrame Buffer Line Number Register Address offset: 0xB4 */ - uint32_t RESERVED1[3]; /*!< Reserved */ - __IO uint32_t CLUTWR; /*!< LTDC Layerx CLUT Write Register Address offset: 0x144 */ - -} LTDC_Layer_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - __IO uint32_t PLLSAICFGR; /*!< RCC PLLSAI configuration register, Address offset: 0x88 */ - __IO uint32_t DCKCFGR; /*!< RCC Dedicated Clocks configuration register, Address offset: 0x8C */ - -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - -/** - * @brief Serial Audio Interface - */ - -typedef struct -{ - __IO uint32_t GCR; /*!< SAI global configuration register, Address offset: 0x00 */ -} SAI_TypeDef; - -typedef struct -{ - __IO uint32_t CR1; /*!< SAI block x configuration register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< SAI block x configuration register 2, Address offset: 0x08 */ - __IO uint32_t FRCR; /*!< SAI block x frame configuration register, Address offset: 0x0C */ - __IO uint32_t SLOTR; /*!< SAI block x slot register, Address offset: 0x10 */ - __IO uint32_t IMR; /*!< SAI block x interrupt mask register, Address offset: 0x14 */ - __IO uint32_t SR; /*!< SAI block x status register, Address offset: 0x18 */ - __IO uint32_t CLRFR; /*!< SAI block x clear flag register, Address offset: 0x1C */ - __IO uint32_t DR; /*!< SAI block x data register, Address offset: 0x20 */ -} SAI_Block_TypeDef; - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - -/** - * @brief __USB_OTG_Core_register - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register 000h */ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register 004h */ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register 008h */ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register 00Ch */ - __IO uint32_t GRSTCTL; /*!< Core Reset Register 010h */ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register 014h */ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register 018h */ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register 01Ch */ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register 020h */ - __IO uint32_t GRXFSIZ; /* Receive FIFO Size Register 024h */ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register 028h*/ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg 02Ch */ - uint32_t Reserved30[2]; /* Reserved 030h*/ - __IO uint32_t GCCFG; /* General Purpose IO Register 038h*/ - __IO uint32_t CID; /* User ID Register 03Ch*/ - uint32_t Reserved40[48]; /* Reserved 040h-0FFh*/ - __IO uint32_t HPTXFSIZ; /* Host Periodic Tx FIFO Size Reg 100h*/ - __IO uint32_t DIEPTXF[0x0F];/* dev Periodic Transmit FIFO */ -} -USB_OTG_GlobalTypeDef; - - -/** - * @brief __device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /* dev Configuration Register 800h*/ - __IO uint32_t DCTL; /* dev Control Register 804h*/ - __IO uint32_t DSTS; /* dev Status Register (RO) 808h*/ - uint32_t Reserved0C; /* Reserved 80Ch*/ - __IO uint32_t DIEPMSK; /* dev IN Endpoint Mask 810h*/ - __IO uint32_t DOEPMSK; /* dev OUT Endpoint Mask 814h*/ - __IO uint32_t DAINT; /* dev All Endpoints Itr Reg 818h*/ - __IO uint32_t DAINTMSK; /* dev All Endpoints Itr Mask 81Ch*/ - uint32_t Reserved20; /* Reserved 820h*/ - uint32_t Reserved9; /* Reserved 824h*/ - __IO uint32_t DVBUSDIS; /* dev VBUS discharge Register 828h*/ - __IO uint32_t DVBUSPULSE; /* dev VBUS Pulse Register 82Ch*/ - __IO uint32_t DTHRCTL; /* dev thr 830h*/ - __IO uint32_t DIEPEMPMSK; /* dev empty msk 834h*/ - __IO uint32_t DEACHINT; /* dedicated EP interrupt 838h*/ - __IO uint32_t DEACHMSK; /* dedicated EP msk 83Ch*/ - uint32_t Reserved40; /* dedicated EP mask 840h*/ - __IO uint32_t DINEP1MSK; /* dedicated EP mask 844h*/ - uint32_t Reserved44[15]; /* Reserved 844-87Ch*/ - __IO uint32_t DOUTEP1MSK; /* dedicated EP msk 884h*/ -} -USB_OTG_DeviceTypeDef; - - -/** - * @brief __IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /* dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved 900h + (ep_num * 20h) + 04h*/ - __IO uint32_t DIEPINT; /* dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved 900h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DIEPTSIZ; /* IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h*/ - __IO uint32_t DIEPDMA; /* IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h*/ - __IO uint32_t DTXFSTS;/*IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h*/ - uint32_t Reserved18; /* Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch*/ -} -USB_OTG_INEndpointTypeDef; - - -/** - * @brief __OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /* dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved B00h + (ep_num * 20h) + 04h*/ - __IO uint32_t DOEPINT; /* dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved B00h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DOEPTSIZ; /* dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h*/ - __IO uint32_t DOEPDMA; /* dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h*/ - uint32_t Reserved18[2]; /* Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch*/ -} -USB_OTG_OUTEndpointTypeDef; - - -/** - * @brief __Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /* Host Configuration Register 400h*/ - __IO uint32_t HFIR; /* Host Frame Interval Register 404h*/ - __IO uint32_t HFNUM; /* Host Frame Nbr/Frame Remaining 408h*/ - uint32_t Reserved40C; /* Reserved 40Ch*/ - __IO uint32_t HPTXSTS; /* Host Periodic Tx FIFO/ Queue Status 410h*/ - __IO uint32_t HAINT; /* Host All Channels Interrupt Register 414h*/ - __IO uint32_t HAINTMSK; /* Host All Channels Interrupt Mask 418h*/ -} -USB_OTG_HostTypeDef; - -/** - * @brief __Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; - __IO uint32_t HCSPLT; - __IO uint32_t HCINT; - __IO uint32_t HCINTMSK; - __IO uint32_t HCTSIZ; - __IO uint32_t HCDMA; - uint32_t Reserved[2]; -} -USB_OTG_HostChannelTypeDef; -/** - * @} - */ - -/** @addtogroup Peripheral_memory_map - * @{ - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 2 MB) base address in the alias region */ -#define CCMDATARAM_BASE 0x10000000U /*!< CCM(core coupled memory) data RAM(64 KB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(112 KB) base address in the alias region */ -#define SRAM2_BASE 0x2001C000U /*!< SRAM2(16 KB) base address in the alias region */ -#define SRAM3_BASE 0x20020000U /*!< SRAM3(64 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define BKPSRAM_BASE 0x40024000U /*!< Backup SRAM(4 KB) base address in the alias region */ -#define FMC_R_BASE 0xA0000000U /*!< FMC registers base address */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(112 KB) base address in the bit-band region */ -#define SRAM2_BB_BASE 0x22380000U /*!< SRAM2(16 KB) base address in the bit-band region */ -#define SRAM3_BB_BASE 0x22400000U /*!< SRAM3(64 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define BKPSRAM_BB_BASE 0x42480000U /*!< Backup SRAM(4 KB) base address in the bit-band region */ -#define FLASH_END 0x081FFFFFU /*!< FLASH end address */ -#define CCMDATARAM_END 0x1000FFFFU /*!< CCM data RAM end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define TIM7_BASE (APB1PERIPH_BASE + 0x1400U) -#define TIM12_BASE (APB1PERIPH_BASE + 0x1800U) -#define TIM13_BASE (APB1PERIPH_BASE + 0x1C00U) -#define TIM14_BASE (APB1PERIPH_BASE + 0x2000U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define USART3_BASE (APB1PERIPH_BASE + 0x4800U) -#define UART4_BASE (APB1PERIPH_BASE + 0x4C00U) -#define UART5_BASE (APB1PERIPH_BASE + 0x5000U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define CAN1_BASE (APB1PERIPH_BASE + 0x6400U) -#define CAN2_BASE (APB1PERIPH_BASE + 0x6800U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) -#define DAC_BASE (APB1PERIPH_BASE + 0x7400U) -#define UART7_BASE (APB1PERIPH_BASE + 0x7800U) -#define UART8_BASE (APB1PERIPH_BASE + 0x7C00U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define TIM8_BASE (APB2PERIPH_BASE + 0x0400U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC2_BASE (APB2PERIPH_BASE + 0x2100U) -#define ADC3_BASE (APB2PERIPH_BASE + 0x2200U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SPI4_BASE (APB2PERIPH_BASE + 0x3400U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) -#define SPI5_BASE (APB2PERIPH_BASE + 0x5000U) -#define SPI6_BASE (APB2PERIPH_BASE + 0x5400U) -#define SAI1_BASE (APB2PERIPH_BASE + 0x5800U) -#define SAI1_Block_A_BASE (SAI1_BASE + 0x004U) -#define SAI1_Block_B_BASE (SAI1_BASE + 0x024U) -#define LTDC_BASE (APB2PERIPH_BASE + 0x6800U) -#define LTDC_Layer1_BASE (LTDC_BASE + 0x84U) -#define LTDC_Layer2_BASE (LTDC_BASE + 0x104U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOF_BASE (AHB1PERIPH_BASE + 0x1400U) -#define GPIOG_BASE (AHB1PERIPH_BASE + 0x1800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define GPIOI_BASE (AHB1PERIPH_BASE + 0x2000U) -#define GPIOJ_BASE (AHB1PERIPH_BASE + 0x2400U) -#define GPIOK_BASE (AHB1PERIPH_BASE + 0x2800U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) -#define ETH_BASE (AHB1PERIPH_BASE + 0x8000U) -#define ETH_MAC_BASE (ETH_BASE) -#define ETH_MMC_BASE (ETH_BASE + 0x0100U) -#define ETH_PTP_BASE (ETH_BASE + 0x0700U) -#define ETH_DMA_BASE (ETH_BASE + 0x1000U) -#define DMA2D_BASE (AHB1PERIPH_BASE + 0xB000U) - -/*!< AHB2 peripherals */ -#define DCMI_BASE (AHB2PERIPH_BASE + 0x50000U) -#define RNG_BASE (AHB2PERIPH_BASE + 0x60800U) - -/*!< FMC Bankx registers base address */ -#define FMC_Bank1_R_BASE (FMC_R_BASE + 0x0000U) -#define FMC_Bank1E_R_BASE (FMC_R_BASE + 0x0104U) -#define FMC_Bank2_3_R_BASE (FMC_R_BASE + 0x0060U) -#define FMC_Bank4_R_BASE (FMC_R_BASE + 0x00A0U) -#define FMC_Bank5_6_R_BASE (FMC_R_BASE + 0x0140U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_HS_PERIPH_BASE 0x40040000U -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define TIM7 ((TIM_TypeDef *) TIM7_BASE) -#define TIM12 ((TIM_TypeDef *) TIM12_BASE) -#define TIM13 ((TIM_TypeDef *) TIM13_BASE) -#define TIM14 ((TIM_TypeDef *) TIM14_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define USART3 ((USART_TypeDef *) USART3_BASE) -#define UART4 ((USART_TypeDef *) UART4_BASE) -#define UART5 ((USART_TypeDef *) UART5_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define CAN1 ((CAN_TypeDef *) CAN1_BASE) -#define CAN2 ((CAN_TypeDef *) CAN2_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define DAC ((DAC_TypeDef *) DAC_BASE) -#define UART7 ((USART_TypeDef *) UART7_BASE) -#define UART8 ((USART_TypeDef *) UART8_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define TIM8 ((TIM_TypeDef *) TIM8_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define ADC2 ((ADC_TypeDef *) ADC2_BASE) -#define ADC3 ((ADC_TypeDef *) ADC3_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SPI4 ((SPI_TypeDef *) SPI4_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define SPI5 ((SPI_TypeDef *) SPI5_BASE) -#define SPI6 ((SPI_TypeDef *) SPI6_BASE) -#define SAI1 ((SAI_TypeDef *) SAI1_BASE) -#define SAI1_Block_A ((SAI_Block_TypeDef *)SAI1_Block_A_BASE) -#define SAI1_Block_B ((SAI_Block_TypeDef *)SAI1_Block_B_BASE) -#define LTDC ((LTDC_TypeDef *)LTDC_BASE) -#define LTDC_Layer1 ((LTDC_Layer_TypeDef *)LTDC_Layer1_BASE) -#define LTDC_Layer2 ((LTDC_Layer_TypeDef *)LTDC_Layer2_BASE) - -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOF ((GPIO_TypeDef *) GPIOF_BASE) -#define GPIOG ((GPIO_TypeDef *) GPIOG_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define GPIOI ((GPIO_TypeDef *) GPIOI_BASE) -#define GPIOJ ((GPIO_TypeDef *) GPIOJ_BASE) -#define GPIOK ((GPIO_TypeDef *) GPIOK_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define ETH ((ETH_TypeDef *) ETH_BASE) -#define DMA2D ((DMA2D_TypeDef *)DMA2D_BASE) -#define DCMI ((DCMI_TypeDef *) DCMI_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) -#define FMC_Bank1 ((FMC_Bank1_TypeDef *) FMC_Bank1_R_BASE) -#define FMC_Bank1E ((FMC_Bank1E_TypeDef *) FMC_Bank1E_R_BASE) -#define FMC_Bank2_3 ((FMC_Bank2_3_TypeDef *) FMC_Bank2_3_R_BASE) -#define FMC_Bank4 ((FMC_Bank4_TypeDef *) FMC_Bank4_R_BASE) -#define FMC_Bank5_6 ((FMC_Bank5_6_TypeDef *) FMC_Bank5_6_R_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) -#define USB_OTG_HS ((USB_OTG_GlobalTypeDef *) USB_OTG_HS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS_Device - * @{ - */ - -/** @addtogroup stm32f437xx - * @{ - */ - -#ifndef __STM32F437xx_H -#define __STM32F437xx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1, ADC2 and ADC3 global Interrupts */ - CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */ - CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */ - CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ - CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - USART3_IRQn = 39, /*!< USART3 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */ - TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */ - TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */ - TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare Interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - FMC_IRQn = 48, /*!< FMC global Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - UART4_IRQn = 52, /*!< UART4 global Interrupt */ - UART5_IRQn = 53, /*!< UART5 global Interrupt */ - TIM6_DAC_IRQn = 54, /*!< TIM6 global and DAC1&2 underrun error interrupts */ - TIM7_IRQn = 55, /*!< TIM7 global interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - ETH_IRQn = 61, /*!< Ethernet global Interrupt */ - ETH_WKUP_IRQn = 62, /*!< Ethernet Wakeup through EXTI line Interrupt */ - CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */ - CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */ - CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */ - CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - OTG_HS_EP1_OUT_IRQn = 74, /*!< USB OTG HS End Point 1 Out global interrupt */ - OTG_HS_EP1_IN_IRQn = 75, /*!< USB OTG HS End Point 1 In global interrupt */ - OTG_HS_WKUP_IRQn = 76, /*!< USB OTG HS Wakeup through EXTI interrupt */ - OTG_HS_IRQn = 77, /*!< USB OTG HS global interrupt */ - DCMI_IRQn = 78, /*!< DCMI global interrupt */ - CRYP_IRQn = 79, /*!< CRYP crypto global interrupt */ - HASH_RNG_IRQn = 80, /*!< Hash and Rng global interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - UART7_IRQn = 82, /*!< UART7 global interrupt */ - UART8_IRQn = 83, /*!< UART8 global interrupt */ - SPI4_IRQn = 84, /*!< SPI4 global Interrupt */ - SPI5_IRQn = 85, /*!< SPI5 global Interrupt */ - SPI6_IRQn = 86, /*!< SPI6 global Interrupt */ - SAI1_IRQn = 87, /*!< SAI1 global Interrupt */ - DMA2D_IRQn = 90 /*!< DMA2D global Interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - - -/** - * @brief Controller Area Network TxMailBox - */ - -typedef struct -{ - __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ - __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ - __IO uint32_t TDLR; /*!< CAN mailbox data low register */ - __IO uint32_t TDHR; /*!< CAN mailbox data high register */ -} CAN_TxMailBox_TypeDef; - -/** - * @brief Controller Area Network FIFOMailBox - */ - -typedef struct -{ - __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ - __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ - __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ - __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ -} CAN_FIFOMailBox_TypeDef; - -/** - * @brief Controller Area Network FilterRegister - */ - -typedef struct -{ - __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ - __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ -} CAN_FilterRegister_TypeDef; - -/** - * @brief Controller Area Network - */ - -typedef struct -{ - __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ - __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ - __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ - __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ - __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ - __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ - __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ - __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ - uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ - CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ - CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ - uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ - __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ - __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ - uint32_t RESERVED2; /*!< Reserved, 0x208 */ - __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ - uint32_t RESERVED3; /*!< Reserved, 0x210 */ - __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ - uint32_t RESERVED4; /*!< Reserved, 0x218 */ - __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ - uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ - CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ -} CAN_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Digital to Analog Converter - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ - __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ - __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ - __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ - __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ - __IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */ - __IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */ - __IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */ - __IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */ - __IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */ - __IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */ - __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ - __IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */ - __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ -} DAC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - -/** - * @brief DCMI - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DCMI control register 1, Address offset: 0x00 */ - __IO uint32_t SR; /*!< DCMI status register, Address offset: 0x04 */ - __IO uint32_t RISR; /*!< DCMI raw interrupt status register, Address offset: 0x08 */ - __IO uint32_t IER; /*!< DCMI interrupt enable register, Address offset: 0x0C */ - __IO uint32_t MISR; /*!< DCMI masked interrupt status register, Address offset: 0x10 */ - __IO uint32_t ICR; /*!< DCMI interrupt clear register, Address offset: 0x14 */ - __IO uint32_t ESCR; /*!< DCMI embedded synchronization code register, Address offset: 0x18 */ - __IO uint32_t ESUR; /*!< DCMI embedded synchronization unmask register, Address offset: 0x1C */ - __IO uint32_t CWSTRTR; /*!< DCMI crop window start, Address offset: 0x20 */ - __IO uint32_t CWSIZER; /*!< DCMI crop window size, Address offset: 0x24 */ - __IO uint32_t DR; /*!< DCMI data register, Address offset: 0x28 */ -} DCMI_TypeDef; - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - -/** - * @brief DMA2D Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA2D Control Register, Address offset: 0x00 */ - __IO uint32_t ISR; /*!< DMA2D Interrupt Status Register, Address offset: 0x04 */ - __IO uint32_t IFCR; /*!< DMA2D Interrupt Flag Clear Register, Address offset: 0x08 */ - __IO uint32_t FGMAR; /*!< DMA2D Foreground Memory Address Register, Address offset: 0x0C */ - __IO uint32_t FGOR; /*!< DMA2D Foreground Offset Register, Address offset: 0x10 */ - __IO uint32_t BGMAR; /*!< DMA2D Background Memory Address Register, Address offset: 0x14 */ - __IO uint32_t BGOR; /*!< DMA2D Background Offset Register, Address offset: 0x18 */ - __IO uint32_t FGPFCCR; /*!< DMA2D Foreground PFC Control Register, Address offset: 0x1C */ - __IO uint32_t FGCOLR; /*!< DMA2D Foreground Color Register, Address offset: 0x20 */ - __IO uint32_t BGPFCCR; /*!< DMA2D Background PFC Control Register, Address offset: 0x24 */ - __IO uint32_t BGCOLR; /*!< DMA2D Background Color Register, Address offset: 0x28 */ - __IO uint32_t FGCMAR; /*!< DMA2D Foreground CLUT Memory Address Register, Address offset: 0x2C */ - __IO uint32_t BGCMAR; /*!< DMA2D Background CLUT Memory Address Register, Address offset: 0x30 */ - __IO uint32_t OPFCCR; /*!< DMA2D Output PFC Control Register, Address offset: 0x34 */ - __IO uint32_t OCOLR; /*!< DMA2D Output Color Register, Address offset: 0x38 */ - __IO uint32_t OMAR; /*!< DMA2D Output Memory Address Register, Address offset: 0x3C */ - __IO uint32_t OOR; /*!< DMA2D Output Offset Register, Address offset: 0x40 */ - __IO uint32_t NLR; /*!< DMA2D Number of Line Register, Address offset: 0x44 */ - __IO uint32_t LWR; /*!< DMA2D Line Watermark Register, Address offset: 0x48 */ - __IO uint32_t AMTCR; /*!< DMA2D AHB Master Timer Configuration Register, Address offset: 0x4C */ - uint32_t RESERVED[236]; /*!< Reserved, 0x50-0x3FF */ - __IO uint32_t FGCLUT[256]; /*!< DMA2D Foreground CLUT, Address offset:400-7FF */ - __IO uint32_t BGCLUT[256]; /*!< DMA2D Background CLUT, Address offset:800-BFF */ -} DMA2D_TypeDef; - -/** - * @brief Ethernet MAC - */ - -typedef struct -{ - __IO uint32_t MACCR; - __IO uint32_t MACFFR; - __IO uint32_t MACHTHR; - __IO uint32_t MACHTLR; - __IO uint32_t MACMIIAR; - __IO uint32_t MACMIIDR; - __IO uint32_t MACFCR; - __IO uint32_t MACVLANTR; /* 8 */ - uint32_t RESERVED0[2]; - __IO uint32_t MACRWUFFR; /* 11 */ - __IO uint32_t MACPMTCSR; - uint32_t RESERVED1[2]; - __IO uint32_t MACSR; /* 15 */ - __IO uint32_t MACIMR; - __IO uint32_t MACA0HR; - __IO uint32_t MACA0LR; - __IO uint32_t MACA1HR; - __IO uint32_t MACA1LR; - __IO uint32_t MACA2HR; - __IO uint32_t MACA2LR; - __IO uint32_t MACA3HR; - __IO uint32_t MACA3LR; /* 24 */ - uint32_t RESERVED2[40]; - __IO uint32_t MMCCR; /* 65 */ - __IO uint32_t MMCRIR; - __IO uint32_t MMCTIR; - __IO uint32_t MMCRIMR; - __IO uint32_t MMCTIMR; /* 69 */ - uint32_t RESERVED3[14]; - __IO uint32_t MMCTGFSCCR; /* 84 */ - __IO uint32_t MMCTGFMSCCR; - uint32_t RESERVED4[5]; - __IO uint32_t MMCTGFCR; - uint32_t RESERVED5[10]; - __IO uint32_t MMCRFCECR; - __IO uint32_t MMCRFAECR; - uint32_t RESERVED6[10]; - __IO uint32_t MMCRGUFCR; - uint32_t RESERVED7[334]; - __IO uint32_t PTPTSCR; - __IO uint32_t PTPSSIR; - __IO uint32_t PTPTSHR; - __IO uint32_t PTPTSLR; - __IO uint32_t PTPTSHUR; - __IO uint32_t PTPTSLUR; - __IO uint32_t PTPTSAR; - __IO uint32_t PTPTTHR; - __IO uint32_t PTPTTLR; - __IO uint32_t RESERVED8; - __IO uint32_t PTPTSSR; - uint32_t RESERVED9[565]; - __IO uint32_t DMABMR; - __IO uint32_t DMATPDR; - __IO uint32_t DMARPDR; - __IO uint32_t DMARDLAR; - __IO uint32_t DMATDLAR; - __IO uint32_t DMASR; - __IO uint32_t DMAOMR; - __IO uint32_t DMAIER; - __IO uint32_t DMAMFBOCR; - __IO uint32_t DMARSWTR; - uint32_t RESERVED10[8]; - __IO uint32_t DMACHTDR; - __IO uint32_t DMACHRDR; - __IO uint32_t DMACHTBAR; - __IO uint32_t DMACHRBAR; -} ETH_TypeDef; - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief Flexible Memory Controller - */ - -typedef struct -{ - __IO uint32_t BTCR[8]; /*!< NOR/PSRAM chip-select control register(BCR) and chip-select timing register(BTR), Address offset: 0x00-1C */ -} FMC_Bank1_TypeDef; - -/** - * @brief Flexible Memory Controller Bank1E - */ - -typedef struct -{ - __IO uint32_t BWTR[7]; /*!< NOR/PSRAM write timing registers, Address offset: 0x104-0x11C */ -} FMC_Bank1E_TypeDef; - -/** - * @brief Flexible Memory Controller Bank2 - */ - -typedef struct -{ - __IO uint32_t PCR2; /*!< NAND Flash control register 2, Address offset: 0x60 */ - __IO uint32_t SR2; /*!< NAND Flash FIFO status and interrupt register 2, Address offset: 0x64 */ - __IO uint32_t PMEM2; /*!< NAND Flash Common memory space timing register 2, Address offset: 0x68 */ - __IO uint32_t PATT2; /*!< NAND Flash Attribute memory space timing register 2, Address offset: 0x6C */ - uint32_t RESERVED0; /*!< Reserved, 0x70 */ - __IO uint32_t ECCR2; /*!< NAND Flash ECC result registers 2, Address offset: 0x74 */ - uint32_t RESERVED1; /*!< Reserved, 0x78 */ - uint32_t RESERVED2; /*!< Reserved, 0x7C */ - __IO uint32_t PCR3; /*!< NAND Flash control register 3, Address offset: 0x80 */ - __IO uint32_t SR3; /*!< NAND Flash FIFO status and interrupt register 3, Address offset: 0x84 */ - __IO uint32_t PMEM3; /*!< NAND Flash Common memory space timing register 3, Address offset: 0x88 */ - __IO uint32_t PATT3; /*!< NAND Flash Attribute memory space timing register 3, Address offset: 0x8C */ - uint32_t RESERVED3; /*!< Reserved, 0x90 */ - __IO uint32_t ECCR3; /*!< NAND Flash ECC result registers 3, Address offset: 0x94 */ -} FMC_Bank2_3_TypeDef; - -/** - * @brief Flexible Memory Controller Bank4 - */ - -typedef struct -{ - __IO uint32_t PCR4; /*!< PC Card control register 4, Address offset: 0xA0 */ - __IO uint32_t SR4; /*!< PC Card FIFO status and interrupt register 4, Address offset: 0xA4 */ - __IO uint32_t PMEM4; /*!< PC Card Common memory space timing register 4, Address offset: 0xA8 */ - __IO uint32_t PATT4; /*!< PC Card Attribute memory space timing register 4, Address offset: 0xAC */ - __IO uint32_t PIO4; /*!< PC Card I/O space timing register 4, Address offset: 0xB0 */ -} FMC_Bank4_TypeDef; - -/** - * @brief Flexible Memory Controller Bank5_6 - */ - -typedef struct -{ - __IO uint32_t SDCR[2]; /*!< SDRAM Control registers , Address offset: 0x140-0x144 */ - __IO uint32_t SDTR[2]; /*!< SDRAM Timing registers , Address offset: 0x148-0x14C */ - __IO uint32_t SDCMR; /*!< SDRAM Command Mode register, Address offset: 0x150 */ - __IO uint32_t SDRTR; /*!< SDRAM Refresh Timer register, Address offset: 0x154 */ - __IO uint32_t SDSR; /*!< SDRAM Status register, Address offset: 0x158 */ -} FMC_Bank5_6_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - __IO uint32_t PLLSAICFGR; /*!< RCC PLLSAI configuration register, Address offset: 0x88 */ - __IO uint32_t DCKCFGR; /*!< RCC Dedicated Clocks configuration register, Address offset: 0x8C */ - -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - -/** - * @brief Serial Audio Interface - */ - -typedef struct -{ - __IO uint32_t GCR; /*!< SAI global configuration register, Address offset: 0x00 */ -} SAI_TypeDef; - -typedef struct -{ - __IO uint32_t CR1; /*!< SAI block x configuration register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< SAI block x configuration register 2, Address offset: 0x08 */ - __IO uint32_t FRCR; /*!< SAI block x frame configuration register, Address offset: 0x0C */ - __IO uint32_t SLOTR; /*!< SAI block x slot register, Address offset: 0x10 */ - __IO uint32_t IMR; /*!< SAI block x interrupt mask register, Address offset: 0x14 */ - __IO uint32_t SR; /*!< SAI block x status register, Address offset: 0x18 */ - __IO uint32_t CLRFR; /*!< SAI block x clear flag register, Address offset: 0x1C */ - __IO uint32_t DR; /*!< SAI block x data register, Address offset: 0x20 */ -} SAI_Block_TypeDef; - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - -/** - * @brief Crypto Processor - */ - -typedef struct -{ - __IO uint32_t CR; /*!< CRYP control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< CRYP status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< CRYP data input register, Address offset: 0x08 */ - __IO uint32_t DOUT; /*!< CRYP data output register, Address offset: 0x0C */ - __IO uint32_t DMACR; /*!< CRYP DMA control register, Address offset: 0x10 */ - __IO uint32_t IMSCR; /*!< CRYP interrupt mask set/clear register, Address offset: 0x14 */ - __IO uint32_t RISR; /*!< CRYP raw interrupt status register, Address offset: 0x18 */ - __IO uint32_t MISR; /*!< CRYP masked interrupt status register, Address offset: 0x1C */ - __IO uint32_t K0LR; /*!< CRYP key left register 0, Address offset: 0x20 */ - __IO uint32_t K0RR; /*!< CRYP key right register 0, Address offset: 0x24 */ - __IO uint32_t K1LR; /*!< CRYP key left register 1, Address offset: 0x28 */ - __IO uint32_t K1RR; /*!< CRYP key right register 1, Address offset: 0x2C */ - __IO uint32_t K2LR; /*!< CRYP key left register 2, Address offset: 0x30 */ - __IO uint32_t K2RR; /*!< CRYP key right register 2, Address offset: 0x34 */ - __IO uint32_t K3LR; /*!< CRYP key left register 3, Address offset: 0x38 */ - __IO uint32_t K3RR; /*!< CRYP key right register 3, Address offset: 0x3C */ - __IO uint32_t IV0LR; /*!< CRYP initialization vector left-word register 0, Address offset: 0x40 */ - __IO uint32_t IV0RR; /*!< CRYP initialization vector right-word register 0, Address offset: 0x44 */ - __IO uint32_t IV1LR; /*!< CRYP initialization vector left-word register 1, Address offset: 0x48 */ - __IO uint32_t IV1RR; /*!< CRYP initialization vector right-word register 1, Address offset: 0x4C */ - __IO uint32_t CSGCMCCM0R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 0, Address offset: 0x50 */ - __IO uint32_t CSGCMCCM1R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 1, Address offset: 0x54 */ - __IO uint32_t CSGCMCCM2R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 2, Address offset: 0x58 */ - __IO uint32_t CSGCMCCM3R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 3, Address offset: 0x5C */ - __IO uint32_t CSGCMCCM4R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 4, Address offset: 0x60 */ - __IO uint32_t CSGCMCCM5R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 5, Address offset: 0x64 */ - __IO uint32_t CSGCMCCM6R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 6, Address offset: 0x68 */ - __IO uint32_t CSGCMCCM7R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 7, Address offset: 0x6C */ - __IO uint32_t CSGCM0R; /*!< CRYP GCM/GMAC context swap register 0, Address offset: 0x70 */ - __IO uint32_t CSGCM1R; /*!< CRYP GCM/GMAC context swap register 1, Address offset: 0x74 */ - __IO uint32_t CSGCM2R; /*!< CRYP GCM/GMAC context swap register 2, Address offset: 0x78 */ - __IO uint32_t CSGCM3R; /*!< CRYP GCM/GMAC context swap register 3, Address offset: 0x7C */ - __IO uint32_t CSGCM4R; /*!< CRYP GCM/GMAC context swap register 4, Address offset: 0x80 */ - __IO uint32_t CSGCM5R; /*!< CRYP GCM/GMAC context swap register 5, Address offset: 0x84 */ - __IO uint32_t CSGCM6R; /*!< CRYP GCM/GMAC context swap register 6, Address offset: 0x88 */ - __IO uint32_t CSGCM7R; /*!< CRYP GCM/GMAC context swap register 7, Address offset: 0x8C */ -} CRYP_TypeDef; - -/** - * @brief HASH - */ - -typedef struct -{ - __IO uint32_t CR; /*!< HASH control register, Address offset: 0x00 */ - __IO uint32_t DIN; /*!< HASH data input register, Address offset: 0x04 */ - __IO uint32_t STR; /*!< HASH start register, Address offset: 0x08 */ - __IO uint32_t HR[5]; /*!< HASH digest registers, Address offset: 0x0C-0x1C */ - __IO uint32_t IMR; /*!< HASH interrupt enable register, Address offset: 0x20 */ - __IO uint32_t SR; /*!< HASH status register, Address offset: 0x24 */ - uint32_t RESERVED[52]; /*!< Reserved, 0x28-0xF4 */ - __IO uint32_t CSR[54]; /*!< HASH context swap registers, Address offset: 0x0F8-0x1CC */ -} HASH_TypeDef; - -/** - * @brief HASH_DIGEST - */ - -typedef struct -{ - __IO uint32_t HR[8]; /*!< HASH digest registers, Address offset: 0x310-0x32C */ -} HASH_DIGEST_TypeDef; - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - -/** - * @brief __USB_OTG_Core_register - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register 000h */ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register 004h */ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register 008h */ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register 00Ch */ - __IO uint32_t GRSTCTL; /*!< Core Reset Register 010h */ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register 014h */ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register 018h */ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register 01Ch */ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register 020h */ - __IO uint32_t GRXFSIZ; /* Receive FIFO Size Register 024h */ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register 028h*/ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg 02Ch */ - uint32_t Reserved30[2]; /* Reserved 030h*/ - __IO uint32_t GCCFG; /* General Purpose IO Register 038h*/ - __IO uint32_t CID; /* User ID Register 03Ch*/ - uint32_t Reserved40[48]; /* Reserved 040h-0FFh*/ - __IO uint32_t HPTXFSIZ; /* Host Periodic Tx FIFO Size Reg 100h*/ - __IO uint32_t DIEPTXF[0x0F];/* dev Periodic Transmit FIFO */ -} -USB_OTG_GlobalTypeDef; - - -/** - * @brief __device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /* dev Configuration Register 800h*/ - __IO uint32_t DCTL; /* dev Control Register 804h*/ - __IO uint32_t DSTS; /* dev Status Register (RO) 808h*/ - uint32_t Reserved0C; /* Reserved 80Ch*/ - __IO uint32_t DIEPMSK; /* dev IN Endpoint Mask 810h*/ - __IO uint32_t DOEPMSK; /* dev OUT Endpoint Mask 814h*/ - __IO uint32_t DAINT; /* dev All Endpoints Itr Reg 818h*/ - __IO uint32_t DAINTMSK; /* dev All Endpoints Itr Mask 81Ch*/ - uint32_t Reserved20; /* Reserved 820h*/ - uint32_t Reserved9; /* Reserved 824h*/ - __IO uint32_t DVBUSDIS; /* dev VBUS discharge Register 828h*/ - __IO uint32_t DVBUSPULSE; /* dev VBUS Pulse Register 82Ch*/ - __IO uint32_t DTHRCTL; /* dev thr 830h*/ - __IO uint32_t DIEPEMPMSK; /* dev empty msk 834h*/ - __IO uint32_t DEACHINT; /* dedicated EP interrupt 838h*/ - __IO uint32_t DEACHMSK; /* dedicated EP msk 83Ch*/ - uint32_t Reserved40; /* dedicated EP mask 840h*/ - __IO uint32_t DINEP1MSK; /* dedicated EP mask 844h*/ - uint32_t Reserved44[15]; /* Reserved 844-87Ch*/ - __IO uint32_t DOUTEP1MSK; /* dedicated EP msk 884h*/ -} -USB_OTG_DeviceTypeDef; - - -/** - * @brief __IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /* dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved 900h + (ep_num * 20h) + 04h*/ - __IO uint32_t DIEPINT; /* dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved 900h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DIEPTSIZ; /* IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h*/ - __IO uint32_t DIEPDMA; /* IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h*/ - __IO uint32_t DTXFSTS;/*IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h*/ - uint32_t Reserved18; /* Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch*/ -} -USB_OTG_INEndpointTypeDef; - - -/** - * @brief __OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /* dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved B00h + (ep_num * 20h) + 04h*/ - __IO uint32_t DOEPINT; /* dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved B00h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DOEPTSIZ; /* dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h*/ - __IO uint32_t DOEPDMA; /* dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h*/ - uint32_t Reserved18[2]; /* Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch*/ -} -USB_OTG_OUTEndpointTypeDef; - - -/** - * @brief __Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /* Host Configuration Register 400h*/ - __IO uint32_t HFIR; /* Host Frame Interval Register 404h*/ - __IO uint32_t HFNUM; /* Host Frame Nbr/Frame Remaining 408h*/ - uint32_t Reserved40C; /* Reserved 40Ch*/ - __IO uint32_t HPTXSTS; /* Host Periodic Tx FIFO/ Queue Status 410h*/ - __IO uint32_t HAINT; /* Host All Channels Interrupt Register 414h*/ - __IO uint32_t HAINTMSK; /* Host All Channels Interrupt Mask 418h*/ -} -USB_OTG_HostTypeDef; - -/** - * @brief __Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; - __IO uint32_t HCSPLT; - __IO uint32_t HCINT; - __IO uint32_t HCINTMSK; - __IO uint32_t HCTSIZ; - __IO uint32_t HCDMA; - uint32_t Reserved[2]; -} -USB_OTG_HostChannelTypeDef; -/** - * @} - */ - -/** @addtogroup Peripheral_memory_map - * @{ - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 2 MB) base address in the alias region */ -#define CCMDATARAM_BASE 0x10000000U /*!< CCM(core coupled memory) data RAM(64 KB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(112 KB) base address in the alias region */ -#define SRAM2_BASE 0x2001C000U /*!< SRAM2(16 KB) base address in the alias region */ -#define SRAM3_BASE 0x20020000U /*!< SRAM3(64 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define BKPSRAM_BASE 0x40024000U /*!< Backup SRAM(4 KB) base address in the alias region */ -#define FMC_R_BASE 0xA0000000U /*!< FMC registers base address */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(112 KB) base address in the bit-band region */ -#define SRAM2_BB_BASE 0x22380000U /*!< SRAM2(16 KB) base address in the bit-band region */ -#define SRAM3_BB_BASE 0x22400000U /*!< SRAM3(64 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define BKPSRAM_BB_BASE 0x42480000U /*!< Backup SRAM(4 KB) base address in the bit-band region */ -#define FLASH_END 0x081FFFFFU /*!< FLASH end address */ -#define CCMDATARAM_END 0x1000FFFFU /*!< CCM data RAM end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define TIM7_BASE (APB1PERIPH_BASE + 0x1400U) -#define TIM12_BASE (APB1PERIPH_BASE + 0x1800U) -#define TIM13_BASE (APB1PERIPH_BASE + 0x1C00U) -#define TIM14_BASE (APB1PERIPH_BASE + 0x2000U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define USART3_BASE (APB1PERIPH_BASE + 0x4800U) -#define UART4_BASE (APB1PERIPH_BASE + 0x4C00U) -#define UART5_BASE (APB1PERIPH_BASE + 0x5000U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define CAN1_BASE (APB1PERIPH_BASE + 0x6400U) -#define CAN2_BASE (APB1PERIPH_BASE + 0x6800U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) -#define DAC_BASE (APB1PERIPH_BASE + 0x7400U) -#define UART7_BASE (APB1PERIPH_BASE + 0x7800U) -#define UART8_BASE (APB1PERIPH_BASE + 0x7C00U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define TIM8_BASE (APB2PERIPH_BASE + 0x0400U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC2_BASE (APB2PERIPH_BASE + 0x2100U) -#define ADC3_BASE (APB2PERIPH_BASE + 0x2200U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SPI4_BASE (APB2PERIPH_BASE + 0x3400U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) -#define SPI5_BASE (APB2PERIPH_BASE + 0x5000U) -#define SPI6_BASE (APB2PERIPH_BASE + 0x5400U) -#define SAI1_BASE (APB2PERIPH_BASE + 0x5800U) -#define SAI1_Block_A_BASE (SAI1_BASE + 0x004U) -#define SAI1_Block_B_BASE (SAI1_BASE + 0x024U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOF_BASE (AHB1PERIPH_BASE + 0x1400U) -#define GPIOG_BASE (AHB1PERIPH_BASE + 0x1800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define GPIOI_BASE (AHB1PERIPH_BASE + 0x2000U) -#define GPIOJ_BASE (AHB1PERIPH_BASE + 0x2400U) -#define GPIOK_BASE (AHB1PERIPH_BASE + 0x2800U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) -#define ETH_BASE (AHB1PERIPH_BASE + 0x8000U) -#define ETH_MAC_BASE (ETH_BASE) -#define ETH_MMC_BASE (ETH_BASE + 0x0100U) -#define ETH_PTP_BASE (ETH_BASE + 0x0700U) -#define ETH_DMA_BASE (ETH_BASE + 0x1000U) -#define DMA2D_BASE (AHB1PERIPH_BASE + 0xB000U) - -/*!< AHB2 peripherals */ -#define DCMI_BASE (AHB2PERIPH_BASE + 0x50000U) -#define CRYP_BASE (AHB2PERIPH_BASE + 0x60000U) -#define HASH_BASE (AHB2PERIPH_BASE + 0x60400U) -#define HASH_DIGEST_BASE (AHB2PERIPH_BASE + 0x60710U) -#define RNG_BASE (AHB2PERIPH_BASE + 0x60800U) - -/*!< FMC Bankx registers base address */ -#define FMC_Bank1_R_BASE (FMC_R_BASE + 0x0000U) -#define FMC_Bank1E_R_BASE (FMC_R_BASE + 0x0104U) -#define FMC_Bank2_3_R_BASE (FMC_R_BASE + 0x0060U) -#define FMC_Bank4_R_BASE (FMC_R_BASE + 0x00A0U) -#define FMC_Bank5_6_R_BASE (FMC_R_BASE + 0x0140U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_HS_PERIPH_BASE 0x40040000U -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define TIM7 ((TIM_TypeDef *) TIM7_BASE) -#define TIM12 ((TIM_TypeDef *) TIM12_BASE) -#define TIM13 ((TIM_TypeDef *) TIM13_BASE) -#define TIM14 ((TIM_TypeDef *) TIM14_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define USART3 ((USART_TypeDef *) USART3_BASE) -#define UART4 ((USART_TypeDef *) UART4_BASE) -#define UART5 ((USART_TypeDef *) UART5_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define CAN1 ((CAN_TypeDef *) CAN1_BASE) -#define CAN2 ((CAN_TypeDef *) CAN2_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define DAC ((DAC_TypeDef *) DAC_BASE) -#define UART7 ((USART_TypeDef *) UART7_BASE) -#define UART8 ((USART_TypeDef *) UART8_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define TIM8 ((TIM_TypeDef *) TIM8_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define ADC2 ((ADC_TypeDef *) ADC2_BASE) -#define ADC3 ((ADC_TypeDef *) ADC3_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SPI4 ((SPI_TypeDef *) SPI4_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define SPI5 ((SPI_TypeDef *) SPI5_BASE) -#define SPI6 ((SPI_TypeDef *) SPI6_BASE) -#define SAI1 ((SAI_TypeDef *) SAI1_BASE) -#define SAI1_Block_A ((SAI_Block_TypeDef *)SAI1_Block_A_BASE) -#define SAI1_Block_B ((SAI_Block_TypeDef *)SAI1_Block_B_BASE) - -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOF ((GPIO_TypeDef *) GPIOF_BASE) -#define GPIOG ((GPIO_TypeDef *) GPIOG_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define GPIOI ((GPIO_TypeDef *) GPIOI_BASE) -#define GPIOJ ((GPIO_TypeDef *) GPIOJ_BASE) -#define GPIOK ((GPIO_TypeDef *) GPIOK_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define ETH ((ETH_TypeDef *) ETH_BASE) -#define DMA2D ((DMA2D_TypeDef *)DMA2D_BASE) -#define DCMI ((DCMI_TypeDef *) DCMI_BASE) -#define CRYP ((CRYP_TypeDef *) CRYP_BASE) -#define HASH ((HASH_TypeDef *) HASH_BASE) -#define HASH_DIGEST ((HASH_DIGEST_TypeDef *) HASH_DIGEST_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) -#define FMC_Bank1 ((FMC_Bank1_TypeDef *) FMC_Bank1_R_BASE) -#define FMC_Bank1E ((FMC_Bank1E_TypeDef *) FMC_Bank1E_R_BASE) -#define FMC_Bank2_3 ((FMC_Bank2_3_TypeDef *) FMC_Bank2_3_R_BASE) -#define FMC_Bank4 ((FMC_Bank4_TypeDef *) FMC_Bank4_R_BASE) -#define FMC_Bank5_6 ((FMC_Bank5_6_TypeDef *) FMC_Bank5_6_R_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) -#define USB_OTG_HS ((USB_OTG_GlobalTypeDef *) USB_OTG_HS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS_Device - * @{ - */ - -/** @addtogroup stm32f439xx - * @{ - */ - -#ifndef __STM32F439xx_H -#define __STM32F439xx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1, ADC2 and ADC3 global Interrupts */ - CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */ - CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */ - CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ - CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - USART3_IRQn = 39, /*!< USART3 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */ - TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */ - TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */ - TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare Interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - FMC_IRQn = 48, /*!< FMC global Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - UART4_IRQn = 52, /*!< UART4 global Interrupt */ - UART5_IRQn = 53, /*!< UART5 global Interrupt */ - TIM6_DAC_IRQn = 54, /*!< TIM6 global and DAC1&2 underrun error interrupts */ - TIM7_IRQn = 55, /*!< TIM7 global interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - ETH_IRQn = 61, /*!< Ethernet global Interrupt */ - ETH_WKUP_IRQn = 62, /*!< Ethernet Wakeup through EXTI line Interrupt */ - CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */ - CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */ - CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */ - CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - OTG_HS_EP1_OUT_IRQn = 74, /*!< USB OTG HS End Point 1 Out global interrupt */ - OTG_HS_EP1_IN_IRQn = 75, /*!< USB OTG HS End Point 1 In global interrupt */ - OTG_HS_WKUP_IRQn = 76, /*!< USB OTG HS Wakeup through EXTI interrupt */ - OTG_HS_IRQn = 77, /*!< USB OTG HS global interrupt */ - DCMI_IRQn = 78, /*!< DCMI global interrupt */ - CRYP_IRQn = 79, /*!< CRYP crypto global interrupt */ - HASH_RNG_IRQn = 80, /*!< Hash and Rng global interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - UART7_IRQn = 82, /*!< UART7 global interrupt */ - UART8_IRQn = 83, /*!< UART8 global interrupt */ - SPI4_IRQn = 84, /*!< SPI4 global Interrupt */ - SPI5_IRQn = 85, /*!< SPI5 global Interrupt */ - SPI6_IRQn = 86, /*!< SPI6 global Interrupt */ - SAI1_IRQn = 87, /*!< SAI1 global Interrupt */ - LTDC_IRQn = 88, /*!< LTDC global Interrupt */ - LTDC_ER_IRQn = 89, /*!< LTDC Error global Interrupt */ - DMA2D_IRQn = 90 /*!< DMA2D global Interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - - -/** - * @brief Controller Area Network TxMailBox - */ - -typedef struct -{ - __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ - __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ - __IO uint32_t TDLR; /*!< CAN mailbox data low register */ - __IO uint32_t TDHR; /*!< CAN mailbox data high register */ -} CAN_TxMailBox_TypeDef; - -/** - * @brief Controller Area Network FIFOMailBox - */ - -typedef struct -{ - __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ - __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ - __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ - __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ -} CAN_FIFOMailBox_TypeDef; - -/** - * @brief Controller Area Network FilterRegister - */ - -typedef struct -{ - __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ - __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ -} CAN_FilterRegister_TypeDef; - -/** - * @brief Controller Area Network - */ - -typedef struct -{ - __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ - __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ - __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ - __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ - __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ - __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ - __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ - __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ - uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ - CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ - CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ - uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ - __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ - __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ - uint32_t RESERVED2; /*!< Reserved, 0x208 */ - __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ - uint32_t RESERVED3; /*!< Reserved, 0x210 */ - __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ - uint32_t RESERVED4; /*!< Reserved, 0x218 */ - __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ - uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ - CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ -} CAN_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Digital to Analog Converter - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ - __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ - __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ - __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ - __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ - __IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */ - __IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */ - __IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */ - __IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */ - __IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */ - __IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */ - __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ - __IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */ - __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ -} DAC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - -/** - * @brief DCMI - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DCMI control register 1, Address offset: 0x00 */ - __IO uint32_t SR; /*!< DCMI status register, Address offset: 0x04 */ - __IO uint32_t RISR; /*!< DCMI raw interrupt status register, Address offset: 0x08 */ - __IO uint32_t IER; /*!< DCMI interrupt enable register, Address offset: 0x0C */ - __IO uint32_t MISR; /*!< DCMI masked interrupt status register, Address offset: 0x10 */ - __IO uint32_t ICR; /*!< DCMI interrupt clear register, Address offset: 0x14 */ - __IO uint32_t ESCR; /*!< DCMI embedded synchronization code register, Address offset: 0x18 */ - __IO uint32_t ESUR; /*!< DCMI embedded synchronization unmask register, Address offset: 0x1C */ - __IO uint32_t CWSTRTR; /*!< DCMI crop window start, Address offset: 0x20 */ - __IO uint32_t CWSIZER; /*!< DCMI crop window size, Address offset: 0x24 */ - __IO uint32_t DR; /*!< DCMI data register, Address offset: 0x28 */ -} DCMI_TypeDef; - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - -/** - * @brief DMA2D Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA2D Control Register, Address offset: 0x00 */ - __IO uint32_t ISR; /*!< DMA2D Interrupt Status Register, Address offset: 0x04 */ - __IO uint32_t IFCR; /*!< DMA2D Interrupt Flag Clear Register, Address offset: 0x08 */ - __IO uint32_t FGMAR; /*!< DMA2D Foreground Memory Address Register, Address offset: 0x0C */ - __IO uint32_t FGOR; /*!< DMA2D Foreground Offset Register, Address offset: 0x10 */ - __IO uint32_t BGMAR; /*!< DMA2D Background Memory Address Register, Address offset: 0x14 */ - __IO uint32_t BGOR; /*!< DMA2D Background Offset Register, Address offset: 0x18 */ - __IO uint32_t FGPFCCR; /*!< DMA2D Foreground PFC Control Register, Address offset: 0x1C */ - __IO uint32_t FGCOLR; /*!< DMA2D Foreground Color Register, Address offset: 0x20 */ - __IO uint32_t BGPFCCR; /*!< DMA2D Background PFC Control Register, Address offset: 0x24 */ - __IO uint32_t BGCOLR; /*!< DMA2D Background Color Register, Address offset: 0x28 */ - __IO uint32_t FGCMAR; /*!< DMA2D Foreground CLUT Memory Address Register, Address offset: 0x2C */ - __IO uint32_t BGCMAR; /*!< DMA2D Background CLUT Memory Address Register, Address offset: 0x30 */ - __IO uint32_t OPFCCR; /*!< DMA2D Output PFC Control Register, Address offset: 0x34 */ - __IO uint32_t OCOLR; /*!< DMA2D Output Color Register, Address offset: 0x38 */ - __IO uint32_t OMAR; /*!< DMA2D Output Memory Address Register, Address offset: 0x3C */ - __IO uint32_t OOR; /*!< DMA2D Output Offset Register, Address offset: 0x40 */ - __IO uint32_t NLR; /*!< DMA2D Number of Line Register, Address offset: 0x44 */ - __IO uint32_t LWR; /*!< DMA2D Line Watermark Register, Address offset: 0x48 */ - __IO uint32_t AMTCR; /*!< DMA2D AHB Master Timer Configuration Register, Address offset: 0x4C */ - uint32_t RESERVED[236]; /*!< Reserved, 0x50-0x3FF */ - __IO uint32_t FGCLUT[256]; /*!< DMA2D Foreground CLUT, Address offset:400-7FF */ - __IO uint32_t BGCLUT[256]; /*!< DMA2D Background CLUT, Address offset:800-BFF */ -} DMA2D_TypeDef; - -/** - * @brief Ethernet MAC - */ - -typedef struct -{ - __IO uint32_t MACCR; - __IO uint32_t MACFFR; - __IO uint32_t MACHTHR; - __IO uint32_t MACHTLR; - __IO uint32_t MACMIIAR; - __IO uint32_t MACMIIDR; - __IO uint32_t MACFCR; - __IO uint32_t MACVLANTR; /* 8 */ - uint32_t RESERVED0[2]; - __IO uint32_t MACRWUFFR; /* 11 */ - __IO uint32_t MACPMTCSR; - uint32_t RESERVED1[2]; - __IO uint32_t MACSR; /* 15 */ - __IO uint32_t MACIMR; - __IO uint32_t MACA0HR; - __IO uint32_t MACA0LR; - __IO uint32_t MACA1HR; - __IO uint32_t MACA1LR; - __IO uint32_t MACA2HR; - __IO uint32_t MACA2LR; - __IO uint32_t MACA3HR; - __IO uint32_t MACA3LR; /* 24 */ - uint32_t RESERVED2[40]; - __IO uint32_t MMCCR; /* 65 */ - __IO uint32_t MMCRIR; - __IO uint32_t MMCTIR; - __IO uint32_t MMCRIMR; - __IO uint32_t MMCTIMR; /* 69 */ - uint32_t RESERVED3[14]; - __IO uint32_t MMCTGFSCCR; /* 84 */ - __IO uint32_t MMCTGFMSCCR; - uint32_t RESERVED4[5]; - __IO uint32_t MMCTGFCR; - uint32_t RESERVED5[10]; - __IO uint32_t MMCRFCECR; - __IO uint32_t MMCRFAECR; - uint32_t RESERVED6[10]; - __IO uint32_t MMCRGUFCR; - uint32_t RESERVED7[334]; - __IO uint32_t PTPTSCR; - __IO uint32_t PTPSSIR; - __IO uint32_t PTPTSHR; - __IO uint32_t PTPTSLR; - __IO uint32_t PTPTSHUR; - __IO uint32_t PTPTSLUR; - __IO uint32_t PTPTSAR; - __IO uint32_t PTPTTHR; - __IO uint32_t PTPTTLR; - __IO uint32_t RESERVED8; - __IO uint32_t PTPTSSR; - uint32_t RESERVED9[565]; - __IO uint32_t DMABMR; - __IO uint32_t DMATPDR; - __IO uint32_t DMARPDR; - __IO uint32_t DMARDLAR; - __IO uint32_t DMATDLAR; - __IO uint32_t DMASR; - __IO uint32_t DMAOMR; - __IO uint32_t DMAIER; - __IO uint32_t DMAMFBOCR; - __IO uint32_t DMARSWTR; - uint32_t RESERVED10[8]; - __IO uint32_t DMACHTDR; - __IO uint32_t DMACHRDR; - __IO uint32_t DMACHTBAR; - __IO uint32_t DMACHRBAR; -} ETH_TypeDef; - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief Flexible Memory Controller - */ - -typedef struct -{ - __IO uint32_t BTCR[8]; /*!< NOR/PSRAM chip-select control register(BCR) and chip-select timing register(BTR), Address offset: 0x00-1C */ -} FMC_Bank1_TypeDef; - -/** - * @brief Flexible Memory Controller Bank1E - */ - -typedef struct -{ - __IO uint32_t BWTR[7]; /*!< NOR/PSRAM write timing registers, Address offset: 0x104-0x11C */ -} FMC_Bank1E_TypeDef; - -/** - * @brief Flexible Memory Controller Bank2 - */ - -typedef struct -{ - __IO uint32_t PCR2; /*!< NAND Flash control register 2, Address offset: 0x60 */ - __IO uint32_t SR2; /*!< NAND Flash FIFO status and interrupt register 2, Address offset: 0x64 */ - __IO uint32_t PMEM2; /*!< NAND Flash Common memory space timing register 2, Address offset: 0x68 */ - __IO uint32_t PATT2; /*!< NAND Flash Attribute memory space timing register 2, Address offset: 0x6C */ - uint32_t RESERVED0; /*!< Reserved, 0x70 */ - __IO uint32_t ECCR2; /*!< NAND Flash ECC result registers 2, Address offset: 0x74 */ - uint32_t RESERVED1; /*!< Reserved, 0x78 */ - uint32_t RESERVED2; /*!< Reserved, 0x7C */ - __IO uint32_t PCR3; /*!< NAND Flash control register 3, Address offset: 0x80 */ - __IO uint32_t SR3; /*!< NAND Flash FIFO status and interrupt register 3, Address offset: 0x84 */ - __IO uint32_t PMEM3; /*!< NAND Flash Common memory space timing register 3, Address offset: 0x88 */ - __IO uint32_t PATT3; /*!< NAND Flash Attribute memory space timing register 3, Address offset: 0x8C */ - uint32_t RESERVED3; /*!< Reserved, 0x90 */ - __IO uint32_t ECCR3; /*!< NAND Flash ECC result registers 3, Address offset: 0x94 */ -} FMC_Bank2_3_TypeDef; - -/** - * @brief Flexible Memory Controller Bank4 - */ - -typedef struct -{ - __IO uint32_t PCR4; /*!< PC Card control register 4, Address offset: 0xA0 */ - __IO uint32_t SR4; /*!< PC Card FIFO status and interrupt register 4, Address offset: 0xA4 */ - __IO uint32_t PMEM4; /*!< PC Card Common memory space timing register 4, Address offset: 0xA8 */ - __IO uint32_t PATT4; /*!< PC Card Attribute memory space timing register 4, Address offset: 0xAC */ - __IO uint32_t PIO4; /*!< PC Card I/O space timing register 4, Address offset: 0xB0 */ -} FMC_Bank4_TypeDef; - -/** - * @brief Flexible Memory Controller Bank5_6 - */ - -typedef struct -{ - __IO uint32_t SDCR[2]; /*!< SDRAM Control registers , Address offset: 0x140-0x144 */ - __IO uint32_t SDTR[2]; /*!< SDRAM Timing registers , Address offset: 0x148-0x14C */ - __IO uint32_t SDCMR; /*!< SDRAM Command Mode register, Address offset: 0x150 */ - __IO uint32_t SDRTR; /*!< SDRAM Refresh Timer register, Address offset: 0x154 */ - __IO uint32_t SDSR; /*!< SDRAM Status register, Address offset: 0x158 */ -} FMC_Bank5_6_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief LCD-TFT Display Controller - */ - -typedef struct -{ - uint32_t RESERVED0[2]; /*!< Reserved, 0x00-0x04 */ - __IO uint32_t SSCR; /*!< LTDC Synchronization Size Configuration Register, Address offset: 0x08 */ - __IO uint32_t BPCR; /*!< LTDC Back Porch Configuration Register, Address offset: 0x0C */ - __IO uint32_t AWCR; /*!< LTDC Active Width Configuration Register, Address offset: 0x10 */ - __IO uint32_t TWCR; /*!< LTDC Total Width Configuration Register, Address offset: 0x14 */ - __IO uint32_t GCR; /*!< LTDC Global Control Register, Address offset: 0x18 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x1C-0x20 */ - __IO uint32_t SRCR; /*!< LTDC Shadow Reload Configuration Register, Address offset: 0x24 */ - uint32_t RESERVED2[1]; /*!< Reserved, 0x28 */ - __IO uint32_t BCCR; /*!< LTDC Background Color Configuration Register, Address offset: 0x2C */ - uint32_t RESERVED3[1]; /*!< Reserved, 0x30 */ - __IO uint32_t IER; /*!< LTDC Interrupt Enable Register, Address offset: 0x34 */ - __IO uint32_t ISR; /*!< LTDC Interrupt Status Register, Address offset: 0x38 */ - __IO uint32_t ICR; /*!< LTDC Interrupt Clear Register, Address offset: 0x3C */ - __IO uint32_t LIPCR; /*!< LTDC Line Interrupt Position Configuration Register, Address offset: 0x40 */ - __IO uint32_t CPSR; /*!< LTDC Current Position Status Register, Address offset: 0x44 */ - __IO uint32_t CDSR; /*!< LTDC Current Display Status Register, Address offset: 0x48 */ -} LTDC_TypeDef; - -/** - * @brief LCD-TFT Display layer x Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< LTDC Layerx Control Register Address offset: 0x84 */ - __IO uint32_t WHPCR; /*!< LTDC Layerx Window Horizontal Position Configuration Register Address offset: 0x88 */ - __IO uint32_t WVPCR; /*!< LTDC Layerx Window Vertical Position Configuration Register Address offset: 0x8C */ - __IO uint32_t CKCR; /*!< LTDC Layerx Color Keying Configuration Register Address offset: 0x90 */ - __IO uint32_t PFCR; /*!< LTDC Layerx Pixel Format Configuration Register Address offset: 0x94 */ - __IO uint32_t CACR; /*!< LTDC Layerx Constant Alpha Configuration Register Address offset: 0x98 */ - __IO uint32_t DCCR; /*!< LTDC Layerx Default Color Configuration Register Address offset: 0x9C */ - __IO uint32_t BFCR; /*!< LTDC Layerx Blending Factors Configuration Register Address offset: 0xA0 */ - uint32_t RESERVED0[2]; /*!< Reserved */ - __IO uint32_t CFBAR; /*!< LTDC Layerx Color Frame Buffer Address Register Address offset: 0xAC */ - __IO uint32_t CFBLR; /*!< LTDC Layerx Color Frame Buffer Length Register Address offset: 0xB0 */ - __IO uint32_t CFBLNR; /*!< LTDC Layerx ColorFrame Buffer Line Number Register Address offset: 0xB4 */ - uint32_t RESERVED1[3]; /*!< Reserved */ - __IO uint32_t CLUTWR; /*!< LTDC Layerx CLUT Write Register Address offset: 0x144 */ - -} LTDC_Layer_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - __IO uint32_t PLLSAICFGR; /*!< RCC PLLSAI configuration register, Address offset: 0x88 */ - __IO uint32_t DCKCFGR; /*!< RCC Dedicated Clocks configuration register, Address offset: 0x8C */ - -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - -/** - * @brief Serial Audio Interface - */ - -typedef struct -{ - __IO uint32_t GCR; /*!< SAI global configuration register, Address offset: 0x00 */ -} SAI_TypeDef; - -typedef struct -{ - __IO uint32_t CR1; /*!< SAI block x configuration register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< SAI block x configuration register 2, Address offset: 0x08 */ - __IO uint32_t FRCR; /*!< SAI block x frame configuration register, Address offset: 0x0C */ - __IO uint32_t SLOTR; /*!< SAI block x slot register, Address offset: 0x10 */ - __IO uint32_t IMR; /*!< SAI block x interrupt mask register, Address offset: 0x14 */ - __IO uint32_t SR; /*!< SAI block x status register, Address offset: 0x18 */ - __IO uint32_t CLRFR; /*!< SAI block x clear flag register, Address offset: 0x1C */ - __IO uint32_t DR; /*!< SAI block x data register, Address offset: 0x20 */ -} SAI_Block_TypeDef; - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - -/** - * @brief Crypto Processor - */ - -typedef struct -{ - __IO uint32_t CR; /*!< CRYP control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< CRYP status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< CRYP data input register, Address offset: 0x08 */ - __IO uint32_t DOUT; /*!< CRYP data output register, Address offset: 0x0C */ - __IO uint32_t DMACR; /*!< CRYP DMA control register, Address offset: 0x10 */ - __IO uint32_t IMSCR; /*!< CRYP interrupt mask set/clear register, Address offset: 0x14 */ - __IO uint32_t RISR; /*!< CRYP raw interrupt status register, Address offset: 0x18 */ - __IO uint32_t MISR; /*!< CRYP masked interrupt status register, Address offset: 0x1C */ - __IO uint32_t K0LR; /*!< CRYP key left register 0, Address offset: 0x20 */ - __IO uint32_t K0RR; /*!< CRYP key right register 0, Address offset: 0x24 */ - __IO uint32_t K1LR; /*!< CRYP key left register 1, Address offset: 0x28 */ - __IO uint32_t K1RR; /*!< CRYP key right register 1, Address offset: 0x2C */ - __IO uint32_t K2LR; /*!< CRYP key left register 2, Address offset: 0x30 */ - __IO uint32_t K2RR; /*!< CRYP key right register 2, Address offset: 0x34 */ - __IO uint32_t K3LR; /*!< CRYP key left register 3, Address offset: 0x38 */ - __IO uint32_t K3RR; /*!< CRYP key right register 3, Address offset: 0x3C */ - __IO uint32_t IV0LR; /*!< CRYP initialization vector left-word register 0, Address offset: 0x40 */ - __IO uint32_t IV0RR; /*!< CRYP initialization vector right-word register 0, Address offset: 0x44 */ - __IO uint32_t IV1LR; /*!< CRYP initialization vector left-word register 1, Address offset: 0x48 */ - __IO uint32_t IV1RR; /*!< CRYP initialization vector right-word register 1, Address offset: 0x4C */ - __IO uint32_t CSGCMCCM0R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 0, Address offset: 0x50 */ - __IO uint32_t CSGCMCCM1R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 1, Address offset: 0x54 */ - __IO uint32_t CSGCMCCM2R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 2, Address offset: 0x58 */ - __IO uint32_t CSGCMCCM3R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 3, Address offset: 0x5C */ - __IO uint32_t CSGCMCCM4R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 4, Address offset: 0x60 */ - __IO uint32_t CSGCMCCM5R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 5, Address offset: 0x64 */ - __IO uint32_t CSGCMCCM6R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 6, Address offset: 0x68 */ - __IO uint32_t CSGCMCCM7R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 7, Address offset: 0x6C */ - __IO uint32_t CSGCM0R; /*!< CRYP GCM/GMAC context swap register 0, Address offset: 0x70 */ - __IO uint32_t CSGCM1R; /*!< CRYP GCM/GMAC context swap register 1, Address offset: 0x74 */ - __IO uint32_t CSGCM2R; /*!< CRYP GCM/GMAC context swap register 2, Address offset: 0x78 */ - __IO uint32_t CSGCM3R; /*!< CRYP GCM/GMAC context swap register 3, Address offset: 0x7C */ - __IO uint32_t CSGCM4R; /*!< CRYP GCM/GMAC context swap register 4, Address offset: 0x80 */ - __IO uint32_t CSGCM5R; /*!< CRYP GCM/GMAC context swap register 5, Address offset: 0x84 */ - __IO uint32_t CSGCM6R; /*!< CRYP GCM/GMAC context swap register 6, Address offset: 0x88 */ - __IO uint32_t CSGCM7R; /*!< CRYP GCM/GMAC context swap register 7, Address offset: 0x8C */ -} CRYP_TypeDef; - -/** - * @brief HASH - */ - -typedef struct -{ - __IO uint32_t CR; /*!< HASH control register, Address offset: 0x00 */ - __IO uint32_t DIN; /*!< HASH data input register, Address offset: 0x04 */ - __IO uint32_t STR; /*!< HASH start register, Address offset: 0x08 */ - __IO uint32_t HR[5]; /*!< HASH digest registers, Address offset: 0x0C-0x1C */ - __IO uint32_t IMR; /*!< HASH interrupt enable register, Address offset: 0x20 */ - __IO uint32_t SR; /*!< HASH status register, Address offset: 0x24 */ - uint32_t RESERVED[52]; /*!< Reserved, 0x28-0xF4 */ - __IO uint32_t CSR[54]; /*!< HASH context swap registers, Address offset: 0x0F8-0x1CC */ -} HASH_TypeDef; - -/** - * @brief HASH_DIGEST - */ - -typedef struct -{ - __IO uint32_t HR[8]; /*!< HASH digest registers, Address offset: 0x310-0x32C */ -} HASH_DIGEST_TypeDef; - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - -/** - * @brief __USB_OTG_Core_register - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register 000h */ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register 004h */ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register 008h */ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register 00Ch */ - __IO uint32_t GRSTCTL; /*!< Core Reset Register 010h */ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register 014h */ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register 018h */ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register 01Ch */ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register 020h */ - __IO uint32_t GRXFSIZ; /* Receive FIFO Size Register 024h */ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register 028h*/ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg 02Ch */ - uint32_t Reserved30[2]; /* Reserved 030h*/ - __IO uint32_t GCCFG; /* General Purpose IO Register 038h*/ - __IO uint32_t CID; /* User ID Register 03Ch*/ - uint32_t Reserved40[48]; /* Reserved 040h-0FFh*/ - __IO uint32_t HPTXFSIZ; /* Host Periodic Tx FIFO Size Reg 100h*/ - __IO uint32_t DIEPTXF[0x0F];/* dev Periodic Transmit FIFO */ -} -USB_OTG_GlobalTypeDef; - - -/** - * @brief __device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /* dev Configuration Register 800h*/ - __IO uint32_t DCTL; /* dev Control Register 804h*/ - __IO uint32_t DSTS; /* dev Status Register (RO) 808h*/ - uint32_t Reserved0C; /* Reserved 80Ch*/ - __IO uint32_t DIEPMSK; /* dev IN Endpoint Mask 810h*/ - __IO uint32_t DOEPMSK; /* dev OUT Endpoint Mask 814h*/ - __IO uint32_t DAINT; /* dev All Endpoints Itr Reg 818h*/ - __IO uint32_t DAINTMSK; /* dev All Endpoints Itr Mask 81Ch*/ - uint32_t Reserved20; /* Reserved 820h*/ - uint32_t Reserved9; /* Reserved 824h*/ - __IO uint32_t DVBUSDIS; /* dev VBUS discharge Register 828h*/ - __IO uint32_t DVBUSPULSE; /* dev VBUS Pulse Register 82Ch*/ - __IO uint32_t DTHRCTL; /* dev thr 830h*/ - __IO uint32_t DIEPEMPMSK; /* dev empty msk 834h*/ - __IO uint32_t DEACHINT; /* dedicated EP interrupt 838h*/ - __IO uint32_t DEACHMSK; /* dedicated EP msk 83Ch*/ - uint32_t Reserved40; /* dedicated EP mask 840h*/ - __IO uint32_t DINEP1MSK; /* dedicated EP mask 844h*/ - uint32_t Reserved44[15]; /* Reserved 844-87Ch*/ - __IO uint32_t DOUTEP1MSK; /* dedicated EP msk 884h*/ -} -USB_OTG_DeviceTypeDef; - - -/** - * @brief __IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /* dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved 900h + (ep_num * 20h) + 04h*/ - __IO uint32_t DIEPINT; /* dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved 900h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DIEPTSIZ; /* IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h*/ - __IO uint32_t DIEPDMA; /* IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h*/ - __IO uint32_t DTXFSTS;/*IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h*/ - uint32_t Reserved18; /* Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch*/ -} -USB_OTG_INEndpointTypeDef; - - -/** - * @brief __OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /* dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /* Reserved B00h + (ep_num * 20h) + 04h*/ - __IO uint32_t DOEPINT; /* dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /* Reserved B00h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DOEPTSIZ; /* dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h*/ - __IO uint32_t DOEPDMA; /* dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h*/ - uint32_t Reserved18[2]; /* Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch*/ -} -USB_OTG_OUTEndpointTypeDef; - - -/** - * @brief __Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /* Host Configuration Register 400h*/ - __IO uint32_t HFIR; /* Host Frame Interval Register 404h*/ - __IO uint32_t HFNUM; /* Host Frame Nbr/Frame Remaining 408h*/ - uint32_t Reserved40C; /* Reserved 40Ch*/ - __IO uint32_t HPTXSTS; /* Host Periodic Tx FIFO/ Queue Status 410h*/ - __IO uint32_t HAINT; /* Host All Channels Interrupt Register 414h*/ - __IO uint32_t HAINTMSK; /* Host All Channels Interrupt Mask 418h*/ -} -USB_OTG_HostTypeDef; - -/** - * @brief __Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; - __IO uint32_t HCSPLT; - __IO uint32_t HCINT; - __IO uint32_t HCINTMSK; - __IO uint32_t HCTSIZ; - __IO uint32_t HCDMA; - uint32_t Reserved[2]; -} -USB_OTG_HostChannelTypeDef; -/** - * @} - */ - -/** @addtogroup Peripheral_memory_map - * @{ - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 2 MB) base address in the alias region */ -#define CCMDATARAM_BASE 0x10000000U /*!< CCM(core coupled memory) data RAM(64 KB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(112 KB) base address in the alias region */ -#define SRAM2_BASE 0x2001C000U /*!< SRAM2(16 KB) base address in the alias region */ -#define SRAM3_BASE 0x20020000U /*!< SRAM3(64 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define BKPSRAM_BASE 0x40024000U /*!< Backup SRAM(4 KB) base address in the alias region */ -#define FMC_R_BASE 0xA0000000U /*!< FMC registers base address */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(112 KB) base address in the bit-band region */ -#define SRAM2_BB_BASE 0x22380000U /*!< SRAM2(16 KB) base address in the bit-band region */ -#define SRAM3_BB_BASE 0x22400000U /*!< SRAM3(64 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define BKPSRAM_BB_BASE 0x42480000U /*!< Backup SRAM(4 KB) base address in the bit-band region */ -#define FLASH_END 0x081FFFFFU /*!< FLASH end address */ -#define CCMDATARAM_END 0x1000FFFFU /*!< CCM data RAM end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define TIM7_BASE (APB1PERIPH_BASE + 0x1400U) -#define TIM12_BASE (APB1PERIPH_BASE + 0x1800U) -#define TIM13_BASE (APB1PERIPH_BASE + 0x1C00U) -#define TIM14_BASE (APB1PERIPH_BASE + 0x2000U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define USART3_BASE (APB1PERIPH_BASE + 0x4800U) -#define UART4_BASE (APB1PERIPH_BASE + 0x4C00U) -#define UART5_BASE (APB1PERIPH_BASE + 0x5000U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define CAN1_BASE (APB1PERIPH_BASE + 0x6400U) -#define CAN2_BASE (APB1PERIPH_BASE + 0x6800U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) -#define DAC_BASE (APB1PERIPH_BASE + 0x7400U) -#define UART7_BASE (APB1PERIPH_BASE + 0x7800U) -#define UART8_BASE (APB1PERIPH_BASE + 0x7C00U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define TIM8_BASE (APB2PERIPH_BASE + 0x0400U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC2_BASE (APB2PERIPH_BASE + 0x2100U) -#define ADC3_BASE (APB2PERIPH_BASE + 0x2200U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SPI4_BASE (APB2PERIPH_BASE + 0x3400U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) -#define SPI5_BASE (APB2PERIPH_BASE + 0x5000U) -#define SPI6_BASE (APB2PERIPH_BASE + 0x5400U) -#define SAI1_BASE (APB2PERIPH_BASE + 0x5800U) -#define SAI1_Block_A_BASE (SAI1_BASE + 0x004U) -#define SAI1_Block_B_BASE (SAI1_BASE + 0x024U) -#define LTDC_BASE (APB2PERIPH_BASE + 0x6800U) -#define LTDC_Layer1_BASE (LTDC_BASE + 0x84U) -#define LTDC_Layer2_BASE (LTDC_BASE + 0x104U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOF_BASE (AHB1PERIPH_BASE + 0x1400U) -#define GPIOG_BASE (AHB1PERIPH_BASE + 0x1800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define GPIOI_BASE (AHB1PERIPH_BASE + 0x2000U) -#define GPIOJ_BASE (AHB1PERIPH_BASE + 0x2400U) -#define GPIOK_BASE (AHB1PERIPH_BASE + 0x2800U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) -#define ETH_BASE (AHB1PERIPH_BASE + 0x8000U) -#define ETH_MAC_BASE (ETH_BASE) -#define ETH_MMC_BASE (ETH_BASE + 0x0100U) -#define ETH_PTP_BASE (ETH_BASE + 0x0700U) -#define ETH_DMA_BASE (ETH_BASE + 0x1000U) -#define DMA2D_BASE (AHB1PERIPH_BASE + 0xB000U) - -/*!< AHB2 peripherals */ -#define DCMI_BASE (AHB2PERIPH_BASE + 0x50000U) -#define CRYP_BASE (AHB2PERIPH_BASE + 0x60000U) -#define HASH_BASE (AHB2PERIPH_BASE + 0x60400U) -#define HASH_DIGEST_BASE (AHB2PERIPH_BASE + 0x60710U) -#define RNG_BASE (AHB2PERIPH_BASE + 0x60800U) - -/*!< FMC Bankx registers base address */ -#define FMC_Bank1_R_BASE (FMC_R_BASE + 0x0000U) -#define FMC_Bank1E_R_BASE (FMC_R_BASE + 0x0104U) -#define FMC_Bank2_3_R_BASE (FMC_R_BASE + 0x0060U) -#define FMC_Bank4_R_BASE (FMC_R_BASE + 0x00A0U) -#define FMC_Bank5_6_R_BASE (FMC_R_BASE + 0x0140U) - -/* Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_HS_PERIPH_BASE 0x40040000U -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define TIM7 ((TIM_TypeDef *) TIM7_BASE) -#define TIM12 ((TIM_TypeDef *) TIM12_BASE) -#define TIM13 ((TIM_TypeDef *) TIM13_BASE) -#define TIM14 ((TIM_TypeDef *) TIM14_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define USART3 ((USART_TypeDef *) USART3_BASE) -#define UART4 ((USART_TypeDef *) UART4_BASE) -#define UART5 ((USART_TypeDef *) UART5_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define CAN1 ((CAN_TypeDef *) CAN1_BASE) -#define CAN2 ((CAN_TypeDef *) CAN2_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define DAC ((DAC_TypeDef *) DAC_BASE) -#define UART7 ((USART_TypeDef *) UART7_BASE) -#define UART8 ((USART_TypeDef *) UART8_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define TIM8 ((TIM_TypeDef *) TIM8_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define ADC2 ((ADC_TypeDef *) ADC2_BASE) -#define ADC3 ((ADC_TypeDef *) ADC3_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SPI4 ((SPI_TypeDef *) SPI4_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define SPI5 ((SPI_TypeDef *) SPI5_BASE) -#define SPI6 ((SPI_TypeDef *) SPI6_BASE) -#define SAI1 ((SAI_TypeDef *) SAI1_BASE) -#define SAI1_Block_A ((SAI_Block_TypeDef *)SAI1_Block_A_BASE) -#define SAI1_Block_B ((SAI_Block_TypeDef *)SAI1_Block_B_BASE) -#define LTDC ((LTDC_TypeDef *)LTDC_BASE) -#define LTDC_Layer1 ((LTDC_Layer_TypeDef *)LTDC_Layer1_BASE) -#define LTDC_Layer2 ((LTDC_Layer_TypeDef *)LTDC_Layer2_BASE) - -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOF ((GPIO_TypeDef *) GPIOF_BASE) -#define GPIOG ((GPIO_TypeDef *) GPIOG_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define GPIOI ((GPIO_TypeDef *) GPIOI_BASE) -#define GPIOJ ((GPIO_TypeDef *) GPIOJ_BASE) -#define GPIOK ((GPIO_TypeDef *) GPIOK_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define ETH ((ETH_TypeDef *) ETH_BASE) -#define DMA2D ((DMA2D_TypeDef *)DMA2D_BASE) -#define DCMI ((DCMI_TypeDef *) DCMI_BASE) -#define CRYP ((CRYP_TypeDef *) CRYP_BASE) -#define HASH ((HASH_TypeDef *) HASH_BASE) -#define HASH_DIGEST ((HASH_DIGEST_TypeDef *) HASH_DIGEST_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) -#define FMC_Bank1 ((FMC_Bank1_TypeDef *) FMC_Bank1_R_BASE) -#define FMC_Bank1E ((FMC_Bank1E_TypeDef *) FMC_Bank1E_R_BASE) -#define FMC_Bank2_3 ((FMC_Bank2_3_TypeDef *) FMC_Bank2_3_R_BASE) -#define FMC_Bank4 ((FMC_Bank4_TypeDef *) FMC_Bank4_R_BASE) -#define FMC_Bank5_6 ((FMC_Bank5_6_TypeDef *) FMC_Bank5_6_R_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) -#define USB_OTG_HS ((USB_OTG_GlobalTypeDef *) USB_OTG_HS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS_Device - * @{ - */ - -/** @addtogroup stm32f446xx - * @{ - */ - -#ifndef __STM32F446xx_H -#define __STM32F446xx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1, ADC2 and ADC3 global Interrupts */ - CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */ - CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */ - CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ - CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - USART3_IRQn = 39, /*!< USART3 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */ - TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */ - TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */ - TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare global interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - FMC_IRQn = 48, /*!< FMC global Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - UART4_IRQn = 52, /*!< UART4 global Interrupt */ - UART5_IRQn = 53, /*!< UART5 global Interrupt */ - TIM6_DAC_IRQn = 54, /*!< TIM6 global and DAC1&2 underrun error interrupts */ - TIM7_IRQn = 55, /*!< TIM7 global interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */ - CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */ - CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */ - CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - OTG_HS_EP1_OUT_IRQn = 74, /*!< USB OTG HS End Point 1 Out global interrupt */ - OTG_HS_EP1_IN_IRQn = 75, /*!< USB OTG HS End Point 1 In global interrupt */ - OTG_HS_WKUP_IRQn = 76, /*!< USB OTG HS Wakeup through EXTI interrupt */ - OTG_HS_IRQn = 77, /*!< USB OTG HS global interrupt */ - DCMI_IRQn = 78, /*!< DCMI global interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - SPI4_IRQn = 84, /*!< SPI4 global Interrupt */ - SAI1_IRQn = 87, /*!< SAI1 global Interrupt */ - SAI2_IRQn = 91, /*!< SAI2 global Interrupt */ - QUADSPI_IRQn = 92, /*!< QuadSPI global Interrupt */ - CEC_IRQn = 93, /*!< CEC global Interrupt */ - SPDIF_RX_IRQn = 94, /*!< SPDIF-RX global Interrupt */ - FMPI2C1_EV_IRQn = 95, /*!< FMPI2C1 Event Interrupt */ - FMPI2C1_ER_IRQn = 96 /*!< FMPI2C1 Error Interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - - -/** - * @brief Controller Area Network TxMailBox - */ - -typedef struct -{ - __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ - __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ - __IO uint32_t TDLR; /*!< CAN mailbox data low register */ - __IO uint32_t TDHR; /*!< CAN mailbox data high register */ -} CAN_TxMailBox_TypeDef; - -/** - * @brief Controller Area Network FIFOMailBox - */ - -typedef struct -{ - __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ - __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ - __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ - __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ -} CAN_FIFOMailBox_TypeDef; - -/** - * @brief Controller Area Network FilterRegister - */ - -typedef struct -{ - __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ - __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ -} CAN_FilterRegister_TypeDef; - -/** - * @brief Controller Area Network - */ - -typedef struct -{ - __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ - __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ - __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ - __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ - __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ - __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ - __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ - __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ - uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ - CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ - CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ - uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ - __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ - __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ - uint32_t RESERVED2; /*!< Reserved, 0x208 */ - __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ - uint32_t RESERVED3; /*!< Reserved, 0x210 */ - __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ - uint32_t RESERVED4; /*!< Reserved, 0x218 */ - __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ - uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ - CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ -} CAN_TypeDef; - -/** - * @brief Consumer Electronics Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< CEC control register, Address offset:0x00 */ - __IO uint32_t CFGR; /*!< CEC configuration register, Address offset:0x04 */ - __IO uint32_t TXDR; /*!< CEC Tx data register , Address offset:0x08 */ - __IO uint32_t RXDR; /*!< CEC Rx Data Register, Address offset:0x0C */ - __IO uint32_t ISR; /*!< CEC Interrupt and Status Register, Address offset:0x10 */ - __IO uint32_t IER; /*!< CEC interrupt enable register, Address offset:0x14 */ -} CEC_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Digital to Analog Converter - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ - __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ - __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ - __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ - __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ - __IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */ - __IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */ - __IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */ - __IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */ - __IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */ - __IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */ - __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ - __IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */ - __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ -} DAC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - -/** - * @brief DCMI - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DCMI control register 1, Address offset: 0x00 */ - __IO uint32_t SR; /*!< DCMI status register, Address offset: 0x04 */ - __IO uint32_t RISR; /*!< DCMI raw interrupt status register, Address offset: 0x08 */ - __IO uint32_t IER; /*!< DCMI interrupt enable register, Address offset: 0x0C */ - __IO uint32_t MISR; /*!< DCMI masked interrupt status register, Address offset: 0x10 */ - __IO uint32_t ICR; /*!< DCMI interrupt clear register, Address offset: 0x14 */ - __IO uint32_t ESCR; /*!< DCMI embedded synchronization code register, Address offset: 0x18 */ - __IO uint32_t ESUR; /*!< DCMI embedded synchronization unmask register, Address offset: 0x1C */ - __IO uint32_t CWSTRTR; /*!< DCMI crop window start, Address offset: 0x20 */ - __IO uint32_t CWSIZER; /*!< DCMI crop window size, Address offset: 0x24 */ - __IO uint32_t DR; /*!< DCMI data register, Address offset: 0x28 */ -} DCMI_TypeDef; - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief Flexible Memory Controller - */ - -typedef struct -{ - __IO uint32_t BTCR[8]; /*!< NOR/PSRAM chip-select control register(BCR) and chip-select timing register(BTR), Address offset: 0x00-1C */ -} FMC_Bank1_TypeDef; - -/** - * @brief Flexible Memory Controller Bank1E - */ - -typedef struct -{ - __IO uint32_t BWTR[7]; /*!< NOR/PSRAM write timing registers, Address offset: 0x104-0x11C */ -} FMC_Bank1E_TypeDef; - -/** - * @brief Flexible Memory Controller Bank3 - */ - -typedef struct -{ - __IO uint32_t PCR; /*!< NAND Flash control register, Address offset: 0x80 */ - __IO uint32_t SR; /*!< NAND Flash FIFO status and interrupt register, Address offset: 0x84 */ - __IO uint32_t PMEM; /*!< NAND Flash Common memory space timing register, Address offset: 0x88 */ - __IO uint32_t PATT; /*!< NAND Flash Attribute memory space timing register, Address offset: 0x8C */ - uint32_t RESERVED; /*!< Reserved, 0x90 */ - __IO uint32_t ECCR; /*!< NAND Flash ECC result registers, Address offset: 0x94 */ -} FMC_Bank3_TypeDef; - -/** - * @brief Flexible Memory Controller Bank5_6 - */ - -typedef struct -{ - __IO uint32_t SDCR[2]; /*!< SDRAM Control registers , Address offset: 0x140-0x144 */ - __IO uint32_t SDTR[2]; /*!< SDRAM Timing registers , Address offset: 0x148-0x14C */ - __IO uint32_t SDCMR; /*!< SDRAM Command Mode register, Address offset: 0x150 */ - __IO uint32_t SDRTR; /*!< SDRAM Refresh Timer register, Address offset: 0x154 */ - __IO uint32_t SDSR; /*!< SDRAM Status register, Address offset: 0x158 */ -} FMC_Bank5_6_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x24-0x28 */ - __IO uint32_t CFGR; /*!< SYSCFG Configuration register, Address offset: 0x2C */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< FMPI2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< FMPI2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< FMPI2C Own address 1 register, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< FMPI2C Own address 2 register, Address offset: 0x0C */ - __IO uint32_t TIMINGR; /*!< FMPI2C Timing register, Address offset: 0x10 */ - __IO uint32_t TIMEOUTR; /*!< FMPI2C Timeout register, Address offset: 0x14 */ - __IO uint32_t ISR; /*!< FMPI2C Interrupt and status register, Address offset: 0x18 */ - __IO uint32_t ICR; /*!< FMPI2C Interrupt clear register, Address offset: 0x1C */ - __IO uint32_t PECR; /*!< FMPI2C PEC register, Address offset: 0x20 */ - __IO uint32_t RXDR; /*!< FMPI2C Receive data register, Address offset: 0x24 */ - __IO uint32_t TXDR; /*!< FMPI2C Transmit data register, Address offset: 0x28 */ -} FMPI2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - __IO uint32_t PLLSAICFGR; /*!< RCC PLLSAI configuration register, Address offset: 0x88 */ - __IO uint32_t DCKCFGR; /*!< RCC Dedicated Clocks configuration register, Address offset: 0x8C */ - __IO uint32_t CKGATENR; /*!< RCC Clocks Gated ENable Register, Address offset: 0x90 */ - __IO uint32_t DCKCFGR2; /*!< RCC Dedicated Clocks configuration register 2, Address offset: 0x94 */ -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - -/** - * @brief Serial Audio Interface - */ - -typedef struct -{ - __IO uint32_t GCR; /*!< SAI global configuration register, Address offset: 0x00 */ -} SAI_TypeDef; - -typedef struct -{ - __IO uint32_t CR1; /*!< SAI block x configuration register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< SAI block x configuration register 2, Address offset: 0x08 */ - __IO uint32_t FRCR; /*!< SAI block x frame configuration register, Address offset: 0x0C */ - __IO uint32_t SLOTR; /*!< SAI block x slot register, Address offset: 0x10 */ - __IO uint32_t IMR; /*!< SAI block x interrupt mask register, Address offset: 0x14 */ - __IO uint32_t SR; /*!< SAI block x status register, Address offset: 0x18 */ - __IO uint32_t CLRFR; /*!< SAI block x clear flag register, Address offset: 0x1C */ - __IO uint32_t DR; /*!< SAI block x data register, Address offset: 0x20 */ -} SAI_Block_TypeDef; - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief QUAD Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR; /*!< QUADSPI Control register, Address offset: 0x00 */ - __IO uint32_t DCR; /*!< QUADSPI Device Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< QUADSPI Status register, Address offset: 0x08 */ - __IO uint32_t FCR; /*!< QUADSPI Flag Clear register, Address offset: 0x0C */ - __IO uint32_t DLR; /*!< QUADSPI Data Length register, Address offset: 0x10 */ - __IO uint32_t CCR; /*!< QUADSPI Communication Configuration register, Address offset: 0x14 */ - __IO uint32_t AR; /*!< QUADSPI Address register, Address offset: 0x18 */ - __IO uint32_t ABR; /*!< QUADSPI Alternate Bytes register, Address offset: 0x1C */ - __IO uint32_t DR; /*!< QUADSPI Data register, Address offset: 0x20 */ - __IO uint32_t PSMKR; /*!< QUADSPI Polling Status Mask register, Address offset: 0x24 */ - __IO uint32_t PSMAR; /*!< QUADSPI Polling Status Match register, Address offset: 0x28 */ - __IO uint32_t PIR; /*!< QUADSPI Polling Interval register, Address offset: 0x2C */ - __IO uint32_t LPTR; /*!< QUADSPI Low Power Timeout register, Address offset: 0x30 */ -} QUADSPI_TypeDef; - -/** - * @brief SPDIFRX Interface - */ - -typedef struct -{ - __IO uint32_t CR; /*!< Control register, Address offset: 0x00 */ - __IO uint16_t IMR; /*!< Interrupt mask register, Address offset: 0x04 */ - uint16_t RESERVED0; /*!< Reserved, 0x06 */ - __IO uint32_t SR; /*!< Status register, Address offset: 0x08 */ - __IO uint16_t IFCR; /*!< Interrupt Flag Clear register, Address offset: 0x0C */ - uint16_t RESERVED1; /*!< Reserved, 0x0E */ - __IO uint32_t DR; /*!< Data input register, Address offset: 0x10 */ - __IO uint32_t CSR; /*!< Channel Status register, Address offset: 0x14 */ - __IO uint32_t DIR; /*!< Debug Information register, Address offset: 0x18 */ - uint16_t RESERVED2; /*!< Reserved, 0x1A */ -} SPDIFRX_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - -/** - * @brief USB_OTG_Core_Registers - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register 000h */ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register 004h */ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register 008h */ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register 00Ch */ - __IO uint32_t GRSTCTL; /*!< Core Reset Register 010h */ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register 014h */ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register 018h */ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register 01Ch */ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register 020h */ - __IO uint32_t GRXFSIZ; /*!< Receive FIFO Size Register 024h */ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register 028h */ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg 02Ch */ - uint32_t Reserved30[2]; /*!< Reserved 030h */ - __IO uint32_t GCCFG; /*!< General Purpose IO Register 038h */ - __IO uint32_t CID; /*!< User ID Register 03Ch */ - uint32_t Reserved5[3]; /*!< Reserved 040h-048h */ - __IO uint32_t GHWCFG3; /*!< User HW config3 04Ch */ - uint32_t Reserved6; /*!< Reserved 050h */ - __IO uint32_t GLPMCFG; /*!< LPM Register 054h */ - uint32_t Reserved; /*!< Reserved 058h */ - __IO uint32_t GDFIFOCFG; /*!< DFIFO Software Config Register 05Ch */ - uint32_t Reserved43[40]; /*!< Reserved 058h-0FFh */ - __IO uint32_t HPTXFSIZ; /*!< Host Periodic Tx FIFO Size Reg 100h */ - __IO uint32_t DIEPTXF[0x0F]; /*!< dev Periodic Transmit FIFO */ -} USB_OTG_GlobalTypeDef; - -/** - * @brief USB_OTG_device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /*!< dev Configuration Register 800h */ - __IO uint32_t DCTL; /*!< dev Control Register 804h */ - __IO uint32_t DSTS; /*!< dev Status Register (RO) 808h */ - uint32_t Reserved0C; /*!< Reserved 80Ch */ - __IO uint32_t DIEPMSK; /*!< dev IN Endpoint Mask 810h */ - __IO uint32_t DOEPMSK; /*!< dev OUT Endpoint Mask 814h */ - __IO uint32_t DAINT; /*!< dev All Endpoints Itr Reg 818h */ - __IO uint32_t DAINTMSK; /*!< dev All Endpoints Itr Mask 81Ch */ - uint32_t Reserved20; /*!< Reserved 820h */ - uint32_t Reserved9; /*!< Reserved 824h */ - __IO uint32_t DVBUSDIS; /*!< dev VBUS discharge Register 828h */ - __IO uint32_t DVBUSPULSE; /*!< dev VBUS Pulse Register 82Ch */ - __IO uint32_t DTHRCTL; /*!< dev threshold 830h */ - __IO uint32_t DIEPEMPMSK; /*!< dev empty msk 834h */ - __IO uint32_t DEACHINT; /*!< dedicated EP interrupt 838h */ - __IO uint32_t DEACHMSK; /*!< dedicated EP msk 83Ch */ - uint32_t Reserved40; /*!< dedicated EP mask 840h */ - __IO uint32_t DINEP1MSK; /*!< dedicated EP mask 844h */ - uint32_t Reserved44[15]; /*!< Reserved 844-87Ch */ - __IO uint32_t DOUTEP1MSK; /*!< dedicated EP msk 884h */ -} USB_OTG_DeviceTypeDef; - -/** - * @brief USB_OTG_IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /*!< dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /*!< Reserved 900h + (ep_num * 20h) + 04h */ - __IO uint32_t DIEPINT; /*!< dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /*!< Reserved 900h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DIEPTSIZ; /*!< IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h */ - __IO uint32_t DIEPDMA; /*!< IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h */ - __IO uint32_t DTXFSTS; /*!< IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h */ - uint32_t Reserved18; /*!< Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch */ -} USB_OTG_INEndpointTypeDef; - -/** - * @brief USB_OTG_OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /*!< dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /*!< Reserved B00h + (ep_num * 20h) + 04h */ - __IO uint32_t DOEPINT; /*!< dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /*!< Reserved B00h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DOEPTSIZ; /*!< dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h */ - __IO uint32_t DOEPDMA; /*!< dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h */ - uint32_t Reserved18[2]; /*!< Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch */ -} USB_OTG_OUTEndpointTypeDef; - -/** - * @brief USB_OTG_Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /*!< Host Configuration Register 400h */ - __IO uint32_t HFIR; /*!< Host Frame Interval Register 404h */ - __IO uint32_t HFNUM; /*!< Host Frame Nbr/Frame Remaining 408h */ - uint32_t Reserved40C; /*!< Reserved 40Ch */ - __IO uint32_t HPTXSTS; /*!< Host Periodic Tx FIFO/ Queue Status 410h */ - __IO uint32_t HAINT; /*!< Host All Channels Interrupt Register 414h */ - __IO uint32_t HAINTMSK; /*!< Host All Channels Interrupt Mask 418h */ -} USB_OTG_HostTypeDef; - -/** - * @brief USB_OTG_Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; /*!< Host Channel Characteristics Register 500h */ - __IO uint32_t HCSPLT; /*!< Host Channel Split Control Register 504h */ - __IO uint32_t HCINT; /*!< Host Channel Interrupt Register 508h */ - __IO uint32_t HCINTMSK; /*!< Host Channel Interrupt Mask Register 50Ch */ - __IO uint32_t HCTSIZ; /*!< Host Channel Transfer Size Register 510h */ - __IO uint32_t HCDMA; /*!< Host Channel DMA Address Register 514h */ - uint32_t Reserved[2]; /*!< Reserved */ -} USB_OTG_HostChannelTypeDef; - -/** - * @} - */ - -/** @addtogroup Peripheral_memory_map - * @{ - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(112 KB) base address in the alias region */ -#define SRAM2_BASE 0x2001C000U /*!< SRAM2(16 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define BKPSRAM_BASE 0x40024000U /*!< Backup SRAM(4 KB) base address in the alias region */ -#define FMC_R_BASE 0xA0000000U /*!< FMC registers base address */ -#define QSPI_R_BASE 0xA0001000U /*!< QuadSPI registers base address */ - -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(112 KB) base address in the bit-band region */ -#define SRAM2_BB_BASE 0x22380000U /*!< SRAM2(16 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define BKPSRAM_BB_BASE 0x42480000U /*!< Backup SRAM(4 KB) base address in the bit-band region */ -#define FLASH_END 0x0807FFFFU /*!< FLASH end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define TIM7_BASE (APB1PERIPH_BASE + 0x1400U) -#define TIM12_BASE (APB1PERIPH_BASE + 0x1800U) -#define TIM13_BASE (APB1PERIPH_BASE + 0x1C00U) -#define TIM14_BASE (APB1PERIPH_BASE + 0x2000U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define SPDIFRX_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define USART3_BASE (APB1PERIPH_BASE + 0x4800U) -#define UART4_BASE (APB1PERIPH_BASE + 0x4C00U) -#define UART5_BASE (APB1PERIPH_BASE + 0x5000U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define FMPI2C1_BASE (APB1PERIPH_BASE + 0x6000U) -#define CAN1_BASE (APB1PERIPH_BASE + 0x6400U) -#define CAN2_BASE (APB1PERIPH_BASE + 0x6800U) -#define CEC_BASE (APB1PERIPH_BASE + 0x6C00U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) -#define DAC_BASE (APB1PERIPH_BASE + 0x7400U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define TIM8_BASE (APB2PERIPH_BASE + 0x0400U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC2_BASE (APB2PERIPH_BASE + 0x2100U) -#define ADC3_BASE (APB2PERIPH_BASE + 0x2200U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SPI4_BASE (APB2PERIPH_BASE + 0x3400U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) -#define SAI1_BASE (APB2PERIPH_BASE + 0x5800U) -#define SAI1_Block_A_BASE (SAI1_BASE + 0x004U) -#define SAI1_Block_B_BASE (SAI1_BASE + 0x024U) -#define SAI2_BASE (APB2PERIPH_BASE + 0x5C00U) -#define SAI2_Block_A_BASE (SAI2_BASE + 0x004U) -#define SAI2_Block_B_BASE (SAI2_BASE + 0x024U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOF_BASE (AHB1PERIPH_BASE + 0x1400U) -#define GPIOG_BASE (AHB1PERIPH_BASE + 0x1800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) - -/*!< AHB2 peripherals */ -#define DCMI_BASE (AHB2PERIPH_BASE + 0x50000U) - -/*!< FMC Bankx registers base address */ -#define FMC_Bank1_R_BASE (FMC_R_BASE + 0x0000U) -#define FMC_Bank1E_R_BASE (FMC_R_BASE + 0x0104U) -#define FMC_Bank3_R_BASE (FMC_R_BASE + 0x0080U) -#define FMC_Bank5_6_R_BASE (FMC_R_BASE + 0x0140U) - -/*!< Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_HS_PERIPH_BASE 0x40040000U -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define TIM7 ((TIM_TypeDef *) TIM7_BASE) -#define TIM12 ((TIM_TypeDef *) TIM12_BASE) -#define TIM13 ((TIM_TypeDef *) TIM13_BASE) -#define TIM14 ((TIM_TypeDef *) TIM14_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define SPDIFRX ((SPDIFRX_TypeDef *) SPDIFRX_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define USART3 ((USART_TypeDef *) USART3_BASE) -#define UART4 ((USART_TypeDef *) UART4_BASE) -#define UART5 ((USART_TypeDef *) UART5_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define FMPI2C1 ((FMPI2C_TypeDef *) FMPI2C1_BASE) -#define CAN1 ((CAN_TypeDef *) CAN1_BASE) -#define CAN2 ((CAN_TypeDef *) CAN2_BASE) -#define CEC ((CEC_TypeDef *) CEC_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define DAC ((DAC_TypeDef *) DAC_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define TIM8 ((TIM_TypeDef *) TIM8_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define ADC2 ((ADC_TypeDef *) ADC2_BASE) -#define ADC3 ((ADC_TypeDef *) ADC3_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SPI4 ((SPI_TypeDef *) SPI4_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define SAI1 ((SAI_TypeDef *) SAI1_BASE) -#define SAI1_Block_A ((SAI_Block_TypeDef *)SAI1_Block_A_BASE) -#define SAI1_Block_B ((SAI_Block_TypeDef *)SAI1_Block_B_BASE) -#define SAI2 ((SAI_TypeDef *) SAI2_BASE) -#define SAI2_Block_A ((SAI_Block_TypeDef *)SAI2_Block_A_BASE) -#define SAI2_Block_B ((SAI_Block_TypeDef *)SAI2_Block_B_BASE) - -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOF ((GPIO_TypeDef *) GPIOF_BASE) -#define GPIOG ((GPIO_TypeDef *) GPIOG_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define DCMI ((DCMI_TypeDef *) DCMI_BASE) -#define FMC_Bank1 ((FMC_Bank1_TypeDef *) FMC_Bank1_R_BASE) -#define FMC_Bank1E ((FMC_Bank1E_TypeDef *) FMC_Bank1E_R_BASE) -#define FMC_Bank3 ((FMC_Bank3_TypeDef *) FMC_Bank3_R_BASE) -#define FMC_Bank5_6 ((FMC_Bank5_6_TypeDef *) FMC_Bank5_6_R_BASE) -#define QUADSPI ((QUADSPI_TypeDef *) QSPI_R_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) -#define USB_OTG_HS ((USB_OTG_GlobalTypeDef *) USB_OTG_HS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS_Device - * @{ - */ - -/** @addtogroup stm32f469xx - * @{ - */ - -#ifndef __STM32F469xx_H -#define __STM32F469xx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1, ADC2 and ADC3 global Interrupts */ - CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */ - CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */ - CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ - CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - USART3_IRQn = 39, /*!< USART3 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */ - TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */ - TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */ - TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare global interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - FMC_IRQn = 48, /*!< FMC global Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - UART4_IRQn = 52, /*!< UART4 global Interrupt */ - UART5_IRQn = 53, /*!< UART5 global Interrupt */ - TIM6_DAC_IRQn = 54, /*!< TIM6 global and DAC1&2 underrun error interrupts */ - TIM7_IRQn = 55, /*!< TIM7 global interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - ETH_IRQn = 61, /*!< Ethernet global Interrupt */ - ETH_WKUP_IRQn = 62, /*!< Ethernet Wakeup through EXTI line Interrupt */ - CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */ - CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */ - CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */ - CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - OTG_HS_EP1_OUT_IRQn = 74, /*!< USB OTG HS End Point 1 Out global interrupt */ - OTG_HS_EP1_IN_IRQn = 75, /*!< USB OTG HS End Point 1 In global interrupt */ - OTG_HS_WKUP_IRQn = 76, /*!< USB OTG HS Wakeup through EXTI interrupt */ - OTG_HS_IRQn = 77, /*!< USB OTG HS global interrupt */ - DCMI_IRQn = 78, /*!< DCMI global interrupt */ - HASH_RNG_IRQn = 80, /*!< Hash and Rng global interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - UART7_IRQn = 82, /*!< UART7 global interrupt */ - UART8_IRQn = 83, /*!< UART8 global interrupt */ - SPI4_IRQn = 84, /*!< SPI4 global Interrupt */ - SPI5_IRQn = 85, /*!< SPI5 global Interrupt */ - SPI6_IRQn = 86, /*!< SPI6 global Interrupt */ - SAI1_IRQn = 87, /*!< SAI1 global Interrupt */ - LTDC_IRQn = 88, /*!< LTDC global Interrupt */ - LTDC_ER_IRQn = 89, /*!< LTDC Error global Interrupt */ - DMA2D_IRQn = 90, /*!< DMA2D global Interrupt */ - QUADSPI_IRQn = 91, /*!< QUADSPI global Interrupt */ - DSI_IRQn = 92 /*!< DSI global Interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - - -/** - * @brief Controller Area Network TxMailBox - */ - -typedef struct -{ - __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ - __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ - __IO uint32_t TDLR; /*!< CAN mailbox data low register */ - __IO uint32_t TDHR; /*!< CAN mailbox data high register */ -} CAN_TxMailBox_TypeDef; - -/** - * @brief Controller Area Network FIFOMailBox - */ - -typedef struct -{ - __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ - __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ - __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ - __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ -} CAN_FIFOMailBox_TypeDef; - -/** - * @brief Controller Area Network FilterRegister - */ - -typedef struct -{ - __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ - __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ -} CAN_FilterRegister_TypeDef; - -/** - * @brief Controller Area Network - */ - -typedef struct -{ - __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ - __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ - __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ - __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ - __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ - __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ - __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ - __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ - uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ - CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ - CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ - uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ - __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ - __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ - uint32_t RESERVED2; /*!< Reserved, 0x208 */ - __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ - uint32_t RESERVED3; /*!< Reserved, 0x210 */ - __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ - uint32_t RESERVED4; /*!< Reserved, 0x218 */ - __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ - uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ - CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ -} CAN_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Digital to Analog Converter - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ - __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ - __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ - __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ - __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ - __IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */ - __IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */ - __IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */ - __IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */ - __IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */ - __IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */ - __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ - __IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */ - __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ -} DAC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - -/** - * @brief DCMI - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DCMI control register 1, Address offset: 0x00 */ - __IO uint32_t SR; /*!< DCMI status register, Address offset: 0x04 */ - __IO uint32_t RISR; /*!< DCMI raw interrupt status register, Address offset: 0x08 */ - __IO uint32_t IER; /*!< DCMI interrupt enable register, Address offset: 0x0C */ - __IO uint32_t MISR; /*!< DCMI masked interrupt status register, Address offset: 0x10 */ - __IO uint32_t ICR; /*!< DCMI interrupt clear register, Address offset: 0x14 */ - __IO uint32_t ESCR; /*!< DCMI embedded synchronization code register, Address offset: 0x18 */ - __IO uint32_t ESUR; /*!< DCMI embedded synchronization unmask register, Address offset: 0x1C */ - __IO uint32_t CWSTRTR; /*!< DCMI crop window start, Address offset: 0x20 */ - __IO uint32_t CWSIZER; /*!< DCMI crop window size, Address offset: 0x24 */ - __IO uint32_t DR; /*!< DCMI data register, Address offset: 0x28 */ -} DCMI_TypeDef; - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - -/** - * @brief DMA2D Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA2D Control Register, Address offset: 0x00 */ - __IO uint32_t ISR; /*!< DMA2D Interrupt Status Register, Address offset: 0x04 */ - __IO uint32_t IFCR; /*!< DMA2D Interrupt Flag Clear Register, Address offset: 0x08 */ - __IO uint32_t FGMAR; /*!< DMA2D Foreground Memory Address Register, Address offset: 0x0C */ - __IO uint32_t FGOR; /*!< DMA2D Foreground Offset Register, Address offset: 0x10 */ - __IO uint32_t BGMAR; /*!< DMA2D Background Memory Address Register, Address offset: 0x14 */ - __IO uint32_t BGOR; /*!< DMA2D Background Offset Register, Address offset: 0x18 */ - __IO uint32_t FGPFCCR; /*!< DMA2D Foreground PFC Control Register, Address offset: 0x1C */ - __IO uint32_t FGCOLR; /*!< DMA2D Foreground Color Register, Address offset: 0x20 */ - __IO uint32_t BGPFCCR; /*!< DMA2D Background PFC Control Register, Address offset: 0x24 */ - __IO uint32_t BGCOLR; /*!< DMA2D Background Color Register, Address offset: 0x28 */ - __IO uint32_t FGCMAR; /*!< DMA2D Foreground CLUT Memory Address Register, Address offset: 0x2C */ - __IO uint32_t BGCMAR; /*!< DMA2D Background CLUT Memory Address Register, Address offset: 0x30 */ - __IO uint32_t OPFCCR; /*!< DMA2D Output PFC Control Register, Address offset: 0x34 */ - __IO uint32_t OCOLR; /*!< DMA2D Output Color Register, Address offset: 0x38 */ - __IO uint32_t OMAR; /*!< DMA2D Output Memory Address Register, Address offset: 0x3C */ - __IO uint32_t OOR; /*!< DMA2D Output Offset Register, Address offset: 0x40 */ - __IO uint32_t NLR; /*!< DMA2D Number of Line Register, Address offset: 0x44 */ - __IO uint32_t LWR; /*!< DMA2D Line Watermark Register, Address offset: 0x48 */ - __IO uint32_t AMTCR; /*!< DMA2D AHB Master Timer Configuration Register, Address offset: 0x4C */ - uint32_t RESERVED[236]; /*!< Reserved, 0x50-0x3FF */ - __IO uint32_t FGCLUT[256]; /*!< DMA2D Foreground CLUT, Address offset:400-7FF */ - __IO uint32_t BGCLUT[256]; /*!< DMA2D Background CLUT, Address offset:800-BFF */ -} DMA2D_TypeDef; - -/** - * @brief DSI Controller - */ - -typedef struct -{ - __IO uint32_t VR; /*!< DSI Host Version Register, Address offset: 0x00 */ - __IO uint32_t CR; /*!< DSI Host Control Register, Address offset: 0x04 */ - __IO uint32_t CCR; /*!< DSI HOST Clock Control Register, Address offset: 0x08 */ - __IO uint32_t LVCIDR; /*!< DSI Host LTDC VCID Register, Address offset: 0x0C */ - __IO uint32_t LCOLCR; /*!< DSI Host LTDC Color Coding Register, Address offset: 0x10 */ - __IO uint32_t LPCR; /*!< DSI Host LTDC Polarity Configuration Register, Address offset: 0x14 */ - __IO uint32_t LPMCR; /*!< DSI Host Low-Power Mode Configuration Register, Address offset: 0x18 */ - uint32_t RESERVED0[4]; /*!< Reserved, 0x1C - 0x2B */ - __IO uint32_t PCR; /*!< DSI Host Protocol Configuration Register, Address offset: 0x2C */ - __IO uint32_t GVCIDR; /*!< DSI Host Generic VCID Register, Address offset: 0x30 */ - __IO uint32_t MCR; /*!< DSI Host Mode Configuration Register, Address offset: 0x34 */ - __IO uint32_t VMCR; /*!< DSI Host Video Mode Configuration Register, Address offset: 0x38 */ - __IO uint32_t VPCR; /*!< DSI Host Video Packet Configuration Register, Address offset: 0x3C */ - __IO uint32_t VCCR; /*!< DSI Host Video Chunks Configuration Register, Address offset: 0x40 */ - __IO uint32_t VNPCR; /*!< DSI Host Video Null Packet Configuration Register, Address offset: 0x44 */ - __IO uint32_t VHSACR; /*!< DSI Host Video HSA Configuration Register, Address offset: 0x48 */ - __IO uint32_t VHBPCR; /*!< DSI Host Video HBP Configuration Register, Address offset: 0x4C */ - __IO uint32_t VLCR; /*!< DSI Host Video Line Configuration Register, Address offset: 0x50 */ - __IO uint32_t VVSACR; /*!< DSI Host Video VSA Configuration Register, Address offset: 0x54 */ - __IO uint32_t VVBPCR; /*!< DSI Host Video VBP Configuration Register, Address offset: 0x58 */ - __IO uint32_t VVFPCR; /*!< DSI Host Video VFP Configuration Register, Address offset: 0x5C */ - __IO uint32_t VVACR; /*!< DSI Host Video VA Configuration Register, Address offset: 0x60 */ - __IO uint32_t LCCR; /*!< DSI Host LTDC Command Configuration Register, Address offset: 0x64 */ - __IO uint32_t CMCR; /*!< DSI Host Command Mode Configuration Register, Address offset: 0x68 */ - __IO uint32_t GHCR; /*!< DSI Host Generic Header Configuration Register, Address offset: 0x6C */ - __IO uint32_t GPDR; /*!< DSI Host Generic Payload Data Register, Address offset: 0x70 */ - __IO uint32_t GPSR; /*!< DSI Host Generic Packet Status Register, Address offset: 0x74 */ - __IO uint32_t TCCR[6]; /*!< DSI Host Timeout Counter Configuration Register, Address offset: 0x78-0x8F */ - __IO uint32_t TDCR; /*!< DSI Host 3D Configuration Register, Address offset: 0x90 */ - __IO uint32_t CLCR; /*!< DSI Host Clock Lane Configuration Register, Address offset: 0x94 */ - __IO uint32_t CLTCR; /*!< DSI Host Clock Lane Timer Configuration Register, Address offset: 0x98 */ - __IO uint32_t DLTCR; /*!< DSI Host Data Lane Timer Configuration Register, Address offset: 0x9C */ - __IO uint32_t PCTLR; /*!< DSI Host PHY Control Register, Address offset: 0xA0 */ - __IO uint32_t PCONFR; /*!< DSI Host PHY Configuration Register, Address offset: 0xA4 */ - __IO uint32_t PUCR; /*!< DSI Host PHY ULPS Control Register, Address offset: 0xA8 */ - __IO uint32_t PTTCR; /*!< DSI Host PHY TX Triggers Configuration Register, Address offset: 0xAC */ - __IO uint32_t PSR; /*!< DSI Host PHY Status Register, Address offset: 0xB0 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0xB4 - 0xBB */ - __IO uint32_t ISR[2]; /*!< DSI Host Interrupt & Status Register, Address offset: 0xBC-0xC3 */ - __IO uint32_t IER[2]; /*!< DSI Host Interrupt Enable Register, Address offset: 0xC4-0xCB */ - uint32_t RESERVED2[3]; /*!< Reserved, 0xD0 - 0xD7 */ - __IO uint32_t FIR[2]; /*!< DSI Host Force Interrupt Register, Address offset: 0xD8-0xDF */ - uint32_t RESERVED3[8]; /*!< Reserved, 0xE0 - 0xFF */ - __IO uint32_t VSCR; /*!< DSI Host Video Shadow Control Register, Address offset: 0x100 */ - uint32_t RESERVED4[2]; /*!< Reserved, 0x104 - 0x10B */ - __IO uint32_t LCVCIDR; /*!< DSI Host LTDC Current VCID Register, Address offset: 0x10C */ - __IO uint32_t LCCCR; /*!< DSI Host LTDC Current Color Coding Register, Address offset: 0x110 */ - uint32_t RESERVED5; /*!< Reserved, 0x114 */ - __IO uint32_t LPMCCR; /*!< DSI Host Low-power Mode Current Configuration Register, Address offset: 0x118 */ - uint32_t RESERVED6[7]; /*!< Reserved, 0x11C - 0x137 */ - __IO uint32_t VMCCR; /*!< DSI Host Video Mode Current Configuration Register, Address offset: 0x138 */ - __IO uint32_t VPCCR; /*!< DSI Host Video Packet Current Configuration Register, Address offset: 0x13C */ - __IO uint32_t VCCCR; /*!< DSI Host Video Chuncks Current Configuration Register, Address offset: 0x140 */ - __IO uint32_t VNPCCR; /*!< DSI Host Video Null Packet Current Configuration Register, Address offset: 0x144 */ - __IO uint32_t VHSACCR; /*!< DSI Host Video HSA Current Configuration Register, Address offset: 0x148 */ - __IO uint32_t VHBPCCR; /*!< DSI Host Video HBP Current Configuration Register, Address offset: 0x14C */ - __IO uint32_t VLCCR; /*!< DSI Host Video Line Current Configuration Register, Address offset: 0x150 */ - __IO uint32_t VVSACCR; /*!< DSI Host Video VSA Current Configuration Register, Address offset: 0x154 */ - __IO uint32_t VVBPCCR; /*!< DSI Host Video VBP Current Configuration Register, Address offset: 0x158 */ - __IO uint32_t VVFPCCR; /*!< DSI Host Video VFP Current Configuration Register, Address offset: 0x15C */ - __IO uint32_t VVACCR; /*!< DSI Host Video VA Current Configuration Register, Address offset: 0x160 */ - uint32_t RESERVED7[11]; /*!< Reserved, 0x164 - 0x18F */ - __IO uint32_t TDCCR; /*!< DSI Host 3D Current Configuration Register, Address offset: 0x190 */ - uint32_t RESERVED8[155]; /*!< Reserved, 0x194 - 0x3FF */ - __IO uint32_t WCFGR; /*!< DSI Wrapper Configuration Register, Address offset: 0x400 */ - __IO uint32_t WCR; /*!< DSI Wrapper Control Register, Address offset: 0x404 */ - __IO uint32_t WIER; /*!< DSI Wrapper Interrupt Enable Register, Address offset: 0x408 */ - __IO uint32_t WISR; /*!< DSI Wrapper Interrupt and Status Register, Address offset: 0x40C */ - __IO uint32_t WIFCR; /*!< DSI Wrapper Interrupt Flag Clear Register, Address offset: 0x410 */ - uint32_t RESERVED9; /*!< Reserved, 0x414 */ - __IO uint32_t WPCR[5]; /*!< DSI Wrapper PHY Configuration Register, Address offset: 0x418-0x42B */ - uint32_t RESERVED10; /*!< Reserved, 0x42C */ - __IO uint32_t WRPCR; /*!< DSI Wrapper Regulator and PLL Control Register, Address offset: 0x430 */ -} DSI_TypeDef; - -/** - * @brief Ethernet MAC - */ - -typedef struct -{ - __IO uint32_t MACCR; - __IO uint32_t MACFFR; - __IO uint32_t MACHTHR; - __IO uint32_t MACHTLR; - __IO uint32_t MACMIIAR; - __IO uint32_t MACMIIDR; - __IO uint32_t MACFCR; - __IO uint32_t MACVLANTR; /* 8 */ - uint32_t RESERVED0[2]; - __IO uint32_t MACRWUFFR; /* 11 */ - __IO uint32_t MACPMTCSR; - uint32_t RESERVED1[2]; - __IO uint32_t MACSR; /* 15 */ - __IO uint32_t MACIMR; - __IO uint32_t MACA0HR; - __IO uint32_t MACA0LR; - __IO uint32_t MACA1HR; - __IO uint32_t MACA1LR; - __IO uint32_t MACA2HR; - __IO uint32_t MACA2LR; - __IO uint32_t MACA3HR; - __IO uint32_t MACA3LR; /* 24 */ - uint32_t RESERVED2[40]; - __IO uint32_t MMCCR; /* 65 */ - __IO uint32_t MMCRIR; - __IO uint32_t MMCTIR; - __IO uint32_t MMCRIMR; - __IO uint32_t MMCTIMR; /* 69 */ - uint32_t RESERVED3[14]; - __IO uint32_t MMCTGFSCCR; /* 84 */ - __IO uint32_t MMCTGFMSCCR; - uint32_t RESERVED4[5]; - __IO uint32_t MMCTGFCR; - uint32_t RESERVED5[10]; - __IO uint32_t MMCRFCECR; - __IO uint32_t MMCRFAECR; - uint32_t RESERVED6[10]; - __IO uint32_t MMCRGUFCR; - uint32_t RESERVED7[334]; - __IO uint32_t PTPTSCR; - __IO uint32_t PTPSSIR; - __IO uint32_t PTPTSHR; - __IO uint32_t PTPTSLR; - __IO uint32_t PTPTSHUR; - __IO uint32_t PTPTSLUR; - __IO uint32_t PTPTSAR; - __IO uint32_t PTPTTHR; - __IO uint32_t PTPTTLR; - __IO uint32_t RESERVED8; - __IO uint32_t PTPTSSR; - uint32_t RESERVED9[565]; - __IO uint32_t DMABMR; - __IO uint32_t DMATPDR; - __IO uint32_t DMARPDR; - __IO uint32_t DMARDLAR; - __IO uint32_t DMATDLAR; - __IO uint32_t DMASR; - __IO uint32_t DMAOMR; - __IO uint32_t DMAIER; - __IO uint32_t DMAMFBOCR; - __IO uint32_t DMARSWTR; - uint32_t RESERVED10[8]; - __IO uint32_t DMACHTDR; - __IO uint32_t DMACHRDR; - __IO uint32_t DMACHTBAR; - __IO uint32_t DMACHRBAR; -} ETH_TypeDef; - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief Flexible Memory Controller - */ - -typedef struct -{ - __IO uint32_t BTCR[8]; /*!< NOR/PSRAM chip-select control register(BCR) and chip-select timing register(BTR), Address offset: 0x00-1C */ -} FMC_Bank1_TypeDef; - -/** - * @brief Flexible Memory Controller Bank1E - */ - -typedef struct -{ - __IO uint32_t BWTR[7]; /*!< NOR/PSRAM write timing registers, Address offset: 0x104-0x11C */ -} FMC_Bank1E_TypeDef; - -/** - * @brief Flexible Memory Controller Bank3 - */ - -typedef struct -{ - __IO uint32_t PCR; /*!< NAND Flash control register, Address offset: 0x80 */ - __IO uint32_t SR; /*!< NAND Flash FIFO status and interrupt register, Address offset: 0x84 */ - __IO uint32_t PMEM; /*!< NAND Flash Common memory space timing register, Address offset: 0x88 */ - __IO uint32_t PATT; /*!< NAND Flash Attribute memory space timing register, Address offset: 0x8C */ - uint32_t RESERVED; /*!< Reserved, 0x90 */ - __IO uint32_t ECCR; /*!< NAND Flash ECC result registers, Address offset: 0x94 */ -} FMC_Bank3_TypeDef; - -/** - * @brief Flexible Memory Controller Bank5_6 - */ - -typedef struct -{ - __IO uint32_t SDCR[2]; /*!< SDRAM Control registers , Address offset: 0x140-0x144 */ - __IO uint32_t SDTR[2]; /*!< SDRAM Timing registers , Address offset: 0x148-0x14C */ - __IO uint32_t SDCMR; /*!< SDRAM Command Mode register, Address offset: 0x150 */ - __IO uint32_t SDRTR; /*!< SDRAM Refresh Timer register, Address offset: 0x154 */ - __IO uint32_t SDSR; /*!< SDRAM Status register, Address offset: 0x158 */ -} FMC_Bank5_6_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief LCD-TFT Display Controller - */ - -typedef struct -{ - uint32_t RESERVED0[2]; /*!< Reserved, 0x00-0x04 */ - __IO uint32_t SSCR; /*!< LTDC Synchronization Size Configuration Register, Address offset: 0x08 */ - __IO uint32_t BPCR; /*!< LTDC Back Porch Configuration Register, Address offset: 0x0C */ - __IO uint32_t AWCR; /*!< LTDC Active Width Configuration Register, Address offset: 0x10 */ - __IO uint32_t TWCR; /*!< LTDC Total Width Configuration Register, Address offset: 0x14 */ - __IO uint32_t GCR; /*!< LTDC Global Control Register, Address offset: 0x18 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x1C-0x20 */ - __IO uint32_t SRCR; /*!< LTDC Shadow Reload Configuration Register, Address offset: 0x24 */ - uint32_t RESERVED2[1]; /*!< Reserved, 0x28 */ - __IO uint32_t BCCR; /*!< LTDC Background Color Configuration Register, Address offset: 0x2C */ - uint32_t RESERVED3[1]; /*!< Reserved, 0x30 */ - __IO uint32_t IER; /*!< LTDC Interrupt Enable Register, Address offset: 0x34 */ - __IO uint32_t ISR; /*!< LTDC Interrupt Status Register, Address offset: 0x38 */ - __IO uint32_t ICR; /*!< LTDC Interrupt Clear Register, Address offset: 0x3C */ - __IO uint32_t LIPCR; /*!< LTDC Line Interrupt Position Configuration Register, Address offset: 0x40 */ - __IO uint32_t CPSR; /*!< LTDC Current Position Status Register, Address offset: 0x44 */ - __IO uint32_t CDSR; /*!< LTDC Current Display Status Register, Address offset: 0x48 */ -} LTDC_TypeDef; - -/** - * @brief LCD-TFT Display layer x Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< LTDC Layerx Control Register Address offset: 0x84 */ - __IO uint32_t WHPCR; /*!< LTDC Layerx Window Horizontal Position Configuration Register Address offset: 0x88 */ - __IO uint32_t WVPCR; /*!< LTDC Layerx Window Vertical Position Configuration Register Address offset: 0x8C */ - __IO uint32_t CKCR; /*!< LTDC Layerx Color Keying Configuration Register Address offset: 0x90 */ - __IO uint32_t PFCR; /*!< LTDC Layerx Pixel Format Configuration Register Address offset: 0x94 */ - __IO uint32_t CACR; /*!< LTDC Layerx Constant Alpha Configuration Register Address offset: 0x98 */ - __IO uint32_t DCCR; /*!< LTDC Layerx Default Color Configuration Register Address offset: 0x9C */ - __IO uint32_t BFCR; /*!< LTDC Layerx Blending Factors Configuration Register Address offset: 0xA0 */ - uint32_t RESERVED0[2]; /*!< Reserved */ - __IO uint32_t CFBAR; /*!< LTDC Layerx Color Frame Buffer Address Register Address offset: 0xAC */ - __IO uint32_t CFBLR; /*!< LTDC Layerx Color Frame Buffer Length Register Address offset: 0xB0 */ - __IO uint32_t CFBLNR; /*!< LTDC Layerx ColorFrame Buffer Line Number Register Address offset: 0xB4 */ - uint32_t RESERVED1[3]; /*!< Reserved */ - __IO uint32_t CLUTWR; /*!< LTDC Layerx CLUT Write Register Address offset: 0x144 */ - -} LTDC_Layer_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - __IO uint32_t PLLSAICFGR; /*!< RCC PLLSAI configuration register, Address offset: 0x88 */ - __IO uint32_t DCKCFGR; /*!< RCC Dedicated Clocks configuration register, Address offset: 0x8C */ - -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - -/** - * @brief Serial Audio Interface - */ - -typedef struct -{ - __IO uint32_t GCR; /*!< SAI global configuration register, Address offset: 0x00 */ -} SAI_TypeDef; - -typedef struct -{ - __IO uint32_t CR1; /*!< SAI block x configuration register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< SAI block x configuration register 2, Address offset: 0x08 */ - __IO uint32_t FRCR; /*!< SAI block x frame configuration register, Address offset: 0x0C */ - __IO uint32_t SLOTR; /*!< SAI block x slot register, Address offset: 0x10 */ - __IO uint32_t IMR; /*!< SAI block x interrupt mask register, Address offset: 0x14 */ - __IO uint32_t SR; /*!< SAI block x status register, Address offset: 0x18 */ - __IO uint32_t CLRFR; /*!< SAI block x clear flag register, Address offset: 0x1C */ - __IO uint32_t DR; /*!< SAI block x data register, Address offset: 0x20 */ -} SAI_Block_TypeDef; - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief QUAD Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR; /*!< QUADSPI Control register, Address offset: 0x00 */ - __IO uint32_t DCR; /*!< QUADSPI Device Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< QUADSPI Status register, Address offset: 0x08 */ - __IO uint32_t FCR; /*!< QUADSPI Flag Clear register, Address offset: 0x0C */ - __IO uint32_t DLR; /*!< QUADSPI Data Length register, Address offset: 0x10 */ - __IO uint32_t CCR; /*!< QUADSPI Communication Configuration register, Address offset: 0x14 */ - __IO uint32_t AR; /*!< QUADSPI Address register, Address offset: 0x18 */ - __IO uint32_t ABR; /*!< QUADSPI Alternate Bytes register, Address offset: 0x1C */ - __IO uint32_t DR; /*!< QUADSPI Data register, Address offset: 0x20 */ - __IO uint32_t PSMKR; /*!< QUADSPI Polling Status Mask register, Address offset: 0x24 */ - __IO uint32_t PSMAR; /*!< QUADSPI Polling Status Match register, Address offset: 0x28 */ - __IO uint32_t PIR; /*!< QUADSPI Polling Interval register, Address offset: 0x2C */ - __IO uint32_t LPTR; /*!< QUADSPI Low Power Timeout register, Address offset: 0x30 */ -} QUADSPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - -/** - * @brief USB_OTG_Core_Registers - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register 000h */ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register 004h */ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register 008h */ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register 00Ch */ - __IO uint32_t GRSTCTL; /*!< Core Reset Register 010h */ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register 014h */ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register 018h */ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register 01Ch */ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register 020h */ - __IO uint32_t GRXFSIZ; /*!< Receive FIFO Size Register 024h */ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register 028h */ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg 02Ch */ - uint32_t Reserved30[2]; /*!< Reserved 030h */ - __IO uint32_t GCCFG; /*!< General Purpose IO Register 038h */ - __IO uint32_t CID; /*!< User ID Register 03Ch */ - uint32_t Reserved5[3]; /*!< Reserved 040h-048h */ - __IO uint32_t GHWCFG3; /*!< User HW config3 04Ch */ - uint32_t Reserved6; /*!< Reserved 050h */ - __IO uint32_t GLPMCFG; /*!< LPM Register 054h */ - uint32_t Reserved; /*!< Reserved 058h */ - __IO uint32_t GDFIFOCFG; /*!< DFIFO Software Config Register 05Ch */ - uint32_t Reserved43[40]; /*!< Reserved 058h-0FFh */ - __IO uint32_t HPTXFSIZ; /*!< Host Periodic Tx FIFO Size Reg 100h */ - __IO uint32_t DIEPTXF[0x0F]; /*!< dev Periodic Transmit FIFO */ -} USB_OTG_GlobalTypeDef; - -/** - * @brief USB_OTG_device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /*!< dev Configuration Register 800h */ - __IO uint32_t DCTL; /*!< dev Control Register 804h */ - __IO uint32_t DSTS; /*!< dev Status Register (RO) 808h */ - uint32_t Reserved0C; /*!< Reserved 80Ch */ - __IO uint32_t DIEPMSK; /*!< dev IN Endpoint Mask 810h */ - __IO uint32_t DOEPMSK; /*!< dev OUT Endpoint Mask 814h */ - __IO uint32_t DAINT; /*!< dev All Endpoints Itr Reg 818h */ - __IO uint32_t DAINTMSK; /*!< dev All Endpoints Itr Mask 81Ch */ - uint32_t Reserved20; /*!< Reserved 820h */ - uint32_t Reserved9; /*!< Reserved 824h */ - __IO uint32_t DVBUSDIS; /*!< dev VBUS discharge Register 828h */ - __IO uint32_t DVBUSPULSE; /*!< dev VBUS Pulse Register 82Ch */ - __IO uint32_t DTHRCTL; /*!< dev threshold 830h */ - __IO uint32_t DIEPEMPMSK; /*!< dev empty msk 834h */ - __IO uint32_t DEACHINT; /*!< dedicated EP interrupt 838h */ - __IO uint32_t DEACHMSK; /*!< dedicated EP msk 83Ch */ - uint32_t Reserved40; /*!< dedicated EP mask 840h */ - __IO uint32_t DINEP1MSK; /*!< dedicated EP mask 844h */ - uint32_t Reserved44[15]; /*!< Reserved 844-87Ch */ - __IO uint32_t DOUTEP1MSK; /*!< dedicated EP msk 884h */ -} USB_OTG_DeviceTypeDef; - -/** - * @brief USB_OTG_IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /*!< dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /*!< Reserved 900h + (ep_num * 20h) + 04h */ - __IO uint32_t DIEPINT; /*!< dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /*!< Reserved 900h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DIEPTSIZ; /*!< IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h */ - __IO uint32_t DIEPDMA; /*!< IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h */ - __IO uint32_t DTXFSTS; /*!< IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h */ - uint32_t Reserved18; /*!< Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch */ -} USB_OTG_INEndpointTypeDef; - -/** - * @brief USB_OTG_OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /*!< dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /*!< Reserved B00h + (ep_num * 20h) + 04h */ - __IO uint32_t DOEPINT; /*!< dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /*!< Reserved B00h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DOEPTSIZ; /*!< dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h */ - __IO uint32_t DOEPDMA; /*!< dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h */ - uint32_t Reserved18[2]; /*!< Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch */ -} USB_OTG_OUTEndpointTypeDef; - -/** - * @brief USB_OTG_Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /*!< Host Configuration Register 400h */ - __IO uint32_t HFIR; /*!< Host Frame Interval Register 404h */ - __IO uint32_t HFNUM; /*!< Host Frame Nbr/Frame Remaining 408h */ - uint32_t Reserved40C; /*!< Reserved 40Ch */ - __IO uint32_t HPTXSTS; /*!< Host Periodic Tx FIFO/ Queue Status 410h */ - __IO uint32_t HAINT; /*!< Host All Channels Interrupt Register 414h */ - __IO uint32_t HAINTMSK; /*!< Host All Channels Interrupt Mask 418h */ -} USB_OTG_HostTypeDef; - -/** - * @brief USB_OTG_Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; /*!< Host Channel Characteristics Register 500h */ - __IO uint32_t HCSPLT; /*!< Host Channel Split Control Register 504h */ - __IO uint32_t HCINT; /*!< Host Channel Interrupt Register 508h */ - __IO uint32_t HCINTMSK; /*!< Host Channel Interrupt Mask Register 50Ch */ - __IO uint32_t HCTSIZ; /*!< Host Channel Transfer Size Register 510h */ - __IO uint32_t HCDMA; /*!< Host Channel DMA Address Register 514h */ - uint32_t Reserved[2]; /*!< Reserved */ -} USB_OTG_HostChannelTypeDef; - -/** - * @} - */ - -/** @addtogroup Peripheral_memory_map - * @{ - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define CCMDATARAM_BASE 0x10000000U /*!< CCM(core coupled memory) data RAM(64 KB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(160 KB) base address in the alias region */ -#define SRAM2_BASE 0x20028000U /*!< SRAM2(32 KB) base address in the alias region */ -#define SRAM3_BASE 0x20030000U /*!< SRAM3(128 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define BKPSRAM_BASE 0x40024000U /*!< Backup SRAM(4 KB) base address in the alias region */ -#define FMC_R_BASE 0xA0000000U /*!< FMC registers base address */ -#define QSPI_R_BASE 0xA0001000U /*!< QuadSPI registers base address */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(112 KB) base address in the bit-band region */ -#define SRAM2_BB_BASE 0x22500000U /*!< SRAM2(16 KB) base address in the bit-band region */ -#define SRAM3_BB_BASE 0x22600000U /*!< SRAM3(64 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define BKPSRAM_BB_BASE 0x42480000U /*!< Backup SRAM(4 KB) base address in the bit-band region */ -#define FLASH_END 0x081FFFFFU /*!< FLASH end address */ -#define CCMDATARAM_END 0x1000FFFFU /*!< CCM data RAM end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define TIM7_BASE (APB1PERIPH_BASE + 0x1400U) -#define TIM12_BASE (APB1PERIPH_BASE + 0x1800U) -#define TIM13_BASE (APB1PERIPH_BASE + 0x1C00U) -#define TIM14_BASE (APB1PERIPH_BASE + 0x2000U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define USART3_BASE (APB1PERIPH_BASE + 0x4800U) -#define UART4_BASE (APB1PERIPH_BASE + 0x4C00U) -#define UART5_BASE (APB1PERIPH_BASE + 0x5000U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define CAN1_BASE (APB1PERIPH_BASE + 0x6400U) -#define CAN2_BASE (APB1PERIPH_BASE + 0x6800U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) -#define DAC_BASE (APB1PERIPH_BASE + 0x7400U) -#define UART7_BASE (APB1PERIPH_BASE + 0x7800U) -#define UART8_BASE (APB1PERIPH_BASE + 0x7C00U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define TIM8_BASE (APB2PERIPH_BASE + 0x0400U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC2_BASE (APB2PERIPH_BASE + 0x2100U) -#define ADC3_BASE (APB2PERIPH_BASE + 0x2200U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SPI4_BASE (APB2PERIPH_BASE + 0x3400U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) -#define SPI5_BASE (APB2PERIPH_BASE + 0x5000U) -#define SPI6_BASE (APB2PERIPH_BASE + 0x5400U) -#define SAI1_BASE (APB2PERIPH_BASE + 0x5800U) -#define SAI1_Block_A_BASE (SAI1_BASE + 0x004U) -#define SAI1_Block_B_BASE (SAI1_BASE + 0x024U) -#define LTDC_BASE (APB2PERIPH_BASE + 0x6800U) -#define LTDC_Layer1_BASE (LTDC_BASE + 0x84U) -#define LTDC_Layer2_BASE (LTDC_BASE + 0x104U) -#define DSI_BASE (APB2PERIPH_BASE + 0x6C00U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOF_BASE (AHB1PERIPH_BASE + 0x1400U) -#define GPIOG_BASE (AHB1PERIPH_BASE + 0x1800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define GPIOI_BASE (AHB1PERIPH_BASE + 0x2000U) -#define GPIOJ_BASE (AHB1PERIPH_BASE + 0x2400U) -#define GPIOK_BASE (AHB1PERIPH_BASE + 0x2800U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) -#define ETH_BASE (AHB1PERIPH_BASE + 0x8000U) -#define ETH_MAC_BASE (ETH_BASE) -#define ETH_MMC_BASE (ETH_BASE + 0x0100U) -#define ETH_PTP_BASE (ETH_BASE + 0x0700U) -#define ETH_DMA_BASE (ETH_BASE + 0x1000U) -#define DMA2D_BASE (AHB1PERIPH_BASE + 0xB000U) - -/*!< AHB2 peripherals */ -#define DCMI_BASE (AHB2PERIPH_BASE + 0x50000U) -#define RNG_BASE (AHB2PERIPH_BASE + 0x60800U) - -/*!< FMC Bankx registers base address */ -#define FMC_Bank1_R_BASE (FMC_R_BASE + 0x0000U) -#define FMC_Bank1E_R_BASE (FMC_R_BASE + 0x0104U) -#define FMC_Bank3_R_BASE (FMC_R_BASE + 0x0080U) -#define FMC_Bank5_6_R_BASE (FMC_R_BASE + 0x0140U) - -/*!< Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_HS_PERIPH_BASE 0x40040000U -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define TIM7 ((TIM_TypeDef *) TIM7_BASE) -#define TIM12 ((TIM_TypeDef *) TIM12_BASE) -#define TIM13 ((TIM_TypeDef *) TIM13_BASE) -#define TIM14 ((TIM_TypeDef *) TIM14_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define USART3 ((USART_TypeDef *) USART3_BASE) -#define UART4 ((USART_TypeDef *) UART4_BASE) -#define UART5 ((USART_TypeDef *) UART5_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define CAN1 ((CAN_TypeDef *) CAN1_BASE) -#define CAN2 ((CAN_TypeDef *) CAN2_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define DAC ((DAC_TypeDef *) DAC_BASE) -#define UART7 ((USART_TypeDef *) UART7_BASE) -#define UART8 ((USART_TypeDef *) UART8_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define TIM8 ((TIM_TypeDef *) TIM8_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define ADC2 ((ADC_TypeDef *) ADC2_BASE) -#define ADC3 ((ADC_TypeDef *) ADC3_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SPI4 ((SPI_TypeDef *) SPI4_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define SPI5 ((SPI_TypeDef *) SPI5_BASE) -#define SPI6 ((SPI_TypeDef *) SPI6_BASE) -#define SAI1 ((SAI_TypeDef *) SAI1_BASE) -#define SAI1_Block_A ((SAI_Block_TypeDef *)SAI1_Block_A_BASE) -#define SAI1_Block_B ((SAI_Block_TypeDef *)SAI1_Block_B_BASE) -#define LTDC ((LTDC_TypeDef *)LTDC_BASE) -#define LTDC_Layer1 ((LTDC_Layer_TypeDef *)LTDC_Layer1_BASE) -#define LTDC_Layer2 ((LTDC_Layer_TypeDef *)LTDC_Layer2_BASE) -#define DSI ((DSI_TypeDef *)DSI_BASE) - -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOF ((GPIO_TypeDef *) GPIOF_BASE) -#define GPIOG ((GPIO_TypeDef *) GPIOG_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define GPIOI ((GPIO_TypeDef *) GPIOI_BASE) -#define GPIOJ ((GPIO_TypeDef *) GPIOJ_BASE) -#define GPIOK ((GPIO_TypeDef *) GPIOK_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define ETH ((ETH_TypeDef *) ETH_BASE) -#define DMA2D ((DMA2D_TypeDef *)DMA2D_BASE) -#define DCMI ((DCMI_TypeDef *) DCMI_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) -#define FMC_Bank1 ((FMC_Bank1_TypeDef *) FMC_Bank1_R_BASE) -#define FMC_Bank1E ((FMC_Bank1E_TypeDef *) FMC_Bank1E_R_BASE) -#define FMC_Bank3 ((FMC_Bank3_TypeDef *) FMC_Bank3_R_BASE) -#define FMC_Bank5_6 ((FMC_Bank5_6_TypeDef *) FMC_Bank5_6_R_BASE) -#define QUADSPI ((QUADSPI_TypeDef *) QSPI_R_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) -#define USB_OTG_HS ((USB_OTG_GlobalTypeDef *) USB_OTG_HS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS_Device - * @{ - */ - -/** @addtogroup stm32f479xx - * @{ - */ - -#ifndef __STM32F479xx_H -#define __STM32F479xx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - -/** @addtogroup Configuration_section_for_CMSIS - * @{ - */ - -/** - * @brief Configuration of the Cortex-M4 Processor and Core Peripherals - */ -#define __CM4_REV 0x0001U /*!< Core revision r0p1 */ -#define __MPU_PRESENT 1U /*!< STM32F4XX provides an MPU */ -#define __NVIC_PRIO_BITS 4U /*!< STM32F4XX uses 4 Bits for the Priority Levels */ -#define __Vendor_SysTickConfig 0U /*!< Set to 1 if different SysTick Config is used */ -#define __FPU_PRESENT 1U /*!< FPU present */ - -/** - * @} - */ - -/** @addtogroup Peripheral_interrupt_number_definition - * @{ - */ - -/** - * @brief STM32F4XX Interrupt Number Definition, according to the selected device - * in @ref Library_configuration_section - */ -typedef enum -{ - /****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ - NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ - MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ - BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ - UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ - SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ - DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ - PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ - SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ - /****** STM32 specific Interrupt Numbers **********************************************************************/ - WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ - PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ - TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */ - RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */ - FLASH_IRQn = 4, /*!< FLASH global Interrupt */ - RCC_IRQn = 5, /*!< RCC global Interrupt */ - EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ - EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ - EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */ - EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ - EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ - DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */ - DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */ - DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */ - DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */ - DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */ - DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */ - DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */ - ADC_IRQn = 18, /*!< ADC1, ADC2 and ADC3 global Interrupts */ - CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */ - CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */ - CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ - CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ - EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ - TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */ - TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */ - TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */ - TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ - TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ - TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ - TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ - I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ - I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ - I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ - I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ - SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ - SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ - USART1_IRQn = 37, /*!< USART1 global Interrupt */ - USART2_IRQn = 38, /*!< USART2 global Interrupt */ - USART3_IRQn = 39, /*!< USART3 global Interrupt */ - EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ - RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ - OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */ - TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */ - TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */ - TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */ - TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare global interrupt */ - DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */ - FMC_IRQn = 48, /*!< FMC global Interrupt */ - SDIO_IRQn = 49, /*!< SDIO global Interrupt */ - TIM5_IRQn = 50, /*!< TIM5 global Interrupt */ - SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ - UART4_IRQn = 52, /*!< UART4 global Interrupt */ - UART5_IRQn = 53, /*!< UART5 global Interrupt */ - TIM6_DAC_IRQn = 54, /*!< TIM6 global and DAC1&2 underrun error interrupts */ - TIM7_IRQn = 55, /*!< TIM7 global interrupt */ - DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */ - DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */ - DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */ - DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */ - DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */ - ETH_IRQn = 61, /*!< Ethernet global Interrupt */ - ETH_WKUP_IRQn = 62, /*!< Ethernet Wakeup through EXTI line Interrupt */ - CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */ - CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */ - CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */ - CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */ - OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */ - DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */ - DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */ - DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */ - USART6_IRQn = 71, /*!< USART6 global interrupt */ - I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */ - I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */ - OTG_HS_EP1_OUT_IRQn = 74, /*!< USB OTG HS End Point 1 Out global interrupt */ - OTG_HS_EP1_IN_IRQn = 75, /*!< USB OTG HS End Point 1 In global interrupt */ - OTG_HS_WKUP_IRQn = 76, /*!< USB OTG HS Wakeup through EXTI interrupt */ - OTG_HS_IRQn = 77, /*!< USB OTG HS global interrupt */ - DCMI_IRQn = 78, /*!< DCMI global interrupt */ - CRYP_IRQn = 79, /*!< CRYP crypto global interrupt */ - HASH_RNG_IRQn = 80, /*!< Hash and Rng global interrupt */ - FPU_IRQn = 81, /*!< FPU global interrupt */ - UART7_IRQn = 82, /*!< UART7 global interrupt */ - UART8_IRQn = 83, /*!< UART8 global interrupt */ - SPI4_IRQn = 84, /*!< SPI4 global Interrupt */ - SPI5_IRQn = 85, /*!< SPI5 global Interrupt */ - SPI6_IRQn = 86, /*!< SPI6 global Interrupt */ - SAI1_IRQn = 87, /*!< SAI1 global Interrupt */ - LTDC_IRQn = 88, /*!< LTDC global Interrupt */ - LTDC_ER_IRQn = 89, /*!< LTDC Error global Interrupt */ - DMA2D_IRQn = 90, /*!< DMA2D global Interrupt */ - QUADSPI_IRQn = 91, /*!< QUADSPI global Interrupt */ - DSI_IRQn = 92 /*!< DSI global Interrupt */ -} IRQn_Type; - -/** - * @} - */ - -#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ -#include "system_stm32f4xx.h" -#include - -/** @addtogroup Peripheral_registers_structures - * @{ - */ - -/** - * @brief Analog to Digital Converter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< ADC status register, Address offset: 0x00 */ - __IO uint32_t CR1; /*!< ADC control register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< ADC control register 2, Address offset: 0x08 */ - __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x0C */ - __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x10 */ - __IO uint32_t JOFR1; /*!< ADC injected channel data offset register 1, Address offset: 0x14 */ - __IO uint32_t JOFR2; /*!< ADC injected channel data offset register 2, Address offset: 0x18 */ - __IO uint32_t JOFR3; /*!< ADC injected channel data offset register 3, Address offset: 0x1C */ - __IO uint32_t JOFR4; /*!< ADC injected channel data offset register 4, Address offset: 0x20 */ - __IO uint32_t HTR; /*!< ADC watchdog higher threshold register, Address offset: 0x24 */ - __IO uint32_t LTR; /*!< ADC watchdog lower threshold register, Address offset: 0x28 */ - __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x2C */ - __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x30 */ - __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x34 */ - __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x38*/ - __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x3C */ - __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x40 */ - __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x44 */ - __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x48 */ - __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x4C */ -} ADC_TypeDef; - -typedef struct -{ - __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1 base address + 0x300 */ - __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1 base address + 0x304 */ - __IO uint32_t CDR; /*!< ADC common regular data register for dual - AND triple modes, Address offset: ADC1 base address + 0x308 */ -} ADC_Common_TypeDef; - - -/** - * @brief Controller Area Network TxMailBox - */ - -typedef struct -{ - __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ - __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ - __IO uint32_t TDLR; /*!< CAN mailbox data low register */ - __IO uint32_t TDHR; /*!< CAN mailbox data high register */ -} CAN_TxMailBox_TypeDef; - -/** - * @brief Controller Area Network FIFOMailBox - */ - -typedef struct -{ - __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ - __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ - __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ - __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ -} CAN_FIFOMailBox_TypeDef; - -/** - * @brief Controller Area Network FilterRegister - */ - -typedef struct -{ - __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ - __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ -} CAN_FilterRegister_TypeDef; - -/** - * @brief Controller Area Network - */ - -typedef struct -{ - __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ - __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ - __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ - __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ - __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ - __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ - __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ - __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ - uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ - CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ - CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ - uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ - __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ - __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ - uint32_t RESERVED2; /*!< Reserved, 0x208 */ - __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ - uint32_t RESERVED3; /*!< Reserved, 0x210 */ - __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ - uint32_t RESERVED4; /*!< Reserved, 0x218 */ - __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ - uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ - CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ -} CAN_TypeDef; - -/** - * @brief CRC calculation unit - */ - -typedef struct -{ - __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ - __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ - uint8_t RESERVED0; /*!< Reserved, 0x05 */ - uint16_t RESERVED1; /*!< Reserved, 0x06 */ - __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ -} CRC_TypeDef; - -/** - * @brief Digital to Analog Converter - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ - __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ - __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ - __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ - __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ - __IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */ - __IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */ - __IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */ - __IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */ - __IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */ - __IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */ - __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ - __IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */ - __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ -} DAC_TypeDef; - -/** - * @brief Debug MCU - */ - -typedef struct -{ - __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ - __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ - __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ - __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ -} DBGMCU_TypeDef; - -/** - * @brief DCMI - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DCMI control register 1, Address offset: 0x00 */ - __IO uint32_t SR; /*!< DCMI status register, Address offset: 0x04 */ - __IO uint32_t RISR; /*!< DCMI raw interrupt status register, Address offset: 0x08 */ - __IO uint32_t IER; /*!< DCMI interrupt enable register, Address offset: 0x0C */ - __IO uint32_t MISR; /*!< DCMI masked interrupt status register, Address offset: 0x10 */ - __IO uint32_t ICR; /*!< DCMI interrupt clear register, Address offset: 0x14 */ - __IO uint32_t ESCR; /*!< DCMI embedded synchronization code register, Address offset: 0x18 */ - __IO uint32_t ESUR; /*!< DCMI embedded synchronization unmask register, Address offset: 0x1C */ - __IO uint32_t CWSTRTR; /*!< DCMI crop window start, Address offset: 0x20 */ - __IO uint32_t CWSIZER; /*!< DCMI crop window size, Address offset: 0x24 */ - __IO uint32_t DR; /*!< DCMI data register, Address offset: 0x28 */ -} DCMI_TypeDef; - -/** - * @brief DMA Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA stream x configuration register */ - __IO uint32_t NDTR; /*!< DMA stream x number of data register */ - __IO uint32_t PAR; /*!< DMA stream x peripheral address register */ - __IO uint32_t M0AR; /*!< DMA stream x memory 0 address register */ - __IO uint32_t M1AR; /*!< DMA stream x memory 1 address register */ - __IO uint32_t FCR; /*!< DMA stream x FIFO control register */ -} DMA_Stream_TypeDef; - -typedef struct -{ - __IO uint32_t LISR; /*!< DMA low interrupt status register, Address offset: 0x00 */ - __IO uint32_t HISR; /*!< DMA high interrupt status register, Address offset: 0x04 */ - __IO uint32_t LIFCR; /*!< DMA low interrupt flag clear register, Address offset: 0x08 */ - __IO uint32_t HIFCR; /*!< DMA high interrupt flag clear register, Address offset: 0x0C */ -} DMA_TypeDef; - -/** - * @brief DMA2D Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< DMA2D Control Register, Address offset: 0x00 */ - __IO uint32_t ISR; /*!< DMA2D Interrupt Status Register, Address offset: 0x04 */ - __IO uint32_t IFCR; /*!< DMA2D Interrupt Flag Clear Register, Address offset: 0x08 */ - __IO uint32_t FGMAR; /*!< DMA2D Foreground Memory Address Register, Address offset: 0x0C */ - __IO uint32_t FGOR; /*!< DMA2D Foreground Offset Register, Address offset: 0x10 */ - __IO uint32_t BGMAR; /*!< DMA2D Background Memory Address Register, Address offset: 0x14 */ - __IO uint32_t BGOR; /*!< DMA2D Background Offset Register, Address offset: 0x18 */ - __IO uint32_t FGPFCCR; /*!< DMA2D Foreground PFC Control Register, Address offset: 0x1C */ - __IO uint32_t FGCOLR; /*!< DMA2D Foreground Color Register, Address offset: 0x20 */ - __IO uint32_t BGPFCCR; /*!< DMA2D Background PFC Control Register, Address offset: 0x24 */ - __IO uint32_t BGCOLR; /*!< DMA2D Background Color Register, Address offset: 0x28 */ - __IO uint32_t FGCMAR; /*!< DMA2D Foreground CLUT Memory Address Register, Address offset: 0x2C */ - __IO uint32_t BGCMAR; /*!< DMA2D Background CLUT Memory Address Register, Address offset: 0x30 */ - __IO uint32_t OPFCCR; /*!< DMA2D Output PFC Control Register, Address offset: 0x34 */ - __IO uint32_t OCOLR; /*!< DMA2D Output Color Register, Address offset: 0x38 */ - __IO uint32_t OMAR; /*!< DMA2D Output Memory Address Register, Address offset: 0x3C */ - __IO uint32_t OOR; /*!< DMA2D Output Offset Register, Address offset: 0x40 */ - __IO uint32_t NLR; /*!< DMA2D Number of Line Register, Address offset: 0x44 */ - __IO uint32_t LWR; /*!< DMA2D Line Watermark Register, Address offset: 0x48 */ - __IO uint32_t AMTCR; /*!< DMA2D AHB Master Timer Configuration Register, Address offset: 0x4C */ - uint32_t RESERVED[236]; /*!< Reserved, 0x50-0x3FF */ - __IO uint32_t FGCLUT[256]; /*!< DMA2D Foreground CLUT, Address offset:400-7FF */ - __IO uint32_t BGCLUT[256]; /*!< DMA2D Background CLUT, Address offset:800-BFF */ -} DMA2D_TypeDef; - -/** - * @brief DSI Controller - */ - -typedef struct -{ - __IO uint32_t VR; /*!< DSI Host Version Register, Address offset: 0x00 */ - __IO uint32_t CR; /*!< DSI Host Control Register, Address offset: 0x04 */ - __IO uint32_t CCR; /*!< DSI HOST Clock Control Register, Address offset: 0x08 */ - __IO uint32_t LVCIDR; /*!< DSI Host LTDC VCID Register, Address offset: 0x0C */ - __IO uint32_t LCOLCR; /*!< DSI Host LTDC Color Coding Register, Address offset: 0x10 */ - __IO uint32_t LPCR; /*!< DSI Host LTDC Polarity Configuration Register, Address offset: 0x14 */ - __IO uint32_t LPMCR; /*!< DSI Host Low-Power Mode Configuration Register, Address offset: 0x18 */ - uint32_t RESERVED0[4]; /*!< Reserved, 0x1C - 0x2B */ - __IO uint32_t PCR; /*!< DSI Host Protocol Configuration Register, Address offset: 0x2C */ - __IO uint32_t GVCIDR; /*!< DSI Host Generic VCID Register, Address offset: 0x30 */ - __IO uint32_t MCR; /*!< DSI Host Mode Configuration Register, Address offset: 0x34 */ - __IO uint32_t VMCR; /*!< DSI Host Video Mode Configuration Register, Address offset: 0x38 */ - __IO uint32_t VPCR; /*!< DSI Host Video Packet Configuration Register, Address offset: 0x3C */ - __IO uint32_t VCCR; /*!< DSI Host Video Chunks Configuration Register, Address offset: 0x40 */ - __IO uint32_t VNPCR; /*!< DSI Host Video Null Packet Configuration Register, Address offset: 0x44 */ - __IO uint32_t VHSACR; /*!< DSI Host Video HSA Configuration Register, Address offset: 0x48 */ - __IO uint32_t VHBPCR; /*!< DSI Host Video HBP Configuration Register, Address offset: 0x4C */ - __IO uint32_t VLCR; /*!< DSI Host Video Line Configuration Register, Address offset: 0x50 */ - __IO uint32_t VVSACR; /*!< DSI Host Video VSA Configuration Register, Address offset: 0x54 */ - __IO uint32_t VVBPCR; /*!< DSI Host Video VBP Configuration Register, Address offset: 0x58 */ - __IO uint32_t VVFPCR; /*!< DSI Host Video VFP Configuration Register, Address offset: 0x5C */ - __IO uint32_t VVACR; /*!< DSI Host Video VA Configuration Register, Address offset: 0x60 */ - __IO uint32_t LCCR; /*!< DSI Host LTDC Command Configuration Register, Address offset: 0x64 */ - __IO uint32_t CMCR; /*!< DSI Host Command Mode Configuration Register, Address offset: 0x68 */ - __IO uint32_t GHCR; /*!< DSI Host Generic Header Configuration Register, Address offset: 0x6C */ - __IO uint32_t GPDR; /*!< DSI Host Generic Payload Data Register, Address offset: 0x70 */ - __IO uint32_t GPSR; /*!< DSI Host Generic Packet Status Register, Address offset: 0x74 */ - __IO uint32_t TCCR[6]; /*!< DSI Host Timeout Counter Configuration Register, Address offset: 0x78-0x8F */ - __IO uint32_t TDCR; /*!< DSI Host 3D Configuration Register, Address offset: 0x90 */ - __IO uint32_t CLCR; /*!< DSI Host Clock Lane Configuration Register, Address offset: 0x94 */ - __IO uint32_t CLTCR; /*!< DSI Host Clock Lane Timer Configuration Register, Address offset: 0x98 */ - __IO uint32_t DLTCR; /*!< DSI Host Data Lane Timer Configuration Register, Address offset: 0x9C */ - __IO uint32_t PCTLR; /*!< DSI Host PHY Control Register, Address offset: 0xA0 */ - __IO uint32_t PCONFR; /*!< DSI Host PHY Configuration Register, Address offset: 0xA4 */ - __IO uint32_t PUCR; /*!< DSI Host PHY ULPS Control Register, Address offset: 0xA8 */ - __IO uint32_t PTTCR; /*!< DSI Host PHY TX Triggers Configuration Register, Address offset: 0xAC */ - __IO uint32_t PSR; /*!< DSI Host PHY Status Register, Address offset: 0xB0 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0xB4 - 0xBB */ - __IO uint32_t ISR[2]; /*!< DSI Host Interrupt & Status Register, Address offset: 0xBC-0xC3 */ - __IO uint32_t IER[2]; /*!< DSI Host Interrupt Enable Register, Address offset: 0xC4-0xCB */ - uint32_t RESERVED2[3]; /*!< Reserved, 0xD0 - 0xD7 */ - __IO uint32_t FIR[2]; /*!< DSI Host Force Interrupt Register, Address offset: 0xD8-0xDF */ - uint32_t RESERVED3[8]; /*!< Reserved, 0xE0 - 0xFF */ - __IO uint32_t VSCR; /*!< DSI Host Video Shadow Control Register, Address offset: 0x100 */ - uint32_t RESERVED4[2]; /*!< Reserved, 0x104 - 0x10B */ - __IO uint32_t LCVCIDR; /*!< DSI Host LTDC Current VCID Register, Address offset: 0x10C */ - __IO uint32_t LCCCR; /*!< DSI Host LTDC Current Color Coding Register, Address offset: 0x110 */ - uint32_t RESERVED5; /*!< Reserved, 0x114 */ - __IO uint32_t LPMCCR; /*!< DSI Host Low-power Mode Current Configuration Register, Address offset: 0x118 */ - uint32_t RESERVED6[7]; /*!< Reserved, 0x11C - 0x137 */ - __IO uint32_t VMCCR; /*!< DSI Host Video Mode Current Configuration Register, Address offset: 0x138 */ - __IO uint32_t VPCCR; /*!< DSI Host Video Packet Current Configuration Register, Address offset: 0x13C */ - __IO uint32_t VCCCR; /*!< DSI Host Video Chuncks Current Configuration Register, Address offset: 0x140 */ - __IO uint32_t VNPCCR; /*!< DSI Host Video Null Packet Current Configuration Register, Address offset: 0x144 */ - __IO uint32_t VHSACCR; /*!< DSI Host Video HSA Current Configuration Register, Address offset: 0x148 */ - __IO uint32_t VHBPCCR; /*!< DSI Host Video HBP Current Configuration Register, Address offset: 0x14C */ - __IO uint32_t VLCCR; /*!< DSI Host Video Line Current Configuration Register, Address offset: 0x150 */ - __IO uint32_t VVSACCR; /*!< DSI Host Video VSA Current Configuration Register, Address offset: 0x154 */ - __IO uint32_t VVBPCCR; /*!< DSI Host Video VBP Current Configuration Register, Address offset: 0x158 */ - __IO uint32_t VVFPCCR; /*!< DSI Host Video VFP Current Configuration Register, Address offset: 0x15C */ - __IO uint32_t VVACCR; /*!< DSI Host Video VA Current Configuration Register, Address offset: 0x160 */ - uint32_t RESERVED7[11]; /*!< Reserved, 0x164 - 0x18F */ - __IO uint32_t TDCCR; /*!< DSI Host 3D Current Configuration Register, Address offset: 0x190 */ - uint32_t RESERVED8[155]; /*!< Reserved, 0x194 - 0x3FF */ - __IO uint32_t WCFGR; /*!< DSI Wrapper Configuration Register, Address offset: 0x400 */ - __IO uint32_t WCR; /*!< DSI Wrapper Control Register, Address offset: 0x404 */ - __IO uint32_t WIER; /*!< DSI Wrapper Interrupt Enable Register, Address offset: 0x408 */ - __IO uint32_t WISR; /*!< DSI Wrapper Interrupt and Status Register, Address offset: 0x40C */ - __IO uint32_t WIFCR; /*!< DSI Wrapper Interrupt Flag Clear Register, Address offset: 0x410 */ - uint32_t RESERVED9; /*!< Reserved, 0x414 */ - __IO uint32_t WPCR[5]; /*!< DSI Wrapper PHY Configuration Register, Address offset: 0x418-0x42B */ - uint32_t RESERVED10; /*!< Reserved, 0x42C */ - __IO uint32_t WRPCR; /*!< DSI Wrapper Regulator and PLL Control Register, Address offset: 0x430 */ -} DSI_TypeDef; - -/** - * @brief Ethernet MAC - */ - -typedef struct -{ - __IO uint32_t MACCR; - __IO uint32_t MACFFR; - __IO uint32_t MACHTHR; - __IO uint32_t MACHTLR; - __IO uint32_t MACMIIAR; - __IO uint32_t MACMIIDR; - __IO uint32_t MACFCR; - __IO uint32_t MACVLANTR; /* 8 */ - uint32_t RESERVED0[2]; - __IO uint32_t MACRWUFFR; /* 11 */ - __IO uint32_t MACPMTCSR; - uint32_t RESERVED1[2]; - __IO uint32_t MACSR; /* 15 */ - __IO uint32_t MACIMR; - __IO uint32_t MACA0HR; - __IO uint32_t MACA0LR; - __IO uint32_t MACA1HR; - __IO uint32_t MACA1LR; - __IO uint32_t MACA2HR; - __IO uint32_t MACA2LR; - __IO uint32_t MACA3HR; - __IO uint32_t MACA3LR; /* 24 */ - uint32_t RESERVED2[40]; - __IO uint32_t MMCCR; /* 65 */ - __IO uint32_t MMCRIR; - __IO uint32_t MMCTIR; - __IO uint32_t MMCRIMR; - __IO uint32_t MMCTIMR; /* 69 */ - uint32_t RESERVED3[14]; - __IO uint32_t MMCTGFSCCR; /* 84 */ - __IO uint32_t MMCTGFMSCCR; - uint32_t RESERVED4[5]; - __IO uint32_t MMCTGFCR; - uint32_t RESERVED5[10]; - __IO uint32_t MMCRFCECR; - __IO uint32_t MMCRFAECR; - uint32_t RESERVED6[10]; - __IO uint32_t MMCRGUFCR; - uint32_t RESERVED7[334]; - __IO uint32_t PTPTSCR; - __IO uint32_t PTPSSIR; - __IO uint32_t PTPTSHR; - __IO uint32_t PTPTSLR; - __IO uint32_t PTPTSHUR; - __IO uint32_t PTPTSLUR; - __IO uint32_t PTPTSAR; - __IO uint32_t PTPTTHR; - __IO uint32_t PTPTTLR; - __IO uint32_t RESERVED8; - __IO uint32_t PTPTSSR; - uint32_t RESERVED9[565]; - __IO uint32_t DMABMR; - __IO uint32_t DMATPDR; - __IO uint32_t DMARPDR; - __IO uint32_t DMARDLAR; - __IO uint32_t DMATDLAR; - __IO uint32_t DMASR; - __IO uint32_t DMAOMR; - __IO uint32_t DMAIER; - __IO uint32_t DMAMFBOCR; - __IO uint32_t DMARSWTR; - uint32_t RESERVED10[8]; - __IO uint32_t DMACHTDR; - __IO uint32_t DMACHRDR; - __IO uint32_t DMACHTBAR; - __IO uint32_t DMACHRBAR; -} ETH_TypeDef; - -/** - * @brief External Interrupt/Event Controller - */ - -typedef struct -{ - __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ - __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ - __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ - __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ - __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ - __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ -} EXTI_TypeDef; - -/** - * @brief FLASH Registers - */ - -typedef struct -{ - __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ - __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ - __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ - __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ - __IO uint32_t OPTCR; /*!< FLASH option control register , Address offset: 0x14 */ - __IO uint32_t OPTCR1; /*!< FLASH option control register 1, Address offset: 0x18 */ -} FLASH_TypeDef; - -/** - * @brief Flexible Memory Controller - */ - -typedef struct -{ - __IO uint32_t BTCR[8]; /*!< NOR/PSRAM chip-select control register(BCR) and chip-select timing register(BTR), Address offset: 0x00-1C */ -} FMC_Bank1_TypeDef; - -/** - * @brief Flexible Memory Controller Bank1E - */ - -typedef struct -{ - __IO uint32_t BWTR[7]; /*!< NOR/PSRAM write timing registers, Address offset: 0x104-0x11C */ -} FMC_Bank1E_TypeDef; - -/** - * @brief Flexible Memory Controller Bank3 - */ - -typedef struct -{ - __IO uint32_t PCR; /*!< NAND Flash control register, Address offset: 0x80 */ - __IO uint32_t SR; /*!< NAND Flash FIFO status and interrupt register, Address offset: 0x84 */ - __IO uint32_t PMEM; /*!< NAND Flash Common memory space timing register, Address offset: 0x88 */ - __IO uint32_t PATT; /*!< NAND Flash Attribute memory space timing register, Address offset: 0x8C */ - uint32_t RESERVED; /*!< Reserved, 0x90 */ - __IO uint32_t ECCR; /*!< NAND Flash ECC result registers, Address offset: 0x94 */ -} FMC_Bank3_TypeDef; - -/** - * @brief Flexible Memory Controller Bank5_6 - */ - -typedef struct -{ - __IO uint32_t SDCR[2]; /*!< SDRAM Control registers , Address offset: 0x140-0x144 */ - __IO uint32_t SDTR[2]; /*!< SDRAM Timing registers , Address offset: 0x148-0x14C */ - __IO uint32_t SDCMR; /*!< SDRAM Command Mode register, Address offset: 0x150 */ - __IO uint32_t SDRTR; /*!< SDRAM Refresh Timer register, Address offset: 0x154 */ - __IO uint32_t SDSR; /*!< SDRAM Status register, Address offset: 0x158 */ -} FMC_Bank5_6_TypeDef; - -/** - * @brief General Purpose I/O - */ - -typedef struct -{ - __IO uint32_t MODER; /*!< GPIO port mode register, Address offset: 0x00 */ - __IO uint32_t OTYPER; /*!< GPIO port output type register, Address offset: 0x04 */ - __IO uint32_t OSPEEDR; /*!< GPIO port output speed register, Address offset: 0x08 */ - __IO uint32_t PUPDR; /*!< GPIO port pull-up/pull-down register, Address offset: 0x0C */ - __IO uint32_t IDR; /*!< GPIO port input data register, Address offset: 0x10 */ - __IO uint32_t ODR; /*!< GPIO port output data register, Address offset: 0x14 */ - __IO uint32_t BSRR; /*!< GPIO port bit set/reset register, Address offset: 0x18 */ - __IO uint32_t LCKR; /*!< GPIO port configuration lock register, Address offset: 0x1C */ - __IO uint32_t AFR[2]; /*!< GPIO alternate function registers, Address offset: 0x20-0x24 */ -} GPIO_TypeDef; - -/** - * @brief System configuration controller - */ - -typedef struct -{ - __IO uint32_t MEMRMP; /*!< SYSCFG memory remap register, Address offset: 0x00 */ - __IO uint32_t PMC; /*!< SYSCFG peripheral mode configuration register, Address offset: 0x04 */ - __IO uint32_t EXTICR[4]; /*!< SYSCFG external interrupt configuration registers, Address offset: 0x08-0x14 */ - uint32_t RESERVED[2]; /*!< Reserved, 0x18-0x1C */ - __IO uint32_t CMPCR; /*!< SYSCFG Compensation cell control register, Address offset: 0x20 */ -} SYSCFG_TypeDef; - -/** - * @brief Inter-integrated Circuit Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< I2C Control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< I2C Control register 2, Address offset: 0x04 */ - __IO uint32_t OAR1; /*!< I2C Own address register 1, Address offset: 0x08 */ - __IO uint32_t OAR2; /*!< I2C Own address register 2, Address offset: 0x0C */ - __IO uint32_t DR; /*!< I2C Data register, Address offset: 0x10 */ - __IO uint32_t SR1; /*!< I2C Status register 1, Address offset: 0x14 */ - __IO uint32_t SR2; /*!< I2C Status register 2, Address offset: 0x18 */ - __IO uint32_t CCR; /*!< I2C Clock control register, Address offset: 0x1C */ - __IO uint32_t TRISE; /*!< I2C TRISE register, Address offset: 0x20 */ - __IO uint32_t FLTR; /*!< I2C FLTR register, Address offset: 0x24 */ -} I2C_TypeDef; - -/** - * @brief Independent WATCHDOG - */ - -typedef struct -{ - __IO uint32_t KR; /*!< IWDG Key register, Address offset: 0x00 */ - __IO uint32_t PR; /*!< IWDG Prescaler register, Address offset: 0x04 */ - __IO uint32_t RLR; /*!< IWDG Reload register, Address offset: 0x08 */ - __IO uint32_t SR; /*!< IWDG Status register, Address offset: 0x0C */ -} IWDG_TypeDef; - -/** - * @brief LCD-TFT Display Controller - */ - -typedef struct -{ - uint32_t RESERVED0[2]; /*!< Reserved, 0x00-0x04 */ - __IO uint32_t SSCR; /*!< LTDC Synchronization Size Configuration Register, Address offset: 0x08 */ - __IO uint32_t BPCR; /*!< LTDC Back Porch Configuration Register, Address offset: 0x0C */ - __IO uint32_t AWCR; /*!< LTDC Active Width Configuration Register, Address offset: 0x10 */ - __IO uint32_t TWCR; /*!< LTDC Total Width Configuration Register, Address offset: 0x14 */ - __IO uint32_t GCR; /*!< LTDC Global Control Register, Address offset: 0x18 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x1C-0x20 */ - __IO uint32_t SRCR; /*!< LTDC Shadow Reload Configuration Register, Address offset: 0x24 */ - uint32_t RESERVED2[1]; /*!< Reserved, 0x28 */ - __IO uint32_t BCCR; /*!< LTDC Background Color Configuration Register, Address offset: 0x2C */ - uint32_t RESERVED3[1]; /*!< Reserved, 0x30 */ - __IO uint32_t IER; /*!< LTDC Interrupt Enable Register, Address offset: 0x34 */ - __IO uint32_t ISR; /*!< LTDC Interrupt Status Register, Address offset: 0x38 */ - __IO uint32_t ICR; /*!< LTDC Interrupt Clear Register, Address offset: 0x3C */ - __IO uint32_t LIPCR; /*!< LTDC Line Interrupt Position Configuration Register, Address offset: 0x40 */ - __IO uint32_t CPSR; /*!< LTDC Current Position Status Register, Address offset: 0x44 */ - __IO uint32_t CDSR; /*!< LTDC Current Display Status Register, Address offset: 0x48 */ -} LTDC_TypeDef; - -/** - * @brief LCD-TFT Display layer x Controller - */ - -typedef struct -{ - __IO uint32_t CR; /*!< LTDC Layerx Control Register Address offset: 0x84 */ - __IO uint32_t WHPCR; /*!< LTDC Layerx Window Horizontal Position Configuration Register Address offset: 0x88 */ - __IO uint32_t WVPCR; /*!< LTDC Layerx Window Vertical Position Configuration Register Address offset: 0x8C */ - __IO uint32_t CKCR; /*!< LTDC Layerx Color Keying Configuration Register Address offset: 0x90 */ - __IO uint32_t PFCR; /*!< LTDC Layerx Pixel Format Configuration Register Address offset: 0x94 */ - __IO uint32_t CACR; /*!< LTDC Layerx Constant Alpha Configuration Register Address offset: 0x98 */ - __IO uint32_t DCCR; /*!< LTDC Layerx Default Color Configuration Register Address offset: 0x9C */ - __IO uint32_t BFCR; /*!< LTDC Layerx Blending Factors Configuration Register Address offset: 0xA0 */ - uint32_t RESERVED0[2]; /*!< Reserved */ - __IO uint32_t CFBAR; /*!< LTDC Layerx Color Frame Buffer Address Register Address offset: 0xAC */ - __IO uint32_t CFBLR; /*!< LTDC Layerx Color Frame Buffer Length Register Address offset: 0xB0 */ - __IO uint32_t CFBLNR; /*!< LTDC Layerx ColorFrame Buffer Line Number Register Address offset: 0xB4 */ - uint32_t RESERVED1[3]; /*!< Reserved */ - __IO uint32_t CLUTWR; /*!< LTDC Layerx CLUT Write Register Address offset: 0x144 */ - -} LTDC_Layer_TypeDef; - -/** - * @brief Power Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< PWR power control register, Address offset: 0x00 */ - __IO uint32_t CSR; /*!< PWR power control/status register, Address offset: 0x04 */ -} PWR_TypeDef; - -/** - * @brief Reset and Clock Control - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RCC clock control register, Address offset: 0x00 */ - __IO uint32_t PLLCFGR; /*!< RCC PLL configuration register, Address offset: 0x04 */ - __IO uint32_t CFGR; /*!< RCC clock configuration register, Address offset: 0x08 */ - __IO uint32_t CIR; /*!< RCC clock interrupt register, Address offset: 0x0C */ - __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, Address offset: 0x10 */ - __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, Address offset: 0x14 */ - __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, Address offset: 0x18 */ - uint32_t RESERVED0; /*!< Reserved, 0x1C */ - __IO uint32_t APB1RSTR; /*!< RCC APB1 peripheral reset register, Address offset: 0x20 */ - __IO uint32_t APB2RSTR; /*!< RCC APB2 peripheral reset register, Address offset: 0x24 */ - uint32_t RESERVED1[2]; /*!< Reserved, 0x28-0x2C */ - __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock register, Address offset: 0x30 */ - __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock register, Address offset: 0x34 */ - __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock register, Address offset: 0x38 */ - uint32_t RESERVED2; /*!< Reserved, 0x3C */ - __IO uint32_t APB1ENR; /*!< RCC APB1 peripheral clock enable register, Address offset: 0x40 */ - __IO uint32_t APB2ENR; /*!< RCC APB2 peripheral clock enable register, Address offset: 0x44 */ - uint32_t RESERVED3[2]; /*!< Reserved, 0x48-0x4C */ - __IO uint32_t AHB1LPENR; /*!< RCC AHB1 peripheral clock enable in low power mode register, Address offset: 0x50 */ - __IO uint32_t AHB2LPENR; /*!< RCC AHB2 peripheral clock enable in low power mode register, Address offset: 0x54 */ - __IO uint32_t AHB3LPENR; /*!< RCC AHB3 peripheral clock enable in low power mode register, Address offset: 0x58 */ - uint32_t RESERVED4; /*!< Reserved, 0x5C */ - __IO uint32_t APB1LPENR; /*!< RCC APB1 peripheral clock enable in low power mode register, Address offset: 0x60 */ - __IO uint32_t APB2LPENR; /*!< RCC APB2 peripheral clock enable in low power mode register, Address offset: 0x64 */ - uint32_t RESERVED5[2]; /*!< Reserved, 0x68-0x6C */ - __IO uint32_t BDCR; /*!< RCC Backup domain control register, Address offset: 0x70 */ - __IO uint32_t CSR; /*!< RCC clock control & status register, Address offset: 0x74 */ - uint32_t RESERVED6[2]; /*!< Reserved, 0x78-0x7C */ - __IO uint32_t SSCGR; /*!< RCC spread spectrum clock generation register, Address offset: 0x80 */ - __IO uint32_t PLLI2SCFGR; /*!< RCC PLLI2S configuration register, Address offset: 0x84 */ - __IO uint32_t PLLSAICFGR; /*!< RCC PLLSAI configuration register, Address offset: 0x88 */ - __IO uint32_t DCKCFGR; /*!< RCC Dedicated Clocks configuration register, Address offset: 0x8C */ - -} RCC_TypeDef; - -/** - * @brief Real-Time Clock - */ - -typedef struct -{ - __IO uint32_t TR; /*!< RTC time register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< RTC date register, Address offset: 0x04 */ - __IO uint32_t CR; /*!< RTC control register, Address offset: 0x08 */ - __IO uint32_t ISR; /*!< RTC initialization and status register, Address offset: 0x0C */ - __IO uint32_t PRER; /*!< RTC prescaler register, Address offset: 0x10 */ - __IO uint32_t WUTR; /*!< RTC wakeup timer register, Address offset: 0x14 */ - __IO uint32_t CALIBR; /*!< RTC calibration register, Address offset: 0x18 */ - __IO uint32_t ALRMAR; /*!< RTC alarm A register, Address offset: 0x1C */ - __IO uint32_t ALRMBR; /*!< RTC alarm B register, Address offset: 0x20 */ - __IO uint32_t WPR; /*!< RTC write protection register, Address offset: 0x24 */ - __IO uint32_t SSR; /*!< RTC sub second register, Address offset: 0x28 */ - __IO uint32_t SHIFTR; /*!< RTC shift control register, Address offset: 0x2C */ - __IO uint32_t TSTR; /*!< RTC time stamp time register, Address offset: 0x30 */ - __IO uint32_t TSDR; /*!< RTC time stamp date register, Address offset: 0x34 */ - __IO uint32_t TSSSR; /*!< RTC time-stamp sub second register, Address offset: 0x38 */ - __IO uint32_t CALR; /*!< RTC calibration register, Address offset: 0x3C */ - __IO uint32_t TAFCR; /*!< RTC tamper and alternate function configuration register, Address offset: 0x40 */ - __IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */ - __IO uint32_t ALRMBSSR;/*!< RTC alarm B sub second register, Address offset: 0x48 */ - uint32_t RESERVED7; /*!< Reserved, 0x4C */ - __IO uint32_t BKP0R; /*!< RTC backup register 1, Address offset: 0x50 */ - __IO uint32_t BKP1R; /*!< RTC backup register 1, Address offset: 0x54 */ - __IO uint32_t BKP2R; /*!< RTC backup register 2, Address offset: 0x58 */ - __IO uint32_t BKP3R; /*!< RTC backup register 3, Address offset: 0x5C */ - __IO uint32_t BKP4R; /*!< RTC backup register 4, Address offset: 0x60 */ - __IO uint32_t BKP5R; /*!< RTC backup register 5, Address offset: 0x64 */ - __IO uint32_t BKP6R; /*!< RTC backup register 6, Address offset: 0x68 */ - __IO uint32_t BKP7R; /*!< RTC backup register 7, Address offset: 0x6C */ - __IO uint32_t BKP8R; /*!< RTC backup register 8, Address offset: 0x70 */ - __IO uint32_t BKP9R; /*!< RTC backup register 9, Address offset: 0x74 */ - __IO uint32_t BKP10R; /*!< RTC backup register 10, Address offset: 0x78 */ - __IO uint32_t BKP11R; /*!< RTC backup register 11, Address offset: 0x7C */ - __IO uint32_t BKP12R; /*!< RTC backup register 12, Address offset: 0x80 */ - __IO uint32_t BKP13R; /*!< RTC backup register 13, Address offset: 0x84 */ - __IO uint32_t BKP14R; /*!< RTC backup register 14, Address offset: 0x88 */ - __IO uint32_t BKP15R; /*!< RTC backup register 15, Address offset: 0x8C */ - __IO uint32_t BKP16R; /*!< RTC backup register 16, Address offset: 0x90 */ - __IO uint32_t BKP17R; /*!< RTC backup register 17, Address offset: 0x94 */ - __IO uint32_t BKP18R; /*!< RTC backup register 18, Address offset: 0x98 */ - __IO uint32_t BKP19R; /*!< RTC backup register 19, Address offset: 0x9C */ -} RTC_TypeDef; - -/** - * @brief Serial Audio Interface - */ - -typedef struct -{ - __IO uint32_t GCR; /*!< SAI global configuration register, Address offset: 0x00 */ -} SAI_TypeDef; - -typedef struct -{ - __IO uint32_t CR1; /*!< SAI block x configuration register 1, Address offset: 0x04 */ - __IO uint32_t CR2; /*!< SAI block x configuration register 2, Address offset: 0x08 */ - __IO uint32_t FRCR; /*!< SAI block x frame configuration register, Address offset: 0x0C */ - __IO uint32_t SLOTR; /*!< SAI block x slot register, Address offset: 0x10 */ - __IO uint32_t IMR; /*!< SAI block x interrupt mask register, Address offset: 0x14 */ - __IO uint32_t SR; /*!< SAI block x status register, Address offset: 0x18 */ - __IO uint32_t CLRFR; /*!< SAI block x clear flag register, Address offset: 0x1C */ - __IO uint32_t DR; /*!< SAI block x data register, Address offset: 0x20 */ -} SAI_Block_TypeDef; - -/** - * @brief SD host Interface - */ - -typedef struct -{ - __IO uint32_t POWER; /*!< SDIO power control register, Address offset: 0x00 */ - __IO uint32_t CLKCR; /*!< SDI clock control register, Address offset: 0x04 */ - __IO uint32_t ARG; /*!< SDIO argument register, Address offset: 0x08 */ - __IO uint32_t CMD; /*!< SDIO command register, Address offset: 0x0C */ - __I uint32_t RESPCMD; /*!< SDIO command response register, Address offset: 0x10 */ - __I uint32_t RESP1; /*!< SDIO response 1 register, Address offset: 0x14 */ - __I uint32_t RESP2; /*!< SDIO response 2 register, Address offset: 0x18 */ - __I uint32_t RESP3; /*!< SDIO response 3 register, Address offset: 0x1C */ - __I uint32_t RESP4; /*!< SDIO response 4 register, Address offset: 0x20 */ - __IO uint32_t DTIMER; /*!< SDIO data timer register, Address offset: 0x24 */ - __IO uint32_t DLEN; /*!< SDIO data length register, Address offset: 0x28 */ - __IO uint32_t DCTRL; /*!< SDIO data control register, Address offset: 0x2C */ - __I uint32_t DCOUNT; /*!< SDIO data counter register, Address offset: 0x30 */ - __I uint32_t STA; /*!< SDIO status register, Address offset: 0x34 */ - __IO uint32_t ICR; /*!< SDIO interrupt clear register, Address offset: 0x38 */ - __IO uint32_t MASK; /*!< SDIO mask register, Address offset: 0x3C */ - uint32_t RESERVED0[2]; /*!< Reserved, 0x40-0x44 */ - __I uint32_t FIFOCNT; /*!< SDIO FIFO counter register, Address offset: 0x48 */ - uint32_t RESERVED1[13]; /*!< Reserved, 0x4C-0x7C */ - __IO uint32_t FIFO; /*!< SDIO data FIFO register, Address offset: 0x80 */ -} SDIO_TypeDef; - -/** - * @brief Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< SPI control register 1 (not used in I2S mode), Address offset: 0x00 */ - __IO uint32_t CR2; /*!< SPI control register 2, Address offset: 0x04 */ - __IO uint32_t SR; /*!< SPI status register, Address offset: 0x08 */ - __IO uint32_t DR; /*!< SPI data register, Address offset: 0x0C */ - __IO uint32_t CRCPR; /*!< SPI CRC polynomial register (not used in I2S mode), Address offset: 0x10 */ - __IO uint32_t RXCRCR; /*!< SPI RX CRC register (not used in I2S mode), Address offset: 0x14 */ - __IO uint32_t TXCRCR; /*!< SPI TX CRC register (not used in I2S mode), Address offset: 0x18 */ - __IO uint32_t I2SCFGR; /*!< SPI_I2S configuration register, Address offset: 0x1C */ - __IO uint32_t I2SPR; /*!< SPI_I2S prescaler register, Address offset: 0x20 */ -} SPI_TypeDef; - -/** - * @brief QUAD Serial Peripheral Interface - */ - -typedef struct -{ - __IO uint32_t CR; /*!< QUADSPI Control register, Address offset: 0x00 */ - __IO uint32_t DCR; /*!< QUADSPI Device Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< QUADSPI Status register, Address offset: 0x08 */ - __IO uint32_t FCR; /*!< QUADSPI Flag Clear register, Address offset: 0x0C */ - __IO uint32_t DLR; /*!< QUADSPI Data Length register, Address offset: 0x10 */ - __IO uint32_t CCR; /*!< QUADSPI Communication Configuration register, Address offset: 0x14 */ - __IO uint32_t AR; /*!< QUADSPI Address register, Address offset: 0x18 */ - __IO uint32_t ABR; /*!< QUADSPI Alternate Bytes register, Address offset: 0x1C */ - __IO uint32_t DR; /*!< QUADSPI Data register, Address offset: 0x20 */ - __IO uint32_t PSMKR; /*!< QUADSPI Polling Status Mask register, Address offset: 0x24 */ - __IO uint32_t PSMAR; /*!< QUADSPI Polling Status Match register, Address offset: 0x28 */ - __IO uint32_t PIR; /*!< QUADSPI Polling Interval register, Address offset: 0x2C */ - __IO uint32_t LPTR; /*!< QUADSPI Low Power Timeout register, Address offset: 0x30 */ -} QUADSPI_TypeDef; - -/** - * @brief TIM - */ - -typedef struct -{ - __IO uint32_t CR1; /*!< TIM control register 1, Address offset: 0x00 */ - __IO uint32_t CR2; /*!< TIM control register 2, Address offset: 0x04 */ - __IO uint32_t SMCR; /*!< TIM slave mode control register, Address offset: 0x08 */ - __IO uint32_t DIER; /*!< TIM DMA/interrupt enable register, Address offset: 0x0C */ - __IO uint32_t SR; /*!< TIM status register, Address offset: 0x10 */ - __IO uint32_t EGR; /*!< TIM event generation register, Address offset: 0x14 */ - __IO uint32_t CCMR1; /*!< TIM capture/compare mode register 1, Address offset: 0x18 */ - __IO uint32_t CCMR2; /*!< TIM capture/compare mode register 2, Address offset: 0x1C */ - __IO uint32_t CCER; /*!< TIM capture/compare enable register, Address offset: 0x20 */ - __IO uint32_t CNT; /*!< TIM counter register, Address offset: 0x24 */ - __IO uint32_t PSC; /*!< TIM prescaler, Address offset: 0x28 */ - __IO uint32_t ARR; /*!< TIM auto-reload register, Address offset: 0x2C */ - __IO uint32_t RCR; /*!< TIM repetition counter register, Address offset: 0x30 */ - __IO uint32_t CCR1; /*!< TIM capture/compare register 1, Address offset: 0x34 */ - __IO uint32_t CCR2; /*!< TIM capture/compare register 2, Address offset: 0x38 */ - __IO uint32_t CCR3; /*!< TIM capture/compare register 3, Address offset: 0x3C */ - __IO uint32_t CCR4; /*!< TIM capture/compare register 4, Address offset: 0x40 */ - __IO uint32_t BDTR; /*!< TIM break and dead-time register, Address offset: 0x44 */ - __IO uint32_t DCR; /*!< TIM DMA control register, Address offset: 0x48 */ - __IO uint32_t DMAR; /*!< TIM DMA address for full transfer, Address offset: 0x4C */ - __IO uint32_t OR; /*!< TIM option register, Address offset: 0x50 */ -} TIM_TypeDef; - -/** - * @brief Universal Synchronous Asynchronous Receiver Transmitter - */ - -typedef struct -{ - __IO uint32_t SR; /*!< USART Status register, Address offset: 0x00 */ - __IO uint32_t DR; /*!< USART Data register, Address offset: 0x04 */ - __IO uint32_t BRR; /*!< USART Baud rate register, Address offset: 0x08 */ - __IO uint32_t CR1; /*!< USART Control register 1, Address offset: 0x0C */ - __IO uint32_t CR2; /*!< USART Control register 2, Address offset: 0x10 */ - __IO uint32_t CR3; /*!< USART Control register 3, Address offset: 0x14 */ - __IO uint32_t GTPR; /*!< USART Guard time and prescaler register, Address offset: 0x18 */ -} USART_TypeDef; - -/** - * @brief Window WATCHDOG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< WWDG Control register, Address offset: 0x00 */ - __IO uint32_t CFR; /*!< WWDG Configuration register, Address offset: 0x04 */ - __IO uint32_t SR; /*!< WWDG Status register, Address offset: 0x08 */ -} WWDG_TypeDef; - -/** - * @brief Crypto Processor - */ - -typedef struct -{ - __IO uint32_t CR; /*!< CRYP control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< CRYP status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< CRYP data input register, Address offset: 0x08 */ - __IO uint32_t DOUT; /*!< CRYP data output register, Address offset: 0x0C */ - __IO uint32_t DMACR; /*!< CRYP DMA control register, Address offset: 0x10 */ - __IO uint32_t IMSCR; /*!< CRYP interrupt mask set/clear register, Address offset: 0x14 */ - __IO uint32_t RISR; /*!< CRYP raw interrupt status register, Address offset: 0x18 */ - __IO uint32_t MISR; /*!< CRYP masked interrupt status register, Address offset: 0x1C */ - __IO uint32_t K0LR; /*!< CRYP key left register 0, Address offset: 0x20 */ - __IO uint32_t K0RR; /*!< CRYP key right register 0, Address offset: 0x24 */ - __IO uint32_t K1LR; /*!< CRYP key left register 1, Address offset: 0x28 */ - __IO uint32_t K1RR; /*!< CRYP key right register 1, Address offset: 0x2C */ - __IO uint32_t K2LR; /*!< CRYP key left register 2, Address offset: 0x30 */ - __IO uint32_t K2RR; /*!< CRYP key right register 2, Address offset: 0x34 */ - __IO uint32_t K3LR; /*!< CRYP key left register 3, Address offset: 0x38 */ - __IO uint32_t K3RR; /*!< CRYP key right register 3, Address offset: 0x3C */ - __IO uint32_t IV0LR; /*!< CRYP initialization vector left-word register 0, Address offset: 0x40 */ - __IO uint32_t IV0RR; /*!< CRYP initialization vector right-word register 0, Address offset: 0x44 */ - __IO uint32_t IV1LR; /*!< CRYP initialization vector left-word register 1, Address offset: 0x48 */ - __IO uint32_t IV1RR; /*!< CRYP initialization vector right-word register 1, Address offset: 0x4C */ - __IO uint32_t CSGCMCCM0R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 0, Address offset: 0x50 */ - __IO uint32_t CSGCMCCM1R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 1, Address offset: 0x54 */ - __IO uint32_t CSGCMCCM2R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 2, Address offset: 0x58 */ - __IO uint32_t CSGCMCCM3R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 3, Address offset: 0x5C */ - __IO uint32_t CSGCMCCM4R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 4, Address offset: 0x60 */ - __IO uint32_t CSGCMCCM5R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 5, Address offset: 0x64 */ - __IO uint32_t CSGCMCCM6R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 6, Address offset: 0x68 */ - __IO uint32_t CSGCMCCM7R; /*!< CRYP GCM/GMAC or CCM/CMAC context swap register 7, Address offset: 0x6C */ - __IO uint32_t CSGCM0R; /*!< CRYP GCM/GMAC context swap register 0, Address offset: 0x70 */ - __IO uint32_t CSGCM1R; /*!< CRYP GCM/GMAC context swap register 1, Address offset: 0x74 */ - __IO uint32_t CSGCM2R; /*!< CRYP GCM/GMAC context swap register 2, Address offset: 0x78 */ - __IO uint32_t CSGCM3R; /*!< CRYP GCM/GMAC context swap register 3, Address offset: 0x7C */ - __IO uint32_t CSGCM4R; /*!< CRYP GCM/GMAC context swap register 4, Address offset: 0x80 */ - __IO uint32_t CSGCM5R; /*!< CRYP GCM/GMAC context swap register 5, Address offset: 0x84 */ - __IO uint32_t CSGCM6R; /*!< CRYP GCM/GMAC context swap register 6, Address offset: 0x88 */ - __IO uint32_t CSGCM7R; /*!< CRYP GCM/GMAC context swap register 7, Address offset: 0x8C */ -} CRYP_TypeDef; - -/** - * @brief HASH - */ - -typedef struct -{ - __IO uint32_t CR; /*!< HASH control register, Address offset: 0x00 */ - __IO uint32_t DIN; /*!< HASH data input register, Address offset: 0x04 */ - __IO uint32_t STR; /*!< HASH start register, Address offset: 0x08 */ - __IO uint32_t HR[5]; /*!< HASH digest registers, Address offset: 0x0C-0x1C */ - __IO uint32_t IMR; /*!< HASH interrupt enable register, Address offset: 0x20 */ - __IO uint32_t SR; /*!< HASH status register, Address offset: 0x24 */ - uint32_t RESERVED[52]; /*!< Reserved, 0x28-0xF4 */ - __IO uint32_t CSR[54]; /*!< HASH context swap registers, Address offset: 0x0F8-0x1CC */ -} HASH_TypeDef; - -/** - * @brief HASH_DIGEST - */ - -typedef struct -{ - __IO uint32_t HR[8]; /*!< HASH digest registers, Address offset: 0x310-0x32C */ -} HASH_DIGEST_TypeDef; - -/** - * @brief RNG - */ - -typedef struct -{ - __IO uint32_t CR; /*!< RNG control register, Address offset: 0x00 */ - __IO uint32_t SR; /*!< RNG status register, Address offset: 0x04 */ - __IO uint32_t DR; /*!< RNG data register, Address offset: 0x08 */ -} RNG_TypeDef; - - -/** - * @brief USB_OTG_Core_Registers - */ -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register 000h */ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register 004h */ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register 008h */ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register 00Ch */ - __IO uint32_t GRSTCTL; /*!< Core Reset Register 010h */ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register 014h */ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register 018h */ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register 01Ch */ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register 020h */ - __IO uint32_t GRXFSIZ; /*!< Receive FIFO Size Register 024h */ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register 028h */ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg 02Ch */ - uint32_t Reserved30[2]; /*!< Reserved 030h */ - __IO uint32_t GCCFG; /*!< General Purpose IO Register 038h */ - __IO uint32_t CID; /*!< User ID Register 03Ch */ - uint32_t Reserved5[3]; /*!< Reserved 040h-048h */ - __IO uint32_t GHWCFG3; /*!< User HW config3 04Ch */ - uint32_t Reserved6; /*!< Reserved 050h */ - __IO uint32_t GLPMCFG; /*!< LPM Register 054h */ - uint32_t Reserved; /*!< Reserved 058h */ - __IO uint32_t GDFIFOCFG; /*!< DFIFO Software Config Register 05Ch */ - uint32_t Reserved43[40]; /*!< Reserved 058h-0FFh */ - __IO uint32_t HPTXFSIZ; /*!< Host Periodic Tx FIFO Size Reg 100h */ - __IO uint32_t DIEPTXF[0x0F]; /*!< dev Periodic Transmit FIFO */ -} USB_OTG_GlobalTypeDef; - -/** - * @brief USB_OTG_device_Registers - */ -typedef struct -{ - __IO uint32_t DCFG; /*!< dev Configuration Register 800h */ - __IO uint32_t DCTL; /*!< dev Control Register 804h */ - __IO uint32_t DSTS; /*!< dev Status Register (RO) 808h */ - uint32_t Reserved0C; /*!< Reserved 80Ch */ - __IO uint32_t DIEPMSK; /*!< dev IN Endpoint Mask 810h */ - __IO uint32_t DOEPMSK; /*!< dev OUT Endpoint Mask 814h */ - __IO uint32_t DAINT; /*!< dev All Endpoints Itr Reg 818h */ - __IO uint32_t DAINTMSK; /*!< dev All Endpoints Itr Mask 81Ch */ - uint32_t Reserved20; /*!< Reserved 820h */ - uint32_t Reserved9; /*!< Reserved 824h */ - __IO uint32_t DVBUSDIS; /*!< dev VBUS discharge Register 828h */ - __IO uint32_t DVBUSPULSE; /*!< dev VBUS Pulse Register 82Ch */ - __IO uint32_t DTHRCTL; /*!< dev threshold 830h */ - __IO uint32_t DIEPEMPMSK; /*!< dev empty msk 834h */ - __IO uint32_t DEACHINT; /*!< dedicated EP interrupt 838h */ - __IO uint32_t DEACHMSK; /*!< dedicated EP msk 83Ch */ - uint32_t Reserved40; /*!< dedicated EP mask 840h */ - __IO uint32_t DINEP1MSK; /*!< dedicated EP mask 844h */ - uint32_t Reserved44[15]; /*!< Reserved 844-87Ch */ - __IO uint32_t DOUTEP1MSK; /*!< dedicated EP msk 884h */ -} USB_OTG_DeviceTypeDef; - -/** - * @brief USB_OTG_IN_Endpoint-Specific_Register - */ -typedef struct -{ - __IO uint32_t DIEPCTL; /*!< dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /*!< Reserved 900h + (ep_num * 20h) + 04h */ - __IO uint32_t DIEPINT; /*!< dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /*!< Reserved 900h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DIEPTSIZ; /*!< IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h */ - __IO uint32_t DIEPDMA; /*!< IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h */ - __IO uint32_t DTXFSTS; /*!< IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h */ - uint32_t Reserved18; /*!< Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch */ -} USB_OTG_INEndpointTypeDef; - -/** - * @brief USB_OTG_OUT_Endpoint-Specific_Registers - */ -typedef struct -{ - __IO uint32_t DOEPCTL; /*!< dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h */ - uint32_t Reserved04; /*!< Reserved B00h + (ep_num * 20h) + 04h */ - __IO uint32_t DOEPINT; /*!< dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h */ - uint32_t Reserved0C; /*!< Reserved B00h + (ep_num * 20h) + 0Ch */ - __IO uint32_t DOEPTSIZ; /*!< dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h */ - __IO uint32_t DOEPDMA; /*!< dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h */ - uint32_t Reserved18[2]; /*!< Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch */ -} USB_OTG_OUTEndpointTypeDef; - -/** - * @brief USB_OTG_Host_Mode_Register_Structures - */ -typedef struct -{ - __IO uint32_t HCFG; /*!< Host Configuration Register 400h */ - __IO uint32_t HFIR; /*!< Host Frame Interval Register 404h */ - __IO uint32_t HFNUM; /*!< Host Frame Nbr/Frame Remaining 408h */ - uint32_t Reserved40C; /*!< Reserved 40Ch */ - __IO uint32_t HPTXSTS; /*!< Host Periodic Tx FIFO/ Queue Status 410h */ - __IO uint32_t HAINT; /*!< Host All Channels Interrupt Register 414h */ - __IO uint32_t HAINTMSK; /*!< Host All Channels Interrupt Mask 418h */ -} USB_OTG_HostTypeDef; - -/** - * @brief USB_OTG_Host_Channel_Specific_Registers - */ -typedef struct -{ - __IO uint32_t HCCHAR; /*!< Host Channel Characteristics Register 500h */ - __IO uint32_t HCSPLT; /*!< Host Channel Split Control Register 504h */ - __IO uint32_t HCINT; /*!< Host Channel Interrupt Register 508h */ - __IO uint32_t HCINTMSK; /*!< Host Channel Interrupt Mask Register 50Ch */ - __IO uint32_t HCTSIZ; /*!< Host Channel Transfer Size Register 510h */ - __IO uint32_t HCDMA; /*!< Host Channel DMA Address Register 514h */ - uint32_t Reserved[2]; /*!< Reserved */ -} USB_OTG_HostChannelTypeDef; - -/** - * @} - */ - -/** @addtogroup Peripheral_memory_map - * @{ - */ -#define FLASH_BASE 0x08000000U /*!< FLASH(up to 1 MB) base address in the alias region */ -#define CCMDATARAM_BASE 0x10000000U /*!< CCM(core coupled memory) data RAM(64 KB) base address in the alias region */ -#define SRAM1_BASE 0x20000000U /*!< SRAM1(160 KB) base address in the alias region */ -#define SRAM2_BASE 0x20028000U /*!< SRAM2(32 KB) base address in the alias region */ -#define SRAM3_BASE 0x20030000U /*!< SRAM3(128 KB) base address in the alias region */ -#define PERIPH_BASE 0x40000000U /*!< Peripheral base address in the alias region */ -#define BKPSRAM_BASE 0x40024000U /*!< Backup SRAM(4 KB) base address in the alias region */ -#define FMC_R_BASE 0xA0000000U /*!< FMC registers base address */ -#define QSPI_R_BASE 0xA0001000U /*!< QuadSPI registers base address */ -#define SRAM1_BB_BASE 0x22000000U /*!< SRAM1(112 KB) base address in the bit-band region */ -#define SRAM2_BB_BASE 0x22500000U /*!< SRAM2(16 KB) base address in the bit-band region */ -#define SRAM3_BB_BASE 0x22600000U /*!< SRAM3(64 KB) base address in the bit-band region */ -#define PERIPH_BB_BASE 0x42000000U /*!< Peripheral base address in the bit-band region */ -#define BKPSRAM_BB_BASE 0x42480000U /*!< Backup SRAM(4 KB) base address in the bit-band region */ -#define FLASH_END 0x081FFFFFU /*!< FLASH end address */ -#define CCMDATARAM_END 0x1000FFFFU /*!< CCM data RAM end address */ - -/* Legacy defines */ -#define SRAM_BASE SRAM1_BASE -#define SRAM_BB_BASE SRAM1_BB_BASE - - -/*!< Peripheral memory map */ -#define APB1PERIPH_BASE PERIPH_BASE -#define APB2PERIPH_BASE (PERIPH_BASE + 0x00010000U) -#define AHB1PERIPH_BASE (PERIPH_BASE + 0x00020000U) -#define AHB2PERIPH_BASE (PERIPH_BASE + 0x10000000U) - -/*!< APB1 peripherals */ -#define TIM2_BASE (APB1PERIPH_BASE + 0x0000U) -#define TIM3_BASE (APB1PERIPH_BASE + 0x0400U) -#define TIM4_BASE (APB1PERIPH_BASE + 0x0800U) -#define TIM5_BASE (APB1PERIPH_BASE + 0x0C00U) -#define TIM6_BASE (APB1PERIPH_BASE + 0x1000U) -#define TIM7_BASE (APB1PERIPH_BASE + 0x1400U) -#define TIM12_BASE (APB1PERIPH_BASE + 0x1800U) -#define TIM13_BASE (APB1PERIPH_BASE + 0x1C00U) -#define TIM14_BASE (APB1PERIPH_BASE + 0x2000U) -#define RTC_BASE (APB1PERIPH_BASE + 0x2800U) -#define WWDG_BASE (APB1PERIPH_BASE + 0x2C00U) -#define IWDG_BASE (APB1PERIPH_BASE + 0x3000U) -#define I2S2ext_BASE (APB1PERIPH_BASE + 0x3400U) -#define SPI2_BASE (APB1PERIPH_BASE + 0x3800U) -#define SPI3_BASE (APB1PERIPH_BASE + 0x3C00U) -#define I2S3ext_BASE (APB1PERIPH_BASE + 0x4000U) -#define USART2_BASE (APB1PERIPH_BASE + 0x4400U) -#define USART3_BASE (APB1PERIPH_BASE + 0x4800U) -#define UART4_BASE (APB1PERIPH_BASE + 0x4C00U) -#define UART5_BASE (APB1PERIPH_BASE + 0x5000U) -#define I2C1_BASE (APB1PERIPH_BASE + 0x5400U) -#define I2C2_BASE (APB1PERIPH_BASE + 0x5800U) -#define I2C3_BASE (APB1PERIPH_BASE + 0x5C00U) -#define CAN1_BASE (APB1PERIPH_BASE + 0x6400U) -#define CAN2_BASE (APB1PERIPH_BASE + 0x6800U) -#define PWR_BASE (APB1PERIPH_BASE + 0x7000U) -#define DAC_BASE (APB1PERIPH_BASE + 0x7400U) -#define UART7_BASE (APB1PERIPH_BASE + 0x7800U) -#define UART8_BASE (APB1PERIPH_BASE + 0x7C00U) - -/*!< APB2 peripherals */ -#define TIM1_BASE (APB2PERIPH_BASE + 0x0000U) -#define TIM8_BASE (APB2PERIPH_BASE + 0x0400U) -#define USART1_BASE (APB2PERIPH_BASE + 0x1000U) -#define USART6_BASE (APB2PERIPH_BASE + 0x1400U) -#define ADC1_BASE (APB2PERIPH_BASE + 0x2000U) -#define ADC2_BASE (APB2PERIPH_BASE + 0x2100U) -#define ADC3_BASE (APB2PERIPH_BASE + 0x2200U) -#define ADC_BASE (APB2PERIPH_BASE + 0x2300U) -#define SDIO_BASE (APB2PERIPH_BASE + 0x2C00U) -#define SPI1_BASE (APB2PERIPH_BASE + 0x3000U) -#define SPI4_BASE (APB2PERIPH_BASE + 0x3400U) -#define SYSCFG_BASE (APB2PERIPH_BASE + 0x3800U) -#define EXTI_BASE (APB2PERIPH_BASE + 0x3C00U) -#define TIM9_BASE (APB2PERIPH_BASE + 0x4000U) -#define TIM10_BASE (APB2PERIPH_BASE + 0x4400U) -#define TIM11_BASE (APB2PERIPH_BASE + 0x4800U) -#define SPI5_BASE (APB2PERIPH_BASE + 0x5000U) -#define SPI6_BASE (APB2PERIPH_BASE + 0x5400U) -#define SAI1_BASE (APB2PERIPH_BASE + 0x5800U) -#define SAI1_Block_A_BASE (SAI1_BASE + 0x004U) -#define SAI1_Block_B_BASE (SAI1_BASE + 0x024U) -#define LTDC_BASE (APB2PERIPH_BASE + 0x6800U) -#define LTDC_Layer1_BASE (LTDC_BASE + 0x84U) -#define LTDC_Layer2_BASE (LTDC_BASE + 0x104U) -#define DSI_BASE (APB2PERIPH_BASE + 0x6C00U) - -/*!< AHB1 peripherals */ -#define GPIOA_BASE (AHB1PERIPH_BASE + 0x0000U) -#define GPIOB_BASE (AHB1PERIPH_BASE + 0x0400U) -#define GPIOC_BASE (AHB1PERIPH_BASE + 0x0800U) -#define GPIOD_BASE (AHB1PERIPH_BASE + 0x0C00U) -#define GPIOE_BASE (AHB1PERIPH_BASE + 0x1000U) -#define GPIOF_BASE (AHB1PERIPH_BASE + 0x1400U) -#define GPIOG_BASE (AHB1PERIPH_BASE + 0x1800U) -#define GPIOH_BASE (AHB1PERIPH_BASE + 0x1C00U) -#define GPIOI_BASE (AHB1PERIPH_BASE + 0x2000U) -#define GPIOJ_BASE (AHB1PERIPH_BASE + 0x2400U) -#define GPIOK_BASE (AHB1PERIPH_BASE + 0x2800U) -#define CRC_BASE (AHB1PERIPH_BASE + 0x3000U) -#define RCC_BASE (AHB1PERIPH_BASE + 0x3800U) -#define FLASH_R_BASE (AHB1PERIPH_BASE + 0x3C00U) -#define DMA1_BASE (AHB1PERIPH_BASE + 0x6000U) -#define DMA1_Stream0_BASE (DMA1_BASE + 0x010U) -#define DMA1_Stream1_BASE (DMA1_BASE + 0x028U) -#define DMA1_Stream2_BASE (DMA1_BASE + 0x040U) -#define DMA1_Stream3_BASE (DMA1_BASE + 0x058U) -#define DMA1_Stream4_BASE (DMA1_BASE + 0x070U) -#define DMA1_Stream5_BASE (DMA1_BASE + 0x088U) -#define DMA1_Stream6_BASE (DMA1_BASE + 0x0A0U) -#define DMA1_Stream7_BASE (DMA1_BASE + 0x0B8U) -#define DMA2_BASE (AHB1PERIPH_BASE + 0x6400U) -#define DMA2_Stream0_BASE (DMA2_BASE + 0x010U) -#define DMA2_Stream1_BASE (DMA2_BASE + 0x028U) -#define DMA2_Stream2_BASE (DMA2_BASE + 0x040U) -#define DMA2_Stream3_BASE (DMA2_BASE + 0x058U) -#define DMA2_Stream4_BASE (DMA2_BASE + 0x070U) -#define DMA2_Stream5_BASE (DMA2_BASE + 0x088U) -#define DMA2_Stream6_BASE (DMA2_BASE + 0x0A0U) -#define DMA2_Stream7_BASE (DMA2_BASE + 0x0B8U) -#define ETH_BASE (AHB1PERIPH_BASE + 0x8000U) -#define ETH_MAC_BASE (ETH_BASE) -#define ETH_MMC_BASE (ETH_BASE + 0x0100U) -#define ETH_PTP_BASE (ETH_BASE + 0x0700U) -#define ETH_DMA_BASE (ETH_BASE + 0x1000U) -#define DMA2D_BASE (AHB1PERIPH_BASE + 0xB000U) - -/*!< AHB2 peripherals */ -#define DCMI_BASE (AHB2PERIPH_BASE + 0x50000U) -#define CRYP_BASE (AHB2PERIPH_BASE + 0x60000U) -#define HASH_BASE (AHB2PERIPH_BASE + 0x60400U) -#define HASH_DIGEST_BASE (AHB2PERIPH_BASE + 0x60710U) -#define RNG_BASE (AHB2PERIPH_BASE + 0x60800U) - -/*!< FMC Bankx registers base address */ -#define FMC_Bank1_R_BASE (FMC_R_BASE + 0x0000U) -#define FMC_Bank1E_R_BASE (FMC_R_BASE + 0x0104U) -#define FMC_Bank3_R_BASE (FMC_R_BASE + 0x0080U) -#define FMC_Bank5_6_R_BASE (FMC_R_BASE + 0x0140U) - -/*!< Debug MCU registers base address */ -#define DBGMCU_BASE 0xE0042000U - -/*!< USB registers base address */ -#define USB_OTG_HS_PERIPH_BASE 0x40040000U -#define USB_OTG_FS_PERIPH_BASE 0x50000000U - -#define USB_OTG_GLOBAL_BASE 0x000U -#define USB_OTG_DEVICE_BASE 0x800U -#define USB_OTG_IN_ENDPOINT_BASE 0x900U -#define USB_OTG_OUT_ENDPOINT_BASE 0xB00U -#define USB_OTG_EP_REG_SIZE 0x20U -#define USB_OTG_HOST_BASE 0x400U -#define USB_OTG_HOST_PORT_BASE 0x440U -#define USB_OTG_HOST_CHANNEL_BASE 0x500U -#define USB_OTG_HOST_CHANNEL_SIZE 0x20U -#define USB_OTG_PCGCCTL_BASE 0xE00U -#define USB_OTG_FIFO_BASE 0x1000U -#define USB_OTG_FIFO_SIZE 0x1000U - -/** - * @} - */ - -/** @addtogroup Peripheral_declaration - * @{ - */ -#define TIM2 ((TIM_TypeDef *) TIM2_BASE) -#define TIM3 ((TIM_TypeDef *) TIM3_BASE) -#define TIM4 ((TIM_TypeDef *) TIM4_BASE) -#define TIM5 ((TIM_TypeDef *) TIM5_BASE) -#define TIM6 ((TIM_TypeDef *) TIM6_BASE) -#define TIM7 ((TIM_TypeDef *) TIM7_BASE) -#define TIM12 ((TIM_TypeDef *) TIM12_BASE) -#define TIM13 ((TIM_TypeDef *) TIM13_BASE) -#define TIM14 ((TIM_TypeDef *) TIM14_BASE) -#define RTC ((RTC_TypeDef *) RTC_BASE) -#define WWDG ((WWDG_TypeDef *) WWDG_BASE) -#define IWDG ((IWDG_TypeDef *) IWDG_BASE) -#define I2S2ext ((SPI_TypeDef *) I2S2ext_BASE) -#define SPI2 ((SPI_TypeDef *) SPI2_BASE) -#define SPI3 ((SPI_TypeDef *) SPI3_BASE) -#define I2S3ext ((SPI_TypeDef *) I2S3ext_BASE) -#define USART2 ((USART_TypeDef *) USART2_BASE) -#define USART3 ((USART_TypeDef *) USART3_BASE) -#define UART4 ((USART_TypeDef *) UART4_BASE) -#define UART5 ((USART_TypeDef *) UART5_BASE) -#define I2C1 ((I2C_TypeDef *) I2C1_BASE) -#define I2C2 ((I2C_TypeDef *) I2C2_BASE) -#define I2C3 ((I2C_TypeDef *) I2C3_BASE) -#define CAN1 ((CAN_TypeDef *) CAN1_BASE) -#define CAN2 ((CAN_TypeDef *) CAN2_BASE) -#define PWR ((PWR_TypeDef *) PWR_BASE) -#define DAC ((DAC_TypeDef *) DAC_BASE) -#define UART7 ((USART_TypeDef *) UART7_BASE) -#define UART8 ((USART_TypeDef *) UART8_BASE) -#define TIM1 ((TIM_TypeDef *) TIM1_BASE) -#define TIM8 ((TIM_TypeDef *) TIM8_BASE) -#define USART1 ((USART_TypeDef *) USART1_BASE) -#define USART6 ((USART_TypeDef *) USART6_BASE) -#define ADC ((ADC_Common_TypeDef *) ADC_BASE) -#define ADC1 ((ADC_TypeDef *) ADC1_BASE) -#define ADC2 ((ADC_TypeDef *) ADC2_BASE) -#define ADC3 ((ADC_TypeDef *) ADC3_BASE) -#define SDIO ((SDIO_TypeDef *) SDIO_BASE) -#define SPI1 ((SPI_TypeDef *) SPI1_BASE) -#define SPI4 ((SPI_TypeDef *) SPI4_BASE) -#define SYSCFG ((SYSCFG_TypeDef *) SYSCFG_BASE) -#define EXTI ((EXTI_TypeDef *) EXTI_BASE) -#define TIM9 ((TIM_TypeDef *) TIM9_BASE) -#define TIM10 ((TIM_TypeDef *) TIM10_BASE) -#define TIM11 ((TIM_TypeDef *) TIM11_BASE) -#define SPI5 ((SPI_TypeDef *) SPI5_BASE) -#define SPI6 ((SPI_TypeDef *) SPI6_BASE) -#define SAI1 ((SAI_TypeDef *) SAI1_BASE) -#define SAI1_Block_A ((SAI_Block_TypeDef *)SAI1_Block_A_BASE) -#define SAI1_Block_B ((SAI_Block_TypeDef *)SAI1_Block_B_BASE) -#define LTDC ((LTDC_TypeDef *)LTDC_BASE) -#define LTDC_Layer1 ((LTDC_Layer_TypeDef *)LTDC_Layer1_BASE) -#define LTDC_Layer2 ((LTDC_Layer_TypeDef *)LTDC_Layer2_BASE) -#define DSI ((DSI_TypeDef *)DSI_BASE) - -#define GPIOA ((GPIO_TypeDef *) GPIOA_BASE) -#define GPIOB ((GPIO_TypeDef *) GPIOB_BASE) -#define GPIOC ((GPIO_TypeDef *) GPIOC_BASE) -#define GPIOD ((GPIO_TypeDef *) GPIOD_BASE) -#define GPIOE ((GPIO_TypeDef *) GPIOE_BASE) -#define GPIOF ((GPIO_TypeDef *) GPIOF_BASE) -#define GPIOG ((GPIO_TypeDef *) GPIOG_BASE) -#define GPIOH ((GPIO_TypeDef *) GPIOH_BASE) -#define GPIOI ((GPIO_TypeDef *) GPIOI_BASE) -#define GPIOJ ((GPIO_TypeDef *) GPIOJ_BASE) -#define GPIOK ((GPIO_TypeDef *) GPIOK_BASE) -#define CRC ((CRC_TypeDef *) CRC_BASE) -#define RCC ((RCC_TypeDef *) RCC_BASE) -#define FLASH ((FLASH_TypeDef *) FLASH_R_BASE) -#define DMA1 ((DMA_TypeDef *) DMA1_BASE) -#define DMA1_Stream0 ((DMA_Stream_TypeDef *) DMA1_Stream0_BASE) -#define DMA1_Stream1 ((DMA_Stream_TypeDef *) DMA1_Stream1_BASE) -#define DMA1_Stream2 ((DMA_Stream_TypeDef *) DMA1_Stream2_BASE) -#define DMA1_Stream3 ((DMA_Stream_TypeDef *) DMA1_Stream3_BASE) -#define DMA1_Stream4 ((DMA_Stream_TypeDef *) DMA1_Stream4_BASE) -#define DMA1_Stream5 ((DMA_Stream_TypeDef *) DMA1_Stream5_BASE) -#define DMA1_Stream6 ((DMA_Stream_TypeDef *) DMA1_Stream6_BASE) -#define DMA1_Stream7 ((DMA_Stream_TypeDef *) DMA1_Stream7_BASE) -#define DMA2 ((DMA_TypeDef *) DMA2_BASE) -#define DMA2_Stream0 ((DMA_Stream_TypeDef *) DMA2_Stream0_BASE) -#define DMA2_Stream1 ((DMA_Stream_TypeDef *) DMA2_Stream1_BASE) -#define DMA2_Stream2 ((DMA_Stream_TypeDef *) DMA2_Stream2_BASE) -#define DMA2_Stream3 ((DMA_Stream_TypeDef *) DMA2_Stream3_BASE) -#define DMA2_Stream4 ((DMA_Stream_TypeDef *) DMA2_Stream4_BASE) -#define DMA2_Stream5 ((DMA_Stream_TypeDef *) DMA2_Stream5_BASE) -#define DMA2_Stream6 ((DMA_Stream_TypeDef *) DMA2_Stream6_BASE) -#define DMA2_Stream7 ((DMA_Stream_TypeDef *) DMA2_Stream7_BASE) -#define ETH ((ETH_TypeDef *) ETH_BASE) -#define DMA2D ((DMA2D_TypeDef *)DMA2D_BASE) -#define DCMI ((DCMI_TypeDef *) DCMI_BASE) -#define CRYP ((CRYP_TypeDef *) CRYP_BASE) -#define HASH ((HASH_TypeDef *) HASH_BASE) -#define HASH_DIGEST ((HASH_DIGEST_TypeDef *) HASH_DIGEST_BASE) -#define RNG ((RNG_TypeDef *) RNG_BASE) -#define FMC_Bank1 ((FMC_Bank1_TypeDef *) FMC_Bank1_R_BASE) -#define FMC_Bank1E ((FMC_Bank1E_TypeDef *) FMC_Bank1E_R_BASE) -#define FMC_Bank3 ((FMC_Bank3_TypeDef *) FMC_Bank3_R_BASE) -#define FMC_Bank5_6 ((FMC_Bank5_6_TypeDef *) FMC_Bank5_6_R_BASE) -#define QUADSPI ((QUADSPI_TypeDef *) QSPI_R_BASE) - -#define DBGMCU ((DBGMCU_TypeDef *) DBGMCU_BASE) - -#define USB_OTG_FS ((USB_OTG_GlobalTypeDef *) USB_OTG_FS_PERIPH_BASE) -#define USB_OTG_HS ((USB_OTG_GlobalTypeDef *) USB_OTG_HS_PERIPH_BASE) - -/** - * @} - */ - -/** @addtogroup Exported_constants - * @{ - */ - -/** @addtogroup Peripheral_Registers_Bits_Definition -* @{ -*/ - -/******************************************************************************/ -/* Peripheral Registers_Bits_Definition */ -/******************************************************************************/ - -/******************************************************************************/ -/* */ -/* Analog to Digital Converter */ -/* */ -/******************************************************************************/ -/******************** Bit definition for ADC_SR register ********************/ -#define ADC_SR_AWD 0x00000001U /*!
© COPYRIGHT(c) 2016 STMicroelectronics
- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f4xx - * @{ - */ - -#ifndef __STM32F4xx_H -#define __STM32F4xx_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - -/** @addtogroup Library_configuration_section - * @{ - */ - -/** - * @brief STM32 Family - */ -#if !defined (STM32F4) -#define STM32F4 -#endif /* STM32F4 */ - -/* Uncomment the line below according to the target STM32 device used in your - application - */ -#if !defined (STM32F405xx) && !defined (STM32F415xx) && !defined (STM32F407xx) && !defined (STM32F417xx) && \ - !defined (STM32F427xx) && !defined (STM32F437xx) && !defined (STM32F429xx) && !defined (STM32F439xx) && \ - !defined (STM32F401xC) && !defined (STM32F401xE) && !defined (STM32F410Tx) && !defined (STM32F410Cx) && \ - !defined (STM32F410Rx) && !defined (STM32F411xE) && !defined (STM32F446xx) && !defined (STM32F469xx) && \ - !defined (STM32F479xx) && !defined (STM32F412Cx) && !defined (STM32F412Rx) && !defined (STM32F412Vx) && \ - !defined (STM32F412Zx) -/* #define STM32F405xx */ /*!< STM32F405RG, STM32F405VG and STM32F405ZG Devices */ -/* #define STM32F415xx */ /*!< STM32F415RG, STM32F415VG and STM32F415ZG Devices */ -/* #define STM32F407xx */ /*!< STM32F407VG, STM32F407VE, STM32F407ZG, STM32F407ZE, STM32F407IG and STM32F407IE Devices */ -/* #define STM32F417xx */ /*!< STM32F417VG, STM32F417VE, STM32F417ZG, STM32F417ZE, STM32F417IG and STM32F417IE Devices */ -/* #define STM32F427xx */ /*!< STM32F427VG, STM32F427VI, STM32F427ZG, STM32F427ZI, STM32F427IG and STM32F427II Devices */ -/* #define STM32F437xx */ /*!< STM32F437VG, STM32F437VI, STM32F437ZG, STM32F437ZI, STM32F437IG and STM32F437II Devices */ -/* #define STM32F429xx */ /*!< STM32F429VG, STM32F429VI, STM32F429ZG, STM32F429ZI, STM32F429BG, STM32F429BI, STM32F429NG, - STM32F439NI, STM32F429IG and STM32F429II Devices */ -/* #define STM32F439xx */ /*!< STM32F439VG, STM32F439VI, STM32F439ZG, STM32F439ZI, STM32F439BG, STM32F439BI, STM32F439NG, - STM32F439NI, STM32F439IG and STM32F439II Devices */ -/* #define STM32F401xC */ /*!< STM32F401CB, STM32F401CC, STM32F401RB, STM32F401RC, STM32F401VB and STM32F401VC Devices */ -/* #define STM32F401xE */ /*!< STM32F401CD, STM32F401RD, STM32F401VD, STM32F401CE, STM32F401RE and STM32F401VE Devices */ -/* #define STM32F410Tx */ /*!< STM32F410T8 and STM32F410TB Devices */ -/* #define STM32F410Cx */ /*!< STM32F410C8 and STM32F410CB Devices */ -/* #define STM32F410Rx */ /*!< STM32F410R8 and STM32F410RB Devices */ -/* #define STM32F411xE */ /*!< STM32F411CC, STM32F411RC, STM32F411VC, STM32F411CE, STM32F411RE and STM32F411VE Devices */ -/* #define STM32F446xx */ /*!< STM32F446MC, STM32F446ME, STM32F446RC, STM32F446RE, STM32F446VC, STM32F446VE, STM32F446ZC, - and STM32F446ZE Devices */ -/* #define STM32F469xx */ /*!< STM32F469AI, STM32F469II, STM32F469BI, STM32F469NI, STM32F469AG, STM32F469IG, STM32F469BG, - STM32F469NG, STM32F469AE, STM32F469IE, STM32F469BE and STM32F469NE Devices */ -/* #define STM32F479xx */ /*!< STM32F479AI, STM32F479II, STM32F479BI, STM32F479NI, STM32F479AG, STM32F479IG, STM32F479BG - and STM32F479NG Devices */ -/* #define STM32F412Cx */ /*!< STM32F412CEU and STM32F412CGU Devices */ -/* #define STM32F412Zx */ /*!< STM32F412ZET, STM32F412ZGT, STM32F412ZEJ and STM32F412ZGJ Devices */ -/* #define STM32F412Vx */ /*!< STM32F412VET, STM32F412VGT, STM32F412VEH and STM32F412VGH Devices */ -/* #define STM32F412Rx */ /*!< STM32F412RET, STM32F412RGT, STM32F412REY and STM32F412RGY Devices */ -#endif - -/* Tip: To avoid modifying this file each time you need to switch between these - devices, you can define the device in your toolchain compiler preprocessor. - */ -#if !defined (USE_HAL_DRIVER) -/** - * @brief Comment the line below if you will not use the peripherals drivers. - In this case, these drivers will not be included and the application code will - be based on direct access to peripherals registers - */ -/*#define USE_HAL_DRIVER */ -#endif /* USE_HAL_DRIVER */ - -/** - * @brief CMSIS version number V2.5.0 - */ -#define __STM32F4xx_CMSIS_VERSION_MAIN (0x02U) /*!< [31:24] main version */ -#define __STM32F4xx_CMSIS_VERSION_SUB1 (0x05U) /*!< [23:16] sub1 version */ -#define __STM32F4xx_CMSIS_VERSION_SUB2 (0x00U) /*!< [15:8] sub2 version */ -#define __STM32F4xx_CMSIS_VERSION_RC (0x00U) /*!< [7:0] release candidate */ -#define __STM32F4xx_CMSIS_VERSION ((__STM32F4xx_CMSIS_VERSION_MAIN << 24)\ - |(__STM32F4xx_CMSIS_VERSION_SUB1 << 16)\ - |(__STM32F4xx_CMSIS_VERSION_SUB2 << 8 )\ - |(__STM32F4xx_CMSIS_VERSION)) - -/** - * @} - */ - -/** @addtogroup Device_Included - * @{ - */ - -#if defined(STM32F405xx) -#include "stm32f405xx.h" -#elif defined(STM32F415xx) -#include "stm32f415xx.h" -#elif defined(STM32F407xx) -#include "stm32f407xx.h" -#elif defined(STM32F417xx) -#include "stm32f417xx.h" -#elif defined(STM32F427xx) -#include "stm32f427xx.h" -#elif defined(STM32F437xx) -#include "stm32f437xx.h" -#elif defined(STM32F429xx) -#include "stm32f429xx.h" -#elif defined(STM32F439xx) -#include "stm32f439xx.h" -#elif defined(STM32F401xC) -#include "stm32f401xc.h" -#elif defined(STM32F401xE) -#include "stm32f401xe.h" -#elif defined(STM32F410Tx) -#include "stm32f410tx.h" -#elif defined(STM32F410Cx) -#include "stm32f410cx.h" -#elif defined(STM32F410Rx) -#include "stm32f410rx.h" -#elif defined(STM32F411xE) -#include "stm32f411xe.h" -#elif defined(STM32F446xx) -#include "stm32f446xx.h" -#elif defined(STM32F469xx) -#include "stm32f469xx.h" -#elif defined(STM32F479xx) -#include "stm32f479xx.h" -#elif defined(STM32F412Cx) -#include "stm32f412cx.h" -#elif defined(STM32F412Zx) -#include "stm32f412zx.h" -#elif defined(STM32F412Rx) -#include "stm32f412rx.h" -#elif defined(STM32F412Vx) -#include "stm32f412vx.h" -#else -#error "Please select first the target STM32F4xx device used in your application (in stm32f4xx.h file)" -#endif - -/** - * @} - */ - -/** @addtogroup Exported_types - * @{ - */ -typedef enum -{ - RESET = 0U, - SET = !RESET -} FlagStatus, ITStatus; - -typedef enum -{ - DISABLE = 0U, - ENABLE = !DISABLE -} FunctionalState; -#define IS_FUNCTIONAL_STATE(STATE) (((STATE) == DISABLE) || ((STATE) == ENABLE)) - -typedef enum -{ - ERROR = 0U, - SUCCESS = !ERROR -} ErrorStatus; - -/** - * @} - */ - - -/** @addtogroup Exported_macro - * @{ - */ -#define SET_BIT(REG, BIT) ((REG) |= (BIT)) - -#define CLEAR_BIT(REG, BIT) ((REG) &= ~(BIT)) - -#define READ_BIT(REG, BIT) ((REG) & (BIT)) - -#define CLEAR_REG(REG) ((REG) = (0x0)) - -#define WRITE_REG(REG, VAL) ((REG) = (VAL)) - -#define READ_REG(REG) ((REG)) - -#define MODIFY_REG(REG, CLEARMASK, SETMASK) WRITE_REG((REG), (((READ_REG(REG)) & (~(CLEARMASK))) | (SETMASK))) - -#define POSITION_VAL(VAL) (__CLZ(__RBIT(VAL))) - - -/** - * @} - */ - -#if defined (USE_HAL_DRIVER) -#include "stm32f4xx_hal.h" -#endif /* USE_HAL_DRIVER */ - -#ifdef __cplusplus -} -#endif /* __cplusplus */ - -#endif /* __STM32F4xx_H */ -/** - * @} - */ - -/** - * @} - */ - - - - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F4xx/Include/system_stm32f4xx.h b/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F4xx/Include/system_stm32f4xx.h deleted file mode 100644 index 1a238e6e..00000000 --- a/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F4xx/Include/system_stm32f4xx.h +++ /dev/null @@ -1,122 +0,0 @@ -/** - ****************************************************************************** - * @file system_stm32f4xx.h - * @author MCD Application Team - * @version V2.5.0 - * @date 22-April-2016 - * @brief CMSIS Cortex-M4 Device System Source File for STM32F4xx devices. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f4xx_system - * @{ - */ - -/** - * @brief Define to prevent recursive inclusion - */ -#ifndef __SYSTEM_STM32F4XX_H -#define __SYSTEM_STM32F4XX_H - -#ifdef __cplusplus -extern "C" { -#endif - -/** @addtogroup STM32F4xx_System_Includes - * @{ - */ - -/** - * @} - */ - - -/** @addtogroup STM32F4xx_System_Exported_types - * @{ - */ -/* This variable is updated in three ways: - 1) by calling CMSIS function SystemCoreClockUpdate() - 2) by calling HAL API function HAL_RCC_GetSysClockFreq() - 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency - Note: If you use this function to configure the system clock; then there - is no need to call the 2 first functions listed above, since SystemCoreClock - variable is updated automatically. -*/ -extern uint32_t SystemCoreClock; /*!< System Clock Frequency (Core Clock) */ - - -/** - * @} - */ - -/** @addtogroup STM32F4xx_System_Exported_Constants - * @{ - */ - -/** - * @} - */ - -/** @addtogroup STM32F4xx_System_Exported_Macros - * @{ - */ - -/** - * @} - */ - -/** @addtogroup STM32F4xx_System_Exported_Functions - * @{ - */ - -extern void SystemInit(void); -extern void SystemCoreClockUpdate(void); -/** - * @} - */ - -#ifdef __cplusplus -} -#endif - -#endif /*__SYSTEM_STM32F4XX_H */ - -/** - * @} - */ - -/** - * @} - */ -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F4xx/Source/Templates/gcc/startup_stm32f407xx.s b/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F4xx/Source/Templates/gcc/startup_stm32f407xx.s deleted file mode 100644 index d211939b..00000000 --- a/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F4xx/Source/Templates/gcc/startup_stm32f407xx.s +++ /dev/null @@ -1,523 +0,0 @@ -/** - ****************************************************************************** - * @file startup_stm32f407xx.s - * @author MCD Application Team - * @version V2.5.0 - * @date 22-April-2015 - * @brief STM32F407xx Devices vector table for GCC based toolchains. - * This module performs: - * - Set the initial SP - * - Set the initial PC == Reset_Handler, - * - Set the vector table entries with the exceptions ISR address - * - Branches to main in the C library (which eventually - * calls main()). - * After Reset the Cortex-M4 processor is in Thread mode, - * priority is Privileged, and the Stack is set to Main. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - - .syntax unified - .cpu cortex-m4 - .fpu softvfp - .thumb - -.global g_pfnVectors -.global Default_Handler - -/* start address for the initialization values of the .data section. -defined in linker script */ -.word _sidata -/* start address for the .data section. defined in linker script */ -.word _sdata -/* end address for the .data section. defined in linker script */ -.word _edata -/* start address for the .bss section. defined in linker script */ -.word _sbss -/* end address for the .bss section. defined in linker script */ -.word _ebss -/* stack used for SystemInit_ExtMemCtl; always internal RAM used */ - -/** - * @brief This is the code that gets called when the processor first - * starts execution following a reset event. Only the absolutely - * necessary set is performed, after which the application - * supplied main() routine is called. - * @param None - * @retval : None -*/ - - .section .text.Reset_Handler - .weak Reset_Handler - .type Reset_Handler, %function -Reset_Handler: - ldr sp, =_estack /* set stack pointer */ - -/* Copy the data segment initializers from flash to SRAM */ - movs r1, #0 - b LoopCopyDataInit - -CopyDataInit: - ldr r3, =_sidata - ldr r3, [r3, r1] - str r3, [r0, r1] - adds r1, r1, #4 - -LoopCopyDataInit: - ldr r0, =_sdata - ldr r3, =_edata - adds r2, r0, r1 - cmp r2, r3 - bcc CopyDataInit - ldr r2, =_sbss - b LoopFillZerobss -/* Zero fill the bss segment. */ -FillZerobss: - movs r3, #0 - str r3, [r2], #4 - -LoopFillZerobss: - ldr r3, = _ebss - cmp r2, r3 - bcc FillZerobss - -/* Call the clock system intitialization function.*/ - bl SystemInit -/* Call static constructors */ - bl __libc_init_array -/* Call the application's entry point.*/ - bl main - bx lr -.size Reset_Handler, .-Reset_Handler - -/** - * @brief This is the code that gets called when the processor receives an - * unexpected interrupt. This simply enters an infinite loop, preserving - * the system state for examination by a debugger. - * @param None - * @retval None -*/ - .section .text.Default_Handler,"ax",%progbits -Default_Handler: -Infinite_Loop: - b Infinite_Loop - .size Default_Handler, .-Default_Handler -/****************************************************************************** -* -* The minimal vector table for a Cortex M3. Note that the proper constructs -* must be placed on this to ensure that it ends up at physical address -* 0x0000.0000. -* -*******************************************************************************/ - .section .isr_vector,"a",%progbits - .type g_pfnVectors, %object - .size g_pfnVectors, .-g_pfnVectors - - -g_pfnVectors: - .word _estack - .word Reset_Handler - .word NMI_Handler - .word HardFault_Handler - .word MemManage_Handler - .word BusFault_Handler - .word UsageFault_Handler - .word 0 - .word 0 - .word 0 - .word 0 - .word SVC_Handler - .word DebugMon_Handler - .word 0 - .word PendSV_Handler - .word SysTick_Handler - - /* External Interrupts */ - .word WWDG_IRQHandler /* Window WatchDog */ - .word PVD_IRQHandler /* PVD through EXTI Line detection */ - .word TAMP_STAMP_IRQHandler /* Tamper and TimeStamps through the EXTI line */ - .word RTC_WKUP_IRQHandler /* RTC Wakeup through the EXTI line */ - .word FLASH_IRQHandler /* FLASH */ - .word RCC_IRQHandler /* RCC */ - .word EXTI0_IRQHandler /* EXTI Line0 */ - .word EXTI1_IRQHandler /* EXTI Line1 */ - .word EXTI2_IRQHandler /* EXTI Line2 */ - .word EXTI3_IRQHandler /* EXTI Line3 */ - .word EXTI4_IRQHandler /* EXTI Line4 */ - .word DMA1_Stream0_IRQHandler /* DMA1 Stream 0 */ - .word DMA1_Stream1_IRQHandler /* DMA1 Stream 1 */ - .word DMA1_Stream2_IRQHandler /* DMA1 Stream 2 */ - .word DMA1_Stream3_IRQHandler /* DMA1 Stream 3 */ - .word DMA1_Stream4_IRQHandler /* DMA1 Stream 4 */ - .word DMA1_Stream5_IRQHandler /* DMA1 Stream 5 */ - .word DMA1_Stream6_IRQHandler /* DMA1 Stream 6 */ - .word ADC_IRQHandler /* ADC1, ADC2 and ADC3s */ - .word CAN1_TX_IRQHandler /* CAN1 TX */ - .word CAN1_RX0_IRQHandler /* CAN1 RX0 */ - .word CAN1_RX1_IRQHandler /* CAN1 RX1 */ - .word CAN1_SCE_IRQHandler /* CAN1 SCE */ - .word EXTI9_5_IRQHandler /* External Line[9:5]s */ - .word TIM1_BRK_TIM9_IRQHandler /* TIM1 Break and TIM9 */ - .word TIM1_UP_TIM10_IRQHandler /* TIM1 Update and TIM10 */ - .word TIM1_TRG_COM_TIM11_IRQHandler /* TIM1 Trigger and Commutation and TIM11 */ - .word TIM1_CC_IRQHandler /* TIM1 Capture Compare */ - .word TIM2_IRQHandler /* TIM2 */ - .word TIM3_IRQHandler /* TIM3 */ - .word TIM4_IRQHandler /* TIM4 */ - .word I2C1_EV_IRQHandler /* I2C1 Event */ - .word I2C1_ER_IRQHandler /* I2C1 Error */ - .word I2C2_EV_IRQHandler /* I2C2 Event */ - .word I2C2_ER_IRQHandler /* I2C2 Error */ - .word SPI1_IRQHandler /* SPI1 */ - .word SPI2_IRQHandler /* SPI2 */ - .word USART1_IRQHandler /* USART1 */ - .word USART2_IRQHandler /* USART2 */ - .word USART3_IRQHandler /* USART3 */ - .word EXTI15_10_IRQHandler /* External Line[15:10]s */ - .word RTC_Alarm_IRQHandler /* RTC Alarm (A and B) through EXTI Line */ - .word OTG_FS_WKUP_IRQHandler /* USB OTG FS Wakeup through EXTI line */ - .word TIM8_BRK_TIM12_IRQHandler /* TIM8 Break and TIM12 */ - .word TIM8_UP_TIM13_IRQHandler /* TIM8 Update and TIM13 */ - .word TIM8_TRG_COM_TIM14_IRQHandler /* TIM8 Trigger and Commutation and TIM14 */ - .word TIM8_CC_IRQHandler /* TIM8 Capture Compare */ - .word DMA1_Stream7_IRQHandler /* DMA1 Stream7 */ - .word FSMC_IRQHandler /* FSMC */ - .word SDIO_IRQHandler /* SDIO */ - .word TIM5_IRQHandler /* TIM5 */ - .word SPI3_IRQHandler /* SPI3 */ - .word UART4_IRQHandler /* UART4 */ - .word UART5_IRQHandler /* UART5 */ - .word TIM6_DAC_IRQHandler /* TIM6 and DAC1&2 underrun errors */ - .word TIM7_IRQHandler /* TIM7 */ - .word DMA2_Stream0_IRQHandler /* DMA2 Stream 0 */ - .word DMA2_Stream1_IRQHandler /* DMA2 Stream 1 */ - .word DMA2_Stream2_IRQHandler /* DMA2 Stream 2 */ - .word DMA2_Stream3_IRQHandler /* DMA2 Stream 3 */ - .word DMA2_Stream4_IRQHandler /* DMA2 Stream 4 */ - .word ETH_IRQHandler /* Ethernet */ - .word ETH_WKUP_IRQHandler /* Ethernet Wakeup through EXTI line */ - .word CAN2_TX_IRQHandler /* CAN2 TX */ - .word CAN2_RX0_IRQHandler /* CAN2 RX0 */ - .word CAN2_RX1_IRQHandler /* CAN2 RX1 */ - .word CAN2_SCE_IRQHandler /* CAN2 SCE */ - .word OTG_FS_IRQHandler /* USB OTG FS */ - .word DMA2_Stream5_IRQHandler /* DMA2 Stream 5 */ - .word DMA2_Stream6_IRQHandler /* DMA2 Stream 6 */ - .word DMA2_Stream7_IRQHandler /* DMA2 Stream 7 */ - .word USART6_IRQHandler /* USART6 */ - .word I2C3_EV_IRQHandler /* I2C3 event */ - .word I2C3_ER_IRQHandler /* I2C3 error */ - .word OTG_HS_EP1_OUT_IRQHandler /* USB OTG HS End Point 1 Out */ - .word OTG_HS_EP1_IN_IRQHandler /* USB OTG HS End Point 1 In */ - .word OTG_HS_WKUP_IRQHandler /* USB OTG HS Wakeup through EXTI */ - .word OTG_HS_IRQHandler /* USB OTG HS */ - .word DCMI_IRQHandler /* DCMI */ - .word 0 /* CRYP crypto */ - .word HASH_RNG_IRQHandler /* Hash and Rng */ - .word FPU_IRQHandler /* FPU */ - - -/******************************************************************************* -* -* Provide weak aliases for each Exception handler to the Default_Handler. -* As they are weak aliases, any function with the same name will override -* this definition. -* -*******************************************************************************/ - .weak NMI_Handler - .thumb_set NMI_Handler,Default_Handler - - .weak HardFault_Handler - .thumb_set HardFault_Handler,Default_Handler - - .weak MemManage_Handler - .thumb_set MemManage_Handler,Default_Handler - - .weak BusFault_Handler - .thumb_set BusFault_Handler,Default_Handler - - .weak UsageFault_Handler - .thumb_set UsageFault_Handler,Default_Handler - - .weak SVC_Handler - .thumb_set SVC_Handler,Default_Handler - - .weak DebugMon_Handler - .thumb_set DebugMon_Handler,Default_Handler - - .weak PendSV_Handler - .thumb_set PendSV_Handler,Default_Handler - - .weak SysTick_Handler - .thumb_set SysTick_Handler,Default_Handler - - .weak WWDG_IRQHandler - .thumb_set WWDG_IRQHandler,Default_Handler - - .weak PVD_IRQHandler - .thumb_set PVD_IRQHandler,Default_Handler - - .weak TAMP_STAMP_IRQHandler - .thumb_set TAMP_STAMP_IRQHandler,Default_Handler - - .weak RTC_WKUP_IRQHandler - .thumb_set RTC_WKUP_IRQHandler,Default_Handler - - .weak FLASH_IRQHandler - .thumb_set FLASH_IRQHandler,Default_Handler - - .weak RCC_IRQHandler - .thumb_set RCC_IRQHandler,Default_Handler - - .weak EXTI0_IRQHandler - .thumb_set EXTI0_IRQHandler,Default_Handler - - .weak EXTI1_IRQHandler - .thumb_set EXTI1_IRQHandler,Default_Handler - - .weak EXTI2_IRQHandler - .thumb_set EXTI2_IRQHandler,Default_Handler - - .weak EXTI3_IRQHandler - .thumb_set EXTI3_IRQHandler,Default_Handler - - .weak EXTI4_IRQHandler - .thumb_set EXTI4_IRQHandler,Default_Handler - - .weak DMA1_Stream0_IRQHandler - .thumb_set DMA1_Stream0_IRQHandler,Default_Handler - - .weak DMA1_Stream1_IRQHandler - .thumb_set DMA1_Stream1_IRQHandler,Default_Handler - - .weak DMA1_Stream2_IRQHandler - .thumb_set DMA1_Stream2_IRQHandler,Default_Handler - - .weak DMA1_Stream3_IRQHandler - .thumb_set DMA1_Stream3_IRQHandler,Default_Handler - - .weak DMA1_Stream4_IRQHandler - .thumb_set DMA1_Stream4_IRQHandler,Default_Handler - - .weak DMA1_Stream5_IRQHandler - .thumb_set DMA1_Stream5_IRQHandler,Default_Handler - - .weak DMA1_Stream6_IRQHandler - .thumb_set DMA1_Stream6_IRQHandler,Default_Handler - - .weak ADC_IRQHandler - .thumb_set ADC_IRQHandler,Default_Handler - - .weak CAN1_TX_IRQHandler - .thumb_set CAN1_TX_IRQHandler,Default_Handler - - .weak CAN1_RX0_IRQHandler - .thumb_set CAN1_RX0_IRQHandler,Default_Handler - - .weak CAN1_RX1_IRQHandler - .thumb_set CAN1_RX1_IRQHandler,Default_Handler - - .weak CAN1_SCE_IRQHandler - .thumb_set CAN1_SCE_IRQHandler,Default_Handler - - .weak EXTI9_5_IRQHandler - .thumb_set EXTI9_5_IRQHandler,Default_Handler - - .weak TIM1_BRK_TIM9_IRQHandler - .thumb_set TIM1_BRK_TIM9_IRQHandler,Default_Handler - - .weak TIM1_UP_TIM10_IRQHandler - .thumb_set TIM1_UP_TIM10_IRQHandler,Default_Handler - - .weak TIM1_TRG_COM_TIM11_IRQHandler - .thumb_set TIM1_TRG_COM_TIM11_IRQHandler,Default_Handler - - .weak TIM1_CC_IRQHandler - .thumb_set TIM1_CC_IRQHandler,Default_Handler - - .weak TIM2_IRQHandler - .thumb_set TIM2_IRQHandler,Default_Handler - - .weak TIM3_IRQHandler - .thumb_set TIM3_IRQHandler,Default_Handler - - .weak TIM4_IRQHandler - .thumb_set TIM4_IRQHandler,Default_Handler - - .weak I2C1_EV_IRQHandler - .thumb_set I2C1_EV_IRQHandler,Default_Handler - - .weak I2C1_ER_IRQHandler - .thumb_set I2C1_ER_IRQHandler,Default_Handler - - .weak I2C2_EV_IRQHandler - .thumb_set I2C2_EV_IRQHandler,Default_Handler - - .weak I2C2_ER_IRQHandler - .thumb_set I2C2_ER_IRQHandler,Default_Handler - - .weak SPI1_IRQHandler - .thumb_set SPI1_IRQHandler,Default_Handler - - .weak SPI2_IRQHandler - .thumb_set SPI2_IRQHandler,Default_Handler - - .weak USART1_IRQHandler - .thumb_set USART1_IRQHandler,Default_Handler - - .weak USART2_IRQHandler - .thumb_set USART2_IRQHandler,Default_Handler - - .weak USART3_IRQHandler - .thumb_set USART3_IRQHandler,Default_Handler - - .weak EXTI15_10_IRQHandler - .thumb_set EXTI15_10_IRQHandler,Default_Handler - - .weak RTC_Alarm_IRQHandler - .thumb_set RTC_Alarm_IRQHandler,Default_Handler - - .weak OTG_FS_WKUP_IRQHandler - .thumb_set OTG_FS_WKUP_IRQHandler,Default_Handler - - .weak TIM8_BRK_TIM12_IRQHandler - .thumb_set TIM8_BRK_TIM12_IRQHandler,Default_Handler - - .weak TIM8_UP_TIM13_IRQHandler - .thumb_set TIM8_UP_TIM13_IRQHandler,Default_Handler - - .weak TIM8_TRG_COM_TIM14_IRQHandler - .thumb_set TIM8_TRG_COM_TIM14_IRQHandler,Default_Handler - - .weak TIM8_CC_IRQHandler - .thumb_set TIM8_CC_IRQHandler,Default_Handler - - .weak DMA1_Stream7_IRQHandler - .thumb_set DMA1_Stream7_IRQHandler,Default_Handler - - .weak FSMC_IRQHandler - .thumb_set FSMC_IRQHandler,Default_Handler - - .weak SDIO_IRQHandler - .thumb_set SDIO_IRQHandler,Default_Handler - - .weak TIM5_IRQHandler - .thumb_set TIM5_IRQHandler,Default_Handler - - .weak SPI3_IRQHandler - .thumb_set SPI3_IRQHandler,Default_Handler - - .weak UART4_IRQHandler - .thumb_set UART4_IRQHandler,Default_Handler - - .weak UART5_IRQHandler - .thumb_set UART5_IRQHandler,Default_Handler - - .weak TIM6_DAC_IRQHandler - .thumb_set TIM6_DAC_IRQHandler,Default_Handler - - .weak TIM7_IRQHandler - .thumb_set TIM7_IRQHandler,Default_Handler - - .weak DMA2_Stream0_IRQHandler - .thumb_set DMA2_Stream0_IRQHandler,Default_Handler - - .weak DMA2_Stream1_IRQHandler - .thumb_set DMA2_Stream1_IRQHandler,Default_Handler - - .weak DMA2_Stream2_IRQHandler - .thumb_set DMA2_Stream2_IRQHandler,Default_Handler - - .weak DMA2_Stream3_IRQHandler - .thumb_set DMA2_Stream3_IRQHandler,Default_Handler - - .weak DMA2_Stream4_IRQHandler - .thumb_set DMA2_Stream4_IRQHandler,Default_Handler - - .weak ETH_IRQHandler - .thumb_set ETH_IRQHandler,Default_Handler - - .weak ETH_WKUP_IRQHandler - .thumb_set ETH_WKUP_IRQHandler,Default_Handler - - .weak CAN2_TX_IRQHandler - .thumb_set CAN2_TX_IRQHandler,Default_Handler - - .weak CAN2_RX0_IRQHandler - .thumb_set CAN2_RX0_IRQHandler,Default_Handler - - .weak CAN2_RX1_IRQHandler - .thumb_set CAN2_RX1_IRQHandler,Default_Handler - - .weak CAN2_SCE_IRQHandler - .thumb_set CAN2_SCE_IRQHandler,Default_Handler - - .weak OTG_FS_IRQHandler - .thumb_set OTG_FS_IRQHandler,Default_Handler - - .weak DMA2_Stream5_IRQHandler - .thumb_set DMA2_Stream5_IRQHandler,Default_Handler - - .weak DMA2_Stream6_IRQHandler - .thumb_set DMA2_Stream6_IRQHandler,Default_Handler - - .weak DMA2_Stream7_IRQHandler - .thumb_set DMA2_Stream7_IRQHandler,Default_Handler - - .weak USART6_IRQHandler - .thumb_set USART6_IRQHandler,Default_Handler - - .weak I2C3_EV_IRQHandler - .thumb_set I2C3_EV_IRQHandler,Default_Handler - - .weak I2C3_ER_IRQHandler - .thumb_set I2C3_ER_IRQHandler,Default_Handler - - .weak OTG_HS_EP1_OUT_IRQHandler - .thumb_set OTG_HS_EP1_OUT_IRQHandler,Default_Handler - - .weak OTG_HS_EP1_IN_IRQHandler - .thumb_set OTG_HS_EP1_IN_IRQHandler,Default_Handler - - .weak OTG_HS_WKUP_IRQHandler - .thumb_set OTG_HS_WKUP_IRQHandler,Default_Handler - - .weak OTG_HS_IRQHandler - .thumb_set OTG_HS_IRQHandler,Default_Handler - - .weak DCMI_IRQHandler - .thumb_set DCMI_IRQHandler,Default_Handler - - .weak HASH_RNG_IRQHandler - .thumb_set HASH_RNG_IRQHandler,Default_Handler - - .weak FPU_IRQHandler - .thumb_set FPU_IRQHandler,Default_Handler - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F4xx/Source/Templates/system_stm32f4xx.c b/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F4xx/Source/Templates/system_stm32f4xx.c deleted file mode 100644 index debc4d68..00000000 --- a/EpsilonLights/Drivers/CMSIS/Device/ST/STM32F4xx/Source/Templates/system_stm32f4xx.c +++ /dev/null @@ -1,729 +0,0 @@ -/** - ****************************************************************************** - * @file system_stm32f4xx.c - * @author MCD Application Team - * @version V2.5.0 - * @date 22-April-2016 - * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File. - * - * This file provides two functions and one global variable to be called from - * user application: - * - SystemInit(): This function is called at startup just after reset and - * before branch to main program. This call is made inside - * the "startup_stm32f4xx.s" file. - * - * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used - * by the user application to setup the SysTick - * timer or configure other parameters. - * - * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must - * be called whenever the core clock is changed - * during program execution. - * - * - ****************************************************************************** - * @attention - * - *

© COPYRIGHT 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f4xx_system - * @{ - */ - -/** @addtogroup STM32F4xx_System_Private_Includes - * @{ - */ - - -#include "stm32f4xx.h" - -#if !defined (HSE_VALUE) -#define HSE_VALUE ((uint32_t)25000000) /*!< Default value of the External oscillator in Hz */ -#endif /* HSE_VALUE */ - -#if !defined (HSI_VALUE) -#define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/ -#endif /* HSI_VALUE */ - -/** - * @} - */ - -/** @addtogroup STM32F4xx_System_Private_TypesDefinitions - * @{ - */ - -/** - * @} - */ - -/** @addtogroup STM32F4xx_System_Private_Defines - * @{ - */ - -/************************* Miscellaneous Configuration ************************/ -/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */ -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\ - || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\ - || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) -/* #define DATA_IN_ExtSRAM */ -#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\ - STM32F412Zx || STM32F412Vx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\ - || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) -/* #define DATA_IN_ExtSDRAM */ -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\ - STM32F479xx */ - -/*!< Uncomment the following line if you need to relocate your vector Table in - Internal SRAM. */ -/* #define VECT_TAB_SRAM */ -#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field. - This value must be a multiple of 0x200. */ -/******************************************************************************/ - -/** - * @} - */ - -/** @addtogroup STM32F4xx_System_Private_Macros - * @{ - */ - -/** - * @} - */ - -/** @addtogroup STM32F4xx_System_Private_Variables - * @{ - */ -/* This variable is updated in three ways: - 1) by calling CMSIS function SystemCoreClockUpdate() - 2) by calling HAL API function HAL_RCC_GetHCLKFreq() - 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency - Note: If you use this function to configure the system clock; then there - is no need to call the 2 first functions listed above, since SystemCoreClock - variable is updated automatically. -*/ -uint32_t SystemCoreClock = 16000000; -const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9}; - -/** - * @} - */ - -/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes - * @{ - */ - -#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM) -static void SystemInit_ExtMemCtl(void); -#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */ - -/** - * @} - */ - -/** @addtogroup STM32F4xx_System_Private_Functions - * @{ - */ - -/** - * @brief Setup the microcontroller system - * Initialize the FPU setting, vector table location and External memory - * configuration. - * @param None - * @retval None - */ -void SystemInit(void) -{ - /* FPU settings ------------------------------------------------------------*/ -#if (__FPU_PRESENT == 1) && (__FPU_USED == 1) - SCB->CPACR |= ((3UL << 10 * 2) | (3UL << 11 * 2)); /* set CP10 and CP11 Full Access */ -#endif - /* Reset the RCC clock configuration to the default reset state ------------*/ - /* Set HSION bit */ - RCC->CR |= (uint32_t)0x00000001; - /* Reset CFGR register */ - RCC->CFGR = 0x00000000; - /* Reset HSEON, CSSON and PLLON bits */ - RCC->CR &= (uint32_t)0xFEF6FFFF; - /* Reset PLLCFGR register */ - RCC->PLLCFGR = 0x24003010; - /* Reset HSEBYP bit */ - RCC->CR &= (uint32_t)0xFFFBFFFF; - /* Disable all interrupts */ - RCC->CIR = 0x00000000; -#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM) - SystemInit_ExtMemCtl(); -#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */ - /* Configure the Vector Table location add offset address ------------------*/ -#ifdef VECT_TAB_SRAM - SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */ -#else - SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */ -#endif -} - -/** - * @brief Update SystemCoreClock variable according to Clock Register Values. - * The SystemCoreClock variable contains the core clock (HCLK), it can - * be used by the user application to setup the SysTick timer or configure - * other parameters. - * - * @note Each time the core clock (HCLK) changes, this function must be called - * to update SystemCoreClock variable value. Otherwise, any configuration - * based on this variable will be incorrect. - * - * @note - The system frequency computed by this function is not the real - * frequency in the chip. It is calculated based on the predefined - * constant and the selected clock source: - * - * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*) - * - * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**) - * - * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) - * or HSI_VALUE(*) multiplied/divided by the PLL factors. - * - * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value - * 16 MHz) but the real value may vary depending on the variations - * in voltage and temperature. - * - * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value - * depends on the application requirements), user has to ensure that HSE_VALUE - * is same as the real frequency of the crystal used. Otherwise, this function - * may have wrong result. - * - * - The result of this function could be not correct when using fractional - * value for HSE crystal. - * - * @param None - * @retval None - */ -void SystemCoreClockUpdate(void) -{ - uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2; - /* Get SYSCLK source -------------------------------------------------------*/ - tmp = RCC->CFGR & RCC_CFGR_SWS; - - switch (tmp) - { - case 0x00: /* HSI used as system clock source */ - SystemCoreClock = HSI_VALUE; - break; - - case 0x04: /* HSE used as system clock source */ - SystemCoreClock = HSE_VALUE; - break; - - case 0x08: /* PLL used as system clock source */ - /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N - SYSCLK = PLL_VCO / PLL_P - */ - pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22; - pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM; - - if (pllsource != 0) - { - /* HSE used as PLL clock source */ - pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6); - } - else - { - /* HSI used as PLL clock source */ - pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6); - } - - pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >> 16) + 1 ) * 2; - SystemCoreClock = pllvco / pllp; - break; - - default: - SystemCoreClock = HSI_VALUE; - break; - } - - /* Compute HCLK frequency --------------------------------------------------*/ - /* Get HCLK prescaler */ - tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)]; - /* HCLK frequency */ - SystemCoreClock >>= tmp; -} - -#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM) -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F469xx) || defined(STM32F479xx) -/** - * @brief Setup the external memory controller. - * Called in startup_stm32f4xx.s before jump to main. - * This function configures the external memories (SRAM/SDRAM) - * This SRAM/SDRAM will be used as program data memory (including heap and stack). - * @param None - * @retval None - */ -void SystemInit_ExtMemCtl(void) -{ - __IO uint32_t tmp = 0x00; - register uint32_t tmpreg = 0, timeout = 0xFFFF; - register __IO uint32_t index; - /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */ - RCC->AHB1ENR |= 0x000001F8; - /* Delay after an RCC peripheral clock enabling */ - tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN); - /* Connect PDx pins to FMC Alternate function */ - GPIOD->AFR[0] = 0x00CCC0CC; - GPIOD->AFR[1] = 0xCCCCCCCC; - /* Configure PDx pins in Alternate function mode */ - GPIOD->MODER = 0xAAAA0A8A; - /* Configure PDx pins speed to 100 MHz */ - GPIOD->OSPEEDR = 0xFFFF0FCF; - /* Configure PDx pins Output type to push-pull */ - GPIOD->OTYPER = 0x00000000; - /* No pull-up, pull-down for PDx pins */ - GPIOD->PUPDR = 0x00000000; - /* Connect PEx pins to FMC Alternate function */ - GPIOE->AFR[0] = 0xC00CC0CC; - GPIOE->AFR[1] = 0xCCCCCCCC; - /* Configure PEx pins in Alternate function mode */ - GPIOE->MODER = 0xAAAA828A; - /* Configure PEx pins speed to 100 MHz */ - GPIOE->OSPEEDR = 0xFFFFC3CF; - /* Configure PEx pins Output type to push-pull */ - GPIOE->OTYPER = 0x00000000; - /* No pull-up, pull-down for PEx pins */ - GPIOE->PUPDR = 0x00000000; - /* Connect PFx pins to FMC Alternate function */ - GPIOF->AFR[0] = 0xCCCCCCCC; - GPIOF->AFR[1] = 0xCCCCCCCC; - /* Configure PFx pins in Alternate function mode */ - GPIOF->MODER = 0xAA800AAA; - /* Configure PFx pins speed to 50 MHz */ - GPIOF->OSPEEDR = 0xAA800AAA; - /* Configure PFx pins Output type to push-pull */ - GPIOF->OTYPER = 0x00000000; - /* No pull-up, pull-down for PFx pins */ - GPIOF->PUPDR = 0x00000000; - /* Connect PGx pins to FMC Alternate function */ - GPIOG->AFR[0] = 0xCCCCCCCC; - GPIOG->AFR[1] = 0xCCCCCCCC; - /* Configure PGx pins in Alternate function mode */ - GPIOG->MODER = 0xAAAAAAAA; - /* Configure PGx pins speed to 50 MHz */ - GPIOG->OSPEEDR = 0xAAAAAAAA; - /* Configure PGx pins Output type to push-pull */ - GPIOG->OTYPER = 0x00000000; - /* No pull-up, pull-down for PGx pins */ - GPIOG->PUPDR = 0x00000000; - /* Connect PHx pins to FMC Alternate function */ - GPIOH->AFR[0] = 0x00C0CC00; - GPIOH->AFR[1] = 0xCCCCCCCC; - /* Configure PHx pins in Alternate function mode */ - GPIOH->MODER = 0xAAAA08A0; - /* Configure PHx pins speed to 50 MHz */ - GPIOH->OSPEEDR = 0xAAAA08A0; - /* Configure PHx pins Output type to push-pull */ - GPIOH->OTYPER = 0x00000000; - /* No pull-up, pull-down for PHx pins */ - GPIOH->PUPDR = 0x00000000; - /* Connect PIx pins to FMC Alternate function */ - GPIOI->AFR[0] = 0xCCCCCCCC; - GPIOI->AFR[1] = 0x00000CC0; - /* Configure PIx pins in Alternate function mode */ - GPIOI->MODER = 0x0028AAAA; - /* Configure PIx pins speed to 50 MHz */ - GPIOI->OSPEEDR = 0x0028AAAA; - /* Configure PIx pins Output type to push-pull */ - GPIOI->OTYPER = 0x00000000; - /* No pull-up, pull-down for PIx pins */ - GPIOI->PUPDR = 0x00000000; - /*-- FMC Configuration -------------------------------------------------------*/ - /* Enable the FMC interface clock */ - RCC->AHB3ENR |= 0x00000001; - /* Delay after an RCC peripheral clock enabling */ - tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN); - FMC_Bank5_6->SDCR[0] = 0x000019E4; - FMC_Bank5_6->SDTR[0] = 0x01115351; - /* SDRAM initialization sequence */ - /* Clock enable command */ - FMC_Bank5_6->SDCMR = 0x00000011; - tmpreg = FMC_Bank5_6->SDSR & 0x00000020; - - while ((tmpreg != 0) && (timeout-- > 0)) - { - tmpreg = FMC_Bank5_6->SDSR & 0x00000020; - } - - /* Delay */ - for (index = 0; index < 1000; index++); - - /* PALL command */ - FMC_Bank5_6->SDCMR = 0x00000012; - timeout = 0xFFFF; - - while ((tmpreg != 0) && (timeout-- > 0)) - { - tmpreg = FMC_Bank5_6->SDSR & 0x00000020; - } - - /* Auto refresh command */ - FMC_Bank5_6->SDCMR = 0x00000073; - timeout = 0xFFFF; - - while ((tmpreg != 0) && (timeout-- > 0)) - { - tmpreg = FMC_Bank5_6->SDSR & 0x00000020; - } - - /* MRD register program */ - FMC_Bank5_6->SDCMR = 0x00046014; - timeout = 0xFFFF; - - while ((tmpreg != 0) && (timeout-- > 0)) - { - tmpreg = FMC_Bank5_6->SDSR & 0x00000020; - } - - /* Set refresh count */ - tmpreg = FMC_Bank5_6->SDRTR; - FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C << 1)); - /* Disable write protection */ - tmpreg = FMC_Bank5_6->SDCR[0]; - FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF); -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) - /* Configure and enable Bank1_SRAM2 */ - FMC_Bank1->BTCR[2] = 0x00001011; - FMC_Bank1->BTCR[3] = 0x00000201; - FMC_Bank1E->BWTR[2] = 0x0fffffff; -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */ -#if defined(STM32F469xx) || defined(STM32F479xx) - /* Configure and enable Bank1_SRAM2 */ - FMC_Bank1->BTCR[2] = 0x00001091; - FMC_Bank1->BTCR[3] = 0x00110212; - FMC_Bank1E->BWTR[2] = 0x0fffffff; -#endif /* STM32F469xx || STM32F479xx */ - (void)(tmp); -} -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ -#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM) -/** - * @brief Setup the external memory controller. - * Called in startup_stm32f4xx.s before jump to main. - * This function configures the external memories (SRAM/SDRAM) - * This SRAM/SDRAM will be used as program data memory (including heap and stack). - * @param None - * @retval None - */ -void SystemInit_ExtMemCtl(void) -{ - __IO uint32_t tmp = 0x00; -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\ - || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) -#if defined (DATA_IN_ExtSDRAM) - register uint32_t tmpreg = 0, timeout = 0xFFFF; - register __IO uint32_t index; -#if defined(STM32F446xx) - /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface - clock */ - RCC->AHB1ENR |= 0x0000007D; -#else - /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface - clock */ - RCC->AHB1ENR |= 0x000001F8; -#endif /* STM32F446xx */ - /* Delay after an RCC peripheral clock enabling */ - tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN); -#if defined(STM32F446xx) - /* Connect PAx pins to FMC Alternate function */ - GPIOA->AFR[0] |= 0xC0000000; - GPIOA->AFR[1] |= 0x00000000; - /* Configure PDx pins in Alternate function mode */ - GPIOA->MODER |= 0x00008000; - /* Configure PDx pins speed to 50 MHz */ - GPIOA->OSPEEDR |= 0x00008000; - /* Configure PDx pins Output type to push-pull */ - GPIOA->OTYPER |= 0x00000000; - /* No pull-up, pull-down for PDx pins */ - GPIOA->PUPDR |= 0x00000000; - /* Connect PCx pins to FMC Alternate function */ - GPIOC->AFR[0] |= 0x00CC0000; - GPIOC->AFR[1] |= 0x00000000; - /* Configure PDx pins in Alternate function mode */ - GPIOC->MODER |= 0x00000A00; - /* Configure PDx pins speed to 50 MHz */ - GPIOC->OSPEEDR |= 0x00000A00; - /* Configure PDx pins Output type to push-pull */ - GPIOC->OTYPER |= 0x00000000; - /* No pull-up, pull-down for PDx pins */ - GPIOC->PUPDR |= 0x00000000; -#endif /* STM32F446xx */ - /* Connect PDx pins to FMC Alternate function */ - GPIOD->AFR[0] = 0x000000CC; - GPIOD->AFR[1] = 0xCC000CCC; - /* Configure PDx pins in Alternate function mode */ - GPIOD->MODER = 0xA02A000A; - /* Configure PDx pins speed to 50 MHz */ - GPIOD->OSPEEDR = 0xA02A000A; - /* Configure PDx pins Output type to push-pull */ - GPIOD->OTYPER = 0x00000000; - /* No pull-up, pull-down for PDx pins */ - GPIOD->PUPDR = 0x00000000; - /* Connect PEx pins to FMC Alternate function */ - GPIOE->AFR[0] = 0xC00000CC; - GPIOE->AFR[1] = 0xCCCCCCCC; - /* Configure PEx pins in Alternate function mode */ - GPIOE->MODER = 0xAAAA800A; - /* Configure PEx pins speed to 50 MHz */ - GPIOE->OSPEEDR = 0xAAAA800A; - /* Configure PEx pins Output type to push-pull */ - GPIOE->OTYPER = 0x00000000; - /* No pull-up, pull-down for PEx pins */ - GPIOE->PUPDR = 0x00000000; - /* Connect PFx pins to FMC Alternate function */ - GPIOF->AFR[0] = 0xCCCCCCCC; - GPIOF->AFR[1] = 0xCCCCCCCC; - /* Configure PFx pins in Alternate function mode */ - GPIOF->MODER = 0xAA800AAA; - /* Configure PFx pins speed to 50 MHz */ - GPIOF->OSPEEDR = 0xAA800AAA; - /* Configure PFx pins Output type to push-pull */ - GPIOF->OTYPER = 0x00000000; - /* No pull-up, pull-down for PFx pins */ - GPIOF->PUPDR = 0x00000000; - /* Connect PGx pins to FMC Alternate function */ - GPIOG->AFR[0] = 0xCCCCCCCC; - GPIOG->AFR[1] = 0xCCCCCCCC; - /* Configure PGx pins in Alternate function mode */ - GPIOG->MODER = 0xAAAAAAAA; - /* Configure PGx pins speed to 50 MHz */ - GPIOG->OSPEEDR = 0xAAAAAAAA; - /* Configure PGx pins Output type to push-pull */ - GPIOG->OTYPER = 0x00000000; - /* No pull-up, pull-down for PGx pins */ - GPIOG->PUPDR = 0x00000000; -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\ - || defined(STM32F469xx) || defined(STM32F479xx) - /* Connect PHx pins to FMC Alternate function */ - GPIOH->AFR[0] = 0x00C0CC00; - GPIOH->AFR[1] = 0xCCCCCCCC; - /* Configure PHx pins in Alternate function mode */ - GPIOH->MODER = 0xAAAA08A0; - /* Configure PHx pins speed to 50 MHz */ - GPIOH->OSPEEDR = 0xAAAA08A0; - /* Configure PHx pins Output type to push-pull */ - GPIOH->OTYPER = 0x00000000; - /* No pull-up, pull-down for PHx pins */ - GPIOH->PUPDR = 0x00000000; - /* Connect PIx pins to FMC Alternate function */ - GPIOI->AFR[0] = 0xCCCCCCCC; - GPIOI->AFR[1] = 0x00000CC0; - /* Configure PIx pins in Alternate function mode */ - GPIOI->MODER = 0x0028AAAA; - /* Configure PIx pins speed to 50 MHz */ - GPIOI->OSPEEDR = 0x0028AAAA; - /* Configure PIx pins Output type to push-pull */ - GPIOI->OTYPER = 0x00000000; - /* No pull-up, pull-down for PIx pins */ - GPIOI->PUPDR = 0x00000000; -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - /*-- FMC Configuration -------------------------------------------------------*/ - /* Enable the FMC interface clock */ - RCC->AHB3ENR |= 0x00000001; - /* Delay after an RCC peripheral clock enabling */ - tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN); - /* Configure and enable SDRAM bank1 */ -#if defined(STM32F446xx) - FMC_Bank5_6->SDCR[0] = 0x00001954; -#else - FMC_Bank5_6->SDCR[0] = 0x000019E4; -#endif /* STM32F446xx */ - FMC_Bank5_6->SDTR[0] = 0x01115351; - /* SDRAM initialization sequence */ - /* Clock enable command */ - FMC_Bank5_6->SDCMR = 0x00000011; - tmpreg = FMC_Bank5_6->SDSR & 0x00000020; - - while ((tmpreg != 0) && (timeout-- > 0)) - { - tmpreg = FMC_Bank5_6->SDSR & 0x00000020; - } - - /* Delay */ - for (index = 0; index < 1000; index++); - - /* PALL command */ - FMC_Bank5_6->SDCMR = 0x00000012; - timeout = 0xFFFF; - - while ((tmpreg != 0) && (timeout-- > 0)) - { - tmpreg = FMC_Bank5_6->SDSR & 0x00000020; - } - - /* Auto refresh command */ -#if defined(STM32F446xx) - FMC_Bank5_6->SDCMR = 0x000000F3; -#else - FMC_Bank5_6->SDCMR = 0x00000073; -#endif /* STM32F446xx */ - timeout = 0xFFFF; - - while ((tmpreg != 0) && (timeout-- > 0)) - { - tmpreg = FMC_Bank5_6->SDSR & 0x00000020; - } - - /* MRD register program */ -#if defined(STM32F446xx) - FMC_Bank5_6->SDCMR = 0x00044014; -#else - FMC_Bank5_6->SDCMR = 0x00046014; -#endif /* STM32F446xx */ - timeout = 0xFFFF; - - while ((tmpreg != 0) && (timeout-- > 0)) - { - tmpreg = FMC_Bank5_6->SDSR & 0x00000020; - } - - /* Set refresh count */ - tmpreg = FMC_Bank5_6->SDRTR; -#if defined(STM32F446xx) - FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C << 1)); -#else - FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C << 1)); -#endif /* STM32F446xx */ - /* Disable write protection */ - tmpreg = FMC_Bank5_6->SDCR[0]; - FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF); -#endif /* DATA_IN_ExtSDRAM */ -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */ -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\ - || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\ - || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) -#if defined(DATA_IN_ExtSRAM) - /*-- GPIOs Configuration -----------------------------------------------------*/ - /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */ - RCC->AHB1ENR |= 0x00000078; - /* Delay after an RCC peripheral clock enabling */ - tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN); - /* Connect PDx pins to FMC Alternate function */ - GPIOD->AFR[0] = 0x00CCC0CC; - GPIOD->AFR[1] = 0xCCCCCCCC; - /* Configure PDx pins in Alternate function mode */ - GPIOD->MODER = 0xAAAA0A8A; - /* Configure PDx pins speed to 100 MHz */ - GPIOD->OSPEEDR = 0xFFFF0FCF; - /* Configure PDx pins Output type to push-pull */ - GPIOD->OTYPER = 0x00000000; - /* No pull-up, pull-down for PDx pins */ - GPIOD->PUPDR = 0x00000000; - /* Connect PEx pins to FMC Alternate function */ - GPIOE->AFR[0] = 0xC00CC0CC; - GPIOE->AFR[1] = 0xCCCCCCCC; - /* Configure PEx pins in Alternate function mode */ - GPIOE->MODER = 0xAAAA828A; - /* Configure PEx pins speed to 100 MHz */ - GPIOE->OSPEEDR = 0xFFFFC3CF; - /* Configure PEx pins Output type to push-pull */ - GPIOE->OTYPER = 0x00000000; - /* No pull-up, pull-down for PEx pins */ - GPIOE->PUPDR = 0x00000000; - /* Connect PFx pins to FMC Alternate function */ - GPIOF->AFR[0] = 0x00CCCCCC; - GPIOF->AFR[1] = 0xCCCC0000; - /* Configure PFx pins in Alternate function mode */ - GPIOF->MODER = 0xAA000AAA; - /* Configure PFx pins speed to 100 MHz */ - GPIOF->OSPEEDR = 0xFF000FFF; - /* Configure PFx pins Output type to push-pull */ - GPIOF->OTYPER = 0x00000000; - /* No pull-up, pull-down for PFx pins */ - GPIOF->PUPDR = 0x00000000; - /* Connect PGx pins to FMC Alternate function */ - GPIOG->AFR[0] = 0x00CCCCCC; - GPIOG->AFR[1] = 0x000000C0; - /* Configure PGx pins in Alternate function mode */ - GPIOG->MODER = 0x00085AAA; - /* Configure PGx pins speed to 100 MHz */ - GPIOG->OSPEEDR = 0x000CAFFF; - /* Configure PGx pins Output type to push-pull */ - GPIOG->OTYPER = 0x00000000; - /* No pull-up, pull-down for PGx pins */ - GPIOG->PUPDR = 0x00000000; - /*-- FMC/FSMC Configuration --------------------------------------------------*/ - /* Enable the FMC/FSMC interface clock */ - RCC->AHB3ENR |= 0x00000001; -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) - /* Delay after an RCC peripheral clock enabling */ - tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN); - /* Configure and enable Bank1_SRAM2 */ - FMC_Bank1->BTCR[2] = 0x00001011; - FMC_Bank1->BTCR[3] = 0x00000201; - FMC_Bank1E->BWTR[2] = 0x0fffffff; -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */ -#if defined(STM32F469xx) || defined(STM32F479xx) - /* Delay after an RCC peripheral clock enabling */ - tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN); - /* Configure and enable Bank1_SRAM2 */ - FMC_Bank1->BTCR[2] = 0x00001091; - FMC_Bank1->BTCR[3] = 0x00110212; - FMC_Bank1E->BWTR[2] = 0x0fffffff; -#endif /* STM32F469xx || STM32F479xx */ -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\ - || defined(STM32F412Zx) || defined(STM32F412Vx) - /* Delay after an RCC peripheral clock enabling */ - tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN); - /* Configure and enable Bank1_SRAM2 */ - FSMC_Bank1->BTCR[2] = 0x00001011; - FSMC_Bank1->BTCR[3] = 0x00000201; - FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF; -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */ -#endif /* DATA_IN_ExtSRAM */ -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\ - STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */ - (void)(tmp); -} -#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */ -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/CMSIS/Include/arm_common_tables.h b/EpsilonLights/Drivers/CMSIS/Include/arm_common_tables.h deleted file mode 100644 index 8742a569..00000000 --- a/EpsilonLights/Drivers/CMSIS/Include/arm_common_tables.h +++ /dev/null @@ -1,136 +0,0 @@ -/* ---------------------------------------------------------------------- -* Copyright (C) 2010-2014 ARM Limited. All rights reserved. -* -* $Date: 19. October 2015 -* $Revision: V.1.4.5 a -* -* Project: CMSIS DSP Library -* Title: arm_common_tables.h -* -* Description: This file has extern declaration for common tables like Bitreverse, reciprocal etc which are used across different functions -* -* Target Processor: Cortex-M4/Cortex-M3 -* -* Redistribution and use in source and binary forms, with or without -* modification, are permitted provided that the following conditions -* are met: -* - Redistributions of source code must retain the above copyright -* notice, this list of conditions and the following disclaimer. -* - Redistributions in binary form must reproduce the above copyright -* notice, this list of conditions and the following disclaimer in -* the documentation and/or other materials provided with the -* distribution. -* - Neither the name of ARM LIMITED nor the names of its contributors -* may be used to endorse or promote products derived from this -* software without specific prior written permission. -* -* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS -* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT -* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS -* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE -* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, -* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, -* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; -* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER -* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT -* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN -* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE -* POSSIBILITY OF SUCH DAMAGE. -* -------------------------------------------------------------------- */ - -#ifndef _ARM_COMMON_TABLES_H -#define _ARM_COMMON_TABLES_H - -#include "arm_math.h" - -extern const uint16_t armBitRevTable[1024]; -extern const q15_t armRecipTableQ15[64]; -extern const q31_t armRecipTableQ31[64]; -/* extern const q31_t realCoefAQ31[1024]; */ -/* extern const q31_t realCoefBQ31[1024]; */ -extern const float32_t twiddleCoef_16[32]; -extern const float32_t twiddleCoef_32[64]; -extern const float32_t twiddleCoef_64[128]; -extern const float32_t twiddleCoef_128[256]; -extern const float32_t twiddleCoef_256[512]; -extern const float32_t twiddleCoef_512[1024]; -extern const float32_t twiddleCoef_1024[2048]; -extern const float32_t twiddleCoef_2048[4096]; -extern const float32_t twiddleCoef_4096[8192]; -#define twiddleCoef twiddleCoef_4096 -extern const q31_t twiddleCoef_16_q31[24]; -extern const q31_t twiddleCoef_32_q31[48]; -extern const q31_t twiddleCoef_64_q31[96]; -extern const q31_t twiddleCoef_128_q31[192]; -extern const q31_t twiddleCoef_256_q31[384]; -extern const q31_t twiddleCoef_512_q31[768]; -extern const q31_t twiddleCoef_1024_q31[1536]; -extern const q31_t twiddleCoef_2048_q31[3072]; -extern const q31_t twiddleCoef_4096_q31[6144]; -extern const q15_t twiddleCoef_16_q15[24]; -extern const q15_t twiddleCoef_32_q15[48]; -extern const q15_t twiddleCoef_64_q15[96]; -extern const q15_t twiddleCoef_128_q15[192]; -extern const q15_t twiddleCoef_256_q15[384]; -extern const q15_t twiddleCoef_512_q15[768]; -extern const q15_t twiddleCoef_1024_q15[1536]; -extern const q15_t twiddleCoef_2048_q15[3072]; -extern const q15_t twiddleCoef_4096_q15[6144]; -extern const float32_t twiddleCoef_rfft_32[32]; -extern const float32_t twiddleCoef_rfft_64[64]; -extern const float32_t twiddleCoef_rfft_128[128]; -extern const float32_t twiddleCoef_rfft_256[256]; -extern const float32_t twiddleCoef_rfft_512[512]; -extern const float32_t twiddleCoef_rfft_1024[1024]; -extern const float32_t twiddleCoef_rfft_2048[2048]; -extern const float32_t twiddleCoef_rfft_4096[4096]; - - -/* floating-point bit reversal tables */ -#define ARMBITREVINDEXTABLE__16_TABLE_LENGTH ((uint16_t)20 ) -#define ARMBITREVINDEXTABLE__32_TABLE_LENGTH ((uint16_t)48 ) -#define ARMBITREVINDEXTABLE__64_TABLE_LENGTH ((uint16_t)56 ) -#define ARMBITREVINDEXTABLE_128_TABLE_LENGTH ((uint16_t)208 ) -#define ARMBITREVINDEXTABLE_256_TABLE_LENGTH ((uint16_t)440 ) -#define ARMBITREVINDEXTABLE_512_TABLE_LENGTH ((uint16_t)448 ) -#define ARMBITREVINDEXTABLE1024_TABLE_LENGTH ((uint16_t)1800) -#define ARMBITREVINDEXTABLE2048_TABLE_LENGTH ((uint16_t)3808) -#define ARMBITREVINDEXTABLE4096_TABLE_LENGTH ((uint16_t)4032) - -extern const uint16_t armBitRevIndexTable16[ARMBITREVINDEXTABLE__16_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable32[ARMBITREVINDEXTABLE__32_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable64[ARMBITREVINDEXTABLE__64_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable128[ARMBITREVINDEXTABLE_128_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable256[ARMBITREVINDEXTABLE_256_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable512[ARMBITREVINDEXTABLE_512_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable1024[ARMBITREVINDEXTABLE1024_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable2048[ARMBITREVINDEXTABLE2048_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable4096[ARMBITREVINDEXTABLE4096_TABLE_LENGTH]; - -/* fixed-point bit reversal tables */ -#define ARMBITREVINDEXTABLE_FIXED___16_TABLE_LENGTH ((uint16_t)12 ) -#define ARMBITREVINDEXTABLE_FIXED___32_TABLE_LENGTH ((uint16_t)24 ) -#define ARMBITREVINDEXTABLE_FIXED___64_TABLE_LENGTH ((uint16_t)56 ) -#define ARMBITREVINDEXTABLE_FIXED__128_TABLE_LENGTH ((uint16_t)112 ) -#define ARMBITREVINDEXTABLE_FIXED__256_TABLE_LENGTH ((uint16_t)240 ) -#define ARMBITREVINDEXTABLE_FIXED__512_TABLE_LENGTH ((uint16_t)480 ) -#define ARMBITREVINDEXTABLE_FIXED_1024_TABLE_LENGTH ((uint16_t)992 ) -#define ARMBITREVINDEXTABLE_FIXED_2048_TABLE_LENGTH ((uint16_t)1984) -#define ARMBITREVINDEXTABLE_FIXED_4096_TABLE_LENGTH ((uint16_t)4032) - -extern const uint16_t armBitRevIndexTable_fixed_16[ARMBITREVINDEXTABLE_FIXED___16_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable_fixed_32[ARMBITREVINDEXTABLE_FIXED___32_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable_fixed_64[ARMBITREVINDEXTABLE_FIXED___64_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable_fixed_128[ARMBITREVINDEXTABLE_FIXED__128_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable_fixed_256[ARMBITREVINDEXTABLE_FIXED__256_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable_fixed_512[ARMBITREVINDEXTABLE_FIXED__512_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable_fixed_1024[ARMBITREVINDEXTABLE_FIXED_1024_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable_fixed_2048[ARMBITREVINDEXTABLE_FIXED_2048_TABLE_LENGTH]; -extern const uint16_t armBitRevIndexTable_fixed_4096[ARMBITREVINDEXTABLE_FIXED_4096_TABLE_LENGTH]; - -/* Tables for Fast Math Sine and Cosine */ -extern const float32_t sinTable_f32[FAST_MATH_TABLE_SIZE + 1]; -extern const q31_t sinTable_q31[FAST_MATH_TABLE_SIZE + 1]; -extern const q15_t sinTable_q15[FAST_MATH_TABLE_SIZE + 1]; - -#endif /* ARM_COMMON_TABLES_H */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/arm_const_structs.h b/EpsilonLights/Drivers/CMSIS/Include/arm_const_structs.h deleted file mode 100644 index 8b1005f2..00000000 --- a/EpsilonLights/Drivers/CMSIS/Include/arm_const_structs.h +++ /dev/null @@ -1,79 +0,0 @@ -/* ---------------------------------------------------------------------- -* Copyright (C) 2010-2014 ARM Limited. All rights reserved. -* -* $Date: 19. March 2015 -* $Revision: V.1.4.5 -* -* Project: CMSIS DSP Library -* Title: arm_const_structs.h -* -* Description: This file has constant structs that are initialized for -* user convenience. For example, some can be given as -* arguments to the arm_cfft_f32() function. -* -* Target Processor: Cortex-M4/Cortex-M3 -* -* Redistribution and use in source and binary forms, with or without -* modification, are permitted provided that the following conditions -* are met: -* - Redistributions of source code must retain the above copyright -* notice, this list of conditions and the following disclaimer. -* - Redistributions in binary form must reproduce the above copyright -* notice, this list of conditions and the following disclaimer in -* the documentation and/or other materials provided with the -* distribution. -* - Neither the name of ARM LIMITED nor the names of its contributors -* may be used to endorse or promote products derived from this -* software without specific prior written permission. -* -* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS -* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT -* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS -* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE -* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, -* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, -* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; -* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER -* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT -* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN -* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE -* POSSIBILITY OF SUCH DAMAGE. -* -------------------------------------------------------------------- */ - -#ifndef _ARM_CONST_STRUCTS_H -#define _ARM_CONST_STRUCTS_H - -#include "arm_math.h" -#include "arm_common_tables.h" - -extern const arm_cfft_instance_f32 arm_cfft_sR_f32_len16; -extern const arm_cfft_instance_f32 arm_cfft_sR_f32_len32; -extern const arm_cfft_instance_f32 arm_cfft_sR_f32_len64; -extern const arm_cfft_instance_f32 arm_cfft_sR_f32_len128; -extern const arm_cfft_instance_f32 arm_cfft_sR_f32_len256; -extern const arm_cfft_instance_f32 arm_cfft_sR_f32_len512; -extern const arm_cfft_instance_f32 arm_cfft_sR_f32_len1024; -extern const arm_cfft_instance_f32 arm_cfft_sR_f32_len2048; -extern const arm_cfft_instance_f32 arm_cfft_sR_f32_len4096; - -extern const arm_cfft_instance_q31 arm_cfft_sR_q31_len16; -extern const arm_cfft_instance_q31 arm_cfft_sR_q31_len32; -extern const arm_cfft_instance_q31 arm_cfft_sR_q31_len64; -extern const arm_cfft_instance_q31 arm_cfft_sR_q31_len128; -extern const arm_cfft_instance_q31 arm_cfft_sR_q31_len256; -extern const arm_cfft_instance_q31 arm_cfft_sR_q31_len512; -extern const arm_cfft_instance_q31 arm_cfft_sR_q31_len1024; -extern const arm_cfft_instance_q31 arm_cfft_sR_q31_len2048; -extern const arm_cfft_instance_q31 arm_cfft_sR_q31_len4096; - -extern const arm_cfft_instance_q15 arm_cfft_sR_q15_len16; -extern const arm_cfft_instance_q15 arm_cfft_sR_q15_len32; -extern const arm_cfft_instance_q15 arm_cfft_sR_q15_len64; -extern const arm_cfft_instance_q15 arm_cfft_sR_q15_len128; -extern const arm_cfft_instance_q15 arm_cfft_sR_q15_len256; -extern const arm_cfft_instance_q15 arm_cfft_sR_q15_len512; -extern const arm_cfft_instance_q15 arm_cfft_sR_q15_len1024; -extern const arm_cfft_instance_q15 arm_cfft_sR_q15_len2048; -extern const arm_cfft_instance_q15 arm_cfft_sR_q15_len4096; - -#endif diff --git a/EpsilonLights/Drivers/CMSIS/Include/arm_math.h b/EpsilonLights/Drivers/CMSIS/Include/arm_math.h deleted file mode 100644 index 9c296277..00000000 --- a/EpsilonLights/Drivers/CMSIS/Include/arm_math.h +++ /dev/null @@ -1,7008 +0,0 @@ -/* ---------------------------------------------------------------------- -* Copyright (C) 2010-2015 ARM Limited. All rights reserved. -* -* $Date: 20. October 2015 -* $Revision: V1.4.5 b -* -* Project: CMSIS DSP Library -* Title: arm_math.h -* -* Description: Public header file for CMSIS DSP Library -* -* Target Processor: Cortex-M7/Cortex-M4/Cortex-M3/Cortex-M0 -* -* Redistribution and use in source and binary forms, with or without -* modification, are permitted provided that the following conditions -* are met: -* - Redistributions of source code must retain the above copyright -* notice, this list of conditions and the following disclaimer. -* - Redistributions in binary form must reproduce the above copyright -* notice, this list of conditions and the following disclaimer in -* the documentation and/or other materials provided with the -* distribution. -* - Neither the name of ARM LIMITED nor the names of its contributors -* may be used to endorse or promote products derived from this -* software without specific prior written permission. -* -* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS -* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT -* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS -* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE -* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, -* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, -* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; -* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER -* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT -* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN -* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE -* POSSIBILITY OF SUCH DAMAGE. - * -------------------------------------------------------------------- */ - -/** - \mainpage CMSIS DSP Software Library - * - * Introduction - * ------------ - * - * This user manual describes the CMSIS DSP software library, - * a suite of common signal processing functions for use on Cortex-M processor based devices. - * - * The library is divided into a number of functions each covering a specific category: - * - Basic math functions - * - Fast math functions - * - Complex math functions - * - Filters - * - Matrix functions - * - Transforms - * - Motor control functions - * - Statistical functions - * - Support functions - * - Interpolation functions - * - * The library has separate functions for operating on 8-bit integers, 16-bit integers, - * 32-bit integer and 32-bit floating-point values. - * - * Using the Library - * ------------ - * - * The library installer contains prebuilt versions of the libraries in the Lib folder. - * - arm_cortexM7lfdp_math.lib (Little endian and Double Precision Floating Point Unit on Cortex-M7) - * - arm_cortexM7bfdp_math.lib (Big endian and Double Precision Floating Point Unit on Cortex-M7) - * - arm_cortexM7lfsp_math.lib (Little endian and Single Precision Floating Point Unit on Cortex-M7) - * - arm_cortexM7bfsp_math.lib (Big endian and Single Precision Floating Point Unit on Cortex-M7) - * - arm_cortexM7l_math.lib (Little endian on Cortex-M7) - * - arm_cortexM7b_math.lib (Big endian on Cortex-M7) - * - arm_cortexM4lf_math.lib (Little endian and Floating Point Unit on Cortex-M4) - * - arm_cortexM4bf_math.lib (Big endian and Floating Point Unit on Cortex-M4) - * - arm_cortexM4l_math.lib (Little endian on Cortex-M4) - * - arm_cortexM4b_math.lib (Big endian on Cortex-M4) - * - arm_cortexM3l_math.lib (Little endian on Cortex-M3) - * - arm_cortexM3b_math.lib (Big endian on Cortex-M3) - * - arm_cortexM0l_math.lib (Little endian on Cortex-M0 / CortexM0+) - * - arm_cortexM0b_math.lib (Big endian on Cortex-M0 / CortexM0+) - * - * The library functions are declared in the public file arm_math.h which is placed in the Include folder. - * Simply include this file and link the appropriate library in the application and begin calling the library functions. The Library supports single - * public header file arm_math.h for Cortex-M7/M4/M3/M0/M0+ with little endian and big endian. Same header file will be used for floating point unit(FPU) variants. - * Define the appropriate pre processor MACRO ARM_MATH_CM7 or ARM_MATH_CM4 or ARM_MATH_CM3 or - * ARM_MATH_CM0 or ARM_MATH_CM0PLUS depending on the target processor in the application. - * - * Examples - * -------- - * - * The library ships with a number of examples which demonstrate how to use the library functions. - * - * Toolchain Support - * ------------ - * - * The library has been developed and tested with MDK-ARM version 5.14.0.0 - * The library is being tested in GCC and IAR toolchains and updates on this activity will be made available shortly. - * - * Building the Library - * ------------ - * - * The library installer contains a project file to re build libraries on MDK-ARM Tool chain in the CMSIS\\DSP_Lib\\Source\\ARM folder. - * - arm_cortexM_math.uvprojx - * - * - * The libraries can be built by opening the arm_cortexM_math.uvprojx project in MDK-ARM, selecting a specific target, and defining the optional pre processor MACROs detailed above. - * - * Pre-processor Macros - * ------------ - * - * Each library project have differant pre-processor macros. - * - * - UNALIGNED_SUPPORT_DISABLE: - * - * Define macro UNALIGNED_SUPPORT_DISABLE, If the silicon does not support unaligned memory access - * - * - ARM_MATH_BIG_ENDIAN: - * - * Define macro ARM_MATH_BIG_ENDIAN to build the library for big endian targets. By default library builds for little endian targets. - * - * - ARM_MATH_MATRIX_CHECK: - * - * Define macro ARM_MATH_MATRIX_CHECK for checking on the input and output sizes of matrices - * - * - ARM_MATH_ROUNDING: - * - * Define macro ARM_MATH_ROUNDING for rounding on support functions - * - * - ARM_MATH_CMx: - * - * Define macro ARM_MATH_CM4 for building the library on Cortex-M4 target, ARM_MATH_CM3 for building library on Cortex-M3 target - * and ARM_MATH_CM0 for building library on Cortex-M0 target, ARM_MATH_CM0PLUS for building library on Cortex-M0+ target, and - * ARM_MATH_CM7 for building the library on cortex-M7. - * - * - __FPU_PRESENT: - * - * Initialize macro __FPU_PRESENT = 1 when building on FPU supported Targets. Enable this macro for M4bf and M4lf libraries - * - *
- * CMSIS-DSP in ARM::CMSIS Pack - * ----------------------------- - * - * The following files relevant to CMSIS-DSP are present in the ARM::CMSIS Pack directories: - * |File/Folder |Content | - * |------------------------------|------------------------------------------------------------------------| - * |\b CMSIS\\Documentation\\DSP | This documentation | - * |\b CMSIS\\DSP_Lib | Software license agreement (license.txt) | - * |\b CMSIS\\DSP_Lib\\Examples | Example projects demonstrating the usage of the library functions | - * |\b CMSIS\\DSP_Lib\\Source | Source files for rebuilding the library | - * - *
- * Revision History of CMSIS-DSP - * ------------ - * Please refer to \ref ChangeLog_pg. - * - * Copyright Notice - * ------------ - * - * Copyright (C) 2010-2015 ARM Limited. All rights reserved. - */ - - -/** - * @defgroup groupMath Basic Math Functions - */ - -/** - * @defgroup groupFastMath Fast Math Functions - * This set of functions provides a fast approximation to sine, cosine, and square root. - * As compared to most of the other functions in the CMSIS math library, the fast math functions - * operate on individual values and not arrays. - * There are separate functions for Q15, Q31, and floating-point data. - * - */ - -/** - * @defgroup groupCmplxMath Complex Math Functions - * This set of functions operates on complex data vectors. - * The data in the complex arrays is stored in an interleaved fashion - * (real, imag, real, imag, ...). - * In the API functions, the number of samples in a complex array refers - * to the number of complex values; the array contains twice this number of - * real values. - */ - -/** - * @defgroup groupFilters Filtering Functions - */ - -/** - * @defgroup groupMatrix Matrix Functions - * - * This set of functions provides basic matrix math operations. - * The functions operate on matrix data structures. For example, - * the type - * definition for the floating-point matrix structure is shown - * below: - * 
- *     typedef struct
- *     {
- *       uint16_t numRows;     // number of rows of the matrix.
- *       uint16_t numCols;     // number of columns of the matrix.
- *       float32_t *pData;     // points to the data of the matrix.
- *     } arm_matrix_instance_f32;
- *
- * There are similar definitions for Q15 and Q31 data types. - * - * The structure specifies the size of the matrix and then points to - * an array of data. The array is of size numRows X numCols - * and the values are arranged in row order. That is, the - * matrix element (i, j) is stored at: - * 
- *     pData[i*numCols + j]
- *
- * - * \par Init Functions - * There is an associated initialization function for each type of matrix - * data structure. - * The initialization function sets the values of the internal structure fields. - * Refer to the function arm_mat_init_f32(), arm_mat_init_q31() - * and arm_mat_init_q15() for floating-point, Q31 and Q15 types, respectively. - * - * \par - * Use of the initialization function is optional. However, if initialization function is used - * then the instance structure cannot be placed into a const data section. - * To place the instance structure in a const data - * section, manually initialize the data structure. For example: - * 
- * arm_matrix_instance_f32 S = {nRows, nColumns, pData};
- * arm_matrix_instance_q31 S = {nRows, nColumns, pData};
- * arm_matrix_instance_q15 S = {nRows, nColumns, pData};
- *
- * where nRows specifies the number of rows, nColumns - * specifies the number of columns, and pData points to the - * data array. - * - * \par Size Checking - * By default all of the matrix functions perform size checking on the input and - * output matrices. For example, the matrix addition function verifies that the - * two input matrices and the output matrix all have the same number of rows and - * columns. If the size check fails the functions return: - * 
- *     ARM_MATH_SIZE_MISMATCH
- *
- * Otherwise the functions return - * 
- *     ARM_MATH_SUCCESS
- *
- * There is some overhead associated with this matrix size checking. - * The matrix size checking is enabled via the \#define - * 
- *     ARM_MATH_MATRIX_CHECK
- *
- * within the library project settings. By default this macro is defined - * and size checking is enabled. By changing the project settings and - * undefining this macro size checking is eliminated and the functions - * run a bit faster. With size checking disabled the functions always - * return ARM_MATH_SUCCESS. - */ - -/** - * @defgroup groupTransforms Transform Functions - */ - -/** - * @defgroup groupController Controller Functions - */ - -/** - * @defgroup groupStats Statistics Functions - */ -/** - * @defgroup groupSupport Support Functions - */ - -/** - * @defgroup groupInterpolation Interpolation Functions - * These functions perform 1- and 2-dimensional interpolation of data. - * Linear interpolation is used for 1-dimensional data and - * bilinear interpolation is used for 2-dimensional data. - */ - -/** - * @defgroup groupExamples Examples - */ -#ifndef _ARM_MATH_H -#define _ARM_MATH_H - -/* ignore some GCC warnings */ -#if defined ( __GNUC__ ) -#pragma GCC diagnostic push -#pragma GCC diagnostic ignored "-Wsign-conversion" -#pragma GCC diagnostic ignored "-Wconversion" -#pragma GCC diagnostic ignored "-Wunused-parameter" -#endif - -#define __CMSIS_GENERIC /* disable NVIC and Systick functions */ - -#if defined(ARM_MATH_CM7) -#include "core_cm7.h" -#elif defined (ARM_MATH_CM4) -#include "core_cm4.h" -#elif defined (ARM_MATH_CM3) -#include "core_cm3.h" -#elif defined (ARM_MATH_CM0) -#include "core_cm0.h" -#define ARM_MATH_CM0_FAMILY -#elif defined (ARM_MATH_CM0PLUS) -#include "core_cm0plus.h" -#define ARM_MATH_CM0_FAMILY -#else -#error "Define according the used Cortex core ARM_MATH_CM7, ARM_MATH_CM4, ARM_MATH_CM3, ARM_MATH_CM0PLUS or ARM_MATH_CM0" -#endif - -#undef __CMSIS_GENERIC /* enable NVIC and Systick functions */ -#include "string.h" -#include "math.h" -#ifdef __cplusplus -extern "C" -{ -#endif - - -/** - * @brief Macros required for reciprocal calculation in Normalized LMS - */ - -#define DELTA_Q31 (0x100) -#define DELTA_Q15 0x5 -#define INDEX_MASK 0x0000003F -#ifndef PI -#define PI 3.14159265358979f -#endif - -/** - * @brief Macros required for SINE and COSINE Fast math approximations - */ - -#define FAST_MATH_TABLE_SIZE 512 -#define FAST_MATH_Q31_SHIFT (32 - 10) -#define FAST_MATH_Q15_SHIFT (16 - 10) -#define CONTROLLER_Q31_SHIFT (32 - 9) -#define TABLE_SIZE 256 -#define TABLE_SPACING_Q31 0x400000 -#define TABLE_SPACING_Q15 0x80 - -/** - * @brief Macros required for SINE and COSINE Controller functions - */ -/* 1.31(q31) Fixed value of 2/360 */ -/* -1 to +1 is divided into 360 values so total spacing is (2/360) */ -#define INPUT_SPACING 0xB60B61 - -/** - * @brief Macro for Unaligned Support - */ -#ifndef UNALIGNED_SUPPORT_DISABLE -#define ALIGN4 -#else -#if defined (__GNUC__) -#define ALIGN4 __attribute__((aligned(4))) -#else -#define ALIGN4 __align(4) -#endif -#endif /* #ifndef UNALIGNED_SUPPORT_DISABLE */ - -/** - * @brief Error status returned by some functions in the library. - */ - -typedef enum -{ - ARM_MATH_SUCCESS = 0, /**< No error */ - ARM_MATH_ARGUMENT_ERROR = -1, /**< One or more arguments are incorrect */ - ARM_MATH_LENGTH_ERROR = -2, /**< Length of data buffer is incorrect */ - ARM_MATH_SIZE_MISMATCH = -3, /**< Size of matrices is not compatible with the operation. */ - ARM_MATH_NANINF = -4, /**< Not-a-number (NaN) or infinity is generated */ - ARM_MATH_SINGULAR = -5, /**< Generated by matrix inversion if the input matrix is singular and cannot be inverted. */ - ARM_MATH_TEST_FAILURE = -6 /**< Test Failed */ -} arm_status; - -/** - * @brief 8-bit fractional data type in 1.7 format. - */ -typedef int8_t q7_t; - -/** - * @brief 16-bit fractional data type in 1.15 format. - */ -typedef int16_t q15_t; - -/** - * @brief 32-bit fractional data type in 1.31 format. - */ -typedef int32_t q31_t; - -/** - * @brief 64-bit fractional data type in 1.63 format. - */ -typedef int64_t q63_t; - -/** - * @brief 32-bit floating-point type definition. - */ -typedef float float32_t; - -/** - * @brief 64-bit floating-point type definition. - */ -typedef double float64_t; - -/** - * @brief definition to read/write two 16 bit values. - */ -#if defined __CC_ARM -#define __SIMD32_TYPE int32_t __packed -#define CMSIS_UNUSED __attribute__((unused)) - -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) -#define __SIMD32_TYPE int32_t -#define CMSIS_UNUSED __attribute__((unused)) - -#elif defined __GNUC__ -#define __SIMD32_TYPE int32_t -#define CMSIS_UNUSED __attribute__((unused)) - -#elif defined __ICCARM__ -#define __SIMD32_TYPE int32_t __packed -#define CMSIS_UNUSED - -#elif defined __CSMC__ -#define __SIMD32_TYPE int32_t -#define CMSIS_UNUSED - -#elif defined __TASKING__ -#define __SIMD32_TYPE __unaligned int32_t -#define CMSIS_UNUSED - -#else -#error Unknown compiler -#endif - -#define __SIMD32(addr) (*(__SIMD32_TYPE **) & (addr)) -#define __SIMD32_CONST(addr) ((__SIMD32_TYPE *)(addr)) -#define _SIMD32_OFFSET(addr) (*(__SIMD32_TYPE *) (addr)) -#define __SIMD64(addr) (*(int64_t **) & (addr)) - -#if defined (ARM_MATH_CM3) || defined (ARM_MATH_CM0_FAMILY) -/** - * @brief definition to pack two 16 bit values. - */ -#define __PKHBT(ARG1, ARG2, ARG3) ( (((int32_t)(ARG1) << 0) & (int32_t)0x0000FFFF) | \ - (((int32_t)(ARG2) << ARG3) & (int32_t)0xFFFF0000) ) -#define __PKHTB(ARG1, ARG2, ARG3) ( (((int32_t)(ARG1) << 0) & (int32_t)0xFFFF0000) | \ - (((int32_t)(ARG2) >> ARG3) & (int32_t)0x0000FFFF) ) - -#endif - - -/** -* @brief definition to pack four 8 bit values. -*/ -#ifndef ARM_MATH_BIG_ENDIAN - -#define __PACKq7(v0,v1,v2,v3) ( (((int32_t)(v0) << 0) & (int32_t)0x000000FF) | \ - (((int32_t)(v1) << 8) & (int32_t)0x0000FF00) | \ - (((int32_t)(v2) << 16) & (int32_t)0x00FF0000) | \ - (((int32_t)(v3) << 24) & (int32_t)0xFF000000) ) -#else - -#define __PACKq7(v0,v1,v2,v3) ( (((int32_t)(v3) << 0) & (int32_t)0x000000FF) | \ - (((int32_t)(v2) << 8) & (int32_t)0x0000FF00) | \ - (((int32_t)(v1) << 16) & (int32_t)0x00FF0000) | \ - (((int32_t)(v0) << 24) & (int32_t)0xFF000000) ) - -#endif - - -/** - * @brief Clips Q63 to Q31 values. - */ -static __INLINE q31_t clip_q63_to_q31( - q63_t x) -{ - return ((q31_t) (x >> 32) != ((q31_t) x >> 31)) ? - ((0x7FFFFFFF ^ ((q31_t) (x >> 63)))) : (q31_t) x; -} - -/** - * @brief Clips Q63 to Q15 values. - */ -static __INLINE q15_t clip_q63_to_q15( - q63_t x) -{ - return ((q31_t) (x >> 32) != ((q31_t) x >> 31)) ? - ((0x7FFF ^ ((q15_t) (x >> 63)))) : (q15_t) (x >> 15); -} - -/** - * @brief Clips Q31 to Q7 values. - */ -static __INLINE q7_t clip_q31_to_q7( - q31_t x) -{ - return ((q31_t) (x >> 24) != ((q31_t) x >> 23)) ? - ((0x7F ^ ((q7_t) (x >> 31)))) : (q7_t) x; -} - -/** - * @brief Clips Q31 to Q15 values. - */ -static __INLINE q15_t clip_q31_to_q15( - q31_t x) -{ - return ((q31_t) (x >> 16) != ((q31_t) x >> 15)) ? - ((0x7FFF ^ ((q15_t) (x >> 31)))) : (q15_t) x; -} - -/** - * @brief Multiplies 32 X 64 and returns 32 bit result in 2.30 format. - */ - -static __INLINE q63_t mult32x64( - q63_t x, - q31_t y) -{ - return ((((q63_t) (x & 0x00000000FFFFFFFF) * y) >> 32) + - (((q63_t) (x >> 32) * y))); -} - -/* - #if defined (ARM_MATH_CM0_FAMILY) && defined ( __CC_ARM ) - #define __CLZ __clz - #endif - */ -/* note: function can be removed when all toolchain support __CLZ for Cortex-M0 */ -#if defined (ARM_MATH_CM0_FAMILY) && ((defined (__ICCARM__)) ) -static __INLINE uint32_t __CLZ( - q31_t data); - -static __INLINE uint32_t __CLZ( - q31_t data) -{ - uint32_t count = 0; - uint32_t mask = 0x80000000; - - while ((data & mask) == 0) - { - count += 1u; - mask = mask >> 1u; - } - - return (count); -} -#endif - -/** - * @brief Function to Calculates 1/in (reciprocal) value of Q31 Data type. - */ - -static __INLINE uint32_t arm_recip_q31( - q31_t in, - q31_t* dst, - q31_t* pRecipTable) -{ - q31_t out; - uint32_t tempVal; - uint32_t index, i; - uint32_t signBits; - - if (in > 0) - { - signBits = ((uint32_t) (__CLZ( in) - 1)); - } - else - { - signBits = ((uint32_t) (__CLZ(-in) - 1)); - } - - /* Convert input sample to 1.31 format */ - in = (in << signBits); - /* calculation of index for initial approximated Val */ - index = (uint32_t)(in >> 24); - index = (index & INDEX_MASK); - /* 1.31 with exp 1 */ - out = pRecipTable[index]; - - /* calculation of reciprocal value */ - /* running approximation for two iterations */ - for (i = 0u; i < 2u; i++) - { - tempVal = (uint32_t) (((q63_t) in * out) >> 31); - tempVal = 0x7FFFFFFFu - tempVal; - /* 1.31 with exp 1 */ - /* out = (q31_t) (((q63_t) out * tempVal) >> 30); */ - out = clip_q63_to_q31(((q63_t) out * tempVal) >> 30); - } - - /* write output */ - *dst = out; - /* return num of signbits of out = 1/in value */ - return (signBits + 1u); -} - - -/** - * @brief Function to Calculates 1/in (reciprocal) value of Q15 Data type. - */ -static __INLINE uint32_t arm_recip_q15( - q15_t in, - q15_t* dst, - q15_t* pRecipTable) -{ - q15_t out = 0; - uint32_t tempVal = 0; - uint32_t index = 0, i = 0; - uint32_t signBits = 0; - - if (in > 0) - { - signBits = ((uint32_t)(__CLZ( in) - 17)); - } - else - { - signBits = ((uint32_t)(__CLZ(-in) - 17)); - } - - /* Convert input sample to 1.15 format */ - in = (in << signBits); - /* calculation of index for initial approximated Val */ - index = (uint32_t)(in >> 8); - index = (index & INDEX_MASK); - /* 1.15 with exp 1 */ - out = pRecipTable[index]; - - /* calculation of reciprocal value */ - /* running approximation for two iterations */ - for (i = 0u; i < 2u; i++) - { - tempVal = (uint32_t) (((q31_t) in * out) >> 15); - tempVal = 0x7FFFu - tempVal; - /* 1.15 with exp 1 */ - out = (q15_t) (((q31_t) out * tempVal) >> 14); - /* out = clip_q31_to_q15(((q31_t) out * tempVal) >> 14); */ - } - - /* write output */ - *dst = out; - /* return num of signbits of out = 1/in value */ - return (signBits + 1); -} - - -/* - * @brief C custom defined intrinisic function for only M0 processors - */ -#if defined(ARM_MATH_CM0_FAMILY) -static __INLINE q31_t __SSAT( - q31_t x, - uint32_t y) -{ - int32_t posMax, negMin; - uint32_t i; - posMax = 1; - - for (i = 0; i < (y - 1); i++) - { - posMax = posMax * 2; - } - - if (x > 0) - { - posMax = (posMax - 1); - - if (x > posMax) - { - x = posMax; - } - } - else - { - negMin = -posMax; - - if (x < negMin) - { - x = negMin; - } - } - - return (x); -} -#endif /* end of ARM_MATH_CM0_FAMILY */ - - -/* - * @brief C custom defined intrinsic function for M3 and M0 processors - */ -#if defined (ARM_MATH_CM3) || defined (ARM_MATH_CM0_FAMILY) - -/* - * @brief C custom defined QADD8 for M3 and M0 processors - */ -static __INLINE uint32_t __QADD8( - uint32_t x, - uint32_t y) -{ - q31_t r, s, t, u; - r = __SSAT(((((q31_t)x << 24) >> 24) + (((q31_t)y << 24) >> 24)), 8) & (int32_t)0x000000FF; - s = __SSAT(((((q31_t)x << 16) >> 24) + (((q31_t)y << 16) >> 24)), 8) & (int32_t)0x000000FF; - t = __SSAT(((((q31_t)x << 8) >> 24) + (((q31_t)y << 8) >> 24)), 8) & (int32_t)0x000000FF; - u = __SSAT(((((q31_t)x ) >> 24) + (((q31_t)y ) >> 24)), 8) & (int32_t)0x000000FF; - return ((uint32_t)((u << 24) | (t << 16) | (s << 8) | (r ))); -} - - -/* - * @brief C custom defined QSUB8 for M3 and M0 processors - */ -static __INLINE uint32_t __QSUB8( - uint32_t x, - uint32_t y) -{ - q31_t r, s, t, u; - r = __SSAT(((((q31_t)x << 24) >> 24) - (((q31_t)y << 24) >> 24)), 8) & (int32_t)0x000000FF; - s = __SSAT(((((q31_t)x << 16) >> 24) - (((q31_t)y << 16) >> 24)), 8) & (int32_t)0x000000FF; - t = __SSAT(((((q31_t)x << 8) >> 24) - (((q31_t)y << 8) >> 24)), 8) & (int32_t)0x000000FF; - u = __SSAT(((((q31_t)x ) >> 24) - (((q31_t)y ) >> 24)), 8) & (int32_t)0x000000FF; - return ((uint32_t)((u << 24) | (t << 16) | (s << 8) | (r ))); -} - - -/* - * @brief C custom defined QADD16 for M3 and M0 processors - */ -static __INLINE uint32_t __QADD16( - uint32_t x, - uint32_t y) -{ - /* q31_t r, s; without initialisation 'arm_offset_q15 test' fails but 'intrinsic' tests pass! for armCC */ - q31_t r = 0, s = 0; - r = __SSAT(((((q31_t)x << 16) >> 16) + (((q31_t)y << 16) >> 16)), 16) & (int32_t)0x0000FFFF; - s = __SSAT(((((q31_t)x ) >> 16) + (((q31_t)y ) >> 16)), 16) & (int32_t)0x0000FFFF; - return ((uint32_t)((s << 16) | (r ))); -} - - -/* - * @brief C custom defined SHADD16 for M3 and M0 processors - */ -static __INLINE uint32_t __SHADD16( - uint32_t x, - uint32_t y) -{ - q31_t r, s; - r = (((((q31_t)x << 16) >> 16) + (((q31_t)y << 16) >> 16)) >> 1) & (int32_t)0x0000FFFF; - s = (((((q31_t)x ) >> 16) + (((q31_t)y ) >> 16)) >> 1) & (int32_t)0x0000FFFF; - return ((uint32_t)((s << 16) | (r ))); -} - - -/* - * @brief C custom defined QSUB16 for M3 and M0 processors - */ -static __INLINE uint32_t __QSUB16( - uint32_t x, - uint32_t y) -{ - q31_t r, s; - r = __SSAT(((((q31_t)x << 16) >> 16) - (((q31_t)y << 16) >> 16)), 16) & (int32_t)0x0000FFFF; - s = __SSAT(((((q31_t)x ) >> 16) - (((q31_t)y ) >> 16)), 16) & (int32_t)0x0000FFFF; - return ((uint32_t)((s << 16) | (r ))); -} - - -/* - * @brief C custom defined SHSUB16 for M3 and M0 processors - */ -static __INLINE uint32_t __SHSUB16( - uint32_t x, - uint32_t y) -{ - q31_t r, s; - r = (((((q31_t)x << 16) >> 16) - (((q31_t)y << 16) >> 16)) >> 1) & (int32_t)0x0000FFFF; - s = (((((q31_t)x ) >> 16) - (((q31_t)y ) >> 16)) >> 1) & (int32_t)0x0000FFFF; - return ((uint32_t)((s << 16) | (r ))); -} - - -/* - * @brief C custom defined QASX for M3 and M0 processors - */ -static __INLINE uint32_t __QASX( - uint32_t x, - uint32_t y) -{ - q31_t r, s; - r = __SSAT(((((q31_t)x << 16) >> 16) - (((q31_t)y ) >> 16)), 16) & (int32_t)0x0000FFFF; - s = __SSAT(((((q31_t)x ) >> 16) + (((q31_t)y << 16) >> 16)), 16) & (int32_t)0x0000FFFF; - return ((uint32_t)((s << 16) | (r ))); -} - - -/* - * @brief C custom defined SHASX for M3 and M0 processors - */ -static __INLINE uint32_t __SHASX( - uint32_t x, - uint32_t y) -{ - q31_t r, s; - r = (((((q31_t)x << 16) >> 16) - (((q31_t)y ) >> 16)) >> 1) & (int32_t)0x0000FFFF; - s = (((((q31_t)x ) >> 16) + (((q31_t)y << 16) >> 16)) >> 1) & (int32_t)0x0000FFFF; - return ((uint32_t)((s << 16) | (r ))); -} - - -/* - * @brief C custom defined QSAX for M3 and M0 processors - */ -static __INLINE uint32_t __QSAX( - uint32_t x, - uint32_t y) -{ - q31_t r, s; - r = __SSAT(((((q31_t)x << 16) >> 16) + (((q31_t)y ) >> 16)), 16) & (int32_t)0x0000FFFF; - s = __SSAT(((((q31_t)x ) >> 16) - (((q31_t)y << 16) >> 16)), 16) & (int32_t)0x0000FFFF; - return ((uint32_t)((s << 16) | (r ))); -} - - -/* - * @brief C custom defined SHSAX for M3 and M0 processors - */ -static __INLINE uint32_t __SHSAX( - uint32_t x, - uint32_t y) -{ - q31_t r, s; - r = (((((q31_t)x << 16) >> 16) + (((q31_t)y ) >> 16)) >> 1) & (int32_t)0x0000FFFF; - s = (((((q31_t)x ) >> 16) - (((q31_t)y << 16) >> 16)) >> 1) & (int32_t)0x0000FFFF; - return ((uint32_t)((s << 16) | (r ))); -} - - -/* - * @brief C custom defined SMUSDX for M3 and M0 processors - */ -static __INLINE uint32_t __SMUSDX( - uint32_t x, - uint32_t y) -{ - return ((uint32_t)(((((q31_t)x << 16) >> 16) * (((q31_t)y ) >> 16)) - - ((((q31_t)x ) >> 16) * (((q31_t)y << 16) >> 16)) )); -} - -/* - * @brief C custom defined SMUADX for M3 and M0 processors - */ -static __INLINE uint32_t __SMUADX( - uint32_t x, - uint32_t y) -{ - return ((uint32_t)(((((q31_t)x << 16) >> 16) * (((q31_t)y ) >> 16)) + - ((((q31_t)x ) >> 16) * (((q31_t)y << 16) >> 16)) )); -} - - -/* - * @brief C custom defined QADD for M3 and M0 processors - */ -static __INLINE int32_t __QADD( - int32_t x, - int32_t y) -{ - return ((int32_t)(clip_q63_to_q31((q63_t)x + (q31_t)y))); -} - - -/* - * @brief C custom defined QSUB for M3 and M0 processors - */ -static __INLINE int32_t __QSUB( - int32_t x, - int32_t y) -{ - return ((int32_t)(clip_q63_to_q31((q63_t)x - (q31_t)y))); -} - - -/* - * @brief C custom defined SMLAD for M3 and M0 processors - */ -static __INLINE uint32_t __SMLAD( - uint32_t x, - uint32_t y, - uint32_t sum) -{ - return ((uint32_t)(((((q31_t)x << 16) >> 16) * (((q31_t)y << 16) >> 16)) + - ((((q31_t)x ) >> 16) * (((q31_t)y ) >> 16)) + - ( ((q31_t)sum ) ) )); -} - - -/* - * @brief C custom defined SMLADX for M3 and M0 processors - */ -static __INLINE uint32_t __SMLADX( - uint32_t x, - uint32_t y, - uint32_t sum) -{ - return ((uint32_t)(((((q31_t)x << 16) >> 16) * (((q31_t)y ) >> 16)) + - ((((q31_t)x ) >> 16) * (((q31_t)y << 16) >> 16)) + - ( ((q31_t)sum ) ) )); -} - - -/* - * @brief C custom defined SMLSDX for M3 and M0 processors - */ -static __INLINE uint32_t __SMLSDX( - uint32_t x, - uint32_t y, - uint32_t sum) -{ - return ((uint32_t)(((((q31_t)x << 16) >> 16) * (((q31_t)y ) >> 16)) - - ((((q31_t)x ) >> 16) * (((q31_t)y << 16) >> 16)) + - ( ((q31_t)sum ) ) )); -} - - -/* - * @brief C custom defined SMLALD for M3 and M0 processors - */ -static __INLINE uint64_t __SMLALD( - uint32_t x, - uint32_t y, - uint64_t sum) -{ - /* return (sum + ((q15_t) (x >> 16) * (q15_t) (y >> 16)) + ((q15_t) x * (q15_t) y)); */ - return ((uint64_t)(((((q31_t)x << 16) >> 16) * (((q31_t)y << 16) >> 16)) + - ((((q31_t)x ) >> 16) * (((q31_t)y ) >> 16)) + - ( ((q63_t)sum ) ) )); -} - - -/* - * @brief C custom defined SMLALDX for M3 and M0 processors - */ -static __INLINE uint64_t __SMLALDX( - uint32_t x, - uint32_t y, - uint64_t sum) -{ - /* return (sum + ((q15_t) (x >> 16) * (q15_t) y)) + ((q15_t) x * (q15_t) (y >> 16)); */ - return ((uint64_t)(((((q31_t)x << 16) >> 16) * (((q31_t)y ) >> 16)) + - ((((q31_t)x ) >> 16) * (((q31_t)y << 16) >> 16)) + - ( ((q63_t)sum ) ) )); -} - - -/* - * @brief C custom defined SMUAD for M3 and M0 processors - */ -static __INLINE uint32_t __SMUAD( - uint32_t x, - uint32_t y) -{ - return ((uint32_t)(((((q31_t)x << 16) >> 16) * (((q31_t)y << 16) >> 16)) + - ((((q31_t)x ) >> 16) * (((q31_t)y ) >> 16)) )); -} - - -/* - * @brief C custom defined SMUSD for M3 and M0 processors - */ -static __INLINE uint32_t __SMUSD( - uint32_t x, - uint32_t y) -{ - return ((uint32_t)(((((q31_t)x << 16) >> 16) * (((q31_t)y << 16) >> 16)) - - ((((q31_t)x ) >> 16) * (((q31_t)y ) >> 16)) )); -} - - -/* - * @brief C custom defined SXTB16 for M3 and M0 processors - */ -static __INLINE uint32_t __SXTB16( - uint32_t x) -{ - return ((uint32_t)(((((q31_t)x << 24) >> 24) & (q31_t)0x0000FFFF) | - ((((q31_t)x << 8) >> 8) & (q31_t)0xFFFF0000) )); -} - -#endif /* defined (ARM_MATH_CM3) || defined (ARM_MATH_CM0_FAMILY) */ - - -/** - * @brief Instance structure for the Q7 FIR filter. - */ -typedef struct -{ - uint16_t numTaps; /**< number of filter coefficients in the filter. */ - q7_t* pState; /**< points to the state variable array. The array is of length numTaps+blockSize-1. */ - q7_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps.*/ -} arm_fir_instance_q7; - -/** - * @brief Instance structure for the Q15 FIR filter. - */ -typedef struct -{ - uint16_t numTaps; /**< number of filter coefficients in the filter. */ - q15_t* pState; /**< points to the state variable array. The array is of length numTaps+blockSize-1. */ - q15_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps.*/ -} arm_fir_instance_q15; - -/** - * @brief Instance structure for the Q31 FIR filter. - */ -typedef struct -{ - uint16_t numTaps; /**< number of filter coefficients in the filter. */ - q31_t* pState; /**< points to the state variable array. The array is of length numTaps+blockSize-1. */ - q31_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps. */ -} arm_fir_instance_q31; - -/** - * @brief Instance structure for the floating-point FIR filter. - */ -typedef struct -{ - uint16_t numTaps; /**< number of filter coefficients in the filter. */ - float32_t* pState; /**< points to the state variable array. The array is of length numTaps+blockSize-1. */ - float32_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps. */ -} arm_fir_instance_f32; - - -/** - * @brief Processing function for the Q7 FIR filter. - * @param[in] S points to an instance of the Q7 FIR filter structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of samples to process. - */ -void arm_fir_q7( - const arm_fir_instance_q7* S, - q7_t* pSrc, - q7_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the Q7 FIR filter. - * @param[in,out] S points to an instance of the Q7 FIR structure. - * @param[in] numTaps Number of filter coefficients in the filter. - * @param[in] pCoeffs points to the filter coefficients. - * @param[in] pState points to the state buffer. - * @param[in] blockSize number of samples that are processed. - */ -void arm_fir_init_q7( - arm_fir_instance_q7* S, - uint16_t numTaps, - q7_t* pCoeffs, - q7_t* pState, - uint32_t blockSize); - - -/** - * @brief Processing function for the Q15 FIR filter. - * @param[in] S points to an instance of the Q15 FIR structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of samples to process. - */ -void arm_fir_q15( - const arm_fir_instance_q15* S, - q15_t* pSrc, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Processing function for the fast Q15 FIR filter for Cortex-M3 and Cortex-M4. - * @param[in] S points to an instance of the Q15 FIR filter structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of samples to process. - */ -void arm_fir_fast_q15( - const arm_fir_instance_q15* S, - q15_t* pSrc, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the Q15 FIR filter. - * @param[in,out] S points to an instance of the Q15 FIR filter structure. - * @param[in] numTaps Number of filter coefficients in the filter. Must be even and greater than or equal to 4. - * @param[in] pCoeffs points to the filter coefficients. - * @param[in] pState points to the state buffer. - * @param[in] blockSize number of samples that are processed at a time. - * @return The function returns ARM_MATH_SUCCESS if initialization was successful or ARM_MATH_ARGUMENT_ERROR if - * numTaps is not a supported value. - */ -arm_status arm_fir_init_q15( - arm_fir_instance_q15* S, - uint16_t numTaps, - q15_t* pCoeffs, - q15_t* pState, - uint32_t blockSize); - - -/** - * @brief Processing function for the Q31 FIR filter. - * @param[in] S points to an instance of the Q31 FIR filter structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of samples to process. - */ -void arm_fir_q31( - const arm_fir_instance_q31* S, - q31_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Processing function for the fast Q31 FIR filter for Cortex-M3 and Cortex-M4. - * @param[in] S points to an instance of the Q31 FIR structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of samples to process. - */ -void arm_fir_fast_q31( - const arm_fir_instance_q31* S, - q31_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the Q31 FIR filter. - * @param[in,out] S points to an instance of the Q31 FIR structure. - * @param[in] numTaps Number of filter coefficients in the filter. - * @param[in] pCoeffs points to the filter coefficients. - * @param[in] pState points to the state buffer. - * @param[in] blockSize number of samples that are processed at a time. - */ -void arm_fir_init_q31( - arm_fir_instance_q31* S, - uint16_t numTaps, - q31_t* pCoeffs, - q31_t* pState, - uint32_t blockSize); - - -/** - * @brief Processing function for the floating-point FIR filter. - * @param[in] S points to an instance of the floating-point FIR structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of samples to process. - */ -void arm_fir_f32( - const arm_fir_instance_f32* S, - float32_t* pSrc, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the floating-point FIR filter. - * @param[in,out] S points to an instance of the floating-point FIR filter structure. - * @param[in] numTaps Number of filter coefficients in the filter. - * @param[in] pCoeffs points to the filter coefficients. - * @param[in] pState points to the state buffer. - * @param[in] blockSize number of samples that are processed at a time. - */ -void arm_fir_init_f32( - arm_fir_instance_f32* S, - uint16_t numTaps, - float32_t* pCoeffs, - float32_t* pState, - uint32_t blockSize); - - -/** - * @brief Instance structure for the Q15 Biquad cascade filter. - */ -typedef struct -{ - int8_t numStages; /**< number of 2nd order stages in the filter. Overall order is 2*numStages. */ - q15_t* pState; /**< Points to the array of state coefficients. The array is of length 4*numStages. */ - q15_t* pCoeffs; /**< Points to the array of coefficients. The array is of length 5*numStages. */ - int8_t postShift; /**< Additional shift, in bits, applied to each output sample. */ -} arm_biquad_casd_df1_inst_q15; - -/** - * @brief Instance structure for the Q31 Biquad cascade filter. - */ -typedef struct -{ - uint32_t numStages; /**< number of 2nd order stages in the filter. Overall order is 2*numStages. */ - q31_t* pState; /**< Points to the array of state coefficients. The array is of length 4*numStages. */ - q31_t* pCoeffs; /**< Points to the array of coefficients. The array is of length 5*numStages. */ - uint8_t postShift; /**< Additional shift, in bits, applied to each output sample. */ -} arm_biquad_casd_df1_inst_q31; - -/** - * @brief Instance structure for the floating-point Biquad cascade filter. - */ -typedef struct -{ - uint32_t numStages; /**< number of 2nd order stages in the filter. Overall order is 2*numStages. */ - float32_t* pState; /**< Points to the array of state coefficients. The array is of length 4*numStages. */ - float32_t* pCoeffs; /**< Points to the array of coefficients. The array is of length 5*numStages. */ -} arm_biquad_casd_df1_inst_f32; - - -/** - * @brief Processing function for the Q15 Biquad cascade filter. - * @param[in] S points to an instance of the Q15 Biquad cascade structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of samples to process. - */ -void arm_biquad_cascade_df1_q15( - const arm_biquad_casd_df1_inst_q15* S, - q15_t* pSrc, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the Q15 Biquad cascade filter. - * @param[in,out] S points to an instance of the Q15 Biquad cascade structure. - * @param[in] numStages number of 2nd order stages in the filter. - * @param[in] pCoeffs points to the filter coefficients. - * @param[in] pState points to the state buffer. - * @param[in] postShift Shift to be applied to the output. Varies according to the coefficients format - */ -void arm_biquad_cascade_df1_init_q15( - arm_biquad_casd_df1_inst_q15* S, - uint8_t numStages, - q15_t* pCoeffs, - q15_t* pState, - int8_t postShift); - - -/** - * @brief Fast but less precise processing function for the Q15 Biquad cascade filter for Cortex-M3 and Cortex-M4. - * @param[in] S points to an instance of the Q15 Biquad cascade structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of samples to process. - */ -void arm_biquad_cascade_df1_fast_q15( - const arm_biquad_casd_df1_inst_q15* S, - q15_t* pSrc, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Processing function for the Q31 Biquad cascade filter - * @param[in] S points to an instance of the Q31 Biquad cascade structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of samples to process. - */ -void arm_biquad_cascade_df1_q31( - const arm_biquad_casd_df1_inst_q31* S, - q31_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Fast but less precise processing function for the Q31 Biquad cascade filter for Cortex-M3 and Cortex-M4. - * @param[in] S points to an instance of the Q31 Biquad cascade structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of samples to process. - */ -void arm_biquad_cascade_df1_fast_q31( - const arm_biquad_casd_df1_inst_q31* S, - q31_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the Q31 Biquad cascade filter. - * @param[in,out] S points to an instance of the Q31 Biquad cascade structure. - * @param[in] numStages number of 2nd order stages in the filter. - * @param[in] pCoeffs points to the filter coefficients. - * @param[in] pState points to the state buffer. - * @param[in] postShift Shift to be applied to the output. Varies according to the coefficients format - */ -void arm_biquad_cascade_df1_init_q31( - arm_biquad_casd_df1_inst_q31* S, - uint8_t numStages, - q31_t* pCoeffs, - q31_t* pState, - int8_t postShift); - - -/** - * @brief Processing function for the floating-point Biquad cascade filter. - * @param[in] S points to an instance of the floating-point Biquad cascade structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of samples to process. - */ -void arm_biquad_cascade_df1_f32( - const arm_biquad_casd_df1_inst_f32* S, - float32_t* pSrc, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the floating-point Biquad cascade filter. - * @param[in,out] S points to an instance of the floating-point Biquad cascade structure. - * @param[in] numStages number of 2nd order stages in the filter. - * @param[in] pCoeffs points to the filter coefficients. - * @param[in] pState points to the state buffer. - */ -void arm_biquad_cascade_df1_init_f32( - arm_biquad_casd_df1_inst_f32* S, - uint8_t numStages, - float32_t* pCoeffs, - float32_t* pState); - - -/** - * @brief Instance structure for the floating-point matrix structure. - */ -typedef struct -{ - uint16_t numRows; /**< number of rows of the matrix. */ - uint16_t numCols; /**< number of columns of the matrix. */ - float32_t* pData; /**< points to the data of the matrix. */ -} arm_matrix_instance_f32; - - -/** - * @brief Instance structure for the floating-point matrix structure. - */ -typedef struct -{ - uint16_t numRows; /**< number of rows of the matrix. */ - uint16_t numCols; /**< number of columns of the matrix. */ - float64_t* pData; /**< points to the data of the matrix. */ -} arm_matrix_instance_f64; - -/** - * @brief Instance structure for the Q15 matrix structure. - */ -typedef struct -{ - uint16_t numRows; /**< number of rows of the matrix. */ - uint16_t numCols; /**< number of columns of the matrix. */ - q15_t* pData; /**< points to the data of the matrix. */ -} arm_matrix_instance_q15; - -/** - * @brief Instance structure for the Q31 matrix structure. - */ -typedef struct -{ - uint16_t numRows; /**< number of rows of the matrix. */ - uint16_t numCols; /**< number of columns of the matrix. */ - q31_t* pData; /**< points to the data of the matrix. */ -} arm_matrix_instance_q31; - - -/** - * @brief Floating-point matrix addition. - * @param[in] pSrcA points to the first input matrix structure - * @param[in] pSrcB points to the second input matrix structure - * @param[out] pDst points to output matrix structure - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_add_f32( - const arm_matrix_instance_f32* pSrcA, - const arm_matrix_instance_f32* pSrcB, - arm_matrix_instance_f32* pDst); - - -/** - * @brief Q15 matrix addition. - * @param[in] pSrcA points to the first input matrix structure - * @param[in] pSrcB points to the second input matrix structure - * @param[out] pDst points to output matrix structure - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_add_q15( - const arm_matrix_instance_q15* pSrcA, - const arm_matrix_instance_q15* pSrcB, - arm_matrix_instance_q15* pDst); - - -/** - * @brief Q31 matrix addition. - * @param[in] pSrcA points to the first input matrix structure - * @param[in] pSrcB points to the second input matrix structure - * @param[out] pDst points to output matrix structure - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_add_q31( - const arm_matrix_instance_q31* pSrcA, - const arm_matrix_instance_q31* pSrcB, - arm_matrix_instance_q31* pDst); - - -/** - * @brief Floating-point, complex, matrix multiplication. - * @param[in] pSrcA points to the first input matrix structure - * @param[in] pSrcB points to the second input matrix structure - * @param[out] pDst points to output matrix structure - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_cmplx_mult_f32( - const arm_matrix_instance_f32* pSrcA, - const arm_matrix_instance_f32* pSrcB, - arm_matrix_instance_f32* pDst); - - -/** - * @brief Q15, complex, matrix multiplication. - * @param[in] pSrcA points to the first input matrix structure - * @param[in] pSrcB points to the second input matrix structure - * @param[out] pDst points to output matrix structure - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_cmplx_mult_q15( - const arm_matrix_instance_q15* pSrcA, - const arm_matrix_instance_q15* pSrcB, - arm_matrix_instance_q15* pDst, - q15_t* pScratch); - - -/** - * @brief Q31, complex, matrix multiplication. - * @param[in] pSrcA points to the first input matrix structure - * @param[in] pSrcB points to the second input matrix structure - * @param[out] pDst points to output matrix structure - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_cmplx_mult_q31( - const arm_matrix_instance_q31* pSrcA, - const arm_matrix_instance_q31* pSrcB, - arm_matrix_instance_q31* pDst); - - -/** - * @brief Floating-point matrix transpose. - * @param[in] pSrc points to the input matrix - * @param[out] pDst points to the output matrix - * @return The function returns either ARM_MATH_SIZE_MISMATCH - * or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_trans_f32( - const arm_matrix_instance_f32* pSrc, - arm_matrix_instance_f32* pDst); - - -/** - * @brief Q15 matrix transpose. - * @param[in] pSrc points to the input matrix - * @param[out] pDst points to the output matrix - * @return The function returns either ARM_MATH_SIZE_MISMATCH - * or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_trans_q15( - const arm_matrix_instance_q15* pSrc, - arm_matrix_instance_q15* pDst); - - -/** - * @brief Q31 matrix transpose. - * @param[in] pSrc points to the input matrix - * @param[out] pDst points to the output matrix - * @return The function returns either ARM_MATH_SIZE_MISMATCH - * or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_trans_q31( - const arm_matrix_instance_q31* pSrc, - arm_matrix_instance_q31* pDst); - - -/** - * @brief Floating-point matrix multiplication - * @param[in] pSrcA points to the first input matrix structure - * @param[in] pSrcB points to the second input matrix structure - * @param[out] pDst points to output matrix structure - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_mult_f32( - const arm_matrix_instance_f32* pSrcA, - const arm_matrix_instance_f32* pSrcB, - arm_matrix_instance_f32* pDst); - - -/** - * @brief Q15 matrix multiplication - * @param[in] pSrcA points to the first input matrix structure - * @param[in] pSrcB points to the second input matrix structure - * @param[out] pDst points to output matrix structure - * @param[in] pState points to the array for storing intermediate results - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_mult_q15( - const arm_matrix_instance_q15* pSrcA, - const arm_matrix_instance_q15* pSrcB, - arm_matrix_instance_q15* pDst, - q15_t* pState); - - -/** - * @brief Q15 matrix multiplication (fast variant) for Cortex-M3 and Cortex-M4 - * @param[in] pSrcA points to the first input matrix structure - * @param[in] pSrcB points to the second input matrix structure - * @param[out] pDst points to output matrix structure - * @param[in] pState points to the array for storing intermediate results - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_mult_fast_q15( - const arm_matrix_instance_q15* pSrcA, - const arm_matrix_instance_q15* pSrcB, - arm_matrix_instance_q15* pDst, - q15_t* pState); - - -/** - * @brief Q31 matrix multiplication - * @param[in] pSrcA points to the first input matrix structure - * @param[in] pSrcB points to the second input matrix structure - * @param[out] pDst points to output matrix structure - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_mult_q31( - const arm_matrix_instance_q31* pSrcA, - const arm_matrix_instance_q31* pSrcB, - arm_matrix_instance_q31* pDst); - - -/** - * @brief Q31 matrix multiplication (fast variant) for Cortex-M3 and Cortex-M4 - * @param[in] pSrcA points to the first input matrix structure - * @param[in] pSrcB points to the second input matrix structure - * @param[out] pDst points to output matrix structure - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_mult_fast_q31( - const arm_matrix_instance_q31* pSrcA, - const arm_matrix_instance_q31* pSrcB, - arm_matrix_instance_q31* pDst); - - -/** - * @brief Floating-point matrix subtraction - * @param[in] pSrcA points to the first input matrix structure - * @param[in] pSrcB points to the second input matrix structure - * @param[out] pDst points to output matrix structure - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_sub_f32( - const arm_matrix_instance_f32* pSrcA, - const arm_matrix_instance_f32* pSrcB, - arm_matrix_instance_f32* pDst); - - -/** - * @brief Q15 matrix subtraction - * @param[in] pSrcA points to the first input matrix structure - * @param[in] pSrcB points to the second input matrix structure - * @param[out] pDst points to output matrix structure - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_sub_q15( - const arm_matrix_instance_q15* pSrcA, - const arm_matrix_instance_q15* pSrcB, - arm_matrix_instance_q15* pDst); - - -/** - * @brief Q31 matrix subtraction - * @param[in] pSrcA points to the first input matrix structure - * @param[in] pSrcB points to the second input matrix structure - * @param[out] pDst points to output matrix structure - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_sub_q31( - const arm_matrix_instance_q31* pSrcA, - const arm_matrix_instance_q31* pSrcB, - arm_matrix_instance_q31* pDst); - - -/** - * @brief Floating-point matrix scaling. - * @param[in] pSrc points to the input matrix - * @param[in] scale scale factor - * @param[out] pDst points to the output matrix - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_scale_f32( - const arm_matrix_instance_f32* pSrc, - float32_t scale, - arm_matrix_instance_f32* pDst); - - -/** - * @brief Q15 matrix scaling. - * @param[in] pSrc points to input matrix - * @param[in] scaleFract fractional portion of the scale factor - * @param[in] shift number of bits to shift the result by - * @param[out] pDst points to output matrix - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_scale_q15( - const arm_matrix_instance_q15* pSrc, - q15_t scaleFract, - int32_t shift, - arm_matrix_instance_q15* pDst); - - -/** - * @brief Q31 matrix scaling. - * @param[in] pSrc points to input matrix - * @param[in] scaleFract fractional portion of the scale factor - * @param[in] shift number of bits to shift the result by - * @param[out] pDst points to output matrix structure - * @return The function returns either - * ARM_MATH_SIZE_MISMATCH or ARM_MATH_SUCCESS based on the outcome of size checking. - */ -arm_status arm_mat_scale_q31( - const arm_matrix_instance_q31* pSrc, - q31_t scaleFract, - int32_t shift, - arm_matrix_instance_q31* pDst); - - -/** - * @brief Q31 matrix initialization. - * @param[in,out] S points to an instance of the floating-point matrix structure. - * @param[in] nRows number of rows in the matrix. - * @param[in] nColumns number of columns in the matrix. - * @param[in] pData points to the matrix data array. - */ -void arm_mat_init_q31( - arm_matrix_instance_q31* S, - uint16_t nRows, - uint16_t nColumns, - q31_t* pData); - - -/** - * @brief Q15 matrix initialization. - * @param[in,out] S points to an instance of the floating-point matrix structure. - * @param[in] nRows number of rows in the matrix. - * @param[in] nColumns number of columns in the matrix. - * @param[in] pData points to the matrix data array. - */ -void arm_mat_init_q15( - arm_matrix_instance_q15* S, - uint16_t nRows, - uint16_t nColumns, - q15_t* pData); - - -/** - * @brief Floating-point matrix initialization. - * @param[in,out] S points to an instance of the floating-point matrix structure. - * @param[in] nRows number of rows in the matrix. - * @param[in] nColumns number of columns in the matrix. - * @param[in] pData points to the matrix data array. - */ -void arm_mat_init_f32( - arm_matrix_instance_f32* S, - uint16_t nRows, - uint16_t nColumns, - float32_t* pData); - - - -/** - * @brief Instance structure for the Q15 PID Control. - */ -typedef struct -{ - q15_t A0; /**< The derived gain, A0 = Kp + Ki + Kd . */ -#ifdef ARM_MATH_CM0_FAMILY - q15_t A1; - q15_t A2; -#else - q31_t A1; /**< The derived gain A1 = -Kp - 2Kd | Kd.*/ -#endif - q15_t state[3]; /**< The state array of length 3. */ - q15_t Kp; /**< The proportional gain. */ - q15_t Ki; /**< The integral gain. */ - q15_t Kd; /**< The derivative gain. */ -} arm_pid_instance_q15; - -/** - * @brief Instance structure for the Q31 PID Control. - */ -typedef struct -{ - q31_t A0; /**< The derived gain, A0 = Kp + Ki + Kd . */ - q31_t A1; /**< The derived gain, A1 = -Kp - 2Kd. */ - q31_t A2; /**< The derived gain, A2 = Kd . */ - q31_t state[3]; /**< The state array of length 3. */ - q31_t Kp; /**< The proportional gain. */ - q31_t Ki; /**< The integral gain. */ - q31_t Kd; /**< The derivative gain. */ -} arm_pid_instance_q31; - -/** - * @brief Instance structure for the floating-point PID Control. - */ -typedef struct -{ - float32_t A0; /**< The derived gain, A0 = Kp + Ki + Kd . */ - float32_t A1; /**< The derived gain, A1 = -Kp - 2Kd. */ - float32_t A2; /**< The derived gain, A2 = Kd . */ - float32_t state[3]; /**< The state array of length 3. */ - float32_t Kp; /**< The proportional gain. */ - float32_t Ki; /**< The integral gain. */ - float32_t Kd; /**< The derivative gain. */ -} arm_pid_instance_f32; - - - -/** - * @brief Initialization function for the floating-point PID Control. - * @param[in,out] S points to an instance of the PID structure. - * @param[in] resetStateFlag flag to reset the state. 0 = no change in state 1 = reset the state. - */ -void arm_pid_init_f32( - arm_pid_instance_f32* S, - int32_t resetStateFlag); - - -/** - * @brief Reset function for the floating-point PID Control. - * @param[in,out] S is an instance of the floating-point PID Control structure - */ -void arm_pid_reset_f32( - arm_pid_instance_f32* S); - - -/** - * @brief Initialization function for the Q31 PID Control. - * @param[in,out] S points to an instance of the Q15 PID structure. - * @param[in] resetStateFlag flag to reset the state. 0 = no change in state 1 = reset the state. - */ -void arm_pid_init_q31( - arm_pid_instance_q31* S, - int32_t resetStateFlag); - - -/** - * @brief Reset function for the Q31 PID Control. - * @param[in,out] S points to an instance of the Q31 PID Control structure - */ - -void arm_pid_reset_q31( - arm_pid_instance_q31* S); - - -/** - * @brief Initialization function for the Q15 PID Control. - * @param[in,out] S points to an instance of the Q15 PID structure. - * @param[in] resetStateFlag flag to reset the state. 0 = no change in state 1 = reset the state. - */ -void arm_pid_init_q15( - arm_pid_instance_q15* S, - int32_t resetStateFlag); - - -/** - * @brief Reset function for the Q15 PID Control. - * @param[in,out] S points to an instance of the q15 PID Control structure - */ -void arm_pid_reset_q15( - arm_pid_instance_q15* S); - - -/** - * @brief Instance structure for the floating-point Linear Interpolate function. - */ -typedef struct -{ - uint32_t nValues; /**< nValues */ - float32_t x1; /**< x1 */ - float32_t xSpacing; /**< xSpacing */ - float32_t* pYData; /**< pointer to the table of Y values */ -} arm_linear_interp_instance_f32; - -/** - * @brief Instance structure for the floating-point bilinear interpolation function. - */ -typedef struct -{ - uint16_t numRows; /**< number of rows in the data table. */ - uint16_t numCols; /**< number of columns in the data table. */ - float32_t* pData; /**< points to the data table. */ -} arm_bilinear_interp_instance_f32; - -/** -* @brief Instance structure for the Q31 bilinear interpolation function. -*/ -typedef struct -{ - uint16_t numRows; /**< number of rows in the data table. */ - uint16_t numCols; /**< number of columns in the data table. */ - q31_t* pData; /**< points to the data table. */ -} arm_bilinear_interp_instance_q31; - -/** -* @brief Instance structure for the Q15 bilinear interpolation function. -*/ -typedef struct -{ - uint16_t numRows; /**< number of rows in the data table. */ - uint16_t numCols; /**< number of columns in the data table. */ - q15_t* pData; /**< points to the data table. */ -} arm_bilinear_interp_instance_q15; - -/** -* @brief Instance structure for the Q15 bilinear interpolation function. -*/ -typedef struct -{ - uint16_t numRows; /**< number of rows in the data table. */ - uint16_t numCols; /**< number of columns in the data table. */ - q7_t* pData; /**< points to the data table. */ -} arm_bilinear_interp_instance_q7; - - -/** - * @brief Q7 vector multiplication. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in each vector - */ -void arm_mult_q7( - q7_t* pSrcA, - q7_t* pSrcB, - q7_t* pDst, - uint32_t blockSize); - - -/** - * @brief Q15 vector multiplication. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in each vector - */ -void arm_mult_q15( - q15_t* pSrcA, - q15_t* pSrcB, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Q31 vector multiplication. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in each vector - */ -void arm_mult_q31( - q31_t* pSrcA, - q31_t* pSrcB, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Floating-point vector multiplication. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in each vector - */ -void arm_mult_f32( - float32_t* pSrcA, - float32_t* pSrcB, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Instance structure for the Q15 CFFT/CIFFT function. - */ -typedef struct -{ - uint16_t fftLen; /**< length of the FFT. */ - uint8_t ifftFlag; /**< flag that selects forward (ifftFlag=0) or inverse (ifftFlag=1) transform. */ - uint8_t bitReverseFlag; /**< flag that enables (bitReverseFlag=1) or disables (bitReverseFlag=0) bit reversal of output. */ - q15_t* pTwiddle; /**< points to the Sin twiddle factor table. */ - uint16_t* pBitRevTable; /**< points to the bit reversal table. */ - uint16_t twidCoefModifier; /**< twiddle coefficient modifier that supports different size FFTs with the same twiddle factor table. */ - uint16_t bitRevFactor; /**< bit reversal modifier that supports different size FFTs with the same bit reversal table. */ -} arm_cfft_radix2_instance_q15; - -/* Deprecated */ -arm_status arm_cfft_radix2_init_q15( - arm_cfft_radix2_instance_q15* S, - uint16_t fftLen, - uint8_t ifftFlag, - uint8_t bitReverseFlag); - -/* Deprecated */ -void arm_cfft_radix2_q15( - const arm_cfft_radix2_instance_q15* S, - q15_t* pSrc); - - -/** - * @brief Instance structure for the Q15 CFFT/CIFFT function. - */ -typedef struct -{ - uint16_t fftLen; /**< length of the FFT. */ - uint8_t ifftFlag; /**< flag that selects forward (ifftFlag=0) or inverse (ifftFlag=1) transform. */ - uint8_t bitReverseFlag; /**< flag that enables (bitReverseFlag=1) or disables (bitReverseFlag=0) bit reversal of output. */ - q15_t* pTwiddle; /**< points to the twiddle factor table. */ - uint16_t* pBitRevTable; /**< points to the bit reversal table. */ - uint16_t twidCoefModifier; /**< twiddle coefficient modifier that supports different size FFTs with the same twiddle factor table. */ - uint16_t bitRevFactor; /**< bit reversal modifier that supports different size FFTs with the same bit reversal table. */ -} arm_cfft_radix4_instance_q15; - -/* Deprecated */ -arm_status arm_cfft_radix4_init_q15( - arm_cfft_radix4_instance_q15* S, - uint16_t fftLen, - uint8_t ifftFlag, - uint8_t bitReverseFlag); - -/* Deprecated */ -void arm_cfft_radix4_q15( - const arm_cfft_radix4_instance_q15* S, - q15_t* pSrc); - -/** - * @brief Instance structure for the Radix-2 Q31 CFFT/CIFFT function. - */ -typedef struct -{ - uint16_t fftLen; /**< length of the FFT. */ - uint8_t ifftFlag; /**< flag that selects forward (ifftFlag=0) or inverse (ifftFlag=1) transform. */ - uint8_t bitReverseFlag; /**< flag that enables (bitReverseFlag=1) or disables (bitReverseFlag=0) bit reversal of output. */ - q31_t* pTwiddle; /**< points to the Twiddle factor table. */ - uint16_t* pBitRevTable; /**< points to the bit reversal table. */ - uint16_t twidCoefModifier; /**< twiddle coefficient modifier that supports different size FFTs with the same twiddle factor table. */ - uint16_t bitRevFactor; /**< bit reversal modifier that supports different size FFTs with the same bit reversal table. */ -} arm_cfft_radix2_instance_q31; - -/* Deprecated */ -arm_status arm_cfft_radix2_init_q31( - arm_cfft_radix2_instance_q31* S, - uint16_t fftLen, - uint8_t ifftFlag, - uint8_t bitReverseFlag); - -/* Deprecated */ -void arm_cfft_radix2_q31( - const arm_cfft_radix2_instance_q31* S, - q31_t* pSrc); - -/** - * @brief Instance structure for the Q31 CFFT/CIFFT function. - */ -typedef struct -{ - uint16_t fftLen; /**< length of the FFT. */ - uint8_t ifftFlag; /**< flag that selects forward (ifftFlag=0) or inverse (ifftFlag=1) transform. */ - uint8_t bitReverseFlag; /**< flag that enables (bitReverseFlag=1) or disables (bitReverseFlag=0) bit reversal of output. */ - q31_t* pTwiddle; /**< points to the twiddle factor table. */ - uint16_t* pBitRevTable; /**< points to the bit reversal table. */ - uint16_t twidCoefModifier; /**< twiddle coefficient modifier that supports different size FFTs with the same twiddle factor table. */ - uint16_t bitRevFactor; /**< bit reversal modifier that supports different size FFTs with the same bit reversal table. */ -} arm_cfft_radix4_instance_q31; - -/* Deprecated */ -void arm_cfft_radix4_q31( - const arm_cfft_radix4_instance_q31* S, - q31_t* pSrc); - -/* Deprecated */ -arm_status arm_cfft_radix4_init_q31( - arm_cfft_radix4_instance_q31* S, - uint16_t fftLen, - uint8_t ifftFlag, - uint8_t bitReverseFlag); - -/** - * @brief Instance structure for the floating-point CFFT/CIFFT function. - */ -typedef struct -{ - uint16_t fftLen; /**< length of the FFT. */ - uint8_t ifftFlag; /**< flag that selects forward (ifftFlag=0) or inverse (ifftFlag=1) transform. */ - uint8_t bitReverseFlag; /**< flag that enables (bitReverseFlag=1) or disables (bitReverseFlag=0) bit reversal of output. */ - float32_t* pTwiddle; /**< points to the Twiddle factor table. */ - uint16_t* pBitRevTable; /**< points to the bit reversal table. */ - uint16_t twidCoefModifier; /**< twiddle coefficient modifier that supports different size FFTs with the same twiddle factor table. */ - uint16_t bitRevFactor; /**< bit reversal modifier that supports different size FFTs with the same bit reversal table. */ - float32_t onebyfftLen; /**< value of 1/fftLen. */ -} arm_cfft_radix2_instance_f32; - -/* Deprecated */ -arm_status arm_cfft_radix2_init_f32( - arm_cfft_radix2_instance_f32* S, - uint16_t fftLen, - uint8_t ifftFlag, - uint8_t bitReverseFlag); - -/* Deprecated */ -void arm_cfft_radix2_f32( - const arm_cfft_radix2_instance_f32* S, - float32_t* pSrc); - -/** - * @brief Instance structure for the floating-point CFFT/CIFFT function. - */ -typedef struct -{ - uint16_t fftLen; /**< length of the FFT. */ - uint8_t ifftFlag; /**< flag that selects forward (ifftFlag=0) or inverse (ifftFlag=1) transform. */ - uint8_t bitReverseFlag; /**< flag that enables (bitReverseFlag=1) or disables (bitReverseFlag=0) bit reversal of output. */ - float32_t* pTwiddle; /**< points to the Twiddle factor table. */ - uint16_t* pBitRevTable; /**< points to the bit reversal table. */ - uint16_t twidCoefModifier; /**< twiddle coefficient modifier that supports different size FFTs with the same twiddle factor table. */ - uint16_t bitRevFactor; /**< bit reversal modifier that supports different size FFTs with the same bit reversal table. */ - float32_t onebyfftLen; /**< value of 1/fftLen. */ -} arm_cfft_radix4_instance_f32; - -/* Deprecated */ -arm_status arm_cfft_radix4_init_f32( - arm_cfft_radix4_instance_f32* S, - uint16_t fftLen, - uint8_t ifftFlag, - uint8_t bitReverseFlag); - -/* Deprecated */ -void arm_cfft_radix4_f32( - const arm_cfft_radix4_instance_f32* S, - float32_t* pSrc); - -/** - * @brief Instance structure for the fixed-point CFFT/CIFFT function. - */ -typedef struct -{ - uint16_t fftLen; /**< length of the FFT. */ - const q15_t* pTwiddle; /**< points to the Twiddle factor table. */ - const uint16_t* pBitRevTable; /**< points to the bit reversal table. */ - uint16_t bitRevLength; /**< bit reversal table length. */ -} arm_cfft_instance_q15; - -void arm_cfft_q15( - const arm_cfft_instance_q15* S, - q15_t* p1, - uint8_t ifftFlag, - uint8_t bitReverseFlag); - -/** - * @brief Instance structure for the fixed-point CFFT/CIFFT function. - */ -typedef struct -{ - uint16_t fftLen; /**< length of the FFT. */ - const q31_t* pTwiddle; /**< points to the Twiddle factor table. */ - const uint16_t* pBitRevTable; /**< points to the bit reversal table. */ - uint16_t bitRevLength; /**< bit reversal table length. */ -} arm_cfft_instance_q31; - -void arm_cfft_q31( - const arm_cfft_instance_q31* S, - q31_t* p1, - uint8_t ifftFlag, - uint8_t bitReverseFlag); - -/** - * @brief Instance structure for the floating-point CFFT/CIFFT function. - */ -typedef struct -{ - uint16_t fftLen; /**< length of the FFT. */ - const float32_t* pTwiddle; /**< points to the Twiddle factor table. */ - const uint16_t* pBitRevTable; /**< points to the bit reversal table. */ - uint16_t bitRevLength; /**< bit reversal table length. */ -} arm_cfft_instance_f32; - -void arm_cfft_f32( - const arm_cfft_instance_f32* S, - float32_t* p1, - uint8_t ifftFlag, - uint8_t bitReverseFlag); - -/** - * @brief Instance structure for the Q15 RFFT/RIFFT function. - */ -typedef struct -{ - uint32_t fftLenReal; /**< length of the real FFT. */ - uint8_t ifftFlagR; /**< flag that selects forward (ifftFlagR=0) or inverse (ifftFlagR=1) transform. */ - uint8_t bitReverseFlagR; /**< flag that enables (bitReverseFlagR=1) or disables (bitReverseFlagR=0) bit reversal of output. */ - uint32_t twidCoefRModifier; /**< twiddle coefficient modifier that supports different size FFTs with the same twiddle factor table. */ - q15_t* pTwiddleAReal; /**< points to the real twiddle factor table. */ - q15_t* pTwiddleBReal; /**< points to the imag twiddle factor table. */ - const arm_cfft_instance_q15* pCfft; /**< points to the complex FFT instance. */ -} arm_rfft_instance_q15; - -arm_status arm_rfft_init_q15( - arm_rfft_instance_q15* S, - uint32_t fftLenReal, - uint32_t ifftFlagR, - uint32_t bitReverseFlag); - -void arm_rfft_q15( - const arm_rfft_instance_q15* S, - q15_t* pSrc, - q15_t* pDst); - -/** - * @brief Instance structure for the Q31 RFFT/RIFFT function. - */ -typedef struct -{ - uint32_t fftLenReal; /**< length of the real FFT. */ - uint8_t ifftFlagR; /**< flag that selects forward (ifftFlagR=0) or inverse (ifftFlagR=1) transform. */ - uint8_t bitReverseFlagR; /**< flag that enables (bitReverseFlagR=1) or disables (bitReverseFlagR=0) bit reversal of output. */ - uint32_t twidCoefRModifier; /**< twiddle coefficient modifier that supports different size FFTs with the same twiddle factor table. */ - q31_t* pTwiddleAReal; /**< points to the real twiddle factor table. */ - q31_t* pTwiddleBReal; /**< points to the imag twiddle factor table. */ - const arm_cfft_instance_q31* pCfft; /**< points to the complex FFT instance. */ -} arm_rfft_instance_q31; - -arm_status arm_rfft_init_q31( - arm_rfft_instance_q31* S, - uint32_t fftLenReal, - uint32_t ifftFlagR, - uint32_t bitReverseFlag); - -void arm_rfft_q31( - const arm_rfft_instance_q31* S, - q31_t* pSrc, - q31_t* pDst); - -/** - * @brief Instance structure for the floating-point RFFT/RIFFT function. - */ -typedef struct -{ - uint32_t fftLenReal; /**< length of the real FFT. */ - uint16_t fftLenBy2; /**< length of the complex FFT. */ - uint8_t ifftFlagR; /**< flag that selects forward (ifftFlagR=0) or inverse (ifftFlagR=1) transform. */ - uint8_t bitReverseFlagR; /**< flag that enables (bitReverseFlagR=1) or disables (bitReverseFlagR=0) bit reversal of output. */ - uint32_t twidCoefRModifier; /**< twiddle coefficient modifier that supports different size FFTs with the same twiddle factor table. */ - float32_t* pTwiddleAReal; /**< points to the real twiddle factor table. */ - float32_t* pTwiddleBReal; /**< points to the imag twiddle factor table. */ - arm_cfft_radix4_instance_f32* pCfft; /**< points to the complex FFT instance. */ -} arm_rfft_instance_f32; - -arm_status arm_rfft_init_f32( - arm_rfft_instance_f32* S, - arm_cfft_radix4_instance_f32* S_CFFT, - uint32_t fftLenReal, - uint32_t ifftFlagR, - uint32_t bitReverseFlag); - -void arm_rfft_f32( - const arm_rfft_instance_f32* S, - float32_t* pSrc, - float32_t* pDst); - -/** - * @brief Instance structure for the floating-point RFFT/RIFFT function. - */ -typedef struct -{ - arm_cfft_instance_f32 Sint; /**< Internal CFFT structure. */ - uint16_t fftLenRFFT; /**< length of the real sequence */ - float32_t* pTwiddleRFFT; /**< Twiddle factors real stage */ -} arm_rfft_fast_instance_f32 ; - -arm_status arm_rfft_fast_init_f32 ( - arm_rfft_fast_instance_f32* S, - uint16_t fftLen); - -void arm_rfft_fast_f32( - arm_rfft_fast_instance_f32* S, - float32_t* p, float32_t* pOut, - uint8_t ifftFlag); - -/** - * @brief Instance structure for the floating-point DCT4/IDCT4 function. - */ -typedef struct -{ - uint16_t N; /**< length of the DCT4. */ - uint16_t Nby2; /**< half of the length of the DCT4. */ - float32_t normalize; /**< normalizing factor. */ - float32_t* pTwiddle; /**< points to the twiddle factor table. */ - float32_t* pCosFactor; /**< points to the cosFactor table. */ - arm_rfft_instance_f32* pRfft; /**< points to the real FFT instance. */ - arm_cfft_radix4_instance_f32* pCfft; /**< points to the complex FFT instance. */ -} arm_dct4_instance_f32; - - -/** - * @brief Initialization function for the floating-point DCT4/IDCT4. - * @param[in,out] S points to an instance of floating-point DCT4/IDCT4 structure. - * @param[in] S_RFFT points to an instance of floating-point RFFT/RIFFT structure. - * @param[in] S_CFFT points to an instance of floating-point CFFT/CIFFT structure. - * @param[in] N length of the DCT4. - * @param[in] Nby2 half of the length of the DCT4. - * @param[in] normalize normalizing factor. - * @return arm_status function returns ARM_MATH_SUCCESS if initialization is successful or ARM_MATH_ARGUMENT_ERROR if fftLenReal is not a supported transform length. - */ -arm_status arm_dct4_init_f32( - arm_dct4_instance_f32* S, - arm_rfft_instance_f32* S_RFFT, - arm_cfft_radix4_instance_f32* S_CFFT, - uint16_t N, - uint16_t Nby2, - float32_t normalize); - - -/** - * @brief Processing function for the floating-point DCT4/IDCT4. - * @param[in] S points to an instance of the floating-point DCT4/IDCT4 structure. - * @param[in] pState points to state buffer. - * @param[in,out] pInlineBuffer points to the in-place input and output buffer. - */ -void arm_dct4_f32( - const arm_dct4_instance_f32* S, - float32_t* pState, - float32_t* pInlineBuffer); - - -/** - * @brief Instance structure for the Q31 DCT4/IDCT4 function. - */ -typedef struct -{ - uint16_t N; /**< length of the DCT4. */ - uint16_t Nby2; /**< half of the length of the DCT4. */ - q31_t normalize; /**< normalizing factor. */ - q31_t* pTwiddle; /**< points to the twiddle factor table. */ - q31_t* pCosFactor; /**< points to the cosFactor table. */ - arm_rfft_instance_q31* pRfft; /**< points to the real FFT instance. */ - arm_cfft_radix4_instance_q31* pCfft; /**< points to the complex FFT instance. */ -} arm_dct4_instance_q31; - - -/** - * @brief Initialization function for the Q31 DCT4/IDCT4. - * @param[in,out] S points to an instance of Q31 DCT4/IDCT4 structure. - * @param[in] S_RFFT points to an instance of Q31 RFFT/RIFFT structure - * @param[in] S_CFFT points to an instance of Q31 CFFT/CIFFT structure - * @param[in] N length of the DCT4. - * @param[in] Nby2 half of the length of the DCT4. - * @param[in] normalize normalizing factor. - * @return arm_status function returns ARM_MATH_SUCCESS if initialization is successful or ARM_MATH_ARGUMENT_ERROR if N is not a supported transform length. - */ -arm_status arm_dct4_init_q31( - arm_dct4_instance_q31* S, - arm_rfft_instance_q31* S_RFFT, - arm_cfft_radix4_instance_q31* S_CFFT, - uint16_t N, - uint16_t Nby2, - q31_t normalize); - - -/** - * @brief Processing function for the Q31 DCT4/IDCT4. - * @param[in] S points to an instance of the Q31 DCT4 structure. - * @param[in] pState points to state buffer. - * @param[in,out] pInlineBuffer points to the in-place input and output buffer. - */ -void arm_dct4_q31( - const arm_dct4_instance_q31* S, - q31_t* pState, - q31_t* pInlineBuffer); - - -/** - * @brief Instance structure for the Q15 DCT4/IDCT4 function. - */ -typedef struct -{ - uint16_t N; /**< length of the DCT4. */ - uint16_t Nby2; /**< half of the length of the DCT4. */ - q15_t normalize; /**< normalizing factor. */ - q15_t* pTwiddle; /**< points to the twiddle factor table. */ - q15_t* pCosFactor; /**< points to the cosFactor table. */ - arm_rfft_instance_q15* pRfft; /**< points to the real FFT instance. */ - arm_cfft_radix4_instance_q15* pCfft; /**< points to the complex FFT instance. */ -} arm_dct4_instance_q15; - - -/** - * @brief Initialization function for the Q15 DCT4/IDCT4. - * @param[in,out] S points to an instance of Q15 DCT4/IDCT4 structure. - * @param[in] S_RFFT points to an instance of Q15 RFFT/RIFFT structure. - * @param[in] S_CFFT points to an instance of Q15 CFFT/CIFFT structure. - * @param[in] N length of the DCT4. - * @param[in] Nby2 half of the length of the DCT4. - * @param[in] normalize normalizing factor. - * @return arm_status function returns ARM_MATH_SUCCESS if initialization is successful or ARM_MATH_ARGUMENT_ERROR if N is not a supported transform length. - */ -arm_status arm_dct4_init_q15( - arm_dct4_instance_q15* S, - arm_rfft_instance_q15* S_RFFT, - arm_cfft_radix4_instance_q15* S_CFFT, - uint16_t N, - uint16_t Nby2, - q15_t normalize); - - -/** - * @brief Processing function for the Q15 DCT4/IDCT4. - * @param[in] S points to an instance of the Q15 DCT4 structure. - * @param[in] pState points to state buffer. - * @param[in,out] pInlineBuffer points to the in-place input and output buffer. - */ -void arm_dct4_q15( - const arm_dct4_instance_q15* S, - q15_t* pState, - q15_t* pInlineBuffer); - - -/** - * @brief Floating-point vector addition. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in each vector - */ -void arm_add_f32( - float32_t* pSrcA, - float32_t* pSrcB, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Q7 vector addition. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in each vector - */ -void arm_add_q7( - q7_t* pSrcA, - q7_t* pSrcB, - q7_t* pDst, - uint32_t blockSize); - - -/** - * @brief Q15 vector addition. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in each vector - */ -void arm_add_q15( - q15_t* pSrcA, - q15_t* pSrcB, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Q31 vector addition. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in each vector - */ -void arm_add_q31( - q31_t* pSrcA, - q31_t* pSrcB, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Floating-point vector subtraction. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in each vector - */ -void arm_sub_f32( - float32_t* pSrcA, - float32_t* pSrcB, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Q7 vector subtraction. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in each vector - */ -void arm_sub_q7( - q7_t* pSrcA, - q7_t* pSrcB, - q7_t* pDst, - uint32_t blockSize); - - -/** - * @brief Q15 vector subtraction. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in each vector - */ -void arm_sub_q15( - q15_t* pSrcA, - q15_t* pSrcB, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Q31 vector subtraction. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in each vector - */ -void arm_sub_q31( - q31_t* pSrcA, - q31_t* pSrcB, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Multiplies a floating-point vector by a scalar. - * @param[in] pSrc points to the input vector - * @param[in] scale scale factor to be applied - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in the vector - */ -void arm_scale_f32( - float32_t* pSrc, - float32_t scale, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Multiplies a Q7 vector by a scalar. - * @param[in] pSrc points to the input vector - * @param[in] scaleFract fractional portion of the scale value - * @param[in] shift number of bits to shift the result by - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in the vector - */ -void arm_scale_q7( - q7_t* pSrc, - q7_t scaleFract, - int8_t shift, - q7_t* pDst, - uint32_t blockSize); - - -/** - * @brief Multiplies a Q15 vector by a scalar. - * @param[in] pSrc points to the input vector - * @param[in] scaleFract fractional portion of the scale value - * @param[in] shift number of bits to shift the result by - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in the vector - */ -void arm_scale_q15( - q15_t* pSrc, - q15_t scaleFract, - int8_t shift, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Multiplies a Q31 vector by a scalar. - * @param[in] pSrc points to the input vector - * @param[in] scaleFract fractional portion of the scale value - * @param[in] shift number of bits to shift the result by - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in the vector - */ -void arm_scale_q31( - q31_t* pSrc, - q31_t scaleFract, - int8_t shift, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Q7 vector absolute value. - * @param[in] pSrc points to the input buffer - * @param[out] pDst points to the output buffer - * @param[in] blockSize number of samples in each vector - */ -void arm_abs_q7( - q7_t* pSrc, - q7_t* pDst, - uint32_t blockSize); - - -/** - * @brief Floating-point vector absolute value. - * @param[in] pSrc points to the input buffer - * @param[out] pDst points to the output buffer - * @param[in] blockSize number of samples in each vector - */ -void arm_abs_f32( - float32_t* pSrc, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Q15 vector absolute value. - * @param[in] pSrc points to the input buffer - * @param[out] pDst points to the output buffer - * @param[in] blockSize number of samples in each vector - */ -void arm_abs_q15( - q15_t* pSrc, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Q31 vector absolute value. - * @param[in] pSrc points to the input buffer - * @param[out] pDst points to the output buffer - * @param[in] blockSize number of samples in each vector - */ -void arm_abs_q31( - q31_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Dot product of floating-point vectors. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[in] blockSize number of samples in each vector - * @param[out] result output result returned here - */ -void arm_dot_prod_f32( - float32_t* pSrcA, - float32_t* pSrcB, - uint32_t blockSize, - float32_t* result); - - -/** - * @brief Dot product of Q7 vectors. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[in] blockSize number of samples in each vector - * @param[out] result output result returned here - */ -void arm_dot_prod_q7( - q7_t* pSrcA, - q7_t* pSrcB, - uint32_t blockSize, - q31_t* result); - - -/** - * @brief Dot product of Q15 vectors. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[in] blockSize number of samples in each vector - * @param[out] result output result returned here - */ -void arm_dot_prod_q15( - q15_t* pSrcA, - q15_t* pSrcB, - uint32_t blockSize, - q63_t* result); - - -/** - * @brief Dot product of Q31 vectors. - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[in] blockSize number of samples in each vector - * @param[out] result output result returned here - */ -void arm_dot_prod_q31( - q31_t* pSrcA, - q31_t* pSrcB, - uint32_t blockSize, - q63_t* result); - - -/** - * @brief Shifts the elements of a Q7 vector a specified number of bits. - * @param[in] pSrc points to the input vector - * @param[in] shiftBits number of bits to shift. A positive value shifts left; a negative value shifts right. - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in the vector - */ -void arm_shift_q7( - q7_t* pSrc, - int8_t shiftBits, - q7_t* pDst, - uint32_t blockSize); - - -/** - * @brief Shifts the elements of a Q15 vector a specified number of bits. - * @param[in] pSrc points to the input vector - * @param[in] shiftBits number of bits to shift. A positive value shifts left; a negative value shifts right. - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in the vector - */ -void arm_shift_q15( - q15_t* pSrc, - int8_t shiftBits, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Shifts the elements of a Q31 vector a specified number of bits. - * @param[in] pSrc points to the input vector - * @param[in] shiftBits number of bits to shift. A positive value shifts left; a negative value shifts right. - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in the vector - */ -void arm_shift_q31( - q31_t* pSrc, - int8_t shiftBits, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Adds a constant offset to a floating-point vector. - * @param[in] pSrc points to the input vector - * @param[in] offset is the offset to be added - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in the vector - */ -void arm_offset_f32( - float32_t* pSrc, - float32_t offset, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Adds a constant offset to a Q7 vector. - * @param[in] pSrc points to the input vector - * @param[in] offset is the offset to be added - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in the vector - */ -void arm_offset_q7( - q7_t* pSrc, - q7_t offset, - q7_t* pDst, - uint32_t blockSize); - - -/** - * @brief Adds a constant offset to a Q15 vector. - * @param[in] pSrc points to the input vector - * @param[in] offset is the offset to be added - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in the vector - */ -void arm_offset_q15( - q15_t* pSrc, - q15_t offset, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Adds a constant offset to a Q31 vector. - * @param[in] pSrc points to the input vector - * @param[in] offset is the offset to be added - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in the vector - */ -void arm_offset_q31( - q31_t* pSrc, - q31_t offset, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Negates the elements of a floating-point vector. - * @param[in] pSrc points to the input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in the vector - */ -void arm_negate_f32( - float32_t* pSrc, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Negates the elements of a Q7 vector. - * @param[in] pSrc points to the input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in the vector - */ -void arm_negate_q7( - q7_t* pSrc, - q7_t* pDst, - uint32_t blockSize); - - -/** - * @brief Negates the elements of a Q15 vector. - * @param[in] pSrc points to the input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in the vector - */ -void arm_negate_q15( - q15_t* pSrc, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Negates the elements of a Q31 vector. - * @param[in] pSrc points to the input vector - * @param[out] pDst points to the output vector - * @param[in] blockSize number of samples in the vector - */ -void arm_negate_q31( - q31_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Copies the elements of a floating-point vector. - * @param[in] pSrc input pointer - * @param[out] pDst output pointer - * @param[in] blockSize number of samples to process - */ -void arm_copy_f32( - float32_t* pSrc, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Copies the elements of a Q7 vector. - * @param[in] pSrc input pointer - * @param[out] pDst output pointer - * @param[in] blockSize number of samples to process - */ -void arm_copy_q7( - q7_t* pSrc, - q7_t* pDst, - uint32_t blockSize); - - -/** - * @brief Copies the elements of a Q15 vector. - * @param[in] pSrc input pointer - * @param[out] pDst output pointer - * @param[in] blockSize number of samples to process - */ -void arm_copy_q15( - q15_t* pSrc, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Copies the elements of a Q31 vector. - * @param[in] pSrc input pointer - * @param[out] pDst output pointer - * @param[in] blockSize number of samples to process - */ -void arm_copy_q31( - q31_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Fills a constant value into a floating-point vector. - * @param[in] value input value to be filled - * @param[out] pDst output pointer - * @param[in] blockSize number of samples to process - */ -void arm_fill_f32( - float32_t value, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Fills a constant value into a Q7 vector. - * @param[in] value input value to be filled - * @param[out] pDst output pointer - * @param[in] blockSize number of samples to process - */ -void arm_fill_q7( - q7_t value, - q7_t* pDst, - uint32_t blockSize); - - -/** - * @brief Fills a constant value into a Q15 vector. - * @param[in] value input value to be filled - * @param[out] pDst output pointer - * @param[in] blockSize number of samples to process - */ -void arm_fill_q15( - q15_t value, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Fills a constant value into a Q31 vector. - * @param[in] value input value to be filled - * @param[out] pDst output pointer - * @param[in] blockSize number of samples to process - */ -void arm_fill_q31( - q31_t value, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Convolution of floating-point sequences. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the location where the output result is written. Length srcALen+srcBLen-1. - */ -void arm_conv_f32( - float32_t* pSrcA, - uint32_t srcALen, - float32_t* pSrcB, - uint32_t srcBLen, - float32_t* pDst); - - -/** - * @brief Convolution of Q15 sequences. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data Length srcALen+srcBLen-1. - * @param[in] pScratch1 points to scratch buffer of size max(srcALen, srcBLen) + 2*min(srcALen, srcBLen) - 2. - * @param[in] pScratch2 points to scratch buffer of size min(srcALen, srcBLen). - */ -void arm_conv_opt_q15( - q15_t* pSrcA, - uint32_t srcALen, - q15_t* pSrcB, - uint32_t srcBLen, - q15_t* pDst, - q15_t* pScratch1, - q15_t* pScratch2); - - -/** - * @brief Convolution of Q15 sequences. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the location where the output result is written. Length srcALen+srcBLen-1. - */ -void arm_conv_q15( - q15_t* pSrcA, - uint32_t srcALen, - q15_t* pSrcB, - uint32_t srcBLen, - q15_t* pDst); - - -/** - * @brief Convolution of Q15 sequences (fast version) for Cortex-M3 and Cortex-M4 - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data Length srcALen+srcBLen-1. - */ -void arm_conv_fast_q15( - q15_t* pSrcA, - uint32_t srcALen, - q15_t* pSrcB, - uint32_t srcBLen, - q15_t* pDst); - - -/** - * @brief Convolution of Q15 sequences (fast version) for Cortex-M3 and Cortex-M4 - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data Length srcALen+srcBLen-1. - * @param[in] pScratch1 points to scratch buffer of size max(srcALen, srcBLen) + 2*min(srcALen, srcBLen) - 2. - * @param[in] pScratch2 points to scratch buffer of size min(srcALen, srcBLen). - */ -void arm_conv_fast_opt_q15( - q15_t* pSrcA, - uint32_t srcALen, - q15_t* pSrcB, - uint32_t srcBLen, - q15_t* pDst, - q15_t* pScratch1, - q15_t* pScratch2); - - -/** - * @brief Convolution of Q31 sequences. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data Length srcALen+srcBLen-1. - */ -void arm_conv_q31( - q31_t* pSrcA, - uint32_t srcALen, - q31_t* pSrcB, - uint32_t srcBLen, - q31_t* pDst); - - -/** - * @brief Convolution of Q31 sequences (fast version) for Cortex-M3 and Cortex-M4 - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data Length srcALen+srcBLen-1. - */ -void arm_conv_fast_q31( - q31_t* pSrcA, - uint32_t srcALen, - q31_t* pSrcB, - uint32_t srcBLen, - q31_t* pDst); - - -/** -* @brief Convolution of Q7 sequences. -* @param[in] pSrcA points to the first input sequence. -* @param[in] srcALen length of the first input sequence. -* @param[in] pSrcB points to the second input sequence. -* @param[in] srcBLen length of the second input sequence. -* @param[out] pDst points to the block of output data Length srcALen+srcBLen-1. -* @param[in] pScratch1 points to scratch buffer(of type q15_t) of size max(srcALen, srcBLen) + 2*min(srcALen, srcBLen) - 2. -* @param[in] pScratch2 points to scratch buffer (of type q15_t) of size min(srcALen, srcBLen). -*/ -void arm_conv_opt_q7( - q7_t* pSrcA, - uint32_t srcALen, - q7_t* pSrcB, - uint32_t srcBLen, - q7_t* pDst, - q15_t* pScratch1, - q15_t* pScratch2); - - -/** - * @brief Convolution of Q7 sequences. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data Length srcALen+srcBLen-1. - */ -void arm_conv_q7( - q7_t* pSrcA, - uint32_t srcALen, - q7_t* pSrcB, - uint32_t srcBLen, - q7_t* pDst); - - -/** - * @brief Partial convolution of floating-point sequences. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data - * @param[in] firstIndex is the first output sample to start with. - * @param[in] numPoints is the number of output points to be computed. - * @return Returns either ARM_MATH_SUCCESS if the function completed correctly or ARM_MATH_ARGUMENT_ERROR if the requested subset is not in the range [0 srcALen+srcBLen-2]. - */ -arm_status arm_conv_partial_f32( - float32_t* pSrcA, - uint32_t srcALen, - float32_t* pSrcB, - uint32_t srcBLen, - float32_t* pDst, - uint32_t firstIndex, - uint32_t numPoints); - - -/** - * @brief Partial convolution of Q15 sequences. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data - * @param[in] firstIndex is the first output sample to start with. - * @param[in] numPoints is the number of output points to be computed. - * @param[in] pScratch1 points to scratch buffer of size max(srcALen, srcBLen) + 2*min(srcALen, srcBLen) - 2. - * @param[in] pScratch2 points to scratch buffer of size min(srcALen, srcBLen). - * @return Returns either ARM_MATH_SUCCESS if the function completed correctly or ARM_MATH_ARGUMENT_ERROR if the requested subset is not in the range [0 srcALen+srcBLen-2]. - */ -arm_status arm_conv_partial_opt_q15( - q15_t* pSrcA, - uint32_t srcALen, - q15_t* pSrcB, - uint32_t srcBLen, - q15_t* pDst, - uint32_t firstIndex, - uint32_t numPoints, - q15_t* pScratch1, - q15_t* pScratch2); - - -/** - * @brief Partial convolution of Q15 sequences. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data - * @param[in] firstIndex is the first output sample to start with. - * @param[in] numPoints is the number of output points to be computed. - * @return Returns either ARM_MATH_SUCCESS if the function completed correctly or ARM_MATH_ARGUMENT_ERROR if the requested subset is not in the range [0 srcALen+srcBLen-2]. - */ -arm_status arm_conv_partial_q15( - q15_t* pSrcA, - uint32_t srcALen, - q15_t* pSrcB, - uint32_t srcBLen, - q15_t* pDst, - uint32_t firstIndex, - uint32_t numPoints); - - -/** - * @brief Partial convolution of Q15 sequences (fast version) for Cortex-M3 and Cortex-M4 - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data - * @param[in] firstIndex is the first output sample to start with. - * @param[in] numPoints is the number of output points to be computed. - * @return Returns either ARM_MATH_SUCCESS if the function completed correctly or ARM_MATH_ARGUMENT_ERROR if the requested subset is not in the range [0 srcALen+srcBLen-2]. - */ -arm_status arm_conv_partial_fast_q15( - q15_t* pSrcA, - uint32_t srcALen, - q15_t* pSrcB, - uint32_t srcBLen, - q15_t* pDst, - uint32_t firstIndex, - uint32_t numPoints); - - -/** - * @brief Partial convolution of Q15 sequences (fast version) for Cortex-M3 and Cortex-M4 - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data - * @param[in] firstIndex is the first output sample to start with. - * @param[in] numPoints is the number of output points to be computed. - * @param[in] pScratch1 points to scratch buffer of size max(srcALen, srcBLen) + 2*min(srcALen, srcBLen) - 2. - * @param[in] pScratch2 points to scratch buffer of size min(srcALen, srcBLen). - * @return Returns either ARM_MATH_SUCCESS if the function completed correctly or ARM_MATH_ARGUMENT_ERROR if the requested subset is not in the range [0 srcALen+srcBLen-2]. - */ -arm_status arm_conv_partial_fast_opt_q15( - q15_t* pSrcA, - uint32_t srcALen, - q15_t* pSrcB, - uint32_t srcBLen, - q15_t* pDst, - uint32_t firstIndex, - uint32_t numPoints, - q15_t* pScratch1, - q15_t* pScratch2); - - -/** - * @brief Partial convolution of Q31 sequences. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data - * @param[in] firstIndex is the first output sample to start with. - * @param[in] numPoints is the number of output points to be computed. - * @return Returns either ARM_MATH_SUCCESS if the function completed correctly or ARM_MATH_ARGUMENT_ERROR if the requested subset is not in the range [0 srcALen+srcBLen-2]. - */ -arm_status arm_conv_partial_q31( - q31_t* pSrcA, - uint32_t srcALen, - q31_t* pSrcB, - uint32_t srcBLen, - q31_t* pDst, - uint32_t firstIndex, - uint32_t numPoints); - - -/** - * @brief Partial convolution of Q31 sequences (fast version) for Cortex-M3 and Cortex-M4 - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data - * @param[in] firstIndex is the first output sample to start with. - * @param[in] numPoints is the number of output points to be computed. - * @return Returns either ARM_MATH_SUCCESS if the function completed correctly or ARM_MATH_ARGUMENT_ERROR if the requested subset is not in the range [0 srcALen+srcBLen-2]. - */ -arm_status arm_conv_partial_fast_q31( - q31_t* pSrcA, - uint32_t srcALen, - q31_t* pSrcB, - uint32_t srcBLen, - q31_t* pDst, - uint32_t firstIndex, - uint32_t numPoints); - - -/** - * @brief Partial convolution of Q7 sequences - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data - * @param[in] firstIndex is the first output sample to start with. - * @param[in] numPoints is the number of output points to be computed. - * @param[in] pScratch1 points to scratch buffer(of type q15_t) of size max(srcALen, srcBLen) + 2*min(srcALen, srcBLen) - 2. - * @param[in] pScratch2 points to scratch buffer (of type q15_t) of size min(srcALen, srcBLen). - * @return Returns either ARM_MATH_SUCCESS if the function completed correctly or ARM_MATH_ARGUMENT_ERROR if the requested subset is not in the range [0 srcALen+srcBLen-2]. - */ -arm_status arm_conv_partial_opt_q7( - q7_t* pSrcA, - uint32_t srcALen, - q7_t* pSrcB, - uint32_t srcBLen, - q7_t* pDst, - uint32_t firstIndex, - uint32_t numPoints, - q15_t* pScratch1, - q15_t* pScratch2); - - -/** - * @brief Partial convolution of Q7 sequences. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data - * @param[in] firstIndex is the first output sample to start with. - * @param[in] numPoints is the number of output points to be computed. - * @return Returns either ARM_MATH_SUCCESS if the function completed correctly or ARM_MATH_ARGUMENT_ERROR if the requested subset is not in the range [0 srcALen+srcBLen-2]. - */ -arm_status arm_conv_partial_q7( - q7_t* pSrcA, - uint32_t srcALen, - q7_t* pSrcB, - uint32_t srcBLen, - q7_t* pDst, - uint32_t firstIndex, - uint32_t numPoints); - - -/** - * @brief Instance structure for the Q15 FIR decimator. - */ -typedef struct -{ - uint8_t M; /**< decimation factor. */ - uint16_t numTaps; /**< number of coefficients in the filter. */ - q15_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps.*/ - q15_t* pState; /**< points to the state variable array. The array is of length numTaps+blockSize-1. */ -} arm_fir_decimate_instance_q15; - -/** - * @brief Instance structure for the Q31 FIR decimator. - */ -typedef struct -{ - uint8_t M; /**< decimation factor. */ - uint16_t numTaps; /**< number of coefficients in the filter. */ - q31_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps.*/ - q31_t* pState; /**< points to the state variable array. The array is of length numTaps+blockSize-1. */ -} arm_fir_decimate_instance_q31; - -/** - * @brief Instance structure for the floating-point FIR decimator. - */ -typedef struct -{ - uint8_t M; /**< decimation factor. */ - uint16_t numTaps; /**< number of coefficients in the filter. */ - float32_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps.*/ - float32_t* pState; /**< points to the state variable array. The array is of length numTaps+blockSize-1. */ -} arm_fir_decimate_instance_f32; - - -/** - * @brief Processing function for the floating-point FIR decimator. - * @param[in] S points to an instance of the floating-point FIR decimator structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data - * @param[in] blockSize number of input samples to process per call. - */ -void arm_fir_decimate_f32( - const arm_fir_decimate_instance_f32* S, - float32_t* pSrc, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the floating-point FIR decimator. - * @param[in,out] S points to an instance of the floating-point FIR decimator structure. - * @param[in] numTaps number of coefficients in the filter. - * @param[in] M decimation factor. - * @param[in] pCoeffs points to the filter coefficients. - * @param[in] pState points to the state buffer. - * @param[in] blockSize number of input samples to process per call. - * @return The function returns ARM_MATH_SUCCESS if initialization is successful or ARM_MATH_LENGTH_ERROR if - * blockSize is not a multiple of M. - */ -arm_status arm_fir_decimate_init_f32( - arm_fir_decimate_instance_f32* S, - uint16_t numTaps, - uint8_t M, - float32_t* pCoeffs, - float32_t* pState, - uint32_t blockSize); - - -/** - * @brief Processing function for the Q15 FIR decimator. - * @param[in] S points to an instance of the Q15 FIR decimator structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data - * @param[in] blockSize number of input samples to process per call. - */ -void arm_fir_decimate_q15( - const arm_fir_decimate_instance_q15* S, - q15_t* pSrc, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Processing function for the Q15 FIR decimator (fast variant) for Cortex-M3 and Cortex-M4. - * @param[in] S points to an instance of the Q15 FIR decimator structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data - * @param[in] blockSize number of input samples to process per call. - */ -void arm_fir_decimate_fast_q15( - const arm_fir_decimate_instance_q15* S, - q15_t* pSrc, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the Q15 FIR decimator. - * @param[in,out] S points to an instance of the Q15 FIR decimator structure. - * @param[in] numTaps number of coefficients in the filter. - * @param[in] M decimation factor. - * @param[in] pCoeffs points to the filter coefficients. - * @param[in] pState points to the state buffer. - * @param[in] blockSize number of input samples to process per call. - * @return The function returns ARM_MATH_SUCCESS if initialization is successful or ARM_MATH_LENGTH_ERROR if - * blockSize is not a multiple of M. - */ -arm_status arm_fir_decimate_init_q15( - arm_fir_decimate_instance_q15* S, - uint16_t numTaps, - uint8_t M, - q15_t* pCoeffs, - q15_t* pState, - uint32_t blockSize); - - -/** - * @brief Processing function for the Q31 FIR decimator. - * @param[in] S points to an instance of the Q31 FIR decimator structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data - * @param[in] blockSize number of input samples to process per call. - */ -void arm_fir_decimate_q31( - const arm_fir_decimate_instance_q31* S, - q31_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - -/** - * @brief Processing function for the Q31 FIR decimator (fast variant) for Cortex-M3 and Cortex-M4. - * @param[in] S points to an instance of the Q31 FIR decimator structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data - * @param[in] blockSize number of input samples to process per call. - */ -void arm_fir_decimate_fast_q31( - arm_fir_decimate_instance_q31* S, - q31_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the Q31 FIR decimator. - * @param[in,out] S points to an instance of the Q31 FIR decimator structure. - * @param[in] numTaps number of coefficients in the filter. - * @param[in] M decimation factor. - * @param[in] pCoeffs points to the filter coefficients. - * @param[in] pState points to the state buffer. - * @param[in] blockSize number of input samples to process per call. - * @return The function returns ARM_MATH_SUCCESS if initialization is successful or ARM_MATH_LENGTH_ERROR if - * blockSize is not a multiple of M. - */ -arm_status arm_fir_decimate_init_q31( - arm_fir_decimate_instance_q31* S, - uint16_t numTaps, - uint8_t M, - q31_t* pCoeffs, - q31_t* pState, - uint32_t blockSize); - - -/** - * @brief Instance structure for the Q15 FIR interpolator. - */ -typedef struct -{ - uint8_t L; /**< upsample factor. */ - uint16_t phaseLength; /**< length of each polyphase filter component. */ - q15_t* pCoeffs; /**< points to the coefficient array. The array is of length L*phaseLength. */ - q15_t* pState; /**< points to the state variable array. The array is of length blockSize+phaseLength-1. */ -} arm_fir_interpolate_instance_q15; - -/** - * @brief Instance structure for the Q31 FIR interpolator. - */ -typedef struct -{ - uint8_t L; /**< upsample factor. */ - uint16_t phaseLength; /**< length of each polyphase filter component. */ - q31_t* pCoeffs; /**< points to the coefficient array. The array is of length L*phaseLength. */ - q31_t* pState; /**< points to the state variable array. The array is of length blockSize+phaseLength-1. */ -} arm_fir_interpolate_instance_q31; - -/** - * @brief Instance structure for the floating-point FIR interpolator. - */ -typedef struct -{ - uint8_t L; /**< upsample factor. */ - uint16_t phaseLength; /**< length of each polyphase filter component. */ - float32_t* pCoeffs; /**< points to the coefficient array. The array is of length L*phaseLength. */ - float32_t* pState; /**< points to the state variable array. The array is of length phaseLength+numTaps-1. */ -} arm_fir_interpolate_instance_f32; - - -/** - * @brief Processing function for the Q15 FIR interpolator. - * @param[in] S points to an instance of the Q15 FIR interpolator structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of input samples to process per call. - */ -void arm_fir_interpolate_q15( - const arm_fir_interpolate_instance_q15* S, - q15_t* pSrc, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the Q15 FIR interpolator. - * @param[in,out] S points to an instance of the Q15 FIR interpolator structure. - * @param[in] L upsample factor. - * @param[in] numTaps number of filter coefficients in the filter. - * @param[in] pCoeffs points to the filter coefficient buffer. - * @param[in] pState points to the state buffer. - * @param[in] blockSize number of input samples to process per call. - * @return The function returns ARM_MATH_SUCCESS if initialization is successful or ARM_MATH_LENGTH_ERROR if - * the filter length numTaps is not a multiple of the interpolation factor L. - */ -arm_status arm_fir_interpolate_init_q15( - arm_fir_interpolate_instance_q15* S, - uint8_t L, - uint16_t numTaps, - q15_t* pCoeffs, - q15_t* pState, - uint32_t blockSize); - - -/** - * @brief Processing function for the Q31 FIR interpolator. - * @param[in] S points to an instance of the Q15 FIR interpolator structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of input samples to process per call. - */ -void arm_fir_interpolate_q31( - const arm_fir_interpolate_instance_q31* S, - q31_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the Q31 FIR interpolator. - * @param[in,out] S points to an instance of the Q31 FIR interpolator structure. - * @param[in] L upsample factor. - * @param[in] numTaps number of filter coefficients in the filter. - * @param[in] pCoeffs points to the filter coefficient buffer. - * @param[in] pState points to the state buffer. - * @param[in] blockSize number of input samples to process per call. - * @return The function returns ARM_MATH_SUCCESS if initialization is successful or ARM_MATH_LENGTH_ERROR if - * the filter length numTaps is not a multiple of the interpolation factor L. - */ -arm_status arm_fir_interpolate_init_q31( - arm_fir_interpolate_instance_q31* S, - uint8_t L, - uint16_t numTaps, - q31_t* pCoeffs, - q31_t* pState, - uint32_t blockSize); - - -/** - * @brief Processing function for the floating-point FIR interpolator. - * @param[in] S points to an instance of the floating-point FIR interpolator structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of input samples to process per call. - */ -void arm_fir_interpolate_f32( - const arm_fir_interpolate_instance_f32* S, - float32_t* pSrc, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the floating-point FIR interpolator. - * @param[in,out] S points to an instance of the floating-point FIR interpolator structure. - * @param[in] L upsample factor. - * @param[in] numTaps number of filter coefficients in the filter. - * @param[in] pCoeffs points to the filter coefficient buffer. - * @param[in] pState points to the state buffer. - * @param[in] blockSize number of input samples to process per call. - * @return The function returns ARM_MATH_SUCCESS if initialization is successful or ARM_MATH_LENGTH_ERROR if - * the filter length numTaps is not a multiple of the interpolation factor L. - */ -arm_status arm_fir_interpolate_init_f32( - arm_fir_interpolate_instance_f32* S, - uint8_t L, - uint16_t numTaps, - float32_t* pCoeffs, - float32_t* pState, - uint32_t blockSize); - - -/** - * @brief Instance structure for the high precision Q31 Biquad cascade filter. - */ -typedef struct -{ - uint8_t numStages; /**< number of 2nd order stages in the filter. Overall order is 2*numStages. */ - q63_t* pState; /**< points to the array of state coefficients. The array is of length 4*numStages. */ - q31_t* pCoeffs; /**< points to the array of coefficients. The array is of length 5*numStages. */ - uint8_t postShift; /**< additional shift, in bits, applied to each output sample. */ -} arm_biquad_cas_df1_32x64_ins_q31; - - -/** - * @param[in] S points to an instance of the high precision Q31 Biquad cascade filter structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data - * @param[in] blockSize number of samples to process. - */ -void arm_biquad_cas_df1_32x64_q31( - const arm_biquad_cas_df1_32x64_ins_q31* S, - q31_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @param[in,out] S points to an instance of the high precision Q31 Biquad cascade filter structure. - * @param[in] numStages number of 2nd order stages in the filter. - * @param[in] pCoeffs points to the filter coefficients. - * @param[in] pState points to the state buffer. - * @param[in] postShift shift to be applied to the output. Varies according to the coefficients format - */ -void arm_biquad_cas_df1_32x64_init_q31( - arm_biquad_cas_df1_32x64_ins_q31* S, - uint8_t numStages, - q31_t* pCoeffs, - q63_t* pState, - uint8_t postShift); - - -/** - * @brief Instance structure for the floating-point transposed direct form II Biquad cascade filter. - */ -typedef struct -{ - uint8_t numStages; /**< number of 2nd order stages in the filter. Overall order is 2*numStages. */ - float32_t* pState; /**< points to the array of state coefficients. The array is of length 2*numStages. */ - float32_t* pCoeffs; /**< points to the array of coefficients. The array is of length 5*numStages. */ -} arm_biquad_cascade_df2T_instance_f32; - -/** - * @brief Instance structure for the floating-point transposed direct form II Biquad cascade filter. - */ -typedef struct -{ - uint8_t numStages; /**< number of 2nd order stages in the filter. Overall order is 2*numStages. */ - float32_t* pState; /**< points to the array of state coefficients. The array is of length 4*numStages. */ - float32_t* pCoeffs; /**< points to the array of coefficients. The array is of length 5*numStages. */ -} arm_biquad_cascade_stereo_df2T_instance_f32; - -/** - * @brief Instance structure for the floating-point transposed direct form II Biquad cascade filter. - */ -typedef struct -{ - uint8_t numStages; /**< number of 2nd order stages in the filter. Overall order is 2*numStages. */ - float64_t* pState; /**< points to the array of state coefficients. The array is of length 2*numStages. */ - float64_t* pCoeffs; /**< points to the array of coefficients. The array is of length 5*numStages. */ -} arm_biquad_cascade_df2T_instance_f64; - - -/** - * @brief Processing function for the floating-point transposed direct form II Biquad cascade filter. - * @param[in] S points to an instance of the filter data structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data - * @param[in] blockSize number of samples to process. - */ -void arm_biquad_cascade_df2T_f32( - const arm_biquad_cascade_df2T_instance_f32* S, - float32_t* pSrc, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Processing function for the floating-point transposed direct form II Biquad cascade filter. 2 channels - * @param[in] S points to an instance of the filter data structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data - * @param[in] blockSize number of samples to process. - */ -void arm_biquad_cascade_stereo_df2T_f32( - const arm_biquad_cascade_stereo_df2T_instance_f32* S, - float32_t* pSrc, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Processing function for the floating-point transposed direct form II Biquad cascade filter. - * @param[in] S points to an instance of the filter data structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data - * @param[in] blockSize number of samples to process. - */ -void arm_biquad_cascade_df2T_f64( - const arm_biquad_cascade_df2T_instance_f64* S, - float64_t* pSrc, - float64_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the floating-point transposed direct form II Biquad cascade filter. - * @param[in,out] S points to an instance of the filter data structure. - * @param[in] numStages number of 2nd order stages in the filter. - * @param[in] pCoeffs points to the filter coefficients. - * @param[in] pState points to the state buffer. - */ -void arm_biquad_cascade_df2T_init_f32( - arm_biquad_cascade_df2T_instance_f32* S, - uint8_t numStages, - float32_t* pCoeffs, - float32_t* pState); - - -/** - * @brief Initialization function for the floating-point transposed direct form II Biquad cascade filter. - * @param[in,out] S points to an instance of the filter data structure. - * @param[in] numStages number of 2nd order stages in the filter. - * @param[in] pCoeffs points to the filter coefficients. - * @param[in] pState points to the state buffer. - */ -void arm_biquad_cascade_stereo_df2T_init_f32( - arm_biquad_cascade_stereo_df2T_instance_f32* S, - uint8_t numStages, - float32_t* pCoeffs, - float32_t* pState); - - -/** - * @brief Initialization function for the floating-point transposed direct form II Biquad cascade filter. - * @param[in,out] S points to an instance of the filter data structure. - * @param[in] numStages number of 2nd order stages in the filter. - * @param[in] pCoeffs points to the filter coefficients. - * @param[in] pState points to the state buffer. - */ -void arm_biquad_cascade_df2T_init_f64( - arm_biquad_cascade_df2T_instance_f64* S, - uint8_t numStages, - float64_t* pCoeffs, - float64_t* pState); - - -/** - * @brief Instance structure for the Q15 FIR lattice filter. - */ -typedef struct -{ - uint16_t numStages; /**< number of filter stages. */ - q15_t* pState; /**< points to the state variable array. The array is of length numStages. */ - q15_t* pCoeffs; /**< points to the coefficient array. The array is of length numStages. */ -} arm_fir_lattice_instance_q15; - -/** - * @brief Instance structure for the Q31 FIR lattice filter. - */ -typedef struct -{ - uint16_t numStages; /**< number of filter stages. */ - q31_t* pState; /**< points to the state variable array. The array is of length numStages. */ - q31_t* pCoeffs; /**< points to the coefficient array. The array is of length numStages. */ -} arm_fir_lattice_instance_q31; - -/** - * @brief Instance structure for the floating-point FIR lattice filter. - */ -typedef struct -{ - uint16_t numStages; /**< number of filter stages. */ - float32_t* pState; /**< points to the state variable array. The array is of length numStages. */ - float32_t* pCoeffs; /**< points to the coefficient array. The array is of length numStages. */ -} arm_fir_lattice_instance_f32; - - -/** - * @brief Initialization function for the Q15 FIR lattice filter. - * @param[in] S points to an instance of the Q15 FIR lattice structure. - * @param[in] numStages number of filter stages. - * @param[in] pCoeffs points to the coefficient buffer. The array is of length numStages. - * @param[in] pState points to the state buffer. The array is of length numStages. - */ -void arm_fir_lattice_init_q15( - arm_fir_lattice_instance_q15* S, - uint16_t numStages, - q15_t* pCoeffs, - q15_t* pState); - - -/** - * @brief Processing function for the Q15 FIR lattice filter. - * @param[in] S points to an instance of the Q15 FIR lattice structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of samples to process. - */ -void arm_fir_lattice_q15( - const arm_fir_lattice_instance_q15* S, - q15_t* pSrc, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the Q31 FIR lattice filter. - * @param[in] S points to an instance of the Q31 FIR lattice structure. - * @param[in] numStages number of filter stages. - * @param[in] pCoeffs points to the coefficient buffer. The array is of length numStages. - * @param[in] pState points to the state buffer. The array is of length numStages. - */ -void arm_fir_lattice_init_q31( - arm_fir_lattice_instance_q31* S, - uint16_t numStages, - q31_t* pCoeffs, - q31_t* pState); - - -/** - * @brief Processing function for the Q31 FIR lattice filter. - * @param[in] S points to an instance of the Q31 FIR lattice structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data - * @param[in] blockSize number of samples to process. - */ -void arm_fir_lattice_q31( - const arm_fir_lattice_instance_q31* S, - q31_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the floating-point FIR lattice filter. - * @param[in] S points to an instance of the floating-point FIR lattice structure. - * @param[in] numStages number of filter stages. - * @param[in] pCoeffs points to the coefficient buffer. The array is of length numStages. - * @param[in] pState points to the state buffer. The array is of length numStages. - */ -void arm_fir_lattice_init_f32( - arm_fir_lattice_instance_f32* S, - uint16_t numStages, - float32_t* pCoeffs, - float32_t* pState); - - -/** - * @brief Processing function for the floating-point FIR lattice filter. - * @param[in] S points to an instance of the floating-point FIR lattice structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data - * @param[in] blockSize number of samples to process. - */ -void arm_fir_lattice_f32( - const arm_fir_lattice_instance_f32* S, - float32_t* pSrc, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Instance structure for the Q15 IIR lattice filter. - */ -typedef struct -{ - uint16_t numStages; /**< number of stages in the filter. */ - q15_t* pState; /**< points to the state variable array. The array is of length numStages+blockSize. */ - q15_t* pkCoeffs; /**< points to the reflection coefficient array. The array is of length numStages. */ - q15_t* pvCoeffs; /**< points to the ladder coefficient array. The array is of length numStages+1. */ -} arm_iir_lattice_instance_q15; - -/** - * @brief Instance structure for the Q31 IIR lattice filter. - */ -typedef struct -{ - uint16_t numStages; /**< number of stages in the filter. */ - q31_t* pState; /**< points to the state variable array. The array is of length numStages+blockSize. */ - q31_t* pkCoeffs; /**< points to the reflection coefficient array. The array is of length numStages. */ - q31_t* pvCoeffs; /**< points to the ladder coefficient array. The array is of length numStages+1. */ -} arm_iir_lattice_instance_q31; - -/** - * @brief Instance structure for the floating-point IIR lattice filter. - */ -typedef struct -{ - uint16_t numStages; /**< number of stages in the filter. */ - float32_t* pState; /**< points to the state variable array. The array is of length numStages+blockSize. */ - float32_t* pkCoeffs; /**< points to the reflection coefficient array. The array is of length numStages. */ - float32_t* pvCoeffs; /**< points to the ladder coefficient array. The array is of length numStages+1. */ -} arm_iir_lattice_instance_f32; - - -/** - * @brief Processing function for the floating-point IIR lattice filter. - * @param[in] S points to an instance of the floating-point IIR lattice structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of samples to process. - */ -void arm_iir_lattice_f32( - const arm_iir_lattice_instance_f32* S, - float32_t* pSrc, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the floating-point IIR lattice filter. - * @param[in] S points to an instance of the floating-point IIR lattice structure. - * @param[in] numStages number of stages in the filter. - * @param[in] pkCoeffs points to the reflection coefficient buffer. The array is of length numStages. - * @param[in] pvCoeffs points to the ladder coefficient buffer. The array is of length numStages+1. - * @param[in] pState points to the state buffer. The array is of length numStages+blockSize-1. - * @param[in] blockSize number of samples to process. - */ -void arm_iir_lattice_init_f32( - arm_iir_lattice_instance_f32* S, - uint16_t numStages, - float32_t* pkCoeffs, - float32_t* pvCoeffs, - float32_t* pState, - uint32_t blockSize); - - -/** - * @brief Processing function for the Q31 IIR lattice filter. - * @param[in] S points to an instance of the Q31 IIR lattice structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of samples to process. - */ -void arm_iir_lattice_q31( - const arm_iir_lattice_instance_q31* S, - q31_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the Q31 IIR lattice filter. - * @param[in] S points to an instance of the Q31 IIR lattice structure. - * @param[in] numStages number of stages in the filter. - * @param[in] pkCoeffs points to the reflection coefficient buffer. The array is of length numStages. - * @param[in] pvCoeffs points to the ladder coefficient buffer. The array is of length numStages+1. - * @param[in] pState points to the state buffer. The array is of length numStages+blockSize. - * @param[in] blockSize number of samples to process. - */ -void arm_iir_lattice_init_q31( - arm_iir_lattice_instance_q31* S, - uint16_t numStages, - q31_t* pkCoeffs, - q31_t* pvCoeffs, - q31_t* pState, - uint32_t blockSize); - - -/** - * @brief Processing function for the Q15 IIR lattice filter. - * @param[in] S points to an instance of the Q15 IIR lattice structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data. - * @param[in] blockSize number of samples to process. - */ -void arm_iir_lattice_q15( - const arm_iir_lattice_instance_q15* S, - q15_t* pSrc, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Initialization function for the Q15 IIR lattice filter. - * @param[in] S points to an instance of the fixed-point Q15 IIR lattice structure. - * @param[in] numStages number of stages in the filter. - * @param[in] pkCoeffs points to reflection coefficient buffer. The array is of length numStages. - * @param[in] pvCoeffs points to ladder coefficient buffer. The array is of length numStages+1. - * @param[in] pState points to state buffer. The array is of length numStages+blockSize. - * @param[in] blockSize number of samples to process per call. - */ -void arm_iir_lattice_init_q15( - arm_iir_lattice_instance_q15* S, - uint16_t numStages, - q15_t* pkCoeffs, - q15_t* pvCoeffs, - q15_t* pState, - uint32_t blockSize); - - -/** - * @brief Instance structure for the floating-point LMS filter. - */ -typedef struct -{ - uint16_t numTaps; /**< number of coefficients in the filter. */ - float32_t* pState; /**< points to the state variable array. The array is of length numTaps+blockSize-1. */ - float32_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps. */ - float32_t mu; /**< step size that controls filter coefficient updates. */ -} arm_lms_instance_f32; - - -/** - * @brief Processing function for floating-point LMS filter. - * @param[in] S points to an instance of the floating-point LMS filter structure. - * @param[in] pSrc points to the block of input data. - * @param[in] pRef points to the block of reference data. - * @param[out] pOut points to the block of output data. - * @param[out] pErr points to the block of error data. - * @param[in] blockSize number of samples to process. - */ -void arm_lms_f32( - const arm_lms_instance_f32* S, - float32_t* pSrc, - float32_t* pRef, - float32_t* pOut, - float32_t* pErr, - uint32_t blockSize); - - -/** - * @brief Initialization function for floating-point LMS filter. - * @param[in] S points to an instance of the floating-point LMS filter structure. - * @param[in] numTaps number of filter coefficients. - * @param[in] pCoeffs points to the coefficient buffer. - * @param[in] pState points to state buffer. - * @param[in] mu step size that controls filter coefficient updates. - * @param[in] blockSize number of samples to process. - */ -void arm_lms_init_f32( - arm_lms_instance_f32* S, - uint16_t numTaps, - float32_t* pCoeffs, - float32_t* pState, - float32_t mu, - uint32_t blockSize); - - -/** - * @brief Instance structure for the Q15 LMS filter. - */ -typedef struct -{ - uint16_t numTaps; /**< number of coefficients in the filter. */ - q15_t* pState; /**< points to the state variable array. The array is of length numTaps+blockSize-1. */ - q15_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps. */ - q15_t mu; /**< step size that controls filter coefficient updates. */ - uint32_t postShift; /**< bit shift applied to coefficients. */ -} arm_lms_instance_q15; - - -/** - * @brief Initialization function for the Q15 LMS filter. - * @param[in] S points to an instance of the Q15 LMS filter structure. - * @param[in] numTaps number of filter coefficients. - * @param[in] pCoeffs points to the coefficient buffer. - * @param[in] pState points to the state buffer. - * @param[in] mu step size that controls filter coefficient updates. - * @param[in] blockSize number of samples to process. - * @param[in] postShift bit shift applied to coefficients. - */ -void arm_lms_init_q15( - arm_lms_instance_q15* S, - uint16_t numTaps, - q15_t* pCoeffs, - q15_t* pState, - q15_t mu, - uint32_t blockSize, - uint32_t postShift); - - -/** - * @brief Processing function for Q15 LMS filter. - * @param[in] S points to an instance of the Q15 LMS filter structure. - * @param[in] pSrc points to the block of input data. - * @param[in] pRef points to the block of reference data. - * @param[out] pOut points to the block of output data. - * @param[out] pErr points to the block of error data. - * @param[in] blockSize number of samples to process. - */ -void arm_lms_q15( - const arm_lms_instance_q15* S, - q15_t* pSrc, - q15_t* pRef, - q15_t* pOut, - q15_t* pErr, - uint32_t blockSize); - - -/** - * @brief Instance structure for the Q31 LMS filter. - */ -typedef struct -{ - uint16_t numTaps; /**< number of coefficients in the filter. */ - q31_t* pState; /**< points to the state variable array. The array is of length numTaps+blockSize-1. */ - q31_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps. */ - q31_t mu; /**< step size that controls filter coefficient updates. */ - uint32_t postShift; /**< bit shift applied to coefficients. */ -} arm_lms_instance_q31; - - -/** - * @brief Processing function for Q31 LMS filter. - * @param[in] S points to an instance of the Q15 LMS filter structure. - * @param[in] pSrc points to the block of input data. - * @param[in] pRef points to the block of reference data. - * @param[out] pOut points to the block of output data. - * @param[out] pErr points to the block of error data. - * @param[in] blockSize number of samples to process. - */ -void arm_lms_q31( - const arm_lms_instance_q31* S, - q31_t* pSrc, - q31_t* pRef, - q31_t* pOut, - q31_t* pErr, - uint32_t blockSize); - - -/** - * @brief Initialization function for Q31 LMS filter. - * @param[in] S points to an instance of the Q31 LMS filter structure. - * @param[in] numTaps number of filter coefficients. - * @param[in] pCoeffs points to coefficient buffer. - * @param[in] pState points to state buffer. - * @param[in] mu step size that controls filter coefficient updates. - * @param[in] blockSize number of samples to process. - * @param[in] postShift bit shift applied to coefficients. - */ -void arm_lms_init_q31( - arm_lms_instance_q31* S, - uint16_t numTaps, - q31_t* pCoeffs, - q31_t* pState, - q31_t mu, - uint32_t blockSize, - uint32_t postShift); - - -/** - * @brief Instance structure for the floating-point normalized LMS filter. - */ -typedef struct -{ - uint16_t numTaps; /**< number of coefficients in the filter. */ - float32_t* pState; /**< points to the state variable array. The array is of length numTaps+blockSize-1. */ - float32_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps. */ - float32_t mu; /**< step size that control filter coefficient updates. */ - float32_t energy; /**< saves previous frame energy. */ - float32_t x0; /**< saves previous input sample. */ -} arm_lms_norm_instance_f32; - - -/** - * @brief Processing function for floating-point normalized LMS filter. - * @param[in] S points to an instance of the floating-point normalized LMS filter structure. - * @param[in] pSrc points to the block of input data. - * @param[in] pRef points to the block of reference data. - * @param[out] pOut points to the block of output data. - * @param[out] pErr points to the block of error data. - * @param[in] blockSize number of samples to process. - */ -void arm_lms_norm_f32( - arm_lms_norm_instance_f32* S, - float32_t* pSrc, - float32_t* pRef, - float32_t* pOut, - float32_t* pErr, - uint32_t blockSize); - - -/** - * @brief Initialization function for floating-point normalized LMS filter. - * @param[in] S points to an instance of the floating-point LMS filter structure. - * @param[in] numTaps number of filter coefficients. - * @param[in] pCoeffs points to coefficient buffer. - * @param[in] pState points to state buffer. - * @param[in] mu step size that controls filter coefficient updates. - * @param[in] blockSize number of samples to process. - */ -void arm_lms_norm_init_f32( - arm_lms_norm_instance_f32* S, - uint16_t numTaps, - float32_t* pCoeffs, - float32_t* pState, - float32_t mu, - uint32_t blockSize); - - -/** - * @brief Instance structure for the Q31 normalized LMS filter. - */ -typedef struct -{ - uint16_t numTaps; /**< number of coefficients in the filter. */ - q31_t* pState; /**< points to the state variable array. The array is of length numTaps+blockSize-1. */ - q31_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps. */ - q31_t mu; /**< step size that controls filter coefficient updates. */ - uint8_t postShift; /**< bit shift applied to coefficients. */ - q31_t* recipTable; /**< points to the reciprocal initial value table. */ - q31_t energy; /**< saves previous frame energy. */ - q31_t x0; /**< saves previous input sample. */ -} arm_lms_norm_instance_q31; - - -/** - * @brief Processing function for Q31 normalized LMS filter. - * @param[in] S points to an instance of the Q31 normalized LMS filter structure. - * @param[in] pSrc points to the block of input data. - * @param[in] pRef points to the block of reference data. - * @param[out] pOut points to the block of output data. - * @param[out] pErr points to the block of error data. - * @param[in] blockSize number of samples to process. - */ -void arm_lms_norm_q31( - arm_lms_norm_instance_q31* S, - q31_t* pSrc, - q31_t* pRef, - q31_t* pOut, - q31_t* pErr, - uint32_t blockSize); - - -/** - * @brief Initialization function for Q31 normalized LMS filter. - * @param[in] S points to an instance of the Q31 normalized LMS filter structure. - * @param[in] numTaps number of filter coefficients. - * @param[in] pCoeffs points to coefficient buffer. - * @param[in] pState points to state buffer. - * @param[in] mu step size that controls filter coefficient updates. - * @param[in] blockSize number of samples to process. - * @param[in] postShift bit shift applied to coefficients. - */ -void arm_lms_norm_init_q31( - arm_lms_norm_instance_q31* S, - uint16_t numTaps, - q31_t* pCoeffs, - q31_t* pState, - q31_t mu, - uint32_t blockSize, - uint8_t postShift); - - -/** - * @brief Instance structure for the Q15 normalized LMS filter. - */ -typedef struct -{ - uint16_t numTaps; /**< Number of coefficients in the filter. */ - q15_t* pState; /**< points to the state variable array. The array is of length numTaps+blockSize-1. */ - q15_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps. */ - q15_t mu; /**< step size that controls filter coefficient updates. */ - uint8_t postShift; /**< bit shift applied to coefficients. */ - q15_t* recipTable; /**< Points to the reciprocal initial value table. */ - q15_t energy; /**< saves previous frame energy. */ - q15_t x0; /**< saves previous input sample. */ -} arm_lms_norm_instance_q15; - - -/** - * @brief Processing function for Q15 normalized LMS filter. - * @param[in] S points to an instance of the Q15 normalized LMS filter structure. - * @param[in] pSrc points to the block of input data. - * @param[in] pRef points to the block of reference data. - * @param[out] pOut points to the block of output data. - * @param[out] pErr points to the block of error data. - * @param[in] blockSize number of samples to process. - */ -void arm_lms_norm_q15( - arm_lms_norm_instance_q15* S, - q15_t* pSrc, - q15_t* pRef, - q15_t* pOut, - q15_t* pErr, - uint32_t blockSize); - - -/** - * @brief Initialization function for Q15 normalized LMS filter. - * @param[in] S points to an instance of the Q15 normalized LMS filter structure. - * @param[in] numTaps number of filter coefficients. - * @param[in] pCoeffs points to coefficient buffer. - * @param[in] pState points to state buffer. - * @param[in] mu step size that controls filter coefficient updates. - * @param[in] blockSize number of samples to process. - * @param[in] postShift bit shift applied to coefficients. - */ -void arm_lms_norm_init_q15( - arm_lms_norm_instance_q15* S, - uint16_t numTaps, - q15_t* pCoeffs, - q15_t* pState, - q15_t mu, - uint32_t blockSize, - uint8_t postShift); - - -/** - * @brief Correlation of floating-point sequences. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data Length 2 * max(srcALen, srcBLen) - 1. - */ -void arm_correlate_f32( - float32_t* pSrcA, - uint32_t srcALen, - float32_t* pSrcB, - uint32_t srcBLen, - float32_t* pDst); - - -/** -* @brief Correlation of Q15 sequences -* @param[in] pSrcA points to the first input sequence. -* @param[in] srcALen length of the first input sequence. -* @param[in] pSrcB points to the second input sequence. -* @param[in] srcBLen length of the second input sequence. -* @param[out] pDst points to the block of output data Length 2 * max(srcALen, srcBLen) - 1. -* @param[in] pScratch points to scratch buffer of size max(srcALen, srcBLen) + 2*min(srcALen, srcBLen) - 2. -*/ -void arm_correlate_opt_q15( - q15_t* pSrcA, - uint32_t srcALen, - q15_t* pSrcB, - uint32_t srcBLen, - q15_t* pDst, - q15_t* pScratch); - - -/** - * @brief Correlation of Q15 sequences. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data Length 2 * max(srcALen, srcBLen) - 1. - */ - -void arm_correlate_q15( - q15_t* pSrcA, - uint32_t srcALen, - q15_t* pSrcB, - uint32_t srcBLen, - q15_t* pDst); - - -/** - * @brief Correlation of Q15 sequences (fast version) for Cortex-M3 and Cortex-M4. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data Length 2 * max(srcALen, srcBLen) - 1. - */ - -void arm_correlate_fast_q15( - q15_t* pSrcA, - uint32_t srcALen, - q15_t* pSrcB, - uint32_t srcBLen, - q15_t* pDst); - - -/** - * @brief Correlation of Q15 sequences (fast version) for Cortex-M3 and Cortex-M4. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data Length 2 * max(srcALen, srcBLen) - 1. - * @param[in] pScratch points to scratch buffer of size max(srcALen, srcBLen) + 2*min(srcALen, srcBLen) - 2. - */ -void arm_correlate_fast_opt_q15( - q15_t* pSrcA, - uint32_t srcALen, - q15_t* pSrcB, - uint32_t srcBLen, - q15_t* pDst, - q15_t* pScratch); - - -/** - * @brief Correlation of Q31 sequences. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data Length 2 * max(srcALen, srcBLen) - 1. - */ -void arm_correlate_q31( - q31_t* pSrcA, - uint32_t srcALen, - q31_t* pSrcB, - uint32_t srcBLen, - q31_t* pDst); - - -/** - * @brief Correlation of Q31 sequences (fast version) for Cortex-M3 and Cortex-M4 - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data Length 2 * max(srcALen, srcBLen) - 1. - */ -void arm_correlate_fast_q31( - q31_t* pSrcA, - uint32_t srcALen, - q31_t* pSrcB, - uint32_t srcBLen, - q31_t* pDst); - - -/** - * @brief Correlation of Q7 sequences. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data Length 2 * max(srcALen, srcBLen) - 1. - * @param[in] pScratch1 points to scratch buffer(of type q15_t) of size max(srcALen, srcBLen) + 2*min(srcALen, srcBLen) - 2. - * @param[in] pScratch2 points to scratch buffer (of type q15_t) of size min(srcALen, srcBLen). - */ -void arm_correlate_opt_q7( - q7_t* pSrcA, - uint32_t srcALen, - q7_t* pSrcB, - uint32_t srcBLen, - q7_t* pDst, - q15_t* pScratch1, - q15_t* pScratch2); - - -/** - * @brief Correlation of Q7 sequences. - * @param[in] pSrcA points to the first input sequence. - * @param[in] srcALen length of the first input sequence. - * @param[in] pSrcB points to the second input sequence. - * @param[in] srcBLen length of the second input sequence. - * @param[out] pDst points to the block of output data Length 2 * max(srcALen, srcBLen) - 1. - */ -void arm_correlate_q7( - q7_t* pSrcA, - uint32_t srcALen, - q7_t* pSrcB, - uint32_t srcBLen, - q7_t* pDst); - - -/** - * @brief Instance structure for the floating-point sparse FIR filter. - */ -typedef struct -{ - uint16_t numTaps; /**< number of coefficients in the filter. */ - uint16_t stateIndex; /**< state buffer index. Points to the oldest sample in the state buffer. */ - float32_t* pState; /**< points to the state buffer array. The array is of length maxDelay+blockSize-1. */ - float32_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps.*/ - uint16_t maxDelay; /**< maximum offset specified by the pTapDelay array. */ - int32_t* pTapDelay; /**< points to the array of delay values. The array is of length numTaps. */ -} arm_fir_sparse_instance_f32; - -/** - * @brief Instance structure for the Q31 sparse FIR filter. - */ -typedef struct -{ - uint16_t numTaps; /**< number of coefficients in the filter. */ - uint16_t stateIndex; /**< state buffer index. Points to the oldest sample in the state buffer. */ - q31_t* pState; /**< points to the state buffer array. The array is of length maxDelay+blockSize-1. */ - q31_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps.*/ - uint16_t maxDelay; /**< maximum offset specified by the pTapDelay array. */ - int32_t* pTapDelay; /**< points to the array of delay values. The array is of length numTaps. */ -} arm_fir_sparse_instance_q31; - -/** - * @brief Instance structure for the Q15 sparse FIR filter. - */ -typedef struct -{ - uint16_t numTaps; /**< number of coefficients in the filter. */ - uint16_t stateIndex; /**< state buffer index. Points to the oldest sample in the state buffer. */ - q15_t* pState; /**< points to the state buffer array. The array is of length maxDelay+blockSize-1. */ - q15_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps.*/ - uint16_t maxDelay; /**< maximum offset specified by the pTapDelay array. */ - int32_t* pTapDelay; /**< points to the array of delay values. The array is of length numTaps. */ -} arm_fir_sparse_instance_q15; - -/** - * @brief Instance structure for the Q7 sparse FIR filter. - */ -typedef struct -{ - uint16_t numTaps; /**< number of coefficients in the filter. */ - uint16_t stateIndex; /**< state buffer index. Points to the oldest sample in the state buffer. */ - q7_t* pState; /**< points to the state buffer array. The array is of length maxDelay+blockSize-1. */ - q7_t* pCoeffs; /**< points to the coefficient array. The array is of length numTaps.*/ - uint16_t maxDelay; /**< maximum offset specified by the pTapDelay array. */ - int32_t* pTapDelay; /**< points to the array of delay values. The array is of length numTaps. */ -} arm_fir_sparse_instance_q7; - - -/** - * @brief Processing function for the floating-point sparse FIR filter. - * @param[in] S points to an instance of the floating-point sparse FIR structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data - * @param[in] pScratchIn points to a temporary buffer of size blockSize. - * @param[in] blockSize number of input samples to process per call. - */ -void arm_fir_sparse_f32( - arm_fir_sparse_instance_f32* S, - float32_t* pSrc, - float32_t* pDst, - float32_t* pScratchIn, - uint32_t blockSize); - - -/** - * @brief Initialization function for the floating-point sparse FIR filter. - * @param[in,out] S points to an instance of the floating-point sparse FIR structure. - * @param[in] numTaps number of nonzero coefficients in the filter. - * @param[in] pCoeffs points to the array of filter coefficients. - * @param[in] pState points to the state buffer. - * @param[in] pTapDelay points to the array of offset times. - * @param[in] maxDelay maximum offset time supported. - * @param[in] blockSize number of samples that will be processed per block. - */ -void arm_fir_sparse_init_f32( - arm_fir_sparse_instance_f32* S, - uint16_t numTaps, - float32_t* pCoeffs, - float32_t* pState, - int32_t* pTapDelay, - uint16_t maxDelay, - uint32_t blockSize); - - -/** - * @brief Processing function for the Q31 sparse FIR filter. - * @param[in] S points to an instance of the Q31 sparse FIR structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data - * @param[in] pScratchIn points to a temporary buffer of size blockSize. - * @param[in] blockSize number of input samples to process per call. - */ -void arm_fir_sparse_q31( - arm_fir_sparse_instance_q31* S, - q31_t* pSrc, - q31_t* pDst, - q31_t* pScratchIn, - uint32_t blockSize); - - -/** - * @brief Initialization function for the Q31 sparse FIR filter. - * @param[in,out] S points to an instance of the Q31 sparse FIR structure. - * @param[in] numTaps number of nonzero coefficients in the filter. - * @param[in] pCoeffs points to the array of filter coefficients. - * @param[in] pState points to the state buffer. - * @param[in] pTapDelay points to the array of offset times. - * @param[in] maxDelay maximum offset time supported. - * @param[in] blockSize number of samples that will be processed per block. - */ -void arm_fir_sparse_init_q31( - arm_fir_sparse_instance_q31* S, - uint16_t numTaps, - q31_t* pCoeffs, - q31_t* pState, - int32_t* pTapDelay, - uint16_t maxDelay, - uint32_t blockSize); - - -/** - * @brief Processing function for the Q15 sparse FIR filter. - * @param[in] S points to an instance of the Q15 sparse FIR structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data - * @param[in] pScratchIn points to a temporary buffer of size blockSize. - * @param[in] pScratchOut points to a temporary buffer of size blockSize. - * @param[in] blockSize number of input samples to process per call. - */ -void arm_fir_sparse_q15( - arm_fir_sparse_instance_q15* S, - q15_t* pSrc, - q15_t* pDst, - q15_t* pScratchIn, - q31_t* pScratchOut, - uint32_t blockSize); - - -/** - * @brief Initialization function for the Q15 sparse FIR filter. - * @param[in,out] S points to an instance of the Q15 sparse FIR structure. - * @param[in] numTaps number of nonzero coefficients in the filter. - * @param[in] pCoeffs points to the array of filter coefficients. - * @param[in] pState points to the state buffer. - * @param[in] pTapDelay points to the array of offset times. - * @param[in] maxDelay maximum offset time supported. - * @param[in] blockSize number of samples that will be processed per block. - */ -void arm_fir_sparse_init_q15( - arm_fir_sparse_instance_q15* S, - uint16_t numTaps, - q15_t* pCoeffs, - q15_t* pState, - int32_t* pTapDelay, - uint16_t maxDelay, - uint32_t blockSize); - - -/** - * @brief Processing function for the Q7 sparse FIR filter. - * @param[in] S points to an instance of the Q7 sparse FIR structure. - * @param[in] pSrc points to the block of input data. - * @param[out] pDst points to the block of output data - * @param[in] pScratchIn points to a temporary buffer of size blockSize. - * @param[in] pScratchOut points to a temporary buffer of size blockSize. - * @param[in] blockSize number of input samples to process per call. - */ -void arm_fir_sparse_q7( - arm_fir_sparse_instance_q7* S, - q7_t* pSrc, - q7_t* pDst, - q7_t* pScratchIn, - q31_t* pScratchOut, - uint32_t blockSize); - - -/** - * @brief Initialization function for the Q7 sparse FIR filter. - * @param[in,out] S points to an instance of the Q7 sparse FIR structure. - * @param[in] numTaps number of nonzero coefficients in the filter. - * @param[in] pCoeffs points to the array of filter coefficients. - * @param[in] pState points to the state buffer. - * @param[in] pTapDelay points to the array of offset times. - * @param[in] maxDelay maximum offset time supported. - * @param[in] blockSize number of samples that will be processed per block. - */ -void arm_fir_sparse_init_q7( - arm_fir_sparse_instance_q7* S, - uint16_t numTaps, - q7_t* pCoeffs, - q7_t* pState, - int32_t* pTapDelay, - uint16_t maxDelay, - uint32_t blockSize); - - -/** - * @brief Floating-point sin_cos function. - * @param[in] theta input value in degrees - * @param[out] pSinVal points to the processed sine output. - * @param[out] pCosVal points to the processed cos output. - */ -void arm_sin_cos_f32( - float32_t theta, - float32_t* pSinVal, - float32_t* pCosVal); - - -/** - * @brief Q31 sin_cos function. - * @param[in] theta scaled input value in degrees - * @param[out] pSinVal points to the processed sine output. - * @param[out] pCosVal points to the processed cosine output. - */ -void arm_sin_cos_q31( - q31_t theta, - q31_t* pSinVal, - q31_t* pCosVal); - - -/** - * @brief Floating-point complex conjugate. - * @param[in] pSrc points to the input vector - * @param[out] pDst points to the output vector - * @param[in] numSamples number of complex samples in each vector - */ -void arm_cmplx_conj_f32( - float32_t* pSrc, - float32_t* pDst, - uint32_t numSamples); - -/** - * @brief Q31 complex conjugate. - * @param[in] pSrc points to the input vector - * @param[out] pDst points to the output vector - * @param[in] numSamples number of complex samples in each vector - */ -void arm_cmplx_conj_q31( - q31_t* pSrc, - q31_t* pDst, - uint32_t numSamples); - - -/** - * @brief Q15 complex conjugate. - * @param[in] pSrc points to the input vector - * @param[out] pDst points to the output vector - * @param[in] numSamples number of complex samples in each vector - */ -void arm_cmplx_conj_q15( - q15_t* pSrc, - q15_t* pDst, - uint32_t numSamples); - - -/** - * @brief Floating-point complex magnitude squared - * @param[in] pSrc points to the complex input vector - * @param[out] pDst points to the real output vector - * @param[in] numSamples number of complex samples in the input vector - */ -void arm_cmplx_mag_squared_f32( - float32_t* pSrc, - float32_t* pDst, - uint32_t numSamples); - - -/** - * @brief Q31 complex magnitude squared - * @param[in] pSrc points to the complex input vector - * @param[out] pDst points to the real output vector - * @param[in] numSamples number of complex samples in the input vector - */ -void arm_cmplx_mag_squared_q31( - q31_t* pSrc, - q31_t* pDst, - uint32_t numSamples); - - -/** - * @brief Q15 complex magnitude squared - * @param[in] pSrc points to the complex input vector - * @param[out] pDst points to the real output vector - * @param[in] numSamples number of complex samples in the input vector - */ -void arm_cmplx_mag_squared_q15( - q15_t* pSrc, - q15_t* pDst, - uint32_t numSamples); - - -/** - * @ingroup groupController - */ - -/** - * @defgroup PID PID Motor Control - * - * A Proportional Integral Derivative (PID) controller is a generic feedback control - * loop mechanism widely used in industrial control systems. - * A PID controller is the most commonly used type of feedback controller. - * - * This set of functions implements (PID) controllers - * for Q15, Q31, and floating-point data types. The functions operate on a single sample - * of data and each call to the function returns a single processed value. - * S points to an instance of the PID control data structure. in - * is the input sample value. The functions return the output value. - * - * \par Algorithm: - * 
- *    y[n] = y[n-1] + A0 * x[n] + A1 * x[n-1] + A2 * x[n-2]
- *    A0 = Kp + Ki + Kd
- *    A1 = (-Kp ) - (2 * Kd )
- *    A2 = Kd
- * - * \par - * where \c Kp is proportional constant, \c Ki is Integral constant and \c Kd is Derivative constant - * - * \par - * \image html PID.gif "Proportional Integral Derivative Controller" - * - * \par - * The PID controller calculates an "error" value as the difference between - * the measured output and the reference input. - * The controller attempts to minimize the error by adjusting the process control inputs. - * The proportional value determines the reaction to the current error, - * the integral value determines the reaction based on the sum of recent errors, - * and the derivative value determines the reaction based on the rate at which the error has been changing. - * - * \par Instance Structure - * The Gains A0, A1, A2 and state variables for a PID controller are stored together in an instance data structure. - * A separate instance structure must be defined for each PID Controller. - * There are separate instance structure declarations for each of the 3 supported data types. - * - * \par Reset Functions - * There is also an associated reset function for each data type which clears the state array. - * - * \par Initialization Functions - * There is also an associated initialization function for each data type. - * The initialization function performs the following operations: - * - Initializes the Gains A0, A1, A2 from Kp,Ki, Kd gains. - * - Zeros out the values in the state buffer. - * - * \par - * Instance structure cannot be placed into a const data section and it is recommended to use the initialization function. - * - * \par Fixed-Point Behavior - * Care must be taken when using the fixed-point versions of the PID Controller functions. - * In particular, the overflow and saturation behavior of the accumulator used in each function must be considered. - * Refer to the function specific documentation below for usage guidelines. - */ - -/** - * @addtogroup PID - * @{ - */ - -/** - * @brief Process function for the floating-point PID Control. - * @param[in,out] S is an instance of the floating-point PID Control structure - * @param[in] in input sample to process - * @return out processed output sample. - */ -static __INLINE float32_t arm_pid_f32( - arm_pid_instance_f32* S, - float32_t in) -{ - float32_t out; - /* y[n] = y[n-1] + A0 * x[n] + A1 * x[n-1] + A2 * x[n-2] */ - out = (S->A0 * in) + - (S->A1 * S->state[0]) + (S->A2 * S->state[1]) + (S->state[2]); - /* Update state */ - S->state[1] = S->state[0]; - S->state[0] = in; - S->state[2] = out; - /* return to application */ - return (out); -} - -/** - * @brief Process function for the Q31 PID Control. - * @param[in,out] S points to an instance of the Q31 PID Control structure - * @param[in] in input sample to process - * @return out processed output sample. - * - * Scaling and Overflow Behavior: - * \par - * The function is implemented using an internal 64-bit accumulator. - * The accumulator has a 2.62 format and maintains full precision of the intermediate multiplication results but provides only a single guard bit. - * Thus, if the accumulator result overflows it wraps around rather than clip. - * In order to avoid overflows completely the input signal must be scaled down by 2 bits as there are four additions. - * After all multiply-accumulates are performed, the 2.62 accumulator is truncated to 1.32 format and then saturated to 1.31 format. - */ -static __INLINE q31_t arm_pid_q31( - arm_pid_instance_q31* S, - q31_t in) -{ - q63_t acc; - q31_t out; - /* acc = A0 * x[n] */ - acc = (q63_t) S->A0 * in; - /* acc += A1 * x[n-1] */ - acc += (q63_t) S->A1 * S->state[0]; - /* acc += A2 * x[n-2] */ - acc += (q63_t) S->A2 * S->state[1]; - /* convert output to 1.31 format to add y[n-1] */ - out = (q31_t) (acc >> 31u); - /* out += y[n-1] */ - out += S->state[2]; - /* Update state */ - S->state[1] = S->state[0]; - S->state[0] = in; - S->state[2] = out; - /* return to application */ - return (out); -} - - -/** - * @brief Process function for the Q15 PID Control. - * @param[in,out] S points to an instance of the Q15 PID Control structure - * @param[in] in input sample to process - * @return out processed output sample. - * - * Scaling and Overflow Behavior: - * \par - * The function is implemented using a 64-bit internal accumulator. - * Both Gains and state variables are represented in 1.15 format and multiplications yield a 2.30 result. - * The 2.30 intermediate results are accumulated in a 64-bit accumulator in 34.30 format. - * There is no risk of internal overflow with this approach and the full precision of intermediate multiplications is preserved. - * After all additions have been performed, the accumulator is truncated to 34.15 format by discarding low 15 bits. - * Lastly, the accumulator is saturated to yield a result in 1.15 format. - */ -static __INLINE q15_t arm_pid_q15( - arm_pid_instance_q15* S, - q15_t in) -{ - q63_t acc; - q15_t out; -#ifndef ARM_MATH_CM0_FAMILY - __SIMD32_TYPE* vstate; - /* Implementation of PID controller */ - /* acc = A0 * x[n] */ - acc = (q31_t) __SMUAD((uint32_t)S->A0, (uint32_t)in); - /* acc += A1 * x[n-1] + A2 * x[n-2] */ - vstate = __SIMD32_CONST(S->state); - acc = (q63_t)__SMLALD((uint32_t)S->A1, (uint32_t) * vstate, (uint64_t)acc); -#else - /* acc = A0 * x[n] */ - acc = ((q31_t) S->A0) * in; - /* acc += A1 * x[n-1] + A2 * x[n-2] */ - acc += (q31_t) S->A1 * S->state[0]; - acc += (q31_t) S->A2 * S->state[1]; -#endif - /* acc += y[n-1] */ - acc += (q31_t) S->state[2] << 15; - /* saturate the output */ - out = (q15_t) (__SSAT((acc >> 15), 16)); - /* Update state */ - S->state[1] = S->state[0]; - S->state[0] = in; - S->state[2] = out; - /* return to application */ - return (out); -} - -/** - * @} end of PID group - */ - - -/** - * @brief Floating-point matrix inverse. - * @param[in] src points to the instance of the input floating-point matrix structure. - * @param[out] dst points to the instance of the output floating-point matrix structure. - * @return The function returns ARM_MATH_SIZE_MISMATCH, if the dimensions do not match. - * If the input matrix is singular (does not have an inverse), then the algorithm terminates and returns error status ARM_MATH_SINGULAR. - */ -arm_status arm_mat_inverse_f32( - const arm_matrix_instance_f32* src, - arm_matrix_instance_f32* dst); - - -/** - * @brief Floating-point matrix inverse. - * @param[in] src points to the instance of the input floating-point matrix structure. - * @param[out] dst points to the instance of the output floating-point matrix structure. - * @return The function returns ARM_MATH_SIZE_MISMATCH, if the dimensions do not match. - * If the input matrix is singular (does not have an inverse), then the algorithm terminates and returns error status ARM_MATH_SINGULAR. - */ -arm_status arm_mat_inverse_f64( - const arm_matrix_instance_f64* src, - arm_matrix_instance_f64* dst); - - - -/** - * @ingroup groupController - */ - -/** - * @defgroup clarke Vector Clarke Transform - * Forward Clarke transform converts the instantaneous stator phases into a two-coordinate time invariant vector. - * Generally the Clarke transform uses three-phase currents Ia, Ib and Ic to calculate currents - * in the two-phase orthogonal stator axis Ialpha and Ibeta. - * When Ialpha is superposed with Ia as shown in the figure below - * \image html clarke.gif Stator current space vector and its components in (a,b). - * and Ia + Ib + Ic = 0, in this condition Ialpha and Ibeta - * can be calculated using only Ia and Ib. - * - * The function operates on a single sample of data and each call to the function returns the processed output. - * The library provides separate functions for Q31 and floating-point data types. - * \par Algorithm - * \image html clarkeFormula.gif - * where Ia and Ib are the instantaneous stator phases and - * pIalpha and pIbeta are the two coordinates of time invariant vector. - * \par Fixed-Point Behavior - * Care must be taken when using the Q31 version of the Clarke transform. - * In particular, the overflow and saturation behavior of the accumulator used must be considered. - * Refer to the function specific documentation below for usage guidelines. - */ - -/** - * @addtogroup clarke - * @{ - */ - -/** - * - * @brief Floating-point Clarke transform - * @param[in] Ia input three-phase coordinate a - * @param[in] Ib input three-phase coordinate b - * @param[out] pIalpha points to output two-phase orthogonal vector axis alpha - * @param[out] pIbeta points to output two-phase orthogonal vector axis beta - */ -static __INLINE void arm_clarke_f32( - float32_t Ia, - float32_t Ib, - float32_t* pIalpha, - float32_t* pIbeta) -{ - /* Calculate pIalpha using the equation, pIalpha = Ia */ - *pIalpha = Ia; - /* Calculate pIbeta using the equation, pIbeta = (1/sqrt(3)) * Ia + (2/sqrt(3)) * Ib */ - *pIbeta = ((float32_t) 0.57735026919 * Ia + (float32_t) 1.15470053838 * Ib); -} - - -/** - * @brief Clarke transform for Q31 version - * @param[in] Ia input three-phase coordinate a - * @param[in] Ib input three-phase coordinate b - * @param[out] pIalpha points to output two-phase orthogonal vector axis alpha - * @param[out] pIbeta points to output two-phase orthogonal vector axis beta - * - * Scaling and Overflow Behavior: - * \par - * The function is implemented using an internal 32-bit accumulator. - * The accumulator maintains 1.31 format by truncating lower 31 bits of the intermediate multiplication in 2.62 format. - * There is saturation on the addition, hence there is no risk of overflow. - */ -static __INLINE void arm_clarke_q31( - q31_t Ia, - q31_t Ib, - q31_t* pIalpha, - q31_t* pIbeta) -{ - q31_t product1, product2; /* Temporary variables used to store intermediate results */ - /* Calculating pIalpha from Ia by equation pIalpha = Ia */ - *pIalpha = Ia; - /* Intermediate product is calculated by (1/(sqrt(3)) * Ia) */ - product1 = (q31_t) (((q63_t) Ia * 0x24F34E8B) >> 30); - /* Intermediate product is calculated by (2/sqrt(3) * Ib) */ - product2 = (q31_t) (((q63_t) Ib * 0x49E69D16) >> 30); - /* pIbeta is calculated by adding the intermediate products */ - *pIbeta = __QADD(product1, product2); -} - -/** - * @} end of clarke group - */ - -/** - * @brief Converts the elements of the Q7 vector to Q31 vector. - * @param[in] pSrc input pointer - * @param[out] pDst output pointer - * @param[in] blockSize number of samples to process - */ -void arm_q7_to_q31( - q7_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - - - -/** - * @ingroup groupController - */ - -/** - * @defgroup inv_clarke Vector Inverse Clarke Transform - * Inverse Clarke transform converts the two-coordinate time invariant vector into instantaneous stator phases. - * - * The function operates on a single sample of data and each call to the function returns the processed output. - * The library provides separate functions for Q31 and floating-point data types. - * \par Algorithm - * \image html clarkeInvFormula.gif - * where pIa and pIb are the instantaneous stator phases and - * Ialpha and Ibeta are the two coordinates of time invariant vector. - * \par Fixed-Point Behavior - * Care must be taken when using the Q31 version of the Clarke transform. - * In particular, the overflow and saturation behavior of the accumulator used must be considered. - * Refer to the function specific documentation below for usage guidelines. - */ - -/** - * @addtogroup inv_clarke - * @{ - */ - -/** -* @brief Floating-point Inverse Clarke transform -* @param[in] Ialpha input two-phase orthogonal vector axis alpha -* @param[in] Ibeta input two-phase orthogonal vector axis beta -* @param[out] pIa points to output three-phase coordinate a -* @param[out] pIb points to output three-phase coordinate b -*/ -static __INLINE void arm_inv_clarke_f32( - float32_t Ialpha, - float32_t Ibeta, - float32_t* pIa, - float32_t* pIb) -{ - /* Calculating pIa from Ialpha by equation pIa = Ialpha */ - *pIa = Ialpha; - /* Calculating pIb from Ialpha and Ibeta by equation pIb = -(1/2) * Ialpha + (sqrt(3)/2) * Ibeta */ - *pIb = -0.5f * Ialpha + 0.8660254039f * Ibeta; -} - - -/** - * @brief Inverse Clarke transform for Q31 version - * @param[in] Ialpha input two-phase orthogonal vector axis alpha - * @param[in] Ibeta input two-phase orthogonal vector axis beta - * @param[out] pIa points to output three-phase coordinate a - * @param[out] pIb points to output three-phase coordinate b - * - * Scaling and Overflow Behavior: - * \par - * The function is implemented using an internal 32-bit accumulator. - * The accumulator maintains 1.31 format by truncating lower 31 bits of the intermediate multiplication in 2.62 format. - * There is saturation on the subtraction, hence there is no risk of overflow. - */ -static __INLINE void arm_inv_clarke_q31( - q31_t Ialpha, - q31_t Ibeta, - q31_t* pIa, - q31_t* pIb) -{ - q31_t product1, product2; /* Temporary variables used to store intermediate results */ - /* Calculating pIa from Ialpha by equation pIa = Ialpha */ - *pIa = Ialpha; - /* Intermediate product is calculated by (1/(2*sqrt(3)) * Ia) */ - product1 = (q31_t) (((q63_t) (Ialpha) * (0x40000000)) >> 31); - /* Intermediate product is calculated by (1/sqrt(3) * pIb) */ - product2 = (q31_t) (((q63_t) (Ibeta) * (0x6ED9EBA1)) >> 31); - /* pIb is calculated by subtracting the products */ - *pIb = __QSUB(product2, product1); -} - -/** - * @} end of inv_clarke group - */ - -/** - * @brief Converts the elements of the Q7 vector to Q15 vector. - * @param[in] pSrc input pointer - * @param[out] pDst output pointer - * @param[in] blockSize number of samples to process - */ -void arm_q7_to_q15( - q7_t* pSrc, - q15_t* pDst, - uint32_t blockSize); - - - -/** - * @ingroup groupController - */ - -/** - * @defgroup park Vector Park Transform - * - * Forward Park transform converts the input two-coordinate vector to flux and torque components. - * The Park transform can be used to realize the transformation of the Ialpha and the Ibeta currents - * from the stationary to the moving reference frame and control the spatial relationship between - * the stator vector current and rotor flux vector. - * If we consider the d axis aligned with the rotor flux, the diagram below shows the - * current vector and the relationship from the two reference frames: - * \image html park.gif "Stator current space vector and its component in (a,b) and in the d,q rotating reference frame" - * - * The function operates on a single sample of data and each call to the function returns the processed output. - * The library provides separate functions for Q31 and floating-point data types. - * \par Algorithm - * \image html parkFormula.gif - * where Ialpha and Ibeta are the stator vector components, - * pId and pIq are rotor vector components and cosVal and sinVal are the - * cosine and sine values of theta (rotor flux position). - * \par Fixed-Point Behavior - * Care must be taken when using the Q31 version of the Park transform. - * In particular, the overflow and saturation behavior of the accumulator used must be considered. - * Refer to the function specific documentation below for usage guidelines. - */ - -/** - * @addtogroup park - * @{ - */ - -/** - * @brief Floating-point Park transform - * @param[in] Ialpha input two-phase vector coordinate alpha - * @param[in] Ibeta input two-phase vector coordinate beta - * @param[out] pId points to output rotor reference frame d - * @param[out] pIq points to output rotor reference frame q - * @param[in] sinVal sine value of rotation angle theta - * @param[in] cosVal cosine value of rotation angle theta - * - * The function implements the forward Park transform. - * - */ -static __INLINE void arm_park_f32( - float32_t Ialpha, - float32_t Ibeta, - float32_t* pId, - float32_t* pIq, - float32_t sinVal, - float32_t cosVal) -{ - /* Calculate pId using the equation, pId = Ialpha * cosVal + Ibeta * sinVal */ - *pId = Ialpha * cosVal + Ibeta * sinVal; - /* Calculate pIq using the equation, pIq = - Ialpha * sinVal + Ibeta * cosVal */ - *pIq = -Ialpha * sinVal + Ibeta * cosVal; -} - - -/** - * @brief Park transform for Q31 version - * @param[in] Ialpha input two-phase vector coordinate alpha - * @param[in] Ibeta input two-phase vector coordinate beta - * @param[out] pId points to output rotor reference frame d - * @param[out] pIq points to output rotor reference frame q - * @param[in] sinVal sine value of rotation angle theta - * @param[in] cosVal cosine value of rotation angle theta - * - * Scaling and Overflow Behavior: - * \par - * The function is implemented using an internal 32-bit accumulator. - * The accumulator maintains 1.31 format by truncating lower 31 bits of the intermediate multiplication in 2.62 format. - * There is saturation on the addition and subtraction, hence there is no risk of overflow. - */ -static __INLINE void arm_park_q31( - q31_t Ialpha, - q31_t Ibeta, - q31_t* pId, - q31_t* pIq, - q31_t sinVal, - q31_t cosVal) -{ - q31_t product1, product2; /* Temporary variables used to store intermediate results */ - q31_t product3, product4; /* Temporary variables used to store intermediate results */ - /* Intermediate product is calculated by (Ialpha * cosVal) */ - product1 = (q31_t) (((q63_t) (Ialpha) * (cosVal)) >> 31); - /* Intermediate product is calculated by (Ibeta * sinVal) */ - product2 = (q31_t) (((q63_t) (Ibeta) * (sinVal)) >> 31); - /* Intermediate product is calculated by (Ialpha * sinVal) */ - product3 = (q31_t) (((q63_t) (Ialpha) * (sinVal)) >> 31); - /* Intermediate product is calculated by (Ibeta * cosVal) */ - product4 = (q31_t) (((q63_t) (Ibeta) * (cosVal)) >> 31); - /* Calculate pId by adding the two intermediate products 1 and 2 */ - *pId = __QADD(product1, product2); - /* Calculate pIq by subtracting the two intermediate products 3 from 4 */ - *pIq = __QSUB(product4, product3); -} - -/** - * @} end of park group - */ - -/** - * @brief Converts the elements of the Q7 vector to floating-point vector. - * @param[in] pSrc is input pointer - * @param[out] pDst is output pointer - * @param[in] blockSize is the number of samples to process - */ -void arm_q7_to_float( - q7_t* pSrc, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @ingroup groupController - */ - -/** - * @defgroup inv_park Vector Inverse Park transform - * Inverse Park transform converts the input flux and torque components to two-coordinate vector. - * - * The function operates on a single sample of data and each call to the function returns the processed output. - * The library provides separate functions for Q31 and floating-point data types. - * \par Algorithm - * \image html parkInvFormula.gif - * where pIalpha and pIbeta are the stator vector components, - * Id and Iq are rotor vector components and cosVal and sinVal are the - * cosine and sine values of theta (rotor flux position). - * \par Fixed-Point Behavior - * Care must be taken when using the Q31 version of the Park transform. - * In particular, the overflow and saturation behavior of the accumulator used must be considered. - * Refer to the function specific documentation below for usage guidelines. - */ - -/** - * @addtogroup inv_park - * @{ - */ - -/** -* @brief Floating-point Inverse Park transform -* @param[in] Id input coordinate of rotor reference frame d -* @param[in] Iq input coordinate of rotor reference frame q -* @param[out] pIalpha points to output two-phase orthogonal vector axis alpha -* @param[out] pIbeta points to output two-phase orthogonal vector axis beta -* @param[in] sinVal sine value of rotation angle theta -* @param[in] cosVal cosine value of rotation angle theta -*/ -static __INLINE void arm_inv_park_f32( - float32_t Id, - float32_t Iq, - float32_t* pIalpha, - float32_t* pIbeta, - float32_t sinVal, - float32_t cosVal) -{ - /* Calculate pIalpha using the equation, pIalpha = Id * cosVal - Iq * sinVal */ - *pIalpha = Id * cosVal - Iq * sinVal; - /* Calculate pIbeta using the equation, pIbeta = Id * sinVal + Iq * cosVal */ - *pIbeta = Id * sinVal + Iq * cosVal; -} - - -/** - * @brief Inverse Park transform for Q31 version - * @param[in] Id input coordinate of rotor reference frame d - * @param[in] Iq input coordinate of rotor reference frame q - * @param[out] pIalpha points to output two-phase orthogonal vector axis alpha - * @param[out] pIbeta points to output two-phase orthogonal vector axis beta - * @param[in] sinVal sine value of rotation angle theta - * @param[in] cosVal cosine value of rotation angle theta - * - * Scaling and Overflow Behavior: - * \par - * The function is implemented using an internal 32-bit accumulator. - * The accumulator maintains 1.31 format by truncating lower 31 bits of the intermediate multiplication in 2.62 format. - * There is saturation on the addition, hence there is no risk of overflow. - */ -static __INLINE void arm_inv_park_q31( - q31_t Id, - q31_t Iq, - q31_t* pIalpha, - q31_t* pIbeta, - q31_t sinVal, - q31_t cosVal) -{ - q31_t product1, product2; /* Temporary variables used to store intermediate results */ - q31_t product3, product4; /* Temporary variables used to store intermediate results */ - /* Intermediate product is calculated by (Id * cosVal) */ - product1 = (q31_t) (((q63_t) (Id) * (cosVal)) >> 31); - /* Intermediate product is calculated by (Iq * sinVal) */ - product2 = (q31_t) (((q63_t) (Iq) * (sinVal)) >> 31); - /* Intermediate product is calculated by (Id * sinVal) */ - product3 = (q31_t) (((q63_t) (Id) * (sinVal)) >> 31); - /* Intermediate product is calculated by (Iq * cosVal) */ - product4 = (q31_t) (((q63_t) (Iq) * (cosVal)) >> 31); - /* Calculate pIalpha by using the two intermediate products 1 and 2 */ - *pIalpha = __QSUB(product1, product2); - /* Calculate pIbeta by using the two intermediate products 3 and 4 */ - *pIbeta = __QADD(product4, product3); -} - -/** - * @} end of Inverse park group - */ - - -/** - * @brief Converts the elements of the Q31 vector to floating-point vector. - * @param[in] pSrc is input pointer - * @param[out] pDst is output pointer - * @param[in] blockSize is the number of samples to process - */ -void arm_q31_to_float( - q31_t* pSrc, - float32_t* pDst, - uint32_t blockSize); - -/** - * @ingroup groupInterpolation - */ - -/** - * @defgroup LinearInterpolate Linear Interpolation - * - * Linear interpolation is a method of curve fitting using linear polynomials. - * Linear interpolation works by effectively drawing a straight line between two neighboring samples and returning the appropriate point along that line - * - * \par - * \image html LinearInterp.gif "Linear interpolation" - * - * \par - * A Linear Interpolate function calculates an output value(y), for the input(x) - * using linear interpolation of the input values x0, x1( nearest input values) and the output values y0 and y1(nearest output values) - * - * \par Algorithm: - * 
- *       y = y0 + (x - x0) * ((y1 - y0)/(x1-x0))
- *       where x0, x1 are nearest values of input x
- *             y0, y1 are nearest values to output y
- *
- * - * \par - * This set of functions implements Linear interpolation process - * for Q7, Q15, Q31, and floating-point data types. The functions operate on a single - * sample of data and each call to the function returns a single processed value. - * S points to an instance of the Linear Interpolate function data structure. - * x is the input sample value. The functions returns the output value. - * - * \par - * if x is outside of the table boundary, Linear interpolation returns first value of the table - * if x is below input range and returns last value of table if x is above range. - */ - -/** - * @addtogroup LinearInterpolate - * @{ - */ - -/** - * @brief Process function for the floating-point Linear Interpolation Function. - * @param[in,out] S is an instance of the floating-point Linear Interpolation structure - * @param[in] x input sample to process - * @return y processed output sample. - * - */ -static __INLINE float32_t arm_linear_interp_f32( - arm_linear_interp_instance_f32* S, - float32_t x) -{ - float32_t y; - float32_t x0, x1; /* Nearest input values */ - float32_t y0, y1; /* Nearest output values */ - float32_t xSpacing = S->xSpacing; /* spacing between input values */ - int32_t i; /* Index variable */ - float32_t* pYData = S->pYData; /* pointer to output table */ - /* Calculation of index */ - i = (int32_t) ((x - S->x1) / xSpacing); - - if (i < 0) - { - /* Iniatilize output for below specified range as least output value of table */ - y = pYData[0]; - } - else if ((uint32_t)i >= S->nValues) - { - /* Iniatilize output for above specified range as last output value of table */ - y = pYData[S->nValues - 1]; - } - else - { - /* Calculation of nearest input values */ - x0 = S->x1 + i * xSpacing; - x1 = S->x1 + (i + 1) * xSpacing; - /* Read of nearest output values */ - y0 = pYData[i]; - y1 = pYData[i + 1]; - /* Calculation of output */ - y = y0 + (x - x0) * ((y1 - y0) / (x1 - x0)); - } - - /* returns output value */ - return (y); -} - - -/** -* -* @brief Process function for the Q31 Linear Interpolation Function. -* @param[in] pYData pointer to Q31 Linear Interpolation table -* @param[in] x input sample to process -* @param[in] nValues number of table values -* @return y processed output sample. -* -* \par -* Input sample x is in 12.20 format which contains 12 bits for table index and 20 bits for fractional part. -* This function can support maximum of table size 2^12. -* -*/ -static __INLINE q31_t arm_linear_interp_q31( - q31_t* pYData, - q31_t x, - uint32_t nValues) -{ - q31_t y; /* output */ - q31_t y0, y1; /* Nearest output values */ - q31_t fract; /* fractional part */ - int32_t index; /* Index to read nearest output values */ - /* Input is in 12.20 format */ - /* 12 bits for the table index */ - /* Index value calculation */ - index = ((x & (q31_t)0xFFF00000) >> 20); - - if (index >= (int32_t)(nValues - 1)) - { - return (pYData[nValues - 1]); - } - else if (index < 0) - { - return (pYData[0]); - } - else - { - /* 20 bits for the fractional part */ - /* shift left by 11 to keep fract in 1.31 format */ - fract = (x & 0x000FFFFF) << 11; - /* Read two nearest output values from the index in 1.31(q31) format */ - y0 = pYData[index]; - y1 = pYData[index + 1]; - /* Calculation of y0 * (1-fract) and y is in 2.30 format */ - y = ((q31_t) ((q63_t) y0 * (0x7FFFFFFF - fract) >> 32)); - /* Calculation of y0 * (1-fract) + y1 *fract and y is in 2.30 format */ - y += ((q31_t) (((q63_t) y1 * fract) >> 32)); - /* Convert y to 1.31 format */ - return (y << 1u); - } -} - - -/** - * - * @brief Process function for the Q15 Linear Interpolation Function. - * @param[in] pYData pointer to Q15 Linear Interpolation table - * @param[in] x input sample to process - * @param[in] nValues number of table values - * @return y processed output sample. - * - * \par - * Input sample x is in 12.20 format which contains 12 bits for table index and 20 bits for fractional part. - * This function can support maximum of table size 2^12. - * - */ -static __INLINE q15_t arm_linear_interp_q15( - q15_t* pYData, - q31_t x, - uint32_t nValues) -{ - q63_t y; /* output */ - q15_t y0, y1; /* Nearest output values */ - q31_t fract; /* fractional part */ - int32_t index; /* Index to read nearest output values */ - /* Input is in 12.20 format */ - /* 12 bits for the table index */ - /* Index value calculation */ - index = ((x & (int32_t)0xFFF00000) >> 20); - - if (index >= (int32_t)(nValues - 1)) - { - return (pYData[nValues - 1]); - } - else if (index < 0) - { - return (pYData[0]); - } - else - { - /* 20 bits for the fractional part */ - /* fract is in 12.20 format */ - fract = (x & 0x000FFFFF); - /* Read two nearest output values from the index */ - y0 = pYData[index]; - y1 = pYData[index + 1]; - /* Calculation of y0 * (1-fract) and y is in 13.35 format */ - y = ((q63_t) y0 * (0xFFFFF - fract)); - /* Calculation of (y0 * (1-fract) + y1 * fract) and y is in 13.35 format */ - y += ((q63_t) y1 * (fract)); - /* convert y to 1.15 format */ - return (q15_t) (y >> 20); - } -} - - -/** - * - * @brief Process function for the Q7 Linear Interpolation Function. - * @param[in] pYData pointer to Q7 Linear Interpolation table - * @param[in] x input sample to process - * @param[in] nValues number of table values - * @return y processed output sample. - * - * \par - * Input sample x is in 12.20 format which contains 12 bits for table index and 20 bits for fractional part. - * This function can support maximum of table size 2^12. - */ -static __INLINE q7_t arm_linear_interp_q7( - q7_t* pYData, - q31_t x, - uint32_t nValues) -{ - q31_t y; /* output */ - q7_t y0, y1; /* Nearest output values */ - q31_t fract; /* fractional part */ - uint32_t index; /* Index to read nearest output values */ - - /* Input is in 12.20 format */ - /* 12 bits for the table index */ - /* Index value calculation */ - if (x < 0) - { - return (pYData[0]); - } - - index = (x >> 20) & 0xfff; - - if (index >= (nValues - 1)) - { - return (pYData[nValues - 1]); - } - else - { - /* 20 bits for the fractional part */ - /* fract is in 12.20 format */ - fract = (x & 0x000FFFFF); - /* Read two nearest output values from the index and are in 1.7(q7) format */ - y0 = pYData[index]; - y1 = pYData[index + 1]; - /* Calculation of y0 * (1-fract ) and y is in 13.27(q27) format */ - y = ((y0 * (0xFFFFF - fract))); - /* Calculation of y1 * fract + y0 * (1-fract) and y is in 13.27(q27) format */ - y += (y1 * fract); - /* convert y to 1.7(q7) format */ - return (q7_t) (y >> 20); - } -} - -/** - * @} end of LinearInterpolate group - */ - -/** - * @brief Fast approximation to the trigonometric sine function for floating-point data. - * @param[in] x input value in radians. - * @return sin(x). - */ -float32_t arm_sin_f32( - float32_t x); - - -/** - * @brief Fast approximation to the trigonometric sine function for Q31 data. - * @param[in] x Scaled input value in radians. - * @return sin(x). - */ -q31_t arm_sin_q31( - q31_t x); - - -/** - * @brief Fast approximation to the trigonometric sine function for Q15 data. - * @param[in] x Scaled input value in radians. - * @return sin(x). - */ -q15_t arm_sin_q15( - q15_t x); - - -/** - * @brief Fast approximation to the trigonometric cosine function for floating-point data. - * @param[in] x input value in radians. - * @return cos(x). - */ -float32_t arm_cos_f32( - float32_t x); - - -/** - * @brief Fast approximation to the trigonometric cosine function for Q31 data. - * @param[in] x Scaled input value in radians. - * @return cos(x). - */ -q31_t arm_cos_q31( - q31_t x); - - -/** - * @brief Fast approximation to the trigonometric cosine function for Q15 data. - * @param[in] x Scaled input value in radians. - * @return cos(x). - */ -q15_t arm_cos_q15( - q15_t x); - - -/** - * @ingroup groupFastMath - */ - - -/** - * @defgroup SQRT Square Root - * - * Computes the square root of a number. - * There are separate functions for Q15, Q31, and floating-point data types. - * The square root function is computed using the Newton-Raphson algorithm. - * This is an iterative algorithm of the form: - * 
- *      x1 = x0 - f(x0)/f'(x0)
- *
- * where x1 is the current estimate, - * x0 is the previous estimate, and - * f'(x0) is the derivative of f() evaluated at x0. - * For the square root function, the algorithm reduces to: - * 
- *     x0 = in/2                         [initial guess]
- *     x1 = 1/2 * ( x0 + in / x0)        [each iteration]
- *
- */ - - -/** - * @addtogroup SQRT - * @{ - */ - -/** - * @brief Floating-point square root function. - * @param[in] in input value. - * @param[out] pOut square root of input value. - * @return The function returns ARM_MATH_SUCCESS if input value is positive value or ARM_MATH_ARGUMENT_ERROR if - * in is negative value and returns zero output for negative values. - */ -static __INLINE arm_status arm_sqrt_f32( - float32_t in, - float32_t* pOut) -{ - if (in >= 0.0f) - { -#if (__FPU_USED == 1) && defined ( __CC_ARM ) - *pOut = __sqrtf(in); -#elif (__FPU_USED == 1) && (defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)) - *pOut = __builtin_sqrtf(in); -#elif (__FPU_USED == 1) && defined(__GNUC__) - *pOut = __builtin_sqrtf(in); -#elif (__FPU_USED == 1) && defined ( __ICCARM__ ) && (__VER__ >= 6040000) - __ASM("VSQRT.F32 %0,%1" : "=t"(*pOut) : "t"(in)); -#else - *pOut = sqrtf(in); -#endif - return (ARM_MATH_SUCCESS); - } - else - { - *pOut = 0.0f; - return (ARM_MATH_ARGUMENT_ERROR); - } -} - - -/** - * @brief Q31 square root function. - * @param[in] in input value. The range of the input value is [0 +1) or 0x00000000 to 0x7FFFFFFF. - * @param[out] pOut square root of input value. - * @return The function returns ARM_MATH_SUCCESS if input value is positive value or ARM_MATH_ARGUMENT_ERROR if - * in is negative value and returns zero output for negative values. - */ -arm_status arm_sqrt_q31( - q31_t in, - q31_t* pOut); - - -/** - * @brief Q15 square root function. - * @param[in] in input value. The range of the input value is [0 +1) or 0x0000 to 0x7FFF. - * @param[out] pOut square root of input value. - * @return The function returns ARM_MATH_SUCCESS if input value is positive value or ARM_MATH_ARGUMENT_ERROR if - * in is negative value and returns zero output for negative values. - */ -arm_status arm_sqrt_q15( - q15_t in, - q15_t* pOut); - -/** - * @} end of SQRT group - */ - - -/** - * @brief floating-point Circular write function. - */ -static __INLINE void arm_circularWrite_f32( - int32_t* circBuffer, - int32_t L, - uint16_t* writeOffset, - int32_t bufferInc, - const int32_t* src, - int32_t srcInc, - uint32_t blockSize) -{ - uint32_t i = 0u; - int32_t wOffset; - /* Copy the value of Index pointer that points - * to the current location where the input samples to be copied */ - wOffset = *writeOffset; - /* Loop over the blockSize */ - i = blockSize; - - while (i > 0u) - { - /* copy the input sample to the circular buffer */ - circBuffer[wOffset] = *src; - /* Update the input pointer */ - src += srcInc; - /* Circularly update wOffset. Watch out for positive and negative value */ - wOffset += bufferInc; - - if (wOffset >= L) - { - wOffset -= L; - } - - /* Decrement the loop counter */ - i--; - } - - /* Update the index pointer */ - *writeOffset = (uint16_t)wOffset; -} - - - -/** - * @brief floating-point Circular Read function. - */ -static __INLINE void arm_circularRead_f32( - int32_t* circBuffer, - int32_t L, - int32_t* readOffset, - int32_t bufferInc, - int32_t* dst, - int32_t* dst_base, - int32_t dst_length, - int32_t dstInc, - uint32_t blockSize) -{ - uint32_t i = 0u; - int32_t rOffset, dst_end; - /* Copy the value of Index pointer that points - * to the current location from where the input samples to be read */ - rOffset = *readOffset; - dst_end = (int32_t) (dst_base + dst_length); - /* Loop over the blockSize */ - i = blockSize; - - while (i > 0u) - { - /* copy the sample from the circular buffer to the destination buffer */ - *dst = circBuffer[rOffset]; - /* Update the input pointer */ - dst += dstInc; - - if (dst == (int32_t*) dst_end) - { - dst = dst_base; - } - - /* Circularly update rOffset. Watch out for positive and negative value */ - rOffset += bufferInc; - - if (rOffset >= L) - { - rOffset -= L; - } - - /* Decrement the loop counter */ - i--; - } - - /* Update the index pointer */ - *readOffset = rOffset; -} - - -/** - * @brief Q15 Circular write function. - */ -static __INLINE void arm_circularWrite_q15( - q15_t* circBuffer, - int32_t L, - uint16_t* writeOffset, - int32_t bufferInc, - const q15_t* src, - int32_t srcInc, - uint32_t blockSize) -{ - uint32_t i = 0u; - int32_t wOffset; - /* Copy the value of Index pointer that points - * to the current location where the input samples to be copied */ - wOffset = *writeOffset; - /* Loop over the blockSize */ - i = blockSize; - - while (i > 0u) - { - /* copy the input sample to the circular buffer */ - circBuffer[wOffset] = *src; - /* Update the input pointer */ - src += srcInc; - /* Circularly update wOffset. Watch out for positive and negative value */ - wOffset += bufferInc; - - if (wOffset >= L) - { - wOffset -= L; - } - - /* Decrement the loop counter */ - i--; - } - - /* Update the index pointer */ - *writeOffset = (uint16_t)wOffset; -} - - -/** - * @brief Q15 Circular Read function. - */ -static __INLINE void arm_circularRead_q15( - q15_t* circBuffer, - int32_t L, - int32_t* readOffset, - int32_t bufferInc, - q15_t* dst, - q15_t* dst_base, - int32_t dst_length, - int32_t dstInc, - uint32_t blockSize) -{ - uint32_t i = 0; - int32_t rOffset, dst_end; - /* Copy the value of Index pointer that points - * to the current location from where the input samples to be read */ - rOffset = *readOffset; - dst_end = (int32_t) (dst_base + dst_length); - /* Loop over the blockSize */ - i = blockSize; - - while (i > 0u) - { - /* copy the sample from the circular buffer to the destination buffer */ - *dst = circBuffer[rOffset]; - /* Update the input pointer */ - dst += dstInc; - - if (dst == (q15_t*) dst_end) - { - dst = dst_base; - } - - /* Circularly update wOffset. Watch out for positive and negative value */ - rOffset += bufferInc; - - if (rOffset >= L) - { - rOffset -= L; - } - - /* Decrement the loop counter */ - i--; - } - - /* Update the index pointer */ - *readOffset = rOffset; -} - - -/** - * @brief Q7 Circular write function. - */ -static __INLINE void arm_circularWrite_q7( - q7_t* circBuffer, - int32_t L, - uint16_t* writeOffset, - int32_t bufferInc, - const q7_t* src, - int32_t srcInc, - uint32_t blockSize) -{ - uint32_t i = 0u; - int32_t wOffset; - /* Copy the value of Index pointer that points - * to the current location where the input samples to be copied */ - wOffset = *writeOffset; - /* Loop over the blockSize */ - i = blockSize; - - while (i > 0u) - { - /* copy the input sample to the circular buffer */ - circBuffer[wOffset] = *src; - /* Update the input pointer */ - src += srcInc; - /* Circularly update wOffset. Watch out for positive and negative value */ - wOffset += bufferInc; - - if (wOffset >= L) - { - wOffset -= L; - } - - /* Decrement the loop counter */ - i--; - } - - /* Update the index pointer */ - *writeOffset = (uint16_t)wOffset; -} - - -/** - * @brief Q7 Circular Read function. - */ -static __INLINE void arm_circularRead_q7( - q7_t* circBuffer, - int32_t L, - int32_t* readOffset, - int32_t bufferInc, - q7_t* dst, - q7_t* dst_base, - int32_t dst_length, - int32_t dstInc, - uint32_t blockSize) -{ - uint32_t i = 0; - int32_t rOffset, dst_end; - /* Copy the value of Index pointer that points - * to the current location from where the input samples to be read */ - rOffset = *readOffset; - dst_end = (int32_t) (dst_base + dst_length); - /* Loop over the blockSize */ - i = blockSize; - - while (i > 0u) - { - /* copy the sample from the circular buffer to the destination buffer */ - *dst = circBuffer[rOffset]; - /* Update the input pointer */ - dst += dstInc; - - if (dst == (q7_t*) dst_end) - { - dst = dst_base; - } - - /* Circularly update rOffset. Watch out for positive and negative value */ - rOffset += bufferInc; - - if (rOffset >= L) - { - rOffset -= L; - } - - /* Decrement the loop counter */ - i--; - } - - /* Update the index pointer */ - *readOffset = rOffset; -} - - -/** - * @brief Sum of the squares of the elements of a Q31 vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_power_q31( - q31_t* pSrc, - uint32_t blockSize, - q63_t* pResult); - - -/** - * @brief Sum of the squares of the elements of a floating-point vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_power_f32( - float32_t* pSrc, - uint32_t blockSize, - float32_t* pResult); - - -/** - * @brief Sum of the squares of the elements of a Q15 vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_power_q15( - q15_t* pSrc, - uint32_t blockSize, - q63_t* pResult); - - -/** - * @brief Sum of the squares of the elements of a Q7 vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_power_q7( - q7_t* pSrc, - uint32_t blockSize, - q31_t* pResult); - - -/** - * @brief Mean value of a Q7 vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_mean_q7( - q7_t* pSrc, - uint32_t blockSize, - q7_t* pResult); - - -/** - * @brief Mean value of a Q15 vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_mean_q15( - q15_t* pSrc, - uint32_t blockSize, - q15_t* pResult); - - -/** - * @brief Mean value of a Q31 vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_mean_q31( - q31_t* pSrc, - uint32_t blockSize, - q31_t* pResult); - - -/** - * @brief Mean value of a floating-point vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_mean_f32( - float32_t* pSrc, - uint32_t blockSize, - float32_t* pResult); - - -/** - * @brief Variance of the elements of a floating-point vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_var_f32( - float32_t* pSrc, - uint32_t blockSize, - float32_t* pResult); - - -/** - * @brief Variance of the elements of a Q31 vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_var_q31( - q31_t* pSrc, - uint32_t blockSize, - q31_t* pResult); - - -/** - * @brief Variance of the elements of a Q15 vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_var_q15( - q15_t* pSrc, - uint32_t blockSize, - q15_t* pResult); - - -/** - * @brief Root Mean Square of the elements of a floating-point vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_rms_f32( - float32_t* pSrc, - uint32_t blockSize, - float32_t* pResult); - - -/** - * @brief Root Mean Square of the elements of a Q31 vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_rms_q31( - q31_t* pSrc, - uint32_t blockSize, - q31_t* pResult); - - -/** - * @brief Root Mean Square of the elements of a Q15 vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_rms_q15( - q15_t* pSrc, - uint32_t blockSize, - q15_t* pResult); - - -/** - * @brief Standard deviation of the elements of a floating-point vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_std_f32( - float32_t* pSrc, - uint32_t blockSize, - float32_t* pResult); - - -/** - * @brief Standard deviation of the elements of a Q31 vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_std_q31( - q31_t* pSrc, - uint32_t blockSize, - q31_t* pResult); - - -/** - * @brief Standard deviation of the elements of a Q15 vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output value. - */ -void arm_std_q15( - q15_t* pSrc, - uint32_t blockSize, - q15_t* pResult); - - -/** - * @brief Floating-point complex magnitude - * @param[in] pSrc points to the complex input vector - * @param[out] pDst points to the real output vector - * @param[in] numSamples number of complex samples in the input vector - */ -void arm_cmplx_mag_f32( - float32_t* pSrc, - float32_t* pDst, - uint32_t numSamples); - - -/** - * @brief Q31 complex magnitude - * @param[in] pSrc points to the complex input vector - * @param[out] pDst points to the real output vector - * @param[in] numSamples number of complex samples in the input vector - */ -void arm_cmplx_mag_q31( - q31_t* pSrc, - q31_t* pDst, - uint32_t numSamples); - - -/** - * @brief Q15 complex magnitude - * @param[in] pSrc points to the complex input vector - * @param[out] pDst points to the real output vector - * @param[in] numSamples number of complex samples in the input vector - */ -void arm_cmplx_mag_q15( - q15_t* pSrc, - q15_t* pDst, - uint32_t numSamples); - - -/** - * @brief Q15 complex dot product - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[in] numSamples number of complex samples in each vector - * @param[out] realResult real part of the result returned here - * @param[out] imagResult imaginary part of the result returned here - */ -void arm_cmplx_dot_prod_q15( - q15_t* pSrcA, - q15_t* pSrcB, - uint32_t numSamples, - q31_t* realResult, - q31_t* imagResult); - - -/** - * @brief Q31 complex dot product - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[in] numSamples number of complex samples in each vector - * @param[out] realResult real part of the result returned here - * @param[out] imagResult imaginary part of the result returned here - */ -void arm_cmplx_dot_prod_q31( - q31_t* pSrcA, - q31_t* pSrcB, - uint32_t numSamples, - q63_t* realResult, - q63_t* imagResult); - - -/** - * @brief Floating-point complex dot product - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[in] numSamples number of complex samples in each vector - * @param[out] realResult real part of the result returned here - * @param[out] imagResult imaginary part of the result returned here - */ -void arm_cmplx_dot_prod_f32( - float32_t* pSrcA, - float32_t* pSrcB, - uint32_t numSamples, - float32_t* realResult, - float32_t* imagResult); - - -/** - * @brief Q15 complex-by-real multiplication - * @param[in] pSrcCmplx points to the complex input vector - * @param[in] pSrcReal points to the real input vector - * @param[out] pCmplxDst points to the complex output vector - * @param[in] numSamples number of samples in each vector - */ -void arm_cmplx_mult_real_q15( - q15_t* pSrcCmplx, - q15_t* pSrcReal, - q15_t* pCmplxDst, - uint32_t numSamples); - - -/** - * @brief Q31 complex-by-real multiplication - * @param[in] pSrcCmplx points to the complex input vector - * @param[in] pSrcReal points to the real input vector - * @param[out] pCmplxDst points to the complex output vector - * @param[in] numSamples number of samples in each vector - */ -void arm_cmplx_mult_real_q31( - q31_t* pSrcCmplx, - q31_t* pSrcReal, - q31_t* pCmplxDst, - uint32_t numSamples); - - -/** - * @brief Floating-point complex-by-real multiplication - * @param[in] pSrcCmplx points to the complex input vector - * @param[in] pSrcReal points to the real input vector - * @param[out] pCmplxDst points to the complex output vector - * @param[in] numSamples number of samples in each vector - */ -void arm_cmplx_mult_real_f32( - float32_t* pSrcCmplx, - float32_t* pSrcReal, - float32_t* pCmplxDst, - uint32_t numSamples); - - -/** - * @brief Minimum value of a Q7 vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] result is output pointer - * @param[in] index is the array index of the minimum value in the input buffer. - */ -void arm_min_q7( - q7_t* pSrc, - uint32_t blockSize, - q7_t* result, - uint32_t* index); - - -/** - * @brief Minimum value of a Q15 vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output pointer - * @param[in] pIndex is the array index of the minimum value in the input buffer. - */ -void arm_min_q15( - q15_t* pSrc, - uint32_t blockSize, - q15_t* pResult, - uint32_t* pIndex); - - -/** - * @brief Minimum value of a Q31 vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output pointer - * @param[out] pIndex is the array index of the minimum value in the input buffer. - */ -void arm_min_q31( - q31_t* pSrc, - uint32_t blockSize, - q31_t* pResult, - uint32_t* pIndex); - - -/** - * @brief Minimum value of a floating-point vector. - * @param[in] pSrc is input pointer - * @param[in] blockSize is the number of samples to process - * @param[out] pResult is output pointer - * @param[out] pIndex is the array index of the minimum value in the input buffer. - */ -void arm_min_f32( - float32_t* pSrc, - uint32_t blockSize, - float32_t* pResult, - uint32_t* pIndex); - - -/** - * @brief Maximum value of a Q7 vector. - * @param[in] pSrc points to the input buffer - * @param[in] blockSize length of the input vector - * @param[out] pResult maximum value returned here - * @param[out] pIndex index of maximum value returned here - */ -void arm_max_q7( - q7_t* pSrc, - uint32_t blockSize, - q7_t* pResult, - uint32_t* pIndex); - - -/** - * @brief Maximum value of a Q15 vector. - * @param[in] pSrc points to the input buffer - * @param[in] blockSize length of the input vector - * @param[out] pResult maximum value returned here - * @param[out] pIndex index of maximum value returned here - */ -void arm_max_q15( - q15_t* pSrc, - uint32_t blockSize, - q15_t* pResult, - uint32_t* pIndex); - - -/** - * @brief Maximum value of a Q31 vector. - * @param[in] pSrc points to the input buffer - * @param[in] blockSize length of the input vector - * @param[out] pResult maximum value returned here - * @param[out] pIndex index of maximum value returned here - */ -void arm_max_q31( - q31_t* pSrc, - uint32_t blockSize, - q31_t* pResult, - uint32_t* pIndex); - - -/** - * @brief Maximum value of a floating-point vector. - * @param[in] pSrc points to the input buffer - * @param[in] blockSize length of the input vector - * @param[out] pResult maximum value returned here - * @param[out] pIndex index of maximum value returned here - */ -void arm_max_f32( - float32_t* pSrc, - uint32_t blockSize, - float32_t* pResult, - uint32_t* pIndex); - - -/** - * @brief Q15 complex-by-complex multiplication - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[out] pDst points to the output vector - * @param[in] numSamples number of complex samples in each vector - */ -void arm_cmplx_mult_cmplx_q15( - q15_t* pSrcA, - q15_t* pSrcB, - q15_t* pDst, - uint32_t numSamples); - - -/** - * @brief Q31 complex-by-complex multiplication - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[out] pDst points to the output vector - * @param[in] numSamples number of complex samples in each vector - */ -void arm_cmplx_mult_cmplx_q31( - q31_t* pSrcA, - q31_t* pSrcB, - q31_t* pDst, - uint32_t numSamples); - - -/** - * @brief Floating-point complex-by-complex multiplication - * @param[in] pSrcA points to the first input vector - * @param[in] pSrcB points to the second input vector - * @param[out] pDst points to the output vector - * @param[in] numSamples number of complex samples in each vector - */ -void arm_cmplx_mult_cmplx_f32( - float32_t* pSrcA, - float32_t* pSrcB, - float32_t* pDst, - uint32_t numSamples); - - -/** - * @brief Converts the elements of the floating-point vector to Q31 vector. - * @param[in] pSrc points to the floating-point input vector - * @param[out] pDst points to the Q31 output vector - * @param[in] blockSize length of the input vector - */ -void arm_float_to_q31( - float32_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Converts the elements of the floating-point vector to Q15 vector. - * @param[in] pSrc points to the floating-point input vector - * @param[out] pDst points to the Q15 output vector - * @param[in] blockSize length of the input vector - */ -void arm_float_to_q15( - float32_t* pSrc, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Converts the elements of the floating-point vector to Q7 vector. - * @param[in] pSrc points to the floating-point input vector - * @param[out] pDst points to the Q7 output vector - * @param[in] blockSize length of the input vector - */ -void arm_float_to_q7( - float32_t* pSrc, - q7_t* pDst, - uint32_t blockSize); - - -/** - * @brief Converts the elements of the Q31 vector to Q15 vector. - * @param[in] pSrc is input pointer - * @param[out] pDst is output pointer - * @param[in] blockSize is the number of samples to process - */ -void arm_q31_to_q15( - q31_t* pSrc, - q15_t* pDst, - uint32_t blockSize); - - -/** - * @brief Converts the elements of the Q31 vector to Q7 vector. - * @param[in] pSrc is input pointer - * @param[out] pDst is output pointer - * @param[in] blockSize is the number of samples to process - */ -void arm_q31_to_q7( - q31_t* pSrc, - q7_t* pDst, - uint32_t blockSize); - - -/** - * @brief Converts the elements of the Q15 vector to floating-point vector. - * @param[in] pSrc is input pointer - * @param[out] pDst is output pointer - * @param[in] blockSize is the number of samples to process - */ -void arm_q15_to_float( - q15_t* pSrc, - float32_t* pDst, - uint32_t blockSize); - - -/** - * @brief Converts the elements of the Q15 vector to Q31 vector. - * @param[in] pSrc is input pointer - * @param[out] pDst is output pointer - * @param[in] blockSize is the number of samples to process - */ -void arm_q15_to_q31( - q15_t* pSrc, - q31_t* pDst, - uint32_t blockSize); - - -/** - * @brief Converts the elements of the Q15 vector to Q7 vector. - * @param[in] pSrc is input pointer - * @param[out] pDst is output pointer - * @param[in] blockSize is the number of samples to process - */ -void arm_q15_to_q7( - q15_t* pSrc, - q7_t* pDst, - uint32_t blockSize); - - -/** - * @ingroup groupInterpolation - */ - -/** - * @defgroup BilinearInterpolate Bilinear Interpolation - * - * Bilinear interpolation is an extension of linear interpolation applied to a two dimensional grid. - * The underlying function f(x, y) is sampled on a regular grid and the interpolation process - * determines values between the grid points. - * Bilinear interpolation is equivalent to two step linear interpolation, first in the x-dimension and then in the y-dimension. - * Bilinear interpolation is often used in image processing to rescale images. - * The CMSIS DSP library provides bilinear interpolation functions for Q7, Q15, Q31, and floating-point data types. - * - * Algorithm - * \par - * The instance structure used by the bilinear interpolation functions describes a two dimensional data table. - * For floating-point, the instance structure is defined as: - * 
- *   typedef struct
- *   {
- *     uint16_t numRows;
- *     uint16_t numCols;
- *     float32_t *pData;
- * } arm_bilinear_interp_instance_f32;
- *
- * - * \par - * where numRows specifies the number of rows in the table; - * numCols specifies the number of columns in the table; - * and pData points to an array of size numRows*numCols values. - * The data table pTable is organized in row order and the supplied data values fall on integer indexes. - * That is, table element (x,y) is located at pTable[x + y*numCols] where x and y are integers. - * - * \par - * Let (x, y) specify the desired interpolation point. Then define: - * 
- *     XF = floor(x)
- *     YF = floor(y)
- *
- * \par - * The interpolated output point is computed as: - * 
- *  f(x, y) = f(XF, YF) * (1-(x-XF)) * (1-(y-YF))
- *           + f(XF+1, YF) * (x-XF)*(1-(y-YF))
- *           + f(XF, YF+1) * (1-(x-XF))*(y-YF)
- *           + f(XF+1, YF+1) * (x-XF)*(y-YF)
- *
- * Note that the coordinates (x, y) contain integer and fractional components. - * The integer components specify which portion of the table to use while the - * fractional components control the interpolation processor. - * - * \par - * if (x,y) are outside of the table boundary, Bilinear interpolation returns zero output. - */ - -/** - * @addtogroup BilinearInterpolate - * @{ - */ - - -/** -* -* @brief Floating-point bilinear interpolation. -* @param[in,out] S points to an instance of the interpolation structure. -* @param[in] X interpolation coordinate. -* @param[in] Y interpolation coordinate. -* @return out interpolated value. -*/ -static __INLINE float32_t arm_bilinear_interp_f32( - const arm_bilinear_interp_instance_f32* S, - float32_t X, - float32_t Y) -{ - float32_t out; - float32_t f00, f01, f10, f11; - float32_t* pData = S->pData; - int32_t xIndex, yIndex, index; - float32_t xdiff, ydiff; - float32_t b1, b2, b3, b4; - xIndex = (int32_t) X; - yIndex = (int32_t) Y; - - /* Care taken for table outside boundary */ - /* Returns zero output when values are outside table boundary */ - if (xIndex < 0 || xIndex > (S->numRows - 1) || yIndex < 0 || yIndex > (S->numCols - 1)) - { - return (0); - } - - /* Calculation of index for two nearest points in X-direction */ - index = (xIndex - 1) + (yIndex - 1) * S->numCols; - /* Read two nearest points in X-direction */ - f00 = pData[index]; - f01 = pData[index + 1]; - /* Calculation of index for two nearest points in Y-direction */ - index = (xIndex - 1) + (yIndex) * S->numCols; - /* Read two nearest points in Y-direction */ - f10 = pData[index]; - f11 = pData[index + 1]; - /* Calculation of intermediate values */ - b1 = f00; - b2 = f01 - f00; - b3 = f10 - f00; - b4 = f00 - f01 - f10 + f11; - /* Calculation of fractional part in X */ - xdiff = X - xIndex; - /* Calculation of fractional part in Y */ - ydiff = Y - yIndex; - /* Calculation of bi-linear interpolated output */ - out = b1 + b2 * xdiff + b3 * ydiff + b4 * xdiff * ydiff; - /* return to application */ - return (out); -} - - -/** -* -* @brief Q31 bilinear interpolation. -* @param[in,out] S points to an instance of the interpolation structure. -* @param[in] X interpolation coordinate in 12.20 format. -* @param[in] Y interpolation coordinate in 12.20 format. -* @return out interpolated value. -*/ -static __INLINE q31_t arm_bilinear_interp_q31( - arm_bilinear_interp_instance_q31* S, - q31_t X, - q31_t Y) -{ - q31_t out; /* Temporary output */ - q31_t acc = 0; /* output */ - q31_t xfract, yfract; /* X, Y fractional parts */ - q31_t x1, x2, y1, y2; /* Nearest output values */ - int32_t rI, cI; /* Row and column indices */ - q31_t* pYData = S->pData; /* pointer to output table values */ - uint32_t nCols = S->numCols; /* num of rows */ - /* Input is in 12.20 format */ - /* 12 bits for the table index */ - /* Index value calculation */ - rI = ((X & (q31_t)0xFFF00000) >> 20); - /* Input is in 12.20 format */ - /* 12 bits for the table index */ - /* Index value calculation */ - cI = ((Y & (q31_t)0xFFF00000) >> 20); - - /* Care taken for table outside boundary */ - /* Returns zero output when values are outside table boundary */ - if (rI < 0 || rI > (S->numRows - 1) || cI < 0 || cI > (S->numCols - 1)) - { - return (0); - } - - /* 20 bits for the fractional part */ - /* shift left xfract by 11 to keep 1.31 format */ - xfract = (X & 0x000FFFFF) << 11u; - /* Read two nearest output values from the index */ - x1 = pYData[(rI) + (int32_t)nCols * (cI) ]; - x2 = pYData[(rI) + (int32_t)nCols * (cI) + 1]; - /* 20 bits for the fractional part */ - /* shift left yfract by 11 to keep 1.31 format */ - yfract = (Y & 0x000FFFFF) << 11u; - /* Read two nearest output values from the index */ - y1 = pYData[(rI) + (int32_t)nCols * (cI + 1) ]; - y2 = pYData[(rI) + (int32_t)nCols * (cI + 1) + 1]; - /* Calculation of x1 * (1-xfract ) * (1-yfract) and acc is in 3.29(q29) format */ - out = ((q31_t) (((q63_t) x1 * (0x7FFFFFFF - xfract)) >> 32)); - acc = ((q31_t) (((q63_t) out * (0x7FFFFFFF - yfract)) >> 32)); - /* x2 * (xfract) * (1-yfract) in 3.29(q29) and adding to acc */ - out = ((q31_t) ((q63_t) x2 * (0x7FFFFFFF - yfract) >> 32)); - acc += ((q31_t) ((q63_t) out * (xfract) >> 32)); - /* y1 * (1 - xfract) * (yfract) in 3.29(q29) and adding to acc */ - out = ((q31_t) ((q63_t) y1 * (0x7FFFFFFF - xfract) >> 32)); - acc += ((q31_t) ((q63_t) out * (yfract) >> 32)); - /* y2 * (xfract) * (yfract) in 3.29(q29) and adding to acc */ - out = ((q31_t) ((q63_t) y2 * (xfract) >> 32)); - acc += ((q31_t) ((q63_t) out * (yfract) >> 32)); - /* Convert acc to 1.31(q31) format */ - return ((q31_t)(acc << 2)); -} - - -/** -* @brief Q15 bilinear interpolation. -* @param[in,out] S points to an instance of the interpolation structure. -* @param[in] X interpolation coordinate in 12.20 format. -* @param[in] Y interpolation coordinate in 12.20 format. -* @return out interpolated value. -*/ -static __INLINE q15_t arm_bilinear_interp_q15( - arm_bilinear_interp_instance_q15* S, - q31_t X, - q31_t Y) -{ - q63_t acc = 0; /* output */ - q31_t out; /* Temporary output */ - q15_t x1, x2, y1, y2; /* Nearest output values */ - q31_t xfract, yfract; /* X, Y fractional parts */ - int32_t rI, cI; /* Row and column indices */ - q15_t* pYData = S->pData; /* pointer to output table values */ - uint32_t nCols = S->numCols; /* num of rows */ - /* Input is in 12.20 format */ - /* 12 bits for the table index */ - /* Index value calculation */ - rI = ((X & (q31_t)0xFFF00000) >> 20); - /* Input is in 12.20 format */ - /* 12 bits for the table index */ - /* Index value calculation */ - cI = ((Y & (q31_t)0xFFF00000) >> 20); - - /* Care taken for table outside boundary */ - /* Returns zero output when values are outside table boundary */ - if (rI < 0 || rI > (S->numRows - 1) || cI < 0 || cI > (S->numCols - 1)) - { - return (0); - } - - /* 20 bits for the fractional part */ - /* xfract should be in 12.20 format */ - xfract = (X & 0x000FFFFF); - /* Read two nearest output values from the index */ - x1 = pYData[((uint32_t)rI) + nCols * ((uint32_t)cI) ]; - x2 = pYData[((uint32_t)rI) + nCols * ((uint32_t)cI) + 1]; - /* 20 bits for the fractional part */ - /* yfract should be in 12.20 format */ - yfract = (Y & 0x000FFFFF); - /* Read two nearest output values from the index */ - y1 = pYData[((uint32_t)rI) + nCols * ((uint32_t)cI + 1) ]; - y2 = pYData[((uint32_t)rI) + nCols * ((uint32_t)cI + 1) + 1]; - /* Calculation of x1 * (1-xfract ) * (1-yfract) and acc is in 13.51 format */ - /* x1 is in 1.15(q15), xfract in 12.20 format and out is in 13.35 format */ - /* convert 13.35 to 13.31 by right shifting and out is in 1.31 */ - out = (q31_t) (((q63_t) x1 * (0xFFFFF - xfract)) >> 4u); - acc = ((q63_t) out * (0xFFFFF - yfract)); - /* x2 * (xfract) * (1-yfract) in 1.51 and adding to acc */ - out = (q31_t) (((q63_t) x2 * (0xFFFFF - yfract)) >> 4u); - acc += ((q63_t) out * (xfract)); - /* y1 * (1 - xfract) * (yfract) in 1.51 and adding to acc */ - out = (q31_t) (((q63_t) y1 * (0xFFFFF - xfract)) >> 4u); - acc += ((q63_t) out * (yfract)); - /* y2 * (xfract) * (yfract) in 1.51 and adding to acc */ - out = (q31_t) (((q63_t) y2 * (xfract)) >> 4u); - acc += ((q63_t) out * (yfract)); - /* acc is in 13.51 format and down shift acc by 36 times */ - /* Convert out to 1.15 format */ - return ((q15_t)(acc >> 36)); -} - - -/** -* @brief Q7 bilinear interpolation. -* @param[in,out] S points to an instance of the interpolation structure. -* @param[in] X interpolation coordinate in 12.20 format. -* @param[in] Y interpolation coordinate in 12.20 format. -* @return out interpolated value. -*/ -static __INLINE q7_t arm_bilinear_interp_q7( - arm_bilinear_interp_instance_q7* S, - q31_t X, - q31_t Y) -{ - q63_t acc = 0; /* output */ - q31_t out; /* Temporary output */ - q31_t xfract, yfract; /* X, Y fractional parts */ - q7_t x1, x2, y1, y2; /* Nearest output values */ - int32_t rI, cI; /* Row and column indices */ - q7_t* pYData = S->pData; /* pointer to output table values */ - uint32_t nCols = S->numCols; /* num of rows */ - /* Input is in 12.20 format */ - /* 12 bits for the table index */ - /* Index value calculation */ - rI = ((X & (q31_t)0xFFF00000) >> 20); - /* Input is in 12.20 format */ - /* 12 bits for the table index */ - /* Index value calculation */ - cI = ((Y & (q31_t)0xFFF00000) >> 20); - - /* Care taken for table outside boundary */ - /* Returns zero output when values are outside table boundary */ - if (rI < 0 || rI > (S->numRows - 1) || cI < 0 || cI > (S->numCols - 1)) - { - return (0); - } - - /* 20 bits for the fractional part */ - /* xfract should be in 12.20 format */ - xfract = (X & (q31_t)0x000FFFFF); - /* Read two nearest output values from the index */ - x1 = pYData[((uint32_t)rI) + nCols * ((uint32_t)cI) ]; - x2 = pYData[((uint32_t)rI) + nCols * ((uint32_t)cI) + 1]; - /* 20 bits for the fractional part */ - /* yfract should be in 12.20 format */ - yfract = (Y & (q31_t)0x000FFFFF); - /* Read two nearest output values from the index */ - y1 = pYData[((uint32_t)rI) + nCols * ((uint32_t)cI + 1) ]; - y2 = pYData[((uint32_t)rI) + nCols * ((uint32_t)cI + 1) + 1]; - /* Calculation of x1 * (1-xfract ) * (1-yfract) and acc is in 16.47 format */ - out = ((x1 * (0xFFFFF - xfract))); - acc = (((q63_t) out * (0xFFFFF - yfract))); - /* x2 * (xfract) * (1-yfract) in 2.22 and adding to acc */ - out = ((x2 * (0xFFFFF - yfract))); - acc += (((q63_t) out * (xfract))); - /* y1 * (1 - xfract) * (yfract) in 2.22 and adding to acc */ - out = ((y1 * (0xFFFFF - xfract))); - acc += (((q63_t) out * (yfract))); - /* y2 * (xfract) * (yfract) in 2.22 and adding to acc */ - out = ((y2 * (yfract))); - acc += (((q63_t) out * (xfract))); - /* acc in 16.47 format and down shift by 40 to convert to 1.7 format */ - return ((q7_t)(acc >> 40)); -} - -/** - * @} end of BilinearInterpolate group - */ - - -/* SMMLAR */ -#define multAcc_32x32_keep32_R(a, x, y) \ - a = (q31_t) (((((q63_t) a) << 32) + ((q63_t) x * y) + 0x80000000LL ) >> 32) - -/* SMMLSR */ -#define multSub_32x32_keep32_R(a, x, y) \ - a = (q31_t) (((((q63_t) a) << 32) - ((q63_t) x * y) + 0x80000000LL ) >> 32) - -/* SMMULR */ -#define mult_32x32_keep32_R(a, x, y) \ - a = (q31_t) (((q63_t) x * y + 0x80000000LL ) >> 32) - -/* SMMLA */ -#define multAcc_32x32_keep32(a, x, y) \ - a += (q31_t) (((q63_t) x * y) >> 32) - -/* SMMLS */ -#define multSub_32x32_keep32(a, x, y) \ - a -= (q31_t) (((q63_t) x * y) >> 32) - -/* SMMUL */ -#define mult_32x32_keep32(a, x, y) \ - a = (q31_t) (((q63_t) x * y ) >> 32) - - -#if defined ( __CC_ARM ) -/* Enter low optimization region - place directly above function definition */ -#if defined( ARM_MATH_CM4 ) || defined( ARM_MATH_CM7) -#define LOW_OPTIMIZATION_ENTER \ - _Pragma ("push") \ - _Pragma ("O1") -#else -#define LOW_OPTIMIZATION_ENTER -#endif - -/* Exit low optimization region - place directly after end of function definition */ -#if defined( ARM_MATH_CM4 ) || defined( ARM_MATH_CM7) -#define LOW_OPTIMIZATION_EXIT \ - _Pragma ("pop") -#else -#define LOW_OPTIMIZATION_EXIT -#endif - -/* Enter low optimization region - place directly above function definition */ -#define IAR_ONLY_LOW_OPTIMIZATION_ENTER - -/* Exit low optimization region - place directly after end of function definition */ -#define IAR_ONLY_LOW_OPTIMIZATION_EXIT - -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) -#define LOW_OPTIMIZATION_ENTER -#define LOW_OPTIMIZATION_EXIT -#define IAR_ONLY_LOW_OPTIMIZATION_ENTER -#define IAR_ONLY_LOW_OPTIMIZATION_EXIT - -#elif defined(__GNUC__) -#define LOW_OPTIMIZATION_ENTER __attribute__(( optimize("-O1") )) -#define LOW_OPTIMIZATION_EXIT -#define IAR_ONLY_LOW_OPTIMIZATION_ENTER -#define IAR_ONLY_LOW_OPTIMIZATION_EXIT - -#elif defined(__ICCARM__) -/* Enter low optimization region - place directly above function definition */ -#if defined( ARM_MATH_CM4 ) || defined( ARM_MATH_CM7) -#define LOW_OPTIMIZATION_ENTER \ - _Pragma ("optimize=low") -#else -#define LOW_OPTIMIZATION_ENTER -#endif - -/* Exit low optimization region - place directly after end of function definition */ -#define LOW_OPTIMIZATION_EXIT - -/* Enter low optimization region - place directly above function definition */ -#if defined( ARM_MATH_CM4 ) || defined( ARM_MATH_CM7) -#define IAR_ONLY_LOW_OPTIMIZATION_ENTER \ - _Pragma ("optimize=low") -#else -#define IAR_ONLY_LOW_OPTIMIZATION_ENTER -#endif - -/* Exit low optimization region - place directly after end of function definition */ -#define IAR_ONLY_LOW_OPTIMIZATION_EXIT - -#elif defined(__CSMC__) -#define LOW_OPTIMIZATION_ENTER -#define LOW_OPTIMIZATION_EXIT -#define IAR_ONLY_LOW_OPTIMIZATION_ENTER -#define IAR_ONLY_LOW_OPTIMIZATION_EXIT - -#elif defined(__TASKING__) -#define LOW_OPTIMIZATION_ENTER -#define LOW_OPTIMIZATION_EXIT -#define IAR_ONLY_LOW_OPTIMIZATION_ENTER -#define IAR_ONLY_LOW_OPTIMIZATION_EXIT - -#endif - - -#ifdef __cplusplus -} -#endif - - -#if defined ( __GNUC__ ) -#pragma GCC diagnostic pop -#endif - -#endif /* _ARM_MATH_H */ - -/** - * - * End of file. - */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/cmsis_armcc.h b/EpsilonLights/Drivers/CMSIS/Include/cmsis_armcc.h index 29199714..a21a8b16 100644 --- a/EpsilonLights/Drivers/CMSIS/Include/cmsis_armcc.h +++ b/EpsilonLights/Drivers/CMSIS/Include/cmsis_armcc.h @@ -1,43 +1,104 @@ /**************************************************************************//** * @file cmsis_armcc.h - * @brief CMSIS Cortex-M Core Function/Instruction Header File - * @version V4.30 - * @date 20. October 2015 + * @brief CMSIS compiler ARMCC (Arm Compiler 5) header file + * @version V5.0.4 + * @date 10. January 2018 ******************************************************************************/ -/* Copyright (c) 2009 - 2015 ARM LIMITED - - All rights reserved. - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - - Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - - Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - Neither the name of ARM nor the names of its contributors may be used - to endorse or promote products derived from this software without - specific prior written permission. - * - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE - LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR - CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF - SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS - INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN - CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) - ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE - POSSIBILITY OF SUCH DAMAGE. - ---------------------------------------------------------------------------*/ - +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ #ifndef __CMSIS_ARMCC_H #define __CMSIS_ARMCC_H #if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 400677) -#error "Please use ARM Compiler Toolchain V4.0.677 or later!" +#error "Please use Arm Compiler Toolchain V4.0.677 or later!" +#endif + +/* CMSIS compiler control architecture macros */ +#if ((defined (__TARGET_ARCH_6_M ) && (__TARGET_ARCH_6_M == 1)) || \ + (defined (__TARGET_ARCH_6S_M ) && (__TARGET_ARCH_6S_M == 1)) ) +#define __ARM_ARCH_6M__ 1 +#endif + +#if (defined (__TARGET_ARCH_7_M ) && (__TARGET_ARCH_7_M == 1)) +#define __ARM_ARCH_7M__ 1 +#endif + +#if (defined (__TARGET_ARCH_7E_M) && (__TARGET_ARCH_7E_M == 1)) +#define __ARM_ARCH_7EM__ 1 +#endif + +/* __ARM_ARCH_8M_BASE__ not applicable */ +/* __ARM_ARCH_8M_MAIN__ not applicable */ + + +/* CMSIS compiler specific defines */ +#ifndef __ASM +#define __ASM __asm +#endif +#ifndef __INLINE +#define __INLINE __inline +#endif +#ifndef __STATIC_INLINE +#define __STATIC_INLINE static __inline +#endif +#ifndef __STATIC_FORCEINLINE +#define __STATIC_FORCEINLINE static __forceinline +#endif +#ifndef __NO_RETURN +#define __NO_RETURN __declspec(noreturn) +#endif +#ifndef __USED +#define __USED __attribute__((used)) +#endif +#ifndef __WEAK +#define __WEAK __attribute__((weak)) +#endif +#ifndef __PACKED +#define __PACKED __attribute__((packed)) +#endif +#ifndef __PACKED_STRUCT +#define __PACKED_STRUCT __packed struct +#endif +#ifndef __PACKED_UNION +#define __PACKED_UNION __packed union +#endif +#ifndef __UNALIGNED_UINT32 /* deprecated */ +#define __UNALIGNED_UINT32(x) (*((__packed uint32_t *)(x))) +#endif +#ifndef __UNALIGNED_UINT16_WRITE +#define __UNALIGNED_UINT16_WRITE(addr, val) ((*((__packed uint16_t *)(addr))) = (val)) +#endif +#ifndef __UNALIGNED_UINT16_READ +#define __UNALIGNED_UINT16_READ(addr) (*((const __packed uint16_t *)(addr))) +#endif +#ifndef __UNALIGNED_UINT32_WRITE +#define __UNALIGNED_UINT32_WRITE(addr, val) ((*((__packed uint32_t *)(addr))) = (val)) +#endif +#ifndef __UNALIGNED_UINT32_READ +#define __UNALIGNED_UINT32_READ(addr) (*((const __packed uint32_t *)(addr))) +#endif +#ifndef __ALIGNED +#define __ALIGNED(x) __attribute__((aligned(x))) +#endif +#ifndef __RESTRICT +#define __RESTRICT __restrict #endif /* ########################### Core Function Access ########################### */ @@ -46,7 +107,19 @@ @{ */ +/** + \brief Enable IRQ Interrupts + \details Enables IRQ interrupts by clearing the I-bit in the CPSR. + Can only be executed in Privileged modes. + */ /* intrinsic void __enable_irq(); */ + + +/** + \brief Disable IRQ Interrupts + \details Disables IRQ interrupts by setting the I-bit in the CPSR. + Can only be executed in Privileged modes. + */ /* intrinsic void __disable_irq(); */ /** @@ -181,7 +254,8 @@ __STATIC_INLINE void __set_PRIMASK(uint32_t priMask) } -#if (__CORTEX_M >= 0x03U) || (__CORTEX_SC >= 300U) +#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1)) ) /** \brief Enable FIQ @@ -256,14 +330,13 @@ __STATIC_INLINE uint32_t __get_FAULTMASK(void) __STATIC_INLINE void __set_FAULTMASK(uint32_t faultMask) { register uint32_t __regFaultMask __ASM("faultmask"); - __regFaultMask = (faultMask & (uint32_t)1); + __regFaultMask = (faultMask & (uint32_t)1U); } -#endif /* (__CORTEX_M >= 0x03U) || (__CORTEX_SC >= 300U) */ +#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1)) ) */ -#if (__CORTEX_M == 0x04U) || (__CORTEX_M == 0x07U) - /** \brief Get FPSCR \details Returns the current value of the Floating Point Status/Control register. @@ -271,7 +344,8 @@ __STATIC_INLINE void __set_FAULTMASK(uint32_t faultMask) */ __STATIC_INLINE uint32_t __get_FPSCR(void) { -#if (__FPU_PRESENT == 1U) && (__FPU_USED == 1U) +#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \ + (defined (__FPU_USED ) && (__FPU_USED == 1U)) ) register uint32_t __regfpscr __ASM("fpscr"); return (__regfpscr); #else @@ -287,15 +361,15 @@ __STATIC_INLINE uint32_t __get_FPSCR(void) */ __STATIC_INLINE void __set_FPSCR(uint32_t fpscr) { -#if (__FPU_PRESENT == 1U) && (__FPU_USED == 1U) +#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \ + (defined (__FPU_USED ) && (__FPU_USED == 1U)) ) register uint32_t __regfpscr __ASM("fpscr"); __regfpscr = (fpscr); +#else + (void)fpscr; #endif } -#endif /* (__CORTEX_M == 0x04U) || (__CORTEX_M == 0x07U) */ - - /*@} end of CMSIS_Core_RegAccFunctions */ @@ -369,9 +443,10 @@ __STATIC_INLINE void __set_FPSCR(uint32_t fpscr) __schedule_barrier();\ } while (0U) + /** \brief Reverse byte order (32 bit) - \details Reverses the byte order in integer value. + \details Reverses the byte order in unsigned integer value. For example, 0x12345678 becomes 0x78563412. \param [in] value Value to reverse \return Reversed value */ @@ -380,7 +455,7 @@ __STATIC_INLINE void __set_FPSCR(uint32_t fpscr) /** \brief Reverse byte order (16 bit) - \details Reverses the byte order in two unsigned short values. + \details Reverses the byte order within each halfword of a word. For example, 0x12345678 becomes 0x34127856. \param [in] value Value to reverse \return Reversed value */ @@ -392,14 +467,15 @@ __attribute__((section(".rev16_text"))) __STATIC_INLINE __ASM uint32_t __REV16(u } #endif + /** - \brief Reverse byte order in signed short value - \details Reverses the byte order in a signed short value with sign extension to integer. + \brief Reverse byte order (16 bit) + \details Reverses the byte order in a 16-bit value and returns the signed 16-bit result. For example, 0x0080 becomes 0x8000. \param [in] value Value to reverse \return Reversed value */ #ifndef __NO_EMBEDDED_ASM -__attribute__((section(".revsh_text"))) __STATIC_INLINE __ASM int32_t __REVSH(int32_t value) +__attribute__((section(".revsh_text"))) __STATIC_INLINE __ASM int16_t __REVSH(int16_t value) { revsh r0, r0 bx lr @@ -410,8 +486,8 @@ __attribute__((section(".revsh_text"))) __STATIC_INLINE __ASM int32_t __REVSH(in /** \brief Rotate Right in unsigned value (32 bit) \details Rotate Right (immediate) provides the value of the contents of a register rotated by a variable number of bits. - \param [in] value Value to rotate - \param [in] value Number of Bits to rotate + \param [in] op1 Value to rotate + \param [in] op2 Number of Bits to rotate \return Rotated value */ #define __ROR __ror @@ -433,16 +509,18 @@ __attribute__((section(".revsh_text"))) __STATIC_INLINE __ASM int32_t __REVSH(in \param [in] value Value to reverse \return Reversed value */ -#if (__CORTEX_M >= 0x03U) || (__CORTEX_SC >= 300U) +#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1)) ) #define __RBIT __rbit #else __attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value) { uint32_t result; - int32_t s = 4 /*sizeof(v)*/ * 8 - 1; /* extra shift needed at end */ + uint32_t s = (4U /*sizeof(v)*/ * 8U) - 1U; /* extra shift needed at end */ + result = value; /* r will be reversed bits of v; first get LSB of v */ - for (value >>= 1U; value; value >>= 1U) + for (value >>= 1U; value != 0U; value >>= 1U) { result <<= 1U; result |= value & 1U; @@ -450,7 +528,7 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value) } result <<= s; /* shift when v's highest bits are zero */ - return (result); + return result; } #endif @@ -464,7 +542,8 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value) #define __CLZ __clz -#if (__CORTEX_M >= 0x03U) || (__CORTEX_SC >= 300U) +#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1)) ) /** \brief LDR Exclusive (8 bit) @@ -646,7 +725,64 @@ __attribute__((section(".rrx_text"))) __STATIC_INLINE __ASM uint32_t __RRX(uint3 */ #define __STRT(value, ptr) __strt(value, ptr) -#endif /* (__CORTEX_M >= 0x03U) || (__CORTEX_SC >= 300U) */ +#else /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1)) ) */ + +/** + \brief Signed Saturate + \details Saturates a signed value. + \param [in] value Value to be saturated + \param [in] sat Bit position to saturate to (1..32) + \return Saturated value + */ +__attribute__((always_inline)) __STATIC_INLINE int32_t __SSAT(int32_t val, uint32_t sat) +{ + if ((sat >= 1U) && (sat <= 32U)) + { + const int32_t max = (int32_t)((1U << (sat - 1U)) - 1U); + const int32_t min = -1 - max ; + + if (val > max) + { + return max; + } + else if (val < min) + { + return min; + } + } + + return val; +} + +/** + \brief Unsigned Saturate + \details Saturates an unsigned value. + \param [in] value Value to be saturated + \param [in] sat Bit position to saturate to (0..31) + \return Saturated value + */ +__attribute__((always_inline)) __STATIC_INLINE uint32_t __USAT(int32_t val, uint32_t sat) +{ + if (sat <= 31U) + { + const uint32_t max = ((1U << sat) - 1U); + + if (val > (int32_t)max) + { + return max; + } + else if (val < 0) + { + return 0U; + } + } + + return (uint32_t)val; +} + +#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1)) ) */ /*@}*/ /* end of group CMSIS_Core_InstructionInterface */ @@ -657,7 +793,7 @@ __attribute__((section(".rrx_text"))) __STATIC_INLINE __ASM uint32_t __RRX(uint3 @{ */ -#if (__CORTEX_M >= 0x04U) /* only for Cortex-M4 and above */ +#if ((defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1)) ) #define __SADD8 __sadd8 #define __QADD8 __qadd8 @@ -728,7 +864,7 @@ __attribute__((section(".rrx_text"))) __STATIC_INLINE __ASM uint32_t __RRX(uint3 #define __SMMLA(ARG1,ARG2,ARG3) ( (int32_t)((((int64_t)(ARG1) * (ARG2)) + \ ((int64_t)(ARG3) << 32U) ) >> 32U)) -#endif /* (__CORTEX_M >= 0x04) */ +#endif /* ((defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1)) ) */ /*@} end of group CMSIS_SIMD_intrinsics */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/cmsis_armcc_V6.h b/EpsilonLights/Drivers/CMSIS/Include/cmsis_armclang.h similarity index 60% rename from EpsilonLights/Drivers/CMSIS/Include/cmsis_armcc_V6.h rename to EpsilonLights/Drivers/CMSIS/Include/cmsis_armclang.h index 549eef81..0d7eefd3 100644 --- a/EpsilonLights/Drivers/CMSIS/Include/cmsis_armcc_V6.h +++ b/EpsilonLights/Drivers/CMSIS/Include/cmsis_armclang.h @@ -1,39 +1,118 @@ /**************************************************************************//** - * @file cmsis_armcc_V6.h - * @brief CMSIS Cortex-M Core Function/Instruction Header File - * @version V4.30 - * @date 20. October 2015 + * @file cmsis_armclang.h + * @brief CMSIS compiler armclang (Arm Compiler 6) header file + * @version V5.0.4 + * @date 10. January 2018 ******************************************************************************/ -/* Copyright (c) 2009 - 2015 ARM LIMITED - - All rights reserved. - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - - Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - - Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - Neither the name of ARM nor the names of its contributors may be used - to endorse or promote products derived from this software without - specific prior written permission. - * - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE - LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR - CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF - SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS - INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN - CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) - ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE - POSSIBILITY OF SUCH DAMAGE. - ---------------------------------------------------------------------------*/ - - -#ifndef __CMSIS_ARMCC_V6_H -#define __CMSIS_ARMCC_V6_H +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ + +/*lint -esym(9058, IRQn)*/ /* disable MISRA 2012 Rule 2.4 for IRQn */ + +#ifndef __CMSIS_ARMCLANG_H +#define __CMSIS_ARMCLANG_H + +#pragma clang system_header /* treat file as system include file */ + +#ifndef __ARM_COMPAT_H +#include /* Compatibility header for Arm Compiler 5 intrinsics */ +#endif + +/* CMSIS compiler specific defines */ +#ifndef __ASM +#define __ASM __asm +#endif +#ifndef __INLINE +#define __INLINE __inline +#endif +#ifndef __STATIC_INLINE +#define __STATIC_INLINE static __inline +#endif +#ifndef __STATIC_FORCEINLINE +#define __STATIC_FORCEINLINE __attribute__((always_inline)) static __inline +#endif +#ifndef __NO_RETURN +#define __NO_RETURN __attribute__((__noreturn__)) +#endif +#ifndef __USED +#define __USED __attribute__((used)) +#endif +#ifndef __WEAK +#define __WEAK __attribute__((weak)) +#endif +#ifndef __PACKED +#define __PACKED __attribute__((packed, aligned(1))) +#endif +#ifndef __PACKED_STRUCT +#define __PACKED_STRUCT struct __attribute__((packed, aligned(1))) +#endif +#ifndef __PACKED_UNION +#define __PACKED_UNION union __attribute__((packed, aligned(1))) +#endif +#ifndef __UNALIGNED_UINT32 /* deprecated */ +#pragma clang diagnostic push +#pragma clang diagnostic ignored "-Wpacked" +/*lint -esym(9058, T_UINT32)*/ /* disable MISRA 2012 Rule 2.4 for T_UINT32 */ +struct __attribute__((packed)) T_UINT32 +{ + uint32_t v; +}; +#pragma clang diagnostic pop +#define __UNALIGNED_UINT32(x) (((struct T_UINT32 *)(x))->v) +#endif +#ifndef __UNALIGNED_UINT16_WRITE +#pragma clang diagnostic push +#pragma clang diagnostic ignored "-Wpacked" +/*lint -esym(9058, T_UINT16_WRITE)*/ /* disable MISRA 2012 Rule 2.4 for T_UINT16_WRITE */ +__PACKED_STRUCT T_UINT16_WRITE { uint16_t v; }; +#pragma clang diagnostic pop +#define __UNALIGNED_UINT16_WRITE(addr, val) (void)((((struct T_UINT16_WRITE *)(void *)(addr))->v) = (val)) +#endif +#ifndef __UNALIGNED_UINT16_READ +#pragma clang diagnostic push +#pragma clang diagnostic ignored "-Wpacked" +/*lint -esym(9058, T_UINT16_READ)*/ /* disable MISRA 2012 Rule 2.4 for T_UINT16_READ */ +__PACKED_STRUCT T_UINT16_READ { uint16_t v; }; +#pragma clang diagnostic pop +#define __UNALIGNED_UINT16_READ(addr) (((const struct T_UINT16_READ *)(const void *)(addr))->v) +#endif +#ifndef __UNALIGNED_UINT32_WRITE +#pragma clang diagnostic push +#pragma clang diagnostic ignored "-Wpacked" +/*lint -esym(9058, T_UINT32_WRITE)*/ /* disable MISRA 2012 Rule 2.4 for T_UINT32_WRITE */ +__PACKED_STRUCT T_UINT32_WRITE { uint32_t v; }; +#pragma clang diagnostic pop +#define __UNALIGNED_UINT32_WRITE(addr, val) (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val)) +#endif +#ifndef __UNALIGNED_UINT32_READ +#pragma clang diagnostic push +#pragma clang diagnostic ignored "-Wpacked" +/*lint -esym(9058, T_UINT32_READ)*/ /* disable MISRA 2012 Rule 2.4 for T_UINT32_READ */ +__PACKED_STRUCT T_UINT32_READ { uint32_t v; }; +#pragma clang diagnostic pop +#define __UNALIGNED_UINT32_READ(addr) (((const struct T_UINT32_READ *)(const void *)(addr))->v) +#endif +#ifndef __ALIGNED +#define __ALIGNED(x) __attribute__((aligned(x))) +#endif +#ifndef __RESTRICT +#define __RESTRICT __restrict +#endif /* ########################### Core Function Access ########################### */ @@ -47,10 +126,7 @@ \details Enables IRQ interrupts by clearing the I-bit in the CPSR. Can only be executed in Privileged modes. */ -__attribute__((always_inline)) __STATIC_INLINE void __enable_irq(void) -{ - __ASM volatile ("cpsie i" : : : "memory"); -} +/* intrinsic void __enable_irq(); see arm_compat.h */ /** @@ -58,10 +134,7 @@ __attribute__((always_inline)) __STATIC_INLINE void __enable_irq(void) \details Disables IRQ interrupts by setting the I-bit in the CPSR. Can only be executed in Privileged modes. */ -__attribute__((always_inline)) __STATIC_INLINE void __disable_irq(void) -{ - __ASM volatile ("cpsid i" : : : "memory"); -} +/* intrinsic void __disable_irq(); see arm_compat.h */ /** @@ -69,23 +142,25 @@ __attribute__((always_inline)) __STATIC_INLINE void __disable_irq(void) \details Returns the content of the Control Register. \return Control Register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __get_CONTROL(void) +__STATIC_FORCEINLINE uint32_t __get_CONTROL(void) { uint32_t result; + __ASM volatile ("MRS %0, control" : "=r" (result) ); return (result); } -#if (__ARM_FEATURE_CMSE == 3U) +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) /** \brief Get Control Register (non-secure) \details Returns the content of the non-secure Control Register when in secure mode. \return non-secure Control Register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_CONTROL_NS(void) +__STATIC_FORCEINLINE uint32_t __TZ_get_CONTROL_NS(void) { uint32_t result; + __ASM volatile ("MRS %0, control_ns" : "=r" (result) ); return (result); } @@ -97,19 +172,19 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_CONTROL_NS(void \details Writes the given value to the Control Register. \param [in] control Control Register value to set */ -__attribute__((always_inline)) __STATIC_INLINE void __set_CONTROL(uint32_t control) +__STATIC_FORCEINLINE void __set_CONTROL(uint32_t control) { __ASM volatile ("MSR control, %0" : : "r" (control) : "memory"); } -#if (__ARM_FEATURE_CMSE == 3U) +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) /** \brief Set Control Register (non-secure) \details Writes the given value to the non-secure Control Register when in secure state. \param [in] control Control Register value to set */ -__attribute__((always_inline)) __STATIC_INLINE void __TZ_set_CONTROL_NS(uint32_t control) +__STATIC_FORCEINLINE void __TZ_set_CONTROL_NS(uint32_t control) { __ASM volatile ("MSR control_ns, %0" : : "r" (control) : "memory"); } @@ -121,27 +196,13 @@ __attribute__((always_inline)) __STATIC_INLINE void __TZ_set_CONTROL_NS(uint32_t \details Returns the content of the IPSR Register. \return IPSR Register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __get_IPSR(void) +__STATIC_FORCEINLINE uint32_t __get_IPSR(void) { uint32_t result; - __ASM volatile ("MRS %0, ipsr" : "=r" (result) ); - return (result); -} - -#if (__ARM_FEATURE_CMSE == 3U) -/** - \brief Get IPSR Register (non-secure) - \details Returns the content of the non-secure IPSR Register when in secure state. - \return IPSR Register value - */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_IPSR_NS(void) -{ - uint32_t result; - __ASM volatile ("MRS %0, ipsr_ns" : "=r" (result) ); + __ASM volatile ("MRS %0, ipsr" : "=r" (result) ); return (result); } -#endif /** @@ -149,27 +210,13 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_IPSR_NS(void) \details Returns the content of the APSR Register. \return APSR Register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __get_APSR(void) +__STATIC_FORCEINLINE uint32_t __get_APSR(void) { uint32_t result; - __ASM volatile ("MRS %0, apsr" : "=r" (result) ); - return (result); -} - -#if (__ARM_FEATURE_CMSE == 3U) -/** - \brief Get APSR Register (non-secure) - \details Returns the content of the non-secure APSR Register when in secure state. - \return APSR Register value - */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_APSR_NS(void) -{ - uint32_t result; - __ASM volatile ("MRS %0, apsr_ns" : "=r" (result) ); + __ASM volatile ("MRS %0, apsr" : "=r" (result) ); return (result); } -#endif /** @@ -177,27 +224,13 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_APSR_NS(void) \details Returns the content of the xPSR Register. \return xPSR Register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __get_xPSR(void) +__STATIC_FORCEINLINE uint32_t __get_xPSR(void) { uint32_t result; - __ASM volatile ("MRS %0, xpsr" : "=r" (result) ); - return (result); -} - -#if (__ARM_FEATURE_CMSE == 3U) -/** - \brief Get xPSR Register (non-secure) - \details Returns the content of the non-secure xPSR Register when in secure state. - \return xPSR Register value - */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_xPSR_NS(void) -{ - uint32_t result; - __ASM volatile ("MRS %0, xpsr_ns" : "=r" (result) ); + __ASM volatile ("MRS %0, xpsr" : "=r" (result) ); return (result); } -#endif /** @@ -205,23 +238,25 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_xPSR_NS(void) \details Returns the current value of the Process Stack Pointer (PSP). \return PSP Register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __get_PSP(void) +__STATIC_FORCEINLINE uint32_t __get_PSP(void) { - register uint32_t result; + uint32_t result; + __ASM volatile ("MRS %0, psp" : "=r" (result) ); return (result); } -#if (__ARM_FEATURE_CMSE == 3U) +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) /** \brief Get Process Stack Pointer (non-secure) \details Returns the current value of the non-secure Process Stack Pointer (PSP) when in secure state. \return PSP Register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_PSP_NS(void) +__STATIC_FORCEINLINE uint32_t __TZ_get_PSP_NS(void) { - register uint32_t result; + uint32_t result; + __ASM volatile ("MRS %0, psp_ns" : "=r" (result) ); return (result); } @@ -233,21 +268,21 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_PSP_NS(void) \details Assigns the given value to the Process Stack Pointer (PSP). \param [in] topOfProcStack Process Stack Pointer value to set */ -__attribute__((always_inline)) __STATIC_INLINE void __set_PSP(uint32_t topOfProcStack) +__STATIC_FORCEINLINE void __set_PSP(uint32_t topOfProcStack) { - __ASM volatile ("MSR psp, %0" : : "r" (topOfProcStack) : "sp"); + __ASM volatile ("MSR psp, %0" : : "r" (topOfProcStack) : ); } -#if (__ARM_FEATURE_CMSE == 3U) +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) /** \brief Set Process Stack Pointer (non-secure) \details Assigns the given value to the non-secure Process Stack Pointer (PSP) when in secure state. \param [in] topOfProcStack Process Stack Pointer value to set */ -__attribute__((always_inline)) __STATIC_INLINE void __TZ_set_PSP_NS(uint32_t topOfProcStack) +__STATIC_FORCEINLINE void __TZ_set_PSP_NS(uint32_t topOfProcStack) { - __ASM volatile ("MSR psp_ns, %0" : : "r" (topOfProcStack) : "sp"); + __ASM volatile ("MSR psp_ns, %0" : : "r" (topOfProcStack) : ); } #endif @@ -257,23 +292,25 @@ __attribute__((always_inline)) __STATIC_INLINE void __TZ_set_PSP_NS(uint32_t top \details Returns the current value of the Main Stack Pointer (MSP). \return MSP Register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __get_MSP(void) +__STATIC_FORCEINLINE uint32_t __get_MSP(void) { - register uint32_t result; + uint32_t result; + __ASM volatile ("MRS %0, msp" : "=r" (result) ); return (result); } -#if (__ARM_FEATURE_CMSE == 3U) +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) /** \brief Get Main Stack Pointer (non-secure) \details Returns the current value of the non-secure Main Stack Pointer (MSP) when in secure state. \return MSP Register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_MSP_NS(void) +__STATIC_FORCEINLINE uint32_t __TZ_get_MSP_NS(void) { - register uint32_t result; + uint32_t result; + __ASM volatile ("MRS %0, msp_ns" : "=r" (result) ); return (result); } @@ -285,21 +322,48 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_MSP_NS(void) \details Assigns the given value to the Main Stack Pointer (MSP). \param [in] topOfMainStack Main Stack Pointer value to set */ -__attribute__((always_inline)) __STATIC_INLINE void __set_MSP(uint32_t topOfMainStack) +__STATIC_FORCEINLINE void __set_MSP(uint32_t topOfMainStack) { - __ASM volatile ("MSR msp, %0" : : "r" (topOfMainStack) : "sp"); + __ASM volatile ("MSR msp, %0" : : "r" (topOfMainStack) : ); } -#if (__ARM_FEATURE_CMSE == 3U) +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) /** \brief Set Main Stack Pointer (non-secure) \details Assigns the given value to the non-secure Main Stack Pointer (MSP) when in secure state. \param [in] topOfMainStack Main Stack Pointer value to set */ -__attribute__((always_inline)) __STATIC_INLINE void __TZ_set_MSP_NS(uint32_t topOfMainStack) +__STATIC_FORCEINLINE void __TZ_set_MSP_NS(uint32_t topOfMainStack) { - __ASM volatile ("MSR msp_ns, %0" : : "r" (topOfMainStack) : "sp"); + __ASM volatile ("MSR msp_ns, %0" : : "r" (topOfMainStack) : ); +} +#endif + + +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Get Stack Pointer (non-secure) + \details Returns the current value of the non-secure Stack Pointer (SP) when in secure state. + \return SP Register value + */ +__STATIC_FORCEINLINE uint32_t __TZ_get_SP_NS(void) +{ + uint32_t result; + + __ASM volatile ("MRS %0, sp_ns" : "=r" (result) ); + return (result); +} + + +/** + \brief Set Stack Pointer (non-secure) + \details Assigns the given value to the non-secure Stack Pointer (SP) when in secure state. + \param [in] topOfStack Stack Pointer value to set + */ +__STATIC_FORCEINLINE void __TZ_set_SP_NS(uint32_t topOfStack) +{ + __ASM volatile ("MSR sp_ns, %0" : : "r" (topOfStack) : ); } #endif @@ -309,23 +373,25 @@ __attribute__((always_inline)) __STATIC_INLINE void __TZ_set_MSP_NS(uint32_t top \details Returns the current state of the priority mask bit from the Priority Mask Register. \return Priority Mask value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __get_PRIMASK(void) +__STATIC_FORCEINLINE uint32_t __get_PRIMASK(void) { uint32_t result; + __ASM volatile ("MRS %0, primask" : "=r" (result) ); return (result); } -#if (__ARM_FEATURE_CMSE == 3U) +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) /** \brief Get Priority Mask (non-secure) \details Returns the current state of the non-secure priority mask bit from the Priority Mask Register when in secure state. \return Priority Mask value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_PRIMASK_NS(void) +__STATIC_FORCEINLINE uint32_t __TZ_get_PRIMASK_NS(void) { uint32_t result; + __ASM volatile ("MRS %0, primask_ns" : "=r" (result) ); return (result); } @@ -337,36 +403,34 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_PRIMASK_NS(void \details Assigns the given value to the Priority Mask Register. \param [in] priMask Priority Mask */ -__attribute__((always_inline)) __STATIC_INLINE void __set_PRIMASK(uint32_t priMask) +__STATIC_FORCEINLINE void __set_PRIMASK(uint32_t priMask) { __ASM volatile ("MSR primask, %0" : : "r" (priMask) : "memory"); } -#if (__ARM_FEATURE_CMSE == 3U) +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) /** \brief Set Priority Mask (non-secure) \details Assigns the given value to the non-secure Priority Mask Register when in secure state. \param [in] priMask Priority Mask */ -__attribute__((always_inline)) __STATIC_INLINE void __TZ_set_PRIMASK_NS(uint32_t priMask) +__STATIC_FORCEINLINE void __TZ_set_PRIMASK_NS(uint32_t priMask) { __ASM volatile ("MSR primask_ns, %0" : : "r" (priMask) : "memory"); } #endif -#if ((__ARM_ARCH_7M__ == 1U) || (__ARM_ARCH_7EM__ == 1U) || (__ARM_ARCH_8M__ == 1U)) /* ToDo: ARMCC_V6: check if this is ok for cortex >=3 */ - +#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__ ) && (__ARM_ARCH_7EM__ == 1)) || \ + (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) ) /** \brief Enable FIQ \details Enables FIQ interrupts by clearing the F-bit in the CPSR. Can only be executed in Privileged modes. */ -__attribute__((always_inline)) __STATIC_INLINE void __enable_fault_irq(void) -{ - __ASM volatile ("cpsie f" : : : "memory"); -} +#define __enable_fault_irq __enable_fiq /* see arm_compat.h */ /** @@ -374,10 +438,7 @@ __attribute__((always_inline)) __STATIC_INLINE void __enable_fault_irq(void) \details Disables FIQ interrupts by setting the F-bit in the CPSR. Can only be executed in Privileged modes. */ -__attribute__((always_inline)) __STATIC_INLINE void __disable_fault_irq(void) -{ - __ASM volatile ("cpsid f" : : : "memory"); -} +#define __disable_fault_irq __disable_fiq /* see arm_compat.h */ /** @@ -385,23 +446,25 @@ __attribute__((always_inline)) __STATIC_INLINE void __disable_fault_irq(void) \details Returns the current value of the Base Priority register. \return Base Priority register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __get_BASEPRI(void) +__STATIC_FORCEINLINE uint32_t __get_BASEPRI(void) { uint32_t result; + __ASM volatile ("MRS %0, basepri" : "=r" (result) ); return (result); } -#if (__ARM_FEATURE_CMSE == 3U) +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) /** \brief Get Base Priority (non-secure) \details Returns the current value of the non-secure Base Priority register when in secure state. \return Base Priority register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_BASEPRI_NS(void) +__STATIC_FORCEINLINE uint32_t __TZ_get_BASEPRI_NS(void) { uint32_t result; + __ASM volatile ("MRS %0, basepri_ns" : "=r" (result) ); return (result); } @@ -413,21 +476,21 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_BASEPRI_NS(void \details Assigns the given value to the Base Priority register. \param [in] basePri Base Priority value to set */ -__attribute__((always_inline)) __STATIC_INLINE void __set_BASEPRI(uint32_t value) +__STATIC_FORCEINLINE void __set_BASEPRI(uint32_t basePri) { - __ASM volatile ("MSR basepri, %0" : : "r" (value) : "memory"); + __ASM volatile ("MSR basepri, %0" : : "r" (basePri) : "memory"); } -#if (__ARM_FEATURE_CMSE == 3U) +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) /** \brief Set Base Priority (non-secure) \details Assigns the given value to the non-secure Base Priority register when in secure state. \param [in] basePri Base Priority value to set */ -__attribute__((always_inline)) __STATIC_INLINE void __TZ_set_BASEPRI_NS(uint32_t value) +__STATIC_FORCEINLINE void __TZ_set_BASEPRI_NS(uint32_t basePri) { - __ASM volatile ("MSR basepri_ns, %0" : : "r" (value) : "memory"); + __ASM volatile ("MSR basepri_ns, %0" : : "r" (basePri) : "memory"); } #endif @@ -438,48 +501,36 @@ __attribute__((always_inline)) __STATIC_INLINE void __TZ_set_BASEPRI_NS(uint32_t or the new value increases the BASEPRI priority level. \param [in] basePri Base Priority value to set */ -__attribute__((always_inline)) __STATIC_INLINE void __set_BASEPRI_MAX(uint32_t value) +__STATIC_FORCEINLINE void __set_BASEPRI_MAX(uint32_t basePri) { - __ASM volatile ("MSR basepri_max, %0" : : "r" (value) : "memory"); + __ASM volatile ("MSR basepri_max, %0" : : "r" (basePri) : "memory"); } -#if (__ARM_FEATURE_CMSE == 3U) -/** - \brief Set Base Priority with condition (non_secure) - \details Assigns the given value to the non-secure Base Priority register when in secure state only if BASEPRI masking is disabled, - or the new value increases the BASEPRI priority level. - \param [in] basePri Base Priority value to set - */ -__attribute__((always_inline)) __STATIC_INLINE void __TZ_set_BASEPRI_MAX_NS(uint32_t value) -{ - __ASM volatile ("MSR basepri_max_ns, %0" : : "r" (value) : "memory"); -} -#endif - - /** \brief Get Fault Mask \details Returns the current value of the Fault Mask register. \return Fault Mask register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __get_FAULTMASK(void) +__STATIC_FORCEINLINE uint32_t __get_FAULTMASK(void) { uint32_t result; + __ASM volatile ("MRS %0, faultmask" : "=r" (result) ); return (result); } -#if (__ARM_FEATURE_CMSE == 3U) +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) /** \brief Get Fault Mask (non-secure) \details Returns the current value of the non-secure Fault Mask register when in secure state. \return Fault Mask register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_FAULTMASK_NS(void) +__STATIC_FORCEINLINE uint32_t __TZ_get_FAULTMASK_NS(void) { uint32_t result; + __ASM volatile ("MRS %0, faultmask_ns" : "=r" (result) ); return (result); } @@ -491,216 +542,233 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_FAULTMASK_NS(vo \details Assigns the given value to the Fault Mask register. \param [in] faultMask Fault Mask value to set */ -__attribute__((always_inline)) __STATIC_INLINE void __set_FAULTMASK(uint32_t faultMask) +__STATIC_FORCEINLINE void __set_FAULTMASK(uint32_t faultMask) { __ASM volatile ("MSR faultmask, %0" : : "r" (faultMask) : "memory"); } -#if (__ARM_FEATURE_CMSE == 3U) +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) /** \brief Set Fault Mask (non-secure) \details Assigns the given value to the non-secure Fault Mask register when in secure state. \param [in] faultMask Fault Mask value to set */ -__attribute__((always_inline)) __STATIC_INLINE void __TZ_set_FAULTMASK_NS(uint32_t faultMask) +__STATIC_FORCEINLINE void __TZ_set_FAULTMASK_NS(uint32_t faultMask) { __ASM volatile ("MSR faultmask_ns, %0" : : "r" (faultMask) : "memory"); } #endif +#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__ ) && (__ARM_ARCH_7EM__ == 1)) || \ + (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) ) */ -#endif /* ((__ARM_ARCH_7M__ == 1U) || (__ARM_ARCH_8M__ == 1U)) */ - -#if (__ARM_ARCH_8M__ == 1U) +#if ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \ + (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1)) ) /** \brief Get Process Stack Pointer Limit + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence zero is returned always in non-secure + mode. + \details Returns the current value of the Process Stack Pointer Limit (PSPLIM). \return PSPLIM Register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __get_PSPLIM(void) +__STATIC_FORCEINLINE uint32_t __get_PSPLIM(void) { - register uint32_t result; +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3))) + // without main extensions, the non-secure PSPLIM is RAZ/WI + return 0U; +#else + uint32_t result; __ASM volatile ("MRS %0, psplim" : "=r" (result) ); - return (result); + return result; +#endif } - -#if (__ARM_FEATURE_CMSE == 3U) && (__ARM_ARCH_PROFILE == 'M') /* ToDo: ARMCC_V6: check predefined macro for mainline */ +#if (defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3)) /** \brief Get Process Stack Pointer Limit (non-secure) + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence zero is returned always in non-secure + mode. + \details Returns the current value of the non-secure Process Stack Pointer Limit (PSPLIM) when in secure state. \return PSPLIM Register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_PSPLIM_NS(void) +__STATIC_FORCEINLINE uint32_t __TZ_get_PSPLIM_NS(void) { - register uint32_t result; +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1))) + // without main extensions, the non-secure PSPLIM is RAZ/WI + return 0U; +#else + uint32_t result; __ASM volatile ("MRS %0, psplim_ns" : "=r" (result) ); - return (result); + return result; +#endif } #endif /** \brief Set Process Stack Pointer Limit + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence the write is silently ignored in non-secure + mode. + \details Assigns the given value to the Process Stack Pointer Limit (PSPLIM). \param [in] ProcStackPtrLimit Process Stack Pointer Limit value to set */ -__attribute__((always_inline)) __STATIC_INLINE void __set_PSPLIM(uint32_t ProcStackPtrLimit) +__STATIC_FORCEINLINE void __set_PSPLIM(uint32_t ProcStackPtrLimit) { +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3))) + // without main extensions, the non-secure PSPLIM is RAZ/WI + (void)ProcStackPtrLimit; +#else __ASM volatile ("MSR psplim, %0" : : "r" (ProcStackPtrLimit)); +#endif } -#if (__ARM_FEATURE_CMSE == 3U) && (__ARM_ARCH_PROFILE == 'M') /* ToDo: ARMCC_V6: check predefined macro for mainline */ +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) /** \brief Set Process Stack Pointer (non-secure) + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence the write is silently ignored in non-secure + mode. + \details Assigns the given value to the non-secure Process Stack Pointer Limit (PSPLIM) when in secure state. \param [in] ProcStackPtrLimit Process Stack Pointer Limit value to set */ -__attribute__((always_inline)) __STATIC_INLINE void __TZ_set_PSPLIM_NS(uint32_t ProcStackPtrLimit) +__STATIC_FORCEINLINE void __TZ_set_PSPLIM_NS(uint32_t ProcStackPtrLimit) { +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1))) + // without main extensions, the non-secure PSPLIM is RAZ/WI + (void)ProcStackPtrLimit; +#else __ASM volatile ("MSR psplim_ns, %0\n" : : "r" (ProcStackPtrLimit)); +#endif } #endif /** \brief Get Main Stack Pointer Limit + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence zero is returned always. + \details Returns the current value of the Main Stack Pointer Limit (MSPLIM). \return MSPLIM Register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __get_MSPLIM(void) +__STATIC_FORCEINLINE uint32_t __get_MSPLIM(void) { - register uint32_t result; +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3))) + // without main extensions, the non-secure MSPLIM is RAZ/WI + return 0U; +#else + uint32_t result; __ASM volatile ("MRS %0, msplim" : "=r" (result) ); - return (result); + return result; +#endif } -#if (__ARM_FEATURE_CMSE == 3U) && (__ARM_ARCH_PROFILE == 'M') /* ToDo: ARMCC_V6: check predefined macro for mainline */ +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) /** \brief Get Main Stack Pointer Limit (non-secure) + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence zero is returned always. + \details Returns the current value of the non-secure Main Stack Pointer Limit(MSPLIM) when in secure state. \return MSPLIM Register value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_MSPLIM_NS(void) +__STATIC_FORCEINLINE uint32_t __TZ_get_MSPLIM_NS(void) { - register uint32_t result; +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1))) + // without main extensions, the non-secure MSPLIM is RAZ/WI + return 0U; +#else + uint32_t result; __ASM volatile ("MRS %0, msplim_ns" : "=r" (result) ); - return (result); + return result; +#endif } #endif /** \brief Set Main Stack Pointer Limit + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence the write is silently ignored. + \details Assigns the given value to the Main Stack Pointer Limit (MSPLIM). \param [in] MainStackPtrLimit Main Stack Pointer Limit value to set */ -__attribute__((always_inline)) __STATIC_INLINE void __set_MSPLIM(uint32_t MainStackPtrLimit) +__STATIC_FORCEINLINE void __set_MSPLIM(uint32_t MainStackPtrLimit) { +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3))) + // without main extensions, the non-secure MSPLIM is RAZ/WI + (void)MainStackPtrLimit; +#else __ASM volatile ("MSR msplim, %0" : : "r" (MainStackPtrLimit)); +#endif } -#if (__ARM_FEATURE_CMSE == 3U) && (__ARM_ARCH_PROFILE == 'M') /* ToDo: ARMCC_V6: check predefined macro for mainline */ +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) /** \brief Set Main Stack Pointer Limit (non-secure) + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence the write is silently ignored. + \details Assigns the given value to the non-secure Main Stack Pointer Limit (MSPLIM) when in secure state. \param [in] MainStackPtrLimit Main Stack Pointer value to set */ -__attribute__((always_inline)) __STATIC_INLINE void __TZ_set_MSPLIM_NS(uint32_t MainStackPtrLimit) +__STATIC_FORCEINLINE void __TZ_set_MSPLIM_NS(uint32_t MainStackPtrLimit) { +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1))) + // without main extensions, the non-secure MSPLIM is RAZ/WI + (void)MainStackPtrLimit; +#else __ASM volatile ("MSR msplim_ns, %0" : : "r" (MainStackPtrLimit)); +#endif } #endif -#endif /* (__ARM_ARCH_8M__ == 1U) */ - - -#if ((__ARM_ARCH_7EM__ == 1U) || (__ARM_ARCH_8M__ == 1U)) /* ToDo: ARMCC_V6: check if this is ok for cortex >=4 */ +#endif /* ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \ + (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1)) ) */ /** \brief Get FPSCR - \details eturns the current value of the Floating Point Status/Control register. + \details Returns the current value of the Floating Point Status/Control register. \return Floating Point Status/Control register value */ -#define __get_FPSCR __builtin_arm_get_fpscr -#if 0 -__attribute__((always_inline)) __STATIC_INLINE uint32_t __get_FPSCR(void) -{ -#if (__FPU_PRESENT == 1U) && (__FPU_USED == 1U) - uint32_t result; - __ASM volatile (""); /* Empty asm statement works as a scheduling barrier */ - __ASM volatile ("VMRS %0, fpscr" : "=r" (result) ); - __ASM volatile (""); - return (result); +#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \ + (defined (__FPU_USED ) && (__FPU_USED == 1U)) ) +#define __get_FPSCR (uint32_t)__builtin_arm_get_fpscr #else - return (0); +#define __get_FPSCR() ((uint32_t)0U) #endif -} -#endif - -#if (__ARM_FEATURE_CMSE == 3U) -/** - \brief Get FPSCR (non-secure) - \details Returns the current value of the non-secure Floating Point Status/Control register when in secure state. - \return Floating Point Status/Control register value - */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __TZ_get_FPSCR_NS(void) -{ -#if (__FPU_PRESENT == 1U) && (__FPU_USED == 1U) - uint32_t result; - __ASM volatile (""); /* Empty asm statement works as a scheduling barrier */ - __ASM volatile ("VMRS %0, fpscr_ns" : "=r" (result) ); - __ASM volatile (""); - return (result); -#else - return (0); -#endif -} -#endif - /** \brief Set FPSCR \details Assigns the given value to the Floating Point Status/Control register. \param [in] fpscr Floating Point Status/Control value to set */ +#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \ + (defined (__FPU_USED ) && (__FPU_USED == 1U)) ) #define __set_FPSCR __builtin_arm_set_fpscr -#if 0 -__attribute__((always_inline)) __STATIC_INLINE void __set_FPSCR(uint32_t fpscr) -{ -#if (__FPU_PRESENT == 1U) && (__FPU_USED == 1U) - __ASM volatile (""); /* Empty asm statement works as a scheduling barrier */ - __ASM volatile ("VMSR fpscr, %0" : : "r" (fpscr) : "vfpcc"); - __ASM volatile (""); -#endif -} -#endif - -#if (__ARM_FEATURE_CMSE == 3U) -/** - \brief Set FPSCR (non-secure) - \details Assigns the given value to the non-secure Floating Point Status/Control register when in secure state. - \param [in] fpscr Floating Point Status/Control value to set - */ -__attribute__((always_inline)) __STATIC_INLINE void __TZ_set_FPSCR_NS(uint32_t fpscr) -{ -#if (__FPU_PRESENT == 1U) && (__FPU_USED == 1U) - __ASM volatile (""); /* Empty asm statement works as a scheduling barrier */ - __ASM volatile ("VMSR fpscr_ns, %0" : : "r" (fpscr) : "vfpcc"); - __ASM volatile (""); -#endif -} +#else +#define __set_FPSCR(x) ((void)(x)) #endif -#endif /* ((__ARM_ARCH_7EM__ == 1U) || (__ARM_ARCH_8M__ == 1U)) */ - - /*@} end of CMSIS_Core_RegAccFunctions */ @@ -776,43 +844,29 @@ __attribute__((always_inline)) __STATIC_INLINE void __TZ_set_FPSCR_NS(uint32_t f /** \brief Reverse byte order (32 bit) - \details Reverses the byte order in integer value. + \details Reverses the byte order in unsigned integer value. For example, 0x12345678 becomes 0x78563412. \param [in] value Value to reverse \return Reversed value */ -#define __REV __builtin_bswap32 +#define __REV(value) __builtin_bswap32(value) /** \brief Reverse byte order (16 bit) - \details Reverses the byte order in two unsigned short values. + \details Reverses the byte order within each halfword of a word. For example, 0x12345678 becomes 0x34127856. \param [in] value Value to reverse \return Reversed value */ -#define __REV16 __builtin_bswap16 /* ToDo: ARMCC_V6: check if __builtin_bswap16 could be used */ -#if 0 -__attribute__((always_inline)) __STATIC_INLINE uint32_t __REV16(uint32_t value) -{ - uint32_t result; - __ASM volatile ("rev16 %0, %1" : __CMSIS_GCC_OUT_REG (result) : __CMSIS_GCC_USE_REG (value) ); - return (result); -} -#endif +#define __REV16(value) __ROR(__REV(value), 16) /** - \brief Reverse byte order in signed short value - \details Reverses the byte order in a signed short value with sign extension to integer. + \brief Reverse byte order (16 bit) + \details Reverses the byte order in a 16-bit value and returns the signed 16-bit result. For example, 0x0080 becomes 0x8000. \param [in] value Value to reverse \return Reversed value */ -/* ToDo: ARMCC_V6: check if __builtin_bswap16 could be used */ -__attribute__((always_inline)) __STATIC_INLINE int32_t __REVSH(int32_t value) -{ - int32_t result; - __ASM volatile ("revsh %0, %1" : __CMSIS_GCC_OUT_REG (result) : __CMSIS_GCC_USE_REG (value) ); - return (result); -} +#define __REVSH(value) (int16_t)__builtin_bswap16(value) /** @@ -822,8 +876,15 @@ __attribute__((always_inline)) __STATIC_INLINE int32_t __REVSH(int32_t value) \param [in] op2 Number of Bits to rotate \return Rotated value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __ROR(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __ROR(uint32_t op1, uint32_t op2) { + op2 %= 32U; + + if (op2 == 0U) + { + return op1; + } + return (op1 >> op2) | (op1 << (32U - op2)); } @@ -831,11 +892,11 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __ROR(uint32_t op1, uint /** \brief Breakpoint \details Causes the processor to enter Debug state. - Debug tools can use this to investigate system state when the instruction at a particular address is reached. - \param [in] value is ignored by the processor. - If required, a debugger can use it to store additional information about the breakpoint. + Debug tools can use this to investigate system state when the instruction at a particular address is reached. + \param [in] value is ignored by the processor. + If required, a debugger can use it to store additional information about the breakpoint. */ -#define __BKPT(value) __ASM volatile ("bkpt "#value) +#define __BKPT(value) __ASM volatile ("bkpt "#value) /** @@ -844,28 +905,7 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __ROR(uint32_t op1, uint \param [in] value Value to reverse \return Reversed value */ -/* ToDo: ARMCC_V6: check if __builtin_arm_rbit is supported */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value) -{ - uint32_t result; -#if ((__ARM_ARCH_7M__ == 1U) || (__ARM_ARCH_7EM__ == 1U) || (__ARM_ARCH_8M__ == 1U)) /* ToDo: ARMCC_V6: check if this is ok for cortex >=3 */ - __ASM volatile ("rbit %0, %1" : "=r" (result) : "r" (value) ); -#else - int32_t s = 4 /*sizeof(v)*/ * 8 - 1; /* extra shift needed at end */ - result = value; /* r will be reversed bits of v; first get LSB of v */ - - for (value >>= 1U; value; value >>= 1U) - { - result <<= 1U; - result |= value & 1U; - s--; - } - - result <<= s; /* shift when v's highest bits are zero */ -#endif - return (result); -} - +#define __RBIT __builtin_arm_rbit /** \brief Count leading zeros @@ -873,11 +913,13 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value) \param [in] value Value to count the leading zeros \return number of leading zeros in value */ -#define __CLZ __builtin_clz - +#define __CLZ (uint8_t)__builtin_clz -#if ((__ARM_ARCH_7M__ == 1U) || (__ARM_ARCH_7EM__ == 1U) || (__ARM_ARCH_8M__ == 1U)) /* ToDo: ARMCC_V6: check if this is ok for cortex >=3 */ +#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__ ) && (__ARM_ARCH_7EM__ == 1)) || \ + (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \ + (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1)) ) /** \brief LDR Exclusive (8 bit) \details Executes a exclusive LDR instruction for 8 bit value. @@ -944,6 +986,15 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value) */ #define __CLREX __builtin_arm_clrex +#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__ ) && (__ARM_ARCH_7EM__ == 1)) || \ + (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \ + (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1)) ) */ + + +#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__ ) && (__ARM_ARCH_7EM__ == 1)) || \ + (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) ) /** \brief Signed Saturate @@ -952,13 +1003,7 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value) \param [in] sat Bit position to saturate to (1..32) \return Saturated value */ -/*#define __SSAT __builtin_arm_ssat*/ -#define __SSAT(ARG1,ARG2) \ -({ \ - int32_t __RES, __ARG1 = (ARG1); \ - __ASM ("ssat %0, %1, %2" : "=r" (__RES) : "I" (ARG2), "r" (__ARG1) ); \ - __RES; \ - }) +#define __SSAT __builtin_arm_ssat /** @@ -969,14 +1014,6 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value) \return Saturated value */ #define __USAT __builtin_arm_usat -#if 0 -#define __USAT(ARG1,ARG2) \ -({ \ - uint32_t __RES, __ARG1 = (ARG1); \ - __ASM ("usat %0, %1, %2" : "=r" (__RES) : "I" (ARG2), "r" (__ARG1) ); \ - __RES; \ - }) -#endif /** @@ -986,9 +1023,10 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value) \param [in] value Value to rotate \return Rotated value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __RRX(uint32_t value) +__STATIC_FORCEINLINE uint32_t __RRX(uint32_t value) { uint32_t result; + __ASM volatile ("rrx %0, %1" : __CMSIS_GCC_OUT_REG (result) : __CMSIS_GCC_USE_REG (value) ); return (result); } @@ -1000,9 +1038,10 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __RRX(uint32_t value) \param [in] ptr Pointer to data \return value of type uint8_t at (*ptr) */ -__attribute__((always_inline)) __STATIC_INLINE uint8_t __LDRBT(volatile uint8_t* ptr) +__STATIC_FORCEINLINE uint8_t __LDRBT(volatile uint8_t* ptr) { uint32_t result; + __ASM volatile ("ldrbt %0, %1" : "=r" (result) : "Q" (*ptr) ); return ((uint8_t) result); /* Add explicit type cast here */ } @@ -1014,9 +1053,10 @@ __attribute__((always_inline)) __STATIC_INLINE uint8_t __LDRBT(volatile uint8_t* \param [in] ptr Pointer to data \return value of type uint16_t at (*ptr) */ -__attribute__((always_inline)) __STATIC_INLINE uint16_t __LDRHT(volatile uint16_t* ptr) +__STATIC_FORCEINLINE uint16_t __LDRHT(volatile uint16_t* ptr) { uint32_t result; + __ASM volatile ("ldrht %0, %1" : "=r" (result) : "Q" (*ptr) ); return ((uint16_t) result); /* Add explicit type cast here */ } @@ -1028,9 +1068,10 @@ __attribute__((always_inline)) __STATIC_INLINE uint16_t __LDRHT(volatile uint16_ \param [in] ptr Pointer to data \return value of type uint32_t at (*ptr) */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __LDRT(volatile uint32_t* ptr) +__STATIC_FORCEINLINE uint32_t __LDRT(volatile uint32_t* ptr) { uint32_t result; + __ASM volatile ("ldrt %0, %1" : "=r" (result) : "Q" (*ptr) ); return (result); } @@ -1042,7 +1083,7 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __LDRT(volatile uint32_t \param [in] value Value to store \param [in] ptr Pointer to location */ -__attribute__((always_inline)) __STATIC_INLINE void __STRBT(uint8_t value, volatile uint8_t* ptr) +__STATIC_FORCEINLINE void __STRBT(uint8_t value, volatile uint8_t* ptr) { __ASM volatile ("strbt %1, %0" : "=Q" (*ptr) : "r" ((uint32_t)value) ); } @@ -1054,7 +1095,7 @@ __attribute__((always_inline)) __STATIC_INLINE void __STRBT(uint8_t value, volat \param [in] value Value to store \param [in] ptr Pointer to location */ -__attribute__((always_inline)) __STATIC_INLINE void __STRHT(uint16_t value, volatile uint16_t* ptr) +__STATIC_FORCEINLINE void __STRHT(uint16_t value, volatile uint16_t* ptr) { __ASM volatile ("strht %1, %0" : "=Q" (*ptr) : "r" ((uint32_t)value) ); } @@ -1066,25 +1107,85 @@ __attribute__((always_inline)) __STATIC_INLINE void __STRHT(uint16_t value, vola \param [in] value Value to store \param [in] ptr Pointer to location */ -__attribute__((always_inline)) __STATIC_INLINE void __STRT(uint32_t value, volatile uint32_t* ptr) +__STATIC_FORCEINLINE void __STRT(uint32_t value, volatile uint32_t* ptr) { __ASM volatile ("strt %1, %0" : "=Q" (*ptr) : "r" (value) ); } -#endif /* ((__ARM_ARCH_7M__ == 1U) || (__ARM_ARCH_7EM__ == 1U) || (__ARM_ARCH_8M__ == 1U)) */ +#else /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__ ) && (__ARM_ARCH_7EM__ == 1)) || \ + (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) ) */ +/** + \brief Signed Saturate + \details Saturates a signed value. + \param [in] value Value to be saturated + \param [in] sat Bit position to saturate to (1..32) + \return Saturated value + */ +__STATIC_FORCEINLINE int32_t __SSAT(int32_t val, uint32_t sat) +{ + if ((sat >= 1U) && (sat <= 32U)) + { + const int32_t max = (int32_t)((1U << (sat - 1U)) - 1U); + const int32_t min = -1 - max ; + + if (val > max) + { + return max; + } + else if (val < min) + { + return min; + } + } -#if (__ARM_ARCH_8M__ == 1U) + return val; +} +/** + \brief Unsigned Saturate + \details Saturates an unsigned value. + \param [in] value Value to be saturated + \param [in] sat Bit position to saturate to (0..31) + \return Saturated value + */ +__STATIC_FORCEINLINE uint32_t __USAT(int32_t val, uint32_t sat) +{ + if (sat <= 31U) + { + const uint32_t max = ((1U << sat) - 1U); + + if (val > (int32_t)max) + { + return max; + } + else if (val < 0) + { + return 0U; + } + } + + return (uint32_t)val; +} + +#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__ ) && (__ARM_ARCH_7EM__ == 1)) || \ + (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) ) */ + + +#if ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \ + (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1)) ) /** \brief Load-Acquire (8 bit) \details Executes a LDAB instruction for 8 bit value. \param [in] ptr Pointer to data \return value of type uint8_t at (*ptr) */ -__attribute__((always_inline)) __STATIC_INLINE uint8_t __LDAB(volatile uint8_t* ptr) +__STATIC_FORCEINLINE uint8_t __LDAB(volatile uint8_t* ptr) { uint32_t result; + __ASM volatile ("ldab %0, %1" : "=r" (result) : "Q" (*ptr) ); return ((uint8_t) result); } @@ -1096,9 +1197,10 @@ __attribute__((always_inline)) __STATIC_INLINE uint8_t __LDAB(volatile uint8_t* \param [in] ptr Pointer to data \return value of type uint16_t at (*ptr) */ -__attribute__((always_inline)) __STATIC_INLINE uint16_t __LDAH(volatile uint16_t* ptr) +__STATIC_FORCEINLINE uint16_t __LDAH(volatile uint16_t* ptr) { uint32_t result; + __ASM volatile ("ldah %0, %1" : "=r" (result) : "Q" (*ptr) ); return ((uint16_t) result); } @@ -1110,9 +1212,10 @@ __attribute__((always_inline)) __STATIC_INLINE uint16_t __LDAH(volatile uint16_t \param [in] ptr Pointer to data \return value of type uint32_t at (*ptr) */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __LDA(volatile uint32_t* ptr) +__STATIC_FORCEINLINE uint32_t __LDA(volatile uint32_t* ptr) { uint32_t result; + __ASM volatile ("lda %0, %1" : "=r" (result) : "Q" (*ptr) ); return (result); } @@ -1124,7 +1227,7 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __LDA(volatile uint32_t* \param [in] value Value to store \param [in] ptr Pointer to location */ -__attribute__((always_inline)) __STATIC_INLINE void __STLB(uint8_t value, volatile uint8_t* ptr) +__STATIC_FORCEINLINE void __STLB(uint8_t value, volatile uint8_t* ptr) { __ASM volatile ("stlb %1, %0" : "=Q" (*ptr) : "r" ((uint32_t)value) ); } @@ -1136,7 +1239,7 @@ __attribute__((always_inline)) __STATIC_INLINE void __STLB(uint8_t value, volati \param [in] value Value to store \param [in] ptr Pointer to location */ -__attribute__((always_inline)) __STATIC_INLINE void __STLH(uint16_t value, volatile uint16_t* ptr) +__STATIC_FORCEINLINE void __STLH(uint16_t value, volatile uint16_t* ptr) { __ASM volatile ("stlh %1, %0" : "=Q" (*ptr) : "r" ((uint32_t)value) ); } @@ -1148,7 +1251,7 @@ __attribute__((always_inline)) __STATIC_INLINE void __STLH(uint16_t value, volat \param [in] value Value to store \param [in] ptr Pointer to location */ -__attribute__((always_inline)) __STATIC_INLINE void __STL(uint32_t value, volatile uint32_t* ptr) +__STATIC_FORCEINLINE void __STL(uint32_t value, volatile uint32_t* ptr) { __ASM volatile ("stl %1, %0" : "=Q" (*ptr) : "r" ((uint32_t)value) ); } @@ -1213,7 +1316,8 @@ __attribute__((always_inline)) __STATIC_INLINE void __STL(uint32_t value, volati */ #define __STLEX (uint32_t)__builtin_arm_stlex -#endif /* (__ARM_ARCH_8M__ == 1U) */ +#endif /* ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \ + (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1)) ) */ /*@}*/ /* end of group CMSIS_Core_InstructionInterface */ @@ -1224,279 +1328,317 @@ __attribute__((always_inline)) __STATIC_INLINE void __STL(uint32_t value, volati @{ */ -#if (__ARM_FEATURE_DSP == 1U) /* ToDo: ARMCC_V6: This should be ARCH >= ARMv7-M + SIMD */ +#if (defined (__ARM_FEATURE_DSP) && (__ARM_FEATURE_DSP == 1)) -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SADD8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SADD8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("sadd8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __QADD8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __QADD8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("qadd8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SHADD8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SHADD8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("shadd8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UADD8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UADD8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uadd8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UQADD8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UQADD8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uqadd8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UHADD8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UHADD8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uhadd8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SSUB8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SSUB8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("ssub8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __QSUB8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __QSUB8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("qsub8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SHSUB8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SHSUB8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("shsub8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __USUB8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __USUB8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("usub8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UQSUB8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UQSUB8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uqsub8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UHSUB8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UHSUB8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uhsub8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SADD16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SADD16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("sadd16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __QADD16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __QADD16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("qadd16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SHADD16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SHADD16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("shadd16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UADD16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UADD16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uadd16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UQADD16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UQADD16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uqadd16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UHADD16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UHADD16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uhadd16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SSUB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SSUB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("ssub16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __QSUB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __QSUB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("qsub16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SHSUB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SHSUB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("shsub16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __USUB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __USUB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("usub16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UQSUB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UQSUB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uqsub16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UHSUB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UHSUB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uhsub16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SASX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SASX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("sasx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __QASX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __QASX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("qasx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SHASX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SHASX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("shasx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UASX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UASX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uasx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UQASX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UQASX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uqasx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UHASX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UHASX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uhasx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SSAX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SSAX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("ssax %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __QSAX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __QSAX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("qsax %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SHSAX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SHSAX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("shsax %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __USAX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __USAX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("usax %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UQSAX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UQSAX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uqsax %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UHSAX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UHSAX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uhsax %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __USAD8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __USAD8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("usad8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __USADA8(uint32_t op1, uint32_t op2, uint32_t op3) +__STATIC_FORCEINLINE uint32_t __USADA8(uint32_t op1, uint32_t op2, uint32_t op3) { uint32_t result; + __ASM volatile ("usada8 %0, %1, %2, %3" : "=r" (result) : "r" (op1), "r" (op2), "r" (op3) ); return (result); } #define __SSAT16(ARG1,ARG2) \ ({ \ - uint32_t __RES, __ARG1 = (ARG1); \ + int32_t __RES, __ARG1 = (ARG1); \ __ASM ("ssat16 %0, %1, %2" : "=r" (__RES) : "I" (ARG2), "r" (__ARG1) ); \ __RES; \ }) @@ -1508,63 +1650,71 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __USADA8(uint32_t op1, u __RES; \ }) -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UXTB16(uint32_t op1) +__STATIC_FORCEINLINE uint32_t __UXTB16(uint32_t op1) { uint32_t result; + __ASM volatile ("uxtb16 %0, %1" : "=r" (result) : "r" (op1)); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __UXTAB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UXTAB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uxtab16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SXTB16(uint32_t op1) +__STATIC_FORCEINLINE uint32_t __SXTB16(uint32_t op1) { uint32_t result; + __ASM volatile ("sxtb16 %0, %1" : "=r" (result) : "r" (op1)); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SXTAB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SXTAB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("sxtab16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SMUAD (uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SMUAD (uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("smuad %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SMUADX (uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SMUADX (uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("smuadx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SMLAD (uint32_t op1, uint32_t op2, uint32_t op3) +__STATIC_FORCEINLINE uint32_t __SMLAD (uint32_t op1, uint32_t op2, uint32_t op3) { uint32_t result; + __ASM volatile ("smlad %0, %1, %2, %3" : "=r" (result) : "r" (op1), "r" (op2), "r" (op3) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SMLADX (uint32_t op1, uint32_t op2, uint32_t op3) +__STATIC_FORCEINLINE uint32_t __SMLADX (uint32_t op1, uint32_t op2, uint32_t op3) { uint32_t result; + __ASM volatile ("smladx %0, %1, %2, %3" : "=r" (result) : "r" (op1), "r" (op2), "r" (op3) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint64_t __SMLALD (uint32_t op1, uint32_t op2, uint64_t acc) +__STATIC_FORCEINLINE uint64_t __SMLALD (uint32_t op1, uint32_t op2, uint64_t acc) { union llreg_u { @@ -1572,15 +1722,17 @@ __attribute__((always_inline)) __STATIC_INLINE uint64_t __SMLALD (uint32_t op1, uint64_t w64; } llr; llr.w64 = acc; + #ifndef __ARMEB__ /* Little endian */ __ASM volatile ("smlald %0, %1, %2, %3" : "=r" (llr.w32[0]), "=r" (llr.w32[1]): "r" (op1), "r" (op2), "0" (llr.w32[0]), "1" (llr.w32[1]) ); #else /* Big endian */ __ASM volatile ("smlald %0, %1, %2, %3" : "=r" (llr.w32[1]), "=r" (llr.w32[0]): "r" (op1), "r" (op2), "0" (llr.w32[1]), "1" (llr.w32[0]) ); #endif + return (llr.w64); } -__attribute__((always_inline)) __STATIC_INLINE uint64_t __SMLALDX (uint32_t op1, uint32_t op2, uint64_t acc) +__STATIC_FORCEINLINE uint64_t __SMLALDX (uint32_t op1, uint32_t op2, uint64_t acc) { union llreg_u { @@ -1588,43 +1740,49 @@ __attribute__((always_inline)) __STATIC_INLINE uint64_t __SMLALDX (uint32_t op1, uint64_t w64; } llr; llr.w64 = acc; + #ifndef __ARMEB__ /* Little endian */ __ASM volatile ("smlaldx %0, %1, %2, %3" : "=r" (llr.w32[0]), "=r" (llr.w32[1]): "r" (op1), "r" (op2), "0" (llr.w32[0]), "1" (llr.w32[1]) ); #else /* Big endian */ __ASM volatile ("smlaldx %0, %1, %2, %3" : "=r" (llr.w32[1]), "=r" (llr.w32[0]): "r" (op1), "r" (op2), "0" (llr.w32[1]), "1" (llr.w32[0]) ); #endif + return (llr.w64); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SMUSD (uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SMUSD (uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("smusd %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SMUSDX (uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SMUSDX (uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("smusdx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SMLSD (uint32_t op1, uint32_t op2, uint32_t op3) +__STATIC_FORCEINLINE uint32_t __SMLSD (uint32_t op1, uint32_t op2, uint32_t op3) { uint32_t result; + __ASM volatile ("smlsd %0, %1, %2, %3" : "=r" (result) : "r" (op1), "r" (op2), "r" (op3) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SMLSDX (uint32_t op1, uint32_t op2, uint32_t op3) +__STATIC_FORCEINLINE uint32_t __SMLSDX (uint32_t op1, uint32_t op2, uint32_t op3) { uint32_t result; + __ASM volatile ("smlsdx %0, %1, %2, %3" : "=r" (result) : "r" (op1), "r" (op2), "r" (op3) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE uint64_t __SMLSLD (uint32_t op1, uint32_t op2, uint64_t acc) +__STATIC_FORCEINLINE uint64_t __SMLSLD (uint32_t op1, uint32_t op2, uint64_t acc) { union llreg_u { @@ -1632,15 +1790,17 @@ __attribute__((always_inline)) __STATIC_INLINE uint64_t __SMLSLD (uint32_t op1, uint64_t w64; } llr; llr.w64 = acc; + #ifndef __ARMEB__ /* Little endian */ __ASM volatile ("smlsld %0, %1, %2, %3" : "=r" (llr.w32[0]), "=r" (llr.w32[1]): "r" (op1), "r" (op2), "0" (llr.w32[0]), "1" (llr.w32[1]) ); #else /* Big endian */ __ASM volatile ("smlsld %0, %1, %2, %3" : "=r" (llr.w32[1]), "=r" (llr.w32[0]): "r" (op1), "r" (op2), "0" (llr.w32[1]), "1" (llr.w32[0]) ); #endif + return (llr.w64); } -__attribute__((always_inline)) __STATIC_INLINE uint64_t __SMLSLDX (uint32_t op1, uint32_t op2, uint64_t acc) +__STATIC_FORCEINLINE uint64_t __SMLSLDX (uint32_t op1, uint32_t op2, uint64_t acc) { union llreg_u { @@ -1648,35 +1808,41 @@ __attribute__((always_inline)) __STATIC_INLINE uint64_t __SMLSLDX (uint32_t op1, uint64_t w64; } llr; llr.w64 = acc; + #ifndef __ARMEB__ /* Little endian */ __ASM volatile ("smlsldx %0, %1, %2, %3" : "=r" (llr.w32[0]), "=r" (llr.w32[1]): "r" (op1), "r" (op2), "0" (llr.w32[0]), "1" (llr.w32[1]) ); #else /* Big endian */ __ASM volatile ("smlsldx %0, %1, %2, %3" : "=r" (llr.w32[1]), "=r" (llr.w32[0]): "r" (op1), "r" (op2), "0" (llr.w32[1]), "1" (llr.w32[0]) ); #endif + return (llr.w64); } -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SEL (uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SEL (uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("sel %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE int32_t __QADD( int32_t op1, int32_t op2) +__STATIC_FORCEINLINE int32_t __QADD( int32_t op1, int32_t op2) { int32_t result; + __ASM volatile ("qadd %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__((always_inline)) __STATIC_INLINE int32_t __QSUB( int32_t op1, int32_t op2) +__STATIC_FORCEINLINE int32_t __QSUB( int32_t op1, int32_t op2) { int32_t result; + __ASM volatile ("qsub %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } +#if 0 #define __PKHBT(ARG1,ARG2,ARG3) \ ({ \ uint32_t __RES, __ARG1 = (ARG1), __ARG2 = (ARG2); \ @@ -1693,16 +1859,24 @@ __attribute__((always_inline)) __STATIC_INLINE int32_t __QSUB( int32_t op1, in __ASM ("pkhtb %0, %1, %2, asr %3" : "=r" (__RES) : "r" (__ARG1), "r" (__ARG2), "I" (ARG3) ); \ __RES; \ }) +#endif + +#define __PKHBT(ARG1,ARG2,ARG3) ( ((((uint32_t)(ARG1)) ) & 0x0000FFFFUL) | \ + ((((uint32_t)(ARG2)) << (ARG3)) & 0xFFFF0000UL) ) -__attribute__((always_inline)) __STATIC_INLINE uint32_t __SMMLA (int32_t op1, int32_t op2, int32_t op3) +#define __PKHTB(ARG1,ARG2,ARG3) ( ((((uint32_t)(ARG1)) ) & 0xFFFF0000UL) | \ + ((((uint32_t)(ARG2)) >> (ARG3)) & 0x0000FFFFUL) ) + +__STATIC_FORCEINLINE int32_t __SMMLA (int32_t op1, int32_t op2, int32_t op3) { int32_t result; + __ASM volatile ("smmla %0, %1, %2, %3" : "=r" (result): "r" (op1), "r" (op2), "r" (op3) ); return (result); } -#endif /* (__ARM_FEATURE_DSP == 1U) */ +#endif /* (__ARM_FEATURE_DSP == 1) */ /*@} end of group CMSIS_SIMD_intrinsics */ -#endif /* __CMSIS_ARMCC_V6_H */ +#endif /* __CMSIS_ARMCLANG_H */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/cmsis_compiler.h b/EpsilonLights/Drivers/CMSIS/Include/cmsis_compiler.h new file mode 100644 index 00000000..91270869 --- /dev/null +++ b/EpsilonLights/Drivers/CMSIS/Include/cmsis_compiler.h @@ -0,0 +1,275 @@ +/**************************************************************************//** + * @file cmsis_compiler.h + * @brief CMSIS compiler generic header file + * @version V5.0.4 + * @date 10. January 2018 + ******************************************************************************/ +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ + +#ifndef __CMSIS_COMPILER_H +#define __CMSIS_COMPILER_H + +#include + +/* + * Arm Compiler 4/5 + */ +#if defined ( __CC_ARM ) +#include "cmsis_armcc.h" + + +/* + * Arm Compiler 6 (armclang) + */ +#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#include "cmsis_armclang.h" + + +/* + * GNU Compiler + */ +#elif defined ( __GNUC__ ) +#include "cmsis_gcc.h" + + +/* + * IAR Compiler + */ +#elif defined ( __ICCARM__ ) +#include + + +/* + * TI Arm Compiler + */ +#elif defined ( __TI_ARM__ ) +#include + +#ifndef __ASM +#define __ASM __asm +#endif +#ifndef __INLINE +#define __INLINE inline +#endif +#ifndef __STATIC_INLINE +#define __STATIC_INLINE static inline +#endif +#ifndef __STATIC_FORCEINLINE +#define __STATIC_FORCEINLINE __STATIC_INLINE +#endif +#ifndef __NO_RETURN +#define __NO_RETURN __attribute__((noreturn)) +#endif +#ifndef __USED +#define __USED __attribute__((used)) +#endif +#ifndef __WEAK +#define __WEAK __attribute__((weak)) +#endif +#ifndef __PACKED +#define __PACKED __attribute__((packed)) +#endif +#ifndef __PACKED_STRUCT +#define __PACKED_STRUCT struct __attribute__((packed)) +#endif +#ifndef __PACKED_UNION +#define __PACKED_UNION union __attribute__((packed)) +#endif +#ifndef __UNALIGNED_UINT32 /* deprecated */ +struct __attribute__((packed)) T_UINT32 +{ + uint32_t v; +}; +#define __UNALIGNED_UINT32(x) (((struct T_UINT32 *)(x))->v) +#endif +#ifndef __UNALIGNED_UINT16_WRITE +__PACKED_STRUCT T_UINT16_WRITE { uint16_t v; }; +#define __UNALIGNED_UINT16_WRITE(addr, val) (void)((((struct T_UINT16_WRITE *)(void*)(addr))->v) = (val)) +#endif +#ifndef __UNALIGNED_UINT16_READ +__PACKED_STRUCT T_UINT16_READ { uint16_t v; }; +#define __UNALIGNED_UINT16_READ(addr) (((const struct T_UINT16_READ *)(const void *)(addr))->v) +#endif +#ifndef __UNALIGNED_UINT32_WRITE +__PACKED_STRUCT T_UINT32_WRITE { uint32_t v; }; +#define __UNALIGNED_UINT32_WRITE(addr, val) (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val)) +#endif +#ifndef __UNALIGNED_UINT32_READ +__PACKED_STRUCT T_UINT32_READ { uint32_t v; }; +#define __UNALIGNED_UINT32_READ(addr) (((const struct T_UINT32_READ *)(const void *)(addr))->v) +#endif +#ifndef __ALIGNED +#define __ALIGNED(x) __attribute__((aligned(x))) +#endif +#ifndef __RESTRICT +#warning No compiler specific solution for __RESTRICT. __RESTRICT is ignored. +#define __RESTRICT +#endif + + +/* + * TASKING Compiler + */ +#elif defined ( __TASKING__ ) +/* + * The CMSIS functions have been implemented as intrinsics in the compiler. + * Please use "carm -?i" to get an up to date list of all intrinsics, + * Including the CMSIS ones. + */ + +#ifndef __ASM +#define __ASM __asm +#endif +#ifndef __INLINE +#define __INLINE inline +#endif +#ifndef __STATIC_INLINE +#define __STATIC_INLINE static inline +#endif +#ifndef __STATIC_FORCEINLINE +#define __STATIC_FORCEINLINE __STATIC_INLINE +#endif +#ifndef __NO_RETURN +#define __NO_RETURN __attribute__((noreturn)) +#endif +#ifndef __USED +#define __USED __attribute__((used)) +#endif +#ifndef __WEAK +#define __WEAK __attribute__((weak)) +#endif +#ifndef __PACKED +#define __PACKED __packed__ +#endif +#ifndef __PACKED_STRUCT +#define __PACKED_STRUCT struct __packed__ +#endif +#ifndef __PACKED_UNION +#define __PACKED_UNION union __packed__ +#endif +#ifndef __UNALIGNED_UINT32 /* deprecated */ +struct __packed__ T_UINT32 +{ + uint32_t v; +}; +#define __UNALIGNED_UINT32(x) (((struct T_UINT32 *)(x))->v) +#endif +#ifndef __UNALIGNED_UINT16_WRITE +__PACKED_STRUCT T_UINT16_WRITE { uint16_t v; }; +#define __UNALIGNED_UINT16_WRITE(addr, val) (void)((((struct T_UINT16_WRITE *)(void *)(addr))->v) = (val)) +#endif +#ifndef __UNALIGNED_UINT16_READ +__PACKED_STRUCT T_UINT16_READ { uint16_t v; }; +#define __UNALIGNED_UINT16_READ(addr) (((const struct T_UINT16_READ *)(const void *)(addr))->v) +#endif +#ifndef __UNALIGNED_UINT32_WRITE +__PACKED_STRUCT T_UINT32_WRITE { uint32_t v; }; +#define __UNALIGNED_UINT32_WRITE(addr, val) (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val)) +#endif +#ifndef __UNALIGNED_UINT32_READ +__PACKED_STRUCT T_UINT32_READ { uint32_t v; }; +#define __UNALIGNED_UINT32_READ(addr) (((const struct T_UINT32_READ *)(const void *)(addr))->v) +#endif +#ifndef __ALIGNED +#define __ALIGNED(x) __align(x) +#endif +#ifndef __RESTRICT +#warning No compiler specific solution for __RESTRICT. __RESTRICT is ignored. +#define __RESTRICT +#endif + + +/* + * COSMIC Compiler + */ +#elif defined ( __CSMC__ ) +#include + +#ifndef __ASM +#define __ASM _asm +#endif +#ifndef __INLINE +#define __INLINE inline +#endif +#ifndef __STATIC_INLINE +#define __STATIC_INLINE static inline +#endif +#ifndef __STATIC_FORCEINLINE +#define __STATIC_FORCEINLINE __STATIC_INLINE +#endif +#ifndef __NO_RETURN +// NO RETURN is automatically detected hence no warning here +#define __NO_RETURN +#endif +#ifndef __USED +#warning No compiler specific solution for __USED. __USED is ignored. +#define __USED +#endif +#ifndef __WEAK +#define __WEAK __weak +#endif +#ifndef __PACKED +#define __PACKED @packed +#endif +#ifndef __PACKED_STRUCT +#define __PACKED_STRUCT @packed struct +#endif +#ifndef __PACKED_UNION +#define __PACKED_UNION @packed union +#endif +#ifndef __UNALIGNED_UINT32 /* deprecated */ +@packed struct T_UINT32 +{ + uint32_t v; +}; +#define __UNALIGNED_UINT32(x) (((struct T_UINT32 *)(x))->v) +#endif +#ifndef __UNALIGNED_UINT16_WRITE +__PACKED_STRUCT T_UINT16_WRITE { uint16_t v; }; +#define __UNALIGNED_UINT16_WRITE(addr, val) (void)((((struct T_UINT16_WRITE *)(void *)(addr))->v) = (val)) +#endif +#ifndef __UNALIGNED_UINT16_READ +__PACKED_STRUCT T_UINT16_READ { uint16_t v; }; +#define __UNALIGNED_UINT16_READ(addr) (((const struct T_UINT16_READ *)(const void *)(addr))->v) +#endif +#ifndef __UNALIGNED_UINT32_WRITE +__PACKED_STRUCT T_UINT32_WRITE { uint32_t v; }; +#define __UNALIGNED_UINT32_WRITE(addr, val) (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val)) +#endif +#ifndef __UNALIGNED_UINT32_READ +__PACKED_STRUCT T_UINT32_READ { uint32_t v; }; +#define __UNALIGNED_UINT32_READ(addr) (((const struct T_UINT32_READ *)(const void *)(addr))->v) +#endif +#ifndef __ALIGNED +#warning No compiler specific solution for __ALIGNED. __ALIGNED is ignored. +#define __ALIGNED(x) +#endif +#ifndef __RESTRICT +#warning No compiler specific solution for __RESTRICT. __RESTRICT is ignored. +#define __RESTRICT +#endif + + +#else +#error Unknown compiler. +#endif + + +#endif /* __CMSIS_COMPILER_H */ + diff --git a/EpsilonLights/Drivers/CMSIS/Include/cmsis_gcc.h b/EpsilonLights/Drivers/CMSIS/Include/cmsis_gcc.h index 5182cf10..ae763e5c 100644 --- a/EpsilonLights/Drivers/CMSIS/Include/cmsis_gcc.h +++ b/EpsilonLights/Drivers/CMSIS/Include/cmsis_gcc.h @@ -1,46 +1,120 @@ /**************************************************************************//** * @file cmsis_gcc.h - * @brief CMSIS Cortex-M Core Function/Instruction Header File - * @version V4.30 - * @date 20. October 2015 + * @brief CMSIS compiler GCC header file + * @version V5.0.4 + * @date 09. April 2018 ******************************************************************************/ -/* Copyright (c) 2009 - 2015 ARM LIMITED - - All rights reserved. - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - - Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - - Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - Neither the name of ARM nor the names of its contributors may be used - to endorse or promote products derived from this software without - specific prior written permission. - * - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE - LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR - CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF - SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS - INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN - CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) - ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE - POSSIBILITY OF SUCH DAMAGE. - ---------------------------------------------------------------------------*/ - +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ #ifndef __CMSIS_GCC_H #define __CMSIS_GCC_H /* ignore some GCC warnings */ -#if defined ( __GNUC__ ) #pragma GCC diagnostic push #pragma GCC diagnostic ignored "-Wsign-conversion" #pragma GCC diagnostic ignored "-Wconversion" #pragma GCC diagnostic ignored "-Wunused-parameter" + +/* Fallback for __has_builtin */ +#ifndef __has_builtin +#define __has_builtin(x) (0) +#endif + +/* CMSIS compiler specific defines */ +#ifndef __ASM +#define __ASM __asm +#endif +#ifndef __INLINE +#define __INLINE inline +#endif +#ifndef __STATIC_INLINE +#define __STATIC_INLINE static inline +#endif +#ifndef __STATIC_FORCEINLINE +#define __STATIC_FORCEINLINE __attribute__((always_inline)) static inline +#endif +#ifndef __NO_RETURN +#define __NO_RETURN __attribute__((__noreturn__)) +#endif +#ifndef __USED +#define __USED __attribute__((used)) +#endif +#ifndef __WEAK +#define __WEAK __attribute__((weak)) +#endif +#ifndef __PACKED +#define __PACKED __attribute__((packed, aligned(1))) +#endif +#ifndef __PACKED_STRUCT +#define __PACKED_STRUCT struct __attribute__((packed, aligned(1))) +#endif +#ifndef __PACKED_UNION +#define __PACKED_UNION union __attribute__((packed, aligned(1))) +#endif +#ifndef __UNALIGNED_UINT32 /* deprecated */ +#pragma GCC diagnostic push +#pragma GCC diagnostic ignored "-Wpacked" +#pragma GCC diagnostic ignored "-Wattributes" +struct __attribute__((packed)) T_UINT32 +{ + uint32_t v; +}; +#pragma GCC diagnostic pop +#define __UNALIGNED_UINT32(x) (((struct T_UINT32 *)(x))->v) +#endif +#ifndef __UNALIGNED_UINT16_WRITE +#pragma GCC diagnostic push +#pragma GCC diagnostic ignored "-Wpacked" +#pragma GCC diagnostic ignored "-Wattributes" +__PACKED_STRUCT T_UINT16_WRITE { uint16_t v; }; +#pragma GCC diagnostic pop +#define __UNALIGNED_UINT16_WRITE(addr, val) (void)((((struct T_UINT16_WRITE *)(void *)(addr))->v) = (val)) +#endif +#ifndef __UNALIGNED_UINT16_READ +#pragma GCC diagnostic push +#pragma GCC diagnostic ignored "-Wpacked" +#pragma GCC diagnostic ignored "-Wattributes" +__PACKED_STRUCT T_UINT16_READ { uint16_t v; }; +#pragma GCC diagnostic pop +#define __UNALIGNED_UINT16_READ(addr) (((const struct T_UINT16_READ *)(const void *)(addr))->v) +#endif +#ifndef __UNALIGNED_UINT32_WRITE +#pragma GCC diagnostic push +#pragma GCC diagnostic ignored "-Wpacked" +#pragma GCC diagnostic ignored "-Wattributes" +__PACKED_STRUCT T_UINT32_WRITE { uint32_t v; }; +#pragma GCC diagnostic pop +#define __UNALIGNED_UINT32_WRITE(addr, val) (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val)) +#endif +#ifndef __UNALIGNED_UINT32_READ +#pragma GCC diagnostic push +#pragma GCC diagnostic ignored "-Wpacked" +#pragma GCC diagnostic ignored "-Wattributes" +__PACKED_STRUCT T_UINT32_READ { uint32_t v; }; +#pragma GCC diagnostic pop +#define __UNALIGNED_UINT32_READ(addr) (((const struct T_UINT32_READ *)(const void *)(addr))->v) +#endif +#ifndef __ALIGNED +#define __ALIGNED(x) __attribute__((aligned(x))) +#endif +#ifndef __RESTRICT +#define __RESTRICT __restrict #endif @@ -55,7 +129,7 @@ \details Enables IRQ interrupts by clearing the I-bit in the CPSR. Can only be executed in Privileged modes. */ -__attribute__( ( always_inline ) ) __STATIC_INLINE void __enable_irq(void) +__STATIC_FORCEINLINE void __enable_irq(void) { __ASM volatile ("cpsie i" : : : "memory"); } @@ -64,9 +138,9 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE void __enable_irq(void) /** \brief Disable IRQ Interrupts \details Disables IRQ interrupts by setting the I-bit in the CPSR. - Can only be executed in Privileged modes. + Can only be executed in Privileged modes. */ -__attribute__( ( always_inline ) ) __STATIC_INLINE void __disable_irq(void) +__STATIC_FORCEINLINE void __disable_irq(void) { __ASM volatile ("cpsid i" : : : "memory"); } @@ -77,33 +151,64 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE void __disable_irq(void) \details Returns the content of the Control Register. \return Control Register value */ -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __get_CONTROL(void) +__STATIC_FORCEINLINE uint32_t __get_CONTROL(void) { uint32_t result; + __ASM volatile ("MRS %0, control" : "=r" (result) ); return (result); } +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Get Control Register (non-secure) + \details Returns the content of the non-secure Control Register when in secure mode. + \return non-secure Control Register value + */ +__STATIC_FORCEINLINE uint32_t __TZ_get_CONTROL_NS(void) +{ + uint32_t result; + + __ASM volatile ("MRS %0, control_ns" : "=r" (result) ); + return (result); +} +#endif + + /** \brief Set Control Register \details Writes the given value to the Control Register. \param [in] control Control Register value to set */ -__attribute__( ( always_inline ) ) __STATIC_INLINE void __set_CONTROL(uint32_t control) +__STATIC_FORCEINLINE void __set_CONTROL(uint32_t control) { __ASM volatile ("MSR control, %0" : : "r" (control) : "memory"); } +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Set Control Register (non-secure) + \details Writes the given value to the non-secure Control Register when in secure state. + \param [in] control Control Register value to set + */ +__STATIC_FORCEINLINE void __TZ_set_CONTROL_NS(uint32_t control) +{ + __ASM volatile ("MSR control_ns, %0" : : "r" (control) : "memory"); +} +#endif + + /** \brief Get IPSR Register \details Returns the content of the IPSR Register. \return IPSR Register value */ -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __get_IPSR(void) +__STATIC_FORCEINLINE uint32_t __get_IPSR(void) { uint32_t result; + __ASM volatile ("MRS %0, ipsr" : "=r" (result) ); return (result); } @@ -114,9 +219,10 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __get_IPSR(void) \details Returns the content of the APSR Register. \return APSR Register value */ -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __get_APSR(void) +__STATIC_FORCEINLINE uint32_t __get_APSR(void) { uint32_t result; + __ASM volatile ("MRS %0, apsr" : "=r" (result) ); return (result); } @@ -125,12 +231,12 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __get_APSR(void) /** \brief Get xPSR Register \details Returns the content of the xPSR Register. - - \return xPSR Register value + \return xPSR Register value */ -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __get_xPSR(void) +__STATIC_FORCEINLINE uint32_t __get_xPSR(void) { uint32_t result; + __ASM volatile ("MRS %0, xpsr" : "=r" (result) ); return (result); } @@ -141,48 +247,134 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __get_xPSR(void) \details Returns the current value of the Process Stack Pointer (PSP). \return PSP Register value */ -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __get_PSP(void) +__STATIC_FORCEINLINE uint32_t __get_PSP(void) { - register uint32_t result; - __ASM volatile ("MRS %0, psp\n" : "=r" (result) ); + uint32_t result; + + __ASM volatile ("MRS %0, psp" : "=r" (result) ); return (result); } +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Get Process Stack Pointer (non-secure) + \details Returns the current value of the non-secure Process Stack Pointer (PSP) when in secure state. + \return PSP Register value + */ +__STATIC_FORCEINLINE uint32_t __TZ_get_PSP_NS(void) +{ + uint32_t result; + + __ASM volatile ("MRS %0, psp_ns" : "=r" (result) ); + return (result); +} +#endif + + /** \brief Set Process Stack Pointer \details Assigns the given value to the Process Stack Pointer (PSP). \param [in] topOfProcStack Process Stack Pointer value to set */ -__attribute__( ( always_inline ) ) __STATIC_INLINE void __set_PSP(uint32_t topOfProcStack) +__STATIC_FORCEINLINE void __set_PSP(uint32_t topOfProcStack) { - __ASM volatile ("MSR psp, %0\n" : : "r" (topOfProcStack) : "sp"); + __ASM volatile ("MSR psp, %0" : : "r" (topOfProcStack) : ); } +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Set Process Stack Pointer (non-secure) + \details Assigns the given value to the non-secure Process Stack Pointer (PSP) when in secure state. + \param [in] topOfProcStack Process Stack Pointer value to set + */ +__STATIC_FORCEINLINE void __TZ_set_PSP_NS(uint32_t topOfProcStack) +{ + __ASM volatile ("MSR psp_ns, %0" : : "r" (topOfProcStack) : ); +} +#endif + + /** \brief Get Main Stack Pointer \details Returns the current value of the Main Stack Pointer (MSP). \return MSP Register value */ -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __get_MSP(void) +__STATIC_FORCEINLINE uint32_t __get_MSP(void) +{ + uint32_t result; + + __ASM volatile ("MRS %0, msp" : "=r" (result) ); + return (result); +} + + +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Get Main Stack Pointer (non-secure) + \details Returns the current value of the non-secure Main Stack Pointer (MSP) when in secure state. + \return MSP Register value + */ +__STATIC_FORCEINLINE uint32_t __TZ_get_MSP_NS(void) { - register uint32_t result; - __ASM volatile ("MRS %0, msp\n" : "=r" (result) ); + uint32_t result; + + __ASM volatile ("MRS %0, msp_ns" : "=r" (result) ); return (result); } +#endif /** \brief Set Main Stack Pointer \details Assigns the given value to the Main Stack Pointer (MSP). + \param [in] topOfMainStack Main Stack Pointer value to set + */ +__STATIC_FORCEINLINE void __set_MSP(uint32_t topOfMainStack) +{ + __ASM volatile ("MSR msp, %0" : : "r" (topOfMainStack) : ); +} + - \param [in] topOfMainStack Main Stack Pointer value to set +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Set Main Stack Pointer (non-secure) + \details Assigns the given value to the non-secure Main Stack Pointer (MSP) when in secure state. + \param [in] topOfMainStack Main Stack Pointer value to set */ -__attribute__( ( always_inline ) ) __STATIC_INLINE void __set_MSP(uint32_t topOfMainStack) +__STATIC_FORCEINLINE void __TZ_set_MSP_NS(uint32_t topOfMainStack) { - __ASM volatile ("MSR msp, %0\n" : : "r" (topOfMainStack) : "sp"); + __ASM volatile ("MSR msp_ns, %0" : : "r" (topOfMainStack) : ); } +#endif + + +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Get Stack Pointer (non-secure) + \details Returns the current value of the non-secure Stack Pointer (SP) when in secure state. + \return SP Register value + */ +__STATIC_FORCEINLINE uint32_t __TZ_get_SP_NS(void) +{ + uint32_t result; + + __ASM volatile ("MRS %0, sp_ns" : "=r" (result) ); + return (result); +} + + +/** + \brief Set Stack Pointer (non-secure) + \details Assigns the given value to the non-secure Stack Pointer (SP) when in secure state. + \param [in] topOfStack Stack Pointer value to set + */ +__STATIC_FORCEINLINE void __TZ_set_SP_NS(uint32_t topOfStack) +{ + __ASM volatile ("MSR sp_ns, %0" : : "r" (topOfStack) : ); +} +#endif /** @@ -190,33 +382,64 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE void __set_MSP(uint32_t topOf \details Returns the current state of the priority mask bit from the Priority Mask Register. \return Priority Mask value */ -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __get_PRIMASK(void) +__STATIC_FORCEINLINE uint32_t __get_PRIMASK(void) { uint32_t result; - __ASM volatile ("MRS %0, primask" : "=r" (result) ); + + __ASM volatile ("MRS %0, primask" : "=r" (result) :: "memory"); return (result); } +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Get Priority Mask (non-secure) + \details Returns the current state of the non-secure priority mask bit from the Priority Mask Register when in secure state. + \return Priority Mask value + */ +__STATIC_FORCEINLINE uint32_t __TZ_get_PRIMASK_NS(void) +{ + uint32_t result; + + __ASM volatile ("MRS %0, primask_ns" : "=r" (result) :: "memory"); + return (result); +} +#endif + + /** \brief Set Priority Mask \details Assigns the given value to the Priority Mask Register. \param [in] priMask Priority Mask */ -__attribute__( ( always_inline ) ) __STATIC_INLINE void __set_PRIMASK(uint32_t priMask) +__STATIC_FORCEINLINE void __set_PRIMASK(uint32_t priMask) { __ASM volatile ("MSR primask, %0" : : "r" (priMask) : "memory"); } -#if (__CORTEX_M >= 0x03U) +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Set Priority Mask (non-secure) + \details Assigns the given value to the non-secure Priority Mask Register when in secure state. + \param [in] priMask Priority Mask + */ +__STATIC_FORCEINLINE void __TZ_set_PRIMASK_NS(uint32_t priMask) +{ + __ASM volatile ("MSR primask_ns, %0" : : "r" (priMask) : "memory"); +} +#endif + +#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__ ) && (__ARM_ARCH_7EM__ == 1)) || \ + (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) ) /** \brief Enable FIQ \details Enables FIQ interrupts by clearing the F-bit in the CPSR. Can only be executed in Privileged modes. */ -__attribute__( ( always_inline ) ) __STATIC_INLINE void __enable_fault_irq(void) +__STATIC_FORCEINLINE void __enable_fault_irq(void) { __ASM volatile ("cpsie f" : : : "memory"); } @@ -227,7 +450,7 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE void __enable_fault_irq(void) \details Disables FIQ interrupts by setting the F-bit in the CPSR. Can only be executed in Privileged modes. */ -__attribute__( ( always_inline ) ) __STATIC_INLINE void __disable_fault_irq(void) +__STATIC_FORCEINLINE void __disable_fault_irq(void) { __ASM volatile ("cpsid f" : : : "memory"); } @@ -238,34 +461,64 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE void __disable_fault_irq(void \details Returns the current value of the Base Priority register. \return Base Priority register value */ -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __get_BASEPRI(void) +__STATIC_FORCEINLINE uint32_t __get_BASEPRI(void) { uint32_t result; + __ASM volatile ("MRS %0, basepri" : "=r" (result) ); return (result); } +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Get Base Priority (non-secure) + \details Returns the current value of the non-secure Base Priority register when in secure state. + \return Base Priority register value + */ +__STATIC_FORCEINLINE uint32_t __TZ_get_BASEPRI_NS(void) +{ + uint32_t result; + + __ASM volatile ("MRS %0, basepri_ns" : "=r" (result) ); + return (result); +} +#endif + + /** \brief Set Base Priority \details Assigns the given value to the Base Priority register. \param [in] basePri Base Priority value to set */ -__attribute__( ( always_inline ) ) __STATIC_INLINE void __set_BASEPRI(uint32_t value) +__STATIC_FORCEINLINE void __set_BASEPRI(uint32_t basePri) { - __ASM volatile ("MSR basepri, %0" : : "r" (value) : "memory"); + __ASM volatile ("MSR basepri, %0" : : "r" (basePri) : "memory"); } +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Set Base Priority (non-secure) + \details Assigns the given value to the non-secure Base Priority register when in secure state. + \param [in] basePri Base Priority value to set + */ +__STATIC_FORCEINLINE void __TZ_set_BASEPRI_NS(uint32_t basePri) +{ + __ASM volatile ("MSR basepri_ns, %0" : : "r" (basePri) : "memory"); +} +#endif + + /** \brief Set Base Priority with condition \details Assigns the given value to the Base Priority register only if BASEPRI masking is disabled, or the new value increases the BASEPRI priority level. \param [in] basePri Base Priority value to set */ -__attribute__( ( always_inline ) ) __STATIC_INLINE void __set_BASEPRI_MAX(uint32_t value) +__STATIC_FORCEINLINE void __set_BASEPRI_MAX(uint32_t basePri) { - __ASM volatile ("MSR basepri_max, %0" : : "r" (value) : "memory"); + __ASM volatile ("MSR basepri_max, %0" : : "r" (basePri) : "memory"); } @@ -274,45 +527,262 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE void __set_BASEPRI_MAX(uint32 \details Returns the current value of the Fault Mask register. \return Fault Mask register value */ -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __get_FAULTMASK(void) +__STATIC_FORCEINLINE uint32_t __get_FAULTMASK(void) { uint32_t result; + __ASM volatile ("MRS %0, faultmask" : "=r" (result) ); return (result); } +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Get Fault Mask (non-secure) + \details Returns the current value of the non-secure Fault Mask register when in secure state. + \return Fault Mask register value + */ +__STATIC_FORCEINLINE uint32_t __TZ_get_FAULTMASK_NS(void) +{ + uint32_t result; + + __ASM volatile ("MRS %0, faultmask_ns" : "=r" (result) ); + return (result); +} +#endif + + /** \brief Set Fault Mask \details Assigns the given value to the Fault Mask register. \param [in] faultMask Fault Mask value to set */ -__attribute__( ( always_inline ) ) __STATIC_INLINE void __set_FAULTMASK(uint32_t faultMask) +__STATIC_FORCEINLINE void __set_FAULTMASK(uint32_t faultMask) { __ASM volatile ("MSR faultmask, %0" : : "r" (faultMask) : "memory"); } -#endif /* (__CORTEX_M >= 0x03U) */ +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Set Fault Mask (non-secure) + \details Assigns the given value to the non-secure Fault Mask register when in secure state. + \param [in] faultMask Fault Mask value to set + */ +__STATIC_FORCEINLINE void __TZ_set_FAULTMASK_NS(uint32_t faultMask) +{ + __ASM volatile ("MSR faultmask_ns, %0" : : "r" (faultMask) : "memory"); +} +#endif + +#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__ ) && (__ARM_ARCH_7EM__ == 1)) || \ + (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) ) */ + + +#if ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \ + (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1)) ) + +/** + \brief Get Process Stack Pointer Limit + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence zero is returned always in non-secure + mode. + + \details Returns the current value of the Process Stack Pointer Limit (PSPLIM). + \return PSPLIM Register value + */ +__STATIC_FORCEINLINE uint32_t __get_PSPLIM(void) +{ +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3))) + // without main extensions, the non-secure PSPLIM is RAZ/WI + return 0U; +#else + uint32_t result; + __ASM volatile ("MRS %0, psplim" : "=r" (result) ); + return result; +#endif +} + +#if (defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Get Process Stack Pointer Limit (non-secure) + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence zero is returned always. + + \details Returns the current value of the non-secure Process Stack Pointer Limit (PSPLIM) when in secure state. + \return PSPLIM Register value + */ +__STATIC_FORCEINLINE uint32_t __TZ_get_PSPLIM_NS(void) +{ +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1))) + // without main extensions, the non-secure PSPLIM is RAZ/WI + return 0U; +#else + uint32_t result; + __ASM volatile ("MRS %0, psplim_ns" : "=r" (result) ); + return result; +#endif +} +#endif + + +/** + \brief Set Process Stack Pointer Limit + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence the write is silently ignored in non-secure + mode. + + \details Assigns the given value to the Process Stack Pointer Limit (PSPLIM). + \param [in] ProcStackPtrLimit Process Stack Pointer Limit value to set + */ +__STATIC_FORCEINLINE void __set_PSPLIM(uint32_t ProcStackPtrLimit) +{ +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3))) + // without main extensions, the non-secure PSPLIM is RAZ/WI + (void)ProcStackPtrLimit; +#else + __ASM volatile ("MSR psplim, %0" : : "r" (ProcStackPtrLimit)); +#endif +} + + +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Set Process Stack Pointer (non-secure) + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence the write is silently ignored. + + \details Assigns the given value to the non-secure Process Stack Pointer Limit (PSPLIM) when in secure state. + \param [in] ProcStackPtrLimit Process Stack Pointer Limit value to set + */ +__STATIC_FORCEINLINE void __TZ_set_PSPLIM_NS(uint32_t ProcStackPtrLimit) +{ +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1))) + // without main extensions, the non-secure PSPLIM is RAZ/WI + (void)ProcStackPtrLimit; +#else + __ASM volatile ("MSR psplim_ns, %0\n" : : "r" (ProcStackPtrLimit)); +#endif +} +#endif + + +/** + \brief Get Main Stack Pointer Limit + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence zero is returned always in non-secure + mode. + + \details Returns the current value of the Main Stack Pointer Limit (MSPLIM). + \return MSPLIM Register value + */ +__STATIC_FORCEINLINE uint32_t __get_MSPLIM(void) +{ +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3))) + // without main extensions, the non-secure MSPLIM is RAZ/WI + return 0U; +#else + uint32_t result; + __ASM volatile ("MRS %0, msplim" : "=r" (result) ); + return result; +#endif +} + + +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Get Main Stack Pointer Limit (non-secure) + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence zero is returned always. + + \details Returns the current value of the non-secure Main Stack Pointer Limit(MSPLIM) when in secure state. + \return MSPLIM Register value + */ +__STATIC_FORCEINLINE uint32_t __TZ_get_MSPLIM_NS(void) +{ +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1))) + // without main extensions, the non-secure MSPLIM is RAZ/WI + return 0U; +#else + uint32_t result; + __ASM volatile ("MRS %0, msplim_ns" : "=r" (result) ); + return result; +#endif +} +#endif + + +/** + \brief Set Main Stack Pointer Limit + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence the write is silently ignored in non-secure + mode. + + \details Assigns the given value to the Main Stack Pointer Limit (MSPLIM). + \param [in] MainStackPtrLimit Main Stack Pointer Limit value to set + */ +__STATIC_FORCEINLINE void __set_MSPLIM(uint32_t MainStackPtrLimit) +{ +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3))) + // without main extensions, the non-secure MSPLIM is RAZ/WI + (void)MainStackPtrLimit; +#else + __ASM volatile ("MSR msplim, %0" : : "r" (MainStackPtrLimit)); +#endif +} + + +#if (defined (__ARM_FEATURE_CMSE ) && (__ARM_FEATURE_CMSE == 3)) +/** + \brief Set Main Stack Pointer Limit (non-secure) + Devices without ARMv8-M Main Extensions (i.e. Cortex-M23) lack the non-secure + Stack Pointer Limit register hence the write is silently ignored. + + \details Assigns the given value to the non-secure Main Stack Pointer Limit (MSPLIM) when in secure state. + \param [in] MainStackPtrLimit Main Stack Pointer value to set + */ +__STATIC_FORCEINLINE void __TZ_set_MSPLIM_NS(uint32_t MainStackPtrLimit) +{ +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1))) + // without main extensions, the non-secure MSPLIM is RAZ/WI + (void)MainStackPtrLimit; +#else + __ASM volatile ("MSR msplim_ns, %0" : : "r" (MainStackPtrLimit)); +#endif +} +#endif + +#endif /* ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \ + (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1)) ) */ -#if (__CORTEX_M == 0x04U) || (__CORTEX_M == 0x07U) /** \brief Get FPSCR \details Returns the current value of the Floating Point Status/Control register. \return Floating Point Status/Control register value */ -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __get_FPSCR(void) -{ -#if (__FPU_PRESENT == 1U) && (__FPU_USED == 1U) +__STATIC_FORCEINLINE uint32_t __get_FPSCR(void) +{ +#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \ + (defined (__FPU_USED ) && (__FPU_USED == 1U)) ) +#if __has_builtin(__builtin_arm_get_fpscr) +// Re-enable using built-in when GCC has been fixed +// || (__GNUC__ > 7) || (__GNUC__ == 7 && __GNUC_MINOR__ >= 2) + /* see https://gcc.gnu.org/ml/gcc-patches/2017-04/msg00443.html */ + return __builtin_arm_get_fpscr(); +#else uint32_t result; - /* Empty asm statement works as a scheduling barrier */ - __ASM volatile (""); + __ASM volatile ("VMRS %0, fpscr" : "=r" (result) ); - __ASM volatile (""); return (result); +#endif #else - return (0); + return (0U); #endif } @@ -322,19 +792,23 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __get_FPSCR(void) \details Assigns the given value to the Floating Point Status/Control register. \param [in] fpscr Floating Point Status/Control value to set */ -__attribute__( ( always_inline ) ) __STATIC_INLINE void __set_FPSCR(uint32_t fpscr) -{ -#if (__FPU_PRESENT == 1U) && (__FPU_USED == 1U) - /* Empty asm statement works as a scheduling barrier */ - __ASM volatile (""); - __ASM volatile ("VMSR fpscr, %0" : : "r" (fpscr) : "vfpcc"); - __ASM volatile (""); +__STATIC_FORCEINLINE void __set_FPSCR(uint32_t fpscr) +{ +#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \ + (defined (__FPU_USED ) && (__FPU_USED == 1U)) ) +#if __has_builtin(__builtin_arm_set_fpscr) +// Re-enable using built-in when GCC has been fixed +// || (__GNUC__ > 7) || (__GNUC__ == 7 && __GNUC_MINOR__ >= 2) + /* see https://gcc.gnu.org/ml/gcc-patches/2017-04/msg00443.html */ + __builtin_arm_set_fpscr(fpscr); +#else + __ASM volatile ("VMSR fpscr, %0" : : "r" (fpscr) : "vfpcc", "memory"); +#endif +#else + (void)fpscr; #endif } -#endif /* (__CORTEX_M == 0x04U) || (__CORTEX_M == 0x07U) */ - - /*@} end of CMSIS_Core_RegAccFunctions */ @@ -350,9 +824,11 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE void __set_FPSCR(uint32_t fps * Otherwise, use general registers, specified by constraint "r" */ #if defined (__thumb__) && !defined (__thumb2__) #define __CMSIS_GCC_OUT_REG(r) "=l" (r) +#define __CMSIS_GCC_RW_REG(r) "+l" (r) #define __CMSIS_GCC_USE_REG(r) "l" (r) #else #define __CMSIS_GCC_OUT_REG(r) "=r" (r) +#define __CMSIS_GCC_RW_REG(r) "+r" (r) #define __CMSIS_GCC_USE_REG(r) "r" (r) #endif @@ -360,41 +836,28 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE void __set_FPSCR(uint32_t fps \brief No Operation \details No Operation does nothing. This instruction can be used for code alignment purposes. */ -__attribute__((always_inline)) __STATIC_INLINE void __NOP(void) -{ - __ASM volatile ("nop"); -} - +#define __NOP() __ASM volatile ("nop") /** \brief Wait For Interrupt \details Wait For Interrupt is a hint instruction that suspends execution until one of a number of events occurs. */ -__attribute__((always_inline)) __STATIC_INLINE void __WFI(void) -{ - __ASM volatile ("wfi"); -} +#define __WFI() __ASM volatile ("wfi") /** \brief Wait For Event \details Wait For Event is a hint instruction that permits the processor to enter - a low-power state until one of a number of events occurs. - */ -__attribute__((always_inline)) __STATIC_INLINE void __WFE(void) -{ - __ASM volatile ("wfe"); -} + a low-power state until one of a number of events occurs. + */ +#define __WFE() __ASM volatile ("wfe") /** \brief Send Event \details Send Event is a hint instruction. It causes an event to be signaled to the CPU. */ -__attribute__((always_inline)) __STATIC_INLINE void __SEV(void) -{ - __ASM volatile ("sev"); -} +#define __SEV() __ASM volatile ("sev") /** @@ -403,7 +866,7 @@ __attribute__((always_inline)) __STATIC_INLINE void __SEV(void) so that all instructions following the ISB are fetched from cache or memory, after the instruction has been completed. */ -__attribute__((always_inline)) __STATIC_INLINE void __ISB(void) +__STATIC_FORCEINLINE void __ISB(void) { __ASM volatile ("isb 0xF"::: "memory"); } @@ -414,7 +877,7 @@ __attribute__((always_inline)) __STATIC_INLINE void __ISB(void) \details Acts as a special kind of Data Memory Barrier. It completes when all explicit memory accesses before this instruction complete. */ -__attribute__((always_inline)) __STATIC_INLINE void __DSB(void) +__STATIC_FORCEINLINE void __DSB(void) { __ASM volatile ("dsb 0xF"::: "memory"); } @@ -425,7 +888,7 @@ __attribute__((always_inline)) __STATIC_INLINE void __DSB(void) \details Ensures the apparent order of the explicit memory operations before and after the instruction, without ensuring their completion. */ -__attribute__((always_inline)) __STATIC_INLINE void __DMB(void) +__STATIC_FORCEINLINE void __DMB(void) { __ASM volatile ("dmb 0xF"::: "memory"); } @@ -433,50 +896,53 @@ __attribute__((always_inline)) __STATIC_INLINE void __DMB(void) /** \brief Reverse byte order (32 bit) - \details Reverses the byte order in integer value. + \details Reverses the byte order in unsigned integer value. For example, 0x12345678 becomes 0x78563412. \param [in] value Value to reverse \return Reversed value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __REV(uint32_t value) +__STATIC_FORCEINLINE uint32_t __REV(uint32_t value) { #if (__GNUC__ > 4) || (__GNUC__ == 4 && __GNUC_MINOR__ >= 5) return __builtin_bswap32(value); #else uint32_t result; + __ASM volatile ("rev %0, %1" : __CMSIS_GCC_OUT_REG (result) : __CMSIS_GCC_USE_REG (value) ); - return (result); + return result; #endif } /** \brief Reverse byte order (16 bit) - \details Reverses the byte order in two unsigned short values. + \details Reverses the byte order within each halfword of a word. For example, 0x12345678 becomes 0x34127856. \param [in] value Value to reverse \return Reversed value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __REV16(uint32_t value) +__STATIC_FORCEINLINE uint32_t __REV16(uint32_t value) { uint32_t result; + __ASM volatile ("rev16 %0, %1" : __CMSIS_GCC_OUT_REG (result) : __CMSIS_GCC_USE_REG (value) ); - return (result); + return result; } /** - \brief Reverse byte order in signed short value - \details Reverses the byte order in a signed short value with sign extension to integer. + \brief Reverse byte order (16 bit) + \details Reverses the byte order in a 16-bit value and returns the signed 16-bit result. For example, 0x0080 becomes 0x8000. \param [in] value Value to reverse \return Reversed value */ -__attribute__((always_inline)) __STATIC_INLINE int32_t __REVSH(int32_t value) +__STATIC_FORCEINLINE int16_t __REVSH(int16_t value) { #if (__GNUC__ > 4) || (__GNUC__ == 4 && __GNUC_MINOR__ >= 8) - return (short)__builtin_bswap16(value); + return (int16_t)__builtin_bswap16(value); #else - int32_t result; + int16_t result; + __ASM volatile ("revsh %0, %1" : __CMSIS_GCC_OUT_REG (result) : __CMSIS_GCC_USE_REG (value) ); - return (result); + return result; #endif } @@ -484,12 +950,19 @@ __attribute__((always_inline)) __STATIC_INLINE int32_t __REVSH(int32_t value) /** \brief Rotate Right in unsigned value (32 bit) \details Rotate Right (immediate) provides the value of the contents of a register rotated by a variable number of bits. - \param [in] value Value to rotate - \param [in] value Number of Bits to rotate + \param [in] op1 Value to rotate + \param [in] op2 Number of Bits to rotate \return Rotated value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __ROR(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __ROR(uint32_t op1, uint32_t op2) { + op2 %= 32U; + + if (op2 == 0U) + { + return op1; + } + return (op1 >> op2) | (op1 << (32U - op2)); } @@ -510,16 +983,20 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __ROR(uint32_t op1, uint \param [in] value Value to reverse \return Reversed value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value) +__STATIC_FORCEINLINE uint32_t __RBIT(uint32_t value) { uint32_t result; -#if (__CORTEX_M >= 0x03U) || (__CORTEX_SC >= 300U) + +#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__ ) && (__ARM_ARCH_7EM__ == 1)) || \ + (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) ) __ASM volatile ("rbit %0, %1" : "=r" (result) : "r" (value) ); #else - int32_t s = 4 /*sizeof(v)*/ * 8 - 1; /* extra shift needed at end */ + uint32_t s = (4U /*sizeof(v)*/ * 8U) - 1U; /* extra shift needed at end */ + result = value; /* r will be reversed bits of v; first get LSB of v */ - for (value >>= 1U; value; value >>= 1U) + for (value >>= 1U; value != 0U; value >>= 1U) { result <<= 1U; result |= value & 1U; @@ -528,7 +1005,7 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value) result <<= s; /* shift when v's highest bits are zero */ #endif - return (result); + return result; } @@ -538,20 +1015,23 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value) \param [in] value Value to count the leading zeros \return number of leading zeros in value */ -#define __CLZ __builtin_clz - +#define __CLZ (uint8_t)__builtin_clz -#if (__CORTEX_M >= 0x03U) || (__CORTEX_SC >= 300U) +#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__ ) && (__ARM_ARCH_7EM__ == 1)) || \ + (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \ + (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1)) ) /** \brief LDR Exclusive (8 bit) \details Executes a exclusive LDR instruction for 8 bit value. \param [in] ptr Pointer to data \return value of type uint8_t at (*ptr) */ -__attribute__((always_inline)) __STATIC_INLINE uint8_t __LDREXB(volatile uint8_t* addr) +__STATIC_FORCEINLINE uint8_t __LDREXB(volatile uint8_t* addr) { uint32_t result; + #if (__GNUC__ > 4) || (__GNUC__ == 4 && __GNUC_MINOR__ >= 8) __ASM volatile ("ldrexb %0, %1" : "=r" (result) : "Q" (*addr) ); #else @@ -570,9 +1050,10 @@ __attribute__((always_inline)) __STATIC_INLINE uint8_t __LDREXB(volatile uint8_t \param [in] ptr Pointer to data \return value of type uint16_t at (*ptr) */ -__attribute__((always_inline)) __STATIC_INLINE uint16_t __LDREXH(volatile uint16_t* addr) +__STATIC_FORCEINLINE uint16_t __LDREXH(volatile uint16_t* addr) { uint32_t result; + #if (__GNUC__ > 4) || (__GNUC__ == 4 && __GNUC_MINOR__ >= 8) __ASM volatile ("ldrexh %0, %1" : "=r" (result) : "Q" (*addr) ); #else @@ -591,9 +1072,10 @@ __attribute__((always_inline)) __STATIC_INLINE uint16_t __LDREXH(volatile uint16 \param [in] ptr Pointer to data \return value of type uint32_t at (*ptr) */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __LDREXW(volatile uint32_t* addr) +__STATIC_FORCEINLINE uint32_t __LDREXW(volatile uint32_t* addr) { uint32_t result; + __ASM volatile ("ldrex %0, %1" : "=r" (result) : "Q" (*addr) ); return (result); } @@ -607,9 +1089,10 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __LDREXW(volatile uint32 \return 0 Function succeeded \return 1 Function failed */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __STREXB(uint8_t value, volatile uint8_t* addr) +__STATIC_FORCEINLINE uint32_t __STREXB(uint8_t value, volatile uint8_t* addr) { uint32_t result; + __ASM volatile ("strexb %0, %2, %1" : "=&r" (result), "=Q" (*addr) : "r" ((uint32_t)value) ); return (result); } @@ -623,9 +1106,10 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __STREXB(uint8_t value, \return 0 Function succeeded \return 1 Function failed */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __STREXH(uint16_t value, volatile uint16_t* addr) +__STATIC_FORCEINLINE uint32_t __STREXH(uint16_t value, volatile uint16_t* addr) { uint32_t result; + __ASM volatile ("strexh %0, %2, %1" : "=&r" (result), "=Q" (*addr) : "r" ((uint32_t)value) ); return (result); } @@ -639,9 +1123,10 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __STREXH(uint16_t value, \return 0 Function succeeded \return 1 Function failed */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __STREXW(uint32_t value, volatile uint32_t* addr) +__STATIC_FORCEINLINE uint32_t __STREXW(uint32_t value, volatile uint32_t* addr) { uint32_t result; + __ASM volatile ("strex %0, %2, %1" : "=&r" (result), "=Q" (*addr) : "r" (value) ); return (result); } @@ -651,22 +1136,31 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __STREXW(uint32_t value, \brief Remove the exclusive lock \details Removes the exclusive lock which is created by LDREX. */ -__attribute__((always_inline)) __STATIC_INLINE void __CLREX(void) +__STATIC_FORCEINLINE void __CLREX(void) { __ASM volatile ("clrex" ::: "memory"); } +#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__ ) && (__ARM_ARCH_7EM__ == 1)) || \ + (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \ + (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1)) ) */ + +#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__ ) && (__ARM_ARCH_7EM__ == 1)) || \ + (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) ) /** \brief Signed Saturate \details Saturates a signed value. - \param [in] value Value to be saturated - \param [in] sat Bit position to saturate to (1..32) + \param [in] ARG1 Value to be saturated + \param [in] ARG2 Bit position to saturate to (1..32) \return Saturated value */ #define __SSAT(ARG1,ARG2) \ +__extension__ \ ({ \ - uint32_t __RES, __ARG1 = (ARG1); \ + int32_t __RES, __ARG1 = (ARG1); \ __ASM ("ssat %0, %1, %2" : "=r" (__RES) : "I" (ARG2), "r" (__ARG1) ); \ __RES; \ }) @@ -675,11 +1169,12 @@ __attribute__((always_inline)) __STATIC_INLINE void __CLREX(void) /** \brief Unsigned Saturate \details Saturates an unsigned value. - \param [in] value Value to be saturated - \param [in] sat Bit position to saturate to (0..31) + \param [in] ARG1 Value to be saturated + \param [in] ARG2 Bit position to saturate to (0..31) \return Saturated value */ #define __USAT(ARG1,ARG2) \ + __extension__ \ ({ \ uint32_t __RES, __ARG1 = (ARG1); \ __ASM ("usat %0, %1, %2" : "=r" (__RES) : "I" (ARG2), "r" (__ARG1) ); \ @@ -694,9 +1189,10 @@ __attribute__((always_inline)) __STATIC_INLINE void __CLREX(void) \param [in] value Value to rotate \return Rotated value */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __RRX(uint32_t value) +__STATIC_FORCEINLINE uint32_t __RRX(uint32_t value) { uint32_t result; + __ASM volatile ("rrx %0, %1" : __CMSIS_GCC_OUT_REG (result) : __CMSIS_GCC_USE_REG (value) ); return (result); } @@ -708,16 +1204,17 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __RRX(uint32_t value) \param [in] ptr Pointer to data \return value of type uint8_t at (*ptr) */ -__attribute__((always_inline)) __STATIC_INLINE uint8_t __LDRBT(volatile uint8_t* addr) +__STATIC_FORCEINLINE uint8_t __LDRBT(volatile uint8_t* ptr) { uint32_t result; + #if (__GNUC__ > 4) || (__GNUC__ == 4 && __GNUC_MINOR__ >= 8) - __ASM volatile ("ldrbt %0, %1" : "=r" (result) : "Q" (*addr) ); + __ASM volatile ("ldrbt %0, %1" : "=r" (result) : "Q" (*ptr) ); #else /* Prior to GCC 4.8, "Q" will be expanded to [rx, #0] which is not accepted by assembler. So has to use following less efficient pattern. */ - __ASM volatile ("ldrbt %0, [%1]" : "=r" (result) : "r" (addr) : "memory" ); + __ASM volatile ("ldrbt %0, [%1]" : "=r" (result) : "r" (ptr) : "memory" ); #endif return ((uint8_t) result); /* Add explicit type cast here */ } @@ -729,16 +1226,17 @@ __attribute__((always_inline)) __STATIC_INLINE uint8_t __LDRBT(volatile uint8_t* \param [in] ptr Pointer to data \return value of type uint16_t at (*ptr) */ -__attribute__((always_inline)) __STATIC_INLINE uint16_t __LDRHT(volatile uint16_t* addr) +__STATIC_FORCEINLINE uint16_t __LDRHT(volatile uint16_t* ptr) { uint32_t result; + #if (__GNUC__ > 4) || (__GNUC__ == 4 && __GNUC_MINOR__ >= 8) - __ASM volatile ("ldrht %0, %1" : "=r" (result) : "Q" (*addr) ); + __ASM volatile ("ldrht %0, %1" : "=r" (result) : "Q" (*ptr) ); #else /* Prior to GCC 4.8, "Q" will be expanded to [rx, #0] which is not accepted by assembler. So has to use following less efficient pattern. */ - __ASM volatile ("ldrht %0, [%1]" : "=r" (result) : "r" (addr) : "memory" ); + __ASM volatile ("ldrht %0, [%1]" : "=r" (result) : "r" (ptr) : "memory" ); #endif return ((uint16_t) result); /* Add explicit type cast here */ } @@ -750,10 +1248,11 @@ __attribute__((always_inline)) __STATIC_INLINE uint16_t __LDRHT(volatile uint16_ \param [in] ptr Pointer to data \return value of type uint32_t at (*ptr) */ -__attribute__((always_inline)) __STATIC_INLINE uint32_t __LDRT(volatile uint32_t* addr) +__STATIC_FORCEINLINE uint32_t __LDRT(volatile uint32_t* ptr) { uint32_t result; - __ASM volatile ("ldrt %0, %1" : "=r" (result) : "Q" (*addr) ); + + __ASM volatile ("ldrt %0, %1" : "=r" (result) : "Q" (*ptr) ); return (result); } @@ -764,9 +1263,9 @@ __attribute__((always_inline)) __STATIC_INLINE uint32_t __LDRT(volatile uint32_t \param [in] value Value to store \param [in] ptr Pointer to location */ -__attribute__((always_inline)) __STATIC_INLINE void __STRBT(uint8_t value, volatile uint8_t* addr) +__STATIC_FORCEINLINE void __STRBT(uint8_t value, volatile uint8_t* ptr) { - __ASM volatile ("strbt %1, %0" : "=Q" (*addr) : "r" ((uint32_t)value) ); + __ASM volatile ("strbt %1, %0" : "=Q" (*ptr) : "r" ((uint32_t)value) ); } @@ -776,9 +1275,9 @@ __attribute__((always_inline)) __STATIC_INLINE void __STRBT(uint8_t value, volat \param [in] value Value to store \param [in] ptr Pointer to location */ -__attribute__((always_inline)) __STATIC_INLINE void __STRHT(uint16_t value, volatile uint16_t* addr) +__STATIC_FORCEINLINE void __STRHT(uint16_t value, volatile uint16_t* ptr) { - __ASM volatile ("strht %1, %0" : "=Q" (*addr) : "r" ((uint32_t)value) ); + __ASM volatile ("strht %1, %0" : "=Q" (*ptr) : "r" ((uint32_t)value) ); } @@ -788,12 +1287,253 @@ __attribute__((always_inline)) __STATIC_INLINE void __STRHT(uint16_t value, vola \param [in] value Value to store \param [in] ptr Pointer to location */ -__attribute__((always_inline)) __STATIC_INLINE void __STRT(uint32_t value, volatile uint32_t* addr) +__STATIC_FORCEINLINE void __STRT(uint32_t value, volatile uint32_t* ptr) +{ + __ASM volatile ("strt %1, %0" : "=Q" (*ptr) : "r" (value) ); +} + +#else /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__ ) && (__ARM_ARCH_7EM__ == 1)) || \ + (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) ) */ + +/** + \brief Signed Saturate + \details Saturates a signed value. + \param [in] value Value to be saturated + \param [in] sat Bit position to saturate to (1..32) + \return Saturated value + */ +__STATIC_FORCEINLINE int32_t __SSAT(int32_t val, uint32_t sat) +{ + if ((sat >= 1U) && (sat <= 32U)) + { + const int32_t max = (int32_t)((1U << (sat - 1U)) - 1U); + const int32_t min = -1 - max ; + + if (val > max) + { + return max; + } + else if (val < min) + { + return min; + } + } + + return val; +} + +/** + \brief Unsigned Saturate + \details Saturates an unsigned value. + \param [in] value Value to be saturated + \param [in] sat Bit position to saturate to (0..31) + \return Saturated value + */ +__STATIC_FORCEINLINE uint32_t __USAT(int32_t val, uint32_t sat) +{ + if (sat <= 31U) + { + const uint32_t max = ((1U << sat) - 1U); + + if (val > (int32_t)max) + { + return max; + } + else if (val < 0) + { + return 0U; + } + } + + return (uint32_t)val; +} + +#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__ == 1)) || \ + (defined (__ARM_ARCH_7EM__ ) && (__ARM_ARCH_7EM__ == 1)) || \ + (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) ) */ + + +#if ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \ + (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1)) ) +/** + \brief Load-Acquire (8 bit) + \details Executes a LDAB instruction for 8 bit value. + \param [in] ptr Pointer to data + \return value of type uint8_t at (*ptr) + */ +__STATIC_FORCEINLINE uint8_t __LDAB(volatile uint8_t* ptr) +{ + uint32_t result; + + __ASM volatile ("ldab %0, %1" : "=r" (result) : "Q" (*ptr) ); + return ((uint8_t) result); +} + + +/** + \brief Load-Acquire (16 bit) + \details Executes a LDAH instruction for 16 bit values. + \param [in] ptr Pointer to data + \return value of type uint16_t at (*ptr) + */ +__STATIC_FORCEINLINE uint16_t __LDAH(volatile uint16_t* ptr) +{ + uint32_t result; + + __ASM volatile ("ldah %0, %1" : "=r" (result) : "Q" (*ptr) ); + return ((uint16_t) result); +} + + +/** + \brief Load-Acquire (32 bit) + \details Executes a LDA instruction for 32 bit values. + \param [in] ptr Pointer to data + \return value of type uint32_t at (*ptr) + */ +__STATIC_FORCEINLINE uint32_t __LDA(volatile uint32_t* ptr) +{ + uint32_t result; + + __ASM volatile ("lda %0, %1" : "=r" (result) : "Q" (*ptr) ); + return (result); +} + + +/** + \brief Store-Release (8 bit) + \details Executes a STLB instruction for 8 bit values. + \param [in] value Value to store + \param [in] ptr Pointer to location + */ +__STATIC_FORCEINLINE void __STLB(uint8_t value, volatile uint8_t* ptr) +{ + __ASM volatile ("stlb %1, %0" : "=Q" (*ptr) : "r" ((uint32_t)value) ); +} + + +/** + \brief Store-Release (16 bit) + \details Executes a STLH instruction for 16 bit values. + \param [in] value Value to store + \param [in] ptr Pointer to location + */ +__STATIC_FORCEINLINE void __STLH(uint16_t value, volatile uint16_t* ptr) +{ + __ASM volatile ("stlh %1, %0" : "=Q" (*ptr) : "r" ((uint32_t)value) ); +} + + +/** + \brief Store-Release (32 bit) + \details Executes a STL instruction for 32 bit values. + \param [in] value Value to store + \param [in] ptr Pointer to location + */ +__STATIC_FORCEINLINE void __STL(uint32_t value, volatile uint32_t* ptr) +{ + __ASM volatile ("stl %1, %0" : "=Q" (*ptr) : "r" ((uint32_t)value) ); +} + + +/** + \brief Load-Acquire Exclusive (8 bit) + \details Executes a LDAB exclusive instruction for 8 bit value. + \param [in] ptr Pointer to data + \return value of type uint8_t at (*ptr) + */ +__STATIC_FORCEINLINE uint8_t __LDAEXB(volatile uint8_t* ptr) +{ + uint32_t result; + + __ASM volatile ("ldaexb %0, %1" : "=r" (result) : "Q" (*ptr) ); + return ((uint8_t) result); +} + + +/** + \brief Load-Acquire Exclusive (16 bit) + \details Executes a LDAH exclusive instruction for 16 bit values. + \param [in] ptr Pointer to data + \return value of type uint16_t at (*ptr) + */ +__STATIC_FORCEINLINE uint16_t __LDAEXH(volatile uint16_t* ptr) +{ + uint32_t result; + + __ASM volatile ("ldaexh %0, %1" : "=r" (result) : "Q" (*ptr) ); + return ((uint16_t) result); +} + + +/** + \brief Load-Acquire Exclusive (32 bit) + \details Executes a LDA exclusive instruction for 32 bit values. + \param [in] ptr Pointer to data + \return value of type uint32_t at (*ptr) + */ +__STATIC_FORCEINLINE uint32_t __LDAEX(volatile uint32_t* ptr) +{ + uint32_t result; + + __ASM volatile ("ldaex %0, %1" : "=r" (result) : "Q" (*ptr) ); + return (result); +} + + +/** + \brief Store-Release Exclusive (8 bit) + \details Executes a STLB exclusive instruction for 8 bit values. + \param [in] value Value to store + \param [in] ptr Pointer to location + \return 0 Function succeeded + \return 1 Function failed + */ +__STATIC_FORCEINLINE uint32_t __STLEXB(uint8_t value, volatile uint8_t* ptr) +{ + uint32_t result; + + __ASM volatile ("stlexb %0, %2, %1" : "=&r" (result), "=Q" (*ptr) : "r" ((uint32_t)value) ); + return (result); +} + + +/** + \brief Store-Release Exclusive (16 bit) + \details Executes a STLH exclusive instruction for 16 bit values. + \param [in] value Value to store + \param [in] ptr Pointer to location + \return 0 Function succeeded + \return 1 Function failed + */ +__STATIC_FORCEINLINE uint32_t __STLEXH(uint16_t value, volatile uint16_t* ptr) +{ + uint32_t result; + + __ASM volatile ("stlexh %0, %2, %1" : "=&r" (result), "=Q" (*ptr) : "r" ((uint32_t)value) ); + return (result); +} + + +/** + \brief Store-Release Exclusive (32 bit) + \details Executes a STL exclusive instruction for 32 bit values. + \param [in] value Value to store + \param [in] ptr Pointer to location + \return 0 Function succeeded + \return 1 Function failed + */ +__STATIC_FORCEINLINE uint32_t __STLEX(uint32_t value, volatile uint32_t* ptr) { - __ASM volatile ("strt %1, %0" : "=Q" (*addr) : "r" (value) ); + uint32_t result; + + __ASM volatile ("stlex %0, %2, %1" : "=&r" (result), "=Q" (*ptr) : "r" ((uint32_t)value) ); + return (result); } -#endif /* (__CORTEX_M >= 0x03U) || (__CORTEX_SC >= 300U) */ +#endif /* ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \ + (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1)) ) */ /*@}*/ /* end of group CMSIS_Core_InstructionInterface */ @@ -804,272 +1544,310 @@ __attribute__((always_inline)) __STATIC_INLINE void __STRT(uint32_t value, volat @{ */ -#if (__CORTEX_M >= 0x04U) /* only for Cortex-M4 and above */ +#if (defined (__ARM_FEATURE_DSP) && (__ARM_FEATURE_DSP == 1)) -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SADD8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SADD8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("sadd8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __QADD8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __QADD8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("qadd8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SHADD8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SHADD8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("shadd8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UADD8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UADD8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uadd8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UQADD8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UQADD8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uqadd8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UHADD8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UHADD8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uhadd8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SSUB8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SSUB8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("ssub8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __QSUB8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __QSUB8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("qsub8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SHSUB8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SHSUB8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("shsub8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __USUB8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __USUB8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("usub8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UQSUB8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UQSUB8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uqsub8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UHSUB8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UHSUB8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uhsub8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SADD16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SADD16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("sadd16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __QADD16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __QADD16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("qadd16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SHADD16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SHADD16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("shadd16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UADD16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UADD16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uadd16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UQADD16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UQADD16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uqadd16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UHADD16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UHADD16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uhadd16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SSUB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SSUB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("ssub16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __QSUB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __QSUB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("qsub16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SHSUB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SHSUB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("shsub16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __USUB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __USUB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("usub16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UQSUB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UQSUB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uqsub16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UHSUB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UHSUB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uhsub16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SASX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SASX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("sasx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __QASX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __QASX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("qasx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SHASX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SHASX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("shasx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UASX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UASX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uasx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UQASX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UQASX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uqasx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UHASX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UHASX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uhasx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SSAX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SSAX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("ssax %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __QSAX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __QSAX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("qsax %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SHSAX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SHSAX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("shsax %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __USAX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __USAX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("usax %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UQSAX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UQSAX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uqsax %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UHSAX(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UHSAX(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uhsax %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __USAD8(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __USAD8(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("usad8 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __USADA8(uint32_t op1, uint32_t op2, uint32_t op3) +__STATIC_FORCEINLINE uint32_t __USADA8(uint32_t op1, uint32_t op2, uint32_t op3) { uint32_t result; + __ASM volatile ("usada8 %0, %1, %2, %3" : "=r" (result) : "r" (op1), "r" (op2), "r" (op3) ); return (result); } @@ -1088,63 +1866,71 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __USADA8(uint32_t op __RES; \ }) -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UXTB16(uint32_t op1) +__STATIC_FORCEINLINE uint32_t __UXTB16(uint32_t op1) { uint32_t result; + __ASM volatile ("uxtb16 %0, %1" : "=r" (result) : "r" (op1)); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __UXTAB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __UXTAB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("uxtab16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SXTB16(uint32_t op1) +__STATIC_FORCEINLINE uint32_t __SXTB16(uint32_t op1) { uint32_t result; + __ASM volatile ("sxtb16 %0, %1" : "=r" (result) : "r" (op1)); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SXTAB16(uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SXTAB16(uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("sxtab16 %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SMUAD (uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SMUAD (uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("smuad %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SMUADX (uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SMUADX (uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("smuadx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SMLAD (uint32_t op1, uint32_t op2, uint32_t op3) +__STATIC_FORCEINLINE uint32_t __SMLAD (uint32_t op1, uint32_t op2, uint32_t op3) { uint32_t result; + __ASM volatile ("smlad %0, %1, %2, %3" : "=r" (result) : "r" (op1), "r" (op2), "r" (op3) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SMLADX (uint32_t op1, uint32_t op2, uint32_t op3) +__STATIC_FORCEINLINE uint32_t __SMLADX (uint32_t op1, uint32_t op2, uint32_t op3) { uint32_t result; + __ASM volatile ("smladx %0, %1, %2, %3" : "=r" (result) : "r" (op1), "r" (op2), "r" (op3) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint64_t __SMLALD (uint32_t op1, uint32_t op2, uint64_t acc) +__STATIC_FORCEINLINE uint64_t __SMLALD (uint32_t op1, uint32_t op2, uint64_t acc) { union llreg_u { @@ -1152,15 +1938,17 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE uint64_t __SMLALD (uint32_t o uint64_t w64; } llr; llr.w64 = acc; + #ifndef __ARMEB__ /* Little endian */ __ASM volatile ("smlald %0, %1, %2, %3" : "=r" (llr.w32[0]), "=r" (llr.w32[1]): "r" (op1), "r" (op2), "0" (llr.w32[0]), "1" (llr.w32[1]) ); #else /* Big endian */ __ASM volatile ("smlald %0, %1, %2, %3" : "=r" (llr.w32[1]), "=r" (llr.w32[0]): "r" (op1), "r" (op2), "0" (llr.w32[1]), "1" (llr.w32[0]) ); #endif + return (llr.w64); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint64_t __SMLALDX (uint32_t op1, uint32_t op2, uint64_t acc) +__STATIC_FORCEINLINE uint64_t __SMLALDX (uint32_t op1, uint32_t op2, uint64_t acc) { union llreg_u { @@ -1168,43 +1956,49 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE uint64_t __SMLALDX (uint32_t uint64_t w64; } llr; llr.w64 = acc; + #ifndef __ARMEB__ /* Little endian */ __ASM volatile ("smlaldx %0, %1, %2, %3" : "=r" (llr.w32[0]), "=r" (llr.w32[1]): "r" (op1), "r" (op2), "0" (llr.w32[0]), "1" (llr.w32[1]) ); #else /* Big endian */ __ASM volatile ("smlaldx %0, %1, %2, %3" : "=r" (llr.w32[1]), "=r" (llr.w32[0]): "r" (op1), "r" (op2), "0" (llr.w32[1]), "1" (llr.w32[0]) ); #endif + return (llr.w64); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SMUSD (uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SMUSD (uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("smusd %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SMUSDX (uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SMUSDX (uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("smusdx %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SMLSD (uint32_t op1, uint32_t op2, uint32_t op3) +__STATIC_FORCEINLINE uint32_t __SMLSD (uint32_t op1, uint32_t op2, uint32_t op3) { uint32_t result; + __ASM volatile ("smlsd %0, %1, %2, %3" : "=r" (result) : "r" (op1), "r" (op2), "r" (op3) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SMLSDX (uint32_t op1, uint32_t op2, uint32_t op3) +__STATIC_FORCEINLINE uint32_t __SMLSDX (uint32_t op1, uint32_t op2, uint32_t op3) { uint32_t result; + __ASM volatile ("smlsdx %0, %1, %2, %3" : "=r" (result) : "r" (op1), "r" (op2), "r" (op3) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint64_t __SMLSLD (uint32_t op1, uint32_t op2, uint64_t acc) +__STATIC_FORCEINLINE uint64_t __SMLSLD (uint32_t op1, uint32_t op2, uint64_t acc) { union llreg_u { @@ -1212,15 +2006,17 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE uint64_t __SMLSLD (uint32_t o uint64_t w64; } llr; llr.w64 = acc; + #ifndef __ARMEB__ /* Little endian */ __ASM volatile ("smlsld %0, %1, %2, %3" : "=r" (llr.w32[0]), "=r" (llr.w32[1]): "r" (op1), "r" (op2), "0" (llr.w32[0]), "1" (llr.w32[1]) ); #else /* Big endian */ __ASM volatile ("smlsld %0, %1, %2, %3" : "=r" (llr.w32[1]), "=r" (llr.w32[0]): "r" (op1), "r" (op2), "0" (llr.w32[1]), "1" (llr.w32[0]) ); #endif + return (llr.w64); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint64_t __SMLSLDX (uint32_t op1, uint32_t op2, uint64_t acc) +__STATIC_FORCEINLINE uint64_t __SMLSLDX (uint32_t op1, uint32_t op2, uint64_t acc) { union llreg_u { @@ -1228,35 +2024,41 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE uint64_t __SMLSLDX (uint32_t uint64_t w64; } llr; llr.w64 = acc; + #ifndef __ARMEB__ /* Little endian */ __ASM volatile ("smlsldx %0, %1, %2, %3" : "=r" (llr.w32[0]), "=r" (llr.w32[1]): "r" (op1), "r" (op2), "0" (llr.w32[0]), "1" (llr.w32[1]) ); #else /* Big endian */ __ASM volatile ("smlsldx %0, %1, %2, %3" : "=r" (llr.w32[1]), "=r" (llr.w32[0]): "r" (op1), "r" (op2), "0" (llr.w32[1]), "1" (llr.w32[0]) ); #endif + return (llr.w64); } -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SEL (uint32_t op1, uint32_t op2) +__STATIC_FORCEINLINE uint32_t __SEL (uint32_t op1, uint32_t op2) { uint32_t result; + __ASM volatile ("sel %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE int32_t __QADD( int32_t op1, int32_t op2) +__STATIC_FORCEINLINE int32_t __QADD( int32_t op1, int32_t op2) { int32_t result; + __ASM volatile ("qadd %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } -__attribute__( ( always_inline ) ) __STATIC_INLINE int32_t __QSUB( int32_t op1, int32_t op2) +__STATIC_FORCEINLINE int32_t __QSUB( int32_t op1, int32_t op2) { int32_t result; + __ASM volatile ("qsub %0, %1, %2" : "=r" (result) : "r" (op1), "r" (op2) ); return (result); } +#if 0 #define __PKHBT(ARG1,ARG2,ARG3) \ ({ \ uint32_t __RES, __ARG1 = (ARG1), __ARG2 = (ARG2); \ @@ -1273,20 +2075,26 @@ __attribute__( ( always_inline ) ) __STATIC_INLINE int32_t __QSUB( int32_t op1, __ASM ("pkhtb %0, %1, %2, asr %3" : "=r" (__RES) : "r" (__ARG1), "r" (__ARG2), "I" (ARG3) ); \ __RES; \ }) +#endif -__attribute__( ( always_inline ) ) __STATIC_INLINE uint32_t __SMMLA (int32_t op1, int32_t op2, int32_t op3) +#define __PKHBT(ARG1,ARG2,ARG3) ( ((((uint32_t)(ARG1)) ) & 0x0000FFFFUL) | \ + ((((uint32_t)(ARG2)) << (ARG3)) & 0xFFFF0000UL) ) + +#define __PKHTB(ARG1,ARG2,ARG3) ( ((((uint32_t)(ARG1)) ) & 0xFFFF0000UL) | \ + ((((uint32_t)(ARG2)) >> (ARG3)) & 0x0000FFFFUL) ) + +__STATIC_FORCEINLINE int32_t __SMMLA (int32_t op1, int32_t op2, int32_t op3) { int32_t result; + __ASM volatile ("smmla %0, %1, %2, %3" : "=r" (result): "r" (op1), "r" (op2), "r" (op3) ); return (result); } -#endif /* (__CORTEX_M >= 0x04) */ +#endif /* (__ARM_FEATURE_DSP == 1) */ /*@} end of group CMSIS_SIMD_intrinsics */ -#if defined ( __GNUC__ ) #pragma GCC diagnostic pop -#endif #endif /* __CMSIS_GCC_H */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/cmsis_iccarm.h b/EpsilonLights/Drivers/CMSIS/Include/cmsis_iccarm.h new file mode 100644 index 00000000..7e7df092 --- /dev/null +++ b/EpsilonLights/Drivers/CMSIS/Include/cmsis_iccarm.h @@ -0,0 +1,948 @@ +/**************************************************************************//** + * @file cmsis_iccarm.h + * @brief CMSIS compiler ICCARM (IAR Compiler for Arm) header file + * @version V5.0.7 + * @date 19. June 2018 + ******************************************************************************/ + +//------------------------------------------------------------------------------ +// +// Copyright (c) 2017-2018 IAR Systems +// +// Licensed under the Apache License, Version 2.0 (the "License") +// you may not use this file except in compliance with the License. +// You may obtain a copy of the License at +// http://www.apache.org/licenses/LICENSE-2.0 +// +// Unless required by applicable law or agreed to in writing, software +// distributed under the License is distributed on an "AS IS" BASIS, +// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +// See the License for the specific language governing permissions and +// limitations under the License. +// +//------------------------------------------------------------------------------ + + +#ifndef __CMSIS_ICCARM_H__ +#define __CMSIS_ICCARM_H__ + +#ifndef __ICCARM__ +#error This file should only be compiled by ICCARM +#endif + +#pragma system_include + +#define __IAR_FT _Pragma("inline=forced") __intrinsic + +#if (__VER__ >= 8000000) +#define __ICCARM_V8 1 +#else +#define __ICCARM_V8 0 +#endif + +#ifndef __ALIGNED +#if __ICCARM_V8 +#define __ALIGNED(x) __attribute__((aligned(x))) +#elif (__VER__ >= 7080000) +/* Needs IAR language extensions */ +#define __ALIGNED(x) __attribute__((aligned(x))) +#else +#warning No compiler specific solution for __ALIGNED.__ALIGNED is ignored. +#define __ALIGNED(x) +#endif +#endif + + +/* Define compiler macros for CPU architecture, used in CMSIS 5. + */ +#if __ARM_ARCH_6M__ || __ARM_ARCH_7M__ || __ARM_ARCH_7EM__ || __ARM_ARCH_8M_BASE__ || __ARM_ARCH_8M_MAIN__ +/* Macros already defined */ +#else +#if defined(__ARM8M_MAINLINE__) || defined(__ARM8EM_MAINLINE__) +#define __ARM_ARCH_8M_MAIN__ 1 +#elif defined(__ARM8M_BASELINE__) +#define __ARM_ARCH_8M_BASE__ 1 +#elif defined(__ARM_ARCH_PROFILE) && __ARM_ARCH_PROFILE == 'M' +#if __ARM_ARCH == 6 +#define __ARM_ARCH_6M__ 1 +#elif __ARM_ARCH == 7 +#if __ARM_FEATURE_DSP +#define __ARM_ARCH_7EM__ 1 +#else +#define __ARM_ARCH_7M__ 1 +#endif +#endif /* __ARM_ARCH */ +#endif /* __ARM_ARCH_PROFILE == 'M' */ +#endif + +/* Alternativ core deduction for older ICCARM's */ +#if !defined(__ARM_ARCH_6M__) && !defined(__ARM_ARCH_7M__) && !defined(__ARM_ARCH_7EM__) && \ + !defined(__ARM_ARCH_8M_BASE__) && !defined(__ARM_ARCH_8M_MAIN__) +#if defined(__ARM6M__) && (__CORE__ == __ARM6M__) +#define __ARM_ARCH_6M__ 1 +#elif defined(__ARM7M__) && (__CORE__ == __ARM7M__) +#define __ARM_ARCH_7M__ 1 +#elif defined(__ARM7EM__) && (__CORE__ == __ARM7EM__) +#define __ARM_ARCH_7EM__ 1 +#elif defined(__ARM8M_BASELINE__) && (__CORE == __ARM8M_BASELINE__) +#define __ARM_ARCH_8M_BASE__ 1 +#elif defined(__ARM8M_MAINLINE__) && (__CORE == __ARM8M_MAINLINE__) +#define __ARM_ARCH_8M_MAIN__ 1 +#elif defined(__ARM8EM_MAINLINE__) && (__CORE == __ARM8EM_MAINLINE__) +#define __ARM_ARCH_8M_MAIN__ 1 +#else +#error "Unknown target." +#endif +#endif + + + +#if defined(__ARM_ARCH_6M__) && __ARM_ARCH_6M__==1 +#define __IAR_M0_FAMILY 1 +#elif defined(__ARM_ARCH_8M_BASE__) && __ARM_ARCH_8M_BASE__==1 +#define __IAR_M0_FAMILY 1 +#else +#define __IAR_M0_FAMILY 0 +#endif + + +#ifndef __ASM +#define __ASM __asm +#endif + +#ifndef __INLINE +#define __INLINE inline +#endif + +#ifndef __NO_RETURN +#if __ICCARM_V8 +#define __NO_RETURN __attribute__((__noreturn__)) +#else +#define __NO_RETURN _Pragma("object_attribute=__noreturn") +#endif +#endif + +#ifndef __PACKED +#if __ICCARM_V8 +#define __PACKED __attribute__((packed, aligned(1))) +#else +/* Needs IAR language extensions */ +#define __PACKED __packed +#endif +#endif + +#ifndef __PACKED_STRUCT +#if __ICCARM_V8 +#define __PACKED_STRUCT struct __attribute__((packed, aligned(1))) +#else +/* Needs IAR language extensions */ +#define __PACKED_STRUCT __packed struct +#endif +#endif + +#ifndef __PACKED_UNION +#if __ICCARM_V8 +#define __PACKED_UNION union __attribute__((packed, aligned(1))) +#else +/* Needs IAR language extensions */ +#define __PACKED_UNION __packed union +#endif +#endif + +#ifndef __RESTRICT +#define __RESTRICT __restrict +#endif + +#ifndef __STATIC_INLINE +#define __STATIC_INLINE static inline +#endif + +#ifndef __FORCEINLINE +#define __FORCEINLINE _Pragma("inline=forced") +#endif + +#ifndef __STATIC_FORCEINLINE +#define __STATIC_FORCEINLINE __FORCEINLINE __STATIC_INLINE +#endif + +#ifndef __UNALIGNED_UINT16_READ +#pragma language=save +#pragma language=extended +__IAR_FT uint16_t __iar_uint16_read(void const* ptr) +{ + return *(__packed uint16_t*)(ptr); +} +#pragma language=restore +#define __UNALIGNED_UINT16_READ(PTR) __iar_uint16_read(PTR) +#endif + + +#ifndef __UNALIGNED_UINT16_WRITE +#pragma language=save +#pragma language=extended +__IAR_FT void __iar_uint16_write(void const* ptr, uint16_t val) +{ + *(__packed uint16_t*)(ptr) = val;; +} +#pragma language=restore +#define __UNALIGNED_UINT16_WRITE(PTR,VAL) __iar_uint16_write(PTR,VAL) +#endif + +#ifndef __UNALIGNED_UINT32_READ +#pragma language=save +#pragma language=extended +__IAR_FT uint32_t __iar_uint32_read(void const* ptr) +{ + return *(__packed uint32_t*)(ptr); +} +#pragma language=restore +#define __UNALIGNED_UINT32_READ(PTR) __iar_uint32_read(PTR) +#endif + +#ifndef __UNALIGNED_UINT32_WRITE +#pragma language=save +#pragma language=extended +__IAR_FT void __iar_uint32_write(void const* ptr, uint32_t val) +{ + *(__packed uint32_t*)(ptr) = val;; +} +#pragma language=restore +#define __UNALIGNED_UINT32_WRITE(PTR,VAL) __iar_uint32_write(PTR,VAL) +#endif + +#ifndef __UNALIGNED_UINT32 /* deprecated */ +#pragma language=save +#pragma language=extended +__packed struct __iar_u32 +{ + uint32_t v; +}; +#pragma language=restore +#define __UNALIGNED_UINT32(PTR) (((struct __iar_u32 *)(PTR))->v) +#endif + +#ifndef __USED +#if __ICCARM_V8 +#define __USED __attribute__((used)) +#else +#define __USED _Pragma("__root") +#endif +#endif + +#ifndef __WEAK +#if __ICCARM_V8 +#define __WEAK __attribute__((weak)) +#else +#define __WEAK _Pragma("__weak") +#endif +#endif + + +#ifndef __ICCARM_INTRINSICS_VERSION__ +#define __ICCARM_INTRINSICS_VERSION__ 0 +#endif + +#if __ICCARM_INTRINSICS_VERSION__ == 2 + +#if defined(__CLZ) +#undef __CLZ +#endif +#if defined(__REVSH) +#undef __REVSH +#endif +#if defined(__RBIT) +#undef __RBIT +#endif +#if defined(__SSAT) +#undef __SSAT +#endif +#if defined(__USAT) +#undef __USAT +#endif + +#include "iccarm_builtin.h" + +#define __disable_fault_irq __iar_builtin_disable_fiq +#define __disable_irq __iar_builtin_disable_interrupt +#define __enable_fault_irq __iar_builtin_enable_fiq +#define __enable_irq __iar_builtin_enable_interrupt +#define __arm_rsr __iar_builtin_rsr +#define __arm_wsr __iar_builtin_wsr + + +#define __get_APSR() (__arm_rsr("APSR")) +#define __get_BASEPRI() (__arm_rsr("BASEPRI")) +#define __get_CONTROL() (__arm_rsr("CONTROL")) +#define __get_FAULTMASK() (__arm_rsr("FAULTMASK")) + +#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \ + (defined (__FPU_USED ) && (__FPU_USED == 1U)) ) +#define __get_FPSCR() (__arm_rsr("FPSCR")) +#define __set_FPSCR(VALUE) (__arm_wsr("FPSCR", (VALUE))) +#else +#define __get_FPSCR() ( 0 ) +#define __set_FPSCR(VALUE) ((void)VALUE) +#endif + +#define __get_IPSR() (__arm_rsr("IPSR")) +#define __get_MSP() (__arm_rsr("MSP")) +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3))) +// without main extensions, the non-secure MSPLIM is RAZ/WI +#define __get_MSPLIM() (0U) +#else +#define __get_MSPLIM() (__arm_rsr("MSPLIM")) +#endif +#define __get_PRIMASK() (__arm_rsr("PRIMASK")) +#define __get_PSP() (__arm_rsr("PSP")) + +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3))) +// without main extensions, the non-secure PSPLIM is RAZ/WI +#define __get_PSPLIM() (0U) +#else +#define __get_PSPLIM() (__arm_rsr("PSPLIM")) +#endif + +#define __get_xPSR() (__arm_rsr("xPSR")) + +#define __set_BASEPRI(VALUE) (__arm_wsr("BASEPRI", (VALUE))) +#define __set_BASEPRI_MAX(VALUE) (__arm_wsr("BASEPRI_MAX", (VALUE))) +#define __set_CONTROL(VALUE) (__arm_wsr("CONTROL", (VALUE))) +#define __set_FAULTMASK(VALUE) (__arm_wsr("FAULTMASK", (VALUE))) +#define __set_MSP(VALUE) (__arm_wsr("MSP", (VALUE))) + +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3))) +// without main extensions, the non-secure MSPLIM is RAZ/WI +#define __set_MSPLIM(VALUE) ((void)(VALUE)) +#else +#define __set_MSPLIM(VALUE) (__arm_wsr("MSPLIM", (VALUE))) +#endif +#define __set_PRIMASK(VALUE) (__arm_wsr("PRIMASK", (VALUE))) +#define __set_PSP(VALUE) (__arm_wsr("PSP", (VALUE))) +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3))) +// without main extensions, the non-secure PSPLIM is RAZ/WI +#define __set_PSPLIM(VALUE) ((void)(VALUE)) +#else +#define __set_PSPLIM(VALUE) (__arm_wsr("PSPLIM", (VALUE))) +#endif + +#define __TZ_get_CONTROL_NS() (__arm_rsr("CONTROL_NS")) +#define __TZ_set_CONTROL_NS(VALUE) (__arm_wsr("CONTROL_NS", (VALUE))) +#define __TZ_get_PSP_NS() (__arm_rsr("PSP_NS")) +#define __TZ_set_PSP_NS(VALUE) (__arm_wsr("PSP_NS", (VALUE))) +#define __TZ_get_MSP_NS() (__arm_rsr("MSP_NS")) +#define __TZ_set_MSP_NS(VALUE) (__arm_wsr("MSP_NS", (VALUE))) +#define __TZ_get_SP_NS() (__arm_rsr("SP_NS")) +#define __TZ_set_SP_NS(VALUE) (__arm_wsr("SP_NS", (VALUE))) +#define __TZ_get_PRIMASK_NS() (__arm_rsr("PRIMASK_NS")) +#define __TZ_set_PRIMASK_NS(VALUE) (__arm_wsr("PRIMASK_NS", (VALUE))) +#define __TZ_get_BASEPRI_NS() (__arm_rsr("BASEPRI_NS")) +#define __TZ_set_BASEPRI_NS(VALUE) (__arm_wsr("BASEPRI_NS", (VALUE))) +#define __TZ_get_FAULTMASK_NS() (__arm_rsr("FAULTMASK_NS")) +#define __TZ_set_FAULTMASK_NS(VALUE)(__arm_wsr("FAULTMASK_NS", (VALUE))) + +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3))) +// without main extensions, the non-secure PSPLIM is RAZ/WI +#define __TZ_get_PSPLIM_NS() (0U) +#define __TZ_set_PSPLIM_NS(VALUE) ((void)(VALUE)) +#else +#define __TZ_get_PSPLIM_NS() (__arm_rsr("PSPLIM_NS")) +#define __TZ_set_PSPLIM_NS(VALUE) (__arm_wsr("PSPLIM_NS", (VALUE))) +#endif + +#define __TZ_get_MSPLIM_NS() (__arm_rsr("MSPLIM_NS")) +#define __TZ_set_MSPLIM_NS(VALUE) (__arm_wsr("MSPLIM_NS", (VALUE))) + +#define __NOP __iar_builtin_no_operation + +#define __CLZ __iar_builtin_CLZ +#define __CLREX __iar_builtin_CLREX + +#define __DMB __iar_builtin_DMB +#define __DSB __iar_builtin_DSB +#define __ISB __iar_builtin_ISB + +#define __LDREXB __iar_builtin_LDREXB +#define __LDREXH __iar_builtin_LDREXH +#define __LDREXW __iar_builtin_LDREX + +#define __RBIT __iar_builtin_RBIT +#define __REV __iar_builtin_REV +#define __REV16 __iar_builtin_REV16 + +__IAR_FT int16_t __REVSH(int16_t val) +{ + return (int16_t) __iar_builtin_REVSH(val); +} + +#define __ROR __iar_builtin_ROR +#define __RRX __iar_builtin_RRX + +#define __SEV __iar_builtin_SEV + +#if !__IAR_M0_FAMILY +#define __SSAT __iar_builtin_SSAT +#endif + +#define __STREXB __iar_builtin_STREXB +#define __STREXH __iar_builtin_STREXH +#define __STREXW __iar_builtin_STREX + +#if !__IAR_M0_FAMILY +#define __USAT __iar_builtin_USAT +#endif + +#define __WFE __iar_builtin_WFE +#define __WFI __iar_builtin_WFI + +#if __ARM_MEDIA__ +#define __SADD8 __iar_builtin_SADD8 +#define __QADD8 __iar_builtin_QADD8 +#define __SHADD8 __iar_builtin_SHADD8 +#define __UADD8 __iar_builtin_UADD8 +#define __UQADD8 __iar_builtin_UQADD8 +#define __UHADD8 __iar_builtin_UHADD8 +#define __SSUB8 __iar_builtin_SSUB8 +#define __QSUB8 __iar_builtin_QSUB8 +#define __SHSUB8 __iar_builtin_SHSUB8 +#define __USUB8 __iar_builtin_USUB8 +#define __UQSUB8 __iar_builtin_UQSUB8 +#define __UHSUB8 __iar_builtin_UHSUB8 +#define __SADD16 __iar_builtin_SADD16 +#define __QADD16 __iar_builtin_QADD16 +#define __SHADD16 __iar_builtin_SHADD16 +#define __UADD16 __iar_builtin_UADD16 +#define __UQADD16 __iar_builtin_UQADD16 +#define __UHADD16 __iar_builtin_UHADD16 +#define __SSUB16 __iar_builtin_SSUB16 +#define __QSUB16 __iar_builtin_QSUB16 +#define __SHSUB16 __iar_builtin_SHSUB16 +#define __USUB16 __iar_builtin_USUB16 +#define __UQSUB16 __iar_builtin_UQSUB16 +#define __UHSUB16 __iar_builtin_UHSUB16 +#define __SASX __iar_builtin_SASX +#define __QASX __iar_builtin_QASX +#define __SHASX __iar_builtin_SHASX +#define __UASX __iar_builtin_UASX +#define __UQASX __iar_builtin_UQASX +#define __UHASX __iar_builtin_UHASX +#define __SSAX __iar_builtin_SSAX +#define __QSAX __iar_builtin_QSAX +#define __SHSAX __iar_builtin_SHSAX +#define __USAX __iar_builtin_USAX +#define __UQSAX __iar_builtin_UQSAX +#define __UHSAX __iar_builtin_UHSAX +#define __USAD8 __iar_builtin_USAD8 +#define __USADA8 __iar_builtin_USADA8 +#define __SSAT16 __iar_builtin_SSAT16 +#define __USAT16 __iar_builtin_USAT16 +#define __UXTB16 __iar_builtin_UXTB16 +#define __UXTAB16 __iar_builtin_UXTAB16 +#define __SXTB16 __iar_builtin_SXTB16 +#define __SXTAB16 __iar_builtin_SXTAB16 +#define __SMUAD __iar_builtin_SMUAD +#define __SMUADX __iar_builtin_SMUADX +#define __SMMLA __iar_builtin_SMMLA +#define __SMLAD __iar_builtin_SMLAD +#define __SMLADX __iar_builtin_SMLADX +#define __SMLALD __iar_builtin_SMLALD +#define __SMLALDX __iar_builtin_SMLALDX +#define __SMUSD __iar_builtin_SMUSD +#define __SMUSDX __iar_builtin_SMUSDX +#define __SMLSD __iar_builtin_SMLSD +#define __SMLSDX __iar_builtin_SMLSDX +#define __SMLSLD __iar_builtin_SMLSLD +#define __SMLSLDX __iar_builtin_SMLSLDX +#define __SEL __iar_builtin_SEL +#define __QADD __iar_builtin_QADD +#define __QSUB __iar_builtin_QSUB +#define __PKHBT __iar_builtin_PKHBT +#define __PKHTB __iar_builtin_PKHTB +#endif + +#else /* __ICCARM_INTRINSICS_VERSION__ == 2 */ + +#if __IAR_M0_FAMILY +/* Avoid clash between intrinsics.h and arm_math.h when compiling for Cortex-M0. */ +#define __CLZ __cmsis_iar_clz_not_active +#define __SSAT __cmsis_iar_ssat_not_active +#define __USAT __cmsis_iar_usat_not_active +#define __RBIT __cmsis_iar_rbit_not_active +#define __get_APSR __cmsis_iar_get_APSR_not_active +#endif + + +#if (!((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \ + (defined (__FPU_USED ) && (__FPU_USED == 1U)) )) +#define __get_FPSCR __cmsis_iar_get_FPSR_not_active +#define __set_FPSCR __cmsis_iar_set_FPSR_not_active +#endif + +#ifdef __INTRINSICS_INCLUDED +#error intrinsics.h is already included previously! +#endif + +#include + +#if __IAR_M0_FAMILY +/* Avoid clash between intrinsics.h and arm_math.h when compiling for Cortex-M0. */ +#undef __CLZ +#undef __SSAT +#undef __USAT +#undef __RBIT +#undef __get_APSR + +__STATIC_INLINE uint8_t __CLZ(uint32_t data) +{ + if (data == 0U) + { + return 32U; + } + + uint32_t count = 0U; + uint32_t mask = 0x80000000U; + + while ((data & mask) == 0U) + { + count += 1U; + mask = mask >> 1U; + } + + return count; +} + +__STATIC_INLINE uint32_t __RBIT(uint32_t v) +{ + uint8_t sc = 31U; + uint32_t r = v; + + for (v >>= 1U; v; v >>= 1U) + { + r <<= 1U; + r |= v & 1U; + sc--; + } + + return (r << sc); +} + +__STATIC_INLINE uint32_t __get_APSR(void) +{ + uint32_t res; + __asm("MRS %0,APSR" : "=r" (res)); + return res; +} + +#endif + +#if (!((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \ + (defined (__FPU_USED ) && (__FPU_USED == 1U)) )) +#undef __get_FPSCR +#undef __set_FPSCR +#define __get_FPSCR() (0) +#define __set_FPSCR(VALUE) ((void)VALUE) +#endif + +#pragma diag_suppress=Pe940 +#pragma diag_suppress=Pe177 + +#define __enable_irq __enable_interrupt +#define __disable_irq __disable_interrupt +#define __NOP __no_operation + +#define __get_xPSR __get_PSR + +#if (!defined(__ARM_ARCH_6M__) || __ARM_ARCH_6M__==0) + +__IAR_FT uint32_t __LDREXW(uint32_t volatile* ptr) +{ + return __LDREX((unsigned long*)ptr); +} + +__IAR_FT uint32_t __STREXW(uint32_t value, uint32_t volatile* ptr) +{ + return __STREX(value, (unsigned long*)ptr); +} +#endif + + +/* __CORTEX_M is defined in core_cm0.h, core_cm3.h and core_cm4.h. */ +#if (__CORTEX_M >= 0x03) + +__IAR_FT uint32_t __RRX(uint32_t value) +{ + uint32_t result; + __ASM("RRX %0, %1" : "=r"(result) : "r" (value) : "cc"); + return (result); +} + +__IAR_FT void __set_BASEPRI_MAX(uint32_t value) +{ + __asm volatile("MSR BASEPRI_MAX,%0"::"r" (value)); +} + + +#define __enable_fault_irq __enable_fiq +#define __disable_fault_irq __disable_fiq + + +#endif /* (__CORTEX_M >= 0x03) */ + +__IAR_FT uint32_t __ROR(uint32_t op1, uint32_t op2) +{ + return (op1 >> op2) | (op1 << ((sizeof(op1) * 8) - op2)); +} + +#if ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \ + (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1)) ) + +__IAR_FT uint32_t __get_MSPLIM(void) +{ + uint32_t res; +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE ) || (__ARM_FEATURE_CMSE < 3))) + // without main extensions, the non-secure MSPLIM is RAZ/WI + res = 0U; +#else + __asm volatile("MRS %0,MSPLIM" : "=r" (res)); +#endif + return res; +} + +__IAR_FT void __set_MSPLIM(uint32_t value) +{ +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE ) || (__ARM_FEATURE_CMSE < 3))) + // without main extensions, the non-secure MSPLIM is RAZ/WI + (void)value; +#else + __asm volatile("MSR MSPLIM,%0" :: "r" (value)); +#endif +} + +__IAR_FT uint32_t __get_PSPLIM(void) +{ + uint32_t res; +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE ) || (__ARM_FEATURE_CMSE < 3))) + // without main extensions, the non-secure PSPLIM is RAZ/WI + res = 0U; +#else + __asm volatile("MRS %0,PSPLIM" : "=r" (res)); +#endif + return res; +} + +__IAR_FT void __set_PSPLIM(uint32_t value) +{ +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE ) || (__ARM_FEATURE_CMSE < 3))) + // without main extensions, the non-secure PSPLIM is RAZ/WI + (void)value; +#else + __asm volatile("MSR PSPLIM,%0" :: "r" (value)); +#endif +} + +__IAR_FT uint32_t __TZ_get_CONTROL_NS(void) +{ + uint32_t res; + __asm volatile("MRS %0,CONTROL_NS" : "=r" (res)); + return res; +} + +__IAR_FT void __TZ_set_CONTROL_NS(uint32_t value) +{ + __asm volatile("MSR CONTROL_NS,%0" :: "r" (value)); +} + +__IAR_FT uint32_t __TZ_get_PSP_NS(void) +{ + uint32_t res; + __asm volatile("MRS %0,PSP_NS" : "=r" (res)); + return res; +} + +__IAR_FT void __TZ_set_PSP_NS(uint32_t value) +{ + __asm volatile("MSR PSP_NS,%0" :: "r" (value)); +} + +__IAR_FT uint32_t __TZ_get_MSP_NS(void) +{ + uint32_t res; + __asm volatile("MRS %0,MSP_NS" : "=r" (res)); + return res; +} + +__IAR_FT void __TZ_set_MSP_NS(uint32_t value) +{ + __asm volatile("MSR MSP_NS,%0" :: "r" (value)); +} + +__IAR_FT uint32_t __TZ_get_SP_NS(void) +{ + uint32_t res; + __asm volatile("MRS %0,SP_NS" : "=r" (res)); + return res; +} +__IAR_FT void __TZ_set_SP_NS(uint32_t value) +{ + __asm volatile("MSR SP_NS,%0" :: "r" (value)); +} + +__IAR_FT uint32_t __TZ_get_PRIMASK_NS(void) +{ + uint32_t res; + __asm volatile("MRS %0,PRIMASK_NS" : "=r" (res)); + return res; +} + +__IAR_FT void __TZ_set_PRIMASK_NS(uint32_t value) +{ + __asm volatile("MSR PRIMASK_NS,%0" :: "r" (value)); +} + +__IAR_FT uint32_t __TZ_get_BASEPRI_NS(void) +{ + uint32_t res; + __asm volatile("MRS %0,BASEPRI_NS" : "=r" (res)); + return res; +} + +__IAR_FT void __TZ_set_BASEPRI_NS(uint32_t value) +{ + __asm volatile("MSR BASEPRI_NS,%0" :: "r" (value)); +} + +__IAR_FT uint32_t __TZ_get_FAULTMASK_NS(void) +{ + uint32_t res; + __asm volatile("MRS %0,FAULTMASK_NS" : "=r" (res)); + return res; +} + +__IAR_FT void __TZ_set_FAULTMASK_NS(uint32_t value) +{ + __asm volatile("MSR FAULTMASK_NS,%0" :: "r" (value)); +} + +__IAR_FT uint32_t __TZ_get_PSPLIM_NS(void) +{ + uint32_t res; +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE ) || (__ARM_FEATURE_CMSE < 3))) + // without main extensions, the non-secure PSPLIM is RAZ/WI + res = 0U; +#else + __asm volatile("MRS %0,PSPLIM_NS" : "=r" (res)); +#endif + return res; +} + +__IAR_FT void __TZ_set_PSPLIM_NS(uint32_t value) +{ +#if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \ + (!defined (__ARM_FEATURE_CMSE ) || (__ARM_FEATURE_CMSE < 3))) + // without main extensions, the non-secure PSPLIM is RAZ/WI + (void)value; +#else + __asm volatile("MSR PSPLIM_NS,%0" :: "r" (value)); +#endif +} + +__IAR_FT uint32_t __TZ_get_MSPLIM_NS(void) +{ + uint32_t res; + __asm volatile("MRS %0,MSPLIM_NS" : "=r" (res)); + return res; +} + +__IAR_FT void __TZ_set_MSPLIM_NS(uint32_t value) +{ + __asm volatile("MSR MSPLIM_NS,%0" :: "r" (value)); +} + +#endif /* __ARM_ARCH_8M_MAIN__ or __ARM_ARCH_8M_BASE__ */ + +#endif /* __ICCARM_INTRINSICS_VERSION__ == 2 */ + +#define __BKPT(value) __asm volatile ("BKPT %0" : : "i"(value)) + +#if __IAR_M0_FAMILY +__STATIC_INLINE int32_t __SSAT(int32_t val, uint32_t sat) +{ + if ((sat >= 1U) && (sat <= 32U)) + { + const int32_t max = (int32_t)((1U << (sat - 1U)) - 1U); + const int32_t min = -1 - max ; + + if (val > max) + { + return max; + } + else if (val < min) + { + return min; + } + } + + return val; +} + +__STATIC_INLINE uint32_t __USAT(int32_t val, uint32_t sat) +{ + if (sat <= 31U) + { + const uint32_t max = ((1U << sat) - 1U); + + if (val > (int32_t)max) + { + return max; + } + else if (val < 0) + { + return 0U; + } + } + + return (uint32_t)val; +} +#endif + +#if (__CORTEX_M >= 0x03) /* __CORTEX_M is defined in core_cm0.h, core_cm3.h and core_cm4.h. */ + +__IAR_FT uint8_t __LDRBT(volatile uint8_t* addr) +{ + uint32_t res; + __ASM("LDRBT %0, [%1]" : "=r" (res) : "r" (addr) : "memory"); + return ((uint8_t)res); +} + +__IAR_FT uint16_t __LDRHT(volatile uint16_t* addr) +{ + uint32_t res; + __ASM("LDRHT %0, [%1]" : "=r" (res) : "r" (addr) : "memory"); + return ((uint16_t)res); +} + +__IAR_FT uint32_t __LDRT(volatile uint32_t* addr) +{ + uint32_t res; + __ASM("LDRT %0, [%1]" : "=r" (res) : "r" (addr) : "memory"); + return res; +} + +__IAR_FT void __STRBT(uint8_t value, volatile uint8_t* addr) +{ + __ASM("STRBT %1, [%0]" : : "r" (addr), "r" ((uint32_t)value) : "memory"); +} + +__IAR_FT void __STRHT(uint16_t value, volatile uint16_t* addr) +{ + __ASM("STRHT %1, [%0]" : : "r" (addr), "r" ((uint32_t)value) : "memory"); +} + +__IAR_FT void __STRT(uint32_t value, volatile uint32_t* addr) +{ + __ASM("STRT %1, [%0]" : : "r" (addr), "r" (value) : "memory"); +} + +#endif /* (__CORTEX_M >= 0x03) */ + +#if ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \ + (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1)) ) + + +__IAR_FT uint8_t __LDAB(volatile uint8_t* ptr) +{ + uint32_t res; + __ASM volatile ("LDAB %0, [%1]" : "=r" (res) : "r" (ptr) : "memory"); + return ((uint8_t)res); +} + +__IAR_FT uint16_t __LDAH(volatile uint16_t* ptr) +{ + uint32_t res; + __ASM volatile ("LDAH %0, [%1]" : "=r" (res) : "r" (ptr) : "memory"); + return ((uint16_t)res); +} + +__IAR_FT uint32_t __LDA(volatile uint32_t* ptr) +{ + uint32_t res; + __ASM volatile ("LDA %0, [%1]" : "=r" (res) : "r" (ptr) : "memory"); + return res; +} + +__IAR_FT void __STLB(uint8_t value, volatile uint8_t* ptr) +{ + __ASM volatile ("STLB %1, [%0]" :: "r" (ptr), "r" (value) : "memory"); +} + +__IAR_FT void __STLH(uint16_t value, volatile uint16_t* ptr) +{ + __ASM volatile ("STLH %1, [%0]" :: "r" (ptr), "r" (value) : "memory"); +} + +__IAR_FT void __STL(uint32_t value, volatile uint32_t* ptr) +{ + __ASM volatile ("STL %1, [%0]" :: "r" (ptr), "r" (value) : "memory"); +} + +__IAR_FT uint8_t __LDAEXB(volatile uint8_t* ptr) +{ + uint32_t res; + __ASM volatile ("LDAEXB %0, [%1]" : "=r" (res) : "r" (ptr) : "memory"); + return ((uint8_t)res); +} + +__IAR_FT uint16_t __LDAEXH(volatile uint16_t* ptr) +{ + uint32_t res; + __ASM volatile ("LDAEXH %0, [%1]" : "=r" (res) : "r" (ptr) : "memory"); + return ((uint16_t)res); +} + +__IAR_FT uint32_t __LDAEX(volatile uint32_t* ptr) +{ + uint32_t res; + __ASM volatile ("LDAEX %0, [%1]" : "=r" (res) : "r" (ptr) : "memory"); + return res; +} + +__IAR_FT uint32_t __STLEXB(uint8_t value, volatile uint8_t* ptr) +{ + uint32_t res; + __ASM volatile ("STLEXB %0, %2, [%1]" : "=r" (res) : "r" (ptr), "r" (value) : "memory"); + return res; +} + +__IAR_FT uint32_t __STLEXH(uint16_t value, volatile uint16_t* ptr) +{ + uint32_t res; + __ASM volatile ("STLEXH %0, %2, [%1]" : "=r" (res) : "r" (ptr), "r" (value) : "memory"); + return res; +} + +__IAR_FT uint32_t __STLEX(uint32_t value, volatile uint32_t* ptr) +{ + uint32_t res; + __ASM volatile ("STLEX %0, %2, [%1]" : "=r" (res) : "r" (ptr), "r" (value) : "memory"); + return res; +} + +#endif /* __ARM_ARCH_8M_MAIN__ or __ARM_ARCH_8M_BASE__ */ + +#undef __IAR_FT +#undef __IAR_M0_FAMILY +#undef __ICCARM_V8 + +#pragma diag_default=Pe940 +#pragma diag_default=Pe177 + +#endif /* __CMSIS_ICCARM_H__ */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/cmsis_version.h b/EpsilonLights/Drivers/CMSIS/Include/cmsis_version.h new file mode 100644 index 00000000..3247abb9 --- /dev/null +++ b/EpsilonLights/Drivers/CMSIS/Include/cmsis_version.h @@ -0,0 +1,39 @@ +/**************************************************************************//** + * @file cmsis_version.h + * @brief CMSIS Core(M) Version definitions + * @version V5.0.2 + * @date 19. April 2017 + ******************************************************************************/ +/* + * Copyright (c) 2009-2017 ARM Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ + +#if defined ( __ICCARM__ ) +#pragma system_include /* treat file as system include file for MISRA check */ +#elif defined (__clang__) +#pragma clang system_header /* treat file as system include file */ +#endif + +#ifndef __CMSIS_VERSION_H +#define __CMSIS_VERSION_H + +/* CMSIS Version definitions */ +#define __CM_CMSIS_VERSION_MAIN ( 5U) /*!< [31:16] CMSIS Core(M) main version */ +#define __CM_CMSIS_VERSION_SUB ( 1U) /*!< [15:0] CMSIS Core(M) sub version */ +#define __CM_CMSIS_VERSION ((__CM_CMSIS_VERSION_MAIN << 16U) | \ + __CM_CMSIS_VERSION_SUB ) /*!< CMSIS Core(M) version number */ +#endif diff --git a/EpsilonLights/Drivers/CMSIS/Include/core_armv8mbl.h b/EpsilonLights/Drivers/CMSIS/Include/core_armv8mbl.h new file mode 100644 index 00000000..e967f8f4 --- /dev/null +++ b/EpsilonLights/Drivers/CMSIS/Include/core_armv8mbl.h @@ -0,0 +1,1920 @@ +/**************************************************************************//** + * @file core_armv8mbl.h + * @brief CMSIS Armv8-M Baseline Core Peripheral Access Layer Header File + * @version V5.0.7 + * @date 22. June 2018 + ******************************************************************************/ +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ + +#if defined ( __ICCARM__ ) +#pragma system_include /* treat file as system include file for MISRA check */ +#elif defined (__clang__) +#pragma clang system_header /* treat file as system include file */ +#endif + +#ifndef __CORE_ARMV8MBL_H_GENERIC +#define __CORE_ARMV8MBL_H_GENERIC + +#include + +#ifdef __cplusplus +extern "C" { +#endif + +/** + \page CMSIS_MISRA_Exceptions MISRA-C:2004 Compliance Exceptions + CMSIS violates the following MISRA-C:2004 rules: + + \li Required Rule 8.5, object/function definition in header file.
+ Function definitions in header files are used to allow 'inlining'. + + \li Required Rule 18.4, declaration of union type or object of union type: '{...}'.
+ Unions are used for effective representation of core registers. + + \li Advisory Rule 19.7, Function-like macro defined.
+ Function-like macros are used to allow more efficient code. + */ + + +/******************************************************************************* + * CMSIS definitions + ******************************************************************************/ +/** + \ingroup Cortex_ARMv8MBL + @{ + */ + +#include "cmsis_version.h" + +/* CMSIS definitions */ +#define __ARMv8MBL_CMSIS_VERSION_MAIN (__CM_CMSIS_VERSION_MAIN) /*!< \deprecated [31:16] CMSIS HAL main version */ +#define __ARMv8MBL_CMSIS_VERSION_SUB (__CM_CMSIS_VERSION_SUB) /*!< \deprecated [15:0] CMSIS HAL sub version */ +#define __ARMv8MBL_CMSIS_VERSION ((__ARMv8MBL_CMSIS_VERSION_MAIN << 16U) | \ + __ARMv8MBL_CMSIS_VERSION_SUB ) /*!< \deprecated CMSIS HAL version number */ + +#define __CORTEX_M ( 2U) /*!< Cortex-M Core */ + +/** __FPU_USED indicates whether an FPU is used or not. + This core does not support an FPU at all +*/ +#define __FPU_USED 0U + +#if defined ( __CC_ARM ) +#if defined __TARGET_FPU_VFP +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#if defined __ARM_PCS_VFP +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined ( __GNUC__ ) +#if defined (__VFP_FP__) && !defined(__SOFTFP__) +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined ( __ICCARM__ ) +#if defined __ARMVFP__ +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined ( __TI_ARM__ ) +#if defined __TI_VFP_SUPPORT__ +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined ( __TASKING__ ) +#if defined __FPU_VFP__ +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined ( __CSMC__ ) +#if ( __CSMC__ & 0x400U) +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#endif + +#include "cmsis_compiler.h" /* CMSIS compiler specific defines */ + + +#ifdef __cplusplus +} +#endif + +#endif /* __CORE_ARMV8MBL_H_GENERIC */ + +#ifndef __CMSIS_GENERIC + +#ifndef __CORE_ARMV8MBL_H_DEPENDANT +#define __CORE_ARMV8MBL_H_DEPENDANT + +#ifdef __cplusplus +extern "C" { +#endif + +/* check device defines and use defaults */ +#if defined __CHECK_DEVICE_DEFINES +#ifndef __ARMv8MBL_REV +#define __ARMv8MBL_REV 0x0000U +#warning "__ARMv8MBL_REV not defined in device header file; using default!" +#endif + +#ifndef __FPU_PRESENT +#define __FPU_PRESENT 0U +#warning "__FPU_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __MPU_PRESENT +#define __MPU_PRESENT 0U +#warning "__MPU_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __SAUREGION_PRESENT +#define __SAUREGION_PRESENT 0U +#warning "__SAUREGION_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __VTOR_PRESENT +#define __VTOR_PRESENT 0U +#warning "__VTOR_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __NVIC_PRIO_BITS +#define __NVIC_PRIO_BITS 2U +#warning "__NVIC_PRIO_BITS not defined in device header file; using default!" +#endif + +#ifndef __Vendor_SysTickConfig +#define __Vendor_SysTickConfig 0U +#warning "__Vendor_SysTickConfig not defined in device header file; using default!" +#endif + +#ifndef __ETM_PRESENT +#define __ETM_PRESENT 0U +#warning "__ETM_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __MTB_PRESENT +#define __MTB_PRESENT 0U +#warning "__MTB_PRESENT not defined in device header file; using default!" +#endif + +#endif + +/* IO definitions (access restrictions to peripheral registers) */ +/** + \defgroup CMSIS_glob_defs CMSIS Global Defines + + IO Type Qualifiers are used + \li to specify the access to peripheral variables. + \li for automatic generation of peripheral register debug information. +*/ +#ifdef __cplusplus +#define __I volatile /*!< Defines 'read only' permissions */ +#else +#define __I volatile const /*!< Defines 'read only' permissions */ +#endif +#define __O volatile /*!< Defines 'write only' permissions */ +#define __IO volatile /*!< Defines 'read / write' permissions */ + +/* following defines should be used for structure members */ +#define __IM volatile const /*! Defines 'read only' structure member permissions */ +#define __OM volatile /*! Defines 'write only' structure member permissions */ +#define __IOM volatile /*! Defines 'read / write' structure member permissions */ + +/*@} end of group ARMv8MBL */ + + + +/******************************************************************************* + * Register Abstraction + Core Register contain: + - Core Register + - Core NVIC Register + - Core SCB Register + - Core SysTick Register + - Core Debug Register + - Core MPU Register + - Core SAU Register + ******************************************************************************/ +/** + \defgroup CMSIS_core_register Defines and Type Definitions + \brief Type definitions and defines for Cortex-M processor based devices. +*/ + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_CORE Status and Control Registers + \brief Core Register type definitions. + @{ + */ + +/** + \brief Union type to access the Application Program Status Register (APSR). + */ +typedef union +{ + struct + { + uint32_t _reserved0: 28; /*!< bit: 0..27 Reserved */ + uint32_t V: 1; /*!< bit: 28 Overflow condition code flag */ + uint32_t C: 1; /*!< bit: 29 Carry condition code flag */ + uint32_t Z: 1; /*!< bit: 30 Zero condition code flag */ + uint32_t N: 1; /*!< bit: 31 Negative condition code flag */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} APSR_Type; + +/* APSR Register Definitions */ +#define APSR_N_Pos 31U /*!< APSR: N Position */ +#define APSR_N_Msk (1UL << APSR_N_Pos) /*!< APSR: N Mask */ + +#define APSR_Z_Pos 30U /*!< APSR: Z Position */ +#define APSR_Z_Msk (1UL << APSR_Z_Pos) /*!< APSR: Z Mask */ + +#define APSR_C_Pos 29U /*!< APSR: C Position */ +#define APSR_C_Msk (1UL << APSR_C_Pos) /*!< APSR: C Mask */ + +#define APSR_V_Pos 28U /*!< APSR: V Position */ +#define APSR_V_Msk (1UL << APSR_V_Pos) /*!< APSR: V Mask */ + + +/** + \brief Union type to access the Interrupt Program Status Register (IPSR). + */ +typedef union +{ + struct + { + uint32_t ISR: 9; /*!< bit: 0.. 8 Exception number */ + uint32_t _reserved0: 23; /*!< bit: 9..31 Reserved */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} IPSR_Type; + +/* IPSR Register Definitions */ +#define IPSR_ISR_Pos 0U /*!< IPSR: ISR Position */ +#define IPSR_ISR_Msk (0x1FFUL /*<< IPSR_ISR_Pos*/) /*!< IPSR: ISR Mask */ + + +/** + \brief Union type to access the Special-Purpose Program Status Registers (xPSR). + */ +typedef union +{ + struct + { + uint32_t ISR: 9; /*!< bit: 0.. 8 Exception number */ + uint32_t _reserved0: 15; /*!< bit: 9..23 Reserved */ + uint32_t T: 1; /*!< bit: 24 Thumb bit (read 0) */ + uint32_t _reserved1: 3; /*!< bit: 25..27 Reserved */ + uint32_t V: 1; /*!< bit: 28 Overflow condition code flag */ + uint32_t C: 1; /*!< bit: 29 Carry condition code flag */ + uint32_t Z: 1; /*!< bit: 30 Zero condition code flag */ + uint32_t N: 1; /*!< bit: 31 Negative condition code flag */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} xPSR_Type; + +/* xPSR Register Definitions */ +#define xPSR_N_Pos 31U /*!< xPSR: N Position */ +#define xPSR_N_Msk (1UL << xPSR_N_Pos) /*!< xPSR: N Mask */ + +#define xPSR_Z_Pos 30U /*!< xPSR: Z Position */ +#define xPSR_Z_Msk (1UL << xPSR_Z_Pos) /*!< xPSR: Z Mask */ + +#define xPSR_C_Pos 29U /*!< xPSR: C Position */ +#define xPSR_C_Msk (1UL << xPSR_C_Pos) /*!< xPSR: C Mask */ + +#define xPSR_V_Pos 28U /*!< xPSR: V Position */ +#define xPSR_V_Msk (1UL << xPSR_V_Pos) /*!< xPSR: V Mask */ + +#define xPSR_T_Pos 24U /*!< xPSR: T Position */ +#define xPSR_T_Msk (1UL << xPSR_T_Pos) /*!< xPSR: T Mask */ + +#define xPSR_ISR_Pos 0U /*!< xPSR: ISR Position */ +#define xPSR_ISR_Msk (0x1FFUL /*<< xPSR_ISR_Pos*/) /*!< xPSR: ISR Mask */ + + +/** + \brief Union type to access the Control Registers (CONTROL). + */ +typedef union +{ + struct + { + uint32_t nPRIV: 1; /*!< bit: 0 Execution privilege in Thread mode */ + uint32_t SPSEL: 1; /*!< bit: 1 Stack-pointer select */ + uint32_t _reserved1: 30; /*!< bit: 2..31 Reserved */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} CONTROL_Type; + +/* CONTROL Register Definitions */ +#define CONTROL_SPSEL_Pos 1U /*!< CONTROL: SPSEL Position */ +#define CONTROL_SPSEL_Msk (1UL << CONTROL_SPSEL_Pos) /*!< CONTROL: SPSEL Mask */ + +#define CONTROL_nPRIV_Pos 0U /*!< CONTROL: nPRIV Position */ +#define CONTROL_nPRIV_Msk (1UL /*<< CONTROL_nPRIV_Pos*/) /*!< CONTROL: nPRIV Mask */ + +/*@} end of group CMSIS_CORE */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_NVIC Nested Vectored Interrupt Controller (NVIC) + \brief Type definitions for the NVIC Registers + @{ + */ + +/** + \brief Structure type to access the Nested Vectored Interrupt Controller (NVIC). + */ +typedef struct +{ + __IOM uint32_t ISER[16U]; /*!< Offset: 0x000 (R/W) Interrupt Set Enable Register */ + uint32_t RESERVED0[16U]; + __IOM uint32_t ICER[16U]; /*!< Offset: 0x080 (R/W) Interrupt Clear Enable Register */ + uint32_t RSERVED1[16U]; + __IOM uint32_t ISPR[16U]; /*!< Offset: 0x100 (R/W) Interrupt Set Pending Register */ + uint32_t RESERVED2[16U]; + __IOM uint32_t ICPR[16U]; /*!< Offset: 0x180 (R/W) Interrupt Clear Pending Register */ + uint32_t RESERVED3[16U]; + __IOM uint32_t IABR[16U]; /*!< Offset: 0x200 (R/W) Interrupt Active bit Register */ + uint32_t RESERVED4[16U]; + __IOM uint32_t ITNS[16U]; /*!< Offset: 0x280 (R/W) Interrupt Non-Secure State Register */ + uint32_t RESERVED5[16U]; + __IOM uint32_t IPR[124U]; /*!< Offset: 0x300 (R/W) Interrupt Priority Register */ +} NVIC_Type; + +/*@} end of group CMSIS_NVIC */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SCB System Control Block (SCB) + \brief Type definitions for the System Control Block Registers + @{ + */ + +/** + \brief Structure type to access the System Control Block (SCB). + */ +typedef struct +{ + __IM uint32_t CPUID; /*!< Offset: 0x000 (R/ ) CPUID Base Register */ + __IOM uint32_t ICSR; /*!< Offset: 0x004 (R/W) Interrupt Control and State Register */ +#if defined (__VTOR_PRESENT) && (__VTOR_PRESENT == 1U) + __IOM uint32_t VTOR; /*!< Offset: 0x008 (R/W) Vector Table Offset Register */ +#else + uint32_t RESERVED0; +#endif + __IOM uint32_t AIRCR; /*!< Offset: 0x00C (R/W) Application Interrupt and Reset Control Register */ + __IOM uint32_t SCR; /*!< Offset: 0x010 (R/W) System Control Register */ + __IOM uint32_t CCR; /*!< Offset: 0x014 (R/W) Configuration Control Register */ + uint32_t RESERVED1; + __IOM uint32_t SHPR[2U]; /*!< Offset: 0x01C (R/W) System Handlers Priority Registers. [0] is RESERVED */ + __IOM uint32_t SHCSR; /*!< Offset: 0x024 (R/W) System Handler Control and State Register */ +} SCB_Type; + +/* SCB CPUID Register Definitions */ +#define SCB_CPUID_IMPLEMENTER_Pos 24U /*!< SCB CPUID: IMPLEMENTER Position */ +#define SCB_CPUID_IMPLEMENTER_Msk (0xFFUL << SCB_CPUID_IMPLEMENTER_Pos) /*!< SCB CPUID: IMPLEMENTER Mask */ + +#define SCB_CPUID_VARIANT_Pos 20U /*!< SCB CPUID: VARIANT Position */ +#define SCB_CPUID_VARIANT_Msk (0xFUL << SCB_CPUID_VARIANT_Pos) /*!< SCB CPUID: VARIANT Mask */ + +#define SCB_CPUID_ARCHITECTURE_Pos 16U /*!< SCB CPUID: ARCHITECTURE Position */ +#define SCB_CPUID_ARCHITECTURE_Msk (0xFUL << SCB_CPUID_ARCHITECTURE_Pos) /*!< SCB CPUID: ARCHITECTURE Mask */ + +#define SCB_CPUID_PARTNO_Pos 4U /*!< SCB CPUID: PARTNO Position */ +#define SCB_CPUID_PARTNO_Msk (0xFFFUL << SCB_CPUID_PARTNO_Pos) /*!< SCB CPUID: PARTNO Mask */ + +#define SCB_CPUID_REVISION_Pos 0U /*!< SCB CPUID: REVISION Position */ +#define SCB_CPUID_REVISION_Msk (0xFUL /*<< SCB_CPUID_REVISION_Pos*/) /*!< SCB CPUID: REVISION Mask */ + +/* SCB Interrupt Control State Register Definitions */ +#define SCB_ICSR_PENDNMISET_Pos 31U /*!< SCB ICSR: PENDNMISET Position */ +#define SCB_ICSR_PENDNMISET_Msk (1UL << SCB_ICSR_PENDNMISET_Pos) /*!< SCB ICSR: PENDNMISET Mask */ + +#define SCB_ICSR_NMIPENDSET_Pos SCB_ICSR_PENDNMISET_Pos /*!< SCB ICSR: NMIPENDSET Position, backward compatibility */ +#define SCB_ICSR_NMIPENDSET_Msk SCB_ICSR_PENDNMISET_Msk /*!< SCB ICSR: NMIPENDSET Mask, backward compatibility */ + +#define SCB_ICSR_PENDNMICLR_Pos 30U /*!< SCB ICSR: PENDNMICLR Position */ +#define SCB_ICSR_PENDNMICLR_Msk (1UL << SCB_ICSR_PENDNMICLR_Pos) /*!< SCB ICSR: PENDNMICLR Mask */ + +#define SCB_ICSR_PENDSVSET_Pos 28U /*!< SCB ICSR: PENDSVSET Position */ +#define SCB_ICSR_PENDSVSET_Msk (1UL << SCB_ICSR_PENDSVSET_Pos) /*!< SCB ICSR: PENDSVSET Mask */ + +#define SCB_ICSR_PENDSVCLR_Pos 27U /*!< SCB ICSR: PENDSVCLR Position */ +#define SCB_ICSR_PENDSVCLR_Msk (1UL << SCB_ICSR_PENDSVCLR_Pos) /*!< SCB ICSR: PENDSVCLR Mask */ + +#define SCB_ICSR_PENDSTSET_Pos 26U /*!< SCB ICSR: PENDSTSET Position */ +#define SCB_ICSR_PENDSTSET_Msk (1UL << SCB_ICSR_PENDSTSET_Pos) /*!< SCB ICSR: PENDSTSET Mask */ + +#define SCB_ICSR_PENDSTCLR_Pos 25U /*!< SCB ICSR: PENDSTCLR Position */ +#define SCB_ICSR_PENDSTCLR_Msk (1UL << SCB_ICSR_PENDSTCLR_Pos) /*!< SCB ICSR: PENDSTCLR Mask */ + +#define SCB_ICSR_STTNS_Pos 24U /*!< SCB ICSR: STTNS Position (Security Extension) */ +#define SCB_ICSR_STTNS_Msk (1UL << SCB_ICSR_STTNS_Pos) /*!< SCB ICSR: STTNS Mask (Security Extension) */ + +#define SCB_ICSR_ISRPREEMPT_Pos 23U /*!< SCB ICSR: ISRPREEMPT Position */ +#define SCB_ICSR_ISRPREEMPT_Msk (1UL << SCB_ICSR_ISRPREEMPT_Pos) /*!< SCB ICSR: ISRPREEMPT Mask */ + +#define SCB_ICSR_ISRPENDING_Pos 22U /*!< SCB ICSR: ISRPENDING Position */ +#define SCB_ICSR_ISRPENDING_Msk (1UL << SCB_ICSR_ISRPENDING_Pos) /*!< SCB ICSR: ISRPENDING Mask */ + +#define SCB_ICSR_VECTPENDING_Pos 12U /*!< SCB ICSR: VECTPENDING Position */ +#define SCB_ICSR_VECTPENDING_Msk (0x1FFUL << SCB_ICSR_VECTPENDING_Pos) /*!< SCB ICSR: VECTPENDING Mask */ + +#define SCB_ICSR_RETTOBASE_Pos 11U /*!< SCB ICSR: RETTOBASE Position */ +#define SCB_ICSR_RETTOBASE_Msk (1UL << SCB_ICSR_RETTOBASE_Pos) /*!< SCB ICSR: RETTOBASE Mask */ + +#define SCB_ICSR_VECTACTIVE_Pos 0U /*!< SCB ICSR: VECTACTIVE Position */ +#define SCB_ICSR_VECTACTIVE_Msk (0x1FFUL /*<< SCB_ICSR_VECTACTIVE_Pos*/) /*!< SCB ICSR: VECTACTIVE Mask */ + +#if defined (__VTOR_PRESENT) && (__VTOR_PRESENT == 1U) +/* SCB Vector Table Offset Register Definitions */ +#define SCB_VTOR_TBLOFF_Pos 7U /*!< SCB VTOR: TBLOFF Position */ +#define SCB_VTOR_TBLOFF_Msk (0x1FFFFFFUL << SCB_VTOR_TBLOFF_Pos) /*!< SCB VTOR: TBLOFF Mask */ +#endif + +/* SCB Application Interrupt and Reset Control Register Definitions */ +#define SCB_AIRCR_VECTKEY_Pos 16U /*!< SCB AIRCR: VECTKEY Position */ +#define SCB_AIRCR_VECTKEY_Msk (0xFFFFUL << SCB_AIRCR_VECTKEY_Pos) /*!< SCB AIRCR: VECTKEY Mask */ + +#define SCB_AIRCR_VECTKEYSTAT_Pos 16U /*!< SCB AIRCR: VECTKEYSTAT Position */ +#define SCB_AIRCR_VECTKEYSTAT_Msk (0xFFFFUL << SCB_AIRCR_VECTKEYSTAT_Pos) /*!< SCB AIRCR: VECTKEYSTAT Mask */ + +#define SCB_AIRCR_ENDIANESS_Pos 15U /*!< SCB AIRCR: ENDIANESS Position */ +#define SCB_AIRCR_ENDIANESS_Msk (1UL << SCB_AIRCR_ENDIANESS_Pos) /*!< SCB AIRCR: ENDIANESS Mask */ + +#define SCB_AIRCR_PRIS_Pos 14U /*!< SCB AIRCR: PRIS Position */ +#define SCB_AIRCR_PRIS_Msk (1UL << SCB_AIRCR_PRIS_Pos) /*!< SCB AIRCR: PRIS Mask */ + +#define SCB_AIRCR_BFHFNMINS_Pos 13U /*!< SCB AIRCR: BFHFNMINS Position */ +#define SCB_AIRCR_BFHFNMINS_Msk (1UL << SCB_AIRCR_BFHFNMINS_Pos) /*!< SCB AIRCR: BFHFNMINS Mask */ + +#define SCB_AIRCR_SYSRESETREQS_Pos 3U /*!< SCB AIRCR: SYSRESETREQS Position */ +#define SCB_AIRCR_SYSRESETREQS_Msk (1UL << SCB_AIRCR_SYSRESETREQS_Pos) /*!< SCB AIRCR: SYSRESETREQS Mask */ + +#define SCB_AIRCR_SYSRESETREQ_Pos 2U /*!< SCB AIRCR: SYSRESETREQ Position */ +#define SCB_AIRCR_SYSRESETREQ_Msk (1UL << SCB_AIRCR_SYSRESETREQ_Pos) /*!< SCB AIRCR: SYSRESETREQ Mask */ + +#define SCB_AIRCR_VECTCLRACTIVE_Pos 1U /*!< SCB AIRCR: VECTCLRACTIVE Position */ +#define SCB_AIRCR_VECTCLRACTIVE_Msk (1UL << SCB_AIRCR_VECTCLRACTIVE_Pos) /*!< SCB AIRCR: VECTCLRACTIVE Mask */ + +/* SCB System Control Register Definitions */ +#define SCB_SCR_SEVONPEND_Pos 4U /*!< SCB SCR: SEVONPEND Position */ +#define SCB_SCR_SEVONPEND_Msk (1UL << SCB_SCR_SEVONPEND_Pos) /*!< SCB SCR: SEVONPEND Mask */ + +#define SCB_SCR_SLEEPDEEPS_Pos 3U /*!< SCB SCR: SLEEPDEEPS Position */ +#define SCB_SCR_SLEEPDEEPS_Msk (1UL << SCB_SCR_SLEEPDEEPS_Pos) /*!< SCB SCR: SLEEPDEEPS Mask */ + +#define SCB_SCR_SLEEPDEEP_Pos 2U /*!< SCB SCR: SLEEPDEEP Position */ +#define SCB_SCR_SLEEPDEEP_Msk (1UL << SCB_SCR_SLEEPDEEP_Pos) /*!< SCB SCR: SLEEPDEEP Mask */ + +#define SCB_SCR_SLEEPONEXIT_Pos 1U /*!< SCB SCR: SLEEPONEXIT Position */ +#define SCB_SCR_SLEEPONEXIT_Msk (1UL << SCB_SCR_SLEEPONEXIT_Pos) /*!< SCB SCR: SLEEPONEXIT Mask */ + +/* SCB Configuration Control Register Definitions */ +#define SCB_CCR_BP_Pos 18U /*!< SCB CCR: BP Position */ +#define SCB_CCR_BP_Msk (1UL << SCB_CCR_BP_Pos) /*!< SCB CCR: BP Mask */ + +#define SCB_CCR_IC_Pos 17U /*!< SCB CCR: IC Position */ +#define SCB_CCR_IC_Msk (1UL << SCB_CCR_IC_Pos) /*!< SCB CCR: IC Mask */ + +#define SCB_CCR_DC_Pos 16U /*!< SCB CCR: DC Position */ +#define SCB_CCR_DC_Msk (1UL << SCB_CCR_DC_Pos) /*!< SCB CCR: DC Mask */ + +#define SCB_CCR_STKOFHFNMIGN_Pos 10U /*!< SCB CCR: STKOFHFNMIGN Position */ +#define SCB_CCR_STKOFHFNMIGN_Msk (1UL << SCB_CCR_STKOFHFNMIGN_Pos) /*!< SCB CCR: STKOFHFNMIGN Mask */ + +#define SCB_CCR_BFHFNMIGN_Pos 8U /*!< SCB CCR: BFHFNMIGN Position */ +#define SCB_CCR_BFHFNMIGN_Msk (1UL << SCB_CCR_BFHFNMIGN_Pos) /*!< SCB CCR: BFHFNMIGN Mask */ + +#define SCB_CCR_DIV_0_TRP_Pos 4U /*!< SCB CCR: DIV_0_TRP Position */ +#define SCB_CCR_DIV_0_TRP_Msk (1UL << SCB_CCR_DIV_0_TRP_Pos) /*!< SCB CCR: DIV_0_TRP Mask */ + +#define SCB_CCR_UNALIGN_TRP_Pos 3U /*!< SCB CCR: UNALIGN_TRP Position */ +#define SCB_CCR_UNALIGN_TRP_Msk (1UL << SCB_CCR_UNALIGN_TRP_Pos) /*!< SCB CCR: UNALIGN_TRP Mask */ + +#define SCB_CCR_USERSETMPEND_Pos 1U /*!< SCB CCR: USERSETMPEND Position */ +#define SCB_CCR_USERSETMPEND_Msk (1UL << SCB_CCR_USERSETMPEND_Pos) /*!< SCB CCR: USERSETMPEND Mask */ + +/* SCB System Handler Control and State Register Definitions */ +#define SCB_SHCSR_HARDFAULTPENDED_Pos 21U /*!< SCB SHCSR: HARDFAULTPENDED Position */ +#define SCB_SHCSR_HARDFAULTPENDED_Msk (1UL << SCB_SHCSR_HARDFAULTPENDED_Pos) /*!< SCB SHCSR: HARDFAULTPENDED Mask */ + +#define SCB_SHCSR_SVCALLPENDED_Pos 15U /*!< SCB SHCSR: SVCALLPENDED Position */ +#define SCB_SHCSR_SVCALLPENDED_Msk (1UL << SCB_SHCSR_SVCALLPENDED_Pos) /*!< SCB SHCSR: SVCALLPENDED Mask */ + +#define SCB_SHCSR_SYSTICKACT_Pos 11U /*!< SCB SHCSR: SYSTICKACT Position */ +#define SCB_SHCSR_SYSTICKACT_Msk (1UL << SCB_SHCSR_SYSTICKACT_Pos) /*!< SCB SHCSR: SYSTICKACT Mask */ + +#define SCB_SHCSR_PENDSVACT_Pos 10U /*!< SCB SHCSR: PENDSVACT Position */ +#define SCB_SHCSR_PENDSVACT_Msk (1UL << SCB_SHCSR_PENDSVACT_Pos) /*!< SCB SHCSR: PENDSVACT Mask */ + +#define SCB_SHCSR_SVCALLACT_Pos 7U /*!< SCB SHCSR: SVCALLACT Position */ +#define SCB_SHCSR_SVCALLACT_Msk (1UL << SCB_SHCSR_SVCALLACT_Pos) /*!< SCB SHCSR: SVCALLACT Mask */ + +#define SCB_SHCSR_NMIACT_Pos 5U /*!< SCB SHCSR: NMIACT Position */ +#define SCB_SHCSR_NMIACT_Msk (1UL << SCB_SHCSR_NMIACT_Pos) /*!< SCB SHCSR: NMIACT Mask */ + +#define SCB_SHCSR_HARDFAULTACT_Pos 2U /*!< SCB SHCSR: HARDFAULTACT Position */ +#define SCB_SHCSR_HARDFAULTACT_Msk (1UL << SCB_SHCSR_HARDFAULTACT_Pos) /*!< SCB SHCSR: HARDFAULTACT Mask */ + +/*@} end of group CMSIS_SCB */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SysTick System Tick Timer (SysTick) + \brief Type definitions for the System Timer Registers. + @{ + */ + +/** + \brief Structure type to access the System Timer (SysTick). + */ +typedef struct +{ + __IOM uint32_t CTRL; /*!< Offset: 0x000 (R/W) SysTick Control and Status Register */ + __IOM uint32_t LOAD; /*!< Offset: 0x004 (R/W) SysTick Reload Value Register */ + __IOM uint32_t VAL; /*!< Offset: 0x008 (R/W) SysTick Current Value Register */ + __IM uint32_t CALIB; /*!< Offset: 0x00C (R/ ) SysTick Calibration Register */ +} SysTick_Type; + +/* SysTick Control / Status Register Definitions */ +#define SysTick_CTRL_COUNTFLAG_Pos 16U /*!< SysTick CTRL: COUNTFLAG Position */ +#define SysTick_CTRL_COUNTFLAG_Msk (1UL << SysTick_CTRL_COUNTFLAG_Pos) /*!< SysTick CTRL: COUNTFLAG Mask */ + +#define SysTick_CTRL_CLKSOURCE_Pos 2U /*!< SysTick CTRL: CLKSOURCE Position */ +#define SysTick_CTRL_CLKSOURCE_Msk (1UL << SysTick_CTRL_CLKSOURCE_Pos) /*!< SysTick CTRL: CLKSOURCE Mask */ + +#define SysTick_CTRL_TICKINT_Pos 1U /*!< SysTick CTRL: TICKINT Position */ +#define SysTick_CTRL_TICKINT_Msk (1UL << SysTick_CTRL_TICKINT_Pos) /*!< SysTick CTRL: TICKINT Mask */ + +#define SysTick_CTRL_ENABLE_Pos 0U /*!< SysTick CTRL: ENABLE Position */ +#define SysTick_CTRL_ENABLE_Msk (1UL /*<< SysTick_CTRL_ENABLE_Pos*/) /*!< SysTick CTRL: ENABLE Mask */ + +/* SysTick Reload Register Definitions */ +#define SysTick_LOAD_RELOAD_Pos 0U /*!< SysTick LOAD: RELOAD Position */ +#define SysTick_LOAD_RELOAD_Msk (0xFFFFFFUL /*<< SysTick_LOAD_RELOAD_Pos*/) /*!< SysTick LOAD: RELOAD Mask */ + +/* SysTick Current Register Definitions */ +#define SysTick_VAL_CURRENT_Pos 0U /*!< SysTick VAL: CURRENT Position */ +#define SysTick_VAL_CURRENT_Msk (0xFFFFFFUL /*<< SysTick_VAL_CURRENT_Pos*/) /*!< SysTick VAL: CURRENT Mask */ + +/* SysTick Calibration Register Definitions */ +#define SysTick_CALIB_NOREF_Pos 31U /*!< SysTick CALIB: NOREF Position */ +#define SysTick_CALIB_NOREF_Msk (1UL << SysTick_CALIB_NOREF_Pos) /*!< SysTick CALIB: NOREF Mask */ + +#define SysTick_CALIB_SKEW_Pos 30U /*!< SysTick CALIB: SKEW Position */ +#define SysTick_CALIB_SKEW_Msk (1UL << SysTick_CALIB_SKEW_Pos) /*!< SysTick CALIB: SKEW Mask */ + +#define SysTick_CALIB_TENMS_Pos 0U /*!< SysTick CALIB: TENMS Position */ +#define SysTick_CALIB_TENMS_Msk (0xFFFFFFUL /*<< SysTick_CALIB_TENMS_Pos*/) /*!< SysTick CALIB: TENMS Mask */ + +/*@} end of group CMSIS_SysTick */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_DWT Data Watchpoint and Trace (DWT) + \brief Type definitions for the Data Watchpoint and Trace (DWT) + @{ + */ + +/** + \brief Structure type to access the Data Watchpoint and Trace Register (DWT). + */ +typedef struct +{ + __IOM uint32_t CTRL; /*!< Offset: 0x000 (R/W) Control Register */ + uint32_t RESERVED0[6U]; + __IM uint32_t PCSR; /*!< Offset: 0x01C (R/ ) Program Counter Sample Register */ + __IOM uint32_t COMP0; /*!< Offset: 0x020 (R/W) Comparator Register 0 */ + uint32_t RESERVED1[1U]; + __IOM uint32_t FUNCTION0; /*!< Offset: 0x028 (R/W) Function Register 0 */ + uint32_t RESERVED2[1U]; + __IOM uint32_t COMP1; /*!< Offset: 0x030 (R/W) Comparator Register 1 */ + uint32_t RESERVED3[1U]; + __IOM uint32_t FUNCTION1; /*!< Offset: 0x038 (R/W) Function Register 1 */ + uint32_t RESERVED4[1U]; + __IOM uint32_t COMP2; /*!< Offset: 0x040 (R/W) Comparator Register 2 */ + uint32_t RESERVED5[1U]; + __IOM uint32_t FUNCTION2; /*!< Offset: 0x048 (R/W) Function Register 2 */ + uint32_t RESERVED6[1U]; + __IOM uint32_t COMP3; /*!< Offset: 0x050 (R/W) Comparator Register 3 */ + uint32_t RESERVED7[1U]; + __IOM uint32_t FUNCTION3; /*!< Offset: 0x058 (R/W) Function Register 3 */ + uint32_t RESERVED8[1U]; + __IOM uint32_t COMP4; /*!< Offset: 0x060 (R/W) Comparator Register 4 */ + uint32_t RESERVED9[1U]; + __IOM uint32_t FUNCTION4; /*!< Offset: 0x068 (R/W) Function Register 4 */ + uint32_t RESERVED10[1U]; + __IOM uint32_t COMP5; /*!< Offset: 0x070 (R/W) Comparator Register 5 */ + uint32_t RESERVED11[1U]; + __IOM uint32_t FUNCTION5; /*!< Offset: 0x078 (R/W) Function Register 5 */ + uint32_t RESERVED12[1U]; + __IOM uint32_t COMP6; /*!< Offset: 0x080 (R/W) Comparator Register 6 */ + uint32_t RESERVED13[1U]; + __IOM uint32_t FUNCTION6; /*!< Offset: 0x088 (R/W) Function Register 6 */ + uint32_t RESERVED14[1U]; + __IOM uint32_t COMP7; /*!< Offset: 0x090 (R/W) Comparator Register 7 */ + uint32_t RESERVED15[1U]; + __IOM uint32_t FUNCTION7; /*!< Offset: 0x098 (R/W) Function Register 7 */ + uint32_t RESERVED16[1U]; + __IOM uint32_t COMP8; /*!< Offset: 0x0A0 (R/W) Comparator Register 8 */ + uint32_t RESERVED17[1U]; + __IOM uint32_t FUNCTION8; /*!< Offset: 0x0A8 (R/W) Function Register 8 */ + uint32_t RESERVED18[1U]; + __IOM uint32_t COMP9; /*!< Offset: 0x0B0 (R/W) Comparator Register 9 */ + uint32_t RESERVED19[1U]; + __IOM uint32_t FUNCTION9; /*!< Offset: 0x0B8 (R/W) Function Register 9 */ + uint32_t RESERVED20[1U]; + __IOM uint32_t COMP10; /*!< Offset: 0x0C0 (R/W) Comparator Register 10 */ + uint32_t RESERVED21[1U]; + __IOM uint32_t FUNCTION10; /*!< Offset: 0x0C8 (R/W) Function Register 10 */ + uint32_t RESERVED22[1U]; + __IOM uint32_t COMP11; /*!< Offset: 0x0D0 (R/W) Comparator Register 11 */ + uint32_t RESERVED23[1U]; + __IOM uint32_t FUNCTION11; /*!< Offset: 0x0D8 (R/W) Function Register 11 */ + uint32_t RESERVED24[1U]; + __IOM uint32_t COMP12; /*!< Offset: 0x0E0 (R/W) Comparator Register 12 */ + uint32_t RESERVED25[1U]; + __IOM uint32_t FUNCTION12; /*!< Offset: 0x0E8 (R/W) Function Register 12 */ + uint32_t RESERVED26[1U]; + __IOM uint32_t COMP13; /*!< Offset: 0x0F0 (R/W) Comparator Register 13 */ + uint32_t RESERVED27[1U]; + __IOM uint32_t FUNCTION13; /*!< Offset: 0x0F8 (R/W) Function Register 13 */ + uint32_t RESERVED28[1U]; + __IOM uint32_t COMP14; /*!< Offset: 0x100 (R/W) Comparator Register 14 */ + uint32_t RESERVED29[1U]; + __IOM uint32_t FUNCTION14; /*!< Offset: 0x108 (R/W) Function Register 14 */ + uint32_t RESERVED30[1U]; + __IOM uint32_t COMP15; /*!< Offset: 0x110 (R/W) Comparator Register 15 */ + uint32_t RESERVED31[1U]; + __IOM uint32_t FUNCTION15; /*!< Offset: 0x118 (R/W) Function Register 15 */ +} DWT_Type; + +/* DWT Control Register Definitions */ +#define DWT_CTRL_NUMCOMP_Pos 28U /*!< DWT CTRL: NUMCOMP Position */ +#define DWT_CTRL_NUMCOMP_Msk (0xFUL << DWT_CTRL_NUMCOMP_Pos) /*!< DWT CTRL: NUMCOMP Mask */ + +#define DWT_CTRL_NOTRCPKT_Pos 27U /*!< DWT CTRL: NOTRCPKT Position */ +#define DWT_CTRL_NOTRCPKT_Msk (0x1UL << DWT_CTRL_NOTRCPKT_Pos) /*!< DWT CTRL: NOTRCPKT Mask */ + +#define DWT_CTRL_NOEXTTRIG_Pos 26U /*!< DWT CTRL: NOEXTTRIG Position */ +#define DWT_CTRL_NOEXTTRIG_Msk (0x1UL << DWT_CTRL_NOEXTTRIG_Pos) /*!< DWT CTRL: NOEXTTRIG Mask */ + +#define DWT_CTRL_NOCYCCNT_Pos 25U /*!< DWT CTRL: NOCYCCNT Position */ +#define DWT_CTRL_NOCYCCNT_Msk (0x1UL << DWT_CTRL_NOCYCCNT_Pos) /*!< DWT CTRL: NOCYCCNT Mask */ + +#define DWT_CTRL_NOPRFCNT_Pos 24U /*!< DWT CTRL: NOPRFCNT Position */ +#define DWT_CTRL_NOPRFCNT_Msk (0x1UL << DWT_CTRL_NOPRFCNT_Pos) /*!< DWT CTRL: NOPRFCNT Mask */ + +/* DWT Comparator Function Register Definitions */ +#define DWT_FUNCTION_ID_Pos 27U /*!< DWT FUNCTION: ID Position */ +#define DWT_FUNCTION_ID_Msk (0x1FUL << DWT_FUNCTION_ID_Pos) /*!< DWT FUNCTION: ID Mask */ + +#define DWT_FUNCTION_MATCHED_Pos 24U /*!< DWT FUNCTION: MATCHED Position */ +#define DWT_FUNCTION_MATCHED_Msk (0x1UL << DWT_FUNCTION_MATCHED_Pos) /*!< DWT FUNCTION: MATCHED Mask */ + +#define DWT_FUNCTION_DATAVSIZE_Pos 10U /*!< DWT FUNCTION: DATAVSIZE Position */ +#define DWT_FUNCTION_DATAVSIZE_Msk (0x3UL << DWT_FUNCTION_DATAVSIZE_Pos) /*!< DWT FUNCTION: DATAVSIZE Mask */ + +#define DWT_FUNCTION_ACTION_Pos 4U /*!< DWT FUNCTION: ACTION Position */ +#define DWT_FUNCTION_ACTION_Msk (0x3UL << DWT_FUNCTION_ACTION_Pos) /*!< DWT FUNCTION: ACTION Mask */ + +#define DWT_FUNCTION_MATCH_Pos 0U /*!< DWT FUNCTION: MATCH Position */ +#define DWT_FUNCTION_MATCH_Msk (0xFUL /*<< DWT_FUNCTION_MATCH_Pos*/) /*!< DWT FUNCTION: MATCH Mask */ + +/*@}*/ /* end of group CMSIS_DWT */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_TPI Trace Port Interface (TPI) + \brief Type definitions for the Trace Port Interface (TPI) + @{ + */ + +/** + \brief Structure type to access the Trace Port Interface Register (TPI). + */ +typedef struct +{ + __IM uint32_t SSPSR; /*!< Offset: 0x000 (R/ ) Supported Parallel Port Sizes Register */ + __IOM uint32_t CSPSR; /*!< Offset: 0x004 (R/W) Current Parallel Port Sizes Register */ + uint32_t RESERVED0[2U]; + __IOM uint32_t ACPR; /*!< Offset: 0x010 (R/W) Asynchronous Clock Prescaler Register */ + uint32_t RESERVED1[55U]; + __IOM uint32_t SPPR; /*!< Offset: 0x0F0 (R/W) Selected Pin Protocol Register */ + uint32_t RESERVED2[131U]; + __IM uint32_t FFSR; /*!< Offset: 0x300 (R/ ) Formatter and Flush Status Register */ + __IOM uint32_t FFCR; /*!< Offset: 0x304 (R/W) Formatter and Flush Control Register */ + __IOM uint32_t PSCR; /*!< Offset: 0x308 (R/W) Periodic Synchronization Control Register */ + uint32_t RESERVED3[809U]; + __OM uint32_t LAR; /*!< Offset: 0xFB0 ( /W) Software Lock Access Register */ + __IM uint32_t LSR; /*!< Offset: 0xFB4 (R/ ) Software Lock Status Register */ + uint32_t RESERVED4[4U]; + __IM uint32_t TYPE; /*!< Offset: 0xFC8 (R/ ) Device Identifier Register */ + __IM uint32_t DEVTYPE; /*!< Offset: 0xFCC (R/ ) Device Type Register */ +} TPI_Type; + +/* TPI Asynchronous Clock Prescaler Register Definitions */ +#define TPI_ACPR_SWOSCALER_Pos 0U /*!< TPI ACPR: SWOSCALER Position */ +#define TPI_ACPR_SWOSCALER_Msk (0xFFFFUL /*<< TPI_ACPR_SWOSCALER_Pos*/) /*!< TPI ACPR: SWOSCALER Mask */ + +/* TPI Selected Pin Protocol Register Definitions */ +#define TPI_SPPR_TXMODE_Pos 0U /*!< TPI SPPR: TXMODE Position */ +#define TPI_SPPR_TXMODE_Msk (0x3UL /*<< TPI_SPPR_TXMODE_Pos*/) /*!< TPI SPPR: TXMODE Mask */ + +/* TPI Formatter and Flush Status Register Definitions */ +#define TPI_FFSR_FtNonStop_Pos 3U /*!< TPI FFSR: FtNonStop Position */ +#define TPI_FFSR_FtNonStop_Msk (0x1UL << TPI_FFSR_FtNonStop_Pos) /*!< TPI FFSR: FtNonStop Mask */ + +#define TPI_FFSR_TCPresent_Pos 2U /*!< TPI FFSR: TCPresent Position */ +#define TPI_FFSR_TCPresent_Msk (0x1UL << TPI_FFSR_TCPresent_Pos) /*!< TPI FFSR: TCPresent Mask */ + +#define TPI_FFSR_FtStopped_Pos 1U /*!< TPI FFSR: FtStopped Position */ +#define TPI_FFSR_FtStopped_Msk (0x1UL << TPI_FFSR_FtStopped_Pos) /*!< TPI FFSR: FtStopped Mask */ + +#define TPI_FFSR_FlInProg_Pos 0U /*!< TPI FFSR: FlInProg Position */ +#define TPI_FFSR_FlInProg_Msk (0x1UL /*<< TPI_FFSR_FlInProg_Pos*/) /*!< TPI FFSR: FlInProg Mask */ + +/* TPI Formatter and Flush Control Register Definitions */ +#define TPI_FFCR_TrigIn_Pos 8U /*!< TPI FFCR: TrigIn Position */ +#define TPI_FFCR_TrigIn_Msk (0x1UL << TPI_FFCR_TrigIn_Pos) /*!< TPI FFCR: TrigIn Mask */ + +#define TPI_FFCR_FOnMan_Pos 6U /*!< TPI FFCR: FOnMan Position */ +#define TPI_FFCR_FOnMan_Msk (0x1UL << TPI_FFCR_FOnMan_Pos) /*!< TPI FFCR: FOnMan Mask */ + +#define TPI_FFCR_EnFCont_Pos 1U /*!< TPI FFCR: EnFCont Position */ +#define TPI_FFCR_EnFCont_Msk (0x1UL << TPI_FFCR_EnFCont_Pos) /*!< TPI FFCR: EnFCont Mask */ + +/* TPI Periodic Synchronization Control Register Definitions */ +#define TPI_PSCR_PSCount_Pos 0U /*!< TPI PSCR: PSCount Position */ +#define TPI_PSCR_PSCount_Msk (0x1FUL /*<< TPI_PSCR_PSCount_Pos*/) /*!< TPI PSCR: TPSCount Mask */ + +/* TPI Software Lock Status Register Definitions */ +#define TPI_LSR_nTT_Pos 1U /*!< TPI LSR: Not thirty-two bit. Position */ +#define TPI_LSR_nTT_Msk (0x1UL << TPI_LSR_nTT_Pos) /*!< TPI LSR: Not thirty-two bit. Mask */ + +#define TPI_LSR_SLK_Pos 1U /*!< TPI LSR: Software Lock status Position */ +#define TPI_LSR_SLK_Msk (0x1UL << TPI_LSR_SLK_Pos) /*!< TPI LSR: Software Lock status Mask */ + +#define TPI_LSR_SLI_Pos 0U /*!< TPI LSR: Software Lock implemented Position */ +#define TPI_LSR_SLI_Msk (0x1UL /*<< TPI_LSR_SLI_Pos*/) /*!< TPI LSR: Software Lock implemented Mask */ + +/* TPI DEVID Register Definitions */ +#define TPI_DEVID_NRZVALID_Pos 11U /*!< TPI DEVID: NRZVALID Position */ +#define TPI_DEVID_NRZVALID_Msk (0x1UL << TPI_DEVID_NRZVALID_Pos) /*!< TPI DEVID: NRZVALID Mask */ + +#define TPI_DEVID_MANCVALID_Pos 10U /*!< TPI DEVID: MANCVALID Position */ +#define TPI_DEVID_MANCVALID_Msk (0x1UL << TPI_DEVID_MANCVALID_Pos) /*!< TPI DEVID: MANCVALID Mask */ + +#define TPI_DEVID_PTINVALID_Pos 9U /*!< TPI DEVID: PTINVALID Position */ +#define TPI_DEVID_PTINVALID_Msk (0x1UL << TPI_DEVID_PTINVALID_Pos) /*!< TPI DEVID: PTINVALID Mask */ + +#define TPI_DEVID_FIFOSZ_Pos 6U /*!< TPI DEVID: FIFO depth Position */ +#define TPI_DEVID_FIFOSZ_Msk (0x7UL << TPI_DEVID_FIFOSZ_Pos) /*!< TPI DEVID: FIFO depth Mask */ + +/* TPI DEVTYPE Register Definitions */ +#define TPI_DEVTYPE_SubType_Pos 4U /*!< TPI DEVTYPE: SubType Position */ +#define TPI_DEVTYPE_SubType_Msk (0xFUL /*<< TPI_DEVTYPE_SubType_Pos*/) /*!< TPI DEVTYPE: SubType Mask */ + +#define TPI_DEVTYPE_MajorType_Pos 0U /*!< TPI DEVTYPE: MajorType Position */ +#define TPI_DEVTYPE_MajorType_Msk (0xFUL << TPI_DEVTYPE_MajorType_Pos) /*!< TPI DEVTYPE: MajorType Mask */ + +/*@}*/ /* end of group CMSIS_TPI */ + + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_MPU Memory Protection Unit (MPU) + \brief Type definitions for the Memory Protection Unit (MPU) + @{ + */ + +/** + \brief Structure type to access the Memory Protection Unit (MPU). + */ +typedef struct +{ + __IM uint32_t TYPE; /*!< Offset: 0x000 (R/ ) MPU Type Register */ + __IOM uint32_t CTRL; /*!< Offset: 0x004 (R/W) MPU Control Register */ + __IOM uint32_t RNR; /*!< Offset: 0x008 (R/W) MPU Region Number Register */ + __IOM uint32_t RBAR; /*!< Offset: 0x00C (R/W) MPU Region Base Address Register */ + __IOM uint32_t RLAR; /*!< Offset: 0x010 (R/W) MPU Region Limit Address Register */ + uint32_t RESERVED0[7U]; + union + { + __IOM uint32_t MAIR[2]; + struct + { + __IOM uint32_t MAIR0; /*!< Offset: 0x030 (R/W) MPU Memory Attribute Indirection Register 0 */ + __IOM uint32_t MAIR1; /*!< Offset: 0x034 (R/W) MPU Memory Attribute Indirection Register 1 */ + }; + }; +} MPU_Type; + +#define MPU_TYPE_RALIASES 1U + +/* MPU Type Register Definitions */ +#define MPU_TYPE_IREGION_Pos 16U /*!< MPU TYPE: IREGION Position */ +#define MPU_TYPE_IREGION_Msk (0xFFUL << MPU_TYPE_IREGION_Pos) /*!< MPU TYPE: IREGION Mask */ + +#define MPU_TYPE_DREGION_Pos 8U /*!< MPU TYPE: DREGION Position */ +#define MPU_TYPE_DREGION_Msk (0xFFUL << MPU_TYPE_DREGION_Pos) /*!< MPU TYPE: DREGION Mask */ + +#define MPU_TYPE_SEPARATE_Pos 0U /*!< MPU TYPE: SEPARATE Position */ +#define MPU_TYPE_SEPARATE_Msk (1UL /*<< MPU_TYPE_SEPARATE_Pos*/) /*!< MPU TYPE: SEPARATE Mask */ + +/* MPU Control Register Definitions */ +#define MPU_CTRL_PRIVDEFENA_Pos 2U /*!< MPU CTRL: PRIVDEFENA Position */ +#define MPU_CTRL_PRIVDEFENA_Msk (1UL << MPU_CTRL_PRIVDEFENA_Pos) /*!< MPU CTRL: PRIVDEFENA Mask */ + +#define MPU_CTRL_HFNMIENA_Pos 1U /*!< MPU CTRL: HFNMIENA Position */ +#define MPU_CTRL_HFNMIENA_Msk (1UL << MPU_CTRL_HFNMIENA_Pos) /*!< MPU CTRL: HFNMIENA Mask */ + +#define MPU_CTRL_ENABLE_Pos 0U /*!< MPU CTRL: ENABLE Position */ +#define MPU_CTRL_ENABLE_Msk (1UL /*<< MPU_CTRL_ENABLE_Pos*/) /*!< MPU CTRL: ENABLE Mask */ + +/* MPU Region Number Register Definitions */ +#define MPU_RNR_REGION_Pos 0U /*!< MPU RNR: REGION Position */ +#define MPU_RNR_REGION_Msk (0xFFUL /*<< MPU_RNR_REGION_Pos*/) /*!< MPU RNR: REGION Mask */ + +/* MPU Region Base Address Register Definitions */ +#define MPU_RBAR_BASE_Pos 5U /*!< MPU RBAR: BASE Position */ +#define MPU_RBAR_BASE_Msk (0x7FFFFFFUL << MPU_RBAR_BASE_Pos) /*!< MPU RBAR: BASE Mask */ + +#define MPU_RBAR_SH_Pos 3U /*!< MPU RBAR: SH Position */ +#define MPU_RBAR_SH_Msk (0x3UL << MPU_RBAR_SH_Pos) /*!< MPU RBAR: SH Mask */ + +#define MPU_RBAR_AP_Pos 1U /*!< MPU RBAR: AP Position */ +#define MPU_RBAR_AP_Msk (0x3UL << MPU_RBAR_AP_Pos) /*!< MPU RBAR: AP Mask */ + +#define MPU_RBAR_XN_Pos 0U /*!< MPU RBAR: XN Position */ +#define MPU_RBAR_XN_Msk (01UL /*<< MPU_RBAR_XN_Pos*/) /*!< MPU RBAR: XN Mask */ + +/* MPU Region Limit Address Register Definitions */ +#define MPU_RLAR_LIMIT_Pos 5U /*!< MPU RLAR: LIMIT Position */ +#define MPU_RLAR_LIMIT_Msk (0x7FFFFFFUL << MPU_RLAR_LIMIT_Pos) /*!< MPU RLAR: LIMIT Mask */ + +#define MPU_RLAR_AttrIndx_Pos 1U /*!< MPU RLAR: AttrIndx Position */ +#define MPU_RLAR_AttrIndx_Msk (0x7UL << MPU_RLAR_AttrIndx_Pos) /*!< MPU RLAR: AttrIndx Mask */ + +#define MPU_RLAR_EN_Pos 0U /*!< MPU RLAR: EN Position */ +#define MPU_RLAR_EN_Msk (1UL /*<< MPU_RLAR_EN_Pos*/) /*!< MPU RLAR: EN Mask */ + +/* MPU Memory Attribute Indirection Register 0 Definitions */ +#define MPU_MAIR0_Attr3_Pos 24U /*!< MPU MAIR0: Attr3 Position */ +#define MPU_MAIR0_Attr3_Msk (0xFFUL << MPU_MAIR0_Attr3_Pos) /*!< MPU MAIR0: Attr3 Mask */ + +#define MPU_MAIR0_Attr2_Pos 16U /*!< MPU MAIR0: Attr2 Position */ +#define MPU_MAIR0_Attr2_Msk (0xFFUL << MPU_MAIR0_Attr2_Pos) /*!< MPU MAIR0: Attr2 Mask */ + +#define MPU_MAIR0_Attr1_Pos 8U /*!< MPU MAIR0: Attr1 Position */ +#define MPU_MAIR0_Attr1_Msk (0xFFUL << MPU_MAIR0_Attr1_Pos) /*!< MPU MAIR0: Attr1 Mask */ + +#define MPU_MAIR0_Attr0_Pos 0U /*!< MPU MAIR0: Attr0 Position */ +#define MPU_MAIR0_Attr0_Msk (0xFFUL /*<< MPU_MAIR0_Attr0_Pos*/) /*!< MPU MAIR0: Attr0 Mask */ + +/* MPU Memory Attribute Indirection Register 1 Definitions */ +#define MPU_MAIR1_Attr7_Pos 24U /*!< MPU MAIR1: Attr7 Position */ +#define MPU_MAIR1_Attr7_Msk (0xFFUL << MPU_MAIR1_Attr7_Pos) /*!< MPU MAIR1: Attr7 Mask */ + +#define MPU_MAIR1_Attr6_Pos 16U /*!< MPU MAIR1: Attr6 Position */ +#define MPU_MAIR1_Attr6_Msk (0xFFUL << MPU_MAIR1_Attr6_Pos) /*!< MPU MAIR1: Attr6 Mask */ + +#define MPU_MAIR1_Attr5_Pos 8U /*!< MPU MAIR1: Attr5 Position */ +#define MPU_MAIR1_Attr5_Msk (0xFFUL << MPU_MAIR1_Attr5_Pos) /*!< MPU MAIR1: Attr5 Mask */ + +#define MPU_MAIR1_Attr4_Pos 0U /*!< MPU MAIR1: Attr4 Position */ +#define MPU_MAIR1_Attr4_Msk (0xFFUL /*<< MPU_MAIR1_Attr4_Pos*/) /*!< MPU MAIR1: Attr4 Mask */ + +/*@} end of group CMSIS_MPU */ +#endif + + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SAU Security Attribution Unit (SAU) + \brief Type definitions for the Security Attribution Unit (SAU) + @{ + */ + +/** + \brief Structure type to access the Security Attribution Unit (SAU). + */ +typedef struct +{ + __IOM uint32_t CTRL; /*!< Offset: 0x000 (R/W) SAU Control Register */ + __IM uint32_t TYPE; /*!< Offset: 0x004 (R/ ) SAU Type Register */ +#if defined (__SAUREGION_PRESENT) && (__SAUREGION_PRESENT == 1U) + __IOM uint32_t RNR; /*!< Offset: 0x008 (R/W) SAU Region Number Register */ + __IOM uint32_t RBAR; /*!< Offset: 0x00C (R/W) SAU Region Base Address Register */ + __IOM uint32_t RLAR; /*!< Offset: 0x010 (R/W) SAU Region Limit Address Register */ +#endif +} SAU_Type; + +/* SAU Control Register Definitions */ +#define SAU_CTRL_ALLNS_Pos 1U /*!< SAU CTRL: ALLNS Position */ +#define SAU_CTRL_ALLNS_Msk (1UL << SAU_CTRL_ALLNS_Pos) /*!< SAU CTRL: ALLNS Mask */ + +#define SAU_CTRL_ENABLE_Pos 0U /*!< SAU CTRL: ENABLE Position */ +#define SAU_CTRL_ENABLE_Msk (1UL /*<< SAU_CTRL_ENABLE_Pos*/) /*!< SAU CTRL: ENABLE Mask */ + +/* SAU Type Register Definitions */ +#define SAU_TYPE_SREGION_Pos 0U /*!< SAU TYPE: SREGION Position */ +#define SAU_TYPE_SREGION_Msk (0xFFUL /*<< SAU_TYPE_SREGION_Pos*/) /*!< SAU TYPE: SREGION Mask */ + +#if defined (__SAUREGION_PRESENT) && (__SAUREGION_PRESENT == 1U) +/* SAU Region Number Register Definitions */ +#define SAU_RNR_REGION_Pos 0U /*!< SAU RNR: REGION Position */ +#define SAU_RNR_REGION_Msk (0xFFUL /*<< SAU_RNR_REGION_Pos*/) /*!< SAU RNR: REGION Mask */ + +/* SAU Region Base Address Register Definitions */ +#define SAU_RBAR_BADDR_Pos 5U /*!< SAU RBAR: BADDR Position */ +#define SAU_RBAR_BADDR_Msk (0x7FFFFFFUL << SAU_RBAR_BADDR_Pos) /*!< SAU RBAR: BADDR Mask */ + +/* SAU Region Limit Address Register Definitions */ +#define SAU_RLAR_LADDR_Pos 5U /*!< SAU RLAR: LADDR Position */ +#define SAU_RLAR_LADDR_Msk (0x7FFFFFFUL << SAU_RLAR_LADDR_Pos) /*!< SAU RLAR: LADDR Mask */ + +#define SAU_RLAR_NSC_Pos 1U /*!< SAU RLAR: NSC Position */ +#define SAU_RLAR_NSC_Msk (1UL << SAU_RLAR_NSC_Pos) /*!< SAU RLAR: NSC Mask */ + +#define SAU_RLAR_ENABLE_Pos 0U /*!< SAU RLAR: ENABLE Position */ +#define SAU_RLAR_ENABLE_Msk (1UL /*<< SAU_RLAR_ENABLE_Pos*/) /*!< SAU RLAR: ENABLE Mask */ + +#endif /* defined (__SAUREGION_PRESENT) && (__SAUREGION_PRESENT == 1U) */ + +/*@} end of group CMSIS_SAU */ +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_CoreDebug Core Debug Registers (CoreDebug) + \brief Type definitions for the Core Debug Registers + @{ + */ + +/** + \brief Structure type to access the Core Debug Register (CoreDebug). + */ +typedef struct +{ + __IOM uint32_t DHCSR; /*!< Offset: 0x000 (R/W) Debug Halting Control and Status Register */ + __OM uint32_t DCRSR; /*!< Offset: 0x004 ( /W) Debug Core Register Selector Register */ + __IOM uint32_t DCRDR; /*!< Offset: 0x008 (R/W) Debug Core Register Data Register */ + __IOM uint32_t DEMCR; /*!< Offset: 0x00C (R/W) Debug Exception and Monitor Control Register */ + uint32_t RESERVED4[1U]; + __IOM uint32_t DAUTHCTRL; /*!< Offset: 0x014 (R/W) Debug Authentication Control Register */ + __IOM uint32_t DSCSR; /*!< Offset: 0x018 (R/W) Debug Security Control and Status Register */ +} CoreDebug_Type; + +/* Debug Halting Control and Status Register Definitions */ +#define CoreDebug_DHCSR_DBGKEY_Pos 16U /*!< CoreDebug DHCSR: DBGKEY Position */ +#define CoreDebug_DHCSR_DBGKEY_Msk (0xFFFFUL << CoreDebug_DHCSR_DBGKEY_Pos) /*!< CoreDebug DHCSR: DBGKEY Mask */ + +#define CoreDebug_DHCSR_S_RESTART_ST_Pos 26U /*!< CoreDebug DHCSR: S_RESTART_ST Position */ +#define CoreDebug_DHCSR_S_RESTART_ST_Msk (1UL << CoreDebug_DHCSR_S_RESTART_ST_Pos) /*!< CoreDebug DHCSR: S_RESTART_ST Mask */ + +#define CoreDebug_DHCSR_S_RESET_ST_Pos 25U /*!< CoreDebug DHCSR: S_RESET_ST Position */ +#define CoreDebug_DHCSR_S_RESET_ST_Msk (1UL << CoreDebug_DHCSR_S_RESET_ST_Pos) /*!< CoreDebug DHCSR: S_RESET_ST Mask */ + +#define CoreDebug_DHCSR_S_RETIRE_ST_Pos 24U /*!< CoreDebug DHCSR: S_RETIRE_ST Position */ +#define CoreDebug_DHCSR_S_RETIRE_ST_Msk (1UL << CoreDebug_DHCSR_S_RETIRE_ST_Pos) /*!< CoreDebug DHCSR: S_RETIRE_ST Mask */ + +#define CoreDebug_DHCSR_S_LOCKUP_Pos 19U /*!< CoreDebug DHCSR: S_LOCKUP Position */ +#define CoreDebug_DHCSR_S_LOCKUP_Msk (1UL << CoreDebug_DHCSR_S_LOCKUP_Pos) /*!< CoreDebug DHCSR: S_LOCKUP Mask */ + +#define CoreDebug_DHCSR_S_SLEEP_Pos 18U /*!< CoreDebug DHCSR: S_SLEEP Position */ +#define CoreDebug_DHCSR_S_SLEEP_Msk (1UL << CoreDebug_DHCSR_S_SLEEP_Pos) /*!< CoreDebug DHCSR: S_SLEEP Mask */ + +#define CoreDebug_DHCSR_S_HALT_Pos 17U /*!< CoreDebug DHCSR: S_HALT Position */ +#define CoreDebug_DHCSR_S_HALT_Msk (1UL << CoreDebug_DHCSR_S_HALT_Pos) /*!< CoreDebug DHCSR: S_HALT Mask */ + +#define CoreDebug_DHCSR_S_REGRDY_Pos 16U /*!< CoreDebug DHCSR: S_REGRDY Position */ +#define CoreDebug_DHCSR_S_REGRDY_Msk (1UL << CoreDebug_DHCSR_S_REGRDY_Pos) /*!< CoreDebug DHCSR: S_REGRDY Mask */ + +#define CoreDebug_DHCSR_C_MASKINTS_Pos 3U /*!< CoreDebug DHCSR: C_MASKINTS Position */ +#define CoreDebug_DHCSR_C_MASKINTS_Msk (1UL << CoreDebug_DHCSR_C_MASKINTS_Pos) /*!< CoreDebug DHCSR: C_MASKINTS Mask */ + +#define CoreDebug_DHCSR_C_STEP_Pos 2U /*!< CoreDebug DHCSR: C_STEP Position */ +#define CoreDebug_DHCSR_C_STEP_Msk (1UL << CoreDebug_DHCSR_C_STEP_Pos) /*!< CoreDebug DHCSR: C_STEP Mask */ + +#define CoreDebug_DHCSR_C_HALT_Pos 1U /*!< CoreDebug DHCSR: C_HALT Position */ +#define CoreDebug_DHCSR_C_HALT_Msk (1UL << CoreDebug_DHCSR_C_HALT_Pos) /*!< CoreDebug DHCSR: C_HALT Mask */ + +#define CoreDebug_DHCSR_C_DEBUGEN_Pos 0U /*!< CoreDebug DHCSR: C_DEBUGEN Position */ +#define CoreDebug_DHCSR_C_DEBUGEN_Msk (1UL /*<< CoreDebug_DHCSR_C_DEBUGEN_Pos*/) /*!< CoreDebug DHCSR: C_DEBUGEN Mask */ + +/* Debug Core Register Selector Register Definitions */ +#define CoreDebug_DCRSR_REGWnR_Pos 16U /*!< CoreDebug DCRSR: REGWnR Position */ +#define CoreDebug_DCRSR_REGWnR_Msk (1UL << CoreDebug_DCRSR_REGWnR_Pos) /*!< CoreDebug DCRSR: REGWnR Mask */ + +#define CoreDebug_DCRSR_REGSEL_Pos 0U /*!< CoreDebug DCRSR: REGSEL Position */ +#define CoreDebug_DCRSR_REGSEL_Msk (0x1FUL /*<< CoreDebug_DCRSR_REGSEL_Pos*/) /*!< CoreDebug DCRSR: REGSEL Mask */ + +/* Debug Exception and Monitor Control Register */ +#define CoreDebug_DEMCR_DWTENA_Pos 24U /*!< CoreDebug DEMCR: DWTENA Position */ +#define CoreDebug_DEMCR_DWTENA_Msk (1UL << CoreDebug_DEMCR_DWTENA_Pos) /*!< CoreDebug DEMCR: DWTENA Mask */ + +#define CoreDebug_DEMCR_VC_HARDERR_Pos 10U /*!< CoreDebug DEMCR: VC_HARDERR Position */ +#define CoreDebug_DEMCR_VC_HARDERR_Msk (1UL << CoreDebug_DEMCR_VC_HARDERR_Pos) /*!< CoreDebug DEMCR: VC_HARDERR Mask */ + +#define CoreDebug_DEMCR_VC_CORERESET_Pos 0U /*!< CoreDebug DEMCR: VC_CORERESET Position */ +#define CoreDebug_DEMCR_VC_CORERESET_Msk (1UL /*<< CoreDebug_DEMCR_VC_CORERESET_Pos*/) /*!< CoreDebug DEMCR: VC_CORERESET Mask */ + +/* Debug Authentication Control Register Definitions */ +#define CoreDebug_DAUTHCTRL_INTSPNIDEN_Pos 3U /*!< CoreDebug DAUTHCTRL: INTSPNIDEN, Position */ +#define CoreDebug_DAUTHCTRL_INTSPNIDEN_Msk (1UL << CoreDebug_DAUTHCTRL_INTSPNIDEN_Pos) /*!< CoreDebug DAUTHCTRL: INTSPNIDEN, Mask */ + +#define CoreDebug_DAUTHCTRL_SPNIDENSEL_Pos 2U /*!< CoreDebug DAUTHCTRL: SPNIDENSEL Position */ +#define CoreDebug_DAUTHCTRL_SPNIDENSEL_Msk (1UL << CoreDebug_DAUTHCTRL_SPNIDENSEL_Pos) /*!< CoreDebug DAUTHCTRL: SPNIDENSEL Mask */ + +#define CoreDebug_DAUTHCTRL_INTSPIDEN_Pos 1U /*!< CoreDebug DAUTHCTRL: INTSPIDEN Position */ +#define CoreDebug_DAUTHCTRL_INTSPIDEN_Msk (1UL << CoreDebug_DAUTHCTRL_INTSPIDEN_Pos) /*!< CoreDebug DAUTHCTRL: INTSPIDEN Mask */ + +#define CoreDebug_DAUTHCTRL_SPIDENSEL_Pos 0U /*!< CoreDebug DAUTHCTRL: SPIDENSEL Position */ +#define CoreDebug_DAUTHCTRL_SPIDENSEL_Msk (1UL /*<< CoreDebug_DAUTHCTRL_SPIDENSEL_Pos*/) /*!< CoreDebug DAUTHCTRL: SPIDENSEL Mask */ + +/* Debug Security Control and Status Register Definitions */ +#define CoreDebug_DSCSR_CDS_Pos 16U /*!< CoreDebug DSCSR: CDS Position */ +#define CoreDebug_DSCSR_CDS_Msk (1UL << CoreDebug_DSCSR_CDS_Pos) /*!< CoreDebug DSCSR: CDS Mask */ + +#define CoreDebug_DSCSR_SBRSEL_Pos 1U /*!< CoreDebug DSCSR: SBRSEL Position */ +#define CoreDebug_DSCSR_SBRSEL_Msk (1UL << CoreDebug_DSCSR_SBRSEL_Pos) /*!< CoreDebug DSCSR: SBRSEL Mask */ + +#define CoreDebug_DSCSR_SBRSELEN_Pos 0U /*!< CoreDebug DSCSR: SBRSELEN Position */ +#define CoreDebug_DSCSR_SBRSELEN_Msk (1UL /*<< CoreDebug_DSCSR_SBRSELEN_Pos*/) /*!< CoreDebug DSCSR: SBRSELEN Mask */ + +/*@} end of group CMSIS_CoreDebug */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_core_bitfield Core register bit field macros + \brief Macros for use with bit field definitions (xxx_Pos, xxx_Msk). + @{ + */ + +/** + \brief Mask and shift a bit field value for use in a register bit range. + \param[in] field Name of the register bit field. + \param[in] value Value of the bit field. This parameter is interpreted as an uint32_t type. + \return Masked and shifted value. +*/ +#define _VAL2FLD(field, value) (((uint32_t)(value) << field ## _Pos) & field ## _Msk) + +/** + \brief Mask and shift a register value to extract a bit filed value. + \param[in] field Name of the register bit field. + \param[in] value Value of register. This parameter is interpreted as an uint32_t type. + \return Masked and shifted bit field value. +*/ +#define _FLD2VAL(field, value) (((uint32_t)(value) & field ## _Msk) >> field ## _Pos) + +/*@} end of group CMSIS_core_bitfield */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_core_base Core Definitions + \brief Definitions for base addresses, unions, and structures. + @{ + */ + +/* Memory mapping of Core Hardware */ +#define SCS_BASE (0xE000E000UL) /*!< System Control Space Base Address */ +#define DWT_BASE (0xE0001000UL) /*!< DWT Base Address */ +#define TPI_BASE (0xE0040000UL) /*!< TPI Base Address */ +#define CoreDebug_BASE (0xE000EDF0UL) /*!< Core Debug Base Address */ +#define SysTick_BASE (SCS_BASE + 0x0010UL) /*!< SysTick Base Address */ +#define NVIC_BASE (SCS_BASE + 0x0100UL) /*!< NVIC Base Address */ +#define SCB_BASE (SCS_BASE + 0x0D00UL) /*!< System Control Block Base Address */ + + +#define SCB ((SCB_Type *) SCB_BASE ) /*!< SCB configuration struct */ +#define SysTick ((SysTick_Type *) SysTick_BASE ) /*!< SysTick configuration struct */ +#define NVIC ((NVIC_Type *) NVIC_BASE ) /*!< NVIC configuration struct */ +#define DWT ((DWT_Type *) DWT_BASE ) /*!< DWT configuration struct */ +#define TPI ((TPI_Type *) TPI_BASE ) /*!< TPI configuration struct */ +#define CoreDebug ((CoreDebug_Type *) CoreDebug_BASE ) /*!< Core Debug configuration struct */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) +#define MPU_BASE (SCS_BASE + 0x0D90UL) /*!< Memory Protection Unit */ +#define MPU ((MPU_Type *) MPU_BASE ) /*!< Memory Protection Unit */ +#endif + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +#define SAU_BASE (SCS_BASE + 0x0DD0UL) /*!< Security Attribution Unit */ +#define SAU ((SAU_Type *) SAU_BASE ) /*!< Security Attribution Unit */ +#endif + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +#define SCS_BASE_NS (0xE002E000UL) /*!< System Control Space Base Address (non-secure address space) */ +#define CoreDebug_BASE_NS (0xE002EDF0UL) /*!< Core Debug Base Address (non-secure address space) */ +#define SysTick_BASE_NS (SCS_BASE_NS + 0x0010UL) /*!< SysTick Base Address (non-secure address space) */ +#define NVIC_BASE_NS (SCS_BASE_NS + 0x0100UL) /*!< NVIC Base Address (non-secure address space) */ +#define SCB_BASE_NS (SCS_BASE_NS + 0x0D00UL) /*!< System Control Block Base Address (non-secure address space) */ + +#define SCB_NS ((SCB_Type *) SCB_BASE_NS ) /*!< SCB configuration struct (non-secure address space) */ +#define SysTick_NS ((SysTick_Type *) SysTick_BASE_NS ) /*!< SysTick configuration struct (non-secure address space) */ +#define NVIC_NS ((NVIC_Type *) NVIC_BASE_NS ) /*!< NVIC configuration struct (non-secure address space) */ +#define CoreDebug_NS ((CoreDebug_Type *) CoreDebug_BASE_NS) /*!< Core Debug configuration struct (non-secure address space) */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) +#define MPU_BASE_NS (SCS_BASE_NS + 0x0D90UL) /*!< Memory Protection Unit (non-secure address space) */ +#define MPU_NS ((MPU_Type *) MPU_BASE_NS ) /*!< Memory Protection Unit (non-secure address space) */ +#endif + +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ +/*@} */ + + + +/******************************************************************************* + * Hardware Abstraction Layer + Core Function Interface contains: + - Core NVIC Functions + - Core SysTick Functions + - Core Register Access Functions + ******************************************************************************/ +/** + \defgroup CMSIS_Core_FunctionInterface Functions and Instructions Reference +*/ + + + +/* ########################## NVIC functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_NVICFunctions NVIC Functions + \brief Functions that manage interrupts and exceptions via the NVIC. + @{ + */ + +#ifdef CMSIS_NVIC_VIRTUAL +#ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE +#define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h" +#endif +#include CMSIS_NVIC_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetPriorityGrouping __NVIC_SetPriorityGrouping +#define NVIC_GetPriorityGrouping __NVIC_GetPriorityGrouping +#define NVIC_EnableIRQ __NVIC_EnableIRQ +#define NVIC_GetEnableIRQ __NVIC_GetEnableIRQ +#define NVIC_DisableIRQ __NVIC_DisableIRQ +#define NVIC_GetPendingIRQ __NVIC_GetPendingIRQ +#define NVIC_SetPendingIRQ __NVIC_SetPendingIRQ +#define NVIC_ClearPendingIRQ __NVIC_ClearPendingIRQ +#define NVIC_GetActive __NVIC_GetActive +#define NVIC_SetPriority __NVIC_SetPriority +#define NVIC_GetPriority __NVIC_GetPriority +#define NVIC_SystemReset __NVIC_SystemReset +#endif /* CMSIS_NVIC_VIRTUAL */ + +#ifdef CMSIS_VECTAB_VIRTUAL +#ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h" +#endif +#include CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetVector __NVIC_SetVector +#define NVIC_GetVector __NVIC_GetVector +#endif /* (CMSIS_VECTAB_VIRTUAL) */ + +#define NVIC_USER_IRQ_OFFSET 16 + + +/* Special LR values for Secure/Non-Secure call handling and exception handling */ + +/* Function Return Payload (from ARMv8-M Architecture Reference Manual) LR value on entry from Secure BLXNS */ +#define FNC_RETURN (0xFEFFFFFFUL) /* bit [0] ignored when processing a branch */ + +/* The following EXC_RETURN mask values are used to evaluate the LR on exception entry */ +#define EXC_RETURN_PREFIX (0xFF000000UL) /* bits [31:24] set to indicate an EXC_RETURN value */ +#define EXC_RETURN_S (0x00000040UL) /* bit [6] stack used to push registers: 0=Non-secure 1=Secure */ +#define EXC_RETURN_DCRS (0x00000020UL) /* bit [5] stacking rules for called registers: 0=skipped 1=saved */ +#define EXC_RETURN_FTYPE (0x00000010UL) /* bit [4] allocate stack for floating-point context: 0=done 1=skipped */ +#define EXC_RETURN_MODE (0x00000008UL) /* bit [3] processor mode for return: 0=Handler mode 1=Thread mode */ +#define EXC_RETURN_SPSEL (0x00000002UL) /* bit [1] stack pointer used to restore context: 0=MSP 1=PSP */ +#define EXC_RETURN_ES (0x00000001UL) /* bit [0] security state exception was taken to: 0=Non-secure 1=Secure */ + +/* Integrity Signature (from ARMv8-M Architecture Reference Manual) for exception context stacking */ +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) /* Value for processors with floating-point extension: */ +#define EXC_INTEGRITY_SIGNATURE (0xFEFA125AUL) /* bit [0] SFTC must match LR bit[4] EXC_RETURN_FTYPE */ +#else +#define EXC_INTEGRITY_SIGNATURE (0xFEFA125BUL) /* Value for processors without floating-point extension */ +#endif + + +/* Interrupt Priorities are WORD accessible only under Armv6-M */ +/* The following MACROS handle generation of the register offset and byte masks */ +#define _BIT_SHIFT(IRQn) ( ((((uint32_t)(int32_t)(IRQn)) ) & 0x03UL) * 8UL) +#define _SHP_IDX(IRQn) ( (((((uint32_t)(int32_t)(IRQn)) & 0x0FUL)-8UL) >> 2UL) ) +#define _IP_IDX(IRQn) ( (((uint32_t)(int32_t)(IRQn)) >> 2UL) ) + +#define __NVIC_SetPriorityGrouping(X) (void)(X) +#define __NVIC_GetPriorityGrouping() (0U) + +/** + \brief Enable Interrupt + \details Enables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Interrupt Enable status + \details Returns a device specific interrupt enable status from the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Disable Interrupt + \details Disables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + __DSB(); + __ISB(); + } +} + + +/** + \brief Get Pending Interrupt + \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not pending. + \return 1 Interrupt status is pending. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Pending Interrupt + \details Sets the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Clear Pending Interrupt + \details Clears the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Active Interrupt + \details Reads the active register in the NVIC and returns the active bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not active. + \return 1 Interrupt status is active. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetActive(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->IABR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \brief Get Interrupt Target State + \details Reads the interrupt target field in the NVIC and returns the interrupt target bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 if interrupt is assigned to Secure + \return 1 if interrupt is assigned to Non Secure + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t NVIC_GetTargetState(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Interrupt Target State + \details Sets the interrupt target field in the NVIC and returns the interrupt target bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 if interrupt is assigned to Secure + 1 if interrupt is assigned to Non Secure + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t NVIC_SetTargetState(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] |= ((uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL))); + return ((uint32_t)(((NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Clear Interrupt Target State + \details Clears the interrupt target field in the NVIC and returns the interrupt target bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 if interrupt is assigned to Secure + 1 if interrupt is assigned to Non Secure + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t NVIC_ClearTargetState(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] &= ~((uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL))); + return ((uint32_t)(((NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + + +/** + \brief Set Interrupt Priority + \details Sets the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \param [in] priority Priority to set. + \note The priority cannot be set for every processor exception. + */ +__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->IPR[_IP_IDX(IRQn)] = ((uint32_t)(NVIC->IPR[_IP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); + } + else + { + SCB->SHPR[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHPR[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); + } +} + + +/** + \brief Get Interrupt Priority + \details Reads the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Interrupt Priority. + Value is aligned automatically to the implemented priority bits of the microcontroller. + */ +__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn) +{ + + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->IPR[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + } + else + { + return ((uint32_t)(((SCB->SHPR[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + } +} + + +/** + \brief Encode Priority + \details Encodes the priority for an interrupt with the given priority group, + preemptive priority value, and subpriority value. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set. + \param [in] PriorityGroup Used priority group. + \param [in] PreemptPriority Preemptive priority value (starting from 0). + \param [in] SubPriority Subpriority value (starting from 0). + \return Encoded priority. Value can be used in the function \ref NVIC_SetPriority(). + */ +__STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority) +{ + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + uint32_t PreemptPriorityBits; + uint32_t SubPriorityBits; + + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); + SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + + return ( + ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) | + ((SubPriority & (uint32_t)((1UL << (SubPriorityBits )) - 1UL))) + ); +} + + +/** + \brief Decode Priority + \details Decodes an interrupt priority value with a given priority group to + preemptive priority value and subpriority value. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set. + \param [in] Priority Priority value, which can be retrieved with the function \ref NVIC_GetPriority(). + \param [in] PriorityGroup Used priority group. + \param [out] pPreemptPriority Preemptive priority value (starting from 0). + \param [out] pSubPriority Subpriority value (starting from 0). + */ +__STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* const pPreemptPriority, uint32_t* const pSubPriority) +{ + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + uint32_t PreemptPriorityBits; + uint32_t SubPriorityBits; + + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); + SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + + *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL); + *pSubPriority = (Priority ) & (uint32_t)((1UL << (SubPriorityBits )) - 1UL); +} + + +/** + \brief Set Interrupt Vector + \details Sets an interrupt vector in SRAM based interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + VTOR must been relocated to SRAM before. + If VTOR is not present address 0 must be mapped to SRAM. + \param [in] IRQn Interrupt number + \param [in] vector Address of interrupt handler function + */ +__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector) +{ +#if defined (__VTOR_PRESENT) && (__VTOR_PRESENT == 1U) + uint32_t* vectors = (uint32_t*)SCB->VTOR; +#else + uint32_t* vectors = (uint32_t*)0x0U; +#endif + vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector; +} + + +/** + \brief Get Interrupt Vector + \details Reads an interrupt vector from interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Address of interrupt handler function + */ +__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn) +{ +#if defined (__VTOR_PRESENT) && (__VTOR_PRESENT == 1U) + uint32_t* vectors = (uint32_t*)SCB->VTOR; +#else + uint32_t* vectors = (uint32_t*)0x0U; +#endif + return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET]; +} + + +/** + \brief System Reset + \details Initiates a system reset request to reset the MCU. + */ +__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void) +{ + __DSB(); /* Ensure all outstanding memory accesses included + buffered write are completed before reset */ + SCB->AIRCR = ((0x5FAUL << SCB_AIRCR_VECTKEY_Pos) | + SCB_AIRCR_SYSRESETREQ_Msk); + __DSB(); /* Ensure completion of memory access */ + + for (;;) /* wait until reset */ + { + __NOP(); + } +} + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \brief Enable Interrupt (non-secure) + \details Enables a device specific interrupt in the non-secure NVIC interrupt controller when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_EnableIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ISER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Interrupt Enable status (non-secure) + \details Returns a device specific interrupt enable status from the non-secure NVIC interrupt controller when in secure state. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetEnableIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC_NS->ISER[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Disable Interrupt (non-secure) + \details Disables a device specific interrupt in the non-secure NVIC interrupt controller when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_DisableIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ICER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Pending Interrupt (non-secure) + \details Reads the NVIC pending register in the non-secure NVIC when in secure state and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not pending. + \return 1 Interrupt status is pending. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetPendingIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC_NS->ISPR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Pending Interrupt (non-secure) + \details Sets the pending bit of a device specific interrupt in the non-secure NVIC pending register when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_SetPendingIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ISPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Clear Pending Interrupt (non-secure) + \details Clears the pending bit of a device specific interrupt in the non-secure NVIC pending register when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_ClearPendingIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ICPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Active Interrupt (non-secure) + \details Reads the active register in non-secure NVIC when in secure state and returns the active bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not active. + \return 1 Interrupt status is active. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetActive_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC_NS->IABR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Interrupt Priority (non-secure) + \details Sets the priority of a non-secure device specific interrupt or a non-secure processor exception when in secure state. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \param [in] priority Priority to set. + \note The priority cannot be set for every non-secure processor exception. + */ +__STATIC_INLINE void TZ_NVIC_SetPriority_NS(IRQn_Type IRQn, uint32_t priority) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->IPR[_IP_IDX(IRQn)] = ((uint32_t)(NVIC_NS->IPR[_IP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); + } + else + { + SCB_NS->SHPR[_SHP_IDX(IRQn)] = ((uint32_t)(SCB_NS->SHPR[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); + } +} + + +/** + \brief Get Interrupt Priority (non-secure) + \details Reads the priority of a non-secure device specific interrupt or a non-secure processor exception when in secure state. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Interrupt Priority. Value is aligned automatically to the implemented priority bits of the microcontroller. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetPriority_NS(IRQn_Type IRQn) +{ + + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC_NS->IPR[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + } + else + { + return ((uint32_t)(((SCB_NS->SHPR[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + } +} +#endif /* defined (__ARM_FEATURE_CMSE) &&(__ARM_FEATURE_CMSE == 3U) */ + +/*@} end of CMSIS_Core_NVICFunctions */ + +/* ########################## MPU functions #################################### */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) + +#include "mpu_armv8.h" + +#endif + +/* ########################## FPU functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_FpuFunctions FPU Functions + \brief Function that provides FPU type. + @{ + */ + +/** + \brief get FPU type + \details returns the FPU type + \returns + - \b 0: No FPU + - \b 1: Single precision FPU + - \b 2: Double + Single precision FPU + */ +__STATIC_INLINE uint32_t SCB_GetFPUType(void) +{ + return 0U; /* No FPU */ +} + + +/*@} end of CMSIS_Core_FpuFunctions */ + + + +/* ########################## SAU functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_SAUFunctions SAU Functions + \brief Functions that configure the SAU. + @{ + */ + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) + +/** + \brief Enable SAU + \details Enables the Security Attribution Unit (SAU). + */ +__STATIC_INLINE void TZ_SAU_Enable(void) +{ + SAU->CTRL |= (SAU_CTRL_ENABLE_Msk); +} + + + +/** + \brief Disable SAU + \details Disables the Security Attribution Unit (SAU). + */ +__STATIC_INLINE void TZ_SAU_Disable(void) +{ + SAU->CTRL &= ~(SAU_CTRL_ENABLE_Msk); +} + +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + +/*@} end of CMSIS_Core_SAUFunctions */ + + + + +/* ################################## SysTick function ############################################ */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_SysTickFunctions SysTick Functions + \brief Functions that configure the System. + @{ + */ + +#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U) + +/** + \brief System Tick Configuration + \details Initializes the System Timer and its interrupt, and starts the System Tick Timer. + Counter is in free running mode to generate periodic interrupts. + \param [in] ticks Number of ticks between two interrupts. + \return 0 Function succeeded. + \return 1 Function failed. + \note When the variable __Vendor_SysTickConfig is set to 1, then the + function SysTick_Config is not included. In this case, the file device.h + must contain a vendor-specific implementation of this function. + */ +__STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks) +{ + if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk) + { + return (1UL); /* Reload value impossible */ + } + + SysTick->LOAD = (uint32_t)(ticks - 1UL); /* set reload register */ + NVIC_SetPriority (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */ + SysTick->VAL = 0UL; /* Load the SysTick Counter Value */ + SysTick->CTRL = SysTick_CTRL_CLKSOURCE_Msk | + SysTick_CTRL_TICKINT_Msk | + SysTick_CTRL_ENABLE_Msk; /* Enable SysTick IRQ and SysTick Timer */ + return (0UL); /* Function successful */ +} + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \brief System Tick Configuration (non-secure) + \details Initializes the non-secure System Timer and its interrupt when in secure state, and starts the System Tick Timer. + Counter is in free running mode to generate periodic interrupts. + \param [in] ticks Number of ticks between two interrupts. + \return 0 Function succeeded. + \return 1 Function failed. + \note When the variable __Vendor_SysTickConfig is set to 1, then the + function TZ_SysTick_Config_NS is not included. In this case, the file device.h + must contain a vendor-specific implementation of this function. + + */ +__STATIC_INLINE uint32_t TZ_SysTick_Config_NS(uint32_t ticks) +{ + if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk) + { + return (1UL); /* Reload value impossible */ + } + + SysTick_NS->LOAD = (uint32_t)(ticks - 1UL); /* set reload register */ + TZ_NVIC_SetPriority_NS (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */ + SysTick_NS->VAL = 0UL; /* Load the SysTick Counter Value */ + SysTick_NS->CTRL = SysTick_CTRL_CLKSOURCE_Msk | + SysTick_CTRL_TICKINT_Msk | + SysTick_CTRL_ENABLE_Msk; /* Enable SysTick IRQ and SysTick Timer */ + return (0UL); /* Function successful */ +} +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + +#endif + +/*@} end of CMSIS_Core_SysTickFunctions */ + + + + +#ifdef __cplusplus +} +#endif + +#endif /* __CORE_ARMV8MBL_H_DEPENDANT */ + +#endif /* __CMSIS_GENERIC */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/core_armv8mml.h b/EpsilonLights/Drivers/CMSIS/Include/core_armv8mml.h new file mode 100644 index 00000000..da4340b7 --- /dev/null +++ b/EpsilonLights/Drivers/CMSIS/Include/core_armv8mml.h @@ -0,0 +1,2932 @@ +/**************************************************************************//** + * @file core_armv8mml.h + * @brief CMSIS Armv8-M Mainline Core Peripheral Access Layer Header File + * @version V5.0.7 + * @date 06. July 2018 + ******************************************************************************/ +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ + +#if defined ( __ICCARM__ ) +#pragma system_include /* treat file as system include file for MISRA check */ +#elif defined (__clang__) +#pragma clang system_header /* treat file as system include file */ +#endif + +#ifndef __CORE_ARMV8MML_H_GENERIC +#define __CORE_ARMV8MML_H_GENERIC + +#include + +#ifdef __cplusplus +extern "C" { +#endif + +/** + \page CMSIS_MISRA_Exceptions MISRA-C:2004 Compliance Exceptions + CMSIS violates the following MISRA-C:2004 rules: + + \li Required Rule 8.5, object/function definition in header file.
+ Function definitions in header files are used to allow 'inlining'. + + \li Required Rule 18.4, declaration of union type or object of union type: '{...}'.
+ Unions are used for effective representation of core registers. + + \li Advisory Rule 19.7, Function-like macro defined.
+ Function-like macros are used to allow more efficient code. + */ + + +/******************************************************************************* + * CMSIS definitions + ******************************************************************************/ +/** + \ingroup Cortex_ARMv8MML + @{ + */ + +#include "cmsis_version.h" + +/* CMSIS Armv8MML definitions */ +#define __ARMv8MML_CMSIS_VERSION_MAIN (__CM_CMSIS_VERSION_MAIN) /*!< \deprecated [31:16] CMSIS HAL main version */ +#define __ARMv8MML_CMSIS_VERSION_SUB (__CM_CMSIS_VERSION_SUB) /*!< \deprecated [15:0] CMSIS HAL sub version */ +#define __ARMv8MML_CMSIS_VERSION ((__ARMv8MML_CMSIS_VERSION_MAIN << 16U) | \ + __ARMv8MML_CMSIS_VERSION_SUB ) /*!< \deprecated CMSIS HAL version number */ + +#define __CORTEX_M (81U) /*!< Cortex-M Core */ + +/** __FPU_USED indicates whether an FPU is used or not. + For this, __FPU_PRESENT has to be checked prior to making use of FPU specific registers and functions. +*/ +#if defined ( __CC_ARM ) +#if defined __TARGET_FPU_VFP +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) +#define __FPU_USED 1U +#else +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#define __FPU_USED 0U +#endif +#else +#define __FPU_USED 0U +#endif + +#if defined(__ARM_FEATURE_DSP) +#if defined(__DSP_PRESENT) && (__DSP_PRESENT == 1U) +#define __DSP_USED 1U +#else +#error "Compiler generates DSP (SIMD) instructions for a devices without DSP extensions (check __DSP_PRESENT)" +#define __DSP_USED 0U +#endif +#else +#define __DSP_USED 0U +#endif + +#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#if defined __ARM_PCS_VFP +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) +#define __FPU_USED 1U +#else +#warning "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#define __FPU_USED 0U +#endif +#else +#define __FPU_USED 0U +#endif + +#if defined(__ARM_FEATURE_DSP) +#if defined(__DSP_PRESENT) && (__DSP_PRESENT == 1U) +#define __DSP_USED 1U +#else +#error "Compiler generates DSP (SIMD) instructions for a devices without DSP extensions (check __DSP_PRESENT)" +#define __DSP_USED 0U +#endif +#else +#define __DSP_USED 0U +#endif + +#elif defined ( __GNUC__ ) +#if defined (__VFP_FP__) && !defined(__SOFTFP__) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) +#define __FPU_USED 1U +#else +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#define __FPU_USED 0U +#endif +#else +#define __FPU_USED 0U +#endif + +#if defined(__ARM_FEATURE_DSP) +#if defined(__DSP_PRESENT) && (__DSP_PRESENT == 1U) +#define __DSP_USED 1U +#else +#error "Compiler generates DSP (SIMD) instructions for a devices without DSP extensions (check __DSP_PRESENT)" +#define __DSP_USED 0U +#endif +#else +#define __DSP_USED 0U +#endif + +#elif defined ( __ICCARM__ ) +#if defined __ARMVFP__ +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) +#define __FPU_USED 1U +#else +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#define __FPU_USED 0U +#endif +#else +#define __FPU_USED 0U +#endif + +#if defined(__ARM_FEATURE_DSP) +#if defined(__DSP_PRESENT) && (__DSP_PRESENT == 1U) +#define __DSP_USED 1U +#else +#error "Compiler generates DSP (SIMD) instructions for a devices without DSP extensions (check __DSP_PRESENT)" +#define __DSP_USED 0U +#endif +#else +#define __DSP_USED 0U +#endif + +#elif defined ( __TI_ARM__ ) +#if defined __TI_VFP_SUPPORT__ +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) +#define __FPU_USED 1U +#else +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#define __FPU_USED 0U +#endif +#else +#define __FPU_USED 0U +#endif + +#elif defined ( __TASKING__ ) +#if defined __FPU_VFP__ +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) +#define __FPU_USED 1U +#else +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#define __FPU_USED 0U +#endif +#else +#define __FPU_USED 0U +#endif + +#elif defined ( __CSMC__ ) +#if ( __CSMC__ & 0x400U) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) +#define __FPU_USED 1U +#else +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#define __FPU_USED 0U +#endif +#else +#define __FPU_USED 0U +#endif + +#endif + +#include "cmsis_compiler.h" /* CMSIS compiler specific defines */ + + +#ifdef __cplusplus +} +#endif + +#endif /* __CORE_ARMV8MML_H_GENERIC */ + +#ifndef __CMSIS_GENERIC + +#ifndef __CORE_ARMV8MML_H_DEPENDANT +#define __CORE_ARMV8MML_H_DEPENDANT + +#ifdef __cplusplus +extern "C" { +#endif + +/* check device defines and use defaults */ +#if defined __CHECK_DEVICE_DEFINES +#ifndef __ARMv8MML_REV +#define __ARMv8MML_REV 0x0000U +#warning "__ARMv8MML_REV not defined in device header file; using default!" +#endif + +#ifndef __FPU_PRESENT +#define __FPU_PRESENT 0U +#warning "__FPU_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __MPU_PRESENT +#define __MPU_PRESENT 0U +#warning "__MPU_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __SAUREGION_PRESENT +#define __SAUREGION_PRESENT 0U +#warning "__SAUREGION_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __DSP_PRESENT +#define __DSP_PRESENT 0U +#warning "__DSP_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __NVIC_PRIO_BITS +#define __NVIC_PRIO_BITS 3U +#warning "__NVIC_PRIO_BITS not defined in device header file; using default!" +#endif + +#ifndef __Vendor_SysTickConfig +#define __Vendor_SysTickConfig 0U +#warning "__Vendor_SysTickConfig not defined in device header file; using default!" +#endif +#endif + +/* IO definitions (access restrictions to peripheral registers) */ +/** + \defgroup CMSIS_glob_defs CMSIS Global Defines + + IO Type Qualifiers are used + \li to specify the access to peripheral variables. + \li for automatic generation of peripheral register debug information. +*/ +#ifdef __cplusplus +#define __I volatile /*!< Defines 'read only' permissions */ +#else +#define __I volatile const /*!< Defines 'read only' permissions */ +#endif +#define __O volatile /*!< Defines 'write only' permissions */ +#define __IO volatile /*!< Defines 'read / write' permissions */ + +/* following defines should be used for structure members */ +#define __IM volatile const /*! Defines 'read only' structure member permissions */ +#define __OM volatile /*! Defines 'write only' structure member permissions */ +#define __IOM volatile /*! Defines 'read / write' structure member permissions */ + +/*@} end of group ARMv8MML */ + + + +/******************************************************************************* + * Register Abstraction + Core Register contain: + - Core Register + - Core NVIC Register + - Core SCB Register + - Core SysTick Register + - Core Debug Register + - Core MPU Register + - Core SAU Register + - Core FPU Register + ******************************************************************************/ +/** + \defgroup CMSIS_core_register Defines and Type Definitions + \brief Type definitions and defines for Cortex-M processor based devices. +*/ + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_CORE Status and Control Registers + \brief Core Register type definitions. + @{ + */ + +/** + \brief Union type to access the Application Program Status Register (APSR). + */ +typedef union +{ + struct + { + uint32_t _reserved0: 16; /*!< bit: 0..15 Reserved */ + uint32_t GE: 4; /*!< bit: 16..19 Greater than or Equal flags */ + uint32_t _reserved1: 7; /*!< bit: 20..26 Reserved */ + uint32_t Q: 1; /*!< bit: 27 Saturation condition flag */ + uint32_t V: 1; /*!< bit: 28 Overflow condition code flag */ + uint32_t C: 1; /*!< bit: 29 Carry condition code flag */ + uint32_t Z: 1; /*!< bit: 30 Zero condition code flag */ + uint32_t N: 1; /*!< bit: 31 Negative condition code flag */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} APSR_Type; + +/* APSR Register Definitions */ +#define APSR_N_Pos 31U /*!< APSR: N Position */ +#define APSR_N_Msk (1UL << APSR_N_Pos) /*!< APSR: N Mask */ + +#define APSR_Z_Pos 30U /*!< APSR: Z Position */ +#define APSR_Z_Msk (1UL << APSR_Z_Pos) /*!< APSR: Z Mask */ + +#define APSR_C_Pos 29U /*!< APSR: C Position */ +#define APSR_C_Msk (1UL << APSR_C_Pos) /*!< APSR: C Mask */ + +#define APSR_V_Pos 28U /*!< APSR: V Position */ +#define APSR_V_Msk (1UL << APSR_V_Pos) /*!< APSR: V Mask */ + +#define APSR_Q_Pos 27U /*!< APSR: Q Position */ +#define APSR_Q_Msk (1UL << APSR_Q_Pos) /*!< APSR: Q Mask */ + +#define APSR_GE_Pos 16U /*!< APSR: GE Position */ +#define APSR_GE_Msk (0xFUL << APSR_GE_Pos) /*!< APSR: GE Mask */ + + +/** + \brief Union type to access the Interrupt Program Status Register (IPSR). + */ +typedef union +{ + struct + { + uint32_t ISR: 9; /*!< bit: 0.. 8 Exception number */ + uint32_t _reserved0: 23; /*!< bit: 9..31 Reserved */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} IPSR_Type; + +/* IPSR Register Definitions */ +#define IPSR_ISR_Pos 0U /*!< IPSR: ISR Position */ +#define IPSR_ISR_Msk (0x1FFUL /*<< IPSR_ISR_Pos*/) /*!< IPSR: ISR Mask */ + + +/** + \brief Union type to access the Special-Purpose Program Status Registers (xPSR). + */ +typedef union +{ + struct + { + uint32_t ISR: 9; /*!< bit: 0.. 8 Exception number */ + uint32_t _reserved0: 7; /*!< bit: 9..15 Reserved */ + uint32_t GE: 4; /*!< bit: 16..19 Greater than or Equal flags */ + uint32_t _reserved1: 4; /*!< bit: 20..23 Reserved */ + uint32_t T: 1; /*!< bit: 24 Thumb bit (read 0) */ + uint32_t IT: 2; /*!< bit: 25..26 saved IT state (read 0) */ + uint32_t Q: 1; /*!< bit: 27 Saturation condition flag */ + uint32_t V: 1; /*!< bit: 28 Overflow condition code flag */ + uint32_t C: 1; /*!< bit: 29 Carry condition code flag */ + uint32_t Z: 1; /*!< bit: 30 Zero condition code flag */ + uint32_t N: 1; /*!< bit: 31 Negative condition code flag */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} xPSR_Type; + +/* xPSR Register Definitions */ +#define xPSR_N_Pos 31U /*!< xPSR: N Position */ +#define xPSR_N_Msk (1UL << xPSR_N_Pos) /*!< xPSR: N Mask */ + +#define xPSR_Z_Pos 30U /*!< xPSR: Z Position */ +#define xPSR_Z_Msk (1UL << xPSR_Z_Pos) /*!< xPSR: Z Mask */ + +#define xPSR_C_Pos 29U /*!< xPSR: C Position */ +#define xPSR_C_Msk (1UL << xPSR_C_Pos) /*!< xPSR: C Mask */ + +#define xPSR_V_Pos 28U /*!< xPSR: V Position */ +#define xPSR_V_Msk (1UL << xPSR_V_Pos) /*!< xPSR: V Mask */ + +#define xPSR_Q_Pos 27U /*!< xPSR: Q Position */ +#define xPSR_Q_Msk (1UL << xPSR_Q_Pos) /*!< xPSR: Q Mask */ + +#define xPSR_IT_Pos 25U /*!< xPSR: IT Position */ +#define xPSR_IT_Msk (3UL << xPSR_IT_Pos) /*!< xPSR: IT Mask */ + +#define xPSR_T_Pos 24U /*!< xPSR: T Position */ +#define xPSR_T_Msk (1UL << xPSR_T_Pos) /*!< xPSR: T Mask */ + +#define xPSR_GE_Pos 16U /*!< xPSR: GE Position */ +#define xPSR_GE_Msk (0xFUL << xPSR_GE_Pos) /*!< xPSR: GE Mask */ + +#define xPSR_ISR_Pos 0U /*!< xPSR: ISR Position */ +#define xPSR_ISR_Msk (0x1FFUL /*<< xPSR_ISR_Pos*/) /*!< xPSR: ISR Mask */ + + +/** + \brief Union type to access the Control Registers (CONTROL). + */ +typedef union +{ + struct + { + uint32_t nPRIV: 1; /*!< bit: 0 Execution privilege in Thread mode */ + uint32_t SPSEL: 1; /*!< bit: 1 Stack-pointer select */ + uint32_t FPCA: 1; /*!< bit: 2 Floating-point context active */ + uint32_t SFPA: 1; /*!< bit: 3 Secure floating-point active */ + uint32_t _reserved1: 28; /*!< bit: 4..31 Reserved */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} CONTROL_Type; + +/* CONTROL Register Definitions */ +#define CONTROL_SFPA_Pos 3U /*!< CONTROL: SFPA Position */ +#define CONTROL_SFPA_Msk (1UL << CONTROL_SFPA_Pos) /*!< CONTROL: SFPA Mask */ + +#define CONTROL_FPCA_Pos 2U /*!< CONTROL: FPCA Position */ +#define CONTROL_FPCA_Msk (1UL << CONTROL_FPCA_Pos) /*!< CONTROL: FPCA Mask */ + +#define CONTROL_SPSEL_Pos 1U /*!< CONTROL: SPSEL Position */ +#define CONTROL_SPSEL_Msk (1UL << CONTROL_SPSEL_Pos) /*!< CONTROL: SPSEL Mask */ + +#define CONTROL_nPRIV_Pos 0U /*!< CONTROL: nPRIV Position */ +#define CONTROL_nPRIV_Msk (1UL /*<< CONTROL_nPRIV_Pos*/) /*!< CONTROL: nPRIV Mask */ + +/*@} end of group CMSIS_CORE */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_NVIC Nested Vectored Interrupt Controller (NVIC) + \brief Type definitions for the NVIC Registers + @{ + */ + +/** + \brief Structure type to access the Nested Vectored Interrupt Controller (NVIC). + */ +typedef struct +{ + __IOM uint32_t ISER[16U]; /*!< Offset: 0x000 (R/W) Interrupt Set Enable Register */ + uint32_t RESERVED0[16U]; + __IOM uint32_t ICER[16U]; /*!< Offset: 0x080 (R/W) Interrupt Clear Enable Register */ + uint32_t RSERVED1[16U]; + __IOM uint32_t ISPR[16U]; /*!< Offset: 0x100 (R/W) Interrupt Set Pending Register */ + uint32_t RESERVED2[16U]; + __IOM uint32_t ICPR[16U]; /*!< Offset: 0x180 (R/W) Interrupt Clear Pending Register */ + uint32_t RESERVED3[16U]; + __IOM uint32_t IABR[16U]; /*!< Offset: 0x200 (R/W) Interrupt Active bit Register */ + uint32_t RESERVED4[16U]; + __IOM uint32_t ITNS[16U]; /*!< Offset: 0x280 (R/W) Interrupt Non-Secure State Register */ + uint32_t RESERVED5[16U]; + __IOM uint8_t IPR[496U]; /*!< Offset: 0x300 (R/W) Interrupt Priority Register (8Bit wide) */ + uint32_t RESERVED6[580U]; + __OM uint32_t STIR; /*!< Offset: 0xE00 ( /W) Software Trigger Interrupt Register */ +} NVIC_Type; + +/* Software Triggered Interrupt Register Definitions */ +#define NVIC_STIR_INTID_Pos 0U /*!< STIR: INTLINESNUM Position */ +#define NVIC_STIR_INTID_Msk (0x1FFUL /*<< NVIC_STIR_INTID_Pos*/) /*!< STIR: INTLINESNUM Mask */ + +/*@} end of group CMSIS_NVIC */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SCB System Control Block (SCB) + \brief Type definitions for the System Control Block Registers + @{ + */ + +/** + \brief Structure type to access the System Control Block (SCB). + */ +typedef struct +{ + __IM uint32_t CPUID; /*!< Offset: 0x000 (R/ ) CPUID Base Register */ + __IOM uint32_t ICSR; /*!< Offset: 0x004 (R/W) Interrupt Control and State Register */ + __IOM uint32_t VTOR; /*!< Offset: 0x008 (R/W) Vector Table Offset Register */ + __IOM uint32_t AIRCR; /*!< Offset: 0x00C (R/W) Application Interrupt and Reset Control Register */ + __IOM uint32_t SCR; /*!< Offset: 0x010 (R/W) System Control Register */ + __IOM uint32_t CCR; /*!< Offset: 0x014 (R/W) Configuration Control Register */ + __IOM uint8_t SHPR[12U]; /*!< Offset: 0x018 (R/W) System Handlers Priority Registers (4-7, 8-11, 12-15) */ + __IOM uint32_t SHCSR; /*!< Offset: 0x024 (R/W) System Handler Control and State Register */ + __IOM uint32_t CFSR; /*!< Offset: 0x028 (R/W) Configurable Fault Status Register */ + __IOM uint32_t HFSR; /*!< Offset: 0x02C (R/W) HardFault Status Register */ + __IOM uint32_t DFSR; /*!< Offset: 0x030 (R/W) Debug Fault Status Register */ + __IOM uint32_t MMFAR; /*!< Offset: 0x034 (R/W) MemManage Fault Address Register */ + __IOM uint32_t BFAR; /*!< Offset: 0x038 (R/W) BusFault Address Register */ + __IOM uint32_t AFSR; /*!< Offset: 0x03C (R/W) Auxiliary Fault Status Register */ + __IM uint32_t ID_PFR[2U]; /*!< Offset: 0x040 (R/ ) Processor Feature Register */ + __IM uint32_t ID_DFR; /*!< Offset: 0x048 (R/ ) Debug Feature Register */ + __IM uint32_t ID_ADR; /*!< Offset: 0x04C (R/ ) Auxiliary Feature Register */ + __IM uint32_t ID_MMFR[4U]; /*!< Offset: 0x050 (R/ ) Memory Model Feature Register */ + __IM uint32_t ID_ISAR[6U]; /*!< Offset: 0x060 (R/ ) Instruction Set Attributes Register */ + __IM uint32_t CLIDR; /*!< Offset: 0x078 (R/ ) Cache Level ID register */ + __IM uint32_t CTR; /*!< Offset: 0x07C (R/ ) Cache Type register */ + __IM uint32_t CCSIDR; /*!< Offset: 0x080 (R/ ) Cache Size ID Register */ + __IOM uint32_t CSSELR; /*!< Offset: 0x084 (R/W) Cache Size Selection Register */ + __IOM uint32_t CPACR; /*!< Offset: 0x088 (R/W) Coprocessor Access Control Register */ + __IOM uint32_t NSACR; /*!< Offset: 0x08C (R/W) Non-Secure Access Control Register */ + uint32_t RESERVED3[92U]; + __OM uint32_t STIR; /*!< Offset: 0x200 ( /W) Software Triggered Interrupt Register */ + uint32_t RESERVED4[15U]; + __IM uint32_t MVFR0; /*!< Offset: 0x240 (R/ ) Media and VFP Feature Register 0 */ + __IM uint32_t MVFR1; /*!< Offset: 0x244 (R/ ) Media and VFP Feature Register 1 */ + __IM uint32_t MVFR2; /*!< Offset: 0x248 (R/ ) Media and VFP Feature Register 2 */ + uint32_t RESERVED5[1U]; + __OM uint32_t ICIALLU; /*!< Offset: 0x250 ( /W) I-Cache Invalidate All to PoU */ + uint32_t RESERVED6[1U]; + __OM uint32_t ICIMVAU; /*!< Offset: 0x258 ( /W) I-Cache Invalidate by MVA to PoU */ + __OM uint32_t DCIMVAC; /*!< Offset: 0x25C ( /W) D-Cache Invalidate by MVA to PoC */ + __OM uint32_t DCISW; /*!< Offset: 0x260 ( /W) D-Cache Invalidate by Set-way */ + __OM uint32_t DCCMVAU; /*!< Offset: 0x264 ( /W) D-Cache Clean by MVA to PoU */ + __OM uint32_t DCCMVAC; /*!< Offset: 0x268 ( /W) D-Cache Clean by MVA to PoC */ + __OM uint32_t DCCSW; /*!< Offset: 0x26C ( /W) D-Cache Clean by Set-way */ + __OM uint32_t DCCIMVAC; /*!< Offset: 0x270 ( /W) D-Cache Clean and Invalidate by MVA to PoC */ + __OM uint32_t DCCISW; /*!< Offset: 0x274 ( /W) D-Cache Clean and Invalidate by Set-way */ + uint32_t RESERVED7[6U]; + __IOM uint32_t ITCMCR; /*!< Offset: 0x290 (R/W) Instruction Tightly-Coupled Memory Control Register */ + __IOM uint32_t DTCMCR; /*!< Offset: 0x294 (R/W) Data Tightly-Coupled Memory Control Registers */ + __IOM uint32_t AHBPCR; /*!< Offset: 0x298 (R/W) AHBP Control Register */ + __IOM uint32_t CACR; /*!< Offset: 0x29C (R/W) L1 Cache Control Register */ + __IOM uint32_t AHBSCR; /*!< Offset: 0x2A0 (R/W) AHB Slave Control Register */ + uint32_t RESERVED8[1U]; + __IOM uint32_t ABFSR; /*!< Offset: 0x2A8 (R/W) Auxiliary Bus Fault Status Register */ +} SCB_Type; + +/* SCB CPUID Register Definitions */ +#define SCB_CPUID_IMPLEMENTER_Pos 24U /*!< SCB CPUID: IMPLEMENTER Position */ +#define SCB_CPUID_IMPLEMENTER_Msk (0xFFUL << SCB_CPUID_IMPLEMENTER_Pos) /*!< SCB CPUID: IMPLEMENTER Mask */ + +#define SCB_CPUID_VARIANT_Pos 20U /*!< SCB CPUID: VARIANT Position */ +#define SCB_CPUID_VARIANT_Msk (0xFUL << SCB_CPUID_VARIANT_Pos) /*!< SCB CPUID: VARIANT Mask */ + +#define SCB_CPUID_ARCHITECTURE_Pos 16U /*!< SCB CPUID: ARCHITECTURE Position */ +#define SCB_CPUID_ARCHITECTURE_Msk (0xFUL << SCB_CPUID_ARCHITECTURE_Pos) /*!< SCB CPUID: ARCHITECTURE Mask */ + +#define SCB_CPUID_PARTNO_Pos 4U /*!< SCB CPUID: PARTNO Position */ +#define SCB_CPUID_PARTNO_Msk (0xFFFUL << SCB_CPUID_PARTNO_Pos) /*!< SCB CPUID: PARTNO Mask */ + +#define SCB_CPUID_REVISION_Pos 0U /*!< SCB CPUID: REVISION Position */ +#define SCB_CPUID_REVISION_Msk (0xFUL /*<< SCB_CPUID_REVISION_Pos*/) /*!< SCB CPUID: REVISION Mask */ + +/* SCB Interrupt Control State Register Definitions */ +#define SCB_ICSR_PENDNMISET_Pos 31U /*!< SCB ICSR: PENDNMISET Position */ +#define SCB_ICSR_PENDNMISET_Msk (1UL << SCB_ICSR_PENDNMISET_Pos) /*!< SCB ICSR: PENDNMISET Mask */ + +#define SCB_ICSR_NMIPENDSET_Pos SCB_ICSR_PENDNMISET_Pos /*!< SCB ICSR: NMIPENDSET Position, backward compatibility */ +#define SCB_ICSR_NMIPENDSET_Msk SCB_ICSR_PENDNMISET_Msk /*!< SCB ICSR: NMIPENDSET Mask, backward compatibility */ + +#define SCB_ICSR_PENDNMICLR_Pos 30U /*!< SCB ICSR: PENDNMICLR Position */ +#define SCB_ICSR_PENDNMICLR_Msk (1UL << SCB_ICSR_PENDNMICLR_Pos) /*!< SCB ICSR: PENDNMICLR Mask */ + +#define SCB_ICSR_PENDSVSET_Pos 28U /*!< SCB ICSR: PENDSVSET Position */ +#define SCB_ICSR_PENDSVSET_Msk (1UL << SCB_ICSR_PENDSVSET_Pos) /*!< SCB ICSR: PENDSVSET Mask */ + +#define SCB_ICSR_PENDSVCLR_Pos 27U /*!< SCB ICSR: PENDSVCLR Position */ +#define SCB_ICSR_PENDSVCLR_Msk (1UL << SCB_ICSR_PENDSVCLR_Pos) /*!< SCB ICSR: PENDSVCLR Mask */ + +#define SCB_ICSR_PENDSTSET_Pos 26U /*!< SCB ICSR: PENDSTSET Position */ +#define SCB_ICSR_PENDSTSET_Msk (1UL << SCB_ICSR_PENDSTSET_Pos) /*!< SCB ICSR: PENDSTSET Mask */ + +#define SCB_ICSR_PENDSTCLR_Pos 25U /*!< SCB ICSR: PENDSTCLR Position */ +#define SCB_ICSR_PENDSTCLR_Msk (1UL << SCB_ICSR_PENDSTCLR_Pos) /*!< SCB ICSR: PENDSTCLR Mask */ + +#define SCB_ICSR_STTNS_Pos 24U /*!< SCB ICSR: STTNS Position (Security Extension) */ +#define SCB_ICSR_STTNS_Msk (1UL << SCB_ICSR_STTNS_Pos) /*!< SCB ICSR: STTNS Mask (Security Extension) */ + +#define SCB_ICSR_ISRPREEMPT_Pos 23U /*!< SCB ICSR: ISRPREEMPT Position */ +#define SCB_ICSR_ISRPREEMPT_Msk (1UL << SCB_ICSR_ISRPREEMPT_Pos) /*!< SCB ICSR: ISRPREEMPT Mask */ + +#define SCB_ICSR_ISRPENDING_Pos 22U /*!< SCB ICSR: ISRPENDING Position */ +#define SCB_ICSR_ISRPENDING_Msk (1UL << SCB_ICSR_ISRPENDING_Pos) /*!< SCB ICSR: ISRPENDING Mask */ + +#define SCB_ICSR_VECTPENDING_Pos 12U /*!< SCB ICSR: VECTPENDING Position */ +#define SCB_ICSR_VECTPENDING_Msk (0x1FFUL << SCB_ICSR_VECTPENDING_Pos) /*!< SCB ICSR: VECTPENDING Mask */ + +#define SCB_ICSR_RETTOBASE_Pos 11U /*!< SCB ICSR: RETTOBASE Position */ +#define SCB_ICSR_RETTOBASE_Msk (1UL << SCB_ICSR_RETTOBASE_Pos) /*!< SCB ICSR: RETTOBASE Mask */ + +#define SCB_ICSR_VECTACTIVE_Pos 0U /*!< SCB ICSR: VECTACTIVE Position */ +#define SCB_ICSR_VECTACTIVE_Msk (0x1FFUL /*<< SCB_ICSR_VECTACTIVE_Pos*/) /*!< SCB ICSR: VECTACTIVE Mask */ + +/* SCB Vector Table Offset Register Definitions */ +#define SCB_VTOR_TBLOFF_Pos 7U /*!< SCB VTOR: TBLOFF Position */ +#define SCB_VTOR_TBLOFF_Msk (0x1FFFFFFUL << SCB_VTOR_TBLOFF_Pos) /*!< SCB VTOR: TBLOFF Mask */ + +/* SCB Application Interrupt and Reset Control Register Definitions */ +#define SCB_AIRCR_VECTKEY_Pos 16U /*!< SCB AIRCR: VECTKEY Position */ +#define SCB_AIRCR_VECTKEY_Msk (0xFFFFUL << SCB_AIRCR_VECTKEY_Pos) /*!< SCB AIRCR: VECTKEY Mask */ + +#define SCB_AIRCR_VECTKEYSTAT_Pos 16U /*!< SCB AIRCR: VECTKEYSTAT Position */ +#define SCB_AIRCR_VECTKEYSTAT_Msk (0xFFFFUL << SCB_AIRCR_VECTKEYSTAT_Pos) /*!< SCB AIRCR: VECTKEYSTAT Mask */ + +#define SCB_AIRCR_ENDIANESS_Pos 15U /*!< SCB AIRCR: ENDIANESS Position */ +#define SCB_AIRCR_ENDIANESS_Msk (1UL << SCB_AIRCR_ENDIANESS_Pos) /*!< SCB AIRCR: ENDIANESS Mask */ + +#define SCB_AIRCR_PRIS_Pos 14U /*!< SCB AIRCR: PRIS Position */ +#define SCB_AIRCR_PRIS_Msk (1UL << SCB_AIRCR_PRIS_Pos) /*!< SCB AIRCR: PRIS Mask */ + +#define SCB_AIRCR_BFHFNMINS_Pos 13U /*!< SCB AIRCR: BFHFNMINS Position */ +#define SCB_AIRCR_BFHFNMINS_Msk (1UL << SCB_AIRCR_BFHFNMINS_Pos) /*!< SCB AIRCR: BFHFNMINS Mask */ + +#define SCB_AIRCR_PRIGROUP_Pos 8U /*!< SCB AIRCR: PRIGROUP Position */ +#define SCB_AIRCR_PRIGROUP_Msk (7UL << SCB_AIRCR_PRIGROUP_Pos) /*!< SCB AIRCR: PRIGROUP Mask */ + +#define SCB_AIRCR_SYSRESETREQS_Pos 3U /*!< SCB AIRCR: SYSRESETREQS Position */ +#define SCB_AIRCR_SYSRESETREQS_Msk (1UL << SCB_AIRCR_SYSRESETREQS_Pos) /*!< SCB AIRCR: SYSRESETREQS Mask */ + +#define SCB_AIRCR_SYSRESETREQ_Pos 2U /*!< SCB AIRCR: SYSRESETREQ Position */ +#define SCB_AIRCR_SYSRESETREQ_Msk (1UL << SCB_AIRCR_SYSRESETREQ_Pos) /*!< SCB AIRCR: SYSRESETREQ Mask */ + +#define SCB_AIRCR_VECTCLRACTIVE_Pos 1U /*!< SCB AIRCR: VECTCLRACTIVE Position */ +#define SCB_AIRCR_VECTCLRACTIVE_Msk (1UL << SCB_AIRCR_VECTCLRACTIVE_Pos) /*!< SCB AIRCR: VECTCLRACTIVE Mask */ + +/* SCB System Control Register Definitions */ +#define SCB_SCR_SEVONPEND_Pos 4U /*!< SCB SCR: SEVONPEND Position */ +#define SCB_SCR_SEVONPEND_Msk (1UL << SCB_SCR_SEVONPEND_Pos) /*!< SCB SCR: SEVONPEND Mask */ + +#define SCB_SCR_SLEEPDEEPS_Pos 3U /*!< SCB SCR: SLEEPDEEPS Position */ +#define SCB_SCR_SLEEPDEEPS_Msk (1UL << SCB_SCR_SLEEPDEEPS_Pos) /*!< SCB SCR: SLEEPDEEPS Mask */ + +#define SCB_SCR_SLEEPDEEP_Pos 2U /*!< SCB SCR: SLEEPDEEP Position */ +#define SCB_SCR_SLEEPDEEP_Msk (1UL << SCB_SCR_SLEEPDEEP_Pos) /*!< SCB SCR: SLEEPDEEP Mask */ + +#define SCB_SCR_SLEEPONEXIT_Pos 1U /*!< SCB SCR: SLEEPONEXIT Position */ +#define SCB_SCR_SLEEPONEXIT_Msk (1UL << SCB_SCR_SLEEPONEXIT_Pos) /*!< SCB SCR: SLEEPONEXIT Mask */ + +/* SCB Configuration Control Register Definitions */ +#define SCB_CCR_BP_Pos 18U /*!< SCB CCR: BP Position */ +#define SCB_CCR_BP_Msk (1UL << SCB_CCR_BP_Pos) /*!< SCB CCR: BP Mask */ + +#define SCB_CCR_IC_Pos 17U /*!< SCB CCR: IC Position */ +#define SCB_CCR_IC_Msk (1UL << SCB_CCR_IC_Pos) /*!< SCB CCR: IC Mask */ + +#define SCB_CCR_DC_Pos 16U /*!< SCB CCR: DC Position */ +#define SCB_CCR_DC_Msk (1UL << SCB_CCR_DC_Pos) /*!< SCB CCR: DC Mask */ + +#define SCB_CCR_STKOFHFNMIGN_Pos 10U /*!< SCB CCR: STKOFHFNMIGN Position */ +#define SCB_CCR_STKOFHFNMIGN_Msk (1UL << SCB_CCR_STKOFHFNMIGN_Pos) /*!< SCB CCR: STKOFHFNMIGN Mask */ + +#define SCB_CCR_BFHFNMIGN_Pos 8U /*!< SCB CCR: BFHFNMIGN Position */ +#define SCB_CCR_BFHFNMIGN_Msk (1UL << SCB_CCR_BFHFNMIGN_Pos) /*!< SCB CCR: BFHFNMIGN Mask */ + +#define SCB_CCR_DIV_0_TRP_Pos 4U /*!< SCB CCR: DIV_0_TRP Position */ +#define SCB_CCR_DIV_0_TRP_Msk (1UL << SCB_CCR_DIV_0_TRP_Pos) /*!< SCB CCR: DIV_0_TRP Mask */ + +#define SCB_CCR_UNALIGN_TRP_Pos 3U /*!< SCB CCR: UNALIGN_TRP Position */ +#define SCB_CCR_UNALIGN_TRP_Msk (1UL << SCB_CCR_UNALIGN_TRP_Pos) /*!< SCB CCR: UNALIGN_TRP Mask */ + +#define SCB_CCR_USERSETMPEND_Pos 1U /*!< SCB CCR: USERSETMPEND Position */ +#define SCB_CCR_USERSETMPEND_Msk (1UL << SCB_CCR_USERSETMPEND_Pos) /*!< SCB CCR: USERSETMPEND Mask */ + +/* SCB System Handler Control and State Register Definitions */ +#define SCB_SHCSR_HARDFAULTPENDED_Pos 21U /*!< SCB SHCSR: HARDFAULTPENDED Position */ +#define SCB_SHCSR_HARDFAULTPENDED_Msk (1UL << SCB_SHCSR_HARDFAULTPENDED_Pos) /*!< SCB SHCSR: HARDFAULTPENDED Mask */ + +#define SCB_SHCSR_SECUREFAULTPENDED_Pos 20U /*!< SCB SHCSR: SECUREFAULTPENDED Position */ +#define SCB_SHCSR_SECUREFAULTPENDED_Msk (1UL << SCB_SHCSR_SECUREFAULTPENDED_Pos) /*!< SCB SHCSR: SECUREFAULTPENDED Mask */ + +#define SCB_SHCSR_SECUREFAULTENA_Pos 19U /*!< SCB SHCSR: SECUREFAULTENA Position */ +#define SCB_SHCSR_SECUREFAULTENA_Msk (1UL << SCB_SHCSR_SECUREFAULTENA_Pos) /*!< SCB SHCSR: SECUREFAULTENA Mask */ + +#define SCB_SHCSR_USGFAULTENA_Pos 18U /*!< SCB SHCSR: USGFAULTENA Position */ +#define SCB_SHCSR_USGFAULTENA_Msk (1UL << SCB_SHCSR_USGFAULTENA_Pos) /*!< SCB SHCSR: USGFAULTENA Mask */ + +#define SCB_SHCSR_BUSFAULTENA_Pos 17U /*!< SCB SHCSR: BUSFAULTENA Position */ +#define SCB_SHCSR_BUSFAULTENA_Msk (1UL << SCB_SHCSR_BUSFAULTENA_Pos) /*!< SCB SHCSR: BUSFAULTENA Mask */ + +#define SCB_SHCSR_MEMFAULTENA_Pos 16U /*!< SCB SHCSR: MEMFAULTENA Position */ +#define SCB_SHCSR_MEMFAULTENA_Msk (1UL << SCB_SHCSR_MEMFAULTENA_Pos) /*!< SCB SHCSR: MEMFAULTENA Mask */ + +#define SCB_SHCSR_SVCALLPENDED_Pos 15U /*!< SCB SHCSR: SVCALLPENDED Position */ +#define SCB_SHCSR_SVCALLPENDED_Msk (1UL << SCB_SHCSR_SVCALLPENDED_Pos) /*!< SCB SHCSR: SVCALLPENDED Mask */ + +#define SCB_SHCSR_BUSFAULTPENDED_Pos 14U /*!< SCB SHCSR: BUSFAULTPENDED Position */ +#define SCB_SHCSR_BUSFAULTPENDED_Msk (1UL << SCB_SHCSR_BUSFAULTPENDED_Pos) /*!< SCB SHCSR: BUSFAULTPENDED Mask */ + +#define SCB_SHCSR_MEMFAULTPENDED_Pos 13U /*!< SCB SHCSR: MEMFAULTPENDED Position */ +#define SCB_SHCSR_MEMFAULTPENDED_Msk (1UL << SCB_SHCSR_MEMFAULTPENDED_Pos) /*!< SCB SHCSR: MEMFAULTPENDED Mask */ + +#define SCB_SHCSR_USGFAULTPENDED_Pos 12U /*!< SCB SHCSR: USGFAULTPENDED Position */ +#define SCB_SHCSR_USGFAULTPENDED_Msk (1UL << SCB_SHCSR_USGFAULTPENDED_Pos) /*!< SCB SHCSR: USGFAULTPENDED Mask */ + +#define SCB_SHCSR_SYSTICKACT_Pos 11U /*!< SCB SHCSR: SYSTICKACT Position */ +#define SCB_SHCSR_SYSTICKACT_Msk (1UL << SCB_SHCSR_SYSTICKACT_Pos) /*!< SCB SHCSR: SYSTICKACT Mask */ + +#define SCB_SHCSR_PENDSVACT_Pos 10U /*!< SCB SHCSR: PENDSVACT Position */ +#define SCB_SHCSR_PENDSVACT_Msk (1UL << SCB_SHCSR_PENDSVACT_Pos) /*!< SCB SHCSR: PENDSVACT Mask */ + +#define SCB_SHCSR_MONITORACT_Pos 8U /*!< SCB SHCSR: MONITORACT Position */ +#define SCB_SHCSR_MONITORACT_Msk (1UL << SCB_SHCSR_MONITORACT_Pos) /*!< SCB SHCSR: MONITORACT Mask */ + +#define SCB_SHCSR_SVCALLACT_Pos 7U /*!< SCB SHCSR: SVCALLACT Position */ +#define SCB_SHCSR_SVCALLACT_Msk (1UL << SCB_SHCSR_SVCALLACT_Pos) /*!< SCB SHCSR: SVCALLACT Mask */ + +#define SCB_SHCSR_NMIACT_Pos 5U /*!< SCB SHCSR: NMIACT Position */ +#define SCB_SHCSR_NMIACT_Msk (1UL << SCB_SHCSR_NMIACT_Pos) /*!< SCB SHCSR: NMIACT Mask */ + +#define SCB_SHCSR_SECUREFAULTACT_Pos 4U /*!< SCB SHCSR: SECUREFAULTACT Position */ +#define SCB_SHCSR_SECUREFAULTACT_Msk (1UL << SCB_SHCSR_SECUREFAULTACT_Pos) /*!< SCB SHCSR: SECUREFAULTACT Mask */ + +#define SCB_SHCSR_USGFAULTACT_Pos 3U /*!< SCB SHCSR: USGFAULTACT Position */ +#define SCB_SHCSR_USGFAULTACT_Msk (1UL << SCB_SHCSR_USGFAULTACT_Pos) /*!< SCB SHCSR: USGFAULTACT Mask */ + +#define SCB_SHCSR_HARDFAULTACT_Pos 2U /*!< SCB SHCSR: HARDFAULTACT Position */ +#define SCB_SHCSR_HARDFAULTACT_Msk (1UL << SCB_SHCSR_HARDFAULTACT_Pos) /*!< SCB SHCSR: HARDFAULTACT Mask */ + +#define SCB_SHCSR_BUSFAULTACT_Pos 1U /*!< SCB SHCSR: BUSFAULTACT Position */ +#define SCB_SHCSR_BUSFAULTACT_Msk (1UL << SCB_SHCSR_BUSFAULTACT_Pos) /*!< SCB SHCSR: BUSFAULTACT Mask */ + +#define SCB_SHCSR_MEMFAULTACT_Pos 0U /*!< SCB SHCSR: MEMFAULTACT Position */ +#define SCB_SHCSR_MEMFAULTACT_Msk (1UL /*<< SCB_SHCSR_MEMFAULTACT_Pos*/) /*!< SCB SHCSR: MEMFAULTACT Mask */ + +/* SCB Configurable Fault Status Register Definitions */ +#define SCB_CFSR_USGFAULTSR_Pos 16U /*!< SCB CFSR: Usage Fault Status Register Position */ +#define SCB_CFSR_USGFAULTSR_Msk (0xFFFFUL << SCB_CFSR_USGFAULTSR_Pos) /*!< SCB CFSR: Usage Fault Status Register Mask */ + +#define SCB_CFSR_BUSFAULTSR_Pos 8U /*!< SCB CFSR: Bus Fault Status Register Position */ +#define SCB_CFSR_BUSFAULTSR_Msk (0xFFUL << SCB_CFSR_BUSFAULTSR_Pos) /*!< SCB CFSR: Bus Fault Status Register Mask */ + +#define SCB_CFSR_MEMFAULTSR_Pos 0U /*!< SCB CFSR: Memory Manage Fault Status Register Position */ +#define SCB_CFSR_MEMFAULTSR_Msk (0xFFUL /*<< SCB_CFSR_MEMFAULTSR_Pos*/) /*!< SCB CFSR: Memory Manage Fault Status Register Mask */ + +/* MemManage Fault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_MMARVALID_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 7U) /*!< SCB CFSR (MMFSR): MMARVALID Position */ +#define SCB_CFSR_MMARVALID_Msk (1UL << SCB_CFSR_MMARVALID_Pos) /*!< SCB CFSR (MMFSR): MMARVALID Mask */ + +#define SCB_CFSR_MLSPERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 5U) /*!< SCB CFSR (MMFSR): MLSPERR Position */ +#define SCB_CFSR_MLSPERR_Msk (1UL << SCB_CFSR_MLSPERR_Pos) /*!< SCB CFSR (MMFSR): MLSPERR Mask */ + +#define SCB_CFSR_MSTKERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 4U) /*!< SCB CFSR (MMFSR): MSTKERR Position */ +#define SCB_CFSR_MSTKERR_Msk (1UL << SCB_CFSR_MSTKERR_Pos) /*!< SCB CFSR (MMFSR): MSTKERR Mask */ + +#define SCB_CFSR_MUNSTKERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 3U) /*!< SCB CFSR (MMFSR): MUNSTKERR Position */ +#define SCB_CFSR_MUNSTKERR_Msk (1UL << SCB_CFSR_MUNSTKERR_Pos) /*!< SCB CFSR (MMFSR): MUNSTKERR Mask */ + +#define SCB_CFSR_DACCVIOL_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 1U) /*!< SCB CFSR (MMFSR): DACCVIOL Position */ +#define SCB_CFSR_DACCVIOL_Msk (1UL << SCB_CFSR_DACCVIOL_Pos) /*!< SCB CFSR (MMFSR): DACCVIOL Mask */ + +#define SCB_CFSR_IACCVIOL_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 0U) /*!< SCB CFSR (MMFSR): IACCVIOL Position */ +#define SCB_CFSR_IACCVIOL_Msk (1UL /*<< SCB_CFSR_IACCVIOL_Pos*/) /*!< SCB CFSR (MMFSR): IACCVIOL Mask */ + +/* BusFault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_BFARVALID_Pos (SCB_CFSR_BUSFAULTSR_Pos + 7U) /*!< SCB CFSR (BFSR): BFARVALID Position */ +#define SCB_CFSR_BFARVALID_Msk (1UL << SCB_CFSR_BFARVALID_Pos) /*!< SCB CFSR (BFSR): BFARVALID Mask */ + +#define SCB_CFSR_LSPERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 5U) /*!< SCB CFSR (BFSR): LSPERR Position */ +#define SCB_CFSR_LSPERR_Msk (1UL << SCB_CFSR_LSPERR_Pos) /*!< SCB CFSR (BFSR): LSPERR Mask */ + +#define SCB_CFSR_STKERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 4U) /*!< SCB CFSR (BFSR): STKERR Position */ +#define SCB_CFSR_STKERR_Msk (1UL << SCB_CFSR_STKERR_Pos) /*!< SCB CFSR (BFSR): STKERR Mask */ + +#define SCB_CFSR_UNSTKERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 3U) /*!< SCB CFSR (BFSR): UNSTKERR Position */ +#define SCB_CFSR_UNSTKERR_Msk (1UL << SCB_CFSR_UNSTKERR_Pos) /*!< SCB CFSR (BFSR): UNSTKERR Mask */ + +#define SCB_CFSR_IMPRECISERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 2U) /*!< SCB CFSR (BFSR): IMPRECISERR Position */ +#define SCB_CFSR_IMPRECISERR_Msk (1UL << SCB_CFSR_IMPRECISERR_Pos) /*!< SCB CFSR (BFSR): IMPRECISERR Mask */ + +#define SCB_CFSR_PRECISERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 1U) /*!< SCB CFSR (BFSR): PRECISERR Position */ +#define SCB_CFSR_PRECISERR_Msk (1UL << SCB_CFSR_PRECISERR_Pos) /*!< SCB CFSR (BFSR): PRECISERR Mask */ + +#define SCB_CFSR_IBUSERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 0U) /*!< SCB CFSR (BFSR): IBUSERR Position */ +#define SCB_CFSR_IBUSERR_Msk (1UL << SCB_CFSR_IBUSERR_Pos) /*!< SCB CFSR (BFSR): IBUSERR Mask */ + +/* UsageFault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_DIVBYZERO_Pos (SCB_CFSR_USGFAULTSR_Pos + 9U) /*!< SCB CFSR (UFSR): DIVBYZERO Position */ +#define SCB_CFSR_DIVBYZERO_Msk (1UL << SCB_CFSR_DIVBYZERO_Pos) /*!< SCB CFSR (UFSR): DIVBYZERO Mask */ + +#define SCB_CFSR_UNALIGNED_Pos (SCB_CFSR_USGFAULTSR_Pos + 8U) /*!< SCB CFSR (UFSR): UNALIGNED Position */ +#define SCB_CFSR_UNALIGNED_Msk (1UL << SCB_CFSR_UNALIGNED_Pos) /*!< SCB CFSR (UFSR): UNALIGNED Mask */ + +#define SCB_CFSR_STKOF_Pos (SCB_CFSR_USGFAULTSR_Pos + 4U) /*!< SCB CFSR (UFSR): STKOF Position */ +#define SCB_CFSR_STKOF_Msk (1UL << SCB_CFSR_STKOF_Pos) /*!< SCB CFSR (UFSR): STKOF Mask */ + +#define SCB_CFSR_NOCP_Pos (SCB_CFSR_USGFAULTSR_Pos + 3U) /*!< SCB CFSR (UFSR): NOCP Position */ +#define SCB_CFSR_NOCP_Msk (1UL << SCB_CFSR_NOCP_Pos) /*!< SCB CFSR (UFSR): NOCP Mask */ + +#define SCB_CFSR_INVPC_Pos (SCB_CFSR_USGFAULTSR_Pos + 2U) /*!< SCB CFSR (UFSR): INVPC Position */ +#define SCB_CFSR_INVPC_Msk (1UL << SCB_CFSR_INVPC_Pos) /*!< SCB CFSR (UFSR): INVPC Mask */ + +#define SCB_CFSR_INVSTATE_Pos (SCB_CFSR_USGFAULTSR_Pos + 1U) /*!< SCB CFSR (UFSR): INVSTATE Position */ +#define SCB_CFSR_INVSTATE_Msk (1UL << SCB_CFSR_INVSTATE_Pos) /*!< SCB CFSR (UFSR): INVSTATE Mask */ + +#define SCB_CFSR_UNDEFINSTR_Pos (SCB_CFSR_USGFAULTSR_Pos + 0U) /*!< SCB CFSR (UFSR): UNDEFINSTR Position */ +#define SCB_CFSR_UNDEFINSTR_Msk (1UL << SCB_CFSR_UNDEFINSTR_Pos) /*!< SCB CFSR (UFSR): UNDEFINSTR Mask */ + +/* SCB Hard Fault Status Register Definitions */ +#define SCB_HFSR_DEBUGEVT_Pos 31U /*!< SCB HFSR: DEBUGEVT Position */ +#define SCB_HFSR_DEBUGEVT_Msk (1UL << SCB_HFSR_DEBUGEVT_Pos) /*!< SCB HFSR: DEBUGEVT Mask */ + +#define SCB_HFSR_FORCED_Pos 30U /*!< SCB HFSR: FORCED Position */ +#define SCB_HFSR_FORCED_Msk (1UL << SCB_HFSR_FORCED_Pos) /*!< SCB HFSR: FORCED Mask */ + +#define SCB_HFSR_VECTTBL_Pos 1U /*!< SCB HFSR: VECTTBL Position */ +#define SCB_HFSR_VECTTBL_Msk (1UL << SCB_HFSR_VECTTBL_Pos) /*!< SCB HFSR: VECTTBL Mask */ + +/* SCB Debug Fault Status Register Definitions */ +#define SCB_DFSR_EXTERNAL_Pos 4U /*!< SCB DFSR: EXTERNAL Position */ +#define SCB_DFSR_EXTERNAL_Msk (1UL << SCB_DFSR_EXTERNAL_Pos) /*!< SCB DFSR: EXTERNAL Mask */ + +#define SCB_DFSR_VCATCH_Pos 3U /*!< SCB DFSR: VCATCH Position */ +#define SCB_DFSR_VCATCH_Msk (1UL << SCB_DFSR_VCATCH_Pos) /*!< SCB DFSR: VCATCH Mask */ + +#define SCB_DFSR_DWTTRAP_Pos 2U /*!< SCB DFSR: DWTTRAP Position */ +#define SCB_DFSR_DWTTRAP_Msk (1UL << SCB_DFSR_DWTTRAP_Pos) /*!< SCB DFSR: DWTTRAP Mask */ + +#define SCB_DFSR_BKPT_Pos 1U /*!< SCB DFSR: BKPT Position */ +#define SCB_DFSR_BKPT_Msk (1UL << SCB_DFSR_BKPT_Pos) /*!< SCB DFSR: BKPT Mask */ + +#define SCB_DFSR_HALTED_Pos 0U /*!< SCB DFSR: HALTED Position */ +#define SCB_DFSR_HALTED_Msk (1UL /*<< SCB_DFSR_HALTED_Pos*/) /*!< SCB DFSR: HALTED Mask */ + +/* SCB Non-Secure Access Control Register Definitions */ +#define SCB_NSACR_CP11_Pos 11U /*!< SCB NSACR: CP11 Position */ +#define SCB_NSACR_CP11_Msk (1UL << SCB_NSACR_CP11_Pos) /*!< SCB NSACR: CP11 Mask */ + +#define SCB_NSACR_CP10_Pos 10U /*!< SCB NSACR: CP10 Position */ +#define SCB_NSACR_CP10_Msk (1UL << SCB_NSACR_CP10_Pos) /*!< SCB NSACR: CP10 Mask */ + +#define SCB_NSACR_CPn_Pos 0U /*!< SCB NSACR: CPn Position */ +#define SCB_NSACR_CPn_Msk (1UL /*<< SCB_NSACR_CPn_Pos*/) /*!< SCB NSACR: CPn Mask */ + +/* SCB Cache Level ID Register Definitions */ +#define SCB_CLIDR_LOUU_Pos 27U /*!< SCB CLIDR: LoUU Position */ +#define SCB_CLIDR_LOUU_Msk (7UL << SCB_CLIDR_LOUU_Pos) /*!< SCB CLIDR: LoUU Mask */ + +#define SCB_CLIDR_LOC_Pos 24U /*!< SCB CLIDR: LoC Position */ +#define SCB_CLIDR_LOC_Msk (7UL << SCB_CLIDR_LOC_Pos) /*!< SCB CLIDR: LoC Mask */ + +/* SCB Cache Type Register Definitions */ +#define SCB_CTR_FORMAT_Pos 29U /*!< SCB CTR: Format Position */ +#define SCB_CTR_FORMAT_Msk (7UL << SCB_CTR_FORMAT_Pos) /*!< SCB CTR: Format Mask */ + +#define SCB_CTR_CWG_Pos 24U /*!< SCB CTR: CWG Position */ +#define SCB_CTR_CWG_Msk (0xFUL << SCB_CTR_CWG_Pos) /*!< SCB CTR: CWG Mask */ + +#define SCB_CTR_ERG_Pos 20U /*!< SCB CTR: ERG Position */ +#define SCB_CTR_ERG_Msk (0xFUL << SCB_CTR_ERG_Pos) /*!< SCB CTR: ERG Mask */ + +#define SCB_CTR_DMINLINE_Pos 16U /*!< SCB CTR: DminLine Position */ +#define SCB_CTR_DMINLINE_Msk (0xFUL << SCB_CTR_DMINLINE_Pos) /*!< SCB CTR: DminLine Mask */ + +#define SCB_CTR_IMINLINE_Pos 0U /*!< SCB CTR: ImInLine Position */ +#define SCB_CTR_IMINLINE_Msk (0xFUL /*<< SCB_CTR_IMINLINE_Pos*/) /*!< SCB CTR: ImInLine Mask */ + +/* SCB Cache Size ID Register Definitions */ +#define SCB_CCSIDR_WT_Pos 31U /*!< SCB CCSIDR: WT Position */ +#define SCB_CCSIDR_WT_Msk (1UL << SCB_CCSIDR_WT_Pos) /*!< SCB CCSIDR: WT Mask */ + +#define SCB_CCSIDR_WB_Pos 30U /*!< SCB CCSIDR: WB Position */ +#define SCB_CCSIDR_WB_Msk (1UL << SCB_CCSIDR_WB_Pos) /*!< SCB CCSIDR: WB Mask */ + +#define SCB_CCSIDR_RA_Pos 29U /*!< SCB CCSIDR: RA Position */ +#define SCB_CCSIDR_RA_Msk (1UL << SCB_CCSIDR_RA_Pos) /*!< SCB CCSIDR: RA Mask */ + +#define SCB_CCSIDR_WA_Pos 28U /*!< SCB CCSIDR: WA Position */ +#define SCB_CCSIDR_WA_Msk (1UL << SCB_CCSIDR_WA_Pos) /*!< SCB CCSIDR: WA Mask */ + +#define SCB_CCSIDR_NUMSETS_Pos 13U /*!< SCB CCSIDR: NumSets Position */ +#define SCB_CCSIDR_NUMSETS_Msk (0x7FFFUL << SCB_CCSIDR_NUMSETS_Pos) /*!< SCB CCSIDR: NumSets Mask */ + +#define SCB_CCSIDR_ASSOCIATIVITY_Pos 3U /*!< SCB CCSIDR: Associativity Position */ +#define SCB_CCSIDR_ASSOCIATIVITY_Msk (0x3FFUL << SCB_CCSIDR_ASSOCIATIVITY_Pos) /*!< SCB CCSIDR: Associativity Mask */ + +#define SCB_CCSIDR_LINESIZE_Pos 0U /*!< SCB CCSIDR: LineSize Position */ +#define SCB_CCSIDR_LINESIZE_Msk (7UL /*<< SCB_CCSIDR_LINESIZE_Pos*/) /*!< SCB CCSIDR: LineSize Mask */ + +/* SCB Cache Size Selection Register Definitions */ +#define SCB_CSSELR_LEVEL_Pos 1U /*!< SCB CSSELR: Level Position */ +#define SCB_CSSELR_LEVEL_Msk (7UL << SCB_CSSELR_LEVEL_Pos) /*!< SCB CSSELR: Level Mask */ + +#define SCB_CSSELR_IND_Pos 0U /*!< SCB CSSELR: InD Position */ +#define SCB_CSSELR_IND_Msk (1UL /*<< SCB_CSSELR_IND_Pos*/) /*!< SCB CSSELR: InD Mask */ + +/* SCB Software Triggered Interrupt Register Definitions */ +#define SCB_STIR_INTID_Pos 0U /*!< SCB STIR: INTID Position */ +#define SCB_STIR_INTID_Msk (0x1FFUL /*<< SCB_STIR_INTID_Pos*/) /*!< SCB STIR: INTID Mask */ + +/* SCB D-Cache Invalidate by Set-way Register Definitions */ +#define SCB_DCISW_WAY_Pos 30U /*!< SCB DCISW: Way Position */ +#define SCB_DCISW_WAY_Msk (3UL << SCB_DCISW_WAY_Pos) /*!< SCB DCISW: Way Mask */ + +#define SCB_DCISW_SET_Pos 5U /*!< SCB DCISW: Set Position */ +#define SCB_DCISW_SET_Msk (0x1FFUL << SCB_DCISW_SET_Pos) /*!< SCB DCISW: Set Mask */ + +/* SCB D-Cache Clean by Set-way Register Definitions */ +#define SCB_DCCSW_WAY_Pos 30U /*!< SCB DCCSW: Way Position */ +#define SCB_DCCSW_WAY_Msk (3UL << SCB_DCCSW_WAY_Pos) /*!< SCB DCCSW: Way Mask */ + +#define SCB_DCCSW_SET_Pos 5U /*!< SCB DCCSW: Set Position */ +#define SCB_DCCSW_SET_Msk (0x1FFUL << SCB_DCCSW_SET_Pos) /*!< SCB DCCSW: Set Mask */ + +/* SCB D-Cache Clean and Invalidate by Set-way Register Definitions */ +#define SCB_DCCISW_WAY_Pos 30U /*!< SCB DCCISW: Way Position */ +#define SCB_DCCISW_WAY_Msk (3UL << SCB_DCCISW_WAY_Pos) /*!< SCB DCCISW: Way Mask */ + +#define SCB_DCCISW_SET_Pos 5U /*!< SCB DCCISW: Set Position */ +#define SCB_DCCISW_SET_Msk (0x1FFUL << SCB_DCCISW_SET_Pos) /*!< SCB DCCISW: Set Mask */ + +/* Instruction Tightly-Coupled Memory Control Register Definitions */ +#define SCB_ITCMCR_SZ_Pos 3U /*!< SCB ITCMCR: SZ Position */ +#define SCB_ITCMCR_SZ_Msk (0xFUL << SCB_ITCMCR_SZ_Pos) /*!< SCB ITCMCR: SZ Mask */ + +#define SCB_ITCMCR_RETEN_Pos 2U /*!< SCB ITCMCR: RETEN Position */ +#define SCB_ITCMCR_RETEN_Msk (1UL << SCB_ITCMCR_RETEN_Pos) /*!< SCB ITCMCR: RETEN Mask */ + +#define SCB_ITCMCR_RMW_Pos 1U /*!< SCB ITCMCR: RMW Position */ +#define SCB_ITCMCR_RMW_Msk (1UL << SCB_ITCMCR_RMW_Pos) /*!< SCB ITCMCR: RMW Mask */ + +#define SCB_ITCMCR_EN_Pos 0U /*!< SCB ITCMCR: EN Position */ +#define SCB_ITCMCR_EN_Msk (1UL /*<< SCB_ITCMCR_EN_Pos*/) /*!< SCB ITCMCR: EN Mask */ + +/* Data Tightly-Coupled Memory Control Register Definitions */ +#define SCB_DTCMCR_SZ_Pos 3U /*!< SCB DTCMCR: SZ Position */ +#define SCB_DTCMCR_SZ_Msk (0xFUL << SCB_DTCMCR_SZ_Pos) /*!< SCB DTCMCR: SZ Mask */ + +#define SCB_DTCMCR_RETEN_Pos 2U /*!< SCB DTCMCR: RETEN Position */ +#define SCB_DTCMCR_RETEN_Msk (1UL << SCB_DTCMCR_RETEN_Pos) /*!< SCB DTCMCR: RETEN Mask */ + +#define SCB_DTCMCR_RMW_Pos 1U /*!< SCB DTCMCR: RMW Position */ +#define SCB_DTCMCR_RMW_Msk (1UL << SCB_DTCMCR_RMW_Pos) /*!< SCB DTCMCR: RMW Mask */ + +#define SCB_DTCMCR_EN_Pos 0U /*!< SCB DTCMCR: EN Position */ +#define SCB_DTCMCR_EN_Msk (1UL /*<< SCB_DTCMCR_EN_Pos*/) /*!< SCB DTCMCR: EN Mask */ + +/* AHBP Control Register Definitions */ +#define SCB_AHBPCR_SZ_Pos 1U /*!< SCB AHBPCR: SZ Position */ +#define SCB_AHBPCR_SZ_Msk (7UL << SCB_AHBPCR_SZ_Pos) /*!< SCB AHBPCR: SZ Mask */ + +#define SCB_AHBPCR_EN_Pos 0U /*!< SCB AHBPCR: EN Position */ +#define SCB_AHBPCR_EN_Msk (1UL /*<< SCB_AHBPCR_EN_Pos*/) /*!< SCB AHBPCR: EN Mask */ + +/* L1 Cache Control Register Definitions */ +#define SCB_CACR_FORCEWT_Pos 2U /*!< SCB CACR: FORCEWT Position */ +#define SCB_CACR_FORCEWT_Msk (1UL << SCB_CACR_FORCEWT_Pos) /*!< SCB CACR: FORCEWT Mask */ + +#define SCB_CACR_ECCEN_Pos 1U /*!< SCB CACR: ECCEN Position */ +#define SCB_CACR_ECCEN_Msk (1UL << SCB_CACR_ECCEN_Pos) /*!< SCB CACR: ECCEN Mask */ + +#define SCB_CACR_SIWT_Pos 0U /*!< SCB CACR: SIWT Position */ +#define SCB_CACR_SIWT_Msk (1UL /*<< SCB_CACR_SIWT_Pos*/) /*!< SCB CACR: SIWT Mask */ + +/* AHBS Control Register Definitions */ +#define SCB_AHBSCR_INITCOUNT_Pos 11U /*!< SCB AHBSCR: INITCOUNT Position */ +#define SCB_AHBSCR_INITCOUNT_Msk (0x1FUL << SCB_AHBPCR_INITCOUNT_Pos) /*!< SCB AHBSCR: INITCOUNT Mask */ + +#define SCB_AHBSCR_TPRI_Pos 2U /*!< SCB AHBSCR: TPRI Position */ +#define SCB_AHBSCR_TPRI_Msk (0x1FFUL << SCB_AHBPCR_TPRI_Pos) /*!< SCB AHBSCR: TPRI Mask */ + +#define SCB_AHBSCR_CTL_Pos 0U /*!< SCB AHBSCR: CTL Position*/ +#define SCB_AHBSCR_CTL_Msk (3UL /*<< SCB_AHBPCR_CTL_Pos*/) /*!< SCB AHBSCR: CTL Mask */ + +/* Auxiliary Bus Fault Status Register Definitions */ +#define SCB_ABFSR_AXIMTYPE_Pos 8U /*!< SCB ABFSR: AXIMTYPE Position*/ +#define SCB_ABFSR_AXIMTYPE_Msk (3UL << SCB_ABFSR_AXIMTYPE_Pos) /*!< SCB ABFSR: AXIMTYPE Mask */ + +#define SCB_ABFSR_EPPB_Pos 4U /*!< SCB ABFSR: EPPB Position*/ +#define SCB_ABFSR_EPPB_Msk (1UL << SCB_ABFSR_EPPB_Pos) /*!< SCB ABFSR: EPPB Mask */ + +#define SCB_ABFSR_AXIM_Pos 3U /*!< SCB ABFSR: AXIM Position*/ +#define SCB_ABFSR_AXIM_Msk (1UL << SCB_ABFSR_AXIM_Pos) /*!< SCB ABFSR: AXIM Mask */ + +#define SCB_ABFSR_AHBP_Pos 2U /*!< SCB ABFSR: AHBP Position*/ +#define SCB_ABFSR_AHBP_Msk (1UL << SCB_ABFSR_AHBP_Pos) /*!< SCB ABFSR: AHBP Mask */ + +#define SCB_ABFSR_DTCM_Pos 1U /*!< SCB ABFSR: DTCM Position*/ +#define SCB_ABFSR_DTCM_Msk (1UL << SCB_ABFSR_DTCM_Pos) /*!< SCB ABFSR: DTCM Mask */ + +#define SCB_ABFSR_ITCM_Pos 0U /*!< SCB ABFSR: ITCM Position*/ +#define SCB_ABFSR_ITCM_Msk (1UL /*<< SCB_ABFSR_ITCM_Pos*/) /*!< SCB ABFSR: ITCM Mask */ + +/*@} end of group CMSIS_SCB */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SCnSCB System Controls not in SCB (SCnSCB) + \brief Type definitions for the System Control and ID Register not in the SCB + @{ + */ + +/** + \brief Structure type to access the System Control and ID Register not in the SCB. + */ +typedef struct +{ + uint32_t RESERVED0[1U]; + __IM uint32_t ICTR; /*!< Offset: 0x004 (R/ ) Interrupt Controller Type Register */ + __IOM uint32_t ACTLR; /*!< Offset: 0x008 (R/W) Auxiliary Control Register */ + __IOM uint32_t CPPWR; /*!< Offset: 0x00C (R/W) Coprocessor Power Control Register */ +} SCnSCB_Type; + +/* Interrupt Controller Type Register Definitions */ +#define SCnSCB_ICTR_INTLINESNUM_Pos 0U /*!< ICTR: INTLINESNUM Position */ +#define SCnSCB_ICTR_INTLINESNUM_Msk (0xFUL /*<< SCnSCB_ICTR_INTLINESNUM_Pos*/) /*!< ICTR: INTLINESNUM Mask */ + +/*@} end of group CMSIS_SCnotSCB */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SysTick System Tick Timer (SysTick) + \brief Type definitions for the System Timer Registers. + @{ + */ + +/** + \brief Structure type to access the System Timer (SysTick). + */ +typedef struct +{ + __IOM uint32_t CTRL; /*!< Offset: 0x000 (R/W) SysTick Control and Status Register */ + __IOM uint32_t LOAD; /*!< Offset: 0x004 (R/W) SysTick Reload Value Register */ + __IOM uint32_t VAL; /*!< Offset: 0x008 (R/W) SysTick Current Value Register */ + __IM uint32_t CALIB; /*!< Offset: 0x00C (R/ ) SysTick Calibration Register */ +} SysTick_Type; + +/* SysTick Control / Status Register Definitions */ +#define SysTick_CTRL_COUNTFLAG_Pos 16U /*!< SysTick CTRL: COUNTFLAG Position */ +#define SysTick_CTRL_COUNTFLAG_Msk (1UL << SysTick_CTRL_COUNTFLAG_Pos) /*!< SysTick CTRL: COUNTFLAG Mask */ + +#define SysTick_CTRL_CLKSOURCE_Pos 2U /*!< SysTick CTRL: CLKSOURCE Position */ +#define SysTick_CTRL_CLKSOURCE_Msk (1UL << SysTick_CTRL_CLKSOURCE_Pos) /*!< SysTick CTRL: CLKSOURCE Mask */ + +#define SysTick_CTRL_TICKINT_Pos 1U /*!< SysTick CTRL: TICKINT Position */ +#define SysTick_CTRL_TICKINT_Msk (1UL << SysTick_CTRL_TICKINT_Pos) /*!< SysTick CTRL: TICKINT Mask */ + +#define SysTick_CTRL_ENABLE_Pos 0U /*!< SysTick CTRL: ENABLE Position */ +#define SysTick_CTRL_ENABLE_Msk (1UL /*<< SysTick_CTRL_ENABLE_Pos*/) /*!< SysTick CTRL: ENABLE Mask */ + +/* SysTick Reload Register Definitions */ +#define SysTick_LOAD_RELOAD_Pos 0U /*!< SysTick LOAD: RELOAD Position */ +#define SysTick_LOAD_RELOAD_Msk (0xFFFFFFUL /*<< SysTick_LOAD_RELOAD_Pos*/) /*!< SysTick LOAD: RELOAD Mask */ + +/* SysTick Current Register Definitions */ +#define SysTick_VAL_CURRENT_Pos 0U /*!< SysTick VAL: CURRENT Position */ +#define SysTick_VAL_CURRENT_Msk (0xFFFFFFUL /*<< SysTick_VAL_CURRENT_Pos*/) /*!< SysTick VAL: CURRENT Mask */ + +/* SysTick Calibration Register Definitions */ +#define SysTick_CALIB_NOREF_Pos 31U /*!< SysTick CALIB: NOREF Position */ +#define SysTick_CALIB_NOREF_Msk (1UL << SysTick_CALIB_NOREF_Pos) /*!< SysTick CALIB: NOREF Mask */ + +#define SysTick_CALIB_SKEW_Pos 30U /*!< SysTick CALIB: SKEW Position */ +#define SysTick_CALIB_SKEW_Msk (1UL << SysTick_CALIB_SKEW_Pos) /*!< SysTick CALIB: SKEW Mask */ + +#define SysTick_CALIB_TENMS_Pos 0U /*!< SysTick CALIB: TENMS Position */ +#define SysTick_CALIB_TENMS_Msk (0xFFFFFFUL /*<< SysTick_CALIB_TENMS_Pos*/) /*!< SysTick CALIB: TENMS Mask */ + +/*@} end of group CMSIS_SysTick */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_ITM Instrumentation Trace Macrocell (ITM) + \brief Type definitions for the Instrumentation Trace Macrocell (ITM) + @{ + */ + +/** + \brief Structure type to access the Instrumentation Trace Macrocell Register (ITM). + */ +typedef struct +{ + __OM union + { + __OM uint8_t u8; /*!< Offset: 0x000 ( /W) ITM Stimulus Port 8-bit */ + __OM uint16_t u16; /*!< Offset: 0x000 ( /W) ITM Stimulus Port 16-bit */ + __OM uint32_t u32; /*!< Offset: 0x000 ( /W) ITM Stimulus Port 32-bit */ + } PORT [32U]; /*!< Offset: 0x000 ( /W) ITM Stimulus Port Registers */ + uint32_t RESERVED0[864U]; + __IOM uint32_t TER; /*!< Offset: 0xE00 (R/W) ITM Trace Enable Register */ + uint32_t RESERVED1[15U]; + __IOM uint32_t TPR; /*!< Offset: 0xE40 (R/W) ITM Trace Privilege Register */ + uint32_t RESERVED2[15U]; + __IOM uint32_t TCR; /*!< Offset: 0xE80 (R/W) ITM Trace Control Register */ + uint32_t RESERVED3[29U]; + __OM uint32_t IWR; /*!< Offset: 0xEF8 ( /W) ITM Integration Write Register */ + __IM uint32_t IRR; /*!< Offset: 0xEFC (R/ ) ITM Integration Read Register */ + __IOM uint32_t IMCR; /*!< Offset: 0xF00 (R/W) ITM Integration Mode Control Register */ + uint32_t RESERVED4[43U]; + __OM uint32_t LAR; /*!< Offset: 0xFB0 ( /W) ITM Lock Access Register */ + __IM uint32_t LSR; /*!< Offset: 0xFB4 (R/ ) ITM Lock Status Register */ + uint32_t RESERVED5[1U]; + __IM uint32_t DEVARCH; /*!< Offset: 0xFBC (R/ ) ITM Device Architecture Register */ + uint32_t RESERVED6[4U]; + __IM uint32_t PID4; /*!< Offset: 0xFD0 (R/ ) ITM Peripheral Identification Register #4 */ + __IM uint32_t PID5; /*!< Offset: 0xFD4 (R/ ) ITM Peripheral Identification Register #5 */ + __IM uint32_t PID6; /*!< Offset: 0xFD8 (R/ ) ITM Peripheral Identification Register #6 */ + __IM uint32_t PID7; /*!< Offset: 0xFDC (R/ ) ITM Peripheral Identification Register #7 */ + __IM uint32_t PID0; /*!< Offset: 0xFE0 (R/ ) ITM Peripheral Identification Register #0 */ + __IM uint32_t PID1; /*!< Offset: 0xFE4 (R/ ) ITM Peripheral Identification Register #1 */ + __IM uint32_t PID2; /*!< Offset: 0xFE8 (R/ ) ITM Peripheral Identification Register #2 */ + __IM uint32_t PID3; /*!< Offset: 0xFEC (R/ ) ITM Peripheral Identification Register #3 */ + __IM uint32_t CID0; /*!< Offset: 0xFF0 (R/ ) ITM Component Identification Register #0 */ + __IM uint32_t CID1; /*!< Offset: 0xFF4 (R/ ) ITM Component Identification Register #1 */ + __IM uint32_t CID2; /*!< Offset: 0xFF8 (R/ ) ITM Component Identification Register #2 */ + __IM uint32_t CID3; /*!< Offset: 0xFFC (R/ ) ITM Component Identification Register #3 */ +} ITM_Type; + +/* ITM Stimulus Port Register Definitions */ +#define ITM_STIM_DISABLED_Pos 1U /*!< ITM STIM: DISABLED Position */ +#define ITM_STIM_DISABLED_Msk (0x1UL << ITM_STIM_DISABLED_Pos) /*!< ITM STIM: DISABLED Mask */ + +#define ITM_STIM_FIFOREADY_Pos 0U /*!< ITM STIM: FIFOREADY Position */ +#define ITM_STIM_FIFOREADY_Msk (0x1UL /*<< ITM_STIM_FIFOREADY_Pos*/) /*!< ITM STIM: FIFOREADY Mask */ + +/* ITM Trace Privilege Register Definitions */ +#define ITM_TPR_PRIVMASK_Pos 0U /*!< ITM TPR: PRIVMASK Position */ +#define ITM_TPR_PRIVMASK_Msk (0xFUL /*<< ITM_TPR_PRIVMASK_Pos*/) /*!< ITM TPR: PRIVMASK Mask */ + +/* ITM Trace Control Register Definitions */ +#define ITM_TCR_BUSY_Pos 23U /*!< ITM TCR: BUSY Position */ +#define ITM_TCR_BUSY_Msk (1UL << ITM_TCR_BUSY_Pos) /*!< ITM TCR: BUSY Mask */ + +#define ITM_TCR_TRACEBUSID_Pos 16U /*!< ITM TCR: ATBID Position */ +#define ITM_TCR_TRACEBUSID_Msk (0x7FUL << ITM_TCR_TRACEBUSID_Pos) /*!< ITM TCR: ATBID Mask */ + +#define ITM_TCR_GTSFREQ_Pos 10U /*!< ITM TCR: Global timestamp frequency Position */ +#define ITM_TCR_GTSFREQ_Msk (3UL << ITM_TCR_GTSFREQ_Pos) /*!< ITM TCR: Global timestamp frequency Mask */ + +#define ITM_TCR_TSPRESCALE_Pos 8U /*!< ITM TCR: TSPRESCALE Position */ +#define ITM_TCR_TSPRESCALE_Msk (3UL << ITM_TCR_TSPRESCALE_Pos) /*!< ITM TCR: TSPRESCALE Mask */ + +#define ITM_TCR_STALLENA_Pos 5U /*!< ITM TCR: STALLENA Position */ +#define ITM_TCR_STALLENA_Msk (1UL << ITM_TCR_STALLENA_Pos) /*!< ITM TCR: STALLENA Mask */ + +#define ITM_TCR_SWOENA_Pos 4U /*!< ITM TCR: SWOENA Position */ +#define ITM_TCR_SWOENA_Msk (1UL << ITM_TCR_SWOENA_Pos) /*!< ITM TCR: SWOENA Mask */ + +#define ITM_TCR_DWTENA_Pos 3U /*!< ITM TCR: DWTENA Position */ +#define ITM_TCR_DWTENA_Msk (1UL << ITM_TCR_DWTENA_Pos) /*!< ITM TCR: DWTENA Mask */ + +#define ITM_TCR_SYNCENA_Pos 2U /*!< ITM TCR: SYNCENA Position */ +#define ITM_TCR_SYNCENA_Msk (1UL << ITM_TCR_SYNCENA_Pos) /*!< ITM TCR: SYNCENA Mask */ + +#define ITM_TCR_TSENA_Pos 1U /*!< ITM TCR: TSENA Position */ +#define ITM_TCR_TSENA_Msk (1UL << ITM_TCR_TSENA_Pos) /*!< ITM TCR: TSENA Mask */ + +#define ITM_TCR_ITMENA_Pos 0U /*!< ITM TCR: ITM Enable bit Position */ +#define ITM_TCR_ITMENA_Msk (1UL /*<< ITM_TCR_ITMENA_Pos*/) /*!< ITM TCR: ITM Enable bit Mask */ + +/* ITM Integration Write Register Definitions */ +#define ITM_IWR_ATVALIDM_Pos 0U /*!< ITM IWR: ATVALIDM Position */ +#define ITM_IWR_ATVALIDM_Msk (1UL /*<< ITM_IWR_ATVALIDM_Pos*/) /*!< ITM IWR: ATVALIDM Mask */ + +/* ITM Integration Read Register Definitions */ +#define ITM_IRR_ATREADYM_Pos 0U /*!< ITM IRR: ATREADYM Position */ +#define ITM_IRR_ATREADYM_Msk (1UL /*<< ITM_IRR_ATREADYM_Pos*/) /*!< ITM IRR: ATREADYM Mask */ + +/* ITM Integration Mode Control Register Definitions */ +#define ITM_IMCR_INTEGRATION_Pos 0U /*!< ITM IMCR: INTEGRATION Position */ +#define ITM_IMCR_INTEGRATION_Msk (1UL /*<< ITM_IMCR_INTEGRATION_Pos*/) /*!< ITM IMCR: INTEGRATION Mask */ + +/* ITM Lock Status Register Definitions */ +#define ITM_LSR_ByteAcc_Pos 2U /*!< ITM LSR: ByteAcc Position */ +#define ITM_LSR_ByteAcc_Msk (1UL << ITM_LSR_ByteAcc_Pos) /*!< ITM LSR: ByteAcc Mask */ + +#define ITM_LSR_Access_Pos 1U /*!< ITM LSR: Access Position */ +#define ITM_LSR_Access_Msk (1UL << ITM_LSR_Access_Pos) /*!< ITM LSR: Access Mask */ + +#define ITM_LSR_Present_Pos 0U /*!< ITM LSR: Present Position */ +#define ITM_LSR_Present_Msk (1UL /*<< ITM_LSR_Present_Pos*/) /*!< ITM LSR: Present Mask */ + +/*@}*/ /* end of group CMSIS_ITM */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_DWT Data Watchpoint and Trace (DWT) + \brief Type definitions for the Data Watchpoint and Trace (DWT) + @{ + */ + +/** + \brief Structure type to access the Data Watchpoint and Trace Register (DWT). + */ +typedef struct +{ + __IOM uint32_t CTRL; /*!< Offset: 0x000 (R/W) Control Register */ + __IOM uint32_t CYCCNT; /*!< Offset: 0x004 (R/W) Cycle Count Register */ + __IOM uint32_t CPICNT; /*!< Offset: 0x008 (R/W) CPI Count Register */ + __IOM uint32_t EXCCNT; /*!< Offset: 0x00C (R/W) Exception Overhead Count Register */ + __IOM uint32_t SLEEPCNT; /*!< Offset: 0x010 (R/W) Sleep Count Register */ + __IOM uint32_t LSUCNT; /*!< Offset: 0x014 (R/W) LSU Count Register */ + __IOM uint32_t FOLDCNT; /*!< Offset: 0x018 (R/W) Folded-instruction Count Register */ + __IM uint32_t PCSR; /*!< Offset: 0x01C (R/ ) Program Counter Sample Register */ + __IOM uint32_t COMP0; /*!< Offset: 0x020 (R/W) Comparator Register 0 */ + uint32_t RESERVED1[1U]; + __IOM uint32_t FUNCTION0; /*!< Offset: 0x028 (R/W) Function Register 0 */ + uint32_t RESERVED2[1U]; + __IOM uint32_t COMP1; /*!< Offset: 0x030 (R/W) Comparator Register 1 */ + uint32_t RESERVED3[1U]; + __IOM uint32_t FUNCTION1; /*!< Offset: 0x038 (R/W) Function Register 1 */ + uint32_t RESERVED4[1U]; + __IOM uint32_t COMP2; /*!< Offset: 0x040 (R/W) Comparator Register 2 */ + uint32_t RESERVED5[1U]; + __IOM uint32_t FUNCTION2; /*!< Offset: 0x048 (R/W) Function Register 2 */ + uint32_t RESERVED6[1U]; + __IOM uint32_t COMP3; /*!< Offset: 0x050 (R/W) Comparator Register 3 */ + uint32_t RESERVED7[1U]; + __IOM uint32_t FUNCTION3; /*!< Offset: 0x058 (R/W) Function Register 3 */ + uint32_t RESERVED8[1U]; + __IOM uint32_t COMP4; /*!< Offset: 0x060 (R/W) Comparator Register 4 */ + uint32_t RESERVED9[1U]; + __IOM uint32_t FUNCTION4; /*!< Offset: 0x068 (R/W) Function Register 4 */ + uint32_t RESERVED10[1U]; + __IOM uint32_t COMP5; /*!< Offset: 0x070 (R/W) Comparator Register 5 */ + uint32_t RESERVED11[1U]; + __IOM uint32_t FUNCTION5; /*!< Offset: 0x078 (R/W) Function Register 5 */ + uint32_t RESERVED12[1U]; + __IOM uint32_t COMP6; /*!< Offset: 0x080 (R/W) Comparator Register 6 */ + uint32_t RESERVED13[1U]; + __IOM uint32_t FUNCTION6; /*!< Offset: 0x088 (R/W) Function Register 6 */ + uint32_t RESERVED14[1U]; + __IOM uint32_t COMP7; /*!< Offset: 0x090 (R/W) Comparator Register 7 */ + uint32_t RESERVED15[1U]; + __IOM uint32_t FUNCTION7; /*!< Offset: 0x098 (R/W) Function Register 7 */ + uint32_t RESERVED16[1U]; + __IOM uint32_t COMP8; /*!< Offset: 0x0A0 (R/W) Comparator Register 8 */ + uint32_t RESERVED17[1U]; + __IOM uint32_t FUNCTION8; /*!< Offset: 0x0A8 (R/W) Function Register 8 */ + uint32_t RESERVED18[1U]; + __IOM uint32_t COMP9; /*!< Offset: 0x0B0 (R/W) Comparator Register 9 */ + uint32_t RESERVED19[1U]; + __IOM uint32_t FUNCTION9; /*!< Offset: 0x0B8 (R/W) Function Register 9 */ + uint32_t RESERVED20[1U]; + __IOM uint32_t COMP10; /*!< Offset: 0x0C0 (R/W) Comparator Register 10 */ + uint32_t RESERVED21[1U]; + __IOM uint32_t FUNCTION10; /*!< Offset: 0x0C8 (R/W) Function Register 10 */ + uint32_t RESERVED22[1U]; + __IOM uint32_t COMP11; /*!< Offset: 0x0D0 (R/W) Comparator Register 11 */ + uint32_t RESERVED23[1U]; + __IOM uint32_t FUNCTION11; /*!< Offset: 0x0D8 (R/W) Function Register 11 */ + uint32_t RESERVED24[1U]; + __IOM uint32_t COMP12; /*!< Offset: 0x0E0 (R/W) Comparator Register 12 */ + uint32_t RESERVED25[1U]; + __IOM uint32_t FUNCTION12; /*!< Offset: 0x0E8 (R/W) Function Register 12 */ + uint32_t RESERVED26[1U]; + __IOM uint32_t COMP13; /*!< Offset: 0x0F0 (R/W) Comparator Register 13 */ + uint32_t RESERVED27[1U]; + __IOM uint32_t FUNCTION13; /*!< Offset: 0x0F8 (R/W) Function Register 13 */ + uint32_t RESERVED28[1U]; + __IOM uint32_t COMP14; /*!< Offset: 0x100 (R/W) Comparator Register 14 */ + uint32_t RESERVED29[1U]; + __IOM uint32_t FUNCTION14; /*!< Offset: 0x108 (R/W) Function Register 14 */ + uint32_t RESERVED30[1U]; + __IOM uint32_t COMP15; /*!< Offset: 0x110 (R/W) Comparator Register 15 */ + uint32_t RESERVED31[1U]; + __IOM uint32_t FUNCTION15; /*!< Offset: 0x118 (R/W) Function Register 15 */ + uint32_t RESERVED32[934U]; + __IM uint32_t LSR; /*!< Offset: 0xFB4 (R ) Lock Status Register */ + uint32_t RESERVED33[1U]; + __IM uint32_t DEVARCH; /*!< Offset: 0xFBC (R/ ) Device Architecture Register */ +} DWT_Type; + +/* DWT Control Register Definitions */ +#define DWT_CTRL_NUMCOMP_Pos 28U /*!< DWT CTRL: NUMCOMP Position */ +#define DWT_CTRL_NUMCOMP_Msk (0xFUL << DWT_CTRL_NUMCOMP_Pos) /*!< DWT CTRL: NUMCOMP Mask */ + +#define DWT_CTRL_NOTRCPKT_Pos 27U /*!< DWT CTRL: NOTRCPKT Position */ +#define DWT_CTRL_NOTRCPKT_Msk (0x1UL << DWT_CTRL_NOTRCPKT_Pos) /*!< DWT CTRL: NOTRCPKT Mask */ + +#define DWT_CTRL_NOEXTTRIG_Pos 26U /*!< DWT CTRL: NOEXTTRIG Position */ +#define DWT_CTRL_NOEXTTRIG_Msk (0x1UL << DWT_CTRL_NOEXTTRIG_Pos) /*!< DWT CTRL: NOEXTTRIG Mask */ + +#define DWT_CTRL_NOCYCCNT_Pos 25U /*!< DWT CTRL: NOCYCCNT Position */ +#define DWT_CTRL_NOCYCCNT_Msk (0x1UL << DWT_CTRL_NOCYCCNT_Pos) /*!< DWT CTRL: NOCYCCNT Mask */ + +#define DWT_CTRL_NOPRFCNT_Pos 24U /*!< DWT CTRL: NOPRFCNT Position */ +#define DWT_CTRL_NOPRFCNT_Msk (0x1UL << DWT_CTRL_NOPRFCNT_Pos) /*!< DWT CTRL: NOPRFCNT Mask */ + +#define DWT_CTRL_CYCDISS_Pos 23U /*!< DWT CTRL: CYCDISS Position */ +#define DWT_CTRL_CYCDISS_Msk (0x1UL << DWT_CTRL_CYCDISS_Pos) /*!< DWT CTRL: CYCDISS Mask */ + +#define DWT_CTRL_CYCEVTENA_Pos 22U /*!< DWT CTRL: CYCEVTENA Position */ +#define DWT_CTRL_CYCEVTENA_Msk (0x1UL << DWT_CTRL_CYCEVTENA_Pos) /*!< DWT CTRL: CYCEVTENA Mask */ + +#define DWT_CTRL_FOLDEVTENA_Pos 21U /*!< DWT CTRL: FOLDEVTENA Position */ +#define DWT_CTRL_FOLDEVTENA_Msk (0x1UL << DWT_CTRL_FOLDEVTENA_Pos) /*!< DWT CTRL: FOLDEVTENA Mask */ + +#define DWT_CTRL_LSUEVTENA_Pos 20U /*!< DWT CTRL: LSUEVTENA Position */ +#define DWT_CTRL_LSUEVTENA_Msk (0x1UL << DWT_CTRL_LSUEVTENA_Pos) /*!< DWT CTRL: LSUEVTENA Mask */ + +#define DWT_CTRL_SLEEPEVTENA_Pos 19U /*!< DWT CTRL: SLEEPEVTENA Position */ +#define DWT_CTRL_SLEEPEVTENA_Msk (0x1UL << DWT_CTRL_SLEEPEVTENA_Pos) /*!< DWT CTRL: SLEEPEVTENA Mask */ + +#define DWT_CTRL_EXCEVTENA_Pos 18U /*!< DWT CTRL: EXCEVTENA Position */ +#define DWT_CTRL_EXCEVTENA_Msk (0x1UL << DWT_CTRL_EXCEVTENA_Pos) /*!< DWT CTRL: EXCEVTENA Mask */ + +#define DWT_CTRL_CPIEVTENA_Pos 17U /*!< DWT CTRL: CPIEVTENA Position */ +#define DWT_CTRL_CPIEVTENA_Msk (0x1UL << DWT_CTRL_CPIEVTENA_Pos) /*!< DWT CTRL: CPIEVTENA Mask */ + +#define DWT_CTRL_EXCTRCENA_Pos 16U /*!< DWT CTRL: EXCTRCENA Position */ +#define DWT_CTRL_EXCTRCENA_Msk (0x1UL << DWT_CTRL_EXCTRCENA_Pos) /*!< DWT CTRL: EXCTRCENA Mask */ + +#define DWT_CTRL_PCSAMPLENA_Pos 12U /*!< DWT CTRL: PCSAMPLENA Position */ +#define DWT_CTRL_PCSAMPLENA_Msk (0x1UL << DWT_CTRL_PCSAMPLENA_Pos) /*!< DWT CTRL: PCSAMPLENA Mask */ + +#define DWT_CTRL_SYNCTAP_Pos 10U /*!< DWT CTRL: SYNCTAP Position */ +#define DWT_CTRL_SYNCTAP_Msk (0x3UL << DWT_CTRL_SYNCTAP_Pos) /*!< DWT CTRL: SYNCTAP Mask */ + +#define DWT_CTRL_CYCTAP_Pos 9U /*!< DWT CTRL: CYCTAP Position */ +#define DWT_CTRL_CYCTAP_Msk (0x1UL << DWT_CTRL_CYCTAP_Pos) /*!< DWT CTRL: CYCTAP Mask */ + +#define DWT_CTRL_POSTINIT_Pos 5U /*!< DWT CTRL: POSTINIT Position */ +#define DWT_CTRL_POSTINIT_Msk (0xFUL << DWT_CTRL_POSTINIT_Pos) /*!< DWT CTRL: POSTINIT Mask */ + +#define DWT_CTRL_POSTPRESET_Pos 1U /*!< DWT CTRL: POSTPRESET Position */ +#define DWT_CTRL_POSTPRESET_Msk (0xFUL << DWT_CTRL_POSTPRESET_Pos) /*!< DWT CTRL: POSTPRESET Mask */ + +#define DWT_CTRL_CYCCNTENA_Pos 0U /*!< DWT CTRL: CYCCNTENA Position */ +#define DWT_CTRL_CYCCNTENA_Msk (0x1UL /*<< DWT_CTRL_CYCCNTENA_Pos*/) /*!< DWT CTRL: CYCCNTENA Mask */ + +/* DWT CPI Count Register Definitions */ +#define DWT_CPICNT_CPICNT_Pos 0U /*!< DWT CPICNT: CPICNT Position */ +#define DWT_CPICNT_CPICNT_Msk (0xFFUL /*<< DWT_CPICNT_CPICNT_Pos*/) /*!< DWT CPICNT: CPICNT Mask */ + +/* DWT Exception Overhead Count Register Definitions */ +#define DWT_EXCCNT_EXCCNT_Pos 0U /*!< DWT EXCCNT: EXCCNT Position */ +#define DWT_EXCCNT_EXCCNT_Msk (0xFFUL /*<< DWT_EXCCNT_EXCCNT_Pos*/) /*!< DWT EXCCNT: EXCCNT Mask */ + +/* DWT Sleep Count Register Definitions */ +#define DWT_SLEEPCNT_SLEEPCNT_Pos 0U /*!< DWT SLEEPCNT: SLEEPCNT Position */ +#define DWT_SLEEPCNT_SLEEPCNT_Msk (0xFFUL /*<< DWT_SLEEPCNT_SLEEPCNT_Pos*/) /*!< DWT SLEEPCNT: SLEEPCNT Mask */ + +/* DWT LSU Count Register Definitions */ +#define DWT_LSUCNT_LSUCNT_Pos 0U /*!< DWT LSUCNT: LSUCNT Position */ +#define DWT_LSUCNT_LSUCNT_Msk (0xFFUL /*<< DWT_LSUCNT_LSUCNT_Pos*/) /*!< DWT LSUCNT: LSUCNT Mask */ + +/* DWT Folded-instruction Count Register Definitions */ +#define DWT_FOLDCNT_FOLDCNT_Pos 0U /*!< DWT FOLDCNT: FOLDCNT Position */ +#define DWT_FOLDCNT_FOLDCNT_Msk (0xFFUL /*<< DWT_FOLDCNT_FOLDCNT_Pos*/) /*!< DWT FOLDCNT: FOLDCNT Mask */ + +/* DWT Comparator Function Register Definitions */ +#define DWT_FUNCTION_ID_Pos 27U /*!< DWT FUNCTION: ID Position */ +#define DWT_FUNCTION_ID_Msk (0x1FUL << DWT_FUNCTION_ID_Pos) /*!< DWT FUNCTION: ID Mask */ + +#define DWT_FUNCTION_MATCHED_Pos 24U /*!< DWT FUNCTION: MATCHED Position */ +#define DWT_FUNCTION_MATCHED_Msk (0x1UL << DWT_FUNCTION_MATCHED_Pos) /*!< DWT FUNCTION: MATCHED Mask */ + +#define DWT_FUNCTION_DATAVSIZE_Pos 10U /*!< DWT FUNCTION: DATAVSIZE Position */ +#define DWT_FUNCTION_DATAVSIZE_Msk (0x3UL << DWT_FUNCTION_DATAVSIZE_Pos) /*!< DWT FUNCTION: DATAVSIZE Mask */ + +#define DWT_FUNCTION_ACTION_Pos 4U /*!< DWT FUNCTION: ACTION Position */ +#define DWT_FUNCTION_ACTION_Msk (0x1UL << DWT_FUNCTION_ACTION_Pos) /*!< DWT FUNCTION: ACTION Mask */ + +#define DWT_FUNCTION_MATCH_Pos 0U /*!< DWT FUNCTION: MATCH Position */ +#define DWT_FUNCTION_MATCH_Msk (0xFUL /*<< DWT_FUNCTION_MATCH_Pos*/) /*!< DWT FUNCTION: MATCH Mask */ + +/*@}*/ /* end of group CMSIS_DWT */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_TPI Trace Port Interface (TPI) + \brief Type definitions for the Trace Port Interface (TPI) + @{ + */ + +/** + \brief Structure type to access the Trace Port Interface Register (TPI). + */ +typedef struct +{ + __IM uint32_t SSPSR; /*!< Offset: 0x000 (R/ ) Supported Parallel Port Sizes Register */ + __IOM uint32_t CSPSR; /*!< Offset: 0x004 (R/W) Current Parallel Port Sizes Register */ + uint32_t RESERVED0[2U]; + __IOM uint32_t ACPR; /*!< Offset: 0x010 (R/W) Asynchronous Clock Prescaler Register */ + uint32_t RESERVED1[55U]; + __IOM uint32_t SPPR; /*!< Offset: 0x0F0 (R/W) Selected Pin Protocol Register */ + uint32_t RESERVED2[131U]; + __IM uint32_t FFSR; /*!< Offset: 0x300 (R/ ) Formatter and Flush Status Register */ + __IOM uint32_t FFCR; /*!< Offset: 0x304 (R/W) Formatter and Flush Control Register */ + __IOM uint32_t PSCR; /*!< Offset: 0x308 (R/W) Periodic Synchronization Control Register */ + uint32_t RESERVED3[809U]; + __OM uint32_t LAR; /*!< Offset: 0xFB0 ( /W) Software Lock Access Register */ + __IM uint32_t LSR; /*!< Offset: 0xFB4 (R/ ) Software Lock Status Register */ + uint32_t RESERVED4[4U]; + __IM uint32_t TYPE; /*!< Offset: 0xFC8 (R/ ) Device Identifier Register */ + __IM uint32_t DEVTYPE; /*!< Offset: 0xFCC (R/ ) Device Type Register */ +} TPI_Type; + +/* TPI Asynchronous Clock Prescaler Register Definitions */ +#define TPI_ACPR_SWOSCALER_Pos 0U /*!< TPI ACPR: SWOSCALER Position */ +#define TPI_ACPR_SWOSCALER_Msk (0xFFFFUL /*<< TPI_ACPR_SWOSCALER_Pos*/) /*!< TPI ACPR: SWOSCALER Mask */ + +/* TPI Selected Pin Protocol Register Definitions */ +#define TPI_SPPR_TXMODE_Pos 0U /*!< TPI SPPR: TXMODE Position */ +#define TPI_SPPR_TXMODE_Msk (0x3UL /*<< TPI_SPPR_TXMODE_Pos*/) /*!< TPI SPPR: TXMODE Mask */ + +/* TPI Formatter and Flush Status Register Definitions */ +#define TPI_FFSR_FtNonStop_Pos 3U /*!< TPI FFSR: FtNonStop Position */ +#define TPI_FFSR_FtNonStop_Msk (0x1UL << TPI_FFSR_FtNonStop_Pos) /*!< TPI FFSR: FtNonStop Mask */ + +#define TPI_FFSR_TCPresent_Pos 2U /*!< TPI FFSR: TCPresent Position */ +#define TPI_FFSR_TCPresent_Msk (0x1UL << TPI_FFSR_TCPresent_Pos) /*!< TPI FFSR: TCPresent Mask */ + +#define TPI_FFSR_FtStopped_Pos 1U /*!< TPI FFSR: FtStopped Position */ +#define TPI_FFSR_FtStopped_Msk (0x1UL << TPI_FFSR_FtStopped_Pos) /*!< TPI FFSR: FtStopped Mask */ + +#define TPI_FFSR_FlInProg_Pos 0U /*!< TPI FFSR: FlInProg Position */ +#define TPI_FFSR_FlInProg_Msk (0x1UL /*<< TPI_FFSR_FlInProg_Pos*/) /*!< TPI FFSR: FlInProg Mask */ + +/* TPI Formatter and Flush Control Register Definitions */ +#define TPI_FFCR_TrigIn_Pos 8U /*!< TPI FFCR: TrigIn Position */ +#define TPI_FFCR_TrigIn_Msk (0x1UL << TPI_FFCR_TrigIn_Pos) /*!< TPI FFCR: TrigIn Mask */ + +#define TPI_FFCR_FOnMan_Pos 6U /*!< TPI FFCR: FOnMan Position */ +#define TPI_FFCR_FOnMan_Msk (0x1UL << TPI_FFCR_FOnMan_Pos) /*!< TPI FFCR: FOnMan Mask */ + +#define TPI_FFCR_EnFCont_Pos 1U /*!< TPI FFCR: EnFCont Position */ +#define TPI_FFCR_EnFCont_Msk (0x1UL << TPI_FFCR_EnFCont_Pos) /*!< TPI FFCR: EnFCont Mask */ + +/* TPI Periodic Synchronization Control Register Definitions */ +#define TPI_PSCR_PSCount_Pos 0U /*!< TPI PSCR: PSCount Position */ +#define TPI_PSCR_PSCount_Msk (0x1FUL /*<< TPI_PSCR_PSCount_Pos*/) /*!< TPI PSCR: TPSCount Mask */ + +/* TPI Software Lock Status Register Definitions */ +#define TPI_LSR_nTT_Pos 1U /*!< TPI LSR: Not thirty-two bit. Position */ +#define TPI_LSR_nTT_Msk (0x1UL << TPI_LSR_nTT_Pos) /*!< TPI LSR: Not thirty-two bit. Mask */ + +#define TPI_LSR_SLK_Pos 1U /*!< TPI LSR: Software Lock status Position */ +#define TPI_LSR_SLK_Msk (0x1UL << TPI_LSR_SLK_Pos) /*!< TPI LSR: Software Lock status Mask */ + +#define TPI_LSR_SLI_Pos 0U /*!< TPI LSR: Software Lock implemented Position */ +#define TPI_LSR_SLI_Msk (0x1UL /*<< TPI_LSR_SLI_Pos*/) /*!< TPI LSR: Software Lock implemented Mask */ + +/* TPI DEVID Register Definitions */ +#define TPI_DEVID_NRZVALID_Pos 11U /*!< TPI DEVID: NRZVALID Position */ +#define TPI_DEVID_NRZVALID_Msk (0x1UL << TPI_DEVID_NRZVALID_Pos) /*!< TPI DEVID: NRZVALID Mask */ + +#define TPI_DEVID_MANCVALID_Pos 10U /*!< TPI DEVID: MANCVALID Position */ +#define TPI_DEVID_MANCVALID_Msk (0x1UL << TPI_DEVID_MANCVALID_Pos) /*!< TPI DEVID: MANCVALID Mask */ + +#define TPI_DEVID_PTINVALID_Pos 9U /*!< TPI DEVID: PTINVALID Position */ +#define TPI_DEVID_PTINVALID_Msk (0x1UL << TPI_DEVID_PTINVALID_Pos) /*!< TPI DEVID: PTINVALID Mask */ + +#define TPI_DEVID_FIFOSZ_Pos 6U /*!< TPI DEVID: FIFO depth Position */ +#define TPI_DEVID_FIFOSZ_Msk (0x7UL << TPI_DEVID_FIFOSZ_Pos) /*!< TPI DEVID: FIFO depth Mask */ + +/* TPI DEVTYPE Register Definitions */ +#define TPI_DEVTYPE_SubType_Pos 4U /*!< TPI DEVTYPE: SubType Position */ +#define TPI_DEVTYPE_SubType_Msk (0xFUL /*<< TPI_DEVTYPE_SubType_Pos*/) /*!< TPI DEVTYPE: SubType Mask */ + +#define TPI_DEVTYPE_MajorType_Pos 0U /*!< TPI DEVTYPE: MajorType Position */ +#define TPI_DEVTYPE_MajorType_Msk (0xFUL << TPI_DEVTYPE_MajorType_Pos) /*!< TPI DEVTYPE: MajorType Mask */ + +/*@}*/ /* end of group CMSIS_TPI */ + + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_MPU Memory Protection Unit (MPU) + \brief Type definitions for the Memory Protection Unit (MPU) + @{ + */ + +/** + \brief Structure type to access the Memory Protection Unit (MPU). + */ +typedef struct +{ + __IM uint32_t TYPE; /*!< Offset: 0x000 (R/ ) MPU Type Register */ + __IOM uint32_t CTRL; /*!< Offset: 0x004 (R/W) MPU Control Register */ + __IOM uint32_t RNR; /*!< Offset: 0x008 (R/W) MPU Region Number Register */ + __IOM uint32_t RBAR; /*!< Offset: 0x00C (R/W) MPU Region Base Address Register */ + __IOM uint32_t RLAR; /*!< Offset: 0x010 (R/W) MPU Region Limit Address Register */ + __IOM uint32_t RBAR_A1; /*!< Offset: 0x014 (R/W) MPU Region Base Address Register Alias 1 */ + __IOM uint32_t RLAR_A1; /*!< Offset: 0x018 (R/W) MPU Region Limit Address Register Alias 1 */ + __IOM uint32_t RBAR_A2; /*!< Offset: 0x01C (R/W) MPU Region Base Address Register Alias 2 */ + __IOM uint32_t RLAR_A2; /*!< Offset: 0x020 (R/W) MPU Region Limit Address Register Alias 2 */ + __IOM uint32_t RBAR_A3; /*!< Offset: 0x024 (R/W) MPU Region Base Address Register Alias 3 */ + __IOM uint32_t RLAR_A3; /*!< Offset: 0x028 (R/W) MPU Region Limit Address Register Alias 3 */ + uint32_t RESERVED0[1]; + union + { + __IOM uint32_t MAIR[2]; + struct + { + __IOM uint32_t MAIR0; /*!< Offset: 0x030 (R/W) MPU Memory Attribute Indirection Register 0 */ + __IOM uint32_t MAIR1; /*!< Offset: 0x034 (R/W) MPU Memory Attribute Indirection Register 1 */ + }; + }; +} MPU_Type; + +#define MPU_TYPE_RALIASES 4U + +/* MPU Type Register Definitions */ +#define MPU_TYPE_IREGION_Pos 16U /*!< MPU TYPE: IREGION Position */ +#define MPU_TYPE_IREGION_Msk (0xFFUL << MPU_TYPE_IREGION_Pos) /*!< MPU TYPE: IREGION Mask */ + +#define MPU_TYPE_DREGION_Pos 8U /*!< MPU TYPE: DREGION Position */ +#define MPU_TYPE_DREGION_Msk (0xFFUL << MPU_TYPE_DREGION_Pos) /*!< MPU TYPE: DREGION Mask */ + +#define MPU_TYPE_SEPARATE_Pos 0U /*!< MPU TYPE: SEPARATE Position */ +#define MPU_TYPE_SEPARATE_Msk (1UL /*<< MPU_TYPE_SEPARATE_Pos*/) /*!< MPU TYPE: SEPARATE Mask */ + +/* MPU Control Register Definitions */ +#define MPU_CTRL_PRIVDEFENA_Pos 2U /*!< MPU CTRL: PRIVDEFENA Position */ +#define MPU_CTRL_PRIVDEFENA_Msk (1UL << MPU_CTRL_PRIVDEFENA_Pos) /*!< MPU CTRL: PRIVDEFENA Mask */ + +#define MPU_CTRL_HFNMIENA_Pos 1U /*!< MPU CTRL: HFNMIENA Position */ +#define MPU_CTRL_HFNMIENA_Msk (1UL << MPU_CTRL_HFNMIENA_Pos) /*!< MPU CTRL: HFNMIENA Mask */ + +#define MPU_CTRL_ENABLE_Pos 0U /*!< MPU CTRL: ENABLE Position */ +#define MPU_CTRL_ENABLE_Msk (1UL /*<< MPU_CTRL_ENABLE_Pos*/) /*!< MPU CTRL: ENABLE Mask */ + +/* MPU Region Number Register Definitions */ +#define MPU_RNR_REGION_Pos 0U /*!< MPU RNR: REGION Position */ +#define MPU_RNR_REGION_Msk (0xFFUL /*<< MPU_RNR_REGION_Pos*/) /*!< MPU RNR: REGION Mask */ + +/* MPU Region Base Address Register Definitions */ +#define MPU_RBAR_BASE_Pos 5U /*!< MPU RBAR: BASE Position */ +#define MPU_RBAR_BASE_Msk (0x7FFFFFFUL << MPU_RBAR_BASE_Pos) /*!< MPU RBAR: BASE Mask */ + +#define MPU_RBAR_SH_Pos 3U /*!< MPU RBAR: SH Position */ +#define MPU_RBAR_SH_Msk (0x3UL << MPU_RBAR_SH_Pos) /*!< MPU RBAR: SH Mask */ + +#define MPU_RBAR_AP_Pos 1U /*!< MPU RBAR: AP Position */ +#define MPU_RBAR_AP_Msk (0x3UL << MPU_RBAR_AP_Pos) /*!< MPU RBAR: AP Mask */ + +#define MPU_RBAR_XN_Pos 0U /*!< MPU RBAR: XN Position */ +#define MPU_RBAR_XN_Msk (01UL /*<< MPU_RBAR_XN_Pos*/) /*!< MPU RBAR: XN Mask */ + +/* MPU Region Limit Address Register Definitions */ +#define MPU_RLAR_LIMIT_Pos 5U /*!< MPU RLAR: LIMIT Position */ +#define MPU_RLAR_LIMIT_Msk (0x7FFFFFFUL << MPU_RLAR_LIMIT_Pos) /*!< MPU RLAR: LIMIT Mask */ + +#define MPU_RLAR_AttrIndx_Pos 1U /*!< MPU RLAR: AttrIndx Position */ +#define MPU_RLAR_AttrIndx_Msk (0x7UL << MPU_RLAR_AttrIndx_Pos) /*!< MPU RLAR: AttrIndx Mask */ + +#define MPU_RLAR_EN_Pos 0U /*!< MPU RLAR: Region enable bit Position */ +#define MPU_RLAR_EN_Msk (1UL /*<< MPU_RLAR_EN_Pos*/) /*!< MPU RLAR: Region enable bit Disable Mask */ + +/* MPU Memory Attribute Indirection Register 0 Definitions */ +#define MPU_MAIR0_Attr3_Pos 24U /*!< MPU MAIR0: Attr3 Position */ +#define MPU_MAIR0_Attr3_Msk (0xFFUL << MPU_MAIR0_Attr3_Pos) /*!< MPU MAIR0: Attr3 Mask */ + +#define MPU_MAIR0_Attr2_Pos 16U /*!< MPU MAIR0: Attr2 Position */ +#define MPU_MAIR0_Attr2_Msk (0xFFUL << MPU_MAIR0_Attr2_Pos) /*!< MPU MAIR0: Attr2 Mask */ + +#define MPU_MAIR0_Attr1_Pos 8U /*!< MPU MAIR0: Attr1 Position */ +#define MPU_MAIR0_Attr1_Msk (0xFFUL << MPU_MAIR0_Attr1_Pos) /*!< MPU MAIR0: Attr1 Mask */ + +#define MPU_MAIR0_Attr0_Pos 0U /*!< MPU MAIR0: Attr0 Position */ +#define MPU_MAIR0_Attr0_Msk (0xFFUL /*<< MPU_MAIR0_Attr0_Pos*/) /*!< MPU MAIR0: Attr0 Mask */ + +/* MPU Memory Attribute Indirection Register 1 Definitions */ +#define MPU_MAIR1_Attr7_Pos 24U /*!< MPU MAIR1: Attr7 Position */ +#define MPU_MAIR1_Attr7_Msk (0xFFUL << MPU_MAIR1_Attr7_Pos) /*!< MPU MAIR1: Attr7 Mask */ + +#define MPU_MAIR1_Attr6_Pos 16U /*!< MPU MAIR1: Attr6 Position */ +#define MPU_MAIR1_Attr6_Msk (0xFFUL << MPU_MAIR1_Attr6_Pos) /*!< MPU MAIR1: Attr6 Mask */ + +#define MPU_MAIR1_Attr5_Pos 8U /*!< MPU MAIR1: Attr5 Position */ +#define MPU_MAIR1_Attr5_Msk (0xFFUL << MPU_MAIR1_Attr5_Pos) /*!< MPU MAIR1: Attr5 Mask */ + +#define MPU_MAIR1_Attr4_Pos 0U /*!< MPU MAIR1: Attr4 Position */ +#define MPU_MAIR1_Attr4_Msk (0xFFUL /*<< MPU_MAIR1_Attr4_Pos*/) /*!< MPU MAIR1: Attr4 Mask */ + +/*@} end of group CMSIS_MPU */ +#endif + + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SAU Security Attribution Unit (SAU) + \brief Type definitions for the Security Attribution Unit (SAU) + @{ + */ + +/** + \brief Structure type to access the Security Attribution Unit (SAU). + */ +typedef struct +{ + __IOM uint32_t CTRL; /*!< Offset: 0x000 (R/W) SAU Control Register */ + __IM uint32_t TYPE; /*!< Offset: 0x004 (R/ ) SAU Type Register */ +#if defined (__SAUREGION_PRESENT) && (__SAUREGION_PRESENT == 1U) + __IOM uint32_t RNR; /*!< Offset: 0x008 (R/W) SAU Region Number Register */ + __IOM uint32_t RBAR; /*!< Offset: 0x00C (R/W) SAU Region Base Address Register */ + __IOM uint32_t RLAR; /*!< Offset: 0x010 (R/W) SAU Region Limit Address Register */ +#else + uint32_t RESERVED0[3]; +#endif + __IOM uint32_t SFSR; /*!< Offset: 0x014 (R/W) Secure Fault Status Register */ + __IOM uint32_t SFAR; /*!< Offset: 0x018 (R/W) Secure Fault Address Register */ +} SAU_Type; + +/* SAU Control Register Definitions */ +#define SAU_CTRL_ALLNS_Pos 1U /*!< SAU CTRL: ALLNS Position */ +#define SAU_CTRL_ALLNS_Msk (1UL << SAU_CTRL_ALLNS_Pos) /*!< SAU CTRL: ALLNS Mask */ + +#define SAU_CTRL_ENABLE_Pos 0U /*!< SAU CTRL: ENABLE Position */ +#define SAU_CTRL_ENABLE_Msk (1UL /*<< SAU_CTRL_ENABLE_Pos*/) /*!< SAU CTRL: ENABLE Mask */ + +/* SAU Type Register Definitions */ +#define SAU_TYPE_SREGION_Pos 0U /*!< SAU TYPE: SREGION Position */ +#define SAU_TYPE_SREGION_Msk (0xFFUL /*<< SAU_TYPE_SREGION_Pos*/) /*!< SAU TYPE: SREGION Mask */ + +#if defined (__SAUREGION_PRESENT) && (__SAUREGION_PRESENT == 1U) +/* SAU Region Number Register Definitions */ +#define SAU_RNR_REGION_Pos 0U /*!< SAU RNR: REGION Position */ +#define SAU_RNR_REGION_Msk (0xFFUL /*<< SAU_RNR_REGION_Pos*/) /*!< SAU RNR: REGION Mask */ + +/* SAU Region Base Address Register Definitions */ +#define SAU_RBAR_BADDR_Pos 5U /*!< SAU RBAR: BADDR Position */ +#define SAU_RBAR_BADDR_Msk (0x7FFFFFFUL << SAU_RBAR_BADDR_Pos) /*!< SAU RBAR: BADDR Mask */ + +/* SAU Region Limit Address Register Definitions */ +#define SAU_RLAR_LADDR_Pos 5U /*!< SAU RLAR: LADDR Position */ +#define SAU_RLAR_LADDR_Msk (0x7FFFFFFUL << SAU_RLAR_LADDR_Pos) /*!< SAU RLAR: LADDR Mask */ + +#define SAU_RLAR_NSC_Pos 1U /*!< SAU RLAR: NSC Position */ +#define SAU_RLAR_NSC_Msk (1UL << SAU_RLAR_NSC_Pos) /*!< SAU RLAR: NSC Mask */ + +#define SAU_RLAR_ENABLE_Pos 0U /*!< SAU RLAR: ENABLE Position */ +#define SAU_RLAR_ENABLE_Msk (1UL /*<< SAU_RLAR_ENABLE_Pos*/) /*!< SAU RLAR: ENABLE Mask */ + +#endif /* defined (__SAUREGION_PRESENT) && (__SAUREGION_PRESENT == 1U) */ + +/* Secure Fault Status Register Definitions */ +#define SAU_SFSR_LSERR_Pos 7U /*!< SAU SFSR: LSERR Position */ +#define SAU_SFSR_LSERR_Msk (1UL << SAU_SFSR_LSERR_Pos) /*!< SAU SFSR: LSERR Mask */ + +#define SAU_SFSR_SFARVALID_Pos 6U /*!< SAU SFSR: SFARVALID Position */ +#define SAU_SFSR_SFARVALID_Msk (1UL << SAU_SFSR_SFARVALID_Pos) /*!< SAU SFSR: SFARVALID Mask */ + +#define SAU_SFSR_LSPERR_Pos 5U /*!< SAU SFSR: LSPERR Position */ +#define SAU_SFSR_LSPERR_Msk (1UL << SAU_SFSR_LSPERR_Pos) /*!< SAU SFSR: LSPERR Mask */ + +#define SAU_SFSR_INVTRAN_Pos 4U /*!< SAU SFSR: INVTRAN Position */ +#define SAU_SFSR_INVTRAN_Msk (1UL << SAU_SFSR_INVTRAN_Pos) /*!< SAU SFSR: INVTRAN Mask */ + +#define SAU_SFSR_AUVIOL_Pos 3U /*!< SAU SFSR: AUVIOL Position */ +#define SAU_SFSR_AUVIOL_Msk (1UL << SAU_SFSR_AUVIOL_Pos) /*!< SAU SFSR: AUVIOL Mask */ + +#define SAU_SFSR_INVER_Pos 2U /*!< SAU SFSR: INVER Position */ +#define SAU_SFSR_INVER_Msk (1UL << SAU_SFSR_INVER_Pos) /*!< SAU SFSR: INVER Mask */ + +#define SAU_SFSR_INVIS_Pos 1U /*!< SAU SFSR: INVIS Position */ +#define SAU_SFSR_INVIS_Msk (1UL << SAU_SFSR_INVIS_Pos) /*!< SAU SFSR: INVIS Mask */ + +#define SAU_SFSR_INVEP_Pos 0U /*!< SAU SFSR: INVEP Position */ +#define SAU_SFSR_INVEP_Msk (1UL /*<< SAU_SFSR_INVEP_Pos*/) /*!< SAU SFSR: INVEP Mask */ + +/*@} end of group CMSIS_SAU */ +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_FPU Floating Point Unit (FPU) + \brief Type definitions for the Floating Point Unit (FPU) + @{ + */ + +/** + \brief Structure type to access the Floating Point Unit (FPU). + */ +typedef struct +{ + uint32_t RESERVED0[1U]; + __IOM uint32_t FPCCR; /*!< Offset: 0x004 (R/W) Floating-Point Context Control Register */ + __IOM uint32_t FPCAR; /*!< Offset: 0x008 (R/W) Floating-Point Context Address Register */ + __IOM uint32_t FPDSCR; /*!< Offset: 0x00C (R/W) Floating-Point Default Status Control Register */ + __IM uint32_t MVFR0; /*!< Offset: 0x010 (R/ ) Media and FP Feature Register 0 */ + __IM uint32_t MVFR1; /*!< Offset: 0x014 (R/ ) Media and FP Feature Register 1 */ +} FPU_Type; + +/* Floating-Point Context Control Register Definitions */ +#define FPU_FPCCR_ASPEN_Pos 31U /*!< FPCCR: ASPEN bit Position */ +#define FPU_FPCCR_ASPEN_Msk (1UL << FPU_FPCCR_ASPEN_Pos) /*!< FPCCR: ASPEN bit Mask */ + +#define FPU_FPCCR_LSPEN_Pos 30U /*!< FPCCR: LSPEN Position */ +#define FPU_FPCCR_LSPEN_Msk (1UL << FPU_FPCCR_LSPEN_Pos) /*!< FPCCR: LSPEN bit Mask */ + +#define FPU_FPCCR_LSPENS_Pos 29U /*!< FPCCR: LSPENS Position */ +#define FPU_FPCCR_LSPENS_Msk (1UL << FPU_FPCCR_LSPENS_Pos) /*!< FPCCR: LSPENS bit Mask */ + +#define FPU_FPCCR_CLRONRET_Pos 28U /*!< FPCCR: CLRONRET Position */ +#define FPU_FPCCR_CLRONRET_Msk (1UL << FPU_FPCCR_CLRONRET_Pos) /*!< FPCCR: CLRONRET bit Mask */ + +#define FPU_FPCCR_CLRONRETS_Pos 27U /*!< FPCCR: CLRONRETS Position */ +#define FPU_FPCCR_CLRONRETS_Msk (1UL << FPU_FPCCR_CLRONRETS_Pos) /*!< FPCCR: CLRONRETS bit Mask */ + +#define FPU_FPCCR_TS_Pos 26U /*!< FPCCR: TS Position */ +#define FPU_FPCCR_TS_Msk (1UL << FPU_FPCCR_TS_Pos) /*!< FPCCR: TS bit Mask */ + +#define FPU_FPCCR_UFRDY_Pos 10U /*!< FPCCR: UFRDY Position */ +#define FPU_FPCCR_UFRDY_Msk (1UL << FPU_FPCCR_UFRDY_Pos) /*!< FPCCR: UFRDY bit Mask */ + +#define FPU_FPCCR_SPLIMVIOL_Pos 9U /*!< FPCCR: SPLIMVIOL Position */ +#define FPU_FPCCR_SPLIMVIOL_Msk (1UL << FPU_FPCCR_SPLIMVIOL_Pos) /*!< FPCCR: SPLIMVIOL bit Mask */ + +#define FPU_FPCCR_MONRDY_Pos 8U /*!< FPCCR: MONRDY Position */ +#define FPU_FPCCR_MONRDY_Msk (1UL << FPU_FPCCR_MONRDY_Pos) /*!< FPCCR: MONRDY bit Mask */ + +#define FPU_FPCCR_SFRDY_Pos 7U /*!< FPCCR: SFRDY Position */ +#define FPU_FPCCR_SFRDY_Msk (1UL << FPU_FPCCR_SFRDY_Pos) /*!< FPCCR: SFRDY bit Mask */ + +#define FPU_FPCCR_BFRDY_Pos 6U /*!< FPCCR: BFRDY Position */ +#define FPU_FPCCR_BFRDY_Msk (1UL << FPU_FPCCR_BFRDY_Pos) /*!< FPCCR: BFRDY bit Mask */ + +#define FPU_FPCCR_MMRDY_Pos 5U /*!< FPCCR: MMRDY Position */ +#define FPU_FPCCR_MMRDY_Msk (1UL << FPU_FPCCR_MMRDY_Pos) /*!< FPCCR: MMRDY bit Mask */ + +#define FPU_FPCCR_HFRDY_Pos 4U /*!< FPCCR: HFRDY Position */ +#define FPU_FPCCR_HFRDY_Msk (1UL << FPU_FPCCR_HFRDY_Pos) /*!< FPCCR: HFRDY bit Mask */ + +#define FPU_FPCCR_THREAD_Pos 3U /*!< FPCCR: processor mode bit Position */ +#define FPU_FPCCR_THREAD_Msk (1UL << FPU_FPCCR_THREAD_Pos) /*!< FPCCR: processor mode active bit Mask */ + +#define FPU_FPCCR_S_Pos 2U /*!< FPCCR: Security status of the FP context bit Position */ +#define FPU_FPCCR_S_Msk (1UL << FPU_FPCCR_S_Pos) /*!< FPCCR: Security status of the FP context bit Mask */ + +#define FPU_FPCCR_USER_Pos 1U /*!< FPCCR: privilege level bit Position */ +#define FPU_FPCCR_USER_Msk (1UL << FPU_FPCCR_USER_Pos) /*!< FPCCR: privilege level bit Mask */ + +#define FPU_FPCCR_LSPACT_Pos 0U /*!< FPCCR: Lazy state preservation active bit Position */ +#define FPU_FPCCR_LSPACT_Msk (1UL /*<< FPU_FPCCR_LSPACT_Pos*/) /*!< FPCCR: Lazy state preservation active bit Mask */ + +/* Floating-Point Context Address Register Definitions */ +#define FPU_FPCAR_ADDRESS_Pos 3U /*!< FPCAR: ADDRESS bit Position */ +#define FPU_FPCAR_ADDRESS_Msk (0x1FFFFFFFUL << FPU_FPCAR_ADDRESS_Pos) /*!< FPCAR: ADDRESS bit Mask */ + +/* Floating-Point Default Status Control Register Definitions */ +#define FPU_FPDSCR_AHP_Pos 26U /*!< FPDSCR: AHP bit Position */ +#define FPU_FPDSCR_AHP_Msk (1UL << FPU_FPDSCR_AHP_Pos) /*!< FPDSCR: AHP bit Mask */ + +#define FPU_FPDSCR_DN_Pos 25U /*!< FPDSCR: DN bit Position */ +#define FPU_FPDSCR_DN_Msk (1UL << FPU_FPDSCR_DN_Pos) /*!< FPDSCR: DN bit Mask */ + +#define FPU_FPDSCR_FZ_Pos 24U /*!< FPDSCR: FZ bit Position */ +#define FPU_FPDSCR_FZ_Msk (1UL << FPU_FPDSCR_FZ_Pos) /*!< FPDSCR: FZ bit Mask */ + +#define FPU_FPDSCR_RMode_Pos 22U /*!< FPDSCR: RMode bit Position */ +#define FPU_FPDSCR_RMode_Msk (3UL << FPU_FPDSCR_RMode_Pos) /*!< FPDSCR: RMode bit Mask */ + +/* Media and FP Feature Register 0 Definitions */ +#define FPU_MVFR0_FP_rounding_modes_Pos 28U /*!< MVFR0: FP rounding modes bits Position */ +#define FPU_MVFR0_FP_rounding_modes_Msk (0xFUL << FPU_MVFR0_FP_rounding_modes_Pos) /*!< MVFR0: FP rounding modes bits Mask */ + +#define FPU_MVFR0_Short_vectors_Pos 24U /*!< MVFR0: Short vectors bits Position */ +#define FPU_MVFR0_Short_vectors_Msk (0xFUL << FPU_MVFR0_Short_vectors_Pos) /*!< MVFR0: Short vectors bits Mask */ + +#define FPU_MVFR0_Square_root_Pos 20U /*!< MVFR0: Square root bits Position */ +#define FPU_MVFR0_Square_root_Msk (0xFUL << FPU_MVFR0_Square_root_Pos) /*!< MVFR0: Square root bits Mask */ + +#define FPU_MVFR0_Divide_Pos 16U /*!< MVFR0: Divide bits Position */ +#define FPU_MVFR0_Divide_Msk (0xFUL << FPU_MVFR0_Divide_Pos) /*!< MVFR0: Divide bits Mask */ + +#define FPU_MVFR0_FP_excep_trapping_Pos 12U /*!< MVFR0: FP exception trapping bits Position */ +#define FPU_MVFR0_FP_excep_trapping_Msk (0xFUL << FPU_MVFR0_FP_excep_trapping_Pos) /*!< MVFR0: FP exception trapping bits Mask */ + +#define FPU_MVFR0_Double_precision_Pos 8U /*!< MVFR0: Double-precision bits Position */ +#define FPU_MVFR0_Double_precision_Msk (0xFUL << FPU_MVFR0_Double_precision_Pos) /*!< MVFR0: Double-precision bits Mask */ + +#define FPU_MVFR0_Single_precision_Pos 4U /*!< MVFR0: Single-precision bits Position */ +#define FPU_MVFR0_Single_precision_Msk (0xFUL << FPU_MVFR0_Single_precision_Pos) /*!< MVFR0: Single-precision bits Mask */ + +#define FPU_MVFR0_A_SIMD_registers_Pos 0U /*!< MVFR0: A_SIMD registers bits Position */ +#define FPU_MVFR0_A_SIMD_registers_Msk (0xFUL /*<< FPU_MVFR0_A_SIMD_registers_Pos*/) /*!< MVFR0: A_SIMD registers bits Mask */ + +/* Media and FP Feature Register 1 Definitions */ +#define FPU_MVFR1_FP_fused_MAC_Pos 28U /*!< MVFR1: FP fused MAC bits Position */ +#define FPU_MVFR1_FP_fused_MAC_Msk (0xFUL << FPU_MVFR1_FP_fused_MAC_Pos) /*!< MVFR1: FP fused MAC bits Mask */ + +#define FPU_MVFR1_FP_HPFP_Pos 24U /*!< MVFR1: FP HPFP bits Position */ +#define FPU_MVFR1_FP_HPFP_Msk (0xFUL << FPU_MVFR1_FP_HPFP_Pos) /*!< MVFR1: FP HPFP bits Mask */ + +#define FPU_MVFR1_D_NaN_mode_Pos 4U /*!< MVFR1: D_NaN mode bits Position */ +#define FPU_MVFR1_D_NaN_mode_Msk (0xFUL << FPU_MVFR1_D_NaN_mode_Pos) /*!< MVFR1: D_NaN mode bits Mask */ + +#define FPU_MVFR1_FtZ_mode_Pos 0U /*!< MVFR1: FtZ mode bits Position */ +#define FPU_MVFR1_FtZ_mode_Msk (0xFUL /*<< FPU_MVFR1_FtZ_mode_Pos*/) /*!< MVFR1: FtZ mode bits Mask */ + +/*@} end of group CMSIS_FPU */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_CoreDebug Core Debug Registers (CoreDebug) + \brief Type definitions for the Core Debug Registers + @{ + */ + +/** + \brief Structure type to access the Core Debug Register (CoreDebug). + */ +typedef struct +{ + __IOM uint32_t DHCSR; /*!< Offset: 0x000 (R/W) Debug Halting Control and Status Register */ + __OM uint32_t DCRSR; /*!< Offset: 0x004 ( /W) Debug Core Register Selector Register */ + __IOM uint32_t DCRDR; /*!< Offset: 0x008 (R/W) Debug Core Register Data Register */ + __IOM uint32_t DEMCR; /*!< Offset: 0x00C (R/W) Debug Exception and Monitor Control Register */ + uint32_t RESERVED4[1U]; + __IOM uint32_t DAUTHCTRL; /*!< Offset: 0x014 (R/W) Debug Authentication Control Register */ + __IOM uint32_t DSCSR; /*!< Offset: 0x018 (R/W) Debug Security Control and Status Register */ +} CoreDebug_Type; + +/* Debug Halting Control and Status Register Definitions */ +#define CoreDebug_DHCSR_DBGKEY_Pos 16U /*!< CoreDebug DHCSR: DBGKEY Position */ +#define CoreDebug_DHCSR_DBGKEY_Msk (0xFFFFUL << CoreDebug_DHCSR_DBGKEY_Pos) /*!< CoreDebug DHCSR: DBGKEY Mask */ + +#define CoreDebug_DHCSR_S_RESTART_ST_Pos 26U /*!< CoreDebug DHCSR: S_RESTART_ST Position */ +#define CoreDebug_DHCSR_S_RESTART_ST_Msk (1UL << CoreDebug_DHCSR_S_RESTART_ST_Pos) /*!< CoreDebug DHCSR: S_RESTART_ST Mask */ + +#define CoreDebug_DHCSR_S_RESET_ST_Pos 25U /*!< CoreDebug DHCSR: S_RESET_ST Position */ +#define CoreDebug_DHCSR_S_RESET_ST_Msk (1UL << CoreDebug_DHCSR_S_RESET_ST_Pos) /*!< CoreDebug DHCSR: S_RESET_ST Mask */ + +#define CoreDebug_DHCSR_S_RETIRE_ST_Pos 24U /*!< CoreDebug DHCSR: S_RETIRE_ST Position */ +#define CoreDebug_DHCSR_S_RETIRE_ST_Msk (1UL << CoreDebug_DHCSR_S_RETIRE_ST_Pos) /*!< CoreDebug DHCSR: S_RETIRE_ST Mask */ + +#define CoreDebug_DHCSR_S_LOCKUP_Pos 19U /*!< CoreDebug DHCSR: S_LOCKUP Position */ +#define CoreDebug_DHCSR_S_LOCKUP_Msk (1UL << CoreDebug_DHCSR_S_LOCKUP_Pos) /*!< CoreDebug DHCSR: S_LOCKUP Mask */ + +#define CoreDebug_DHCSR_S_SLEEP_Pos 18U /*!< CoreDebug DHCSR: S_SLEEP Position */ +#define CoreDebug_DHCSR_S_SLEEP_Msk (1UL << CoreDebug_DHCSR_S_SLEEP_Pos) /*!< CoreDebug DHCSR: S_SLEEP Mask */ + +#define CoreDebug_DHCSR_S_HALT_Pos 17U /*!< CoreDebug DHCSR: S_HALT Position */ +#define CoreDebug_DHCSR_S_HALT_Msk (1UL << CoreDebug_DHCSR_S_HALT_Pos) /*!< CoreDebug DHCSR: S_HALT Mask */ + +#define CoreDebug_DHCSR_S_REGRDY_Pos 16U /*!< CoreDebug DHCSR: S_REGRDY Position */ +#define CoreDebug_DHCSR_S_REGRDY_Msk (1UL << CoreDebug_DHCSR_S_REGRDY_Pos) /*!< CoreDebug DHCSR: S_REGRDY Mask */ + +#define CoreDebug_DHCSR_C_SNAPSTALL_Pos 5U /*!< CoreDebug DHCSR: C_SNAPSTALL Position */ +#define CoreDebug_DHCSR_C_SNAPSTALL_Msk (1UL << CoreDebug_DHCSR_C_SNAPSTALL_Pos) /*!< CoreDebug DHCSR: C_SNAPSTALL Mask */ + +#define CoreDebug_DHCSR_C_MASKINTS_Pos 3U /*!< CoreDebug DHCSR: C_MASKINTS Position */ +#define CoreDebug_DHCSR_C_MASKINTS_Msk (1UL << CoreDebug_DHCSR_C_MASKINTS_Pos) /*!< CoreDebug DHCSR: C_MASKINTS Mask */ + +#define CoreDebug_DHCSR_C_STEP_Pos 2U /*!< CoreDebug DHCSR: C_STEP Position */ +#define CoreDebug_DHCSR_C_STEP_Msk (1UL << CoreDebug_DHCSR_C_STEP_Pos) /*!< CoreDebug DHCSR: C_STEP Mask */ + +#define CoreDebug_DHCSR_C_HALT_Pos 1U /*!< CoreDebug DHCSR: C_HALT Position */ +#define CoreDebug_DHCSR_C_HALT_Msk (1UL << CoreDebug_DHCSR_C_HALT_Pos) /*!< CoreDebug DHCSR: C_HALT Mask */ + +#define CoreDebug_DHCSR_C_DEBUGEN_Pos 0U /*!< CoreDebug DHCSR: C_DEBUGEN Position */ +#define CoreDebug_DHCSR_C_DEBUGEN_Msk (1UL /*<< CoreDebug_DHCSR_C_DEBUGEN_Pos*/) /*!< CoreDebug DHCSR: C_DEBUGEN Mask */ + +/* Debug Core Register Selector Register Definitions */ +#define CoreDebug_DCRSR_REGWnR_Pos 16U /*!< CoreDebug DCRSR: REGWnR Position */ +#define CoreDebug_DCRSR_REGWnR_Msk (1UL << CoreDebug_DCRSR_REGWnR_Pos) /*!< CoreDebug DCRSR: REGWnR Mask */ + +#define CoreDebug_DCRSR_REGSEL_Pos 0U /*!< CoreDebug DCRSR: REGSEL Position */ +#define CoreDebug_DCRSR_REGSEL_Msk (0x1FUL /*<< CoreDebug_DCRSR_REGSEL_Pos*/) /*!< CoreDebug DCRSR: REGSEL Mask */ + +/* Debug Exception and Monitor Control Register Definitions */ +#define CoreDebug_DEMCR_TRCENA_Pos 24U /*!< CoreDebug DEMCR: TRCENA Position */ +#define CoreDebug_DEMCR_TRCENA_Msk (1UL << CoreDebug_DEMCR_TRCENA_Pos) /*!< CoreDebug DEMCR: TRCENA Mask */ + +#define CoreDebug_DEMCR_MON_REQ_Pos 19U /*!< CoreDebug DEMCR: MON_REQ Position */ +#define CoreDebug_DEMCR_MON_REQ_Msk (1UL << CoreDebug_DEMCR_MON_REQ_Pos) /*!< CoreDebug DEMCR: MON_REQ Mask */ + +#define CoreDebug_DEMCR_MON_STEP_Pos 18U /*!< CoreDebug DEMCR: MON_STEP Position */ +#define CoreDebug_DEMCR_MON_STEP_Msk (1UL << CoreDebug_DEMCR_MON_STEP_Pos) /*!< CoreDebug DEMCR: MON_STEP Mask */ + +#define CoreDebug_DEMCR_MON_PEND_Pos 17U /*!< CoreDebug DEMCR: MON_PEND Position */ +#define CoreDebug_DEMCR_MON_PEND_Msk (1UL << CoreDebug_DEMCR_MON_PEND_Pos) /*!< CoreDebug DEMCR: MON_PEND Mask */ + +#define CoreDebug_DEMCR_MON_EN_Pos 16U /*!< CoreDebug DEMCR: MON_EN Position */ +#define CoreDebug_DEMCR_MON_EN_Msk (1UL << CoreDebug_DEMCR_MON_EN_Pos) /*!< CoreDebug DEMCR: MON_EN Mask */ + +#define CoreDebug_DEMCR_VC_HARDERR_Pos 10U /*!< CoreDebug DEMCR: VC_HARDERR Position */ +#define CoreDebug_DEMCR_VC_HARDERR_Msk (1UL << CoreDebug_DEMCR_VC_HARDERR_Pos) /*!< CoreDebug DEMCR: VC_HARDERR Mask */ + +#define CoreDebug_DEMCR_VC_INTERR_Pos 9U /*!< CoreDebug DEMCR: VC_INTERR Position */ +#define CoreDebug_DEMCR_VC_INTERR_Msk (1UL << CoreDebug_DEMCR_VC_INTERR_Pos) /*!< CoreDebug DEMCR: VC_INTERR Mask */ + +#define CoreDebug_DEMCR_VC_BUSERR_Pos 8U /*!< CoreDebug DEMCR: VC_BUSERR Position */ +#define CoreDebug_DEMCR_VC_BUSERR_Msk (1UL << CoreDebug_DEMCR_VC_BUSERR_Pos) /*!< CoreDebug DEMCR: VC_BUSERR Mask */ + +#define CoreDebug_DEMCR_VC_STATERR_Pos 7U /*!< CoreDebug DEMCR: VC_STATERR Position */ +#define CoreDebug_DEMCR_VC_STATERR_Msk (1UL << CoreDebug_DEMCR_VC_STATERR_Pos) /*!< CoreDebug DEMCR: VC_STATERR Mask */ + +#define CoreDebug_DEMCR_VC_CHKERR_Pos 6U /*!< CoreDebug DEMCR: VC_CHKERR Position */ +#define CoreDebug_DEMCR_VC_CHKERR_Msk (1UL << CoreDebug_DEMCR_VC_CHKERR_Pos) /*!< CoreDebug DEMCR: VC_CHKERR Mask */ + +#define CoreDebug_DEMCR_VC_NOCPERR_Pos 5U /*!< CoreDebug DEMCR: VC_NOCPERR Position */ +#define CoreDebug_DEMCR_VC_NOCPERR_Msk (1UL << CoreDebug_DEMCR_VC_NOCPERR_Pos) /*!< CoreDebug DEMCR: VC_NOCPERR Mask */ + +#define CoreDebug_DEMCR_VC_MMERR_Pos 4U /*!< CoreDebug DEMCR: VC_MMERR Position */ +#define CoreDebug_DEMCR_VC_MMERR_Msk (1UL << CoreDebug_DEMCR_VC_MMERR_Pos) /*!< CoreDebug DEMCR: VC_MMERR Mask */ + +#define CoreDebug_DEMCR_VC_CORERESET_Pos 0U /*!< CoreDebug DEMCR: VC_CORERESET Position */ +#define CoreDebug_DEMCR_VC_CORERESET_Msk (1UL /*<< CoreDebug_DEMCR_VC_CORERESET_Pos*/) /*!< CoreDebug DEMCR: VC_CORERESET Mask */ + +/* Debug Authentication Control Register Definitions */ +#define CoreDebug_DAUTHCTRL_INTSPNIDEN_Pos 3U /*!< CoreDebug DAUTHCTRL: INTSPNIDEN, Position */ +#define CoreDebug_DAUTHCTRL_INTSPNIDEN_Msk (1UL << CoreDebug_DAUTHCTRL_INTSPNIDEN_Pos) /*!< CoreDebug DAUTHCTRL: INTSPNIDEN, Mask */ + +#define CoreDebug_DAUTHCTRL_SPNIDENSEL_Pos 2U /*!< CoreDebug DAUTHCTRL: SPNIDENSEL Position */ +#define CoreDebug_DAUTHCTRL_SPNIDENSEL_Msk (1UL << CoreDebug_DAUTHCTRL_SPNIDENSEL_Pos) /*!< CoreDebug DAUTHCTRL: SPNIDENSEL Mask */ + +#define CoreDebug_DAUTHCTRL_INTSPIDEN_Pos 1U /*!< CoreDebug DAUTHCTRL: INTSPIDEN Position */ +#define CoreDebug_DAUTHCTRL_INTSPIDEN_Msk (1UL << CoreDebug_DAUTHCTRL_INTSPIDEN_Pos) /*!< CoreDebug DAUTHCTRL: INTSPIDEN Mask */ + +#define CoreDebug_DAUTHCTRL_SPIDENSEL_Pos 0U /*!< CoreDebug DAUTHCTRL: SPIDENSEL Position */ +#define CoreDebug_DAUTHCTRL_SPIDENSEL_Msk (1UL /*<< CoreDebug_DAUTHCTRL_SPIDENSEL_Pos*/) /*!< CoreDebug DAUTHCTRL: SPIDENSEL Mask */ + +/* Debug Security Control and Status Register Definitions */ +#define CoreDebug_DSCSR_CDS_Pos 16U /*!< CoreDebug DSCSR: CDS Position */ +#define CoreDebug_DSCSR_CDS_Msk (1UL << CoreDebug_DSCSR_CDS_Pos) /*!< CoreDebug DSCSR: CDS Mask */ + +#define CoreDebug_DSCSR_SBRSEL_Pos 1U /*!< CoreDebug DSCSR: SBRSEL Position */ +#define CoreDebug_DSCSR_SBRSEL_Msk (1UL << CoreDebug_DSCSR_SBRSEL_Pos) /*!< CoreDebug DSCSR: SBRSEL Mask */ + +#define CoreDebug_DSCSR_SBRSELEN_Pos 0U /*!< CoreDebug DSCSR: SBRSELEN Position */ +#define CoreDebug_DSCSR_SBRSELEN_Msk (1UL /*<< CoreDebug_DSCSR_SBRSELEN_Pos*/) /*!< CoreDebug DSCSR: SBRSELEN Mask */ + +/*@} end of group CMSIS_CoreDebug */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_core_bitfield Core register bit field macros + \brief Macros for use with bit field definitions (xxx_Pos, xxx_Msk). + @{ + */ + +/** + \brief Mask and shift a bit field value for use in a register bit range. + \param[in] field Name of the register bit field. + \param[in] value Value of the bit field. This parameter is interpreted as an uint32_t type. + \return Masked and shifted value. +*/ +#define _VAL2FLD(field, value) (((uint32_t)(value) << field ## _Pos) & field ## _Msk) + +/** + \brief Mask and shift a register value to extract a bit filed value. + \param[in] field Name of the register bit field. + \param[in] value Value of register. This parameter is interpreted as an uint32_t type. + \return Masked and shifted bit field value. +*/ +#define _FLD2VAL(field, value) (((uint32_t)(value) & field ## _Msk) >> field ## _Pos) + +/*@} end of group CMSIS_core_bitfield */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_core_base Core Definitions + \brief Definitions for base addresses, unions, and structures. + @{ + */ + +/* Memory mapping of Core Hardware */ +#define SCS_BASE (0xE000E000UL) /*!< System Control Space Base Address */ +#define ITM_BASE (0xE0000000UL) /*!< ITM Base Address */ +#define DWT_BASE (0xE0001000UL) /*!< DWT Base Address */ +#define TPI_BASE (0xE0040000UL) /*!< TPI Base Address */ +#define CoreDebug_BASE (0xE000EDF0UL) /*!< Core Debug Base Address */ +#define SysTick_BASE (SCS_BASE + 0x0010UL) /*!< SysTick Base Address */ +#define NVIC_BASE (SCS_BASE + 0x0100UL) /*!< NVIC Base Address */ +#define SCB_BASE (SCS_BASE + 0x0D00UL) /*!< System Control Block Base Address */ + +#define SCnSCB ((SCnSCB_Type *) SCS_BASE ) /*!< System control Register not in SCB */ +#define SCB ((SCB_Type *) SCB_BASE ) /*!< SCB configuration struct */ +#define SysTick ((SysTick_Type *) SysTick_BASE ) /*!< SysTick configuration struct */ +#define NVIC ((NVIC_Type *) NVIC_BASE ) /*!< NVIC configuration struct */ +#define ITM ((ITM_Type *) ITM_BASE ) /*!< ITM configuration struct */ +#define DWT ((DWT_Type *) DWT_BASE ) /*!< DWT configuration struct */ +#define TPI ((TPI_Type *) TPI_BASE ) /*!< TPI configuration struct */ +#define CoreDebug ((CoreDebug_Type *) CoreDebug_BASE ) /*!< Core Debug configuration struct */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) +#define MPU_BASE (SCS_BASE + 0x0D90UL) /*!< Memory Protection Unit */ +#define MPU ((MPU_Type *) MPU_BASE ) /*!< Memory Protection Unit */ +#endif + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +#define SAU_BASE (SCS_BASE + 0x0DD0UL) /*!< Security Attribution Unit */ +#define SAU ((SAU_Type *) SAU_BASE ) /*!< Security Attribution Unit */ +#endif + +#define FPU_BASE (SCS_BASE + 0x0F30UL) /*!< Floating Point Unit */ +#define FPU ((FPU_Type *) FPU_BASE ) /*!< Floating Point Unit */ + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +#define SCS_BASE_NS (0xE002E000UL) /*!< System Control Space Base Address (non-secure address space) */ +#define CoreDebug_BASE_NS (0xE002EDF0UL) /*!< Core Debug Base Address (non-secure address space) */ +#define SysTick_BASE_NS (SCS_BASE_NS + 0x0010UL) /*!< SysTick Base Address (non-secure address space) */ +#define NVIC_BASE_NS (SCS_BASE_NS + 0x0100UL) /*!< NVIC Base Address (non-secure address space) */ +#define SCB_BASE_NS (SCS_BASE_NS + 0x0D00UL) /*!< System Control Block Base Address (non-secure address space) */ + +#define SCnSCB_NS ((SCnSCB_Type *) SCS_BASE_NS ) /*!< System control Register not in SCB(non-secure address space) */ +#define SCB_NS ((SCB_Type *) SCB_BASE_NS ) /*!< SCB configuration struct (non-secure address space) */ +#define SysTick_NS ((SysTick_Type *) SysTick_BASE_NS ) /*!< SysTick configuration struct (non-secure address space) */ +#define NVIC_NS ((NVIC_Type *) NVIC_BASE_NS ) /*!< NVIC configuration struct (non-secure address space) */ +#define CoreDebug_NS ((CoreDebug_Type *) CoreDebug_BASE_NS) /*!< Core Debug configuration struct (non-secure address space) */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) +#define MPU_BASE_NS (SCS_BASE_NS + 0x0D90UL) /*!< Memory Protection Unit (non-secure address space) */ +#define MPU_NS ((MPU_Type *) MPU_BASE_NS ) /*!< Memory Protection Unit (non-secure address space) */ +#endif + +#define FPU_BASE_NS (SCS_BASE_NS + 0x0F30UL) /*!< Floating Point Unit (non-secure address space) */ +#define FPU_NS ((FPU_Type *) FPU_BASE_NS ) /*!< Floating Point Unit (non-secure address space) */ + +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ +/*@} */ + + + +/******************************************************************************* + * Hardware Abstraction Layer + Core Function Interface contains: + - Core NVIC Functions + - Core SysTick Functions + - Core Debug Functions + - Core Register Access Functions + ******************************************************************************/ +/** + \defgroup CMSIS_Core_FunctionInterface Functions and Instructions Reference +*/ + + + +/* ########################## NVIC functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_NVICFunctions NVIC Functions + \brief Functions that manage interrupts and exceptions via the NVIC. + @{ + */ + +#ifdef CMSIS_NVIC_VIRTUAL +#ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE +#define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h" +#endif +#include CMSIS_NVIC_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetPriorityGrouping __NVIC_SetPriorityGrouping +#define NVIC_GetPriorityGrouping __NVIC_GetPriorityGrouping +#define NVIC_EnableIRQ __NVIC_EnableIRQ +#define NVIC_GetEnableIRQ __NVIC_GetEnableIRQ +#define NVIC_DisableIRQ __NVIC_DisableIRQ +#define NVIC_GetPendingIRQ __NVIC_GetPendingIRQ +#define NVIC_SetPendingIRQ __NVIC_SetPendingIRQ +#define NVIC_ClearPendingIRQ __NVIC_ClearPendingIRQ +#define NVIC_GetActive __NVIC_GetActive +#define NVIC_SetPriority __NVIC_SetPriority +#define NVIC_GetPriority __NVIC_GetPriority +#define NVIC_SystemReset __NVIC_SystemReset +#endif /* CMSIS_NVIC_VIRTUAL */ + +#ifdef CMSIS_VECTAB_VIRTUAL +#ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h" +#endif +#include CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetVector __NVIC_SetVector +#define NVIC_GetVector __NVIC_GetVector +#endif /* (CMSIS_VECTAB_VIRTUAL) */ + +#define NVIC_USER_IRQ_OFFSET 16 + + +/* Special LR values for Secure/Non-Secure call handling and exception handling */ + +/* Function Return Payload (from ARMv8-M Architecture Reference Manual) LR value on entry from Secure BLXNS */ +#define FNC_RETURN (0xFEFFFFFFUL) /* bit [0] ignored when processing a branch */ + +/* The following EXC_RETURN mask values are used to evaluate the LR on exception entry */ +#define EXC_RETURN_PREFIX (0xFF000000UL) /* bits [31:24] set to indicate an EXC_RETURN value */ +#define EXC_RETURN_S (0x00000040UL) /* bit [6] stack used to push registers: 0=Non-secure 1=Secure */ +#define EXC_RETURN_DCRS (0x00000020UL) /* bit [5] stacking rules for called registers: 0=skipped 1=saved */ +#define EXC_RETURN_FTYPE (0x00000010UL) /* bit [4] allocate stack for floating-point context: 0=done 1=skipped */ +#define EXC_RETURN_MODE (0x00000008UL) /* bit [3] processor mode for return: 0=Handler mode 1=Thread mode */ +#define EXC_RETURN_SPSEL (0x00000002UL) /* bit [1] stack pointer used to restore context: 0=MSP 1=PSP */ +#define EXC_RETURN_ES (0x00000001UL) /* bit [0] security state exception was taken to: 0=Non-secure 1=Secure */ + +/* Integrity Signature (from ARMv8-M Architecture Reference Manual) for exception context stacking */ +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) /* Value for processors with floating-point extension: */ +#define EXC_INTEGRITY_SIGNATURE (0xFEFA125AUL) /* bit [0] SFTC must match LR bit[4] EXC_RETURN_FTYPE */ +#else +#define EXC_INTEGRITY_SIGNATURE (0xFEFA125BUL) /* Value for processors without floating-point extension */ +#endif + + +/** + \brief Set Priority Grouping + \details Sets the priority grouping field using the required unlock sequence. + The parameter PriorityGroup is assigned to the field SCB->AIRCR [10:8] PRIGROUP field. + Only values from 0..7 are used. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set. + \param [in] PriorityGroup Priority grouping field. + */ +__STATIC_INLINE void __NVIC_SetPriorityGrouping(uint32_t PriorityGroup) +{ + uint32_t reg_value; + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + + reg_value = SCB->AIRCR; /* read old register configuration */ + reg_value &= ~((uint32_t)(SCB_AIRCR_VECTKEY_Msk | SCB_AIRCR_PRIGROUP_Msk)); /* clear bits to change */ + reg_value = (reg_value | + ((uint32_t)0x5FAUL << SCB_AIRCR_VECTKEY_Pos) | + (PriorityGroupTmp << 8U) ); /* Insert write key and priorty group */ + SCB->AIRCR = reg_value; +} + + +/** + \brief Get Priority Grouping + \details Reads the priority grouping field from the NVIC Interrupt Controller. + \return Priority grouping field (SCB->AIRCR [10:8] PRIGROUP field). + */ +__STATIC_INLINE uint32_t __NVIC_GetPriorityGrouping(void) +{ + return ((uint32_t)((SCB->AIRCR & SCB_AIRCR_PRIGROUP_Msk) >> SCB_AIRCR_PRIGROUP_Pos)); +} + + +/** + \brief Enable Interrupt + \details Enables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Interrupt Enable status + \details Returns a device specific interrupt enable status from the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Disable Interrupt + \details Disables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + __DSB(); + __ISB(); + } +} + + +/** + \brief Get Pending Interrupt + \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not pending. + \return 1 Interrupt status is pending. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Pending Interrupt + \details Sets the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Clear Pending Interrupt + \details Clears the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Active Interrupt + \details Reads the active register in the NVIC and returns the active bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not active. + \return 1 Interrupt status is active. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetActive(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->IABR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \brief Get Interrupt Target State + \details Reads the interrupt target field in the NVIC and returns the interrupt target bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 if interrupt is assigned to Secure + \return 1 if interrupt is assigned to Non Secure + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t NVIC_GetTargetState(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Interrupt Target State + \details Sets the interrupt target field in the NVIC and returns the interrupt target bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 if interrupt is assigned to Secure + 1 if interrupt is assigned to Non Secure + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t NVIC_SetTargetState(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] |= ((uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL))); + return ((uint32_t)(((NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Clear Interrupt Target State + \details Clears the interrupt target field in the NVIC and returns the interrupt target bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 if interrupt is assigned to Secure + 1 if interrupt is assigned to Non Secure + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t NVIC_ClearTargetState(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] &= ~((uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL))); + return ((uint32_t)(((NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + + +/** + \brief Set Interrupt Priority + \details Sets the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \param [in] priority Priority to set. + \note The priority cannot be set for every processor exception. + */ +__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->IPR[((uint32_t)IRQn)] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + } + else + { + SCB->SHPR[(((uint32_t)IRQn) & 0xFUL) - 4UL] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + } +} + + +/** + \brief Get Interrupt Priority + \details Reads the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Interrupt Priority. + Value is aligned automatically to the implemented priority bits of the microcontroller. + */ +__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn) +{ + + if ((int32_t)(IRQn) >= 0) + { + return (((uint32_t)NVIC->IPR[((uint32_t)IRQn)] >> (8U - __NVIC_PRIO_BITS))); + } + else + { + return (((uint32_t)SCB->SHPR[(((uint32_t)IRQn) & 0xFUL) - 4UL] >> (8U - __NVIC_PRIO_BITS))); + } +} + + +/** + \brief Encode Priority + \details Encodes the priority for an interrupt with the given priority group, + preemptive priority value, and subpriority value. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set. + \param [in] PriorityGroup Used priority group. + \param [in] PreemptPriority Preemptive priority value (starting from 0). + \param [in] SubPriority Subpriority value (starting from 0). + \return Encoded priority. Value can be used in the function \ref NVIC_SetPriority(). + */ +__STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority) +{ + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + uint32_t PreemptPriorityBits; + uint32_t SubPriorityBits; + + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); + SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + + return ( + ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) | + ((SubPriority & (uint32_t)((1UL << (SubPriorityBits )) - 1UL))) + ); +} + + +/** + \brief Decode Priority + \details Decodes an interrupt priority value with a given priority group to + preemptive priority value and subpriority value. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set. + \param [in] Priority Priority value, which can be retrieved with the function \ref NVIC_GetPriority(). + \param [in] PriorityGroup Used priority group. + \param [out] pPreemptPriority Preemptive priority value (starting from 0). + \param [out] pSubPriority Subpriority value (starting from 0). + */ +__STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* const pPreemptPriority, uint32_t* const pSubPriority) +{ + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + uint32_t PreemptPriorityBits; + uint32_t SubPriorityBits; + + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); + SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + + *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL); + *pSubPriority = (Priority ) & (uint32_t)((1UL << (SubPriorityBits )) - 1UL); +} + + +/** + \brief Set Interrupt Vector + \details Sets an interrupt vector in SRAM based interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + VTOR must been relocated to SRAM before. + \param [in] IRQn Interrupt number + \param [in] vector Address of interrupt handler function + */ +__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector) +{ + uint32_t* vectors = (uint32_t*)SCB->VTOR; + vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector; +} + + +/** + \brief Get Interrupt Vector + \details Reads an interrupt vector from interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Address of interrupt handler function + */ +__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn) +{ + uint32_t* vectors = (uint32_t*)SCB->VTOR; + return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET]; +} + + +/** + \brief System Reset + \details Initiates a system reset request to reset the MCU. + */ +__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void) +{ + __DSB(); /* Ensure all outstanding memory accesses included + buffered write are completed before reset */ + SCB->AIRCR = (uint32_t)((0x5FAUL << SCB_AIRCR_VECTKEY_Pos) | + (SCB->AIRCR & SCB_AIRCR_PRIGROUP_Msk) | + SCB_AIRCR_SYSRESETREQ_Msk ); /* Keep priority group unchanged */ + __DSB(); /* Ensure completion of memory access */ + + for (;;) /* wait until reset */ + { + __NOP(); + } +} + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \brief Set Priority Grouping (non-secure) + \details Sets the non-secure priority grouping field when in secure state using the required unlock sequence. + The parameter PriorityGroup is assigned to the field SCB->AIRCR [10:8] PRIGROUP field. + Only values from 0..7 are used. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set. + \param [in] PriorityGroup Priority grouping field. + */ +__STATIC_INLINE void TZ_NVIC_SetPriorityGrouping_NS(uint32_t PriorityGroup) +{ + uint32_t reg_value; + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + + reg_value = SCB_NS->AIRCR; /* read old register configuration */ + reg_value &= ~((uint32_t)(SCB_AIRCR_VECTKEY_Msk | SCB_AIRCR_PRIGROUP_Msk)); /* clear bits to change */ + reg_value = (reg_value | + ((uint32_t)0x5FAUL << SCB_AIRCR_VECTKEY_Pos) | + (PriorityGroupTmp << 8U) ); /* Insert write key and priorty group */ + SCB_NS->AIRCR = reg_value; +} + + +/** + \brief Get Priority Grouping (non-secure) + \details Reads the priority grouping field from the non-secure NVIC when in secure state. + \return Priority grouping field (SCB->AIRCR [10:8] PRIGROUP field). + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetPriorityGrouping_NS(void) +{ + return ((uint32_t)((SCB_NS->AIRCR & SCB_AIRCR_PRIGROUP_Msk) >> SCB_AIRCR_PRIGROUP_Pos)); +} + + +/** + \brief Enable Interrupt (non-secure) + \details Enables a device specific interrupt in the non-secure NVIC interrupt controller when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_EnableIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ISER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Interrupt Enable status (non-secure) + \details Returns a device specific interrupt enable status from the non-secure NVIC interrupt controller when in secure state. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetEnableIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC_NS->ISER[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Disable Interrupt (non-secure) + \details Disables a device specific interrupt in the non-secure NVIC interrupt controller when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_DisableIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ICER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Pending Interrupt (non-secure) + \details Reads the NVIC pending register in the non-secure NVIC when in secure state and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not pending. + \return 1 Interrupt status is pending. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetPendingIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC_NS->ISPR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Pending Interrupt (non-secure) + \details Sets the pending bit of a device specific interrupt in the non-secure NVIC pending register when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_SetPendingIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ISPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Clear Pending Interrupt (non-secure) + \details Clears the pending bit of a device specific interrupt in the non-secure NVIC pending register when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_ClearPendingIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ICPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Active Interrupt (non-secure) + \details Reads the active register in non-secure NVIC when in secure state and returns the active bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not active. + \return 1 Interrupt status is active. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetActive_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC_NS->IABR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Interrupt Priority (non-secure) + \details Sets the priority of a non-secure device specific interrupt or a non-secure processor exception when in secure state. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \param [in] priority Priority to set. + \note The priority cannot be set for every non-secure processor exception. + */ +__STATIC_INLINE void TZ_NVIC_SetPriority_NS(IRQn_Type IRQn, uint32_t priority) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->IPR[((uint32_t)IRQn)] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + } + else + { + SCB_NS->SHPR[(((uint32_t)IRQn) & 0xFUL) - 4UL] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + } +} + + +/** + \brief Get Interrupt Priority (non-secure) + \details Reads the priority of a non-secure device specific interrupt or a non-secure processor exception when in secure state. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Interrupt Priority. Value is aligned automatically to the implemented priority bits of the microcontroller. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetPriority_NS(IRQn_Type IRQn) +{ + + if ((int32_t)(IRQn) >= 0) + { + return (((uint32_t)NVIC_NS->IPR[((uint32_t)IRQn)] >> (8U - __NVIC_PRIO_BITS))); + } + else + { + return (((uint32_t)SCB_NS->SHPR[(((uint32_t)IRQn) & 0xFUL) - 4UL] >> (8U - __NVIC_PRIO_BITS))); + } +} +#endif /* defined (__ARM_FEATURE_CMSE) &&(__ARM_FEATURE_CMSE == 3U) */ + +/*@} end of CMSIS_Core_NVICFunctions */ + +/* ########################## MPU functions #################################### */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) + +#include "mpu_armv8.h" + +#endif + +/* ########################## FPU functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_FpuFunctions FPU Functions + \brief Function that provides FPU type. + @{ + */ + +/** + \brief get FPU type + \details returns the FPU type + \returns + - \b 0: No FPU + - \b 1: Single precision FPU + - \b 2: Double + Single precision FPU + */ +__STATIC_INLINE uint32_t SCB_GetFPUType(void) +{ + uint32_t mvfr0; + + mvfr0 = FPU->MVFR0; + + if ((mvfr0 & (FPU_MVFR0_Single_precision_Msk | FPU_MVFR0_Double_precision_Msk)) == 0x220U) + { + return 2U; /* Double + Single precision FPU */ + } + else if ((mvfr0 & (FPU_MVFR0_Single_precision_Msk | FPU_MVFR0_Double_precision_Msk)) == 0x020U) + { + return 1U; /* Single precision FPU */ + } + else + { + return 0U; /* No FPU */ + } +} + + +/*@} end of CMSIS_Core_FpuFunctions */ + + + +/* ########################## SAU functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_SAUFunctions SAU Functions + \brief Functions that configure the SAU. + @{ + */ + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) + +/** + \brief Enable SAU + \details Enables the Security Attribution Unit (SAU). + */ +__STATIC_INLINE void TZ_SAU_Enable(void) +{ + SAU->CTRL |= (SAU_CTRL_ENABLE_Msk); +} + + + +/** + \brief Disable SAU + \details Disables the Security Attribution Unit (SAU). + */ +__STATIC_INLINE void TZ_SAU_Disable(void) +{ + SAU->CTRL &= ~(SAU_CTRL_ENABLE_Msk); +} + +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + +/*@} end of CMSIS_Core_SAUFunctions */ + + + + +/* ################################## SysTick function ############################################ */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_SysTickFunctions SysTick Functions + \brief Functions that configure the System. + @{ + */ + +#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U) + +/** + \brief System Tick Configuration + \details Initializes the System Timer and its interrupt, and starts the System Tick Timer. + Counter is in free running mode to generate periodic interrupts. + \param [in] ticks Number of ticks between two interrupts. + \return 0 Function succeeded. + \return 1 Function failed. + \note When the variable __Vendor_SysTickConfig is set to 1, then the + function SysTick_Config is not included. In this case, the file device.h + must contain a vendor-specific implementation of this function. + */ +__STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks) +{ + if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk) + { + return (1UL); /* Reload value impossible */ + } + + SysTick->LOAD = (uint32_t)(ticks - 1UL); /* set reload register */ + NVIC_SetPriority (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */ + SysTick->VAL = 0UL; /* Load the SysTick Counter Value */ + SysTick->CTRL = SysTick_CTRL_CLKSOURCE_Msk | + SysTick_CTRL_TICKINT_Msk | + SysTick_CTRL_ENABLE_Msk; /* Enable SysTick IRQ and SysTick Timer */ + return (0UL); /* Function successful */ +} + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \brief System Tick Configuration (non-secure) + \details Initializes the non-secure System Timer and its interrupt when in secure state, and starts the System Tick Timer. + Counter is in free running mode to generate periodic interrupts. + \param [in] ticks Number of ticks between two interrupts. + \return 0 Function succeeded. + \return 1 Function failed. + \note When the variable __Vendor_SysTickConfig is set to 1, then the + function TZ_SysTick_Config_NS is not included. In this case, the file device.h + must contain a vendor-specific implementation of this function. + + */ +__STATIC_INLINE uint32_t TZ_SysTick_Config_NS(uint32_t ticks) +{ + if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk) + { + return (1UL); /* Reload value impossible */ + } + + SysTick_NS->LOAD = (uint32_t)(ticks - 1UL); /* set reload register */ + TZ_NVIC_SetPriority_NS (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */ + SysTick_NS->VAL = 0UL; /* Load the SysTick Counter Value */ + SysTick_NS->CTRL = SysTick_CTRL_CLKSOURCE_Msk | + SysTick_CTRL_TICKINT_Msk | + SysTick_CTRL_ENABLE_Msk; /* Enable SysTick IRQ and SysTick Timer */ + return (0UL); /* Function successful */ +} +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + +#endif + +/*@} end of CMSIS_Core_SysTickFunctions */ + + + +/* ##################################### Debug In/Output function ########################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_core_DebugFunctions ITM Functions + \brief Functions that access the ITM debug interface. + @{ + */ + +extern volatile int32_t ITM_RxBuffer; /*!< External variable to receive characters. */ +#define ITM_RXBUFFER_EMPTY ((int32_t)0x5AA55AA5U) /*!< Value identifying \ref ITM_RxBuffer is ready for next character. */ + + +/** + \brief ITM Send Character + \details Transmits a character via the ITM channel 0, and + \li Just returns when no debugger is connected that has booked the output. + \li Is blocking when a debugger is connected, but the previous character sent has not been transmitted. + \param [in] ch Character to transmit. + \returns Character to transmit. + */ +__STATIC_INLINE uint32_t ITM_SendChar (uint32_t ch) +{ + if (((ITM->TCR & ITM_TCR_ITMENA_Msk) != 0UL) && /* ITM enabled */ + ((ITM->TER & 1UL ) != 0UL) ) /* ITM Port #0 enabled */ + { + while (ITM->PORT[0U].u32 == 0UL) + { + __NOP(); + } + + ITM->PORT[0U].u8 = (uint8_t)ch; + } + + return (ch); +} + + +/** + \brief ITM Receive Character + \details Inputs a character via the external variable \ref ITM_RxBuffer. + \return Received character. + \return -1 No character pending. + */ +__STATIC_INLINE int32_t ITM_ReceiveChar (void) +{ + int32_t ch = -1; /* no character available */ + + if (ITM_RxBuffer != ITM_RXBUFFER_EMPTY) + { + ch = ITM_RxBuffer; + ITM_RxBuffer = ITM_RXBUFFER_EMPTY; /* ready for next character */ + } + + return (ch); +} + + +/** + \brief ITM Check Character + \details Checks whether a character is pending for reading in the variable \ref ITM_RxBuffer. + \return 0 No character available. + \return 1 Character available. + */ +__STATIC_INLINE int32_t ITM_CheckChar (void) +{ + + if (ITM_RxBuffer == ITM_RXBUFFER_EMPTY) + { + return (0); /* no character available */ + } + else + { + return (1); /* character available */ + } +} + +/*@} end of CMSIS_core_DebugFunctions */ + + + + +#ifdef __cplusplus +} +#endif + +#endif /* __CORE_ARMV8MML_H_DEPENDANT */ + +#endif /* __CMSIS_GENERIC */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/core_cm0.h b/EpsilonLights/Drivers/CMSIS/Include/core_cm0.h index f3824030..0757cee6 100644 --- a/EpsilonLights/Drivers/CMSIS/Include/core_cm0.h +++ b/EpsilonLights/Drivers/CMSIS/Include/core_cm0.h @@ -1,40 +1,30 @@ /**************************************************************************//** * @file core_cm0.h * @brief CMSIS Cortex-M0 Core Peripheral Access Layer Header File - * @version V4.30 - * @date 20. October 2015 + * @version V5.0.5 + * @date 28. May 2018 ******************************************************************************/ -/* Copyright (c) 2009 - 2015 ARM LIMITED - - All rights reserved. - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - - Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - - Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - Neither the name of ARM nor the names of its contributors may be used - to endorse or promote products derived from this software without - specific prior written permission. - * - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE - LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR - CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF - SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS - INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN - CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) - ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE - POSSIBILITY OF SUCH DAMAGE. - ---------------------------------------------------------------------------*/ - +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ #if defined ( __ICCARM__ ) #pragma system_include /* treat file as system include file for MISRA check */ -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#elif defined (__clang__) #pragma clang system_header /* treat file as system include file */ #endif @@ -70,53 +60,15 @@ extern "C" { @{ */ +#include "cmsis_version.h" + /* CMSIS CM0 definitions */ -#define __CM0_CMSIS_VERSION_MAIN (0x04U) /*!< [31:16] CMSIS HAL main version */ -#define __CM0_CMSIS_VERSION_SUB (0x1EU) /*!< [15:0] CMSIS HAL sub version */ +#define __CM0_CMSIS_VERSION_MAIN (__CM_CMSIS_VERSION_MAIN) /*!< \deprecated [31:16] CMSIS HAL main version */ +#define __CM0_CMSIS_VERSION_SUB (__CM_CMSIS_VERSION_SUB) /*!< \deprecated [15:0] CMSIS HAL sub version */ #define __CM0_CMSIS_VERSION ((__CM0_CMSIS_VERSION_MAIN << 16U) | \ - __CM0_CMSIS_VERSION_SUB ) /*!< CMSIS HAL version number */ - -#define __CORTEX_M (0x00U) /*!< Cortex-M Core */ - - -#if defined ( __CC_ARM ) -#define __ASM __asm /*!< asm keyword for ARM Compiler */ -#define __INLINE __inline /*!< inline keyword for ARM Compiler */ -#define __STATIC_INLINE static __inline - -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) -#define __ASM __asm /*!< asm keyword for ARM Compiler */ -#define __INLINE __inline /*!< inline keyword for ARM Compiler */ -#define __STATIC_INLINE static __inline - -#elif defined ( __GNUC__ ) -#define __ASM __asm /*!< asm keyword for GNU Compiler */ -#define __INLINE inline /*!< inline keyword for GNU Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __ICCARM__ ) -#define __ASM __asm /*!< asm keyword for IAR Compiler */ -#define __INLINE inline /*!< inline keyword for IAR Compiler. Only available in High optimization mode! */ -#define __STATIC_INLINE static inline - -#elif defined ( __TMS470__ ) -#define __ASM __asm /*!< asm keyword for TI CCS Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __TASKING__ ) -#define __ASM __asm /*!< asm keyword for TASKING Compiler */ -#define __INLINE inline /*!< inline keyword for TASKING Compiler */ -#define __STATIC_INLINE static inline + __CM0_CMSIS_VERSION_SUB ) /*!< \deprecated CMSIS HAL version number */ -#elif defined ( __CSMC__ ) -#define __packed -#define __ASM _asm /*!< asm keyword for COSMIC Compiler */ -#define __INLINE inline /*!< inline keyword for COSMIC Compiler. Use -pc99 on compile line */ -#define __STATIC_INLINE static inline - -#else -#error Unknown compiler -#endif +#define __CORTEX_M (0U) /*!< Cortex-M Core */ /** __FPU_USED indicates whether an FPU is used or not. This core does not support an FPU at all @@ -128,7 +80,7 @@ extern "C" { #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) #if defined __ARM_PCS_VFP #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif @@ -143,7 +95,7 @@ extern "C" { #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif -#elif defined ( __TMS470__ ) +#elif defined ( __TI_ARM__ ) #if defined __TI_VFP_SUPPORT__ #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif @@ -160,8 +112,8 @@ extern "C" { #endif -#include "core_cmInstr.h" /* Core Instruction Access */ -#include "core_cmFunc.h" /* Core Function Access */ +#include "cmsis_compiler.h" /* CMSIS compiler specific defines */ + #ifdef __cplusplus } @@ -555,18 +507,18 @@ typedef struct /** \brief Mask and shift a bit field value for use in a register bit range. \param[in] field Name of the register bit field. - \param[in] value Value of the bit field. + \param[in] value Value of the bit field. This parameter is interpreted as an uint32_t type. \return Masked and shifted value. */ -#define _VAL2FLD(field, value) ((value << field ## _Pos) & field ## _Msk) +#define _VAL2FLD(field, value) (((uint32_t)(value) << field ## _Pos) & field ## _Msk) /** \brief Mask and shift a register value to extract a bit filed value. \param[in] field Name of the register bit field. - \param[in] value Value of register. + \param[in] value Value of register. This parameter is interpreted as an uint32_t type. \return Masked and shifted bit field value. */ -#define _FLD2VAL(field, value) ((value & field ## _Msk) >> field ## _Pos) +#define _FLD2VAL(field, value) (((uint32_t)(value) & field ## _Msk) >> field ## _Pos) /*@} end of group CMSIS_core_bitfield */ @@ -578,7 +530,7 @@ typedef struct @{ */ -/* Memory mapping of Cortex-M0 Hardware */ +/* Memory mapping of Core Hardware */ #define SCS_BASE (0xE000E000UL) /*!< System Control Space Base Address */ #define SysTick_BASE (SCS_BASE + 0x0010UL) /*!< SysTick Base Address */ #define NVIC_BASE (SCS_BASE + 0x0100UL) /*!< NVIC Base Address */ @@ -614,87 +566,177 @@ typedef struct @{ */ -/* Interrupt Priorities are WORD accessible only under ARMv6M */ +#ifdef CMSIS_NVIC_VIRTUAL +#ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE +#define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h" +#endif +#include CMSIS_NVIC_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetPriorityGrouping __NVIC_SetPriorityGrouping +#define NVIC_GetPriorityGrouping __NVIC_GetPriorityGrouping +#define NVIC_EnableIRQ __NVIC_EnableIRQ +#define NVIC_GetEnableIRQ __NVIC_GetEnableIRQ +#define NVIC_DisableIRQ __NVIC_DisableIRQ +#define NVIC_GetPendingIRQ __NVIC_GetPendingIRQ +#define NVIC_SetPendingIRQ __NVIC_SetPendingIRQ +#define NVIC_ClearPendingIRQ __NVIC_ClearPendingIRQ +/*#define NVIC_GetActive __NVIC_GetActive not available for Cortex-M0 */ +#define NVIC_SetPriority __NVIC_SetPriority +#define NVIC_GetPriority __NVIC_GetPriority +#define NVIC_SystemReset __NVIC_SystemReset +#endif /* CMSIS_NVIC_VIRTUAL */ + +#ifdef CMSIS_VECTAB_VIRTUAL +#ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h" +#endif +#include CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetVector __NVIC_SetVector +#define NVIC_GetVector __NVIC_GetVector +#endif /* (CMSIS_VECTAB_VIRTUAL) */ + +#define NVIC_USER_IRQ_OFFSET 16 + + +/* The following EXC_RETURN values are saved the LR on exception entry */ +#define EXC_RETURN_HANDLER (0xFFFFFFF1UL) /* return to Handler mode, uses MSP after return */ +#define EXC_RETURN_THREAD_MSP (0xFFFFFFF9UL) /* return to Thread mode, uses MSP after return */ +#define EXC_RETURN_THREAD_PSP (0xFFFFFFFDUL) /* return to Thread mode, uses PSP after return */ + + +/* Interrupt Priorities are WORD accessible only under Armv6-M */ /* The following MACROS handle generation of the register offset and byte masks */ #define _BIT_SHIFT(IRQn) ( ((((uint32_t)(int32_t)(IRQn)) ) & 0x03UL) * 8UL) #define _SHP_IDX(IRQn) ( (((((uint32_t)(int32_t)(IRQn)) & 0x0FUL)-8UL) >> 2UL) ) #define _IP_IDX(IRQn) ( (((uint32_t)(int32_t)(IRQn)) >> 2UL) ) +#define __NVIC_SetPriorityGrouping(X) (void)(X) +#define __NVIC_GetPriorityGrouping() (0U) /** - \brief Enable External Interrupt - \details Enables a device-specific interrupt in the NVIC interrupt controller. - \param [in] IRQn External interrupt number. Value cannot be negative. + \brief Enable Interrupt + \details Enables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_EnableIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn) { - NVIC->ISER[0U] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Interrupt Enable status + \details Returns a device specific interrupt enable status from the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISER[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** - \brief Disable External Interrupt - \details Disables a device-specific interrupt in the NVIC interrupt controller. - \param [in] IRQn External interrupt number. Value cannot be negative. + \brief Disable Interrupt + \details Disables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_DisableIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn) { - NVIC->ICER[0U] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + __DSB(); + __ISB(); + } } /** \brief Get Pending Interrupt - \details Reads the pending register in the NVIC and returns the pending bit for the specified interrupt. - \param [in] IRQn Interrupt number. + \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. \return 0 Interrupt status is not pending. \return 1 Interrupt status is pending. + \note IRQn must not be negative. */ -__STATIC_INLINE uint32_t NVIC_GetPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn) { - return ((uint32_t)(((NVIC->ISPR[0U] & (1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISPR[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** \brief Set Pending Interrupt - \details Sets the pending bit of an external interrupt. - \param [in] IRQn Interrupt number. Value cannot be negative. + \details Sets the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_SetPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn) { - NVIC->ISPR[0U] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** \brief Clear Pending Interrupt - \details Clears the pending bit of an external interrupt. - \param [in] IRQn External interrupt number. Value cannot be negative. + \details Clears the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_ClearPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn) { - NVIC->ICPR[0U] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** \brief Set Interrupt Priority - \details Sets the priority of an interrupt. - \note The priority cannot be set for every core interrupt. + \details Sets the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. \param [in] IRQn Interrupt number. \param [in] priority Priority to set. + \note The priority cannot be set for every processor exception. */ -__STATIC_INLINE void NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) +__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) { - if ((int32_t)(IRQn) < 0) + if ((int32_t)(IRQn) >= 0) { - SCB->SHP[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHP[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + NVIC->IP[_IP_IDX(IRQn)] = ((uint32_t)(NVIC->IP[_IP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); } else { - NVIC->IP[_IP_IDX(IRQn)] = ((uint32_t)(NVIC->IP[_IP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + SCB->SHP[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHP[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); } } @@ -702,31 +744,116 @@ __STATIC_INLINE void NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) /** \brief Get Interrupt Priority - \details Reads the priority of an interrupt. - The interrupt number can be positive to specify an external (device specific) interrupt, - or negative to specify an internal (core) interrupt. + \details Reads the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. \param [in] IRQn Interrupt number. \return Interrupt Priority. Value is aligned automatically to the implemented priority bits of the microcontroller. */ -__STATIC_INLINE uint32_t NVIC_GetPriority(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn) { - if ((int32_t)(IRQn) < 0) + + if ((int32_t)(IRQn) >= 0) { - return ((uint32_t)(((SCB->SHP[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + return ((uint32_t)(((NVIC->IP[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); } else { - return ((uint32_t)(((NVIC->IP[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + return ((uint32_t)(((SCB->SHP[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); } } +/** + \brief Encode Priority + \details Encodes the priority for an interrupt with the given priority group, + preemptive priority value, and subpriority value. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set. + \param [in] PriorityGroup Used priority group. + \param [in] PreemptPriority Preemptive priority value (starting from 0). + \param [in] SubPriority Subpriority value (starting from 0). + \return Encoded priority. Value can be used in the function \ref NVIC_SetPriority(). + */ +__STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority) +{ + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + uint32_t PreemptPriorityBits; + uint32_t SubPriorityBits; + + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); + SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + + return ( + ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) | + ((SubPriority & (uint32_t)((1UL << (SubPriorityBits )) - 1UL))) + ); +} + + +/** + \brief Decode Priority + \details Decodes an interrupt priority value with a given priority group to + preemptive priority value and subpriority value. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set. + \param [in] Priority Priority value, which can be retrieved with the function \ref NVIC_GetPriority(). + \param [in] PriorityGroup Used priority group. + \param [out] pPreemptPriority Preemptive priority value (starting from 0). + \param [out] pSubPriority Subpriority value (starting from 0). + */ +__STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* const pPreemptPriority, uint32_t* const pSubPriority) +{ + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + uint32_t PreemptPriorityBits; + uint32_t SubPriorityBits; + + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); + SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + + *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL); + *pSubPriority = (Priority ) & (uint32_t)((1UL << (SubPriorityBits )) - 1UL); +} + + + +/** + \brief Set Interrupt Vector + \details Sets an interrupt vector in SRAM based interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + Address 0 must be mapped to SRAM. + \param [in] IRQn Interrupt number + \param [in] vector Address of interrupt handler function + */ +__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector) +{ + uint32_t* vectors = (uint32_t*)0x0U; + vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector; +} + + +/** + \brief Get Interrupt Vector + \details Reads an interrupt vector from interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Address of interrupt handler function + */ +__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn) +{ + uint32_t* vectors = (uint32_t*)0x0U; + return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET]; +} + + /** \brief System Reset \details Initiates a system reset request to reset the MCU. */ -__STATIC_INLINE void NVIC_SystemReset(void) +__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void) { __DSB(); /* Ensure all outstanding memory accesses included buffered write are completed before reset */ @@ -743,6 +870,31 @@ __STATIC_INLINE void NVIC_SystemReset(void) /*@} end of CMSIS_Core_NVICFunctions */ +/* ########################## FPU functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_FpuFunctions FPU Functions + \brief Function that provides FPU type. + @{ + */ + +/** + \brief get FPU type + \details returns the FPU type + \returns + - \b 0: No FPU + - \b 1: Single precision FPU + - \b 2: Double + Single precision FPU + */ +__STATIC_INLINE uint32_t SCB_GetFPUType(void) +{ + return 0U; /* No FPU */ +} + + +/*@} end of CMSIS_Core_FpuFunctions */ + + /* ################################## SysTick function ############################################ */ /** @@ -752,7 +904,7 @@ __STATIC_INLINE void NVIC_SystemReset(void) @{ */ -#if (__Vendor_SysTickConfig == 0U) +#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U) /** \brief System Tick Configuration diff --git a/EpsilonLights/Drivers/CMSIS/Include/core_cm0plus.h b/EpsilonLights/Drivers/CMSIS/Include/core_cm0plus.h index 014b19d1..97eb1c39 100644 --- a/EpsilonLights/Drivers/CMSIS/Include/core_cm0plus.h +++ b/EpsilonLights/Drivers/CMSIS/Include/core_cm0plus.h @@ -1,40 +1,30 @@ /**************************************************************************//** * @file core_cm0plus.h * @brief CMSIS Cortex-M0+ Core Peripheral Access Layer Header File - * @version V4.30 - * @date 20. October 2015 + * @version V5.0.6 + * @date 28. May 2018 ******************************************************************************/ -/* Copyright (c) 2009 - 2015 ARM LIMITED - - All rights reserved. - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - - Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - - Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - Neither the name of ARM nor the names of its contributors may be used - to endorse or promote products derived from this software without - specific prior written permission. - * - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE - LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR - CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF - SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS - INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN - CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) - ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE - POSSIBILITY OF SUCH DAMAGE. - ---------------------------------------------------------------------------*/ - +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ #if defined ( __ICCARM__ ) #pragma system_include /* treat file as system include file for MISRA check */ -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#elif defined (__clang__) #pragma clang system_header /* treat file as system include file */ #endif @@ -70,53 +60,15 @@ extern "C" { @{ */ +#include "cmsis_version.h" + /* CMSIS CM0+ definitions */ -#define __CM0PLUS_CMSIS_VERSION_MAIN (0x04U) /*!< [31:16] CMSIS HAL main version */ -#define __CM0PLUS_CMSIS_VERSION_SUB (0x1EU) /*!< [15:0] CMSIS HAL sub version */ +#define __CM0PLUS_CMSIS_VERSION_MAIN (__CM_CMSIS_VERSION_MAIN) /*!< \deprecated [31:16] CMSIS HAL main version */ +#define __CM0PLUS_CMSIS_VERSION_SUB (__CM_CMSIS_VERSION_SUB) /*!< \deprecated [15:0] CMSIS HAL sub version */ #define __CM0PLUS_CMSIS_VERSION ((__CM0PLUS_CMSIS_VERSION_MAIN << 16U) | \ - __CM0PLUS_CMSIS_VERSION_SUB ) /*!< CMSIS HAL version number */ - -#define __CORTEX_M (0x00U) /*!< Cortex-M Core */ + __CM0PLUS_CMSIS_VERSION_SUB ) /*!< \deprecated CMSIS HAL version number */ - -#if defined ( __CC_ARM ) -#define __ASM __asm /*!< asm keyword for ARM Compiler */ -#define __INLINE __inline /*!< inline keyword for ARM Compiler */ -#define __STATIC_INLINE static __inline - -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) -#define __ASM __asm /*!< asm keyword for ARM Compiler */ -#define __INLINE __inline /*!< inline keyword for ARM Compiler */ -#define __STATIC_INLINE static __inline - -#elif defined ( __GNUC__ ) -#define __ASM __asm /*!< asm keyword for GNU Compiler */ -#define __INLINE inline /*!< inline keyword for GNU Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __ICCARM__ ) -#define __ASM __asm /*!< asm keyword for IAR Compiler */ -#define __INLINE inline /*!< inline keyword for IAR Compiler. Only available in High optimization mode! */ -#define __STATIC_INLINE static inline - -#elif defined ( __TMS470__ ) -#define __ASM __asm /*!< asm keyword for TI CCS Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __TASKING__ ) -#define __ASM __asm /*!< asm keyword for TASKING Compiler */ -#define __INLINE inline /*!< inline keyword for TASKING Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __CSMC__ ) -#define __packed -#define __ASM _asm /*!< asm keyword for COSMIC Compiler */ -#define __INLINE inline /*!< inline keyword for COSMIC Compiler. Use -pc99 on compile line */ -#define __STATIC_INLINE static inline - -#else -#error Unknown compiler -#endif +#define __CORTEX_M (0U) /*!< Cortex-M Core */ /** __FPU_USED indicates whether an FPU is used or not. This core does not support an FPU at all @@ -128,7 +80,7 @@ extern "C" { #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) #if defined __ARM_PCS_VFP #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif @@ -143,7 +95,7 @@ extern "C" { #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif -#elif defined ( __TMS470__ ) +#elif defined ( __TI_ARM__ ) #if defined __TI_VFP_SUPPORT__ #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif @@ -160,8 +112,8 @@ extern "C" { #endif -#include "core_cmInstr.h" /* Core Instruction Access */ -#include "core_cmFunc.h" /* Core Function Access */ +#include "cmsis_compiler.h" /* CMSIS compiler specific defines */ + #ifdef __cplusplus } @@ -404,7 +356,7 @@ typedef struct { __IM uint32_t CPUID; /*!< Offset: 0x000 (R/ ) CPUID Base Register */ __IOM uint32_t ICSR; /*!< Offset: 0x004 (R/W) Interrupt Control and State Register */ -#if (__VTOR_PRESENT == 1U) +#if defined (__VTOR_PRESENT) && (__VTOR_PRESENT == 1U) __IOM uint32_t VTOR; /*!< Offset: 0x008 (R/W) Vector Table Offset Register */ #else uint32_t RESERVED0; @@ -461,7 +413,7 @@ typedef struct #define SCB_ICSR_VECTACTIVE_Pos 0U /*!< SCB ICSR: VECTACTIVE Position */ #define SCB_ICSR_VECTACTIVE_Msk (0x1FFUL /*<< SCB_ICSR_VECTACTIVE_Pos*/) /*!< SCB ICSR: VECTACTIVE Mask */ -#if (__VTOR_PRESENT == 1U) +#if defined (__VTOR_PRESENT) && (__VTOR_PRESENT == 1U) /* SCB Interrupt Control State Register Definitions */ #define SCB_VTOR_TBLOFF_Pos 8U /*!< SCB VTOR: TBLOFF Position */ #define SCB_VTOR_TBLOFF_Msk (0xFFFFFFUL << SCB_VTOR_TBLOFF_Pos) /*!< SCB VTOR: TBLOFF Mask */ @@ -558,7 +510,7 @@ typedef struct /*@} end of group CMSIS_SysTick */ -#if (__MPU_PRESENT == 1U) +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) /** \ingroup CMSIS_core_register \defgroup CMSIS_MPU Memory Protection Unit (MPU) @@ -578,6 +530,8 @@ typedef struct __IOM uint32_t RASR; /*!< Offset: 0x010 (R/W) MPU Region Attribute and Size Register */ } MPU_Type; +#define MPU_TYPE_RALIASES 1U + /* MPU Type Register Definitions */ #define MPU_TYPE_IREGION_Pos 16U /*!< MPU TYPE: IREGION Position */ #define MPU_TYPE_IREGION_Msk (0xFFUL << MPU_TYPE_IREGION_Pos) /*!< MPU TYPE: IREGION Mask */ @@ -667,18 +621,18 @@ typedef struct /** \brief Mask and shift a bit field value for use in a register bit range. \param[in] field Name of the register bit field. - \param[in] value Value of the bit field. + \param[in] value Value of the bit field. This parameter is interpreted as an uint32_t type. \return Masked and shifted value. */ -#define _VAL2FLD(field, value) ((value << field ## _Pos) & field ## _Msk) +#define _VAL2FLD(field, value) (((uint32_t)(value) << field ## _Pos) & field ## _Msk) /** \brief Mask and shift a register value to extract a bit filed value. \param[in] field Name of the register bit field. - \param[in] value Value of register. + \param[in] value Value of register. This parameter is interpreted as an uint32_t type. \return Masked and shifted bit field value. */ -#define _FLD2VAL(field, value) ((value & field ## _Msk) >> field ## _Pos) +#define _FLD2VAL(field, value) (((uint32_t)(value) & field ## _Msk) >> field ## _Pos) /*@} end of group CMSIS_core_bitfield */ @@ -690,7 +644,7 @@ typedef struct @{ */ -/* Memory mapping of Cortex-M0+ Hardware */ +/* Memory mapping of Core Hardware */ #define SCS_BASE (0xE000E000UL) /*!< System Control Space Base Address */ #define SysTick_BASE (SCS_BASE + 0x0010UL) /*!< SysTick Base Address */ #define NVIC_BASE (SCS_BASE + 0x0100UL) /*!< NVIC Base Address */ @@ -700,7 +654,7 @@ typedef struct #define SysTick ((SysTick_Type *) SysTick_BASE ) /*!< SysTick configuration struct */ #define NVIC ((NVIC_Type *) NVIC_BASE ) /*!< NVIC configuration struct */ -#if (__MPU_PRESENT == 1U) +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) #define MPU_BASE (SCS_BASE + 0x0D90UL) /*!< Memory Protection Unit */ #define MPU ((MPU_Type *) MPU_BASE ) /*!< Memory Protection Unit */ #endif @@ -730,87 +684,177 @@ typedef struct @{ */ -/* Interrupt Priorities are WORD accessible only under ARMv6M */ +#ifdef CMSIS_NVIC_VIRTUAL +#ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE +#define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h" +#endif +#include CMSIS_NVIC_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetPriorityGrouping __NVIC_SetPriorityGrouping +#define NVIC_GetPriorityGrouping __NVIC_GetPriorityGrouping +#define NVIC_EnableIRQ __NVIC_EnableIRQ +#define NVIC_GetEnableIRQ __NVIC_GetEnableIRQ +#define NVIC_DisableIRQ __NVIC_DisableIRQ +#define NVIC_GetPendingIRQ __NVIC_GetPendingIRQ +#define NVIC_SetPendingIRQ __NVIC_SetPendingIRQ +#define NVIC_ClearPendingIRQ __NVIC_ClearPendingIRQ +/*#define NVIC_GetActive __NVIC_GetActive not available for Cortex-M0+ */ +#define NVIC_SetPriority __NVIC_SetPriority +#define NVIC_GetPriority __NVIC_GetPriority +#define NVIC_SystemReset __NVIC_SystemReset +#endif /* CMSIS_NVIC_VIRTUAL */ + +#ifdef CMSIS_VECTAB_VIRTUAL +#ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h" +#endif +#include CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetVector __NVIC_SetVector +#define NVIC_GetVector __NVIC_GetVector +#endif /* (CMSIS_VECTAB_VIRTUAL) */ + +#define NVIC_USER_IRQ_OFFSET 16 + + +/* The following EXC_RETURN values are saved the LR on exception entry */ +#define EXC_RETURN_HANDLER (0xFFFFFFF1UL) /* return to Handler mode, uses MSP after return */ +#define EXC_RETURN_THREAD_MSP (0xFFFFFFF9UL) /* return to Thread mode, uses MSP after return */ +#define EXC_RETURN_THREAD_PSP (0xFFFFFFFDUL) /* return to Thread mode, uses PSP after return */ + + +/* Interrupt Priorities are WORD accessible only under Armv6-M */ /* The following MACROS handle generation of the register offset and byte masks */ #define _BIT_SHIFT(IRQn) ( ((((uint32_t)(int32_t)(IRQn)) ) & 0x03UL) * 8UL) #define _SHP_IDX(IRQn) ( (((((uint32_t)(int32_t)(IRQn)) & 0x0FUL)-8UL) >> 2UL) ) #define _IP_IDX(IRQn) ( (((uint32_t)(int32_t)(IRQn)) >> 2UL) ) +#define __NVIC_SetPriorityGrouping(X) (void)(X) +#define __NVIC_GetPriorityGrouping() (0U) /** - \brief Enable External Interrupt - \details Enables a device-specific interrupt in the NVIC interrupt controller. - \param [in] IRQn External interrupt number. Value cannot be negative. + \brief Enable Interrupt + \details Enables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_EnableIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn) { - NVIC->ISER[0U] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Interrupt Enable status + \details Returns a device specific interrupt enable status from the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISER[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** - \brief Disable External Interrupt - \details Disables a device-specific interrupt in the NVIC interrupt controller. - \param [in] IRQn External interrupt number. Value cannot be negative. + \brief Disable Interrupt + \details Disables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_DisableIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn) { - NVIC->ICER[0U] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + __DSB(); + __ISB(); + } } /** \brief Get Pending Interrupt - \details Reads the pending register in the NVIC and returns the pending bit for the specified interrupt. - \param [in] IRQn Interrupt number. + \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. \return 0 Interrupt status is not pending. \return 1 Interrupt status is pending. + \note IRQn must not be negative. */ -__STATIC_INLINE uint32_t NVIC_GetPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn) { - return ((uint32_t)(((NVIC->ISPR[0U] & (1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISPR[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** \brief Set Pending Interrupt - \details Sets the pending bit of an external interrupt. - \param [in] IRQn Interrupt number. Value cannot be negative. + \details Sets the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_SetPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn) { - NVIC->ISPR[0U] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** \brief Clear Pending Interrupt - \details Clears the pending bit of an external interrupt. - \param [in] IRQn External interrupt number. Value cannot be negative. + \details Clears the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_ClearPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn) { - NVIC->ICPR[0U] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** \brief Set Interrupt Priority - \details Sets the priority of an interrupt. - \note The priority cannot be set for every core interrupt. + \details Sets the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. \param [in] IRQn Interrupt number. \param [in] priority Priority to set. + \note The priority cannot be set for every processor exception. */ -__STATIC_INLINE void NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) +__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) { - if ((int32_t)(IRQn) < 0) + if ((int32_t)(IRQn) >= 0) { - SCB->SHP[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHP[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + NVIC->IP[_IP_IDX(IRQn)] = ((uint32_t)(NVIC->IP[_IP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); } else { - NVIC->IP[_IP_IDX(IRQn)] = ((uint32_t)(NVIC->IP[_IP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + SCB->SHP[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHP[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); } } @@ -818,31 +862,125 @@ __STATIC_INLINE void NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) /** \brief Get Interrupt Priority - \details Reads the priority of an interrupt. - The interrupt number can be positive to specify an external (device specific) interrupt, - or negative to specify an internal (core) interrupt. + \details Reads the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. \param [in] IRQn Interrupt number. \return Interrupt Priority. Value is aligned automatically to the implemented priority bits of the microcontroller. */ -__STATIC_INLINE uint32_t NVIC_GetPriority(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn) { - if ((int32_t)(IRQn) < 0) + + if ((int32_t)(IRQn) >= 0) { - return ((uint32_t)(((SCB->SHP[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + return ((uint32_t)(((NVIC->IP[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); } else { - return ((uint32_t)(((NVIC->IP[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + return ((uint32_t)(((SCB->SHP[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); } } +/** + \brief Encode Priority + \details Encodes the priority for an interrupt with the given priority group, + preemptive priority value, and subpriority value. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set. + \param [in] PriorityGroup Used priority group. + \param [in] PreemptPriority Preemptive priority value (starting from 0). + \param [in] SubPriority Subpriority value (starting from 0). + \return Encoded priority. Value can be used in the function \ref NVIC_SetPriority(). + */ +__STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority) +{ + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + uint32_t PreemptPriorityBits; + uint32_t SubPriorityBits; + + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); + SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + + return ( + ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) | + ((SubPriority & (uint32_t)((1UL << (SubPriorityBits )) - 1UL))) + ); +} + + +/** + \brief Decode Priority + \details Decodes an interrupt priority value with a given priority group to + preemptive priority value and subpriority value. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set. + \param [in] Priority Priority value, which can be retrieved with the function \ref NVIC_GetPriority(). + \param [in] PriorityGroup Used priority group. + \param [out] pPreemptPriority Preemptive priority value (starting from 0). + \param [out] pSubPriority Subpriority value (starting from 0). + */ +__STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* const pPreemptPriority, uint32_t* const pSubPriority) +{ + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + uint32_t PreemptPriorityBits; + uint32_t SubPriorityBits; + + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); + SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + + *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL); + *pSubPriority = (Priority ) & (uint32_t)((1UL << (SubPriorityBits )) - 1UL); +} + + +/** + \brief Set Interrupt Vector + \details Sets an interrupt vector in SRAM based interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + VTOR must been relocated to SRAM before. + If VTOR is not present address 0 must be mapped to SRAM. + \param [in] IRQn Interrupt number + \param [in] vector Address of interrupt handler function + */ +__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector) +{ +#if defined (__VTOR_PRESENT) && (__VTOR_PRESENT == 1U) + uint32_t* vectors = (uint32_t*)SCB->VTOR; +#else + uint32_t* vectors = (uint32_t*)0x0U; +#endif + vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector; +} + + +/** + \brief Get Interrupt Vector + \details Reads an interrupt vector from interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Address of interrupt handler function + */ +__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn) +{ +#if defined (__VTOR_PRESENT) && (__VTOR_PRESENT == 1U) + uint32_t* vectors = (uint32_t*)SCB->VTOR; +#else + uint32_t* vectors = (uint32_t*)0x0U; +#endif + return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET]; + +} + + /** \brief System Reset \details Initiates a system reset request to reset the MCU. */ -__STATIC_INLINE void NVIC_SystemReset(void) +__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void) { __DSB(); /* Ensure all outstanding memory accesses included buffered write are completed before reset */ @@ -858,6 +996,38 @@ __STATIC_INLINE void NVIC_SystemReset(void) /*@} end of CMSIS_Core_NVICFunctions */ +/* ########################## MPU functions #################################### */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) + +#include "mpu_armv7.h" + +#endif + +/* ########################## FPU functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_FpuFunctions FPU Functions + \brief Function that provides FPU type. + @{ + */ + +/** + \brief get FPU type + \details returns the FPU type + \returns + - \b 0: No FPU + - \b 1: Single precision FPU + - \b 2: Double + Single precision FPU + */ +__STATIC_INLINE uint32_t SCB_GetFPUType(void) +{ + return 0U; /* No FPU */ +} + + +/*@} end of CMSIS_Core_FpuFunctions */ + /* ################################## SysTick function ############################################ */ @@ -868,7 +1038,7 @@ __STATIC_INLINE void NVIC_SystemReset(void) @{ */ -#if (__Vendor_SysTickConfig == 0U) +#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U) /** \brief System Tick Configuration diff --git a/EpsilonLights/Drivers/CMSIS/Include/core_cm1.h b/EpsilonLights/Drivers/CMSIS/Include/core_cm1.h new file mode 100644 index 00000000..6a3926cb --- /dev/null +++ b/EpsilonLights/Drivers/CMSIS/Include/core_cm1.h @@ -0,0 +1,976 @@ +/**************************************************************************//** + * @file core_cm1.h + * @brief CMSIS Cortex-M1 Core Peripheral Access Layer Header File + * @version V1.0.0 + * @date 23. July 2018 + ******************************************************************************/ +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ + +#if defined ( __ICCARM__ ) +#pragma system_include /* treat file as system include file for MISRA check */ +#elif defined (__clang__) +#pragma clang system_header /* treat file as system include file */ +#endif + +#ifndef __CORE_CM1_H_GENERIC +#define __CORE_CM1_H_GENERIC + +#include + +#ifdef __cplusplus +extern "C" { +#endif + +/** + \page CMSIS_MISRA_Exceptions MISRA-C:2004 Compliance Exceptions + CMSIS violates the following MISRA-C:2004 rules: + + \li Required Rule 8.5, object/function definition in header file.
+ Function definitions in header files are used to allow 'inlining'. + + \li Required Rule 18.4, declaration of union type or object of union type: '{...}'.
+ Unions are used for effective representation of core registers. + + \li Advisory Rule 19.7, Function-like macro defined.
+ Function-like macros are used to allow more efficient code. + */ + + +/******************************************************************************* + * CMSIS definitions + ******************************************************************************/ +/** + \ingroup Cortex_M1 + @{ + */ + +#include "cmsis_version.h" + +/* CMSIS CM1 definitions */ +#define __CM1_CMSIS_VERSION_MAIN (__CM_CMSIS_VERSION_MAIN) /*!< \deprecated [31:16] CMSIS HAL main version */ +#define __CM1_CMSIS_VERSION_SUB (__CM_CMSIS_VERSION_SUB) /*!< \deprecated [15:0] CMSIS HAL sub version */ +#define __CM1_CMSIS_VERSION ((__CM1_CMSIS_VERSION_MAIN << 16U) | \ + __CM1_CMSIS_VERSION_SUB ) /*!< \deprecated CMSIS HAL version number */ + +#define __CORTEX_M (1U) /*!< Cortex-M Core */ + +/** __FPU_USED indicates whether an FPU is used or not. + This core does not support an FPU at all +*/ +#define __FPU_USED 0U + +#if defined ( __CC_ARM ) +#if defined __TARGET_FPU_VFP +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#if defined __ARM_PCS_VFP +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined ( __GNUC__ ) +#if defined (__VFP_FP__) && !defined(__SOFTFP__) +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined ( __ICCARM__ ) +#if defined __ARMVFP__ +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined ( __TI_ARM__ ) +#if defined __TI_VFP_SUPPORT__ +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined ( __TASKING__ ) +#if defined __FPU_VFP__ +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined ( __CSMC__ ) +#if ( __CSMC__ & 0x400U) +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#endif + +#include "cmsis_compiler.h" /* CMSIS compiler specific defines */ + + +#ifdef __cplusplus +} +#endif + +#endif /* __CORE_CM1_H_GENERIC */ + +#ifndef __CMSIS_GENERIC + +#ifndef __CORE_CM1_H_DEPENDANT +#define __CORE_CM1_H_DEPENDANT + +#ifdef __cplusplus +extern "C" { +#endif + +/* check device defines and use defaults */ +#if defined __CHECK_DEVICE_DEFINES +#ifndef __CM1_REV +#define __CM1_REV 0x0100U +#warning "__CM1_REV not defined in device header file; using default!" +#endif + +#ifndef __NVIC_PRIO_BITS +#define __NVIC_PRIO_BITS 2U +#warning "__NVIC_PRIO_BITS not defined in device header file; using default!" +#endif + +#ifndef __Vendor_SysTickConfig +#define __Vendor_SysTickConfig 0U +#warning "__Vendor_SysTickConfig not defined in device header file; using default!" +#endif +#endif + +/* IO definitions (access restrictions to peripheral registers) */ +/** + \defgroup CMSIS_glob_defs CMSIS Global Defines + + IO Type Qualifiers are used + \li to specify the access to peripheral variables. + \li for automatic generation of peripheral register debug information. +*/ +#ifdef __cplusplus +#define __I volatile /*!< Defines 'read only' permissions */ +#else +#define __I volatile const /*!< Defines 'read only' permissions */ +#endif +#define __O volatile /*!< Defines 'write only' permissions */ +#define __IO volatile /*!< Defines 'read / write' permissions */ + +/* following defines should be used for structure members */ +#define __IM volatile const /*! Defines 'read only' structure member permissions */ +#define __OM volatile /*! Defines 'write only' structure member permissions */ +#define __IOM volatile /*! Defines 'read / write' structure member permissions */ + +/*@} end of group Cortex_M1 */ + + + +/******************************************************************************* + * Register Abstraction + Core Register contain: + - Core Register + - Core NVIC Register + - Core SCB Register + - Core SysTick Register + ******************************************************************************/ +/** + \defgroup CMSIS_core_register Defines and Type Definitions + \brief Type definitions and defines for Cortex-M processor based devices. +*/ + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_CORE Status and Control Registers + \brief Core Register type definitions. + @{ + */ + +/** + \brief Union type to access the Application Program Status Register (APSR). + */ +typedef union +{ + struct + { + uint32_t _reserved0: 28; /*!< bit: 0..27 Reserved */ + uint32_t V: 1; /*!< bit: 28 Overflow condition code flag */ + uint32_t C: 1; /*!< bit: 29 Carry condition code flag */ + uint32_t Z: 1; /*!< bit: 30 Zero condition code flag */ + uint32_t N: 1; /*!< bit: 31 Negative condition code flag */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} APSR_Type; + +/* APSR Register Definitions */ +#define APSR_N_Pos 31U /*!< APSR: N Position */ +#define APSR_N_Msk (1UL << APSR_N_Pos) /*!< APSR: N Mask */ + +#define APSR_Z_Pos 30U /*!< APSR: Z Position */ +#define APSR_Z_Msk (1UL << APSR_Z_Pos) /*!< APSR: Z Mask */ + +#define APSR_C_Pos 29U /*!< APSR: C Position */ +#define APSR_C_Msk (1UL << APSR_C_Pos) /*!< APSR: C Mask */ + +#define APSR_V_Pos 28U /*!< APSR: V Position */ +#define APSR_V_Msk (1UL << APSR_V_Pos) /*!< APSR: V Mask */ + + +/** + \brief Union type to access the Interrupt Program Status Register (IPSR). + */ +typedef union +{ + struct + { + uint32_t ISR: 9; /*!< bit: 0.. 8 Exception number */ + uint32_t _reserved0: 23; /*!< bit: 9..31 Reserved */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} IPSR_Type; + +/* IPSR Register Definitions */ +#define IPSR_ISR_Pos 0U /*!< IPSR: ISR Position */ +#define IPSR_ISR_Msk (0x1FFUL /*<< IPSR_ISR_Pos*/) /*!< IPSR: ISR Mask */ + + +/** + \brief Union type to access the Special-Purpose Program Status Registers (xPSR). + */ +typedef union +{ + struct + { + uint32_t ISR: 9; /*!< bit: 0.. 8 Exception number */ + uint32_t _reserved0: 15; /*!< bit: 9..23 Reserved */ + uint32_t T: 1; /*!< bit: 24 Thumb bit (read 0) */ + uint32_t _reserved1: 3; /*!< bit: 25..27 Reserved */ + uint32_t V: 1; /*!< bit: 28 Overflow condition code flag */ + uint32_t C: 1; /*!< bit: 29 Carry condition code flag */ + uint32_t Z: 1; /*!< bit: 30 Zero condition code flag */ + uint32_t N: 1; /*!< bit: 31 Negative condition code flag */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} xPSR_Type; + +/* xPSR Register Definitions */ +#define xPSR_N_Pos 31U /*!< xPSR: N Position */ +#define xPSR_N_Msk (1UL << xPSR_N_Pos) /*!< xPSR: N Mask */ + +#define xPSR_Z_Pos 30U /*!< xPSR: Z Position */ +#define xPSR_Z_Msk (1UL << xPSR_Z_Pos) /*!< xPSR: Z Mask */ + +#define xPSR_C_Pos 29U /*!< xPSR: C Position */ +#define xPSR_C_Msk (1UL << xPSR_C_Pos) /*!< xPSR: C Mask */ + +#define xPSR_V_Pos 28U /*!< xPSR: V Position */ +#define xPSR_V_Msk (1UL << xPSR_V_Pos) /*!< xPSR: V Mask */ + +#define xPSR_T_Pos 24U /*!< xPSR: T Position */ +#define xPSR_T_Msk (1UL << xPSR_T_Pos) /*!< xPSR: T Mask */ + +#define xPSR_ISR_Pos 0U /*!< xPSR: ISR Position */ +#define xPSR_ISR_Msk (0x1FFUL /*<< xPSR_ISR_Pos*/) /*!< xPSR: ISR Mask */ + + +/** + \brief Union type to access the Control Registers (CONTROL). + */ +typedef union +{ + struct + { + uint32_t _reserved0: 1; /*!< bit: 0 Reserved */ + uint32_t SPSEL: 1; /*!< bit: 1 Stack to be used */ + uint32_t _reserved1: 30; /*!< bit: 2..31 Reserved */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} CONTROL_Type; + +/* CONTROL Register Definitions */ +#define CONTROL_SPSEL_Pos 1U /*!< CONTROL: SPSEL Position */ +#define CONTROL_SPSEL_Msk (1UL << CONTROL_SPSEL_Pos) /*!< CONTROL: SPSEL Mask */ + +/*@} end of group CMSIS_CORE */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_NVIC Nested Vectored Interrupt Controller (NVIC) + \brief Type definitions for the NVIC Registers + @{ + */ + +/** + \brief Structure type to access the Nested Vectored Interrupt Controller (NVIC). + */ +typedef struct +{ + __IOM uint32_t ISER[1U]; /*!< Offset: 0x000 (R/W) Interrupt Set Enable Register */ + uint32_t RESERVED0[31U]; + __IOM uint32_t ICER[1U]; /*!< Offset: 0x080 (R/W) Interrupt Clear Enable Register */ + uint32_t RSERVED1[31U]; + __IOM uint32_t ISPR[1U]; /*!< Offset: 0x100 (R/W) Interrupt Set Pending Register */ + uint32_t RESERVED2[31U]; + __IOM uint32_t ICPR[1U]; /*!< Offset: 0x180 (R/W) Interrupt Clear Pending Register */ + uint32_t RESERVED3[31U]; + uint32_t RESERVED4[64U]; + __IOM uint32_t IP[8U]; /*!< Offset: 0x300 (R/W) Interrupt Priority Register */ +} NVIC_Type; + +/*@} end of group CMSIS_NVIC */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SCB System Control Block (SCB) + \brief Type definitions for the System Control Block Registers + @{ + */ + +/** + \brief Structure type to access the System Control Block (SCB). + */ +typedef struct +{ + __IM uint32_t CPUID; /*!< Offset: 0x000 (R/ ) CPUID Base Register */ + __IOM uint32_t ICSR; /*!< Offset: 0x004 (R/W) Interrupt Control and State Register */ + uint32_t RESERVED0; + __IOM uint32_t AIRCR; /*!< Offset: 0x00C (R/W) Application Interrupt and Reset Control Register */ + __IOM uint32_t SCR; /*!< Offset: 0x010 (R/W) System Control Register */ + __IOM uint32_t CCR; /*!< Offset: 0x014 (R/W) Configuration Control Register */ + uint32_t RESERVED1; + __IOM uint32_t SHP[2U]; /*!< Offset: 0x01C (R/W) System Handlers Priority Registers. [0] is RESERVED */ + __IOM uint32_t SHCSR; /*!< Offset: 0x024 (R/W) System Handler Control and State Register */ +} SCB_Type; + +/* SCB CPUID Register Definitions */ +#define SCB_CPUID_IMPLEMENTER_Pos 24U /*!< SCB CPUID: IMPLEMENTER Position */ +#define SCB_CPUID_IMPLEMENTER_Msk (0xFFUL << SCB_CPUID_IMPLEMENTER_Pos) /*!< SCB CPUID: IMPLEMENTER Mask */ + +#define SCB_CPUID_VARIANT_Pos 20U /*!< SCB CPUID: VARIANT Position */ +#define SCB_CPUID_VARIANT_Msk (0xFUL << SCB_CPUID_VARIANT_Pos) /*!< SCB CPUID: VARIANT Mask */ + +#define SCB_CPUID_ARCHITECTURE_Pos 16U /*!< SCB CPUID: ARCHITECTURE Position */ +#define SCB_CPUID_ARCHITECTURE_Msk (0xFUL << SCB_CPUID_ARCHITECTURE_Pos) /*!< SCB CPUID: ARCHITECTURE Mask */ + +#define SCB_CPUID_PARTNO_Pos 4U /*!< SCB CPUID: PARTNO Position */ +#define SCB_CPUID_PARTNO_Msk (0xFFFUL << SCB_CPUID_PARTNO_Pos) /*!< SCB CPUID: PARTNO Mask */ + +#define SCB_CPUID_REVISION_Pos 0U /*!< SCB CPUID: REVISION Position */ +#define SCB_CPUID_REVISION_Msk (0xFUL /*<< SCB_CPUID_REVISION_Pos*/) /*!< SCB CPUID: REVISION Mask */ + +/* SCB Interrupt Control State Register Definitions */ +#define SCB_ICSR_NMIPENDSET_Pos 31U /*!< SCB ICSR: NMIPENDSET Position */ +#define SCB_ICSR_NMIPENDSET_Msk (1UL << SCB_ICSR_NMIPENDSET_Pos) /*!< SCB ICSR: NMIPENDSET Mask */ + +#define SCB_ICSR_PENDSVSET_Pos 28U /*!< SCB ICSR: PENDSVSET Position */ +#define SCB_ICSR_PENDSVSET_Msk (1UL << SCB_ICSR_PENDSVSET_Pos) /*!< SCB ICSR: PENDSVSET Mask */ + +#define SCB_ICSR_PENDSVCLR_Pos 27U /*!< SCB ICSR: PENDSVCLR Position */ +#define SCB_ICSR_PENDSVCLR_Msk (1UL << SCB_ICSR_PENDSVCLR_Pos) /*!< SCB ICSR: PENDSVCLR Mask */ + +#define SCB_ICSR_PENDSTSET_Pos 26U /*!< SCB ICSR: PENDSTSET Position */ +#define SCB_ICSR_PENDSTSET_Msk (1UL << SCB_ICSR_PENDSTSET_Pos) /*!< SCB ICSR: PENDSTSET Mask */ + +#define SCB_ICSR_PENDSTCLR_Pos 25U /*!< SCB ICSR: PENDSTCLR Position */ +#define SCB_ICSR_PENDSTCLR_Msk (1UL << SCB_ICSR_PENDSTCLR_Pos) /*!< SCB ICSR: PENDSTCLR Mask */ + +#define SCB_ICSR_ISRPREEMPT_Pos 23U /*!< SCB ICSR: ISRPREEMPT Position */ +#define SCB_ICSR_ISRPREEMPT_Msk (1UL << SCB_ICSR_ISRPREEMPT_Pos) /*!< SCB ICSR: ISRPREEMPT Mask */ + +#define SCB_ICSR_ISRPENDING_Pos 22U /*!< SCB ICSR: ISRPENDING Position */ +#define SCB_ICSR_ISRPENDING_Msk (1UL << SCB_ICSR_ISRPENDING_Pos) /*!< SCB ICSR: ISRPENDING Mask */ + +#define SCB_ICSR_VECTPENDING_Pos 12U /*!< SCB ICSR: VECTPENDING Position */ +#define SCB_ICSR_VECTPENDING_Msk (0x1FFUL << SCB_ICSR_VECTPENDING_Pos) /*!< SCB ICSR: VECTPENDING Mask */ + +#define SCB_ICSR_VECTACTIVE_Pos 0U /*!< SCB ICSR: VECTACTIVE Position */ +#define SCB_ICSR_VECTACTIVE_Msk (0x1FFUL /*<< SCB_ICSR_VECTACTIVE_Pos*/) /*!< SCB ICSR: VECTACTIVE Mask */ + +/* SCB Application Interrupt and Reset Control Register Definitions */ +#define SCB_AIRCR_VECTKEY_Pos 16U /*!< SCB AIRCR: VECTKEY Position */ +#define SCB_AIRCR_VECTKEY_Msk (0xFFFFUL << SCB_AIRCR_VECTKEY_Pos) /*!< SCB AIRCR: VECTKEY Mask */ + +#define SCB_AIRCR_VECTKEYSTAT_Pos 16U /*!< SCB AIRCR: VECTKEYSTAT Position */ +#define SCB_AIRCR_VECTKEYSTAT_Msk (0xFFFFUL << SCB_AIRCR_VECTKEYSTAT_Pos) /*!< SCB AIRCR: VECTKEYSTAT Mask */ + +#define SCB_AIRCR_ENDIANESS_Pos 15U /*!< SCB AIRCR: ENDIANESS Position */ +#define SCB_AIRCR_ENDIANESS_Msk (1UL << SCB_AIRCR_ENDIANESS_Pos) /*!< SCB AIRCR: ENDIANESS Mask */ + +#define SCB_AIRCR_SYSRESETREQ_Pos 2U /*!< SCB AIRCR: SYSRESETREQ Position */ +#define SCB_AIRCR_SYSRESETREQ_Msk (1UL << SCB_AIRCR_SYSRESETREQ_Pos) /*!< SCB AIRCR: SYSRESETREQ Mask */ + +#define SCB_AIRCR_VECTCLRACTIVE_Pos 1U /*!< SCB AIRCR: VECTCLRACTIVE Position */ +#define SCB_AIRCR_VECTCLRACTIVE_Msk (1UL << SCB_AIRCR_VECTCLRACTIVE_Pos) /*!< SCB AIRCR: VECTCLRACTIVE Mask */ + +/* SCB System Control Register Definitions */ +#define SCB_SCR_SEVONPEND_Pos 4U /*!< SCB SCR: SEVONPEND Position */ +#define SCB_SCR_SEVONPEND_Msk (1UL << SCB_SCR_SEVONPEND_Pos) /*!< SCB SCR: SEVONPEND Mask */ + +#define SCB_SCR_SLEEPDEEP_Pos 2U /*!< SCB SCR: SLEEPDEEP Position */ +#define SCB_SCR_SLEEPDEEP_Msk (1UL << SCB_SCR_SLEEPDEEP_Pos) /*!< SCB SCR: SLEEPDEEP Mask */ + +#define SCB_SCR_SLEEPONEXIT_Pos 1U /*!< SCB SCR: SLEEPONEXIT Position */ +#define SCB_SCR_SLEEPONEXIT_Msk (1UL << SCB_SCR_SLEEPONEXIT_Pos) /*!< SCB SCR: SLEEPONEXIT Mask */ + +/* SCB Configuration Control Register Definitions */ +#define SCB_CCR_STKALIGN_Pos 9U /*!< SCB CCR: STKALIGN Position */ +#define SCB_CCR_STKALIGN_Msk (1UL << SCB_CCR_STKALIGN_Pos) /*!< SCB CCR: STKALIGN Mask */ + +#define SCB_CCR_UNALIGN_TRP_Pos 3U /*!< SCB CCR: UNALIGN_TRP Position */ +#define SCB_CCR_UNALIGN_TRP_Msk (1UL << SCB_CCR_UNALIGN_TRP_Pos) /*!< SCB CCR: UNALIGN_TRP Mask */ + +/* SCB System Handler Control and State Register Definitions */ +#define SCB_SHCSR_SVCALLPENDED_Pos 15U /*!< SCB SHCSR: SVCALLPENDED Position */ +#define SCB_SHCSR_SVCALLPENDED_Msk (1UL << SCB_SHCSR_SVCALLPENDED_Pos) /*!< SCB SHCSR: SVCALLPENDED Mask */ + +/*@} end of group CMSIS_SCB */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SCnSCB System Controls not in SCB (SCnSCB) + \brief Type definitions for the System Control and ID Register not in the SCB + @{ + */ + +/** + \brief Structure type to access the System Control and ID Register not in the SCB. + */ +typedef struct +{ + uint32_t RESERVED0[2U]; + __IOM uint32_t ACTLR; /*!< Offset: 0x008 (R/W) Auxiliary Control Register */ +} SCnSCB_Type; + +/* Auxiliary Control Register Definitions */ +#define SCnSCB_ACTLR_ITCMUAEN_Pos 4U /*!< ACTLR: Instruction TCM Upper Alias Enable Position */ +#define SCnSCB_ACTLR_ITCMUAEN_Msk (1UL << SCnSCB_ACTLR_ITCMUAEN_Pos) /*!< ACTLR: Instruction TCM Upper Alias Enable Mask */ + +#define SCnSCB_ACTLR_ITCMLAEN_Pos 3U /*!< ACTLR: Instruction TCM Lower Alias Enable Position */ +#define SCnSCB_ACTLR_ITCMLAEN_Msk (1UL << SCnSCB_ACTLR_ITCMLAEN_Pos) /*!< ACTLR: Instruction TCM Lower Alias Enable Mask */ + +/*@} end of group CMSIS_SCnotSCB */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SysTick System Tick Timer (SysTick) + \brief Type definitions for the System Timer Registers. + @{ + */ + +/** + \brief Structure type to access the System Timer (SysTick). + */ +typedef struct +{ + __IOM uint32_t CTRL; /*!< Offset: 0x000 (R/W) SysTick Control and Status Register */ + __IOM uint32_t LOAD; /*!< Offset: 0x004 (R/W) SysTick Reload Value Register */ + __IOM uint32_t VAL; /*!< Offset: 0x008 (R/W) SysTick Current Value Register */ + __IM uint32_t CALIB; /*!< Offset: 0x00C (R/ ) SysTick Calibration Register */ +} SysTick_Type; + +/* SysTick Control / Status Register Definitions */ +#define SysTick_CTRL_COUNTFLAG_Pos 16U /*!< SysTick CTRL: COUNTFLAG Position */ +#define SysTick_CTRL_COUNTFLAG_Msk (1UL << SysTick_CTRL_COUNTFLAG_Pos) /*!< SysTick CTRL: COUNTFLAG Mask */ + +#define SysTick_CTRL_CLKSOURCE_Pos 2U /*!< SysTick CTRL: CLKSOURCE Position */ +#define SysTick_CTRL_CLKSOURCE_Msk (1UL << SysTick_CTRL_CLKSOURCE_Pos) /*!< SysTick CTRL: CLKSOURCE Mask */ + +#define SysTick_CTRL_TICKINT_Pos 1U /*!< SysTick CTRL: TICKINT Position */ +#define SysTick_CTRL_TICKINT_Msk (1UL << SysTick_CTRL_TICKINT_Pos) /*!< SysTick CTRL: TICKINT Mask */ + +#define SysTick_CTRL_ENABLE_Pos 0U /*!< SysTick CTRL: ENABLE Position */ +#define SysTick_CTRL_ENABLE_Msk (1UL /*<< SysTick_CTRL_ENABLE_Pos*/) /*!< SysTick CTRL: ENABLE Mask */ + +/* SysTick Reload Register Definitions */ +#define SysTick_LOAD_RELOAD_Pos 0U /*!< SysTick LOAD: RELOAD Position */ +#define SysTick_LOAD_RELOAD_Msk (0xFFFFFFUL /*<< SysTick_LOAD_RELOAD_Pos*/) /*!< SysTick LOAD: RELOAD Mask */ + +/* SysTick Current Register Definitions */ +#define SysTick_VAL_CURRENT_Pos 0U /*!< SysTick VAL: CURRENT Position */ +#define SysTick_VAL_CURRENT_Msk (0xFFFFFFUL /*<< SysTick_VAL_CURRENT_Pos*/) /*!< SysTick VAL: CURRENT Mask */ + +/* SysTick Calibration Register Definitions */ +#define SysTick_CALIB_NOREF_Pos 31U /*!< SysTick CALIB: NOREF Position */ +#define SysTick_CALIB_NOREF_Msk (1UL << SysTick_CALIB_NOREF_Pos) /*!< SysTick CALIB: NOREF Mask */ + +#define SysTick_CALIB_SKEW_Pos 30U /*!< SysTick CALIB: SKEW Position */ +#define SysTick_CALIB_SKEW_Msk (1UL << SysTick_CALIB_SKEW_Pos) /*!< SysTick CALIB: SKEW Mask */ + +#define SysTick_CALIB_TENMS_Pos 0U /*!< SysTick CALIB: TENMS Position */ +#define SysTick_CALIB_TENMS_Msk (0xFFFFFFUL /*<< SysTick_CALIB_TENMS_Pos*/) /*!< SysTick CALIB: TENMS Mask */ + +/*@} end of group CMSIS_SysTick */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_CoreDebug Core Debug Registers (CoreDebug) + \brief Cortex-M1 Core Debug Registers (DCB registers, SHCSR, and DFSR) are only accessible over DAP and not via processor. + Therefore they are not covered by the Cortex-M1 header file. + @{ + */ +/*@} end of group CMSIS_CoreDebug */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_core_bitfield Core register bit field macros + \brief Macros for use with bit field definitions (xxx_Pos, xxx_Msk). + @{ + */ + +/** + \brief Mask and shift a bit field value for use in a register bit range. + \param[in] field Name of the register bit field. + \param[in] value Value of the bit field. This parameter is interpreted as an uint32_t type. + \return Masked and shifted value. +*/ +#define _VAL2FLD(field, value) (((uint32_t)(value) << field ## _Pos) & field ## _Msk) + +/** + \brief Mask and shift a register value to extract a bit filed value. + \param[in] field Name of the register bit field. + \param[in] value Value of register. This parameter is interpreted as an uint32_t type. + \return Masked and shifted bit field value. +*/ +#define _FLD2VAL(field, value) (((uint32_t)(value) & field ## _Msk) >> field ## _Pos) + +/*@} end of group CMSIS_core_bitfield */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_core_base Core Definitions + \brief Definitions for base addresses, unions, and structures. + @{ + */ + +/* Memory mapping of Core Hardware */ +#define SCS_BASE (0xE000E000UL) /*!< System Control Space Base Address */ +#define SysTick_BASE (SCS_BASE + 0x0010UL) /*!< SysTick Base Address */ +#define NVIC_BASE (SCS_BASE + 0x0100UL) /*!< NVIC Base Address */ +#define SCB_BASE (SCS_BASE + 0x0D00UL) /*!< System Control Block Base Address */ + +#define SCnSCB ((SCnSCB_Type *) SCS_BASE ) /*!< System control Register not in SCB */ +#define SCB ((SCB_Type *) SCB_BASE ) /*!< SCB configuration struct */ +#define SysTick ((SysTick_Type *) SysTick_BASE ) /*!< SysTick configuration struct */ +#define NVIC ((NVIC_Type *) NVIC_BASE ) /*!< NVIC configuration struct */ + + +/*@} */ + + + +/******************************************************************************* + * Hardware Abstraction Layer + Core Function Interface contains: + - Core NVIC Functions + - Core SysTick Functions + - Core Register Access Functions + ******************************************************************************/ +/** + \defgroup CMSIS_Core_FunctionInterface Functions and Instructions Reference +*/ + + + +/* ########################## NVIC functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_NVICFunctions NVIC Functions + \brief Functions that manage interrupts and exceptions via the NVIC. + @{ + */ + +#ifdef CMSIS_NVIC_VIRTUAL +#ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE +#define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h" +#endif +#include CMSIS_NVIC_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetPriorityGrouping __NVIC_SetPriorityGrouping +#define NVIC_GetPriorityGrouping __NVIC_GetPriorityGrouping +#define NVIC_EnableIRQ __NVIC_EnableIRQ +#define NVIC_GetEnableIRQ __NVIC_GetEnableIRQ +#define NVIC_DisableIRQ __NVIC_DisableIRQ +#define NVIC_GetPendingIRQ __NVIC_GetPendingIRQ +#define NVIC_SetPendingIRQ __NVIC_SetPendingIRQ +#define NVIC_ClearPendingIRQ __NVIC_ClearPendingIRQ +/*#define NVIC_GetActive __NVIC_GetActive not available for Cortex-M1 */ +#define NVIC_SetPriority __NVIC_SetPriority +#define NVIC_GetPriority __NVIC_GetPriority +#define NVIC_SystemReset __NVIC_SystemReset +#endif /* CMSIS_NVIC_VIRTUAL */ + +#ifdef CMSIS_VECTAB_VIRTUAL +#ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h" +#endif +#include CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetVector __NVIC_SetVector +#define NVIC_GetVector __NVIC_GetVector +#endif /* (CMSIS_VECTAB_VIRTUAL) */ + +#define NVIC_USER_IRQ_OFFSET 16 + + +/* The following EXC_RETURN values are saved the LR on exception entry */ +#define EXC_RETURN_HANDLER (0xFFFFFFF1UL) /* return to Handler mode, uses MSP after return */ +#define EXC_RETURN_THREAD_MSP (0xFFFFFFF9UL) /* return to Thread mode, uses MSP after return */ +#define EXC_RETURN_THREAD_PSP (0xFFFFFFFDUL) /* return to Thread mode, uses PSP after return */ + + +/* Interrupt Priorities are WORD accessible only under Armv6-M */ +/* The following MACROS handle generation of the register offset and byte masks */ +#define _BIT_SHIFT(IRQn) ( ((((uint32_t)(int32_t)(IRQn)) ) & 0x03UL) * 8UL) +#define _SHP_IDX(IRQn) ( (((((uint32_t)(int32_t)(IRQn)) & 0x0FUL)-8UL) >> 2UL) ) +#define _IP_IDX(IRQn) ( (((uint32_t)(int32_t)(IRQn)) >> 2UL) ) + +#define __NVIC_SetPriorityGrouping(X) (void)(X) +#define __NVIC_GetPriorityGrouping() (0U) + +/** + \brief Enable Interrupt + \details Enables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Interrupt Enable status + \details Returns a device specific interrupt enable status from the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISER[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Disable Interrupt + \details Disables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + __DSB(); + __ISB(); + } +} + + +/** + \brief Get Pending Interrupt + \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not pending. + \return 1 Interrupt status is pending. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISPR[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Pending Interrupt + \details Sets the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Clear Pending Interrupt + \details Clears the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Set Interrupt Priority + \details Sets the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \param [in] priority Priority to set. + \note The priority cannot be set for every processor exception. + */ +__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->IP[_IP_IDX(IRQn)] = ((uint32_t)(NVIC->IP[_IP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); + } + else + { + SCB->SHP[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHP[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); + } +} + + +/** + \brief Get Interrupt Priority + \details Reads the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Interrupt Priority. + Value is aligned automatically to the implemented priority bits of the microcontroller. + */ +__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn) +{ + + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->IP[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + } + else + { + return ((uint32_t)(((SCB->SHP[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + } +} + + +/** + \brief Encode Priority + \details Encodes the priority for an interrupt with the given priority group, + preemptive priority value, and subpriority value. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set. + \param [in] PriorityGroup Used priority group. + \param [in] PreemptPriority Preemptive priority value (starting from 0). + \param [in] SubPriority Subpriority value (starting from 0). + \return Encoded priority. Value can be used in the function \ref NVIC_SetPriority(). + */ +__STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority) +{ + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + uint32_t PreemptPriorityBits; + uint32_t SubPriorityBits; + + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); + SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + + return ( + ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) | + ((SubPriority & (uint32_t)((1UL << (SubPriorityBits )) - 1UL))) + ); +} + + +/** + \brief Decode Priority + \details Decodes an interrupt priority value with a given priority group to + preemptive priority value and subpriority value. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set. + \param [in] Priority Priority value, which can be retrieved with the function \ref NVIC_GetPriority(). + \param [in] PriorityGroup Used priority group. + \param [out] pPreemptPriority Preemptive priority value (starting from 0). + \param [out] pSubPriority Subpriority value (starting from 0). + */ +__STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* const pPreemptPriority, uint32_t* const pSubPriority) +{ + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + uint32_t PreemptPriorityBits; + uint32_t SubPriorityBits; + + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); + SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + + *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL); + *pSubPriority = (Priority ) & (uint32_t)((1UL << (SubPriorityBits )) - 1UL); +} + + + +/** + \brief Set Interrupt Vector + \details Sets an interrupt vector in SRAM based interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + Address 0 must be mapped to SRAM. + \param [in] IRQn Interrupt number + \param [in] vector Address of interrupt handler function + */ +__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector) +{ + uint32_t* vectors = (uint32_t*)0x0U; + vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector; +} + + +/** + \brief Get Interrupt Vector + \details Reads an interrupt vector from interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Address of interrupt handler function + */ +__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn) +{ + uint32_t* vectors = (uint32_t*)0x0U; + return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET]; +} + + +/** + \brief System Reset + \details Initiates a system reset request to reset the MCU. + */ +__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void) +{ + __DSB(); /* Ensure all outstanding memory accesses included + buffered write are completed before reset */ + SCB->AIRCR = ((0x5FAUL << SCB_AIRCR_VECTKEY_Pos) | + SCB_AIRCR_SYSRESETREQ_Msk); + __DSB(); /* Ensure completion of memory access */ + + for (;;) /* wait until reset */ + { + __NOP(); + } +} + +/*@} end of CMSIS_Core_NVICFunctions */ + + +/* ########################## FPU functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_FpuFunctions FPU Functions + \brief Function that provides FPU type. + @{ + */ + +/** + \brief get FPU type + \details returns the FPU type + \returns + - \b 0: No FPU + - \b 1: Single precision FPU + - \b 2: Double + Single precision FPU + */ +__STATIC_INLINE uint32_t SCB_GetFPUType(void) +{ + return 0U; /* No FPU */ +} + + +/*@} end of CMSIS_Core_FpuFunctions */ + + + +/* ################################## SysTick function ############################################ */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_SysTickFunctions SysTick Functions + \brief Functions that configure the System. + @{ + */ + +#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U) + +/** + \brief System Tick Configuration + \details Initializes the System Timer and its interrupt, and starts the System Tick Timer. + Counter is in free running mode to generate periodic interrupts. + \param [in] ticks Number of ticks between two interrupts. + \return 0 Function succeeded. + \return 1 Function failed. + \note When the variable __Vendor_SysTickConfig is set to 1, then the + function SysTick_Config is not included. In this case, the file device.h + must contain a vendor-specific implementation of this function. + */ +__STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks) +{ + if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk) + { + return (1UL); /* Reload value impossible */ + } + + SysTick->LOAD = (uint32_t)(ticks - 1UL); /* set reload register */ + NVIC_SetPriority (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */ + SysTick->VAL = 0UL; /* Load the SysTick Counter Value */ + SysTick->CTRL = SysTick_CTRL_CLKSOURCE_Msk | + SysTick_CTRL_TICKINT_Msk | + SysTick_CTRL_ENABLE_Msk; /* Enable SysTick IRQ and SysTick Timer */ + return (0UL); /* Function successful */ +} + +#endif + +/*@} end of CMSIS_Core_SysTickFunctions */ + + + + +#ifdef __cplusplus +} +#endif + +#endif /* __CORE_CM1_H_DEPENDANT */ + +#endif /* __CMSIS_GENERIC */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/core_cm23.h b/EpsilonLights/Drivers/CMSIS/Include/core_cm23.h new file mode 100644 index 00000000..339bf7c0 --- /dev/null +++ b/EpsilonLights/Drivers/CMSIS/Include/core_cm23.h @@ -0,0 +1,1995 @@ +/**************************************************************************//** + * @file core_cm23.h + * @brief CMSIS Cortex-M23 Core Peripheral Access Layer Header File + * @version V5.0.7 + * @date 22. June 2018 + ******************************************************************************/ +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ + +#if defined ( __ICCARM__ ) +#pragma system_include /* treat file as system include file for MISRA check */ +#elif defined (__clang__) +#pragma clang system_header /* treat file as system include file */ +#endif + +#ifndef __CORE_CM23_H_GENERIC +#define __CORE_CM23_H_GENERIC + +#include + +#ifdef __cplusplus +extern "C" { +#endif + +/** + \page CMSIS_MISRA_Exceptions MISRA-C:2004 Compliance Exceptions + CMSIS violates the following MISRA-C:2004 rules: + + \li Required Rule 8.5, object/function definition in header file.
+ Function definitions in header files are used to allow 'inlining'. + + \li Required Rule 18.4, declaration of union type or object of union type: '{...}'.
+ Unions are used for effective representation of core registers. + + \li Advisory Rule 19.7, Function-like macro defined.
+ Function-like macros are used to allow more efficient code. + */ + + +/******************************************************************************* + * CMSIS definitions + ******************************************************************************/ +/** + \ingroup Cortex_M23 + @{ + */ + +#include "cmsis_version.h" + +/* CMSIS definitions */ +#define __CM23_CMSIS_VERSION_MAIN (__CM_CMSIS_VERSION_MAIN) /*!< \deprecated [31:16] CMSIS HAL main version */ +#define __CM23_CMSIS_VERSION_SUB (__CM_CMSIS_VERSION_SUB) /*!< \deprecated [15:0] CMSIS HAL sub version */ +#define __CM23_CMSIS_VERSION ((__CM23_CMSIS_VERSION_MAIN << 16U) | \ + __CM23_CMSIS_VERSION_SUB ) /*!< \deprecated CMSIS HAL version number */ + +#define __CORTEX_M (23U) /*!< Cortex-M Core */ + +/** __FPU_USED indicates whether an FPU is used or not. + This core does not support an FPU at all +*/ +#define __FPU_USED 0U + +#if defined ( __CC_ARM ) +#if defined __TARGET_FPU_VFP +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#if defined __ARM_PCS_VFP +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined ( __GNUC__ ) +#if defined (__VFP_FP__) && !defined(__SOFTFP__) +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined ( __ICCARM__ ) +#if defined __ARMVFP__ +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined ( __TI_ARM__ ) +#if defined __TI_VFP_SUPPORT__ +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined ( __TASKING__ ) +#if defined __FPU_VFP__ +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#elif defined ( __CSMC__ ) +#if ( __CSMC__ & 0x400U) +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#endif + +#endif + +#include "cmsis_compiler.h" /* CMSIS compiler specific defines */ + + +#ifdef __cplusplus +} +#endif + +#endif /* __CORE_CM23_H_GENERIC */ + +#ifndef __CMSIS_GENERIC + +#ifndef __CORE_CM23_H_DEPENDANT +#define __CORE_CM23_H_DEPENDANT + +#ifdef __cplusplus +extern "C" { +#endif + +/* check device defines and use defaults */ +#if defined __CHECK_DEVICE_DEFINES +#ifndef __CM23_REV +#define __CM23_REV 0x0000U +#warning "__CM23_REV not defined in device header file; using default!" +#endif + +#ifndef __FPU_PRESENT +#define __FPU_PRESENT 0U +#warning "__FPU_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __MPU_PRESENT +#define __MPU_PRESENT 0U +#warning "__MPU_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __SAUREGION_PRESENT +#define __SAUREGION_PRESENT 0U +#warning "__SAUREGION_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __VTOR_PRESENT +#define __VTOR_PRESENT 0U +#warning "__VTOR_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __NVIC_PRIO_BITS +#define __NVIC_PRIO_BITS 2U +#warning "__NVIC_PRIO_BITS not defined in device header file; using default!" +#endif + +#ifndef __Vendor_SysTickConfig +#define __Vendor_SysTickConfig 0U +#warning "__Vendor_SysTickConfig not defined in device header file; using default!" +#endif + +#ifndef __ETM_PRESENT +#define __ETM_PRESENT 0U +#warning "__ETM_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __MTB_PRESENT +#define __MTB_PRESENT 0U +#warning "__MTB_PRESENT not defined in device header file; using default!" +#endif + +#endif + +/* IO definitions (access restrictions to peripheral registers) */ +/** + \defgroup CMSIS_glob_defs CMSIS Global Defines + + IO Type Qualifiers are used + \li to specify the access to peripheral variables. + \li for automatic generation of peripheral register debug information. +*/ +#ifdef __cplusplus +#define __I volatile /*!< Defines 'read only' permissions */ +#else +#define __I volatile const /*!< Defines 'read only' permissions */ +#endif +#define __O volatile /*!< Defines 'write only' permissions */ +#define __IO volatile /*!< Defines 'read / write' permissions */ + +/* following defines should be used for structure members */ +#define __IM volatile const /*! Defines 'read only' structure member permissions */ +#define __OM volatile /*! Defines 'write only' structure member permissions */ +#define __IOM volatile /*! Defines 'read / write' structure member permissions */ + +/*@} end of group Cortex_M23 */ + + + +/******************************************************************************* + * Register Abstraction + Core Register contain: + - Core Register + - Core NVIC Register + - Core SCB Register + - Core SysTick Register + - Core Debug Register + - Core MPU Register + - Core SAU Register + ******************************************************************************/ +/** + \defgroup CMSIS_core_register Defines and Type Definitions + \brief Type definitions and defines for Cortex-M processor based devices. +*/ + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_CORE Status and Control Registers + \brief Core Register type definitions. + @{ + */ + +/** + \brief Union type to access the Application Program Status Register (APSR). + */ +typedef union +{ + struct + { + uint32_t _reserved0: 28; /*!< bit: 0..27 Reserved */ + uint32_t V: 1; /*!< bit: 28 Overflow condition code flag */ + uint32_t C: 1; /*!< bit: 29 Carry condition code flag */ + uint32_t Z: 1; /*!< bit: 30 Zero condition code flag */ + uint32_t N: 1; /*!< bit: 31 Negative condition code flag */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} APSR_Type; + +/* APSR Register Definitions */ +#define APSR_N_Pos 31U /*!< APSR: N Position */ +#define APSR_N_Msk (1UL << APSR_N_Pos) /*!< APSR: N Mask */ + +#define APSR_Z_Pos 30U /*!< APSR: Z Position */ +#define APSR_Z_Msk (1UL << APSR_Z_Pos) /*!< APSR: Z Mask */ + +#define APSR_C_Pos 29U /*!< APSR: C Position */ +#define APSR_C_Msk (1UL << APSR_C_Pos) /*!< APSR: C Mask */ + +#define APSR_V_Pos 28U /*!< APSR: V Position */ +#define APSR_V_Msk (1UL << APSR_V_Pos) /*!< APSR: V Mask */ + + +/** + \brief Union type to access the Interrupt Program Status Register (IPSR). + */ +typedef union +{ + struct + { + uint32_t ISR: 9; /*!< bit: 0.. 8 Exception number */ + uint32_t _reserved0: 23; /*!< bit: 9..31 Reserved */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} IPSR_Type; + +/* IPSR Register Definitions */ +#define IPSR_ISR_Pos 0U /*!< IPSR: ISR Position */ +#define IPSR_ISR_Msk (0x1FFUL /*<< IPSR_ISR_Pos*/) /*!< IPSR: ISR Mask */ + + +/** + \brief Union type to access the Special-Purpose Program Status Registers (xPSR). + */ +typedef union +{ + struct + { + uint32_t ISR: 9; /*!< bit: 0.. 8 Exception number */ + uint32_t _reserved0: 15; /*!< bit: 9..23 Reserved */ + uint32_t T: 1; /*!< bit: 24 Thumb bit (read 0) */ + uint32_t _reserved1: 3; /*!< bit: 25..27 Reserved */ + uint32_t V: 1; /*!< bit: 28 Overflow condition code flag */ + uint32_t C: 1; /*!< bit: 29 Carry condition code flag */ + uint32_t Z: 1; /*!< bit: 30 Zero condition code flag */ + uint32_t N: 1; /*!< bit: 31 Negative condition code flag */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} xPSR_Type; + +/* xPSR Register Definitions */ +#define xPSR_N_Pos 31U /*!< xPSR: N Position */ +#define xPSR_N_Msk (1UL << xPSR_N_Pos) /*!< xPSR: N Mask */ + +#define xPSR_Z_Pos 30U /*!< xPSR: Z Position */ +#define xPSR_Z_Msk (1UL << xPSR_Z_Pos) /*!< xPSR: Z Mask */ + +#define xPSR_C_Pos 29U /*!< xPSR: C Position */ +#define xPSR_C_Msk (1UL << xPSR_C_Pos) /*!< xPSR: C Mask */ + +#define xPSR_V_Pos 28U /*!< xPSR: V Position */ +#define xPSR_V_Msk (1UL << xPSR_V_Pos) /*!< xPSR: V Mask */ + +#define xPSR_T_Pos 24U /*!< xPSR: T Position */ +#define xPSR_T_Msk (1UL << xPSR_T_Pos) /*!< xPSR: T Mask */ + +#define xPSR_ISR_Pos 0U /*!< xPSR: ISR Position */ +#define xPSR_ISR_Msk (0x1FFUL /*<< xPSR_ISR_Pos*/) /*!< xPSR: ISR Mask */ + + +/** + \brief Union type to access the Control Registers (CONTROL). + */ +typedef union +{ + struct + { + uint32_t nPRIV: 1; /*!< bit: 0 Execution privilege in Thread mode */ + uint32_t SPSEL: 1; /*!< bit: 1 Stack-pointer select */ + uint32_t _reserved1: 30; /*!< bit: 2..31 Reserved */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} CONTROL_Type; + +/* CONTROL Register Definitions */ +#define CONTROL_SPSEL_Pos 1U /*!< CONTROL: SPSEL Position */ +#define CONTROL_SPSEL_Msk (1UL << CONTROL_SPSEL_Pos) /*!< CONTROL: SPSEL Mask */ + +#define CONTROL_nPRIV_Pos 0U /*!< CONTROL: nPRIV Position */ +#define CONTROL_nPRIV_Msk (1UL /*<< CONTROL_nPRIV_Pos*/) /*!< CONTROL: nPRIV Mask */ + +/*@} end of group CMSIS_CORE */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_NVIC Nested Vectored Interrupt Controller (NVIC) + \brief Type definitions for the NVIC Registers + @{ + */ + +/** + \brief Structure type to access the Nested Vectored Interrupt Controller (NVIC). + */ +typedef struct +{ + __IOM uint32_t ISER[16U]; /*!< Offset: 0x000 (R/W) Interrupt Set Enable Register */ + uint32_t RESERVED0[16U]; + __IOM uint32_t ICER[16U]; /*!< Offset: 0x080 (R/W) Interrupt Clear Enable Register */ + uint32_t RSERVED1[16U]; + __IOM uint32_t ISPR[16U]; /*!< Offset: 0x100 (R/W) Interrupt Set Pending Register */ + uint32_t RESERVED2[16U]; + __IOM uint32_t ICPR[16U]; /*!< Offset: 0x180 (R/W) Interrupt Clear Pending Register */ + uint32_t RESERVED3[16U]; + __IOM uint32_t IABR[16U]; /*!< Offset: 0x200 (R/W) Interrupt Active bit Register */ + uint32_t RESERVED4[16U]; + __IOM uint32_t ITNS[16U]; /*!< Offset: 0x280 (R/W) Interrupt Non-Secure State Register */ + uint32_t RESERVED5[16U]; + __IOM uint32_t IPR[124U]; /*!< Offset: 0x300 (R/W) Interrupt Priority Register */ +} NVIC_Type; + +/*@} end of group CMSIS_NVIC */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SCB System Control Block (SCB) + \brief Type definitions for the System Control Block Registers + @{ + */ + +/** + \brief Structure type to access the System Control Block (SCB). + */ +typedef struct +{ + __IM uint32_t CPUID; /*!< Offset: 0x000 (R/ ) CPUID Base Register */ + __IOM uint32_t ICSR; /*!< Offset: 0x004 (R/W) Interrupt Control and State Register */ +#if defined (__VTOR_PRESENT) && (__VTOR_PRESENT == 1U) + __IOM uint32_t VTOR; /*!< Offset: 0x008 (R/W) Vector Table Offset Register */ +#else + uint32_t RESERVED0; +#endif + __IOM uint32_t AIRCR; /*!< Offset: 0x00C (R/W) Application Interrupt and Reset Control Register */ + __IOM uint32_t SCR; /*!< Offset: 0x010 (R/W) System Control Register */ + __IOM uint32_t CCR; /*!< Offset: 0x014 (R/W) Configuration Control Register */ + uint32_t RESERVED1; + __IOM uint32_t SHPR[2U]; /*!< Offset: 0x01C (R/W) System Handlers Priority Registers. [0] is RESERVED */ + __IOM uint32_t SHCSR; /*!< Offset: 0x024 (R/W) System Handler Control and State Register */ +} SCB_Type; + +/* SCB CPUID Register Definitions */ +#define SCB_CPUID_IMPLEMENTER_Pos 24U /*!< SCB CPUID: IMPLEMENTER Position */ +#define SCB_CPUID_IMPLEMENTER_Msk (0xFFUL << SCB_CPUID_IMPLEMENTER_Pos) /*!< SCB CPUID: IMPLEMENTER Mask */ + +#define SCB_CPUID_VARIANT_Pos 20U /*!< SCB CPUID: VARIANT Position */ +#define SCB_CPUID_VARIANT_Msk (0xFUL << SCB_CPUID_VARIANT_Pos) /*!< SCB CPUID: VARIANT Mask */ + +#define SCB_CPUID_ARCHITECTURE_Pos 16U /*!< SCB CPUID: ARCHITECTURE Position */ +#define SCB_CPUID_ARCHITECTURE_Msk (0xFUL << SCB_CPUID_ARCHITECTURE_Pos) /*!< SCB CPUID: ARCHITECTURE Mask */ + +#define SCB_CPUID_PARTNO_Pos 4U /*!< SCB CPUID: PARTNO Position */ +#define SCB_CPUID_PARTNO_Msk (0xFFFUL << SCB_CPUID_PARTNO_Pos) /*!< SCB CPUID: PARTNO Mask */ + +#define SCB_CPUID_REVISION_Pos 0U /*!< SCB CPUID: REVISION Position */ +#define SCB_CPUID_REVISION_Msk (0xFUL /*<< SCB_CPUID_REVISION_Pos*/) /*!< SCB CPUID: REVISION Mask */ + +/* SCB Interrupt Control State Register Definitions */ +#define SCB_ICSR_PENDNMISET_Pos 31U /*!< SCB ICSR: PENDNMISET Position */ +#define SCB_ICSR_PENDNMISET_Msk (1UL << SCB_ICSR_PENDNMISET_Pos) /*!< SCB ICSR: PENDNMISET Mask */ + +#define SCB_ICSR_NMIPENDSET_Pos SCB_ICSR_PENDNMISET_Pos /*!< SCB ICSR: NMIPENDSET Position, backward compatibility */ +#define SCB_ICSR_NMIPENDSET_Msk SCB_ICSR_PENDNMISET_Msk /*!< SCB ICSR: NMIPENDSET Mask, backward compatibility */ + +#define SCB_ICSR_PENDNMICLR_Pos 30U /*!< SCB ICSR: PENDNMICLR Position */ +#define SCB_ICSR_PENDNMICLR_Msk (1UL << SCB_ICSR_PENDNMICLR_Pos) /*!< SCB ICSR: PENDNMICLR Mask */ + +#define SCB_ICSR_PENDSVSET_Pos 28U /*!< SCB ICSR: PENDSVSET Position */ +#define SCB_ICSR_PENDSVSET_Msk (1UL << SCB_ICSR_PENDSVSET_Pos) /*!< SCB ICSR: PENDSVSET Mask */ + +#define SCB_ICSR_PENDSVCLR_Pos 27U /*!< SCB ICSR: PENDSVCLR Position */ +#define SCB_ICSR_PENDSVCLR_Msk (1UL << SCB_ICSR_PENDSVCLR_Pos) /*!< SCB ICSR: PENDSVCLR Mask */ + +#define SCB_ICSR_PENDSTSET_Pos 26U /*!< SCB ICSR: PENDSTSET Position */ +#define SCB_ICSR_PENDSTSET_Msk (1UL << SCB_ICSR_PENDSTSET_Pos) /*!< SCB ICSR: PENDSTSET Mask */ + +#define SCB_ICSR_PENDSTCLR_Pos 25U /*!< SCB ICSR: PENDSTCLR Position */ +#define SCB_ICSR_PENDSTCLR_Msk (1UL << SCB_ICSR_PENDSTCLR_Pos) /*!< SCB ICSR: PENDSTCLR Mask */ + +#define SCB_ICSR_STTNS_Pos 24U /*!< SCB ICSR: STTNS Position (Security Extension) */ +#define SCB_ICSR_STTNS_Msk (1UL << SCB_ICSR_STTNS_Pos) /*!< SCB ICSR: STTNS Mask (Security Extension) */ + +#define SCB_ICSR_ISRPREEMPT_Pos 23U /*!< SCB ICSR: ISRPREEMPT Position */ +#define SCB_ICSR_ISRPREEMPT_Msk (1UL << SCB_ICSR_ISRPREEMPT_Pos) /*!< SCB ICSR: ISRPREEMPT Mask */ + +#define SCB_ICSR_ISRPENDING_Pos 22U /*!< SCB ICSR: ISRPENDING Position */ +#define SCB_ICSR_ISRPENDING_Msk (1UL << SCB_ICSR_ISRPENDING_Pos) /*!< SCB ICSR: ISRPENDING Mask */ + +#define SCB_ICSR_VECTPENDING_Pos 12U /*!< SCB ICSR: VECTPENDING Position */ +#define SCB_ICSR_VECTPENDING_Msk (0x1FFUL << SCB_ICSR_VECTPENDING_Pos) /*!< SCB ICSR: VECTPENDING Mask */ + +#define SCB_ICSR_RETTOBASE_Pos 11U /*!< SCB ICSR: RETTOBASE Position */ +#define SCB_ICSR_RETTOBASE_Msk (1UL << SCB_ICSR_RETTOBASE_Pos) /*!< SCB ICSR: RETTOBASE Mask */ + +#define SCB_ICSR_VECTACTIVE_Pos 0U /*!< SCB ICSR: VECTACTIVE Position */ +#define SCB_ICSR_VECTACTIVE_Msk (0x1FFUL /*<< SCB_ICSR_VECTACTIVE_Pos*/) /*!< SCB ICSR: VECTACTIVE Mask */ + +#if defined (__VTOR_PRESENT) && (__VTOR_PRESENT == 1U) +/* SCB Vector Table Offset Register Definitions */ +#define SCB_VTOR_TBLOFF_Pos 7U /*!< SCB VTOR: TBLOFF Position */ +#define SCB_VTOR_TBLOFF_Msk (0x1FFFFFFUL << SCB_VTOR_TBLOFF_Pos) /*!< SCB VTOR: TBLOFF Mask */ +#endif + +/* SCB Application Interrupt and Reset Control Register Definitions */ +#define SCB_AIRCR_VECTKEY_Pos 16U /*!< SCB AIRCR: VECTKEY Position */ +#define SCB_AIRCR_VECTKEY_Msk (0xFFFFUL << SCB_AIRCR_VECTKEY_Pos) /*!< SCB AIRCR: VECTKEY Mask */ + +#define SCB_AIRCR_VECTKEYSTAT_Pos 16U /*!< SCB AIRCR: VECTKEYSTAT Position */ +#define SCB_AIRCR_VECTKEYSTAT_Msk (0xFFFFUL << SCB_AIRCR_VECTKEYSTAT_Pos) /*!< SCB AIRCR: VECTKEYSTAT Mask */ + +#define SCB_AIRCR_ENDIANESS_Pos 15U /*!< SCB AIRCR: ENDIANESS Position */ +#define SCB_AIRCR_ENDIANESS_Msk (1UL << SCB_AIRCR_ENDIANESS_Pos) /*!< SCB AIRCR: ENDIANESS Mask */ + +#define SCB_AIRCR_PRIS_Pos 14U /*!< SCB AIRCR: PRIS Position */ +#define SCB_AIRCR_PRIS_Msk (1UL << SCB_AIRCR_PRIS_Pos) /*!< SCB AIRCR: PRIS Mask */ + +#define SCB_AIRCR_BFHFNMINS_Pos 13U /*!< SCB AIRCR: BFHFNMINS Position */ +#define SCB_AIRCR_BFHFNMINS_Msk (1UL << SCB_AIRCR_BFHFNMINS_Pos) /*!< SCB AIRCR: BFHFNMINS Mask */ + +#define SCB_AIRCR_SYSRESETREQS_Pos 3U /*!< SCB AIRCR: SYSRESETREQS Position */ +#define SCB_AIRCR_SYSRESETREQS_Msk (1UL << SCB_AIRCR_SYSRESETREQS_Pos) /*!< SCB AIRCR: SYSRESETREQS Mask */ + +#define SCB_AIRCR_SYSRESETREQ_Pos 2U /*!< SCB AIRCR: SYSRESETREQ Position */ +#define SCB_AIRCR_SYSRESETREQ_Msk (1UL << SCB_AIRCR_SYSRESETREQ_Pos) /*!< SCB AIRCR: SYSRESETREQ Mask */ + +#define SCB_AIRCR_VECTCLRACTIVE_Pos 1U /*!< SCB AIRCR: VECTCLRACTIVE Position */ +#define SCB_AIRCR_VECTCLRACTIVE_Msk (1UL << SCB_AIRCR_VECTCLRACTIVE_Pos) /*!< SCB AIRCR: VECTCLRACTIVE Mask */ + +/* SCB System Control Register Definitions */ +#define SCB_SCR_SEVONPEND_Pos 4U /*!< SCB SCR: SEVONPEND Position */ +#define SCB_SCR_SEVONPEND_Msk (1UL << SCB_SCR_SEVONPEND_Pos) /*!< SCB SCR: SEVONPEND Mask */ + +#define SCB_SCR_SLEEPDEEPS_Pos 3U /*!< SCB SCR: SLEEPDEEPS Position */ +#define SCB_SCR_SLEEPDEEPS_Msk (1UL << SCB_SCR_SLEEPDEEPS_Pos) /*!< SCB SCR: SLEEPDEEPS Mask */ + +#define SCB_SCR_SLEEPDEEP_Pos 2U /*!< SCB SCR: SLEEPDEEP Position */ +#define SCB_SCR_SLEEPDEEP_Msk (1UL << SCB_SCR_SLEEPDEEP_Pos) /*!< SCB SCR: SLEEPDEEP Mask */ + +#define SCB_SCR_SLEEPONEXIT_Pos 1U /*!< SCB SCR: SLEEPONEXIT Position */ +#define SCB_SCR_SLEEPONEXIT_Msk (1UL << SCB_SCR_SLEEPONEXIT_Pos) /*!< SCB SCR: SLEEPONEXIT Mask */ + +/* SCB Configuration Control Register Definitions */ +#define SCB_CCR_BP_Pos 18U /*!< SCB CCR: BP Position */ +#define SCB_CCR_BP_Msk (1UL << SCB_CCR_BP_Pos) /*!< SCB CCR: BP Mask */ + +#define SCB_CCR_IC_Pos 17U /*!< SCB CCR: IC Position */ +#define SCB_CCR_IC_Msk (1UL << SCB_CCR_IC_Pos) /*!< SCB CCR: IC Mask */ + +#define SCB_CCR_DC_Pos 16U /*!< SCB CCR: DC Position */ +#define SCB_CCR_DC_Msk (1UL << SCB_CCR_DC_Pos) /*!< SCB CCR: DC Mask */ + +#define SCB_CCR_STKOFHFNMIGN_Pos 10U /*!< SCB CCR: STKOFHFNMIGN Position */ +#define SCB_CCR_STKOFHFNMIGN_Msk (1UL << SCB_CCR_STKOFHFNMIGN_Pos) /*!< SCB CCR: STKOFHFNMIGN Mask */ + +#define SCB_CCR_BFHFNMIGN_Pos 8U /*!< SCB CCR: BFHFNMIGN Position */ +#define SCB_CCR_BFHFNMIGN_Msk (1UL << SCB_CCR_BFHFNMIGN_Pos) /*!< SCB CCR: BFHFNMIGN Mask */ + +#define SCB_CCR_DIV_0_TRP_Pos 4U /*!< SCB CCR: DIV_0_TRP Position */ +#define SCB_CCR_DIV_0_TRP_Msk (1UL << SCB_CCR_DIV_0_TRP_Pos) /*!< SCB CCR: DIV_0_TRP Mask */ + +#define SCB_CCR_UNALIGN_TRP_Pos 3U /*!< SCB CCR: UNALIGN_TRP Position */ +#define SCB_CCR_UNALIGN_TRP_Msk (1UL << SCB_CCR_UNALIGN_TRP_Pos) /*!< SCB CCR: UNALIGN_TRP Mask */ + +#define SCB_CCR_USERSETMPEND_Pos 1U /*!< SCB CCR: USERSETMPEND Position */ +#define SCB_CCR_USERSETMPEND_Msk (1UL << SCB_CCR_USERSETMPEND_Pos) /*!< SCB CCR: USERSETMPEND Mask */ + +/* SCB System Handler Control and State Register Definitions */ +#define SCB_SHCSR_HARDFAULTPENDED_Pos 21U /*!< SCB SHCSR: HARDFAULTPENDED Position */ +#define SCB_SHCSR_HARDFAULTPENDED_Msk (1UL << SCB_SHCSR_HARDFAULTPENDED_Pos) /*!< SCB SHCSR: HARDFAULTPENDED Mask */ + +#define SCB_SHCSR_SVCALLPENDED_Pos 15U /*!< SCB SHCSR: SVCALLPENDED Position */ +#define SCB_SHCSR_SVCALLPENDED_Msk (1UL << SCB_SHCSR_SVCALLPENDED_Pos) /*!< SCB SHCSR: SVCALLPENDED Mask */ + +#define SCB_SHCSR_SYSTICKACT_Pos 11U /*!< SCB SHCSR: SYSTICKACT Position */ +#define SCB_SHCSR_SYSTICKACT_Msk (1UL << SCB_SHCSR_SYSTICKACT_Pos) /*!< SCB SHCSR: SYSTICKACT Mask */ + +#define SCB_SHCSR_PENDSVACT_Pos 10U /*!< SCB SHCSR: PENDSVACT Position */ +#define SCB_SHCSR_PENDSVACT_Msk (1UL << SCB_SHCSR_PENDSVACT_Pos) /*!< SCB SHCSR: PENDSVACT Mask */ + +#define SCB_SHCSR_SVCALLACT_Pos 7U /*!< SCB SHCSR: SVCALLACT Position */ +#define SCB_SHCSR_SVCALLACT_Msk (1UL << SCB_SHCSR_SVCALLACT_Pos) /*!< SCB SHCSR: SVCALLACT Mask */ + +#define SCB_SHCSR_NMIACT_Pos 5U /*!< SCB SHCSR: NMIACT Position */ +#define SCB_SHCSR_NMIACT_Msk (1UL << SCB_SHCSR_NMIACT_Pos) /*!< SCB SHCSR: NMIACT Mask */ + +#define SCB_SHCSR_HARDFAULTACT_Pos 2U /*!< SCB SHCSR: HARDFAULTACT Position */ +#define SCB_SHCSR_HARDFAULTACT_Msk (1UL << SCB_SHCSR_HARDFAULTACT_Pos) /*!< SCB SHCSR: HARDFAULTACT Mask */ + +/*@} end of group CMSIS_SCB */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SysTick System Tick Timer (SysTick) + \brief Type definitions for the System Timer Registers. + @{ + */ + +/** + \brief Structure type to access the System Timer (SysTick). + */ +typedef struct +{ + __IOM uint32_t CTRL; /*!< Offset: 0x000 (R/W) SysTick Control and Status Register */ + __IOM uint32_t LOAD; /*!< Offset: 0x004 (R/W) SysTick Reload Value Register */ + __IOM uint32_t VAL; /*!< Offset: 0x008 (R/W) SysTick Current Value Register */ + __IM uint32_t CALIB; /*!< Offset: 0x00C (R/ ) SysTick Calibration Register */ +} SysTick_Type; + +/* SysTick Control / Status Register Definitions */ +#define SysTick_CTRL_COUNTFLAG_Pos 16U /*!< SysTick CTRL: COUNTFLAG Position */ +#define SysTick_CTRL_COUNTFLAG_Msk (1UL << SysTick_CTRL_COUNTFLAG_Pos) /*!< SysTick CTRL: COUNTFLAG Mask */ + +#define SysTick_CTRL_CLKSOURCE_Pos 2U /*!< SysTick CTRL: CLKSOURCE Position */ +#define SysTick_CTRL_CLKSOURCE_Msk (1UL << SysTick_CTRL_CLKSOURCE_Pos) /*!< SysTick CTRL: CLKSOURCE Mask */ + +#define SysTick_CTRL_TICKINT_Pos 1U /*!< SysTick CTRL: TICKINT Position */ +#define SysTick_CTRL_TICKINT_Msk (1UL << SysTick_CTRL_TICKINT_Pos) /*!< SysTick CTRL: TICKINT Mask */ + +#define SysTick_CTRL_ENABLE_Pos 0U /*!< SysTick CTRL: ENABLE Position */ +#define SysTick_CTRL_ENABLE_Msk (1UL /*<< SysTick_CTRL_ENABLE_Pos*/) /*!< SysTick CTRL: ENABLE Mask */ + +/* SysTick Reload Register Definitions */ +#define SysTick_LOAD_RELOAD_Pos 0U /*!< SysTick LOAD: RELOAD Position */ +#define SysTick_LOAD_RELOAD_Msk (0xFFFFFFUL /*<< SysTick_LOAD_RELOAD_Pos*/) /*!< SysTick LOAD: RELOAD Mask */ + +/* SysTick Current Register Definitions */ +#define SysTick_VAL_CURRENT_Pos 0U /*!< SysTick VAL: CURRENT Position */ +#define SysTick_VAL_CURRENT_Msk (0xFFFFFFUL /*<< SysTick_VAL_CURRENT_Pos*/) /*!< SysTick VAL: CURRENT Mask */ + +/* SysTick Calibration Register Definitions */ +#define SysTick_CALIB_NOREF_Pos 31U /*!< SysTick CALIB: NOREF Position */ +#define SysTick_CALIB_NOREF_Msk (1UL << SysTick_CALIB_NOREF_Pos) /*!< SysTick CALIB: NOREF Mask */ + +#define SysTick_CALIB_SKEW_Pos 30U /*!< SysTick CALIB: SKEW Position */ +#define SysTick_CALIB_SKEW_Msk (1UL << SysTick_CALIB_SKEW_Pos) /*!< SysTick CALIB: SKEW Mask */ + +#define SysTick_CALIB_TENMS_Pos 0U /*!< SysTick CALIB: TENMS Position */ +#define SysTick_CALIB_TENMS_Msk (0xFFFFFFUL /*<< SysTick_CALIB_TENMS_Pos*/) /*!< SysTick CALIB: TENMS Mask */ + +/*@} end of group CMSIS_SysTick */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_DWT Data Watchpoint and Trace (DWT) + \brief Type definitions for the Data Watchpoint and Trace (DWT) + @{ + */ + +/** + \brief Structure type to access the Data Watchpoint and Trace Register (DWT). + */ +typedef struct +{ + __IOM uint32_t CTRL; /*!< Offset: 0x000 (R/W) Control Register */ + uint32_t RESERVED0[6U]; + __IM uint32_t PCSR; /*!< Offset: 0x01C (R/ ) Program Counter Sample Register */ + __IOM uint32_t COMP0; /*!< Offset: 0x020 (R/W) Comparator Register 0 */ + uint32_t RESERVED1[1U]; + __IOM uint32_t FUNCTION0; /*!< Offset: 0x028 (R/W) Function Register 0 */ + uint32_t RESERVED2[1U]; + __IOM uint32_t COMP1; /*!< Offset: 0x030 (R/W) Comparator Register 1 */ + uint32_t RESERVED3[1U]; + __IOM uint32_t FUNCTION1; /*!< Offset: 0x038 (R/W) Function Register 1 */ + uint32_t RESERVED4[1U]; + __IOM uint32_t COMP2; /*!< Offset: 0x040 (R/W) Comparator Register 2 */ + uint32_t RESERVED5[1U]; + __IOM uint32_t FUNCTION2; /*!< Offset: 0x048 (R/W) Function Register 2 */ + uint32_t RESERVED6[1U]; + __IOM uint32_t COMP3; /*!< Offset: 0x050 (R/W) Comparator Register 3 */ + uint32_t RESERVED7[1U]; + __IOM uint32_t FUNCTION3; /*!< Offset: 0x058 (R/W) Function Register 3 */ + uint32_t RESERVED8[1U]; + __IOM uint32_t COMP4; /*!< Offset: 0x060 (R/W) Comparator Register 4 */ + uint32_t RESERVED9[1U]; + __IOM uint32_t FUNCTION4; /*!< Offset: 0x068 (R/W) Function Register 4 */ + uint32_t RESERVED10[1U]; + __IOM uint32_t COMP5; /*!< Offset: 0x070 (R/W) Comparator Register 5 */ + uint32_t RESERVED11[1U]; + __IOM uint32_t FUNCTION5; /*!< Offset: 0x078 (R/W) Function Register 5 */ + uint32_t RESERVED12[1U]; + __IOM uint32_t COMP6; /*!< Offset: 0x080 (R/W) Comparator Register 6 */ + uint32_t RESERVED13[1U]; + __IOM uint32_t FUNCTION6; /*!< Offset: 0x088 (R/W) Function Register 6 */ + uint32_t RESERVED14[1U]; + __IOM uint32_t COMP7; /*!< Offset: 0x090 (R/W) Comparator Register 7 */ + uint32_t RESERVED15[1U]; + __IOM uint32_t FUNCTION7; /*!< Offset: 0x098 (R/W) Function Register 7 */ + uint32_t RESERVED16[1U]; + __IOM uint32_t COMP8; /*!< Offset: 0x0A0 (R/W) Comparator Register 8 */ + uint32_t RESERVED17[1U]; + __IOM uint32_t FUNCTION8; /*!< Offset: 0x0A8 (R/W) Function Register 8 */ + uint32_t RESERVED18[1U]; + __IOM uint32_t COMP9; /*!< Offset: 0x0B0 (R/W) Comparator Register 9 */ + uint32_t RESERVED19[1U]; + __IOM uint32_t FUNCTION9; /*!< Offset: 0x0B8 (R/W) Function Register 9 */ + uint32_t RESERVED20[1U]; + __IOM uint32_t COMP10; /*!< Offset: 0x0C0 (R/W) Comparator Register 10 */ + uint32_t RESERVED21[1U]; + __IOM uint32_t FUNCTION10; /*!< Offset: 0x0C8 (R/W) Function Register 10 */ + uint32_t RESERVED22[1U]; + __IOM uint32_t COMP11; /*!< Offset: 0x0D0 (R/W) Comparator Register 11 */ + uint32_t RESERVED23[1U]; + __IOM uint32_t FUNCTION11; /*!< Offset: 0x0D8 (R/W) Function Register 11 */ + uint32_t RESERVED24[1U]; + __IOM uint32_t COMP12; /*!< Offset: 0x0E0 (R/W) Comparator Register 12 */ + uint32_t RESERVED25[1U]; + __IOM uint32_t FUNCTION12; /*!< Offset: 0x0E8 (R/W) Function Register 12 */ + uint32_t RESERVED26[1U]; + __IOM uint32_t COMP13; /*!< Offset: 0x0F0 (R/W) Comparator Register 13 */ + uint32_t RESERVED27[1U]; + __IOM uint32_t FUNCTION13; /*!< Offset: 0x0F8 (R/W) Function Register 13 */ + uint32_t RESERVED28[1U]; + __IOM uint32_t COMP14; /*!< Offset: 0x100 (R/W) Comparator Register 14 */ + uint32_t RESERVED29[1U]; + __IOM uint32_t FUNCTION14; /*!< Offset: 0x108 (R/W) Function Register 14 */ + uint32_t RESERVED30[1U]; + __IOM uint32_t COMP15; /*!< Offset: 0x110 (R/W) Comparator Register 15 */ + uint32_t RESERVED31[1U]; + __IOM uint32_t FUNCTION15; /*!< Offset: 0x118 (R/W) Function Register 15 */ +} DWT_Type; + +/* DWT Control Register Definitions */ +#define DWT_CTRL_NUMCOMP_Pos 28U /*!< DWT CTRL: NUMCOMP Position */ +#define DWT_CTRL_NUMCOMP_Msk (0xFUL << DWT_CTRL_NUMCOMP_Pos) /*!< DWT CTRL: NUMCOMP Mask */ + +#define DWT_CTRL_NOTRCPKT_Pos 27U /*!< DWT CTRL: NOTRCPKT Position */ +#define DWT_CTRL_NOTRCPKT_Msk (0x1UL << DWT_CTRL_NOTRCPKT_Pos) /*!< DWT CTRL: NOTRCPKT Mask */ + +#define DWT_CTRL_NOEXTTRIG_Pos 26U /*!< DWT CTRL: NOEXTTRIG Position */ +#define DWT_CTRL_NOEXTTRIG_Msk (0x1UL << DWT_CTRL_NOEXTTRIG_Pos) /*!< DWT CTRL: NOEXTTRIG Mask */ + +#define DWT_CTRL_NOCYCCNT_Pos 25U /*!< DWT CTRL: NOCYCCNT Position */ +#define DWT_CTRL_NOCYCCNT_Msk (0x1UL << DWT_CTRL_NOCYCCNT_Pos) /*!< DWT CTRL: NOCYCCNT Mask */ + +#define DWT_CTRL_NOPRFCNT_Pos 24U /*!< DWT CTRL: NOPRFCNT Position */ +#define DWT_CTRL_NOPRFCNT_Msk (0x1UL << DWT_CTRL_NOPRFCNT_Pos) /*!< DWT CTRL: NOPRFCNT Mask */ + +/* DWT Comparator Function Register Definitions */ +#define DWT_FUNCTION_ID_Pos 27U /*!< DWT FUNCTION: ID Position */ +#define DWT_FUNCTION_ID_Msk (0x1FUL << DWT_FUNCTION_ID_Pos) /*!< DWT FUNCTION: ID Mask */ + +#define DWT_FUNCTION_MATCHED_Pos 24U /*!< DWT FUNCTION: MATCHED Position */ +#define DWT_FUNCTION_MATCHED_Msk (0x1UL << DWT_FUNCTION_MATCHED_Pos) /*!< DWT FUNCTION: MATCHED Mask */ + +#define DWT_FUNCTION_DATAVSIZE_Pos 10U /*!< DWT FUNCTION: DATAVSIZE Position */ +#define DWT_FUNCTION_DATAVSIZE_Msk (0x3UL << DWT_FUNCTION_DATAVSIZE_Pos) /*!< DWT FUNCTION: DATAVSIZE Mask */ + +#define DWT_FUNCTION_ACTION_Pos 4U /*!< DWT FUNCTION: ACTION Position */ +#define DWT_FUNCTION_ACTION_Msk (0x3UL << DWT_FUNCTION_ACTION_Pos) /*!< DWT FUNCTION: ACTION Mask */ + +#define DWT_FUNCTION_MATCH_Pos 0U /*!< DWT FUNCTION: MATCH Position */ +#define DWT_FUNCTION_MATCH_Msk (0xFUL /*<< DWT_FUNCTION_MATCH_Pos*/) /*!< DWT FUNCTION: MATCH Mask */ + +/*@}*/ /* end of group CMSIS_DWT */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_TPI Trace Port Interface (TPI) + \brief Type definitions for the Trace Port Interface (TPI) + @{ + */ + +/** + \brief Structure type to access the Trace Port Interface Register (TPI). + */ +typedef struct +{ + __IM uint32_t SSPSR; /*!< Offset: 0x000 (R/ ) Supported Parallel Port Size Register */ + __IOM uint32_t CSPSR; /*!< Offset: 0x004 (R/W) Current Parallel Port Size Register */ + uint32_t RESERVED0[2U]; + __IOM uint32_t ACPR; /*!< Offset: 0x010 (R/W) Asynchronous Clock Prescaler Register */ + uint32_t RESERVED1[55U]; + __IOM uint32_t SPPR; /*!< Offset: 0x0F0 (R/W) Selected Pin Protocol Register */ + uint32_t RESERVED2[131U]; + __IM uint32_t FFSR; /*!< Offset: 0x300 (R/ ) Formatter and Flush Status Register */ + __IOM uint32_t FFCR; /*!< Offset: 0x304 (R/W) Formatter and Flush Control Register */ + __IOM uint32_t PSCR; /*!< Offset: 0x308 (R/W) Periodic Synchronization Control Register */ + uint32_t RESERVED3[759U]; + __IM uint32_t TRIGGER; /*!< Offset: 0xEE8 (R/ ) TRIGGER Register */ + __IM uint32_t ITFTTD0; /*!< Offset: 0xEEC (R/ ) Integration Test FIFO Test Data 0 Register */ + __IOM uint32_t ITATBCTR2; /*!< Offset: 0xEF0 (R/W) Integration Test ATB Control Register 2 */ + uint32_t RESERVED4[1U]; + __IM uint32_t ITATBCTR0; /*!< Offset: 0xEF8 (R/ ) Integration Test ATB Control Register 0 */ + __IM uint32_t ITFTTD1; /*!< Offset: 0xEFC (R/ ) Integration Test FIFO Test Data 1 Register */ + __IOM uint32_t ITCTRL; /*!< Offset: 0xF00 (R/W) Integration Mode Control */ + uint32_t RESERVED5[39U]; + __IOM uint32_t CLAIMSET; /*!< Offset: 0xFA0 (R/W) Claim tag set */ + __IOM uint32_t CLAIMCLR; /*!< Offset: 0xFA4 (R/W) Claim tag clear */ + uint32_t RESERVED7[8U]; + __IM uint32_t DEVID; /*!< Offset: 0xFC8 (R/ ) Device Configuration Register */ + __IM uint32_t DEVTYPE; /*!< Offset: 0xFCC (R/ ) Device Type Identifier Register */ +} TPI_Type; + +/* TPI Asynchronous Clock Prescaler Register Definitions */ +#define TPI_ACPR_PRESCALER_Pos 0U /*!< TPI ACPR: PRESCALER Position */ +#define TPI_ACPR_PRESCALER_Msk (0x1FFFUL /*<< TPI_ACPR_PRESCALER_Pos*/) /*!< TPI ACPR: PRESCALER Mask */ + +/* TPI Selected Pin Protocol Register Definitions */ +#define TPI_SPPR_TXMODE_Pos 0U /*!< TPI SPPR: TXMODE Position */ +#define TPI_SPPR_TXMODE_Msk (0x3UL /*<< TPI_SPPR_TXMODE_Pos*/) /*!< TPI SPPR: TXMODE Mask */ + +/* TPI Formatter and Flush Status Register Definitions */ +#define TPI_FFSR_FtNonStop_Pos 3U /*!< TPI FFSR: FtNonStop Position */ +#define TPI_FFSR_FtNonStop_Msk (0x1UL << TPI_FFSR_FtNonStop_Pos) /*!< TPI FFSR: FtNonStop Mask */ + +#define TPI_FFSR_TCPresent_Pos 2U /*!< TPI FFSR: TCPresent Position */ +#define TPI_FFSR_TCPresent_Msk (0x1UL << TPI_FFSR_TCPresent_Pos) /*!< TPI FFSR: TCPresent Mask */ + +#define TPI_FFSR_FtStopped_Pos 1U /*!< TPI FFSR: FtStopped Position */ +#define TPI_FFSR_FtStopped_Msk (0x1UL << TPI_FFSR_FtStopped_Pos) /*!< TPI FFSR: FtStopped Mask */ + +#define TPI_FFSR_FlInProg_Pos 0U /*!< TPI FFSR: FlInProg Position */ +#define TPI_FFSR_FlInProg_Msk (0x1UL /*<< TPI_FFSR_FlInProg_Pos*/) /*!< TPI FFSR: FlInProg Mask */ + +/* TPI Formatter and Flush Control Register Definitions */ +#define TPI_FFCR_TrigIn_Pos 8U /*!< TPI FFCR: TrigIn Position */ +#define TPI_FFCR_TrigIn_Msk (0x1UL << TPI_FFCR_TrigIn_Pos) /*!< TPI FFCR: TrigIn Mask */ + +#define TPI_FFCR_FOnMan_Pos 6U /*!< TPI FFCR: FOnMan Position */ +#define TPI_FFCR_FOnMan_Msk (0x1UL << TPI_FFCR_FOnMan_Pos) /*!< TPI FFCR: FOnMan Mask */ + +#define TPI_FFCR_EnFCont_Pos 1U /*!< TPI FFCR: EnFCont Position */ +#define TPI_FFCR_EnFCont_Msk (0x1UL << TPI_FFCR_EnFCont_Pos) /*!< TPI FFCR: EnFCont Mask */ + +/* TPI TRIGGER Register Definitions */ +#define TPI_TRIGGER_TRIGGER_Pos 0U /*!< TPI TRIGGER: TRIGGER Position */ +#define TPI_TRIGGER_TRIGGER_Msk (0x1UL /*<< TPI_TRIGGER_TRIGGER_Pos*/) /*!< TPI TRIGGER: TRIGGER Mask */ + +/* TPI Integration Test FIFO Test Data 0 Register Definitions */ +#define TPI_ITFTTD0_ATB_IF2_ATVALID_Pos 29U /*!< TPI ITFTTD0: ATB Interface 2 ATVALIDPosition */ +#define TPI_ITFTTD0_ATB_IF2_ATVALID_Msk (0x3UL << TPI_ITFTTD0_ATB_IF2_ATVALID_Pos) /*!< TPI ITFTTD0: ATB Interface 2 ATVALID Mask */ + +#define TPI_ITFTTD0_ATB_IF2_bytecount_Pos 27U /*!< TPI ITFTTD0: ATB Interface 2 byte count Position */ +#define TPI_ITFTTD0_ATB_IF2_bytecount_Msk (0x3UL << TPI_ITFTTD0_ATB_IF2_bytecount_Pos) /*!< TPI ITFTTD0: ATB Interface 2 byte count Mask */ + +#define TPI_ITFTTD0_ATB_IF1_ATVALID_Pos 26U /*!< TPI ITFTTD0: ATB Interface 1 ATVALID Position */ +#define TPI_ITFTTD0_ATB_IF1_ATVALID_Msk (0x3UL << TPI_ITFTTD0_ATB_IF1_ATVALID_Pos) /*!< TPI ITFTTD0: ATB Interface 1 ATVALID Mask */ + +#define TPI_ITFTTD0_ATB_IF1_bytecount_Pos 24U /*!< TPI ITFTTD0: ATB Interface 1 byte count Position */ +#define TPI_ITFTTD0_ATB_IF1_bytecount_Msk (0x3UL << TPI_ITFTTD0_ATB_IF1_bytecount_Pos) /*!< TPI ITFTTD0: ATB Interface 1 byte countt Mask */ + +#define TPI_ITFTTD0_ATB_IF1_data2_Pos 16U /*!< TPI ITFTTD0: ATB Interface 1 data2 Position */ +#define TPI_ITFTTD0_ATB_IF1_data2_Msk (0xFFUL << TPI_ITFTTD0_ATB_IF1_data1_Pos) /*!< TPI ITFTTD0: ATB Interface 1 data2 Mask */ + +#define TPI_ITFTTD0_ATB_IF1_data1_Pos 8U /*!< TPI ITFTTD0: ATB Interface 1 data1 Position */ +#define TPI_ITFTTD0_ATB_IF1_data1_Msk (0xFFUL << TPI_ITFTTD0_ATB_IF1_data1_Pos) /*!< TPI ITFTTD0: ATB Interface 1 data1 Mask */ + +#define TPI_ITFTTD0_ATB_IF1_data0_Pos 0U /*!< TPI ITFTTD0: ATB Interface 1 data0 Position */ +#define TPI_ITFTTD0_ATB_IF1_data0_Msk (0xFFUL /*<< TPI_ITFTTD0_ATB_IF1_data0_Pos*/) /*!< TPI ITFTTD0: ATB Interface 1 data0 Mask */ + +/* TPI Integration Test ATB Control Register 2 Register Definitions */ +#define TPI_ITATBCTR2_AFVALID2S_Pos 1U /*!< TPI ITATBCTR2: AFVALID2S Position */ +#define TPI_ITATBCTR2_AFVALID2S_Msk (0x1UL << TPI_ITATBCTR2_AFVALID2S_Pos) /*!< TPI ITATBCTR2: AFVALID2SS Mask */ + +#define TPI_ITATBCTR2_AFVALID1S_Pos 1U /*!< TPI ITATBCTR2: AFVALID1S Position */ +#define TPI_ITATBCTR2_AFVALID1S_Msk (0x1UL << TPI_ITATBCTR2_AFVALID1S_Pos) /*!< TPI ITATBCTR2: AFVALID1SS Mask */ + +#define TPI_ITATBCTR2_ATREADY2S_Pos 0U /*!< TPI ITATBCTR2: ATREADY2S Position */ +#define TPI_ITATBCTR2_ATREADY2S_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY2S_Pos*/) /*!< TPI ITATBCTR2: ATREADY2S Mask */ + +#define TPI_ITATBCTR2_ATREADY1S_Pos 0U /*!< TPI ITATBCTR2: ATREADY1S Position */ +#define TPI_ITATBCTR2_ATREADY1S_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY1S_Pos*/) /*!< TPI ITATBCTR2: ATREADY1S Mask */ + +/* TPI Integration Test FIFO Test Data 1 Register Definitions */ +#define TPI_ITFTTD1_ATB_IF2_ATVALID_Pos 29U /*!< TPI ITFTTD1: ATB Interface 2 ATVALID Position */ +#define TPI_ITFTTD1_ATB_IF2_ATVALID_Msk (0x3UL << TPI_ITFTTD1_ATB_IF2_ATVALID_Pos) /*!< TPI ITFTTD1: ATB Interface 2 ATVALID Mask */ + +#define TPI_ITFTTD1_ATB_IF2_bytecount_Pos 27U /*!< TPI ITFTTD1: ATB Interface 2 byte count Position */ +#define TPI_ITFTTD1_ATB_IF2_bytecount_Msk (0x3UL << TPI_ITFTTD1_ATB_IF2_bytecount_Pos) /*!< TPI ITFTTD1: ATB Interface 2 byte count Mask */ + +#define TPI_ITFTTD1_ATB_IF1_ATVALID_Pos 26U /*!< TPI ITFTTD1: ATB Interface 1 ATVALID Position */ +#define TPI_ITFTTD1_ATB_IF1_ATVALID_Msk (0x3UL << TPI_ITFTTD1_ATB_IF1_ATVALID_Pos) /*!< TPI ITFTTD1: ATB Interface 1 ATVALID Mask */ + +#define TPI_ITFTTD1_ATB_IF1_bytecount_Pos 24U /*!< TPI ITFTTD1: ATB Interface 1 byte count Position */ +#define TPI_ITFTTD1_ATB_IF1_bytecount_Msk (0x3UL << TPI_ITFTTD1_ATB_IF1_bytecount_Pos) /*!< TPI ITFTTD1: ATB Interface 1 byte countt Mask */ + +#define TPI_ITFTTD1_ATB_IF2_data2_Pos 16U /*!< TPI ITFTTD1: ATB Interface 2 data2 Position */ +#define TPI_ITFTTD1_ATB_IF2_data2_Msk (0xFFUL << TPI_ITFTTD1_ATB_IF2_data1_Pos) /*!< TPI ITFTTD1: ATB Interface 2 data2 Mask */ + +#define TPI_ITFTTD1_ATB_IF2_data1_Pos 8U /*!< TPI ITFTTD1: ATB Interface 2 data1 Position */ +#define TPI_ITFTTD1_ATB_IF2_data1_Msk (0xFFUL << TPI_ITFTTD1_ATB_IF2_data1_Pos) /*!< TPI ITFTTD1: ATB Interface 2 data1 Mask */ + +#define TPI_ITFTTD1_ATB_IF2_data0_Pos 0U /*!< TPI ITFTTD1: ATB Interface 2 data0 Position */ +#define TPI_ITFTTD1_ATB_IF2_data0_Msk (0xFFUL /*<< TPI_ITFTTD1_ATB_IF2_data0_Pos*/) /*!< TPI ITFTTD1: ATB Interface 2 data0 Mask */ + +/* TPI Integration Test ATB Control Register 0 Definitions */ +#define TPI_ITATBCTR0_AFVALID2S_Pos 1U /*!< TPI ITATBCTR0: AFVALID2S Position */ +#define TPI_ITATBCTR0_AFVALID2S_Msk (0x1UL << TPI_ITATBCTR0_AFVALID2S_Pos) /*!< TPI ITATBCTR0: AFVALID2SS Mask */ + +#define TPI_ITATBCTR0_AFVALID1S_Pos 1U /*!< TPI ITATBCTR0: AFVALID1S Position */ +#define TPI_ITATBCTR0_AFVALID1S_Msk (0x1UL << TPI_ITATBCTR0_AFVALID1S_Pos) /*!< TPI ITATBCTR0: AFVALID1SS Mask */ + +#define TPI_ITATBCTR0_ATREADY2S_Pos 0U /*!< TPI ITATBCTR0: ATREADY2S Position */ +#define TPI_ITATBCTR0_ATREADY2S_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY2S_Pos*/) /*!< TPI ITATBCTR0: ATREADY2S Mask */ + +#define TPI_ITATBCTR0_ATREADY1S_Pos 0U /*!< TPI ITATBCTR0: ATREADY1S Position */ +#define TPI_ITATBCTR0_ATREADY1S_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY1S_Pos*/) /*!< TPI ITATBCTR0: ATREADY1S Mask */ + +/* TPI Integration Mode Control Register Definitions */ +#define TPI_ITCTRL_Mode_Pos 0U /*!< TPI ITCTRL: Mode Position */ +#define TPI_ITCTRL_Mode_Msk (0x3UL /*<< TPI_ITCTRL_Mode_Pos*/) /*!< TPI ITCTRL: Mode Mask */ + +/* TPI DEVID Register Definitions */ +#define TPI_DEVID_NRZVALID_Pos 11U /*!< TPI DEVID: NRZVALID Position */ +#define TPI_DEVID_NRZVALID_Msk (0x1UL << TPI_DEVID_NRZVALID_Pos) /*!< TPI DEVID: NRZVALID Mask */ + +#define TPI_DEVID_MANCVALID_Pos 10U /*!< TPI DEVID: MANCVALID Position */ +#define TPI_DEVID_MANCVALID_Msk (0x1UL << TPI_DEVID_MANCVALID_Pos) /*!< TPI DEVID: MANCVALID Mask */ + +#define TPI_DEVID_PTINVALID_Pos 9U /*!< TPI DEVID: PTINVALID Position */ +#define TPI_DEVID_PTINVALID_Msk (0x1UL << TPI_DEVID_PTINVALID_Pos) /*!< TPI DEVID: PTINVALID Mask */ + +#define TPI_DEVID_FIFOSZ_Pos 6U /*!< TPI DEVID: FIFOSZ Position */ +#define TPI_DEVID_FIFOSZ_Msk (0x7UL << TPI_DEVID_FIFOSZ_Pos) /*!< TPI DEVID: FIFOSZ Mask */ + +#define TPI_DEVID_NrTraceInput_Pos 0U /*!< TPI DEVID: NrTraceInput Position */ +#define TPI_DEVID_NrTraceInput_Msk (0x3FUL /*<< TPI_DEVID_NrTraceInput_Pos*/) /*!< TPI DEVID: NrTraceInput Mask */ + +/* TPI DEVTYPE Register Definitions */ +#define TPI_DEVTYPE_SubType_Pos 4U /*!< TPI DEVTYPE: SubType Position */ +#define TPI_DEVTYPE_SubType_Msk (0xFUL /*<< TPI_DEVTYPE_SubType_Pos*/) /*!< TPI DEVTYPE: SubType Mask */ + +#define TPI_DEVTYPE_MajorType_Pos 0U /*!< TPI DEVTYPE: MajorType Position */ +#define TPI_DEVTYPE_MajorType_Msk (0xFUL << TPI_DEVTYPE_MajorType_Pos) /*!< TPI DEVTYPE: MajorType Mask */ + +/*@}*/ /* end of group CMSIS_TPI */ + + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_MPU Memory Protection Unit (MPU) + \brief Type definitions for the Memory Protection Unit (MPU) + @{ + */ + +/** + \brief Structure type to access the Memory Protection Unit (MPU). + */ +typedef struct +{ + __IM uint32_t TYPE; /*!< Offset: 0x000 (R/ ) MPU Type Register */ + __IOM uint32_t CTRL; /*!< Offset: 0x004 (R/W) MPU Control Register */ + __IOM uint32_t RNR; /*!< Offset: 0x008 (R/W) MPU Region Number Register */ + __IOM uint32_t RBAR; /*!< Offset: 0x00C (R/W) MPU Region Base Address Register */ + __IOM uint32_t RLAR; /*!< Offset: 0x010 (R/W) MPU Region Limit Address Register */ + uint32_t RESERVED0[7U]; + union + { + __IOM uint32_t MAIR[2]; + struct + { + __IOM uint32_t MAIR0; /*!< Offset: 0x030 (R/W) MPU Memory Attribute Indirection Register 0 */ + __IOM uint32_t MAIR1; /*!< Offset: 0x034 (R/W) MPU Memory Attribute Indirection Register 1 */ + }; + }; +} MPU_Type; + +#define MPU_TYPE_RALIASES 1U + +/* MPU Type Register Definitions */ +#define MPU_TYPE_IREGION_Pos 16U /*!< MPU TYPE: IREGION Position */ +#define MPU_TYPE_IREGION_Msk (0xFFUL << MPU_TYPE_IREGION_Pos) /*!< MPU TYPE: IREGION Mask */ + +#define MPU_TYPE_DREGION_Pos 8U /*!< MPU TYPE: DREGION Position */ +#define MPU_TYPE_DREGION_Msk (0xFFUL << MPU_TYPE_DREGION_Pos) /*!< MPU TYPE: DREGION Mask */ + +#define MPU_TYPE_SEPARATE_Pos 0U /*!< MPU TYPE: SEPARATE Position */ +#define MPU_TYPE_SEPARATE_Msk (1UL /*<< MPU_TYPE_SEPARATE_Pos*/) /*!< MPU TYPE: SEPARATE Mask */ + +/* MPU Control Register Definitions */ +#define MPU_CTRL_PRIVDEFENA_Pos 2U /*!< MPU CTRL: PRIVDEFENA Position */ +#define MPU_CTRL_PRIVDEFENA_Msk (1UL << MPU_CTRL_PRIVDEFENA_Pos) /*!< MPU CTRL: PRIVDEFENA Mask */ + +#define MPU_CTRL_HFNMIENA_Pos 1U /*!< MPU CTRL: HFNMIENA Position */ +#define MPU_CTRL_HFNMIENA_Msk (1UL << MPU_CTRL_HFNMIENA_Pos) /*!< MPU CTRL: HFNMIENA Mask */ + +#define MPU_CTRL_ENABLE_Pos 0U /*!< MPU CTRL: ENABLE Position */ +#define MPU_CTRL_ENABLE_Msk (1UL /*<< MPU_CTRL_ENABLE_Pos*/) /*!< MPU CTRL: ENABLE Mask */ + +/* MPU Region Number Register Definitions */ +#define MPU_RNR_REGION_Pos 0U /*!< MPU RNR: REGION Position */ +#define MPU_RNR_REGION_Msk (0xFFUL /*<< MPU_RNR_REGION_Pos*/) /*!< MPU RNR: REGION Mask */ + +/* MPU Region Base Address Register Definitions */ +#define MPU_RBAR_BASE_Pos 5U /*!< MPU RBAR: BASE Position */ +#define MPU_RBAR_BASE_Msk (0x7FFFFFFUL << MPU_RBAR_BASE_Pos) /*!< MPU RBAR: BASE Mask */ + +#define MPU_RBAR_SH_Pos 3U /*!< MPU RBAR: SH Position */ +#define MPU_RBAR_SH_Msk (0x3UL << MPU_RBAR_SH_Pos) /*!< MPU RBAR: SH Mask */ + +#define MPU_RBAR_AP_Pos 1U /*!< MPU RBAR: AP Position */ +#define MPU_RBAR_AP_Msk (0x3UL << MPU_RBAR_AP_Pos) /*!< MPU RBAR: AP Mask */ + +#define MPU_RBAR_XN_Pos 0U /*!< MPU RBAR: XN Position */ +#define MPU_RBAR_XN_Msk (01UL /*<< MPU_RBAR_XN_Pos*/) /*!< MPU RBAR: XN Mask */ + +/* MPU Region Limit Address Register Definitions */ +#define MPU_RLAR_LIMIT_Pos 5U /*!< MPU RLAR: LIMIT Position */ +#define MPU_RLAR_LIMIT_Msk (0x7FFFFFFUL << MPU_RLAR_LIMIT_Pos) /*!< MPU RLAR: LIMIT Mask */ + +#define MPU_RLAR_AttrIndx_Pos 1U /*!< MPU RLAR: AttrIndx Position */ +#define MPU_RLAR_AttrIndx_Msk (0x7UL << MPU_RLAR_AttrIndx_Pos) /*!< MPU RLAR: AttrIndx Mask */ + +#define MPU_RLAR_EN_Pos 0U /*!< MPU RLAR: EN Position */ +#define MPU_RLAR_EN_Msk (1UL /*<< MPU_RLAR_EN_Pos*/) /*!< MPU RLAR: EN Mask */ + +/* MPU Memory Attribute Indirection Register 0 Definitions */ +#define MPU_MAIR0_Attr3_Pos 24U /*!< MPU MAIR0: Attr3 Position */ +#define MPU_MAIR0_Attr3_Msk (0xFFUL << MPU_MAIR0_Attr3_Pos) /*!< MPU MAIR0: Attr3 Mask */ + +#define MPU_MAIR0_Attr2_Pos 16U /*!< MPU MAIR0: Attr2 Position */ +#define MPU_MAIR0_Attr2_Msk (0xFFUL << MPU_MAIR0_Attr2_Pos) /*!< MPU MAIR0: Attr2 Mask */ + +#define MPU_MAIR0_Attr1_Pos 8U /*!< MPU MAIR0: Attr1 Position */ +#define MPU_MAIR0_Attr1_Msk (0xFFUL << MPU_MAIR0_Attr1_Pos) /*!< MPU MAIR0: Attr1 Mask */ + +#define MPU_MAIR0_Attr0_Pos 0U /*!< MPU MAIR0: Attr0 Position */ +#define MPU_MAIR0_Attr0_Msk (0xFFUL /*<< MPU_MAIR0_Attr0_Pos*/) /*!< MPU MAIR0: Attr0 Mask */ + +/* MPU Memory Attribute Indirection Register 1 Definitions */ +#define MPU_MAIR1_Attr7_Pos 24U /*!< MPU MAIR1: Attr7 Position */ +#define MPU_MAIR1_Attr7_Msk (0xFFUL << MPU_MAIR1_Attr7_Pos) /*!< MPU MAIR1: Attr7 Mask */ + +#define MPU_MAIR1_Attr6_Pos 16U /*!< MPU MAIR1: Attr6 Position */ +#define MPU_MAIR1_Attr6_Msk (0xFFUL << MPU_MAIR1_Attr6_Pos) /*!< MPU MAIR1: Attr6 Mask */ + +#define MPU_MAIR1_Attr5_Pos 8U /*!< MPU MAIR1: Attr5 Position */ +#define MPU_MAIR1_Attr5_Msk (0xFFUL << MPU_MAIR1_Attr5_Pos) /*!< MPU MAIR1: Attr5 Mask */ + +#define MPU_MAIR1_Attr4_Pos 0U /*!< MPU MAIR1: Attr4 Position */ +#define MPU_MAIR1_Attr4_Msk (0xFFUL /*<< MPU_MAIR1_Attr4_Pos*/) /*!< MPU MAIR1: Attr4 Mask */ + +/*@} end of group CMSIS_MPU */ +#endif + + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SAU Security Attribution Unit (SAU) + \brief Type definitions for the Security Attribution Unit (SAU) + @{ + */ + +/** + \brief Structure type to access the Security Attribution Unit (SAU). + */ +typedef struct +{ + __IOM uint32_t CTRL; /*!< Offset: 0x000 (R/W) SAU Control Register */ + __IM uint32_t TYPE; /*!< Offset: 0x004 (R/ ) SAU Type Register */ +#if defined (__SAUREGION_PRESENT) && (__SAUREGION_PRESENT == 1U) + __IOM uint32_t RNR; /*!< Offset: 0x008 (R/W) SAU Region Number Register */ + __IOM uint32_t RBAR; /*!< Offset: 0x00C (R/W) SAU Region Base Address Register */ + __IOM uint32_t RLAR; /*!< Offset: 0x010 (R/W) SAU Region Limit Address Register */ +#endif +} SAU_Type; + +/* SAU Control Register Definitions */ +#define SAU_CTRL_ALLNS_Pos 1U /*!< SAU CTRL: ALLNS Position */ +#define SAU_CTRL_ALLNS_Msk (1UL << SAU_CTRL_ALLNS_Pos) /*!< SAU CTRL: ALLNS Mask */ + +#define SAU_CTRL_ENABLE_Pos 0U /*!< SAU CTRL: ENABLE Position */ +#define SAU_CTRL_ENABLE_Msk (1UL /*<< SAU_CTRL_ENABLE_Pos*/) /*!< SAU CTRL: ENABLE Mask */ + +/* SAU Type Register Definitions */ +#define SAU_TYPE_SREGION_Pos 0U /*!< SAU TYPE: SREGION Position */ +#define SAU_TYPE_SREGION_Msk (0xFFUL /*<< SAU_TYPE_SREGION_Pos*/) /*!< SAU TYPE: SREGION Mask */ + +#if defined (__SAUREGION_PRESENT) && (__SAUREGION_PRESENT == 1U) +/* SAU Region Number Register Definitions */ +#define SAU_RNR_REGION_Pos 0U /*!< SAU RNR: REGION Position */ +#define SAU_RNR_REGION_Msk (0xFFUL /*<< SAU_RNR_REGION_Pos*/) /*!< SAU RNR: REGION Mask */ + +/* SAU Region Base Address Register Definitions */ +#define SAU_RBAR_BADDR_Pos 5U /*!< SAU RBAR: BADDR Position */ +#define SAU_RBAR_BADDR_Msk (0x7FFFFFFUL << SAU_RBAR_BADDR_Pos) /*!< SAU RBAR: BADDR Mask */ + +/* SAU Region Limit Address Register Definitions */ +#define SAU_RLAR_LADDR_Pos 5U /*!< SAU RLAR: LADDR Position */ +#define SAU_RLAR_LADDR_Msk (0x7FFFFFFUL << SAU_RLAR_LADDR_Pos) /*!< SAU RLAR: LADDR Mask */ + +#define SAU_RLAR_NSC_Pos 1U /*!< SAU RLAR: NSC Position */ +#define SAU_RLAR_NSC_Msk (1UL << SAU_RLAR_NSC_Pos) /*!< SAU RLAR: NSC Mask */ + +#define SAU_RLAR_ENABLE_Pos 0U /*!< SAU RLAR: ENABLE Position */ +#define SAU_RLAR_ENABLE_Msk (1UL /*<< SAU_RLAR_ENABLE_Pos*/) /*!< SAU RLAR: ENABLE Mask */ + +#endif /* defined (__SAUREGION_PRESENT) && (__SAUREGION_PRESENT == 1U) */ + +/*@} end of group CMSIS_SAU */ +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_CoreDebug Core Debug Registers (CoreDebug) + \brief Type definitions for the Core Debug Registers + @{ + */ + +/** + \brief Structure type to access the Core Debug Register (CoreDebug). + */ +typedef struct +{ + __IOM uint32_t DHCSR; /*!< Offset: 0x000 (R/W) Debug Halting Control and Status Register */ + __OM uint32_t DCRSR; /*!< Offset: 0x004 ( /W) Debug Core Register Selector Register */ + __IOM uint32_t DCRDR; /*!< Offset: 0x008 (R/W) Debug Core Register Data Register */ + __IOM uint32_t DEMCR; /*!< Offset: 0x00C (R/W) Debug Exception and Monitor Control Register */ + uint32_t RESERVED4[1U]; + __IOM uint32_t DAUTHCTRL; /*!< Offset: 0x014 (R/W) Debug Authentication Control Register */ + __IOM uint32_t DSCSR; /*!< Offset: 0x018 (R/W) Debug Security Control and Status Register */ +} CoreDebug_Type; + +/* Debug Halting Control and Status Register Definitions */ +#define CoreDebug_DHCSR_DBGKEY_Pos 16U /*!< CoreDebug DHCSR: DBGKEY Position */ +#define CoreDebug_DHCSR_DBGKEY_Msk (0xFFFFUL << CoreDebug_DHCSR_DBGKEY_Pos) /*!< CoreDebug DHCSR: DBGKEY Mask */ + +#define CoreDebug_DHCSR_S_RESTART_ST_Pos 26U /*!< CoreDebug DHCSR: S_RESTART_ST Position */ +#define CoreDebug_DHCSR_S_RESTART_ST_Msk (1UL << CoreDebug_DHCSR_S_RESTART_ST_Pos) /*!< CoreDebug DHCSR: S_RESTART_ST Mask */ + +#define CoreDebug_DHCSR_S_RESET_ST_Pos 25U /*!< CoreDebug DHCSR: S_RESET_ST Position */ +#define CoreDebug_DHCSR_S_RESET_ST_Msk (1UL << CoreDebug_DHCSR_S_RESET_ST_Pos) /*!< CoreDebug DHCSR: S_RESET_ST Mask */ + +#define CoreDebug_DHCSR_S_RETIRE_ST_Pos 24U /*!< CoreDebug DHCSR: S_RETIRE_ST Position */ +#define CoreDebug_DHCSR_S_RETIRE_ST_Msk (1UL << CoreDebug_DHCSR_S_RETIRE_ST_Pos) /*!< CoreDebug DHCSR: S_RETIRE_ST Mask */ + +#define CoreDebug_DHCSR_S_LOCKUP_Pos 19U /*!< CoreDebug DHCSR: S_LOCKUP Position */ +#define CoreDebug_DHCSR_S_LOCKUP_Msk (1UL << CoreDebug_DHCSR_S_LOCKUP_Pos) /*!< CoreDebug DHCSR: S_LOCKUP Mask */ + +#define CoreDebug_DHCSR_S_SLEEP_Pos 18U /*!< CoreDebug DHCSR: S_SLEEP Position */ +#define CoreDebug_DHCSR_S_SLEEP_Msk (1UL << CoreDebug_DHCSR_S_SLEEP_Pos) /*!< CoreDebug DHCSR: S_SLEEP Mask */ + +#define CoreDebug_DHCSR_S_HALT_Pos 17U /*!< CoreDebug DHCSR: S_HALT Position */ +#define CoreDebug_DHCSR_S_HALT_Msk (1UL << CoreDebug_DHCSR_S_HALT_Pos) /*!< CoreDebug DHCSR: S_HALT Mask */ + +#define CoreDebug_DHCSR_S_REGRDY_Pos 16U /*!< CoreDebug DHCSR: S_REGRDY Position */ +#define CoreDebug_DHCSR_S_REGRDY_Msk (1UL << CoreDebug_DHCSR_S_REGRDY_Pos) /*!< CoreDebug DHCSR: S_REGRDY Mask */ + +#define CoreDebug_DHCSR_C_MASKINTS_Pos 3U /*!< CoreDebug DHCSR: C_MASKINTS Position */ +#define CoreDebug_DHCSR_C_MASKINTS_Msk (1UL << CoreDebug_DHCSR_C_MASKINTS_Pos) /*!< CoreDebug DHCSR: C_MASKINTS Mask */ + +#define CoreDebug_DHCSR_C_STEP_Pos 2U /*!< CoreDebug DHCSR: C_STEP Position */ +#define CoreDebug_DHCSR_C_STEP_Msk (1UL << CoreDebug_DHCSR_C_STEP_Pos) /*!< CoreDebug DHCSR: C_STEP Mask */ + +#define CoreDebug_DHCSR_C_HALT_Pos 1U /*!< CoreDebug DHCSR: C_HALT Position */ +#define CoreDebug_DHCSR_C_HALT_Msk (1UL << CoreDebug_DHCSR_C_HALT_Pos) /*!< CoreDebug DHCSR: C_HALT Mask */ + +#define CoreDebug_DHCSR_C_DEBUGEN_Pos 0U /*!< CoreDebug DHCSR: C_DEBUGEN Position */ +#define CoreDebug_DHCSR_C_DEBUGEN_Msk (1UL /*<< CoreDebug_DHCSR_C_DEBUGEN_Pos*/) /*!< CoreDebug DHCSR: C_DEBUGEN Mask */ + +/* Debug Core Register Selector Register Definitions */ +#define CoreDebug_DCRSR_REGWnR_Pos 16U /*!< CoreDebug DCRSR: REGWnR Position */ +#define CoreDebug_DCRSR_REGWnR_Msk (1UL << CoreDebug_DCRSR_REGWnR_Pos) /*!< CoreDebug DCRSR: REGWnR Mask */ + +#define CoreDebug_DCRSR_REGSEL_Pos 0U /*!< CoreDebug DCRSR: REGSEL Position */ +#define CoreDebug_DCRSR_REGSEL_Msk (0x1FUL /*<< CoreDebug_DCRSR_REGSEL_Pos*/) /*!< CoreDebug DCRSR: REGSEL Mask */ + +/* Debug Exception and Monitor Control Register */ +#define CoreDebug_DEMCR_DWTENA_Pos 24U /*!< CoreDebug DEMCR: DWTENA Position */ +#define CoreDebug_DEMCR_DWTENA_Msk (1UL << CoreDebug_DEMCR_DWTENA_Pos) /*!< CoreDebug DEMCR: DWTENA Mask */ + +#define CoreDebug_DEMCR_VC_HARDERR_Pos 10U /*!< CoreDebug DEMCR: VC_HARDERR Position */ +#define CoreDebug_DEMCR_VC_HARDERR_Msk (1UL << CoreDebug_DEMCR_VC_HARDERR_Pos) /*!< CoreDebug DEMCR: VC_HARDERR Mask */ + +#define CoreDebug_DEMCR_VC_CORERESET_Pos 0U /*!< CoreDebug DEMCR: VC_CORERESET Position */ +#define CoreDebug_DEMCR_VC_CORERESET_Msk (1UL /*<< CoreDebug_DEMCR_VC_CORERESET_Pos*/) /*!< CoreDebug DEMCR: VC_CORERESET Mask */ + +/* Debug Authentication Control Register Definitions */ +#define CoreDebug_DAUTHCTRL_INTSPNIDEN_Pos 3U /*!< CoreDebug DAUTHCTRL: INTSPNIDEN, Position */ +#define CoreDebug_DAUTHCTRL_INTSPNIDEN_Msk (1UL << CoreDebug_DAUTHCTRL_INTSPNIDEN_Pos) /*!< CoreDebug DAUTHCTRL: INTSPNIDEN, Mask */ + +#define CoreDebug_DAUTHCTRL_SPNIDENSEL_Pos 2U /*!< CoreDebug DAUTHCTRL: SPNIDENSEL Position */ +#define CoreDebug_DAUTHCTRL_SPNIDENSEL_Msk (1UL << CoreDebug_DAUTHCTRL_SPNIDENSEL_Pos) /*!< CoreDebug DAUTHCTRL: SPNIDENSEL Mask */ + +#define CoreDebug_DAUTHCTRL_INTSPIDEN_Pos 1U /*!< CoreDebug DAUTHCTRL: INTSPIDEN Position */ +#define CoreDebug_DAUTHCTRL_INTSPIDEN_Msk (1UL << CoreDebug_DAUTHCTRL_INTSPIDEN_Pos) /*!< CoreDebug DAUTHCTRL: INTSPIDEN Mask */ + +#define CoreDebug_DAUTHCTRL_SPIDENSEL_Pos 0U /*!< CoreDebug DAUTHCTRL: SPIDENSEL Position */ +#define CoreDebug_DAUTHCTRL_SPIDENSEL_Msk (1UL /*<< CoreDebug_DAUTHCTRL_SPIDENSEL_Pos*/) /*!< CoreDebug DAUTHCTRL: SPIDENSEL Mask */ + +/* Debug Security Control and Status Register Definitions */ +#define CoreDebug_DSCSR_CDS_Pos 16U /*!< CoreDebug DSCSR: CDS Position */ +#define CoreDebug_DSCSR_CDS_Msk (1UL << CoreDebug_DSCSR_CDS_Pos) /*!< CoreDebug DSCSR: CDS Mask */ + +#define CoreDebug_DSCSR_SBRSEL_Pos 1U /*!< CoreDebug DSCSR: SBRSEL Position */ +#define CoreDebug_DSCSR_SBRSEL_Msk (1UL << CoreDebug_DSCSR_SBRSEL_Pos) /*!< CoreDebug DSCSR: SBRSEL Mask */ + +#define CoreDebug_DSCSR_SBRSELEN_Pos 0U /*!< CoreDebug DSCSR: SBRSELEN Position */ +#define CoreDebug_DSCSR_SBRSELEN_Msk (1UL /*<< CoreDebug_DSCSR_SBRSELEN_Pos*/) /*!< CoreDebug DSCSR: SBRSELEN Mask */ + +/*@} end of group CMSIS_CoreDebug */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_core_bitfield Core register bit field macros + \brief Macros for use with bit field definitions (xxx_Pos, xxx_Msk). + @{ + */ + +/** + \brief Mask and shift a bit field value for use in a register bit range. + \param[in] field Name of the register bit field. + \param[in] value Value of the bit field. This parameter is interpreted as an uint32_t type. + \return Masked and shifted value. +*/ +#define _VAL2FLD(field, value) (((uint32_t)(value) << field ## _Pos) & field ## _Msk) + +/** + \brief Mask and shift a register value to extract a bit filed value. + \param[in] field Name of the register bit field. + \param[in] value Value of register. This parameter is interpreted as an uint32_t type. + \return Masked and shifted bit field value. +*/ +#define _FLD2VAL(field, value) (((uint32_t)(value) & field ## _Msk) >> field ## _Pos) + +/*@} end of group CMSIS_core_bitfield */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_core_base Core Definitions + \brief Definitions for base addresses, unions, and structures. + @{ + */ + +/* Memory mapping of Core Hardware */ +#define SCS_BASE (0xE000E000UL) /*!< System Control Space Base Address */ +#define DWT_BASE (0xE0001000UL) /*!< DWT Base Address */ +#define TPI_BASE (0xE0040000UL) /*!< TPI Base Address */ +#define CoreDebug_BASE (0xE000EDF0UL) /*!< Core Debug Base Address */ +#define SysTick_BASE (SCS_BASE + 0x0010UL) /*!< SysTick Base Address */ +#define NVIC_BASE (SCS_BASE + 0x0100UL) /*!< NVIC Base Address */ +#define SCB_BASE (SCS_BASE + 0x0D00UL) /*!< System Control Block Base Address */ + + +#define SCB ((SCB_Type *) SCB_BASE ) /*!< SCB configuration struct */ +#define SysTick ((SysTick_Type *) SysTick_BASE ) /*!< SysTick configuration struct */ +#define NVIC ((NVIC_Type *) NVIC_BASE ) /*!< NVIC configuration struct */ +#define DWT ((DWT_Type *) DWT_BASE ) /*!< DWT configuration struct */ +#define TPI ((TPI_Type *) TPI_BASE ) /*!< TPI configuration struct */ +#define CoreDebug ((CoreDebug_Type *) CoreDebug_BASE ) /*!< Core Debug configuration struct */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) +#define MPU_BASE (SCS_BASE + 0x0D90UL) /*!< Memory Protection Unit */ +#define MPU ((MPU_Type *) MPU_BASE ) /*!< Memory Protection Unit */ +#endif + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +#define SAU_BASE (SCS_BASE + 0x0DD0UL) /*!< Security Attribution Unit */ +#define SAU ((SAU_Type *) SAU_BASE ) /*!< Security Attribution Unit */ +#endif + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +#define SCS_BASE_NS (0xE002E000UL) /*!< System Control Space Base Address (non-secure address space) */ +#define CoreDebug_BASE_NS (0xE002EDF0UL) /*!< Core Debug Base Address (non-secure address space) */ +#define SysTick_BASE_NS (SCS_BASE_NS + 0x0010UL) /*!< SysTick Base Address (non-secure address space) */ +#define NVIC_BASE_NS (SCS_BASE_NS + 0x0100UL) /*!< NVIC Base Address (non-secure address space) */ +#define SCB_BASE_NS (SCS_BASE_NS + 0x0D00UL) /*!< System Control Block Base Address (non-secure address space) */ + +#define SCB_NS ((SCB_Type *) SCB_BASE_NS ) /*!< SCB configuration struct (non-secure address space) */ +#define SysTick_NS ((SysTick_Type *) SysTick_BASE_NS ) /*!< SysTick configuration struct (non-secure address space) */ +#define NVIC_NS ((NVIC_Type *) NVIC_BASE_NS ) /*!< NVIC configuration struct (non-secure address space) */ +#define CoreDebug_NS ((CoreDebug_Type *) CoreDebug_BASE_NS) /*!< Core Debug configuration struct (non-secure address space) */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) +#define MPU_BASE_NS (SCS_BASE_NS + 0x0D90UL) /*!< Memory Protection Unit (non-secure address space) */ +#define MPU_NS ((MPU_Type *) MPU_BASE_NS ) /*!< Memory Protection Unit (non-secure address space) */ +#endif + +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ +/*@} */ + + + +/******************************************************************************* + * Hardware Abstraction Layer + Core Function Interface contains: + - Core NVIC Functions + - Core SysTick Functions + - Core Register Access Functions + ******************************************************************************/ +/** + \defgroup CMSIS_Core_FunctionInterface Functions and Instructions Reference +*/ + + + +/* ########################## NVIC functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_NVICFunctions NVIC Functions + \brief Functions that manage interrupts and exceptions via the NVIC. + @{ + */ + +#ifdef CMSIS_NVIC_VIRTUAL +#ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE +#define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h" +#endif +#include CMSIS_NVIC_VIRTUAL_HEADER_FILE +#else +/*#define NVIC_SetPriorityGrouping __NVIC_SetPriorityGrouping not available for Cortex-M23 */ +/*#define NVIC_GetPriorityGrouping __NVIC_GetPriorityGrouping not available for Cortex-M23 */ +#define NVIC_EnableIRQ __NVIC_EnableIRQ +#define NVIC_GetEnableIRQ __NVIC_GetEnableIRQ +#define NVIC_DisableIRQ __NVIC_DisableIRQ +#define NVIC_GetPendingIRQ __NVIC_GetPendingIRQ +#define NVIC_SetPendingIRQ __NVIC_SetPendingIRQ +#define NVIC_ClearPendingIRQ __NVIC_ClearPendingIRQ +#define NVIC_GetActive __NVIC_GetActive +#define NVIC_SetPriority __NVIC_SetPriority +#define NVIC_GetPriority __NVIC_GetPriority +#define NVIC_SystemReset __NVIC_SystemReset +#endif /* CMSIS_NVIC_VIRTUAL */ + +#ifdef CMSIS_VECTAB_VIRTUAL +#ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h" +#endif +#include CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetVector __NVIC_SetVector +#define NVIC_GetVector __NVIC_GetVector +#endif /* (CMSIS_VECTAB_VIRTUAL) */ + +#define NVIC_USER_IRQ_OFFSET 16 + + +/* Special LR values for Secure/Non-Secure call handling and exception handling */ + +/* Function Return Payload (from ARMv8-M Architecture Reference Manual) LR value on entry from Secure BLXNS */ +#define FNC_RETURN (0xFEFFFFFFUL) /* bit [0] ignored when processing a branch */ + +/* The following EXC_RETURN mask values are used to evaluate the LR on exception entry */ +#define EXC_RETURN_PREFIX (0xFF000000UL) /* bits [31:24] set to indicate an EXC_RETURN value */ +#define EXC_RETURN_S (0x00000040UL) /* bit [6] stack used to push registers: 0=Non-secure 1=Secure */ +#define EXC_RETURN_DCRS (0x00000020UL) /* bit [5] stacking rules for called registers: 0=skipped 1=saved */ +#define EXC_RETURN_FTYPE (0x00000010UL) /* bit [4] allocate stack for floating-point context: 0=done 1=skipped */ +#define EXC_RETURN_MODE (0x00000008UL) /* bit [3] processor mode for return: 0=Handler mode 1=Thread mode */ +#define EXC_RETURN_SPSEL (0x00000002UL) /* bit [1] stack pointer used to restore context: 0=MSP 1=PSP */ +#define EXC_RETURN_ES (0x00000001UL) /* bit [0] security state exception was taken to: 0=Non-secure 1=Secure */ + +/* Integrity Signature (from ARMv8-M Architecture Reference Manual) for exception context stacking */ +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) /* Value for processors with floating-point extension: */ +#define EXC_INTEGRITY_SIGNATURE (0xFEFA125AUL) /* bit [0] SFTC must match LR bit[4] EXC_RETURN_FTYPE */ +#else +#define EXC_INTEGRITY_SIGNATURE (0xFEFA125BUL) /* Value for processors without floating-point extension */ +#endif + + +/* Interrupt Priorities are WORD accessible only under Armv6-M */ +/* The following MACROS handle generation of the register offset and byte masks */ +#define _BIT_SHIFT(IRQn) ( ((((uint32_t)(int32_t)(IRQn)) ) & 0x03UL) * 8UL) +#define _SHP_IDX(IRQn) ( (((((uint32_t)(int32_t)(IRQn)) & 0x0FUL)-8UL) >> 2UL) ) +#define _IP_IDX(IRQn) ( (((uint32_t)(int32_t)(IRQn)) >> 2UL) ) + +#define __NVIC_SetPriorityGrouping(X) (void)(X) +#define __NVIC_GetPriorityGrouping() (0U) + +/** + \brief Enable Interrupt + \details Enables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Interrupt Enable status + \details Returns a device specific interrupt enable status from the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Disable Interrupt + \details Disables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + __DSB(); + __ISB(); + } +} + + +/** + \brief Get Pending Interrupt + \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not pending. + \return 1 Interrupt status is pending. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Pending Interrupt + \details Sets the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Clear Pending Interrupt + \details Clears the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Active Interrupt + \details Reads the active register in the NVIC and returns the active bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not active. + \return 1 Interrupt status is active. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetActive(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->IABR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \brief Get Interrupt Target State + \details Reads the interrupt target field in the NVIC and returns the interrupt target bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 if interrupt is assigned to Secure + \return 1 if interrupt is assigned to Non Secure + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t NVIC_GetTargetState(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Interrupt Target State + \details Sets the interrupt target field in the NVIC and returns the interrupt target bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 if interrupt is assigned to Secure + 1 if interrupt is assigned to Non Secure + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t NVIC_SetTargetState(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] |= ((uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL))); + return ((uint32_t)(((NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Clear Interrupt Target State + \details Clears the interrupt target field in the NVIC and returns the interrupt target bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 if interrupt is assigned to Secure + 1 if interrupt is assigned to Non Secure + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t NVIC_ClearTargetState(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] &= ~((uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL))); + return ((uint32_t)(((NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + + +/** + \brief Set Interrupt Priority + \details Sets the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \param [in] priority Priority to set. + \note The priority cannot be set for every processor exception. + */ +__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->IPR[_IP_IDX(IRQn)] = ((uint32_t)(NVIC->IPR[_IP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); + } + else + { + SCB->SHPR[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHPR[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); + } +} + + +/** + \brief Get Interrupt Priority + \details Reads the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Interrupt Priority. + Value is aligned automatically to the implemented priority bits of the microcontroller. + */ +__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn) +{ + + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->IPR[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + } + else + { + return ((uint32_t)(((SCB->SHPR[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + } +} + + +/** + \brief Encode Priority + \details Encodes the priority for an interrupt with the given priority group, + preemptive priority value, and subpriority value. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set. + \param [in] PriorityGroup Used priority group. + \param [in] PreemptPriority Preemptive priority value (starting from 0). + \param [in] SubPriority Subpriority value (starting from 0). + \return Encoded priority. Value can be used in the function \ref NVIC_SetPriority(). + */ +__STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority) +{ + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + uint32_t PreemptPriorityBits; + uint32_t SubPriorityBits; + + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); + SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + + return ( + ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) | + ((SubPriority & (uint32_t)((1UL << (SubPriorityBits )) - 1UL))) + ); +} + + +/** + \brief Decode Priority + \details Decodes an interrupt priority value with a given priority group to + preemptive priority value and subpriority value. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set. + \param [in] Priority Priority value, which can be retrieved with the function \ref NVIC_GetPriority(). + \param [in] PriorityGroup Used priority group. + \param [out] pPreemptPriority Preemptive priority value (starting from 0). + \param [out] pSubPriority Subpriority value (starting from 0). + */ +__STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* const pPreemptPriority, uint32_t* const pSubPriority) +{ + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + uint32_t PreemptPriorityBits; + uint32_t SubPriorityBits; + + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); + SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + + *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL); + *pSubPriority = (Priority ) & (uint32_t)((1UL << (SubPriorityBits )) - 1UL); +} + + +/** + \brief Set Interrupt Vector + \details Sets an interrupt vector in SRAM based interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + VTOR must been relocated to SRAM before. + If VTOR is not present address 0 must be mapped to SRAM. + \param [in] IRQn Interrupt number + \param [in] vector Address of interrupt handler function + */ +__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector) +{ +#if defined (__VTOR_PRESENT) && (__VTOR_PRESENT == 1U) + uint32_t* vectors = (uint32_t*)SCB->VTOR; +#else + uint32_t* vectors = (uint32_t*)0x0U; +#endif + vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector; +} + + +/** + \brief Get Interrupt Vector + \details Reads an interrupt vector from interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Address of interrupt handler function + */ +__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn) +{ +#if defined (__VTOR_PRESENT) && (__VTOR_PRESENT == 1U) + uint32_t* vectors = (uint32_t*)SCB->VTOR; +#else + uint32_t* vectors = (uint32_t*)0x0U; +#endif + return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET]; +} + + +/** + \brief System Reset + \details Initiates a system reset request to reset the MCU. + */ +__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void) +{ + __DSB(); /* Ensure all outstanding memory accesses included + buffered write are completed before reset */ + SCB->AIRCR = ((0x5FAUL << SCB_AIRCR_VECTKEY_Pos) | + SCB_AIRCR_SYSRESETREQ_Msk); + __DSB(); /* Ensure completion of memory access */ + + for (;;) /* wait until reset */ + { + __NOP(); + } +} + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \brief Enable Interrupt (non-secure) + \details Enables a device specific interrupt in the non-secure NVIC interrupt controller when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_EnableIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ISER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Interrupt Enable status (non-secure) + \details Returns a device specific interrupt enable status from the non-secure NVIC interrupt controller when in secure state. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetEnableIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC_NS->ISER[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Disable Interrupt (non-secure) + \details Disables a device specific interrupt in the non-secure NVIC interrupt controller when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_DisableIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ICER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Pending Interrupt (non-secure) + \details Reads the NVIC pending register in the non-secure NVIC when in secure state and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not pending. + \return 1 Interrupt status is pending. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetPendingIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC_NS->ISPR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Pending Interrupt (non-secure) + \details Sets the pending bit of a device specific interrupt in the non-secure NVIC pending register when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_SetPendingIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ISPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Clear Pending Interrupt (non-secure) + \details Clears the pending bit of a device specific interrupt in the non-secure NVIC pending register when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_ClearPendingIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ICPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Active Interrupt (non-secure) + \details Reads the active register in non-secure NVIC when in secure state and returns the active bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not active. + \return 1 Interrupt status is active. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetActive_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC_NS->IABR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Interrupt Priority (non-secure) + \details Sets the priority of a non-secure device specific interrupt or a non-secure processor exception when in secure state. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \param [in] priority Priority to set. + \note The priority cannot be set for every non-secure processor exception. + */ +__STATIC_INLINE void TZ_NVIC_SetPriority_NS(IRQn_Type IRQn, uint32_t priority) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->IPR[_IP_IDX(IRQn)] = ((uint32_t)(NVIC_NS->IPR[_IP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); + } + else + { + SCB_NS->SHPR[_SHP_IDX(IRQn)] = ((uint32_t)(SCB_NS->SHPR[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); + } +} + + +/** + \brief Get Interrupt Priority (non-secure) + \details Reads the priority of a non-secure device specific interrupt or a non-secure processor exception when in secure state. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Interrupt Priority. Value is aligned automatically to the implemented priority bits of the microcontroller. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetPriority_NS(IRQn_Type IRQn) +{ + + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC_NS->IPR[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + } + else + { + return ((uint32_t)(((SCB_NS->SHPR[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + } +} +#endif /* defined (__ARM_FEATURE_CMSE) &&(__ARM_FEATURE_CMSE == 3U) */ + +/*@} end of CMSIS_Core_NVICFunctions */ + +/* ########################## MPU functions #################################### */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) + +#include "mpu_armv8.h" + +#endif + +/* ########################## FPU functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_FpuFunctions FPU Functions + \brief Function that provides FPU type. + @{ + */ + +/** + \brief get FPU type + \details returns the FPU type + \returns + - \b 0: No FPU + - \b 1: Single precision FPU + - \b 2: Double + Single precision FPU + */ +__STATIC_INLINE uint32_t SCB_GetFPUType(void) +{ + return 0U; /* No FPU */ +} + + +/*@} end of CMSIS_Core_FpuFunctions */ + + + +/* ########################## SAU functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_SAUFunctions SAU Functions + \brief Functions that configure the SAU. + @{ + */ + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) + +/** + \brief Enable SAU + \details Enables the Security Attribution Unit (SAU). + */ +__STATIC_INLINE void TZ_SAU_Enable(void) +{ + SAU->CTRL |= (SAU_CTRL_ENABLE_Msk); +} + + + +/** + \brief Disable SAU + \details Disables the Security Attribution Unit (SAU). + */ +__STATIC_INLINE void TZ_SAU_Disable(void) +{ + SAU->CTRL &= ~(SAU_CTRL_ENABLE_Msk); +} + +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + +/*@} end of CMSIS_Core_SAUFunctions */ + + + + +/* ################################## SysTick function ############################################ */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_SysTickFunctions SysTick Functions + \brief Functions that configure the System. + @{ + */ + +#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U) + +/** + \brief System Tick Configuration + \details Initializes the System Timer and its interrupt, and starts the System Tick Timer. + Counter is in free running mode to generate periodic interrupts. + \param [in] ticks Number of ticks between two interrupts. + \return 0 Function succeeded. + \return 1 Function failed. + \note When the variable __Vendor_SysTickConfig is set to 1, then the + function SysTick_Config is not included. In this case, the file device.h + must contain a vendor-specific implementation of this function. + */ +__STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks) +{ + if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk) + { + return (1UL); /* Reload value impossible */ + } + + SysTick->LOAD = (uint32_t)(ticks - 1UL); /* set reload register */ + NVIC_SetPriority (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */ + SysTick->VAL = 0UL; /* Load the SysTick Counter Value */ + SysTick->CTRL = SysTick_CTRL_CLKSOURCE_Msk | + SysTick_CTRL_TICKINT_Msk | + SysTick_CTRL_ENABLE_Msk; /* Enable SysTick IRQ and SysTick Timer */ + return (0UL); /* Function successful */ +} + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \brief System Tick Configuration (non-secure) + \details Initializes the non-secure System Timer and its interrupt when in secure state, and starts the System Tick Timer. + Counter is in free running mode to generate periodic interrupts. + \param [in] ticks Number of ticks between two interrupts. + \return 0 Function succeeded. + \return 1 Function failed. + \note When the variable __Vendor_SysTickConfig is set to 1, then the + function TZ_SysTick_Config_NS is not included. In this case, the file device.h + must contain a vendor-specific implementation of this function. + + */ +__STATIC_INLINE uint32_t TZ_SysTick_Config_NS(uint32_t ticks) +{ + if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk) + { + return (1UL); /* Reload value impossible */ + } + + SysTick_NS->LOAD = (uint32_t)(ticks - 1UL); /* set reload register */ + TZ_NVIC_SetPriority_NS (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */ + SysTick_NS->VAL = 0UL; /* Load the SysTick Counter Value */ + SysTick_NS->CTRL = SysTick_CTRL_CLKSOURCE_Msk | + SysTick_CTRL_TICKINT_Msk | + SysTick_CTRL_ENABLE_Msk; /* Enable SysTick IRQ and SysTick Timer */ + return (0UL); /* Function successful */ +} +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + +#endif + +/*@} end of CMSIS_Core_SysTickFunctions */ + + + + +#ifdef __cplusplus +} +#endif + +#endif /* __CORE_CM23_H_DEPENDANT */ + +#endif /* __CMSIS_GENERIC */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/core_cm3.h b/EpsilonLights/Drivers/CMSIS/Include/core_cm3.h index df961b12..356db145 100644 --- a/EpsilonLights/Drivers/CMSIS/Include/core_cm3.h +++ b/EpsilonLights/Drivers/CMSIS/Include/core_cm3.h @@ -1,40 +1,30 @@ /**************************************************************************//** * @file core_cm3.h * @brief CMSIS Cortex-M3 Core Peripheral Access Layer Header File - * @version V4.30 - * @date 20. October 2015 + * @version V5.0.8 + * @date 04. June 2018 ******************************************************************************/ -/* Copyright (c) 2009 - 2015 ARM LIMITED - - All rights reserved. - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - - Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - - Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - Neither the name of ARM nor the names of its contributors may be used - to endorse or promote products derived from this software without - specific prior written permission. - * - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE - LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR - CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF - SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS - INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN - CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) - ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE - POSSIBILITY OF SUCH DAMAGE. - ---------------------------------------------------------------------------*/ - +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ #if defined ( __ICCARM__ ) #pragma system_include /* treat file as system include file for MISRA check */ -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#elif defined (__clang__) #pragma clang system_header /* treat file as system include file */ #endif @@ -70,53 +60,15 @@ extern "C" { @{ */ +#include "cmsis_version.h" + /* CMSIS CM3 definitions */ -#define __CM3_CMSIS_VERSION_MAIN (0x04U) /*!< [31:16] CMSIS HAL main version */ -#define __CM3_CMSIS_VERSION_SUB (0x1EU) /*!< [15:0] CMSIS HAL sub version */ +#define __CM3_CMSIS_VERSION_MAIN (__CM_CMSIS_VERSION_MAIN) /*!< \deprecated [31:16] CMSIS HAL main version */ +#define __CM3_CMSIS_VERSION_SUB (__CM_CMSIS_VERSION_SUB) /*!< \deprecated [15:0] CMSIS HAL sub version */ #define __CM3_CMSIS_VERSION ((__CM3_CMSIS_VERSION_MAIN << 16U) | \ - __CM3_CMSIS_VERSION_SUB ) /*!< CMSIS HAL version number */ - -#define __CORTEX_M (0x03U) /*!< Cortex-M Core */ - - -#if defined ( __CC_ARM ) -#define __ASM __asm /*!< asm keyword for ARM Compiler */ -#define __INLINE __inline /*!< inline keyword for ARM Compiler */ -#define __STATIC_INLINE static __inline - -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) -#define __ASM __asm /*!< asm keyword for ARM Compiler */ -#define __INLINE __inline /*!< inline keyword for ARM Compiler */ -#define __STATIC_INLINE static __inline - -#elif defined ( __GNUC__ ) -#define __ASM __asm /*!< asm keyword for GNU Compiler */ -#define __INLINE inline /*!< inline keyword for GNU Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __ICCARM__ ) -#define __ASM __asm /*!< asm keyword for IAR Compiler */ -#define __INLINE inline /*!< inline keyword for IAR Compiler. Only available in High optimization mode! */ -#define __STATIC_INLINE static inline - -#elif defined ( __TMS470__ ) -#define __ASM __asm /*!< asm keyword for TI CCS Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __TASKING__ ) -#define __ASM __asm /*!< asm keyword for TASKING Compiler */ -#define __INLINE inline /*!< inline keyword for TASKING Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __CSMC__ ) -#define __packed -#define __ASM _asm /*!< asm keyword for COSMIC Compiler */ -#define __INLINE inline /*!< inline keyword for COSMIC Compiler. Use -pc99 on compile line */ -#define __STATIC_INLINE static inline + __CM3_CMSIS_VERSION_SUB ) /*!< \deprecated CMSIS HAL version number */ -#else -#error Unknown compiler -#endif +#define __CORTEX_M (3U) /*!< Cortex-M Core */ /** __FPU_USED indicates whether an FPU is used or not. This core does not support an FPU at all @@ -128,7 +80,7 @@ extern "C" { #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) #if defined __ARM_PCS_VFP #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif @@ -143,7 +95,7 @@ extern "C" { #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif -#elif defined ( __TMS470__ ) +#elif defined ( __TI_ARM__ ) #if defined __TI_VFP_SUPPORT__ #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif @@ -160,8 +112,8 @@ extern "C" { #endif -#include "core_cmInstr.h" /* Core Instruction Access */ -#include "core_cmFunc.h" /* Core Function Access */ +#include "cmsis_compiler.h" /* CMSIS compiler specific defines */ + #ifdef __cplusplus } @@ -191,7 +143,7 @@ extern "C" { #endif #ifndef __NVIC_PRIO_BITS -#define __NVIC_PRIO_BITS 4U +#define __NVIC_PRIO_BITS 3U #warning "__NVIC_PRIO_BITS not defined in device header file; using default!" #endif @@ -308,9 +260,11 @@ typedef union struct { uint32_t ISR: 9; /*!< bit: 0.. 8 Exception number */ - uint32_t _reserved0: 15; /*!< bit: 9..23 Reserved */ - uint32_t T: 1; /*!< bit: 24 Thumb bit (read 0) */ - uint32_t IT: 2; /*!< bit: 25..26 saved IT state (read 0) */ + uint32_t _reserved0: 1; /*!< bit: 9 Reserved */ + uint32_t ICI_IT_1: 6; /*!< bit: 10..15 ICI/IT part 1 */ + uint32_t _reserved1: 8; /*!< bit: 16..23 Reserved */ + uint32_t T: 1; /*!< bit: 24 Thumb bit */ + uint32_t ICI_IT_2: 2; /*!< bit: 25..26 ICI/IT part 2 */ uint32_t Q: 1; /*!< bit: 27 Saturation condition flag */ uint32_t V: 1; /*!< bit: 28 Overflow condition code flag */ uint32_t C: 1; /*!< bit: 29 Carry condition code flag */ @@ -336,12 +290,15 @@ typedef union #define xPSR_Q_Pos 27U /*!< xPSR: Q Position */ #define xPSR_Q_Msk (1UL << xPSR_Q_Pos) /*!< xPSR: Q Mask */ -#define xPSR_IT_Pos 25U /*!< xPSR: IT Position */ -#define xPSR_IT_Msk (3UL << xPSR_IT_Pos) /*!< xPSR: IT Mask */ +#define xPSR_ICI_IT_2_Pos 25U /*!< xPSR: ICI/IT part 2 Position */ +#define xPSR_ICI_IT_2_Msk (3UL << xPSR_ICI_IT_2_Pos) /*!< xPSR: ICI/IT part 2 Mask */ #define xPSR_T_Pos 24U /*!< xPSR: T Position */ #define xPSR_T_Msk (1UL << xPSR_T_Pos) /*!< xPSR: T Mask */ +#define xPSR_ICI_IT_1_Pos 10U /*!< xPSR: ICI/IT part 1 Position */ +#define xPSR_ICI_IT_1_Msk (0x3FUL << xPSR_ICI_IT_1_Pos) /*!< xPSR: ICI/IT part 1 Mask */ + #define xPSR_ISR_Pos 0U /*!< xPSR: ISR Position */ #define xPSR_ISR_Msk (0x1FFUL /*<< xPSR_ISR_Pos*/) /*!< xPSR: ISR Mask */ @@ -487,7 +444,7 @@ typedef struct #define SCB_ICSR_VECTACTIVE_Msk (0x1FFUL /*<< SCB_ICSR_VECTACTIVE_Pos*/) /*!< SCB ICSR: VECTACTIVE Mask */ /* SCB Vector Table Offset Register Definitions */ -#if (__CM3_REV < 0x0201U) /* core r2p1 */ +#if defined (__CM3_REV) && (__CM3_REV < 0x0201U) /* core r2p1 */ #define SCB_VTOR_TBLBASE_Pos 29U /*!< SCB VTOR: TBLBASE Position */ #define SCB_VTOR_TBLBASE_Msk (1UL << SCB_VTOR_TBLBASE_Pos) /*!< SCB VTOR: TBLBASE Mask */ @@ -602,6 +559,60 @@ typedef struct #define SCB_CFSR_MEMFAULTSR_Pos 0U /*!< SCB CFSR: Memory Manage Fault Status Register Position */ #define SCB_CFSR_MEMFAULTSR_Msk (0xFFUL /*<< SCB_CFSR_MEMFAULTSR_Pos*/) /*!< SCB CFSR: Memory Manage Fault Status Register Mask */ +/* MemManage Fault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_MMARVALID_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 7U) /*!< SCB CFSR (MMFSR): MMARVALID Position */ +#define SCB_CFSR_MMARVALID_Msk (1UL << SCB_CFSR_MMARVALID_Pos) /*!< SCB CFSR (MMFSR): MMARVALID Mask */ + +#define SCB_CFSR_MSTKERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 4U) /*!< SCB CFSR (MMFSR): MSTKERR Position */ +#define SCB_CFSR_MSTKERR_Msk (1UL << SCB_CFSR_MSTKERR_Pos) /*!< SCB CFSR (MMFSR): MSTKERR Mask */ + +#define SCB_CFSR_MUNSTKERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 3U) /*!< SCB CFSR (MMFSR): MUNSTKERR Position */ +#define SCB_CFSR_MUNSTKERR_Msk (1UL << SCB_CFSR_MUNSTKERR_Pos) /*!< SCB CFSR (MMFSR): MUNSTKERR Mask */ + +#define SCB_CFSR_DACCVIOL_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 1U) /*!< SCB CFSR (MMFSR): DACCVIOL Position */ +#define SCB_CFSR_DACCVIOL_Msk (1UL << SCB_CFSR_DACCVIOL_Pos) /*!< SCB CFSR (MMFSR): DACCVIOL Mask */ + +#define SCB_CFSR_IACCVIOL_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 0U) /*!< SCB CFSR (MMFSR): IACCVIOL Position */ +#define SCB_CFSR_IACCVIOL_Msk (1UL /*<< SCB_CFSR_IACCVIOL_Pos*/) /*!< SCB CFSR (MMFSR): IACCVIOL Mask */ + +/* BusFault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_BFARVALID_Pos (SCB_CFSR_BUSFAULTSR_Pos + 7U) /*!< SCB CFSR (BFSR): BFARVALID Position */ +#define SCB_CFSR_BFARVALID_Msk (1UL << SCB_CFSR_BFARVALID_Pos) /*!< SCB CFSR (BFSR): BFARVALID Mask */ + +#define SCB_CFSR_STKERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 4U) /*!< SCB CFSR (BFSR): STKERR Position */ +#define SCB_CFSR_STKERR_Msk (1UL << SCB_CFSR_STKERR_Pos) /*!< SCB CFSR (BFSR): STKERR Mask */ + +#define SCB_CFSR_UNSTKERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 3U) /*!< SCB CFSR (BFSR): UNSTKERR Position */ +#define SCB_CFSR_UNSTKERR_Msk (1UL << SCB_CFSR_UNSTKERR_Pos) /*!< SCB CFSR (BFSR): UNSTKERR Mask */ + +#define SCB_CFSR_IMPRECISERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 2U) /*!< SCB CFSR (BFSR): IMPRECISERR Position */ +#define SCB_CFSR_IMPRECISERR_Msk (1UL << SCB_CFSR_IMPRECISERR_Pos) /*!< SCB CFSR (BFSR): IMPRECISERR Mask */ + +#define SCB_CFSR_PRECISERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 1U) /*!< SCB CFSR (BFSR): PRECISERR Position */ +#define SCB_CFSR_PRECISERR_Msk (1UL << SCB_CFSR_PRECISERR_Pos) /*!< SCB CFSR (BFSR): PRECISERR Mask */ + +#define SCB_CFSR_IBUSERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 0U) /*!< SCB CFSR (BFSR): IBUSERR Position */ +#define SCB_CFSR_IBUSERR_Msk (1UL << SCB_CFSR_IBUSERR_Pos) /*!< SCB CFSR (BFSR): IBUSERR Mask */ + +/* UsageFault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_DIVBYZERO_Pos (SCB_CFSR_USGFAULTSR_Pos + 9U) /*!< SCB CFSR (UFSR): DIVBYZERO Position */ +#define SCB_CFSR_DIVBYZERO_Msk (1UL << SCB_CFSR_DIVBYZERO_Pos) /*!< SCB CFSR (UFSR): DIVBYZERO Mask */ + +#define SCB_CFSR_UNALIGNED_Pos (SCB_CFSR_USGFAULTSR_Pos + 8U) /*!< SCB CFSR (UFSR): UNALIGNED Position */ +#define SCB_CFSR_UNALIGNED_Msk (1UL << SCB_CFSR_UNALIGNED_Pos) /*!< SCB CFSR (UFSR): UNALIGNED Mask */ + +#define SCB_CFSR_NOCP_Pos (SCB_CFSR_USGFAULTSR_Pos + 3U) /*!< SCB CFSR (UFSR): NOCP Position */ +#define SCB_CFSR_NOCP_Msk (1UL << SCB_CFSR_NOCP_Pos) /*!< SCB CFSR (UFSR): NOCP Mask */ + +#define SCB_CFSR_INVPC_Pos (SCB_CFSR_USGFAULTSR_Pos + 2U) /*!< SCB CFSR (UFSR): INVPC Position */ +#define SCB_CFSR_INVPC_Msk (1UL << SCB_CFSR_INVPC_Pos) /*!< SCB CFSR (UFSR): INVPC Mask */ + +#define SCB_CFSR_INVSTATE_Pos (SCB_CFSR_USGFAULTSR_Pos + 1U) /*!< SCB CFSR (UFSR): INVSTATE Position */ +#define SCB_CFSR_INVSTATE_Msk (1UL << SCB_CFSR_INVSTATE_Pos) /*!< SCB CFSR (UFSR): INVSTATE Mask */ + +#define SCB_CFSR_UNDEFINSTR_Pos (SCB_CFSR_USGFAULTSR_Pos + 0U) /*!< SCB CFSR (UFSR): UNDEFINSTR Position */ +#define SCB_CFSR_UNDEFINSTR_Msk (1UL << SCB_CFSR_UNDEFINSTR_Pos) /*!< SCB CFSR (UFSR): UNDEFINSTR Mask */ + /* SCB Hard Fault Status Register Definitions */ #define SCB_HFSR_DEBUGEVT_Pos 31U /*!< SCB HFSR: DEBUGEVT Position */ #define SCB_HFSR_DEBUGEVT_Msk (1UL << SCB_HFSR_DEBUGEVT_Pos) /*!< SCB HFSR: DEBUGEVT Mask */ @@ -645,7 +656,7 @@ typedef struct { uint32_t RESERVED0[1U]; __IM uint32_t ICTR; /*!< Offset: 0x004 (R/ ) Interrupt Controller Type Register */ -#if ((defined __CM3_REV) && (__CM3_REV >= 0x200U)) +#if defined (__CM3_REV) && (__CM3_REV >= 0x200U) __IOM uint32_t ACTLR; /*!< Offset: 0x008 (R/W) Auxiliary Control Register */ #else uint32_t RESERVED1[1U]; @@ -770,7 +781,7 @@ typedef struct /* ITM Trace Privilege Register Definitions */ #define ITM_TPR_PRIVMASK_Pos 0U /*!< ITM TPR: PRIVMASK Position */ -#define ITM_TPR_PRIVMASK_Msk (0xFUL /*<< ITM_TPR_PRIVMASK_Pos*/) /*!< ITM TPR: PRIVMASK Mask */ +#define ITM_TPR_PRIVMASK_Msk (0xFFFFFFFFUL /*<< ITM_TPR_PRIVMASK_Pos*/) /*!< ITM TPR: PRIVMASK Mask */ /* ITM Trace Control Register Definitions */ #define ITM_TCR_BUSY_Pos 23U /*!< ITM TCR: BUSY Position */ @@ -984,7 +995,7 @@ typedef struct */ typedef struct { - __IOM uint32_t SSPSR; /*!< Offset: 0x000 (R/ ) Supported Parallel Port Size Register */ + __IM uint32_t SSPSR; /*!< Offset: 0x000 (R/ ) Supported Parallel Port Size Register */ __IOM uint32_t CSPSR; /*!< Offset: 0x004 (R/W) Current Parallel Port Size Register */ uint32_t RESERVED0[2U]; __IOM uint32_t ACPR; /*!< Offset: 0x010 (R/W) Asynchronous Clock Prescaler Register */ @@ -995,7 +1006,7 @@ typedef struct __IOM uint32_t FFCR; /*!< Offset: 0x304 (R/W) Formatter and Flush Control Register */ __IM uint32_t FSCR; /*!< Offset: 0x308 (R/ ) Formatter Synchronization Counter Register */ uint32_t RESERVED3[759U]; - __IM uint32_t TRIGGER; /*!< Offset: 0xEE8 (R/ ) TRIGGER */ + __IM uint32_t TRIGGER; /*!< Offset: 0xEE8 (R/ ) TRIGGER Register */ __IM uint32_t FIFO0; /*!< Offset: 0xEEC (R/ ) Integration ETM Data */ __IM uint32_t ITATBCTR2; /*!< Offset: 0xEF0 (R/ ) ITATBCTR2 */ uint32_t RESERVED4[1U]; @@ -1065,8 +1076,11 @@ typedef struct #define TPI_FIFO0_ETM0_Msk (0xFFUL /*<< TPI_FIFO0_ETM0_Pos*/) /*!< TPI FIFO0: ETM0 Mask */ /* TPI ITATBCTR2 Register Definitions */ -#define TPI_ITATBCTR2_ATREADY_Pos 0U /*!< TPI ITATBCTR2: ATREADY Position */ -#define TPI_ITATBCTR2_ATREADY_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY_Pos*/) /*!< TPI ITATBCTR2: ATREADY Mask */ +#define TPI_ITATBCTR2_ATREADY2_Pos 0U /*!< TPI ITATBCTR2: ATREADY2 Position */ +#define TPI_ITATBCTR2_ATREADY2_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY2_Pos*/) /*!< TPI ITATBCTR2: ATREADY2 Mask */ + +#define TPI_ITATBCTR2_ATREADY1_Pos 0U /*!< TPI ITATBCTR2: ATREADY1 Position */ +#define TPI_ITATBCTR2_ATREADY1_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY1_Pos*/) /*!< TPI ITATBCTR2: ATREADY1 Mask */ /* TPI Integration ITM Data Register Definitions (FIFO1) */ #define TPI_FIFO1_ITM_ATVALID_Pos 29U /*!< TPI FIFO1: ITM_ATVALID Position */ @@ -1091,12 +1105,15 @@ typedef struct #define TPI_FIFO1_ITM0_Msk (0xFFUL /*<< TPI_FIFO1_ITM0_Pos*/) /*!< TPI FIFO1: ITM0 Mask */ /* TPI ITATBCTR0 Register Definitions */ -#define TPI_ITATBCTR0_ATREADY_Pos 0U /*!< TPI ITATBCTR0: ATREADY Position */ -#define TPI_ITATBCTR0_ATREADY_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY_Pos*/) /*!< TPI ITATBCTR0: ATREADY Mask */ +#define TPI_ITATBCTR0_ATREADY2_Pos 0U /*!< TPI ITATBCTR0: ATREADY2 Position */ +#define TPI_ITATBCTR0_ATREADY2_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY2_Pos*/) /*!< TPI ITATBCTR0: ATREADY2 Mask */ + +#define TPI_ITATBCTR0_ATREADY1_Pos 0U /*!< TPI ITATBCTR0: ATREADY1 Position */ +#define TPI_ITATBCTR0_ATREADY1_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY1_Pos*/) /*!< TPI ITATBCTR0: ATREADY1 Mask */ /* TPI Integration Mode Control Register Definitions */ #define TPI_ITCTRL_Mode_Pos 0U /*!< TPI ITCTRL: Mode Position */ -#define TPI_ITCTRL_Mode_Msk (0x1UL /*<< TPI_ITCTRL_Mode_Pos*/) /*!< TPI ITCTRL: Mode Mask */ +#define TPI_ITCTRL_Mode_Msk (0x3UL /*<< TPI_ITCTRL_Mode_Pos*/) /*!< TPI ITCTRL: Mode Mask */ /* TPI DEVID Register Definitions */ #define TPI_DEVID_NRZVALID_Pos 11U /*!< TPI DEVID: NRZVALID Position */ @@ -1118,16 +1135,16 @@ typedef struct #define TPI_DEVID_NrTraceInput_Msk (0x1FUL /*<< TPI_DEVID_NrTraceInput_Pos*/) /*!< TPI DEVID: NrTraceInput Mask */ /* TPI DEVTYPE Register Definitions */ -#define TPI_DEVTYPE_MajorType_Pos 4U /*!< TPI DEVTYPE: MajorType Position */ -#define TPI_DEVTYPE_MajorType_Msk (0xFUL << TPI_DEVTYPE_MajorType_Pos) /*!< TPI DEVTYPE: MajorType Mask */ - -#define TPI_DEVTYPE_SubType_Pos 0U /*!< TPI DEVTYPE: SubType Position */ +#define TPI_DEVTYPE_SubType_Pos 4U /*!< TPI DEVTYPE: SubType Position */ #define TPI_DEVTYPE_SubType_Msk (0xFUL /*<< TPI_DEVTYPE_SubType_Pos*/) /*!< TPI DEVTYPE: SubType Mask */ +#define TPI_DEVTYPE_MajorType_Pos 0U /*!< TPI DEVTYPE: MajorType Position */ +#define TPI_DEVTYPE_MajorType_Msk (0xFUL << TPI_DEVTYPE_MajorType_Pos) /*!< TPI DEVTYPE: MajorType Mask */ + /*@}*/ /* end of group CMSIS_TPI */ -#if (__MPU_PRESENT == 1U) +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) /** \ingroup CMSIS_core_register \defgroup CMSIS_MPU Memory Protection Unit (MPU) @@ -1153,6 +1170,8 @@ typedef struct __IOM uint32_t RASR_A3; /*!< Offset: 0x028 (R/W) MPU Alias 3 Region Attribute and Size Register */ } MPU_Type; +#define MPU_TYPE_RALIASES 4U + /* MPU Type Register Definitions */ #define MPU_TYPE_IREGION_Pos 16U /*!< MPU TYPE: IREGION Position */ #define MPU_TYPE_IREGION_Msk (0xFFUL << MPU_TYPE_IREGION_Pos) /*!< MPU TYPE: IREGION Mask */ @@ -1337,18 +1356,18 @@ typedef struct /** \brief Mask and shift a bit field value for use in a register bit range. \param[in] field Name of the register bit field. - \param[in] value Value of the bit field. + \param[in] value Value of the bit field. This parameter is interpreted as an uint32_t type. \return Masked and shifted value. */ -#define _VAL2FLD(field, value) ((value << field ## _Pos) & field ## _Msk) +#define _VAL2FLD(field, value) (((uint32_t)(value) << field ## _Pos) & field ## _Msk) /** \brief Mask and shift a register value to extract a bit filed value. \param[in] field Name of the register bit field. - \param[in] value Value of register. + \param[in] value Value of register. This parameter is interpreted as an uint32_t type. \return Masked and shifted bit field value. */ -#define _FLD2VAL(field, value) ((value & field ## _Msk) >> field ## _Pos) +#define _FLD2VAL(field, value) (((uint32_t)(value) & field ## _Msk) >> field ## _Pos) /*@} end of group CMSIS_core_bitfield */ @@ -1360,7 +1379,7 @@ typedef struct @{ */ -/* Memory mapping of Cortex-M3 Hardware */ +/* Memory mapping of Core Hardware */ #define SCS_BASE (0xE000E000UL) /*!< System Control Space Base Address */ #define ITM_BASE (0xE0000000UL) /*!< ITM Base Address */ #define DWT_BASE (0xE0001000UL) /*!< DWT Base Address */ @@ -1379,7 +1398,7 @@ typedef struct #define TPI ((TPI_Type *) TPI_BASE ) /*!< TPI configuration struct */ #define CoreDebug ((CoreDebug_Type *) CoreDebug_BASE) /*!< Core Debug configuration struct */ -#if (__MPU_PRESENT == 1U) +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) #define MPU_BASE (SCS_BASE + 0x0D90UL) /*!< Memory Protection Unit */ #define MPU ((MPU_Type *) MPU_BASE ) /*!< Memory Protection Unit */ #endif @@ -1410,6 +1429,45 @@ typedef struct @{ */ +#ifdef CMSIS_NVIC_VIRTUAL +#ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE +#define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h" +#endif +#include CMSIS_NVIC_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetPriorityGrouping __NVIC_SetPriorityGrouping +#define NVIC_GetPriorityGrouping __NVIC_GetPriorityGrouping +#define NVIC_EnableIRQ __NVIC_EnableIRQ +#define NVIC_GetEnableIRQ __NVIC_GetEnableIRQ +#define NVIC_DisableIRQ __NVIC_DisableIRQ +#define NVIC_GetPendingIRQ __NVIC_GetPendingIRQ +#define NVIC_SetPendingIRQ __NVIC_SetPendingIRQ +#define NVIC_ClearPendingIRQ __NVIC_ClearPendingIRQ +#define NVIC_GetActive __NVIC_GetActive +#define NVIC_SetPriority __NVIC_SetPriority +#define NVIC_GetPriority __NVIC_GetPriority +#define NVIC_SystemReset __NVIC_SystemReset +#endif /* CMSIS_NVIC_VIRTUAL */ + +#ifdef CMSIS_VECTAB_VIRTUAL +#ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h" +#endif +#include CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetVector __NVIC_SetVector +#define NVIC_GetVector __NVIC_GetVector +#endif /* (CMSIS_VECTAB_VIRTUAL) */ + +#define NVIC_USER_IRQ_OFFSET 16 + + +/* The following EXC_RETURN values are saved the LR on exception entry */ +#define EXC_RETURN_HANDLER (0xFFFFFFF1UL) /* return to Handler mode, uses MSP after return */ +#define EXC_RETURN_THREAD_MSP (0xFFFFFFF9UL) /* return to Thread mode, uses MSP after return */ +#define EXC_RETURN_THREAD_PSP (0xFFFFFFFDUL) /* return to Thread mode, uses PSP after return */ + + /** \brief Set Priority Grouping \details Sets the priority grouping field using the required unlock sequence. @@ -1419,15 +1477,16 @@ typedef struct priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set. \param [in] PriorityGroup Priority grouping field. */ -__STATIC_INLINE void NVIC_SetPriorityGrouping(uint32_t PriorityGroup) +__STATIC_INLINE void __NVIC_SetPriorityGrouping(uint32_t PriorityGroup) { uint32_t reg_value; uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + reg_value = SCB->AIRCR; /* read old register configuration */ reg_value &= ~((uint32_t)(SCB_AIRCR_VECTKEY_Msk | SCB_AIRCR_PRIGROUP_Msk)); /* clear bits to change */ reg_value = (reg_value | ((uint32_t)0x5FAUL << SCB_AIRCR_VECTKEY_Pos) | - (PriorityGroupTmp << 8U) ); /* Insert write key and priorty group */ + (PriorityGroupTmp << SCB_AIRCR_PRIGROUP_Pos) ); /* Insert write key and priority group */ SCB->AIRCR = reg_value; } @@ -1437,120 +1496,178 @@ __STATIC_INLINE void NVIC_SetPriorityGrouping(uint32_t PriorityGroup) \details Reads the priority grouping field from the NVIC Interrupt Controller. \return Priority grouping field (SCB->AIRCR [10:8] PRIGROUP field). */ -__STATIC_INLINE uint32_t NVIC_GetPriorityGrouping(void) +__STATIC_INLINE uint32_t __NVIC_GetPriorityGrouping(void) { return ((uint32_t)((SCB->AIRCR & SCB_AIRCR_PRIGROUP_Msk) >> SCB_AIRCR_PRIGROUP_Pos)); } /** - \brief Enable External Interrupt - \details Enables a device-specific interrupt in the NVIC interrupt controller. - \param [in] IRQn External interrupt number. Value cannot be negative. + \brief Enable Interrupt + \details Enables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Interrupt Enable status + \details Returns a device specific interrupt enable status from the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_EnableIRQ(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn) { - NVIC->ISER[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** - \brief Disable External Interrupt - \details Disables a device-specific interrupt in the NVIC interrupt controller. - \param [in] IRQn External interrupt number. Value cannot be negative. + \brief Disable Interrupt + \details Disables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_DisableIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn) { - NVIC->ICER[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + __DSB(); + __ISB(); + } } /** \brief Get Pending Interrupt - \details Reads the pending register in the NVIC and returns the pending bit for the specified interrupt. - \param [in] IRQn Interrupt number. + \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. \return 0 Interrupt status is not pending. \return 1 Interrupt status is pending. + \note IRQn must not be negative. */ -__STATIC_INLINE uint32_t NVIC_GetPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn) { - return ((uint32_t)(((NVIC->ISPR[(((uint32_t)(int32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** \brief Set Pending Interrupt - \details Sets the pending bit of an external interrupt. - \param [in] IRQn Interrupt number. Value cannot be negative. + \details Sets the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_SetPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn) { - NVIC->ISPR[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** \brief Clear Pending Interrupt - \details Clears the pending bit of an external interrupt. - \param [in] IRQn External interrupt number. Value cannot be negative. + \details Clears the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_ClearPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn) { - NVIC->ICPR[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** \brief Get Active Interrupt - \details Reads the active register in NVIC and returns the active bit. - \param [in] IRQn Interrupt number. + \details Reads the active register in the NVIC and returns the active bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. \return 0 Interrupt status is not active. \return 1 Interrupt status is active. + \note IRQn must not be negative. */ -__STATIC_INLINE uint32_t NVIC_GetActive(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetActive(IRQn_Type IRQn) { - return ((uint32_t)(((NVIC->IABR[(((uint32_t)(int32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->IABR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** \brief Set Interrupt Priority - \details Sets the priority of an interrupt. - \note The priority cannot be set for every core interrupt. + \details Sets the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. \param [in] IRQn Interrupt number. \param [in] priority Priority to set. + \note The priority cannot be set for every processor exception. */ -__STATIC_INLINE void NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) +__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) { - if ((int32_t)(IRQn) < 0) + if ((int32_t)(IRQn) >= 0) { - SCB->SHP[(((uint32_t)(int32_t)IRQn) & 0xFUL) - 4UL] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + NVIC->IP[((uint32_t)IRQn)] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); } else { - NVIC->IP[((uint32_t)(int32_t)IRQn)] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + SCB->SHP[(((uint32_t)IRQn) & 0xFUL) - 4UL] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); } } /** \brief Get Interrupt Priority - \details Reads the priority of an interrupt. - The interrupt number can be positive to specify an external (device specific) interrupt, - or negative to specify an internal (core) interrupt. + \details Reads the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. \param [in] IRQn Interrupt number. \return Interrupt Priority. Value is aligned automatically to the implemented priority bits of the microcontroller. */ -__STATIC_INLINE uint32_t NVIC_GetPriority(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn) { - if ((int32_t)(IRQn) < 0) + + if ((int32_t)(IRQn) >= 0) { - return (((uint32_t)SCB->SHP[(((uint32_t)(int32_t)IRQn) & 0xFUL) - 4UL] >> (8U - __NVIC_PRIO_BITS))); + return (((uint32_t)NVIC->IP[((uint32_t)IRQn)] >> (8U - __NVIC_PRIO_BITS))); } else { - return (((uint32_t)NVIC->IP[((uint32_t)(int32_t)IRQn)] >> (8U - __NVIC_PRIO_BITS))); + return (((uint32_t)SCB->SHP[(((uint32_t)IRQn) & 0xFUL) - 4UL] >> (8U - __NVIC_PRIO_BITS))); } } @@ -1571,8 +1688,10 @@ __STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t P uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ uint32_t PreemptPriorityBits; uint32_t SubPriorityBits; + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + return ( ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) | ((SubPriority & (uint32_t)((1UL << (SubPriorityBits )) - 1UL))) @@ -1596,18 +1715,51 @@ __STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGr uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ uint32_t PreemptPriorityBits; uint32_t SubPriorityBits; + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL); *pSubPriority = (Priority ) & (uint32_t)((1UL << (SubPriorityBits )) - 1UL); } +/** + \brief Set Interrupt Vector + \details Sets an interrupt vector in SRAM based interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + VTOR must been relocated to SRAM before. + \param [in] IRQn Interrupt number + \param [in] vector Address of interrupt handler function + */ +__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector) +{ + uint32_t* vectors = (uint32_t*)SCB->VTOR; + vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector; +} + + +/** + \brief Get Interrupt Vector + \details Reads an interrupt vector from interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Address of interrupt handler function + */ +__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn) +{ + uint32_t* vectors = (uint32_t*)SCB->VTOR; + return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET]; +} + + /** \brief System Reset \details Initiates a system reset request to reset the MCU. */ -__STATIC_INLINE void NVIC_SystemReset(void) +__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void) { __DSB(); /* Ensure all outstanding memory accesses included buffered write are completed before reset */ @@ -1624,6 +1776,38 @@ __STATIC_INLINE void NVIC_SystemReset(void) /*@} end of CMSIS_Core_NVICFunctions */ +/* ########################## MPU functions #################################### */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) + +#include "mpu_armv7.h" + +#endif + +/* ########################## FPU functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_FpuFunctions FPU Functions + \brief Function that provides FPU type. + @{ + */ + +/** + \brief get FPU type + \details returns the FPU type + \returns + - \b 0: No FPU + - \b 1: Single precision FPU + - \b 2: Double + Single precision FPU + */ +__STATIC_INLINE uint32_t SCB_GetFPUType(void) +{ + return 0U; /* No FPU */ +} + + +/*@} end of CMSIS_Core_FpuFunctions */ + /* ################################## SysTick function ############################################ */ @@ -1634,7 +1818,7 @@ __STATIC_INLINE void NVIC_SystemReset(void) @{ */ -#if (__Vendor_SysTickConfig == 0U) +#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U) /** \brief System Tick Configuration @@ -1677,8 +1861,8 @@ __STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks) @{ */ -extern volatile int32_t ITM_RxBuffer; /*!< External variable to receive characters. */ -#define ITM_RXBUFFER_EMPTY 0x5AA55AA5U /*!< Value identifying \ref ITM_RxBuffer is ready for next character. */ +extern volatile int32_t ITM_RxBuffer; /*!< External variable to receive characters. */ +#define ITM_RXBUFFER_EMPTY ((int32_t)0x5AA55AA5U) /*!< Value identifying \ref ITM_RxBuffer is ready for next character. */ /** @@ -1734,6 +1918,7 @@ __STATIC_INLINE int32_t ITM_ReceiveChar (void) */ __STATIC_INLINE int32_t ITM_CheckChar (void) { + if (ITM_RxBuffer == ITM_RXBUFFER_EMPTY) { return (0); /* no character available */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/core_cm33.h b/EpsilonLights/Drivers/CMSIS/Include/core_cm33.h new file mode 100644 index 00000000..6e9f20e0 --- /dev/null +++ b/EpsilonLights/Drivers/CMSIS/Include/core_cm33.h @@ -0,0 +1,3007 @@ +/**************************************************************************//** + * @file core_cm33.h + * @brief CMSIS Cortex-M33 Core Peripheral Access Layer Header File + * @version V5.0.9 + * @date 06. July 2018 + ******************************************************************************/ +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ + +#if defined ( __ICCARM__ ) +#pragma system_include /* treat file as system include file for MISRA check */ +#elif defined (__clang__) +#pragma clang system_header /* treat file as system include file */ +#endif + +#ifndef __CORE_CM33_H_GENERIC +#define __CORE_CM33_H_GENERIC + +#include + +#ifdef __cplusplus +extern "C" { +#endif + +/** + \page CMSIS_MISRA_Exceptions MISRA-C:2004 Compliance Exceptions + CMSIS violates the following MISRA-C:2004 rules: + + \li Required Rule 8.5, object/function definition in header file.
+ Function definitions in header files are used to allow 'inlining'. + + \li Required Rule 18.4, declaration of union type or object of union type: '{...}'.
+ Unions are used for effective representation of core registers. + + \li Advisory Rule 19.7, Function-like macro defined.
+ Function-like macros are used to allow more efficient code. + */ + + +/******************************************************************************* + * CMSIS definitions + ******************************************************************************/ +/** + \ingroup Cortex_M33 + @{ + */ + +#include "cmsis_version.h" + +/* CMSIS CM33 definitions */ +#define __CM33_CMSIS_VERSION_MAIN (__CM_CMSIS_VERSION_MAIN) /*!< \deprecated [31:16] CMSIS HAL main version */ +#define __CM33_CMSIS_VERSION_SUB (__CM_CMSIS_VERSION_SUB) /*!< \deprecated [15:0] CMSIS HAL sub version */ +#define __CM33_CMSIS_VERSION ((__CM33_CMSIS_VERSION_MAIN << 16U) | \ + __CM33_CMSIS_VERSION_SUB ) /*!< \deprecated CMSIS HAL version number */ + +#define __CORTEX_M (33U) /*!< Cortex-M Core */ + +/** __FPU_USED indicates whether an FPU is used or not. + For this, __FPU_PRESENT has to be checked prior to making use of FPU specific registers and functions. +*/ +#if defined ( __CC_ARM ) +#if defined (__TARGET_FPU_VFP) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) +#define __FPU_USED 1U +#else +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#define __FPU_USED 0U +#endif +#else +#define __FPU_USED 0U +#endif + +#if defined (__ARM_FEATURE_DSP) && (__ARM_FEATURE_DSP == 1U) +#if defined (__DSP_PRESENT) && (__DSP_PRESENT == 1U) +#define __DSP_USED 1U +#else +#error "Compiler generates DSP (SIMD) instructions for a devices without DSP extensions (check __DSP_PRESENT)" +#define __DSP_USED 0U +#endif +#else +#define __DSP_USED 0U +#endif + +#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#if defined (__ARM_PCS_VFP) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) +#define __FPU_USED 1U +#else +#warning "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#define __FPU_USED 0U +#endif +#else +#define __FPU_USED 0U +#endif + +#if defined (__ARM_FEATURE_DSP) && (__ARM_FEATURE_DSP == 1U) +#if defined (__DSP_PRESENT) && (__DSP_PRESENT == 1U) +#define __DSP_USED 1U +#else +#error "Compiler generates DSP (SIMD) instructions for a devices without DSP extensions (check __DSP_PRESENT)" +#define __DSP_USED 0U +#endif +#else +#define __DSP_USED 0U +#endif + +#elif defined ( __GNUC__ ) +#if defined (__VFP_FP__) && !defined(__SOFTFP__) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) +#define __FPU_USED 1U +#else +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#define __FPU_USED 0U +#endif +#else +#define __FPU_USED 0U +#endif + +#if defined (__ARM_FEATURE_DSP) && (__ARM_FEATURE_DSP == 1U) +#if defined (__DSP_PRESENT) && (__DSP_PRESENT == 1U) +#define __DSP_USED 1U +#else +#error "Compiler generates DSP (SIMD) instructions for a devices without DSP extensions (check __DSP_PRESENT)" +#define __DSP_USED 0U +#endif +#else +#define __DSP_USED 0U +#endif + +#elif defined ( __ICCARM__ ) +#if defined (__ARMVFP__) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) +#define __FPU_USED 1U +#else +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#define __FPU_USED 0U +#endif +#else +#define __FPU_USED 0U +#endif + +#if defined (__ARM_FEATURE_DSP) && (__ARM_FEATURE_DSP == 1U) +#if defined (__DSP_PRESENT) && (__DSP_PRESENT == 1U) +#define __DSP_USED 1U +#else +#error "Compiler generates DSP (SIMD) instructions for a devices without DSP extensions (check __DSP_PRESENT)" +#define __DSP_USED 0U +#endif +#else +#define __DSP_USED 0U +#endif + +#elif defined ( __TI_ARM__ ) +#if defined (__TI_VFP_SUPPORT__) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) +#define __FPU_USED 1U +#else +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#define __FPU_USED 0U +#endif +#else +#define __FPU_USED 0U +#endif + +#elif defined ( __TASKING__ ) +#if defined (__FPU_VFP__) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) +#define __FPU_USED 1U +#else +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#define __FPU_USED 0U +#endif +#else +#define __FPU_USED 0U +#endif + +#elif defined ( __CSMC__ ) +#if ( __CSMC__ & 0x400U) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) +#define __FPU_USED 1U +#else +#error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" +#define __FPU_USED 0U +#endif +#else +#define __FPU_USED 0U +#endif + +#endif + +#include "cmsis_compiler.h" /* CMSIS compiler specific defines */ + + +#ifdef __cplusplus +} +#endif + +#endif /* __CORE_CM33_H_GENERIC */ + +#ifndef __CMSIS_GENERIC + +#ifndef __CORE_CM33_H_DEPENDANT +#define __CORE_CM33_H_DEPENDANT + +#ifdef __cplusplus +extern "C" { +#endif + +/* check device defines and use defaults */ +#if defined __CHECK_DEVICE_DEFINES +#ifndef __CM33_REV +#define __CM33_REV 0x0000U +#warning "__CM33_REV not defined in device header file; using default!" +#endif + +#ifndef __FPU_PRESENT +#define __FPU_PRESENT 0U +#warning "__FPU_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __MPU_PRESENT +#define __MPU_PRESENT 0U +#warning "__MPU_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __SAUREGION_PRESENT +#define __SAUREGION_PRESENT 0U +#warning "__SAUREGION_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __DSP_PRESENT +#define __DSP_PRESENT 0U +#warning "__DSP_PRESENT not defined in device header file; using default!" +#endif + +#ifndef __NVIC_PRIO_BITS +#define __NVIC_PRIO_BITS 3U +#warning "__NVIC_PRIO_BITS not defined in device header file; using default!" +#endif + +#ifndef __Vendor_SysTickConfig +#define __Vendor_SysTickConfig 0U +#warning "__Vendor_SysTickConfig not defined in device header file; using default!" +#endif +#endif + +/* IO definitions (access restrictions to peripheral registers) */ +/** + \defgroup CMSIS_glob_defs CMSIS Global Defines + + IO Type Qualifiers are used + \li to specify the access to peripheral variables. + \li for automatic generation of peripheral register debug information. +*/ +#ifdef __cplusplus +#define __I volatile /*!< Defines 'read only' permissions */ +#else +#define __I volatile const /*!< Defines 'read only' permissions */ +#endif +#define __O volatile /*!< Defines 'write only' permissions */ +#define __IO volatile /*!< Defines 'read / write' permissions */ + +/* following defines should be used for structure members */ +#define __IM volatile const /*! Defines 'read only' structure member permissions */ +#define __OM volatile /*! Defines 'write only' structure member permissions */ +#define __IOM volatile /*! Defines 'read / write' structure member permissions */ + +/*@} end of group Cortex_M33 */ + + + +/******************************************************************************* + * Register Abstraction + Core Register contain: + - Core Register + - Core NVIC Register + - Core SCB Register + - Core SysTick Register + - Core Debug Register + - Core MPU Register + - Core SAU Register + - Core FPU Register + ******************************************************************************/ +/** + \defgroup CMSIS_core_register Defines and Type Definitions + \brief Type definitions and defines for Cortex-M processor based devices. +*/ + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_CORE Status and Control Registers + \brief Core Register type definitions. + @{ + */ + +/** + \brief Union type to access the Application Program Status Register (APSR). + */ +typedef union +{ + struct + { + uint32_t _reserved0: 16; /*!< bit: 0..15 Reserved */ + uint32_t GE: 4; /*!< bit: 16..19 Greater than or Equal flags */ + uint32_t _reserved1: 7; /*!< bit: 20..26 Reserved */ + uint32_t Q: 1; /*!< bit: 27 Saturation condition flag */ + uint32_t V: 1; /*!< bit: 28 Overflow condition code flag */ + uint32_t C: 1; /*!< bit: 29 Carry condition code flag */ + uint32_t Z: 1; /*!< bit: 30 Zero condition code flag */ + uint32_t N: 1; /*!< bit: 31 Negative condition code flag */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} APSR_Type; + +/* APSR Register Definitions */ +#define APSR_N_Pos 31U /*!< APSR: N Position */ +#define APSR_N_Msk (1UL << APSR_N_Pos) /*!< APSR: N Mask */ + +#define APSR_Z_Pos 30U /*!< APSR: Z Position */ +#define APSR_Z_Msk (1UL << APSR_Z_Pos) /*!< APSR: Z Mask */ + +#define APSR_C_Pos 29U /*!< APSR: C Position */ +#define APSR_C_Msk (1UL << APSR_C_Pos) /*!< APSR: C Mask */ + +#define APSR_V_Pos 28U /*!< APSR: V Position */ +#define APSR_V_Msk (1UL << APSR_V_Pos) /*!< APSR: V Mask */ + +#define APSR_Q_Pos 27U /*!< APSR: Q Position */ +#define APSR_Q_Msk (1UL << APSR_Q_Pos) /*!< APSR: Q Mask */ + +#define APSR_GE_Pos 16U /*!< APSR: GE Position */ +#define APSR_GE_Msk (0xFUL << APSR_GE_Pos) /*!< APSR: GE Mask */ + + +/** + \brief Union type to access the Interrupt Program Status Register (IPSR). + */ +typedef union +{ + struct + { + uint32_t ISR: 9; /*!< bit: 0.. 8 Exception number */ + uint32_t _reserved0: 23; /*!< bit: 9..31 Reserved */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} IPSR_Type; + +/* IPSR Register Definitions */ +#define IPSR_ISR_Pos 0U /*!< IPSR: ISR Position */ +#define IPSR_ISR_Msk (0x1FFUL /*<< IPSR_ISR_Pos*/) /*!< IPSR: ISR Mask */ + + +/** + \brief Union type to access the Special-Purpose Program Status Registers (xPSR). + */ +typedef union +{ + struct + { + uint32_t ISR: 9; /*!< bit: 0.. 8 Exception number */ + uint32_t _reserved0: 7; /*!< bit: 9..15 Reserved */ + uint32_t GE: 4; /*!< bit: 16..19 Greater than or Equal flags */ + uint32_t _reserved1: 4; /*!< bit: 20..23 Reserved */ + uint32_t T: 1; /*!< bit: 24 Thumb bit (read 0) */ + uint32_t IT: 2; /*!< bit: 25..26 saved IT state (read 0) */ + uint32_t Q: 1; /*!< bit: 27 Saturation condition flag */ + uint32_t V: 1; /*!< bit: 28 Overflow condition code flag */ + uint32_t C: 1; /*!< bit: 29 Carry condition code flag */ + uint32_t Z: 1; /*!< bit: 30 Zero condition code flag */ + uint32_t N: 1; /*!< bit: 31 Negative condition code flag */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} xPSR_Type; + +/* xPSR Register Definitions */ +#define xPSR_N_Pos 31U /*!< xPSR: N Position */ +#define xPSR_N_Msk (1UL << xPSR_N_Pos) /*!< xPSR: N Mask */ + +#define xPSR_Z_Pos 30U /*!< xPSR: Z Position */ +#define xPSR_Z_Msk (1UL << xPSR_Z_Pos) /*!< xPSR: Z Mask */ + +#define xPSR_C_Pos 29U /*!< xPSR: C Position */ +#define xPSR_C_Msk (1UL << xPSR_C_Pos) /*!< xPSR: C Mask */ + +#define xPSR_V_Pos 28U /*!< xPSR: V Position */ +#define xPSR_V_Msk (1UL << xPSR_V_Pos) /*!< xPSR: V Mask */ + +#define xPSR_Q_Pos 27U /*!< xPSR: Q Position */ +#define xPSR_Q_Msk (1UL << xPSR_Q_Pos) /*!< xPSR: Q Mask */ + +#define xPSR_IT_Pos 25U /*!< xPSR: IT Position */ +#define xPSR_IT_Msk (3UL << xPSR_IT_Pos) /*!< xPSR: IT Mask */ + +#define xPSR_T_Pos 24U /*!< xPSR: T Position */ +#define xPSR_T_Msk (1UL << xPSR_T_Pos) /*!< xPSR: T Mask */ + +#define xPSR_GE_Pos 16U /*!< xPSR: GE Position */ +#define xPSR_GE_Msk (0xFUL << xPSR_GE_Pos) /*!< xPSR: GE Mask */ + +#define xPSR_ISR_Pos 0U /*!< xPSR: ISR Position */ +#define xPSR_ISR_Msk (0x1FFUL /*<< xPSR_ISR_Pos*/) /*!< xPSR: ISR Mask */ + + +/** + \brief Union type to access the Control Registers (CONTROL). + */ +typedef union +{ + struct + { + uint32_t nPRIV: 1; /*!< bit: 0 Execution privilege in Thread mode */ + uint32_t SPSEL: 1; /*!< bit: 1 Stack-pointer select */ + uint32_t FPCA: 1; /*!< bit: 2 Floating-point context active */ + uint32_t SFPA: 1; /*!< bit: 3 Secure floating-point active */ + uint32_t _reserved1: 28; /*!< bit: 4..31 Reserved */ + } b; /*!< Structure used for bit access */ + uint32_t w; /*!< Type used for word access */ +} CONTROL_Type; + +/* CONTROL Register Definitions */ +#define CONTROL_SFPA_Pos 3U /*!< CONTROL: SFPA Position */ +#define CONTROL_SFPA_Msk (1UL << CONTROL_SFPA_Pos) /*!< CONTROL: SFPA Mask */ + +#define CONTROL_FPCA_Pos 2U /*!< CONTROL: FPCA Position */ +#define CONTROL_FPCA_Msk (1UL << CONTROL_FPCA_Pos) /*!< CONTROL: FPCA Mask */ + +#define CONTROL_SPSEL_Pos 1U /*!< CONTROL: SPSEL Position */ +#define CONTROL_SPSEL_Msk (1UL << CONTROL_SPSEL_Pos) /*!< CONTROL: SPSEL Mask */ + +#define CONTROL_nPRIV_Pos 0U /*!< CONTROL: nPRIV Position */ +#define CONTROL_nPRIV_Msk (1UL /*<< CONTROL_nPRIV_Pos*/) /*!< CONTROL: nPRIV Mask */ + +/*@} end of group CMSIS_CORE */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_NVIC Nested Vectored Interrupt Controller (NVIC) + \brief Type definitions for the NVIC Registers + @{ + */ + +/** + \brief Structure type to access the Nested Vectored Interrupt Controller (NVIC). + */ +typedef struct +{ + __IOM uint32_t ISER[16U]; /*!< Offset: 0x000 (R/W) Interrupt Set Enable Register */ + uint32_t RESERVED0[16U]; + __IOM uint32_t ICER[16U]; /*!< Offset: 0x080 (R/W) Interrupt Clear Enable Register */ + uint32_t RSERVED1[16U]; + __IOM uint32_t ISPR[16U]; /*!< Offset: 0x100 (R/W) Interrupt Set Pending Register */ + uint32_t RESERVED2[16U]; + __IOM uint32_t ICPR[16U]; /*!< Offset: 0x180 (R/W) Interrupt Clear Pending Register */ + uint32_t RESERVED3[16U]; + __IOM uint32_t IABR[16U]; /*!< Offset: 0x200 (R/W) Interrupt Active bit Register */ + uint32_t RESERVED4[16U]; + __IOM uint32_t ITNS[16U]; /*!< Offset: 0x280 (R/W) Interrupt Non-Secure State Register */ + uint32_t RESERVED5[16U]; + __IOM uint8_t IPR[496U]; /*!< Offset: 0x300 (R/W) Interrupt Priority Register (8Bit wide) */ + uint32_t RESERVED6[580U]; + __OM uint32_t STIR; /*!< Offset: 0xE00 ( /W) Software Trigger Interrupt Register */ +} NVIC_Type; + +/* Software Triggered Interrupt Register Definitions */ +#define NVIC_STIR_INTID_Pos 0U /*!< STIR: INTLINESNUM Position */ +#define NVIC_STIR_INTID_Msk (0x1FFUL /*<< NVIC_STIR_INTID_Pos*/) /*!< STIR: INTLINESNUM Mask */ + +/*@} end of group CMSIS_NVIC */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SCB System Control Block (SCB) + \brief Type definitions for the System Control Block Registers + @{ + */ + +/** + \brief Structure type to access the System Control Block (SCB). + */ +typedef struct +{ + __IM uint32_t CPUID; /*!< Offset: 0x000 (R/ ) CPUID Base Register */ + __IOM uint32_t ICSR; /*!< Offset: 0x004 (R/W) Interrupt Control and State Register */ + __IOM uint32_t VTOR; /*!< Offset: 0x008 (R/W) Vector Table Offset Register */ + __IOM uint32_t AIRCR; /*!< Offset: 0x00C (R/W) Application Interrupt and Reset Control Register */ + __IOM uint32_t SCR; /*!< Offset: 0x010 (R/W) System Control Register */ + __IOM uint32_t CCR; /*!< Offset: 0x014 (R/W) Configuration Control Register */ + __IOM uint8_t SHPR[12U]; /*!< Offset: 0x018 (R/W) System Handlers Priority Registers (4-7, 8-11, 12-15) */ + __IOM uint32_t SHCSR; /*!< Offset: 0x024 (R/W) System Handler Control and State Register */ + __IOM uint32_t CFSR; /*!< Offset: 0x028 (R/W) Configurable Fault Status Register */ + __IOM uint32_t HFSR; /*!< Offset: 0x02C (R/W) HardFault Status Register */ + __IOM uint32_t DFSR; /*!< Offset: 0x030 (R/W) Debug Fault Status Register */ + __IOM uint32_t MMFAR; /*!< Offset: 0x034 (R/W) MemManage Fault Address Register */ + __IOM uint32_t BFAR; /*!< Offset: 0x038 (R/W) BusFault Address Register */ + __IOM uint32_t AFSR; /*!< Offset: 0x03C (R/W) Auxiliary Fault Status Register */ + __IM uint32_t ID_PFR[2U]; /*!< Offset: 0x040 (R/ ) Processor Feature Register */ + __IM uint32_t ID_DFR; /*!< Offset: 0x048 (R/ ) Debug Feature Register */ + __IM uint32_t ID_ADR; /*!< Offset: 0x04C (R/ ) Auxiliary Feature Register */ + __IM uint32_t ID_MMFR[4U]; /*!< Offset: 0x050 (R/ ) Memory Model Feature Register */ + __IM uint32_t ID_ISAR[6U]; /*!< Offset: 0x060 (R/ ) Instruction Set Attributes Register */ + __IM uint32_t CLIDR; /*!< Offset: 0x078 (R/ ) Cache Level ID register */ + __IM uint32_t CTR; /*!< Offset: 0x07C (R/ ) Cache Type register */ + __IM uint32_t CCSIDR; /*!< Offset: 0x080 (R/ ) Cache Size ID Register */ + __IOM uint32_t CSSELR; /*!< Offset: 0x084 (R/W) Cache Size Selection Register */ + __IOM uint32_t CPACR; /*!< Offset: 0x088 (R/W) Coprocessor Access Control Register */ + __IOM uint32_t NSACR; /*!< Offset: 0x08C (R/W) Non-Secure Access Control Register */ + uint32_t RESERVED3[92U]; + __OM uint32_t STIR; /*!< Offset: 0x200 ( /W) Software Triggered Interrupt Register */ + uint32_t RESERVED4[15U]; + __IM uint32_t MVFR0; /*!< Offset: 0x240 (R/ ) Media and VFP Feature Register 0 */ + __IM uint32_t MVFR1; /*!< Offset: 0x244 (R/ ) Media and VFP Feature Register 1 */ + __IM uint32_t MVFR2; /*!< Offset: 0x248 (R/ ) Media and VFP Feature Register 2 */ + uint32_t RESERVED5[1U]; + __OM uint32_t ICIALLU; /*!< Offset: 0x250 ( /W) I-Cache Invalidate All to PoU */ + uint32_t RESERVED6[1U]; + __OM uint32_t ICIMVAU; /*!< Offset: 0x258 ( /W) I-Cache Invalidate by MVA to PoU */ + __OM uint32_t DCIMVAC; /*!< Offset: 0x25C ( /W) D-Cache Invalidate by MVA to PoC */ + __OM uint32_t DCISW; /*!< Offset: 0x260 ( /W) D-Cache Invalidate by Set-way */ + __OM uint32_t DCCMVAU; /*!< Offset: 0x264 ( /W) D-Cache Clean by MVA to PoU */ + __OM uint32_t DCCMVAC; /*!< Offset: 0x268 ( /W) D-Cache Clean by MVA to PoC */ + __OM uint32_t DCCSW; /*!< Offset: 0x26C ( /W) D-Cache Clean by Set-way */ + __OM uint32_t DCCIMVAC; /*!< Offset: 0x270 ( /W) D-Cache Clean and Invalidate by MVA to PoC */ + __OM uint32_t DCCISW; /*!< Offset: 0x274 ( /W) D-Cache Clean and Invalidate by Set-way */ + uint32_t RESERVED7[6U]; + __IOM uint32_t ITCMCR; /*!< Offset: 0x290 (R/W) Instruction Tightly-Coupled Memory Control Register */ + __IOM uint32_t DTCMCR; /*!< Offset: 0x294 (R/W) Data Tightly-Coupled Memory Control Registers */ + __IOM uint32_t AHBPCR; /*!< Offset: 0x298 (R/W) AHBP Control Register */ + __IOM uint32_t CACR; /*!< Offset: 0x29C (R/W) L1 Cache Control Register */ + __IOM uint32_t AHBSCR; /*!< Offset: 0x2A0 (R/W) AHB Slave Control Register */ + uint32_t RESERVED8[1U]; + __IOM uint32_t ABFSR; /*!< Offset: 0x2A8 (R/W) Auxiliary Bus Fault Status Register */ +} SCB_Type; + +/* SCB CPUID Register Definitions */ +#define SCB_CPUID_IMPLEMENTER_Pos 24U /*!< SCB CPUID: IMPLEMENTER Position */ +#define SCB_CPUID_IMPLEMENTER_Msk (0xFFUL << SCB_CPUID_IMPLEMENTER_Pos) /*!< SCB CPUID: IMPLEMENTER Mask */ + +#define SCB_CPUID_VARIANT_Pos 20U /*!< SCB CPUID: VARIANT Position */ +#define SCB_CPUID_VARIANT_Msk (0xFUL << SCB_CPUID_VARIANT_Pos) /*!< SCB CPUID: VARIANT Mask */ + +#define SCB_CPUID_ARCHITECTURE_Pos 16U /*!< SCB CPUID: ARCHITECTURE Position */ +#define SCB_CPUID_ARCHITECTURE_Msk (0xFUL << SCB_CPUID_ARCHITECTURE_Pos) /*!< SCB CPUID: ARCHITECTURE Mask */ + +#define SCB_CPUID_PARTNO_Pos 4U /*!< SCB CPUID: PARTNO Position */ +#define SCB_CPUID_PARTNO_Msk (0xFFFUL << SCB_CPUID_PARTNO_Pos) /*!< SCB CPUID: PARTNO Mask */ + +#define SCB_CPUID_REVISION_Pos 0U /*!< SCB CPUID: REVISION Position */ +#define SCB_CPUID_REVISION_Msk (0xFUL /*<< SCB_CPUID_REVISION_Pos*/) /*!< SCB CPUID: REVISION Mask */ + +/* SCB Interrupt Control State Register Definitions */ +#define SCB_ICSR_PENDNMISET_Pos 31U /*!< SCB ICSR: PENDNMISET Position */ +#define SCB_ICSR_PENDNMISET_Msk (1UL << SCB_ICSR_PENDNMISET_Pos) /*!< SCB ICSR: PENDNMISET Mask */ + +#define SCB_ICSR_NMIPENDSET_Pos SCB_ICSR_PENDNMISET_Pos /*!< SCB ICSR: NMIPENDSET Position, backward compatibility */ +#define SCB_ICSR_NMIPENDSET_Msk SCB_ICSR_PENDNMISET_Msk /*!< SCB ICSR: NMIPENDSET Mask, backward compatibility */ + +#define SCB_ICSR_PENDNMICLR_Pos 30U /*!< SCB ICSR: PENDNMICLR Position */ +#define SCB_ICSR_PENDNMICLR_Msk (1UL << SCB_ICSR_PENDNMICLR_Pos) /*!< SCB ICSR: PENDNMICLR Mask */ + +#define SCB_ICSR_PENDSVSET_Pos 28U /*!< SCB ICSR: PENDSVSET Position */ +#define SCB_ICSR_PENDSVSET_Msk (1UL << SCB_ICSR_PENDSVSET_Pos) /*!< SCB ICSR: PENDSVSET Mask */ + +#define SCB_ICSR_PENDSVCLR_Pos 27U /*!< SCB ICSR: PENDSVCLR Position */ +#define SCB_ICSR_PENDSVCLR_Msk (1UL << SCB_ICSR_PENDSVCLR_Pos) /*!< SCB ICSR: PENDSVCLR Mask */ + +#define SCB_ICSR_PENDSTSET_Pos 26U /*!< SCB ICSR: PENDSTSET Position */ +#define SCB_ICSR_PENDSTSET_Msk (1UL << SCB_ICSR_PENDSTSET_Pos) /*!< SCB ICSR: PENDSTSET Mask */ + +#define SCB_ICSR_PENDSTCLR_Pos 25U /*!< SCB ICSR: PENDSTCLR Position */ +#define SCB_ICSR_PENDSTCLR_Msk (1UL << SCB_ICSR_PENDSTCLR_Pos) /*!< SCB ICSR: PENDSTCLR Mask */ + +#define SCB_ICSR_STTNS_Pos 24U /*!< SCB ICSR: STTNS Position (Security Extension) */ +#define SCB_ICSR_STTNS_Msk (1UL << SCB_ICSR_STTNS_Pos) /*!< SCB ICSR: STTNS Mask (Security Extension) */ + +#define SCB_ICSR_ISRPREEMPT_Pos 23U /*!< SCB ICSR: ISRPREEMPT Position */ +#define SCB_ICSR_ISRPREEMPT_Msk (1UL << SCB_ICSR_ISRPREEMPT_Pos) /*!< SCB ICSR: ISRPREEMPT Mask */ + +#define SCB_ICSR_ISRPENDING_Pos 22U /*!< SCB ICSR: ISRPENDING Position */ +#define SCB_ICSR_ISRPENDING_Msk (1UL << SCB_ICSR_ISRPENDING_Pos) /*!< SCB ICSR: ISRPENDING Mask */ + +#define SCB_ICSR_VECTPENDING_Pos 12U /*!< SCB ICSR: VECTPENDING Position */ +#define SCB_ICSR_VECTPENDING_Msk (0x1FFUL << SCB_ICSR_VECTPENDING_Pos) /*!< SCB ICSR: VECTPENDING Mask */ + +#define SCB_ICSR_RETTOBASE_Pos 11U /*!< SCB ICSR: RETTOBASE Position */ +#define SCB_ICSR_RETTOBASE_Msk (1UL << SCB_ICSR_RETTOBASE_Pos) /*!< SCB ICSR: RETTOBASE Mask */ + +#define SCB_ICSR_VECTACTIVE_Pos 0U /*!< SCB ICSR: VECTACTIVE Position */ +#define SCB_ICSR_VECTACTIVE_Msk (0x1FFUL /*<< SCB_ICSR_VECTACTIVE_Pos*/) /*!< SCB ICSR: VECTACTIVE Mask */ + +/* SCB Vector Table Offset Register Definitions */ +#define SCB_VTOR_TBLOFF_Pos 7U /*!< SCB VTOR: TBLOFF Position */ +#define SCB_VTOR_TBLOFF_Msk (0x1FFFFFFUL << SCB_VTOR_TBLOFF_Pos) /*!< SCB VTOR: TBLOFF Mask */ + +/* SCB Application Interrupt and Reset Control Register Definitions */ +#define SCB_AIRCR_VECTKEY_Pos 16U /*!< SCB AIRCR: VECTKEY Position */ +#define SCB_AIRCR_VECTKEY_Msk (0xFFFFUL << SCB_AIRCR_VECTKEY_Pos) /*!< SCB AIRCR: VECTKEY Mask */ + +#define SCB_AIRCR_VECTKEYSTAT_Pos 16U /*!< SCB AIRCR: VECTKEYSTAT Position */ +#define SCB_AIRCR_VECTKEYSTAT_Msk (0xFFFFUL << SCB_AIRCR_VECTKEYSTAT_Pos) /*!< SCB AIRCR: VECTKEYSTAT Mask */ + +#define SCB_AIRCR_ENDIANESS_Pos 15U /*!< SCB AIRCR: ENDIANESS Position */ +#define SCB_AIRCR_ENDIANESS_Msk (1UL << SCB_AIRCR_ENDIANESS_Pos) /*!< SCB AIRCR: ENDIANESS Mask */ + +#define SCB_AIRCR_PRIS_Pos 14U /*!< SCB AIRCR: PRIS Position */ +#define SCB_AIRCR_PRIS_Msk (1UL << SCB_AIRCR_PRIS_Pos) /*!< SCB AIRCR: PRIS Mask */ + +#define SCB_AIRCR_BFHFNMINS_Pos 13U /*!< SCB AIRCR: BFHFNMINS Position */ +#define SCB_AIRCR_BFHFNMINS_Msk (1UL << SCB_AIRCR_BFHFNMINS_Pos) /*!< SCB AIRCR: BFHFNMINS Mask */ + +#define SCB_AIRCR_PRIGROUP_Pos 8U /*!< SCB AIRCR: PRIGROUP Position */ +#define SCB_AIRCR_PRIGROUP_Msk (7UL << SCB_AIRCR_PRIGROUP_Pos) /*!< SCB AIRCR: PRIGROUP Mask */ + +#define SCB_AIRCR_SYSRESETREQS_Pos 3U /*!< SCB AIRCR: SYSRESETREQS Position */ +#define SCB_AIRCR_SYSRESETREQS_Msk (1UL << SCB_AIRCR_SYSRESETREQS_Pos) /*!< SCB AIRCR: SYSRESETREQS Mask */ + +#define SCB_AIRCR_SYSRESETREQ_Pos 2U /*!< SCB AIRCR: SYSRESETREQ Position */ +#define SCB_AIRCR_SYSRESETREQ_Msk (1UL << SCB_AIRCR_SYSRESETREQ_Pos) /*!< SCB AIRCR: SYSRESETREQ Mask */ + +#define SCB_AIRCR_VECTCLRACTIVE_Pos 1U /*!< SCB AIRCR: VECTCLRACTIVE Position */ +#define SCB_AIRCR_VECTCLRACTIVE_Msk (1UL << SCB_AIRCR_VECTCLRACTIVE_Pos) /*!< SCB AIRCR: VECTCLRACTIVE Mask */ + +/* SCB System Control Register Definitions */ +#define SCB_SCR_SEVONPEND_Pos 4U /*!< SCB SCR: SEVONPEND Position */ +#define SCB_SCR_SEVONPEND_Msk (1UL << SCB_SCR_SEVONPEND_Pos) /*!< SCB SCR: SEVONPEND Mask */ + +#define SCB_SCR_SLEEPDEEPS_Pos 3U /*!< SCB SCR: SLEEPDEEPS Position */ +#define SCB_SCR_SLEEPDEEPS_Msk (1UL << SCB_SCR_SLEEPDEEPS_Pos) /*!< SCB SCR: SLEEPDEEPS Mask */ + +#define SCB_SCR_SLEEPDEEP_Pos 2U /*!< SCB SCR: SLEEPDEEP Position */ +#define SCB_SCR_SLEEPDEEP_Msk (1UL << SCB_SCR_SLEEPDEEP_Pos) /*!< SCB SCR: SLEEPDEEP Mask */ + +#define SCB_SCR_SLEEPONEXIT_Pos 1U /*!< SCB SCR: SLEEPONEXIT Position */ +#define SCB_SCR_SLEEPONEXIT_Msk (1UL << SCB_SCR_SLEEPONEXIT_Pos) /*!< SCB SCR: SLEEPONEXIT Mask */ + +/* SCB Configuration Control Register Definitions */ +#define SCB_CCR_BP_Pos 18U /*!< SCB CCR: BP Position */ +#define SCB_CCR_BP_Msk (1UL << SCB_CCR_BP_Pos) /*!< SCB CCR: BP Mask */ + +#define SCB_CCR_IC_Pos 17U /*!< SCB CCR: IC Position */ +#define SCB_CCR_IC_Msk (1UL << SCB_CCR_IC_Pos) /*!< SCB CCR: IC Mask */ + +#define SCB_CCR_DC_Pos 16U /*!< SCB CCR: DC Position */ +#define SCB_CCR_DC_Msk (1UL << SCB_CCR_DC_Pos) /*!< SCB CCR: DC Mask */ + +#define SCB_CCR_STKOFHFNMIGN_Pos 10U /*!< SCB CCR: STKOFHFNMIGN Position */ +#define SCB_CCR_STKOFHFNMIGN_Msk (1UL << SCB_CCR_STKOFHFNMIGN_Pos) /*!< SCB CCR: STKOFHFNMIGN Mask */ + +#define SCB_CCR_BFHFNMIGN_Pos 8U /*!< SCB CCR: BFHFNMIGN Position */ +#define SCB_CCR_BFHFNMIGN_Msk (1UL << SCB_CCR_BFHFNMIGN_Pos) /*!< SCB CCR: BFHFNMIGN Mask */ + +#define SCB_CCR_DIV_0_TRP_Pos 4U /*!< SCB CCR: DIV_0_TRP Position */ +#define SCB_CCR_DIV_0_TRP_Msk (1UL << SCB_CCR_DIV_0_TRP_Pos) /*!< SCB CCR: DIV_0_TRP Mask */ + +#define SCB_CCR_UNALIGN_TRP_Pos 3U /*!< SCB CCR: UNALIGN_TRP Position */ +#define SCB_CCR_UNALIGN_TRP_Msk (1UL << SCB_CCR_UNALIGN_TRP_Pos) /*!< SCB CCR: UNALIGN_TRP Mask */ + +#define SCB_CCR_USERSETMPEND_Pos 1U /*!< SCB CCR: USERSETMPEND Position */ +#define SCB_CCR_USERSETMPEND_Msk (1UL << SCB_CCR_USERSETMPEND_Pos) /*!< SCB CCR: USERSETMPEND Mask */ + +/* SCB System Handler Control and State Register Definitions */ +#define SCB_SHCSR_HARDFAULTPENDED_Pos 21U /*!< SCB SHCSR: HARDFAULTPENDED Position */ +#define SCB_SHCSR_HARDFAULTPENDED_Msk (1UL << SCB_SHCSR_HARDFAULTPENDED_Pos) /*!< SCB SHCSR: HARDFAULTPENDED Mask */ + +#define SCB_SHCSR_SECUREFAULTPENDED_Pos 20U /*!< SCB SHCSR: SECUREFAULTPENDED Position */ +#define SCB_SHCSR_SECUREFAULTPENDED_Msk (1UL << SCB_SHCSR_SECUREFAULTPENDED_Pos) /*!< SCB SHCSR: SECUREFAULTPENDED Mask */ + +#define SCB_SHCSR_SECUREFAULTENA_Pos 19U /*!< SCB SHCSR: SECUREFAULTENA Position */ +#define SCB_SHCSR_SECUREFAULTENA_Msk (1UL << SCB_SHCSR_SECUREFAULTENA_Pos) /*!< SCB SHCSR: SECUREFAULTENA Mask */ + +#define SCB_SHCSR_USGFAULTENA_Pos 18U /*!< SCB SHCSR: USGFAULTENA Position */ +#define SCB_SHCSR_USGFAULTENA_Msk (1UL << SCB_SHCSR_USGFAULTENA_Pos) /*!< SCB SHCSR: USGFAULTENA Mask */ + +#define SCB_SHCSR_BUSFAULTENA_Pos 17U /*!< SCB SHCSR: BUSFAULTENA Position */ +#define SCB_SHCSR_BUSFAULTENA_Msk (1UL << SCB_SHCSR_BUSFAULTENA_Pos) /*!< SCB SHCSR: BUSFAULTENA Mask */ + +#define SCB_SHCSR_MEMFAULTENA_Pos 16U /*!< SCB SHCSR: MEMFAULTENA Position */ +#define SCB_SHCSR_MEMFAULTENA_Msk (1UL << SCB_SHCSR_MEMFAULTENA_Pos) /*!< SCB SHCSR: MEMFAULTENA Mask */ + +#define SCB_SHCSR_SVCALLPENDED_Pos 15U /*!< SCB SHCSR: SVCALLPENDED Position */ +#define SCB_SHCSR_SVCALLPENDED_Msk (1UL << SCB_SHCSR_SVCALLPENDED_Pos) /*!< SCB SHCSR: SVCALLPENDED Mask */ + +#define SCB_SHCSR_BUSFAULTPENDED_Pos 14U /*!< SCB SHCSR: BUSFAULTPENDED Position */ +#define SCB_SHCSR_BUSFAULTPENDED_Msk (1UL << SCB_SHCSR_BUSFAULTPENDED_Pos) /*!< SCB SHCSR: BUSFAULTPENDED Mask */ + +#define SCB_SHCSR_MEMFAULTPENDED_Pos 13U /*!< SCB SHCSR: MEMFAULTPENDED Position */ +#define SCB_SHCSR_MEMFAULTPENDED_Msk (1UL << SCB_SHCSR_MEMFAULTPENDED_Pos) /*!< SCB SHCSR: MEMFAULTPENDED Mask */ + +#define SCB_SHCSR_USGFAULTPENDED_Pos 12U /*!< SCB SHCSR: USGFAULTPENDED Position */ +#define SCB_SHCSR_USGFAULTPENDED_Msk (1UL << SCB_SHCSR_USGFAULTPENDED_Pos) /*!< SCB SHCSR: USGFAULTPENDED Mask */ + +#define SCB_SHCSR_SYSTICKACT_Pos 11U /*!< SCB SHCSR: SYSTICKACT Position */ +#define SCB_SHCSR_SYSTICKACT_Msk (1UL << SCB_SHCSR_SYSTICKACT_Pos) /*!< SCB SHCSR: SYSTICKACT Mask */ + +#define SCB_SHCSR_PENDSVACT_Pos 10U /*!< SCB SHCSR: PENDSVACT Position */ +#define SCB_SHCSR_PENDSVACT_Msk (1UL << SCB_SHCSR_PENDSVACT_Pos) /*!< SCB SHCSR: PENDSVACT Mask */ + +#define SCB_SHCSR_MONITORACT_Pos 8U /*!< SCB SHCSR: MONITORACT Position */ +#define SCB_SHCSR_MONITORACT_Msk (1UL << SCB_SHCSR_MONITORACT_Pos) /*!< SCB SHCSR: MONITORACT Mask */ + +#define SCB_SHCSR_SVCALLACT_Pos 7U /*!< SCB SHCSR: SVCALLACT Position */ +#define SCB_SHCSR_SVCALLACT_Msk (1UL << SCB_SHCSR_SVCALLACT_Pos) /*!< SCB SHCSR: SVCALLACT Mask */ + +#define SCB_SHCSR_NMIACT_Pos 5U /*!< SCB SHCSR: NMIACT Position */ +#define SCB_SHCSR_NMIACT_Msk (1UL << SCB_SHCSR_NMIACT_Pos) /*!< SCB SHCSR: NMIACT Mask */ + +#define SCB_SHCSR_SECUREFAULTACT_Pos 4U /*!< SCB SHCSR: SECUREFAULTACT Position */ +#define SCB_SHCSR_SECUREFAULTACT_Msk (1UL << SCB_SHCSR_SECUREFAULTACT_Pos) /*!< SCB SHCSR: SECUREFAULTACT Mask */ + +#define SCB_SHCSR_USGFAULTACT_Pos 3U /*!< SCB SHCSR: USGFAULTACT Position */ +#define SCB_SHCSR_USGFAULTACT_Msk (1UL << SCB_SHCSR_USGFAULTACT_Pos) /*!< SCB SHCSR: USGFAULTACT Mask */ + +#define SCB_SHCSR_HARDFAULTACT_Pos 2U /*!< SCB SHCSR: HARDFAULTACT Position */ +#define SCB_SHCSR_HARDFAULTACT_Msk (1UL << SCB_SHCSR_HARDFAULTACT_Pos) /*!< SCB SHCSR: HARDFAULTACT Mask */ + +#define SCB_SHCSR_BUSFAULTACT_Pos 1U /*!< SCB SHCSR: BUSFAULTACT Position */ +#define SCB_SHCSR_BUSFAULTACT_Msk (1UL << SCB_SHCSR_BUSFAULTACT_Pos) /*!< SCB SHCSR: BUSFAULTACT Mask */ + +#define SCB_SHCSR_MEMFAULTACT_Pos 0U /*!< SCB SHCSR: MEMFAULTACT Position */ +#define SCB_SHCSR_MEMFAULTACT_Msk (1UL /*<< SCB_SHCSR_MEMFAULTACT_Pos*/) /*!< SCB SHCSR: MEMFAULTACT Mask */ + +/* SCB Configurable Fault Status Register Definitions */ +#define SCB_CFSR_USGFAULTSR_Pos 16U /*!< SCB CFSR: Usage Fault Status Register Position */ +#define SCB_CFSR_USGFAULTSR_Msk (0xFFFFUL << SCB_CFSR_USGFAULTSR_Pos) /*!< SCB CFSR: Usage Fault Status Register Mask */ + +#define SCB_CFSR_BUSFAULTSR_Pos 8U /*!< SCB CFSR: Bus Fault Status Register Position */ +#define SCB_CFSR_BUSFAULTSR_Msk (0xFFUL << SCB_CFSR_BUSFAULTSR_Pos) /*!< SCB CFSR: Bus Fault Status Register Mask */ + +#define SCB_CFSR_MEMFAULTSR_Pos 0U /*!< SCB CFSR: Memory Manage Fault Status Register Position */ +#define SCB_CFSR_MEMFAULTSR_Msk (0xFFUL /*<< SCB_CFSR_MEMFAULTSR_Pos*/) /*!< SCB CFSR: Memory Manage Fault Status Register Mask */ + +/* MemManage Fault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_MMARVALID_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 7U) /*!< SCB CFSR (MMFSR): MMARVALID Position */ +#define SCB_CFSR_MMARVALID_Msk (1UL << SCB_CFSR_MMARVALID_Pos) /*!< SCB CFSR (MMFSR): MMARVALID Mask */ + +#define SCB_CFSR_MLSPERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 5U) /*!< SCB CFSR (MMFSR): MLSPERR Position */ +#define SCB_CFSR_MLSPERR_Msk (1UL << SCB_CFSR_MLSPERR_Pos) /*!< SCB CFSR (MMFSR): MLSPERR Mask */ + +#define SCB_CFSR_MSTKERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 4U) /*!< SCB CFSR (MMFSR): MSTKERR Position */ +#define SCB_CFSR_MSTKERR_Msk (1UL << SCB_CFSR_MSTKERR_Pos) /*!< SCB CFSR (MMFSR): MSTKERR Mask */ + +#define SCB_CFSR_MUNSTKERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 3U) /*!< SCB CFSR (MMFSR): MUNSTKERR Position */ +#define SCB_CFSR_MUNSTKERR_Msk (1UL << SCB_CFSR_MUNSTKERR_Pos) /*!< SCB CFSR (MMFSR): MUNSTKERR Mask */ + +#define SCB_CFSR_DACCVIOL_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 1U) /*!< SCB CFSR (MMFSR): DACCVIOL Position */ +#define SCB_CFSR_DACCVIOL_Msk (1UL << SCB_CFSR_DACCVIOL_Pos) /*!< SCB CFSR (MMFSR): DACCVIOL Mask */ + +#define SCB_CFSR_IACCVIOL_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 0U) /*!< SCB CFSR (MMFSR): IACCVIOL Position */ +#define SCB_CFSR_IACCVIOL_Msk (1UL /*<< SCB_CFSR_IACCVIOL_Pos*/) /*!< SCB CFSR (MMFSR): IACCVIOL Mask */ + +/* BusFault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_BFARVALID_Pos (SCB_CFSR_BUSFAULTSR_Pos + 7U) /*!< SCB CFSR (BFSR): BFARVALID Position */ +#define SCB_CFSR_BFARVALID_Msk (1UL << SCB_CFSR_BFARVALID_Pos) /*!< SCB CFSR (BFSR): BFARVALID Mask */ + +#define SCB_CFSR_LSPERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 5U) /*!< SCB CFSR (BFSR): LSPERR Position */ +#define SCB_CFSR_LSPERR_Msk (1UL << SCB_CFSR_LSPERR_Pos) /*!< SCB CFSR (BFSR): LSPERR Mask */ + +#define SCB_CFSR_STKERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 4U) /*!< SCB CFSR (BFSR): STKERR Position */ +#define SCB_CFSR_STKERR_Msk (1UL << SCB_CFSR_STKERR_Pos) /*!< SCB CFSR (BFSR): STKERR Mask */ + +#define SCB_CFSR_UNSTKERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 3U) /*!< SCB CFSR (BFSR): UNSTKERR Position */ +#define SCB_CFSR_UNSTKERR_Msk (1UL << SCB_CFSR_UNSTKERR_Pos) /*!< SCB CFSR (BFSR): UNSTKERR Mask */ + +#define SCB_CFSR_IMPRECISERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 2U) /*!< SCB CFSR (BFSR): IMPRECISERR Position */ +#define SCB_CFSR_IMPRECISERR_Msk (1UL << SCB_CFSR_IMPRECISERR_Pos) /*!< SCB CFSR (BFSR): IMPRECISERR Mask */ + +#define SCB_CFSR_PRECISERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 1U) /*!< SCB CFSR (BFSR): PRECISERR Position */ +#define SCB_CFSR_PRECISERR_Msk (1UL << SCB_CFSR_PRECISERR_Pos) /*!< SCB CFSR (BFSR): PRECISERR Mask */ + +#define SCB_CFSR_IBUSERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 0U) /*!< SCB CFSR (BFSR): IBUSERR Position */ +#define SCB_CFSR_IBUSERR_Msk (1UL << SCB_CFSR_IBUSERR_Pos) /*!< SCB CFSR (BFSR): IBUSERR Mask */ + +/* UsageFault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_DIVBYZERO_Pos (SCB_CFSR_USGFAULTSR_Pos + 9U) /*!< SCB CFSR (UFSR): DIVBYZERO Position */ +#define SCB_CFSR_DIVBYZERO_Msk (1UL << SCB_CFSR_DIVBYZERO_Pos) /*!< SCB CFSR (UFSR): DIVBYZERO Mask */ + +#define SCB_CFSR_UNALIGNED_Pos (SCB_CFSR_USGFAULTSR_Pos + 8U) /*!< SCB CFSR (UFSR): UNALIGNED Position */ +#define SCB_CFSR_UNALIGNED_Msk (1UL << SCB_CFSR_UNALIGNED_Pos) /*!< SCB CFSR (UFSR): UNALIGNED Mask */ + +#define SCB_CFSR_STKOF_Pos (SCB_CFSR_USGFAULTSR_Pos + 4U) /*!< SCB CFSR (UFSR): STKOF Position */ +#define SCB_CFSR_STKOF_Msk (1UL << SCB_CFSR_STKOF_Pos) /*!< SCB CFSR (UFSR): STKOF Mask */ + +#define SCB_CFSR_NOCP_Pos (SCB_CFSR_USGFAULTSR_Pos + 3U) /*!< SCB CFSR (UFSR): NOCP Position */ +#define SCB_CFSR_NOCP_Msk (1UL << SCB_CFSR_NOCP_Pos) /*!< SCB CFSR (UFSR): NOCP Mask */ + +#define SCB_CFSR_INVPC_Pos (SCB_CFSR_USGFAULTSR_Pos + 2U) /*!< SCB CFSR (UFSR): INVPC Position */ +#define SCB_CFSR_INVPC_Msk (1UL << SCB_CFSR_INVPC_Pos) /*!< SCB CFSR (UFSR): INVPC Mask */ + +#define SCB_CFSR_INVSTATE_Pos (SCB_CFSR_USGFAULTSR_Pos + 1U) /*!< SCB CFSR (UFSR): INVSTATE Position */ +#define SCB_CFSR_INVSTATE_Msk (1UL << SCB_CFSR_INVSTATE_Pos) /*!< SCB CFSR (UFSR): INVSTATE Mask */ + +#define SCB_CFSR_UNDEFINSTR_Pos (SCB_CFSR_USGFAULTSR_Pos + 0U) /*!< SCB CFSR (UFSR): UNDEFINSTR Position */ +#define SCB_CFSR_UNDEFINSTR_Msk (1UL << SCB_CFSR_UNDEFINSTR_Pos) /*!< SCB CFSR (UFSR): UNDEFINSTR Mask */ + +/* SCB Hard Fault Status Register Definitions */ +#define SCB_HFSR_DEBUGEVT_Pos 31U /*!< SCB HFSR: DEBUGEVT Position */ +#define SCB_HFSR_DEBUGEVT_Msk (1UL << SCB_HFSR_DEBUGEVT_Pos) /*!< SCB HFSR: DEBUGEVT Mask */ + +#define SCB_HFSR_FORCED_Pos 30U /*!< SCB HFSR: FORCED Position */ +#define SCB_HFSR_FORCED_Msk (1UL << SCB_HFSR_FORCED_Pos) /*!< SCB HFSR: FORCED Mask */ + +#define SCB_HFSR_VECTTBL_Pos 1U /*!< SCB HFSR: VECTTBL Position */ +#define SCB_HFSR_VECTTBL_Msk (1UL << SCB_HFSR_VECTTBL_Pos) /*!< SCB HFSR: VECTTBL Mask */ + +/* SCB Debug Fault Status Register Definitions */ +#define SCB_DFSR_EXTERNAL_Pos 4U /*!< SCB DFSR: EXTERNAL Position */ +#define SCB_DFSR_EXTERNAL_Msk (1UL << SCB_DFSR_EXTERNAL_Pos) /*!< SCB DFSR: EXTERNAL Mask */ + +#define SCB_DFSR_VCATCH_Pos 3U /*!< SCB DFSR: VCATCH Position */ +#define SCB_DFSR_VCATCH_Msk (1UL << SCB_DFSR_VCATCH_Pos) /*!< SCB DFSR: VCATCH Mask */ + +#define SCB_DFSR_DWTTRAP_Pos 2U /*!< SCB DFSR: DWTTRAP Position */ +#define SCB_DFSR_DWTTRAP_Msk (1UL << SCB_DFSR_DWTTRAP_Pos) /*!< SCB DFSR: DWTTRAP Mask */ + +#define SCB_DFSR_BKPT_Pos 1U /*!< SCB DFSR: BKPT Position */ +#define SCB_DFSR_BKPT_Msk (1UL << SCB_DFSR_BKPT_Pos) /*!< SCB DFSR: BKPT Mask */ + +#define SCB_DFSR_HALTED_Pos 0U /*!< SCB DFSR: HALTED Position */ +#define SCB_DFSR_HALTED_Msk (1UL /*<< SCB_DFSR_HALTED_Pos*/) /*!< SCB DFSR: HALTED Mask */ + +/* SCB Non-Secure Access Control Register Definitions */ +#define SCB_NSACR_CP11_Pos 11U /*!< SCB NSACR: CP11 Position */ +#define SCB_NSACR_CP11_Msk (1UL << SCB_NSACR_CP11_Pos) /*!< SCB NSACR: CP11 Mask */ + +#define SCB_NSACR_CP10_Pos 10U /*!< SCB NSACR: CP10 Position */ +#define SCB_NSACR_CP10_Msk (1UL << SCB_NSACR_CP10_Pos) /*!< SCB NSACR: CP10 Mask */ + +#define SCB_NSACR_CPn_Pos 0U /*!< SCB NSACR: CPn Position */ +#define SCB_NSACR_CPn_Msk (1UL /*<< SCB_NSACR_CPn_Pos*/) /*!< SCB NSACR: CPn Mask */ + +/* SCB Cache Level ID Register Definitions */ +#define SCB_CLIDR_LOUU_Pos 27U /*!< SCB CLIDR: LoUU Position */ +#define SCB_CLIDR_LOUU_Msk (7UL << SCB_CLIDR_LOUU_Pos) /*!< SCB CLIDR: LoUU Mask */ + +#define SCB_CLIDR_LOC_Pos 24U /*!< SCB CLIDR: LoC Position */ +#define SCB_CLIDR_LOC_Msk (7UL << SCB_CLIDR_LOC_Pos) /*!< SCB CLIDR: LoC Mask */ + +/* SCB Cache Type Register Definitions */ +#define SCB_CTR_FORMAT_Pos 29U /*!< SCB CTR: Format Position */ +#define SCB_CTR_FORMAT_Msk (7UL << SCB_CTR_FORMAT_Pos) /*!< SCB CTR: Format Mask */ + +#define SCB_CTR_CWG_Pos 24U /*!< SCB CTR: CWG Position */ +#define SCB_CTR_CWG_Msk (0xFUL << SCB_CTR_CWG_Pos) /*!< SCB CTR: CWG Mask */ + +#define SCB_CTR_ERG_Pos 20U /*!< SCB CTR: ERG Position */ +#define SCB_CTR_ERG_Msk (0xFUL << SCB_CTR_ERG_Pos) /*!< SCB CTR: ERG Mask */ + +#define SCB_CTR_DMINLINE_Pos 16U /*!< SCB CTR: DminLine Position */ +#define SCB_CTR_DMINLINE_Msk (0xFUL << SCB_CTR_DMINLINE_Pos) /*!< SCB CTR: DminLine Mask */ + +#define SCB_CTR_IMINLINE_Pos 0U /*!< SCB CTR: ImInLine Position */ +#define SCB_CTR_IMINLINE_Msk (0xFUL /*<< SCB_CTR_IMINLINE_Pos*/) /*!< SCB CTR: ImInLine Mask */ + +/* SCB Cache Size ID Register Definitions */ +#define SCB_CCSIDR_WT_Pos 31U /*!< SCB CCSIDR: WT Position */ +#define SCB_CCSIDR_WT_Msk (1UL << SCB_CCSIDR_WT_Pos) /*!< SCB CCSIDR: WT Mask */ + +#define SCB_CCSIDR_WB_Pos 30U /*!< SCB CCSIDR: WB Position */ +#define SCB_CCSIDR_WB_Msk (1UL << SCB_CCSIDR_WB_Pos) /*!< SCB CCSIDR: WB Mask */ + +#define SCB_CCSIDR_RA_Pos 29U /*!< SCB CCSIDR: RA Position */ +#define SCB_CCSIDR_RA_Msk (1UL << SCB_CCSIDR_RA_Pos) /*!< SCB CCSIDR: RA Mask */ + +#define SCB_CCSIDR_WA_Pos 28U /*!< SCB CCSIDR: WA Position */ +#define SCB_CCSIDR_WA_Msk (1UL << SCB_CCSIDR_WA_Pos) /*!< SCB CCSIDR: WA Mask */ + +#define SCB_CCSIDR_NUMSETS_Pos 13U /*!< SCB CCSIDR: NumSets Position */ +#define SCB_CCSIDR_NUMSETS_Msk (0x7FFFUL << SCB_CCSIDR_NUMSETS_Pos) /*!< SCB CCSIDR: NumSets Mask */ + +#define SCB_CCSIDR_ASSOCIATIVITY_Pos 3U /*!< SCB CCSIDR: Associativity Position */ +#define SCB_CCSIDR_ASSOCIATIVITY_Msk (0x3FFUL << SCB_CCSIDR_ASSOCIATIVITY_Pos) /*!< SCB CCSIDR: Associativity Mask */ + +#define SCB_CCSIDR_LINESIZE_Pos 0U /*!< SCB CCSIDR: LineSize Position */ +#define SCB_CCSIDR_LINESIZE_Msk (7UL /*<< SCB_CCSIDR_LINESIZE_Pos*/) /*!< SCB CCSIDR: LineSize Mask */ + +/* SCB Cache Size Selection Register Definitions */ +#define SCB_CSSELR_LEVEL_Pos 1U /*!< SCB CSSELR: Level Position */ +#define SCB_CSSELR_LEVEL_Msk (7UL << SCB_CSSELR_LEVEL_Pos) /*!< SCB CSSELR: Level Mask */ + +#define SCB_CSSELR_IND_Pos 0U /*!< SCB CSSELR: InD Position */ +#define SCB_CSSELR_IND_Msk (1UL /*<< SCB_CSSELR_IND_Pos*/) /*!< SCB CSSELR: InD Mask */ + +/* SCB Software Triggered Interrupt Register Definitions */ +#define SCB_STIR_INTID_Pos 0U /*!< SCB STIR: INTID Position */ +#define SCB_STIR_INTID_Msk (0x1FFUL /*<< SCB_STIR_INTID_Pos*/) /*!< SCB STIR: INTID Mask */ + +/* SCB D-Cache Invalidate by Set-way Register Definitions */ +#define SCB_DCISW_WAY_Pos 30U /*!< SCB DCISW: Way Position */ +#define SCB_DCISW_WAY_Msk (3UL << SCB_DCISW_WAY_Pos) /*!< SCB DCISW: Way Mask */ + +#define SCB_DCISW_SET_Pos 5U /*!< SCB DCISW: Set Position */ +#define SCB_DCISW_SET_Msk (0x1FFUL << SCB_DCISW_SET_Pos) /*!< SCB DCISW: Set Mask */ + +/* SCB D-Cache Clean by Set-way Register Definitions */ +#define SCB_DCCSW_WAY_Pos 30U /*!< SCB DCCSW: Way Position */ +#define SCB_DCCSW_WAY_Msk (3UL << SCB_DCCSW_WAY_Pos) /*!< SCB DCCSW: Way Mask */ + +#define SCB_DCCSW_SET_Pos 5U /*!< SCB DCCSW: Set Position */ +#define SCB_DCCSW_SET_Msk (0x1FFUL << SCB_DCCSW_SET_Pos) /*!< SCB DCCSW: Set Mask */ + +/* SCB D-Cache Clean and Invalidate by Set-way Register Definitions */ +#define SCB_DCCISW_WAY_Pos 30U /*!< SCB DCCISW: Way Position */ +#define SCB_DCCISW_WAY_Msk (3UL << SCB_DCCISW_WAY_Pos) /*!< SCB DCCISW: Way Mask */ + +#define SCB_DCCISW_SET_Pos 5U /*!< SCB DCCISW: Set Position */ +#define SCB_DCCISW_SET_Msk (0x1FFUL << SCB_DCCISW_SET_Pos) /*!< SCB DCCISW: Set Mask */ + +/* Instruction Tightly-Coupled Memory Control Register Definitions */ +#define SCB_ITCMCR_SZ_Pos 3U /*!< SCB ITCMCR: SZ Position */ +#define SCB_ITCMCR_SZ_Msk (0xFUL << SCB_ITCMCR_SZ_Pos) /*!< SCB ITCMCR: SZ Mask */ + +#define SCB_ITCMCR_RETEN_Pos 2U /*!< SCB ITCMCR: RETEN Position */ +#define SCB_ITCMCR_RETEN_Msk (1UL << SCB_ITCMCR_RETEN_Pos) /*!< SCB ITCMCR: RETEN Mask */ + +#define SCB_ITCMCR_RMW_Pos 1U /*!< SCB ITCMCR: RMW Position */ +#define SCB_ITCMCR_RMW_Msk (1UL << SCB_ITCMCR_RMW_Pos) /*!< SCB ITCMCR: RMW Mask */ + +#define SCB_ITCMCR_EN_Pos 0U /*!< SCB ITCMCR: EN Position */ +#define SCB_ITCMCR_EN_Msk (1UL /*<< SCB_ITCMCR_EN_Pos*/) /*!< SCB ITCMCR: EN Mask */ + +/* Data Tightly-Coupled Memory Control Register Definitions */ +#define SCB_DTCMCR_SZ_Pos 3U /*!< SCB DTCMCR: SZ Position */ +#define SCB_DTCMCR_SZ_Msk (0xFUL << SCB_DTCMCR_SZ_Pos) /*!< SCB DTCMCR: SZ Mask */ + +#define SCB_DTCMCR_RETEN_Pos 2U /*!< SCB DTCMCR: RETEN Position */ +#define SCB_DTCMCR_RETEN_Msk (1UL << SCB_DTCMCR_RETEN_Pos) /*!< SCB DTCMCR: RETEN Mask */ + +#define SCB_DTCMCR_RMW_Pos 1U /*!< SCB DTCMCR: RMW Position */ +#define SCB_DTCMCR_RMW_Msk (1UL << SCB_DTCMCR_RMW_Pos) /*!< SCB DTCMCR: RMW Mask */ + +#define SCB_DTCMCR_EN_Pos 0U /*!< SCB DTCMCR: EN Position */ +#define SCB_DTCMCR_EN_Msk (1UL /*<< SCB_DTCMCR_EN_Pos*/) /*!< SCB DTCMCR: EN Mask */ + +/* AHBP Control Register Definitions */ +#define SCB_AHBPCR_SZ_Pos 1U /*!< SCB AHBPCR: SZ Position */ +#define SCB_AHBPCR_SZ_Msk (7UL << SCB_AHBPCR_SZ_Pos) /*!< SCB AHBPCR: SZ Mask */ + +#define SCB_AHBPCR_EN_Pos 0U /*!< SCB AHBPCR: EN Position */ +#define SCB_AHBPCR_EN_Msk (1UL /*<< SCB_AHBPCR_EN_Pos*/) /*!< SCB AHBPCR: EN Mask */ + +/* L1 Cache Control Register Definitions */ +#define SCB_CACR_FORCEWT_Pos 2U /*!< SCB CACR: FORCEWT Position */ +#define SCB_CACR_FORCEWT_Msk (1UL << SCB_CACR_FORCEWT_Pos) /*!< SCB CACR: FORCEWT Mask */ + +#define SCB_CACR_ECCEN_Pos 1U /*!< SCB CACR: ECCEN Position */ +#define SCB_CACR_ECCEN_Msk (1UL << SCB_CACR_ECCEN_Pos) /*!< SCB CACR: ECCEN Mask */ + +#define SCB_CACR_SIWT_Pos 0U /*!< SCB CACR: SIWT Position */ +#define SCB_CACR_SIWT_Msk (1UL /*<< SCB_CACR_SIWT_Pos*/) /*!< SCB CACR: SIWT Mask */ + +/* AHBS Control Register Definitions */ +#define SCB_AHBSCR_INITCOUNT_Pos 11U /*!< SCB AHBSCR: INITCOUNT Position */ +#define SCB_AHBSCR_INITCOUNT_Msk (0x1FUL << SCB_AHBPCR_INITCOUNT_Pos) /*!< SCB AHBSCR: INITCOUNT Mask */ + +#define SCB_AHBSCR_TPRI_Pos 2U /*!< SCB AHBSCR: TPRI Position */ +#define SCB_AHBSCR_TPRI_Msk (0x1FFUL << SCB_AHBPCR_TPRI_Pos) /*!< SCB AHBSCR: TPRI Mask */ + +#define SCB_AHBSCR_CTL_Pos 0U /*!< SCB AHBSCR: CTL Position*/ +#define SCB_AHBSCR_CTL_Msk (3UL /*<< SCB_AHBPCR_CTL_Pos*/) /*!< SCB AHBSCR: CTL Mask */ + +/* Auxiliary Bus Fault Status Register Definitions */ +#define SCB_ABFSR_AXIMTYPE_Pos 8U /*!< SCB ABFSR: AXIMTYPE Position*/ +#define SCB_ABFSR_AXIMTYPE_Msk (3UL << SCB_ABFSR_AXIMTYPE_Pos) /*!< SCB ABFSR: AXIMTYPE Mask */ + +#define SCB_ABFSR_EPPB_Pos 4U /*!< SCB ABFSR: EPPB Position*/ +#define SCB_ABFSR_EPPB_Msk (1UL << SCB_ABFSR_EPPB_Pos) /*!< SCB ABFSR: EPPB Mask */ + +#define SCB_ABFSR_AXIM_Pos 3U /*!< SCB ABFSR: AXIM Position*/ +#define SCB_ABFSR_AXIM_Msk (1UL << SCB_ABFSR_AXIM_Pos) /*!< SCB ABFSR: AXIM Mask */ + +#define SCB_ABFSR_AHBP_Pos 2U /*!< SCB ABFSR: AHBP Position*/ +#define SCB_ABFSR_AHBP_Msk (1UL << SCB_ABFSR_AHBP_Pos) /*!< SCB ABFSR: AHBP Mask */ + +#define SCB_ABFSR_DTCM_Pos 1U /*!< SCB ABFSR: DTCM Position*/ +#define SCB_ABFSR_DTCM_Msk (1UL << SCB_ABFSR_DTCM_Pos) /*!< SCB ABFSR: DTCM Mask */ + +#define SCB_ABFSR_ITCM_Pos 0U /*!< SCB ABFSR: ITCM Position*/ +#define SCB_ABFSR_ITCM_Msk (1UL /*<< SCB_ABFSR_ITCM_Pos*/) /*!< SCB ABFSR: ITCM Mask */ + +/*@} end of group CMSIS_SCB */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SCnSCB System Controls not in SCB (SCnSCB) + \brief Type definitions for the System Control and ID Register not in the SCB + @{ + */ + +/** + \brief Structure type to access the System Control and ID Register not in the SCB. + */ +typedef struct +{ + uint32_t RESERVED0[1U]; + __IM uint32_t ICTR; /*!< Offset: 0x004 (R/ ) Interrupt Controller Type Register */ + __IOM uint32_t ACTLR; /*!< Offset: 0x008 (R/W) Auxiliary Control Register */ + __IOM uint32_t CPPWR; /*!< Offset: 0x00C (R/W) Coprocessor Power Control Register */ +} SCnSCB_Type; + +/* Interrupt Controller Type Register Definitions */ +#define SCnSCB_ICTR_INTLINESNUM_Pos 0U /*!< ICTR: INTLINESNUM Position */ +#define SCnSCB_ICTR_INTLINESNUM_Msk (0xFUL /*<< SCnSCB_ICTR_INTLINESNUM_Pos*/) /*!< ICTR: INTLINESNUM Mask */ + +/*@} end of group CMSIS_SCnotSCB */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SysTick System Tick Timer (SysTick) + \brief Type definitions for the System Timer Registers. + @{ + */ + +/** + \brief Structure type to access the System Timer (SysTick). + */ +typedef struct +{ + __IOM uint32_t CTRL; /*!< Offset: 0x000 (R/W) SysTick Control and Status Register */ + __IOM uint32_t LOAD; /*!< Offset: 0x004 (R/W) SysTick Reload Value Register */ + __IOM uint32_t VAL; /*!< Offset: 0x008 (R/W) SysTick Current Value Register */ + __IM uint32_t CALIB; /*!< Offset: 0x00C (R/ ) SysTick Calibration Register */ +} SysTick_Type; + +/* SysTick Control / Status Register Definitions */ +#define SysTick_CTRL_COUNTFLAG_Pos 16U /*!< SysTick CTRL: COUNTFLAG Position */ +#define SysTick_CTRL_COUNTFLAG_Msk (1UL << SysTick_CTRL_COUNTFLAG_Pos) /*!< SysTick CTRL: COUNTFLAG Mask */ + +#define SysTick_CTRL_CLKSOURCE_Pos 2U /*!< SysTick CTRL: CLKSOURCE Position */ +#define SysTick_CTRL_CLKSOURCE_Msk (1UL << SysTick_CTRL_CLKSOURCE_Pos) /*!< SysTick CTRL: CLKSOURCE Mask */ + +#define SysTick_CTRL_TICKINT_Pos 1U /*!< SysTick CTRL: TICKINT Position */ +#define SysTick_CTRL_TICKINT_Msk (1UL << SysTick_CTRL_TICKINT_Pos) /*!< SysTick CTRL: TICKINT Mask */ + +#define SysTick_CTRL_ENABLE_Pos 0U /*!< SysTick CTRL: ENABLE Position */ +#define SysTick_CTRL_ENABLE_Msk (1UL /*<< SysTick_CTRL_ENABLE_Pos*/) /*!< SysTick CTRL: ENABLE Mask */ + +/* SysTick Reload Register Definitions */ +#define SysTick_LOAD_RELOAD_Pos 0U /*!< SysTick LOAD: RELOAD Position */ +#define SysTick_LOAD_RELOAD_Msk (0xFFFFFFUL /*<< SysTick_LOAD_RELOAD_Pos*/) /*!< SysTick LOAD: RELOAD Mask */ + +/* SysTick Current Register Definitions */ +#define SysTick_VAL_CURRENT_Pos 0U /*!< SysTick VAL: CURRENT Position */ +#define SysTick_VAL_CURRENT_Msk (0xFFFFFFUL /*<< SysTick_VAL_CURRENT_Pos*/) /*!< SysTick VAL: CURRENT Mask */ + +/* SysTick Calibration Register Definitions */ +#define SysTick_CALIB_NOREF_Pos 31U /*!< SysTick CALIB: NOREF Position */ +#define SysTick_CALIB_NOREF_Msk (1UL << SysTick_CALIB_NOREF_Pos) /*!< SysTick CALIB: NOREF Mask */ + +#define SysTick_CALIB_SKEW_Pos 30U /*!< SysTick CALIB: SKEW Position */ +#define SysTick_CALIB_SKEW_Msk (1UL << SysTick_CALIB_SKEW_Pos) /*!< SysTick CALIB: SKEW Mask */ + +#define SysTick_CALIB_TENMS_Pos 0U /*!< SysTick CALIB: TENMS Position */ +#define SysTick_CALIB_TENMS_Msk (0xFFFFFFUL /*<< SysTick_CALIB_TENMS_Pos*/) /*!< SysTick CALIB: TENMS Mask */ + +/*@} end of group CMSIS_SysTick */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_ITM Instrumentation Trace Macrocell (ITM) + \brief Type definitions for the Instrumentation Trace Macrocell (ITM) + @{ + */ + +/** + \brief Structure type to access the Instrumentation Trace Macrocell Register (ITM). + */ +typedef struct +{ + __OM union + { + __OM uint8_t u8; /*!< Offset: 0x000 ( /W) ITM Stimulus Port 8-bit */ + __OM uint16_t u16; /*!< Offset: 0x000 ( /W) ITM Stimulus Port 16-bit */ + __OM uint32_t u32; /*!< Offset: 0x000 ( /W) ITM Stimulus Port 32-bit */ + } PORT [32U]; /*!< Offset: 0x000 ( /W) ITM Stimulus Port Registers */ + uint32_t RESERVED0[864U]; + __IOM uint32_t TER; /*!< Offset: 0xE00 (R/W) ITM Trace Enable Register */ + uint32_t RESERVED1[15U]; + __IOM uint32_t TPR; /*!< Offset: 0xE40 (R/W) ITM Trace Privilege Register */ + uint32_t RESERVED2[15U]; + __IOM uint32_t TCR; /*!< Offset: 0xE80 (R/W) ITM Trace Control Register */ + uint32_t RESERVED3[29U]; + __OM uint32_t IWR; /*!< Offset: 0xEF8 ( /W) ITM Integration Write Register */ + __IM uint32_t IRR; /*!< Offset: 0xEFC (R/ ) ITM Integration Read Register */ + __IOM uint32_t IMCR; /*!< Offset: 0xF00 (R/W) ITM Integration Mode Control Register */ + uint32_t RESERVED4[43U]; + __OM uint32_t LAR; /*!< Offset: 0xFB0 ( /W) ITM Lock Access Register */ + __IM uint32_t LSR; /*!< Offset: 0xFB4 (R/ ) ITM Lock Status Register */ + uint32_t RESERVED5[1U]; + __IM uint32_t DEVARCH; /*!< Offset: 0xFBC (R/ ) ITM Device Architecture Register */ + uint32_t RESERVED6[4U]; + __IM uint32_t PID4; /*!< Offset: 0xFD0 (R/ ) ITM Peripheral Identification Register #4 */ + __IM uint32_t PID5; /*!< Offset: 0xFD4 (R/ ) ITM Peripheral Identification Register #5 */ + __IM uint32_t PID6; /*!< Offset: 0xFD8 (R/ ) ITM Peripheral Identification Register #6 */ + __IM uint32_t PID7; /*!< Offset: 0xFDC (R/ ) ITM Peripheral Identification Register #7 */ + __IM uint32_t PID0; /*!< Offset: 0xFE0 (R/ ) ITM Peripheral Identification Register #0 */ + __IM uint32_t PID1; /*!< Offset: 0xFE4 (R/ ) ITM Peripheral Identification Register #1 */ + __IM uint32_t PID2; /*!< Offset: 0xFE8 (R/ ) ITM Peripheral Identification Register #2 */ + __IM uint32_t PID3; /*!< Offset: 0xFEC (R/ ) ITM Peripheral Identification Register #3 */ + __IM uint32_t CID0; /*!< Offset: 0xFF0 (R/ ) ITM Component Identification Register #0 */ + __IM uint32_t CID1; /*!< Offset: 0xFF4 (R/ ) ITM Component Identification Register #1 */ + __IM uint32_t CID2; /*!< Offset: 0xFF8 (R/ ) ITM Component Identification Register #2 */ + __IM uint32_t CID3; /*!< Offset: 0xFFC (R/ ) ITM Component Identification Register #3 */ +} ITM_Type; + +/* ITM Stimulus Port Register Definitions */ +#define ITM_STIM_DISABLED_Pos 1U /*!< ITM STIM: DISABLED Position */ +#define ITM_STIM_DISABLED_Msk (0x1UL << ITM_STIM_DISABLED_Pos) /*!< ITM STIM: DISABLED Mask */ + +#define ITM_STIM_FIFOREADY_Pos 0U /*!< ITM STIM: FIFOREADY Position */ +#define ITM_STIM_FIFOREADY_Msk (0x1UL /*<< ITM_STIM_FIFOREADY_Pos*/) /*!< ITM STIM: FIFOREADY Mask */ + +/* ITM Trace Privilege Register Definitions */ +#define ITM_TPR_PRIVMASK_Pos 0U /*!< ITM TPR: PRIVMASK Position */ +#define ITM_TPR_PRIVMASK_Msk (0xFFFFFFFFUL /*<< ITM_TPR_PRIVMASK_Pos*/) /*!< ITM TPR: PRIVMASK Mask */ + +/* ITM Trace Control Register Definitions */ +#define ITM_TCR_BUSY_Pos 23U /*!< ITM TCR: BUSY Position */ +#define ITM_TCR_BUSY_Msk (1UL << ITM_TCR_BUSY_Pos) /*!< ITM TCR: BUSY Mask */ + +#define ITM_TCR_TRACEBUSID_Pos 16U /*!< ITM TCR: ATBID Position */ +#define ITM_TCR_TRACEBUSID_Msk (0x7FUL << ITM_TCR_TRACEBUSID_Pos) /*!< ITM TCR: ATBID Mask */ + +#define ITM_TCR_GTSFREQ_Pos 10U /*!< ITM TCR: Global timestamp frequency Position */ +#define ITM_TCR_GTSFREQ_Msk (3UL << ITM_TCR_GTSFREQ_Pos) /*!< ITM TCR: Global timestamp frequency Mask */ + +#define ITM_TCR_TSPRESCALE_Pos 8U /*!< ITM TCR: TSPRESCALE Position */ +#define ITM_TCR_TSPRESCALE_Msk (3UL << ITM_TCR_TSPRESCALE_Pos) /*!< ITM TCR: TSPRESCALE Mask */ + +#define ITM_TCR_STALLENA_Pos 5U /*!< ITM TCR: STALLENA Position */ +#define ITM_TCR_STALLENA_Msk (1UL << ITM_TCR_STALLENA_Pos) /*!< ITM TCR: STALLENA Mask */ + +#define ITM_TCR_SWOENA_Pos 4U /*!< ITM TCR: SWOENA Position */ +#define ITM_TCR_SWOENA_Msk (1UL << ITM_TCR_SWOENA_Pos) /*!< ITM TCR: SWOENA Mask */ + +#define ITM_TCR_DWTENA_Pos 3U /*!< ITM TCR: DWTENA Position */ +#define ITM_TCR_DWTENA_Msk (1UL << ITM_TCR_DWTENA_Pos) /*!< ITM TCR: DWTENA Mask */ + +#define ITM_TCR_SYNCENA_Pos 2U /*!< ITM TCR: SYNCENA Position */ +#define ITM_TCR_SYNCENA_Msk (1UL << ITM_TCR_SYNCENA_Pos) /*!< ITM TCR: SYNCENA Mask */ + +#define ITM_TCR_TSENA_Pos 1U /*!< ITM TCR: TSENA Position */ +#define ITM_TCR_TSENA_Msk (1UL << ITM_TCR_TSENA_Pos) /*!< ITM TCR: TSENA Mask */ + +#define ITM_TCR_ITMENA_Pos 0U /*!< ITM TCR: ITM Enable bit Position */ +#define ITM_TCR_ITMENA_Msk (1UL /*<< ITM_TCR_ITMENA_Pos*/) /*!< ITM TCR: ITM Enable bit Mask */ + +/* ITM Integration Write Register Definitions */ +#define ITM_IWR_ATVALIDM_Pos 0U /*!< ITM IWR: ATVALIDM Position */ +#define ITM_IWR_ATVALIDM_Msk (1UL /*<< ITM_IWR_ATVALIDM_Pos*/) /*!< ITM IWR: ATVALIDM Mask */ + +/* ITM Integration Read Register Definitions */ +#define ITM_IRR_ATREADYM_Pos 0U /*!< ITM IRR: ATREADYM Position */ +#define ITM_IRR_ATREADYM_Msk (1UL /*<< ITM_IRR_ATREADYM_Pos*/) /*!< ITM IRR: ATREADYM Mask */ + +/* ITM Integration Mode Control Register Definitions */ +#define ITM_IMCR_INTEGRATION_Pos 0U /*!< ITM IMCR: INTEGRATION Position */ +#define ITM_IMCR_INTEGRATION_Msk (1UL /*<< ITM_IMCR_INTEGRATION_Pos*/) /*!< ITM IMCR: INTEGRATION Mask */ + +/* ITM Lock Status Register Definitions */ +#define ITM_LSR_ByteAcc_Pos 2U /*!< ITM LSR: ByteAcc Position */ +#define ITM_LSR_ByteAcc_Msk (1UL << ITM_LSR_ByteAcc_Pos) /*!< ITM LSR: ByteAcc Mask */ + +#define ITM_LSR_Access_Pos 1U /*!< ITM LSR: Access Position */ +#define ITM_LSR_Access_Msk (1UL << ITM_LSR_Access_Pos) /*!< ITM LSR: Access Mask */ + +#define ITM_LSR_Present_Pos 0U /*!< ITM LSR: Present Position */ +#define ITM_LSR_Present_Msk (1UL /*<< ITM_LSR_Present_Pos*/) /*!< ITM LSR: Present Mask */ + +/*@}*/ /* end of group CMSIS_ITM */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_DWT Data Watchpoint and Trace (DWT) + \brief Type definitions for the Data Watchpoint and Trace (DWT) + @{ + */ + +/** + \brief Structure type to access the Data Watchpoint and Trace Register (DWT). + */ +typedef struct +{ + __IOM uint32_t CTRL; /*!< Offset: 0x000 (R/W) Control Register */ + __IOM uint32_t CYCCNT; /*!< Offset: 0x004 (R/W) Cycle Count Register */ + __IOM uint32_t CPICNT; /*!< Offset: 0x008 (R/W) CPI Count Register */ + __IOM uint32_t EXCCNT; /*!< Offset: 0x00C (R/W) Exception Overhead Count Register */ + __IOM uint32_t SLEEPCNT; /*!< Offset: 0x010 (R/W) Sleep Count Register */ + __IOM uint32_t LSUCNT; /*!< Offset: 0x014 (R/W) LSU Count Register */ + __IOM uint32_t FOLDCNT; /*!< Offset: 0x018 (R/W) Folded-instruction Count Register */ + __IM uint32_t PCSR; /*!< Offset: 0x01C (R/ ) Program Counter Sample Register */ + __IOM uint32_t COMP0; /*!< Offset: 0x020 (R/W) Comparator Register 0 */ + uint32_t RESERVED1[1U]; + __IOM uint32_t FUNCTION0; /*!< Offset: 0x028 (R/W) Function Register 0 */ + uint32_t RESERVED2[1U]; + __IOM uint32_t COMP1; /*!< Offset: 0x030 (R/W) Comparator Register 1 */ + uint32_t RESERVED3[1U]; + __IOM uint32_t FUNCTION1; /*!< Offset: 0x038 (R/W) Function Register 1 */ + uint32_t RESERVED4[1U]; + __IOM uint32_t COMP2; /*!< Offset: 0x040 (R/W) Comparator Register 2 */ + uint32_t RESERVED5[1U]; + __IOM uint32_t FUNCTION2; /*!< Offset: 0x048 (R/W) Function Register 2 */ + uint32_t RESERVED6[1U]; + __IOM uint32_t COMP3; /*!< Offset: 0x050 (R/W) Comparator Register 3 */ + uint32_t RESERVED7[1U]; + __IOM uint32_t FUNCTION3; /*!< Offset: 0x058 (R/W) Function Register 3 */ + uint32_t RESERVED8[1U]; + __IOM uint32_t COMP4; /*!< Offset: 0x060 (R/W) Comparator Register 4 */ + uint32_t RESERVED9[1U]; + __IOM uint32_t FUNCTION4; /*!< Offset: 0x068 (R/W) Function Register 4 */ + uint32_t RESERVED10[1U]; + __IOM uint32_t COMP5; /*!< Offset: 0x070 (R/W) Comparator Register 5 */ + uint32_t RESERVED11[1U]; + __IOM uint32_t FUNCTION5; /*!< Offset: 0x078 (R/W) Function Register 5 */ + uint32_t RESERVED12[1U]; + __IOM uint32_t COMP6; /*!< Offset: 0x080 (R/W) Comparator Register 6 */ + uint32_t RESERVED13[1U]; + __IOM uint32_t FUNCTION6; /*!< Offset: 0x088 (R/W) Function Register 6 */ + uint32_t RESERVED14[1U]; + __IOM uint32_t COMP7; /*!< Offset: 0x090 (R/W) Comparator Register 7 */ + uint32_t RESERVED15[1U]; + __IOM uint32_t FUNCTION7; /*!< Offset: 0x098 (R/W) Function Register 7 */ + uint32_t RESERVED16[1U]; + __IOM uint32_t COMP8; /*!< Offset: 0x0A0 (R/W) Comparator Register 8 */ + uint32_t RESERVED17[1U]; + __IOM uint32_t FUNCTION8; /*!< Offset: 0x0A8 (R/W) Function Register 8 */ + uint32_t RESERVED18[1U]; + __IOM uint32_t COMP9; /*!< Offset: 0x0B0 (R/W) Comparator Register 9 */ + uint32_t RESERVED19[1U]; + __IOM uint32_t FUNCTION9; /*!< Offset: 0x0B8 (R/W) Function Register 9 */ + uint32_t RESERVED20[1U]; + __IOM uint32_t COMP10; /*!< Offset: 0x0C0 (R/W) Comparator Register 10 */ + uint32_t RESERVED21[1U]; + __IOM uint32_t FUNCTION10; /*!< Offset: 0x0C8 (R/W) Function Register 10 */ + uint32_t RESERVED22[1U]; + __IOM uint32_t COMP11; /*!< Offset: 0x0D0 (R/W) Comparator Register 11 */ + uint32_t RESERVED23[1U]; + __IOM uint32_t FUNCTION11; /*!< Offset: 0x0D8 (R/W) Function Register 11 */ + uint32_t RESERVED24[1U]; + __IOM uint32_t COMP12; /*!< Offset: 0x0E0 (R/W) Comparator Register 12 */ + uint32_t RESERVED25[1U]; + __IOM uint32_t FUNCTION12; /*!< Offset: 0x0E8 (R/W) Function Register 12 */ + uint32_t RESERVED26[1U]; + __IOM uint32_t COMP13; /*!< Offset: 0x0F0 (R/W) Comparator Register 13 */ + uint32_t RESERVED27[1U]; + __IOM uint32_t FUNCTION13; /*!< Offset: 0x0F8 (R/W) Function Register 13 */ + uint32_t RESERVED28[1U]; + __IOM uint32_t COMP14; /*!< Offset: 0x100 (R/W) Comparator Register 14 */ + uint32_t RESERVED29[1U]; + __IOM uint32_t FUNCTION14; /*!< Offset: 0x108 (R/W) Function Register 14 */ + uint32_t RESERVED30[1U]; + __IOM uint32_t COMP15; /*!< Offset: 0x110 (R/W) Comparator Register 15 */ + uint32_t RESERVED31[1U]; + __IOM uint32_t FUNCTION15; /*!< Offset: 0x118 (R/W) Function Register 15 */ + uint32_t RESERVED32[934U]; + __IM uint32_t LSR; /*!< Offset: 0xFB4 (R ) Lock Status Register */ + uint32_t RESERVED33[1U]; + __IM uint32_t DEVARCH; /*!< Offset: 0xFBC (R/ ) Device Architecture Register */ +} DWT_Type; + +/* DWT Control Register Definitions */ +#define DWT_CTRL_NUMCOMP_Pos 28U /*!< DWT CTRL: NUMCOMP Position */ +#define DWT_CTRL_NUMCOMP_Msk (0xFUL << DWT_CTRL_NUMCOMP_Pos) /*!< DWT CTRL: NUMCOMP Mask */ + +#define DWT_CTRL_NOTRCPKT_Pos 27U /*!< DWT CTRL: NOTRCPKT Position */ +#define DWT_CTRL_NOTRCPKT_Msk (0x1UL << DWT_CTRL_NOTRCPKT_Pos) /*!< DWT CTRL: NOTRCPKT Mask */ + +#define DWT_CTRL_NOEXTTRIG_Pos 26U /*!< DWT CTRL: NOEXTTRIG Position */ +#define DWT_CTRL_NOEXTTRIG_Msk (0x1UL << DWT_CTRL_NOEXTTRIG_Pos) /*!< DWT CTRL: NOEXTTRIG Mask */ + +#define DWT_CTRL_NOCYCCNT_Pos 25U /*!< DWT CTRL: NOCYCCNT Position */ +#define DWT_CTRL_NOCYCCNT_Msk (0x1UL << DWT_CTRL_NOCYCCNT_Pos) /*!< DWT CTRL: NOCYCCNT Mask */ + +#define DWT_CTRL_NOPRFCNT_Pos 24U /*!< DWT CTRL: NOPRFCNT Position */ +#define DWT_CTRL_NOPRFCNT_Msk (0x1UL << DWT_CTRL_NOPRFCNT_Pos) /*!< DWT CTRL: NOPRFCNT Mask */ + +#define DWT_CTRL_CYCDISS_Pos 23U /*!< DWT CTRL: CYCDISS Position */ +#define DWT_CTRL_CYCDISS_Msk (0x1UL << DWT_CTRL_CYCDISS_Pos) /*!< DWT CTRL: CYCDISS Mask */ + +#define DWT_CTRL_CYCEVTENA_Pos 22U /*!< DWT CTRL: CYCEVTENA Position */ +#define DWT_CTRL_CYCEVTENA_Msk (0x1UL << DWT_CTRL_CYCEVTENA_Pos) /*!< DWT CTRL: CYCEVTENA Mask */ + +#define DWT_CTRL_FOLDEVTENA_Pos 21U /*!< DWT CTRL: FOLDEVTENA Position */ +#define DWT_CTRL_FOLDEVTENA_Msk (0x1UL << DWT_CTRL_FOLDEVTENA_Pos) /*!< DWT CTRL: FOLDEVTENA Mask */ + +#define DWT_CTRL_LSUEVTENA_Pos 20U /*!< DWT CTRL: LSUEVTENA Position */ +#define DWT_CTRL_LSUEVTENA_Msk (0x1UL << DWT_CTRL_LSUEVTENA_Pos) /*!< DWT CTRL: LSUEVTENA Mask */ + +#define DWT_CTRL_SLEEPEVTENA_Pos 19U /*!< DWT CTRL: SLEEPEVTENA Position */ +#define DWT_CTRL_SLEEPEVTENA_Msk (0x1UL << DWT_CTRL_SLEEPEVTENA_Pos) /*!< DWT CTRL: SLEEPEVTENA Mask */ + +#define DWT_CTRL_EXCEVTENA_Pos 18U /*!< DWT CTRL: EXCEVTENA Position */ +#define DWT_CTRL_EXCEVTENA_Msk (0x1UL << DWT_CTRL_EXCEVTENA_Pos) /*!< DWT CTRL: EXCEVTENA Mask */ + +#define DWT_CTRL_CPIEVTENA_Pos 17U /*!< DWT CTRL: CPIEVTENA Position */ +#define DWT_CTRL_CPIEVTENA_Msk (0x1UL << DWT_CTRL_CPIEVTENA_Pos) /*!< DWT CTRL: CPIEVTENA Mask */ + +#define DWT_CTRL_EXCTRCENA_Pos 16U /*!< DWT CTRL: EXCTRCENA Position */ +#define DWT_CTRL_EXCTRCENA_Msk (0x1UL << DWT_CTRL_EXCTRCENA_Pos) /*!< DWT CTRL: EXCTRCENA Mask */ + +#define DWT_CTRL_PCSAMPLENA_Pos 12U /*!< DWT CTRL: PCSAMPLENA Position */ +#define DWT_CTRL_PCSAMPLENA_Msk (0x1UL << DWT_CTRL_PCSAMPLENA_Pos) /*!< DWT CTRL: PCSAMPLENA Mask */ + +#define DWT_CTRL_SYNCTAP_Pos 10U /*!< DWT CTRL: SYNCTAP Position */ +#define DWT_CTRL_SYNCTAP_Msk (0x3UL << DWT_CTRL_SYNCTAP_Pos) /*!< DWT CTRL: SYNCTAP Mask */ + +#define DWT_CTRL_CYCTAP_Pos 9U /*!< DWT CTRL: CYCTAP Position */ +#define DWT_CTRL_CYCTAP_Msk (0x1UL << DWT_CTRL_CYCTAP_Pos) /*!< DWT CTRL: CYCTAP Mask */ + +#define DWT_CTRL_POSTINIT_Pos 5U /*!< DWT CTRL: POSTINIT Position */ +#define DWT_CTRL_POSTINIT_Msk (0xFUL << DWT_CTRL_POSTINIT_Pos) /*!< DWT CTRL: POSTINIT Mask */ + +#define DWT_CTRL_POSTPRESET_Pos 1U /*!< DWT CTRL: POSTPRESET Position */ +#define DWT_CTRL_POSTPRESET_Msk (0xFUL << DWT_CTRL_POSTPRESET_Pos) /*!< DWT CTRL: POSTPRESET Mask */ + +#define DWT_CTRL_CYCCNTENA_Pos 0U /*!< DWT CTRL: CYCCNTENA Position */ +#define DWT_CTRL_CYCCNTENA_Msk (0x1UL /*<< DWT_CTRL_CYCCNTENA_Pos*/) /*!< DWT CTRL: CYCCNTENA Mask */ + +/* DWT CPI Count Register Definitions */ +#define DWT_CPICNT_CPICNT_Pos 0U /*!< DWT CPICNT: CPICNT Position */ +#define DWT_CPICNT_CPICNT_Msk (0xFFUL /*<< DWT_CPICNT_CPICNT_Pos*/) /*!< DWT CPICNT: CPICNT Mask */ + +/* DWT Exception Overhead Count Register Definitions */ +#define DWT_EXCCNT_EXCCNT_Pos 0U /*!< DWT EXCCNT: EXCCNT Position */ +#define DWT_EXCCNT_EXCCNT_Msk (0xFFUL /*<< DWT_EXCCNT_EXCCNT_Pos*/) /*!< DWT EXCCNT: EXCCNT Mask */ + +/* DWT Sleep Count Register Definitions */ +#define DWT_SLEEPCNT_SLEEPCNT_Pos 0U /*!< DWT SLEEPCNT: SLEEPCNT Position */ +#define DWT_SLEEPCNT_SLEEPCNT_Msk (0xFFUL /*<< DWT_SLEEPCNT_SLEEPCNT_Pos*/) /*!< DWT SLEEPCNT: SLEEPCNT Mask */ + +/* DWT LSU Count Register Definitions */ +#define DWT_LSUCNT_LSUCNT_Pos 0U /*!< DWT LSUCNT: LSUCNT Position */ +#define DWT_LSUCNT_LSUCNT_Msk (0xFFUL /*<< DWT_LSUCNT_LSUCNT_Pos*/) /*!< DWT LSUCNT: LSUCNT Mask */ + +/* DWT Folded-instruction Count Register Definitions */ +#define DWT_FOLDCNT_FOLDCNT_Pos 0U /*!< DWT FOLDCNT: FOLDCNT Position */ +#define DWT_FOLDCNT_FOLDCNT_Msk (0xFFUL /*<< DWT_FOLDCNT_FOLDCNT_Pos*/) /*!< DWT FOLDCNT: FOLDCNT Mask */ + +/* DWT Comparator Function Register Definitions */ +#define DWT_FUNCTION_ID_Pos 27U /*!< DWT FUNCTION: ID Position */ +#define DWT_FUNCTION_ID_Msk (0x1FUL << DWT_FUNCTION_ID_Pos) /*!< DWT FUNCTION: ID Mask */ + +#define DWT_FUNCTION_MATCHED_Pos 24U /*!< DWT FUNCTION: MATCHED Position */ +#define DWT_FUNCTION_MATCHED_Msk (0x1UL << DWT_FUNCTION_MATCHED_Pos) /*!< DWT FUNCTION: MATCHED Mask */ + +#define DWT_FUNCTION_DATAVSIZE_Pos 10U /*!< DWT FUNCTION: DATAVSIZE Position */ +#define DWT_FUNCTION_DATAVSIZE_Msk (0x3UL << DWT_FUNCTION_DATAVSIZE_Pos) /*!< DWT FUNCTION: DATAVSIZE Mask */ + +#define DWT_FUNCTION_ACTION_Pos 4U /*!< DWT FUNCTION: ACTION Position */ +#define DWT_FUNCTION_ACTION_Msk (0x1UL << DWT_FUNCTION_ACTION_Pos) /*!< DWT FUNCTION: ACTION Mask */ + +#define DWT_FUNCTION_MATCH_Pos 0U /*!< DWT FUNCTION: MATCH Position */ +#define DWT_FUNCTION_MATCH_Msk (0xFUL /*<< DWT_FUNCTION_MATCH_Pos*/) /*!< DWT FUNCTION: MATCH Mask */ + +/*@}*/ /* end of group CMSIS_DWT */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_TPI Trace Port Interface (TPI) + \brief Type definitions for the Trace Port Interface (TPI) + @{ + */ + +/** + \brief Structure type to access the Trace Port Interface Register (TPI). + */ +typedef struct +{ + __IM uint32_t SSPSR; /*!< Offset: 0x000 (R/ ) Supported Parallel Port Size Register */ + __IOM uint32_t CSPSR; /*!< Offset: 0x004 (R/W) Current Parallel Port Size Register */ + uint32_t RESERVED0[2U]; + __IOM uint32_t ACPR; /*!< Offset: 0x010 (R/W) Asynchronous Clock Prescaler Register */ + uint32_t RESERVED1[55U]; + __IOM uint32_t SPPR; /*!< Offset: 0x0F0 (R/W) Selected Pin Protocol Register */ + uint32_t RESERVED2[131U]; + __IM uint32_t FFSR; /*!< Offset: 0x300 (R/ ) Formatter and Flush Status Register */ + __IOM uint32_t FFCR; /*!< Offset: 0x304 (R/W) Formatter and Flush Control Register */ + __IOM uint32_t PSCR; /*!< Offset: 0x308 (R/W) Periodic Synchronization Control Register */ + uint32_t RESERVED3[759U]; + __IM uint32_t TRIGGER; /*!< Offset: 0xEE8 (R/ ) TRIGGER Register */ + __IM uint32_t ITFTTD0; /*!< Offset: 0xEEC (R/ ) Integration Test FIFO Test Data 0 Register */ + __IOM uint32_t ITATBCTR2; /*!< Offset: 0xEF0 (R/W) Integration Test ATB Control Register 2 */ + uint32_t RESERVED4[1U]; + __IM uint32_t ITATBCTR0; /*!< Offset: 0xEF8 (R/ ) Integration Test ATB Control Register 0 */ + __IM uint32_t ITFTTD1; /*!< Offset: 0xEFC (R/ ) Integration Test FIFO Test Data 1 Register */ + __IOM uint32_t ITCTRL; /*!< Offset: 0xF00 (R/W) Integration Mode Control */ + uint32_t RESERVED5[39U]; + __IOM uint32_t CLAIMSET; /*!< Offset: 0xFA0 (R/W) Claim tag set */ + __IOM uint32_t CLAIMCLR; /*!< Offset: 0xFA4 (R/W) Claim tag clear */ + uint32_t RESERVED7[8U]; + __IM uint32_t DEVID; /*!< Offset: 0xFC8 (R/ ) Device Configuration Register */ + __IM uint32_t DEVTYPE; /*!< Offset: 0xFCC (R/ ) Device Type Identifier Register */ +} TPI_Type; + +/* TPI Asynchronous Clock Prescaler Register Definitions */ +#define TPI_ACPR_PRESCALER_Pos 0U /*!< TPI ACPR: PRESCALER Position */ +#define TPI_ACPR_PRESCALER_Msk (0x1FFFUL /*<< TPI_ACPR_PRESCALER_Pos*/) /*!< TPI ACPR: PRESCALER Mask */ + +/* TPI Selected Pin Protocol Register Definitions */ +#define TPI_SPPR_TXMODE_Pos 0U /*!< TPI SPPR: TXMODE Position */ +#define TPI_SPPR_TXMODE_Msk (0x3UL /*<< TPI_SPPR_TXMODE_Pos*/) /*!< TPI SPPR: TXMODE Mask */ + +/* TPI Formatter and Flush Status Register Definitions */ +#define TPI_FFSR_FtNonStop_Pos 3U /*!< TPI FFSR: FtNonStop Position */ +#define TPI_FFSR_FtNonStop_Msk (0x1UL << TPI_FFSR_FtNonStop_Pos) /*!< TPI FFSR: FtNonStop Mask */ + +#define TPI_FFSR_TCPresent_Pos 2U /*!< TPI FFSR: TCPresent Position */ +#define TPI_FFSR_TCPresent_Msk (0x1UL << TPI_FFSR_TCPresent_Pos) /*!< TPI FFSR: TCPresent Mask */ + +#define TPI_FFSR_FtStopped_Pos 1U /*!< TPI FFSR: FtStopped Position */ +#define TPI_FFSR_FtStopped_Msk (0x1UL << TPI_FFSR_FtStopped_Pos) /*!< TPI FFSR: FtStopped Mask */ + +#define TPI_FFSR_FlInProg_Pos 0U /*!< TPI FFSR: FlInProg Position */ +#define TPI_FFSR_FlInProg_Msk (0x1UL /*<< TPI_FFSR_FlInProg_Pos*/) /*!< TPI FFSR: FlInProg Mask */ + +/* TPI Formatter and Flush Control Register Definitions */ +#define TPI_FFCR_TrigIn_Pos 8U /*!< TPI FFCR: TrigIn Position */ +#define TPI_FFCR_TrigIn_Msk (0x1UL << TPI_FFCR_TrigIn_Pos) /*!< TPI FFCR: TrigIn Mask */ + +#define TPI_FFCR_FOnMan_Pos 6U /*!< TPI FFCR: FOnMan Position */ +#define TPI_FFCR_FOnMan_Msk (0x1UL << TPI_FFCR_FOnMan_Pos) /*!< TPI FFCR: FOnMan Mask */ + +#define TPI_FFCR_EnFCont_Pos 1U /*!< TPI FFCR: EnFCont Position */ +#define TPI_FFCR_EnFCont_Msk (0x1UL << TPI_FFCR_EnFCont_Pos) /*!< TPI FFCR: EnFCont Mask */ + +/* TPI TRIGGER Register Definitions */ +#define TPI_TRIGGER_TRIGGER_Pos 0U /*!< TPI TRIGGER: TRIGGER Position */ +#define TPI_TRIGGER_TRIGGER_Msk (0x1UL /*<< TPI_TRIGGER_TRIGGER_Pos*/) /*!< TPI TRIGGER: TRIGGER Mask */ + +/* TPI Integration Test FIFO Test Data 0 Register Definitions */ +#define TPI_ITFTTD0_ATB_IF2_ATVALID_Pos 29U /*!< TPI ITFTTD0: ATB Interface 2 ATVALIDPosition */ +#define TPI_ITFTTD0_ATB_IF2_ATVALID_Msk (0x3UL << TPI_ITFTTD0_ATB_IF2_ATVALID_Pos) /*!< TPI ITFTTD0: ATB Interface 2 ATVALID Mask */ + +#define TPI_ITFTTD0_ATB_IF2_bytecount_Pos 27U /*!< TPI ITFTTD0: ATB Interface 2 byte count Position */ +#define TPI_ITFTTD0_ATB_IF2_bytecount_Msk (0x3UL << TPI_ITFTTD0_ATB_IF2_bytecount_Pos) /*!< TPI ITFTTD0: ATB Interface 2 byte count Mask */ + +#define TPI_ITFTTD0_ATB_IF1_ATVALID_Pos 26U /*!< TPI ITFTTD0: ATB Interface 1 ATVALID Position */ +#define TPI_ITFTTD0_ATB_IF1_ATVALID_Msk (0x3UL << TPI_ITFTTD0_ATB_IF1_ATVALID_Pos) /*!< TPI ITFTTD0: ATB Interface 1 ATVALID Mask */ + +#define TPI_ITFTTD0_ATB_IF1_bytecount_Pos 24U /*!< TPI ITFTTD0: ATB Interface 1 byte count Position */ +#define TPI_ITFTTD0_ATB_IF1_bytecount_Msk (0x3UL << TPI_ITFTTD0_ATB_IF1_bytecount_Pos) /*!< TPI ITFTTD0: ATB Interface 1 byte countt Mask */ + +#define TPI_ITFTTD0_ATB_IF1_data2_Pos 16U /*!< TPI ITFTTD0: ATB Interface 1 data2 Position */ +#define TPI_ITFTTD0_ATB_IF1_data2_Msk (0xFFUL << TPI_ITFTTD0_ATB_IF1_data1_Pos) /*!< TPI ITFTTD0: ATB Interface 1 data2 Mask */ + +#define TPI_ITFTTD0_ATB_IF1_data1_Pos 8U /*!< TPI ITFTTD0: ATB Interface 1 data1 Position */ +#define TPI_ITFTTD0_ATB_IF1_data1_Msk (0xFFUL << TPI_ITFTTD0_ATB_IF1_data1_Pos) /*!< TPI ITFTTD0: ATB Interface 1 data1 Mask */ + +#define TPI_ITFTTD0_ATB_IF1_data0_Pos 0U /*!< TPI ITFTTD0: ATB Interface 1 data0 Position */ +#define TPI_ITFTTD0_ATB_IF1_data0_Msk (0xFFUL /*<< TPI_ITFTTD0_ATB_IF1_data0_Pos*/) /*!< TPI ITFTTD0: ATB Interface 1 data0 Mask */ + +/* TPI Integration Test ATB Control Register 2 Register Definitions */ +#define TPI_ITATBCTR2_AFVALID2S_Pos 1U /*!< TPI ITATBCTR2: AFVALID2S Position */ +#define TPI_ITATBCTR2_AFVALID2S_Msk (0x1UL << TPI_ITATBCTR2_AFVALID2S_Pos) /*!< TPI ITATBCTR2: AFVALID2SS Mask */ + +#define TPI_ITATBCTR2_AFVALID1S_Pos 1U /*!< TPI ITATBCTR2: AFVALID1S Position */ +#define TPI_ITATBCTR2_AFVALID1S_Msk (0x1UL << TPI_ITATBCTR2_AFVALID1S_Pos) /*!< TPI ITATBCTR2: AFVALID1SS Mask */ + +#define TPI_ITATBCTR2_ATREADY2S_Pos 0U /*!< TPI ITATBCTR2: ATREADY2S Position */ +#define TPI_ITATBCTR2_ATREADY2S_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY2S_Pos*/) /*!< TPI ITATBCTR2: ATREADY2S Mask */ + +#define TPI_ITATBCTR2_ATREADY1S_Pos 0U /*!< TPI ITATBCTR2: ATREADY1S Position */ +#define TPI_ITATBCTR2_ATREADY1S_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY1S_Pos*/) /*!< TPI ITATBCTR2: ATREADY1S Mask */ + +/* TPI Integration Test FIFO Test Data 1 Register Definitions */ +#define TPI_ITFTTD1_ATB_IF2_ATVALID_Pos 29U /*!< TPI ITFTTD1: ATB Interface 2 ATVALID Position */ +#define TPI_ITFTTD1_ATB_IF2_ATVALID_Msk (0x3UL << TPI_ITFTTD1_ATB_IF2_ATVALID_Pos) /*!< TPI ITFTTD1: ATB Interface 2 ATVALID Mask */ + +#define TPI_ITFTTD1_ATB_IF2_bytecount_Pos 27U /*!< TPI ITFTTD1: ATB Interface 2 byte count Position */ +#define TPI_ITFTTD1_ATB_IF2_bytecount_Msk (0x3UL << TPI_ITFTTD1_ATB_IF2_bytecount_Pos) /*!< TPI ITFTTD1: ATB Interface 2 byte count Mask */ + +#define TPI_ITFTTD1_ATB_IF1_ATVALID_Pos 26U /*!< TPI ITFTTD1: ATB Interface 1 ATVALID Position */ +#define TPI_ITFTTD1_ATB_IF1_ATVALID_Msk (0x3UL << TPI_ITFTTD1_ATB_IF1_ATVALID_Pos) /*!< TPI ITFTTD1: ATB Interface 1 ATVALID Mask */ + +#define TPI_ITFTTD1_ATB_IF1_bytecount_Pos 24U /*!< TPI ITFTTD1: ATB Interface 1 byte count Position */ +#define TPI_ITFTTD1_ATB_IF1_bytecount_Msk (0x3UL << TPI_ITFTTD1_ATB_IF1_bytecount_Pos) /*!< TPI ITFTTD1: ATB Interface 1 byte countt Mask */ + +#define TPI_ITFTTD1_ATB_IF2_data2_Pos 16U /*!< TPI ITFTTD1: ATB Interface 2 data2 Position */ +#define TPI_ITFTTD1_ATB_IF2_data2_Msk (0xFFUL << TPI_ITFTTD1_ATB_IF2_data1_Pos) /*!< TPI ITFTTD1: ATB Interface 2 data2 Mask */ + +#define TPI_ITFTTD1_ATB_IF2_data1_Pos 8U /*!< TPI ITFTTD1: ATB Interface 2 data1 Position */ +#define TPI_ITFTTD1_ATB_IF2_data1_Msk (0xFFUL << TPI_ITFTTD1_ATB_IF2_data1_Pos) /*!< TPI ITFTTD1: ATB Interface 2 data1 Mask */ + +#define TPI_ITFTTD1_ATB_IF2_data0_Pos 0U /*!< TPI ITFTTD1: ATB Interface 2 data0 Position */ +#define TPI_ITFTTD1_ATB_IF2_data0_Msk (0xFFUL /*<< TPI_ITFTTD1_ATB_IF2_data0_Pos*/) /*!< TPI ITFTTD1: ATB Interface 2 data0 Mask */ + +/* TPI Integration Test ATB Control Register 0 Definitions */ +#define TPI_ITATBCTR0_AFVALID2S_Pos 1U /*!< TPI ITATBCTR0: AFVALID2S Position */ +#define TPI_ITATBCTR0_AFVALID2S_Msk (0x1UL << TPI_ITATBCTR0_AFVALID2S_Pos) /*!< TPI ITATBCTR0: AFVALID2SS Mask */ + +#define TPI_ITATBCTR0_AFVALID1S_Pos 1U /*!< TPI ITATBCTR0: AFVALID1S Position */ +#define TPI_ITATBCTR0_AFVALID1S_Msk (0x1UL << TPI_ITATBCTR0_AFVALID1S_Pos) /*!< TPI ITATBCTR0: AFVALID1SS Mask */ + +#define TPI_ITATBCTR0_ATREADY2S_Pos 0U /*!< TPI ITATBCTR0: ATREADY2S Position */ +#define TPI_ITATBCTR0_ATREADY2S_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY2S_Pos*/) /*!< TPI ITATBCTR0: ATREADY2S Mask */ + +#define TPI_ITATBCTR0_ATREADY1S_Pos 0U /*!< TPI ITATBCTR0: ATREADY1S Position */ +#define TPI_ITATBCTR0_ATREADY1S_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY1S_Pos*/) /*!< TPI ITATBCTR0: ATREADY1S Mask */ + +/* TPI Integration Mode Control Register Definitions */ +#define TPI_ITCTRL_Mode_Pos 0U /*!< TPI ITCTRL: Mode Position */ +#define TPI_ITCTRL_Mode_Msk (0x3UL /*<< TPI_ITCTRL_Mode_Pos*/) /*!< TPI ITCTRL: Mode Mask */ + +/* TPI DEVID Register Definitions */ +#define TPI_DEVID_NRZVALID_Pos 11U /*!< TPI DEVID: NRZVALID Position */ +#define TPI_DEVID_NRZVALID_Msk (0x1UL << TPI_DEVID_NRZVALID_Pos) /*!< TPI DEVID: NRZVALID Mask */ + +#define TPI_DEVID_MANCVALID_Pos 10U /*!< TPI DEVID: MANCVALID Position */ +#define TPI_DEVID_MANCVALID_Msk (0x1UL << TPI_DEVID_MANCVALID_Pos) /*!< TPI DEVID: MANCVALID Mask */ + +#define TPI_DEVID_PTINVALID_Pos 9U /*!< TPI DEVID: PTINVALID Position */ +#define TPI_DEVID_PTINVALID_Msk (0x1UL << TPI_DEVID_PTINVALID_Pos) /*!< TPI DEVID: PTINVALID Mask */ + +#define TPI_DEVID_FIFOSZ_Pos 6U /*!< TPI DEVID: FIFOSZ Position */ +#define TPI_DEVID_FIFOSZ_Msk (0x7UL << TPI_DEVID_FIFOSZ_Pos) /*!< TPI DEVID: FIFOSZ Mask */ + +#define TPI_DEVID_NrTraceInput_Pos 0U /*!< TPI DEVID: NrTraceInput Position */ +#define TPI_DEVID_NrTraceInput_Msk (0x3FUL /*<< TPI_DEVID_NrTraceInput_Pos*/) /*!< TPI DEVID: NrTraceInput Mask */ + +/* TPI DEVTYPE Register Definitions */ +#define TPI_DEVTYPE_SubType_Pos 4U /*!< TPI DEVTYPE: SubType Position */ +#define TPI_DEVTYPE_SubType_Msk (0xFUL /*<< TPI_DEVTYPE_SubType_Pos*/) /*!< TPI DEVTYPE: SubType Mask */ + +#define TPI_DEVTYPE_MajorType_Pos 0U /*!< TPI DEVTYPE: MajorType Position */ +#define TPI_DEVTYPE_MajorType_Msk (0xFUL << TPI_DEVTYPE_MajorType_Pos) /*!< TPI DEVTYPE: MajorType Mask */ + +/*@}*/ /* end of group CMSIS_TPI */ + + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_MPU Memory Protection Unit (MPU) + \brief Type definitions for the Memory Protection Unit (MPU) + @{ + */ + +/** + \brief Structure type to access the Memory Protection Unit (MPU). + */ +typedef struct +{ + __IM uint32_t TYPE; /*!< Offset: 0x000 (R/ ) MPU Type Register */ + __IOM uint32_t CTRL; /*!< Offset: 0x004 (R/W) MPU Control Register */ + __IOM uint32_t RNR; /*!< Offset: 0x008 (R/W) MPU Region Number Register */ + __IOM uint32_t RBAR; /*!< Offset: 0x00C (R/W) MPU Region Base Address Register */ + __IOM uint32_t RLAR; /*!< Offset: 0x010 (R/W) MPU Region Limit Address Register */ + __IOM uint32_t RBAR_A1; /*!< Offset: 0x014 (R/W) MPU Region Base Address Register Alias 1 */ + __IOM uint32_t RLAR_A1; /*!< Offset: 0x018 (R/W) MPU Region Limit Address Register Alias 1 */ + __IOM uint32_t RBAR_A2; /*!< Offset: 0x01C (R/W) MPU Region Base Address Register Alias 2 */ + __IOM uint32_t RLAR_A2; /*!< Offset: 0x020 (R/W) MPU Region Limit Address Register Alias 2 */ + __IOM uint32_t RBAR_A3; /*!< Offset: 0x024 (R/W) MPU Region Base Address Register Alias 3 */ + __IOM uint32_t RLAR_A3; /*!< Offset: 0x028 (R/W) MPU Region Limit Address Register Alias 3 */ + uint32_t RESERVED0[1]; + union + { + __IOM uint32_t MAIR[2]; + struct + { + __IOM uint32_t MAIR0; /*!< Offset: 0x030 (R/W) MPU Memory Attribute Indirection Register 0 */ + __IOM uint32_t MAIR1; /*!< Offset: 0x034 (R/W) MPU Memory Attribute Indirection Register 1 */ + }; + }; +} MPU_Type; + +#define MPU_TYPE_RALIASES 4U + +/* MPU Type Register Definitions */ +#define MPU_TYPE_IREGION_Pos 16U /*!< MPU TYPE: IREGION Position */ +#define MPU_TYPE_IREGION_Msk (0xFFUL << MPU_TYPE_IREGION_Pos) /*!< MPU TYPE: IREGION Mask */ + +#define MPU_TYPE_DREGION_Pos 8U /*!< MPU TYPE: DREGION Position */ +#define MPU_TYPE_DREGION_Msk (0xFFUL << MPU_TYPE_DREGION_Pos) /*!< MPU TYPE: DREGION Mask */ + +#define MPU_TYPE_SEPARATE_Pos 0U /*!< MPU TYPE: SEPARATE Position */ +#define MPU_TYPE_SEPARATE_Msk (1UL /*<< MPU_TYPE_SEPARATE_Pos*/) /*!< MPU TYPE: SEPARATE Mask */ + +/* MPU Control Register Definitions */ +#define MPU_CTRL_PRIVDEFENA_Pos 2U /*!< MPU CTRL: PRIVDEFENA Position */ +#define MPU_CTRL_PRIVDEFENA_Msk (1UL << MPU_CTRL_PRIVDEFENA_Pos) /*!< MPU CTRL: PRIVDEFENA Mask */ + +#define MPU_CTRL_HFNMIENA_Pos 1U /*!< MPU CTRL: HFNMIENA Position */ +#define MPU_CTRL_HFNMIENA_Msk (1UL << MPU_CTRL_HFNMIENA_Pos) /*!< MPU CTRL: HFNMIENA Mask */ + +#define MPU_CTRL_ENABLE_Pos 0U /*!< MPU CTRL: ENABLE Position */ +#define MPU_CTRL_ENABLE_Msk (1UL /*<< MPU_CTRL_ENABLE_Pos*/) /*!< MPU CTRL: ENABLE Mask */ + +/* MPU Region Number Register Definitions */ +#define MPU_RNR_REGION_Pos 0U /*!< MPU RNR: REGION Position */ +#define MPU_RNR_REGION_Msk (0xFFUL /*<< MPU_RNR_REGION_Pos*/) /*!< MPU RNR: REGION Mask */ + +/* MPU Region Base Address Register Definitions */ +#define MPU_RBAR_BASE_Pos 5U /*!< MPU RBAR: BASE Position */ +#define MPU_RBAR_BASE_Msk (0x7FFFFFFUL << MPU_RBAR_BASE_Pos) /*!< MPU RBAR: BASE Mask */ + +#define MPU_RBAR_SH_Pos 3U /*!< MPU RBAR: SH Position */ +#define MPU_RBAR_SH_Msk (0x3UL << MPU_RBAR_SH_Pos) /*!< MPU RBAR: SH Mask */ + +#define MPU_RBAR_AP_Pos 1U /*!< MPU RBAR: AP Position */ +#define MPU_RBAR_AP_Msk (0x3UL << MPU_RBAR_AP_Pos) /*!< MPU RBAR: AP Mask */ + +#define MPU_RBAR_XN_Pos 0U /*!< MPU RBAR: XN Position */ +#define MPU_RBAR_XN_Msk (01UL /*<< MPU_RBAR_XN_Pos*/) /*!< MPU RBAR: XN Mask */ + +/* MPU Region Limit Address Register Definitions */ +#define MPU_RLAR_LIMIT_Pos 5U /*!< MPU RLAR: LIMIT Position */ +#define MPU_RLAR_LIMIT_Msk (0x7FFFFFFUL << MPU_RLAR_LIMIT_Pos) /*!< MPU RLAR: LIMIT Mask */ + +#define MPU_RLAR_AttrIndx_Pos 1U /*!< MPU RLAR: AttrIndx Position */ +#define MPU_RLAR_AttrIndx_Msk (0x7UL << MPU_RLAR_AttrIndx_Pos) /*!< MPU RLAR: AttrIndx Mask */ + +#define MPU_RLAR_EN_Pos 0U /*!< MPU RLAR: Region enable bit Position */ +#define MPU_RLAR_EN_Msk (1UL /*<< MPU_RLAR_EN_Pos*/) /*!< MPU RLAR: Region enable bit Disable Mask */ + +/* MPU Memory Attribute Indirection Register 0 Definitions */ +#define MPU_MAIR0_Attr3_Pos 24U /*!< MPU MAIR0: Attr3 Position */ +#define MPU_MAIR0_Attr3_Msk (0xFFUL << MPU_MAIR0_Attr3_Pos) /*!< MPU MAIR0: Attr3 Mask */ + +#define MPU_MAIR0_Attr2_Pos 16U /*!< MPU MAIR0: Attr2 Position */ +#define MPU_MAIR0_Attr2_Msk (0xFFUL << MPU_MAIR0_Attr2_Pos) /*!< MPU MAIR0: Attr2 Mask */ + +#define MPU_MAIR0_Attr1_Pos 8U /*!< MPU MAIR0: Attr1 Position */ +#define MPU_MAIR0_Attr1_Msk (0xFFUL << MPU_MAIR0_Attr1_Pos) /*!< MPU MAIR0: Attr1 Mask */ + +#define MPU_MAIR0_Attr0_Pos 0U /*!< MPU MAIR0: Attr0 Position */ +#define MPU_MAIR0_Attr0_Msk (0xFFUL /*<< MPU_MAIR0_Attr0_Pos*/) /*!< MPU MAIR0: Attr0 Mask */ + +/* MPU Memory Attribute Indirection Register 1 Definitions */ +#define MPU_MAIR1_Attr7_Pos 24U /*!< MPU MAIR1: Attr7 Position */ +#define MPU_MAIR1_Attr7_Msk (0xFFUL << MPU_MAIR1_Attr7_Pos) /*!< MPU MAIR1: Attr7 Mask */ + +#define MPU_MAIR1_Attr6_Pos 16U /*!< MPU MAIR1: Attr6 Position */ +#define MPU_MAIR1_Attr6_Msk (0xFFUL << MPU_MAIR1_Attr6_Pos) /*!< MPU MAIR1: Attr6 Mask */ + +#define MPU_MAIR1_Attr5_Pos 8U /*!< MPU MAIR1: Attr5 Position */ +#define MPU_MAIR1_Attr5_Msk (0xFFUL << MPU_MAIR1_Attr5_Pos) /*!< MPU MAIR1: Attr5 Mask */ + +#define MPU_MAIR1_Attr4_Pos 0U /*!< MPU MAIR1: Attr4 Position */ +#define MPU_MAIR1_Attr4_Msk (0xFFUL /*<< MPU_MAIR1_Attr4_Pos*/) /*!< MPU MAIR1: Attr4 Mask */ + +/*@} end of group CMSIS_MPU */ +#endif + + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_SAU Security Attribution Unit (SAU) + \brief Type definitions for the Security Attribution Unit (SAU) + @{ + */ + +/** + \brief Structure type to access the Security Attribution Unit (SAU). + */ +typedef struct +{ + __IOM uint32_t CTRL; /*!< Offset: 0x000 (R/W) SAU Control Register */ + __IM uint32_t TYPE; /*!< Offset: 0x004 (R/ ) SAU Type Register */ +#if defined (__SAUREGION_PRESENT) && (__SAUREGION_PRESENT == 1U) + __IOM uint32_t RNR; /*!< Offset: 0x008 (R/W) SAU Region Number Register */ + __IOM uint32_t RBAR; /*!< Offset: 0x00C (R/W) SAU Region Base Address Register */ + __IOM uint32_t RLAR; /*!< Offset: 0x010 (R/W) SAU Region Limit Address Register */ +#else + uint32_t RESERVED0[3]; +#endif + __IOM uint32_t SFSR; /*!< Offset: 0x014 (R/W) Secure Fault Status Register */ + __IOM uint32_t SFAR; /*!< Offset: 0x018 (R/W) Secure Fault Address Register */ +} SAU_Type; + +/* SAU Control Register Definitions */ +#define SAU_CTRL_ALLNS_Pos 1U /*!< SAU CTRL: ALLNS Position */ +#define SAU_CTRL_ALLNS_Msk (1UL << SAU_CTRL_ALLNS_Pos) /*!< SAU CTRL: ALLNS Mask */ + +#define SAU_CTRL_ENABLE_Pos 0U /*!< SAU CTRL: ENABLE Position */ +#define SAU_CTRL_ENABLE_Msk (1UL /*<< SAU_CTRL_ENABLE_Pos*/) /*!< SAU CTRL: ENABLE Mask */ + +/* SAU Type Register Definitions */ +#define SAU_TYPE_SREGION_Pos 0U /*!< SAU TYPE: SREGION Position */ +#define SAU_TYPE_SREGION_Msk (0xFFUL /*<< SAU_TYPE_SREGION_Pos*/) /*!< SAU TYPE: SREGION Mask */ + +#if defined (__SAUREGION_PRESENT) && (__SAUREGION_PRESENT == 1U) +/* SAU Region Number Register Definitions */ +#define SAU_RNR_REGION_Pos 0U /*!< SAU RNR: REGION Position */ +#define SAU_RNR_REGION_Msk (0xFFUL /*<< SAU_RNR_REGION_Pos*/) /*!< SAU RNR: REGION Mask */ + +/* SAU Region Base Address Register Definitions */ +#define SAU_RBAR_BADDR_Pos 5U /*!< SAU RBAR: BADDR Position */ +#define SAU_RBAR_BADDR_Msk (0x7FFFFFFUL << SAU_RBAR_BADDR_Pos) /*!< SAU RBAR: BADDR Mask */ + +/* SAU Region Limit Address Register Definitions */ +#define SAU_RLAR_LADDR_Pos 5U /*!< SAU RLAR: LADDR Position */ +#define SAU_RLAR_LADDR_Msk (0x7FFFFFFUL << SAU_RLAR_LADDR_Pos) /*!< SAU RLAR: LADDR Mask */ + +#define SAU_RLAR_NSC_Pos 1U /*!< SAU RLAR: NSC Position */ +#define SAU_RLAR_NSC_Msk (1UL << SAU_RLAR_NSC_Pos) /*!< SAU RLAR: NSC Mask */ + +#define SAU_RLAR_ENABLE_Pos 0U /*!< SAU RLAR: ENABLE Position */ +#define SAU_RLAR_ENABLE_Msk (1UL /*<< SAU_RLAR_ENABLE_Pos*/) /*!< SAU RLAR: ENABLE Mask */ + +#endif /* defined (__SAUREGION_PRESENT) && (__SAUREGION_PRESENT == 1U) */ + +/* Secure Fault Status Register Definitions */ +#define SAU_SFSR_LSERR_Pos 7U /*!< SAU SFSR: LSERR Position */ +#define SAU_SFSR_LSERR_Msk (1UL << SAU_SFSR_LSERR_Pos) /*!< SAU SFSR: LSERR Mask */ + +#define SAU_SFSR_SFARVALID_Pos 6U /*!< SAU SFSR: SFARVALID Position */ +#define SAU_SFSR_SFARVALID_Msk (1UL << SAU_SFSR_SFARVALID_Pos) /*!< SAU SFSR: SFARVALID Mask */ + +#define SAU_SFSR_LSPERR_Pos 5U /*!< SAU SFSR: LSPERR Position */ +#define SAU_SFSR_LSPERR_Msk (1UL << SAU_SFSR_LSPERR_Pos) /*!< SAU SFSR: LSPERR Mask */ + +#define SAU_SFSR_INVTRAN_Pos 4U /*!< SAU SFSR: INVTRAN Position */ +#define SAU_SFSR_INVTRAN_Msk (1UL << SAU_SFSR_INVTRAN_Pos) /*!< SAU SFSR: INVTRAN Mask */ + +#define SAU_SFSR_AUVIOL_Pos 3U /*!< SAU SFSR: AUVIOL Position */ +#define SAU_SFSR_AUVIOL_Msk (1UL << SAU_SFSR_AUVIOL_Pos) /*!< SAU SFSR: AUVIOL Mask */ + +#define SAU_SFSR_INVER_Pos 2U /*!< SAU SFSR: INVER Position */ +#define SAU_SFSR_INVER_Msk (1UL << SAU_SFSR_INVER_Pos) /*!< SAU SFSR: INVER Mask */ + +#define SAU_SFSR_INVIS_Pos 1U /*!< SAU SFSR: INVIS Position */ +#define SAU_SFSR_INVIS_Msk (1UL << SAU_SFSR_INVIS_Pos) /*!< SAU SFSR: INVIS Mask */ + +#define SAU_SFSR_INVEP_Pos 0U /*!< SAU SFSR: INVEP Position */ +#define SAU_SFSR_INVEP_Msk (1UL /*<< SAU_SFSR_INVEP_Pos*/) /*!< SAU SFSR: INVEP Mask */ + +/*@} end of group CMSIS_SAU */ +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_FPU Floating Point Unit (FPU) + \brief Type definitions for the Floating Point Unit (FPU) + @{ + */ + +/** + \brief Structure type to access the Floating Point Unit (FPU). + */ +typedef struct +{ + uint32_t RESERVED0[1U]; + __IOM uint32_t FPCCR; /*!< Offset: 0x004 (R/W) Floating-Point Context Control Register */ + __IOM uint32_t FPCAR; /*!< Offset: 0x008 (R/W) Floating-Point Context Address Register */ + __IOM uint32_t FPDSCR; /*!< Offset: 0x00C (R/W) Floating-Point Default Status Control Register */ + __IM uint32_t MVFR0; /*!< Offset: 0x010 (R/ ) Media and FP Feature Register 0 */ + __IM uint32_t MVFR1; /*!< Offset: 0x014 (R/ ) Media and FP Feature Register 1 */ +} FPU_Type; + +/* Floating-Point Context Control Register Definitions */ +#define FPU_FPCCR_ASPEN_Pos 31U /*!< FPCCR: ASPEN bit Position */ +#define FPU_FPCCR_ASPEN_Msk (1UL << FPU_FPCCR_ASPEN_Pos) /*!< FPCCR: ASPEN bit Mask */ + +#define FPU_FPCCR_LSPEN_Pos 30U /*!< FPCCR: LSPEN Position */ +#define FPU_FPCCR_LSPEN_Msk (1UL << FPU_FPCCR_LSPEN_Pos) /*!< FPCCR: LSPEN bit Mask */ + +#define FPU_FPCCR_LSPENS_Pos 29U /*!< FPCCR: LSPENS Position */ +#define FPU_FPCCR_LSPENS_Msk (1UL << FPU_FPCCR_LSPENS_Pos) /*!< FPCCR: LSPENS bit Mask */ + +#define FPU_FPCCR_CLRONRET_Pos 28U /*!< FPCCR: CLRONRET Position */ +#define FPU_FPCCR_CLRONRET_Msk (1UL << FPU_FPCCR_CLRONRET_Pos) /*!< FPCCR: CLRONRET bit Mask */ + +#define FPU_FPCCR_CLRONRETS_Pos 27U /*!< FPCCR: CLRONRETS Position */ +#define FPU_FPCCR_CLRONRETS_Msk (1UL << FPU_FPCCR_CLRONRETS_Pos) /*!< FPCCR: CLRONRETS bit Mask */ + +#define FPU_FPCCR_TS_Pos 26U /*!< FPCCR: TS Position */ +#define FPU_FPCCR_TS_Msk (1UL << FPU_FPCCR_TS_Pos) /*!< FPCCR: TS bit Mask */ + +#define FPU_FPCCR_UFRDY_Pos 10U /*!< FPCCR: UFRDY Position */ +#define FPU_FPCCR_UFRDY_Msk (1UL << FPU_FPCCR_UFRDY_Pos) /*!< FPCCR: UFRDY bit Mask */ + +#define FPU_FPCCR_SPLIMVIOL_Pos 9U /*!< FPCCR: SPLIMVIOL Position */ +#define FPU_FPCCR_SPLIMVIOL_Msk (1UL << FPU_FPCCR_SPLIMVIOL_Pos) /*!< FPCCR: SPLIMVIOL bit Mask */ + +#define FPU_FPCCR_MONRDY_Pos 8U /*!< FPCCR: MONRDY Position */ +#define FPU_FPCCR_MONRDY_Msk (1UL << FPU_FPCCR_MONRDY_Pos) /*!< FPCCR: MONRDY bit Mask */ + +#define FPU_FPCCR_SFRDY_Pos 7U /*!< FPCCR: SFRDY Position */ +#define FPU_FPCCR_SFRDY_Msk (1UL << FPU_FPCCR_SFRDY_Pos) /*!< FPCCR: SFRDY bit Mask */ + +#define FPU_FPCCR_BFRDY_Pos 6U /*!< FPCCR: BFRDY Position */ +#define FPU_FPCCR_BFRDY_Msk (1UL << FPU_FPCCR_BFRDY_Pos) /*!< FPCCR: BFRDY bit Mask */ + +#define FPU_FPCCR_MMRDY_Pos 5U /*!< FPCCR: MMRDY Position */ +#define FPU_FPCCR_MMRDY_Msk (1UL << FPU_FPCCR_MMRDY_Pos) /*!< FPCCR: MMRDY bit Mask */ + +#define FPU_FPCCR_HFRDY_Pos 4U /*!< FPCCR: HFRDY Position */ +#define FPU_FPCCR_HFRDY_Msk (1UL << FPU_FPCCR_HFRDY_Pos) /*!< FPCCR: HFRDY bit Mask */ + +#define FPU_FPCCR_THREAD_Pos 3U /*!< FPCCR: processor mode bit Position */ +#define FPU_FPCCR_THREAD_Msk (1UL << FPU_FPCCR_THREAD_Pos) /*!< FPCCR: processor mode active bit Mask */ + +#define FPU_FPCCR_S_Pos 2U /*!< FPCCR: Security status of the FP context bit Position */ +#define FPU_FPCCR_S_Msk (1UL << FPU_FPCCR_S_Pos) /*!< FPCCR: Security status of the FP context bit Mask */ + +#define FPU_FPCCR_USER_Pos 1U /*!< FPCCR: privilege level bit Position */ +#define FPU_FPCCR_USER_Msk (1UL << FPU_FPCCR_USER_Pos) /*!< FPCCR: privilege level bit Mask */ + +#define FPU_FPCCR_LSPACT_Pos 0U /*!< FPCCR: Lazy state preservation active bit Position */ +#define FPU_FPCCR_LSPACT_Msk (1UL /*<< FPU_FPCCR_LSPACT_Pos*/) /*!< FPCCR: Lazy state preservation active bit Mask */ + +/* Floating-Point Context Address Register Definitions */ +#define FPU_FPCAR_ADDRESS_Pos 3U /*!< FPCAR: ADDRESS bit Position */ +#define FPU_FPCAR_ADDRESS_Msk (0x1FFFFFFFUL << FPU_FPCAR_ADDRESS_Pos) /*!< FPCAR: ADDRESS bit Mask */ + +/* Floating-Point Default Status Control Register Definitions */ +#define FPU_FPDSCR_AHP_Pos 26U /*!< FPDSCR: AHP bit Position */ +#define FPU_FPDSCR_AHP_Msk (1UL << FPU_FPDSCR_AHP_Pos) /*!< FPDSCR: AHP bit Mask */ + +#define FPU_FPDSCR_DN_Pos 25U /*!< FPDSCR: DN bit Position */ +#define FPU_FPDSCR_DN_Msk (1UL << FPU_FPDSCR_DN_Pos) /*!< FPDSCR: DN bit Mask */ + +#define FPU_FPDSCR_FZ_Pos 24U /*!< FPDSCR: FZ bit Position */ +#define FPU_FPDSCR_FZ_Msk (1UL << FPU_FPDSCR_FZ_Pos) /*!< FPDSCR: FZ bit Mask */ + +#define FPU_FPDSCR_RMode_Pos 22U /*!< FPDSCR: RMode bit Position */ +#define FPU_FPDSCR_RMode_Msk (3UL << FPU_FPDSCR_RMode_Pos) /*!< FPDSCR: RMode bit Mask */ + +/* Media and FP Feature Register 0 Definitions */ +#define FPU_MVFR0_FP_rounding_modes_Pos 28U /*!< MVFR0: FP rounding modes bits Position */ +#define FPU_MVFR0_FP_rounding_modes_Msk (0xFUL << FPU_MVFR0_FP_rounding_modes_Pos) /*!< MVFR0: FP rounding modes bits Mask */ + +#define FPU_MVFR0_Short_vectors_Pos 24U /*!< MVFR0: Short vectors bits Position */ +#define FPU_MVFR0_Short_vectors_Msk (0xFUL << FPU_MVFR0_Short_vectors_Pos) /*!< MVFR0: Short vectors bits Mask */ + +#define FPU_MVFR0_Square_root_Pos 20U /*!< MVFR0: Square root bits Position */ +#define FPU_MVFR0_Square_root_Msk (0xFUL << FPU_MVFR0_Square_root_Pos) /*!< MVFR0: Square root bits Mask */ + +#define FPU_MVFR0_Divide_Pos 16U /*!< MVFR0: Divide bits Position */ +#define FPU_MVFR0_Divide_Msk (0xFUL << FPU_MVFR0_Divide_Pos) /*!< MVFR0: Divide bits Mask */ + +#define FPU_MVFR0_FP_excep_trapping_Pos 12U /*!< MVFR0: FP exception trapping bits Position */ +#define FPU_MVFR0_FP_excep_trapping_Msk (0xFUL << FPU_MVFR0_FP_excep_trapping_Pos) /*!< MVFR0: FP exception trapping bits Mask */ + +#define FPU_MVFR0_Double_precision_Pos 8U /*!< MVFR0: Double-precision bits Position */ +#define FPU_MVFR0_Double_precision_Msk (0xFUL << FPU_MVFR0_Double_precision_Pos) /*!< MVFR0: Double-precision bits Mask */ + +#define FPU_MVFR0_Single_precision_Pos 4U /*!< MVFR0: Single-precision bits Position */ +#define FPU_MVFR0_Single_precision_Msk (0xFUL << FPU_MVFR0_Single_precision_Pos) /*!< MVFR0: Single-precision bits Mask */ + +#define FPU_MVFR0_A_SIMD_registers_Pos 0U /*!< MVFR0: A_SIMD registers bits Position */ +#define FPU_MVFR0_A_SIMD_registers_Msk (0xFUL /*<< FPU_MVFR0_A_SIMD_registers_Pos*/) /*!< MVFR0: A_SIMD registers bits Mask */ + +/* Media and FP Feature Register 1 Definitions */ +#define FPU_MVFR1_FP_fused_MAC_Pos 28U /*!< MVFR1: FP fused MAC bits Position */ +#define FPU_MVFR1_FP_fused_MAC_Msk (0xFUL << FPU_MVFR1_FP_fused_MAC_Pos) /*!< MVFR1: FP fused MAC bits Mask */ + +#define FPU_MVFR1_FP_HPFP_Pos 24U /*!< MVFR1: FP HPFP bits Position */ +#define FPU_MVFR1_FP_HPFP_Msk (0xFUL << FPU_MVFR1_FP_HPFP_Pos) /*!< MVFR1: FP HPFP bits Mask */ + +#define FPU_MVFR1_D_NaN_mode_Pos 4U /*!< MVFR1: D_NaN mode bits Position */ +#define FPU_MVFR1_D_NaN_mode_Msk (0xFUL << FPU_MVFR1_D_NaN_mode_Pos) /*!< MVFR1: D_NaN mode bits Mask */ + +#define FPU_MVFR1_FtZ_mode_Pos 0U /*!< MVFR1: FtZ mode bits Position */ +#define FPU_MVFR1_FtZ_mode_Msk (0xFUL /*<< FPU_MVFR1_FtZ_mode_Pos*/) /*!< MVFR1: FtZ mode bits Mask */ + +/*@} end of group CMSIS_FPU */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_CoreDebug Core Debug Registers (CoreDebug) + \brief Type definitions for the Core Debug Registers + @{ + */ + +/** + \brief Structure type to access the Core Debug Register (CoreDebug). + */ +typedef struct +{ + __IOM uint32_t DHCSR; /*!< Offset: 0x000 (R/W) Debug Halting Control and Status Register */ + __OM uint32_t DCRSR; /*!< Offset: 0x004 ( /W) Debug Core Register Selector Register */ + __IOM uint32_t DCRDR; /*!< Offset: 0x008 (R/W) Debug Core Register Data Register */ + __IOM uint32_t DEMCR; /*!< Offset: 0x00C (R/W) Debug Exception and Monitor Control Register */ + uint32_t RESERVED4[1U]; + __IOM uint32_t DAUTHCTRL; /*!< Offset: 0x014 (R/W) Debug Authentication Control Register */ + __IOM uint32_t DSCSR; /*!< Offset: 0x018 (R/W) Debug Security Control and Status Register */ +} CoreDebug_Type; + +/* Debug Halting Control and Status Register Definitions */ +#define CoreDebug_DHCSR_DBGKEY_Pos 16U /*!< CoreDebug DHCSR: DBGKEY Position */ +#define CoreDebug_DHCSR_DBGKEY_Msk (0xFFFFUL << CoreDebug_DHCSR_DBGKEY_Pos) /*!< CoreDebug DHCSR: DBGKEY Mask */ + +#define CoreDebug_DHCSR_S_RESTART_ST_Pos 26U /*!< CoreDebug DHCSR: S_RESTART_ST Position */ +#define CoreDebug_DHCSR_S_RESTART_ST_Msk (1UL << CoreDebug_DHCSR_S_RESTART_ST_Pos) /*!< CoreDebug DHCSR: S_RESTART_ST Mask */ + +#define CoreDebug_DHCSR_S_RESET_ST_Pos 25U /*!< CoreDebug DHCSR: S_RESET_ST Position */ +#define CoreDebug_DHCSR_S_RESET_ST_Msk (1UL << CoreDebug_DHCSR_S_RESET_ST_Pos) /*!< CoreDebug DHCSR: S_RESET_ST Mask */ + +#define CoreDebug_DHCSR_S_RETIRE_ST_Pos 24U /*!< CoreDebug DHCSR: S_RETIRE_ST Position */ +#define CoreDebug_DHCSR_S_RETIRE_ST_Msk (1UL << CoreDebug_DHCSR_S_RETIRE_ST_Pos) /*!< CoreDebug DHCSR: S_RETIRE_ST Mask */ + +#define CoreDebug_DHCSR_S_LOCKUP_Pos 19U /*!< CoreDebug DHCSR: S_LOCKUP Position */ +#define CoreDebug_DHCSR_S_LOCKUP_Msk (1UL << CoreDebug_DHCSR_S_LOCKUP_Pos) /*!< CoreDebug DHCSR: S_LOCKUP Mask */ + +#define CoreDebug_DHCSR_S_SLEEP_Pos 18U /*!< CoreDebug DHCSR: S_SLEEP Position */ +#define CoreDebug_DHCSR_S_SLEEP_Msk (1UL << CoreDebug_DHCSR_S_SLEEP_Pos) /*!< CoreDebug DHCSR: S_SLEEP Mask */ + +#define CoreDebug_DHCSR_S_HALT_Pos 17U /*!< CoreDebug DHCSR: S_HALT Position */ +#define CoreDebug_DHCSR_S_HALT_Msk (1UL << CoreDebug_DHCSR_S_HALT_Pos) /*!< CoreDebug DHCSR: S_HALT Mask */ + +#define CoreDebug_DHCSR_S_REGRDY_Pos 16U /*!< CoreDebug DHCSR: S_REGRDY Position */ +#define CoreDebug_DHCSR_S_REGRDY_Msk (1UL << CoreDebug_DHCSR_S_REGRDY_Pos) /*!< CoreDebug DHCSR: S_REGRDY Mask */ + +#define CoreDebug_DHCSR_C_SNAPSTALL_Pos 5U /*!< CoreDebug DHCSR: C_SNAPSTALL Position */ +#define CoreDebug_DHCSR_C_SNAPSTALL_Msk (1UL << CoreDebug_DHCSR_C_SNAPSTALL_Pos) /*!< CoreDebug DHCSR: C_SNAPSTALL Mask */ + +#define CoreDebug_DHCSR_C_MASKINTS_Pos 3U /*!< CoreDebug DHCSR: C_MASKINTS Position */ +#define CoreDebug_DHCSR_C_MASKINTS_Msk (1UL << CoreDebug_DHCSR_C_MASKINTS_Pos) /*!< CoreDebug DHCSR: C_MASKINTS Mask */ + +#define CoreDebug_DHCSR_C_STEP_Pos 2U /*!< CoreDebug DHCSR: C_STEP Position */ +#define CoreDebug_DHCSR_C_STEP_Msk (1UL << CoreDebug_DHCSR_C_STEP_Pos) /*!< CoreDebug DHCSR: C_STEP Mask */ + +#define CoreDebug_DHCSR_C_HALT_Pos 1U /*!< CoreDebug DHCSR: C_HALT Position */ +#define CoreDebug_DHCSR_C_HALT_Msk (1UL << CoreDebug_DHCSR_C_HALT_Pos) /*!< CoreDebug DHCSR: C_HALT Mask */ + +#define CoreDebug_DHCSR_C_DEBUGEN_Pos 0U /*!< CoreDebug DHCSR: C_DEBUGEN Position */ +#define CoreDebug_DHCSR_C_DEBUGEN_Msk (1UL /*<< CoreDebug_DHCSR_C_DEBUGEN_Pos*/) /*!< CoreDebug DHCSR: C_DEBUGEN Mask */ + +/* Debug Core Register Selector Register Definitions */ +#define CoreDebug_DCRSR_REGWnR_Pos 16U /*!< CoreDebug DCRSR: REGWnR Position */ +#define CoreDebug_DCRSR_REGWnR_Msk (1UL << CoreDebug_DCRSR_REGWnR_Pos) /*!< CoreDebug DCRSR: REGWnR Mask */ + +#define CoreDebug_DCRSR_REGSEL_Pos 0U /*!< CoreDebug DCRSR: REGSEL Position */ +#define CoreDebug_DCRSR_REGSEL_Msk (0x1FUL /*<< CoreDebug_DCRSR_REGSEL_Pos*/) /*!< CoreDebug DCRSR: REGSEL Mask */ + +/* Debug Exception and Monitor Control Register Definitions */ +#define CoreDebug_DEMCR_TRCENA_Pos 24U /*!< CoreDebug DEMCR: TRCENA Position */ +#define CoreDebug_DEMCR_TRCENA_Msk (1UL << CoreDebug_DEMCR_TRCENA_Pos) /*!< CoreDebug DEMCR: TRCENA Mask */ + +#define CoreDebug_DEMCR_MON_REQ_Pos 19U /*!< CoreDebug DEMCR: MON_REQ Position */ +#define CoreDebug_DEMCR_MON_REQ_Msk (1UL << CoreDebug_DEMCR_MON_REQ_Pos) /*!< CoreDebug DEMCR: MON_REQ Mask */ + +#define CoreDebug_DEMCR_MON_STEP_Pos 18U /*!< CoreDebug DEMCR: MON_STEP Position */ +#define CoreDebug_DEMCR_MON_STEP_Msk (1UL << CoreDebug_DEMCR_MON_STEP_Pos) /*!< CoreDebug DEMCR: MON_STEP Mask */ + +#define CoreDebug_DEMCR_MON_PEND_Pos 17U /*!< CoreDebug DEMCR: MON_PEND Position */ +#define CoreDebug_DEMCR_MON_PEND_Msk (1UL << CoreDebug_DEMCR_MON_PEND_Pos) /*!< CoreDebug DEMCR: MON_PEND Mask */ + +#define CoreDebug_DEMCR_MON_EN_Pos 16U /*!< CoreDebug DEMCR: MON_EN Position */ +#define CoreDebug_DEMCR_MON_EN_Msk (1UL << CoreDebug_DEMCR_MON_EN_Pos) /*!< CoreDebug DEMCR: MON_EN Mask */ + +#define CoreDebug_DEMCR_VC_HARDERR_Pos 10U /*!< CoreDebug DEMCR: VC_HARDERR Position */ +#define CoreDebug_DEMCR_VC_HARDERR_Msk (1UL << CoreDebug_DEMCR_VC_HARDERR_Pos) /*!< CoreDebug DEMCR: VC_HARDERR Mask */ + +#define CoreDebug_DEMCR_VC_INTERR_Pos 9U /*!< CoreDebug DEMCR: VC_INTERR Position */ +#define CoreDebug_DEMCR_VC_INTERR_Msk (1UL << CoreDebug_DEMCR_VC_INTERR_Pos) /*!< CoreDebug DEMCR: VC_INTERR Mask */ + +#define CoreDebug_DEMCR_VC_BUSERR_Pos 8U /*!< CoreDebug DEMCR: VC_BUSERR Position */ +#define CoreDebug_DEMCR_VC_BUSERR_Msk (1UL << CoreDebug_DEMCR_VC_BUSERR_Pos) /*!< CoreDebug DEMCR: VC_BUSERR Mask */ + +#define CoreDebug_DEMCR_VC_STATERR_Pos 7U /*!< CoreDebug DEMCR: VC_STATERR Position */ +#define CoreDebug_DEMCR_VC_STATERR_Msk (1UL << CoreDebug_DEMCR_VC_STATERR_Pos) /*!< CoreDebug DEMCR: VC_STATERR Mask */ + +#define CoreDebug_DEMCR_VC_CHKERR_Pos 6U /*!< CoreDebug DEMCR: VC_CHKERR Position */ +#define CoreDebug_DEMCR_VC_CHKERR_Msk (1UL << CoreDebug_DEMCR_VC_CHKERR_Pos) /*!< CoreDebug DEMCR: VC_CHKERR Mask */ + +#define CoreDebug_DEMCR_VC_NOCPERR_Pos 5U /*!< CoreDebug DEMCR: VC_NOCPERR Position */ +#define CoreDebug_DEMCR_VC_NOCPERR_Msk (1UL << CoreDebug_DEMCR_VC_NOCPERR_Pos) /*!< CoreDebug DEMCR: VC_NOCPERR Mask */ + +#define CoreDebug_DEMCR_VC_MMERR_Pos 4U /*!< CoreDebug DEMCR: VC_MMERR Position */ +#define CoreDebug_DEMCR_VC_MMERR_Msk (1UL << CoreDebug_DEMCR_VC_MMERR_Pos) /*!< CoreDebug DEMCR: VC_MMERR Mask */ + +#define CoreDebug_DEMCR_VC_CORERESET_Pos 0U /*!< CoreDebug DEMCR: VC_CORERESET Position */ +#define CoreDebug_DEMCR_VC_CORERESET_Msk (1UL /*<< CoreDebug_DEMCR_VC_CORERESET_Pos*/) /*!< CoreDebug DEMCR: VC_CORERESET Mask */ + +/* Debug Authentication Control Register Definitions */ +#define CoreDebug_DAUTHCTRL_INTSPNIDEN_Pos 3U /*!< CoreDebug DAUTHCTRL: INTSPNIDEN, Position */ +#define CoreDebug_DAUTHCTRL_INTSPNIDEN_Msk (1UL << CoreDebug_DAUTHCTRL_INTSPNIDEN_Pos) /*!< CoreDebug DAUTHCTRL: INTSPNIDEN, Mask */ + +#define CoreDebug_DAUTHCTRL_SPNIDENSEL_Pos 2U /*!< CoreDebug DAUTHCTRL: SPNIDENSEL Position */ +#define CoreDebug_DAUTHCTRL_SPNIDENSEL_Msk (1UL << CoreDebug_DAUTHCTRL_SPNIDENSEL_Pos) /*!< CoreDebug DAUTHCTRL: SPNIDENSEL Mask */ + +#define CoreDebug_DAUTHCTRL_INTSPIDEN_Pos 1U /*!< CoreDebug DAUTHCTRL: INTSPIDEN Position */ +#define CoreDebug_DAUTHCTRL_INTSPIDEN_Msk (1UL << CoreDebug_DAUTHCTRL_INTSPIDEN_Pos) /*!< CoreDebug DAUTHCTRL: INTSPIDEN Mask */ + +#define CoreDebug_DAUTHCTRL_SPIDENSEL_Pos 0U /*!< CoreDebug DAUTHCTRL: SPIDENSEL Position */ +#define CoreDebug_DAUTHCTRL_SPIDENSEL_Msk (1UL /*<< CoreDebug_DAUTHCTRL_SPIDENSEL_Pos*/) /*!< CoreDebug DAUTHCTRL: SPIDENSEL Mask */ + +/* Debug Security Control and Status Register Definitions */ +#define CoreDebug_DSCSR_CDS_Pos 16U /*!< CoreDebug DSCSR: CDS Position */ +#define CoreDebug_DSCSR_CDS_Msk (1UL << CoreDebug_DSCSR_CDS_Pos) /*!< CoreDebug DSCSR: CDS Mask */ + +#define CoreDebug_DSCSR_SBRSEL_Pos 1U /*!< CoreDebug DSCSR: SBRSEL Position */ +#define CoreDebug_DSCSR_SBRSEL_Msk (1UL << CoreDebug_DSCSR_SBRSEL_Pos) /*!< CoreDebug DSCSR: SBRSEL Mask */ + +#define CoreDebug_DSCSR_SBRSELEN_Pos 0U /*!< CoreDebug DSCSR: SBRSELEN Position */ +#define CoreDebug_DSCSR_SBRSELEN_Msk (1UL /*<< CoreDebug_DSCSR_SBRSELEN_Pos*/) /*!< CoreDebug DSCSR: SBRSELEN Mask */ + +/*@} end of group CMSIS_CoreDebug */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_core_bitfield Core register bit field macros + \brief Macros for use with bit field definitions (xxx_Pos, xxx_Msk). + @{ + */ + +/** + \brief Mask and shift a bit field value for use in a register bit range. + \param[in] field Name of the register bit field. + \param[in] value Value of the bit field. This parameter is interpreted as an uint32_t type. + \return Masked and shifted value. +*/ +#define _VAL2FLD(field, value) (((uint32_t)(value) << field ## _Pos) & field ## _Msk) + +/** + \brief Mask and shift a register value to extract a bit filed value. + \param[in] field Name of the register bit field. + \param[in] value Value of register. This parameter is interpreted as an uint32_t type. + \return Masked and shifted bit field value. +*/ +#define _FLD2VAL(field, value) (((uint32_t)(value) & field ## _Msk) >> field ## _Pos) + +/*@} end of group CMSIS_core_bitfield */ + + +/** + \ingroup CMSIS_core_register + \defgroup CMSIS_core_base Core Definitions + \brief Definitions for base addresses, unions, and structures. + @{ + */ + +/* Memory mapping of Core Hardware */ +#define SCS_BASE (0xE000E000UL) /*!< System Control Space Base Address */ +#define ITM_BASE (0xE0000000UL) /*!< ITM Base Address */ +#define DWT_BASE (0xE0001000UL) /*!< DWT Base Address */ +#define TPI_BASE (0xE0040000UL) /*!< TPI Base Address */ +#define CoreDebug_BASE (0xE000EDF0UL) /*!< Core Debug Base Address */ +#define SysTick_BASE (SCS_BASE + 0x0010UL) /*!< SysTick Base Address */ +#define NVIC_BASE (SCS_BASE + 0x0100UL) /*!< NVIC Base Address */ +#define SCB_BASE (SCS_BASE + 0x0D00UL) /*!< System Control Block Base Address */ + +#define SCnSCB ((SCnSCB_Type *) SCS_BASE ) /*!< System control Register not in SCB */ +#define SCB ((SCB_Type *) SCB_BASE ) /*!< SCB configuration struct */ +#define SysTick ((SysTick_Type *) SysTick_BASE ) /*!< SysTick configuration struct */ +#define NVIC ((NVIC_Type *) NVIC_BASE ) /*!< NVIC configuration struct */ +#define ITM ((ITM_Type *) ITM_BASE ) /*!< ITM configuration struct */ +#define DWT ((DWT_Type *) DWT_BASE ) /*!< DWT configuration struct */ +#define TPI ((TPI_Type *) TPI_BASE ) /*!< TPI configuration struct */ +#define CoreDebug ((CoreDebug_Type *) CoreDebug_BASE ) /*!< Core Debug configuration struct */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) +#define MPU_BASE (SCS_BASE + 0x0D90UL) /*!< Memory Protection Unit */ +#define MPU ((MPU_Type *) MPU_BASE ) /*!< Memory Protection Unit */ +#endif + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +#define SAU_BASE (SCS_BASE + 0x0DD0UL) /*!< Security Attribution Unit */ +#define SAU ((SAU_Type *) SAU_BASE ) /*!< Security Attribution Unit */ +#endif + +#define FPU_BASE (SCS_BASE + 0x0F30UL) /*!< Floating Point Unit */ +#define FPU ((FPU_Type *) FPU_BASE ) /*!< Floating Point Unit */ + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +#define SCS_BASE_NS (0xE002E000UL) /*!< System Control Space Base Address (non-secure address space) */ +#define CoreDebug_BASE_NS (0xE002EDF0UL) /*!< Core Debug Base Address (non-secure address space) */ +#define SysTick_BASE_NS (SCS_BASE_NS + 0x0010UL) /*!< SysTick Base Address (non-secure address space) */ +#define NVIC_BASE_NS (SCS_BASE_NS + 0x0100UL) /*!< NVIC Base Address (non-secure address space) */ +#define SCB_BASE_NS (SCS_BASE_NS + 0x0D00UL) /*!< System Control Block Base Address (non-secure address space) */ + +#define SCnSCB_NS ((SCnSCB_Type *) SCS_BASE_NS ) /*!< System control Register not in SCB(non-secure address space) */ +#define SCB_NS ((SCB_Type *) SCB_BASE_NS ) /*!< SCB configuration struct (non-secure address space) */ +#define SysTick_NS ((SysTick_Type *) SysTick_BASE_NS ) /*!< SysTick configuration struct (non-secure address space) */ +#define NVIC_NS ((NVIC_Type *) NVIC_BASE_NS ) /*!< NVIC configuration struct (non-secure address space) */ +#define CoreDebug_NS ((CoreDebug_Type *) CoreDebug_BASE_NS) /*!< Core Debug configuration struct (non-secure address space) */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) +#define MPU_BASE_NS (SCS_BASE_NS + 0x0D90UL) /*!< Memory Protection Unit (non-secure address space) */ +#define MPU_NS ((MPU_Type *) MPU_BASE_NS ) /*!< Memory Protection Unit (non-secure address space) */ +#endif + +#define FPU_BASE_NS (SCS_BASE_NS + 0x0F30UL) /*!< Floating Point Unit (non-secure address space) */ +#define FPU_NS ((FPU_Type *) FPU_BASE_NS ) /*!< Floating Point Unit (non-secure address space) */ + +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ +/*@} */ + + + +/******************************************************************************* + * Hardware Abstraction Layer + Core Function Interface contains: + - Core NVIC Functions + - Core SysTick Functions + - Core Debug Functions + - Core Register Access Functions + ******************************************************************************/ +/** + \defgroup CMSIS_Core_FunctionInterface Functions and Instructions Reference +*/ + + + +/* ########################## NVIC functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_NVICFunctions NVIC Functions + \brief Functions that manage interrupts and exceptions via the NVIC. + @{ + */ + +#ifdef CMSIS_NVIC_VIRTUAL +#ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE +#define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h" +#endif +#include CMSIS_NVIC_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetPriorityGrouping __NVIC_SetPriorityGrouping +#define NVIC_GetPriorityGrouping __NVIC_GetPriorityGrouping +#define NVIC_EnableIRQ __NVIC_EnableIRQ +#define NVIC_GetEnableIRQ __NVIC_GetEnableIRQ +#define NVIC_DisableIRQ __NVIC_DisableIRQ +#define NVIC_GetPendingIRQ __NVIC_GetPendingIRQ +#define NVIC_SetPendingIRQ __NVIC_SetPendingIRQ +#define NVIC_ClearPendingIRQ __NVIC_ClearPendingIRQ +#define NVIC_GetActive __NVIC_GetActive +#define NVIC_SetPriority __NVIC_SetPriority +#define NVIC_GetPriority __NVIC_GetPriority +#define NVIC_SystemReset __NVIC_SystemReset +#endif /* CMSIS_NVIC_VIRTUAL */ + +#ifdef CMSIS_VECTAB_VIRTUAL +#ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h" +#endif +#include CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetVector __NVIC_SetVector +#define NVIC_GetVector __NVIC_GetVector +#endif /* (CMSIS_VECTAB_VIRTUAL) */ + +#define NVIC_USER_IRQ_OFFSET 16 + + +/* Special LR values for Secure/Non-Secure call handling and exception handling */ + +/* Function Return Payload (from ARMv8-M Architecture Reference Manual) LR value on entry from Secure BLXNS */ +#define FNC_RETURN (0xFEFFFFFFUL) /* bit [0] ignored when processing a branch */ + +/* The following EXC_RETURN mask values are used to evaluate the LR on exception entry */ +#define EXC_RETURN_PREFIX (0xFF000000UL) /* bits [31:24] set to indicate an EXC_RETURN value */ +#define EXC_RETURN_S (0x00000040UL) /* bit [6] stack used to push registers: 0=Non-secure 1=Secure */ +#define EXC_RETURN_DCRS (0x00000020UL) /* bit [5] stacking rules for called registers: 0=skipped 1=saved */ +#define EXC_RETURN_FTYPE (0x00000010UL) /* bit [4] allocate stack for floating-point context: 0=done 1=skipped */ +#define EXC_RETURN_MODE (0x00000008UL) /* bit [3] processor mode for return: 0=Handler mode 1=Thread mode */ +#define EXC_RETURN_SPSEL (0x00000002UL) /* bit [1] stack pointer used to restore context: 0=MSP 1=PSP */ +#define EXC_RETURN_ES (0x00000001UL) /* bit [0] security state exception was taken to: 0=Non-secure 1=Secure */ + +/* Integrity Signature (from ARMv8-M Architecture Reference Manual) for exception context stacking */ +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) /* Value for processors with floating-point extension: */ +#define EXC_INTEGRITY_SIGNATURE (0xFEFA125AUL) /* bit [0] SFTC must match LR bit[4] EXC_RETURN_FTYPE */ +#else +#define EXC_INTEGRITY_SIGNATURE (0xFEFA125BUL) /* Value for processors without floating-point extension */ +#endif + + +/** + \brief Set Priority Grouping + \details Sets the priority grouping field using the required unlock sequence. + The parameter PriorityGroup is assigned to the field SCB->AIRCR [10:8] PRIGROUP field. + Only values from 0..7 are used. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set. + \param [in] PriorityGroup Priority grouping field. + */ +__STATIC_INLINE void __NVIC_SetPriorityGrouping(uint32_t PriorityGroup) +{ + uint32_t reg_value; + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + + reg_value = SCB->AIRCR; /* read old register configuration */ + reg_value &= ~((uint32_t)(SCB_AIRCR_VECTKEY_Msk | SCB_AIRCR_PRIGROUP_Msk)); /* clear bits to change */ + reg_value = (reg_value | + ((uint32_t)0x5FAUL << SCB_AIRCR_VECTKEY_Pos) | + (PriorityGroupTmp << 8U) ); /* Insert write key and priority group */ + SCB->AIRCR = reg_value; +} + + +/** + \brief Get Priority Grouping + \details Reads the priority grouping field from the NVIC Interrupt Controller. + \return Priority grouping field (SCB->AIRCR [10:8] PRIGROUP field). + */ +__STATIC_INLINE uint32_t __NVIC_GetPriorityGrouping(void) +{ + return ((uint32_t)((SCB->AIRCR & SCB_AIRCR_PRIGROUP_Msk) >> SCB_AIRCR_PRIGROUP_Pos)); +} + + +/** + \brief Enable Interrupt + \details Enables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Interrupt Enable status + \details Returns a device specific interrupt enable status from the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Disable Interrupt + \details Disables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + __DSB(); + __ISB(); + } +} + + +/** + \brief Get Pending Interrupt + \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not pending. + \return 1 Interrupt status is pending. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Pending Interrupt + \details Sets the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Clear Pending Interrupt + \details Clears the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Active Interrupt + \details Reads the active register in the NVIC and returns the active bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not active. + \return 1 Interrupt status is active. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t __NVIC_GetActive(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->IABR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \brief Get Interrupt Target State + \details Reads the interrupt target field in the NVIC and returns the interrupt target bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 if interrupt is assigned to Secure + \return 1 if interrupt is assigned to Non Secure + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t NVIC_GetTargetState(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Interrupt Target State + \details Sets the interrupt target field in the NVIC and returns the interrupt target bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 if interrupt is assigned to Secure + 1 if interrupt is assigned to Non Secure + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t NVIC_SetTargetState(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] |= ((uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL))); + return ((uint32_t)(((NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Clear Interrupt Target State + \details Clears the interrupt target field in the NVIC and returns the interrupt target bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 if interrupt is assigned to Secure + 1 if interrupt is assigned to Non Secure + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t NVIC_ClearTargetState(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] &= ~((uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL))); + return ((uint32_t)(((NVIC->ITNS[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + + +/** + \brief Set Interrupt Priority + \details Sets the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \param [in] priority Priority to set. + \note The priority cannot be set for every processor exception. + */ +__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->IPR[((uint32_t)IRQn)] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + } + else + { + SCB->SHPR[(((uint32_t)IRQn) & 0xFUL) - 4UL] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + } +} + + +/** + \brief Get Interrupt Priority + \details Reads the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Interrupt Priority. + Value is aligned automatically to the implemented priority bits of the microcontroller. + */ +__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn) +{ + + if ((int32_t)(IRQn) >= 0) + { + return (((uint32_t)NVIC->IPR[((uint32_t)IRQn)] >> (8U - __NVIC_PRIO_BITS))); + } + else + { + return (((uint32_t)SCB->SHPR[(((uint32_t)IRQn) & 0xFUL) - 4UL] >> (8U - __NVIC_PRIO_BITS))); + } +} + + +/** + \brief Encode Priority + \details Encodes the priority for an interrupt with the given priority group, + preemptive priority value, and subpriority value. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set. + \param [in] PriorityGroup Used priority group. + \param [in] PreemptPriority Preemptive priority value (starting from 0). + \param [in] SubPriority Subpriority value (starting from 0). + \return Encoded priority. Value can be used in the function \ref NVIC_SetPriority(). + */ +__STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority) +{ + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + uint32_t PreemptPriorityBits; + uint32_t SubPriorityBits; + + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); + SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + + return ( + ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) | + ((SubPriority & (uint32_t)((1UL << (SubPriorityBits )) - 1UL))) + ); +} + + +/** + \brief Decode Priority + \details Decodes an interrupt priority value with a given priority group to + preemptive priority value and subpriority value. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set. + \param [in] Priority Priority value, which can be retrieved with the function \ref NVIC_GetPriority(). + \param [in] PriorityGroup Used priority group. + \param [out] pPreemptPriority Preemptive priority value (starting from 0). + \param [out] pSubPriority Subpriority value (starting from 0). + */ +__STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* const pPreemptPriority, uint32_t* const pSubPriority) +{ + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + uint32_t PreemptPriorityBits; + uint32_t SubPriorityBits; + + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); + SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + + *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL); + *pSubPriority = (Priority ) & (uint32_t)((1UL << (SubPriorityBits )) - 1UL); +} + + +/** + \brief Set Interrupt Vector + \details Sets an interrupt vector in SRAM based interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + VTOR must been relocated to SRAM before. + \param [in] IRQn Interrupt number + \param [in] vector Address of interrupt handler function + */ +__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector) +{ + uint32_t* vectors = (uint32_t*)SCB->VTOR; + vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector; +} + + +/** + \brief Get Interrupt Vector + \details Reads an interrupt vector from interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Address of interrupt handler function + */ +__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn) +{ + uint32_t* vectors = (uint32_t*)SCB->VTOR; + return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET]; +} + + +/** + \brief System Reset + \details Initiates a system reset request to reset the MCU. + */ +__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void) +{ + __DSB(); /* Ensure all outstanding memory accesses included + buffered write are completed before reset */ + SCB->AIRCR = (uint32_t)((0x5FAUL << SCB_AIRCR_VECTKEY_Pos) | + (SCB->AIRCR & SCB_AIRCR_PRIGROUP_Msk) | + SCB_AIRCR_SYSRESETREQ_Msk ); /* Keep priority group unchanged */ + __DSB(); /* Ensure completion of memory access */ + + for (;;) /* wait until reset */ + { + __NOP(); + } +} + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \brief Set Priority Grouping (non-secure) + \details Sets the non-secure priority grouping field when in secure state using the required unlock sequence. + The parameter PriorityGroup is assigned to the field SCB->AIRCR [10:8] PRIGROUP field. + Only values from 0..7 are used. + In case of a conflict between priority grouping and available + priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set. + \param [in] PriorityGroup Priority grouping field. + */ +__STATIC_INLINE void TZ_NVIC_SetPriorityGrouping_NS(uint32_t PriorityGroup) +{ + uint32_t reg_value; + uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + + reg_value = SCB_NS->AIRCR; /* read old register configuration */ + reg_value &= ~((uint32_t)(SCB_AIRCR_VECTKEY_Msk | SCB_AIRCR_PRIGROUP_Msk)); /* clear bits to change */ + reg_value = (reg_value | + ((uint32_t)0x5FAUL << SCB_AIRCR_VECTKEY_Pos) | + (PriorityGroupTmp << SCB_AIRCR_PRIGROUP_Pos) ); /* Insert write key and priority group */ + SCB_NS->AIRCR = reg_value; +} + + +/** + \brief Get Priority Grouping (non-secure) + \details Reads the priority grouping field from the non-secure NVIC when in secure state. + \return Priority grouping field (SCB->AIRCR [10:8] PRIGROUP field). + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetPriorityGrouping_NS(void) +{ + return ((uint32_t)((SCB_NS->AIRCR & SCB_AIRCR_PRIGROUP_Msk) >> SCB_AIRCR_PRIGROUP_Pos)); +} + + +/** + \brief Enable Interrupt (non-secure) + \details Enables a device specific interrupt in the non-secure NVIC interrupt controller when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_EnableIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ISER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Interrupt Enable status (non-secure) + \details Returns a device specific interrupt enable status from the non-secure NVIC interrupt controller when in secure state. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetEnableIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC_NS->ISER[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Disable Interrupt (non-secure) + \details Disables a device specific interrupt in the non-secure NVIC interrupt controller when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_DisableIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ICER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Pending Interrupt (non-secure) + \details Reads the NVIC pending register in the non-secure NVIC when in secure state and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not pending. + \return 1 Interrupt status is pending. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetPendingIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC_NS->ISPR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Pending Interrupt (non-secure) + \details Sets the pending bit of a device specific interrupt in the non-secure NVIC pending register when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_SetPendingIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ISPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Clear Pending Interrupt (non-secure) + \details Clears the pending bit of a device specific interrupt in the non-secure NVIC pending register when in secure state. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void TZ_NVIC_ClearPendingIRQ_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->ICPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Active Interrupt (non-secure) + \details Reads the active register in non-secure NVIC when in secure state and returns the active bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt status is not active. + \return 1 Interrupt status is active. + \note IRQn must not be negative. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetActive_NS(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC_NS->IABR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Set Interrupt Priority (non-secure) + \details Sets the priority of a non-secure device specific interrupt or a non-secure processor exception when in secure state. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \param [in] priority Priority to set. + \note The priority cannot be set for every non-secure processor exception. + */ +__STATIC_INLINE void TZ_NVIC_SetPriority_NS(IRQn_Type IRQn, uint32_t priority) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC_NS->IPR[((uint32_t)IRQn)] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + } + else + { + SCB_NS->SHPR[(((uint32_t)IRQn) & 0xFUL) - 4UL] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + } +} + + +/** + \brief Get Interrupt Priority (non-secure) + \details Reads the priority of a non-secure device specific interrupt or a non-secure processor exception when in secure state. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Interrupt Priority. Value is aligned automatically to the implemented priority bits of the microcontroller. + */ +__STATIC_INLINE uint32_t TZ_NVIC_GetPriority_NS(IRQn_Type IRQn) +{ + + if ((int32_t)(IRQn) >= 0) + { + return (((uint32_t)NVIC_NS->IPR[((uint32_t)IRQn)] >> (8U - __NVIC_PRIO_BITS))); + } + else + { + return (((uint32_t)SCB_NS->SHPR[(((uint32_t)IRQn) & 0xFUL) - 4UL] >> (8U - __NVIC_PRIO_BITS))); + } +} +#endif /* defined (__ARM_FEATURE_CMSE) &&(__ARM_FEATURE_CMSE == 3U) */ + +/*@} end of CMSIS_Core_NVICFunctions */ + +/* ########################## MPU functions #################################### */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) + +#include "mpu_armv8.h" + +#endif + +/* ########################## FPU functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_FpuFunctions FPU Functions + \brief Function that provides FPU type. + @{ + */ + +/** + \brief get FPU type + \details returns the FPU type + \returns + - \b 0: No FPU + - \b 1: Single precision FPU + - \b 2: Double + Single precision FPU + */ +__STATIC_INLINE uint32_t SCB_GetFPUType(void) +{ + uint32_t mvfr0; + + mvfr0 = FPU->MVFR0; + + if ((mvfr0 & (FPU_MVFR0_Single_precision_Msk | FPU_MVFR0_Double_precision_Msk)) == 0x220U) + { + return 2U; /* Double + Single precision FPU */ + } + else if ((mvfr0 & (FPU_MVFR0_Single_precision_Msk | FPU_MVFR0_Double_precision_Msk)) == 0x020U) + { + return 1U; /* Single precision FPU */ + } + else + { + return 0U; /* No FPU */ + } +} + + +/*@} end of CMSIS_Core_FpuFunctions */ + + + +/* ########################## SAU functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_SAUFunctions SAU Functions + \brief Functions that configure the SAU. + @{ + */ + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) + +/** + \brief Enable SAU + \details Enables the Security Attribution Unit (SAU). + */ +__STATIC_INLINE void TZ_SAU_Enable(void) +{ + SAU->CTRL |= (SAU_CTRL_ENABLE_Msk); +} + + + +/** + \brief Disable SAU + \details Disables the Security Attribution Unit (SAU). + */ +__STATIC_INLINE void TZ_SAU_Disable(void) +{ + SAU->CTRL &= ~(SAU_CTRL_ENABLE_Msk); +} + +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + +/*@} end of CMSIS_Core_SAUFunctions */ + + + + +/* ################################## SysTick function ############################################ */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_SysTickFunctions SysTick Functions + \brief Functions that configure the System. + @{ + */ + +#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U) + +/** + \brief System Tick Configuration + \details Initializes the System Timer and its interrupt, and starts the System Tick Timer. + Counter is in free running mode to generate periodic interrupts. + \param [in] ticks Number of ticks between two interrupts. + \return 0 Function succeeded. + \return 1 Function failed. + \note When the variable __Vendor_SysTickConfig is set to 1, then the + function SysTick_Config is not included. In this case, the file device.h + must contain a vendor-specific implementation of this function. + */ +__STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks) +{ + if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk) + { + return (1UL); /* Reload value impossible */ + } + + SysTick->LOAD = (uint32_t)(ticks - 1UL); /* set reload register */ + NVIC_SetPriority (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */ + SysTick->VAL = 0UL; /* Load the SysTick Counter Value */ + SysTick->CTRL = SysTick_CTRL_CLKSOURCE_Msk | + SysTick_CTRL_TICKINT_Msk | + SysTick_CTRL_ENABLE_Msk; /* Enable SysTick IRQ and SysTick Timer */ + return (0UL); /* Function successful */ +} + +#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) +/** + \brief System Tick Configuration (non-secure) + \details Initializes the non-secure System Timer and its interrupt when in secure state, and starts the System Tick Timer. + Counter is in free running mode to generate periodic interrupts. + \param [in] ticks Number of ticks between two interrupts. + \return 0 Function succeeded. + \return 1 Function failed. + \note When the variable __Vendor_SysTickConfig is set to 1, then the + function TZ_SysTick_Config_NS is not included. In this case, the file device.h + must contain a vendor-specific implementation of this function. + + */ +__STATIC_INLINE uint32_t TZ_SysTick_Config_NS(uint32_t ticks) +{ + if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk) + { + return (1UL); /* Reload value impossible */ + } + + SysTick_NS->LOAD = (uint32_t)(ticks - 1UL); /* set reload register */ + TZ_NVIC_SetPriority_NS (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */ + SysTick_NS->VAL = 0UL; /* Load the SysTick Counter Value */ + SysTick_NS->CTRL = SysTick_CTRL_CLKSOURCE_Msk | + SysTick_CTRL_TICKINT_Msk | + SysTick_CTRL_ENABLE_Msk; /* Enable SysTick IRQ and SysTick Timer */ + return (0UL); /* Function successful */ +} +#endif /* defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) */ + +#endif + +/*@} end of CMSIS_Core_SysTickFunctions */ + + + +/* ##################################### Debug In/Output function ########################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_core_DebugFunctions ITM Functions + \brief Functions that access the ITM debug interface. + @{ + */ + +extern volatile int32_t ITM_RxBuffer; /*!< External variable to receive characters. */ +#define ITM_RXBUFFER_EMPTY ((int32_t)0x5AA55AA5U) /*!< Value identifying \ref ITM_RxBuffer is ready for next character. */ + + +/** + \brief ITM Send Character + \details Transmits a character via the ITM channel 0, and + \li Just returns when no debugger is connected that has booked the output. + \li Is blocking when a debugger is connected, but the previous character sent has not been transmitted. + \param [in] ch Character to transmit. + \returns Character to transmit. + */ +__STATIC_INLINE uint32_t ITM_SendChar (uint32_t ch) +{ + if (((ITM->TCR & ITM_TCR_ITMENA_Msk) != 0UL) && /* ITM enabled */ + ((ITM->TER & 1UL ) != 0UL) ) /* ITM Port #0 enabled */ + { + while (ITM->PORT[0U].u32 == 0UL) + { + __NOP(); + } + + ITM->PORT[0U].u8 = (uint8_t)ch; + } + + return (ch); +} + + +/** + \brief ITM Receive Character + \details Inputs a character via the external variable \ref ITM_RxBuffer. + \return Received character. + \return -1 No character pending. + */ +__STATIC_INLINE int32_t ITM_ReceiveChar (void) +{ + int32_t ch = -1; /* no character available */ + + if (ITM_RxBuffer != ITM_RXBUFFER_EMPTY) + { + ch = ITM_RxBuffer; + ITM_RxBuffer = ITM_RXBUFFER_EMPTY; /* ready for next character */ + } + + return (ch); +} + + +/** + \brief ITM Check Character + \details Checks whether a character is pending for reading in the variable \ref ITM_RxBuffer. + \return 0 No character available. + \return 1 Character available. + */ +__STATIC_INLINE int32_t ITM_CheckChar (void) +{ + + if (ITM_RxBuffer == ITM_RXBUFFER_EMPTY) + { + return (0); /* no character available */ + } + else + { + return (1); /* character available */ + } +} + +/*@} end of CMSIS_core_DebugFunctions */ + + + + +#ifdef __cplusplus +} +#endif + +#endif /* __CORE_CM33_H_DEPENDANT */ + +#endif /* __CMSIS_GENERIC */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/core_cm4.h b/EpsilonLights/Drivers/CMSIS/Include/core_cm4.h index 0e77ca9b..85d17197 100644 --- a/EpsilonLights/Drivers/CMSIS/Include/core_cm4.h +++ b/EpsilonLights/Drivers/CMSIS/Include/core_cm4.h @@ -1,40 +1,30 @@ /**************************************************************************//** * @file core_cm4.h * @brief CMSIS Cortex-M4 Core Peripheral Access Layer Header File - * @version V4.30 - * @date 20. October 2015 + * @version V5.0.8 + * @date 04. June 2018 ******************************************************************************/ -/* Copyright (c) 2009 - 2015 ARM LIMITED - - All rights reserved. - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - - Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - - Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - Neither the name of ARM nor the names of its contributors may be used - to endorse or promote products derived from this software without - specific prior written permission. - * - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE - LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR - CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF - SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS - INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN - CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) - ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE - POSSIBILITY OF SUCH DAMAGE. - ---------------------------------------------------------------------------*/ - +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ #if defined ( __ICCARM__ ) #pragma system_include /* treat file as system include file for MISRA check */ -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#elif defined (__clang__) #pragma clang system_header /* treat file as system include file */ #endif @@ -70,60 +60,22 @@ extern "C" { @{ */ -/* CMSIS CM4 definitions */ -#define __CM4_CMSIS_VERSION_MAIN (0x04U) /*!< [31:16] CMSIS HAL main version */ -#define __CM4_CMSIS_VERSION_SUB (0x1EU) /*!< [15:0] CMSIS HAL sub version */ -#define __CM4_CMSIS_VERSION ((__CM4_CMSIS_VERSION_MAIN << 16U) | \ - __CM4_CMSIS_VERSION_SUB ) /*!< CMSIS HAL version number */ - -#define __CORTEX_M (0x04U) /*!< Cortex-M Core */ - - -#if defined ( __CC_ARM ) -#define __ASM __asm /*!< asm keyword for ARM Compiler */ -#define __INLINE __inline /*!< inline keyword for ARM Compiler */ -#define __STATIC_INLINE static __inline - -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) -#define __ASM __asm /*!< asm keyword for ARM Compiler */ -#define __INLINE __inline /*!< inline keyword for ARM Compiler */ -#define __STATIC_INLINE static __inline - -#elif defined ( __GNUC__ ) -#define __ASM __asm /*!< asm keyword for GNU Compiler */ -#define __INLINE inline /*!< inline keyword for GNU Compiler */ -#define __STATIC_INLINE static inline +#include "cmsis_version.h" -#elif defined ( __ICCARM__ ) -#define __ASM __asm /*!< asm keyword for IAR Compiler */ -#define __INLINE inline /*!< inline keyword for IAR Compiler. Only available in High optimization mode! */ -#define __STATIC_INLINE static inline - -#elif defined ( __TMS470__ ) -#define __ASM __asm /*!< asm keyword for TI CCS Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __TASKING__ ) -#define __ASM __asm /*!< asm keyword for TASKING Compiler */ -#define __INLINE inline /*!< inline keyword for TASKING Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __CSMC__ ) -#define __packed -#define __ASM _asm /*!< asm keyword for COSMIC Compiler */ -#define __INLINE inline /*!< inline keyword for COSMIC Compiler. Use -pc99 on compile line */ -#define __STATIC_INLINE static inline +/* CMSIS CM4 definitions */ +#define __CM4_CMSIS_VERSION_MAIN (__CM_CMSIS_VERSION_MAIN) /*!< \deprecated [31:16] CMSIS HAL main version */ +#define __CM4_CMSIS_VERSION_SUB (__CM_CMSIS_VERSION_SUB) /*!< \deprecated [15:0] CMSIS HAL sub version */ +#define __CM4_CMSIS_VERSION ((__CM4_CMSIS_VERSION_MAIN << 16U) | \ + __CM4_CMSIS_VERSION_SUB ) /*!< \deprecated CMSIS HAL version number */ -#else -#error Unknown compiler -#endif +#define __CORTEX_M (4U) /*!< Cortex-M Core */ /** __FPU_USED indicates whether an FPU is used or not. For this, __FPU_PRESENT has to be checked prior to making use of FPU specific registers and functions. */ #if defined ( __CC_ARM ) #if defined __TARGET_FPU_VFP -#if (__FPU_PRESENT == 1U) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) #define __FPU_USED 1U #else #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" @@ -133,9 +85,9 @@ extern "C" { #define __FPU_USED 0U #endif -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) #if defined __ARM_PCS_VFP -#if (__FPU_PRESENT == 1) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) #define __FPU_USED 1U #else #warning "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" @@ -147,7 +99,7 @@ extern "C" { #elif defined ( __GNUC__ ) #if defined (__VFP_FP__) && !defined(__SOFTFP__) -#if (__FPU_PRESENT == 1U) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) #define __FPU_USED 1U #else #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" @@ -159,7 +111,7 @@ extern "C" { #elif defined ( __ICCARM__ ) #if defined __ARMVFP__ -#if (__FPU_PRESENT == 1U) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) #define __FPU_USED 1U #else #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" @@ -169,9 +121,9 @@ extern "C" { #define __FPU_USED 0U #endif -#elif defined ( __TMS470__ ) +#elif defined ( __TI_ARM__ ) #if defined __TI_VFP_SUPPORT__ -#if (__FPU_PRESENT == 1U) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) #define __FPU_USED 1U #else #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" @@ -183,7 +135,7 @@ extern "C" { #elif defined ( __TASKING__ ) #if defined __FPU_VFP__ -#if (__FPU_PRESENT == 1U) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) #define __FPU_USED 1U #else #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" @@ -195,7 +147,7 @@ extern "C" { #elif defined ( __CSMC__ ) #if ( __CSMC__ & 0x400U) -#if (__FPU_PRESENT == 1U) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) #define __FPU_USED 1U #else #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" @@ -207,9 +159,8 @@ extern "C" { #endif -#include "core_cmInstr.h" /* Core Instruction Access */ -#include "core_cmFunc.h" /* Core Function Access */ -#include "core_cmSimd.h" /* Compiler specific SIMD Intrinsics */ +#include "cmsis_compiler.h" /* CMSIS compiler specific defines */ + #ifdef __cplusplus } @@ -244,7 +195,7 @@ extern "C" { #endif #ifndef __NVIC_PRIO_BITS -#define __NVIC_PRIO_BITS 4U +#define __NVIC_PRIO_BITS 3U #warning "__NVIC_PRIO_BITS not defined in device header file; using default!" #endif @@ -367,11 +318,12 @@ typedef union struct { uint32_t ISR: 9; /*!< bit: 0.. 8 Exception number */ - uint32_t _reserved0: 7; /*!< bit: 9..15 Reserved */ + uint32_t _reserved0: 1; /*!< bit: 9 Reserved */ + uint32_t ICI_IT_1: 6; /*!< bit: 10..15 ICI/IT part 1 */ uint32_t GE: 4; /*!< bit: 16..19 Greater than or Equal flags */ uint32_t _reserved1: 4; /*!< bit: 20..23 Reserved */ - uint32_t T: 1; /*!< bit: 24 Thumb bit (read 0) */ - uint32_t IT: 2; /*!< bit: 25..26 saved IT state (read 0) */ + uint32_t T: 1; /*!< bit: 24 Thumb bit */ + uint32_t ICI_IT_2: 2; /*!< bit: 25..26 ICI/IT part 2 */ uint32_t Q: 1; /*!< bit: 27 Saturation condition flag */ uint32_t V: 1; /*!< bit: 28 Overflow condition code flag */ uint32_t C: 1; /*!< bit: 29 Carry condition code flag */ @@ -397,8 +349,8 @@ typedef union #define xPSR_Q_Pos 27U /*!< xPSR: Q Position */ #define xPSR_Q_Msk (1UL << xPSR_Q_Pos) /*!< xPSR: Q Mask */ -#define xPSR_IT_Pos 25U /*!< xPSR: IT Position */ -#define xPSR_IT_Msk (3UL << xPSR_IT_Pos) /*!< xPSR: IT Mask */ +#define xPSR_ICI_IT_2_Pos 25U /*!< xPSR: ICI/IT part 2 Position */ +#define xPSR_ICI_IT_2_Msk (3UL << xPSR_ICI_IT_2_Pos) /*!< xPSR: ICI/IT part 2 Mask */ #define xPSR_T_Pos 24U /*!< xPSR: T Position */ #define xPSR_T_Msk (1UL << xPSR_T_Pos) /*!< xPSR: T Mask */ @@ -406,6 +358,9 @@ typedef union #define xPSR_GE_Pos 16U /*!< xPSR: GE Position */ #define xPSR_GE_Msk (0xFUL << xPSR_GE_Pos) /*!< xPSR: GE Mask */ +#define xPSR_ICI_IT_1_Pos 10U /*!< xPSR: ICI/IT part 1 Position */ +#define xPSR_ICI_IT_1_Msk (0x3FUL << xPSR_ICI_IT_1_Pos) /*!< xPSR: ICI/IT part 1 Mask */ + #define xPSR_ISR_Pos 0U /*!< xPSR: ISR Position */ #define xPSR_ISR_Msk (0x1FFUL /*<< xPSR_ISR_Pos*/) /*!< xPSR: ISR Mask */ @@ -662,6 +617,66 @@ typedef struct #define SCB_CFSR_MEMFAULTSR_Pos 0U /*!< SCB CFSR: Memory Manage Fault Status Register Position */ #define SCB_CFSR_MEMFAULTSR_Msk (0xFFUL /*<< SCB_CFSR_MEMFAULTSR_Pos*/) /*!< SCB CFSR: Memory Manage Fault Status Register Mask */ +/* MemManage Fault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_MMARVALID_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 7U) /*!< SCB CFSR (MMFSR): MMARVALID Position */ +#define SCB_CFSR_MMARVALID_Msk (1UL << SCB_CFSR_MMARVALID_Pos) /*!< SCB CFSR (MMFSR): MMARVALID Mask */ + +#define SCB_CFSR_MLSPERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 5U) /*!< SCB CFSR (MMFSR): MLSPERR Position */ +#define SCB_CFSR_MLSPERR_Msk (1UL << SCB_CFSR_MLSPERR_Pos) /*!< SCB CFSR (MMFSR): MLSPERR Mask */ + +#define SCB_CFSR_MSTKERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 4U) /*!< SCB CFSR (MMFSR): MSTKERR Position */ +#define SCB_CFSR_MSTKERR_Msk (1UL << SCB_CFSR_MSTKERR_Pos) /*!< SCB CFSR (MMFSR): MSTKERR Mask */ + +#define SCB_CFSR_MUNSTKERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 3U) /*!< SCB CFSR (MMFSR): MUNSTKERR Position */ +#define SCB_CFSR_MUNSTKERR_Msk (1UL << SCB_CFSR_MUNSTKERR_Pos) /*!< SCB CFSR (MMFSR): MUNSTKERR Mask */ + +#define SCB_CFSR_DACCVIOL_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 1U) /*!< SCB CFSR (MMFSR): DACCVIOL Position */ +#define SCB_CFSR_DACCVIOL_Msk (1UL << SCB_CFSR_DACCVIOL_Pos) /*!< SCB CFSR (MMFSR): DACCVIOL Mask */ + +#define SCB_CFSR_IACCVIOL_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 0U) /*!< SCB CFSR (MMFSR): IACCVIOL Position */ +#define SCB_CFSR_IACCVIOL_Msk (1UL /*<< SCB_CFSR_IACCVIOL_Pos*/) /*!< SCB CFSR (MMFSR): IACCVIOL Mask */ + +/* BusFault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_BFARVALID_Pos (SCB_CFSR_BUSFAULTSR_Pos + 7U) /*!< SCB CFSR (BFSR): BFARVALID Position */ +#define SCB_CFSR_BFARVALID_Msk (1UL << SCB_CFSR_BFARVALID_Pos) /*!< SCB CFSR (BFSR): BFARVALID Mask */ + +#define SCB_CFSR_LSPERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 5U) /*!< SCB CFSR (BFSR): LSPERR Position */ +#define SCB_CFSR_LSPERR_Msk (1UL << SCB_CFSR_LSPERR_Pos) /*!< SCB CFSR (BFSR): LSPERR Mask */ + +#define SCB_CFSR_STKERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 4U) /*!< SCB CFSR (BFSR): STKERR Position */ +#define SCB_CFSR_STKERR_Msk (1UL << SCB_CFSR_STKERR_Pos) /*!< SCB CFSR (BFSR): STKERR Mask */ + +#define SCB_CFSR_UNSTKERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 3U) /*!< SCB CFSR (BFSR): UNSTKERR Position */ +#define SCB_CFSR_UNSTKERR_Msk (1UL << SCB_CFSR_UNSTKERR_Pos) /*!< SCB CFSR (BFSR): UNSTKERR Mask */ + +#define SCB_CFSR_IMPRECISERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 2U) /*!< SCB CFSR (BFSR): IMPRECISERR Position */ +#define SCB_CFSR_IMPRECISERR_Msk (1UL << SCB_CFSR_IMPRECISERR_Pos) /*!< SCB CFSR (BFSR): IMPRECISERR Mask */ + +#define SCB_CFSR_PRECISERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 1U) /*!< SCB CFSR (BFSR): PRECISERR Position */ +#define SCB_CFSR_PRECISERR_Msk (1UL << SCB_CFSR_PRECISERR_Pos) /*!< SCB CFSR (BFSR): PRECISERR Mask */ + +#define SCB_CFSR_IBUSERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 0U) /*!< SCB CFSR (BFSR): IBUSERR Position */ +#define SCB_CFSR_IBUSERR_Msk (1UL << SCB_CFSR_IBUSERR_Pos) /*!< SCB CFSR (BFSR): IBUSERR Mask */ + +/* UsageFault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_DIVBYZERO_Pos (SCB_CFSR_USGFAULTSR_Pos + 9U) /*!< SCB CFSR (UFSR): DIVBYZERO Position */ +#define SCB_CFSR_DIVBYZERO_Msk (1UL << SCB_CFSR_DIVBYZERO_Pos) /*!< SCB CFSR (UFSR): DIVBYZERO Mask */ + +#define SCB_CFSR_UNALIGNED_Pos (SCB_CFSR_USGFAULTSR_Pos + 8U) /*!< SCB CFSR (UFSR): UNALIGNED Position */ +#define SCB_CFSR_UNALIGNED_Msk (1UL << SCB_CFSR_UNALIGNED_Pos) /*!< SCB CFSR (UFSR): UNALIGNED Mask */ + +#define SCB_CFSR_NOCP_Pos (SCB_CFSR_USGFAULTSR_Pos + 3U) /*!< SCB CFSR (UFSR): NOCP Position */ +#define SCB_CFSR_NOCP_Msk (1UL << SCB_CFSR_NOCP_Pos) /*!< SCB CFSR (UFSR): NOCP Mask */ + +#define SCB_CFSR_INVPC_Pos (SCB_CFSR_USGFAULTSR_Pos + 2U) /*!< SCB CFSR (UFSR): INVPC Position */ +#define SCB_CFSR_INVPC_Msk (1UL << SCB_CFSR_INVPC_Pos) /*!< SCB CFSR (UFSR): INVPC Mask */ + +#define SCB_CFSR_INVSTATE_Pos (SCB_CFSR_USGFAULTSR_Pos + 1U) /*!< SCB CFSR (UFSR): INVSTATE Position */ +#define SCB_CFSR_INVSTATE_Msk (1UL << SCB_CFSR_INVSTATE_Pos) /*!< SCB CFSR (UFSR): INVSTATE Mask */ + +#define SCB_CFSR_UNDEFINSTR_Pos (SCB_CFSR_USGFAULTSR_Pos + 0U) /*!< SCB CFSR (UFSR): UNDEFINSTR Position */ +#define SCB_CFSR_UNDEFINSTR_Msk (1UL << SCB_CFSR_UNDEFINSTR_Pos) /*!< SCB CFSR (UFSR): UNDEFINSTR Mask */ + /* SCB Hard Fault Status Register Definitions */ #define SCB_HFSR_DEBUGEVT_Pos 31U /*!< SCB HFSR: DEBUGEVT Position */ #define SCB_HFSR_DEBUGEVT_Msk (1UL << SCB_HFSR_DEBUGEVT_Pos) /*!< SCB HFSR: DEBUGEVT Mask */ @@ -831,7 +846,7 @@ typedef struct /* ITM Trace Privilege Register Definitions */ #define ITM_TPR_PRIVMASK_Pos 0U /*!< ITM TPR: PRIVMASK Position */ -#define ITM_TPR_PRIVMASK_Msk (0xFUL /*<< ITM_TPR_PRIVMASK_Pos*/) /*!< ITM TPR: PRIVMASK Mask */ +#define ITM_TPR_PRIVMASK_Msk (0xFFFFFFFFUL /*<< ITM_TPR_PRIVMASK_Pos*/) /*!< ITM TPR: PRIVMASK Mask */ /* ITM Trace Control Register Definitions */ #define ITM_TCR_BUSY_Pos 23U /*!< ITM TCR: BUSY Position */ @@ -1045,7 +1060,7 @@ typedef struct */ typedef struct { - __IOM uint32_t SSPSR; /*!< Offset: 0x000 (R/ ) Supported Parallel Port Size Register */ + __IM uint32_t SSPSR; /*!< Offset: 0x000 (R/ ) Supported Parallel Port Size Register */ __IOM uint32_t CSPSR; /*!< Offset: 0x004 (R/W) Current Parallel Port Size Register */ uint32_t RESERVED0[2U]; __IOM uint32_t ACPR; /*!< Offset: 0x010 (R/W) Asynchronous Clock Prescaler Register */ @@ -1056,7 +1071,7 @@ typedef struct __IOM uint32_t FFCR; /*!< Offset: 0x304 (R/W) Formatter and Flush Control Register */ __IM uint32_t FSCR; /*!< Offset: 0x308 (R/ ) Formatter Synchronization Counter Register */ uint32_t RESERVED3[759U]; - __IM uint32_t TRIGGER; /*!< Offset: 0xEE8 (R/ ) TRIGGER */ + __IM uint32_t TRIGGER; /*!< Offset: 0xEE8 (R/ ) TRIGGER Register */ __IM uint32_t FIFO0; /*!< Offset: 0xEEC (R/ ) Integration ETM Data */ __IM uint32_t ITATBCTR2; /*!< Offset: 0xEF0 (R/ ) ITATBCTR2 */ uint32_t RESERVED4[1U]; @@ -1126,8 +1141,11 @@ typedef struct #define TPI_FIFO0_ETM0_Msk (0xFFUL /*<< TPI_FIFO0_ETM0_Pos*/) /*!< TPI FIFO0: ETM0 Mask */ /* TPI ITATBCTR2 Register Definitions */ -#define TPI_ITATBCTR2_ATREADY_Pos 0U /*!< TPI ITATBCTR2: ATREADY Position */ -#define TPI_ITATBCTR2_ATREADY_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY_Pos*/) /*!< TPI ITATBCTR2: ATREADY Mask */ +#define TPI_ITATBCTR2_ATREADY2_Pos 0U /*!< TPI ITATBCTR2: ATREADY2 Position */ +#define TPI_ITATBCTR2_ATREADY2_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY2_Pos*/) /*!< TPI ITATBCTR2: ATREADY2 Mask */ + +#define TPI_ITATBCTR2_ATREADY1_Pos 0U /*!< TPI ITATBCTR2: ATREADY1 Position */ +#define TPI_ITATBCTR2_ATREADY1_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY1_Pos*/) /*!< TPI ITATBCTR2: ATREADY1 Mask */ /* TPI Integration ITM Data Register Definitions (FIFO1) */ #define TPI_FIFO1_ITM_ATVALID_Pos 29U /*!< TPI FIFO1: ITM_ATVALID Position */ @@ -1152,12 +1170,15 @@ typedef struct #define TPI_FIFO1_ITM0_Msk (0xFFUL /*<< TPI_FIFO1_ITM0_Pos*/) /*!< TPI FIFO1: ITM0 Mask */ /* TPI ITATBCTR0 Register Definitions */ -#define TPI_ITATBCTR0_ATREADY_Pos 0U /*!< TPI ITATBCTR0: ATREADY Position */ -#define TPI_ITATBCTR0_ATREADY_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY_Pos*/) /*!< TPI ITATBCTR0: ATREADY Mask */ +#define TPI_ITATBCTR0_ATREADY2_Pos 0U /*!< TPI ITATBCTR0: ATREADY2 Position */ +#define TPI_ITATBCTR0_ATREADY2_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY2_Pos*/) /*!< TPI ITATBCTR0: ATREADY2 Mask */ + +#define TPI_ITATBCTR0_ATREADY1_Pos 0U /*!< TPI ITATBCTR0: ATREADY1 Position */ +#define TPI_ITATBCTR0_ATREADY1_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY1_Pos*/) /*!< TPI ITATBCTR0: ATREADY1 Mask */ /* TPI Integration Mode Control Register Definitions */ #define TPI_ITCTRL_Mode_Pos 0U /*!< TPI ITCTRL: Mode Position */ -#define TPI_ITCTRL_Mode_Msk (0x1UL /*<< TPI_ITCTRL_Mode_Pos*/) /*!< TPI ITCTRL: Mode Mask */ +#define TPI_ITCTRL_Mode_Msk (0x3UL /*<< TPI_ITCTRL_Mode_Pos*/) /*!< TPI ITCTRL: Mode Mask */ /* TPI DEVID Register Definitions */ #define TPI_DEVID_NRZVALID_Pos 11U /*!< TPI DEVID: NRZVALID Position */ @@ -1179,16 +1200,16 @@ typedef struct #define TPI_DEVID_NrTraceInput_Msk (0x1FUL /*<< TPI_DEVID_NrTraceInput_Pos*/) /*!< TPI DEVID: NrTraceInput Mask */ /* TPI DEVTYPE Register Definitions */ -#define TPI_DEVTYPE_MajorType_Pos 4U /*!< TPI DEVTYPE: MajorType Position */ -#define TPI_DEVTYPE_MajorType_Msk (0xFUL << TPI_DEVTYPE_MajorType_Pos) /*!< TPI DEVTYPE: MajorType Mask */ - -#define TPI_DEVTYPE_SubType_Pos 0U /*!< TPI DEVTYPE: SubType Position */ +#define TPI_DEVTYPE_SubType_Pos 4U /*!< TPI DEVTYPE: SubType Position */ #define TPI_DEVTYPE_SubType_Msk (0xFUL /*<< TPI_DEVTYPE_SubType_Pos*/) /*!< TPI DEVTYPE: SubType Mask */ +#define TPI_DEVTYPE_MajorType_Pos 0U /*!< TPI DEVTYPE: MajorType Position */ +#define TPI_DEVTYPE_MajorType_Msk (0xFUL << TPI_DEVTYPE_MajorType_Pos) /*!< TPI DEVTYPE: MajorType Mask */ + /*@}*/ /* end of group CMSIS_TPI */ -#if (__MPU_PRESENT == 1U) +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) /** \ingroup CMSIS_core_register \defgroup CMSIS_MPU Memory Protection Unit (MPU) @@ -1214,6 +1235,8 @@ typedef struct __IOM uint32_t RASR_A3; /*!< Offset: 0x028 (R/W) MPU Alias 3 Region Attribute and Size Register */ } MPU_Type; +#define MPU_TYPE_RALIASES 4U + /* MPU Type Register Definitions */ #define MPU_TYPE_IREGION_Pos 16U /*!< MPU TYPE: IREGION Position */ #define MPU_TYPE_IREGION_Msk (0xFFUL << MPU_TYPE_IREGION_Pos) /*!< MPU TYPE: IREGION Mask */ @@ -1280,10 +1303,9 @@ typedef struct #define MPU_RASR_ENABLE_Msk (1UL /*<< MPU_RASR_ENABLE_Pos*/) /*!< MPU RASR: Region enable bit Disable Mask */ /*@} end of group CMSIS_MPU */ -#endif +#endif /* defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) */ -#if (__FPU_PRESENT == 1U) /** \ingroup CMSIS_core_register \defgroup CMSIS_FPU Floating Point Unit (FPU) @@ -1388,7 +1410,6 @@ typedef struct #define FPU_MVFR1_FtZ_mode_Msk (0xFUL /*<< FPU_MVFR1_FtZ_mode_Pos*/) /*!< MVFR1: FtZ mode bits Mask */ /*@} end of group CMSIS_FPU */ -#endif /** @@ -1506,18 +1527,18 @@ typedef struct /** \brief Mask and shift a bit field value for use in a register bit range. \param[in] field Name of the register bit field. - \param[in] value Value of the bit field. + \param[in] value Value of the bit field. This parameter is interpreted as an uint32_t type. \return Masked and shifted value. */ -#define _VAL2FLD(field, value) ((value << field ## _Pos) & field ## _Msk) +#define _VAL2FLD(field, value) (((uint32_t)(value) << field ## _Pos) & field ## _Msk) /** \brief Mask and shift a register value to extract a bit filed value. \param[in] field Name of the register bit field. - \param[in] value Value of register. + \param[in] value Value of register. This parameter is interpreted as an uint32_t type. \return Masked and shifted bit field value. */ -#define _FLD2VAL(field, value) ((value & field ## _Msk) >> field ## _Pos) +#define _FLD2VAL(field, value) (((uint32_t)(value) & field ## _Msk) >> field ## _Pos) /*@} end of group CMSIS_core_bitfield */ @@ -1529,7 +1550,7 @@ typedef struct @{ */ -/* Memory mapping of Cortex-M4 Hardware */ +/* Memory mapping of Core Hardware */ #define SCS_BASE (0xE000E000UL) /*!< System Control Space Base Address */ #define ITM_BASE (0xE0000000UL) /*!< ITM Base Address */ #define DWT_BASE (0xE0001000UL) /*!< DWT Base Address */ @@ -1548,15 +1569,13 @@ typedef struct #define TPI ((TPI_Type *) TPI_BASE ) /*!< TPI configuration struct */ #define CoreDebug ((CoreDebug_Type *) CoreDebug_BASE) /*!< Core Debug configuration struct */ -#if (__MPU_PRESENT == 1U) +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) #define MPU_BASE (SCS_BASE + 0x0D90UL) /*!< Memory Protection Unit */ #define MPU ((MPU_Type *) MPU_BASE ) /*!< Memory Protection Unit */ #endif -#if (__FPU_PRESENT == 1U) -#define FPU_BASE (SCS_BASE + 0x0F30UL) /*!< Floating Point Unit */ -#define FPU ((FPU_Type *) FPU_BASE ) /*!< Floating Point Unit */ -#endif +#define FPU_BASE (SCS_BASE + 0x0F30UL) /*!< Floating Point Unit */ +#define FPU ((FPU_Type *) FPU_BASE ) /*!< Floating Point Unit */ /*@} */ @@ -1584,6 +1603,48 @@ typedef struct @{ */ +#ifdef CMSIS_NVIC_VIRTUAL +#ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE +#define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h" +#endif +#include CMSIS_NVIC_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetPriorityGrouping __NVIC_SetPriorityGrouping +#define NVIC_GetPriorityGrouping __NVIC_GetPriorityGrouping +#define NVIC_EnableIRQ __NVIC_EnableIRQ +#define NVIC_GetEnableIRQ __NVIC_GetEnableIRQ +#define NVIC_DisableIRQ __NVIC_DisableIRQ +#define NVIC_GetPendingIRQ __NVIC_GetPendingIRQ +#define NVIC_SetPendingIRQ __NVIC_SetPendingIRQ +#define NVIC_ClearPendingIRQ __NVIC_ClearPendingIRQ +#define NVIC_GetActive __NVIC_GetActive +#define NVIC_SetPriority __NVIC_SetPriority +#define NVIC_GetPriority __NVIC_GetPriority +#define NVIC_SystemReset __NVIC_SystemReset +#endif /* CMSIS_NVIC_VIRTUAL */ + +#ifdef CMSIS_VECTAB_VIRTUAL +#ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h" +#endif +#include CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetVector __NVIC_SetVector +#define NVIC_GetVector __NVIC_GetVector +#endif /* (CMSIS_VECTAB_VIRTUAL) */ + +#define NVIC_USER_IRQ_OFFSET 16 + + +/* The following EXC_RETURN values are saved the LR on exception entry */ +#define EXC_RETURN_HANDLER (0xFFFFFFF1UL) /* return to Handler mode, uses MSP after return */ +#define EXC_RETURN_THREAD_MSP (0xFFFFFFF9UL) /* return to Thread mode, uses MSP after return */ +#define EXC_RETURN_THREAD_PSP (0xFFFFFFFDUL) /* return to Thread mode, uses PSP after return */ +#define EXC_RETURN_HANDLER_FPU (0xFFFFFFE1UL) /* return to Handler mode, uses MSP after return, restore floating-point state */ +#define EXC_RETURN_THREAD_MSP_FPU (0xFFFFFFE9UL) /* return to Thread mode, uses MSP after return, restore floating-point state */ +#define EXC_RETURN_THREAD_PSP_FPU (0xFFFFFFEDUL) /* return to Thread mode, uses PSP after return, restore floating-point state */ + + /** \brief Set Priority Grouping \details Sets the priority grouping field using the required unlock sequence. @@ -1593,15 +1654,16 @@ typedef struct priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set. \param [in] PriorityGroup Priority grouping field. */ -__STATIC_INLINE void NVIC_SetPriorityGrouping(uint32_t PriorityGroup) +__STATIC_INLINE void __NVIC_SetPriorityGrouping(uint32_t PriorityGroup) { uint32_t reg_value; uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + reg_value = SCB->AIRCR; /* read old register configuration */ reg_value &= ~((uint32_t)(SCB_AIRCR_VECTKEY_Msk | SCB_AIRCR_PRIGROUP_Msk)); /* clear bits to change */ reg_value = (reg_value | ((uint32_t)0x5FAUL << SCB_AIRCR_VECTKEY_Pos) | - (PriorityGroupTmp << 8U) ); /* Insert write key and priorty group */ + (PriorityGroupTmp << SCB_AIRCR_PRIGROUP_Pos) ); /* Insert write key and priority group */ SCB->AIRCR = reg_value; } @@ -1611,120 +1673,178 @@ __STATIC_INLINE void NVIC_SetPriorityGrouping(uint32_t PriorityGroup) \details Reads the priority grouping field from the NVIC Interrupt Controller. \return Priority grouping field (SCB->AIRCR [10:8] PRIGROUP field). */ -__STATIC_INLINE uint32_t NVIC_GetPriorityGrouping(void) +__STATIC_INLINE uint32_t __NVIC_GetPriorityGrouping(void) { return ((uint32_t)((SCB->AIRCR & SCB_AIRCR_PRIGROUP_Msk) >> SCB_AIRCR_PRIGROUP_Pos)); } /** - \brief Enable External Interrupt - \details Enables a device-specific interrupt in the NVIC interrupt controller. - \param [in] IRQn External interrupt number. Value cannot be negative. + \brief Enable Interrupt + \details Enables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_EnableIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn) { - NVIC->ISER[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** - \brief Disable External Interrupt - \details Disables a device-specific interrupt in the NVIC interrupt controller. - \param [in] IRQn External interrupt number. Value cannot be negative. + \brief Get Interrupt Enable status + \details Returns a device specific interrupt enable status from the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_DisableIRQ(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn) { - NVIC->ICER[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Disable Interrupt + \details Disables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + __DSB(); + __ISB(); + } } /** \brief Get Pending Interrupt - \details Reads the pending register in the NVIC and returns the pending bit for the specified interrupt. - \param [in] IRQn Interrupt number. + \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. \return 0 Interrupt status is not pending. \return 1 Interrupt status is pending. + \note IRQn must not be negative. */ -__STATIC_INLINE uint32_t NVIC_GetPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn) { - return ((uint32_t)(((NVIC->ISPR[(((uint32_t)(int32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** \brief Set Pending Interrupt - \details Sets the pending bit of an external interrupt. - \param [in] IRQn Interrupt number. Value cannot be negative. + \details Sets the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_SetPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn) { - NVIC->ISPR[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** \brief Clear Pending Interrupt - \details Clears the pending bit of an external interrupt. - \param [in] IRQn External interrupt number. Value cannot be negative. + \details Clears the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_ClearPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn) { - NVIC->ICPR[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** \brief Get Active Interrupt - \details Reads the active register in NVIC and returns the active bit. - \param [in] IRQn Interrupt number. + \details Reads the active register in the NVIC and returns the active bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. \return 0 Interrupt status is not active. \return 1 Interrupt status is active. + \note IRQn must not be negative. */ -__STATIC_INLINE uint32_t NVIC_GetActive(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetActive(IRQn_Type IRQn) { - return ((uint32_t)(((NVIC->IABR[(((uint32_t)(int32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->IABR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** \brief Set Interrupt Priority - \details Sets the priority of an interrupt. - \note The priority cannot be set for every core interrupt. + \details Sets the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. \param [in] IRQn Interrupt number. \param [in] priority Priority to set. + \note The priority cannot be set for every processor exception. */ -__STATIC_INLINE void NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) +__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) { - if ((int32_t)(IRQn) < 0) + if ((int32_t)(IRQn) >= 0) { - SCB->SHP[(((uint32_t)(int32_t)IRQn) & 0xFUL) - 4UL] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + NVIC->IP[((uint32_t)IRQn)] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); } else { - NVIC->IP[((uint32_t)(int32_t)IRQn)] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + SCB->SHP[(((uint32_t)IRQn) & 0xFUL) - 4UL] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); } } /** \brief Get Interrupt Priority - \details Reads the priority of an interrupt. - The interrupt number can be positive to specify an external (device specific) interrupt, - or negative to specify an internal (core) interrupt. + \details Reads the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. \param [in] IRQn Interrupt number. \return Interrupt Priority. Value is aligned automatically to the implemented priority bits of the microcontroller. */ -__STATIC_INLINE uint32_t NVIC_GetPriority(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn) { - if ((int32_t)(IRQn) < 0) + + if ((int32_t)(IRQn) >= 0) { - return (((uint32_t)SCB->SHP[(((uint32_t)(int32_t)IRQn) & 0xFUL) - 4UL] >> (8U - __NVIC_PRIO_BITS))); + return (((uint32_t)NVIC->IP[((uint32_t)IRQn)] >> (8U - __NVIC_PRIO_BITS))); } else { - return (((uint32_t)NVIC->IP[((uint32_t)(int32_t)IRQn)] >> (8U - __NVIC_PRIO_BITS))); + return (((uint32_t)SCB->SHP[(((uint32_t)IRQn) & 0xFUL) - 4UL] >> (8U - __NVIC_PRIO_BITS))); } } @@ -1745,8 +1865,10 @@ __STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t P uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ uint32_t PreemptPriorityBits; uint32_t SubPriorityBits; + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + return ( ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) | ((SubPriority & (uint32_t)((1UL << (SubPriorityBits )) - 1UL))) @@ -1770,18 +1892,51 @@ __STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGr uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ uint32_t PreemptPriorityBits; uint32_t SubPriorityBits; + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL); *pSubPriority = (Priority ) & (uint32_t)((1UL << (SubPriorityBits )) - 1UL); } +/** + \brief Set Interrupt Vector + \details Sets an interrupt vector in SRAM based interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + VTOR must been relocated to SRAM before. + \param [in] IRQn Interrupt number + \param [in] vector Address of interrupt handler function + */ +__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector) +{ + uint32_t* vectors = (uint32_t*)SCB->VTOR; + vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector; +} + + +/** + \brief Get Interrupt Vector + \details Reads an interrupt vector from interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Address of interrupt handler function + */ +__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn) +{ + uint32_t* vectors = (uint32_t*)SCB->VTOR; + return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET]; +} + + /** \brief System Reset \details Initiates a system reset request to reset the MCU. */ -__STATIC_INLINE void NVIC_SystemReset(void) +__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void) { __DSB(); /* Ensure all outstanding memory accesses included buffered write are completed before reset */ @@ -1798,6 +1953,50 @@ __STATIC_INLINE void NVIC_SystemReset(void) /*@} end of CMSIS_Core_NVICFunctions */ +/* ########################## MPU functions #################################### */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) + +#include "mpu_armv7.h" + +#endif + + +/* ########################## FPU functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_FpuFunctions FPU Functions + \brief Function that provides FPU type. + @{ + */ + +/** + \brief get FPU type + \details returns the FPU type + \returns + - \b 0: No FPU + - \b 1: Single precision FPU + - \b 2: Double + Single precision FPU + */ +__STATIC_INLINE uint32_t SCB_GetFPUType(void) +{ + uint32_t mvfr0; + + mvfr0 = FPU->MVFR0; + + if ((mvfr0 & (FPU_MVFR0_Single_precision_Msk | FPU_MVFR0_Double_precision_Msk)) == 0x020U) + { + return 1U; /* Single precision FPU */ + } + else + { + return 0U; /* No FPU */ + } +} + + +/*@} end of CMSIS_Core_FpuFunctions */ + /* ################################## SysTick function ############################################ */ @@ -1808,7 +2007,7 @@ __STATIC_INLINE void NVIC_SystemReset(void) @{ */ -#if (__Vendor_SysTickConfig == 0U) +#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U) /** \brief System Tick Configuration @@ -1851,8 +2050,8 @@ __STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks) @{ */ -extern volatile int32_t ITM_RxBuffer; /*!< External variable to receive characters. */ -#define ITM_RXBUFFER_EMPTY 0x5AA55AA5U /*!< Value identifying \ref ITM_RxBuffer is ready for next character. */ +extern volatile int32_t ITM_RxBuffer; /*!< External variable to receive characters. */ +#define ITM_RXBUFFER_EMPTY ((int32_t)0x5AA55AA5U) /*!< Value identifying \ref ITM_RxBuffer is ready for next character. */ /** @@ -1908,6 +2107,7 @@ __STATIC_INLINE int32_t ITM_ReceiveChar (void) */ __STATIC_INLINE int32_t ITM_CheckChar (void) { + if (ITM_RxBuffer == ITM_RXBUFFER_EMPTY) { return (0); /* no character available */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/core_cm7.h b/EpsilonLights/Drivers/CMSIS/Include/core_cm7.h index 757231af..7328410b 100644 --- a/EpsilonLights/Drivers/CMSIS/Include/core_cm7.h +++ b/EpsilonLights/Drivers/CMSIS/Include/core_cm7.h @@ -1,40 +1,30 @@ /**************************************************************************//** * @file core_cm7.h * @brief CMSIS Cortex-M7 Core Peripheral Access Layer Header File - * @version V4.30 - * @date 20. October 2015 + * @version V5.0.8 + * @date 04. June 2018 ******************************************************************************/ -/* Copyright (c) 2009 - 2015 ARM LIMITED - - All rights reserved. - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - - Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - - Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - Neither the name of ARM nor the names of its contributors may be used - to endorse or promote products derived from this software without - specific prior written permission. - * - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE - LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR - CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF - SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS - INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN - CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) - ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE - POSSIBILITY OF SUCH DAMAGE. - ---------------------------------------------------------------------------*/ - +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ #if defined ( __ICCARM__ ) #pragma system_include /* treat file as system include file for MISRA check */ -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#elif defined (__clang__) #pragma clang system_header /* treat file as system include file */ #endif @@ -70,60 +60,22 @@ extern "C" { @{ */ -/* CMSIS CM7 definitions */ -#define __CM7_CMSIS_VERSION_MAIN (0x04U) /*!< [31:16] CMSIS HAL main version */ -#define __CM7_CMSIS_VERSION_SUB (0x1EU) /*!< [15:0] CMSIS HAL sub version */ -#define __CM7_CMSIS_VERSION ((__CM7_CMSIS_VERSION_MAIN << 16U) | \ - __CM7_CMSIS_VERSION_SUB ) /*!< CMSIS HAL version number */ - -#define __CORTEX_M (0x07U) /*!< Cortex-M Core */ - - -#if defined ( __CC_ARM ) -#define __ASM __asm /*!< asm keyword for ARM Compiler */ -#define __INLINE __inline /*!< inline keyword for ARM Compiler */ -#define __STATIC_INLINE static __inline - -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) -#define __ASM __asm /*!< asm keyword for ARM Compiler */ -#define __INLINE __inline /*!< inline keyword for ARM Compiler */ -#define __STATIC_INLINE static __inline - -#elif defined ( __GNUC__ ) -#define __ASM __asm /*!< asm keyword for GNU Compiler */ -#define __INLINE inline /*!< inline keyword for GNU Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __ICCARM__ ) -#define __ASM __asm /*!< asm keyword for IAR Compiler */ -#define __INLINE inline /*!< inline keyword for IAR Compiler. Only available in High optimization mode! */ -#define __STATIC_INLINE static inline - -#elif defined ( __TMS470__ ) -#define __ASM __asm /*!< asm keyword for TI CCS Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __TASKING__ ) -#define __ASM __asm /*!< asm keyword for TASKING Compiler */ -#define __INLINE inline /*!< inline keyword for TASKING Compiler */ -#define __STATIC_INLINE static inline +#include "cmsis_version.h" -#elif defined ( __CSMC__ ) -#define __packed -#define __ASM _asm /*!< asm keyword for COSMIC Compiler */ -#define __INLINE inline /*!< inline keyword for COSMIC Compiler. Use -pc99 on compile line */ -#define __STATIC_INLINE static inline +/* CMSIS CM7 definitions */ +#define __CM7_CMSIS_VERSION_MAIN (__CM_CMSIS_VERSION_MAIN) /*!< \deprecated [31:16] CMSIS HAL main version */ +#define __CM7_CMSIS_VERSION_SUB ( __CM_CMSIS_VERSION_SUB) /*!< \deprecated [15:0] CMSIS HAL sub version */ +#define __CM7_CMSIS_VERSION ((__CM7_CMSIS_VERSION_MAIN << 16U) | \ + __CM7_CMSIS_VERSION_SUB ) /*!< \deprecated CMSIS HAL version number */ -#else -#error Unknown compiler -#endif +#define __CORTEX_M (7U) /*!< Cortex-M Core */ /** __FPU_USED indicates whether an FPU is used or not. For this, __FPU_PRESENT has to be checked prior to making use of FPU specific registers and functions. */ #if defined ( __CC_ARM ) #if defined __TARGET_FPU_VFP -#if (__FPU_PRESENT == 1U) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) #define __FPU_USED 1U #else #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" @@ -133,9 +85,9 @@ extern "C" { #define __FPU_USED 0U #endif -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) #if defined __ARM_PCS_VFP -#if (__FPU_PRESENT == 1) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) #define __FPU_USED 1U #else #warning "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" @@ -147,7 +99,7 @@ extern "C" { #elif defined ( __GNUC__ ) #if defined (__VFP_FP__) && !defined(__SOFTFP__) -#if (__FPU_PRESENT == 1U) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) #define __FPU_USED 1U #else #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" @@ -159,7 +111,7 @@ extern "C" { #elif defined ( __ICCARM__ ) #if defined __ARMVFP__ -#if (__FPU_PRESENT == 1U) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) #define __FPU_USED 1U #else #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" @@ -169,9 +121,9 @@ extern "C" { #define __FPU_USED 0U #endif -#elif defined ( __TMS470__ ) +#elif defined ( __TI_ARM__ ) #if defined __TI_VFP_SUPPORT__ -#if (__FPU_PRESENT == 1U) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) #define __FPU_USED 1U #else #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" @@ -183,7 +135,7 @@ extern "C" { #elif defined ( __TASKING__ ) #if defined __FPU_VFP__ -#if (__FPU_PRESENT == 1U) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) #define __FPU_USED 1U #else #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" @@ -195,7 +147,7 @@ extern "C" { #elif defined ( __CSMC__ ) #if ( __CSMC__ & 0x400U) -#if (__FPU_PRESENT == 1U) +#if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U) #define __FPU_USED 1U #else #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" @@ -207,9 +159,8 @@ extern "C" { #endif -#include "core_cmInstr.h" /* Core Instruction Access */ -#include "core_cmFunc.h" /* Core Function Access */ -#include "core_cmSimd.h" /* Compiler specific SIMD Intrinsics */ +#include "cmsis_compiler.h" /* CMSIS compiler specific defines */ + #ifdef __cplusplus } @@ -382,11 +333,12 @@ typedef union struct { uint32_t ISR: 9; /*!< bit: 0.. 8 Exception number */ - uint32_t _reserved0: 7; /*!< bit: 9..15 Reserved */ + uint32_t _reserved0: 1; /*!< bit: 9 Reserved */ + uint32_t ICI_IT_1: 6; /*!< bit: 10..15 ICI/IT part 1 */ uint32_t GE: 4; /*!< bit: 16..19 Greater than or Equal flags */ uint32_t _reserved1: 4; /*!< bit: 20..23 Reserved */ - uint32_t T: 1; /*!< bit: 24 Thumb bit (read 0) */ - uint32_t IT: 2; /*!< bit: 25..26 saved IT state (read 0) */ + uint32_t T: 1; /*!< bit: 24 Thumb bit */ + uint32_t ICI_IT_2: 2; /*!< bit: 25..26 ICI/IT part 2 */ uint32_t Q: 1; /*!< bit: 27 Saturation condition flag */ uint32_t V: 1; /*!< bit: 28 Overflow condition code flag */ uint32_t C: 1; /*!< bit: 29 Carry condition code flag */ @@ -412,8 +364,8 @@ typedef union #define xPSR_Q_Pos 27U /*!< xPSR: Q Position */ #define xPSR_Q_Msk (1UL << xPSR_Q_Pos) /*!< xPSR: Q Mask */ -#define xPSR_IT_Pos 25U /*!< xPSR: IT Position */ -#define xPSR_IT_Msk (3UL << xPSR_IT_Pos) /*!< xPSR: IT Mask */ +#define xPSR_ICI_IT_2_Pos 25U /*!< xPSR: ICI/IT part 2 Position */ +#define xPSR_ICI_IT_2_Msk (3UL << xPSR_ICI_IT_2_Pos) /*!< xPSR: ICI/IT part 2 Mask */ #define xPSR_T_Pos 24U /*!< xPSR: T Position */ #define xPSR_T_Msk (1UL << xPSR_T_Pos) /*!< xPSR: T Mask */ @@ -421,6 +373,9 @@ typedef union #define xPSR_GE_Pos 16U /*!< xPSR: GE Position */ #define xPSR_GE_Msk (0xFUL << xPSR_GE_Pos) /*!< xPSR: GE Mask */ +#define xPSR_ICI_IT_1_Pos 10U /*!< xPSR: ICI/IT part 1 Position */ +#define xPSR_ICI_IT_1_Msk (0x3FUL << xPSR_ICI_IT_1_Pos) /*!< xPSR: ICI/IT part 1 Mask */ + #define xPSR_ISR_Pos 0U /*!< xPSR: ISR Position */ #define xPSR_ISR_Msk (0x1FFUL /*<< xPSR_ISR_Pos*/) /*!< xPSR: ISR Mask */ @@ -529,7 +484,7 @@ typedef struct uint32_t RESERVED4[15U]; __IM uint32_t MVFR0; /*!< Offset: 0x240 (R/ ) Media and VFP Feature Register 0 */ __IM uint32_t MVFR1; /*!< Offset: 0x244 (R/ ) Media and VFP Feature Register 1 */ - __IM uint32_t MVFR2; /*!< Offset: 0x248 (R/ ) Media and VFP Feature Register 1 */ + __IM uint32_t MVFR2; /*!< Offset: 0x248 (R/ ) Media and VFP Feature Register 2 */ uint32_t RESERVED5[1U]; __OM uint32_t ICIALLU; /*!< Offset: 0x250 ( /W) I-Cache Invalidate All to PoU */ uint32_t RESERVED6[1U]; @@ -715,6 +670,66 @@ typedef struct #define SCB_CFSR_MEMFAULTSR_Pos 0U /*!< SCB CFSR: Memory Manage Fault Status Register Position */ #define SCB_CFSR_MEMFAULTSR_Msk (0xFFUL /*<< SCB_CFSR_MEMFAULTSR_Pos*/) /*!< SCB CFSR: Memory Manage Fault Status Register Mask */ +/* MemManage Fault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_MMARVALID_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 7U) /*!< SCB CFSR (MMFSR): MMARVALID Position */ +#define SCB_CFSR_MMARVALID_Msk (1UL << SCB_CFSR_MMARVALID_Pos) /*!< SCB CFSR (MMFSR): MMARVALID Mask */ + +#define SCB_CFSR_MLSPERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 5U) /*!< SCB CFSR (MMFSR): MLSPERR Position */ +#define SCB_CFSR_MLSPERR_Msk (1UL << SCB_CFSR_MLSPERR_Pos) /*!< SCB CFSR (MMFSR): MLSPERR Mask */ + +#define SCB_CFSR_MSTKERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 4U) /*!< SCB CFSR (MMFSR): MSTKERR Position */ +#define SCB_CFSR_MSTKERR_Msk (1UL << SCB_CFSR_MSTKERR_Pos) /*!< SCB CFSR (MMFSR): MSTKERR Mask */ + +#define SCB_CFSR_MUNSTKERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 3U) /*!< SCB CFSR (MMFSR): MUNSTKERR Position */ +#define SCB_CFSR_MUNSTKERR_Msk (1UL << SCB_CFSR_MUNSTKERR_Pos) /*!< SCB CFSR (MMFSR): MUNSTKERR Mask */ + +#define SCB_CFSR_DACCVIOL_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 1U) /*!< SCB CFSR (MMFSR): DACCVIOL Position */ +#define SCB_CFSR_DACCVIOL_Msk (1UL << SCB_CFSR_DACCVIOL_Pos) /*!< SCB CFSR (MMFSR): DACCVIOL Mask */ + +#define SCB_CFSR_IACCVIOL_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 0U) /*!< SCB CFSR (MMFSR): IACCVIOL Position */ +#define SCB_CFSR_IACCVIOL_Msk (1UL /*<< SCB_CFSR_IACCVIOL_Pos*/) /*!< SCB CFSR (MMFSR): IACCVIOL Mask */ + +/* BusFault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_BFARVALID_Pos (SCB_CFSR_BUSFAULTSR_Pos + 7U) /*!< SCB CFSR (BFSR): BFARVALID Position */ +#define SCB_CFSR_BFARVALID_Msk (1UL << SCB_CFSR_BFARVALID_Pos) /*!< SCB CFSR (BFSR): BFARVALID Mask */ + +#define SCB_CFSR_LSPERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 5U) /*!< SCB CFSR (BFSR): LSPERR Position */ +#define SCB_CFSR_LSPERR_Msk (1UL << SCB_CFSR_LSPERR_Pos) /*!< SCB CFSR (BFSR): LSPERR Mask */ + +#define SCB_CFSR_STKERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 4U) /*!< SCB CFSR (BFSR): STKERR Position */ +#define SCB_CFSR_STKERR_Msk (1UL << SCB_CFSR_STKERR_Pos) /*!< SCB CFSR (BFSR): STKERR Mask */ + +#define SCB_CFSR_UNSTKERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 3U) /*!< SCB CFSR (BFSR): UNSTKERR Position */ +#define SCB_CFSR_UNSTKERR_Msk (1UL << SCB_CFSR_UNSTKERR_Pos) /*!< SCB CFSR (BFSR): UNSTKERR Mask */ + +#define SCB_CFSR_IMPRECISERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 2U) /*!< SCB CFSR (BFSR): IMPRECISERR Position */ +#define SCB_CFSR_IMPRECISERR_Msk (1UL << SCB_CFSR_IMPRECISERR_Pos) /*!< SCB CFSR (BFSR): IMPRECISERR Mask */ + +#define SCB_CFSR_PRECISERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 1U) /*!< SCB CFSR (BFSR): PRECISERR Position */ +#define SCB_CFSR_PRECISERR_Msk (1UL << SCB_CFSR_PRECISERR_Pos) /*!< SCB CFSR (BFSR): PRECISERR Mask */ + +#define SCB_CFSR_IBUSERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 0U) /*!< SCB CFSR (BFSR): IBUSERR Position */ +#define SCB_CFSR_IBUSERR_Msk (1UL << SCB_CFSR_IBUSERR_Pos) /*!< SCB CFSR (BFSR): IBUSERR Mask */ + +/* UsageFault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_DIVBYZERO_Pos (SCB_CFSR_USGFAULTSR_Pos + 9U) /*!< SCB CFSR (UFSR): DIVBYZERO Position */ +#define SCB_CFSR_DIVBYZERO_Msk (1UL << SCB_CFSR_DIVBYZERO_Pos) /*!< SCB CFSR (UFSR): DIVBYZERO Mask */ + +#define SCB_CFSR_UNALIGNED_Pos (SCB_CFSR_USGFAULTSR_Pos + 8U) /*!< SCB CFSR (UFSR): UNALIGNED Position */ +#define SCB_CFSR_UNALIGNED_Msk (1UL << SCB_CFSR_UNALIGNED_Pos) /*!< SCB CFSR (UFSR): UNALIGNED Mask */ + +#define SCB_CFSR_NOCP_Pos (SCB_CFSR_USGFAULTSR_Pos + 3U) /*!< SCB CFSR (UFSR): NOCP Position */ +#define SCB_CFSR_NOCP_Msk (1UL << SCB_CFSR_NOCP_Pos) /*!< SCB CFSR (UFSR): NOCP Mask */ + +#define SCB_CFSR_INVPC_Pos (SCB_CFSR_USGFAULTSR_Pos + 2U) /*!< SCB CFSR (UFSR): INVPC Position */ +#define SCB_CFSR_INVPC_Msk (1UL << SCB_CFSR_INVPC_Pos) /*!< SCB CFSR (UFSR): INVPC Mask */ + +#define SCB_CFSR_INVSTATE_Pos (SCB_CFSR_USGFAULTSR_Pos + 1U) /*!< SCB CFSR (UFSR): INVSTATE Position */ +#define SCB_CFSR_INVSTATE_Msk (1UL << SCB_CFSR_INVSTATE_Pos) /*!< SCB CFSR (UFSR): INVSTATE Mask */ + +#define SCB_CFSR_UNDEFINSTR_Pos (SCB_CFSR_USGFAULTSR_Pos + 0U) /*!< SCB CFSR (UFSR): UNDEFINSTR Position */ +#define SCB_CFSR_UNDEFINSTR_Msk (1UL << SCB_CFSR_UNDEFINSTR_Pos) /*!< SCB CFSR (UFSR): UNDEFINSTR Mask */ + /* SCB Hard Fault Status Register Definitions */ #define SCB_HFSR_DEBUGEVT_Pos 31U /*!< SCB HFSR: DEBUGEVT Position */ #define SCB_HFSR_DEBUGEVT_Msk (1UL << SCB_HFSR_DEBUGEVT_Pos) /*!< SCB HFSR: DEBUGEVT Mask */ @@ -1033,7 +1048,7 @@ typedef struct /* ITM Trace Privilege Register Definitions */ #define ITM_TPR_PRIVMASK_Pos 0U /*!< ITM TPR: PRIVMASK Position */ -#define ITM_TPR_PRIVMASK_Msk (0xFUL /*<< ITM_TPR_PRIVMASK_Pos*/) /*!< ITM TPR: PRIVMASK Mask */ +#define ITM_TPR_PRIVMASK_Msk (0xFFFFFFFFUL /*<< ITM_TPR_PRIVMASK_Pos*/) /*!< ITM TPR: PRIVMASK Mask */ /* ITM Trace Control Register Definitions */ #define ITM_TCR_BUSY_Pos 23U /*!< ITM TCR: BUSY Position */ @@ -1250,7 +1265,7 @@ typedef struct */ typedef struct { - __IOM uint32_t SSPSR; /*!< Offset: 0x000 (R/ ) Supported Parallel Port Size Register */ + __IM uint32_t SSPSR; /*!< Offset: 0x000 (R/ ) Supported Parallel Port Size Register */ __IOM uint32_t CSPSR; /*!< Offset: 0x004 (R/W) Current Parallel Port Size Register */ uint32_t RESERVED0[2U]; __IOM uint32_t ACPR; /*!< Offset: 0x010 (R/W) Asynchronous Clock Prescaler Register */ @@ -1261,7 +1276,7 @@ typedef struct __IOM uint32_t FFCR; /*!< Offset: 0x304 (R/W) Formatter and Flush Control Register */ __IM uint32_t FSCR; /*!< Offset: 0x308 (R/ ) Formatter Synchronization Counter Register */ uint32_t RESERVED3[759U]; - __IM uint32_t TRIGGER; /*!< Offset: 0xEE8 (R/ ) TRIGGER */ + __IM uint32_t TRIGGER; /*!< Offset: 0xEE8 (R/ ) TRIGGER Register */ __IM uint32_t FIFO0; /*!< Offset: 0xEEC (R/ ) Integration ETM Data */ __IM uint32_t ITATBCTR2; /*!< Offset: 0xEF0 (R/ ) ITATBCTR2 */ uint32_t RESERVED4[1U]; @@ -1331,8 +1346,11 @@ typedef struct #define TPI_FIFO0_ETM0_Msk (0xFFUL /*<< TPI_FIFO0_ETM0_Pos*/) /*!< TPI FIFO0: ETM0 Mask */ /* TPI ITATBCTR2 Register Definitions */ -#define TPI_ITATBCTR2_ATREADY_Pos 0U /*!< TPI ITATBCTR2: ATREADY Position */ -#define TPI_ITATBCTR2_ATREADY_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY_Pos*/) /*!< TPI ITATBCTR2: ATREADY Mask */ +#define TPI_ITATBCTR2_ATREADY2_Pos 0U /*!< TPI ITATBCTR2: ATREADY2 Position */ +#define TPI_ITATBCTR2_ATREADY2_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY2_Pos*/) /*!< TPI ITATBCTR2: ATREADY2 Mask */ + +#define TPI_ITATBCTR2_ATREADY1_Pos 0U /*!< TPI ITATBCTR2: ATREADY1 Position */ +#define TPI_ITATBCTR2_ATREADY1_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY1_Pos*/) /*!< TPI ITATBCTR2: ATREADY1 Mask */ /* TPI Integration ITM Data Register Definitions (FIFO1) */ #define TPI_FIFO1_ITM_ATVALID_Pos 29U /*!< TPI FIFO1: ITM_ATVALID Position */ @@ -1357,12 +1375,15 @@ typedef struct #define TPI_FIFO1_ITM0_Msk (0xFFUL /*<< TPI_FIFO1_ITM0_Pos*/) /*!< TPI FIFO1: ITM0 Mask */ /* TPI ITATBCTR0 Register Definitions */ -#define TPI_ITATBCTR0_ATREADY_Pos 0U /*!< TPI ITATBCTR0: ATREADY Position */ -#define TPI_ITATBCTR0_ATREADY_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY_Pos*/) /*!< TPI ITATBCTR0: ATREADY Mask */ +#define TPI_ITATBCTR0_ATREADY2_Pos 0U /*!< TPI ITATBCTR0: ATREADY2 Position */ +#define TPI_ITATBCTR0_ATREADY2_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY2_Pos*/) /*!< TPI ITATBCTR0: ATREADY2 Mask */ + +#define TPI_ITATBCTR0_ATREADY1_Pos 0U /*!< TPI ITATBCTR0: ATREADY1 Position */ +#define TPI_ITATBCTR0_ATREADY1_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY1_Pos*/) /*!< TPI ITATBCTR0: ATREADY1 Mask */ /* TPI Integration Mode Control Register Definitions */ #define TPI_ITCTRL_Mode_Pos 0U /*!< TPI ITCTRL: Mode Position */ -#define TPI_ITCTRL_Mode_Msk (0x1UL /*<< TPI_ITCTRL_Mode_Pos*/) /*!< TPI ITCTRL: Mode Mask */ +#define TPI_ITCTRL_Mode_Msk (0x3UL /*<< TPI_ITCTRL_Mode_Pos*/) /*!< TPI ITCTRL: Mode Mask */ /* TPI DEVID Register Definitions */ #define TPI_DEVID_NRZVALID_Pos 11U /*!< TPI DEVID: NRZVALID Position */ @@ -1384,16 +1405,16 @@ typedef struct #define TPI_DEVID_NrTraceInput_Msk (0x1FUL /*<< TPI_DEVID_NrTraceInput_Pos*/) /*!< TPI DEVID: NrTraceInput Mask */ /* TPI DEVTYPE Register Definitions */ -#define TPI_DEVTYPE_MajorType_Pos 4U /*!< TPI DEVTYPE: MajorType Position */ -#define TPI_DEVTYPE_MajorType_Msk (0xFUL << TPI_DEVTYPE_MajorType_Pos) /*!< TPI DEVTYPE: MajorType Mask */ - -#define TPI_DEVTYPE_SubType_Pos 0U /*!< TPI DEVTYPE: SubType Position */ +#define TPI_DEVTYPE_SubType_Pos 4U /*!< TPI DEVTYPE: SubType Position */ #define TPI_DEVTYPE_SubType_Msk (0xFUL /*<< TPI_DEVTYPE_SubType_Pos*/) /*!< TPI DEVTYPE: SubType Mask */ +#define TPI_DEVTYPE_MajorType_Pos 0U /*!< TPI DEVTYPE: MajorType Position */ +#define TPI_DEVTYPE_MajorType_Msk (0xFUL << TPI_DEVTYPE_MajorType_Pos) /*!< TPI DEVTYPE: MajorType Mask */ + /*@}*/ /* end of group CMSIS_TPI */ -#if (__MPU_PRESENT == 1U) +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) /** \ingroup CMSIS_core_register \defgroup CMSIS_MPU Memory Protection Unit (MPU) @@ -1419,6 +1440,8 @@ typedef struct __IOM uint32_t RASR_A3; /*!< Offset: 0x028 (R/W) MPU Alias 3 Region Attribute and Size Register */ } MPU_Type; +#define MPU_TYPE_RALIASES 4U + /* MPU Type Register Definitions */ #define MPU_TYPE_IREGION_Pos 16U /*!< MPU TYPE: IREGION Position */ #define MPU_TYPE_IREGION_Msk (0xFFUL << MPU_TYPE_IREGION_Pos) /*!< MPU TYPE: IREGION Mask */ @@ -1485,10 +1508,9 @@ typedef struct #define MPU_RASR_ENABLE_Msk (1UL /*<< MPU_RASR_ENABLE_Pos*/) /*!< MPU RASR: Region enable bit Disable Mask */ /*@} end of group CMSIS_MPU */ -#endif +#endif /* defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) */ -#if (__FPU_PRESENT == 1U) /** \ingroup CMSIS_core_register \defgroup CMSIS_FPU Floating Point Unit (FPU) @@ -1596,7 +1618,6 @@ typedef struct /* Media and FP Feature Register 2 Definitions */ /*@} end of group CMSIS_FPU */ -#endif /** @@ -1714,18 +1735,18 @@ typedef struct /** \brief Mask and shift a bit field value for use in a register bit range. \param[in] field Name of the register bit field. - \param[in] value Value of the bit field. + \param[in] value Value of the bit field. This parameter is interpreted as an uint32_t type. \return Masked and shifted value. */ -#define _VAL2FLD(field, value) ((value << field ## _Pos) & field ## _Msk) +#define _VAL2FLD(field, value) (((uint32_t)(value) << field ## _Pos) & field ## _Msk) /** \brief Mask and shift a register value to extract a bit filed value. \param[in] field Name of the register bit field. - \param[in] value Value of register. + \param[in] value Value of register. This parameter is interpreted as an uint32_t type. \return Masked and shifted bit field value. */ -#define _FLD2VAL(field, value) ((value & field ## _Msk) >> field ## _Pos) +#define _FLD2VAL(field, value) (((uint32_t)(value) & field ## _Msk) >> field ## _Pos) /*@} end of group CMSIS_core_bitfield */ @@ -1737,7 +1758,7 @@ typedef struct @{ */ -/* Memory mapping of Cortex-M4 Hardware */ +/* Memory mapping of Core Hardware */ #define SCS_BASE (0xE000E000UL) /*!< System Control Space Base Address */ #define ITM_BASE (0xE0000000UL) /*!< ITM Base Address */ #define DWT_BASE (0xE0001000UL) /*!< DWT Base Address */ @@ -1756,15 +1777,13 @@ typedef struct #define TPI ((TPI_Type *) TPI_BASE ) /*!< TPI configuration struct */ #define CoreDebug ((CoreDebug_Type *) CoreDebug_BASE) /*!< Core Debug configuration struct */ -#if (__MPU_PRESENT == 1U) +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) #define MPU_BASE (SCS_BASE + 0x0D90UL) /*!< Memory Protection Unit */ #define MPU ((MPU_Type *) MPU_BASE ) /*!< Memory Protection Unit */ #endif -#if (__FPU_PRESENT == 1U) -#define FPU_BASE (SCS_BASE + 0x0F30UL) /*!< Floating Point Unit */ -#define FPU ((FPU_Type *) FPU_BASE ) /*!< Floating Point Unit */ -#endif +#define FPU_BASE (SCS_BASE + 0x0F30UL) /*!< Floating Point Unit */ +#define FPU ((FPU_Type *) FPU_BASE ) /*!< Floating Point Unit */ /*@} */ @@ -1792,6 +1811,48 @@ typedef struct @{ */ +#ifdef CMSIS_NVIC_VIRTUAL +#ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE +#define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h" +#endif +#include CMSIS_NVIC_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetPriorityGrouping __NVIC_SetPriorityGrouping +#define NVIC_GetPriorityGrouping __NVIC_GetPriorityGrouping +#define NVIC_EnableIRQ __NVIC_EnableIRQ +#define NVIC_GetEnableIRQ __NVIC_GetEnableIRQ +#define NVIC_DisableIRQ __NVIC_DisableIRQ +#define NVIC_GetPendingIRQ __NVIC_GetPendingIRQ +#define NVIC_SetPendingIRQ __NVIC_SetPendingIRQ +#define NVIC_ClearPendingIRQ __NVIC_ClearPendingIRQ +#define NVIC_GetActive __NVIC_GetActive +#define NVIC_SetPriority __NVIC_SetPriority +#define NVIC_GetPriority __NVIC_GetPriority +#define NVIC_SystemReset __NVIC_SystemReset +#endif /* CMSIS_NVIC_VIRTUAL */ + +#ifdef CMSIS_VECTAB_VIRTUAL +#ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h" +#endif +#include CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetVector __NVIC_SetVector +#define NVIC_GetVector __NVIC_GetVector +#endif /* (CMSIS_VECTAB_VIRTUAL) */ + +#define NVIC_USER_IRQ_OFFSET 16 + + +/* The following EXC_RETURN values are saved the LR on exception entry */ +#define EXC_RETURN_HANDLER (0xFFFFFFF1UL) /* return to Handler mode, uses MSP after return */ +#define EXC_RETURN_THREAD_MSP (0xFFFFFFF9UL) /* return to Thread mode, uses MSP after return */ +#define EXC_RETURN_THREAD_PSP (0xFFFFFFFDUL) /* return to Thread mode, uses PSP after return */ +#define EXC_RETURN_HANDLER_FPU (0xFFFFFFE1UL) /* return to Handler mode, uses MSP after return, restore floating-point state */ +#define EXC_RETURN_THREAD_MSP_FPU (0xFFFFFFE9UL) /* return to Thread mode, uses MSP after return, restore floating-point state */ +#define EXC_RETURN_THREAD_PSP_FPU (0xFFFFFFEDUL) /* return to Thread mode, uses PSP after return, restore floating-point state */ + + /** \brief Set Priority Grouping \details Sets the priority grouping field using the required unlock sequence. @@ -1801,15 +1862,16 @@ typedef struct priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set. \param [in] PriorityGroup Priority grouping field. */ -__STATIC_INLINE void NVIC_SetPriorityGrouping(uint32_t PriorityGroup) +__STATIC_INLINE void __NVIC_SetPriorityGrouping(uint32_t PriorityGroup) { uint32_t reg_value; uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + reg_value = SCB->AIRCR; /* read old register configuration */ reg_value &= ~((uint32_t)(SCB_AIRCR_VECTKEY_Msk | SCB_AIRCR_PRIGROUP_Msk)); /* clear bits to change */ reg_value = (reg_value | ((uint32_t)0x5FAUL << SCB_AIRCR_VECTKEY_Pos) | - (PriorityGroupTmp << 8U) ); /* Insert write key and priorty group */ + (PriorityGroupTmp << SCB_AIRCR_PRIGROUP_Pos) ); /* Insert write key and priority group */ SCB->AIRCR = reg_value; } @@ -1819,120 +1881,178 @@ __STATIC_INLINE void NVIC_SetPriorityGrouping(uint32_t PriorityGroup) \details Reads the priority grouping field from the NVIC Interrupt Controller. \return Priority grouping field (SCB->AIRCR [10:8] PRIGROUP field). */ -__STATIC_INLINE uint32_t NVIC_GetPriorityGrouping(void) +__STATIC_INLINE uint32_t __NVIC_GetPriorityGrouping(void) { return ((uint32_t)((SCB->AIRCR & SCB_AIRCR_PRIGROUP_Msk) >> SCB_AIRCR_PRIGROUP_Pos)); } /** - \brief Enable External Interrupt - \details Enables a device-specific interrupt in the NVIC interrupt controller. - \param [in] IRQn External interrupt number. Value cannot be negative. + \brief Enable Interrupt + \details Enables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_EnableIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn) { - NVIC->ISER[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** - \brief Disable External Interrupt - \details Disables a device-specific interrupt in the NVIC interrupt controller. - \param [in] IRQn External interrupt number. Value cannot be negative. + \brief Get Interrupt Enable status + \details Returns a device specific interrupt enable status from the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_DisableIRQ(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn) { - NVIC->ICER[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } +} + + +/** + \brief Disable Interrupt + \details Disables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + __DSB(); + __ISB(); + } } /** \brief Get Pending Interrupt - \details Reads the pending register in the NVIC and returns the pending bit for the specified interrupt. - \param [in] IRQn Interrupt number. + \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. \return 0 Interrupt status is not pending. \return 1 Interrupt status is pending. + \note IRQn must not be negative. */ -__STATIC_INLINE uint32_t NVIC_GetPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn) { - return ((uint32_t)(((NVIC->ISPR[(((uint32_t)(int32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** \brief Set Pending Interrupt - \details Sets the pending bit of an external interrupt. - \param [in] IRQn Interrupt number. Value cannot be negative. + \details Sets the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_SetPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn) { - NVIC->ISPR[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** \brief Clear Pending Interrupt - \details Clears the pending bit of an external interrupt. - \param [in] IRQn External interrupt number. Value cannot be negative. + \details Clears the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_ClearPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn) { - NVIC->ICPR[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** \brief Get Active Interrupt - \details Reads the active register in NVIC and returns the active bit. - \param [in] IRQn Interrupt number. + \details Reads the active register in the NVIC and returns the active bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. \return 0 Interrupt status is not active. \return 1 Interrupt status is active. + \note IRQn must not be negative. */ -__STATIC_INLINE uint32_t NVIC_GetActive(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetActive(IRQn_Type IRQn) { - return ((uint32_t)(((NVIC->IABR[(((uint32_t)(int32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->IABR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** \brief Set Interrupt Priority - \details Sets the priority of an interrupt. - \note The priority cannot be set for every core interrupt. + \details Sets the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. \param [in] IRQn Interrupt number. \param [in] priority Priority to set. + \note The priority cannot be set for every processor exception. */ -__STATIC_INLINE void NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) +__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) { - if ((int32_t)(IRQn) < 0) + if ((int32_t)(IRQn) >= 0) { - SCB->SHPR[(((uint32_t)(int32_t)IRQn) & 0xFUL) - 4UL] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + NVIC->IP[((uint32_t)IRQn)] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); } else { - NVIC->IP[((uint32_t)(int32_t)IRQn)] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + SCB->SHPR[(((uint32_t)IRQn) & 0xFUL) - 4UL] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); } } /** \brief Get Interrupt Priority - \details Reads the priority of an interrupt. - The interrupt number can be positive to specify an external (device specific) interrupt, - or negative to specify an internal (core) interrupt. + \details Reads the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. \param [in] IRQn Interrupt number. \return Interrupt Priority. Value is aligned automatically to the implemented priority bits of the microcontroller. */ -__STATIC_INLINE uint32_t NVIC_GetPriority(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn) { - if ((int32_t)(IRQn) < 0) + + if ((int32_t)(IRQn) >= 0) { - return (((uint32_t)SCB->SHPR[(((uint32_t)(int32_t)IRQn) & 0xFUL) - 4UL] >> (8U - __NVIC_PRIO_BITS))); + return (((uint32_t)NVIC->IP[((uint32_t)IRQn)] >> (8U - __NVIC_PRIO_BITS))); } else { - return (((uint32_t)NVIC->IP[((uint32_t)(int32_t)IRQn)] >> (8U - __NVIC_PRIO_BITS))); + return (((uint32_t)SCB->SHPR[(((uint32_t)IRQn) & 0xFUL) - 4UL] >> (8U - __NVIC_PRIO_BITS))); } } @@ -1953,8 +2073,10 @@ __STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t P uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ uint32_t PreemptPriorityBits; uint32_t SubPriorityBits; + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + return ( ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) | ((SubPriority & (uint32_t)((1UL << (SubPriorityBits )) - 1UL))) @@ -1978,18 +2100,51 @@ __STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGr uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ uint32_t PreemptPriorityBits; uint32_t SubPriorityBits; + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL); *pSubPriority = (Priority ) & (uint32_t)((1UL << (SubPriorityBits )) - 1UL); } +/** + \brief Set Interrupt Vector + \details Sets an interrupt vector in SRAM based interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + VTOR must been relocated to SRAM before. + \param [in] IRQn Interrupt number + \param [in] vector Address of interrupt handler function + */ +__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector) +{ + uint32_t* vectors = (uint32_t*)SCB->VTOR; + vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector; +} + + +/** + \brief Get Interrupt Vector + \details Reads an interrupt vector from interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Address of interrupt handler function + */ +__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn) +{ + uint32_t* vectors = (uint32_t*)SCB->VTOR; + return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET]; +} + + /** \brief System Reset \details Initiates a system reset request to reset the MCU. */ -__STATIC_INLINE void NVIC_SystemReset(void) +__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void) { __DSB(); /* Ensure all outstanding memory accesses included buffered write are completed before reset */ @@ -2006,6 +2161,13 @@ __STATIC_INLINE void NVIC_SystemReset(void) /*@} end of CMSIS_Core_NVICFunctions */ +/* ########################## MPU functions #################################### */ + +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) + +#include "mpu_armv7.h" + +#endif /* ########################## FPU functions #################################### */ /** @@ -2026,19 +2188,20 @@ __STATIC_INLINE void NVIC_SystemReset(void) __STATIC_INLINE uint32_t SCB_GetFPUType(void) { uint32_t mvfr0; + mvfr0 = SCB->MVFR0; - if ((mvfr0 & 0x00000FF0UL) == 0x220UL) + if ((mvfr0 & (FPU_MVFR0_Single_precision_Msk | FPU_MVFR0_Double_precision_Msk)) == 0x220U) { - return 2UL; /* Double + Single precision FPU */ + return 2U; /* Double + Single precision FPU */ } - else if ((mvfr0 & 0x00000FF0UL) == 0x020UL) + else if ((mvfr0 & (FPU_MVFR0_Single_precision_Msk | FPU_MVFR0_Double_precision_Msk)) == 0x020U) { - return 1UL; /* Single precision FPU */ + return 1U; /* Single precision FPU */ } else { - return 0UL; /* No FPU */ + return 0U; /* No FPU */ } } @@ -2066,10 +2229,12 @@ __STATIC_INLINE uint32_t SCB_GetFPUType(void) */ __STATIC_INLINE void SCB_EnableICache (void) { -#if (__ICACHE_PRESENT == 1U) +#if defined (__ICACHE_PRESENT) && (__ICACHE_PRESENT == 1U) __DSB(); __ISB(); SCB->ICIALLU = 0UL; /* invalidate I-Cache */ + __DSB(); + __ISB(); SCB->CCR |= (uint32_t)SCB_CCR_IC_Msk; /* enable I-Cache */ __DSB(); __ISB(); @@ -2083,7 +2248,7 @@ __STATIC_INLINE void SCB_EnableICache (void) */ __STATIC_INLINE void SCB_DisableICache (void) { -#if (__ICACHE_PRESENT == 1U) +#if defined (__ICACHE_PRESENT) && (__ICACHE_PRESENT == 1U) __DSB(); __ISB(); SCB->CCR &= ~(uint32_t)SCB_CCR_IC_Msk; /* disable I-Cache */ @@ -2100,7 +2265,7 @@ __STATIC_INLINE void SCB_DisableICache (void) */ __STATIC_INLINE void SCB_InvalidateICache (void) { -#if (__ICACHE_PRESENT == 1U) +#if defined (__ICACHE_PRESENT) && (__ICACHE_PRESENT == 1U) __DSB(); __ISB(); SCB->ICIALLU = 0UL; @@ -2116,13 +2281,16 @@ __STATIC_INLINE void SCB_InvalidateICache (void) */ __STATIC_INLINE void SCB_EnableDCache (void) { -#if (__DCACHE_PRESENT == 1U) +#if defined (__DCACHE_PRESENT) && (__DCACHE_PRESENT == 1U) uint32_t ccsidr; uint32_t sets; uint32_t ways; - SCB->CSSELR = (0U << 1U) | 0U; /* Level 1 data cache */ + + SCB->CSSELR = 0U; /*(0U << 1U) | 0U;*/ /* Level 1 data cache */ __DSB(); + ccsidr = SCB->CCSIDR; + /* invalidate D-Cache */ sets = (uint32_t)(CCSIDR_SETS(ccsidr)); @@ -2138,12 +2306,14 @@ __STATIC_INLINE void SCB_EnableDCache (void) __schedule_barrier(); #endif } - while (ways--); + while (ways-- != 0U); } - while (sets--); + while (sets-- != 0U); __DSB(); + SCB->CCR |= (uint32_t)SCB_CCR_DC_Msk; /* enable D-Cache */ + __DSB(); __ISB(); #endif @@ -2156,14 +2326,19 @@ __STATIC_INLINE void SCB_EnableDCache (void) */ __STATIC_INLINE void SCB_DisableDCache (void) { -#if (__DCACHE_PRESENT == 1U) +#if defined (__DCACHE_PRESENT) && (__DCACHE_PRESENT == 1U) uint32_t ccsidr; uint32_t sets; uint32_t ways; - SCB->CSSELR = (0U << 1U) | 0U; /* Level 1 data cache */ + + SCB->CSSELR = 0U; /*(0U << 1U) | 0U;*/ /* Level 1 data cache */ __DSB(); - ccsidr = SCB->CCSIDR; + SCB->CCR &= ~(uint32_t)SCB_CCR_DC_Msk; /* disable D-Cache */ + __DSB(); + + ccsidr = SCB->CCSIDR; + /* clean & invalidate D-Cache */ sets = (uint32_t)(CCSIDR_SETS(ccsidr)); @@ -2179,9 +2354,9 @@ __STATIC_INLINE void SCB_DisableDCache (void) __schedule_barrier(); #endif } - while (ways--); + while (ways-- != 0U); } - while (sets--); + while (sets-- != 0U); __DSB(); __ISB(); @@ -2195,13 +2370,16 @@ __STATIC_INLINE void SCB_DisableDCache (void) */ __STATIC_INLINE void SCB_InvalidateDCache (void) { -#if (__DCACHE_PRESENT == 1U) +#if defined (__DCACHE_PRESENT) && (__DCACHE_PRESENT == 1U) uint32_t ccsidr; uint32_t sets; uint32_t ways; - SCB->CSSELR = (0U << 1U) | 0U; /* Level 1 data cache */ + + SCB->CSSELR = 0U; /*(0U << 1U) | 0U;*/ /* Level 1 data cache */ __DSB(); + ccsidr = SCB->CCSIDR; + /* invalidate D-Cache */ sets = (uint32_t)(CCSIDR_SETS(ccsidr)); @@ -2217,9 +2395,9 @@ __STATIC_INLINE void SCB_InvalidateDCache (void) __schedule_barrier(); #endif } - while (ways--); + while (ways-- != 0U); } - while (sets--); + while (sets-- != 0U); __DSB(); __ISB(); @@ -2233,13 +2411,16 @@ __STATIC_INLINE void SCB_InvalidateDCache (void) */ __STATIC_INLINE void SCB_CleanDCache (void) { -#if (__DCACHE_PRESENT == 1U) +#if defined (__DCACHE_PRESENT) && (__DCACHE_PRESENT == 1U) uint32_t ccsidr; uint32_t sets; uint32_t ways; - SCB->CSSELR = (0U << 1U) | 0U; /* Level 1 data cache */ + + SCB->CSSELR = 0U; /*(0U << 1U) | 0U;*/ /* Level 1 data cache */ __DSB(); + ccsidr = SCB->CCSIDR; + /* clean D-Cache */ sets = (uint32_t)(CCSIDR_SETS(ccsidr)); @@ -2255,9 +2436,9 @@ __STATIC_INLINE void SCB_CleanDCache (void) __schedule_barrier(); #endif } - while (ways--); + while (ways-- != 0U); } - while (sets--); + while (sets-- != 0U); __DSB(); __ISB(); @@ -2271,13 +2452,16 @@ __STATIC_INLINE void SCB_CleanDCache (void) */ __STATIC_INLINE void SCB_CleanInvalidateDCache (void) { -#if (__DCACHE_PRESENT == 1U) +#if defined (__DCACHE_PRESENT) && (__DCACHE_PRESENT == 1U) uint32_t ccsidr; uint32_t sets; uint32_t ways; - SCB->CSSELR = (0U << 1U) | 0U; /* Level 1 data cache */ + + SCB->CSSELR = 0U; /*(0U << 1U) | 0U;*/ /* Level 1 data cache */ __DSB(); + ccsidr = SCB->CCSIDR; + /* clean & invalidate D-Cache */ sets = (uint32_t)(CCSIDR_SETS(ccsidr)); @@ -2293,9 +2477,9 @@ __STATIC_INLINE void SCB_CleanInvalidateDCache (void) __schedule_barrier(); #endif } - while (ways--); + while (ways-- != 0U); } - while (sets--); + while (sets-- != 0U); __DSB(); __ISB(); @@ -2311,17 +2495,18 @@ __STATIC_INLINE void SCB_CleanInvalidateDCache (void) */ __STATIC_INLINE void SCB_InvalidateDCache_by_Addr (uint32_t* addr, int32_t dsize) { -#if (__DCACHE_PRESENT == 1U) +#if defined (__DCACHE_PRESENT) && (__DCACHE_PRESENT == 1U) int32_t op_size = dsize; uint32_t op_addr = (uint32_t)addr; - int32_t linesize = 32U; /* in Cortex-M7 size of cache line is fixed to 8 words (32 bytes) */ + int32_t linesize = 32; /* in Cortex-M7 size of cache line is fixed to 8 words (32 bytes) */ + __DSB(); while (op_size > 0) { SCB->DCIMVAC = op_addr; - op_addr += linesize; - op_size -= linesize; + op_addr += (uint32_t)linesize; + op_size -= linesize; } __DSB(); @@ -2338,17 +2523,18 @@ __STATIC_INLINE void SCB_InvalidateDCache_by_Addr (uint32_t* addr, int32_t dsize */ __STATIC_INLINE void SCB_CleanDCache_by_Addr (uint32_t* addr, int32_t dsize) { -#if (__DCACHE_PRESENT == 1) +#if defined (__DCACHE_PRESENT) && (__DCACHE_PRESENT == 1U) int32_t op_size = dsize; uint32_t op_addr = (uint32_t) addr; - int32_t linesize = 32U; /* in Cortex-M7 size of cache line is fixed to 8 words (32 bytes) */ + int32_t linesize = 32; /* in Cortex-M7 size of cache line is fixed to 8 words (32 bytes) */ + __DSB(); while (op_size > 0) { SCB->DCCMVAC = op_addr; - op_addr += linesize; - op_size -= linesize; + op_addr += (uint32_t)linesize; + op_size -= linesize; } __DSB(); @@ -2365,17 +2551,18 @@ __STATIC_INLINE void SCB_CleanDCache_by_Addr (uint32_t* addr, int32_t dsize) */ __STATIC_INLINE void SCB_CleanInvalidateDCache_by_Addr (uint32_t* addr, int32_t dsize) { -#if (__DCACHE_PRESENT == 1U) +#if defined (__DCACHE_PRESENT) && (__DCACHE_PRESENT == 1U) int32_t op_size = dsize; uint32_t op_addr = (uint32_t) addr; - int32_t linesize = 32U; /* in Cortex-M7 size of cache line is fixed to 8 words (32 bytes) */ + int32_t linesize = 32; /* in Cortex-M7 size of cache line is fixed to 8 words (32 bytes) */ + __DSB(); while (op_size > 0) { SCB->DCCIMVAC = op_addr; - op_addr += linesize; - op_size -= linesize; + op_addr += (uint32_t)linesize; + op_size -= linesize; } __DSB(); @@ -2396,7 +2583,7 @@ __STATIC_INLINE void SCB_CleanInvalidateDCache_by_Addr (uint32_t* addr, int32_t @{ */ -#if (__Vendor_SysTickConfig == 0U) +#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U) /** \brief System Tick Configuration @@ -2439,8 +2626,8 @@ __STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks) @{ */ -extern volatile int32_t ITM_RxBuffer; /*!< External variable to receive characters. */ -#define ITM_RXBUFFER_EMPTY 0x5AA55AA5U /*!< Value identifying \ref ITM_RxBuffer is ready for next character. */ +extern volatile int32_t ITM_RxBuffer; /*!< External variable to receive characters. */ +#define ITM_RXBUFFER_EMPTY ((int32_t)0x5AA55AA5U) /*!< Value identifying \ref ITM_RxBuffer is ready for next character. */ /** @@ -2496,6 +2683,7 @@ __STATIC_INLINE int32_t ITM_ReceiveChar (void) */ __STATIC_INLINE int32_t ITM_CheckChar (void) { + if (ITM_RxBuffer == ITM_RXBUFFER_EMPTY) { return (0); /* no character available */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/core_cmFunc.h b/EpsilonLights/Drivers/CMSIS/Include/core_cmFunc.h deleted file mode 100644 index 95b27b84..00000000 --- a/EpsilonLights/Drivers/CMSIS/Include/core_cmFunc.h +++ /dev/null @@ -1,87 +0,0 @@ -/**************************************************************************//** - * @file core_cmFunc.h - * @brief CMSIS Cortex-M Core Function Access Header File - * @version V4.30 - * @date 20. October 2015 - ******************************************************************************/ -/* Copyright (c) 2009 - 2015 ARM LIMITED - - All rights reserved. - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - - Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - - Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - Neither the name of ARM nor the names of its contributors may be used - to endorse or promote products derived from this software without - specific prior written permission. - * - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE - LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR - CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF - SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS - INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN - CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) - ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE - POSSIBILITY OF SUCH DAMAGE. - ---------------------------------------------------------------------------*/ - - -#if defined ( __ICCARM__ ) -#pragma system_include /* treat file as system include file for MISRA check */ -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) -#pragma clang system_header /* treat file as system include file */ -#endif - -#ifndef __CORE_CMFUNC_H -#define __CORE_CMFUNC_H - - -/* ########################### Core Function Access ########################### */ -/** \ingroup CMSIS_Core_FunctionInterface - \defgroup CMSIS_Core_RegAccFunctions CMSIS Core Register Access Functions - @{ -*/ - -/*------------------ RealView Compiler -----------------*/ -#if defined ( __CC_ARM ) -#include "cmsis_armcc.h" - -/*------------------ ARM Compiler V6 -------------------*/ -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) -#include "cmsis_armcc_V6.h" - -/*------------------ GNU Compiler ----------------------*/ -#elif defined ( __GNUC__ ) -#include "cmsis_gcc.h" - -/*------------------ ICC Compiler ----------------------*/ -#elif defined ( __ICCARM__ ) -#include - -/*------------------ TI CCS Compiler -------------------*/ -#elif defined ( __TMS470__ ) -#include - -/*------------------ TASKING Compiler ------------------*/ -#elif defined ( __TASKING__ ) -/* - * The CMSIS functions have been implemented as intrinsics in the compiler. - * Please use "carm -?i" to get an up to date list of all intrinsics, - * Including the CMSIS ones. - */ - -/*------------------ COSMIC Compiler -------------------*/ -#elif defined ( __CSMC__ ) -#include - -#endif - -/*@} end of CMSIS_Core_RegAccFunctions */ - -#endif /* __CORE_CMFUNC_H */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/core_cmInstr.h b/EpsilonLights/Drivers/CMSIS/Include/core_cmInstr.h deleted file mode 100644 index c1ab6376..00000000 --- a/EpsilonLights/Drivers/CMSIS/Include/core_cmInstr.h +++ /dev/null @@ -1,87 +0,0 @@ -/**************************************************************************//** - * @file core_cmInstr.h - * @brief CMSIS Cortex-M Core Instruction Access Header File - * @version V4.30 - * @date 20. October 2015 - ******************************************************************************/ -/* Copyright (c) 2009 - 2015 ARM LIMITED - - All rights reserved. - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - - Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - - Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - Neither the name of ARM nor the names of its contributors may be used - to endorse or promote products derived from this software without - specific prior written permission. - * - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE - LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR - CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF - SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS - INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN - CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) - ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE - POSSIBILITY OF SUCH DAMAGE. - ---------------------------------------------------------------------------*/ - - -#if defined ( __ICCARM__ ) -#pragma system_include /* treat file as system include file for MISRA check */ -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) -#pragma clang system_header /* treat file as system include file */ -#endif - -#ifndef __CORE_CMINSTR_H -#define __CORE_CMINSTR_H - - -/* ########################## Core Instruction Access ######################### */ -/** \defgroup CMSIS_Core_InstructionInterface CMSIS Core Instruction Interface - Access to dedicated instructions - @{ -*/ - -/*------------------ RealView Compiler -----------------*/ -#if defined ( __CC_ARM ) -#include "cmsis_armcc.h" - -/*------------------ ARM Compiler V6 -------------------*/ -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) -#include "cmsis_armcc_V6.h" - -/*------------------ GNU Compiler ----------------------*/ -#elif defined ( __GNUC__ ) -#include "cmsis_gcc.h" - -/*------------------ ICC Compiler ----------------------*/ -#elif defined ( __ICCARM__ ) -#include - -/*------------------ TI CCS Compiler -------------------*/ -#elif defined ( __TMS470__ ) -#include - -/*------------------ TASKING Compiler ------------------*/ -#elif defined ( __TASKING__ ) -/* - * The CMSIS functions have been implemented as intrinsics in the compiler. - * Please use "carm -?i" to get an up to date list of all intrinsics, - * Including the CMSIS ones. - */ - -/*------------------ COSMIC Compiler -------------------*/ -#elif defined ( __CSMC__ ) -#include - -#endif - -/*@}*/ /* end of group CMSIS_Core_InstructionInterface */ - -#endif /* __CORE_CMINSTR_H */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/core_cmSimd.h b/EpsilonLights/Drivers/CMSIS/Include/core_cmSimd.h deleted file mode 100644 index af5337d6..00000000 --- a/EpsilonLights/Drivers/CMSIS/Include/core_cmSimd.h +++ /dev/null @@ -1,96 +0,0 @@ -/**************************************************************************//** - * @file core_cmSimd.h - * @brief CMSIS Cortex-M SIMD Header File - * @version V4.30 - * @date 20. October 2015 - ******************************************************************************/ -/* Copyright (c) 2009 - 2015 ARM LIMITED - - All rights reserved. - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - - Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - - Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - Neither the name of ARM nor the names of its contributors may be used - to endorse or promote products derived from this software without - specific prior written permission. - * - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE - LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR - CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF - SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS - INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN - CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) - ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE - POSSIBILITY OF SUCH DAMAGE. - ---------------------------------------------------------------------------*/ - - -#if defined ( __ICCARM__ ) -#pragma system_include /* treat file as system include file for MISRA check */ -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) -#pragma clang system_header /* treat file as system include file */ -#endif - -#ifndef __CORE_CMSIMD_H -#define __CORE_CMSIMD_H - -#ifdef __cplusplus -extern "C" { -#endif - - -/* ################### Compiler specific Intrinsics ########################### */ -/** \defgroup CMSIS_SIMD_intrinsics CMSIS SIMD Intrinsics - Access to dedicated SIMD instructions - @{ -*/ - -/*------------------ RealView Compiler -----------------*/ -#if defined ( __CC_ARM ) -#include "cmsis_armcc.h" - -/*------------------ ARM Compiler V6 -------------------*/ -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) -#include "cmsis_armcc_V6.h" - -/*------------------ GNU Compiler ----------------------*/ -#elif defined ( __GNUC__ ) -#include "cmsis_gcc.h" - -/*------------------ ICC Compiler ----------------------*/ -#elif defined ( __ICCARM__ ) -#include - -/*------------------ TI CCS Compiler -------------------*/ -#elif defined ( __TMS470__ ) -#include - -/*------------------ TASKING Compiler ------------------*/ -#elif defined ( __TASKING__ ) -/* - * The CMSIS functions have been implemented as intrinsics in the compiler. - * Please use "carm -?i" to get an up to date list of all intrinsics, - * Including the CMSIS ones. - */ - -/*------------------ COSMIC Compiler -------------------*/ -#elif defined ( __CSMC__ ) -#include - -#endif - -/*@} end of group CMSIS_SIMD_intrinsics */ - - -#ifdef __cplusplus -} -#endif - -#endif /* __CORE_CMSIMD_H */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/core_sc000.h b/EpsilonLights/Drivers/CMSIS/Include/core_sc000.h index 7a05e1a2..0ebc7f10 100644 --- a/EpsilonLights/Drivers/CMSIS/Include/core_sc000.h +++ b/EpsilonLights/Drivers/CMSIS/Include/core_sc000.h @@ -1,40 +1,30 @@ /**************************************************************************//** * @file core_sc000.h * @brief CMSIS SC000 Core Peripheral Access Layer Header File - * @version V4.30 - * @date 20. October 2015 + * @version V5.0.5 + * @date 28. May 2018 ******************************************************************************/ -/* Copyright (c) 2009 - 2015 ARM LIMITED - - All rights reserved. - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - - Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - - Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - Neither the name of ARM nor the names of its contributors may be used - to endorse or promote products derived from this software without - specific prior written permission. - * - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE - LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR - CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF - SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS - INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN - CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) - ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE - POSSIBILITY OF SUCH DAMAGE. - ---------------------------------------------------------------------------*/ - +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ #if defined ( __ICCARM__ ) #pragma system_include /* treat file as system include file for MISRA check */ -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#elif defined (__clang__) #pragma clang system_header /* treat file as system include file */ #endif @@ -70,53 +60,15 @@ extern "C" { @{ */ +#include "cmsis_version.h" + /* CMSIS SC000 definitions */ -#define __SC000_CMSIS_VERSION_MAIN (0x04U) /*!< [31:16] CMSIS HAL main version */ -#define __SC000_CMSIS_VERSION_SUB (0x1EU) /*!< [15:0] CMSIS HAL sub version */ +#define __SC000_CMSIS_VERSION_MAIN (__CM_CMSIS_VERSION_MAIN) /*!< \deprecated [31:16] CMSIS HAL main version */ +#define __SC000_CMSIS_VERSION_SUB (__CM_CMSIS_VERSION_SUB) /*!< \deprecated [15:0] CMSIS HAL sub version */ #define __SC000_CMSIS_VERSION ((__SC000_CMSIS_VERSION_MAIN << 16U) | \ - __SC000_CMSIS_VERSION_SUB ) /*!< CMSIS HAL version number */ - -#define __CORTEX_SC (000U) /*!< Cortex secure core */ - - -#if defined ( __CC_ARM ) -#define __ASM __asm /*!< asm keyword for ARM Compiler */ -#define __INLINE __inline /*!< inline keyword for ARM Compiler */ -#define __STATIC_INLINE static __inline - -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) -#define __ASM __asm /*!< asm keyword for ARM Compiler */ -#define __INLINE __inline /*!< inline keyword for ARM Compiler */ -#define __STATIC_INLINE static __inline - -#elif defined ( __GNUC__ ) -#define __ASM __asm /*!< asm keyword for GNU Compiler */ -#define __INLINE inline /*!< inline keyword for GNU Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __ICCARM__ ) -#define __ASM __asm /*!< asm keyword for IAR Compiler */ -#define __INLINE inline /*!< inline keyword for IAR Compiler. Only available in High optimization mode! */ -#define __STATIC_INLINE static inline + __SC000_CMSIS_VERSION_SUB ) /*!< \deprecated CMSIS HAL version number */ -#elif defined ( __TMS470__ ) -#define __ASM __asm /*!< asm keyword for TI CCS Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __TASKING__ ) -#define __ASM __asm /*!< asm keyword for TASKING Compiler */ -#define __INLINE inline /*!< inline keyword for TASKING Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __CSMC__ ) -#define __packed -#define __ASM _asm /*!< asm keyword for COSMIC Compiler */ -#define __INLINE inline /*!< inline keyword for COSMIC Compiler. Use -pc99 on compile line */ -#define __STATIC_INLINE static inline - -#else -#error Unknown compiler -#endif +#define __CORTEX_SC (000U) /*!< Cortex secure core */ /** __FPU_USED indicates whether an FPU is used or not. This core does not support an FPU at all @@ -128,7 +80,7 @@ extern "C" { #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) #if defined __ARM_PCS_VFP #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif @@ -143,7 +95,7 @@ extern "C" { #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif -#elif defined ( __TMS470__ ) +#elif defined ( __TI_ARM__ ) #if defined __TI_VFP_SUPPORT__ #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif @@ -160,8 +112,8 @@ extern "C" { #endif -#include "core_cmInstr.h" /* Core Instruction Access */ -#include "core_cmFunc.h" /* Core Function Access */ +#include "cmsis_compiler.h" /* CMSIS compiler specific defines */ + #ifdef __cplusplus } @@ -569,7 +521,7 @@ typedef struct /*@} end of group CMSIS_SysTick */ -#if (__MPU_PRESENT == 1U) +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) /** \ingroup CMSIS_core_register \defgroup CMSIS_MPU Memory Protection Unit (MPU) @@ -678,18 +630,18 @@ typedef struct /** \brief Mask and shift a bit field value for use in a register bit range. \param[in] field Name of the register bit field. - \param[in] value Value of the bit field. + \param[in] value Value of the bit field. This parameter is interpreted as an uint32_t type. \return Masked and shifted value. */ -#define _VAL2FLD(field, value) ((value << field ## _Pos) & field ## _Msk) +#define _VAL2FLD(field, value) (((uint32_t)(value) << field ## _Pos) & field ## _Msk) /** \brief Mask and shift a register value to extract a bit filed value. \param[in] field Name of the register bit field. - \param[in] value Value of register. + \param[in] value Value of register. This parameter is interpreted as an uint32_t type. \return Masked and shifted bit field value. */ -#define _FLD2VAL(field, value) ((value & field ## _Msk) >> field ## _Pos) +#define _FLD2VAL(field, value) (((uint32_t)(value) & field ## _Msk) >> field ## _Pos) /*@} end of group CMSIS_core_bitfield */ @@ -701,7 +653,7 @@ typedef struct @{ */ -/* Memory mapping of SC000 Hardware */ +/* Memory mapping of Core Hardware */ #define SCS_BASE (0xE000E000UL) /*!< System Control Space Base Address */ #define SysTick_BASE (SCS_BASE + 0x0010UL) /*!< SysTick Base Address */ #define NVIC_BASE (SCS_BASE + 0x0100UL) /*!< NVIC Base Address */ @@ -712,7 +664,7 @@ typedef struct #define SysTick ((SysTick_Type *) SysTick_BASE ) /*!< SysTick configuration struct */ #define NVIC ((NVIC_Type *) NVIC_BASE ) /*!< NVIC configuration struct */ -#if (__MPU_PRESENT == 1U) +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) #define MPU_BASE (SCS_BASE + 0x0D90UL) /*!< Memory Protection Unit */ #define MPU ((MPU_Type *) MPU_BASE ) /*!< Memory Protection Unit */ #endif @@ -742,7 +694,46 @@ typedef struct @{ */ -/* Interrupt Priorities are WORD accessible only under ARMv6M */ +#ifdef CMSIS_NVIC_VIRTUAL +#ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE +#define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h" +#endif +#include CMSIS_NVIC_VIRTUAL_HEADER_FILE +#else +/*#define NVIC_SetPriorityGrouping __NVIC_SetPriorityGrouping not available for SC000 */ +/*#define NVIC_GetPriorityGrouping __NVIC_GetPriorityGrouping not available for SC000 */ +#define NVIC_EnableIRQ __NVIC_EnableIRQ +#define NVIC_GetEnableIRQ __NVIC_GetEnableIRQ +#define NVIC_DisableIRQ __NVIC_DisableIRQ +#define NVIC_GetPendingIRQ __NVIC_GetPendingIRQ +#define NVIC_SetPendingIRQ __NVIC_SetPendingIRQ +#define NVIC_ClearPendingIRQ __NVIC_ClearPendingIRQ +/*#define NVIC_GetActive __NVIC_GetActive not available for SC000 */ +#define NVIC_SetPriority __NVIC_SetPriority +#define NVIC_GetPriority __NVIC_GetPriority +#define NVIC_SystemReset __NVIC_SystemReset +#endif /* CMSIS_NVIC_VIRTUAL */ + +#ifdef CMSIS_VECTAB_VIRTUAL +#ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h" +#endif +#include CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetVector __NVIC_SetVector +#define NVIC_GetVector __NVIC_GetVector +#endif /* (CMSIS_VECTAB_VIRTUAL) */ + +#define NVIC_USER_IRQ_OFFSET 16 + + +/* The following EXC_RETURN values are saved the LR on exception entry */ +#define EXC_RETURN_HANDLER (0xFFFFFFF1UL) /* return to Handler mode, uses MSP after return */ +#define EXC_RETURN_THREAD_MSP (0xFFFFFFF9UL) /* return to Thread mode, uses MSP after return */ +#define EXC_RETURN_THREAD_PSP (0xFFFFFFFDUL) /* return to Thread mode, uses PSP after return */ + + +/* Interrupt Priorities are WORD accessible only under Armv6-M */ /* The following MACROS handle generation of the register offset and byte masks */ #define _BIT_SHIFT(IRQn) ( ((((uint32_t)(int32_t)(IRQn)) ) & 0x03UL) * 8UL) #define _SHP_IDX(IRQn) ( (((((uint32_t)(int32_t)(IRQn)) & 0x0FUL)-8UL) >> 2UL) ) @@ -750,79 +741,128 @@ typedef struct /** - \brief Enable External Interrupt - \details Enables a device-specific interrupt in the NVIC interrupt controller. - \param [in] IRQn External interrupt number. Value cannot be negative. + \brief Enable Interrupt + \details Enables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Interrupt Enable status + \details Returns a device specific interrupt enable status from the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_EnableIRQ(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn) { - NVIC->ISER[0U] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISER[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** - \brief Disable External Interrupt - \details Disables a device-specific interrupt in the NVIC interrupt controller. - \param [in] IRQn External interrupt number. Value cannot be negative. + \brief Disable Interrupt + \details Disables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_DisableIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn) { - NVIC->ICER[0U] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + __DSB(); + __ISB(); + } } /** \brief Get Pending Interrupt - \details Reads the pending register in the NVIC and returns the pending bit for the specified interrupt. - \param [in] IRQn Interrupt number. + \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. \return 0 Interrupt status is not pending. \return 1 Interrupt status is pending. + \note IRQn must not be negative. */ -__STATIC_INLINE uint32_t NVIC_GetPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn) { - return ((uint32_t)(((NVIC->ISPR[0U] & (1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISPR[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** \brief Set Pending Interrupt - \details Sets the pending bit of an external interrupt. - \param [in] IRQn Interrupt number. Value cannot be negative. + \details Sets the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_SetPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn) { - NVIC->ISPR[0U] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** \brief Clear Pending Interrupt - \details Clears the pending bit of an external interrupt. - \param [in] IRQn External interrupt number. Value cannot be negative. + \details Clears the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_ClearPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn) { - NVIC->ICPR[0U] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** \brief Set Interrupt Priority - \details Sets the priority of an interrupt. - \note The priority cannot be set for every core interrupt. + \details Sets the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. \param [in] IRQn Interrupt number. \param [in] priority Priority to set. + \note The priority cannot be set for every processor exception. */ -__STATIC_INLINE void NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) +__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) { - if ((int32_t)(IRQn) < 0) + if ((int32_t)(IRQn) >= 0) { - SCB->SHP[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHP[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + NVIC->IP[_IP_IDX(IRQn)] = ((uint32_t)(NVIC->IP[_IP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); } else { - NVIC->IP[_IP_IDX(IRQn)] = ((uint32_t)(NVIC->IP[_IP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | + SCB->SHP[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHP[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) | (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn))); } } @@ -830,31 +870,63 @@ __STATIC_INLINE void NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) /** \brief Get Interrupt Priority - \details Reads the priority of an interrupt. - The interrupt number can be positive to specify an external (device specific) interrupt, - or negative to specify an internal (core) interrupt. + \details Reads the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. \param [in] IRQn Interrupt number. \return Interrupt Priority. Value is aligned automatically to the implemented priority bits of the microcontroller. */ -__STATIC_INLINE uint32_t NVIC_GetPriority(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn) { - if ((int32_t)(IRQn) < 0) + + if ((int32_t)(IRQn) >= 0) { - return ((uint32_t)(((SCB->SHP[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + return ((uint32_t)(((NVIC->IP[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); } else { - return ((uint32_t)(((NVIC->IP[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); + return ((uint32_t)(((SCB->SHP[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS))); } } +/** + \brief Set Interrupt Vector + \details Sets an interrupt vector in SRAM based interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + VTOR must been relocated to SRAM before. + \param [in] IRQn Interrupt number + \param [in] vector Address of interrupt handler function + */ +__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector) +{ + uint32_t* vectors = (uint32_t*)SCB->VTOR; + vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector; +} + + +/** + \brief Get Interrupt Vector + \details Reads an interrupt vector from interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Address of interrupt handler function + */ +__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn) +{ + uint32_t* vectors = (uint32_t*)SCB->VTOR; + return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET]; +} + + /** \brief System Reset \details Initiates a system reset request to reset the MCU. */ -__STATIC_INLINE void NVIC_SystemReset(void) +__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void) { __DSB(); /* Ensure all outstanding memory accesses included buffered write are completed before reset */ @@ -871,6 +943,31 @@ __STATIC_INLINE void NVIC_SystemReset(void) /*@} end of CMSIS_Core_NVICFunctions */ +/* ########################## FPU functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_FpuFunctions FPU Functions + \brief Function that provides FPU type. + @{ + */ + +/** + \brief get FPU type + \details returns the FPU type + \returns + - \b 0: No FPU + - \b 1: Single precision FPU + - \b 2: Double + Single precision FPU + */ +__STATIC_INLINE uint32_t SCB_GetFPUType(void) +{ + return 0U; /* No FPU */ +} + + +/*@} end of CMSIS_Core_FpuFunctions */ + + /* ################################## SysTick function ############################################ */ /** @@ -880,7 +977,7 @@ __STATIC_INLINE void NVIC_SystemReset(void) @{ */ -#if (__Vendor_SysTickConfig == 0U) +#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U) /** \brief System Tick Configuration diff --git a/EpsilonLights/Drivers/CMSIS/Include/core_sc300.h b/EpsilonLights/Drivers/CMSIS/Include/core_sc300.h index 6310a702..b9638b8a 100644 --- a/EpsilonLights/Drivers/CMSIS/Include/core_sc300.h +++ b/EpsilonLights/Drivers/CMSIS/Include/core_sc300.h @@ -1,40 +1,30 @@ /**************************************************************************//** * @file core_sc300.h * @brief CMSIS SC300 Core Peripheral Access Layer Header File - * @version V4.30 - * @date 20. October 2015 + * @version V5.0.6 + * @date 04. June 2018 ******************************************************************************/ -/* Copyright (c) 2009 - 2015 ARM LIMITED - - All rights reserved. - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - - Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - - Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - Neither the name of ARM nor the names of its contributors may be used - to endorse or promote products derived from this software without - specific prior written permission. - * - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE - LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR - CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF - SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS - INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN - CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) - ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE - POSSIBILITY OF SUCH DAMAGE. - ---------------------------------------------------------------------------*/ - +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ #if defined ( __ICCARM__ ) #pragma system_include /* treat file as system include file for MISRA check */ -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#elif defined (__clang__) #pragma clang system_header /* treat file as system include file */ #endif @@ -70,53 +60,15 @@ extern "C" { @{ */ +#include "cmsis_version.h" + /* CMSIS SC300 definitions */ -#define __SC300_CMSIS_VERSION_MAIN (0x04U) /*!< [31:16] CMSIS HAL main version */ -#define __SC300_CMSIS_VERSION_SUB (0x1EU) /*!< [15:0] CMSIS HAL sub version */ +#define __SC300_CMSIS_VERSION_MAIN (__CM_CMSIS_VERSION_MAIN) /*!< \deprecated [31:16] CMSIS HAL main version */ +#define __SC300_CMSIS_VERSION_SUB (__CM_CMSIS_VERSION_SUB) /*!< \deprecated [15:0] CMSIS HAL sub version */ #define __SC300_CMSIS_VERSION ((__SC300_CMSIS_VERSION_MAIN << 16U) | \ - __SC300_CMSIS_VERSION_SUB ) /*!< CMSIS HAL version number */ - -#define __CORTEX_SC (300U) /*!< Cortex secure core */ + __SC300_CMSIS_VERSION_SUB ) /*!< \deprecated CMSIS HAL version number */ - -#if defined ( __CC_ARM ) -#define __ASM __asm /*!< asm keyword for ARM Compiler */ -#define __INLINE __inline /*!< inline keyword for ARM Compiler */ -#define __STATIC_INLINE static __inline - -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) -#define __ASM __asm /*!< asm keyword for ARM Compiler */ -#define __INLINE __inline /*!< inline keyword for ARM Compiler */ -#define __STATIC_INLINE static __inline - -#elif defined ( __GNUC__ ) -#define __ASM __asm /*!< asm keyword for GNU Compiler */ -#define __INLINE inline /*!< inline keyword for GNU Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __ICCARM__ ) -#define __ASM __asm /*!< asm keyword for IAR Compiler */ -#define __INLINE inline /*!< inline keyword for IAR Compiler. Only available in High optimization mode! */ -#define __STATIC_INLINE static inline - -#elif defined ( __TMS470__ ) -#define __ASM __asm /*!< asm keyword for TI CCS Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __TASKING__ ) -#define __ASM __asm /*!< asm keyword for TASKING Compiler */ -#define __INLINE inline /*!< inline keyword for TASKING Compiler */ -#define __STATIC_INLINE static inline - -#elif defined ( __CSMC__ ) -#define __packed -#define __ASM _asm /*!< asm keyword for COSMIC Compiler */ -#define __INLINE inline /*!< inline keyword for COSMIC Compiler. Use -pc99 on compile line */ -#define __STATIC_INLINE static inline - -#else -#error Unknown compiler -#endif +#define __CORTEX_SC (300U) /*!< Cortex secure core */ /** __FPU_USED indicates whether an FPU is used or not. This core does not support an FPU at all @@ -128,7 +80,7 @@ extern "C" { #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif -#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) +#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) #if defined __ARM_PCS_VFP #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif @@ -143,7 +95,7 @@ extern "C" { #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif -#elif defined ( __TMS470__ ) +#elif defined ( __TI_ARM__ ) #if defined __TI_VFP_SUPPORT__ #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)" #endif @@ -160,8 +112,8 @@ extern "C" { #endif -#include "core_cmInstr.h" /* Core Instruction Access */ -#include "core_cmFunc.h" /* Core Function Access */ +#include "cmsis_compiler.h" /* CMSIS compiler specific defines */ + #ifdef __cplusplus } @@ -191,7 +143,7 @@ extern "C" { #endif #ifndef __NVIC_PRIO_BITS -#define __NVIC_PRIO_BITS 4U +#define __NVIC_PRIO_BITS 3U #warning "__NVIC_PRIO_BITS not defined in device header file; using default!" #endif @@ -308,9 +260,11 @@ typedef union struct { uint32_t ISR: 9; /*!< bit: 0.. 8 Exception number */ - uint32_t _reserved0: 15; /*!< bit: 9..23 Reserved */ - uint32_t T: 1; /*!< bit: 24 Thumb bit (read 0) */ - uint32_t IT: 2; /*!< bit: 25..26 saved IT state (read 0) */ + uint32_t _reserved0: 1; /*!< bit: 9 Reserved */ + uint32_t ICI_IT_1: 6; /*!< bit: 10..15 ICI/IT part 1 */ + uint32_t _reserved1: 8; /*!< bit: 16..23 Reserved */ + uint32_t T: 1; /*!< bit: 24 Thumb bit */ + uint32_t ICI_IT_2: 2; /*!< bit: 25..26 ICI/IT part 2 */ uint32_t Q: 1; /*!< bit: 27 Saturation condition flag */ uint32_t V: 1; /*!< bit: 28 Overflow condition code flag */ uint32_t C: 1; /*!< bit: 29 Carry condition code flag */ @@ -336,12 +290,15 @@ typedef union #define xPSR_Q_Pos 27U /*!< xPSR: Q Position */ #define xPSR_Q_Msk (1UL << xPSR_Q_Pos) /*!< xPSR: Q Mask */ -#define xPSR_IT_Pos 25U /*!< xPSR: IT Position */ -#define xPSR_IT_Msk (3UL << xPSR_IT_Pos) /*!< xPSR: IT Mask */ +#define xPSR_ICI_IT_2_Pos 25U /*!< xPSR: ICI/IT part 2 Position */ +#define xPSR_ICI_IT_2_Msk (3UL << xPSR_ICI_IT_2_Pos) /*!< xPSR: ICI/IT part 2 Mask */ #define xPSR_T_Pos 24U /*!< xPSR: T Position */ #define xPSR_T_Msk (1UL << xPSR_T_Pos) /*!< xPSR: T Mask */ +#define xPSR_ICI_IT_1_Pos 10U /*!< xPSR: ICI/IT part 1 Position */ +#define xPSR_ICI_IT_1_Msk (0x3FUL << xPSR_ICI_IT_1_Pos) /*!< xPSR: ICI/IT part 1 Mask */ + #define xPSR_ISR_Pos 0U /*!< xPSR: ISR Position */ #define xPSR_ISR_Msk (0x1FFUL /*<< xPSR_ISR_Pos*/) /*!< xPSR: ISR Mask */ @@ -599,6 +556,60 @@ typedef struct #define SCB_CFSR_MEMFAULTSR_Pos 0U /*!< SCB CFSR: Memory Manage Fault Status Register Position */ #define SCB_CFSR_MEMFAULTSR_Msk (0xFFUL /*<< SCB_CFSR_MEMFAULTSR_Pos*/) /*!< SCB CFSR: Memory Manage Fault Status Register Mask */ +/* MemManage Fault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_MMARVALID_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 7U) /*!< SCB CFSR (MMFSR): MMARVALID Position */ +#define SCB_CFSR_MMARVALID_Msk (1UL << SCB_CFSR_MMARVALID_Pos) /*!< SCB CFSR (MMFSR): MMARVALID Mask */ + +#define SCB_CFSR_MSTKERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 4U) /*!< SCB CFSR (MMFSR): MSTKERR Position */ +#define SCB_CFSR_MSTKERR_Msk (1UL << SCB_CFSR_MSTKERR_Pos) /*!< SCB CFSR (MMFSR): MSTKERR Mask */ + +#define SCB_CFSR_MUNSTKERR_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 3U) /*!< SCB CFSR (MMFSR): MUNSTKERR Position */ +#define SCB_CFSR_MUNSTKERR_Msk (1UL << SCB_CFSR_MUNSTKERR_Pos) /*!< SCB CFSR (MMFSR): MUNSTKERR Mask */ + +#define SCB_CFSR_DACCVIOL_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 1U) /*!< SCB CFSR (MMFSR): DACCVIOL Position */ +#define SCB_CFSR_DACCVIOL_Msk (1UL << SCB_CFSR_DACCVIOL_Pos) /*!< SCB CFSR (MMFSR): DACCVIOL Mask */ + +#define SCB_CFSR_IACCVIOL_Pos (SCB_SHCSR_MEMFAULTACT_Pos + 0U) /*!< SCB CFSR (MMFSR): IACCVIOL Position */ +#define SCB_CFSR_IACCVIOL_Msk (1UL /*<< SCB_CFSR_IACCVIOL_Pos*/) /*!< SCB CFSR (MMFSR): IACCVIOL Mask */ + +/* BusFault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_BFARVALID_Pos (SCB_CFSR_BUSFAULTSR_Pos + 7U) /*!< SCB CFSR (BFSR): BFARVALID Position */ +#define SCB_CFSR_BFARVALID_Msk (1UL << SCB_CFSR_BFARVALID_Pos) /*!< SCB CFSR (BFSR): BFARVALID Mask */ + +#define SCB_CFSR_STKERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 4U) /*!< SCB CFSR (BFSR): STKERR Position */ +#define SCB_CFSR_STKERR_Msk (1UL << SCB_CFSR_STKERR_Pos) /*!< SCB CFSR (BFSR): STKERR Mask */ + +#define SCB_CFSR_UNSTKERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 3U) /*!< SCB CFSR (BFSR): UNSTKERR Position */ +#define SCB_CFSR_UNSTKERR_Msk (1UL << SCB_CFSR_UNSTKERR_Pos) /*!< SCB CFSR (BFSR): UNSTKERR Mask */ + +#define SCB_CFSR_IMPRECISERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 2U) /*!< SCB CFSR (BFSR): IMPRECISERR Position */ +#define SCB_CFSR_IMPRECISERR_Msk (1UL << SCB_CFSR_IMPRECISERR_Pos) /*!< SCB CFSR (BFSR): IMPRECISERR Mask */ + +#define SCB_CFSR_PRECISERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 1U) /*!< SCB CFSR (BFSR): PRECISERR Position */ +#define SCB_CFSR_PRECISERR_Msk (1UL << SCB_CFSR_PRECISERR_Pos) /*!< SCB CFSR (BFSR): PRECISERR Mask */ + +#define SCB_CFSR_IBUSERR_Pos (SCB_CFSR_BUSFAULTSR_Pos + 0U) /*!< SCB CFSR (BFSR): IBUSERR Position */ +#define SCB_CFSR_IBUSERR_Msk (1UL << SCB_CFSR_IBUSERR_Pos) /*!< SCB CFSR (BFSR): IBUSERR Mask */ + +/* UsageFault Status Register (part of SCB Configurable Fault Status Register) */ +#define SCB_CFSR_DIVBYZERO_Pos (SCB_CFSR_USGFAULTSR_Pos + 9U) /*!< SCB CFSR (UFSR): DIVBYZERO Position */ +#define SCB_CFSR_DIVBYZERO_Msk (1UL << SCB_CFSR_DIVBYZERO_Pos) /*!< SCB CFSR (UFSR): DIVBYZERO Mask */ + +#define SCB_CFSR_UNALIGNED_Pos (SCB_CFSR_USGFAULTSR_Pos + 8U) /*!< SCB CFSR (UFSR): UNALIGNED Position */ +#define SCB_CFSR_UNALIGNED_Msk (1UL << SCB_CFSR_UNALIGNED_Pos) /*!< SCB CFSR (UFSR): UNALIGNED Mask */ + +#define SCB_CFSR_NOCP_Pos (SCB_CFSR_USGFAULTSR_Pos + 3U) /*!< SCB CFSR (UFSR): NOCP Position */ +#define SCB_CFSR_NOCP_Msk (1UL << SCB_CFSR_NOCP_Pos) /*!< SCB CFSR (UFSR): NOCP Mask */ + +#define SCB_CFSR_INVPC_Pos (SCB_CFSR_USGFAULTSR_Pos + 2U) /*!< SCB CFSR (UFSR): INVPC Position */ +#define SCB_CFSR_INVPC_Msk (1UL << SCB_CFSR_INVPC_Pos) /*!< SCB CFSR (UFSR): INVPC Mask */ + +#define SCB_CFSR_INVSTATE_Pos (SCB_CFSR_USGFAULTSR_Pos + 1U) /*!< SCB CFSR (UFSR): INVSTATE Position */ +#define SCB_CFSR_INVSTATE_Msk (1UL << SCB_CFSR_INVSTATE_Pos) /*!< SCB CFSR (UFSR): INVSTATE Mask */ + +#define SCB_CFSR_UNDEFINSTR_Pos (SCB_CFSR_USGFAULTSR_Pos + 0U) /*!< SCB CFSR (UFSR): UNDEFINSTR Position */ +#define SCB_CFSR_UNDEFINSTR_Msk (1UL << SCB_CFSR_UNDEFINSTR_Pos) /*!< SCB CFSR (UFSR): UNDEFINSTR Mask */ + /* SCB Hard Fault Status Register Definitions */ #define SCB_HFSR_DEBUGEVT_Pos 31U /*!< SCB HFSR: DEBUGEVT Position */ #define SCB_HFSR_DEBUGEVT_Msk (1UL << SCB_HFSR_DEBUGEVT_Pos) /*!< SCB HFSR: DEBUGEVT Mask */ @@ -966,7 +977,7 @@ typedef struct */ typedef struct { - __IOM uint32_t SSPSR; /*!< Offset: 0x000 (R/ ) Supported Parallel Port Size Register */ + __IM uint32_t SSPSR; /*!< Offset: 0x000 (R/ ) Supported Parallel Port Size Register */ __IOM uint32_t CSPSR; /*!< Offset: 0x004 (R/W) Current Parallel Port Size Register */ uint32_t RESERVED0[2U]; __IOM uint32_t ACPR; /*!< Offset: 0x010 (R/W) Asynchronous Clock Prescaler Register */ @@ -977,7 +988,7 @@ typedef struct __IOM uint32_t FFCR; /*!< Offset: 0x304 (R/W) Formatter and Flush Control Register */ __IM uint32_t FSCR; /*!< Offset: 0x308 (R/ ) Formatter Synchronization Counter Register */ uint32_t RESERVED3[759U]; - __IM uint32_t TRIGGER; /*!< Offset: 0xEE8 (R/ ) TRIGGER */ + __IM uint32_t TRIGGER; /*!< Offset: 0xEE8 (R/ ) TRIGGER Register */ __IM uint32_t FIFO0; /*!< Offset: 0xEEC (R/ ) Integration ETM Data */ __IM uint32_t ITATBCTR2; /*!< Offset: 0xEF0 (R/ ) ITATBCTR2 */ uint32_t RESERVED4[1U]; @@ -1047,8 +1058,11 @@ typedef struct #define TPI_FIFO0_ETM0_Msk (0xFFUL /*<< TPI_FIFO0_ETM0_Pos*/) /*!< TPI FIFO0: ETM0 Mask */ /* TPI ITATBCTR2 Register Definitions */ -#define TPI_ITATBCTR2_ATREADY_Pos 0U /*!< TPI ITATBCTR2: ATREADY Position */ -#define TPI_ITATBCTR2_ATREADY_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY_Pos*/) /*!< TPI ITATBCTR2: ATREADY Mask */ +#define TPI_ITATBCTR2_ATREADY2_Pos 0U /*!< TPI ITATBCTR2: ATREADY2 Position */ +#define TPI_ITATBCTR2_ATREADY2_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY2_Pos*/) /*!< TPI ITATBCTR2: ATREADY2 Mask */ + +#define TPI_ITATBCTR2_ATREADY1_Pos 0U /*!< TPI ITATBCTR2: ATREADY1 Position */ +#define TPI_ITATBCTR2_ATREADY1_Msk (0x1UL /*<< TPI_ITATBCTR2_ATREADY1_Pos*/) /*!< TPI ITATBCTR2: ATREADY1 Mask */ /* TPI Integration ITM Data Register Definitions (FIFO1) */ #define TPI_FIFO1_ITM_ATVALID_Pos 29U /*!< TPI FIFO1: ITM_ATVALID Position */ @@ -1073,12 +1087,15 @@ typedef struct #define TPI_FIFO1_ITM0_Msk (0xFFUL /*<< TPI_FIFO1_ITM0_Pos*/) /*!< TPI FIFO1: ITM0 Mask */ /* TPI ITATBCTR0 Register Definitions */ -#define TPI_ITATBCTR0_ATREADY_Pos 0U /*!< TPI ITATBCTR0: ATREADY Position */ -#define TPI_ITATBCTR0_ATREADY_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY_Pos*/) /*!< TPI ITATBCTR0: ATREADY Mask */ +#define TPI_ITATBCTR0_ATREADY2_Pos 0U /*!< TPI ITATBCTR0: ATREADY2 Position */ +#define TPI_ITATBCTR0_ATREADY2_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY2_Pos*/) /*!< TPI ITATBCTR0: ATREADY2 Mask */ + +#define TPI_ITATBCTR0_ATREADY1_Pos 0U /*!< TPI ITATBCTR0: ATREADY1 Position */ +#define TPI_ITATBCTR0_ATREADY1_Msk (0x1UL /*<< TPI_ITATBCTR0_ATREADY1_Pos*/) /*!< TPI ITATBCTR0: ATREADY1 Mask */ /* TPI Integration Mode Control Register Definitions */ #define TPI_ITCTRL_Mode_Pos 0U /*!< TPI ITCTRL: Mode Position */ -#define TPI_ITCTRL_Mode_Msk (0x1UL /*<< TPI_ITCTRL_Mode_Pos*/) /*!< TPI ITCTRL: Mode Mask */ +#define TPI_ITCTRL_Mode_Msk (0x3UL /*<< TPI_ITCTRL_Mode_Pos*/) /*!< TPI ITCTRL: Mode Mask */ /* TPI DEVID Register Definitions */ #define TPI_DEVID_NRZVALID_Pos 11U /*!< TPI DEVID: NRZVALID Position */ @@ -1100,16 +1117,16 @@ typedef struct #define TPI_DEVID_NrTraceInput_Msk (0x1FUL /*<< TPI_DEVID_NrTraceInput_Pos*/) /*!< TPI DEVID: NrTraceInput Mask */ /* TPI DEVTYPE Register Definitions */ -#define TPI_DEVTYPE_MajorType_Pos 4U /*!< TPI DEVTYPE: MajorType Position */ -#define TPI_DEVTYPE_MajorType_Msk (0xFUL << TPI_DEVTYPE_MajorType_Pos) /*!< TPI DEVTYPE: MajorType Mask */ - -#define TPI_DEVTYPE_SubType_Pos 0U /*!< TPI DEVTYPE: SubType Position */ +#define TPI_DEVTYPE_SubType_Pos 4U /*!< TPI DEVTYPE: SubType Position */ #define TPI_DEVTYPE_SubType_Msk (0xFUL /*<< TPI_DEVTYPE_SubType_Pos*/) /*!< TPI DEVTYPE: SubType Mask */ +#define TPI_DEVTYPE_MajorType_Pos 0U /*!< TPI DEVTYPE: MajorType Position */ +#define TPI_DEVTYPE_MajorType_Msk (0xFUL << TPI_DEVTYPE_MajorType_Pos) /*!< TPI DEVTYPE: MajorType Mask */ + /*@}*/ /* end of group CMSIS_TPI */ -#if (__MPU_PRESENT == 1U) +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) /** \ingroup CMSIS_core_register \defgroup CMSIS_MPU Memory Protection Unit (MPU) @@ -1319,18 +1336,18 @@ typedef struct /** \brief Mask and shift a bit field value for use in a register bit range. \param[in] field Name of the register bit field. - \param[in] value Value of the bit field. + \param[in] value Value of the bit field. This parameter is interpreted as an uint32_t type. \return Masked and shifted value. */ -#define _VAL2FLD(field, value) ((value << field ## _Pos) & field ## _Msk) +#define _VAL2FLD(field, value) (((uint32_t)(value) << field ## _Pos) & field ## _Msk) /** \brief Mask and shift a register value to extract a bit filed value. \param[in] field Name of the register bit field. - \param[in] value Value of register. + \param[in] value Value of register. This parameter is interpreted as an uint32_t type. \return Masked and shifted bit field value. */ -#define _FLD2VAL(field, value) ((value & field ## _Msk) >> field ## _Pos) +#define _FLD2VAL(field, value) (((uint32_t)(value) & field ## _Msk) >> field ## _Pos) /*@} end of group CMSIS_core_bitfield */ @@ -1342,7 +1359,7 @@ typedef struct @{ */ -/* Memory mapping of Cortex-M3 Hardware */ +/* Memory mapping of Core Hardware */ #define SCS_BASE (0xE000E000UL) /*!< System Control Space Base Address */ #define ITM_BASE (0xE0000000UL) /*!< ITM Base Address */ #define DWT_BASE (0xE0001000UL) /*!< DWT Base Address */ @@ -1361,7 +1378,7 @@ typedef struct #define TPI ((TPI_Type *) TPI_BASE ) /*!< TPI configuration struct */ #define CoreDebug ((CoreDebug_Type *) CoreDebug_BASE) /*!< Core Debug configuration struct */ -#if (__MPU_PRESENT == 1U) +#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1U) #define MPU_BASE (SCS_BASE + 0x0D90UL) /*!< Memory Protection Unit */ #define MPU ((MPU_Type *) MPU_BASE ) /*!< Memory Protection Unit */ #endif @@ -1392,6 +1409,46 @@ typedef struct @{ */ +#ifdef CMSIS_NVIC_VIRTUAL +#ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE +#define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h" +#endif +#include CMSIS_NVIC_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetPriorityGrouping __NVIC_SetPriorityGrouping +#define NVIC_GetPriorityGrouping __NVIC_GetPriorityGrouping +#define NVIC_EnableIRQ __NVIC_EnableIRQ +#define NVIC_GetEnableIRQ __NVIC_GetEnableIRQ +#define NVIC_DisableIRQ __NVIC_DisableIRQ +#define NVIC_GetPendingIRQ __NVIC_GetPendingIRQ +#define NVIC_SetPendingIRQ __NVIC_SetPendingIRQ +#define NVIC_ClearPendingIRQ __NVIC_ClearPendingIRQ +#define NVIC_GetActive __NVIC_GetActive +#define NVIC_SetPriority __NVIC_SetPriority +#define NVIC_GetPriority __NVIC_GetPriority +#define NVIC_SystemReset __NVIC_SystemReset +#endif /* CMSIS_NVIC_VIRTUAL */ + +#ifdef CMSIS_VECTAB_VIRTUAL +#ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h" +#endif +#include CMSIS_VECTAB_VIRTUAL_HEADER_FILE +#else +#define NVIC_SetVector __NVIC_SetVector +#define NVIC_GetVector __NVIC_GetVector +#endif /* (CMSIS_VECTAB_VIRTUAL) */ + +#define NVIC_USER_IRQ_OFFSET 16 + + +/* The following EXC_RETURN values are saved the LR on exception entry */ +#define EXC_RETURN_HANDLER (0xFFFFFFF1UL) /* return to Handler mode, uses MSP after return */ +#define EXC_RETURN_THREAD_MSP (0xFFFFFFF9UL) /* return to Thread mode, uses MSP after return */ +#define EXC_RETURN_THREAD_PSP (0xFFFFFFFDUL) /* return to Thread mode, uses PSP after return */ + + + /** \brief Set Priority Grouping \details Sets the priority grouping field using the required unlock sequence. @@ -1401,10 +1458,11 @@ typedef struct priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set. \param [in] PriorityGroup Priority grouping field. */ -__STATIC_INLINE void NVIC_SetPriorityGrouping(uint32_t PriorityGroup) +__STATIC_INLINE void __NVIC_SetPriorityGrouping(uint32_t PriorityGroup) { uint32_t reg_value; uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ + reg_value = SCB->AIRCR; /* read old register configuration */ reg_value &= ~((uint32_t)(SCB_AIRCR_VECTKEY_Msk | SCB_AIRCR_PRIGROUP_Msk)); /* clear bits to change */ reg_value = (reg_value | @@ -1419,120 +1477,178 @@ __STATIC_INLINE void NVIC_SetPriorityGrouping(uint32_t PriorityGroup) \details Reads the priority grouping field from the NVIC Interrupt Controller. \return Priority grouping field (SCB->AIRCR [10:8] PRIGROUP field). */ -__STATIC_INLINE uint32_t NVIC_GetPriorityGrouping(void) +__STATIC_INLINE uint32_t __NVIC_GetPriorityGrouping(void) { return ((uint32_t)((SCB->AIRCR & SCB_AIRCR_PRIGROUP_Msk) >> SCB_AIRCR_PRIGROUP_Pos)); } /** - \brief Enable External Interrupt - \details Enables a device-specific interrupt in the NVIC interrupt controller. - \param [in] IRQn External interrupt number. Value cannot be negative. + \brief Enable Interrupt + \details Enables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. + */ +__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn) +{ + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } +} + + +/** + \brief Get Interrupt Enable status + \details Returns a device specific interrupt enable status from the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \return 0 Interrupt is not enabled. + \return 1 Interrupt is enabled. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_EnableIRQ(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn) { - NVIC->ISER[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISER[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** - \brief Disable External Interrupt - \details Disables a device-specific interrupt in the NVIC interrupt controller. - \param [in] IRQn External interrupt number. Value cannot be negative. + \brief Disable Interrupt + \details Disables a device specific interrupt in the NVIC interrupt controller. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_DisableIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn) { - NVIC->ICER[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICER[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + __DSB(); + __ISB(); + } } /** \brief Get Pending Interrupt - \details Reads the pending register in the NVIC and returns the pending bit for the specified interrupt. - \param [in] IRQn Interrupt number. + \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt. + \param [in] IRQn Device specific interrupt number. \return 0 Interrupt status is not pending. \return 1 Interrupt status is pending. + \note IRQn must not be negative. */ -__STATIC_INLINE uint32_t NVIC_GetPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn) { - return ((uint32_t)(((NVIC->ISPR[(((uint32_t)(int32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** \brief Set Pending Interrupt - \details Sets the pending bit of an external interrupt. - \param [in] IRQn Interrupt number. Value cannot be negative. + \details Sets the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_SetPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn) { - NVIC->ISPR[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ISPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** \brief Clear Pending Interrupt - \details Clears the pending bit of an external interrupt. - \param [in] IRQn External interrupt number. Value cannot be negative. + \details Clears the pending bit of a device specific interrupt in the NVIC pending register. + \param [in] IRQn Device specific interrupt number. + \note IRQn must not be negative. */ -__STATIC_INLINE void NVIC_ClearPendingIRQ(IRQn_Type IRQn) +__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn) { - NVIC->ICPR[(((uint32_t)(int32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL)); + if ((int32_t)(IRQn) >= 0) + { + NVIC->ICPR[(((uint32_t)IRQn) >> 5UL)] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL)); + } } /** \brief Get Active Interrupt - \details Reads the active register in NVIC and returns the active bit. - \param [in] IRQn Interrupt number. + \details Reads the active register in the NVIC and returns the active bit for the device specific interrupt. + \param [in] IRQn Device specific interrupt number. \return 0 Interrupt status is not active. \return 1 Interrupt status is active. + \note IRQn must not be negative. */ -__STATIC_INLINE uint32_t NVIC_GetActive(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetActive(IRQn_Type IRQn) { - return ((uint32_t)(((NVIC->IABR[(((uint32_t)(int32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)(int32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + if ((int32_t)(IRQn) >= 0) + { + return ((uint32_t)(((NVIC->IABR[(((uint32_t)IRQn) >> 5UL)] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL)); + } + else + { + return (0U); + } } /** \brief Set Interrupt Priority - \details Sets the priority of an interrupt. - \note The priority cannot be set for every core interrupt. + \details Sets the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. \param [in] IRQn Interrupt number. \param [in] priority Priority to set. + \note The priority cannot be set for every processor exception. */ -__STATIC_INLINE void NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) +__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority) { - if ((int32_t)(IRQn) < 0) + if ((int32_t)(IRQn) >= 0) { - SCB->SHP[(((uint32_t)(int32_t)IRQn) & 0xFUL) - 4UL] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + NVIC->IP[((uint32_t)IRQn)] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); } else { - NVIC->IP[((uint32_t)(int32_t)IRQn)] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); + SCB->SHP[(((uint32_t)IRQn) & 0xFUL) - 4UL] = (uint8_t)((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL); } } /** \brief Get Interrupt Priority - \details Reads the priority of an interrupt. - The interrupt number can be positive to specify an external (device specific) interrupt, - or negative to specify an internal (core) interrupt. + \details Reads the priority of a device specific interrupt or a processor exception. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. \param [in] IRQn Interrupt number. \return Interrupt Priority. Value is aligned automatically to the implemented priority bits of the microcontroller. */ -__STATIC_INLINE uint32_t NVIC_GetPriority(IRQn_Type IRQn) +__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn) { - if ((int32_t)(IRQn) < 0) + + if ((int32_t)(IRQn) >= 0) { - return (((uint32_t)SCB->SHP[(((uint32_t)(int32_t)IRQn) & 0xFUL) - 4UL] >> (8U - __NVIC_PRIO_BITS))); + return (((uint32_t)NVIC->IP[((uint32_t)IRQn)] >> (8U - __NVIC_PRIO_BITS))); } else { - return (((uint32_t)NVIC->IP[((uint32_t)(int32_t)IRQn)] >> (8U - __NVIC_PRIO_BITS))); + return (((uint32_t)SCB->SHP[(((uint32_t)IRQn) & 0xFUL) - 4UL] >> (8U - __NVIC_PRIO_BITS))); } } @@ -1553,8 +1669,10 @@ __STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t P uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ uint32_t PreemptPriorityBits; uint32_t SubPriorityBits; + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + return ( ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) | ((SubPriority & (uint32_t)((1UL << (SubPriorityBits )) - 1UL))) @@ -1578,18 +1696,51 @@ __STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGr uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL); /* only values 0..7 are used */ uint32_t PreemptPriorityBits; uint32_t SubPriorityBits; + PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp); SubPriorityBits = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS)); + *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL); *pSubPriority = (Priority ) & (uint32_t)((1UL << (SubPriorityBits )) - 1UL); } +/** + \brief Set Interrupt Vector + \details Sets an interrupt vector in SRAM based interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + VTOR must been relocated to SRAM before. + \param [in] IRQn Interrupt number + \param [in] vector Address of interrupt handler function + */ +__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector) +{ + uint32_t* vectors = (uint32_t*)SCB->VTOR; + vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector; +} + + +/** + \brief Get Interrupt Vector + \details Reads an interrupt vector from interrupt vector table. + The interrupt number can be positive to specify a device specific interrupt, + or negative to specify a processor exception. + \param [in] IRQn Interrupt number. + \return Address of interrupt handler function + */ +__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn) +{ + uint32_t* vectors = (uint32_t*)SCB->VTOR; + return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET]; +} + + /** \brief System Reset \details Initiates a system reset request to reset the MCU. */ -__STATIC_INLINE void NVIC_SystemReset(void) +__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void) { __DSB(); /* Ensure all outstanding memory accesses included buffered write are completed before reset */ @@ -1607,6 +1758,31 @@ __STATIC_INLINE void NVIC_SystemReset(void) /*@} end of CMSIS_Core_NVICFunctions */ +/* ########################## FPU functions #################################### */ +/** + \ingroup CMSIS_Core_FunctionInterface + \defgroup CMSIS_Core_FpuFunctions FPU Functions + \brief Function that provides FPU type. + @{ + */ + +/** + \brief get FPU type + \details returns the FPU type + \returns + - \b 0: No FPU + - \b 1: Single precision FPU + - \b 2: Double + Single precision FPU + */ +__STATIC_INLINE uint32_t SCB_GetFPUType(void) +{ + return 0U; /* No FPU */ +} + + +/*@} end of CMSIS_Core_FpuFunctions */ + + /* ################################## SysTick function ############################################ */ /** @@ -1616,7 +1792,7 @@ __STATIC_INLINE void NVIC_SystemReset(void) @{ */ -#if (__Vendor_SysTickConfig == 0U) +#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U) /** \brief System Tick Configuration @@ -1659,8 +1835,8 @@ __STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks) @{ */ -extern volatile int32_t ITM_RxBuffer; /*!< External variable to receive characters. */ -#define ITM_RXBUFFER_EMPTY 0x5AA55AA5U /*!< Value identifying \ref ITM_RxBuffer is ready for next character. */ +extern volatile int32_t ITM_RxBuffer; /*!< External variable to receive characters. */ +#define ITM_RXBUFFER_EMPTY ((int32_t)0x5AA55AA5U) /*!< Value identifying \ref ITM_RxBuffer is ready for next character. */ /** @@ -1716,6 +1892,7 @@ __STATIC_INLINE int32_t ITM_ReceiveChar (void) */ __STATIC_INLINE int32_t ITM_CheckChar (void) { + if (ITM_RxBuffer == ITM_RXBUFFER_EMPTY) { return (0); /* no character available */ diff --git a/EpsilonLights/Drivers/CMSIS/Include/mpu_armv7.h b/EpsilonLights/Drivers/CMSIS/Include/mpu_armv7.h new file mode 100644 index 00000000..ee510d37 --- /dev/null +++ b/EpsilonLights/Drivers/CMSIS/Include/mpu_armv7.h @@ -0,0 +1,275 @@ +/****************************************************************************** + * @file mpu_armv7.h + * @brief CMSIS MPU API for Armv7-M MPU + * @version V5.0.4 + * @date 10. January 2018 + ******************************************************************************/ +/* + * Copyright (c) 2017-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ + +#if defined ( __ICCARM__ ) +#pragma system_include /* treat file as system include file for MISRA check */ +#elif defined (__clang__) +#pragma clang system_header /* treat file as system include file */ +#endif + +#ifndef ARM_MPU_ARMV7_H +#define ARM_MPU_ARMV7_H + +#define ARM_MPU_REGION_SIZE_32B ((uint8_t)0x04U) ///!< MPU Region Size 32 Bytes +#define ARM_MPU_REGION_SIZE_64B ((uint8_t)0x05U) ///!< MPU Region Size 64 Bytes +#define ARM_MPU_REGION_SIZE_128B ((uint8_t)0x06U) ///!< MPU Region Size 128 Bytes +#define ARM_MPU_REGION_SIZE_256B ((uint8_t)0x07U) ///!< MPU Region Size 256 Bytes +#define ARM_MPU_REGION_SIZE_512B ((uint8_t)0x08U) ///!< MPU Region Size 512 Bytes +#define ARM_MPU_REGION_SIZE_1KB ((uint8_t)0x09U) ///!< MPU Region Size 1 KByte +#define ARM_MPU_REGION_SIZE_2KB ((uint8_t)0x0AU) ///!< MPU Region Size 2 KBytes +#define ARM_MPU_REGION_SIZE_4KB ((uint8_t)0x0BU) ///!< MPU Region Size 4 KBytes +#define ARM_MPU_REGION_SIZE_8KB ((uint8_t)0x0CU) ///!< MPU Region Size 8 KBytes +#define ARM_MPU_REGION_SIZE_16KB ((uint8_t)0x0DU) ///!< MPU Region Size 16 KBytes +#define ARM_MPU_REGION_SIZE_32KB ((uint8_t)0x0EU) ///!< MPU Region Size 32 KBytes +#define ARM_MPU_REGION_SIZE_64KB ((uint8_t)0x0FU) ///!< MPU Region Size 64 KBytes +#define ARM_MPU_REGION_SIZE_128KB ((uint8_t)0x10U) ///!< MPU Region Size 128 KBytes +#define ARM_MPU_REGION_SIZE_256KB ((uint8_t)0x11U) ///!< MPU Region Size 256 KBytes +#define ARM_MPU_REGION_SIZE_512KB ((uint8_t)0x12U) ///!< MPU Region Size 512 KBytes +#define ARM_MPU_REGION_SIZE_1MB ((uint8_t)0x13U) ///!< MPU Region Size 1 MByte +#define ARM_MPU_REGION_SIZE_2MB ((uint8_t)0x14U) ///!< MPU Region Size 2 MBytes +#define ARM_MPU_REGION_SIZE_4MB ((uint8_t)0x15U) ///!< MPU Region Size 4 MBytes +#define ARM_MPU_REGION_SIZE_8MB ((uint8_t)0x16U) ///!< MPU Region Size 8 MBytes +#define ARM_MPU_REGION_SIZE_16MB ((uint8_t)0x17U) ///!< MPU Region Size 16 MBytes +#define ARM_MPU_REGION_SIZE_32MB ((uint8_t)0x18U) ///!< MPU Region Size 32 MBytes +#define ARM_MPU_REGION_SIZE_64MB ((uint8_t)0x19U) ///!< MPU Region Size 64 MBytes +#define ARM_MPU_REGION_SIZE_128MB ((uint8_t)0x1AU) ///!< MPU Region Size 128 MBytes +#define ARM_MPU_REGION_SIZE_256MB ((uint8_t)0x1BU) ///!< MPU Region Size 256 MBytes +#define ARM_MPU_REGION_SIZE_512MB ((uint8_t)0x1CU) ///!< MPU Region Size 512 MBytes +#define ARM_MPU_REGION_SIZE_1GB ((uint8_t)0x1DU) ///!< MPU Region Size 1 GByte +#define ARM_MPU_REGION_SIZE_2GB ((uint8_t)0x1EU) ///!< MPU Region Size 2 GBytes +#define ARM_MPU_REGION_SIZE_4GB ((uint8_t)0x1FU) ///!< MPU Region Size 4 GBytes + +#define ARM_MPU_AP_NONE 0U ///!< MPU Access Permission no access +#define ARM_MPU_AP_PRIV 1U ///!< MPU Access Permission privileged access only +#define ARM_MPU_AP_URO 2U ///!< MPU Access Permission unprivileged access read-only +#define ARM_MPU_AP_FULL 3U ///!< MPU Access Permission full access +#define ARM_MPU_AP_PRO 5U ///!< MPU Access Permission privileged access read-only +#define ARM_MPU_AP_RO 6U ///!< MPU Access Permission read-only access + +/** MPU Region Base Address Register Value +* +* \param Region The region to be configured, number 0 to 15. +* \param BaseAddress The base address for the region. +*/ +#define ARM_MPU_RBAR(Region, BaseAddress) \ + (((BaseAddress) & MPU_RBAR_ADDR_Msk) | \ + ((Region) & MPU_RBAR_REGION_Msk) | \ + (MPU_RBAR_VALID_Msk)) + +/** +* MPU Memory Access Attributes +* +* \param TypeExtField Type extension field, allows you to configure memory access type, for example strongly ordered, peripheral. +* \param IsShareable Region is shareable between multiple bus masters. +* \param IsCacheable Region is cacheable, i.e. its value may be kept in cache. +* \param IsBufferable Region is bufferable, i.e. using write-back caching. Cacheable but non-bufferable regions use write-through policy. +*/ +#define ARM_MPU_ACCESS_(TypeExtField, IsShareable, IsCacheable, IsBufferable) \ + ((((TypeExtField ) << MPU_RASR_TEX_Pos) & MPU_RASR_TEX_Msk) | \ + (((IsShareable ) << MPU_RASR_S_Pos) & MPU_RASR_S_Msk) | \ + (((IsCacheable ) << MPU_RASR_C_Pos) & MPU_RASR_C_Msk) | \ + (((IsBufferable ) << MPU_RASR_B_Pos) & MPU_RASR_B_Msk)) + +/** +* MPU Region Attribute and Size Register Value +* +* \param DisableExec Instruction access disable bit, 1= disable instruction fetches. +* \param AccessPermission Data access permissions, allows you to configure read/write access for User and Privileged mode. +* \param AccessAttributes Memory access attribution, see \ref ARM_MPU_ACCESS_. +* \param SubRegionDisable Sub-region disable field. +* \param Size Region size of the region to be configured, for example 4K, 8K. +*/ +#define ARM_MPU_RASR_EX(DisableExec, AccessPermission, AccessAttributes, SubRegionDisable, Size) \ + ((((DisableExec ) << MPU_RASR_XN_Pos) & MPU_RASR_XN_Msk) | \ + (((AccessPermission) << MPU_RASR_AP_Pos) & MPU_RASR_AP_Msk) | \ + (((AccessAttributes) ) & (MPU_RASR_TEX_Msk | MPU_RASR_S_Msk | MPU_RASR_C_Msk | MPU_RASR_B_Msk))) + +/** +* MPU Region Attribute and Size Register Value +* +* \param DisableExec Instruction access disable bit, 1= disable instruction fetches. +* \param AccessPermission Data access permissions, allows you to configure read/write access for User and Privileged mode. +* \param TypeExtField Type extension field, allows you to configure memory access type, for example strongly ordered, peripheral. +* \param IsShareable Region is shareable between multiple bus masters. +* \param IsCacheable Region is cacheable, i.e. its value may be kept in cache. +* \param IsBufferable Region is bufferable, i.e. using write-back caching. Cacheable but non-bufferable regions use write-through policy. +* \param SubRegionDisable Sub-region disable field. +* \param Size Region size of the region to be configured, for example 4K, 8K. +*/ +#define ARM_MPU_RASR(DisableExec, AccessPermission, TypeExtField, IsShareable, IsCacheable, IsBufferable, SubRegionDisable, Size) \ + ARM_MPU_RASR_EX(DisableExec, AccessPermission, ARM_MPU_ACCESS_(TypeExtField, IsShareable, IsCacheable, IsBufferable), SubRegionDisable, Size) + +/** +* MPU Memory Access Attribute for strongly ordered memory. +* - TEX: 000b +* - Shareable +* - Non-cacheable +* - Non-bufferable +*/ +#define ARM_MPU_ACCESS_ORDERED ARM_MPU_ACCESS_(0U, 1U, 0U, 0U) + +/** +* MPU Memory Access Attribute for device memory. +* - TEX: 000b (if non-shareable) or 010b (if shareable) +* - Shareable or non-shareable +* - Non-cacheable +* - Bufferable (if shareable) or non-bufferable (if non-shareable) +* +* \param IsShareable Configures the device memory as shareable or non-shareable. +*/ +#define ARM_MPU_ACCESS_DEVICE(IsShareable) ((IsShareable) ? ARM_MPU_ACCESS_(0U, 1U, 0U, 1U) : ARM_MPU_ACCESS_(2U, 0U, 0U, 0U)) + +/** +* MPU Memory Access Attribute for normal memory. +* - TEX: 1BBb (reflecting outer cacheability rules) +* - Shareable or non-shareable +* - Cacheable or non-cacheable (reflecting inner cacheability rules) +* - Bufferable or non-bufferable (reflecting inner cacheability rules) +* +* \param OuterCp Configures the outer cache policy. +* \param InnerCp Configures the inner cache policy. +* \param IsShareable Configures the memory as shareable or non-shareable. +*/ +#define ARM_MPU_ACCESS_NORMAL(OuterCp, InnerCp, IsShareable) ARM_MPU_ACCESS_((4U | (OuterCp)), IsShareable, ((InnerCp) & 2U), ((InnerCp) & 1U)) + +/** +* MPU Memory Access Attribute non-cacheable policy. +*/ +#define ARM_MPU_CACHEP_NOCACHE 0U + +/** +* MPU Memory Access Attribute write-back, write and read allocate policy. +*/ +#define ARM_MPU_CACHEP_WB_WRA 1U + +/** +* MPU Memory Access Attribute write-through, no write allocate policy. +*/ +#define ARM_MPU_CACHEP_WT_NWA 2U + +/** +* MPU Memory Access Attribute write-back, no write allocate policy. +*/ +#define ARM_MPU_CACHEP_WB_NWA 3U + + +/** +* Struct for a single MPU Region +*/ +typedef struct +{ + uint32_t RBAR; //!< The region base address register value (RBAR) + uint32_t RASR; //!< The region attribute and size register value (RASR) \ref MPU_RASR +} ARM_MPU_Region_t; + +/** Enable the MPU. +* \param MPU_Control Default access permissions for unconfigured regions. +*/ +__STATIC_INLINE void ARM_MPU_Enable(uint32_t MPU_Control) +{ + __DSB(); + __ISB(); + MPU->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk; +#ifdef SCB_SHCSR_MEMFAULTENA_Msk + SCB->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk; +#endif +} + +/** Disable the MPU. +*/ +__STATIC_INLINE void ARM_MPU_Disable(void) +{ + __DSB(); + __ISB(); +#ifdef SCB_SHCSR_MEMFAULTENA_Msk + SCB->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk; +#endif + MPU->CTRL &= ~MPU_CTRL_ENABLE_Msk; +} + +/** Clear and disable the given MPU region. +* \param rnr Region number to be cleared. +*/ +__STATIC_INLINE void ARM_MPU_ClrRegion(uint32_t rnr) +{ + MPU->RNR = rnr; + MPU->RASR = 0U; +} + +/** Configure an MPU region. +* \param rbar Value for RBAR register. +* \param rsar Value for RSAR register. +*/ +__STATIC_INLINE void ARM_MPU_SetRegion(uint32_t rbar, uint32_t rasr) +{ + MPU->RBAR = rbar; + MPU->RASR = rasr; +} + +/** Configure the given MPU region. +* \param rnr Region number to be configured. +* \param rbar Value for RBAR register. +* \param rsar Value for RSAR register. +*/ +__STATIC_INLINE void ARM_MPU_SetRegionEx(uint32_t rnr, uint32_t rbar, uint32_t rasr) +{ + MPU->RNR = rnr; + MPU->RBAR = rbar; + MPU->RASR = rasr; +} + +/** Memcopy with strictly ordered memory access, e.g. for register targets. +* \param dst Destination data is copied to. +* \param src Source data is copied from. +* \param len Amount of data words to be copied. +*/ +__STATIC_INLINE void orderedCpy(volatile uint32_t* dst, const uint32_t* __RESTRICT src, uint32_t len) +{ + uint32_t i; + + for (i = 0U; i < len; ++i) + { + dst[i] = src[i]; + } +} + +/** Load the given number of MPU regions from a table. +* \param table Pointer to the MPU configuration table. +* \param cnt Amount of regions to be configured. +*/ +__STATIC_INLINE void ARM_MPU_Load(ARM_MPU_Region_t const* table, uint32_t cnt) +{ + const uint32_t rowWordSize = sizeof(ARM_MPU_Region_t) / 4U; + + while (cnt > MPU_TYPE_RALIASES) + { + orderedCpy(&(MPU->RBAR), &(table->RBAR), MPU_TYPE_RALIASES * rowWordSize); + table += MPU_TYPE_RALIASES; + cnt -= MPU_TYPE_RALIASES; + } + + orderedCpy(&(MPU->RBAR), &(table->RBAR), cnt * rowWordSize); +} + +#endif diff --git a/EpsilonLights/Drivers/CMSIS/Include/mpu_armv8.h b/EpsilonLights/Drivers/CMSIS/Include/mpu_armv8.h new file mode 100644 index 00000000..767cc943 --- /dev/null +++ b/EpsilonLights/Drivers/CMSIS/Include/mpu_armv8.h @@ -0,0 +1,342 @@ +/****************************************************************************** + * @file mpu_armv8.h + * @brief CMSIS MPU API for Armv8-M MPU + * @version V5.0.4 + * @date 10. January 2018 + ******************************************************************************/ +/* + * Copyright (c) 2017-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ + +#if defined ( __ICCARM__ ) +#pragma system_include /* treat file as system include file for MISRA check */ +#elif defined (__clang__) +#pragma clang system_header /* treat file as system include file */ +#endif + +#ifndef ARM_MPU_ARMV8_H +#define ARM_MPU_ARMV8_H + +/** \brief Attribute for device memory (outer only) */ +#define ARM_MPU_ATTR_DEVICE ( 0U ) + +/** \brief Attribute for non-cacheable, normal memory */ +#define ARM_MPU_ATTR_NON_CACHEABLE ( 4U ) + +/** \brief Attribute for normal memory (outer and inner) +* \param NT Non-Transient: Set to 1 for non-transient data. +* \param WB Write-Back: Set to 1 to use write-back update policy. +* \param RA Read Allocation: Set to 1 to use cache allocation on read miss. +* \param WA Write Allocation: Set to 1 to use cache allocation on write miss. +*/ +#define ARM_MPU_ATTR_MEMORY_(NT, WB, RA, WA) \ + (((NT & 1U) << 3U) | ((WB & 1U) << 2U) | ((RA & 1U) << 1U) | (WA & 1U)) + +/** \brief Device memory type non Gathering, non Re-ordering, non Early Write Acknowledgement */ +#define ARM_MPU_ATTR_DEVICE_nGnRnE (0U) + +/** \brief Device memory type non Gathering, non Re-ordering, Early Write Acknowledgement */ +#define ARM_MPU_ATTR_DEVICE_nGnRE (1U) + +/** \brief Device memory type non Gathering, Re-ordering, Early Write Acknowledgement */ +#define ARM_MPU_ATTR_DEVICE_nGRE (2U) + +/** \brief Device memory type Gathering, Re-ordering, Early Write Acknowledgement */ +#define ARM_MPU_ATTR_DEVICE_GRE (3U) + +/** \brief Memory Attribute +* \param O Outer memory attributes +* \param I O == ARM_MPU_ATTR_DEVICE: Device memory attributes, else: Inner memory attributes +*/ +#define ARM_MPU_ATTR(O, I) (((O & 0xFU) << 4U) | (((O & 0xFU) != 0U) ? (I & 0xFU) : ((I & 0x3U) << 2U))) + +/** \brief Normal memory non-shareable */ +#define ARM_MPU_SH_NON (0U) + +/** \brief Normal memory outer shareable */ +#define ARM_MPU_SH_OUTER (2U) + +/** \brief Normal memory inner shareable */ +#define ARM_MPU_SH_INNER (3U) + +/** \brief Memory access permissions +* \param RO Read-Only: Set to 1 for read-only memory. +* \param NP Non-Privileged: Set to 1 for non-privileged memory. +*/ +#define ARM_MPU_AP_(RO, NP) (((RO & 1U) << 1U) | (NP & 1U)) + +/** \brief Region Base Address Register value +* \param BASE The base address bits [31:5] of a memory region. The value is zero extended. Effective address gets 32 byte aligned. +* \param SH Defines the Shareability domain for this memory region. +* \param RO Read-Only: Set to 1 for a read-only memory region. +* \param NP Non-Privileged: Set to 1 for a non-privileged memory region. +* \oaram XN eXecute Never: Set to 1 for a non-executable memory region. +*/ +#define ARM_MPU_RBAR(BASE, SH, RO, NP, XN) \ + ((BASE & MPU_RBAR_BASE_Msk) | \ + ((SH << MPU_RBAR_SH_Pos) & MPU_RBAR_SH_Msk) | \ + ((ARM_MPU_AP_(RO, NP) << MPU_RBAR_AP_Pos) & MPU_RBAR_AP_Msk) | \ + ((XN << MPU_RBAR_XN_Pos) & MPU_RBAR_XN_Msk)) + +/** \brief Region Limit Address Register value +* \param LIMIT The limit address bits [31:5] for this memory region. The value is one extended. +* \param IDX The attribute index to be associated with this memory region. +*/ +#define ARM_MPU_RLAR(LIMIT, IDX) \ + ((LIMIT & MPU_RLAR_LIMIT_Msk) | \ + ((IDX << MPU_RLAR_AttrIndx_Pos) & MPU_RLAR_AttrIndx_Msk) | \ + (MPU_RLAR_EN_Msk)) + +/** +* Struct for a single MPU Region +*/ +typedef struct +{ + uint32_t RBAR; /*!< Region Base Address Register value */ + uint32_t RLAR; /*!< Region Limit Address Register value */ +} ARM_MPU_Region_t; + +/** Enable the MPU. +* \param MPU_Control Default access permissions for unconfigured regions. +*/ +__STATIC_INLINE void ARM_MPU_Enable(uint32_t MPU_Control) +{ + __DSB(); + __ISB(); + MPU->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk; +#ifdef SCB_SHCSR_MEMFAULTENA_Msk + SCB->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk; +#endif +} + +/** Disable the MPU. +*/ +__STATIC_INLINE void ARM_MPU_Disable(void) +{ + __DSB(); + __ISB(); +#ifdef SCB_SHCSR_MEMFAULTENA_Msk + SCB->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk; +#endif + MPU->CTRL &= ~MPU_CTRL_ENABLE_Msk; +} + +#ifdef MPU_NS +/** Enable the Non-secure MPU. +* \param MPU_Control Default access permissions for unconfigured regions. +*/ +__STATIC_INLINE void ARM_MPU_Enable_NS(uint32_t MPU_Control) +{ + __DSB(); + __ISB(); + MPU_NS->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk; +#ifdef SCB_SHCSR_MEMFAULTENA_Msk + SCB_NS->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk; +#endif +} + +/** Disable the Non-secure MPU. +*/ +__STATIC_INLINE void ARM_MPU_Disable_NS(void) +{ + __DSB(); + __ISB(); +#ifdef SCB_SHCSR_MEMFAULTENA_Msk + SCB_NS->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk; +#endif + MPU_NS->CTRL &= ~MPU_CTRL_ENABLE_Msk; +} +#endif + +/** Set the memory attribute encoding to the given MPU. +* \param mpu Pointer to the MPU to be configured. +* \param idx The attribute index to be set [0-7] +* \param attr The attribute value to be set. +*/ +__STATIC_INLINE void ARM_MPU_SetMemAttrEx(MPU_Type* mpu, uint8_t idx, uint8_t attr) +{ + const uint8_t reg = idx / 4U; + const uint32_t pos = ((idx % 4U) * 8U); + const uint32_t mask = 0xFFU << pos; + + if (reg >= (sizeof(mpu->MAIR) / sizeof(mpu->MAIR[0]))) + { + return; // invalid index + } + + mpu->MAIR[reg] = ((mpu->MAIR[reg] & ~mask) | ((attr << pos) & mask)); +} + +/** Set the memory attribute encoding. +* \param idx The attribute index to be set [0-7] +* \param attr The attribute value to be set. +*/ +__STATIC_INLINE void ARM_MPU_SetMemAttr(uint8_t idx, uint8_t attr) +{ + ARM_MPU_SetMemAttrEx(MPU, idx, attr); +} + +#ifdef MPU_NS +/** Set the memory attribute encoding to the Non-secure MPU. +* \param idx The attribute index to be set [0-7] +* \param attr The attribute value to be set. +*/ +__STATIC_INLINE void ARM_MPU_SetMemAttr_NS(uint8_t idx, uint8_t attr) +{ + ARM_MPU_SetMemAttrEx(MPU_NS, idx, attr); +} +#endif + +/** Clear and disable the given MPU region of the given MPU. +* \param mpu Pointer to MPU to be used. +* \param rnr Region number to be cleared. +*/ +__STATIC_INLINE void ARM_MPU_ClrRegionEx(MPU_Type* mpu, uint32_t rnr) +{ + mpu->RNR = rnr; + mpu->RLAR = 0U; +} + +/** Clear and disable the given MPU region. +* \param rnr Region number to be cleared. +*/ +__STATIC_INLINE void ARM_MPU_ClrRegion(uint32_t rnr) +{ + ARM_MPU_ClrRegionEx(MPU, rnr); +} + +#ifdef MPU_NS +/** Clear and disable the given Non-secure MPU region. +* \param rnr Region number to be cleared. +*/ +__STATIC_INLINE void ARM_MPU_ClrRegion_NS(uint32_t rnr) +{ + ARM_MPU_ClrRegionEx(MPU_NS, rnr); +} +#endif + +/** Configure the given MPU region of the given MPU. +* \param mpu Pointer to MPU to be used. +* \param rnr Region number to be configured. +* \param rbar Value for RBAR register. +* \param rlar Value for RLAR register. +*/ +__STATIC_INLINE void ARM_MPU_SetRegionEx(MPU_Type* mpu, uint32_t rnr, uint32_t rbar, uint32_t rlar) +{ + mpu->RNR = rnr; + mpu->RBAR = rbar; + mpu->RLAR = rlar; +} + +/** Configure the given MPU region. +* \param rnr Region number to be configured. +* \param rbar Value for RBAR register. +* \param rlar Value for RLAR register. +*/ +__STATIC_INLINE void ARM_MPU_SetRegion(uint32_t rnr, uint32_t rbar, uint32_t rlar) +{ + ARM_MPU_SetRegionEx(MPU, rnr, rbar, rlar); +} + +#ifdef MPU_NS +/** Configure the given Non-secure MPU region. +* \param rnr Region number to be configured. +* \param rbar Value for RBAR register. +* \param rlar Value for RLAR register. +*/ +__STATIC_INLINE void ARM_MPU_SetRegion_NS(uint32_t rnr, uint32_t rbar, uint32_t rlar) +{ + ARM_MPU_SetRegionEx(MPU_NS, rnr, rbar, rlar); +} +#endif + +/** Memcopy with strictly ordered memory access, e.g. for register targets. +* \param dst Destination data is copied to. +* \param src Source data is copied from. +* \param len Amount of data words to be copied. +*/ +__STATIC_INLINE void orderedCpy(volatile uint32_t* dst, const uint32_t* __RESTRICT src, uint32_t len) +{ + uint32_t i; + + for (i = 0U; i < len; ++i) + { + dst[i] = src[i]; + } +} + +/** Load the given number of MPU regions from a table to the given MPU. +* \param mpu Pointer to the MPU registers to be used. +* \param rnr First region number to be configured. +* \param table Pointer to the MPU configuration table. +* \param cnt Amount of regions to be configured. +*/ +__STATIC_INLINE void ARM_MPU_LoadEx(MPU_Type* mpu, uint32_t rnr, ARM_MPU_Region_t const* table, uint32_t cnt) +{ + const uint32_t rowWordSize = sizeof(ARM_MPU_Region_t) / 4U; + + if (cnt == 1U) + { + mpu->RNR = rnr; + orderedCpy(&(mpu->RBAR), &(table->RBAR), rowWordSize); + } + else + { + uint32_t rnrBase = rnr & ~(MPU_TYPE_RALIASES - 1U); + uint32_t rnrOffset = rnr % MPU_TYPE_RALIASES; + + mpu->RNR = rnrBase; + + while ((rnrOffset + cnt) > MPU_TYPE_RALIASES) + { + uint32_t c = MPU_TYPE_RALIASES - rnrOffset; + orderedCpy(&(mpu->RBAR) + (rnrOffset * 2U), &(table->RBAR), c * rowWordSize); + table += c; + cnt -= c; + rnrOffset = 0U; + rnrBase += MPU_TYPE_RALIASES; + mpu->RNR = rnrBase; + } + + orderedCpy(&(mpu->RBAR) + (rnrOffset * 2U), &(table->RBAR), cnt * rowWordSize); + } +} + +/** Load the given number of MPU regions from a table. +* \param rnr First region number to be configured. +* \param table Pointer to the MPU configuration table. +* \param cnt Amount of regions to be configured. +*/ +__STATIC_INLINE void ARM_MPU_Load(uint32_t rnr, ARM_MPU_Region_t const* table, uint32_t cnt) +{ + ARM_MPU_LoadEx(MPU, rnr, table, cnt); +} + +#ifdef MPU_NS +/** Load the given number of MPU regions from a table to the Non-secure MPU. +* \param rnr First region number to be configured. +* \param table Pointer to the MPU configuration table. +* \param cnt Amount of regions to be configured. +*/ +__STATIC_INLINE void ARM_MPU_Load_NS(uint32_t rnr, ARM_MPU_Region_t const* table, uint32_t cnt) +{ + ARM_MPU_LoadEx(MPU_NS, rnr, table, cnt); +} +#endif + +#endif + diff --git a/EpsilonLights/Drivers/CMSIS/Include/tz_context.h b/EpsilonLights/Drivers/CMSIS/Include/tz_context.h new file mode 100644 index 00000000..50a31e03 --- /dev/null +++ b/EpsilonLights/Drivers/CMSIS/Include/tz_context.h @@ -0,0 +1,70 @@ +/****************************************************************************** + * @file tz_context.h + * @brief Context Management for Armv8-M TrustZone + * @version V1.0.1 + * @date 10. January 2018 + ******************************************************************************/ +/* + * Copyright (c) 2017-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ + +#if defined ( __ICCARM__ ) +#pragma system_include /* treat file as system include file for MISRA check */ +#elif defined (__clang__) +#pragma clang system_header /* treat file as system include file */ +#endif + +#ifndef TZ_CONTEXT_H +#define TZ_CONTEXT_H + +#include + +#ifndef TZ_MODULEID_T +#define TZ_MODULEID_T +/// \details Data type that identifies secure software modules called by a process. +typedef uint32_t TZ_ModuleId_t; +#endif + +/// \details TZ Memory ID identifies an allocated memory slot. +typedef uint32_t TZ_MemoryId_t; + +/// Initialize secure context memory system +/// \return execution status (1: success, 0: error) +uint32_t TZ_InitContextSystem_S (void); + +/// Allocate context memory for calling secure software modules in TrustZone +/// \param[in] module identifies software modules called from non-secure mode +/// \return value != 0 id TrustZone memory slot identifier +/// \return value 0 no memory available or internal error +TZ_MemoryId_t TZ_AllocModuleContext_S (TZ_ModuleId_t module); + +/// Free context memory that was previously allocated with \ref TZ_AllocModuleContext_S +/// \param[in] id TrustZone memory slot identifier +/// \return execution status (1: success, 0: error) +uint32_t TZ_FreeModuleContext_S (TZ_MemoryId_t id); + +/// Load secure context (called on RTOS thread context switch) +/// \param[in] id TrustZone memory slot identifier +/// \return execution status (1: success, 0: error) +uint32_t TZ_LoadContext_S (TZ_MemoryId_t id); + +/// Store secure context (called on RTOS thread context switch) +/// \param[in] id TrustZone memory slot identifier +/// \return execution status (1: success, 0: error) +uint32_t TZ_StoreContext_S (TZ_MemoryId_t id); + +#endif // TZ_CONTEXT_H diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/Legacy/stm32_hal_legacy.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/Legacy/stm32_hal_legacy.h similarity index 81% rename from EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/Legacy/stm32_hal_legacy.h rename to EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/Legacy/stm32_hal_legacy.h index ef24aa48..a92636f5 100644 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/Legacy/stm32_hal_legacy.h +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/Legacy/stm32_hal_legacy.h @@ -2,43 +2,25 @@ ****************************************************************************** * @file stm32_hal_legacy.h * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 * @brief This file contains aliases definition for the STM32Cube HAL constants * macros and functions maintained for legacy purpose. ****************************************************************************** * @attention * - *

© COPYRIGHT(c) 2016 STMicroelectronics

+ *

© Copyright (c) 2019 STMicroelectronics. + * All rights reserved.

* - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause * ****************************************************************************** */ /* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32_HAL_LEGACY -#define __STM32_HAL_LEGACY +#ifndef STM32_HAL_LEGACY +#define STM32_HAL_LEGACY #ifdef __cplusplus extern "C" { @@ -112,6 +94,10 @@ extern "C" { #define HAL_ADC_STATE_ERROR HAL_ADC_STATE_ERROR_INTERNAL #define HAL_ADC_STATE_BUSY HAL_ADC_STATE_BUSY_INTERNAL #define HAL_ADC_STATE_AWD HAL_ADC_STATE_AWD1 + +#if defined(STM32H7) +#define ADC_CHANNEL_VBAT_DIV4 ADC_CHANNEL_VBAT +#endif /* STM32H7 */ /** * @} */ @@ -138,6 +124,9 @@ extern "C" { #define COMP_EXTI_LINE_COMP5_EVENT COMP_EXTI_LINE_COMP5 #define COMP_EXTI_LINE_COMP6_EVENT COMP_EXTI_LINE_COMP6 #define COMP_EXTI_LINE_COMP7_EVENT COMP_EXTI_LINE_COMP7 +#if defined(STM32L0) +#define COMP_LPTIMCONNECTION_ENABLED ((uint32_t)0x00000003U) /*!< COMPX output generic naming: connected to LPTIM input 1 for COMP1, LPTIM input 2 for COMP2 */ +#endif #define COMP_OUTPUT_COMP6TIM2OCREFCLR COMP_OUTPUT_COMP6_TIM2OCREFCLR #if defined(STM32F373xC) || defined(STM32F378xx) #define COMP_OUTPUT_TIM3IC1 COMP_OUTPUT_COMP1_TIM3IC1 @@ -150,6 +139,9 @@ extern "C" { #define COMP_NONINVERTINGINPUT_IO1 COMP_INPUT_PLUS_IO1 #define COMP_NONINVERTINGINPUT_IO2 COMP_INPUT_PLUS_IO2 #define COMP_NONINVERTINGINPUT_IO3 COMP_INPUT_PLUS_IO3 +#define COMP_NONINVERTINGINPUT_IO4 COMP_INPUT_PLUS_IO4 +#define COMP_NONINVERTINGINPUT_IO5 COMP_INPUT_PLUS_IO5 +#define COMP_NONINVERTINGINPUT_IO6 COMP_INPUT_PLUS_IO6 #define COMP_INVERTINGINPUT_1_4VREFINT COMP_INPUT_MINUS_1_4VREFINT #define COMP_INVERTINGINPUT_1_2VREFINT COMP_INPUT_MINUS_1_2VREFINT @@ -160,8 +152,16 @@ extern "C" { #define COMP_INVERTINGINPUT_DAC1 COMP_INPUT_MINUS_DAC1_CH1 #define COMP_INVERTINGINPUT_DAC2 COMP_INPUT_MINUS_DAC1_CH2 #define COMP_INVERTINGINPUT_IO1 COMP_INPUT_MINUS_IO1 +#if defined(STM32L0) +/* Issue fixed on STM32L0 COMP driver: only 2 dedicated IO (IO1 and IO2), */ +/* IO2 was wrongly assigned to IO shared with DAC and IO3 was corresponding */ +/* to the second dedicated IO (only for COMP2). */ +#define COMP_INVERTINGINPUT_IO2 COMP_INPUT_MINUS_DAC1_CH2 +#define COMP_INVERTINGINPUT_IO3 COMP_INPUT_MINUS_IO2 +#else #define COMP_INVERTINGINPUT_IO2 COMP_INPUT_MINUS_IO2 #define COMP_INVERTINGINPUT_IO3 COMP_INPUT_MINUS_IO3 +#endif #define COMP_INVERTINGINPUT_IO4 COMP_INPUT_MINUS_IO4 #define COMP_INVERTINGINPUT_IO5 COMP_INPUT_MINUS_IO5 @@ -229,13 +229,23 @@ extern "C" { #define DAC1_CHANNEL_1 DAC_CHANNEL_1 #define DAC1_CHANNEL_2 DAC_CHANNEL_2 #define DAC2_CHANNEL_1 DAC_CHANNEL_1 -#define DAC_WAVE_NONE ((uint32_t)0x00000000U) -#define DAC_WAVE_NOISE ((uint32_t)DAC_CR_WAVE1_0) -#define DAC_WAVE_TRIANGLE ((uint32_t)DAC_CR_WAVE1_1) +#define DAC_WAVE_NONE 0x00000000U +#define DAC_WAVE_NOISE DAC_CR_WAVE1_0 +#define DAC_WAVE_TRIANGLE DAC_CR_WAVE1_1 #define DAC_WAVEGENERATION_NONE DAC_WAVE_NONE #define DAC_WAVEGENERATION_NOISE DAC_WAVE_NOISE #define DAC_WAVEGENERATION_TRIANGLE DAC_WAVE_TRIANGLE +#if defined(STM32G4) +#define DAC_CHIPCONNECT_DISABLE (DAC_CHIPCONNECT_EXTERNAL | DAC_CHIPCONNECT_BOTH) +#define DAC_CHIPCONNECT_ENABLE (DAC_CHIPCONNECT_INTERNAL | DAC_CHIPCONNECT_BOTH) +#endif + +#if defined(STM32L1) || defined(STM32L4) || defined(STM32G0) +#define HAL_DAC_MSP_INIT_CB_ID HAL_DAC_MSPINIT_CB_ID +#define HAL_DAC_MSP_DEINIT_CB_ID HAL_DAC_MSPDEINIT_CB_ID +#endif + /** * @} */ @@ -253,7 +263,6 @@ extern "C" { #define HAL_REMAPDMA_TIM17_DMA_CH7 DMA_REMAP_TIM17_DMA_CH7 #define HAL_REMAPDMA_SPI2_DMA_CH67 DMA_REMAP_SPI2_DMA_CH67 #define HAL_REMAPDMA_USART2_DMA_CH67 DMA_REMAP_USART2_DMA_CH67 -#define HAL_REMAPDMA_USART3_DMA_CH32 DMA_REMAP_USART3_DMA_CH32 #define HAL_REMAPDMA_I2C1_DMA_CH76 DMA_REMAP_I2C1_DMA_CH76 #define HAL_REMAPDMA_TIM1_DMA_CH6 DMA_REMAP_TIM1_DMA_CH6 #define HAL_REMAPDMA_TIM2_DMA_CH7 DMA_REMAP_TIM2_DMA_CH7 @@ -263,7 +272,100 @@ extern "C" { #define __HAL_REMAPDMA_CHANNEL_ENABLE __HAL_DMA_REMAP_CHANNEL_ENABLE #define __HAL_REMAPDMA_CHANNEL_DISABLE __HAL_DMA_REMAP_CHANNEL_DISABLE +#if defined(STM32L4) +#define HAL_DMAMUX1_REQUEST_GEN_EXTI0 HAL_DMAMUX1_REQ_GEN_EXTI0 +#define HAL_DMAMUX1_REQUEST_GEN_EXTI1 HAL_DMAMUX1_REQ_GEN_EXTI1 +#define HAL_DMAMUX1_REQUEST_GEN_EXTI2 HAL_DMAMUX1_REQ_GEN_EXTI2 +#define HAL_DMAMUX1_REQUEST_GEN_EXTI3 HAL_DMAMUX1_REQ_GEN_EXTI3 +#define HAL_DMAMUX1_REQUEST_GEN_EXTI4 HAL_DMAMUX1_REQ_GEN_EXTI4 +#define HAL_DMAMUX1_REQUEST_GEN_EXTI5 HAL_DMAMUX1_REQ_GEN_EXTI5 +#define HAL_DMAMUX1_REQUEST_GEN_EXTI6 HAL_DMAMUX1_REQ_GEN_EXTI6 +#define HAL_DMAMUX1_REQUEST_GEN_EXTI7 HAL_DMAMUX1_REQ_GEN_EXTI7 +#define HAL_DMAMUX1_REQUEST_GEN_EXTI8 HAL_DMAMUX1_REQ_GEN_EXTI8 +#define HAL_DMAMUX1_REQUEST_GEN_EXTI9 HAL_DMAMUX1_REQ_GEN_EXTI9 +#define HAL_DMAMUX1_REQUEST_GEN_EXTI10 HAL_DMAMUX1_REQ_GEN_EXTI10 +#define HAL_DMAMUX1_REQUEST_GEN_EXTI11 HAL_DMAMUX1_REQ_GEN_EXTI11 +#define HAL_DMAMUX1_REQUEST_GEN_EXTI12 HAL_DMAMUX1_REQ_GEN_EXTI12 +#define HAL_DMAMUX1_REQUEST_GEN_EXTI13 HAL_DMAMUX1_REQ_GEN_EXTI13 +#define HAL_DMAMUX1_REQUEST_GEN_EXTI14 HAL_DMAMUX1_REQ_GEN_EXTI14 +#define HAL_DMAMUX1_REQUEST_GEN_EXTI15 HAL_DMAMUX1_REQ_GEN_EXTI15 +#define HAL_DMAMUX1_REQUEST_GEN_DMAMUX1_CH0_EVT HAL_DMAMUX1_REQ_GEN_DMAMUX1_CH0_EVT +#define HAL_DMAMUX1_REQUEST_GEN_DMAMUX1_CH1_EVT HAL_DMAMUX1_REQ_GEN_DMAMUX1_CH1_EVT +#define HAL_DMAMUX1_REQUEST_GEN_DMAMUX1_CH2_EVT HAL_DMAMUX1_REQ_GEN_DMAMUX1_CH2_EVT +#define HAL_DMAMUX1_REQUEST_GEN_DMAMUX1_CH3_EVT HAL_DMAMUX1_REQ_GEN_DMAMUX1_CH3_EVT +#define HAL_DMAMUX1_REQUEST_GEN_LPTIM1_OUT HAL_DMAMUX1_REQ_GEN_LPTIM1_OUT +#define HAL_DMAMUX1_REQUEST_GEN_LPTIM2_OUT HAL_DMAMUX1_REQ_GEN_LPTIM2_OUT +#define HAL_DMAMUX1_REQUEST_GEN_DSI_TE HAL_DMAMUX1_REQ_GEN_DSI_TE +#define HAL_DMAMUX1_REQUEST_GEN_DSI_EOT HAL_DMAMUX1_REQ_GEN_DSI_EOT +#define HAL_DMAMUX1_REQUEST_GEN_DMA2D_EOT HAL_DMAMUX1_REQ_GEN_DMA2D_EOT +#define HAL_DMAMUX1_REQUEST_GEN_LTDC_IT HAL_DMAMUX1_REQ_GEN_LTDC_IT + +#define HAL_DMAMUX_REQUEST_GEN_NO_EVENT HAL_DMAMUX_REQ_GEN_NO_EVENT +#define HAL_DMAMUX_REQUEST_GEN_RISING HAL_DMAMUX_REQ_GEN_RISING +#define HAL_DMAMUX_REQUEST_GEN_FALLING HAL_DMAMUX_REQ_GEN_FALLING +#define HAL_DMAMUX_REQUEST_GEN_RISING_FALLING HAL_DMAMUX_REQ_GEN_RISING_FALLING + +#endif /* STM32L4 */ + +#if defined(STM32H7) + +#define DMA_REQUEST_DAC1 DMA_REQUEST_DAC1_CH1 +#define DMA_REQUEST_DAC2 DMA_REQUEST_DAC1_CH2 + +#define BDMA_REQUEST_LP_UART1_RX BDMA_REQUEST_LPUART1_RX +#define BDMA_REQUEST_LP_UART1_TX BDMA_REQUEST_LPUART1_TX + +#define HAL_DMAMUX1_REQUEST_GEN_DMAMUX1_CH0_EVT HAL_DMAMUX1_REQ_GEN_DMAMUX1_CH0_EVT +#define HAL_DMAMUX1_REQUEST_GEN_DMAMUX1_CH1_EVT HAL_DMAMUX1_REQ_GEN_DMAMUX1_CH1_EVT +#define HAL_DMAMUX1_REQUEST_GEN_DMAMUX1_CH2_EVT HAL_DMAMUX1_REQ_GEN_DMAMUX1_CH2_EVT +#define HAL_DMAMUX1_REQUEST_GEN_LPTIM1_OUT HAL_DMAMUX1_REQ_GEN_LPTIM1_OUT +#define HAL_DMAMUX1_REQUEST_GEN_LPTIM2_OUT HAL_DMAMUX1_REQ_GEN_LPTIM2_OUT +#define HAL_DMAMUX1_REQUEST_GEN_LPTIM3_OUT HAL_DMAMUX1_REQ_GEN_LPTIM3_OUT +#define HAL_DMAMUX1_REQUEST_GEN_EXTI0 HAL_DMAMUX1_REQ_GEN_EXTI0 +#define HAL_DMAMUX1_REQUEST_GEN_TIM12_TRGO HAL_DMAMUX1_REQ_GEN_TIM12_TRGO + +#define HAL_DMAMUX2_REQUEST_GEN_DMAMUX2_CH0_EVT HAL_DMAMUX2_REQ_GEN_DMAMUX2_CH0_EVT +#define HAL_DMAMUX2_REQUEST_GEN_DMAMUX2_CH1_EVT HAL_DMAMUX2_REQ_GEN_DMAMUX2_CH1_EVT +#define HAL_DMAMUX2_REQUEST_GEN_DMAMUX2_CH2_EVT HAL_DMAMUX2_REQ_GEN_DMAMUX2_CH2_EVT +#define HAL_DMAMUX2_REQUEST_GEN_DMAMUX2_CH3_EVT HAL_DMAMUX2_REQ_GEN_DMAMUX2_CH3_EVT +#define HAL_DMAMUX2_REQUEST_GEN_DMAMUX2_CH4_EVT HAL_DMAMUX2_REQ_GEN_DMAMUX2_CH4_EVT +#define HAL_DMAMUX2_REQUEST_GEN_DMAMUX2_CH5_EVT HAL_DMAMUX2_REQ_GEN_DMAMUX2_CH5_EVT +#define HAL_DMAMUX2_REQUEST_GEN_DMAMUX2_CH6_EVT HAL_DMAMUX2_REQ_GEN_DMAMUX2_CH6_EVT +#define HAL_DMAMUX2_REQUEST_GEN_LPUART1_RX_WKUP HAL_DMAMUX2_REQ_GEN_LPUART1_RX_WKUP +#define HAL_DMAMUX2_REQUEST_GEN_LPUART1_TX_WKUP HAL_DMAMUX2_REQ_GEN_LPUART1_TX_WKUP +#define HAL_DMAMUX2_REQUEST_GEN_LPTIM2_WKUP HAL_DMAMUX2_REQ_GEN_LPTIM2_WKUP +#define HAL_DMAMUX2_REQUEST_GEN_LPTIM2_OUT HAL_DMAMUX2_REQ_GEN_LPTIM2_OUT +#define HAL_DMAMUX2_REQUEST_GEN_LPTIM3_WKUP HAL_DMAMUX2_REQ_GEN_LPTIM3_WKUP +#define HAL_DMAMUX2_REQUEST_GEN_LPTIM3_OUT HAL_DMAMUX2_REQ_GEN_LPTIM3_OUT +#define HAL_DMAMUX2_REQUEST_GEN_LPTIM4_WKUP HAL_DMAMUX2_REQ_GEN_LPTIM4_WKUP +#define HAL_DMAMUX2_REQUEST_GEN_LPTIM5_WKUP HAL_DMAMUX2_REQ_GEN_LPTIM5_WKUP +#define HAL_DMAMUX2_REQUEST_GEN_I2C4_WKUP HAL_DMAMUX2_REQ_GEN_I2C4_WKUP +#define HAL_DMAMUX2_REQUEST_GEN_SPI6_WKUP HAL_DMAMUX2_REQ_GEN_SPI6_WKUP +#define HAL_DMAMUX2_REQUEST_GEN_COMP1_OUT HAL_DMAMUX2_REQ_GEN_COMP1_OUT +#define HAL_DMAMUX2_REQUEST_GEN_COMP2_OUT HAL_DMAMUX2_REQ_GEN_COMP2_OUT +#define HAL_DMAMUX2_REQUEST_GEN_RTC_WKUP HAL_DMAMUX2_REQ_GEN_RTC_WKUP +#define HAL_DMAMUX2_REQUEST_GEN_EXTI0 HAL_DMAMUX2_REQ_GEN_EXTI0 +#define HAL_DMAMUX2_REQUEST_GEN_EXTI2 HAL_DMAMUX2_REQ_GEN_EXTI2 +#define HAL_DMAMUX2_REQUEST_GEN_I2C4_IT_EVT HAL_DMAMUX2_REQ_GEN_I2C4_IT_EVT +#define HAL_DMAMUX2_REQUEST_GEN_SPI6_IT HAL_DMAMUX2_REQ_GEN_SPI6_IT +#define HAL_DMAMUX2_REQUEST_GEN_LPUART1_TX_IT HAL_DMAMUX2_REQ_GEN_LPUART1_TX_IT +#define HAL_DMAMUX2_REQUEST_GEN_LPUART1_RX_IT HAL_DMAMUX2_REQ_GEN_LPUART1_RX_IT +#define HAL_DMAMUX2_REQUEST_GEN_ADC3_IT HAL_DMAMUX2_REQ_GEN_ADC3_IT +#define HAL_DMAMUX2_REQUEST_GEN_ADC3_AWD1_OUT HAL_DMAMUX2_REQ_GEN_ADC3_AWD1_OUT +#define HAL_DMAMUX2_REQUEST_GEN_BDMA_CH0_IT HAL_DMAMUX2_REQ_GEN_BDMA_CH0_IT +#define HAL_DMAMUX2_REQUEST_GEN_BDMA_CH1_IT HAL_DMAMUX2_REQ_GEN_BDMA_CH1_IT + +#define HAL_DMAMUX_REQUEST_GEN_NO_EVENT HAL_DMAMUX_REQ_GEN_NO_EVENT +#define HAL_DMAMUX_REQUEST_GEN_RISING HAL_DMAMUX_REQ_GEN_RISING +#define HAL_DMAMUX_REQUEST_GEN_FALLING HAL_DMAMUX_REQ_GEN_FALLING +#define HAL_DMAMUX_REQUEST_GEN_RISING_FALLING HAL_DMAMUX_REQ_GEN_RISING_FALLING + +#define DFSDM_FILTER_EXT_TRIG_LPTIM1 DFSDM_FILTER_EXT_TRIG_LPTIM1_OUT +#define DFSDM_FILTER_EXT_TRIG_LPTIM2 DFSDM_FILTER_EXT_TRIG_LPTIM2_OUT +#define DFSDM_FILTER_EXT_TRIG_LPTIM3 DFSDM_FILTER_EXT_TRIG_LPTIM3_OUT + +#endif /* STM32H7 */ /** * @} @@ -344,6 +446,39 @@ extern "C" { #define OB_RDP_LEVEL0 OB_RDP_LEVEL_0 #define OB_RDP_LEVEL1 OB_RDP_LEVEL_1 #define OB_RDP_LEVEL2 OB_RDP_LEVEL_2 +#if defined(STM32G0) +#define OB_BOOT_LOCK_DISABLE OB_BOOT_ENTRY_FORCED_NONE +#define OB_BOOT_LOCK_ENABLE OB_BOOT_ENTRY_FORCED_FLASH +#else +#define OB_BOOT_ENTRY_FORCED_NONE OB_BOOT_LOCK_DISABLE +#define OB_BOOT_ENTRY_FORCED_FLASH OB_BOOT_LOCK_ENABLE +#endif +#if defined(STM32H7) +#define FLASH_FLAG_SNECCE_BANK1RR FLASH_FLAG_SNECCERR_BANK1 +#define FLASH_FLAG_DBECCE_BANK1RR FLASH_FLAG_DBECCERR_BANK1 +#define FLASH_FLAG_STRBER_BANK1R FLASH_FLAG_STRBERR_BANK1 +#define FLASH_FLAG_SNECCE_BANK2RR FLASH_FLAG_SNECCERR_BANK2 +#define FLASH_FLAG_DBECCE_BANK2RR FLASH_FLAG_DBECCERR_BANK2 +#define FLASH_FLAG_STRBER_BANK2R FLASH_FLAG_STRBERR_BANK2 +#endif + +/** + * @} + */ + +/** @defgroup HAL_JPEG_Aliased_Macros HAL JPEG Aliased Macros maintained for legacy purpose + * @{ + */ + +#if defined(STM32H7) +#define __HAL_RCC_JPEG_CLK_ENABLE __HAL_RCC_JPGDECEN_CLK_ENABLE +#define __HAL_RCC_JPEG_CLK_DISABLE __HAL_RCC_JPGDECEN_CLK_DISABLE +#define __HAL_RCC_JPEG_FORCE_RESET __HAL_RCC_JPGDECRST_FORCE_RESET +#define __HAL_RCC_JPEG_RELEASE_RESET __HAL_RCC_JPGDECRST_RELEASE_RESET +#define __HAL_RCC_JPEG_CLK_SLEEP_ENABLE __HAL_RCC_JPGDEC_CLK_SLEEP_ENABLE +#define __HAL_RCC_JPEG_CLK_SLEEP_DISABLE __HAL_RCC_JPGDEC_CLK_SLEEP_DISABLE +#endif /* STM32H7 */ + /** * @} */ @@ -361,6 +496,13 @@ extern "C" { #define HAL_SYSCFG_FASTMODEPLUS_I2C1 I2C_FASTMODEPLUS_I2C1 #define HAL_SYSCFG_FASTMODEPLUS_I2C2 I2C_FASTMODEPLUS_I2C2 #define HAL_SYSCFG_FASTMODEPLUS_I2C3 I2C_FASTMODEPLUS_I2C3 +#if defined(STM32G4) + +#define HAL_SYSCFG_EnableIOAnalogSwitchBooster HAL_SYSCFG_EnableIOSwitchBooster +#define HAL_SYSCFG_DisableIOAnalogSwitchBooster HAL_SYSCFG_DisableIOSwitchBooster +#define HAL_SYSCFG_EnableIOAnalogSwitchVDD HAL_SYSCFG_EnableIOSwitchVDD +#define HAL_SYSCFG_DisableIOAnalogSwitchVDD HAL_SYSCFG_DisableIOSwitchVDD +#endif /* STM32G4 */ /** * @} */ @@ -369,12 +511,12 @@ extern "C" { /** @defgroup LL_FMC_Aliased_Defines LL FMC Aliased Defines maintained for compatibility purpose * @{ */ -#if defined(STM32L4) || defined(STM32F7) +#if defined(STM32L4) || defined(STM32F7) || defined(STM32H7) || defined(STM32G4) #define FMC_NAND_PCC_WAIT_FEATURE_DISABLE FMC_NAND_WAIT_FEATURE_DISABLE #define FMC_NAND_PCC_WAIT_FEATURE_ENABLE FMC_NAND_WAIT_FEATURE_ENABLE #define FMC_NAND_PCC_MEM_BUS_WIDTH_8 FMC_NAND_MEM_BUS_WIDTH_8 #define FMC_NAND_PCC_MEM_BUS_WIDTH_16 FMC_NAND_MEM_BUS_WIDTH_16 -#else +#elif defined(STM32F1) || defined(STM32F2) || defined(STM32F3) || defined(STM32F4) #define FMC_NAND_WAIT_FEATURE_DISABLE FMC_NAND_PCC_WAIT_FEATURE_DISABLE #define FMC_NAND_WAIT_FEATURE_ENABLE FMC_NAND_PCC_WAIT_FEATURE_ENABLE #define FMC_NAND_MEM_BUS_WIDTH_8 FMC_NAND_PCC_MEM_BUS_WIDTH_8 @@ -415,16 +557,25 @@ extern "C" { #define GPIO_AF12_SDMMC GPIO_AF12_SDMMC1 #endif +#if defined(STM32H7) +#define GPIO_AF7_SDIO1 GPIO_AF7_SDMMC1 +#define GPIO_AF8_SDIO1 GPIO_AF8_SDMMC1 +#define GPIO_AF12_SDIO1 GPIO_AF12_SDMMC1 +#define GPIO_AF9_SDIO2 GPIO_AF9_SDMMC2 +#define GPIO_AF10_SDIO2 GPIO_AF10_SDMMC2 +#define GPIO_AF11_SDIO2 GPIO_AF11_SDMMC2 +#endif + #define GPIO_AF0_LPTIM GPIO_AF0_LPTIM1 #define GPIO_AF1_LPTIM GPIO_AF1_LPTIM1 #define GPIO_AF2_LPTIM GPIO_AF2_LPTIM1 -#if defined(STM32L0) || defined(STM32L4) || defined(STM32F4) || defined(STM32F2) || defined(STM32F7) +#if defined(STM32L0) || defined(STM32L4) || defined(STM32F4) || defined(STM32F2) || defined(STM32F7) || defined(STM32G4) || defined(STM32H7) #define GPIO_SPEED_LOW GPIO_SPEED_FREQ_LOW #define GPIO_SPEED_MEDIUM GPIO_SPEED_FREQ_MEDIUM #define GPIO_SPEED_FAST GPIO_SPEED_FREQ_HIGH #define GPIO_SPEED_HIGH GPIO_SPEED_FREQ_VERY_HIGH -#endif /* STM32L0 || STM32L4 || STM32F4 || STM32F2 || STM32F7 */ +#endif /* STM32L0 || STM32L4 || STM32F4 || STM32F2 || STM32F7 || STM32G4 || STM32H7*/ #if defined(STM32L1) #define GPIO_SPEED_VERY_LOW GPIO_SPEED_FREQ_LOW @@ -465,6 +616,125 @@ extern "C" { #define __HAL_HRTIM_GetClockPrescaler __HAL_HRTIM_GETCLOCKPRESCALER #define __HAL_HRTIM_SetCompare __HAL_HRTIM_SETCOMPARE #define __HAL_HRTIM_GetCompare __HAL_HRTIM_GETCOMPARE + +#if defined(STM32G4) +#define HAL_HRTIM_ExternalEventCounterConfig HAL_HRTIM_ExtEventCounterConfig +#define HAL_HRTIM_ExternalEventCounterEnable HAL_HRTIM_ExtEventCounterEnable +#define HAL_HRTIM_ExternalEventCounterDisable HAL_HRTIM_ExtEventCounterDisable +#define HAL_HRTIM_ExternalEventCounterReset HAL_HRTIM_ExtEventCounterReset +#endif /* STM32G4 */ + +#if defined(STM32H7) +#define HRTIM_OUTPUTSET_TIMAEV1_TIMBCMP1 HRTIM_OUTPUTSET_TIMEV_1 +#define HRTIM_OUTPUTSET_TIMAEV2_TIMBCMP2 HRTIM_OUTPUTSET_TIMEV_2 +#define HRTIM_OUTPUTSET_TIMAEV3_TIMCCMP2 HRTIM_OUTPUTSET_TIMEV_3 +#define HRTIM_OUTPUTSET_TIMAEV4_TIMCCMP3 HRTIM_OUTPUTSET_TIMEV_4 +#define HRTIM_OUTPUTSET_TIMAEV5_TIMDCMP1 HRTIM_OUTPUTSET_TIMEV_5 +#define HRTIM_OUTPUTSET_TIMAEV6_TIMDCMP2 HRTIM_OUTPUTSET_TIMEV_6 +#define HRTIM_OUTPUTSET_TIMAEV7_TIMECMP3 HRTIM_OUTPUTSET_TIMEV_7 +#define HRTIM_OUTPUTSET_TIMAEV8_TIMECMP4 HRTIM_OUTPUTSET_TIMEV_8 +#define HRTIM_OUTPUTSET_TIMAEV9_TIMFCMP4 HRTIM_OUTPUTSET_TIMEV_9 +#define HRTIM_OUTPUTSET_TIMBEV1_TIMACMP1 HRTIM_OUTPUTSET_TIMEV_1 +#define HRTIM_OUTPUTSET_TIMBEV2_TIMACMP2 HRTIM_OUTPUTSET_TIMEV_2 +#define HRTIM_OUTPUTSET_TIMBEV3_TIMCCMP3 HRTIM_OUTPUTSET_TIMEV_3 +#define HRTIM_OUTPUTSET_TIMBEV4_TIMCCMP4 HRTIM_OUTPUTSET_TIMEV_4 +#define HRTIM_OUTPUTSET_TIMBEV5_TIMDCMP3 HRTIM_OUTPUTSET_TIMEV_5 +#define HRTIM_OUTPUTSET_TIMBEV6_TIMDCMP4 HRTIM_OUTPUTSET_TIMEV_6 +#define HRTIM_OUTPUTSET_TIMBEV7_TIMECMP1 HRTIM_OUTPUTSET_TIMEV_7 +#define HRTIM_OUTPUTSET_TIMBEV8_TIMECMP2 HRTIM_OUTPUTSET_TIMEV_8 +#define HRTIM_OUTPUTSET_TIMBEV9_TIMFCMP3 HRTIM_OUTPUTSET_TIMEV_9 +#define HRTIM_OUTPUTSET_TIMCEV1_TIMACMP1 HRTIM_OUTPUTSET_TIMEV_1 +#define HRTIM_OUTPUTSET_TIMCEV2_TIMACMP2 HRTIM_OUTPUTSET_TIMEV_2 +#define HRTIM_OUTPUTSET_TIMCEV3_TIMBCMP2 HRTIM_OUTPUTSET_TIMEV_3 +#define HRTIM_OUTPUTSET_TIMCEV4_TIMBCMP3 HRTIM_OUTPUTSET_TIMEV_4 +#define HRTIM_OUTPUTSET_TIMCEV5_TIMDCMP2 HRTIM_OUTPUTSET_TIMEV_5 +#define HRTIM_OUTPUTSET_TIMCEV6_TIMDCMP4 HRTIM_OUTPUTSET_TIMEV_6 +#define HRTIM_OUTPUTSET_TIMCEV7_TIMECMP3 HRTIM_OUTPUTSET_TIMEV_7 +#define HRTIM_OUTPUTSET_TIMCEV8_TIMECMP4 HRTIM_OUTPUTSET_TIMEV_8 +#define HRTIM_OUTPUTSET_TIMCEV9_TIMFCMP2 HRTIM_OUTPUTSET_TIMEV_9 +#define HRTIM_OUTPUTSET_TIMDEV1_TIMACMP1 HRTIM_OUTPUTSET_TIMEV_1 +#define HRTIM_OUTPUTSET_TIMDEV2_TIMACMP4 HRTIM_OUTPUTSET_TIMEV_2 +#define HRTIM_OUTPUTSET_TIMDEV3_TIMBCMP2 HRTIM_OUTPUTSET_TIMEV_3 +#define HRTIM_OUTPUTSET_TIMDEV4_TIMBCMP4 HRTIM_OUTPUTSET_TIMEV_4 +#define HRTIM_OUTPUTSET_TIMDEV5_TIMCCMP4 HRTIM_OUTPUTSET_TIMEV_5 +#define HRTIM_OUTPUTSET_TIMDEV6_TIMECMP1 HRTIM_OUTPUTSET_TIMEV_6 +#define HRTIM_OUTPUTSET_TIMDEV7_TIMECMP4 HRTIM_OUTPUTSET_TIMEV_7 +#define HRTIM_OUTPUTSET_TIMDEV8_TIMFCMP1 HRTIM_OUTPUTSET_TIMEV_8 +#define HRTIM_OUTPUTSET_TIMDEV9_TIMFCMP3 HRTIM_OUTPUTSET_TIMEV_9 +#define HRTIM_OUTPUTSET_TIMEEV1_TIMACMP4 HRTIM_OUTPUTSET_TIMEV_1 +#define HRTIM_OUTPUTSET_TIMEEV2_TIMBCMP3 HRTIM_OUTPUTSET_TIMEV_2 +#define HRTIM_OUTPUTSET_TIMEEV3_TIMBCMP4 HRTIM_OUTPUTSET_TIMEV_3 +#define HRTIM_OUTPUTSET_TIMEEV4_TIMCCMP1 HRTIM_OUTPUTSET_TIMEV_4 +#define HRTIM_OUTPUTSET_TIMEEV5_TIMDCMP2 HRTIM_OUTPUTSET_TIMEV_5 +#define HRTIM_OUTPUTSET_TIMEEV6_TIMDCMP1 HRTIM_OUTPUTSET_TIMEV_6 +#define HRTIM_OUTPUTSET_TIMEEV7_TIMDCMP2 HRTIM_OUTPUTSET_TIMEV_7 +#define HRTIM_OUTPUTSET_TIMEEV8_TIMFCMP3 HRTIM_OUTPUTSET_TIMEV_8 +#define HRTIM_OUTPUTSET_TIMEEV9_TIMFCMP4 HRTIM_OUTPUTSET_TIMEV_9 +#define HRTIM_OUTPUTSET_TIMFEV1_TIMACMP3 HRTIM_OUTPUTSET_TIMEV_1 +#define HRTIM_OUTPUTSET_TIMFEV2_TIMBCMP1 HRTIM_OUTPUTSET_TIMEV_2 +#define HRTIM_OUTPUTSET_TIMFEV3_TIMBCMP4 HRTIM_OUTPUTSET_TIMEV_3 +#define HRTIM_OUTPUTSET_TIMFEV4_TIMCCMP1 HRTIM_OUTPUTSET_TIMEV_4 +#define HRTIM_OUTPUTSET_TIMFEV5_TIMCCMP4 HRTIM_OUTPUTSET_TIMEV_5 +#define HRTIM_OUTPUTSET_TIMFEV6_TIMDCMP3 HRTIM_OUTPUTSET_TIMEV_6 +#define HRTIM_OUTPUTSET_TIMFEV7_TIMDCMP4 HRTIM_OUTPUTSET_TIMEV_7 +#define HRTIM_OUTPUTSET_TIMFEV8_TIMECMP2 HRTIM_OUTPUTSET_TIMEV_8 +#define HRTIM_OUTPUTSET_TIMFEV9_TIMECMP3 HRTIM_OUTPUTSET_TIMEV_9 + +#define HRTIM_OUTPUTRESET_TIMAEV1_TIMBCMP1 HRTIM_OUTPUTSET_TIMEV_1 +#define HRTIM_OUTPUTRESET_TIMAEV2_TIMBCMP2 HRTIM_OUTPUTSET_TIMEV_2 +#define HRTIM_OUTPUTRESET_TIMAEV3_TIMCCMP2 HRTIM_OUTPUTSET_TIMEV_3 +#define HRTIM_OUTPUTRESET_TIMAEV4_TIMCCMP3 HRTIM_OUTPUTSET_TIMEV_4 +#define HRTIM_OUTPUTRESET_TIMAEV5_TIMDCMP1 HRTIM_OUTPUTSET_TIMEV_5 +#define HRTIM_OUTPUTRESET_TIMAEV6_TIMDCMP2 HRTIM_OUTPUTSET_TIMEV_6 +#define HRTIM_OUTPUTRESET_TIMAEV7_TIMECMP3 HRTIM_OUTPUTSET_TIMEV_7 +#define HRTIM_OUTPUTRESET_TIMAEV8_TIMECMP4 HRTIM_OUTPUTSET_TIMEV_8 +#define HRTIM_OUTPUTRESET_TIMAEV9_TIMFCMP4 HRTIM_OUTPUTSET_TIMEV_9 +#define HRTIM_OUTPUTRESET_TIMBEV1_TIMACMP1 HRTIM_OUTPUTSET_TIMEV_1 +#define HRTIM_OUTPUTRESET_TIMBEV2_TIMACMP2 HRTIM_OUTPUTSET_TIMEV_2 +#define HRTIM_OUTPUTRESET_TIMBEV3_TIMCCMP3 HRTIM_OUTPUTSET_TIMEV_3 +#define HRTIM_OUTPUTRESET_TIMBEV4_TIMCCMP4 HRTIM_OUTPUTSET_TIMEV_4 +#define HRTIM_OUTPUTRESET_TIMBEV5_TIMDCMP3 HRTIM_OUTPUTSET_TIMEV_5 +#define HRTIM_OUTPUTRESET_TIMBEV6_TIMDCMP4 HRTIM_OUTPUTSET_TIMEV_6 +#define HRTIM_OUTPUTRESET_TIMBEV7_TIMECMP1 HRTIM_OUTPUTSET_TIMEV_7 +#define HRTIM_OUTPUTRESET_TIMBEV8_TIMECMP2 HRTIM_OUTPUTSET_TIMEV_8 +#define HRTIM_OUTPUTRESET_TIMBEV9_TIMFCMP3 HRTIM_OUTPUTSET_TIMEV_9 +#define HRTIM_OUTPUTRESET_TIMCEV1_TIMACMP1 HRTIM_OUTPUTSET_TIMEV_1 +#define HRTIM_OUTPUTRESET_TIMCEV2_TIMACMP2 HRTIM_OUTPUTSET_TIMEV_2 +#define HRTIM_OUTPUTRESET_TIMCEV3_TIMBCMP2 HRTIM_OUTPUTSET_TIMEV_3 +#define HRTIM_OUTPUTRESET_TIMCEV4_TIMBCMP3 HRTIM_OUTPUTSET_TIMEV_4 +#define HRTIM_OUTPUTRESET_TIMCEV5_TIMDCMP2 HRTIM_OUTPUTSET_TIMEV_5 +#define HRTIM_OUTPUTRESET_TIMCEV6_TIMDCMP4 HRTIM_OUTPUTSET_TIMEV_6 +#define HRTIM_OUTPUTRESET_TIMCEV7_TIMECMP3 HRTIM_OUTPUTSET_TIMEV_7 +#define HRTIM_OUTPUTRESET_TIMCEV8_TIMECMP4 HRTIM_OUTPUTSET_TIMEV_8 +#define HRTIM_OUTPUTRESET_TIMCEV9_TIMFCMP2 HRTIM_OUTPUTSET_TIMEV_9 +#define HRTIM_OUTPUTRESET_TIMDEV1_TIMACMP1 HRTIM_OUTPUTSET_TIMEV_1 +#define HRTIM_OUTPUTRESET_TIMDEV2_TIMACMP4 HRTIM_OUTPUTSET_TIMEV_2 +#define HRTIM_OUTPUTRESET_TIMDEV3_TIMBCMP2 HRTIM_OUTPUTSET_TIMEV_3 +#define HRTIM_OUTPUTRESET_TIMDEV4_TIMBCMP4 HRTIM_OUTPUTSET_TIMEV_4 +#define HRTIM_OUTPUTRESET_TIMDEV5_TIMCCMP4 HRTIM_OUTPUTSET_TIMEV_5 +#define HRTIM_OUTPUTRESET_TIMDEV6_TIMECMP1 HRTIM_OUTPUTSET_TIMEV_6 +#define HRTIM_OUTPUTRESET_TIMDEV7_TIMECMP4 HRTIM_OUTPUTSET_TIMEV_7 +#define HRTIM_OUTPUTRESET_TIMDEV8_TIMFCMP1 HRTIM_OUTPUTSET_TIMEV_8 +#define HRTIM_OUTPUTRESET_TIMDEV9_TIMFCMP3 HRTIM_OUTPUTSET_TIMEV_9 +#define HRTIM_OUTPUTRESET_TIMEEV1_TIMACMP4 HRTIM_OUTPUTSET_TIMEV_1 +#define HRTIM_OUTPUTRESET_TIMEEV2_TIMBCMP3 HRTIM_OUTPUTSET_TIMEV_2 +#define HRTIM_OUTPUTRESET_TIMEEV3_TIMBCMP4 HRTIM_OUTPUTSET_TIMEV_3 +#define HRTIM_OUTPUTRESET_TIMEEV4_TIMCCMP1 HRTIM_OUTPUTSET_TIMEV_4 +#define HRTIM_OUTPUTRESET_TIMEEV5_TIMDCMP2 HRTIM_OUTPUTSET_TIMEV_5 +#define HRTIM_OUTPUTRESET_TIMEEV6_TIMDCMP1 HRTIM_OUTPUTSET_TIMEV_6 +#define HRTIM_OUTPUTRESET_TIMEEV7_TIMDCMP2 HRTIM_OUTPUTSET_TIMEV_7 +#define HRTIM_OUTPUTRESET_TIMEEV8_TIMFCMP3 HRTIM_OUTPUTSET_TIMEV_8 +#define HRTIM_OUTPUTRESET_TIMEEV9_TIMFCMP4 HRTIM_OUTPUTSET_TIMEV_9 +#define HRTIM_OUTPUTRESET_TIMFEV1_TIMACMP3 HRTIM_OUTPUTSET_TIMEV_1 +#define HRTIM_OUTPUTRESET_TIMFEV2_TIMBCMP1 HRTIM_OUTPUTSET_TIMEV_2 +#define HRTIM_OUTPUTRESET_TIMFEV3_TIMBCMP4 HRTIM_OUTPUTSET_TIMEV_3 +#define HRTIM_OUTPUTRESET_TIMFEV4_TIMCCMP1 HRTIM_OUTPUTSET_TIMEV_4 +#define HRTIM_OUTPUTRESET_TIMFEV5_TIMCCMP4 HRTIM_OUTPUTSET_TIMEV_5 +#define HRTIM_OUTPUTRESET_TIMFEV6_TIMDCMP3 HRTIM_OUTPUTSET_TIMEV_6 +#define HRTIM_OUTPUTRESET_TIMFEV7_TIMDCMP4 HRTIM_OUTPUTSET_TIMEV_7 +#define HRTIM_OUTPUTRESET_TIMFEV8_TIMECMP2 HRTIM_OUTPUTSET_TIMEV_8 +#define HRTIM_OUTPUTRESET_TIMFEV9_TIMECMP3 HRTIM_OUTPUTSET_TIMEV_9 +#endif /* STM32H7 */ /** * @} */ @@ -604,6 +874,12 @@ extern "C" { #define OPAMP_PGACONNECT_VM0 OPAMP_PGA_CONNECT_INVERTINGINPUT_IO0 #define OPAMP_PGACONNECT_VM1 OPAMP_PGA_CONNECT_INVERTINGINPUT_IO1 +#if defined(STM32L1) || defined(STM32L4) +#define HAL_OPAMP_MSP_INIT_CB_ID HAL_OPAMP_MSPINIT_CB_ID +#define HAL_OPAMP_MSP_DEINIT_CB_ID HAL_OPAMP_MSPDEINIT_CB_ID +#endif + + /** * @} */ @@ -612,6 +888,15 @@ extern "C" { * @{ */ #define I2S_STANDARD_PHILLIPS I2S_STANDARD_PHILIPS + +#if defined(STM32H7) +#define I2S_IT_TXE I2S_IT_TXP +#define I2S_IT_RXNE I2S_IT_RXP + +#define I2S_FLAG_TXE I2S_FLAG_TXP +#define I2S_FLAG_RXNE I2S_FLAG_RXP +#endif + #if defined(STM32F7) #define I2S_CLOCK_SYSCLK I2S_CLOCK_PLL #endif @@ -657,7 +942,6 @@ extern "C" { #define FORMAT_BCD RTC_FORMAT_BCD #define RTC_ALARMSUBSECONDMASK_None RTC_ALARMSUBSECONDMASK_NONE -#define RTC_TAMPERERASEBACKUP_ENABLED RTC_TAMPER_ERASE_BACKUP_ENABLE #define RTC_TAMPERERASEBACKUP_DISABLED RTC_TAMPER_ERASE_BACKUP_DISABLE #define RTC_TAMPERMASK_FLAG_DISABLED RTC_TAMPERMASK_FLAG_DISABLE #define RTC_TAMPERMASK_FLAG_ENABLED RTC_TAMPERMASK_FLAG_ENABLE @@ -665,9 +949,6 @@ extern "C" { #define RTC_MASKTAMPERFLAG_DISABLED RTC_TAMPERMASK_FLAG_DISABLE #define RTC_MASKTAMPERFLAG_ENABLED RTC_TAMPERMASK_FLAG_ENABLE #define RTC_TAMPERERASEBACKUP_ENABLED RTC_TAMPER_ERASE_BACKUP_ENABLE -#define RTC_TAMPERERASEBACKUP_DISABLED RTC_TAMPER_ERASE_BACKUP_DISABLE -#define RTC_MASKTAMPERFLAG_DISABLED RTC_TAMPERMASK_FLAG_DISABLE -#define RTC_MASKTAMPERFLAG_ENABLED RTC_TAMPERMASK_FLAG_ENABLE #define RTC_TAMPER1_2_INTERRUPT RTC_ALL_TAMPER_INTERRUPT #define RTC_TAMPER1_2_3_INTERRUPT RTC_ALL_TAMPER_INTERRUPT @@ -740,6 +1021,21 @@ extern "C" { #define SPI_NSS_PULSE_DISABLED SPI_NSS_PULSE_DISABLE #define SPI_NSS_PULSE_ENABLED SPI_NSS_PULSE_ENABLE +#if defined(STM32H7) + +#define SPI_FLAG_TXE SPI_FLAG_TXP +#define SPI_FLAG_RXNE SPI_FLAG_RXP + +#define SPI_IT_TXE SPI_IT_TXP +#define SPI_IT_RXNE SPI_IT_RXP + +#define SPI_FRLVL_EMPTY SPI_RX_FIFO_0PACKET +#define SPI_FRLVL_QUARTER_FULL SPI_RX_FIFO_1PACKET +#define SPI_FRLVL_HALF_FULL SPI_RX_FIFO_2PACKET +#define SPI_FRLVL_FULL SPI_RX_FIFO_3PACKET + +#endif /* STM32H7 */ + /** * @} */ @@ -807,6 +1103,33 @@ extern "C" { #define TIM_DMABurstLength_17Transfers TIM_DMABURSTLENGTH_17TRANSFERS #define TIM_DMABurstLength_18Transfers TIM_DMABURSTLENGTH_18TRANSFERS +#if defined(STM32L0) +#define TIM22_TI1_GPIO1 TIM22_TI1_GPIO +#define TIM22_TI1_GPIO2 TIM22_TI1_GPIO +#endif + +#if defined(STM32F3) +#define IS_TIM_HALL_INTERFACE_INSTANCE IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE +#endif + +#if defined(STM32H7) +#define TIM_TIM1_ETR_COMP1_OUT TIM_TIM1_ETR_COMP1 +#define TIM_TIM1_ETR_COMP2_OUT TIM_TIM1_ETR_COMP2 +#define TIM_TIM8_ETR_COMP1_OUT TIM_TIM8_ETR_COMP1 +#define TIM_TIM8_ETR_COMP2_OUT TIM_TIM8_ETR_COMP2 +#define TIM_TIM2_ETR_COMP1_OUT TIM_TIM2_ETR_COMP1 +#define TIM_TIM2_ETR_COMP2_OUT TIM_TIM2_ETR_COMP2 +#define TIM_TIM3_ETR_COMP1_OUT TIM_TIM3_ETR_COMP1 +#define TIM_TIM1_TI1_COMP1_OUT TIM_TIM1_TI1_COMP1 +#define TIM_TIM8_TI1_COMP2_OUT TIM_TIM8_TI1_COMP2 +#define TIM_TIM2_TI4_COMP1_OUT TIM_TIM2_TI4_COMP1 +#define TIM_TIM2_TI4_COMP2_OUT TIM_TIM2_TI4_COMP2 +#define TIM_TIM2_TI4_COMP1COMP2_OUT TIM_TIM2_TI4_COMP1_COMP2 +#define TIM_TIM3_TI1_COMP1_OUT TIM_TIM3_TI1_COMP1 +#define TIM_TIM3_TI1_COMP2_OUT TIM_TIM3_TI1_COMP2 +#define TIM_TIM3_TI1_COMP1COMP2_OUT TIM_TIM3_TI1_COMP1_COMP2 +#endif + /** * @} */ @@ -841,6 +1164,8 @@ extern "C" { #define __DIVFRAQ_SAMPLING8 UART_DIVFRAQ_SAMPLING8 #define __UART_BRR_SAMPLING8 UART_BRR_SAMPLING8 +#define __DIV_LPUART UART_DIV_LPUART + #define UART_WAKEUPMETHODE_IDLELINE UART_WAKEUPMETHOD_IDLELINE #define UART_WAKEUPMETHODE_ADDRESSMARK UART_WAKEUPMETHOD_ADDRESSMARK @@ -902,48 +1227,48 @@ extern "C" { #define MACFCR_CLEAR_MASK ETH_MACFCR_CLEAR_MASK #define DMAOMR_CLEAR_MASK ETH_DMAOMR_CLEAR_MASK -#define ETH_MMCCR ((uint32_t)0x00000100U) -#define ETH_MMCRIR ((uint32_t)0x00000104U) -#define ETH_MMCTIR ((uint32_t)0x00000108U) -#define ETH_MMCRIMR ((uint32_t)0x0000010CU) -#define ETH_MMCTIMR ((uint32_t)0x00000110U) -#define ETH_MMCTGFSCCR ((uint32_t)0x0000014CU) -#define ETH_MMCTGFMSCCR ((uint32_t)0x00000150U) -#define ETH_MMCTGFCR ((uint32_t)0x00000168U) -#define ETH_MMCRFCECR ((uint32_t)0x00000194U) -#define ETH_MMCRFAECR ((uint32_t)0x00000198U) -#define ETH_MMCRGUFCR ((uint32_t)0x000001C4U) - -#define ETH_MAC_TXFIFO_FULL ((uint32_t)0x02000000) /* Tx FIFO full */ -#define ETH_MAC_TXFIFONOT_EMPTY ((uint32_t)0x01000000) /* Tx FIFO not empty */ -#define ETH_MAC_TXFIFO_WRITE_ACTIVE ((uint32_t)0x00400000) /* Tx FIFO write active */ -#define ETH_MAC_TXFIFO_IDLE ((uint32_t)0x00000000) /* Tx FIFO read status: Idle */ -#define ETH_MAC_TXFIFO_READ ((uint32_t)0x00100000) /* Tx FIFO read status: Read (transferring data to the MAC transmitter) */ -#define ETH_MAC_TXFIFO_WAITING ((uint32_t)0x00200000) /* Tx FIFO read status: Waiting for TxStatus from MAC transmitter */ -#define ETH_MAC_TXFIFO_WRITING ((uint32_t)0x00300000) /* Tx FIFO read status: Writing the received TxStatus or flushing the TxFIFO */ -#define ETH_MAC_TRANSMISSION_PAUSE ((uint32_t)0x00080000) /* MAC transmitter in pause */ -#define ETH_MAC_TRANSMITFRAMECONTROLLER_IDLE ((uint32_t)0x00000000) /* MAC transmit frame controller: Idle */ -#define ETH_MAC_TRANSMITFRAMECONTROLLER_WAITING ((uint32_t)0x00020000) /* MAC transmit frame controller: Waiting for Status of previous frame or IFG/backoff period to be over */ -#define ETH_MAC_TRANSMITFRAMECONTROLLER_GENRATING_PCF ((uint32_t)0x00040000) /* MAC transmit frame controller: Generating and transmitting a Pause control frame (in full duplex mode) */ -#define ETH_MAC_TRANSMITFRAMECONTROLLER_TRANSFERRING ((uint32_t)0x00060000) /* MAC transmit frame controller: Transferring input frame for transmission */ -#define ETH_MAC_MII_TRANSMIT_ACTIVE ((uint32_t)0x00010000) /* MAC MII transmit engine active */ -#define ETH_MAC_RXFIFO_EMPTY ((uint32_t)0x00000000) /* Rx FIFO fill level: empty */ -#define ETH_MAC_RXFIFO_BELOW_THRESHOLD ((uint32_t)0x00000100) /* Rx FIFO fill level: fill-level below flow-control de-activate threshold */ -#define ETH_MAC_RXFIFO_ABOVE_THRESHOLD ((uint32_t)0x00000200) /* Rx FIFO fill level: fill-level above flow-control activate threshold */ -#define ETH_MAC_RXFIFO_FULL ((uint32_t)0x00000300) /* Rx FIFO fill level: full */ +#define ETH_MMCCR 0x00000100U +#define ETH_MMCRIR 0x00000104U +#define ETH_MMCTIR 0x00000108U +#define ETH_MMCRIMR 0x0000010CU +#define ETH_MMCTIMR 0x00000110U +#define ETH_MMCTGFSCCR 0x0000014CU +#define ETH_MMCTGFMSCCR 0x00000150U +#define ETH_MMCTGFCR 0x00000168U +#define ETH_MMCRFCECR 0x00000194U +#define ETH_MMCRFAECR 0x00000198U +#define ETH_MMCRGUFCR 0x000001C4U + +#define ETH_MAC_TXFIFO_FULL 0x02000000U /* Tx FIFO full */ +#define ETH_MAC_TXFIFONOT_EMPTY 0x01000000U /* Tx FIFO not empty */ +#define ETH_MAC_TXFIFO_WRITE_ACTIVE 0x00400000U /* Tx FIFO write active */ +#define ETH_MAC_TXFIFO_IDLE 0x00000000U /* Tx FIFO read status: Idle */ +#define ETH_MAC_TXFIFO_READ 0x00100000U /* Tx FIFO read status: Read (transferring data to the MAC transmitter) */ +#define ETH_MAC_TXFIFO_WAITING 0x00200000U /* Tx FIFO read status: Waiting for TxStatus from MAC transmitter */ +#define ETH_MAC_TXFIFO_WRITING 0x00300000U /* Tx FIFO read status: Writing the received TxStatus or flushing the TxFIFO */ +#define ETH_MAC_TRANSMISSION_PAUSE 0x00080000U /* MAC transmitter in pause */ +#define ETH_MAC_TRANSMITFRAMECONTROLLER_IDLE 0x00000000U /* MAC transmit frame controller: Idle */ +#define ETH_MAC_TRANSMITFRAMECONTROLLER_WAITING 0x00020000U /* MAC transmit frame controller: Waiting for Status of previous frame or IFG/backoff period to be over */ +#define ETH_MAC_TRANSMITFRAMECONTROLLER_GENRATING_PCF 0x00040000U /* MAC transmit frame controller: Generating and transmitting a Pause control frame (in full duplex mode) */ +#define ETH_MAC_TRANSMITFRAMECONTROLLER_TRANSFERRING 0x00060000U /* MAC transmit frame controller: Transferring input frame for transmission */ +#define ETH_MAC_MII_TRANSMIT_ACTIVE 0x00010000U /* MAC MII transmit engine active */ +#define ETH_MAC_RXFIFO_EMPTY 0x00000000U /* Rx FIFO fill level: empty */ +#define ETH_MAC_RXFIFO_BELOW_THRESHOLD 0x00000100U /* Rx FIFO fill level: fill-level below flow-control de-activate threshold */ +#define ETH_MAC_RXFIFO_ABOVE_THRESHOLD 0x00000200U /* Rx FIFO fill level: fill-level above flow-control activate threshold */ +#define ETH_MAC_RXFIFO_FULL 0x00000300U /* Rx FIFO fill level: full */ #if defined(STM32F1) #else -#define ETH_MAC_READCONTROLLER_IDLE ((uint32_t)0x00000000) /* Rx FIFO read controller IDLE state */ -#define ETH_MAC_READCONTROLLER_READING_DATA ((uint32_t)0x00000020) /* Rx FIFO read controller Reading frame data */ -#define ETH_MAC_READCONTROLLER_READING_STATUS ((uint32_t)0x00000040) /* Rx FIFO read controller Reading frame status (or time-stamp) */ +#define ETH_MAC_READCONTROLLER_IDLE 0x00000000U /* Rx FIFO read controller IDLE state */ +#define ETH_MAC_READCONTROLLER_READING_DATA 0x00000020U /* Rx FIFO read controller Reading frame data */ +#define ETH_MAC_READCONTROLLER_READING_STATUS 0x00000040U /* Rx FIFO read controller Reading frame status (or time-stamp) */ #endif -#define ETH_MAC_READCONTROLLER_FLUSHING ((uint32_t)0x00000060) /* Rx FIFO read controller Flushing the frame data and status */ -#define ETH_MAC_RXFIFO_WRITE_ACTIVE ((uint32_t)0x00000010) /* Rx FIFO write controller active */ -#define ETH_MAC_SMALL_FIFO_NOTACTIVE ((uint32_t)0x00000000) /* MAC small FIFO read / write controllers not active */ -#define ETH_MAC_SMALL_FIFO_READ_ACTIVE ((uint32_t)0x00000002) /* MAC small FIFO read controller active */ -#define ETH_MAC_SMALL_FIFO_WRITE_ACTIVE ((uint32_t)0x00000004) /* MAC small FIFO write controller active */ -#define ETH_MAC_SMALL_FIFO_RW_ACTIVE ((uint32_t)0x00000006) /* MAC small FIFO read / write controllers active */ -#define ETH_MAC_MII_RECEIVE_PROTOCOL_ACTIVE ((uint32_t)0x00000001) /* MAC MII receive protocol engine active */ +#define ETH_MAC_READCONTROLLER_FLUSHING 0x00000060U /* Rx FIFO read controller Flushing the frame data and status */ +#define ETH_MAC_RXFIFO_WRITE_ACTIVE 0x00000010U /* Rx FIFO write controller active */ +#define ETH_MAC_SMALL_FIFO_NOTACTIVE 0x00000000U /* MAC small FIFO read / write controllers not active */ +#define ETH_MAC_SMALL_FIFO_READ_ACTIVE 0x00000002U /* MAC small FIFO read controller active */ +#define ETH_MAC_SMALL_FIFO_WRITE_ACTIVE 0x00000004U /* MAC small FIFO write controller active */ +#define ETH_MAC_SMALL_FIFO_RW_ACTIVE 0x00000006U /* MAC small FIFO read / write controllers active */ +#define ETH_MAC_MII_RECEIVE_PROTOCOL_ACTIVE 0x00000001U /* MAC MII receive protocol engine active */ /** * @} @@ -965,8 +1290,9 @@ extern "C" { * @} */ -#if defined(STM32L4xx) || defined(STM32F7) || defined(STM32F427xx) || defined(STM32F437xx) ||\ - defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) +#if defined(STM32L4) || defined(STM32F7) || defined(STM32F427xx) || defined(STM32F437xx) \ + || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) \ + || defined(STM32H7) /** @defgroup HAL_DMA2D_Aliased_Defines HAL DMA2D Aliased Defines maintained for legacy purpose * @{ */ @@ -990,7 +1316,7 @@ extern "C" { /** * @} */ -#endif /* STM32L4xx || STM32F7*/ +#endif /* STM32L4 || STM32F7 || STM32F4 || STM32H7 */ /** @defgroup HAL_PPP_Aliased_Defines HAL PPP Aliased Defines maintained for legacy purpose * @{ @@ -1082,6 +1408,28 @@ extern "C" { #define HAL_FMPI2CEx_DigitalFilter_Config HAL_FMPI2CEx_ConfigDigitalFilter #define HAL_I2CFastModePlusConfig(SYSCFG_I2CFastModePlus, cmd) (((cmd)==ENABLE)? HAL_I2CEx_EnableFastModePlus(SYSCFG_I2CFastModePlus): HAL_I2CEx_DisableFastModePlus(SYSCFG_I2CFastModePlus)) + +#if defined(STM32H7) || defined(STM32WB) || defined(STM32G0) || defined(STM32F4) || defined(STM32F7) || defined(STM32L0) || defined(STM32L4) || defined(STM32G4) +#define HAL_I2C_Master_Sequential_Transmit_IT HAL_I2C_Master_Seq_Transmit_IT +#define HAL_I2C_Master_Sequential_Receive_IT HAL_I2C_Master_Seq_Receive_IT +#define HAL_I2C_Slave_Sequential_Transmit_IT HAL_I2C_Slave_Seq_Transmit_IT +#define HAL_I2C_Slave_Sequential_Receive_IT HAL_I2C_Slave_Seq_Receive_IT +#define HAL_I2C_Master_Sequential_Transmit_DMA HAL_I2C_Master_Seq_Transmit_DMA +#define HAL_I2C_Master_Sequential_Receive_DMA HAL_I2C_Master_Seq_Receive_DMA +#define HAL_I2C_Slave_Sequential_Transmit_DMA HAL_I2C_Slave_Seq_Transmit_DMA +#define HAL_I2C_Slave_Sequential_Receive_DMA HAL_I2C_Slave_Seq_Receive_DMA +#endif /* STM32H7 || STM32WB || STM32G0 || STM32F4 || STM32F7 || STM32L0 || STM32L4 */ + +#if defined(STM32F4) +#define HAL_FMPI2C_Master_Sequential_Transmit_IT HAL_FMPI2C_Master_Seq_Transmit_IT +#define HAL_FMPI2C_Master_Sequential_Receive_IT HAL_FMPI2C_Master_Seq_Receive_IT +#define HAL_FMPI2C_Slave_Sequential_Transmit_IT HAL_FMPI2C_Slave_Seq_Transmit_IT +#define HAL_FMPI2C_Slave_Sequential_Receive_IT HAL_FMPI2C_Slave_Seq_Receive_IT +#define HAL_FMPI2C_Master_Sequential_Transmit_DMA HAL_FMPI2C_Master_Seq_Transmit_DMA +#define HAL_FMPI2C_Master_Sequential_Receive_DMA HAL_FMPI2C_Master_Seq_Receive_DMA +#define HAL_FMPI2C_Slave_Sequential_Transmit_DMA HAL_FMPI2C_Slave_Seq_Transmit_DMA +#define HAL_FMPI2C_Slave_Sequential_Receive_DMA HAL_FMPI2C_Slave_Seq_Receive_DMA +#endif /* STM32F4 */ /** * @} */ @@ -1116,6 +1464,8 @@ extern "C" { #define CR_OFFSET_BB PWR_CR_OFFSET_BB #define CSR_OFFSET_BB PWR_CSR_OFFSET_BB +#define PMODE_BIT_NUMBER VOS_BIT_NUMBER +#define CR_PMODE_BB CR_VOS_BB #define DBP_BitNumber DBP_BIT_NUMBER #define PVDE_BitNumber PVDE_BIT_NUMBER @@ -1159,6 +1509,14 @@ extern "C" { #define HAL_TIM_DMAError TIM_DMAError #define HAL_TIM_DMACaptureCplt TIM_DMACaptureCplt #define HAL_TIMEx_DMACommutationCplt TIMEx_DMACommutationCplt +#if defined(STM32H7) || defined(STM32G0) || defined(STM32F7) || defined(STM32F4) || defined(STM32L0) || defined(STM32L4) +#define HAL_TIM_SlaveConfigSynchronization HAL_TIM_SlaveConfigSynchro +#define HAL_TIM_SlaveConfigSynchronization_IT HAL_TIM_SlaveConfigSynchro_IT +#define HAL_TIMEx_CommutationCallback HAL_TIMEx_CommutCallback +#define HAL_TIMEx_ConfigCommutationEvent HAL_TIMEx_ConfigCommutEvent +#define HAL_TIMEx_ConfigCommutationEvent_IT HAL_TIMEx_ConfigCommutEvent_IT +#define HAL_TIMEx_ConfigCommutationEvent_DMA HAL_TIMEx_ConfigCommutEvent_DMA +#endif /* STM32H7 || STM32G0 || STM32F7 || STM32F4 || STM32L0 */ /** * @} */ @@ -1175,6 +1533,9 @@ extern "C" { * @{ */ #define HAL_LTDC_LineEvenCallback HAL_LTDC_LineEventCallback +#define HAL_LTDC_Relaod HAL_LTDC_Reload +#define HAL_LTDC_StructInitFromVideoConfig HAL_LTDCEx_StructInitFromVideoConfig +#define HAL_LTDC_StructInitFromAdaptedCommandConfig HAL_LTDCEx_StructInitFromAdaptedCommandConfig /** * @} */ @@ -1216,6 +1577,7 @@ extern "C" { #define __HAL_CLEAR_FLAG __HAL_SYSCFG_CLEAR_FLAG #define __HAL_VREFINT_OUT_ENABLE __HAL_SYSCFG_VREFINT_OUT_ENABLE #define __HAL_VREFINT_OUT_DISABLE __HAL_SYSCFG_VREFINT_OUT_DISABLE +#define __HAL_SYSCFG_SRAM2_WRP_ENABLE __HAL_SYSCFG_SRAM2_WRP_0_31_ENABLE #define SYSCFG_FLAG_VREF_READY SYSCFG_FLAG_VREFINT_READY #define SYSCFG_FLAG_RC48 RCC_FLAG_HSI48 @@ -1297,7 +1659,6 @@ extern "C" { #define __HAL_ADC_CR1_SCANCONV ADC_CR1_SCANCONV #define __HAL_ADC_CR2_EOCSelection ADC_CR2_EOCSelection #define __HAL_ADC_CR2_DMAContReq ADC_CR2_DMAContReq -#define __HAL_ADC_GET_RESOLUTION ADC_GET_RESOLUTION #define __HAL_ADC_JSQR ADC_JSQR #define __HAL_ADC_CHSELR_CHANNEL ADC_CHSELR_CHANNEL @@ -1369,10 +1730,17 @@ extern "C" { #define __HAL_UNFREEZE_TIM17_DBGMCU __HAL_DBGMCU_UNFREEZE_TIM17 #define __HAL_FREEZE_RTC_DBGMCU __HAL_DBGMCU_FREEZE_RTC #define __HAL_UNFREEZE_RTC_DBGMCU __HAL_DBGMCU_UNFREEZE_RTC +#if defined(STM32H7) +#define __HAL_FREEZE_WWDG_DBGMCU __HAL_DBGMCU_FREEZE_WWDG1 +#define __HAL_UNFREEZE_WWDG_DBGMCU __HAL_DBGMCU_UnFreeze_WWDG1 +#define __HAL_FREEZE_IWDG_DBGMCU __HAL_DBGMCU_FREEZE_IWDG1 +#define __HAL_UNFREEZE_IWDG_DBGMCU __HAL_DBGMCU_UnFreeze_IWDG1 +#else #define __HAL_FREEZE_WWDG_DBGMCU __HAL_DBGMCU_FREEZE_WWDG #define __HAL_UNFREEZE_WWDG_DBGMCU __HAL_DBGMCU_UNFREEZE_WWDG #define __HAL_FREEZE_IWDG_DBGMCU __HAL_DBGMCU_FREEZE_IWDG #define __HAL_UNFREEZE_IWDG_DBGMCU __HAL_DBGMCU_UNFREEZE_IWDG +#endif /* STM32H7 */ #define __HAL_FREEZE_I2C1_TIMEOUT_DBGMCU __HAL_DBGMCU_FREEZE_I2C1_TIMEOUT #define __HAL_UNFREEZE_I2C1_TIMEOUT_DBGMCU __HAL_DBGMCU_UNFREEZE_I2C1_TIMEOUT #define __HAL_FREEZE_I2C2_TIMEOUT_DBGMCU __HAL_DBGMCU_FREEZE_I2C2_TIMEOUT @@ -1610,7 +1978,11 @@ extern "C" { #define __HAL_I2C_RESET_CR2 I2C_RESET_CR2 #define __HAL_I2C_GENERATE_START I2C_GENERATE_START +#if defined(STM32F1) +#define __HAL_I2C_FREQ_RANGE I2C_FREQRANGE +#else #define __HAL_I2C_FREQ_RANGE I2C_FREQ_RANGE +#endif /* STM32F1 */ #define __HAL_I2C_RISE_TIME I2C_RISE_TIME #define __HAL_I2C_SPEED_STANDARD I2C_SPEED_STANDARD #define __HAL_I2C_SPEED_FAST I2C_SPEED_FAST @@ -1634,6 +2006,10 @@ extern "C" { #define IS_I2S_INSTANCE IS_I2S_ALL_INSTANCE #define IS_I2S_INSTANCE_EXT IS_I2S_ALL_INSTANCE_EXT +#if defined(STM32H7) +#define __HAL_I2S_CLEAR_FREFLAG __HAL_I2S_CLEAR_TIFREFLAG +#endif + /** * @} */ @@ -1770,20 +2146,20 @@ extern "C" { #define HAL_RCC_CCSCallback HAL_RCC_CSSCallback #define HAL_RC48_EnableBuffer_Cmd(cmd) (((cmd)==ENABLE) ? HAL_RCCEx_EnableHSI48_VREFINT() : HAL_RCCEx_DisableHSI48_VREFINT()) -#define __ADC_CLK_DISABLE __HAL_RCC_ADC_CLK_DISABLE -#define __ADC_CLK_ENABLE __HAL_RCC_ADC_CLK_ENABLE -#define __ADC_CLK_SLEEP_DISABLE __HAL_RCC_ADC_CLK_SLEEP_DISABLE -#define __ADC_CLK_SLEEP_ENABLE __HAL_RCC_ADC_CLK_SLEEP_ENABLE -#define __ADC_FORCE_RESET __HAL_RCC_ADC_FORCE_RESET -#define __ADC_RELEASE_RESET __HAL_RCC_ADC_RELEASE_RESET -#define __ADC1_CLK_DISABLE __HAL_RCC_ADC1_CLK_DISABLE -#define __ADC1_CLK_ENABLE __HAL_RCC_ADC1_CLK_ENABLE -#define __ADC1_FORCE_RESET __HAL_RCC_ADC1_FORCE_RESET -#define __ADC1_RELEASE_RESET __HAL_RCC_ADC1_RELEASE_RESET -#define __ADC1_CLK_SLEEP_ENABLE __HAL_RCC_ADC1_CLK_SLEEP_ENABLE -#define __ADC1_CLK_SLEEP_DISABLE __HAL_RCC_ADC1_CLK_SLEEP_DISABLE -#define __ADC2_CLK_DISABLE __HAL_RCC_ADC2_CLK_DISABLE -#define __ADC2_CLK_ENABLE __HAL_RCC_ADC2_CLK_ENABLE +#define __ADC_CLK_DISABLE __HAL_RCC_ADC_CLK_DISABLE +#define __ADC_CLK_ENABLE __HAL_RCC_ADC_CLK_ENABLE +#define __ADC_CLK_SLEEP_DISABLE __HAL_RCC_ADC_CLK_SLEEP_DISABLE +#define __ADC_CLK_SLEEP_ENABLE __HAL_RCC_ADC_CLK_SLEEP_ENABLE +#define __ADC_FORCE_RESET __HAL_RCC_ADC_FORCE_RESET +#define __ADC_RELEASE_RESET __HAL_RCC_ADC_RELEASE_RESET +#define __ADC1_CLK_DISABLE __HAL_RCC_ADC1_CLK_DISABLE +#define __ADC1_CLK_ENABLE __HAL_RCC_ADC1_CLK_ENABLE +#define __ADC1_FORCE_RESET __HAL_RCC_ADC1_FORCE_RESET +#define __ADC1_RELEASE_RESET __HAL_RCC_ADC1_RELEASE_RESET +#define __ADC1_CLK_SLEEP_ENABLE __HAL_RCC_ADC1_CLK_SLEEP_ENABLE +#define __ADC1_CLK_SLEEP_DISABLE __HAL_RCC_ADC1_CLK_SLEEP_DISABLE +#define __ADC2_CLK_DISABLE __HAL_RCC_ADC2_CLK_DISABLE +#define __ADC2_CLK_ENABLE __HAL_RCC_ADC2_CLK_ENABLE #define __ADC2_FORCE_RESET __HAL_RCC_ADC2_FORCE_RESET #define __ADC2_RELEASE_RESET __HAL_RCC_ADC2_RELEASE_RESET #define __ADC3_CLK_DISABLE __HAL_RCC_ADC3_CLK_DISABLE @@ -1800,7 +2176,7 @@ extern "C" { #define __CRYP_CLK_SLEEP_DISABLE __HAL_RCC_CRYP_CLK_SLEEP_DISABLE #define __CRYP_CLK_ENABLE __HAL_RCC_CRYP_CLK_ENABLE #define __CRYP_CLK_DISABLE __HAL_RCC_CRYP_CLK_DISABLE -#define __CRYP_FORCE_RESET __HAL_RCC_CRYP_FORCE_RESET +#define __CRYP_FORCE_RESET __HAL_RCC_CRYP_FORCE_RESET #define __CRYP_RELEASE_RESET __HAL_RCC_CRYP_RELEASE_RESET #define __AFIO_CLK_DISABLE __HAL_RCC_AFIO_CLK_DISABLE #define __AFIO_CLK_ENABLE __HAL_RCC_AFIO_CLK_ENABLE @@ -2028,6 +2404,21 @@ extern "C" { #define __QSPI_CLK_SLEEP_ENABLE __HAL_RCC_QSPI_CLK_SLEEP_ENABLE #define __QSPI_FORCE_RESET __HAL_RCC_QSPI_FORCE_RESET #define __QSPI_RELEASE_RESET __HAL_RCC_QSPI_RELEASE_RESET + +#if defined(STM32WB) +#define __HAL_RCC_QSPI_CLK_DISABLE __HAL_RCC_QUADSPI_CLK_DISABLE +#define __HAL_RCC_QSPI_CLK_ENABLE __HAL_RCC_QUADSPI_CLK_ENABLE +#define __HAL_RCC_QSPI_CLK_SLEEP_DISABLE __HAL_RCC_QUADSPI_CLK_SLEEP_DISABLE +#define __HAL_RCC_QSPI_CLK_SLEEP_ENABLE __HAL_RCC_QUADSPI_CLK_SLEEP_ENABLE +#define __HAL_RCC_QSPI_FORCE_RESET __HAL_RCC_QUADSPI_FORCE_RESET +#define __HAL_RCC_QSPI_RELEASE_RESET __HAL_RCC_QUADSPI_RELEASE_RESET +#define __HAL_RCC_QSPI_IS_CLK_ENABLED __HAL_RCC_QUADSPI_IS_CLK_ENABLED +#define __HAL_RCC_QSPI_IS_CLK_DISABLED __HAL_RCC_QUADSPI_IS_CLK_DISABLED +#define __HAL_RCC_QSPI_IS_CLK_SLEEP_ENABLED __HAL_RCC_QUADSPI_IS_CLK_SLEEP_ENABLED +#define __HAL_RCC_QSPI_IS_CLK_SLEEP_DISABLED __HAL_RCC_QUADSPI_IS_CLK_SLEEP_DISABLED +#define QSPI_IRQHandler QUADSPI_IRQHandler +#endif /* __HAL_RCC_QUADSPI_CLK_ENABLE */ + #define __RNG_CLK_DISABLE __HAL_RCC_RNG_CLK_DISABLE #define __RNG_CLK_ENABLE __HAL_RCC_RNG_CLK_ENABLE #define __RNG_CLK_SLEEP_DISABLE __HAL_RCC_RNG_CLK_SLEEP_DISABLE @@ -2216,26 +2607,26 @@ extern "C" { #define __USART3_CLK_SLEEP_ENABLE __HAL_RCC_USART3_CLK_SLEEP_ENABLE #define __USART3_FORCE_RESET __HAL_RCC_USART3_FORCE_RESET #define __USART3_RELEASE_RESET __HAL_RCC_USART3_RELEASE_RESET -#define __USART4_CLK_DISABLE __HAL_RCC_USART4_CLK_DISABLE -#define __USART4_CLK_ENABLE __HAL_RCC_USART4_CLK_ENABLE -#define __USART4_CLK_SLEEP_ENABLE __HAL_RCC_USART4_CLK_SLEEP_ENABLE -#define __USART4_CLK_SLEEP_DISABLE __HAL_RCC_USART4_CLK_SLEEP_DISABLE -#define __USART4_FORCE_RESET __HAL_RCC_USART4_FORCE_RESET -#define __USART4_RELEASE_RESET __HAL_RCC_USART4_RELEASE_RESET -#define __USART5_CLK_DISABLE __HAL_RCC_USART5_CLK_DISABLE -#define __USART5_CLK_ENABLE __HAL_RCC_USART5_CLK_ENABLE -#define __USART5_CLK_SLEEP_ENABLE __HAL_RCC_USART5_CLK_SLEEP_ENABLE -#define __USART5_CLK_SLEEP_DISABLE __HAL_RCC_USART5_CLK_SLEEP_DISABLE -#define __USART5_FORCE_RESET __HAL_RCC_USART5_FORCE_RESET -#define __USART5_RELEASE_RESET __HAL_RCC_USART5_RELEASE_RESET -#define __USART7_CLK_DISABLE __HAL_RCC_USART7_CLK_DISABLE -#define __USART7_CLK_ENABLE __HAL_RCC_USART7_CLK_ENABLE -#define __USART7_FORCE_RESET __HAL_RCC_USART7_FORCE_RESET -#define __USART7_RELEASE_RESET __HAL_RCC_USART7_RELEASE_RESET -#define __USART8_CLK_DISABLE __HAL_RCC_USART8_CLK_DISABLE -#define __USART8_CLK_ENABLE __HAL_RCC_USART8_CLK_ENABLE -#define __USART8_FORCE_RESET __HAL_RCC_USART8_FORCE_RESET -#define __USART8_RELEASE_RESET __HAL_RCC_USART8_RELEASE_RESET +#define __USART4_CLK_DISABLE __HAL_RCC_UART4_CLK_DISABLE +#define __USART4_CLK_ENABLE __HAL_RCC_UART4_CLK_ENABLE +#define __USART4_CLK_SLEEP_ENABLE __HAL_RCC_UART4_CLK_SLEEP_ENABLE +#define __USART4_CLK_SLEEP_DISABLE __HAL_RCC_UART4_CLK_SLEEP_DISABLE +#define __USART4_FORCE_RESET __HAL_RCC_UART4_FORCE_RESET +#define __USART4_RELEASE_RESET __HAL_RCC_UART4_RELEASE_RESET +#define __USART5_CLK_DISABLE __HAL_RCC_UART5_CLK_DISABLE +#define __USART5_CLK_ENABLE __HAL_RCC_UART5_CLK_ENABLE +#define __USART5_CLK_SLEEP_ENABLE __HAL_RCC_UART5_CLK_SLEEP_ENABLE +#define __USART5_CLK_SLEEP_DISABLE __HAL_RCC_UART5_CLK_SLEEP_DISABLE +#define __USART5_FORCE_RESET __HAL_RCC_UART5_FORCE_RESET +#define __USART5_RELEASE_RESET __HAL_RCC_UART5_RELEASE_RESET +#define __USART7_CLK_DISABLE __HAL_RCC_UART7_CLK_DISABLE +#define __USART7_CLK_ENABLE __HAL_RCC_UART7_CLK_ENABLE +#define __USART7_FORCE_RESET __HAL_RCC_UART7_FORCE_RESET +#define __USART7_RELEASE_RESET __HAL_RCC_UART7_RELEASE_RESET +#define __USART8_CLK_DISABLE __HAL_RCC_UART8_CLK_DISABLE +#define __USART8_CLK_ENABLE __HAL_RCC_UART8_CLK_ENABLE +#define __USART8_FORCE_RESET __HAL_RCC_UART8_FORCE_RESET +#define __USART8_RELEASE_RESET __HAL_RCC_UART8_RELEASE_RESET #define __USB_CLK_DISABLE __HAL_RCC_USB_CLK_DISABLE #define __USB_CLK_ENABLE __HAL_RCC_USB_CLK_ENABLE #define __USB_FORCE_RESET __HAL_RCC_USB_FORCE_RESET @@ -2244,12 +2635,28 @@ extern "C" { #define __USB_OTG_FS_CLK_DISABLE __HAL_RCC_USB_OTG_FS_CLK_DISABLE #define __USB_OTG_FS_CLK_ENABLE __HAL_RCC_USB_OTG_FS_CLK_ENABLE #define __USB_RELEASE_RESET __HAL_RCC_USB_RELEASE_RESET + +#if defined(STM32H7) +#define __HAL_RCC_WWDG_CLK_DISABLE __HAL_RCC_WWDG1_CLK_DISABLE +#define __HAL_RCC_WWDG_CLK_ENABLE __HAL_RCC_WWDG1_CLK_ENABLE +#define __HAL_RCC_WWDG_CLK_SLEEP_DISABLE __HAL_RCC_WWDG1_CLK_SLEEP_DISABLE +#define __HAL_RCC_WWDG_CLK_SLEEP_ENABLE __HAL_RCC_WWDG1_CLK_SLEEP_ENABLE + +#define __HAL_RCC_WWDG_FORCE_RESET ((void)0U) /* Not available on the STM32H7*/ +#define __HAL_RCC_WWDG_RELEASE_RESET ((void)0U) /* Not available on the STM32H7*/ + + +#define __HAL_RCC_WWDG_IS_CLK_ENABLED __HAL_RCC_WWDG1_IS_CLK_ENABLED +#define __HAL_RCC_WWDG_IS_CLK_DISABLED __HAL_RCC_WWDG1_IS_CLK_DISABLED +#endif + #define __WWDG_CLK_DISABLE __HAL_RCC_WWDG_CLK_DISABLE #define __WWDG_CLK_ENABLE __HAL_RCC_WWDG_CLK_ENABLE #define __WWDG_CLK_SLEEP_DISABLE __HAL_RCC_WWDG_CLK_SLEEP_DISABLE #define __WWDG_CLK_SLEEP_ENABLE __HAL_RCC_WWDG_CLK_SLEEP_ENABLE #define __WWDG_FORCE_RESET __HAL_RCC_WWDG_FORCE_RESET #define __WWDG_RELEASE_RESET __HAL_RCC_WWDG_RELEASE_RESET + #define __TIM21_CLK_ENABLE __HAL_RCC_TIM21_CLK_ENABLE #define __TIM21_CLK_DISABLE __HAL_RCC_TIM21_CLK_DISABLE #define __TIM21_FORCE_RESET __HAL_RCC_TIM21_FORCE_RESET @@ -2395,7 +2802,6 @@ extern "C" { #define __HAL_RCC_OTGHSULPI_CLK_SLEEP_DISABLE __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_DISABLE #define __HAL_RCC_OTGHSULPI_IS_CLK_SLEEP_ENABLED __HAL_RCC_USB_OTG_HS_ULPI_IS_CLK_SLEEP_ENABLED #define __HAL_RCC_OTGHSULPI_IS_CLK_SLEEP_DISABLED __HAL_RCC_USB_OTG_HS_ULPI_IS_CLK_SLEEP_DISABLED -#define __CRYP_FORCE_RESET __HAL_RCC_CRYP_FORCE_RESET #define __SRAM3_CLK_SLEEP_ENABLE __HAL_RCC_SRAM3_CLK_SLEEP_ENABLE #define __CAN2_CLK_SLEEP_ENABLE __HAL_RCC_CAN2_CLK_SLEEP_ENABLE #define __CAN2_CLK_SLEEP_DISABLE __HAL_RCC_CAN2_CLK_SLEEP_DISABLE @@ -2428,8 +2834,6 @@ extern "C" { #define __ADC12_CLK_DISABLE __HAL_RCC_ADC12_CLK_DISABLE #define __ADC34_CLK_ENABLE __HAL_RCC_ADC34_CLK_ENABLE #define __ADC34_CLK_DISABLE __HAL_RCC_ADC34_CLK_DISABLE -#define __ADC12_CLK_ENABLE __HAL_RCC_ADC12_CLK_ENABLE -#define __ADC12_CLK_DISABLE __HAL_RCC_ADC12_CLK_DISABLE #define __DAC2_CLK_ENABLE __HAL_RCC_DAC2_CLK_ENABLE #define __DAC2_CLK_DISABLE __HAL_RCC_DAC2_CLK_DISABLE #define __TIM18_CLK_ENABLE __HAL_RCC_TIM18_CLK_ENABLE @@ -2451,8 +2855,6 @@ extern "C" { #define __ADC12_RELEASE_RESET __HAL_RCC_ADC12_RELEASE_RESET #define __ADC34_FORCE_RESET __HAL_RCC_ADC34_FORCE_RESET #define __ADC34_RELEASE_RESET __HAL_RCC_ADC34_RELEASE_RESET -#define __ADC12_FORCE_RESET __HAL_RCC_ADC12_FORCE_RESET -#define __ADC12_RELEASE_RESET __HAL_RCC_ADC12_RELEASE_RESET #define __DAC2_FORCE_RESET __HAL_RCC_DAC2_FORCE_RESET #define __DAC2_RELEASE_RESET __HAL_RCC_DAC2_RELEASE_RESET #define __TIM18_FORCE_RESET __HAL_RCC_TIM18_FORCE_RESET @@ -2587,6 +2989,15 @@ extern "C" { #define __WWDG_IS_CLK_ENABLED __HAL_RCC_WWDG_IS_CLK_ENABLED #define __WWDG_IS_CLK_DISABLED __HAL_RCC_WWDG_IS_CLK_DISABLED +#if defined(STM32L1) +#define __HAL_RCC_CRYP_CLK_DISABLE __HAL_RCC_AES_CLK_DISABLE +#define __HAL_RCC_CRYP_CLK_ENABLE __HAL_RCC_AES_CLK_ENABLE +#define __HAL_RCC_CRYP_CLK_SLEEP_DISABLE __HAL_RCC_AES_CLK_SLEEP_DISABLE +#define __HAL_RCC_CRYP_CLK_SLEEP_ENABLE __HAL_RCC_AES_CLK_SLEEP_ENABLE +#define __HAL_RCC_CRYP_FORCE_RESET __HAL_RCC_AES_FORCE_RESET +#define __HAL_RCC_CRYP_RELEASE_RESET __HAL_RCC_AES_RELEASE_RESET +#endif /* STM32L1 */ + #if defined(STM32F4) #define __HAL_RCC_SDMMC1_FORCE_RESET __HAL_RCC_SDIO_FORCE_RESET #define __HAL_RCC_SDMMC1_RELEASE_RESET __HAL_RCC_SDIO_RELEASE_RESET @@ -2624,6 +3035,30 @@ extern "C" { #define RCC_SDIOCLKSOURCE_SYSCLK RCC_SDMMC1CLKSOURCE_SYSCLK #endif +#if defined(STM32H7) +#define __HAL_RCC_USB_OTG_HS_CLK_ENABLE() __HAL_RCC_USB1_OTG_HS_CLK_ENABLE() +#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE() __HAL_RCC_USB1_OTG_HS_ULPI_CLK_ENABLE() +#define __HAL_RCC_USB_OTG_HS_CLK_DISABLE() __HAL_RCC_USB1_OTG_HS_CLK_DISABLE() +#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_DISABLE() __HAL_RCC_USB1_OTG_HS_ULPI_CLK_DISABLE() +#define __HAL_RCC_USB_OTG_HS_FORCE_RESET() __HAL_RCC_USB1_OTG_HS_FORCE_RESET() +#define __HAL_RCC_USB_OTG_HS_RELEASE_RESET() __HAL_RCC_USB1_OTG_HS_RELEASE_RESET() +#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_ENABLE() __HAL_RCC_USB1_OTG_HS_CLK_SLEEP_ENABLE() +#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_ENABLE() __HAL_RCC_USB1_OTG_HS_ULPI_CLK_SLEEP_ENABLE() +#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_DISABLE() __HAL_RCC_USB1_OTG_HS_CLK_SLEEP_DISABLE() +#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_DISABLE() __HAL_RCC_USB1_OTG_HS_ULPI_CLK_SLEEP_DISABLE() + +#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() __HAL_RCC_USB2_OTG_FS_CLK_ENABLE() +#define __HAL_RCC_USB_OTG_FS_ULPI_CLK_ENABLE() __HAL_RCC_USB2_OTG_FS_ULPI_CLK_ENABLE() +#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() __HAL_RCC_USB2_OTG_FS_CLK_DISABLE() +#define __HAL_RCC_USB_OTG_FS_ULPI_CLK_DISABLE() __HAL_RCC_USB2_OTG_FS_ULPI_CLK_DISABLE() +#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() __HAL_RCC_USB2_OTG_FS_FORCE_RESET() +#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() __HAL_RCC_USB2_OTG_FS_RELEASE_RESET() +#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() __HAL_RCC_USB2_OTG_FS_CLK_SLEEP_ENABLE() +#define __HAL_RCC_USB_OTG_FS_ULPI_CLK_SLEEP_ENABLE() __HAL_RCC_USB2_OTG_FS_ULPI_CLK_SLEEP_ENABLE() +#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() __HAL_RCC_USB2_OTG_FS_CLK_SLEEP_DISABLE() +#define __HAL_RCC_USB_OTG_FS_ULPI_CLK_SLEEP_DISABLE() __HAL_RCC_USB2_OTG_FS_ULPI_CLK_SLEEP_DISABLE() +#endif + #define __HAL_RCC_I2SCLK __HAL_RCC_I2S_CONFIG #define __HAL_RCC_I2SCLK_CONFIG __HAL_RCC_I2S_CONFIG @@ -2637,10 +3072,22 @@ extern "C" { #define RCC_IT_HSI14 RCC_IT_HSI14RDY -#if defined(STM32L0) -#define RCC_IT_LSECSS RCC_IT_CSSLSE -#define RCC_IT_CSS RCC_IT_CSSHSE -#endif +#define RCC_IT_CSSLSE RCC_IT_LSECSS +#define RCC_IT_CSSHSE RCC_IT_CSS + +#define RCC_PLLMUL_3 RCC_PLL_MUL3 +#define RCC_PLLMUL_4 RCC_PLL_MUL4 +#define RCC_PLLMUL_6 RCC_PLL_MUL6 +#define RCC_PLLMUL_8 RCC_PLL_MUL8 +#define RCC_PLLMUL_12 RCC_PLL_MUL12 +#define RCC_PLLMUL_16 RCC_PLL_MUL16 +#define RCC_PLLMUL_24 RCC_PLL_MUL24 +#define RCC_PLLMUL_32 RCC_PLL_MUL32 +#define RCC_PLLMUL_48 RCC_PLL_MUL48 + +#define RCC_PLLDIV_2 RCC_PLL_DIV2 +#define RCC_PLLDIV_3 RCC_PLL_DIV3 +#define RCC_PLLDIV_4 RCC_PLL_DIV4 #define IS_RCC_MCOSOURCE IS_RCC_MCO1SOURCE #define __HAL_RCC_MCO_CONFIG __HAL_RCC_MCO1_CONFIG @@ -2665,7 +3112,12 @@ extern "C" { #define RCC_MCOSOURCE_PLLCLK_NODIV RCC_MCO1SOURCE_PLLCLK #define RCC_MCOSOURCE_PLLCLK_DIV2 RCC_MCO1SOURCE_PLLCLK_DIV2 +#if defined(STM32L4) +#define RCC_RTCCLKSOURCE_NO_CLK RCC_RTCCLKSOURCE_NONE +#elif defined(STM32WB) || defined(STM32G0) || defined(STM32G4) +#else #define RCC_RTCCLKSOURCE_NONE RCC_RTCCLKSOURCE_NO_CLK +#endif #define RCC_USBCLK_PLLSAI1 RCC_USBCLKSOURCE_PLLSAI1 #define RCC_USBCLK_PLL RCC_USBCLKSOURCE_PLL @@ -2757,10 +3209,22 @@ extern "C" { #define __HAL_RCC_DFSDM_IS_CLK_SLEEP_DISABLED __HAL_RCC_DFSDM1_IS_CLK_SLEEP_DISABLED #define DfsdmClockSelection Dfsdm1ClockSelection #define RCC_PERIPHCLK_DFSDM RCC_PERIPHCLK_DFSDM1 -#define RCC_DFSDMCLKSOURCE_PCLK RCC_DFSDM1CLKSOURCE_PCLK +#define RCC_DFSDMCLKSOURCE_PCLK RCC_DFSDM1CLKSOURCE_PCLK2 #define RCC_DFSDMCLKSOURCE_SYSCLK RCC_DFSDM1CLKSOURCE_SYSCLK #define __HAL_RCC_DFSDM_CONFIG __HAL_RCC_DFSDM1_CONFIG #define __HAL_RCC_GET_DFSDM_SOURCE __HAL_RCC_GET_DFSDM1_SOURCE +#define RCC_DFSDM1CLKSOURCE_PCLK RCC_DFSDM1CLKSOURCE_PCLK2 +#define RCC_SWPMI1CLKSOURCE_PCLK RCC_SWPMI1CLKSOURCE_PCLK1 +#define RCC_LPTIM1CLKSOURCE_PCLK RCC_LPTIM1CLKSOURCE_PCLK1 +#define RCC_LPTIM2CLKSOURCE_PCLK RCC_LPTIM2CLKSOURCE_PCLK1 + +#define RCC_DFSDM1AUDIOCLKSOURCE_I2SAPB1 RCC_DFSDM1AUDIOCLKSOURCE_I2S1 +#define RCC_DFSDM1AUDIOCLKSOURCE_I2SAPB2 RCC_DFSDM1AUDIOCLKSOURCE_I2S2 +#define RCC_DFSDM2AUDIOCLKSOURCE_I2SAPB1 RCC_DFSDM2AUDIOCLKSOURCE_I2S1 +#define RCC_DFSDM2AUDIOCLKSOURCE_I2SAPB2 RCC_DFSDM2AUDIOCLKSOURCE_I2S2 +#define RCC_DFSDM1CLKSOURCE_APB2 RCC_DFSDM1CLKSOURCE_PCLK2 +#define RCC_DFSDM2CLKSOURCE_APB2 RCC_DFSDM2CLKSOURCE_PCLK2 +#define RCC_FMPI2C1CLKSOURCE_APB RCC_FMPI2C1CLKSOURCE_PCLK1 /** * @} @@ -2778,8 +3242,10 @@ extern "C" { /** @defgroup HAL_RTC_Aliased_Macros HAL RTC Aliased Macros maintained for legacy purpose * @{ */ - +#if defined (STM32G0) || defined (STM32L412xx) || defined (STM32L422xx) || defined (STM32G4) +#else #define __HAL_RTC_CLEAR_FLAG __HAL_RTC_EXTI_CLEAR_FLAG +#endif #define __HAL_RTC_DISABLE_IT __HAL_RTC_EXTI_DISABLE_IT #define __HAL_RTC_ENABLE_IT __HAL_RTC_EXTI_ENABLE_IT @@ -2840,7 +3306,7 @@ extern "C" { #define SD_OCR_CID_CSD_OVERWRIETE SD_OCR_CID_CSD_OVERWRITE #define SD_CMD_SD_APP_STAUS SD_CMD_SD_APP_STATUS -#if defined(STM32F4) +#if defined(STM32F4) || defined(STM32F2) #define SD_SDMMC_DISABLED SD_SDIO_DISABLED #define SD_SDMMC_FUNCTION_BUSY SD_SDIO_FUNCTION_BUSY #define SD_SDMMC_FUNCTION_FAILED SD_SDIO_FUNCTION_FAILED @@ -2891,6 +3357,25 @@ extern "C" { #define SDIO_IRQn SDMMC1_IRQn #define SDIO_IRQHandler SDMMC1_IRQHandler #endif + +#if defined(STM32F7) || defined(STM32F4) || defined(STM32F2) || defined(STM32L4) || defined(STM32H7) +#define HAL_SD_CardCIDTypedef HAL_SD_CardCIDTypeDef +#define HAL_SD_CardCSDTypedef HAL_SD_CardCSDTypeDef +#define HAL_SD_CardStatusTypedef HAL_SD_CardStatusTypeDef +#define HAL_SD_CardStateTypedef HAL_SD_CardStateTypeDef +#endif + +#if defined(STM32H7) +#define HAL_MMCEx_Read_DMADoubleBuffer0CpltCallback HAL_MMCEx_Read_DMADoubleBuf0CpltCallback +#define HAL_MMCEx_Read_DMADoubleBuffer1CpltCallback HAL_MMCEx_Read_DMADoubleBuf1CpltCallback +#define HAL_MMCEx_Write_DMADoubleBuffer0CpltCallback HAL_MMCEx_Write_DMADoubleBuf0CpltCallback +#define HAL_MMCEx_Write_DMADoubleBuffer1CpltCallback HAL_MMCEx_Write_DMADoubleBuf1CpltCallback +#define HAL_SDEx_Read_DMADoubleBuffer0CpltCallback HAL_SDEx_Read_DMADoubleBuf0CpltCallback +#define HAL_SDEx_Read_DMADoubleBuffer1CpltCallback HAL_SDEx_Read_DMADoubleBuf1CpltCallback +#define HAL_SDEx_Write_DMADoubleBuffer0CpltCallback HAL_SDEx_Write_DMADoubleBuf0CpltCallback +#define HAL_SDEx_Write_DMADoubleBuffer1CpltCallback HAL_SDEx_Write_DMADoubleBuf1CpltCallback +#define HAL_SD_DriveTransciver_1_8V_Callback HAL_SD_DriveTransceiver_1_8V_Callback +#endif /** * @} */ @@ -3079,6 +3564,7 @@ extern "C" { * @{ */ #define __HAL_LTDC_LAYER LTDC_LAYER +#define __HAL_LTDC_RELOAD_CONFIG __HAL_LTDC_RELOAD_IMMEDIATE_CONFIG /** * @} */ @@ -3104,6 +3590,42 @@ extern "C" { * @} */ +/** @defgroup HAL_SPDIFRX_Aliased_Macros HAL SPDIFRX Aliased Macros maintained for legacy purpose + * @{ + */ +#if defined(STM32H7) +#define HAL_SPDIFRX_ReceiveControlFlow HAL_SPDIFRX_ReceiveCtrlFlow +#define HAL_SPDIFRX_ReceiveControlFlow_IT HAL_SPDIFRX_ReceiveCtrlFlow_IT +#define HAL_SPDIFRX_ReceiveControlFlow_DMA HAL_SPDIFRX_ReceiveCtrlFlow_DMA +#endif +/** + * @} + */ + +/** @defgroup HAL_HRTIM_Aliased_Functions HAL HRTIM Aliased Functions maintained for legacy purpose + * @{ + */ +#if defined (STM32H7) || defined (STM32G4) || defined (STM32F3) +#define HAL_HRTIM_WaveformCounterStart_IT HAL_HRTIM_WaveformCountStart_IT +#define HAL_HRTIM_WaveformCounterStart_DMA HAL_HRTIM_WaveformCountStart_DMA +#define HAL_HRTIM_WaveformCounterStart HAL_HRTIM_WaveformCountStart +#define HAL_HRTIM_WaveformCounterStop_IT HAL_HRTIM_WaveformCountStop_IT +#define HAL_HRTIM_WaveformCounterStop_DMA HAL_HRTIM_WaveformCountStop_DMA +#define HAL_HRTIM_WaveformCounterStop HAL_HRTIM_WaveformCountStop +#endif +/** + * @} + */ + +/** @defgroup HAL_QSPI_Aliased_Macros HAL QSPI Aliased Macros maintained for legacy purpose + * @{ + */ +#if defined (STM32L4) +#define HAL_QPSI_TIMEOUT_DEFAULT_VALUE HAL_QSPI_TIMEOUT_DEFAULT_VALUE +#endif +/** + * @} + */ /** @defgroup HAL_PPP_Aliased_Macros HAL PPP Aliased Macros maintained for legacy purpose * @{ @@ -3117,7 +3639,7 @@ extern "C" { } #endif -#endif /* ___STM32_HAL_LEGACY */ +#endif /* STM32_HAL_LEGACY */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal.h new file mode 100644 index 00000000..f4db6bbb --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal.h @@ -0,0 +1,357 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal.h + * @author MCD Application Team + * @brief This file contains all the functions prototypes for the HAL + * module driver. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2017 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F1xx_HAL_H +#define __STM32F1xx_HAL_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal_conf.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @addtogroup HAL + * @{ + */ + +/* Exported constants --------------------------------------------------------*/ + +/** @defgroup HAL_Exported_Constants HAL Exported Constants + * @{ + */ + +/** @defgroup HAL_TICK_FREQ Tick Frequency + * @{ + */ +typedef enum +{ + HAL_TICK_FREQ_10HZ = 100U, + HAL_TICK_FREQ_100HZ = 10U, + HAL_TICK_FREQ_1KHZ = 1U, + HAL_TICK_FREQ_DEFAULT = HAL_TICK_FREQ_1KHZ +} HAL_TickFreqTypeDef; +/** + * @} + */ +/* Exported types ------------------------------------------------------------*/ +extern uint32_t uwTickPrio; +extern HAL_TickFreqTypeDef uwTickFreq; + +/** + * @} + */ +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup HAL_Exported_Macros HAL Exported Macros + * @{ + */ + +/** @defgroup DBGMCU_Freeze_Unfreeze Freeze Unfreeze Peripherals in Debug mode + * @brief Freeze/Unfreeze Peripherals in Debug mode + * Note: On devices STM32F10xx8 and STM32F10xxB, + * STM32F101xC/D/E and STM32F103xC/D/E, + * STM32F101xF/G and STM32F103xF/G + * STM32F10xx4 and STM32F10xx6 + * Debug registers DBGMCU_IDCODE and DBGMCU_CR are accessible only in + * debug mode (not accessible by the user software in normal mode). + * Refer to errata sheet of these devices for more details. + * @{ + */ + +/* Peripherals on APB1 */ +/** + * @brief TIM2 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM2() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM2_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM2() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM2_STOP) + +/** + * @brief TIM3 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM3() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM3_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM3() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM3_STOP) + +#if defined (DBGMCU_CR_DBG_TIM4_STOP) +/** + * @brief TIM4 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM4() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM4_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM4() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM4_STOP) +#endif + +#if defined (DBGMCU_CR_DBG_TIM5_STOP) +/** + * @brief TIM5 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM5() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM5_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM5() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM5_STOP) +#endif + +#if defined (DBGMCU_CR_DBG_TIM6_STOP) +/** + * @brief TIM6 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM6() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM6_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM6() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM6_STOP) +#endif + +#if defined (DBGMCU_CR_DBG_TIM7_STOP) +/** + * @brief TIM7 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM7() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM7_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM7() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM7_STOP) +#endif + +#if defined (DBGMCU_CR_DBG_TIM12_STOP) +/** + * @brief TIM12 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM12() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM12_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM12() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM12_STOP) +#endif + +#if defined (DBGMCU_CR_DBG_TIM13_STOP) +/** + * @brief TIM13 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM13() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM13_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM13() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM13_STOP) +#endif + +#if defined (DBGMCU_CR_DBG_TIM14_STOP) +/** + * @brief TIM14 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM14() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM14_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM14() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM14_STOP) +#endif + +/** + * @brief WWDG Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_WWDG() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_WWDG_STOP) +#define __HAL_DBGMCU_UNFREEZE_WWDG() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_WWDG_STOP) + +/** + * @brief IWDG Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_IWDG() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_IWDG_STOP) +#define __HAL_DBGMCU_UNFREEZE_IWDG() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_IWDG_STOP) + +/** + * @brief I2C1 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_I2C1_TIMEOUT() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_I2C1_SMBUS_TIMEOUT) +#define __HAL_DBGMCU_UNFREEZE_I2C1_TIMEOUT() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_I2C1_SMBUS_TIMEOUT) + +#if defined (DBGMCU_CR_DBG_I2C2_SMBUS_TIMEOUT) +/** + * @brief I2C2 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_I2C2_TIMEOUT() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_I2C2_SMBUS_TIMEOUT) +#define __HAL_DBGMCU_UNFREEZE_I2C2_TIMEOUT() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_I2C2_SMBUS_TIMEOUT) +#endif + +#if defined (DBGMCU_CR_DBG_CAN1_STOP) +/** + * @brief CAN1 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_CAN1() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_CAN1_STOP) +#define __HAL_DBGMCU_UNFREEZE_CAN1() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_CAN1_STOP) +#endif + +#if defined (DBGMCU_CR_DBG_CAN2_STOP) +/** + * @brief CAN2 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_CAN2() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_CAN2_STOP) +#define __HAL_DBGMCU_UNFREEZE_CAN2() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_CAN2_STOP) +#endif + +/* Peripherals on APB2 */ +#if defined (DBGMCU_CR_DBG_TIM1_STOP) +/** + * @brief TIM1 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM1() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM1_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM1() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM1_STOP) +#endif + +#if defined (DBGMCU_CR_DBG_TIM8_STOP) +/** + * @brief TIM8 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM8() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM8_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM8() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM8_STOP) +#endif + +#if defined (DBGMCU_CR_DBG_TIM9_STOP) +/** + * @brief TIM9 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM9() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM9_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM9() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM9_STOP) +#endif + +#if defined (DBGMCU_CR_DBG_TIM10_STOP) +/** + * @brief TIM10 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM10() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM10_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM10() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM10_STOP) +#endif + +#if defined (DBGMCU_CR_DBG_TIM11_STOP) +/** + * @brief TIM11 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM11() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM11_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM11() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM11_STOP) +#endif + + +#if defined (DBGMCU_CR_DBG_TIM15_STOP) +/** + * @brief TIM15 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM15() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM15_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM15() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM15_STOP) +#endif + +#if defined (DBGMCU_CR_DBG_TIM16_STOP) +/** + * @brief TIM16 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM16() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM16_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM16() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM16_STOP) +#endif + +#if defined (DBGMCU_CR_DBG_TIM17_STOP) +/** + * @brief TIM17 Peripherals Debug mode + */ +#define __HAL_DBGMCU_FREEZE_TIM17() SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM17_STOP) +#define __HAL_DBGMCU_UNFREEZE_TIM17() CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM17_STOP) +#endif + +/** + * @} + */ + +/** @defgroup HAL_Private_Macros HAL Private Macros + * @{ + */ +#define IS_TICKFREQ(FREQ) (((FREQ) == HAL_TICK_FREQ_10HZ) || \ + ((FREQ) == HAL_TICK_FREQ_100HZ) || \ + ((FREQ) == HAL_TICK_FREQ_1KHZ)) +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup HAL_Exported_Functions + * @{ + */ +/** @addtogroup HAL_Exported_Functions_Group1 + * @{ + */ +/* Initialization and de-initialization functions ******************************/ +HAL_StatusTypeDef HAL_Init(void); +HAL_StatusTypeDef HAL_DeInit(void); +void HAL_MspInit(void); +void HAL_MspDeInit(void); +HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority); +/** + * @} + */ + +/** @addtogroup HAL_Exported_Functions_Group2 + * @{ + */ +/* Peripheral Control functions ************************************************/ +void HAL_IncTick(void); +void HAL_Delay(uint32_t Delay); +uint32_t HAL_GetTick(void); +uint32_t HAL_GetTickPrio(void); +HAL_StatusTypeDef HAL_SetTickFreq(HAL_TickFreqTypeDef Freq); +HAL_TickFreqTypeDef HAL_GetTickFreq(void); +void HAL_SuspendTick(void); +void HAL_ResumeTick(void); +uint32_t HAL_GetHalVersion(void); +uint32_t HAL_GetREVID(void); +uint32_t HAL_GetDEVID(void); +uint32_t HAL_GetUIDw0(void); +uint32_t HAL_GetUIDw1(void); +uint32_t HAL_GetUIDw2(void); +void HAL_DBGMCU_EnableDBGSleepMode(void); +void HAL_DBGMCU_DisableDBGSleepMode(void); +void HAL_DBGMCU_EnableDBGStopMode(void); +void HAL_DBGMCU_DisableDBGStopMode(void); +void HAL_DBGMCU_EnableDBGStandbyMode(void); +void HAL_DBGMCU_DisableDBGStandbyMode(void); +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ +/* Private types -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/** @defgroup HAL_Private_Variables HAL Private Variables + * @{ + */ +/** + * @} + */ +/* Private constants ---------------------------------------------------------*/ +/** @defgroup HAL_Private_Constants HAL Private Constants + * @{ + */ +/** + * @} + */ +/* Private macros ------------------------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F1xx_HAL_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_can.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_can.h new file mode 100644 index 00000000..b44f3398 --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_can.h @@ -0,0 +1,850 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_can.h + * @author MCD Application Team + * @brief Header file of CAN HAL module. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef STM32F1xx_HAL_CAN_H +#define STM32F1xx_HAL_CAN_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal_def.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +#if defined (CAN1) +/** @addtogroup CAN + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ +/** @defgroup CAN_Exported_Types CAN Exported Types + * @{ + */ +/** + * @brief HAL State structures definition + */ +typedef enum +{ + HAL_CAN_STATE_RESET = 0x00U, /*!< CAN not yet initialized or disabled */ + HAL_CAN_STATE_READY = 0x01U, /*!< CAN initialized and ready for use */ + HAL_CAN_STATE_LISTENING = 0x02U, /*!< CAN receive process is ongoing */ + HAL_CAN_STATE_SLEEP_PENDING = 0x03U, /*!< CAN sleep request is pending */ + HAL_CAN_STATE_SLEEP_ACTIVE = 0x04U, /*!< CAN sleep mode is active */ + HAL_CAN_STATE_ERROR = 0x05U /*!< CAN error state */ + +} HAL_CAN_StateTypeDef; + +/** + * @brief CAN init structure definition + */ +typedef struct +{ + uint32_t Prescaler; /*!< Specifies the length of a time quantum. + This parameter must be a number between Min_Data = 1 and Max_Data = 1024. */ + + uint32_t Mode; /*!< Specifies the CAN operating mode. + This parameter can be a value of @ref CAN_operating_mode */ + + uint32_t SyncJumpWidth; /*!< Specifies the maximum number of time quanta the CAN hardware + is allowed to lengthen or shorten a bit to perform resynchronization. + This parameter can be a value of @ref CAN_synchronisation_jump_width */ + + uint32_t TimeSeg1; /*!< Specifies the number of time quanta in Bit Segment 1. + This parameter can be a value of @ref CAN_time_quantum_in_bit_segment_1 */ + + uint32_t TimeSeg2; /*!< Specifies the number of time quanta in Bit Segment 2. + This parameter can be a value of @ref CAN_time_quantum_in_bit_segment_2 */ + + FunctionalState TimeTriggeredMode; /*!< Enable or disable the time triggered communication mode. + This parameter can be set to ENABLE or DISABLE. */ + + FunctionalState AutoBusOff; /*!< Enable or disable the automatic bus-off management. + This parameter can be set to ENABLE or DISABLE. */ + + FunctionalState AutoWakeUp; /*!< Enable or disable the automatic wake-up mode. + This parameter can be set to ENABLE or DISABLE. */ + + FunctionalState AutoRetransmission; /*!< Enable or disable the non-automatic retransmission mode. + This parameter can be set to ENABLE or DISABLE. */ + + FunctionalState ReceiveFifoLocked; /*!< Enable or disable the Receive FIFO Locked mode. + This parameter can be set to ENABLE or DISABLE. */ + + FunctionalState TransmitFifoPriority;/*!< Enable or disable the transmit FIFO priority. + This parameter can be set to ENABLE or DISABLE. */ + +} CAN_InitTypeDef; + +/** + * @brief CAN filter configuration structure definition + */ +typedef struct +{ + uint32_t FilterIdHigh; /*!< Specifies the filter identification number (MSBs for a 32-bit + configuration, first one for a 16-bit configuration). + This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF. */ + + uint32_t FilterIdLow; /*!< Specifies the filter identification number (LSBs for a 32-bit + configuration, second one for a 16-bit configuration). + This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF. */ + + uint32_t FilterMaskIdHigh; /*!< Specifies the filter mask number or identification number, + according to the mode (MSBs for a 32-bit configuration, + first one for a 16-bit configuration). + This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF. */ + + uint32_t FilterMaskIdLow; /*!< Specifies the filter mask number or identification number, + according to the mode (LSBs for a 32-bit configuration, + second one for a 16-bit configuration). + This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF. */ + + uint32_t FilterFIFOAssignment; /*!< Specifies the FIFO (0 or 1U) which will be assigned to the filter. + This parameter can be a value of @ref CAN_filter_FIFO */ + + uint32_t FilterBank; /*!< Specifies the filter bank which will be initialized. + For single CAN instance(14 dedicated filter banks), + this parameter must be a number between Min_Data = 0 and Max_Data = 13. + For dual CAN instances(28 filter banks shared), + this parameter must be a number between Min_Data = 0 and Max_Data = 27. */ + + uint32_t FilterMode; /*!< Specifies the filter mode to be initialized. + This parameter can be a value of @ref CAN_filter_mode */ + + uint32_t FilterScale; /*!< Specifies the filter scale. + This parameter can be a value of @ref CAN_filter_scale */ + + uint32_t FilterActivation; /*!< Enable or disable the filter. + This parameter can be a value of @ref CAN_filter_activation */ + + uint32_t SlaveStartFilterBank; /*!< Select the start filter bank for the slave CAN instance. + For single CAN instances, this parameter is meaningless. + For dual CAN instances, all filter banks with lower index are assigned to master + CAN instance, whereas all filter banks with greater index are assigned to slave + CAN instance. + This parameter must be a number between Min_Data = 0 and Max_Data = 27. */ + +} CAN_FilterTypeDef; + +/** + * @brief CAN Tx message header structure definition + */ +typedef struct +{ + uint32_t StdId; /*!< Specifies the standard identifier. + This parameter must be a number between Min_Data = 0 and Max_Data = 0x7FF. */ + + uint32_t ExtId; /*!< Specifies the extended identifier. + This parameter must be a number between Min_Data = 0 and Max_Data = 0x1FFFFFFF. */ + + uint32_t IDE; /*!< Specifies the type of identifier for the message that will be transmitted. + This parameter can be a value of @ref CAN_identifier_type */ + + uint32_t RTR; /*!< Specifies the type of frame for the message that will be transmitted. + This parameter can be a value of @ref CAN_remote_transmission_request */ + + uint32_t DLC; /*!< Specifies the length of the frame that will be transmitted. + This parameter must be a number between Min_Data = 0 and Max_Data = 8. */ + + FunctionalState TransmitGlobalTime; /*!< Specifies whether the timestamp counter value captured on start + of frame transmission, is sent in DATA6 and DATA7 replacing pData[6] and pData[7]. + @note: Time Triggered Communication Mode must be enabled. + @note: DLC must be programmed as 8 bytes, in order these 2 bytes are sent. + This parameter can be set to ENABLE or DISABLE. */ + +} CAN_TxHeaderTypeDef; + +/** + * @brief CAN Rx message header structure definition + */ +typedef struct +{ + uint32_t StdId; /*!< Specifies the standard identifier. + This parameter must be a number between Min_Data = 0 and Max_Data = 0x7FF. */ + + uint32_t ExtId; /*!< Specifies the extended identifier. + This parameter must be a number between Min_Data = 0 and Max_Data = 0x1FFFFFFF. */ + + uint32_t IDE; /*!< Specifies the type of identifier for the message that will be transmitted. + This parameter can be a value of @ref CAN_identifier_type */ + + uint32_t RTR; /*!< Specifies the type of frame for the message that will be transmitted. + This parameter can be a value of @ref CAN_remote_transmission_request */ + + uint32_t DLC; /*!< Specifies the length of the frame that will be transmitted. + This parameter must be a number between Min_Data = 0 and Max_Data = 8. */ + + uint32_t Timestamp; /*!< Specifies the timestamp counter value captured on start of frame reception. + @note: Time Triggered Communication Mode must be enabled. + This parameter must be a number between Min_Data = 0 and Max_Data = 0xFFFF. */ + + uint32_t FilterMatchIndex; /*!< Specifies the index of matching acceptance filter element. + This parameter must be a number between Min_Data = 0 and Max_Data = 0xFF. */ + +} CAN_RxHeaderTypeDef; + +/** + * @brief CAN handle Structure definition + */ +typedef struct __CAN_HandleTypeDef +{ + CAN_TypeDef* Instance; /*!< Register base address */ + + CAN_InitTypeDef Init; /*!< CAN required parameters */ + + __IO HAL_CAN_StateTypeDef State; /*!< CAN communication state */ + + __IO uint32_t ErrorCode; /*!< CAN Error code. + This parameter can be a value of @ref CAN_Error_Code */ + +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + void (* TxMailbox0CompleteCallback)(struct __CAN_HandleTypeDef* hcan);/*!< CAN Tx Mailbox 0 complete callback */ + void (* TxMailbox1CompleteCallback)(struct __CAN_HandleTypeDef* hcan);/*!< CAN Tx Mailbox 1 complete callback */ + void (* TxMailbox2CompleteCallback)(struct __CAN_HandleTypeDef* hcan);/*!< CAN Tx Mailbox 2 complete callback */ + void (* TxMailbox0AbortCallback)(struct __CAN_HandleTypeDef* hcan); /*!< CAN Tx Mailbox 0 abort callback */ + void (* TxMailbox1AbortCallback)(struct __CAN_HandleTypeDef* hcan); /*!< CAN Tx Mailbox 1 abort callback */ + void (* TxMailbox2AbortCallback)(struct __CAN_HandleTypeDef* hcan); /*!< CAN Tx Mailbox 2 abort callback */ + void (* RxFifo0MsgPendingCallback)(struct __CAN_HandleTypeDef* hcan); /*!< CAN Rx FIFO 0 msg pending callback */ + void (* RxFifo0FullCallback)(struct __CAN_HandleTypeDef* hcan); /*!< CAN Rx FIFO 0 full callback */ + void (* RxFifo1MsgPendingCallback)(struct __CAN_HandleTypeDef* hcan); /*!< CAN Rx FIFO 1 msg pending callback */ + void (* RxFifo1FullCallback)(struct __CAN_HandleTypeDef* hcan); /*!< CAN Rx FIFO 1 full callback */ + void (* SleepCallback)(struct __CAN_HandleTypeDef* hcan); /*!< CAN Sleep callback */ + void (* WakeUpFromRxMsgCallback)(struct __CAN_HandleTypeDef* hcan); /*!< CAN Wake Up from Rx msg callback */ + void (* ErrorCallback)(struct __CAN_HandleTypeDef* hcan); /*!< CAN Error callback */ + + void (* MspInitCallback)(struct __CAN_HandleTypeDef* hcan); /*!< CAN Msp Init callback */ + void (* MspDeInitCallback)(struct __CAN_HandleTypeDef* hcan); /*!< CAN Msp DeInit callback */ + +#endif /* (USE_HAL_CAN_REGISTER_CALLBACKS) */ +} CAN_HandleTypeDef; + +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 +/** + * @brief HAL CAN common Callback ID enumeration definition + */ +typedef enum +{ + HAL_CAN_TX_MAILBOX0_COMPLETE_CB_ID = 0x00U, /*!< CAN Tx Mailbox 0 complete callback ID */ + HAL_CAN_TX_MAILBOX1_COMPLETE_CB_ID = 0x01U, /*!< CAN Tx Mailbox 1 complete callback ID */ + HAL_CAN_TX_MAILBOX2_COMPLETE_CB_ID = 0x02U, /*!< CAN Tx Mailbox 2 complete callback ID */ + HAL_CAN_TX_MAILBOX0_ABORT_CB_ID = 0x03U, /*!< CAN Tx Mailbox 0 abort callback ID */ + HAL_CAN_TX_MAILBOX1_ABORT_CB_ID = 0x04U, /*!< CAN Tx Mailbox 1 abort callback ID */ + HAL_CAN_TX_MAILBOX2_ABORT_CB_ID = 0x05U, /*!< CAN Tx Mailbox 2 abort callback ID */ + HAL_CAN_RX_FIFO0_MSG_PENDING_CB_ID = 0x06U, /*!< CAN Rx FIFO 0 message pending callback ID */ + HAL_CAN_RX_FIFO0_FULL_CB_ID = 0x07U, /*!< CAN Rx FIFO 0 full callback ID */ + HAL_CAN_RX_FIFO1_MSG_PENDING_CB_ID = 0x08U, /*!< CAN Rx FIFO 1 message pending callback ID */ + HAL_CAN_RX_FIFO1_FULL_CB_ID = 0x09U, /*!< CAN Rx FIFO 1 full callback ID */ + HAL_CAN_SLEEP_CB_ID = 0x0AU, /*!< CAN Sleep callback ID */ + HAL_CAN_WAKEUP_FROM_RX_MSG_CB_ID = 0x0BU, /*!< CAN Wake Up fropm Rx msg callback ID */ + HAL_CAN_ERROR_CB_ID = 0x0CU, /*!< CAN Error callback ID */ + + HAL_CAN_MSPINIT_CB_ID = 0x0DU, /*!< CAN MspInit callback ID */ + HAL_CAN_MSPDEINIT_CB_ID = 0x0EU, /*!< CAN MspDeInit callback ID */ + +} HAL_CAN_CallbackIDTypeDef; + +/** + * @brief HAL CAN Callback pointer definition + */ +typedef void (*pCAN_CallbackTypeDef)(CAN_HandleTypeDef* hcan); /*!< pointer to a CAN callback function */ + +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ + +/** @defgroup CAN_Exported_Constants CAN Exported Constants + * @{ + */ + +/** @defgroup CAN_Error_Code CAN Error Code + * @{ + */ +#define HAL_CAN_ERROR_NONE (0x00000000U) /*!< No error */ +#define HAL_CAN_ERROR_EWG (0x00000001U) /*!< Protocol Error Warning */ +#define HAL_CAN_ERROR_EPV (0x00000002U) /*!< Error Passive */ +#define HAL_CAN_ERROR_BOF (0x00000004U) /*!< Bus-off error */ +#define HAL_CAN_ERROR_STF (0x00000008U) /*!< Stuff error */ +#define HAL_CAN_ERROR_FOR (0x00000010U) /*!< Form error */ +#define HAL_CAN_ERROR_ACK (0x00000020U) /*!< Acknowledgment error */ +#define HAL_CAN_ERROR_BR (0x00000040U) /*!< Bit recessive error */ +#define HAL_CAN_ERROR_BD (0x00000080U) /*!< Bit dominant error */ +#define HAL_CAN_ERROR_CRC (0x00000100U) /*!< CRC error */ +#define HAL_CAN_ERROR_RX_FOV0 (0x00000200U) /*!< Rx FIFO0 overrun error */ +#define HAL_CAN_ERROR_RX_FOV1 (0x00000400U) /*!< Rx FIFO1 overrun error */ +#define HAL_CAN_ERROR_TX_ALST0 (0x00000800U) /*!< TxMailbox 0 transmit failure due to arbitration lost */ +#define HAL_CAN_ERROR_TX_TERR0 (0x00001000U) /*!< TxMailbox 1 transmit failure due to tranmit error */ +#define HAL_CAN_ERROR_TX_ALST1 (0x00002000U) /*!< TxMailbox 0 transmit failure due to arbitration lost */ +#define HAL_CAN_ERROR_TX_TERR1 (0x00004000U) /*!< TxMailbox 1 transmit failure due to tranmit error */ +#define HAL_CAN_ERROR_TX_ALST2 (0x00008000U) /*!< TxMailbox 0 transmit failure due to arbitration lost */ +#define HAL_CAN_ERROR_TX_TERR2 (0x00010000U) /*!< TxMailbox 1 transmit failure due to tranmit error */ +#define HAL_CAN_ERROR_TIMEOUT (0x00020000U) /*!< Timeout error */ +#define HAL_CAN_ERROR_NOT_INITIALIZED (0x00040000U) /*!< Peripheral not initialized */ +#define HAL_CAN_ERROR_NOT_READY (0x00080000U) /*!< Peripheral not ready */ +#define HAL_CAN_ERROR_NOT_STARTED (0x00100000U) /*!< Peripheral not started */ +#define HAL_CAN_ERROR_PARAM (0x00200000U) /*!< Parameter error */ + +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 +#define HAL_CAN_ERROR_INVALID_CALLBACK (0x00400000U) /*!< Invalid Callback error */ +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ +#define HAL_CAN_ERROR_INTERNAL (0x00800000U) /*!< Internal error */ + +/** + * @} + */ + +/** @defgroup CAN_InitStatus CAN InitStatus + * @{ + */ +#define CAN_INITSTATUS_FAILED (0x00000000U) /*!< CAN initialization failed */ +#define CAN_INITSTATUS_SUCCESS (0x00000001U) /*!< CAN initialization OK */ +/** + * @} + */ + +/** @defgroup CAN_operating_mode CAN Operating Mode + * @{ + */ +#define CAN_MODE_NORMAL (0x00000000U) /*!< Normal mode */ +#define CAN_MODE_LOOPBACK ((uint32_t)CAN_BTR_LBKM) /*!< Loopback mode */ +#define CAN_MODE_SILENT ((uint32_t)CAN_BTR_SILM) /*!< Silent mode */ +#define CAN_MODE_SILENT_LOOPBACK ((uint32_t)(CAN_BTR_LBKM | CAN_BTR_SILM)) /*!< Loopback combined with silent mode */ +/** + * @} + */ + + +/** @defgroup CAN_synchronisation_jump_width CAN Synchronization Jump Width + * @{ + */ +#define CAN_SJW_1TQ (0x00000000U) /*!< 1 time quantum */ +#define CAN_SJW_2TQ ((uint32_t)CAN_BTR_SJW_0) /*!< 2 time quantum */ +#define CAN_SJW_3TQ ((uint32_t)CAN_BTR_SJW_1) /*!< 3 time quantum */ +#define CAN_SJW_4TQ ((uint32_t)CAN_BTR_SJW) /*!< 4 time quantum */ +/** + * @} + */ + +/** @defgroup CAN_time_quantum_in_bit_segment_1 CAN Time Quantum in Bit Segment 1 + * @{ + */ +#define CAN_BS1_1TQ (0x00000000U) /*!< 1 time quantum */ +#define CAN_BS1_2TQ ((uint32_t)CAN_BTR_TS1_0) /*!< 2 time quantum */ +#define CAN_BS1_3TQ ((uint32_t)CAN_BTR_TS1_1) /*!< 3 time quantum */ +#define CAN_BS1_4TQ ((uint32_t)(CAN_BTR_TS1_1 | CAN_BTR_TS1_0)) /*!< 4 time quantum */ +#define CAN_BS1_5TQ ((uint32_t)CAN_BTR_TS1_2) /*!< 5 time quantum */ +#define CAN_BS1_6TQ ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_0)) /*!< 6 time quantum */ +#define CAN_BS1_7TQ ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_1)) /*!< 7 time quantum */ +#define CAN_BS1_8TQ ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_1 | CAN_BTR_TS1_0)) /*!< 8 time quantum */ +#define CAN_BS1_9TQ ((uint32_t)CAN_BTR_TS1_3) /*!< 9 time quantum */ +#define CAN_BS1_10TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_0)) /*!< 10 time quantum */ +#define CAN_BS1_11TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_1)) /*!< 11 time quantum */ +#define CAN_BS1_12TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_1 | CAN_BTR_TS1_0)) /*!< 12 time quantum */ +#define CAN_BS1_13TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2)) /*!< 13 time quantum */ +#define CAN_BS1_14TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2 | CAN_BTR_TS1_0)) /*!< 14 time quantum */ +#define CAN_BS1_15TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2 | CAN_BTR_TS1_1)) /*!< 15 time quantum */ +#define CAN_BS1_16TQ ((uint32_t)CAN_BTR_TS1) /*!< 16 time quantum */ +/** + * @} + */ + +/** @defgroup CAN_time_quantum_in_bit_segment_2 CAN Time Quantum in Bit Segment 2 + * @{ + */ +#define CAN_BS2_1TQ (0x00000000U) /*!< 1 time quantum */ +#define CAN_BS2_2TQ ((uint32_t)CAN_BTR_TS2_0) /*!< 2 time quantum */ +#define CAN_BS2_3TQ ((uint32_t)CAN_BTR_TS2_1) /*!< 3 time quantum */ +#define CAN_BS2_4TQ ((uint32_t)(CAN_BTR_TS2_1 | CAN_BTR_TS2_0)) /*!< 4 time quantum */ +#define CAN_BS2_5TQ ((uint32_t)CAN_BTR_TS2_2) /*!< 5 time quantum */ +#define CAN_BS2_6TQ ((uint32_t)(CAN_BTR_TS2_2 | CAN_BTR_TS2_0)) /*!< 6 time quantum */ +#define CAN_BS2_7TQ ((uint32_t)(CAN_BTR_TS2_2 | CAN_BTR_TS2_1)) /*!< 7 time quantum */ +#define CAN_BS2_8TQ ((uint32_t)CAN_BTR_TS2) /*!< 8 time quantum */ +/** + * @} + */ + +/** @defgroup CAN_filter_mode CAN Filter Mode + * @{ + */ +#define CAN_FILTERMODE_IDMASK (0x00000000U) /*!< Identifier mask mode */ +#define CAN_FILTERMODE_IDLIST (0x00000001U) /*!< Identifier list mode */ +/** + * @} + */ + +/** @defgroup CAN_filter_scale CAN Filter Scale + * @{ + */ +#define CAN_FILTERSCALE_16BIT (0x00000000U) /*!< Two 16-bit filters */ +#define CAN_FILTERSCALE_32BIT (0x00000001U) /*!< One 32-bit filter */ +/** + * @} + */ + +/** @defgroup CAN_filter_activation CAN Filter Activation + * @{ + */ +#define CAN_FILTER_DISABLE (0x00000000U) /*!< Disable filter */ +#define CAN_FILTER_ENABLE (0x00000001U) /*!< Enable filter */ +/** + * @} + */ + +/** @defgroup CAN_filter_FIFO CAN Filter FIFO + * @{ + */ +#define CAN_FILTER_FIFO0 (0x00000000U) /*!< Filter FIFO 0 assignment for filter x */ +#define CAN_FILTER_FIFO1 (0x00000001U) /*!< Filter FIFO 1 assignment for filter x */ +/** + * @} + */ + +/** @defgroup CAN_identifier_type CAN Identifier Type + * @{ + */ +#define CAN_ID_STD (0x00000000U) /*!< Standard Id */ +#define CAN_ID_EXT (0x00000004U) /*!< Extended Id */ +/** + * @} + */ + +/** @defgroup CAN_remote_transmission_request CAN Remote Transmission Request + * @{ + */ +#define CAN_RTR_DATA (0x00000000U) /*!< Data frame */ +#define CAN_RTR_REMOTE (0x00000002U) /*!< Remote frame */ +/** + * @} + */ + +/** @defgroup CAN_receive_FIFO_number CAN Receive FIFO Number + * @{ + */ +#define CAN_RX_FIFO0 (0x00000000U) /*!< CAN receive FIFO 0 */ +#define CAN_RX_FIFO1 (0x00000001U) /*!< CAN receive FIFO 1 */ +/** + * @} + */ + +/** @defgroup CAN_Tx_Mailboxes CAN Tx Mailboxes + * @{ + */ +#define CAN_TX_MAILBOX0 (0x00000001U) /*!< Tx Mailbox 0 */ +#define CAN_TX_MAILBOX1 (0x00000002U) /*!< Tx Mailbox 1 */ +#define CAN_TX_MAILBOX2 (0x00000004U) /*!< Tx Mailbox 2 */ +/** + * @} + */ + +/** @defgroup CAN_flags CAN Flags + * @{ + */ +/* Transmit Flags */ +#define CAN_FLAG_RQCP0 (0x00000500U) /*!< Request complete MailBox 0 flag */ +#define CAN_FLAG_TXOK0 (0x00000501U) /*!< Transmission OK MailBox 0 flag */ +#define CAN_FLAG_ALST0 (0x00000502U) /*!< Arbitration Lost MailBox 0 flag */ +#define CAN_FLAG_TERR0 (0x00000503U) /*!< Transmission error MailBox 0 flag */ +#define CAN_FLAG_RQCP1 (0x00000508U) /*!< Request complete MailBox1 flag */ +#define CAN_FLAG_TXOK1 (0x00000509U) /*!< Transmission OK MailBox 1 flag */ +#define CAN_FLAG_ALST1 (0x0000050AU) /*!< Arbitration Lost MailBox 1 flag */ +#define CAN_FLAG_TERR1 (0x0000050BU) /*!< Transmission error MailBox 1 flag */ +#define CAN_FLAG_RQCP2 (0x00000510U) /*!< Request complete MailBox2 flag */ +#define CAN_FLAG_TXOK2 (0x00000511U) /*!< Transmission OK MailBox 2 flag */ +#define CAN_FLAG_ALST2 (0x00000512U) /*!< Arbitration Lost MailBox 2 flag */ +#define CAN_FLAG_TERR2 (0x00000513U) /*!< Transmission error MailBox 2 flag */ +#define CAN_FLAG_TME0 (0x0000051AU) /*!< Transmit mailbox 0 empty flag */ +#define CAN_FLAG_TME1 (0x0000051BU) /*!< Transmit mailbox 1 empty flag */ +#define CAN_FLAG_TME2 (0x0000051CU) /*!< Transmit mailbox 2 empty flag */ +#define CAN_FLAG_LOW0 (0x0000051DU) /*!< Lowest priority mailbox 0 flag */ +#define CAN_FLAG_LOW1 (0x0000051EU) /*!< Lowest priority mailbox 1 flag */ +#define CAN_FLAG_LOW2 (0x0000051FU) /*!< Lowest priority mailbox 2 flag */ + +/* Receive Flags */ +#define CAN_FLAG_FF0 (0x00000203U) /*!< RX FIFO 0 Full flag */ +#define CAN_FLAG_FOV0 (0x00000204U) /*!< RX FIFO 0 Overrun flag */ +#define CAN_FLAG_FF1 (0x00000403U) /*!< RX FIFO 1 Full flag */ +#define CAN_FLAG_FOV1 (0x00000404U) /*!< RX FIFO 1 Overrun flag */ + +/* Operating Mode Flags */ +#define CAN_FLAG_INAK (0x00000100U) /*!< Initialization acknowledge flag */ +#define CAN_FLAG_SLAK (0x00000101U) /*!< Sleep acknowledge flag */ +#define CAN_FLAG_ERRI (0x00000102U) /*!< Error flag */ +#define CAN_FLAG_WKU (0x00000103U) /*!< Wake up interrupt flag */ +#define CAN_FLAG_SLAKI (0x00000104U) /*!< Sleep acknowledge interrupt flag */ + +/* Error Flags */ +#define CAN_FLAG_EWG (0x00000300U) /*!< Error warning flag */ +#define CAN_FLAG_EPV (0x00000301U) /*!< Error passive flag */ +#define CAN_FLAG_BOF (0x00000302U) /*!< Bus-Off flag */ +/** + * @} + */ + + +/** @defgroup CAN_Interrupts CAN Interrupts + * @{ + */ +/* Transmit Interrupt */ +#define CAN_IT_TX_MAILBOX_EMPTY ((uint32_t)CAN_IER_TMEIE) /*!< Transmit mailbox empty interrupt */ + +/* Receive Interrupts */ +#define CAN_IT_RX_FIFO0_MSG_PENDING ((uint32_t)CAN_IER_FMPIE0) /*!< FIFO 0 message pending interrupt */ +#define CAN_IT_RX_FIFO0_FULL ((uint32_t)CAN_IER_FFIE0) /*!< FIFO 0 full interrupt */ +#define CAN_IT_RX_FIFO0_OVERRUN ((uint32_t)CAN_IER_FOVIE0) /*!< FIFO 0 overrun interrupt */ +#define CAN_IT_RX_FIFO1_MSG_PENDING ((uint32_t)CAN_IER_FMPIE1) /*!< FIFO 1 message pending interrupt */ +#define CAN_IT_RX_FIFO1_FULL ((uint32_t)CAN_IER_FFIE1) /*!< FIFO 1 full interrupt */ +#define CAN_IT_RX_FIFO1_OVERRUN ((uint32_t)CAN_IER_FOVIE1) /*!< FIFO 1 overrun interrupt */ + +/* Operating Mode Interrupts */ +#define CAN_IT_WAKEUP ((uint32_t)CAN_IER_WKUIE) /*!< Wake-up interrupt */ +#define CAN_IT_SLEEP_ACK ((uint32_t)CAN_IER_SLKIE) /*!< Sleep acknowledge interrupt */ + +/* Error Interrupts */ +#define CAN_IT_ERROR_WARNING ((uint32_t)CAN_IER_EWGIE) /*!< Error warning interrupt */ +#define CAN_IT_ERROR_PASSIVE ((uint32_t)CAN_IER_EPVIE) /*!< Error passive interrupt */ +#define CAN_IT_BUSOFF ((uint32_t)CAN_IER_BOFIE) /*!< Bus-off interrupt */ +#define CAN_IT_LAST_ERROR_CODE ((uint32_t)CAN_IER_LECIE) /*!< Last error code interrupt */ +#define CAN_IT_ERROR ((uint32_t)CAN_IER_ERRIE) /*!< Error Interrupt */ +/** + * @} + */ + +/** + * @} + */ + +/* Exported macros -----------------------------------------------------------*/ +/** @defgroup CAN_Exported_Macros CAN Exported Macros + * @{ + */ + +/** @brief Reset CAN handle state + * @param __HANDLE__ CAN handle. + * @retval None + */ +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 +#define __HAL_CAN_RESET_HANDLE_STATE(__HANDLE__) do{ \ + (__HANDLE__)->State = HAL_CAN_STATE_RESET; \ + (__HANDLE__)->MspInitCallback = NULL; \ + (__HANDLE__)->MspDeInitCallback = NULL; \ + } while(0) +#else +#define __HAL_CAN_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_CAN_STATE_RESET) +#endif /*USE_HAL_CAN_REGISTER_CALLBACKS */ + +/** + * @brief Enable the specified CAN interrupts. + * @param __HANDLE__ CAN handle. + * @param __INTERRUPT__ CAN Interrupt sources to enable. + * This parameter can be any combination of @arg CAN_Interrupts + * @retval None + */ +#define __HAL_CAN_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->IER) |= (__INTERRUPT__)) + +/** + * @brief Disable the specified CAN interrupts. + * @param __HANDLE__ CAN handle. + * @param __INTERRUPT__ CAN Interrupt sources to disable. + * This parameter can be any combination of @arg CAN_Interrupts + * @retval None + */ +#define __HAL_CAN_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->IER) &= ~(__INTERRUPT__)) + +/** @brief Check if the specified CAN interrupt source is enabled or disabled. + * @param __HANDLE__ specifies the CAN Handle. + * @param __INTERRUPT__ specifies the CAN interrupt source to check. + * This parameter can be a value of @arg CAN_Interrupts + * @retval The state of __IT__ (TRUE or FALSE). + */ +#define __HAL_CAN_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->IER) & (__INTERRUPT__)) + +/** @brief Check whether the specified CAN flag is set or not. + * @param __HANDLE__ specifies the CAN Handle. + * @param __FLAG__ specifies the flag to check. + * This parameter can be one of @arg CAN_flags + * @retval The state of __FLAG__ (TRUE or FALSE). + */ +#define __HAL_CAN_GET_FLAG(__HANDLE__, __FLAG__) \ + ((((__FLAG__) >> 8U) == 5U)? ((((__HANDLE__)->Instance->TSR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ + (((__FLAG__) >> 8U) == 2U)? ((((__HANDLE__)->Instance->RF0R) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ + (((__FLAG__) >> 8U) == 4U)? ((((__HANDLE__)->Instance->RF1R) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ + (((__FLAG__) >> 8U) == 1U)? ((((__HANDLE__)->Instance->MSR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ + (((__FLAG__) >> 8U) == 3U)? ((((__HANDLE__)->Instance->ESR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): 0U) + +/** @brief Clear the specified CAN pending flag. + * @param __HANDLE__ specifies the CAN Handle. + * @param __FLAG__ specifies the flag to check. + * This parameter can be one of the following values: + * @arg CAN_FLAG_RQCP0: Request complete MailBox 0 Flag + * @arg CAN_FLAG_TXOK0: Transmission OK MailBox 0 Flag + * @arg CAN_FLAG_ALST0: Arbitration Lost MailBox 0 Flag + * @arg CAN_FLAG_TERR0: Transmission error MailBox 0 Flag + * @arg CAN_FLAG_RQCP1: Request complete MailBox 1 Flag + * @arg CAN_FLAG_TXOK1: Transmission OK MailBox 1 Flag + * @arg CAN_FLAG_ALST1: Arbitration Lost MailBox 1 Flag + * @arg CAN_FLAG_TERR1: Transmission error MailBox 1 Flag + * @arg CAN_FLAG_RQCP2: Request complete MailBox 2 Flag + * @arg CAN_FLAG_TXOK2: Transmission OK MailBox 2 Flag + * @arg CAN_FLAG_ALST2: Arbitration Lost MailBox 2 Flag + * @arg CAN_FLAG_TERR2: Transmission error MailBox 2 Flag + * @arg CAN_FLAG_FF0: RX FIFO 0 Full Flag + * @arg CAN_FLAG_FOV0: RX FIFO 0 Overrun Flag + * @arg CAN_FLAG_FF1: RX FIFO 1 Full Flag + * @arg CAN_FLAG_FOV1: RX FIFO 1 Overrun Flag + * @arg CAN_FLAG_WKUI: Wake up Interrupt Flag + * @arg CAN_FLAG_SLAKI: Sleep acknowledge Interrupt Flag + * @retval None + */ +#define __HAL_CAN_CLEAR_FLAG(__HANDLE__, __FLAG__) \ + ((((__FLAG__) >> 8U) == 5U)? (((__HANDLE__)->Instance->TSR) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ + (((__FLAG__) >> 8U) == 2U)? (((__HANDLE__)->Instance->RF0R) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ + (((__FLAG__) >> 8U) == 4U)? (((__HANDLE__)->Instance->RF1R) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ + (((__FLAG__) >> 8U) == 1U)? (((__HANDLE__)->Instance->MSR) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): 0U) + +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup CAN_Exported_Functions CAN Exported Functions + * @{ + */ + +/** @addtogroup CAN_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * @{ + */ + +/* Initialization and de-initialization functions *****************************/ +HAL_StatusTypeDef HAL_CAN_Init(CAN_HandleTypeDef* hcan); +HAL_StatusTypeDef HAL_CAN_DeInit(CAN_HandleTypeDef* hcan); +void HAL_CAN_MspInit(CAN_HandleTypeDef* hcan); +void HAL_CAN_MspDeInit(CAN_HandleTypeDef* hcan); + +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 +/* Callbacks Register/UnRegister functions ***********************************/ +HAL_StatusTypeDef HAL_CAN_RegisterCallback(CAN_HandleTypeDef* hcan, HAL_CAN_CallbackIDTypeDef CallbackID, void (* pCallback)(CAN_HandleTypeDef* _hcan)); +HAL_StatusTypeDef HAL_CAN_UnRegisterCallback(CAN_HandleTypeDef* hcan, HAL_CAN_CallbackIDTypeDef CallbackID); + +#endif /* (USE_HAL_CAN_REGISTER_CALLBACKS) */ +/** + * @} + */ + +/** @addtogroup CAN_Exported_Functions_Group2 Configuration functions + * @brief Configuration functions + * @{ + */ + +/* Configuration functions ****************************************************/ +HAL_StatusTypeDef HAL_CAN_ConfigFilter(CAN_HandleTypeDef* hcan, CAN_FilterTypeDef* sFilterConfig); + +/** + * @} + */ + +/** @addtogroup CAN_Exported_Functions_Group3 Control functions + * @brief Control functions + * @{ + */ + +/* Control functions **********************************************************/ +HAL_StatusTypeDef HAL_CAN_Start(CAN_HandleTypeDef* hcan); +HAL_StatusTypeDef HAL_CAN_Stop(CAN_HandleTypeDef* hcan); +HAL_StatusTypeDef HAL_CAN_RequestSleep(CAN_HandleTypeDef* hcan); +HAL_StatusTypeDef HAL_CAN_WakeUp(CAN_HandleTypeDef* hcan); +uint32_t HAL_CAN_IsSleepActive(CAN_HandleTypeDef* hcan); +HAL_StatusTypeDef HAL_CAN_AddTxMessage(CAN_HandleTypeDef* hcan, CAN_TxHeaderTypeDef* pHeader, uint8_t aData[], uint32_t* pTxMailbox); +HAL_StatusTypeDef HAL_CAN_AbortTxRequest(CAN_HandleTypeDef* hcan, uint32_t TxMailboxes); +uint32_t HAL_CAN_GetTxMailboxesFreeLevel(CAN_HandleTypeDef* hcan); +uint32_t HAL_CAN_IsTxMessagePending(CAN_HandleTypeDef* hcan, uint32_t TxMailboxes); +uint32_t HAL_CAN_GetTxTimestamp(CAN_HandleTypeDef* hcan, uint32_t TxMailbox); +HAL_StatusTypeDef HAL_CAN_GetRxMessage(CAN_HandleTypeDef* hcan, uint32_t RxFifo, CAN_RxHeaderTypeDef* pHeader, uint8_t aData[]); +uint32_t HAL_CAN_GetRxFifoFillLevel(CAN_HandleTypeDef* hcan, uint32_t RxFifo); + +/** + * @} + */ + +/** @addtogroup CAN_Exported_Functions_Group4 Interrupts management + * @brief Interrupts management + * @{ + */ +/* Interrupts management ******************************************************/ +HAL_StatusTypeDef HAL_CAN_ActivateNotification(CAN_HandleTypeDef* hcan, uint32_t ActiveITs); +HAL_StatusTypeDef HAL_CAN_DeactivateNotification(CAN_HandleTypeDef* hcan, uint32_t InactiveITs); +void HAL_CAN_IRQHandler(CAN_HandleTypeDef* hcan); + +/** + * @} + */ + +/** @addtogroup CAN_Exported_Functions_Group5 Callback functions + * @brief Callback functions + * @{ + */ +/* Callbacks functions ********************************************************/ + +void HAL_CAN_TxMailbox0CompleteCallback(CAN_HandleTypeDef* hcan); +void HAL_CAN_TxMailbox1CompleteCallback(CAN_HandleTypeDef* hcan); +void HAL_CAN_TxMailbox2CompleteCallback(CAN_HandleTypeDef* hcan); +void HAL_CAN_TxMailbox0AbortCallback(CAN_HandleTypeDef* hcan); +void HAL_CAN_TxMailbox1AbortCallback(CAN_HandleTypeDef* hcan); +void HAL_CAN_TxMailbox2AbortCallback(CAN_HandleTypeDef* hcan); +void HAL_CAN_RxFifo0MsgPendingCallback(CAN_HandleTypeDef* hcan); +void HAL_CAN_RxFifo0FullCallback(CAN_HandleTypeDef* hcan); +void HAL_CAN_RxFifo1MsgPendingCallback(CAN_HandleTypeDef* hcan); +void HAL_CAN_RxFifo1FullCallback(CAN_HandleTypeDef* hcan); +void HAL_CAN_SleepCallback(CAN_HandleTypeDef* hcan); +void HAL_CAN_WakeUpFromRxMsgCallback(CAN_HandleTypeDef* hcan); +void HAL_CAN_ErrorCallback(CAN_HandleTypeDef* hcan); + +/** + * @} + */ + +/** @addtogroup CAN_Exported_Functions_Group6 Peripheral State and Error functions + * @brief CAN Peripheral State functions + * @{ + */ +/* Peripheral State and Error functions ***************************************/ +HAL_CAN_StateTypeDef HAL_CAN_GetState(CAN_HandleTypeDef* hcan); +uint32_t HAL_CAN_GetError(CAN_HandleTypeDef* hcan); +HAL_StatusTypeDef HAL_CAN_ResetError(CAN_HandleTypeDef* hcan); + +/** + * @} + */ + +/** + * @} + */ + +/* Private types -------------------------------------------------------------*/ +/** @defgroup CAN_Private_Types CAN Private Types + * @{ + */ + +/** + * @} + */ + +/* Private variables ---------------------------------------------------------*/ +/** @defgroup CAN_Private_Variables CAN Private Variables + * @{ + */ + +/** + * @} + */ + +/* Private constants ---------------------------------------------------------*/ +/** @defgroup CAN_Private_Constants CAN Private Constants + * @{ + */ +#define CAN_FLAG_MASK (0x000000FFU) +/** + * @} + */ + +/* Private Macros -----------------------------------------------------------*/ +/** @defgroup CAN_Private_Macros CAN Private Macros + * @{ + */ + +#define IS_CAN_MODE(MODE) (((MODE) == CAN_MODE_NORMAL) || \ + ((MODE) == CAN_MODE_LOOPBACK)|| \ + ((MODE) == CAN_MODE_SILENT) || \ + ((MODE) == CAN_MODE_SILENT_LOOPBACK)) +#define IS_CAN_SJW(SJW) (((SJW) == CAN_SJW_1TQ) || ((SJW) == CAN_SJW_2TQ) || \ + ((SJW) == CAN_SJW_3TQ) || ((SJW) == CAN_SJW_4TQ)) +#define IS_CAN_BS1(BS1) (((BS1) == CAN_BS1_1TQ) || ((BS1) == CAN_BS1_2TQ) || \ + ((BS1) == CAN_BS1_3TQ) || ((BS1) == CAN_BS1_4TQ) || \ + ((BS1) == CAN_BS1_5TQ) || ((BS1) == CAN_BS1_6TQ) || \ + ((BS1) == CAN_BS1_7TQ) || ((BS1) == CAN_BS1_8TQ) || \ + ((BS1) == CAN_BS1_9TQ) || ((BS1) == CAN_BS1_10TQ)|| \ + ((BS1) == CAN_BS1_11TQ)|| ((BS1) == CAN_BS1_12TQ)|| \ + ((BS1) == CAN_BS1_13TQ)|| ((BS1) == CAN_BS1_14TQ)|| \ + ((BS1) == CAN_BS1_15TQ)|| ((BS1) == CAN_BS1_16TQ)) +#define IS_CAN_BS2(BS2) (((BS2) == CAN_BS2_1TQ) || ((BS2) == CAN_BS2_2TQ) || \ + ((BS2) == CAN_BS2_3TQ) || ((BS2) == CAN_BS2_4TQ) || \ + ((BS2) == CAN_BS2_5TQ) || ((BS2) == CAN_BS2_6TQ) || \ + ((BS2) == CAN_BS2_7TQ) || ((BS2) == CAN_BS2_8TQ)) +#define IS_CAN_PRESCALER(PRESCALER) (((PRESCALER) >= 1U) && ((PRESCALER) <= 1024U)) +#define IS_CAN_FILTER_ID_HALFWORD(HALFWORD) ((HALFWORD) <= 0xFFFFU) +#if defined(CAN2) +#define IS_CAN_FILTER_BANK_DUAL(BANK) ((BANK) <= 27U) +#endif +#define IS_CAN_FILTER_BANK_SINGLE(BANK) ((BANK) <= 13U) +#define IS_CAN_FILTER_MODE(MODE) (((MODE) == CAN_FILTERMODE_IDMASK) || \ + ((MODE) == CAN_FILTERMODE_IDLIST)) +#define IS_CAN_FILTER_SCALE(SCALE) (((SCALE) == CAN_FILTERSCALE_16BIT) || \ + ((SCALE) == CAN_FILTERSCALE_32BIT)) +#define IS_CAN_FILTER_ACTIVATION(ACTIVATION) (((ACTIVATION) == CAN_FILTER_DISABLE) || \ + ((ACTIVATION) == CAN_FILTER_ENABLE)) +#define IS_CAN_FILTER_FIFO(FIFO) (((FIFO) == CAN_FILTER_FIFO0) || \ + ((FIFO) == CAN_FILTER_FIFO1)) +#define IS_CAN_TX_MAILBOX(TRANSMITMAILBOX) (((TRANSMITMAILBOX) == CAN_TX_MAILBOX0 ) || \ + ((TRANSMITMAILBOX) == CAN_TX_MAILBOX1 ) || \ + ((TRANSMITMAILBOX) == CAN_TX_MAILBOX2 )) +#define IS_CAN_TX_MAILBOX_LIST(TRANSMITMAILBOX) ((TRANSMITMAILBOX) <= (CAN_TX_MAILBOX0 | CAN_TX_MAILBOX1 | CAN_TX_MAILBOX2)) +#define IS_CAN_STDID(STDID) ((STDID) <= 0x7FFU) +#define IS_CAN_EXTID(EXTID) ((EXTID) <= 0x1FFFFFFFU) +#define IS_CAN_DLC(DLC) ((DLC) <= 8U) +#define IS_CAN_IDTYPE(IDTYPE) (((IDTYPE) == CAN_ID_STD) || \ + ((IDTYPE) == CAN_ID_EXT)) +#define IS_CAN_RTR(RTR) (((RTR) == CAN_RTR_DATA) || ((RTR) == CAN_RTR_REMOTE)) +#define IS_CAN_RX_FIFO(FIFO) (((FIFO) == CAN_RX_FIFO0) || ((FIFO) == CAN_RX_FIFO1)) +#define IS_CAN_IT(IT) ((IT) <= (CAN_IT_TX_MAILBOX_EMPTY | CAN_IT_RX_FIFO0_MSG_PENDING | \ + CAN_IT_RX_FIFO0_FULL | CAN_IT_RX_FIFO0_OVERRUN | \ + CAN_IT_RX_FIFO1_MSG_PENDING | CAN_IT_RX_FIFO1_FULL | \ + CAN_IT_RX_FIFO1_OVERRUN | CAN_IT_WAKEUP | \ + CAN_IT_SLEEP_ACK | CAN_IT_ERROR_WARNING | \ + CAN_IT_ERROR_PASSIVE | CAN_IT_BUSOFF | \ + CAN_IT_LAST_ERROR_CODE | CAN_IT_ERROR)) + +/** + * @} + */ +/* End of private macros -----------------------------------------------------*/ + +/** + * @} + */ + + +#endif /* CAN1 */ +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* STM32F1xx_HAL_CAN_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_cortex.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_cortex.h similarity index 63% rename from EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_cortex.h rename to EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_cortex.h index d6e75330..38d7c8eb 100644 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_cortex.h +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_cortex.h @@ -1,52 +1,34 @@ /** ****************************************************************************** - * @file stm32f4xx_hal_cortex.h + * @file stm32f1xx_hal_cortex.h * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 * @brief Header file of CORTEX HAL module. ****************************************************************************** * @attention * - *

© COPYRIGHT(c) 2016 STMicroelectronics

+ *

© Copyright (c) 2017 STMicroelectronics. + * All rights reserved.

* - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause * ****************************************************************************** */ /* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_CORTEX_H -#define __STM32F4xx_HAL_CORTEX_H +#ifndef __STM32F1xx_HAL_CORTEX_H +#define __STM32F1xx_HAL_CORTEX_H #ifdef __cplusplus extern "C" { #endif /* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_def.h" +#include "stm32f1xx_hal_def.h" -/** @addtogroup STM32F4xx_HAL_Driver +/** @addtogroup STM32F1xx_HAL_Driver * @{ */ @@ -58,7 +40,7 @@ extern "C" { * @{ */ -#if (__MPU_PRESENT == 1) +#if (__MPU_PRESENT == 1U) /** @defgroup CORTEX_MPU_Region_Initialization_Structure_definition MPU Region Initialization Structure Definition * @brief MPU Region initialization structure * @{ @@ -105,16 +87,16 @@ typedef struct /** @defgroup CORTEX_Preemption_Priority_Group CORTEX Preemption Priority Group * @{ */ -#define NVIC_PRIORITYGROUP_0 ((uint32_t)0x00000007U) /*!< 0 bits for pre-emption priority - 4 bits for subpriority */ -#define NVIC_PRIORITYGROUP_1 ((uint32_t)0x00000006U) /*!< 1 bits for pre-emption priority - 3 bits for subpriority */ -#define NVIC_PRIORITYGROUP_2 ((uint32_t)0x00000005U) /*!< 2 bits for pre-emption priority - 2 bits for subpriority */ -#define NVIC_PRIORITYGROUP_3 ((uint32_t)0x00000004U) /*!< 3 bits for pre-emption priority - 1 bits for subpriority */ -#define NVIC_PRIORITYGROUP_4 ((uint32_t)0x00000003U) /*!< 4 bits for pre-emption priority - 0 bits for subpriority */ +#define NVIC_PRIORITYGROUP_0 0x00000007U /*!< 0 bits for pre-emption priority + 4 bits for subpriority */ +#define NVIC_PRIORITYGROUP_1 0x00000006U /*!< 1 bits for pre-emption priority + 3 bits for subpriority */ +#define NVIC_PRIORITYGROUP_2 0x00000005U /*!< 2 bits for pre-emption priority + 2 bits for subpriority */ +#define NVIC_PRIORITYGROUP_3 0x00000004U /*!< 3 bits for pre-emption priority + 1 bits for subpriority */ +#define NVIC_PRIORITYGROUP_4 0x00000003U /*!< 4 bits for pre-emption priority + 0 bits for subpriority */ /** * @} */ @@ -122,8 +104,8 @@ typedef struct /** @defgroup CORTEX_SysTick_clock_source CORTEX _SysTick clock source * @{ */ -#define SYSTICK_CLKSOURCE_HCLK_DIV8 ((uint32_t)0x00000000U) -#define SYSTICK_CLKSOURCE_HCLK ((uint32_t)0x00000004U) +#define SYSTICK_CLKSOURCE_HCLK_DIV8 0x00000000U +#define SYSTICK_CLKSOURCE_HCLK 0x00000004U /** * @} @@ -133,10 +115,11 @@ typedef struct /** @defgroup CORTEX_MPU_HFNMI_PRIVDEF_Control MPU HFNMI and PRIVILEGED Access control * @{ */ -#define MPU_HFNMI_PRIVDEF_NONE ((uint32_t)0x00000000U) -#define MPU_HARDFAULT_NMI ((uint32_t)0x00000002U) -#define MPU_PRIVILEGED_DEFAULT ((uint32_t)0x00000004U) -#define MPU_HFNMI_PRIVDEF ((uint32_t)0x00000006U) +#define MPU_HFNMI_PRIVDEF_NONE 0x00000000U +#define MPU_HARDFAULT_NMI MPU_CTRL_HFNMIENA_Msk +#define MPU_PRIVILEGED_DEFAULT MPU_CTRL_PRIVDEFENA_Msk +#define MPU_HFNMI_PRIVDEF (MPU_CTRL_HFNMIENA_Msk | MPU_CTRL_PRIVDEFENA_Msk) + /** * @} */ @@ -144,8 +127,8 @@ typedef struct /** @defgroup CORTEX_MPU_Region_Enable CORTEX MPU Region Enable * @{ */ -#define MPU_REGION_ENABLE ((uint8_t)0x01U) -#define MPU_REGION_DISABLE ((uint8_t)0x00U) +#define MPU_REGION_ENABLE ((uint8_t)0x01) +#define MPU_REGION_DISABLE ((uint8_t)0x00) /** * @} */ @@ -153,8 +136,8 @@ typedef struct /** @defgroup CORTEX_MPU_Instruction_Access CORTEX MPU Instruction Access * @{ */ -#define MPU_INSTRUCTION_ACCESS_ENABLE ((uint8_t)0x00U) -#define MPU_INSTRUCTION_ACCESS_DISABLE ((uint8_t)0x01U) +#define MPU_INSTRUCTION_ACCESS_ENABLE ((uint8_t)0x00) +#define MPU_INSTRUCTION_ACCESS_DISABLE ((uint8_t)0x01) /** * @} */ @@ -162,8 +145,8 @@ typedef struct /** @defgroup CORTEX_MPU_Access_Shareable CORTEX MPU Instruction Access Shareable * @{ */ -#define MPU_ACCESS_SHAREABLE ((uint8_t)0x01U) -#define MPU_ACCESS_NOT_SHAREABLE ((uint8_t)0x00U) +#define MPU_ACCESS_SHAREABLE ((uint8_t)0x01) +#define MPU_ACCESS_NOT_SHAREABLE ((uint8_t)0x00) /** * @} */ @@ -171,8 +154,8 @@ typedef struct /** @defgroup CORTEX_MPU_Access_Cacheable CORTEX MPU Instruction Access Cacheable * @{ */ -#define MPU_ACCESS_CACHEABLE ((uint8_t)0x01U) -#define MPU_ACCESS_NOT_CACHEABLE ((uint8_t)0x00U) +#define MPU_ACCESS_CACHEABLE ((uint8_t)0x01) +#define MPU_ACCESS_NOT_CACHEABLE ((uint8_t)0x00) /** * @} */ @@ -180,8 +163,8 @@ typedef struct /** @defgroup CORTEX_MPU_Access_Bufferable CORTEX MPU Instruction Access Bufferable * @{ */ -#define MPU_ACCESS_BUFFERABLE ((uint8_t)0x01U) -#define MPU_ACCESS_NOT_BUFFERABLE ((uint8_t)0x00U) +#define MPU_ACCESS_BUFFERABLE ((uint8_t)0x01) +#define MPU_ACCESS_NOT_BUFFERABLE ((uint8_t)0x00) /** * @} */ @@ -189,9 +172,9 @@ typedef struct /** @defgroup CORTEX_MPU_TEX_Levels MPU TEX Levels * @{ */ -#define MPU_TEX_LEVEL0 ((uint8_t)0x00U) -#define MPU_TEX_LEVEL1 ((uint8_t)0x01U) -#define MPU_TEX_LEVEL2 ((uint8_t)0x02U) +#define MPU_TEX_LEVEL0 ((uint8_t)0x00) +#define MPU_TEX_LEVEL1 ((uint8_t)0x01) +#define MPU_TEX_LEVEL2 ((uint8_t)0x02) /** * @} */ @@ -199,34 +182,34 @@ typedef struct /** @defgroup CORTEX_MPU_Region_Size CORTEX MPU Region Size * @{ */ -#define MPU_REGION_SIZE_32B ((uint8_t)0x04U) -#define MPU_REGION_SIZE_64B ((uint8_t)0x05U) -#define MPU_REGION_SIZE_128B ((uint8_t)0x06U) -#define MPU_REGION_SIZE_256B ((uint8_t)0x07U) -#define MPU_REGION_SIZE_512B ((uint8_t)0x08U) -#define MPU_REGION_SIZE_1KB ((uint8_t)0x09U) -#define MPU_REGION_SIZE_2KB ((uint8_t)0x0AU) -#define MPU_REGION_SIZE_4KB ((uint8_t)0x0BU) -#define MPU_REGION_SIZE_8KB ((uint8_t)0x0CU) -#define MPU_REGION_SIZE_16KB ((uint8_t)0x0DU) -#define MPU_REGION_SIZE_32KB ((uint8_t)0x0EU) -#define MPU_REGION_SIZE_64KB ((uint8_t)0x0FU) -#define MPU_REGION_SIZE_128KB ((uint8_t)0x10U) -#define MPU_REGION_SIZE_256KB ((uint8_t)0x11U) -#define MPU_REGION_SIZE_512KB ((uint8_t)0x12U) -#define MPU_REGION_SIZE_1MB ((uint8_t)0x13U) -#define MPU_REGION_SIZE_2MB ((uint8_t)0x14U) -#define MPU_REGION_SIZE_4MB ((uint8_t)0x15U) -#define MPU_REGION_SIZE_8MB ((uint8_t)0x16U) -#define MPU_REGION_SIZE_16MB ((uint8_t)0x17U) -#define MPU_REGION_SIZE_32MB ((uint8_t)0x18U) -#define MPU_REGION_SIZE_64MB ((uint8_t)0x19U) -#define MPU_REGION_SIZE_128MB ((uint8_t)0x1AU) -#define MPU_REGION_SIZE_256MB ((uint8_t)0x1BU) -#define MPU_REGION_SIZE_512MB ((uint8_t)0x1CU) -#define MPU_REGION_SIZE_1GB ((uint8_t)0x1DU) -#define MPU_REGION_SIZE_2GB ((uint8_t)0x1EU) -#define MPU_REGION_SIZE_4GB ((uint8_t)0x1FU) +#define MPU_REGION_SIZE_32B ((uint8_t)0x04) +#define MPU_REGION_SIZE_64B ((uint8_t)0x05) +#define MPU_REGION_SIZE_128B ((uint8_t)0x06) +#define MPU_REGION_SIZE_256B ((uint8_t)0x07) +#define MPU_REGION_SIZE_512B ((uint8_t)0x08) +#define MPU_REGION_SIZE_1KB ((uint8_t)0x09) +#define MPU_REGION_SIZE_2KB ((uint8_t)0x0A) +#define MPU_REGION_SIZE_4KB ((uint8_t)0x0B) +#define MPU_REGION_SIZE_8KB ((uint8_t)0x0C) +#define MPU_REGION_SIZE_16KB ((uint8_t)0x0D) +#define MPU_REGION_SIZE_32KB ((uint8_t)0x0E) +#define MPU_REGION_SIZE_64KB ((uint8_t)0x0F) +#define MPU_REGION_SIZE_128KB ((uint8_t)0x10) +#define MPU_REGION_SIZE_256KB ((uint8_t)0x11) +#define MPU_REGION_SIZE_512KB ((uint8_t)0x12) +#define MPU_REGION_SIZE_1MB ((uint8_t)0x13) +#define MPU_REGION_SIZE_2MB ((uint8_t)0x14) +#define MPU_REGION_SIZE_4MB ((uint8_t)0x15) +#define MPU_REGION_SIZE_8MB ((uint8_t)0x16) +#define MPU_REGION_SIZE_16MB ((uint8_t)0x17) +#define MPU_REGION_SIZE_32MB ((uint8_t)0x18) +#define MPU_REGION_SIZE_64MB ((uint8_t)0x19) +#define MPU_REGION_SIZE_128MB ((uint8_t)0x1A) +#define MPU_REGION_SIZE_256MB ((uint8_t)0x1B) +#define MPU_REGION_SIZE_512MB ((uint8_t)0x1C) +#define MPU_REGION_SIZE_1GB ((uint8_t)0x1D) +#define MPU_REGION_SIZE_2GB ((uint8_t)0x1E) +#define MPU_REGION_SIZE_4GB ((uint8_t)0x1F) /** * @} */ @@ -234,12 +217,12 @@ typedef struct /** @defgroup CORTEX_MPU_Region_Permission_Attributes CORTEX MPU Region Permission Attributes * @{ */ -#define MPU_REGION_NO_ACCESS ((uint8_t)0x00U) -#define MPU_REGION_PRIV_RW ((uint8_t)0x01U) -#define MPU_REGION_PRIV_RW_URO ((uint8_t)0x02U) -#define MPU_REGION_FULL_ACCESS ((uint8_t)0x03U) -#define MPU_REGION_PRIV_RO ((uint8_t)0x05U) -#define MPU_REGION_PRIV_RO_URO ((uint8_t)0x06U) +#define MPU_REGION_NO_ACCESS ((uint8_t)0x00) +#define MPU_REGION_PRIV_RW ((uint8_t)0x01) +#define MPU_REGION_PRIV_RW_URO ((uint8_t)0x02) +#define MPU_REGION_FULL_ACCESS ((uint8_t)0x03) +#define MPU_REGION_PRIV_RO ((uint8_t)0x05) +#define MPU_REGION_PRIV_RO_URO ((uint8_t)0x06) /** * @} */ @@ -247,14 +230,14 @@ typedef struct /** @defgroup CORTEX_MPU_Region_Number CORTEX MPU Region Number * @{ */ -#define MPU_REGION_NUMBER0 ((uint8_t)0x00U) -#define MPU_REGION_NUMBER1 ((uint8_t)0x01U) -#define MPU_REGION_NUMBER2 ((uint8_t)0x02U) -#define MPU_REGION_NUMBER3 ((uint8_t)0x03U) -#define MPU_REGION_NUMBER4 ((uint8_t)0x04U) -#define MPU_REGION_NUMBER5 ((uint8_t)0x05U) -#define MPU_REGION_NUMBER6 ((uint8_t)0x06U) -#define MPU_REGION_NUMBER7 ((uint8_t)0x07U) +#define MPU_REGION_NUMBER0 ((uint8_t)0x00) +#define MPU_REGION_NUMBER1 ((uint8_t)0x01) +#define MPU_REGION_NUMBER2 ((uint8_t)0x02) +#define MPU_REGION_NUMBER3 ((uint8_t)0x03) +#define MPU_REGION_NUMBER4 ((uint8_t)0x04) +#define MPU_REGION_NUMBER5 ((uint8_t)0x05) +#define MPU_REGION_NUMBER6 ((uint8_t)0x06) +#define MPU_REGION_NUMBER7 ((uint8_t)0x07) /** * @} */ @@ -273,8 +256,8 @@ typedef struct */ /** @addtogroup CORTEX_Exported_Functions_Group1 - * @{ - */ + * @{ + */ /* Initialization and de-initialization functions *****************************/ void HAL_NVIC_SetPriorityGrouping(uint32_t PriorityGroup); void HAL_NVIC_SetPriority(IRQn_Type IRQn, uint32_t PreemptPriority, uint32_t SubPriority); @@ -287,12 +270,9 @@ uint32_t HAL_SYSTICK_Config(uint32_t TicksNumb); */ /** @addtogroup CORTEX_Exported_Functions_Group2 - * @{ - */ + * @{ + */ /* Peripheral Control functions ***********************************************/ -#if (__MPU_PRESENT == 1) -void HAL_MPU_ConfigRegion(MPU_Region_InitTypeDef* MPU_Init); -#endif /* __MPU_PRESENT */ uint32_t HAL_NVIC_GetPriorityGrouping(void); void HAL_NVIC_GetPriority(IRQn_Type IRQn, uint32_t PriorityGroup, uint32_t* pPreemptPriority, uint32_t* pSubPriority); uint32_t HAL_NVIC_GetPendingIRQ(IRQn_Type IRQn); @@ -302,6 +282,12 @@ uint32_t HAL_NVIC_GetActive(IRQn_Type IRQn); void HAL_SYSTICK_CLKSourceConfig(uint32_t CLKSource); void HAL_SYSTICK_IRQHandler(void); void HAL_SYSTICK_Callback(void); + +#if (__MPU_PRESENT == 1U) +void HAL_MPU_Enable(uint32_t MPU_Control); +void HAL_MPU_Disable(void); +void HAL_MPU_ConfigRegion(MPU_Region_InitTypeDef* MPU_Init); +#endif /* __MPU_PRESENT */ /** * @} */ @@ -397,7 +383,7 @@ void HAL_SYSTICK_Callback(void); ((SIZE) == MPU_REGION_SIZE_2GB) || \ ((SIZE) == MPU_REGION_SIZE_4GB)) -#define IS_MPU_SUB_REGION_DISABLE(SUBREGION) ((SUBREGION) < (uint16_t)0x00FFU) +#define IS_MPU_SUB_REGION_DISABLE(SUBREGION) ((SUBREGION) < (uint16_t)0x00FF) #endif /* __MPU_PRESENT */ /** @@ -405,47 +391,6 @@ void HAL_SYSTICK_Callback(void); */ /* Private functions ---------------------------------------------------------*/ -/** @defgroup CORTEX_Private_Functions CORTEX Private Functions - * @brief CORTEX private functions - * @{ - */ - -#if (__MPU_PRESENT == 1) -/** - * @brief Disables the MPU - * @retval None - */ -__STATIC_INLINE void HAL_MPU_Disable(void) -{ - /* Disable fault exceptions */ - SCB->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk; - /* Disable the MPU */ - MPU->CTRL &= ~MPU_CTRL_ENABLE_Msk; -} - -/** - * @brief Enables the MPU - * @param MPU_Control: Specifies the control mode of the MPU during hard fault, - * NMI, FAULTMASK and privileged access to the default memory - * This parameter can be one of the following values: - * @arg MPU_HFNMI_PRIVDEF_NONE - * @arg MPU_HARDFAULT_NMI - * @arg MPU_PRIVILEGED_DEFAULT - * @arg MPU_HFNMI_PRIVDEF - * @retval None - */ -__STATIC_INLINE void HAL_MPU_Enable(uint32_t MPU_Control) -{ - /* Enable the MPU */ - MPU->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk; - /* Enable fault exceptions */ - SCB->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk; -} -#endif /* __MPU_PRESENT */ - -/** - * @} - */ /** * @} @@ -459,7 +404,7 @@ __STATIC_INLINE void HAL_MPU_Enable(uint32_t MPU_Control) } #endif -#endif /* __STM32F4xx_HAL_CORTEX_H */ +#endif /* __STM32F1xx_HAL_CORTEX_H */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_def.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_def.h similarity index 70% rename from EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_def.h rename to EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_def.h index 79a8ffd2..675e3c1d 100644 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_def.h +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_def.h @@ -1,53 +1,37 @@ /** ****************************************************************************** - * @file stm32f4xx_hal_def.h + * @file stm32f1xx_hal_def.h * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 * @brief This file contains HAL common defines, enumeration, macros and * structures definitions. ****************************************************************************** * @attention * - *

© COPYRIGHT(c) 2016 STMicroelectronics

+ *

© Copyright (c) 2017 STMicroelectronics. + * All rights reserved.

* - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause * ****************************************************************************** */ /* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_DEF -#define __STM32F4xx_HAL_DEF +#ifndef __STM32F1xx_HAL_DEF +#define __STM32F1xx_HAL_DEF #ifdef __cplusplus extern "C" { #endif /* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx.h" +#include "stm32f1xx.h" +#if defined(USE_HAL_LEGACY) #include "Legacy/stm32_hal_legacy.h" -#include +#endif +#include /* Exported types ------------------------------------------------------------*/ @@ -74,19 +58,19 @@ typedef enum /* Exported macro ------------------------------------------------------------*/ #define HAL_MAX_DELAY 0xFFFFFFFFU -#define HAL_IS_BIT_SET(REG, BIT) (((REG) & (BIT)) != RESET) -#define HAL_IS_BIT_CLR(REG, BIT) (((REG) & (BIT)) == RESET) +#define HAL_IS_BIT_SET(REG, BIT) (((REG) & (BIT)) != 0U) +#define HAL_IS_BIT_CLR(REG, BIT) (((REG) & (BIT)) == 0U) #define __HAL_LINKDMA(__HANDLE__, __PPP_DMA_FIELD__, __DMA_HANDLE__) \ do{ \ (__HANDLE__)->__PPP_DMA_FIELD__ = &(__DMA_HANDLE__); \ (__DMA_HANDLE__).Parent = (__HANDLE__); \ - } while(0) + } while(0U) -#define UNUSED(x) ((void)(x)) +#define UNUSED(X) (void)X /* To avoid gcc/g++ warnings */ /** @brief Reset the Handle's State field. - * @param __HANDLE__: specifies the Peripheral Handle. + * @param __HANDLE__ specifies the Peripheral Handle. * @note This macro can be used for the following purpose: * - When the Handle is declared as local variable; before passing it as parameter * to HAL_PPP_Init() for the first time, it is mandatory to use this macro @@ -102,7 +86,7 @@ typedef enum */ #define __HAL_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = 0U) -#if (USE_RTOS == 1) +#if (USE_RTOS == 1U) /* Reserved for future use */ #error "USE_RTOS should be 0 in the current HAL release" #else @@ -116,15 +100,15 @@ typedef enum { \ (__HANDLE__)->Lock = HAL_LOCKED; \ } \ - }while (0) + }while (0U) #define __HAL_UNLOCK(__HANDLE__) \ do{ \ (__HANDLE__)->Lock = HAL_UNLOCKED; \ - }while (0) + }while (0U) #endif /* USE_RTOS */ -#if defined ( __GNUC__ ) +#if defined ( __GNUC__ ) && !defined (__CC_ARM) /* GNU Compiler */ #ifndef __weak #define __weak __attribute__((weak)) #endif /* __weak */ @@ -135,7 +119,7 @@ typedef enum /* Macro to get variable aligned on 4-bytes, for __ICCARM__ the directive "#pragma data_alignment=4" must be used instead */ -#if defined (__GNUC__) /* GNU Compiler */ +#if defined ( __GNUC__ ) && !defined (__CC_ARM) /* GNU Compiler */ #ifndef __ALIGN_END #define __ALIGN_END __attribute__ ((aligned (4))) #endif /* __ALIGN_END */ @@ -169,14 +153,14 @@ typedef enum Available memory areas are declared in the 'Target' tab of the 'Options for Target' dialog. */ -#define __RAM_FUNC HAL_StatusTypeDef +#define __RAM_FUNC #elif defined ( __ICCARM__ ) /* ICCARM Compiler --------------- RAM functions are defined using a specific toolchain keyword "__ramfunc". */ -#define __RAM_FUNC __ramfunc HAL_StatusTypeDef +#define __RAM_FUNC __ramfunc #elif defined ( __GNUC__ ) /* GNU Compiler @@ -184,7 +168,7 @@ typedef enum RAM functions are defined using a specific toolchain attribute "__attribute__((section(".RamFunc")))". */ -#define __RAM_FUNC HAL_StatusTypeDef __attribute__((section(".RamFunc"))) +#define __RAM_FUNC __attribute__((section(".RamFunc"))) #endif @@ -209,6 +193,6 @@ typedef enum } #endif -#endif /* ___STM32F4xx_HAL_DEF */ +#endif /* ___STM32F1xx_HAL_DEF */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_dma.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_dma.h new file mode 100644 index 00000000..7a2a2601 --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_dma.h @@ -0,0 +1,457 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_dma.h + * @author MCD Application Team + * @brief Header file of DMA HAL module. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F1xx_HAL_DMA_H +#define __STM32F1xx_HAL_DMA_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal_def.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @addtogroup DMA + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ + +/** @defgroup DMA_Exported_Types DMA Exported Types + * @{ + */ + +/** + * @brief DMA Configuration Structure definition + */ +typedef struct +{ + uint32_t Direction; /*!< Specifies if the data will be transferred from memory to peripheral, + from memory to memory or from peripheral to memory. + This parameter can be a value of @ref DMA_Data_transfer_direction */ + + uint32_t PeriphInc; /*!< Specifies whether the Peripheral address register should be incremented or not. + This parameter can be a value of @ref DMA_Peripheral_incremented_mode */ + + uint32_t MemInc; /*!< Specifies whether the memory address register should be incremented or not. + This parameter can be a value of @ref DMA_Memory_incremented_mode */ + + uint32_t PeriphDataAlignment; /*!< Specifies the Peripheral data width. + This parameter can be a value of @ref DMA_Peripheral_data_size */ + + uint32_t MemDataAlignment; /*!< Specifies the Memory data width. + This parameter can be a value of @ref DMA_Memory_data_size */ + + uint32_t Mode; /*!< Specifies the operation mode of the DMAy Channelx. + This parameter can be a value of @ref DMA_mode + @note The circular buffer mode cannot be used if the memory-to-memory + data transfer is configured on the selected Channel */ + + uint32_t Priority; /*!< Specifies the software priority for the DMAy Channelx. + This parameter can be a value of @ref DMA_Priority_level */ +} DMA_InitTypeDef; + +/** + * @brief HAL DMA State structures definition + */ +typedef enum +{ + HAL_DMA_STATE_RESET = 0x00U, /*!< DMA not yet initialized or disabled */ + HAL_DMA_STATE_READY = 0x01U, /*!< DMA initialized and ready for use */ + HAL_DMA_STATE_BUSY = 0x02U, /*!< DMA process is ongoing */ + HAL_DMA_STATE_TIMEOUT = 0x03U /*!< DMA timeout state */ +} HAL_DMA_StateTypeDef; + +/** + * @brief HAL DMA Error Code structure definition + */ +typedef enum +{ + HAL_DMA_FULL_TRANSFER = 0x00U, /*!< Full transfer */ + HAL_DMA_HALF_TRANSFER = 0x01U /*!< Half Transfer */ +} HAL_DMA_LevelCompleteTypeDef; + +/** + * @brief HAL DMA Callback ID structure definition + */ +typedef enum +{ + HAL_DMA_XFER_CPLT_CB_ID = 0x00U, /*!< Full transfer */ + HAL_DMA_XFER_HALFCPLT_CB_ID = 0x01U, /*!< Half transfer */ + HAL_DMA_XFER_ERROR_CB_ID = 0x02U, /*!< Error */ + HAL_DMA_XFER_ABORT_CB_ID = 0x03U, /*!< Abort */ + HAL_DMA_XFER_ALL_CB_ID = 0x04U /*!< All */ + +} HAL_DMA_CallbackIDTypeDef; + +/** + * @brief DMA handle Structure definition + */ +typedef struct __DMA_HandleTypeDef +{ + DMA_Channel_TypeDef* Instance; /*!< Register base address */ + + DMA_InitTypeDef Init; /*!< DMA communication parameters */ + + HAL_LockTypeDef Lock; /*!< DMA locking object */ + + HAL_DMA_StateTypeDef State; /*!< DMA transfer state */ + + void* Parent; /*!< Parent object state */ + + void (* XferCpltCallback)( struct __DMA_HandleTypeDef* hdma); /*!< DMA transfer complete callback */ + + void (* XferHalfCpltCallback)( struct __DMA_HandleTypeDef* hdma); /*!< DMA Half transfer complete callback */ + + void (* XferErrorCallback)( struct __DMA_HandleTypeDef* hdma); /*!< DMA transfer error callback */ + + void (* XferAbortCallback)( struct __DMA_HandleTypeDef* hdma); /*!< DMA transfer abort callback */ + + __IO uint32_t ErrorCode; /*!< DMA Error code */ + + DMA_TypeDef* DmaBaseAddress; /*!< DMA Channel Base Address */ + + uint32_t ChannelIndex; /*!< DMA Channel Index */ + +} DMA_HandleTypeDef; +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ + +/** @defgroup DMA_Exported_Constants DMA Exported Constants + * @{ + */ + +/** @defgroup DMA_Error_Code DMA Error Code + * @{ + */ +#define HAL_DMA_ERROR_NONE 0x00000000U /*!< No error */ +#define HAL_DMA_ERROR_TE 0x00000001U /*!< Transfer error */ +#define HAL_DMA_ERROR_NO_XFER 0x00000004U /*!< no ongoing transfer */ +#define HAL_DMA_ERROR_TIMEOUT 0x00000020U /*!< Timeout error */ +#define HAL_DMA_ERROR_NOT_SUPPORTED 0x00000100U /*!< Not supported mode */ +/** + * @} + */ + +/** @defgroup DMA_Data_transfer_direction DMA Data transfer direction + * @{ + */ +#define DMA_PERIPH_TO_MEMORY 0x00000000U /*!< Peripheral to memory direction */ +#define DMA_MEMORY_TO_PERIPH ((uint32_t)DMA_CCR_DIR) /*!< Memory to peripheral direction */ +#define DMA_MEMORY_TO_MEMORY ((uint32_t)DMA_CCR_MEM2MEM) /*!< Memory to memory direction */ + +/** + * @} + */ + +/** @defgroup DMA_Peripheral_incremented_mode DMA Peripheral incremented mode + * @{ + */ +#define DMA_PINC_ENABLE ((uint32_t)DMA_CCR_PINC) /*!< Peripheral increment mode Enable */ +#define DMA_PINC_DISABLE 0x00000000U /*!< Peripheral increment mode Disable */ +/** + * @} + */ + +/** @defgroup DMA_Memory_incremented_mode DMA Memory incremented mode + * @{ + */ +#define DMA_MINC_ENABLE ((uint32_t)DMA_CCR_MINC) /*!< Memory increment mode Enable */ +#define DMA_MINC_DISABLE 0x00000000U /*!< Memory increment mode Disable */ +/** + * @} + */ + +/** @defgroup DMA_Peripheral_data_size DMA Peripheral data size + * @{ + */ +#define DMA_PDATAALIGN_BYTE 0x00000000U /*!< Peripheral data alignment: Byte */ +#define DMA_PDATAALIGN_HALFWORD ((uint32_t)DMA_CCR_PSIZE_0) /*!< Peripheral data alignment: HalfWord */ +#define DMA_PDATAALIGN_WORD ((uint32_t)DMA_CCR_PSIZE_1) /*!< Peripheral data alignment: Word */ +/** + * @} + */ + +/** @defgroup DMA_Memory_data_size DMA Memory data size + * @{ + */ +#define DMA_MDATAALIGN_BYTE 0x00000000U /*!< Memory data alignment: Byte */ +#define DMA_MDATAALIGN_HALFWORD ((uint32_t)DMA_CCR_MSIZE_0) /*!< Memory data alignment: HalfWord */ +#define DMA_MDATAALIGN_WORD ((uint32_t)DMA_CCR_MSIZE_1) /*!< Memory data alignment: Word */ +/** + * @} + */ + +/** @defgroup DMA_mode DMA mode + * @{ + */ +#define DMA_NORMAL 0x00000000U /*!< Normal mode */ +#define DMA_CIRCULAR ((uint32_t)DMA_CCR_CIRC) /*!< Circular mode */ +/** + * @} + */ + +/** @defgroup DMA_Priority_level DMA Priority level + * @{ + */ +#define DMA_PRIORITY_LOW 0x00000000U /*!< Priority level : Low */ +#define DMA_PRIORITY_MEDIUM ((uint32_t)DMA_CCR_PL_0) /*!< Priority level : Medium */ +#define DMA_PRIORITY_HIGH ((uint32_t)DMA_CCR_PL_1) /*!< Priority level : High */ +#define DMA_PRIORITY_VERY_HIGH ((uint32_t)DMA_CCR_PL) /*!< Priority level : Very_High */ +/** + * @} + */ + + +/** @defgroup DMA_interrupt_enable_definitions DMA interrupt enable definitions + * @{ + */ +#define DMA_IT_TC ((uint32_t)DMA_CCR_TCIE) +#define DMA_IT_HT ((uint32_t)DMA_CCR_HTIE) +#define DMA_IT_TE ((uint32_t)DMA_CCR_TEIE) +/** + * @} + */ + +/** @defgroup DMA_flag_definitions DMA flag definitions + * @{ + */ +#define DMA_FLAG_GL1 0x00000001U +#define DMA_FLAG_TC1 0x00000002U +#define DMA_FLAG_HT1 0x00000004U +#define DMA_FLAG_TE1 0x00000008U +#define DMA_FLAG_GL2 0x00000010U +#define DMA_FLAG_TC2 0x00000020U +#define DMA_FLAG_HT2 0x00000040U +#define DMA_FLAG_TE2 0x00000080U +#define DMA_FLAG_GL3 0x00000100U +#define DMA_FLAG_TC3 0x00000200U +#define DMA_FLAG_HT3 0x00000400U +#define DMA_FLAG_TE3 0x00000800U +#define DMA_FLAG_GL4 0x00001000U +#define DMA_FLAG_TC4 0x00002000U +#define DMA_FLAG_HT4 0x00004000U +#define DMA_FLAG_TE4 0x00008000U +#define DMA_FLAG_GL5 0x00010000U +#define DMA_FLAG_TC5 0x00020000U +#define DMA_FLAG_HT5 0x00040000U +#define DMA_FLAG_TE5 0x00080000U +#define DMA_FLAG_GL6 0x00100000U +#define DMA_FLAG_TC6 0x00200000U +#define DMA_FLAG_HT6 0x00400000U +#define DMA_FLAG_TE6 0x00800000U +#define DMA_FLAG_GL7 0x01000000U +#define DMA_FLAG_TC7 0x02000000U +#define DMA_FLAG_HT7 0x04000000U +#define DMA_FLAG_TE7 0x08000000U +/** + * @} + */ + +/** + * @} + */ + + +/* Exported macros -----------------------------------------------------------*/ +/** @defgroup DMA_Exported_Macros DMA Exported Macros + * @{ + */ + +/** @brief Reset DMA handle state. + * @param __HANDLE__: DMA handle + * @retval None + */ +#define __HAL_DMA_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_DMA_STATE_RESET) + +/** + * @brief Enable the specified DMA Channel. + * @param __HANDLE__: DMA handle + * @retval None + */ +#define __HAL_DMA_ENABLE(__HANDLE__) (SET_BIT((__HANDLE__)->Instance->CCR, DMA_CCR_EN)) + +/** + * @brief Disable the specified DMA Channel. + * @param __HANDLE__: DMA handle + * @retval None + */ +#define __HAL_DMA_DISABLE(__HANDLE__) (CLEAR_BIT((__HANDLE__)->Instance->CCR, DMA_CCR_EN)) + + +/* Interrupt & Flag management */ + +/** + * @brief Enables the specified DMA Channel interrupts. + * @param __HANDLE__: DMA handle + * @param __INTERRUPT__: specifies the DMA interrupt sources to be enabled or disabled. + * This parameter can be any combination of the following values: + * @arg DMA_IT_TC: Transfer complete interrupt mask + * @arg DMA_IT_HT: Half transfer complete interrupt mask + * @arg DMA_IT_TE: Transfer error interrupt mask + * @retval None + */ +#define __HAL_DMA_ENABLE_IT(__HANDLE__, __INTERRUPT__) (SET_BIT((__HANDLE__)->Instance->CCR, (__INTERRUPT__))) + +/** + * @brief Disable the specified DMA Channel interrupts. + * @param __HANDLE__: DMA handle + * @param __INTERRUPT__: specifies the DMA interrupt sources to be enabled or disabled. + * This parameter can be any combination of the following values: + * @arg DMA_IT_TC: Transfer complete interrupt mask + * @arg DMA_IT_HT: Half transfer complete interrupt mask + * @arg DMA_IT_TE: Transfer error interrupt mask + * @retval None + */ +#define __HAL_DMA_DISABLE_IT(__HANDLE__, __INTERRUPT__) (CLEAR_BIT((__HANDLE__)->Instance->CCR , (__INTERRUPT__))) + +/** + * @brief Check whether the specified DMA Channel interrupt is enabled or not. + * @param __HANDLE__: DMA handle + * @param __INTERRUPT__: specifies the DMA interrupt source to check. + * This parameter can be one of the following values: + * @arg DMA_IT_TC: Transfer complete interrupt mask + * @arg DMA_IT_HT: Half transfer complete interrupt mask + * @arg DMA_IT_TE: Transfer error interrupt mask + * @retval The state of DMA_IT (SET or RESET). + */ +#define __HAL_DMA_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->CCR & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET) + +/** + * @brief Return the number of remaining data units in the current DMA Channel transfer. + * @param __HANDLE__: DMA handle + * @retval The number of remaining data units in the current DMA Channel transfer. + */ +#define __HAL_DMA_GET_COUNTER(__HANDLE__) ((__HANDLE__)->Instance->CNDTR) + +/** + * @} + */ + +/* Include DMA HAL Extension module */ +#include "stm32f1xx_hal_dma_ex.h" + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup DMA_Exported_Functions + * @{ + */ + +/** @addtogroup DMA_Exported_Functions_Group1 + * @{ + */ +/* Initialization and de-initialization functions *****************************/ +HAL_StatusTypeDef HAL_DMA_Init(DMA_HandleTypeDef* hdma); +HAL_StatusTypeDef HAL_DMA_DeInit (DMA_HandleTypeDef* hdma); +/** + * @} + */ + +/** @addtogroup DMA_Exported_Functions_Group2 + * @{ + */ +/* IO operation functions *****************************************************/ +HAL_StatusTypeDef HAL_DMA_Start (DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength); +HAL_StatusTypeDef HAL_DMA_Start_IT(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength); +HAL_StatusTypeDef HAL_DMA_Abort(DMA_HandleTypeDef* hdma); +HAL_StatusTypeDef HAL_DMA_Abort_IT(DMA_HandleTypeDef* hdma); +HAL_StatusTypeDef HAL_DMA_PollForTransfer(DMA_HandleTypeDef* hdma, uint32_t CompleteLevel, uint32_t Timeout); +void HAL_DMA_IRQHandler(DMA_HandleTypeDef* hdma); +HAL_StatusTypeDef HAL_DMA_RegisterCallback(DMA_HandleTypeDef* hdma, HAL_DMA_CallbackIDTypeDef CallbackID, void (* pCallback)( DMA_HandleTypeDef* _hdma)); +HAL_StatusTypeDef HAL_DMA_UnRegisterCallback(DMA_HandleTypeDef* hdma, HAL_DMA_CallbackIDTypeDef CallbackID); + +/** + * @} + */ + +/** @addtogroup DMA_Exported_Functions_Group3 + * @{ + */ +/* Peripheral State and Error functions ***************************************/ +HAL_DMA_StateTypeDef HAL_DMA_GetState(DMA_HandleTypeDef* hdma); +uint32_t HAL_DMA_GetError(DMA_HandleTypeDef* hdma); +/** + * @} + */ + +/** + * @} + */ + +/* Private macros ------------------------------------------------------------*/ +/** @defgroup DMA_Private_Macros DMA Private Macros + * @{ + */ + +#define IS_DMA_DIRECTION(DIRECTION) (((DIRECTION) == DMA_PERIPH_TO_MEMORY ) || \ + ((DIRECTION) == DMA_MEMORY_TO_PERIPH) || \ + ((DIRECTION) == DMA_MEMORY_TO_MEMORY)) + +#define IS_DMA_BUFFER_SIZE(SIZE) (((SIZE) >= 0x1U) && ((SIZE) < 0x10000U)) + +#define IS_DMA_PERIPHERAL_INC_STATE(STATE) (((STATE) == DMA_PINC_ENABLE) || \ + ((STATE) == DMA_PINC_DISABLE)) + +#define IS_DMA_MEMORY_INC_STATE(STATE) (((STATE) == DMA_MINC_ENABLE) || \ + ((STATE) == DMA_MINC_DISABLE)) + +#define IS_DMA_PERIPHERAL_DATA_SIZE(SIZE) (((SIZE) == DMA_PDATAALIGN_BYTE) || \ + ((SIZE) == DMA_PDATAALIGN_HALFWORD) || \ + ((SIZE) == DMA_PDATAALIGN_WORD)) + +#define IS_DMA_MEMORY_DATA_SIZE(SIZE) (((SIZE) == DMA_MDATAALIGN_BYTE) || \ + ((SIZE) == DMA_MDATAALIGN_HALFWORD) || \ + ((SIZE) == DMA_MDATAALIGN_WORD )) + +#define IS_DMA_MODE(MODE) (((MODE) == DMA_NORMAL ) || \ + ((MODE) == DMA_CIRCULAR)) + +#define IS_DMA_PRIORITY(PRIORITY) (((PRIORITY) == DMA_PRIORITY_LOW ) || \ + ((PRIORITY) == DMA_PRIORITY_MEDIUM) || \ + ((PRIORITY) == DMA_PRIORITY_HIGH) || \ + ((PRIORITY) == DMA_PRIORITY_VERY_HIGH)) + +/** + * @} + */ + +/* Private functions ---------------------------------------------------------*/ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F1xx_HAL_DMA_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_dma_ex.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_dma_ex.h new file mode 100644 index 00000000..d1a0acfe --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_dma_ex.h @@ -0,0 +1,277 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_dma_ex.h + * @author MCD Application Team + * @brief Header file of DMA HAL extension module. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F1xx_HAL_DMA_EX_H +#define __STM32F1xx_HAL_DMA_EX_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal_def.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @defgroup DMAEx DMAEx + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup DMAEx_Exported_Macros DMA Extended Exported Macros + * @{ + */ +/* Interrupt & Flag management */ +#if defined (STM32F100xE) || defined (STM32F101xE) || defined (STM32F101xG) || defined (STM32F103xE) || \ + defined (STM32F103xG) || defined (STM32F105xC) || defined (STM32F107xC) +/** @defgroup DMAEx_High_density_XL_density_Product_devices DMAEx High density and XL density product devices + * @{ + */ + +/** + * @brief Returns the current DMA Channel transfer complete flag. + * @param __HANDLE__: DMA handle + * @retval The specified transfer complete flag index. + */ +#define __HAL_DMA_GET_TC_FLAG_INDEX(__HANDLE__) \ +(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TC1 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TC2 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TC3 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TC4 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_TC5 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_TC6 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel7))? DMA_FLAG_TC7 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel1))? DMA_FLAG_TC1 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel2))? DMA_FLAG_TC2 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel3))? DMA_FLAG_TC3 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel4))? DMA_FLAG_TC4 :\ + DMA_FLAG_TC5) + +/** + * @brief Returns the current DMA Channel half transfer complete flag. + * @param __HANDLE__: DMA handle + * @retval The specified half transfer complete flag index. + */ +#define __HAL_DMA_GET_HT_FLAG_INDEX(__HANDLE__)\ +(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_HT1 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_HT2 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_HT3 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_HT4 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_HT5 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_HT6 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel7))? DMA_FLAG_HT7 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel1))? DMA_FLAG_HT1 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel2))? DMA_FLAG_HT2 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel3))? DMA_FLAG_HT3 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel4))? DMA_FLAG_HT4 :\ + DMA_FLAG_HT5) + +/** + * @brief Returns the current DMA Channel transfer error flag. + * @param __HANDLE__: DMA handle + * @retval The specified transfer error flag index. + */ +#define __HAL_DMA_GET_TE_FLAG_INDEX(__HANDLE__)\ +(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TE1 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TE2 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TE3 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TE4 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_TE5 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_TE6 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel7))? DMA_FLAG_TE7 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel1))? DMA_FLAG_TE1 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel2))? DMA_FLAG_TE2 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel3))? DMA_FLAG_TE3 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel4))? DMA_FLAG_TE4 :\ + DMA_FLAG_TE5) + +/** + * @brief Return the current DMA Channel Global interrupt flag. + * @param __HANDLE__: DMA handle + * @retval The specified transfer error flag index. + */ +#define __HAL_DMA_GET_GI_FLAG_INDEX(__HANDLE__)\ +(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_GL1 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_GL2 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_GL3 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_GL4 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_GL5 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_GL6 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel7))? DMA_FLAG_GL7 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel1))? DMA_FLAG_GL1 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel2))? DMA_FLAG_GL2 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel3))? DMA_FLAG_GL3 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel4))? DMA_FLAG_GL4 :\ + DMA_FLAG_GL5) + +/** + * @brief Get the DMA Channel pending flags. + * @param __HANDLE__: DMA handle + * @param __FLAG__: Get the specified flag. + * This parameter can be any combination of the following values: + * @arg DMA_FLAG_TCx: Transfer complete flag + * @arg DMA_FLAG_HTx: Half transfer complete flag + * @arg DMA_FLAG_TEx: Transfer error flag + * Where x can be 1_7 or 1_5 (depending on DMA1 or DMA2) to select the DMA Channel flag. + * @retval The state of FLAG (SET or RESET). + */ +#define __HAL_DMA_GET_FLAG(__HANDLE__, __FLAG__)\ +(((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA1_Channel7)? (DMA2->ISR & (__FLAG__)) :\ + (DMA1->ISR & (__FLAG__))) + +/** + * @brief Clears the DMA Channel pending flags. + * @param __HANDLE__: DMA handle + * @param __FLAG__: specifies the flag to clear. + * This parameter can be any combination of the following values: + * @arg DMA_FLAG_TCx: Transfer complete flag + * @arg DMA_FLAG_HTx: Half transfer complete flag + * @arg DMA_FLAG_TEx: Transfer error flag + * Where x can be 1_7 or 1_5 (depending on DMA1 or DMA2) to select the DMA Channel flag. + * @retval None + */ +#define __HAL_DMA_CLEAR_FLAG(__HANDLE__, __FLAG__) \ +(((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA1_Channel7)? (DMA2->IFCR = (__FLAG__)) :\ + (DMA1->IFCR = (__FLAG__))) + +/** + * @} + */ + +#else +/** @defgroup DMA_Low_density_Medium_density_Product_devices DMA Low density and Medium density product devices + * @{ + */ + +/** + * @brief Returns the current DMA Channel transfer complete flag. + * @param __HANDLE__: DMA handle + * @retval The specified transfer complete flag index. + */ +#define __HAL_DMA_GET_TC_FLAG_INDEX(__HANDLE__) \ +(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TC1 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TC2 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TC3 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TC4 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_TC5 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_TC6 :\ + DMA_FLAG_TC7) + +/** + * @brief Return the current DMA Channel half transfer complete flag. + * @param __HANDLE__: DMA handle + * @retval The specified half transfer complete flag index. + */ +#define __HAL_DMA_GET_HT_FLAG_INDEX(__HANDLE__)\ +(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_HT1 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_HT2 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_HT3 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_HT4 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_HT5 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_HT6 :\ + DMA_FLAG_HT7) + +/** + * @brief Return the current DMA Channel transfer error flag. + * @param __HANDLE__: DMA handle + * @retval The specified transfer error flag index. + */ +#define __HAL_DMA_GET_TE_FLAG_INDEX(__HANDLE__)\ +(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TE1 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TE2 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TE3 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TE4 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_TE5 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_TE6 :\ + DMA_FLAG_TE7) + +/** + * @brief Return the current DMA Channel Global interrupt flag. + * @param __HANDLE__: DMA handle + * @retval The specified transfer error flag index. + */ +#define __HAL_DMA_GET_GI_FLAG_INDEX(__HANDLE__)\ +(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_GL1 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_GL2 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_GL3 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_GL4 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_GL5 :\ + ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_GL6 :\ + DMA_FLAG_GL7) + +/** + * @brief Get the DMA Channel pending flags. + * @param __HANDLE__: DMA handle + * @param __FLAG__: Get the specified flag. + * This parameter can be any combination of the following values: + * @arg DMA_FLAG_TCx: Transfer complete flag + * @arg DMA_FLAG_HTx: Half transfer complete flag + * @arg DMA_FLAG_TEx: Transfer error flag + * @arg DMA_FLAG_GLx: Global interrupt flag + * Where x can be 1_7 to select the DMA Channel flag. + * @retval The state of FLAG (SET or RESET). + */ + +#define __HAL_DMA_GET_FLAG(__HANDLE__, __FLAG__) (DMA1->ISR & (__FLAG__)) + +/** + * @brief Clear the DMA Channel pending flags. + * @param __HANDLE__: DMA handle + * @param __FLAG__: specifies the flag to clear. + * This parameter can be any combination of the following values: + * @arg DMA_FLAG_TCx: Transfer complete flag + * @arg DMA_FLAG_HTx: Half transfer complete flag + * @arg DMA_FLAG_TEx: Transfer error flag + * @arg DMA_FLAG_GLx: Global interrupt flag + * Where x can be 1_7 to select the DMA Channel flag. + * @retval None + */ +#define __HAL_DMA_CLEAR_FLAG(__HANDLE__, __FLAG__) (DMA1->IFCR = (__FLAG__)) + +/** + * @} + */ + +#endif + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif /* STM32F100xE || STM32F101xE || STM32F101xG || STM32F103xE || */ +/* STM32F103xG || STM32F105xC || STM32F107xC */ + +#endif /* __STM32F1xx_HAL_DMA_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_exti.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_exti.h new file mode 100644 index 00000000..703c2664 --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_exti.h @@ -0,0 +1,320 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_exti.h + * @author MCD Application Team + * @brief Header file of EXTI HAL module. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2019 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef STM32F1xx_HAL_EXTI_H +#define STM32F1xx_HAL_EXTI_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal_def.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @defgroup EXTI EXTI + * @brief EXTI HAL module driver + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ + +/** @defgroup EXTI_Exported_Types EXTI Exported Types + * @{ + */ + +/** + * @brief HAL EXTI common Callback ID enumeration definition + */ +typedef enum +{ + HAL_EXTI_COMMON_CB_ID = 0x00U +} EXTI_CallbackIDTypeDef; + +/** + * @brief EXTI Handle structure definition + */ +typedef struct +{ + uint32_t Line; /*!< Exti line number */ + void (* PendingCallback)(void); /*!< Exti pending callback */ +} EXTI_HandleTypeDef; + +/** + * @brief EXTI Configuration structure definition + */ +typedef struct +{ + uint32_t Line; /*!< The Exti line to be configured. This parameter + can be a value of @ref EXTI_Line */ + uint32_t Mode; /*!< The Exit Mode to be configured for a core. + This parameter can be a combination of @ref EXTI_Mode */ + uint32_t Trigger; /*!< The Exti Trigger to be configured. This parameter + can be a value of @ref EXTI_Trigger */ + uint32_t GPIOSel; /*!< The Exti GPIO multiplexer selection to be configured. + This parameter is only possible for line 0 to 15. It + can be a value of @ref EXTI_GPIOSel */ +} EXTI_ConfigTypeDef; + +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup EXTI_Exported_Constants EXTI Exported Constants + * @{ + */ + +/** @defgroup EXTI_Line EXTI Line + * @{ + */ +#define EXTI_LINE_0 (EXTI_GPIO | 0x00u) /*!< External interrupt line 0 */ +#define EXTI_LINE_1 (EXTI_GPIO | 0x01u) /*!< External interrupt line 1 */ +#define EXTI_LINE_2 (EXTI_GPIO | 0x02u) /*!< External interrupt line 2 */ +#define EXTI_LINE_3 (EXTI_GPIO | 0x03u) /*!< External interrupt line 3 */ +#define EXTI_LINE_4 (EXTI_GPIO | 0x04u) /*!< External interrupt line 4 */ +#define EXTI_LINE_5 (EXTI_GPIO | 0x05u) /*!< External interrupt line 5 */ +#define EXTI_LINE_6 (EXTI_GPIO | 0x06u) /*!< External interrupt line 6 */ +#define EXTI_LINE_7 (EXTI_GPIO | 0x07u) /*!< External interrupt line 7 */ +#define EXTI_LINE_8 (EXTI_GPIO | 0x08u) /*!< External interrupt line 8 */ +#define EXTI_LINE_9 (EXTI_GPIO | 0x09u) /*!< External interrupt line 9 */ +#define EXTI_LINE_10 (EXTI_GPIO | 0x0Au) /*!< External interrupt line 10 */ +#define EXTI_LINE_11 (EXTI_GPIO | 0x0Bu) /*!< External interrupt line 11 */ +#define EXTI_LINE_12 (EXTI_GPIO | 0x0Cu) /*!< External interrupt line 12 */ +#define EXTI_LINE_13 (EXTI_GPIO | 0x0Du) /*!< External interrupt line 13 */ +#define EXTI_LINE_14 (EXTI_GPIO | 0x0Eu) /*!< External interrupt line 14 */ +#define EXTI_LINE_15 (EXTI_GPIO | 0x0Fu) /*!< External interrupt line 15 */ +#define EXTI_LINE_16 (EXTI_CONFIG | 0x10u) /*!< External interrupt line 16 Connected to the PVD Output */ +#define EXTI_LINE_17 (EXTI_CONFIG | 0x11u) /*!< External interrupt line 17 Connected to the RTC Alarm event */ +#if defined(EXTI_IMR_IM18) +#define EXTI_LINE_18 (EXTI_CONFIG | 0x12u) /*!< External interrupt line 18 Connected to the USB Wakeup from suspend event */ +#endif /* EXTI_IMR_IM18 */ +#if defined(EXTI_IMR_IM19) +#define EXTI_LINE_19 (EXTI_CONFIG | 0x13u) /*!< External interrupt line 19 Connected to the Ethernet Wakeup event */ +#endif /* EXTI_IMR_IM19 */ + +/** + * @} + */ + +/** @defgroup EXTI_Mode EXTI Mode + * @{ + */ +#define EXTI_MODE_NONE 0x00000000u +#define EXTI_MODE_INTERRUPT 0x00000001u +#define EXTI_MODE_EVENT 0x00000002u +/** + * @} + */ + +/** @defgroup EXTI_Trigger EXTI Trigger + * @{ + */ +#define EXTI_TRIGGER_NONE 0x00000000u +#define EXTI_TRIGGER_RISING 0x00000001u +#define EXTI_TRIGGER_FALLING 0x00000002u +#define EXTI_TRIGGER_RISING_FALLING (EXTI_TRIGGER_RISING | EXTI_TRIGGER_FALLING) +/** + * @} + */ + +/** @defgroup EXTI_GPIOSel EXTI GPIOSel + * @brief + * @{ + */ +#define EXTI_GPIOA 0x00000000u +#define EXTI_GPIOB 0x00000001u +#define EXTI_GPIOC 0x00000002u +#define EXTI_GPIOD 0x00000003u +#if defined (GPIOE) +#define EXTI_GPIOE 0x00000004u +#endif /* GPIOE */ +#if defined (GPIOF) +#define EXTI_GPIOF 0x00000005u +#endif /* GPIOF */ +#if defined (GPIOG) +#define EXTI_GPIOG 0x00000006u +#endif /* GPIOG */ +/** + * @} + */ + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup EXTI_Exported_Macros EXTI Exported Macros + * @{ + */ + +/** + * @} + */ + +/* Private constants --------------------------------------------------------*/ +/** @defgroup EXTI_Private_Constants EXTI Private Constants + * @{ + */ +/** + * @brief EXTI Line property definition + */ +#define EXTI_PROPERTY_SHIFT 24u +#define EXTI_CONFIG (0x02uL << EXTI_PROPERTY_SHIFT) +#define EXTI_GPIO ((0x04uL << EXTI_PROPERTY_SHIFT) | EXTI_CONFIG) +#define EXTI_PROPERTY_MASK (EXTI_CONFIG | EXTI_GPIO) + +/** + * @brief EXTI bit usage + */ +#define EXTI_PIN_MASK 0x0000001Fu + +/** + * @brief EXTI Mask for interrupt & event mode + */ +#define EXTI_MODE_MASK (EXTI_MODE_EVENT | EXTI_MODE_INTERRUPT) + +/** + * @brief EXTI Mask for trigger possibilities + */ +#define EXTI_TRIGGER_MASK (EXTI_TRIGGER_RISING | EXTI_TRIGGER_FALLING) + +/** + * @brief EXTI Line number + */ +#if defined(EXTI_IMR_IM19) +#define EXTI_LINE_NB 20UL +#elif defined(EXTI_IMR_IM18) +#define EXTI_LINE_NB 19UL +#else /* EXTI_IMR_IM17 */ +#define EXTI_LINE_NB 18UL +#endif /* EXTI_IMR_IM19 */ +/** + * @} + */ + +/* Private macros ------------------------------------------------------------*/ +/** @defgroup EXTI_Private_Macros EXTI Private Macros + * @{ + */ +#define IS_EXTI_LINE(__LINE__) ((((__LINE__) & ~(EXTI_PROPERTY_MASK | EXTI_PIN_MASK)) == 0x00u) && \ + ((((__LINE__) & EXTI_PROPERTY_MASK) == EXTI_CONFIG) || \ + (((__LINE__) & EXTI_PROPERTY_MASK) == EXTI_GPIO)) && \ + (((__LINE__) & EXTI_PIN_MASK) < EXTI_LINE_NB)) + +#define IS_EXTI_MODE(__LINE__) ((((__LINE__) & EXTI_MODE_MASK) != 0x00u) && \ + (((__LINE__) & ~EXTI_MODE_MASK) == 0x00u)) + +#define IS_EXTI_TRIGGER(__LINE__) (((__LINE__) & ~EXTI_TRIGGER_MASK) == 0x00u) + +#define IS_EXTI_PENDING_EDGE(__LINE__) ((__LINE__) == EXTI_TRIGGER_RISING_FALLING) + +#define IS_EXTI_CONFIG_LINE(__LINE__) (((__LINE__) & EXTI_CONFIG) != 0x00u) + +#if defined (GPIOG) +#define IS_EXTI_GPIO_PORT(__PORT__) (((__PORT__) == EXTI_GPIOA) || \ + ((__PORT__) == EXTI_GPIOB) || \ + ((__PORT__) == EXTI_GPIOC) || \ + ((__PORT__) == EXTI_GPIOD) || \ + ((__PORT__) == EXTI_GPIOE) || \ + ((__PORT__) == EXTI_GPIOF) || \ + ((__PORT__) == EXTI_GPIOG)) +#elif defined (GPIOF) +#define IS_EXTI_GPIO_PORT(__PORT__) (((__PORT__) == EXTI_GPIOA) || \ + ((__PORT__) == EXTI_GPIOB) || \ + ((__PORT__) == EXTI_GPIOC) || \ + ((__PORT__) == EXTI_GPIOD) || \ + ((__PORT__) == EXTI_GPIOE) || \ + ((__PORT__) == EXTI_GPIOF)) +#elif defined (GPIOE) +#define IS_EXTI_GPIO_PORT(__PORT__) (((__PORT__) == EXTI_GPIOA) || \ + ((__PORT__) == EXTI_GPIOB) || \ + ((__PORT__) == EXTI_GPIOC) || \ + ((__PORT__) == EXTI_GPIOD) || \ + ((__PORT__) == EXTI_GPIOE)) +#else +#define IS_EXTI_GPIO_PORT(__PORT__) (((__PORT__) == EXTI_GPIOA) || \ + ((__PORT__) == EXTI_GPIOB) || \ + ((__PORT__) == EXTI_GPIOC) || \ + ((__PORT__) == EXTI_GPIOD)) +#endif /* GPIOG */ + +#define IS_EXTI_GPIO_PIN(__PIN__) ((__PIN__) < 16u) + +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ +/** @defgroup EXTI_Exported_Functions EXTI Exported Functions + * @brief EXTI Exported Functions + * @{ + */ + +/** @defgroup EXTI_Exported_Functions_Group1 Configuration functions + * @brief Configuration functions + * @{ + */ +/* Configuration functions ****************************************************/ +HAL_StatusTypeDef HAL_EXTI_SetConfigLine(EXTI_HandleTypeDef* hexti, EXTI_ConfigTypeDef* pExtiConfig); +HAL_StatusTypeDef HAL_EXTI_GetConfigLine(EXTI_HandleTypeDef* hexti, EXTI_ConfigTypeDef* pExtiConfig); +HAL_StatusTypeDef HAL_EXTI_ClearConfigLine(EXTI_HandleTypeDef* hexti); +HAL_StatusTypeDef HAL_EXTI_RegisterCallback(EXTI_HandleTypeDef* hexti, EXTI_CallbackIDTypeDef CallbackID, void (*pPendingCbfn)(void)); +HAL_StatusTypeDef HAL_EXTI_GetHandle(EXTI_HandleTypeDef* hexti, uint32_t ExtiLine); +/** + * @} + */ + +/** @defgroup EXTI_Exported_Functions_Group2 IO operation functions + * @brief IO operation functions + * @{ + */ +/* IO operation functions *****************************************************/ +void HAL_EXTI_IRQHandler(EXTI_HandleTypeDef* hexti); +uint32_t HAL_EXTI_GetPending(EXTI_HandleTypeDef* hexti, uint32_t Edge); +void HAL_EXTI_ClearPending(EXTI_HandleTypeDef* hexti, uint32_t Edge); +void HAL_EXTI_GenerateSWI(EXTI_HandleTypeDef* hexti); + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* STM32F1xx_HAL_EXTI_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_flash.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_flash.h new file mode 100644 index 00000000..af855aac --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_flash.h @@ -0,0 +1,328 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_flash.h + * @author MCD Application Team + * @brief Header file of Flash HAL module. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F1xx_HAL_FLASH_H +#define __STM32F1xx_HAL_FLASH_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal_def.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @addtogroup FLASH + * @{ + */ + +/** @addtogroup FLASH_Private_Constants + * @{ + */ +#define FLASH_TIMEOUT_VALUE 50000U /* 50 s */ +/** + * @} + */ + +/** @addtogroup FLASH_Private_Macros + * @{ + */ + +#define IS_FLASH_TYPEPROGRAM(VALUE) (((VALUE) == FLASH_TYPEPROGRAM_HALFWORD) || \ + ((VALUE) == FLASH_TYPEPROGRAM_WORD) || \ + ((VALUE) == FLASH_TYPEPROGRAM_DOUBLEWORD)) + +#if defined(FLASH_ACR_LATENCY) +#define IS_FLASH_LATENCY(__LATENCY__) (((__LATENCY__) == FLASH_LATENCY_0) || \ + ((__LATENCY__) == FLASH_LATENCY_1) || \ + ((__LATENCY__) == FLASH_LATENCY_2)) + +#else +#define IS_FLASH_LATENCY(__LATENCY__) ((__LATENCY__) == FLASH_LATENCY_0) +#endif /* FLASH_ACR_LATENCY */ +/** + * @} + */ + +/* Exported types ------------------------------------------------------------*/ +/** @defgroup FLASH_Exported_Types FLASH Exported Types + * @{ + */ + +/** + * @brief FLASH Procedure structure definition + */ +typedef enum +{ + FLASH_PROC_NONE = 0U, + FLASH_PROC_PAGEERASE = 1U, + FLASH_PROC_MASSERASE = 2U, + FLASH_PROC_PROGRAMHALFWORD = 3U, + FLASH_PROC_PROGRAMWORD = 4U, + FLASH_PROC_PROGRAMDOUBLEWORD = 5U +} FLASH_ProcedureTypeDef; + +/** + * @brief FLASH handle Structure definition + */ +typedef struct +{ + __IO FLASH_ProcedureTypeDef ProcedureOnGoing; /*!< Internal variable to indicate which procedure is ongoing or not in IT context */ + + __IO uint32_t DataRemaining; /*!< Internal variable to save the remaining pages to erase or half-word to program in IT context */ + + __IO uint32_t Address; /*!< Internal variable to save address selected for program or erase */ + + __IO uint64_t Data; /*!< Internal variable to save data to be programmed */ + + HAL_LockTypeDef Lock; /*!< FLASH locking object */ + + __IO uint32_t ErrorCode; /*!< FLASH error code + This parameter can be a value of @ref FLASH_Error_Codes */ +} FLASH_ProcessTypeDef; + +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup FLASH_Exported_Constants FLASH Exported Constants + * @{ + */ + +/** @defgroup FLASH_Error_Codes FLASH Error Codes + * @{ + */ + +#define HAL_FLASH_ERROR_NONE 0x00U /*!< No error */ +#define HAL_FLASH_ERROR_PROG 0x01U /*!< Programming error */ +#define HAL_FLASH_ERROR_WRP 0x02U /*!< Write protection error */ +#define HAL_FLASH_ERROR_OPTV 0x04U /*!< Option validity error */ + +/** + * @} + */ + +/** @defgroup FLASH_Type_Program FLASH Type Program + * @{ + */ +#define FLASH_TYPEPROGRAM_HALFWORD 0x01U /*!ACR |= FLASH_ACR_HLFCYA) + +/** + * @brief Disable the FLASH half cycle access. + * @note half cycle access can only be used with a low-frequency clock of less than + 8 MHz that can be obtained with the use of HSI or HSE but not of PLL. + * @retval None + */ +#define __HAL_FLASH_HALF_CYCLE_ACCESS_DISABLE() (FLASH->ACR &= (~FLASH_ACR_HLFCYA)) + +/** + * @} + */ + +#if defined(FLASH_ACR_LATENCY) +/** @defgroup FLASH_EM_Latency FLASH Latency + * @brief macros to handle FLASH Latency + * @{ + */ + +/** + * @brief Set the FLASH Latency. + * @param __LATENCY__ FLASH Latency + * The value of this parameter depend on device used within the same series + * @retval None + */ +#define __HAL_FLASH_SET_LATENCY(__LATENCY__) (FLASH->ACR = (FLASH->ACR&(~FLASH_ACR_LATENCY)) | (__LATENCY__)) + + +/** + * @brief Get the FLASH Latency. + * @retval FLASH Latency + * The value of this parameter depend on device used within the same series + */ +#define __HAL_FLASH_GET_LATENCY() (READ_BIT((FLASH->ACR), FLASH_ACR_LATENCY)) + +/** + * @} + */ + +#endif /* FLASH_ACR_LATENCY */ +/** @defgroup FLASH_Prefetch FLASH Prefetch + * @brief macros to handle FLASH Prefetch buffer + * @{ + */ +/** + * @brief Enable the FLASH prefetch buffer. + * @retval None + */ +#define __HAL_FLASH_PREFETCH_BUFFER_ENABLE() (FLASH->ACR |= FLASH_ACR_PRFTBE) + +/** + * @brief Disable the FLASH prefetch buffer. + * @retval None + */ +#define __HAL_FLASH_PREFETCH_BUFFER_DISABLE() (FLASH->ACR &= (~FLASH_ACR_PRFTBE)) + +/** + * @} + */ + +/** + * @} + */ + +/* Include FLASH HAL Extended module */ +#include "stm32f1xx_hal_flash_ex.h" + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup FLASH_Exported_Functions + * @{ + */ + +/** @addtogroup FLASH_Exported_Functions_Group1 + * @{ + */ +/* IO operation functions *****************************************************/ +HAL_StatusTypeDef HAL_FLASH_Program(uint32_t TypeProgram, uint32_t Address, uint64_t Data); +HAL_StatusTypeDef HAL_FLASH_Program_IT(uint32_t TypeProgram, uint32_t Address, uint64_t Data); + +/* FLASH IRQ handler function */ +void HAL_FLASH_IRQHandler(void); +/* Callbacks in non blocking modes */ +void HAL_FLASH_EndOfOperationCallback(uint32_t ReturnValue); +void HAL_FLASH_OperationErrorCallback(uint32_t ReturnValue); + +/** + * @} + */ + +/** @addtogroup FLASH_Exported_Functions_Group2 + * @{ + */ +/* Peripheral Control functions ***********************************************/ +HAL_StatusTypeDef HAL_FLASH_Unlock(void); +HAL_StatusTypeDef HAL_FLASH_Lock(void); +HAL_StatusTypeDef HAL_FLASH_OB_Unlock(void); +HAL_StatusTypeDef HAL_FLASH_OB_Lock(void); +void HAL_FLASH_OB_Launch(void); + +/** + * @} + */ + +/** @addtogroup FLASH_Exported_Functions_Group3 + * @{ + */ +/* Peripheral State and Error functions ***************************************/ +uint32_t HAL_FLASH_GetError(void); + +/** + * @} + */ + +/** + * @} + */ + +/* Private function -------------------------------------------------*/ +/** @addtogroup FLASH_Private_Functions + * @{ + */ +HAL_StatusTypeDef FLASH_WaitForLastOperation(uint32_t Timeout); +#if defined(FLASH_BANK2_END) +HAL_StatusTypeDef FLASH_WaitForLastOperationBank2(uint32_t Timeout); +#endif /* FLASH_BANK2_END */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F1xx_HAL_FLASH_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ + diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_flash_ex.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_flash_ex.h new file mode 100644 index 00000000..2eea2407 --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_flash_ex.h @@ -0,0 +1,786 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_flash_ex.h + * @author MCD Application Team + * @brief Header file of Flash HAL Extended module. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F1xx_HAL_FLASH_EX_H +#define __STM32F1xx_HAL_FLASH_EX_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal_def.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @addtogroup FLASHEx + * @{ + */ + +/** @addtogroup FLASHEx_Private_Constants + * @{ + */ + +#define FLASH_SIZE_DATA_REGISTER 0x1FFFF7E0U +#define OBR_REG_INDEX 1U +#define SR_FLAG_MASK ((uint32_t)(FLASH_SR_BSY | FLASH_SR_PGERR | FLASH_SR_WRPRTERR | FLASH_SR_EOP)) + +/** + * @} + */ + +/** @addtogroup FLASHEx_Private_Macros + * @{ + */ + +#define IS_FLASH_TYPEERASE(VALUE) (((VALUE) == FLASH_TYPEERASE_PAGES) || ((VALUE) == FLASH_TYPEERASE_MASSERASE)) + +#define IS_OPTIONBYTE(VALUE) (((VALUE) <= (OPTIONBYTE_WRP | OPTIONBYTE_RDP | OPTIONBYTE_USER | OPTIONBYTE_DATA))) + +#define IS_WRPSTATE(VALUE) (((VALUE) == OB_WRPSTATE_DISABLE) || ((VALUE) == OB_WRPSTATE_ENABLE)) + +#define IS_OB_RDP_LEVEL(LEVEL) (((LEVEL) == OB_RDP_LEVEL_0) || ((LEVEL) == OB_RDP_LEVEL_1)) + +#define IS_OB_DATA_ADDRESS(ADDRESS) (((ADDRESS) == OB_DATA_ADDRESS_DATA0) || ((ADDRESS) == OB_DATA_ADDRESS_DATA1)) + +#define IS_OB_IWDG_SOURCE(SOURCE) (((SOURCE) == OB_IWDG_SW) || ((SOURCE) == OB_IWDG_HW)) + +#define IS_OB_STOP_SOURCE(SOURCE) (((SOURCE) == OB_STOP_NO_RST) || ((SOURCE) == OB_STOP_RST)) + +#define IS_OB_STDBY_SOURCE(SOURCE) (((SOURCE) == OB_STDBY_NO_RST) || ((SOURCE) == OB_STDBY_RST)) + +#if defined(FLASH_BANK2_END) +#define IS_OB_BOOT1(BOOT1) (((BOOT1) == OB_BOOT1_RESET) || ((BOOT1) == OB_BOOT1_SET)) +#endif /* FLASH_BANK2_END */ + +/* Low Density */ +#if (defined(STM32F101x6) || defined(STM32F102x6) || defined(STM32F103x6)) +#define IS_FLASH_NB_PAGES(ADDRESS,NBPAGES) (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x20U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)- 1 <= 0x08007FFFU) : \ + ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)- 1 <= 0x08003FFFU)) +#endif /* STM32F101x6 || STM32F102x6 || STM32F103x6 */ + +/* Medium Density */ +#if (defined(STM32F100xB) || defined(STM32F101xB) || defined(STM32F102xB) || defined(STM32F103xB)) +#define IS_FLASH_NB_PAGES(ADDRESS,NBPAGES) (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x80U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0801FFFFU) : \ + (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x40U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0800FFFFU) : \ + (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x20U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x08007FFFU) : \ + ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x08003FFFU)))) +#endif /* STM32F100xB || STM32F101xB || STM32F102xB || STM32F103xB*/ + +/* High Density */ +#if (defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F103xE)) +#define IS_FLASH_NB_PAGES(ADDRESS,NBPAGES) (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x200U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0807FFFFU) : \ + (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x180U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0805FFFFU) : \ + ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0803FFFFU))) +#endif /* STM32F100xE || STM32F101xE || STM32F103xE */ + +/* XL Density */ +#if defined(FLASH_BANK2_END) +#define IS_FLASH_NB_PAGES(ADDRESS,NBPAGES) (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x400U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x080FFFFFU) : \ + ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x080BFFFFU)) +#endif /* FLASH_BANK2_END */ + +/* Connectivity Line */ +#if (defined(STM32F105xC) || defined(STM32F107xC)) +#define IS_FLASH_NB_PAGES(ADDRESS,NBPAGES) (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x100U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0803FFFFU) : \ + (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x80U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0801FFFFU) : \ + ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0800FFFFU))) +#endif /* STM32F105xC || STM32F107xC */ + +#define IS_OB_WRP(PAGE) (((PAGE) != 0x0000000U)) + +#if defined(FLASH_BANK2_END) +#define IS_FLASH_BANK(BANK) (((BANK) == FLASH_BANK_1) || \ + ((BANK) == FLASH_BANK_2) || \ + ((BANK) == FLASH_BANK_BOTH)) +#else +#define IS_FLASH_BANK(BANK) (((BANK) == FLASH_BANK_1)) +#endif /* FLASH_BANK2_END */ + +/* Low Density */ +#if (defined(STM32F101x6) || defined(STM32F102x6) || defined(STM32F103x6)) +#define IS_FLASH_PROGRAM_ADDRESS(ADDRESS) (((ADDRESS) >= FLASH_BASE) && (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x20U) ? \ + ((ADDRESS) <= FLASH_BANK1_END) : ((ADDRESS) <= 0x08003FFFU))) + +#endif /* STM32F101x6 || STM32F102x6 || STM32F103x6 */ + +/* Medium Density */ +#if (defined(STM32F100xB) || defined(STM32F101xB) || defined(STM32F102xB) || defined(STM32F103xB)) +#define IS_FLASH_PROGRAM_ADDRESS(ADDRESS) (((ADDRESS) >= FLASH_BASE) && (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x80U) ? \ + ((ADDRESS) <= FLASH_BANK1_END) : (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x40U) ? \ + ((ADDRESS) <= 0x0800FFFF) : (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x20U) ? \ + ((ADDRESS) <= 0x08007FFF) : ((ADDRESS) <= 0x08003FFFU))))) + +#endif /* STM32F100xB || STM32F101xB || STM32F102xB || STM32F103xB*/ + +/* High Density */ +#if (defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F103xE)) +#define IS_FLASH_PROGRAM_ADDRESS(ADDRESS) (((ADDRESS) >= FLASH_BASE) && (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x200U) ? \ + ((ADDRESS) <= FLASH_BANK1_END) : (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x180U) ? \ + ((ADDRESS) <= 0x0805FFFFU) : ((ADDRESS) <= 0x0803FFFFU)))) + +#endif /* STM32F100xE || STM32F101xE || STM32F103xE */ + +/* XL Density */ +#if defined(FLASH_BANK2_END) +#define IS_FLASH_PROGRAM_ADDRESS(ADDRESS) (((ADDRESS) >= FLASH_BASE) && (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x400U) ? \ + ((ADDRESS) <= FLASH_BANK2_END) : ((ADDRESS) <= 0x080BFFFFU))) + +#endif /* FLASH_BANK2_END */ + +/* Connectivity Line */ +#if (defined(STM32F105xC) || defined(STM32F107xC)) +#define IS_FLASH_PROGRAM_ADDRESS(ADDRESS) (((ADDRESS) >= FLASH_BASE) && (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x100U) ? \ + ((ADDRESS) <= FLASH_BANK1_END) : (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x80U) ? \ + ((ADDRESS) <= 0x0801FFFFU) : ((ADDRESS) <= 0x0800FFFFU)))) + +#endif /* STM32F105xC || STM32F107xC */ + +/** + * @} + */ + +/* Exported types ------------------------------------------------------------*/ +/** @defgroup FLASHEx_Exported_Types FLASHEx Exported Types + * @{ + */ + +/** + * @brief FLASH Erase structure definition + */ +typedef struct +{ + uint32_t TypeErase; /*!< TypeErase: Mass erase or page erase. + This parameter can be a value of @ref FLASHEx_Type_Erase */ + + uint32_t Banks; /*!< Select banks to erase when Mass erase is enabled. + This parameter must be a value of @ref FLASHEx_Banks */ + + uint32_t PageAddress; /*!< PageAdress: Initial FLASH page address to erase when mass erase is disabled + This parameter must be a number between Min_Data = 0x08000000 and Max_Data = FLASH_BANKx_END + (x = 1 or 2 depending on devices)*/ + + uint32_t NbPages; /*!< NbPages: Number of pagess to be erased. + This parameter must be a value between Min_Data = 1 and Max_Data = (max number of pages - value of initial page)*/ + +} FLASH_EraseInitTypeDef; + +/** + * @brief FLASH Options bytes program structure definition + */ +typedef struct +{ + uint32_t OptionType; /*!< OptionType: Option byte to be configured. + This parameter can be a value of @ref FLASHEx_OB_Type */ + + uint32_t WRPState; /*!< WRPState: Write protection activation or deactivation. + This parameter can be a value of @ref FLASHEx_OB_WRP_State */ + + uint32_t WRPPage; /*!< WRPPage: specifies the page(s) to be write protected + This parameter can be a value of @ref FLASHEx_OB_Write_Protection */ + + uint32_t Banks; /*!< Select banks for WRP activation/deactivation of all sectors. + This parameter must be a value of @ref FLASHEx_Banks */ + + uint8_t RDPLevel; /*!< RDPLevel: Set the read protection level.. + This parameter can be a value of @ref FLASHEx_OB_Read_Protection */ + +#if defined(FLASH_BANK2_END) + uint8_t USERConfig; /*!< USERConfig: Program the FLASH User Option Byte: + IWDG / STOP / STDBY / BOOT1 + This parameter can be a combination of @ref FLASHEx_OB_IWatchdog, @ref FLASHEx_OB_nRST_STOP, + @ref FLASHEx_OB_nRST_STDBY, @ref FLASHEx_OB_BOOT1 */ +#else + uint8_t USERConfig; /*!< USERConfig: Program the FLASH User Option Byte: + IWDG / STOP / STDBY + This parameter can be a combination of @ref FLASHEx_OB_IWatchdog, @ref FLASHEx_OB_nRST_STOP, + @ref FLASHEx_OB_nRST_STDBY */ +#endif /* FLASH_BANK2_END */ + + uint32_t DATAAddress; /*!< DATAAddress: Address of the option byte DATA to be programmed + This parameter can be a value of @ref FLASHEx_OB_Data_Address */ + + uint8_t DATAData; /*!< DATAData: Data to be stored in the option byte DATA + This parameter must be a number between Min_Data = 0x00 and Max_Data = 0xFF */ +} FLASH_OBProgramInitTypeDef; + +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup FLASHEx_Exported_Constants FLASHEx Exported Constants + * @{ + */ + +/** @defgroup FLASHEx_Constants FLASH Constants + * @{ + */ + +/** @defgroup FLASHEx_Page_Size Page Size + * @{ + */ +#if (defined(STM32F101x6) || defined(STM32F102x6) || defined(STM32F103x6) || defined(STM32F100xB) || defined(STM32F101xB) || defined(STM32F102xB) || defined(STM32F103xB)) +#define FLASH_PAGE_SIZE 0x400U +#endif /* STM32F101x6 || STM32F102x6 || STM32F103x6 */ +/* STM32F100xB || STM32F101xB || STM32F102xB || STM32F103xB */ + +#if (defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F103xE) || defined(STM32F101xG) || defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC)) +#define FLASH_PAGE_SIZE 0x800U +#endif /* STM32F100xB || STM32F101xB || STM32F102xB || STM32F103xB */ +/* STM32F101xG || STM32F103xG */ +/* STM32F105xC || STM32F107xC */ + +/** + * @} + */ + +/** @defgroup FLASHEx_Type_Erase Type Erase + * @{ + */ +#define FLASH_TYPEERASE_PAGES 0x00U /*!CR, ((__INTERRUPT__) & 0x0000FFFFU)); \ + /* Enable Bank2 IT */ \ + SET_BIT(FLASH->CR2, ((__INTERRUPT__) >> 16U)); \ + } while(0U) + +/** + * @brief Disable the specified FLASH interrupt. + * @param __INTERRUPT__ FLASH interrupt + * This parameter can be any combination of the following values: + * @arg @ref FLASH_IT_EOP_BANK1 End of FLASH Operation Interrupt on bank1 + * @arg @ref FLASH_IT_ERR_BANK1 Error Interrupt on bank1 + * @arg @ref FLASH_IT_EOP_BANK2 End of FLASH Operation Interrupt on bank2 + * @arg @ref FLASH_IT_ERR_BANK2 Error Interrupt on bank2 + * @retval none + */ +#define __HAL_FLASH_DISABLE_IT(__INTERRUPT__) do { \ + /* Disable Bank1 IT */ \ + CLEAR_BIT(FLASH->CR, ((__INTERRUPT__) & 0x0000FFFFU)); \ + /* Disable Bank2 IT */ \ + CLEAR_BIT(FLASH->CR2, ((__INTERRUPT__) >> 16U)); \ + } while(0U) + +/** + * @brief Get the specified FLASH flag status. + * @param __FLAG__ specifies the FLASH flag to check. + * This parameter can be one of the following values: + * @arg @ref FLASH_FLAG_EOP_BANK1 FLASH End of Operation flag on bank1 + * @arg @ref FLASH_FLAG_WRPERR_BANK1 FLASH Write protected error flag on bank1 + * @arg @ref FLASH_FLAG_PGERR_BANK1 FLASH Programming error flag on bank1 + * @arg @ref FLASH_FLAG_BSY_BANK1 FLASH Busy flag on bank1 + * @arg @ref FLASH_FLAG_EOP_BANK2 FLASH End of Operation flag on bank2 + * @arg @ref FLASH_FLAG_WRPERR_BANK2 FLASH Write protected error flag on bank2 + * @arg @ref FLASH_FLAG_PGERR_BANK2 FLASH Programming error flag on bank2 + * @arg @ref FLASH_FLAG_BSY_BANK2 FLASH Busy flag on bank2 + * @arg @ref FLASH_FLAG_OPTVERR Loaded OB and its complement do not match + * @retval The new state of __FLAG__ (SET or RESET). + */ +#define __HAL_FLASH_GET_FLAG(__FLAG__) (((__FLAG__) == FLASH_FLAG_OPTVERR) ? \ + (FLASH->OBR & FLASH_OBR_OPTERR) : \ + ((((__FLAG__) & SR_FLAG_MASK) != RESET)? \ + (FLASH->SR & ((__FLAG__) & SR_FLAG_MASK)) : \ + (FLASH->SR2 & ((__FLAG__) >> 16U)))) + +/** + * @brief Clear the specified FLASH flag. + * @param __FLAG__ specifies the FLASH flags to clear. + * This parameter can be any combination of the following values: + * @arg @ref FLASH_FLAG_EOP_BANK1 FLASH End of Operation flag on bank1 + * @arg @ref FLASH_FLAG_WRPERR_BANK1 FLASH Write protected error flag on bank1 + * @arg @ref FLASH_FLAG_PGERR_BANK1 FLASH Programming error flag on bank1 + * @arg @ref FLASH_FLAG_BSY_BANK1 FLASH Busy flag on bank1 + * @arg @ref FLASH_FLAG_EOP_BANK2 FLASH End of Operation flag on bank2 + * @arg @ref FLASH_FLAG_WRPERR_BANK2 FLASH Write protected error flag on bank2 + * @arg @ref FLASH_FLAG_PGERR_BANK2 FLASH Programming error flag on bank2 + * @arg @ref FLASH_FLAG_BSY_BANK2 FLASH Busy flag on bank2 + * @arg @ref FLASH_FLAG_OPTVERR Loaded OB and its complement do not match + * @retval none + */ +#define __HAL_FLASH_CLEAR_FLAG(__FLAG__) do { \ + /* Clear FLASH_FLAG_OPTVERR flag */ \ + if ((__FLAG__) == FLASH_FLAG_OPTVERR) \ + { \ + CLEAR_BIT(FLASH->OBR, FLASH_OBR_OPTERR); \ + } \ + else { \ + /* Clear Flag in Bank1 */ \ + if (((__FLAG__) & SR_FLAG_MASK) != RESET) \ + { \ + FLASH->SR = ((__FLAG__) & SR_FLAG_MASK); \ + } \ + /* Clear Flag in Bank2 */ \ + if (((__FLAG__) >> 16U) != RESET) \ + { \ + FLASH->SR2 = ((__FLAG__) >> 16U); \ + } \ + } \ + } while(0U) +#else +/** + * @brief Enable the specified FLASH interrupt. + * @param __INTERRUPT__ FLASH interrupt + * This parameter can be any combination of the following values: + * @arg @ref FLASH_IT_EOP End of FLASH Operation Interrupt + * @arg @ref FLASH_IT_ERR Error Interrupt + * @retval none + */ +#define __HAL_FLASH_ENABLE_IT(__INTERRUPT__) (FLASH->CR |= (__INTERRUPT__)) + +/** + * @brief Disable the specified FLASH interrupt. + * @param __INTERRUPT__ FLASH interrupt + * This parameter can be any combination of the following values: + * @arg @ref FLASH_IT_EOP End of FLASH Operation Interrupt + * @arg @ref FLASH_IT_ERR Error Interrupt + * @retval none + */ +#define __HAL_FLASH_DISABLE_IT(__INTERRUPT__) (FLASH->CR &= ~(__INTERRUPT__)) + +/** + * @brief Get the specified FLASH flag status. + * @param __FLAG__ specifies the FLASH flag to check. + * This parameter can be one of the following values: + * @arg @ref FLASH_FLAG_EOP FLASH End of Operation flag + * @arg @ref FLASH_FLAG_WRPERR FLASH Write protected error flag + * @arg @ref FLASH_FLAG_PGERR FLASH Programming error flag + * @arg @ref FLASH_FLAG_BSY FLASH Busy flag + * @arg @ref FLASH_FLAG_OPTVERR Loaded OB and its complement do not match + * @retval The new state of __FLAG__ (SET or RESET). + */ +#define __HAL_FLASH_GET_FLAG(__FLAG__) (((__FLAG__) == FLASH_FLAG_OPTVERR) ? \ + (FLASH->OBR & FLASH_OBR_OPTERR) : \ + (FLASH->SR & (__FLAG__))) +/** + * @brief Clear the specified FLASH flag. + * @param __FLAG__ specifies the FLASH flags to clear. + * This parameter can be any combination of the following values: + * @arg @ref FLASH_FLAG_EOP FLASH End of Operation flag + * @arg @ref FLASH_FLAG_WRPERR FLASH Write protected error flag + * @arg @ref FLASH_FLAG_PGERR FLASH Programming error flag + * @arg @ref FLASH_FLAG_OPTVERR Loaded OB and its complement do not match + * @retval none + */ +#define __HAL_FLASH_CLEAR_FLAG(__FLAG__) do { \ + /* Clear FLASH_FLAG_OPTVERR flag */ \ + if ((__FLAG__) == FLASH_FLAG_OPTVERR) \ + { \ + CLEAR_BIT(FLASH->OBR, FLASH_OBR_OPTERR); \ + } \ + else { \ + /* Clear Flag in Bank1 */ \ + FLASH->SR = (__FLAG__); \ + } \ + } while(0U) + +#endif + +/** + * @} + */ + +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup FLASHEx_Exported_Functions + * @{ + */ + +/** @addtogroup FLASHEx_Exported_Functions_Group1 + * @{ + */ +/* IO operation functions *****************************************************/ +HAL_StatusTypeDef HAL_FLASHEx_Erase(FLASH_EraseInitTypeDef* pEraseInit, uint32_t* PageError); +HAL_StatusTypeDef HAL_FLASHEx_Erase_IT(FLASH_EraseInitTypeDef* pEraseInit); + +/** + * @} + */ + +/** @addtogroup FLASHEx_Exported_Functions_Group2 + * @{ + */ +/* Peripheral Control functions ***********************************************/ +HAL_StatusTypeDef HAL_FLASHEx_OBErase(void); +HAL_StatusTypeDef HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef* pOBInit); +void HAL_FLASHEx_OBGetConfig(FLASH_OBProgramInitTypeDef* pOBInit); +uint32_t HAL_FLASHEx_OBGetUserData(uint32_t DATAAdress); +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F1xx_HAL_FLASH_EX_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_gpio.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_gpio.h similarity index 53% rename from EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_gpio.h rename to EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_gpio.h index 8b1f7d36..f3ada9e8 100644 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_gpio.h +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_gpio.h @@ -1,52 +1,34 @@ /** ****************************************************************************** - * @file stm32f4xx_hal_gpio.h + * @file stm32f1xx_hal_gpio.h * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 * @brief Header file of GPIO HAL module. ****************************************************************************** * @attention * - *

© COPYRIGHT(c) 2016 STMicroelectronics

+ *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

* - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause * ****************************************************************************** */ /* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_GPIO_H -#define __STM32F4xx_HAL_GPIO_H +#ifndef STM32F1xx_HAL_GPIO_H +#define STM32F1xx_HAL_GPIO_H #ifdef __cplusplus extern "C" { #endif /* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_def.h" +#include "stm32f1xx_hal_def.h" -/** @addtogroup STM32F4xx_HAL_Driver +/** @addtogroup STM32F1xx_HAL_Driver * @{ */ @@ -75,9 +57,6 @@ typedef struct uint32_t Speed; /*!< Specifies the speed for the selected pins. This parameter can be a value of @ref GPIO_speed_define */ - - uint32_t Alternate; /*!< Peripheral to be connected to the selected pins. - This parameter can be a value of @ref GPIO_Alternate_function_selection */ } GPIO_InitTypeDef; /** @@ -85,7 +64,7 @@ typedef struct */ typedef enum { - GPIO_PIN_RESET = 0, + GPIO_PIN_RESET = 0u, GPIO_PIN_SET } GPIO_PinState; /** @@ -101,25 +80,25 @@ typedef enum /** @defgroup GPIO_pins_define GPIO pins define * @{ */ -#define GPIO_PIN_0 ((uint16_t)0x0001U) /* Pin 0 selected */ -#define GPIO_PIN_1 ((uint16_t)0x0002U) /* Pin 1 selected */ -#define GPIO_PIN_2 ((uint16_t)0x0004U) /* Pin 2 selected */ -#define GPIO_PIN_3 ((uint16_t)0x0008U) /* Pin 3 selected */ -#define GPIO_PIN_4 ((uint16_t)0x0010U) /* Pin 4 selected */ -#define GPIO_PIN_5 ((uint16_t)0x0020U) /* Pin 5 selected */ -#define GPIO_PIN_6 ((uint16_t)0x0040U) /* Pin 6 selected */ -#define GPIO_PIN_7 ((uint16_t)0x0080U) /* Pin 7 selected */ -#define GPIO_PIN_8 ((uint16_t)0x0100U) /* Pin 8 selected */ -#define GPIO_PIN_9 ((uint16_t)0x0200U) /* Pin 9 selected */ -#define GPIO_PIN_10 ((uint16_t)0x0400U) /* Pin 10 selected */ -#define GPIO_PIN_11 ((uint16_t)0x0800U) /* Pin 11 selected */ -#define GPIO_PIN_12 ((uint16_t)0x1000U) /* Pin 12 selected */ -#define GPIO_PIN_13 ((uint16_t)0x2000U) /* Pin 13 selected */ -#define GPIO_PIN_14 ((uint16_t)0x4000U) /* Pin 14 selected */ -#define GPIO_PIN_15 ((uint16_t)0x8000U) /* Pin 15 selected */ -#define GPIO_PIN_All ((uint16_t)0xFFFFU) /* All pins selected */ - -#define GPIO_PIN_MASK ((uint32_t)0x0000FFFFU) /* PIN mask for assert test */ +#define GPIO_PIN_0 ((uint16_t)0x0001) /* Pin 0 selected */ +#define GPIO_PIN_1 ((uint16_t)0x0002) /* Pin 1 selected */ +#define GPIO_PIN_2 ((uint16_t)0x0004) /* Pin 2 selected */ +#define GPIO_PIN_3 ((uint16_t)0x0008) /* Pin 3 selected */ +#define GPIO_PIN_4 ((uint16_t)0x0010) /* Pin 4 selected */ +#define GPIO_PIN_5 ((uint16_t)0x0020) /* Pin 5 selected */ +#define GPIO_PIN_6 ((uint16_t)0x0040) /* Pin 6 selected */ +#define GPIO_PIN_7 ((uint16_t)0x0080) /* Pin 7 selected */ +#define GPIO_PIN_8 ((uint16_t)0x0100) /* Pin 8 selected */ +#define GPIO_PIN_9 ((uint16_t)0x0200) /* Pin 9 selected */ +#define GPIO_PIN_10 ((uint16_t)0x0400) /* Pin 10 selected */ +#define GPIO_PIN_11 ((uint16_t)0x0800) /* Pin 11 selected */ +#define GPIO_PIN_12 ((uint16_t)0x1000) /* Pin 12 selected */ +#define GPIO_PIN_13 ((uint16_t)0x2000) /* Pin 13 selected */ +#define GPIO_PIN_14 ((uint16_t)0x4000) /* Pin 14 selected */ +#define GPIO_PIN_15 ((uint16_t)0x8000) /* Pin 15 selected */ +#define GPIO_PIN_All ((uint16_t)0xFFFF) /* All pins selected */ + +#define GPIO_PIN_MASK 0x0000FFFFu /* PIN mask for assert test */ /** * @} */ @@ -134,21 +113,23 @@ typedef enum * - Z : IO Direction mode (Input, Output, Alternate or Analog) * @{ */ -#define GPIO_MODE_INPUT ((uint32_t)0x00000000U) /*!< Input Floating Mode */ -#define GPIO_MODE_OUTPUT_PP ((uint32_t)0x00000001U) /*!< Output Push Pull Mode */ -#define GPIO_MODE_OUTPUT_OD ((uint32_t)0x00000011U) /*!< Output Open Drain Mode */ -#define GPIO_MODE_AF_PP ((uint32_t)0x00000002U) /*!< Alternate Function Push Pull Mode */ -#define GPIO_MODE_AF_OD ((uint32_t)0x00000012U) /*!< Alternate Function Open Drain Mode */ +#define GPIO_MODE_INPUT 0x00000000u /*!< Input Floating Mode */ +#define GPIO_MODE_OUTPUT_PP 0x00000001u /*!< Output Push Pull Mode */ +#define GPIO_MODE_OUTPUT_OD 0x00000011u /*!< Output Open Drain Mode */ +#define GPIO_MODE_AF_PP 0x00000002u /*!< Alternate Function Push Pull Mode */ +#define GPIO_MODE_AF_OD 0x00000012u /*!< Alternate Function Open Drain Mode */ +#define GPIO_MODE_AF_INPUT GPIO_MODE_INPUT /*!< Alternate Function Input Mode */ -#define GPIO_MODE_ANALOG ((uint32_t)0x00000003U) /*!< Analog Mode */ +#define GPIO_MODE_ANALOG 0x00000003u /*!< Analog Mode */ -#define GPIO_MODE_IT_RISING ((uint32_t)0x10110000U) /*!< External Interrupt Mode with Rising edge trigger detection */ -#define GPIO_MODE_IT_FALLING ((uint32_t)0x10210000U) /*!< External Interrupt Mode with Falling edge trigger detection */ -#define GPIO_MODE_IT_RISING_FALLING ((uint32_t)0x10310000U) /*!< External Interrupt Mode with Rising/Falling edge trigger detection */ +#define GPIO_MODE_IT_RISING 0x10110000u /*!< External Interrupt Mode with Rising edge trigger detection */ +#define GPIO_MODE_IT_FALLING 0x10210000u /*!< External Interrupt Mode with Falling edge trigger detection */ +#define GPIO_MODE_IT_RISING_FALLING 0x10310000u /*!< External Interrupt Mode with Rising/Falling edge trigger detection */ + +#define GPIO_MODE_EVT_RISING 0x10120000u /*!< External Event Mode with Rising edge trigger detection */ +#define GPIO_MODE_EVT_FALLING 0x10220000u /*!< External Event Mode with Falling edge trigger detection */ +#define GPIO_MODE_EVT_RISING_FALLING 0x10320000u /*!< External Event Mode with Rising/Falling edge trigger detection */ -#define GPIO_MODE_EVT_RISING ((uint32_t)0x10120000U) /*!< External Event Mode with Rising edge trigger detection */ -#define GPIO_MODE_EVT_FALLING ((uint32_t)0x10220000U) /*!< External Event Mode with Falling edge trigger detection */ -#define GPIO_MODE_EVT_RISING_FALLING ((uint32_t)0x10320000U) /*!< External Event Mode with Rising/Falling edge trigger detection */ /** * @} */ @@ -157,10 +138,10 @@ typedef enum * @brief GPIO Output Maximum frequency * @{ */ -#define GPIO_SPEED_FREQ_LOW ((uint32_t)0x00000000U) /*!< IO works at 2 MHz, please refer to the product datasheet */ -#define GPIO_SPEED_FREQ_MEDIUM ((uint32_t)0x00000001U) /*!< range 12,5 MHz to 50 MHz, please refer to the product datasheet */ -#define GPIO_SPEED_FREQ_HIGH ((uint32_t)0x00000002U) /*!< range 25 MHz to 100 MHz, please refer to the product datasheet */ -#define GPIO_SPEED_FREQ_VERY_HIGH ((uint32_t)0x00000003U) /*!< range 50 MHz to 200 MHz, please refer to the product datasheet */ +#define GPIO_SPEED_FREQ_LOW (GPIO_CRL_MODE0_1) /*!< Low speed */ +#define GPIO_SPEED_FREQ_MEDIUM (GPIO_CRL_MODE0_0) /*!< Medium speed */ +#define GPIO_SPEED_FREQ_HIGH (GPIO_CRL_MODE0) /*!< High speed */ + /** * @} */ @@ -169,9 +150,9 @@ typedef enum * @brief GPIO Pull-Up or Pull-Down Activation * @{ */ -#define GPIO_NOPULL ((uint32_t)0x00000000U) /*!< No Pull-up or Pull-down activation */ -#define GPIO_PULLUP ((uint32_t)0x00000001U) /*!< Pull-up activation */ -#define GPIO_PULLDOWN ((uint32_t)0x00000002U) /*!< Pull-down activation */ +#define GPIO_NOPULL 0x00000000u /*!< No Pull-up or Pull-down activation */ +#define GPIO_PULLUP 0x00000001u /*!< Pull-up activation */ +#define GPIO_PULLDOWN 0x00000002u /*!< Pull-down activation */ /** * @} */ @@ -229,7 +210,7 @@ typedef enum */ /* Include GPIO HAL Extension module */ -#include "stm32f4xx_hal_gpio_ex.h" +#include "stm32f1xx_hal_gpio_ex.h" /* Exported functions --------------------------------------------------------*/ /** @addtogroup GPIO_Exported_Functions @@ -280,7 +261,7 @@ void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin); * @{ */ #define IS_GPIO_PIN_ACTION(ACTION) (((ACTION) == GPIO_PIN_RESET) || ((ACTION) == GPIO_PIN_SET)) -#define IS_GPIO_PIN(PIN) (((PIN) & GPIO_PIN_MASK ) != (uint32_t)0x00U) +#define IS_GPIO_PIN(PIN) (((((uint32_t)PIN) & GPIO_PIN_MASK ) != 0x00u) && ((((uint32_t)PIN) & ~GPIO_PIN_MASK) == 0x00u)) #define IS_GPIO_MODE(MODE) (((MODE) == GPIO_MODE_INPUT) ||\ ((MODE) == GPIO_MODE_OUTPUT_PP) ||\ ((MODE) == GPIO_MODE_OUTPUT_OD) ||\ @@ -293,8 +274,8 @@ void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin); ((MODE) == GPIO_MODE_EVT_FALLING) ||\ ((MODE) == GPIO_MODE_EVT_RISING_FALLING) ||\ ((MODE) == GPIO_MODE_ANALOG)) -#define IS_GPIO_SPEED(SPEED) (((SPEED) == GPIO_SPEED_FREQ_LOW) || ((SPEED) == GPIO_SPEED_FREQ_MEDIUM) || \ - ((SPEED) == GPIO_SPEED_FREQ_HIGH) || ((SPEED) == GPIO_SPEED_FREQ_VERY_HIGH)) +#define IS_GPIO_SPEED(SPEED) (((SPEED) == GPIO_SPEED_FREQ_LOW) || \ + ((SPEED) == GPIO_SPEED_FREQ_MEDIUM) || ((SPEED) == GPIO_SPEED_FREQ_HIGH)) #define IS_GPIO_PULL(PULL) (((PULL) == GPIO_NOPULL) || ((PULL) == GPIO_PULLUP) || \ ((PULL) == GPIO_PULLDOWN)) /** @@ -322,6 +303,6 @@ void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin); } #endif -#endif /* __STM32F4xx_HAL_GPIO_H */ +#endif /* STM32F1xx_HAL_GPIO_H */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_gpio_ex.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_gpio_ex.h new file mode 100644 index 00000000..5f6c3fd4 --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_gpio_ex.h @@ -0,0 +1,894 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_gpio_ex.h + * @author MCD Application Team + * @brief Header file of GPIO HAL Extension module. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef STM32F1xx_HAL_GPIO_EX_H +#define STM32F1xx_HAL_GPIO_EX_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal_def.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @defgroup GPIOEx GPIOEx + * @{ + */ +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/** @defgroup GPIOEx_Exported_Constants GPIOEx Exported Constants + * @{ + */ + +/** @defgroup GPIOEx_EVENTOUT EVENTOUT Cortex Configuration + * @brief This section propose definition to use the Cortex EVENTOUT signal. + * @{ + */ + +/** @defgroup GPIOEx_EVENTOUT_PIN EVENTOUT Pin + * @{ + */ + +#define AFIO_EVENTOUT_PIN_0 AFIO_EVCR_PIN_PX0 /*!< EVENTOUT on pin 0 */ +#define AFIO_EVENTOUT_PIN_1 AFIO_EVCR_PIN_PX1 /*!< EVENTOUT on pin 1 */ +#define AFIO_EVENTOUT_PIN_2 AFIO_EVCR_PIN_PX2 /*!< EVENTOUT on pin 2 */ +#define AFIO_EVENTOUT_PIN_3 AFIO_EVCR_PIN_PX3 /*!< EVENTOUT on pin 3 */ +#define AFIO_EVENTOUT_PIN_4 AFIO_EVCR_PIN_PX4 /*!< EVENTOUT on pin 4 */ +#define AFIO_EVENTOUT_PIN_5 AFIO_EVCR_PIN_PX5 /*!< EVENTOUT on pin 5 */ +#define AFIO_EVENTOUT_PIN_6 AFIO_EVCR_PIN_PX6 /*!< EVENTOUT on pin 6 */ +#define AFIO_EVENTOUT_PIN_7 AFIO_EVCR_PIN_PX7 /*!< EVENTOUT on pin 7 */ +#define AFIO_EVENTOUT_PIN_8 AFIO_EVCR_PIN_PX8 /*!< EVENTOUT on pin 8 */ +#define AFIO_EVENTOUT_PIN_9 AFIO_EVCR_PIN_PX9 /*!< EVENTOUT on pin 9 */ +#define AFIO_EVENTOUT_PIN_10 AFIO_EVCR_PIN_PX10 /*!< EVENTOUT on pin 10 */ +#define AFIO_EVENTOUT_PIN_11 AFIO_EVCR_PIN_PX11 /*!< EVENTOUT on pin 11 */ +#define AFIO_EVENTOUT_PIN_12 AFIO_EVCR_PIN_PX12 /*!< EVENTOUT on pin 12 */ +#define AFIO_EVENTOUT_PIN_13 AFIO_EVCR_PIN_PX13 /*!< EVENTOUT on pin 13 */ +#define AFIO_EVENTOUT_PIN_14 AFIO_EVCR_PIN_PX14 /*!< EVENTOUT on pin 14 */ +#define AFIO_EVENTOUT_PIN_15 AFIO_EVCR_PIN_PX15 /*!< EVENTOUT on pin 15 */ + +#define IS_AFIO_EVENTOUT_PIN(__PIN__) (((__PIN__) == AFIO_EVENTOUT_PIN_0) || \ + ((__PIN__) == AFIO_EVENTOUT_PIN_1) || \ + ((__PIN__) == AFIO_EVENTOUT_PIN_2) || \ + ((__PIN__) == AFIO_EVENTOUT_PIN_3) || \ + ((__PIN__) == AFIO_EVENTOUT_PIN_4) || \ + ((__PIN__) == AFIO_EVENTOUT_PIN_5) || \ + ((__PIN__) == AFIO_EVENTOUT_PIN_6) || \ + ((__PIN__) == AFIO_EVENTOUT_PIN_7) || \ + ((__PIN__) == AFIO_EVENTOUT_PIN_8) || \ + ((__PIN__) == AFIO_EVENTOUT_PIN_9) || \ + ((__PIN__) == AFIO_EVENTOUT_PIN_10) || \ + ((__PIN__) == AFIO_EVENTOUT_PIN_11) || \ + ((__PIN__) == AFIO_EVENTOUT_PIN_12) || \ + ((__PIN__) == AFIO_EVENTOUT_PIN_13) || \ + ((__PIN__) == AFIO_EVENTOUT_PIN_14) || \ + ((__PIN__) == AFIO_EVENTOUT_PIN_15)) +/** + * @} + */ + +/** @defgroup GPIOEx_EVENTOUT_PORT EVENTOUT Port + * @{ + */ + +#define AFIO_EVENTOUT_PORT_A AFIO_EVCR_PORT_PA /*!< EVENTOUT on port A */ +#define AFIO_EVENTOUT_PORT_B AFIO_EVCR_PORT_PB /*!< EVENTOUT on port B */ +#define AFIO_EVENTOUT_PORT_C AFIO_EVCR_PORT_PC /*!< EVENTOUT on port C */ +#define AFIO_EVENTOUT_PORT_D AFIO_EVCR_PORT_PD /*!< EVENTOUT on port D */ +#define AFIO_EVENTOUT_PORT_E AFIO_EVCR_PORT_PE /*!< EVENTOUT on port E */ + +#define IS_AFIO_EVENTOUT_PORT(__PORT__) (((__PORT__) == AFIO_EVENTOUT_PORT_A) || \ + ((__PORT__) == AFIO_EVENTOUT_PORT_B) || \ + ((__PORT__) == AFIO_EVENTOUT_PORT_C) || \ + ((__PORT__) == AFIO_EVENTOUT_PORT_D) || \ + ((__PORT__) == AFIO_EVENTOUT_PORT_E)) +/** + * @} + */ + +/** + * @} + */ + +/** @defgroup GPIOEx_AFIO_AF_REMAPPING Alternate Function Remapping + * @brief This section propose definition to remap the alternate function to some other port/pins. + * @{ + */ + +/** + * @brief Enable the remapping of SPI1 alternate function NSS, SCK, MISO and MOSI. + * @note ENABLE: Remap (NSS/PA15, SCK/PB3, MISO/PB4, MOSI/PB5) + * @retval None + */ +#define __HAL_AFIO_REMAP_SPI1_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_SPI1_REMAP) + +/** + * @brief Disable the remapping of SPI1 alternate function NSS, SCK, MISO and MOSI. + * @note DISABLE: No remap (NSS/PA4, SCK/PA5, MISO/PA6, MOSI/PA7) + * @retval None + */ +#define __HAL_AFIO_REMAP_SPI1_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_SPI1_REMAP) + +/** + * @brief Enable the remapping of I2C1 alternate function SCL and SDA. + * @note ENABLE: Remap (SCL/PB8, SDA/PB9) + * @retval None + */ +#define __HAL_AFIO_REMAP_I2C1_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_I2C1_REMAP) + +/** + * @brief Disable the remapping of I2C1 alternate function SCL and SDA. + * @note DISABLE: No remap (SCL/PB6, SDA/PB7) + * @retval None + */ +#define __HAL_AFIO_REMAP_I2C1_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_I2C1_REMAP) + +/** + * @brief Enable the remapping of USART1 alternate function TX and RX. + * @note ENABLE: Remap (TX/PB6, RX/PB7) + * @retval None + */ +#define __HAL_AFIO_REMAP_USART1_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_USART1_REMAP) + +/** + * @brief Disable the remapping of USART1 alternate function TX and RX. + * @note DISABLE: No remap (TX/PA9, RX/PA10) + * @retval None + */ +#define __HAL_AFIO_REMAP_USART1_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_USART1_REMAP) + +/** + * @brief Enable the remapping of USART2 alternate function CTS, RTS, CK, TX and RX. + * @note ENABLE: Remap (CTS/PD3, RTS/PD4, TX/PD5, RX/PD6, CK/PD7) + * @retval None + */ +#define __HAL_AFIO_REMAP_USART2_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_USART2_REMAP) + +/** + * @brief Disable the remapping of USART2 alternate function CTS, RTS, CK, TX and RX. + * @note DISABLE: No remap (CTS/PA0, RTS/PA1, TX/PA2, RX/PA3, CK/PA4) + * @retval None + */ +#define __HAL_AFIO_REMAP_USART2_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_USART2_REMAP) + +/** + * @brief Enable the remapping of USART3 alternate function CTS, RTS, CK, TX and RX. + * @note ENABLE: Full remap (TX/PD8, RX/PD9, CK/PD10, CTS/PD11, RTS/PD12) + * @retval None + */ +#define __HAL_AFIO_REMAP_USART3_ENABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_USART3_REMAP_FULLREMAP, AFIO_MAPR_USART3_REMAP_FULLREMAP) + +/** + * @brief Enable the remapping of USART3 alternate function CTS, RTS, CK, TX and RX. + * @note PARTIAL: Partial remap (TX/PC10, RX/PC11, CK/PC12, CTS/PB13, RTS/PB14) + * @retval None + */ +#define __HAL_AFIO_REMAP_USART3_PARTIAL() AFIO_REMAP_PARTIAL(AFIO_MAPR_USART3_REMAP_PARTIALREMAP, AFIO_MAPR_USART3_REMAP_FULLREMAP) + +/** + * @brief Disable the remapping of USART3 alternate function CTS, RTS, CK, TX and RX. + * @note DISABLE: No remap (TX/PB10, RX/PB11, CK/PB12, CTS/PB13, RTS/PB14) + * @retval None + */ +#define __HAL_AFIO_REMAP_USART3_DISABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_USART3_REMAP_NOREMAP, AFIO_MAPR_USART3_REMAP_FULLREMAP) + +/** + * @brief Enable the remapping of TIM1 alternate function channels 1 to 4, 1N to 3N, external trigger (ETR) and Break input (BKIN) + * @note ENABLE: Full remap (ETR/PE7, CH1/PE9, CH2/PE11, CH3/PE13, CH4/PE14, BKIN/PE15, CH1N/PE8, CH2N/PE10, CH3N/PE12) + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM1_ENABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM1_REMAP_FULLREMAP, AFIO_MAPR_TIM1_REMAP_FULLREMAP) + +/** + * @brief Enable the remapping of TIM1 alternate function channels 1 to 4, 1N to 3N, external trigger (ETR) and Break input (BKIN) + * @note PARTIAL: Partial remap (ETR/PA12, CH1/PA8, CH2/PA9, CH3/PA10, CH4/PA11, BKIN/PA6, CH1N/PA7, CH2N/PB0, CH3N/PB1) + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM1_PARTIAL() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM1_REMAP_PARTIALREMAP, AFIO_MAPR_TIM1_REMAP_FULLREMAP) + +/** + * @brief Disable the remapping of TIM1 alternate function channels 1 to 4, 1N to 3N, external trigger (ETR) and Break input (BKIN) + * @note DISABLE: No remap (ETR/PA12, CH1/PA8, CH2/PA9, CH3/PA10, CH4/PA11, BKIN/PB12, CH1N/PB13, CH2N/PB14, CH3N/PB15) + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM1_DISABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM1_REMAP_NOREMAP, AFIO_MAPR_TIM1_REMAP_FULLREMAP) + +/** + * @brief Enable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR) + * @note ENABLE: Full remap (CH1/ETR/PA15, CH2/PB3, CH3/PB10, CH4/PB11) + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM2_ENABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM2_REMAP_FULLREMAP, AFIO_MAPR_TIM2_REMAP_FULLREMAP) + +/** + * @brief Enable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR) + * @note PARTIAL_2: Partial remap (CH1/ETR/PA0, CH2/PA1, CH3/PB10, CH4/PB11) + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM2_PARTIAL_2() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM2_REMAP_PARTIALREMAP2, AFIO_MAPR_TIM2_REMAP_FULLREMAP) + +/** + * @brief Enable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR) + * @note PARTIAL_1: Partial remap (CH1/ETR/PA15, CH2/PB3, CH3/PA2, CH4/PA3) + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM2_PARTIAL_1() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM2_REMAP_PARTIALREMAP1, AFIO_MAPR_TIM2_REMAP_FULLREMAP) + +/** + * @brief Disable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR) + * @note DISABLE: No remap (CH1/ETR/PA0, CH2/PA1, CH3/PA2, CH4/PA3) + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM2_DISABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM2_REMAP_NOREMAP, AFIO_MAPR_TIM2_REMAP_FULLREMAP) + +/** + * @brief Enable the remapping of TIM3 alternate function channels 1 to 4 + * @note ENABLE: Full remap (CH1/PC6, CH2/PC7, CH3/PC8, CH4/PC9) + * @note TIM3_ETR on PE0 is not re-mapped. + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM3_ENABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM3_REMAP_FULLREMAP, AFIO_MAPR_TIM3_REMAP_FULLREMAP) + +/** + * @brief Enable the remapping of TIM3 alternate function channels 1 to 4 + * @note PARTIAL: Partial remap (CH1/PB4, CH2/PB5, CH3/PB0, CH4/PB1) + * @note TIM3_ETR on PE0 is not re-mapped. + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM3_PARTIAL() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM3_REMAP_PARTIALREMAP, AFIO_MAPR_TIM3_REMAP_FULLREMAP) + +/** + * @brief Disable the remapping of TIM3 alternate function channels 1 to 4 + * @note DISABLE: No remap (CH1/PA6, CH2/PA7, CH3/PB0, CH4/PB1) + * @note TIM3_ETR on PE0 is not re-mapped. + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM3_DISABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM3_REMAP_NOREMAP, AFIO_MAPR_TIM3_REMAP_FULLREMAP) + +/** + * @brief Enable the remapping of TIM4 alternate function channels 1 to 4. + * @note ENABLE: Full remap (TIM4_CH1/PD12, TIM4_CH2/PD13, TIM4_CH3/PD14, TIM4_CH4/PD15) + * @note TIM4_ETR on PE0 is not re-mapped. + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM4_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_TIM4_REMAP) + +/** + * @brief Disable the remapping of TIM4 alternate function channels 1 to 4. + * @note DISABLE: No remap (TIM4_CH1/PB6, TIM4_CH2/PB7, TIM4_CH3/PB8, TIM4_CH4/PB9) + * @note TIM4_ETR on PE0 is not re-mapped. + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM4_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_TIM4_REMAP) + +#if defined(AFIO_MAPR_CAN_REMAP_REMAP1) + +/** + * @brief Enable or disable the remapping of CAN alternate function CAN_RX and CAN_TX in devices with a single CAN interface. + * @note CASE 1: CAN_RX mapped to PA11, CAN_TX mapped to PA12 + * @retval None + */ +#define __HAL_AFIO_REMAP_CAN1_1() AFIO_REMAP_PARTIAL(AFIO_MAPR_CAN_REMAP_REMAP1, AFIO_MAPR_CAN_REMAP) + +/** + * @brief Enable or disable the remapping of CAN alternate function CAN_RX and CAN_TX in devices with a single CAN interface. + * @note CASE 2: CAN_RX mapped to PB8, CAN_TX mapped to PB9 (not available on 36-pin package) + * @retval None + */ +#define __HAL_AFIO_REMAP_CAN1_2() AFIO_REMAP_PARTIAL(AFIO_MAPR_CAN_REMAP_REMAP2, AFIO_MAPR_CAN_REMAP) + +/** + * @brief Enable or disable the remapping of CAN alternate function CAN_RX and CAN_TX in devices with a single CAN interface. + * @note CASE 3: CAN_RX mapped to PD0, CAN_TX mapped to PD1 + * @retval None + */ +#define __HAL_AFIO_REMAP_CAN1_3() AFIO_REMAP_PARTIAL(AFIO_MAPR_CAN_REMAP_REMAP3, AFIO_MAPR_CAN_REMAP) + +#endif + +/** + * @brief Enable the remapping of PD0 and PD1. When the HSE oscillator is not used + * (application running on internal 8 MHz RC) PD0 and PD1 can be mapped on OSC_IN and + * OSC_OUT. This is available only on 36, 48 and 64 pins packages (PD0 and PD1 are available + * on 100-pin and 144-pin packages, no need for remapping). + * @note ENABLE: PD0 remapped on OSC_IN, PD1 remapped on OSC_OUT. + * @retval None + */ +#define __HAL_AFIO_REMAP_PD01_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_PD01_REMAP) + +/** + * @brief Disable the remapping of PD0 and PD1. When the HSE oscillator is not used + * (application running on internal 8 MHz RC) PD0 and PD1 can be mapped on OSC_IN and + * OSC_OUT. This is available only on 36, 48 and 64 pins packages (PD0 and PD1 are available + * on 100-pin and 144-pin packages, no need for remapping). + * @note DISABLE: No remapping of PD0 and PD1 + * @retval None + */ +#define __HAL_AFIO_REMAP_PD01_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_PD01_REMAP) + +#if defined(AFIO_MAPR_TIM5CH4_IREMAP) +/** + * @brief Enable the remapping of TIM5CH4. + * @note ENABLE: LSI internal clock is connected to TIM5_CH4 input for calibration purpose. + * @note This function is available only in high density value line devices. + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM5CH4_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_TIM5CH4_IREMAP) + +/** + * @brief Disable the remapping of TIM5CH4. + * @note DISABLE: TIM5_CH4 is connected to PA3 + * @note This function is available only in high density value line devices. + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM5CH4_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_TIM5CH4_IREMAP) +#endif + +#if defined(AFIO_MAPR_ETH_REMAP) +/** + * @brief Enable the remapping of Ethernet MAC connections with the PHY. + * @note ENABLE: Remap (RX_DV-CRS_DV/PD8, RXD0/PD9, RXD1/PD10, RXD2/PD11, RXD3/PD12) + * @note This bit is available only in connectivity line devices and is reserved otherwise. + * @retval None + */ +#define __HAL_AFIO_REMAP_ETH_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_ETH_REMAP) + +/** + * @brief Disable the remapping of Ethernet MAC connections with the PHY. + * @note DISABLE: No remap (RX_DV-CRS_DV/PA7, RXD0/PC4, RXD1/PC5, RXD2/PB0, RXD3/PB1) + * @note This bit is available only in connectivity line devices and is reserved otherwise. + * @retval None + */ +#define __HAL_AFIO_REMAP_ETH_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_ETH_REMAP) +#endif + +#if defined(AFIO_MAPR_CAN2_REMAP) + +/** + * @brief Enable the remapping of CAN2 alternate function CAN2_RX and CAN2_TX. + * @note ENABLE: Remap (CAN2_RX/PB5, CAN2_TX/PB6) + * @note This bit is available only in connectivity line devices and is reserved otherwise. + * @retval None + */ +#define __HAL_AFIO_REMAP_CAN2_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_CAN2_REMAP) + +/** + * @brief Disable the remapping of CAN2 alternate function CAN2_RX and CAN2_TX. + * @note DISABLE: No remap (CAN2_RX/PB12, CAN2_TX/PB13) + * @note This bit is available only in connectivity line devices and is reserved otherwise. + * @retval None + */ +#define __HAL_AFIO_REMAP_CAN2_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_CAN2_REMAP) +#endif + +#if defined(AFIO_MAPR_MII_RMII_SEL) +/** + * @brief Configures the Ethernet MAC internally for use with an external MII or RMII PHY. + * @note ETH_RMII: Configure Ethernet MAC for connection with an RMII PHY + * @note This bit is available only in connectivity line devices and is reserved otherwise. + * @retval None + */ +#define __HAL_AFIO_ETH_RMII() AFIO_REMAP_ENABLE(AFIO_MAPR_MII_RMII_SEL) + +/** + * @brief Configures the Ethernet MAC internally for use with an external MII or RMII PHY. + * @note ETH_MII: Configure Ethernet MAC for connection with an MII PHY + * @note This bit is available only in connectivity line devices and is reserved otherwise. + * @retval None + */ +#define __HAL_AFIO_ETH_MII() AFIO_REMAP_DISABLE(AFIO_MAPR_MII_RMII_SEL) +#endif + +/** + * @brief Enable the remapping of ADC1_ETRGINJ (ADC 1 External trigger injected conversion). + * @note ENABLE: ADC1 External Event injected conversion is connected to TIM8 Channel4. + * @retval None + */ +#define __HAL_AFIO_REMAP_ADC1_ETRGINJ_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_ADC1_ETRGINJ_REMAP) + +/** + * @brief Disable the remapping of ADC1_ETRGINJ (ADC 1 External trigger injected conversion). + * @note DISABLE: ADC1 External trigger injected conversion is connected to EXTI15 + * @retval None + */ +#define __HAL_AFIO_REMAP_ADC1_ETRGINJ_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_ADC1_ETRGINJ_REMAP) + +/** + * @brief Enable the remapping of ADC1_ETRGREG (ADC 1 External trigger regular conversion). + * @note ENABLE: ADC1 External Event regular conversion is connected to TIM8 TRG0. + * @retval None + */ +#define __HAL_AFIO_REMAP_ADC1_ETRGREG_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_ADC1_ETRGREG_REMAP) + +/** + * @brief Disable the remapping of ADC1_ETRGREG (ADC 1 External trigger regular conversion). + * @note DISABLE: ADC1 External trigger regular conversion is connected to EXTI11 + * @retval None + */ +#define __HAL_AFIO_REMAP_ADC1_ETRGREG_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_ADC1_ETRGREG_REMAP) + +#if defined(AFIO_MAPR_ADC2_ETRGINJ_REMAP) + +/** + * @brief Enable the remapping of ADC2_ETRGREG (ADC 2 External trigger injected conversion). + * @note ENABLE: ADC2 External Event injected conversion is connected to TIM8 Channel4. + * @retval None + */ +#define __HAL_AFIO_REMAP_ADC2_ETRGINJ_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_ADC2_ETRGINJ_REMAP) + +/** + * @brief Disable the remapping of ADC2_ETRGREG (ADC 2 External trigger injected conversion). + * @note DISABLE: ADC2 External trigger injected conversion is connected to EXTI15 + * @retval None + */ +#define __HAL_AFIO_REMAP_ADC2_ETRGINJ_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_ADC2_ETRGINJ_REMAP) +#endif + +#if defined (AFIO_MAPR_ADC2_ETRGREG_REMAP) + +/** + * @brief Enable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion). + * @note ENABLE: ADC2 External Event regular conversion is connected to TIM8 TRG0. + * @retval None + */ +#define __HAL_AFIO_REMAP_ADC2_ETRGREG_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_ADC2_ETRGREG_REMAP) + +/** + * @brief Disable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion). + * @note DISABLE: ADC2 External trigger regular conversion is connected to EXTI11 + * @retval None + */ +#define __HAL_AFIO_REMAP_ADC2_ETRGREG_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_ADC2_ETRGREG_REMAP) +#endif + +/** + * @brief Enable the Serial wire JTAG configuration + * @note ENABLE: Full SWJ (JTAG-DP + SW-DP): Reset State + * @retval None + */ +#define __HAL_AFIO_REMAP_SWJ_ENABLE() AFIO_DBGAFR_CONFIG(AFIO_MAPR_SWJ_CFG_RESET) + +/** + * @brief Enable the Serial wire JTAG configuration + * @note NONJTRST: Full SWJ (JTAG-DP + SW-DP) but without NJTRST + * @retval None + */ +#define __HAL_AFIO_REMAP_SWJ_NONJTRST() AFIO_DBGAFR_CONFIG(AFIO_MAPR_SWJ_CFG_NOJNTRST) + +/** + * @brief Enable the Serial wire JTAG configuration + * @note NOJTAG: JTAG-DP Disabled and SW-DP Enabled + * @retval None + */ + +#define __HAL_AFIO_REMAP_SWJ_NOJTAG() AFIO_DBGAFR_CONFIG(AFIO_MAPR_SWJ_CFG_JTAGDISABLE) + +/** + * @brief Disable the Serial wire JTAG configuration + * @note DISABLE: JTAG-DP Disabled and SW-DP Disabled + * @retval None + */ +#define __HAL_AFIO_REMAP_SWJ_DISABLE() AFIO_DBGAFR_CONFIG(AFIO_MAPR_SWJ_CFG_DISABLE) + +#if defined(AFIO_MAPR_SPI3_REMAP) + +/** + * @brief Enable the remapping of SPI3 alternate functions SPI3_NSS/I2S3_WS, SPI3_SCK/I2S3_CK, SPI3_MISO, SPI3_MOSI/I2S3_SD. + * @note ENABLE: Remap (SPI3_NSS-I2S3_WS/PA4, SPI3_SCK-I2S3_CK/PC10, SPI3_MISO/PC11, SPI3_MOSI-I2S3_SD/PC12) + * @note This bit is available only in connectivity line devices and is reserved otherwise. + * @retval None + */ +#define __HAL_AFIO_REMAP_SPI3_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_SPI3_REMAP) + +/** + * @brief Disable the remapping of SPI3 alternate functions SPI3_NSS/I2S3_WS, SPI3_SCK/I2S3_CK, SPI3_MISO, SPI3_MOSI/I2S3_SD. + * @note DISABLE: No remap (SPI3_NSS-I2S3_WS/PA15, SPI3_SCK-I2S3_CK/PB3, SPI3_MISO/PB4, SPI3_MOSI-I2S3_SD/PB5). + * @note This bit is available only in connectivity line devices and is reserved otherwise. + * @retval None + */ +#define __HAL_AFIO_REMAP_SPI3_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_SPI3_REMAP) +#endif + +#if defined(AFIO_MAPR_TIM2ITR1_IREMAP) + +/** + * @brief Control of TIM2_ITR1 internal mapping. + * @note TO_USB: Connect USB OTG SOF (Start of Frame) output to TIM2_ITR1 for calibration purposes. + * @note This bit is available only in connectivity line devices and is reserved otherwise. + * @retval None + */ +#define __HAL_AFIO_TIM2ITR1_TO_USB() AFIO_REMAP_ENABLE(AFIO_MAPR_TIM2ITR1_IREMAP) + +/** + * @brief Control of TIM2_ITR1 internal mapping. + * @note TO_ETH: Connect TIM2_ITR1 internally to the Ethernet PTP output for calibration purposes. + * @note This bit is available only in connectivity line devices and is reserved otherwise. + * @retval None + */ +#define __HAL_AFIO_TIM2ITR1_TO_ETH() AFIO_REMAP_DISABLE(AFIO_MAPR_TIM2ITR1_IREMAP) +#endif + +#if defined(AFIO_MAPR_PTP_PPS_REMAP) + +/** + * @brief Enable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion). + * @note ENABLE: PTP_PPS is output on PB5 pin. + * @note This bit is available only in connectivity line devices and is reserved otherwise. + * @retval None + */ +#define __HAL_AFIO_ETH_PTP_PPS_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_PTP_PPS_REMAP) + +/** + * @brief Disable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion). + * @note DISABLE: PTP_PPS not output on PB5 pin. + * @note This bit is available only in connectivity line devices and is reserved otherwise. + * @retval None + */ +#define __HAL_AFIO_ETH_PTP_PPS_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_PTP_PPS_REMAP) +#endif + +#if defined(AFIO_MAPR2_TIM9_REMAP) + +/** + * @brief Enable the remapping of TIM9_CH1 and TIM9_CH2. + * @note ENABLE: Remap (TIM9_CH1 on PE5 and TIM9_CH2 on PE6). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM9_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM9_REMAP) + +/** + * @brief Disable the remapping of TIM9_CH1 and TIM9_CH2. + * @note DISABLE: No remap (TIM9_CH1 on PA2 and TIM9_CH2 on PA3). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM9_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM9_REMAP) +#endif + +#if defined(AFIO_MAPR2_TIM10_REMAP) + +/** + * @brief Enable the remapping of TIM10_CH1. + * @note ENABLE: Remap (TIM10_CH1 on PF6). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM10_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM10_REMAP) + +/** + * @brief Disable the remapping of TIM10_CH1. + * @note DISABLE: No remap (TIM10_CH1 on PB8). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM10_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM10_REMAP) +#endif + +#if defined(AFIO_MAPR2_TIM11_REMAP) +/** + * @brief Enable the remapping of TIM11_CH1. + * @note ENABLE: Remap (TIM11_CH1 on PF7). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM11_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM11_REMAP) + +/** + * @brief Disable the remapping of TIM11_CH1. + * @note DISABLE: No remap (TIM11_CH1 on PB9). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM11_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM11_REMAP) +#endif + +#if defined(AFIO_MAPR2_TIM13_REMAP) + +/** + * @brief Enable the remapping of TIM13_CH1. + * @note ENABLE: Remap STM32F100:(TIM13_CH1 on PF8). Others:(TIM13_CH1 on PB0). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM13_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM13_REMAP) + +/** + * @brief Disable the remapping of TIM13_CH1. + * @note DISABLE: No remap STM32F100:(TIM13_CH1 on PA6). Others:(TIM13_CH1 on PC8). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM13_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM13_REMAP) +#endif + +#if defined(AFIO_MAPR2_TIM14_REMAP) + +/** + * @brief Enable the remapping of TIM14_CH1. + * @note ENABLE: Remap STM32F100:(TIM14_CH1 on PB1). Others:(TIM14_CH1 on PF9). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM14_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM14_REMAP) + +/** + * @brief Disable the remapping of TIM14_CH1. + * @note DISABLE: No remap STM32F100:(TIM14_CH1 on PC9). Others:(TIM14_CH1 on PA7). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM14_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM14_REMAP) +#endif + +#if defined(AFIO_MAPR2_FSMC_NADV_REMAP) + +/** + * @brief Controls the use of the optional FSMC_NADV signal. + * @note DISCONNECTED: The NADV signal is not connected. The I/O pin can be used by another peripheral. + * @retval None + */ +#define __HAL_AFIO_FSMCNADV_DISCONNECTED() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_FSMC_NADV_REMAP) + +/** + * @brief Controls the use of the optional FSMC_NADV signal. + * @note CONNECTED: The NADV signal is connected to the output (default). + * @retval None + */ +#define __HAL_AFIO_FSMCNADV_CONNECTED() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_FSMC_NADV_REMAP) +#endif + +#if defined(AFIO_MAPR2_TIM15_REMAP) + +/** + * @brief Enable the remapping of TIM15_CH1 and TIM15_CH2. + * @note ENABLE: Remap (TIM15_CH1 on PB14 and TIM15_CH2 on PB15). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM15_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM15_REMAP) + +/** + * @brief Disable the remapping of TIM15_CH1 and TIM15_CH2. + * @note DISABLE: No remap (TIM15_CH1 on PA2 and TIM15_CH2 on PA3). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM15_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM15_REMAP) +#endif + +#if defined(AFIO_MAPR2_TIM16_REMAP) + +/** + * @brief Enable the remapping of TIM16_CH1. + * @note ENABLE: Remap (TIM16_CH1 on PA6). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM16_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM16_REMAP) + +/** + * @brief Disable the remapping of TIM16_CH1. + * @note DISABLE: No remap (TIM16_CH1 on PB8). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM16_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM16_REMAP) +#endif + +#if defined(AFIO_MAPR2_TIM17_REMAP) + +/** + * @brief Enable the remapping of TIM17_CH1. + * @note ENABLE: Remap (TIM17_CH1 on PA7). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM17_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM17_REMAP) + +/** + * @brief Disable the remapping of TIM17_CH1. + * @note DISABLE: No remap (TIM17_CH1 on PB9). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM17_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM17_REMAP) +#endif + +#if defined(AFIO_MAPR2_CEC_REMAP) + +/** + * @brief Enable the remapping of CEC. + * @note ENABLE: Remap (CEC on PB10). + * @retval None + */ +#define __HAL_AFIO_REMAP_CEC_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_CEC_REMAP) + +/** + * @brief Disable the remapping of CEC. + * @note DISABLE: No remap (CEC on PB8). + * @retval None + */ +#define __HAL_AFIO_REMAP_CEC_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_CEC_REMAP) +#endif + +#if defined(AFIO_MAPR2_TIM1_DMA_REMAP) + +/** + * @brief Controls the mapping of the TIM1_CH1 TIM1_CH2 DMA requests onto the DMA1 channels. + * @note ENABLE: Remap (TIM1_CH1 DMA request/DMA1 Channel6, TIM1_CH2 DMA request/DMA1 Channel6) + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM1DMA_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM1_DMA_REMAP) + +/** + * @brief Controls the mapping of the TIM1_CH1 TIM1_CH2 DMA requests onto the DMA1 channels. + * @note DISABLE: No remap (TIM1_CH1 DMA request/DMA1 Channel2, TIM1_CH2 DMA request/DMA1 Channel3). + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM1DMA_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM1_DMA_REMAP) +#endif + +#if defined(AFIO_MAPR2_TIM67_DAC_DMA_REMAP) + +/** + * @brief Controls the mapping of the TIM6_DAC1 and TIM7_DAC2 DMA requests onto the DMA1 channels. + * @note ENABLE: Remap (TIM6_DAC1 DMA request/DMA1 Channel3, TIM7_DAC2 DMA request/DMA1 Channel4) + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM67DACDMA_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM67_DAC_DMA_REMAP) + +/** + * @brief Controls the mapping of the TIM6_DAC1 and TIM7_DAC2 DMA requests onto the DMA1 channels. + * @note DISABLE: No remap (TIM6_DAC1 DMA request/DMA2 Channel3, TIM7_DAC2 DMA request/DMA2 Channel4) + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM67DACDMA_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM67_DAC_DMA_REMAP) +#endif + +#if defined(AFIO_MAPR2_TIM12_REMAP) + +/** + * @brief Enable the remapping of TIM12_CH1 and TIM12_CH2. + * @note ENABLE: Remap (TIM12_CH1 on PB12 and TIM12_CH2 on PB13). + * @note This bit is available only in high density value line devices. + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM12_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM12_REMAP) + +/** + * @brief Disable the remapping of TIM12_CH1 and TIM12_CH2. + * @note DISABLE: No remap (TIM12_CH1 on PC4 and TIM12_CH2 on PC5). + * @note This bit is available only in high density value line devices. + * @retval None + */ +#define __HAL_AFIO_REMAP_TIM12_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM12_REMAP) +#endif + +#if defined(AFIO_MAPR2_MISC_REMAP) + +/** + * @brief Miscellaneous features remapping. + * This bit is set and cleared by software. It controls miscellaneous features. + * The DMA2 channel 5 interrupt position in the vector table. + * The timer selection for DAC trigger 3 (TSEL[2:0] = 011, for more details refer to the DAC_CR register). + * @note ENABLE: DMA2 channel 5 interrupt is mapped separately at position 60 and TIM15 TRGO event is + * selected as DAC Trigger 3, TIM15 triggers TIM1/3. + * @note This bit is available only in high density value line devices. + * @retval None + */ +#define __HAL_AFIO_REMAP_MISC_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_MISC_REMAP) + +/** + * @brief Miscellaneous features remapping. + * This bit is set and cleared by software. It controls miscellaneous features. + * The DMA2 channel 5 interrupt position in the vector table. + * The timer selection for DAC trigger 3 (TSEL[2:0] = 011, for more details refer to the DAC_CR register). + * @note DISABLE: DMA2 channel 5 interrupt is mapped with DMA2 channel 4 at position 59, TIM5 TRGO + * event is selected as DAC Trigger 3, TIM5 triggers TIM1/3. + * @note This bit is available only in high density value line devices. + * @retval None + */ +#define __HAL_AFIO_REMAP_MISC_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_MISC_REMAP) +#endif + +/** + * @} + */ + +/** + * @} + */ + +/** @defgroup GPIOEx_Private_Macros GPIOEx Private Macros + * @{ + */ +#if defined(STM32F101x6) || defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6) +#define GPIO_GET_INDEX(__GPIOx__) (((__GPIOx__) == (GPIOA))? 0uL :\ + ((__GPIOx__) == (GPIOB))? 1uL :\ + ((__GPIOx__) == (GPIOC))? 2uL :3uL) +#elif defined(STM32F100xB) || defined(STM32F101xB) || defined(STM32F103xB) || defined(STM32F105xC) || defined(STM32F107xC) +#define GPIO_GET_INDEX(__GPIOx__) (((__GPIOx__) == (GPIOA))? 0uL :\ + ((__GPIOx__) == (GPIOB))? 1uL :\ + ((__GPIOx__) == (GPIOC))? 2uL :\ + ((__GPIOx__) == (GPIOD))? 3uL :4uL) +#elif defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG) +#define GPIO_GET_INDEX(__GPIOx__) (((__GPIOx__) == (GPIOA))? 0uL :\ + ((__GPIOx__) == (GPIOB))? 1uL :\ + ((__GPIOx__) == (GPIOC))? 2uL :\ + ((__GPIOx__) == (GPIOD))? 3uL :\ + ((__GPIOx__) == (GPIOE))? 4uL :\ + ((__GPIOx__) == (GPIOF))? 5uL :6uL) +#endif + +#define AFIO_REMAP_ENABLE(REMAP_PIN) do{ uint32_t tmpreg = AFIO->MAPR; \ + tmpreg |= AFIO_MAPR_SWJ_CFG; \ + tmpreg |= REMAP_PIN; \ + AFIO->MAPR = tmpreg; \ + }while(0u) + +#define AFIO_REMAP_DISABLE(REMAP_PIN) do{ uint32_t tmpreg = AFIO->MAPR; \ + tmpreg |= AFIO_MAPR_SWJ_CFG; \ + tmpreg &= ~REMAP_PIN; \ + AFIO->MAPR = tmpreg; \ + }while(0u) + +#define AFIO_REMAP_PARTIAL(REMAP_PIN, REMAP_PIN_MASK) do{ uint32_t tmpreg = AFIO->MAPR; \ + tmpreg &= ~REMAP_PIN_MASK; \ + tmpreg |= AFIO_MAPR_SWJ_CFG; \ + tmpreg |= REMAP_PIN; \ + AFIO->MAPR = tmpreg; \ + }while(0u) + +#define AFIO_DBGAFR_CONFIG(DBGAFR_SWJCFG) do{ uint32_t tmpreg = AFIO->MAPR; \ + tmpreg &= ~AFIO_MAPR_SWJ_CFG_Msk; \ + tmpreg |= DBGAFR_SWJCFG; \ + AFIO->MAPR = tmpreg; \ + }while(0u) + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ +/* Exported functions --------------------------------------------------------*/ + +/** @addtogroup GPIOEx_Exported_Functions + * @{ + */ + +/** @addtogroup GPIOEx_Exported_Functions_Group1 + * @{ + */ +void HAL_GPIOEx_ConfigEventout(uint32_t GPIO_PortSource, uint32_t GPIO_PinSource); +void HAL_GPIOEx_EnableEventout(void); +void HAL_GPIOEx_DisableEventout(void); + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* STM32F1xx_HAL_GPIO_EX_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_pwr.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_pwr.h new file mode 100644 index 00000000..a1f40ac1 --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_pwr.h @@ -0,0 +1,388 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_pwr.h + * @author MCD Application Team + * @brief Header file of PWR HAL module. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F1xx_HAL_PWR_H +#define __STM32F1xx_HAL_PWR_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal_def.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @addtogroup PWR + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ + +/** @defgroup PWR_Exported_Types PWR Exported Types + * @{ + */ + +/** + * @brief PWR PVD configuration structure definition + */ +typedef struct +{ + uint32_t PVDLevel; /*!< PVDLevel: Specifies the PVD detection level. + This parameter can be a value of @ref PWR_PVD_detection_level */ + + uint32_t Mode; /*!< Mode: Specifies the operating mode for the selected pins. + This parameter can be a value of @ref PWR_PVD_Mode */ +} PWR_PVDTypeDef; + + +/** + * @} + */ + + +/* Internal constants --------------------------------------------------------*/ + +/** @addtogroup PWR_Private_Constants + * @{ + */ + +#define PWR_EXTI_LINE_PVD ((uint32_t)0x00010000) /*!< External interrupt line 16 Connected to the PVD EXTI Line */ + +/** + * @} + */ + + +/* Exported constants --------------------------------------------------------*/ + +/** @defgroup PWR_Exported_Constants PWR Exported Constants + * @{ + */ + +/** @defgroup PWR_PVD_detection_level PWR PVD detection level + * @{ + */ +#define PWR_PVDLEVEL_0 PWR_CR_PLS_2V2 +#define PWR_PVDLEVEL_1 PWR_CR_PLS_2V3 +#define PWR_PVDLEVEL_2 PWR_CR_PLS_2V4 +#define PWR_PVDLEVEL_3 PWR_CR_PLS_2V5 +#define PWR_PVDLEVEL_4 PWR_CR_PLS_2V6 +#define PWR_PVDLEVEL_5 PWR_CR_PLS_2V7 +#define PWR_PVDLEVEL_6 PWR_CR_PLS_2V8 +#define PWR_PVDLEVEL_7 PWR_CR_PLS_2V9 + +/** + * @} + */ + +/** @defgroup PWR_PVD_Mode PWR PVD Mode + * @{ + */ +#define PWR_PVD_MODE_NORMAL 0x00000000U /*!< basic mode is used */ +#define PWR_PVD_MODE_IT_RISING 0x00010001U /*!< External Interrupt Mode with Rising edge trigger detection */ +#define PWR_PVD_MODE_IT_FALLING 0x00010002U /*!< External Interrupt Mode with Falling edge trigger detection */ +#define PWR_PVD_MODE_IT_RISING_FALLING 0x00010003U /*!< External Interrupt Mode with Rising/Falling edge trigger detection */ +#define PWR_PVD_MODE_EVENT_RISING 0x00020001U /*!< Event Mode with Rising edge trigger detection */ +#define PWR_PVD_MODE_EVENT_FALLING 0x00020002U /*!< Event Mode with Falling edge trigger detection */ +#define PWR_PVD_MODE_EVENT_RISING_FALLING 0x00020003U /*!< Event Mode with Rising/Falling edge trigger detection */ + +/** + * @} + */ + + +/** @defgroup PWR_WakeUp_Pins PWR WakeUp Pins + * @{ + */ + +#define PWR_WAKEUP_PIN1 PWR_CSR_EWUP + +/** + * @} + */ + +/** @defgroup PWR_Regulator_state_in_SLEEP_STOP_mode PWR Regulator state in SLEEP/STOP mode + * @{ + */ +#define PWR_MAINREGULATOR_ON 0x00000000U +#define PWR_LOWPOWERREGULATOR_ON PWR_CR_LPDS + +/** + * @} + */ + +/** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry + * @{ + */ +#define PWR_SLEEPENTRY_WFI ((uint8_t)0x01) +#define PWR_SLEEPENTRY_WFE ((uint8_t)0x02) + +/** + * @} + */ + +/** @defgroup PWR_STOP_mode_entry PWR STOP mode entry + * @{ + */ +#define PWR_STOPENTRY_WFI ((uint8_t)0x01) +#define PWR_STOPENTRY_WFE ((uint8_t)0x02) + +/** + * @} + */ + +/** @defgroup PWR_Flag PWR Flag + * @{ + */ +#define PWR_FLAG_WU PWR_CSR_WUF +#define PWR_FLAG_SB PWR_CSR_SBF +#define PWR_FLAG_PVDO PWR_CSR_PVDO + + +/** + * @} + */ + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup PWR_Exported_Macros PWR Exported Macros + * @{ + */ + +/** @brief Check PWR flag is set or not. + * @param __FLAG__: specifies the flag to check. + * This parameter can be one of the following values: + * @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event + * was received from the WKUP pin or from the RTC alarm + * An additional wakeup event is detected if the WKUP pin is enabled + * (by setting the EWUP bit) when the WKUP pin level is already high. + * @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was + * resumed from StandBy mode. + * @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled + * by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode + * For this reason, this bit is equal to 0 after Standby or reset + * until the PVDE bit is set. + * @retval The new state of __FLAG__ (TRUE or FALSE). + */ +#define __HAL_PWR_GET_FLAG(__FLAG__) ((PWR->CSR & (__FLAG__)) == (__FLAG__)) + +/** @brief Clear the PWR's pending flags. + * @param __FLAG__: specifies the flag to clear. + * This parameter can be one of the following values: + * @arg PWR_FLAG_WU: Wake Up flag + * @arg PWR_FLAG_SB: StandBy flag + */ +#define __HAL_PWR_CLEAR_FLAG(__FLAG__) SET_BIT(PWR->CR, ((__FLAG__) << 2)) + +/** + * @brief Enable interrupt on PVD Exti Line 16. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_ENABLE_IT() SET_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD) + +/** + * @brief Disable interrupt on PVD Exti Line 16. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_DISABLE_IT() CLEAR_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD) + +/** + * @brief Enable event on PVD Exti Line 16. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_ENABLE_EVENT() SET_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD) + +/** + * @brief Disable event on PVD Exti Line 16. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_DISABLE_EVENT() CLEAR_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD) + + +/** + * @brief PVD EXTI line configuration: set falling edge trigger. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE() SET_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD) + + +/** + * @brief Disable the PVD Extended Interrupt Falling Trigger. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE() CLEAR_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD) + + +/** + * @brief PVD EXTI line configuration: set rising edge trigger. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE() SET_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD) + +/** + * @brief Disable the PVD Extended Interrupt Rising Trigger. + * This parameter can be: + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE() CLEAR_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD) + +/** + * @brief PVD EXTI line configuration: set rising & falling edge trigger. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_FALLING_EDGE() __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE(); + +/** + * @brief Disable the PVD Extended Interrupt Rising & Falling Trigger. + * This parameter can be: + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_FALLING_EDGE() __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE(); + + + +/** + * @brief Check whether the specified PVD EXTI interrupt flag is set or not. + * @retval EXTI PVD Line Status. + */ +#define __HAL_PWR_PVD_EXTI_GET_FLAG() (EXTI->PR & (PWR_EXTI_LINE_PVD)) + +/** + * @brief Clear the PVD EXTI flag. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_CLEAR_FLAG() (EXTI->PR = (PWR_EXTI_LINE_PVD)) + +/** + * @brief Generate a Software interrupt on selected EXTI line. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT() SET_BIT(EXTI->SWIER, PWR_EXTI_LINE_PVD) +/** + * @} + */ + +/* Private macro -------------------------------------------------------------*/ +/** @defgroup PWR_Private_Macros PWR Private Macros + * @{ + */ +#define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \ + ((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \ + ((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \ + ((LEVEL) == PWR_PVDLEVEL_6) || ((LEVEL) == PWR_PVDLEVEL_7)) + + +#define IS_PWR_PVD_MODE(MODE) (((MODE) == PWR_PVD_MODE_IT_RISING)|| ((MODE) == PWR_PVD_MODE_IT_FALLING) || \ + ((MODE) == PWR_PVD_MODE_IT_RISING_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING) || \ + ((MODE) == PWR_PVD_MODE_EVENT_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING_FALLING) || \ + ((MODE) == PWR_PVD_MODE_NORMAL)) + +#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1)) + +#define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \ + ((REGULATOR) == PWR_LOWPOWERREGULATOR_ON)) + +#define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || ((ENTRY) == PWR_SLEEPENTRY_WFE)) + +#define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || ((ENTRY) == PWR_STOPENTRY_WFE)) + +/** + * @} + */ + + + +/* Exported functions --------------------------------------------------------*/ + +/** @addtogroup PWR_Exported_Functions PWR Exported Functions + * @{ + */ + +/** @addtogroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions + * @{ + */ + +/* Initialization and de-initialization functions *******************************/ +void HAL_PWR_DeInit(void); +void HAL_PWR_EnableBkUpAccess(void); +void HAL_PWR_DisableBkUpAccess(void); + +/** + * @} + */ + +/** @addtogroup PWR_Exported_Functions_Group2 Peripheral Control functions + * @{ + */ + +/* Peripheral Control functions ************************************************/ +void HAL_PWR_ConfigPVD(PWR_PVDTypeDef* sConfigPVD); +/* #define HAL_PWR_ConfigPVD 12*/ +void HAL_PWR_EnablePVD(void); +void HAL_PWR_DisablePVD(void); + +/* WakeUp pins configuration functions ****************************************/ +void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx); +void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx); + +/* Low Power modes configuration functions ************************************/ +void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry); +void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry); +void HAL_PWR_EnterSTANDBYMode(void); + +void HAL_PWR_EnableSleepOnExit(void); +void HAL_PWR_DisableSleepOnExit(void); +void HAL_PWR_EnableSEVOnPend(void); +void HAL_PWR_DisableSEVOnPend(void); + + + +void HAL_PWR_PVD_IRQHandler(void); +void HAL_PWR_PVDCallback(void); +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + + +#endif /* __STM32F1xx_HAL_PWR_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_rcc.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_rcc.h new file mode 100644 index 00000000..810a300f --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_rcc.h @@ -0,0 +1,1378 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_rcc.h + * @author MCD Application Team + * @brief Header file of RCC HAL module. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F1xx_HAL_RCC_H +#define __STM32F1xx_HAL_RCC_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal_def.h" + + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @addtogroup RCC + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ + +/** @defgroup RCC_Exported_Types RCC Exported Types + * @{ + */ + +/** + * @brief RCC PLL configuration structure definition + */ +typedef struct +{ + uint32_t PLLState; /*!< PLLState: The new state of the PLL. + This parameter can be a value of @ref RCC_PLL_Config */ + + uint32_t PLLSource; /*!< PLLSource: PLL entry clock source. + This parameter must be a value of @ref RCC_PLL_Clock_Source */ + + uint32_t PLLMUL; /*!< PLLMUL: Multiplication factor for PLL VCO input clock + This parameter must be a value of @ref RCCEx_PLL_Multiplication_Factor */ +} RCC_PLLInitTypeDef; + +/** + * @brief RCC System, AHB and APB busses clock configuration structure definition + */ +typedef struct +{ + uint32_t ClockType; /*!< The clock to be configured. + This parameter can be a value of @ref RCC_System_Clock_Type */ + + uint32_t SYSCLKSource; /*!< The clock source (SYSCLKS) used as system clock. + This parameter can be a value of @ref RCC_System_Clock_Source */ + + uint32_t AHBCLKDivider; /*!< The AHB clock (HCLK) divider. This clock is derived from the system clock (SYSCLK). + This parameter can be a value of @ref RCC_AHB_Clock_Source */ + + uint32_t APB1CLKDivider; /*!< The APB1 clock (PCLK1) divider. This clock is derived from the AHB clock (HCLK). + This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */ + + uint32_t APB2CLKDivider; /*!< The APB2 clock (PCLK2) divider. This clock is derived from the AHB clock (HCLK). + This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */ +} RCC_ClkInitTypeDef; + +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup RCC_Exported_Constants RCC Exported Constants + * @{ + */ + +/** @defgroup RCC_PLL_Clock_Source PLL Clock Source + * @{ + */ + +#define RCC_PLLSOURCE_HSI_DIV2 0x00000000U /*!< HSI clock divided by 2 selected as PLL entry clock source */ +#define RCC_PLLSOURCE_HSE RCC_CFGR_PLLSRC /*!< HSE clock selected as PLL entry clock source */ + +/** + * @} + */ + +/** @defgroup RCC_Oscillator_Type Oscillator Type + * @{ + */ +#define RCC_OSCILLATORTYPE_NONE 0x00000000U +#define RCC_OSCILLATORTYPE_HSE 0x00000001U +#define RCC_OSCILLATORTYPE_HSI 0x00000002U +#define RCC_OSCILLATORTYPE_LSE 0x00000004U +#define RCC_OSCILLATORTYPE_LSI 0x00000008U +/** + * @} + */ + +/** @defgroup RCC_HSE_Config HSE Config + * @{ + */ +#define RCC_HSE_OFF 0x00000000U /*!< HSE clock deactivation */ +#define RCC_HSE_ON RCC_CR_HSEON /*!< HSE clock activation */ +#define RCC_HSE_BYPASS ((uint32_t)(RCC_CR_HSEBYP | RCC_CR_HSEON)) /*!< External clock source for HSE clock */ +/** + * @} + */ + +/** @defgroup RCC_LSE_Config LSE Config + * @{ + */ +#define RCC_LSE_OFF 0x00000000U /*!< LSE clock deactivation */ +#define RCC_LSE_ON RCC_BDCR_LSEON /*!< LSE clock activation */ +#define RCC_LSE_BYPASS ((uint32_t)(RCC_BDCR_LSEBYP | RCC_BDCR_LSEON)) /*!< External clock source for LSE clock */ + +/** + * @} + */ + +/** @defgroup RCC_HSI_Config HSI Config + * @{ + */ +#define RCC_HSI_OFF 0x00000000U /*!< HSI clock deactivation */ +#define RCC_HSI_ON RCC_CR_HSION /*!< HSI clock activation */ + +#define RCC_HSICALIBRATION_DEFAULT 0x10U /* Default HSI calibration trimming value */ + +/** + * @} + */ + +/** @defgroup RCC_LSI_Config LSI Config + * @{ + */ +#define RCC_LSI_OFF 0x00000000U /*!< LSI clock deactivation */ +#define RCC_LSI_ON RCC_CSR_LSION /*!< LSI clock activation */ + +/** + * @} + */ + +/** @defgroup RCC_PLL_Config PLL Config + * @{ + */ +#define RCC_PLL_NONE 0x00000000U /*!< PLL is not configured */ +#define RCC_PLL_OFF 0x00000001U /*!< PLL deactivation */ +#define RCC_PLL_ON 0x00000002U /*!< PLL activation */ + +/** + * @} + */ + +/** @defgroup RCC_System_Clock_Type System Clock Type + * @{ + */ +#define RCC_CLOCKTYPE_SYSCLK 0x00000001U /*!< SYSCLK to configure */ +#define RCC_CLOCKTYPE_HCLK 0x00000002U /*!< HCLK to configure */ +#define RCC_CLOCKTYPE_PCLK1 0x00000004U /*!< PCLK1 to configure */ +#define RCC_CLOCKTYPE_PCLK2 0x00000008U /*!< PCLK2 to configure */ + +/** + * @} + */ + +/** @defgroup RCC_System_Clock_Source System Clock Source + * @{ + */ +#define RCC_SYSCLKSOURCE_HSI RCC_CFGR_SW_HSI /*!< HSI selected as system clock */ +#define RCC_SYSCLKSOURCE_HSE RCC_CFGR_SW_HSE /*!< HSE selected as system clock */ +#define RCC_SYSCLKSOURCE_PLLCLK RCC_CFGR_SW_PLL /*!< PLL selected as system clock */ + +/** + * @} + */ + +/** @defgroup RCC_System_Clock_Source_Status System Clock Source Status + * @{ + */ +#define RCC_SYSCLKSOURCE_STATUS_HSI RCC_CFGR_SWS_HSI /*!< HSI used as system clock */ +#define RCC_SYSCLKSOURCE_STATUS_HSE RCC_CFGR_SWS_HSE /*!< HSE used as system clock */ +#define RCC_SYSCLKSOURCE_STATUS_PLLCLK RCC_CFGR_SWS_PLL /*!< PLL used as system clock */ + +/** + * @} + */ + +/** @defgroup RCC_AHB_Clock_Source AHB Clock Source + * @{ + */ +#define RCC_SYSCLK_DIV1 RCC_CFGR_HPRE_DIV1 /*!< SYSCLK not divided */ +#define RCC_SYSCLK_DIV2 RCC_CFGR_HPRE_DIV2 /*!< SYSCLK divided by 2 */ +#define RCC_SYSCLK_DIV4 RCC_CFGR_HPRE_DIV4 /*!< SYSCLK divided by 4 */ +#define RCC_SYSCLK_DIV8 RCC_CFGR_HPRE_DIV8 /*!< SYSCLK divided by 8 */ +#define RCC_SYSCLK_DIV16 RCC_CFGR_HPRE_DIV16 /*!< SYSCLK divided by 16 */ +#define RCC_SYSCLK_DIV64 RCC_CFGR_HPRE_DIV64 /*!< SYSCLK divided by 64 */ +#define RCC_SYSCLK_DIV128 RCC_CFGR_HPRE_DIV128 /*!< SYSCLK divided by 128 */ +#define RCC_SYSCLK_DIV256 RCC_CFGR_HPRE_DIV256 /*!< SYSCLK divided by 256 */ +#define RCC_SYSCLK_DIV512 RCC_CFGR_HPRE_DIV512 /*!< SYSCLK divided by 512 */ + +/** + * @} + */ + +/** @defgroup RCC_APB1_APB2_Clock_Source APB1 APB2 Clock Source + * @{ + */ +#define RCC_HCLK_DIV1 RCC_CFGR_PPRE1_DIV1 /*!< HCLK not divided */ +#define RCC_HCLK_DIV2 RCC_CFGR_PPRE1_DIV2 /*!< HCLK divided by 2 */ +#define RCC_HCLK_DIV4 RCC_CFGR_PPRE1_DIV4 /*!< HCLK divided by 4 */ +#define RCC_HCLK_DIV8 RCC_CFGR_PPRE1_DIV8 /*!< HCLK divided by 8 */ +#define RCC_HCLK_DIV16 RCC_CFGR_PPRE1_DIV16 /*!< HCLK divided by 16 */ + +/** + * @} + */ + +/** @defgroup RCC_RTC_Clock_Source RTC Clock Source + * @{ + */ +#define RCC_RTCCLKSOURCE_NO_CLK 0x00000000U /*!< No clock */ +#define RCC_RTCCLKSOURCE_LSE RCC_BDCR_RTCSEL_LSE /*!< LSE oscillator clock used as RTC clock */ +#define RCC_RTCCLKSOURCE_LSI RCC_BDCR_RTCSEL_LSI /*!< LSI oscillator clock used as RTC clock */ +#define RCC_RTCCLKSOURCE_HSE_DIV128 RCC_BDCR_RTCSEL_HSE /*!< HSE oscillator clock divided by 128 used as RTC clock */ +/** + * @} + */ + + +/** @defgroup RCC_MCO_Index MCO Index + * @{ + */ +#define RCC_MCO1 0x00000000U +#define RCC_MCO RCC_MCO1 /*!< MCO1 to be compliant with other families with 2 MCOs*/ + +/** + * @} + */ + +/** @defgroup RCC_MCOx_Clock_Prescaler MCO Clock Prescaler + * @{ + */ +#define RCC_MCODIV_1 0x00000000U + +/** + * @} + */ + +/** @defgroup RCC_Interrupt Interrupts + * @{ + */ +#define RCC_IT_LSIRDY ((uint8_t)RCC_CIR_LSIRDYF) /*!< LSI Ready Interrupt flag */ +#define RCC_IT_LSERDY ((uint8_t)RCC_CIR_LSERDYF) /*!< LSE Ready Interrupt flag */ +#define RCC_IT_HSIRDY ((uint8_t)RCC_CIR_HSIRDYF) /*!< HSI Ready Interrupt flag */ +#define RCC_IT_HSERDY ((uint8_t)RCC_CIR_HSERDYF) /*!< HSE Ready Interrupt flag */ +#define RCC_IT_PLLRDY ((uint8_t)RCC_CIR_PLLRDYF) /*!< PLL Ready Interrupt flag */ +#define RCC_IT_CSS ((uint8_t)RCC_CIR_CSSF) /*!< Clock Security System Interrupt flag */ +/** + * @} + */ + +/** @defgroup RCC_Flag Flags + * Elements values convention: XXXYYYYYb + * - YYYYY : Flag position in the register + * - XXX : Register index + * - 001: CR register + * - 010: BDCR register + * - 011: CSR register + * @{ + */ +/* Flags in the CR register */ +#define RCC_FLAG_HSIRDY ((uint8_t)((CR_REG_INDEX << 5U) | RCC_CR_HSIRDY_Pos)) /*!< Internal High Speed clock ready flag */ +#define RCC_FLAG_HSERDY ((uint8_t)((CR_REG_INDEX << 5U) | RCC_CR_HSERDY_Pos)) /*!< External High Speed clock ready flag */ +#define RCC_FLAG_PLLRDY ((uint8_t)((CR_REG_INDEX << 5U) | RCC_CR_PLLRDY_Pos)) /*!< PLL clock ready flag */ + +/* Flags in the CSR register */ +#define RCC_FLAG_LSIRDY ((uint8_t)((CSR_REG_INDEX << 5U) | RCC_CSR_LSIRDY_Pos)) /*!< Internal Low Speed oscillator Ready */ +#define RCC_FLAG_PINRST ((uint8_t)((CSR_REG_INDEX << 5U) | RCC_CSR_PINRSTF_Pos)) /*!< PIN reset flag */ +#define RCC_FLAG_PORRST ((uint8_t)((CSR_REG_INDEX << 5U) | RCC_CSR_PORRSTF_Pos)) /*!< POR/PDR reset flag */ +#define RCC_FLAG_SFTRST ((uint8_t)((CSR_REG_INDEX << 5U) | RCC_CSR_SFTRSTF_Pos)) /*!< Software Reset flag */ +#define RCC_FLAG_IWDGRST ((uint8_t)((CSR_REG_INDEX << 5U) | RCC_CSR_IWDGRSTF_Pos)) /*!< Independent Watchdog reset flag */ +#define RCC_FLAG_WWDGRST ((uint8_t)((CSR_REG_INDEX << 5U) | RCC_CSR_WWDGRSTF_Pos)) /*!< Window watchdog reset flag */ +#define RCC_FLAG_LPWRRST ((uint8_t)((CSR_REG_INDEX << 5U) | RCC_CSR_LPWRRSTF_Pos)) /*!< Low-Power reset flag */ + +/* Flags in the BDCR register */ +#define RCC_FLAG_LSERDY ((uint8_t)((BDCR_REG_INDEX << 5U) | RCC_BDCR_LSERDY_Pos)) /*!< External Low Speed oscillator Ready */ + +/** + * @} + */ + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ + +/** @defgroup RCC_Exported_Macros RCC Exported Macros + * @{ + */ + +/** @defgroup RCC_Peripheral_Clock_Enable_Disable Peripheral Clock Enable Disable + * @brief Enable or disable the AHB1 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ +#define __HAL_RCC_DMA1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHBENR, RCC_AHBENR_DMA1EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_DMA1EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_SRAM_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHBENR, RCC_AHBENR_SRAMEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_SRAMEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_FLITF_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHBENR, RCC_AHBENR_FLITFEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_FLITFEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_CRC_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHBENR, RCC_AHBENR_CRCEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_CRCEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_DMA1_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_DMA1EN)) +#define __HAL_RCC_SRAM_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_SRAMEN)) +#define __HAL_RCC_FLITF_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_FLITFEN)) +#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_CRCEN)) + +/** + * @} + */ + +/** @defgroup RCC_AHB_Peripheral_Clock_Enable_Disable_Status AHB Peripheral Clock Enable Disable Status + * @brief Get the enable or disable status of the AHB peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ + +#define __HAL_RCC_DMA1_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_DMA1EN)) != RESET) +#define __HAL_RCC_DMA1_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_DMA1EN)) == RESET) +#define __HAL_RCC_SRAM_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_SRAMEN)) != RESET) +#define __HAL_RCC_SRAM_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_SRAMEN)) == RESET) +#define __HAL_RCC_FLITF_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_FLITFEN)) != RESET) +#define __HAL_RCC_FLITF_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_FLITFEN)) == RESET) +#define __HAL_RCC_CRC_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_CRCEN)) != RESET) +#define __HAL_RCC_CRC_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_CRCEN)) == RESET) + +/** + * @} + */ + +/** @defgroup RCC_APB1_Clock_Enable_Disable APB1 Clock Enable Disable + * @brief Enable or disable the Low Speed APB (APB1) peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ +#define __HAL_RCC_TIM2_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM3_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_WWDG_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_USART2_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_USART2EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_USART2EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_I2C1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C1EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C1EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_BKP_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_BKPEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_BKPEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_PWR_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN)) +#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN)) +#define __HAL_RCC_WWDG_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_WWDGEN)) +#define __HAL_RCC_USART2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_USART2EN)) +#define __HAL_RCC_I2C1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C1EN)) + +#define __HAL_RCC_BKP_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_BKPEN)) +#define __HAL_RCC_PWR_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_PWREN)) + +/** + * @} + */ + +/** @defgroup RCC_APB1_Peripheral_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status + * @brief Get the enable or disable status of the APB1 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ + +#define __HAL_RCC_TIM2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) != RESET) +#define __HAL_RCC_TIM2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) == RESET) +#define __HAL_RCC_TIM3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) != RESET) +#define __HAL_RCC_TIM3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) == RESET) +#define __HAL_RCC_WWDG_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_WWDGEN)) != RESET) +#define __HAL_RCC_WWDG_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_WWDGEN)) == RESET) +#define __HAL_RCC_USART2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART2EN)) != RESET) +#define __HAL_RCC_USART2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART2EN)) == RESET) +#define __HAL_RCC_I2C1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C1EN)) != RESET) +#define __HAL_RCC_I2C1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C1EN)) == RESET) +#define __HAL_RCC_BKP_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_BKPEN)) != RESET) +#define __HAL_RCC_BKP_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_BKPEN)) == RESET) +#define __HAL_RCC_PWR_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_PWREN)) != RESET) +#define __HAL_RCC_PWR_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_PWREN)) == RESET) + +/** + * @} + */ + +/** @defgroup RCC_APB2_Clock_Enable_Disable APB2 Clock Enable Disable + * @brief Enable or disable the High Speed APB (APB2) peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ +#define __HAL_RCC_AFIO_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_AFIOEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_AFIOEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_GPIOA_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPAEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPAEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_GPIOB_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPBEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPBEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_GPIOC_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPCEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPCEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPDEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPDEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_ADC1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC1EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC1EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_SPI1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_USART1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_AFIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_AFIOEN)) +#define __HAL_RCC_GPIOA_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPAEN)) +#define __HAL_RCC_GPIOB_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPBEN)) +#define __HAL_RCC_GPIOC_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPCEN)) +#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPDEN)) +#define __HAL_RCC_ADC1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC1EN)) + +#define __HAL_RCC_TIM1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM1EN)) +#define __HAL_RCC_SPI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI1EN)) +#define __HAL_RCC_USART1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_USART1EN)) + +/** + * @} + */ + +/** @defgroup RCC_APB2_Peripheral_Clock_Enable_Disable_Status APB2 Peripheral Clock Enable Disable Status + * @brief Get the enable or disable status of the APB2 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ + +#define __HAL_RCC_AFIO_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_AFIOEN)) != RESET) +#define __HAL_RCC_AFIO_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_AFIOEN)) == RESET) +#define __HAL_RCC_GPIOA_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPAEN)) != RESET) +#define __HAL_RCC_GPIOA_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPAEN)) == RESET) +#define __HAL_RCC_GPIOB_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPBEN)) != RESET) +#define __HAL_RCC_GPIOB_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPBEN)) == RESET) +#define __HAL_RCC_GPIOC_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPCEN)) != RESET) +#define __HAL_RCC_GPIOC_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPCEN)) == RESET) +#define __HAL_RCC_GPIOD_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPDEN)) != RESET) +#define __HAL_RCC_GPIOD_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPDEN)) == RESET) +#define __HAL_RCC_ADC1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC1EN)) != RESET) +#define __HAL_RCC_ADC1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC1EN)) == RESET) +#define __HAL_RCC_TIM1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM1EN)) != RESET) +#define __HAL_RCC_TIM1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM1EN)) == RESET) +#define __HAL_RCC_SPI1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI1EN)) != RESET) +#define __HAL_RCC_SPI1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI1EN)) == RESET) +#define __HAL_RCC_USART1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART1EN)) != RESET) +#define __HAL_RCC_USART1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART1EN)) == RESET) + +/** + * @} + */ + +/** @defgroup RCC_APB1_Force_Release_Reset APB1 Force Release Reset + * @brief Force or release APB1 peripheral reset. + * @{ + */ +#define __HAL_RCC_APB1_FORCE_RESET() (RCC->APB2RSTR = 0xFFFFFFFFU) +#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST)) +#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST)) +#define __HAL_RCC_WWDG_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_WWDGRST)) +#define __HAL_RCC_USART2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USART2RST)) +#define __HAL_RCC_I2C1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C1RST)) + +#define __HAL_RCC_BKP_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_BKPRST)) +#define __HAL_RCC_PWR_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_PWRRST)) + +#define __HAL_RCC_APB1_RELEASE_RESET() (RCC->APB1RSTR = 0x00) +#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST)) +#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST)) +#define __HAL_RCC_WWDG_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_WWDGRST)) +#define __HAL_RCC_USART2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_USART2RST)) +#define __HAL_RCC_I2C1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C1RST)) + +#define __HAL_RCC_BKP_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_BKPRST)) +#define __HAL_RCC_PWR_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_PWRRST)) + +/** + * @} + */ + +/** @defgroup RCC_APB2_Force_Release_Reset APB2 Force Release Reset + * @brief Force or release APB2 peripheral reset. + * @{ + */ +#define __HAL_RCC_APB2_FORCE_RESET() (RCC->APB2RSTR = 0xFFFFFFFFU) +#define __HAL_RCC_AFIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_AFIORST)) +#define __HAL_RCC_GPIOA_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPARST)) +#define __HAL_RCC_GPIOB_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPBRST)) +#define __HAL_RCC_GPIOC_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPCRST)) +#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPDRST)) +#define __HAL_RCC_ADC1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_ADC1RST)) + +#define __HAL_RCC_TIM1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM1RST)) +#define __HAL_RCC_SPI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI1RST)) +#define __HAL_RCC_USART1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_USART1RST)) + +#define __HAL_RCC_APB2_RELEASE_RESET() (RCC->APB2RSTR = 0x00) +#define __HAL_RCC_AFIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_AFIORST)) +#define __HAL_RCC_GPIOA_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPARST)) +#define __HAL_RCC_GPIOB_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPBRST)) +#define __HAL_RCC_GPIOC_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPCRST)) +#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPDRST)) +#define __HAL_RCC_ADC1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_ADC1RST)) + +#define __HAL_RCC_TIM1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM1RST)) +#define __HAL_RCC_SPI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI1RST)) +#define __HAL_RCC_USART1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_USART1RST)) + +/** + * @} + */ + +/** @defgroup RCC_HSI_Configuration HSI Configuration + * @{ + */ + +/** @brief Macros to enable or disable the Internal High Speed oscillator (HSI). + * @note The HSI is stopped by hardware when entering STOP and STANDBY modes. + * @note HSI can not be stopped if it is used as system clock source. In this case, + * you have to select another source of the system clock then stop the HSI. + * @note After enabling the HSI, the application software should wait on HSIRDY + * flag to be set indicating that HSI clock is stable and can be used as + * system clock source. + * @note When the HSI is stopped, HSIRDY flag goes low after 6 HSI oscillator + * clock cycles. + */ +#define __HAL_RCC_HSI_ENABLE() (*(__IO uint32_t *) RCC_CR_HSION_BB = ENABLE) +#define __HAL_RCC_HSI_DISABLE() (*(__IO uint32_t *) RCC_CR_HSION_BB = DISABLE) + +/** @brief Macro to adjust the Internal High Speed oscillator (HSI) calibration value. + * @note The calibration is used to compensate for the variations in voltage + * and temperature that influence the frequency of the internal HSI RC. + * @param _HSICALIBRATIONVALUE_ specifies the calibration trimming value. + * (default is RCC_HSICALIBRATION_DEFAULT). + * This parameter must be a number between 0 and 0x1F. + */ +#define __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(_HSICALIBRATIONVALUE_) \ + (MODIFY_REG(RCC->CR, RCC_CR_HSITRIM, (uint32_t)(_HSICALIBRATIONVALUE_) << RCC_CR_HSITRIM_Pos)) + +/** + * @} + */ + +/** @defgroup RCC_LSI_Configuration LSI Configuration + * @{ + */ + +/** @brief Macro to enable the Internal Low Speed oscillator (LSI). + * @note After enabling the LSI, the application software should wait on + * LSIRDY flag to be set indicating that LSI clock is stable and can + * be used to clock the IWDG and/or the RTC. + */ +#define __HAL_RCC_LSI_ENABLE() (*(__IO uint32_t *) RCC_CSR_LSION_BB = ENABLE) + +/** @brief Macro to disable the Internal Low Speed oscillator (LSI). + * @note LSI can not be disabled if the IWDG is running. + * @note When the LSI is stopped, LSIRDY flag goes low after 6 LSI oscillator + * clock cycles. + */ +#define __HAL_RCC_LSI_DISABLE() (*(__IO uint32_t *) RCC_CSR_LSION_BB = DISABLE) + +/** + * @} + */ + +/** @defgroup RCC_HSE_Configuration HSE Configuration + * @{ + */ + +/** + * @brief Macro to configure the External High Speed oscillator (HSE). + * @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not + * supported by this macro. User should request a transition to HSE Off + * first and then HSE On or HSE Bypass. + * @note After enabling the HSE (RCC_HSE_ON or RCC_HSE_Bypass), the application + * software should wait on HSERDY flag to be set indicating that HSE clock + * is stable and can be used to clock the PLL and/or system clock. + * @note HSE state can not be changed if it is used directly or through the + * PLL as system clock. In this case, you have to select another source + * of the system clock then change the HSE state (ex. disable it). + * @note The HSE is stopped by hardware when entering STOP and STANDBY modes. + * @note This function reset the CSSON bit, so if the clock security system(CSS) + * was previously enabled you have to enable it again after calling this + * function. + * @param __STATE__ specifies the new state of the HSE. + * This parameter can be one of the following values: + * @arg @ref RCC_HSE_OFF turn OFF the HSE oscillator, HSERDY flag goes low after + * 6 HSE oscillator clock cycles. + * @arg @ref RCC_HSE_ON turn ON the HSE oscillator + * @arg @ref RCC_HSE_BYPASS HSE oscillator bypassed with external clock + */ +#define __HAL_RCC_HSE_CONFIG(__STATE__) \ + do{ \ + if ((__STATE__) == RCC_HSE_ON) \ + { \ + SET_BIT(RCC->CR, RCC_CR_HSEON); \ + } \ + else if ((__STATE__) == RCC_HSE_OFF) \ + { \ + CLEAR_BIT(RCC->CR, RCC_CR_HSEON); \ + CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); \ + } \ + else if ((__STATE__) == RCC_HSE_BYPASS) \ + { \ + SET_BIT(RCC->CR, RCC_CR_HSEBYP); \ + SET_BIT(RCC->CR, RCC_CR_HSEON); \ + } \ + else \ + { \ + CLEAR_BIT(RCC->CR, RCC_CR_HSEON); \ + CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); \ + } \ + }while(0U) + +/** + * @} + */ + +/** @defgroup RCC_LSE_Configuration LSE Configuration + * @{ + */ + +/** + * @brief Macro to configure the External Low Speed oscillator (LSE). + * @note Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not supported by this macro. + * @note As the LSE is in the Backup domain and write access is denied to + * this domain after reset, you have to enable write access using + * @ref HAL_PWR_EnableBkUpAccess() function before to configure the LSE + * (to be done once after reset). + * @note After enabling the LSE (RCC_LSE_ON or RCC_LSE_BYPASS), the application + * software should wait on LSERDY flag to be set indicating that LSE clock + * is stable and can be used to clock the RTC. + * @param __STATE__ specifies the new state of the LSE. + * This parameter can be one of the following values: + * @arg @ref RCC_LSE_OFF turn OFF the LSE oscillator, LSERDY flag goes low after + * 6 LSE oscillator clock cycles. + * @arg @ref RCC_LSE_ON turn ON the LSE oscillator. + * @arg @ref RCC_LSE_BYPASS LSE oscillator bypassed with external clock. + */ +#define __HAL_RCC_LSE_CONFIG(__STATE__) \ + do{ \ + if ((__STATE__) == RCC_LSE_ON) \ + { \ + SET_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ + } \ + else if ((__STATE__) == RCC_LSE_OFF) \ + { \ + CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ + CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \ + } \ + else if ((__STATE__) == RCC_LSE_BYPASS) \ + { \ + SET_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \ + SET_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ + } \ + else \ + { \ + CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ + CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \ + } \ + }while(0U) + +/** + * @} + */ + +/** @defgroup RCC_PLL_Configuration PLL Configuration + * @{ + */ + +/** @brief Macro to enable the main PLL. + * @note After enabling the main PLL, the application software should wait on + * PLLRDY flag to be set indicating that PLL clock is stable and can + * be used as system clock source. + * @note The main PLL is disabled by hardware when entering STOP and STANDBY modes. + */ +#define __HAL_RCC_PLL_ENABLE() (*(__IO uint32_t *) RCC_CR_PLLON_BB = ENABLE) + +/** @brief Macro to disable the main PLL. + * @note The main PLL can not be disabled if it is used as system clock source + */ +#define __HAL_RCC_PLL_DISABLE() (*(__IO uint32_t *) RCC_CR_PLLON_BB = DISABLE) + +/** @brief Macro to configure the main PLL clock source and multiplication factors. + * @note This function must be used only when the main PLL is disabled. + * + * @param __RCC_PLLSOURCE__ specifies the PLL entry clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_PLLSOURCE_HSI_DIV2 HSI oscillator clock selected as PLL clock entry + * @arg @ref RCC_PLLSOURCE_HSE HSE oscillator clock selected as PLL clock entry + * @param __PLLMUL__ specifies the multiplication factor for PLL VCO output clock + * This parameter can be one of the following values: + * @arg @ref RCC_PLL_MUL4 PLLVCO = PLL clock entry x 4 + * @arg @ref RCC_PLL_MUL6 PLLVCO = PLL clock entry x 6 + @if STM32F105xC + * @arg @ref RCC_PLL_MUL6_5 PLLVCO = PLL clock entry x 6.5 + @elseif STM32F107xC + * @arg @ref RCC_PLL_MUL6_5 PLLVCO = PLL clock entry x 6.5 + @else + * @arg @ref RCC_PLL_MUL2 PLLVCO = PLL clock entry x 2 + * @arg @ref RCC_PLL_MUL3 PLLVCO = PLL clock entry x 3 + * @arg @ref RCC_PLL_MUL10 PLLVCO = PLL clock entry x 10 + * @arg @ref RCC_PLL_MUL11 PLLVCO = PLL clock entry x 11 + * @arg @ref RCC_PLL_MUL12 PLLVCO = PLL clock entry x 12 + * @arg @ref RCC_PLL_MUL13 PLLVCO = PLL clock entry x 13 + * @arg @ref RCC_PLL_MUL14 PLLVCO = PLL clock entry x 14 + * @arg @ref RCC_PLL_MUL15 PLLVCO = PLL clock entry x 15 + * @arg @ref RCC_PLL_MUL16 PLLVCO = PLL clock entry x 16 + @endif + * @arg @ref RCC_PLL_MUL8 PLLVCO = PLL clock entry x 8 + * @arg @ref RCC_PLL_MUL9 PLLVCO = PLL clock entry x 9 + * + */ +#define __HAL_RCC_PLL_CONFIG(__RCC_PLLSOURCE__, __PLLMUL__)\ + MODIFY_REG(RCC->CFGR, (RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL),((__RCC_PLLSOURCE__) | (__PLLMUL__) )) + +/** @brief Get oscillator clock selected as PLL input clock + * @retval The clock source used for PLL entry. The returned value can be one + * of the following: + * @arg @ref RCC_PLLSOURCE_HSI_DIV2 HSI oscillator clock selected as PLL input clock + * @arg @ref RCC_PLLSOURCE_HSE HSE oscillator clock selected as PLL input clock + */ +#define __HAL_RCC_GET_PLL_OSCSOURCE() ((uint32_t)(READ_BIT(RCC->CFGR, RCC_CFGR_PLLSRC))) + +/** + * @} + */ + +/** @defgroup RCC_Get_Clock_source Get Clock source + * @{ + */ + +/** + * @brief Macro to configure the system clock source. + * @param __SYSCLKSOURCE__ specifies the system clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_SYSCLKSOURCE_HSI HSI oscillator is used as system clock source. + * @arg @ref RCC_SYSCLKSOURCE_HSE HSE oscillator is used as system clock source. + * @arg @ref RCC_SYSCLKSOURCE_PLLCLK PLL output is used as system clock source. + */ +#define __HAL_RCC_SYSCLK_CONFIG(__SYSCLKSOURCE__) \ + MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, (__SYSCLKSOURCE__)) + +/** @brief Macro to get the clock source used as system clock. + * @retval The clock source used as system clock. The returned value can be one + * of the following: + * @arg @ref RCC_SYSCLKSOURCE_STATUS_HSI HSI used as system clock + * @arg @ref RCC_SYSCLKSOURCE_STATUS_HSE HSE used as system clock + * @arg @ref RCC_SYSCLKSOURCE_STATUS_PLLCLK PLL used as system clock + */ +#define __HAL_RCC_GET_SYSCLK_SOURCE() ((uint32_t)(READ_BIT(RCC->CFGR,RCC_CFGR_SWS))) + +/** + * @} + */ + +/** @defgroup RCCEx_MCOx_Clock_Config RCC Extended MCOx Clock Config + * @{ + */ + +#if defined(RCC_CFGR_MCO_3) +/** @brief Macro to configure the MCO clock. + * @param __MCOCLKSOURCE__ specifies the MCO clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_MCO1SOURCE_NOCLOCK No clock selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_SYSCLK System clock (SYSCLK) selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_HSI HSI selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_HSE HSE selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_PLLCLK PLL clock divided by 2 selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_PLL2CLK PLL2 clock selected by 2 selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_PLL3CLK_DIV2 PLL3 clock divided by 2 selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_EXT_HSE XT1 external 3-25 MHz oscillator clock selected (for Ethernet) as MCO clock + * @arg @ref RCC_MCO1SOURCE_PLL3CLK PLL3 clock selected (for Ethernet) as MCO clock + * @param __MCODIV__ specifies the MCO clock prescaler. + * This parameter can be one of the following values: + * @arg @ref RCC_MCODIV_1 No division applied on MCO clock source + */ +#else +/** @brief Macro to configure the MCO clock. + * @param __MCOCLKSOURCE__ specifies the MCO clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_MCO1SOURCE_NOCLOCK No clock selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_SYSCLK System clock (SYSCLK) selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_HSI HSI selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_HSE HSE selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_PLLCLK PLL clock divided by 2 selected as MCO clock + * @param __MCODIV__ specifies the MCO clock prescaler. + * This parameter can be one of the following values: + * @arg @ref RCC_MCODIV_1 No division applied on MCO clock source + */ +#endif + +#define __HAL_RCC_MCO1_CONFIG(__MCOCLKSOURCE__, __MCODIV__) \ + MODIFY_REG(RCC->CFGR, RCC_CFGR_MCO, (__MCOCLKSOURCE__)) + + +/** + * @} + */ + +/** @defgroup RCC_RTC_Clock_Configuration RCC RTC Clock Configuration +* @{ +*/ + +/** @brief Macro to configure the RTC clock (RTCCLK). + * @note As the RTC clock configuration bits are in the Backup domain and write + * access is denied to this domain after reset, you have to enable write + * access using the Power Backup Access macro before to configure + * the RTC clock source (to be done once after reset). + * @note Once the RTC clock is configured it can't be changed unless the + * Backup domain is reset using @ref __HAL_RCC_BACKUPRESET_FORCE() macro, or by + * a Power On Reset (POR). + * + * @param __RTC_CLKSOURCE__ specifies the RTC clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_RTCCLKSOURCE_NO_CLK No clock selected as RTC clock + * @arg @ref RCC_RTCCLKSOURCE_LSE LSE selected as RTC clock + * @arg @ref RCC_RTCCLKSOURCE_LSI LSI selected as RTC clock + * @arg @ref RCC_RTCCLKSOURCE_HSE_DIV128 HSE divided by 128 selected as RTC clock + * @note If the LSE or LSI is used as RTC clock source, the RTC continues to + * work in STOP and STANDBY modes, and can be used as wakeup source. + * However, when the HSE clock is used as RTC clock source, the RTC + * cannot be used in STOP and STANDBY modes. + * @note The maximum input clock frequency for RTC is 1MHz (when using HSE as + * RTC clock source). + */ +#define __HAL_RCC_RTC_CONFIG(__RTC_CLKSOURCE__) MODIFY_REG(RCC->BDCR, RCC_BDCR_RTCSEL, (__RTC_CLKSOURCE__)) + +/** @brief Macro to get the RTC clock source. + * @retval The clock source can be one of the following values: + * @arg @ref RCC_RTCCLKSOURCE_NO_CLK No clock selected as RTC clock + * @arg @ref RCC_RTCCLKSOURCE_LSE LSE selected as RTC clock + * @arg @ref RCC_RTCCLKSOURCE_LSI LSI selected as RTC clock + * @arg @ref RCC_RTCCLKSOURCE_HSE_DIV128 HSE divided by 128 selected as RTC clock + */ +#define __HAL_RCC_GET_RTC_SOURCE() (READ_BIT(RCC->BDCR, RCC_BDCR_RTCSEL)) + +/** @brief Macro to enable the the RTC clock. + * @note These macros must be used only after the RTC clock source was selected. + */ +#define __HAL_RCC_RTC_ENABLE() (*(__IO uint32_t *) RCC_BDCR_RTCEN_BB = ENABLE) + +/** @brief Macro to disable the the RTC clock. + * @note These macros must be used only after the RTC clock source was selected. + */ +#define __HAL_RCC_RTC_DISABLE() (*(__IO uint32_t *) RCC_BDCR_RTCEN_BB = DISABLE) + +/** @brief Macro to force the Backup domain reset. + * @note This function resets the RTC peripheral (including the backup registers) + * and the RTC clock source selection in RCC_BDCR register. + */ +#define __HAL_RCC_BACKUPRESET_FORCE() (*(__IO uint32_t *) RCC_BDCR_BDRST_BB = ENABLE) + +/** @brief Macros to release the Backup domain reset. + */ +#define __HAL_RCC_BACKUPRESET_RELEASE() (*(__IO uint32_t *) RCC_BDCR_BDRST_BB = DISABLE) + +/** + * @} + */ + +/** @defgroup RCC_Flags_Interrupts_Management Flags Interrupts Management + * @brief macros to manage the specified RCC Flags and interrupts. + * @{ + */ + +/** @brief Enable RCC interrupt. + * @param __INTERRUPT__ specifies the RCC interrupt sources to be enabled. + * This parameter can be any combination of the following values: + * @arg @ref RCC_IT_LSIRDY LSI ready interrupt + * @arg @ref RCC_IT_LSERDY LSE ready interrupt + * @arg @ref RCC_IT_HSIRDY HSI ready interrupt + * @arg @ref RCC_IT_HSERDY HSE ready interrupt + * @arg @ref RCC_IT_PLLRDY main PLL ready interrupt + @if STM32F105xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @elsif STM32F107xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @endif + */ +#define __HAL_RCC_ENABLE_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE1_ADDRESS |= (__INTERRUPT__)) + +/** @brief Disable RCC interrupt. + * @param __INTERRUPT__ specifies the RCC interrupt sources to be disabled. + * This parameter can be any combination of the following values: + * @arg @ref RCC_IT_LSIRDY LSI ready interrupt + * @arg @ref RCC_IT_LSERDY LSE ready interrupt + * @arg @ref RCC_IT_HSIRDY HSI ready interrupt + * @arg @ref RCC_IT_HSERDY HSE ready interrupt + * @arg @ref RCC_IT_PLLRDY main PLL ready interrupt + @if STM32F105xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @elsif STM32F107xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @endif + */ +#define __HAL_RCC_DISABLE_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE1_ADDRESS &= (uint8_t)(~(__INTERRUPT__))) + +/** @brief Clear the RCC's interrupt pending bits. + * @param __INTERRUPT__ specifies the interrupt pending bit to clear. + * This parameter can be any combination of the following values: + * @arg @ref RCC_IT_LSIRDY LSI ready interrupt. + * @arg @ref RCC_IT_LSERDY LSE ready interrupt. + * @arg @ref RCC_IT_HSIRDY HSI ready interrupt. + * @arg @ref RCC_IT_HSERDY HSE ready interrupt. + * @arg @ref RCC_IT_PLLRDY Main PLL ready interrupt. + @if STM32F105xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @elsif STM32F107xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @endif + * @arg @ref RCC_IT_CSS Clock Security System interrupt + */ +#define __HAL_RCC_CLEAR_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE2_ADDRESS = (__INTERRUPT__)) + +/** @brief Check the RCC's interrupt has occurred or not. + * @param __INTERRUPT__ specifies the RCC interrupt source to check. + * This parameter can be one of the following values: + * @arg @ref RCC_IT_LSIRDY LSI ready interrupt. + * @arg @ref RCC_IT_LSERDY LSE ready interrupt. + * @arg @ref RCC_IT_HSIRDY HSI ready interrupt. + * @arg @ref RCC_IT_HSERDY HSE ready interrupt. + * @arg @ref RCC_IT_PLLRDY Main PLL ready interrupt. + @if STM32F105xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @elsif STM32F107xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @endif + * @arg @ref RCC_IT_CSS Clock Security System interrupt + * @retval The new state of __INTERRUPT__ (TRUE or FALSE). + */ +#define __HAL_RCC_GET_IT(__INTERRUPT__) ((RCC->CIR & (__INTERRUPT__)) == (__INTERRUPT__)) + +/** @brief Set RMVF bit to clear the reset flags. + * The reset flags are RCC_FLAG_PINRST, RCC_FLAG_PORRST, RCC_FLAG_SFTRST, + * RCC_FLAG_IWDGRST, RCC_FLAG_WWDGRST, RCC_FLAG_LPWRRST + */ +#define __HAL_RCC_CLEAR_RESET_FLAGS() (*(__IO uint32_t *)RCC_CSR_RMVF_BB = ENABLE) + +/** @brief Check RCC flag is set or not. + * @param __FLAG__ specifies the flag to check. + * This parameter can be one of the following values: + * @arg @ref RCC_FLAG_HSIRDY HSI oscillator clock ready. + * @arg @ref RCC_FLAG_HSERDY HSE oscillator clock ready. + * @arg @ref RCC_FLAG_PLLRDY Main PLL clock ready. + @if STM32F105xx + * @arg @ref RCC_FLAG_PLL2RDY Main PLL2 clock ready. + * @arg @ref RCC_FLAG_PLLI2SRDY Main PLLI2S clock ready. + @elsif STM32F107xx + * @arg @ref RCC_FLAG_PLL2RDY Main PLL2 clock ready. + * @arg @ref RCC_FLAG_PLLI2SRDY Main PLLI2S clock ready. + @endif + * @arg @ref RCC_FLAG_LSERDY LSE oscillator clock ready. + * @arg @ref RCC_FLAG_LSIRDY LSI oscillator clock ready. + * @arg @ref RCC_FLAG_PINRST Pin reset. + * @arg @ref RCC_FLAG_PORRST POR/PDR reset. + * @arg @ref RCC_FLAG_SFTRST Software reset. + * @arg @ref RCC_FLAG_IWDGRST Independent Watchdog reset. + * @arg @ref RCC_FLAG_WWDGRST Window Watchdog reset. + * @arg @ref RCC_FLAG_LPWRRST Low Power reset. + * @retval The new state of __FLAG__ (TRUE or FALSE). + */ +#define __HAL_RCC_GET_FLAG(__FLAG__) (((((__FLAG__) >> 5U) == CR_REG_INDEX)? RCC->CR : \ + ((((__FLAG__) >> 5U) == BDCR_REG_INDEX)? RCC->BDCR : \ + RCC->CSR)) & (1U << ((__FLAG__) & RCC_FLAG_MASK))) + +/** + * @} + */ + +/** + * @} + */ + +/* Include RCC HAL Extension module */ +#include "stm32f1xx_hal_rcc_ex.h" + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup RCC_Exported_Functions + * @{ + */ + +/** @addtogroup RCC_Exported_Functions_Group1 + * @{ + */ + +/* Initialization and de-initialization functions ******************************/ +HAL_StatusTypeDef HAL_RCC_DeInit(void); +HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef* RCC_OscInitStruct); +HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef* RCC_ClkInitStruct, uint32_t FLatency); + +/** + * @} + */ + +/** @addtogroup RCC_Exported_Functions_Group2 + * @{ + */ + +/* Peripheral Control functions ************************************************/ +void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv); +void HAL_RCC_EnableCSS(void); +void HAL_RCC_DisableCSS(void); +uint32_t HAL_RCC_GetSysClockFreq(void); +uint32_t HAL_RCC_GetHCLKFreq(void); +uint32_t HAL_RCC_GetPCLK1Freq(void); +uint32_t HAL_RCC_GetPCLK2Freq(void); +void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef* RCC_OscInitStruct); +void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef* RCC_ClkInitStruct, uint32_t* pFLatency); + +/* CSS NMI IRQ handler */ +void HAL_RCC_NMI_IRQHandler(void); + +/* User Callbacks in non blocking mode (IT mode) */ +void HAL_RCC_CSSCallback(void); + +/** + * @} + */ + +/** + * @} + */ + +/** @addtogroup RCC_Private_Constants + * @{ + */ + +/** @defgroup RCC_Timeout RCC Timeout + * @{ + */ + +/* Disable Backup domain write protection state change timeout */ +#define RCC_DBP_TIMEOUT_VALUE 100U /* 100 ms */ +/* LSE state change timeout */ +#define RCC_LSE_TIMEOUT_VALUE LSE_STARTUP_TIMEOUT +#define CLOCKSWITCH_TIMEOUT_VALUE 5000 /* 5 s */ +#define HSE_TIMEOUT_VALUE HSE_STARTUP_TIMEOUT +#define HSI_TIMEOUT_VALUE 2U /* 2 ms (minimum Tick + 1) */ +#define LSI_TIMEOUT_VALUE 2U /* 2 ms (minimum Tick + 1) */ +#define PLL_TIMEOUT_VALUE 2U /* 2 ms (minimum Tick + 1) */ + +/** + * @} + */ + +/** @defgroup RCC_Register_Offset Register offsets + * @{ + */ +#define RCC_OFFSET (RCC_BASE - PERIPH_BASE) +#define RCC_CR_OFFSET 0x00U +#define RCC_CFGR_OFFSET 0x04U +#define RCC_CIR_OFFSET 0x08U +#define RCC_BDCR_OFFSET 0x20U +#define RCC_CSR_OFFSET 0x24U + +/** + * @} + */ + +/** @defgroup RCC_BitAddress_AliasRegion BitAddress AliasRegion + * @brief RCC registers bit address in the alias region + * @{ + */ +#define RCC_CR_OFFSET_BB (RCC_OFFSET + RCC_CR_OFFSET) +#define RCC_CFGR_OFFSET_BB (RCC_OFFSET + RCC_CFGR_OFFSET) +#define RCC_CIR_OFFSET_BB (RCC_OFFSET + RCC_CIR_OFFSET) +#define RCC_BDCR_OFFSET_BB (RCC_OFFSET + RCC_BDCR_OFFSET) +#define RCC_CSR_OFFSET_BB (RCC_OFFSET + RCC_CSR_OFFSET) + +/* --- CR Register ---*/ +/* Alias word address of HSION bit */ +#define RCC_HSION_BIT_NUMBER RCC_CR_HSION_Pos +#define RCC_CR_HSION_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CR_OFFSET_BB * 32U) + (RCC_HSION_BIT_NUMBER * 4U))) +/* Alias word address of HSEON bit */ +#define RCC_HSEON_BIT_NUMBER RCC_CR_HSEON_Pos +#define RCC_CR_HSEON_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CR_OFFSET_BB * 32U) + (RCC_HSEON_BIT_NUMBER * 4U))) +/* Alias word address of CSSON bit */ +#define RCC_CSSON_BIT_NUMBER RCC_CR_CSSON_Pos +#define RCC_CR_CSSON_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CR_OFFSET_BB * 32U) + (RCC_CSSON_BIT_NUMBER * 4U))) +/* Alias word address of PLLON bit */ +#define RCC_PLLON_BIT_NUMBER RCC_CR_PLLON_Pos +#define RCC_CR_PLLON_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CR_OFFSET_BB * 32U) + (RCC_PLLON_BIT_NUMBER * 4U))) + +/* --- CSR Register ---*/ +/* Alias word address of LSION bit */ +#define RCC_LSION_BIT_NUMBER RCC_CSR_LSION_Pos +#define RCC_CSR_LSION_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CSR_OFFSET_BB * 32U) + (RCC_LSION_BIT_NUMBER * 4U))) + +/* Alias word address of RMVF bit */ +#define RCC_RMVF_BIT_NUMBER RCC_CSR_RMVF_Pos +#define RCC_CSR_RMVF_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CSR_OFFSET_BB * 32U) + (RCC_RMVF_BIT_NUMBER * 4U))) + +/* --- BDCR Registers ---*/ +/* Alias word address of LSEON bit */ +#define RCC_LSEON_BIT_NUMBER RCC_BDCR_LSEON_Pos +#define RCC_BDCR_LSEON_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_BDCR_OFFSET_BB * 32U) + (RCC_LSEON_BIT_NUMBER * 4U))) + +/* Alias word address of LSEON bit */ +#define RCC_LSEBYP_BIT_NUMBER RCC_BDCR_LSEBYP_Pos +#define RCC_BDCR_LSEBYP_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_BDCR_OFFSET_BB * 32U) + (RCC_LSEBYP_BIT_NUMBER * 4U))) + +/* Alias word address of RTCEN bit */ +#define RCC_RTCEN_BIT_NUMBER RCC_BDCR_RTCEN_Pos +#define RCC_BDCR_RTCEN_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_BDCR_OFFSET_BB * 32U) + (RCC_RTCEN_BIT_NUMBER * 4U))) + +/* Alias word address of BDRST bit */ +#define RCC_BDRST_BIT_NUMBER RCC_BDCR_BDRST_Pos +#define RCC_BDCR_BDRST_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_BDCR_OFFSET_BB * 32U) + (RCC_BDRST_BIT_NUMBER * 4U))) + +/** + * @} + */ + +/* CR register byte 2 (Bits[23:16]) base address */ +#define RCC_CR_BYTE2_ADDRESS ((uint32_t)(RCC_BASE + RCC_CR_OFFSET + 0x02U)) + +/* CIR register byte 1 (Bits[15:8]) base address */ +#define RCC_CIR_BYTE1_ADDRESS ((uint32_t)(RCC_BASE + RCC_CIR_OFFSET + 0x01U)) + +/* CIR register byte 2 (Bits[23:16]) base address */ +#define RCC_CIR_BYTE2_ADDRESS ((uint32_t)(RCC_BASE + RCC_CIR_OFFSET + 0x02U)) + +/* Defines used for Flags */ +#define CR_REG_INDEX ((uint8_t)1) +#define BDCR_REG_INDEX ((uint8_t)2) +#define CSR_REG_INDEX ((uint8_t)3) + +#define RCC_FLAG_MASK ((uint8_t)0x1F) + +/** + * @} + */ + +/** @addtogroup RCC_Private_Macros + * @{ + */ +/** @defgroup RCC_Alias_For_Legacy Alias define maintained for legacy + * @{ + */ +#define __HAL_RCC_SYSCFG_CLK_DISABLE __HAL_RCC_AFIO_CLK_DISABLE +#define __HAL_RCC_SYSCFG_CLK_ENABLE __HAL_RCC_AFIO_CLK_ENABLE +#define __HAL_RCC_SYSCFG_FORCE_RESET __HAL_RCC_AFIO_FORCE_RESET +#define __HAL_RCC_SYSCFG_RELEASE_RESET __HAL_RCC_AFIO_RELEASE_RESET +/** + * @} + */ + +#define IS_RCC_PLLSOURCE(__SOURCE__) (((__SOURCE__) == RCC_PLLSOURCE_HSI_DIV2) || \ + ((__SOURCE__) == RCC_PLLSOURCE_HSE)) +#define IS_RCC_OSCILLATORTYPE(__OSCILLATOR__) (((__OSCILLATOR__) == RCC_OSCILLATORTYPE_NONE) || \ + (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) || \ + (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) || \ + (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) || \ + (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE)) +#define IS_RCC_HSE(__HSE__) (((__HSE__) == RCC_HSE_OFF) || ((__HSE__) == RCC_HSE_ON) || \ + ((__HSE__) == RCC_HSE_BYPASS)) +#define IS_RCC_LSE(__LSE__) (((__LSE__) == RCC_LSE_OFF) || ((__LSE__) == RCC_LSE_ON) || \ + ((__LSE__) == RCC_LSE_BYPASS)) +#define IS_RCC_HSI(__HSI__) (((__HSI__) == RCC_HSI_OFF) || ((__HSI__) == RCC_HSI_ON)) +#define IS_RCC_CALIBRATION_VALUE(__VALUE__) ((__VALUE__) <= 0x1FU) +#define IS_RCC_LSI(__LSI__) (((__LSI__) == RCC_LSI_OFF) || ((__LSI__) == RCC_LSI_ON)) +#define IS_RCC_PLL(__PLL__) (((__PLL__) == RCC_PLL_NONE) || ((__PLL__) == RCC_PLL_OFF) || \ + ((__PLL__) == RCC_PLL_ON)) + +#define IS_RCC_CLOCKTYPE(CLK) ((((CLK) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK) || \ + (((CLK) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK) || \ + (((CLK) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1) || \ + (((CLK) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2)) +#define IS_RCC_SYSCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_SYSCLKSOURCE_HSI) || \ + ((__SOURCE__) == RCC_SYSCLKSOURCE_HSE) || \ + ((__SOURCE__) == RCC_SYSCLKSOURCE_PLLCLK)) +#define IS_RCC_SYSCLKSOURCE_STATUS(__SOURCE__) (((__SOURCE__) == RCC_SYSCLKSOURCE_STATUS_HSI) || \ + ((__SOURCE__) == RCC_SYSCLKSOURCE_STATUS_HSE) || \ + ((__SOURCE__) == RCC_SYSCLKSOURCE_STATUS_PLLCLK)) +#define IS_RCC_HCLK(__HCLK__) (((__HCLK__) == RCC_SYSCLK_DIV1) || ((__HCLK__) == RCC_SYSCLK_DIV2) || \ + ((__HCLK__) == RCC_SYSCLK_DIV4) || ((__HCLK__) == RCC_SYSCLK_DIV8) || \ + ((__HCLK__) == RCC_SYSCLK_DIV16) || ((__HCLK__) == RCC_SYSCLK_DIV64) || \ + ((__HCLK__) == RCC_SYSCLK_DIV128) || ((__HCLK__) == RCC_SYSCLK_DIV256) || \ + ((__HCLK__) == RCC_SYSCLK_DIV512)) +#define IS_RCC_PCLK(__PCLK__) (((__PCLK__) == RCC_HCLK_DIV1) || ((__PCLK__) == RCC_HCLK_DIV2) || \ + ((__PCLK__) == RCC_HCLK_DIV4) || ((__PCLK__) == RCC_HCLK_DIV8) || \ + ((__PCLK__) == RCC_HCLK_DIV16)) +#define IS_RCC_MCO(__MCO__) ((__MCO__) == RCC_MCO) +#define IS_RCC_MCODIV(__DIV__) (((__DIV__) == RCC_MCODIV_1)) +#define IS_RCC_RTCCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_RTCCLKSOURCE_NO_CLK) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_LSE) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_LSI) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV128)) + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F1xx_HAL_RCC_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ + diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_rcc_ex.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_rcc_ex.h new file mode 100644 index 00000000..92844032 --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_rcc_ex.h @@ -0,0 +1,1908 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_rcc_ex.h + * @author MCD Application Team + * @brief Header file of RCC HAL Extension module. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F1xx_HAL_RCC_EX_H +#define __STM32F1xx_HAL_RCC_EX_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal_def.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @addtogroup RCCEx + * @{ + */ + +/** @addtogroup RCCEx_Private_Constants + * @{ + */ + +#if defined(STM32F105xC) || defined(STM32F107xC) + +/* Alias word address of PLLI2SON bit */ +#define PLLI2SON_BITNUMBER RCC_CR_PLL3ON_Pos +#define RCC_CR_PLLI2SON_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CR_OFFSET_BB * 32U) + (PLLI2SON_BITNUMBER * 4U))) +/* Alias word address of PLL2ON bit */ +#define PLL2ON_BITNUMBER RCC_CR_PLL2ON_Pos +#define RCC_CR_PLL2ON_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CR_OFFSET_BB * 32U) + (PLL2ON_BITNUMBER * 4U))) + +#define PLLI2S_TIMEOUT_VALUE 100U /* 100 ms */ +#define PLL2_TIMEOUT_VALUE 100U /* 100 ms */ + +#endif /* STM32F105xC || STM32F107xC */ + + +#define CR_REG_INDEX ((uint8_t)1) + +/** + * @} + */ + +/** @addtogroup RCCEx_Private_Macros + * @{ + */ + +#if defined(STM32F105xC) || defined(STM32F107xC) +#define IS_RCC_PREDIV1_SOURCE(__SOURCE__) (((__SOURCE__) == RCC_PREDIV1_SOURCE_HSE) || \ + ((__SOURCE__) == RCC_PREDIV1_SOURCE_PLL2)) +#endif /* STM32F105xC || STM32F107xC */ + +#if defined(STM32F105xC) || defined(STM32F107xC) || defined(STM32F100xB)\ + || defined(STM32F100xE) +#define IS_RCC_HSE_PREDIV(__DIV__) (((__DIV__) == RCC_HSE_PREDIV_DIV1) || ((__DIV__) == RCC_HSE_PREDIV_DIV2) || \ + ((__DIV__) == RCC_HSE_PREDIV_DIV3) || ((__DIV__) == RCC_HSE_PREDIV_DIV4) || \ + ((__DIV__) == RCC_HSE_PREDIV_DIV5) || ((__DIV__) == RCC_HSE_PREDIV_DIV6) || \ + ((__DIV__) == RCC_HSE_PREDIV_DIV7) || ((__DIV__) == RCC_HSE_PREDIV_DIV8) || \ + ((__DIV__) == RCC_HSE_PREDIV_DIV9) || ((__DIV__) == RCC_HSE_PREDIV_DIV10) || \ + ((__DIV__) == RCC_HSE_PREDIV_DIV11) || ((__DIV__) == RCC_HSE_PREDIV_DIV12) || \ + ((__DIV__) == RCC_HSE_PREDIV_DIV13) || ((__DIV__) == RCC_HSE_PREDIV_DIV14) || \ + ((__DIV__) == RCC_HSE_PREDIV_DIV15) || ((__DIV__) == RCC_HSE_PREDIV_DIV16)) + +#else +#define IS_RCC_HSE_PREDIV(__DIV__) (((__DIV__) == RCC_HSE_PREDIV_DIV1) || ((__DIV__) == RCC_HSE_PREDIV_DIV2)) +#endif /* STM32F105xC || STM32F107xC || STM32F100xB || STM32F100xE */ + +#if defined(STM32F105xC) || defined(STM32F107xC) +#define IS_RCC_PLL_MUL(__MUL__) (((__MUL__) == RCC_PLL_MUL4) || ((__MUL__) == RCC_PLL_MUL5) || \ + ((__MUL__) == RCC_PLL_MUL6) || ((__MUL__) == RCC_PLL_MUL7) || \ + ((__MUL__) == RCC_PLL_MUL8) || ((__MUL__) == RCC_PLL_MUL9) || \ + ((__MUL__) == RCC_PLL_MUL6_5)) + +#define IS_RCC_MCO1SOURCE(__SOURCE__) (((__SOURCE__) == RCC_MCO1SOURCE_SYSCLK) || ((__SOURCE__) == RCC_MCO1SOURCE_HSI) \ + || ((__SOURCE__) == RCC_MCO1SOURCE_HSE) || ((__SOURCE__) == RCC_MCO1SOURCE_PLLCLK) \ + || ((__SOURCE__) == RCC_MCO1SOURCE_PLL2CLK) || ((__SOURCE__) == RCC_MCO1SOURCE_PLL3CLK) \ + || ((__SOURCE__) == RCC_MCO1SOURCE_PLL3CLK_DIV2) || ((__SOURCE__) == RCC_MCO1SOURCE_EXT_HSE) \ + || ((__SOURCE__) == RCC_MCO1SOURCE_NOCLOCK)) + +#else +#define IS_RCC_PLL_MUL(__MUL__) (((__MUL__) == RCC_PLL_MUL2) || ((__MUL__) == RCC_PLL_MUL3) || \ + ((__MUL__) == RCC_PLL_MUL4) || ((__MUL__) == RCC_PLL_MUL5) || \ + ((__MUL__) == RCC_PLL_MUL6) || ((__MUL__) == RCC_PLL_MUL7) || \ + ((__MUL__) == RCC_PLL_MUL8) || ((__MUL__) == RCC_PLL_MUL9) || \ + ((__MUL__) == RCC_PLL_MUL10) || ((__MUL__) == RCC_PLL_MUL11) || \ + ((__MUL__) == RCC_PLL_MUL12) || ((__MUL__) == RCC_PLL_MUL13) || \ + ((__MUL__) == RCC_PLL_MUL14) || ((__MUL__) == RCC_PLL_MUL15) || \ + ((__MUL__) == RCC_PLL_MUL16)) + +#define IS_RCC_MCO1SOURCE(__SOURCE__) (((__SOURCE__) == RCC_MCO1SOURCE_SYSCLK) || ((__SOURCE__) == RCC_MCO1SOURCE_HSI) \ + || ((__SOURCE__) == RCC_MCO1SOURCE_HSE) || ((__SOURCE__) == RCC_MCO1SOURCE_PLLCLK) \ + || ((__SOURCE__) == RCC_MCO1SOURCE_NOCLOCK)) + +#endif /* STM32F105xC || STM32F107xC*/ + +#define IS_RCC_ADCPLLCLK_DIV(__ADCCLK__) (((__ADCCLK__) == RCC_ADCPCLK2_DIV2) || ((__ADCCLK__) == RCC_ADCPCLK2_DIV4) || \ + ((__ADCCLK__) == RCC_ADCPCLK2_DIV6) || ((__ADCCLK__) == RCC_ADCPCLK2_DIV8)) + +#if defined(STM32F105xC) || defined(STM32F107xC) +#define IS_RCC_I2S2CLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_I2S2CLKSOURCE_SYSCLK) || ((__SOURCE__) == RCC_I2S2CLKSOURCE_PLLI2S_VCO)) + +#define IS_RCC_I2S3CLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_I2S3CLKSOURCE_SYSCLK) || ((__SOURCE__) == RCC_I2S3CLKSOURCE_PLLI2S_VCO)) + +#define IS_RCC_USBPLLCLK_DIV(__USBCLK__) (((__USBCLK__) == RCC_USBCLKSOURCE_PLL_DIV2) || ((__USBCLK__) == RCC_USBCLKSOURCE_PLL_DIV3)) + +#define IS_RCC_PLLI2S_MUL(__MUL__) (((__MUL__) == RCC_PLLI2S_MUL8) || ((__MUL__) == RCC_PLLI2S_MUL9) || \ + ((__MUL__) == RCC_PLLI2S_MUL10) || ((__MUL__) == RCC_PLLI2S_MUL11) || \ + ((__MUL__) == RCC_PLLI2S_MUL12) || ((__MUL__) == RCC_PLLI2S_MUL13) || \ + ((__MUL__) == RCC_PLLI2S_MUL14) || ((__MUL__) == RCC_PLLI2S_MUL16) || \ + ((__MUL__) == RCC_PLLI2S_MUL20)) + +#define IS_RCC_HSE_PREDIV2(__DIV__) (((__DIV__) == RCC_HSE_PREDIV2_DIV1) || ((__DIV__) == RCC_HSE_PREDIV2_DIV2) || \ + ((__DIV__) == RCC_HSE_PREDIV2_DIV3) || ((__DIV__) == RCC_HSE_PREDIV2_DIV4) || \ + ((__DIV__) == RCC_HSE_PREDIV2_DIV5) || ((__DIV__) == RCC_HSE_PREDIV2_DIV6) || \ + ((__DIV__) == RCC_HSE_PREDIV2_DIV7) || ((__DIV__) == RCC_HSE_PREDIV2_DIV8) || \ + ((__DIV__) == RCC_HSE_PREDIV2_DIV9) || ((__DIV__) == RCC_HSE_PREDIV2_DIV10) || \ + ((__DIV__) == RCC_HSE_PREDIV2_DIV11) || ((__DIV__) == RCC_HSE_PREDIV2_DIV12) || \ + ((__DIV__) == RCC_HSE_PREDIV2_DIV13) || ((__DIV__) == RCC_HSE_PREDIV2_DIV14) || \ + ((__DIV__) == RCC_HSE_PREDIV2_DIV15) || ((__DIV__) == RCC_HSE_PREDIV2_DIV16)) + +#define IS_RCC_PLL2(__PLL__) (((__PLL__) == RCC_PLL2_NONE) || ((__PLL__) == RCC_PLL2_OFF) || \ + ((__PLL__) == RCC_PLL2_ON)) + +#define IS_RCC_PLL2_MUL(__MUL__) (((__MUL__) == RCC_PLL2_MUL8) || ((__MUL__) == RCC_PLL2_MUL9) || \ + ((__MUL__) == RCC_PLL2_MUL10) || ((__MUL__) == RCC_PLL2_MUL11) || \ + ((__MUL__) == RCC_PLL2_MUL12) || ((__MUL__) == RCC_PLL2_MUL13) || \ + ((__MUL__) == RCC_PLL2_MUL14) || ((__MUL__) == RCC_PLL2_MUL16) || \ + ((__MUL__) == RCC_PLL2_MUL20)) + +#define IS_RCC_PERIPHCLOCK(__SELECTION__) \ + ((((__SELECTION__) & RCC_PERIPHCLK_RTC) == RCC_PERIPHCLK_RTC) || \ + (((__SELECTION__) & RCC_PERIPHCLK_ADC) == RCC_PERIPHCLK_ADC) || \ + (((__SELECTION__) & RCC_PERIPHCLK_I2S2) == RCC_PERIPHCLK_I2S2) || \ + (((__SELECTION__) & RCC_PERIPHCLK_I2S3) == RCC_PERIPHCLK_I2S3) || \ + (((__SELECTION__) & RCC_PERIPHCLK_USB) == RCC_PERIPHCLK_USB)) + +#elif defined(STM32F103xE) || defined(STM32F103xG) + +#define IS_RCC_I2S2CLKSOURCE(__SOURCE__) ((__SOURCE__) == RCC_I2S2CLKSOURCE_SYSCLK) + +#define IS_RCC_I2S3CLKSOURCE(__SOURCE__) ((__SOURCE__) == RCC_I2S3CLKSOURCE_SYSCLK) + +#define IS_RCC_PERIPHCLOCK(__SELECTION__) \ + ((((__SELECTION__) & RCC_PERIPHCLK_RTC) == RCC_PERIPHCLK_RTC) || \ + (((__SELECTION__) & RCC_PERIPHCLK_ADC) == RCC_PERIPHCLK_ADC) || \ + (((__SELECTION__) & RCC_PERIPHCLK_I2S2) == RCC_PERIPHCLK_I2S2) || \ + (((__SELECTION__) & RCC_PERIPHCLK_I2S3) == RCC_PERIPHCLK_I2S3) || \ + (((__SELECTION__) & RCC_PERIPHCLK_USB) == RCC_PERIPHCLK_USB)) + + +#elif defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6)\ + || defined(STM32F103xB) + +#define IS_RCC_PERIPHCLOCK(__SELECTION__) \ + ((((__SELECTION__) & RCC_PERIPHCLK_RTC) == RCC_PERIPHCLK_RTC) || \ + (((__SELECTION__) & RCC_PERIPHCLK_ADC) == RCC_PERIPHCLK_ADC) || \ + (((__SELECTION__) & RCC_PERIPHCLK_USB) == RCC_PERIPHCLK_USB)) + +#else + +#define IS_RCC_PERIPHCLOCK(__SELECTION__) \ + ((((__SELECTION__) & RCC_PERIPHCLK_RTC) == RCC_PERIPHCLK_RTC) || \ + (((__SELECTION__) & RCC_PERIPHCLK_ADC) == RCC_PERIPHCLK_ADC)) + +#endif /* STM32F105xC || STM32F107xC */ + +#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6)\ + || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG) + +#define IS_RCC_USBPLLCLK_DIV(__USBCLK__) (((__USBCLK__) == RCC_USBCLKSOURCE_PLL) || ((__USBCLK__) == RCC_USBCLKSOURCE_PLL_DIV1_5)) + +#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG */ + +/** + * @} + */ + +/* Exported types ------------------------------------------------------------*/ + +/** @defgroup RCCEx_Exported_Types RCCEx Exported Types + * @{ + */ + +#if defined(STM32F105xC) || defined(STM32F107xC) +/** + * @brief RCC PLL2 configuration structure definition + */ +typedef struct +{ + uint32_t PLL2State; /*!< The new state of the PLL2. + This parameter can be a value of @ref RCCEx_PLL2_Config */ + + uint32_t PLL2MUL; /*!< PLL2MUL: Multiplication factor for PLL2 VCO input clock + This parameter must be a value of @ref RCCEx_PLL2_Multiplication_Factor*/ + +#if defined(STM32F105xC) || defined(STM32F107xC) + uint32_t HSEPrediv2Value; /*!< The Prediv2 factor value. + This parameter can be a value of @ref RCCEx_Prediv2_Factor */ + +#endif /* STM32F105xC || STM32F107xC */ +} RCC_PLL2InitTypeDef; + +#endif /* STM32F105xC || STM32F107xC */ + +/** + * @brief RCC Internal/External Oscillator (HSE, HSI, LSE and LSI) configuration structure definition + */ +typedef struct +{ + uint32_t OscillatorType; /*!< The oscillators to be configured. + This parameter can be a value of @ref RCC_Oscillator_Type */ + +#if defined(STM32F105xC) || defined(STM32F107xC) + uint32_t Prediv1Source; /*!< The Prediv1 source value. + This parameter can be a value of @ref RCCEx_Prediv1_Source */ +#endif /* STM32F105xC || STM32F107xC */ + + uint32_t HSEState; /*!< The new state of the HSE. + This parameter can be a value of @ref RCC_HSE_Config */ + + uint32_t HSEPredivValue; /*!< The Prediv1 factor value (named PREDIV1 or PLLXTPRE in RM) + This parameter can be a value of @ref RCCEx_Prediv1_Factor */ + + uint32_t LSEState; /*!< The new state of the LSE. + This parameter can be a value of @ref RCC_LSE_Config */ + + uint32_t HSIState; /*!< The new state of the HSI. + This parameter can be a value of @ref RCC_HSI_Config */ + + uint32_t HSICalibrationValue; /*!< The HSI calibration trimming value (default is RCC_HSICALIBRATION_DEFAULT). + This parameter must be a number between Min_Data = 0x00 and Max_Data = 0x1F */ + + uint32_t LSIState; /*!< The new state of the LSI. + This parameter can be a value of @ref RCC_LSI_Config */ + + RCC_PLLInitTypeDef PLL; /*!< PLL structure parameters */ + +#if defined(STM32F105xC) || defined(STM32F107xC) + RCC_PLL2InitTypeDef PLL2; /*!< PLL2 structure parameters */ +#endif /* STM32F105xC || STM32F107xC */ +} RCC_OscInitTypeDef; + +#if defined(STM32F105xC) || defined(STM32F107xC) +/** + * @brief RCC PLLI2S configuration structure definition + */ +typedef struct +{ + uint32_t PLLI2SMUL; /*!< PLLI2SMUL: Multiplication factor for PLLI2S VCO input clock + This parameter must be a value of @ref RCCEx_PLLI2S_Multiplication_Factor*/ + +#if defined(STM32F105xC) || defined(STM32F107xC) + uint32_t HSEPrediv2Value; /*!< The Prediv2 factor value. + This parameter can be a value of @ref RCCEx_Prediv2_Factor */ + +#endif /* STM32F105xC || STM32F107xC */ +} RCC_PLLI2SInitTypeDef; +#endif /* STM32F105xC || STM32F107xC */ + +/** + * @brief RCC extended clocks structure definition + */ +typedef struct +{ + uint32_t PeriphClockSelection; /*!< The Extended Clock to be configured. + This parameter can be a value of @ref RCCEx_Periph_Clock_Selection */ + + uint32_t RTCClockSelection; /*!< specifies the RTC clock source. + This parameter can be a value of @ref RCC_RTC_Clock_Source */ + + uint32_t AdcClockSelection; /*!< ADC clock source + This parameter can be a value of @ref RCCEx_ADC_Prescaler */ + +#if defined(STM32F103xE) || defined(STM32F103xG) || defined(STM32F105xC)\ + || defined(STM32F107xC) + uint32_t I2s2ClockSelection; /*!< I2S2 clock source + This parameter can be a value of @ref RCCEx_I2S2_Clock_Source */ + + uint32_t I2s3ClockSelection; /*!< I2S3 clock source + This parameter can be a value of @ref RCCEx_I2S3_Clock_Source */ + +#if defined(STM32F105xC) || defined(STM32F107xC) + RCC_PLLI2SInitTypeDef PLLI2S; /*!< PLL I2S structure parameters + This parameter will be used only when PLLI2S is selected as Clock Source I2S2 or I2S3 */ + +#endif /* STM32F105xC || STM32F107xC */ +#endif /* STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */ + +#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6)\ + || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG)\ + || defined(STM32F105xC) || defined(STM32F107xC) + uint32_t UsbClockSelection; /*!< USB clock source + This parameter can be a value of @ref RCCEx_USB_Prescaler */ + +#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */ +} RCC_PeriphCLKInitTypeDef; + +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ + +/** @defgroup RCCEx_Exported_Constants RCCEx Exported Constants + * @{ + */ + +/** @defgroup RCCEx_Periph_Clock_Selection Periph Clock Selection + * @{ + */ +#define RCC_PERIPHCLK_RTC 0x00000001U +#define RCC_PERIPHCLK_ADC 0x00000002U +#if defined(STM32F103xE) || defined(STM32F103xG) || defined(STM32F105xC)\ + || defined(STM32F107xC) +#define RCC_PERIPHCLK_I2S2 0x00000004U +#define RCC_PERIPHCLK_I2S3 0x00000008U +#endif /* STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */ +#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6)\ + || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG)\ + || defined(STM32F105xC) || defined(STM32F107xC) +#define RCC_PERIPHCLK_USB 0x00000010U +#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */ + +/** + * @} + */ + +/** @defgroup RCCEx_ADC_Prescaler ADC Prescaler + * @{ + */ +#define RCC_ADCPCLK2_DIV2 RCC_CFGR_ADCPRE_DIV2 +#define RCC_ADCPCLK2_DIV4 RCC_CFGR_ADCPRE_DIV4 +#define RCC_ADCPCLK2_DIV6 RCC_CFGR_ADCPRE_DIV6 +#define RCC_ADCPCLK2_DIV8 RCC_CFGR_ADCPRE_DIV8 + +/** + * @} + */ + +#if defined(STM32F103xE) || defined(STM32F103xG) || defined(STM32F105xC)\ + || defined(STM32F107xC) +/** @defgroup RCCEx_I2S2_Clock_Source I2S2 Clock Source + * @{ + */ +#define RCC_I2S2CLKSOURCE_SYSCLK 0x00000000U +#if defined(STM32F105xC) || defined(STM32F107xC) +#define RCC_I2S2CLKSOURCE_PLLI2S_VCO RCC_CFGR2_I2S2SRC +#endif /* STM32F105xC || STM32F107xC */ + +/** + * @} + */ + +/** @defgroup RCCEx_I2S3_Clock_Source I2S3 Clock Source + * @{ + */ +#define RCC_I2S3CLKSOURCE_SYSCLK 0x00000000U +#if defined(STM32F105xC) || defined(STM32F107xC) +#define RCC_I2S3CLKSOURCE_PLLI2S_VCO RCC_CFGR2_I2S3SRC +#endif /* STM32F105xC || STM32F107xC */ + +/** + * @} + */ + +#endif /* STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */ + +#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6)\ + || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG) + +/** @defgroup RCCEx_USB_Prescaler USB Prescaler + * @{ + */ +#define RCC_USBCLKSOURCE_PLL RCC_CFGR_USBPRE +#define RCC_USBCLKSOURCE_PLL_DIV1_5 0x00000000U + +/** + * @} + */ + +#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG */ + + +#if defined(STM32F105xC) || defined(STM32F107xC) +/** @defgroup RCCEx_USB_Prescaler USB Prescaler + * @{ + */ +#define RCC_USBCLKSOURCE_PLL_DIV2 RCC_CFGR_OTGFSPRE +#define RCC_USBCLKSOURCE_PLL_DIV3 0x00000000U + +/** + * @} + */ + +/** @defgroup RCCEx_PLLI2S_Multiplication_Factor PLLI2S Multiplication Factor + * @{ + */ + +#define RCC_PLLI2S_MUL8 RCC_CFGR2_PLL3MUL8 /*!< PLLI2S input clock * 8 */ +#define RCC_PLLI2S_MUL9 RCC_CFGR2_PLL3MUL9 /*!< PLLI2S input clock * 9 */ +#define RCC_PLLI2S_MUL10 RCC_CFGR2_PLL3MUL10 /*!< PLLI2S input clock * 10 */ +#define RCC_PLLI2S_MUL11 RCC_CFGR2_PLL3MUL11 /*!< PLLI2S input clock * 11 */ +#define RCC_PLLI2S_MUL12 RCC_CFGR2_PLL3MUL12 /*!< PLLI2S input clock * 12 */ +#define RCC_PLLI2S_MUL13 RCC_CFGR2_PLL3MUL13 /*!< PLLI2S input clock * 13 */ +#define RCC_PLLI2S_MUL14 RCC_CFGR2_PLL3MUL14 /*!< PLLI2S input clock * 14 */ +#define RCC_PLLI2S_MUL16 RCC_CFGR2_PLL3MUL16 /*!< PLLI2S input clock * 16 */ +#define RCC_PLLI2S_MUL20 RCC_CFGR2_PLL3MUL20 /*!< PLLI2S input clock * 20 */ + +/** + * @} + */ +#endif /* STM32F105xC || STM32F107xC */ + +#if defined(STM32F105xC) || defined(STM32F107xC) +/** @defgroup RCCEx_Prediv1_Source Prediv1 Source + * @{ + */ + +#define RCC_PREDIV1_SOURCE_HSE RCC_CFGR2_PREDIV1SRC_HSE +#define RCC_PREDIV1_SOURCE_PLL2 RCC_CFGR2_PREDIV1SRC_PLL2 + +/** + * @} + */ +#endif /* STM32F105xC || STM32F107xC */ + +/** @defgroup RCCEx_Prediv1_Factor HSE Prediv1 Factor + * @{ + */ + +#define RCC_HSE_PREDIV_DIV1 0x00000000U + +#if defined(STM32F105xC) || defined(STM32F107xC) || defined(STM32F100xB)\ + || defined(STM32F100xE) +#define RCC_HSE_PREDIV_DIV2 RCC_CFGR2_PREDIV1_DIV2 +#define RCC_HSE_PREDIV_DIV3 RCC_CFGR2_PREDIV1_DIV3 +#define RCC_HSE_PREDIV_DIV4 RCC_CFGR2_PREDIV1_DIV4 +#define RCC_HSE_PREDIV_DIV5 RCC_CFGR2_PREDIV1_DIV5 +#define RCC_HSE_PREDIV_DIV6 RCC_CFGR2_PREDIV1_DIV6 +#define RCC_HSE_PREDIV_DIV7 RCC_CFGR2_PREDIV1_DIV7 +#define RCC_HSE_PREDIV_DIV8 RCC_CFGR2_PREDIV1_DIV8 +#define RCC_HSE_PREDIV_DIV9 RCC_CFGR2_PREDIV1_DIV9 +#define RCC_HSE_PREDIV_DIV10 RCC_CFGR2_PREDIV1_DIV10 +#define RCC_HSE_PREDIV_DIV11 RCC_CFGR2_PREDIV1_DIV11 +#define RCC_HSE_PREDIV_DIV12 RCC_CFGR2_PREDIV1_DIV12 +#define RCC_HSE_PREDIV_DIV13 RCC_CFGR2_PREDIV1_DIV13 +#define RCC_HSE_PREDIV_DIV14 RCC_CFGR2_PREDIV1_DIV14 +#define RCC_HSE_PREDIV_DIV15 RCC_CFGR2_PREDIV1_DIV15 +#define RCC_HSE_PREDIV_DIV16 RCC_CFGR2_PREDIV1_DIV16 +#else +#define RCC_HSE_PREDIV_DIV2 RCC_CFGR_PLLXTPRE +#endif /* STM32F105xC || STM32F107xC || STM32F100xB || STM32F100xE */ + +/** + * @} + */ + +#if defined(STM32F105xC) || defined(STM32F107xC) +/** @defgroup RCCEx_Prediv2_Factor HSE Prediv2 Factor + * @{ + */ + +#define RCC_HSE_PREDIV2_DIV1 RCC_CFGR2_PREDIV2_DIV1 /*!< PREDIV2 input clock not divided */ +#define RCC_HSE_PREDIV2_DIV2 RCC_CFGR2_PREDIV2_DIV2 /*!< PREDIV2 input clock divided by 2 */ +#define RCC_HSE_PREDIV2_DIV3 RCC_CFGR2_PREDIV2_DIV3 /*!< PREDIV2 input clock divided by 3 */ +#define RCC_HSE_PREDIV2_DIV4 RCC_CFGR2_PREDIV2_DIV4 /*!< PREDIV2 input clock divided by 4 */ +#define RCC_HSE_PREDIV2_DIV5 RCC_CFGR2_PREDIV2_DIV5 /*!< PREDIV2 input clock divided by 5 */ +#define RCC_HSE_PREDIV2_DIV6 RCC_CFGR2_PREDIV2_DIV6 /*!< PREDIV2 input clock divided by 6 */ +#define RCC_HSE_PREDIV2_DIV7 RCC_CFGR2_PREDIV2_DIV7 /*!< PREDIV2 input clock divided by 7 */ +#define RCC_HSE_PREDIV2_DIV8 RCC_CFGR2_PREDIV2_DIV8 /*!< PREDIV2 input clock divided by 8 */ +#define RCC_HSE_PREDIV2_DIV9 RCC_CFGR2_PREDIV2_DIV9 /*!< PREDIV2 input clock divided by 9 */ +#define RCC_HSE_PREDIV2_DIV10 RCC_CFGR2_PREDIV2_DIV10 /*!< PREDIV2 input clock divided by 10 */ +#define RCC_HSE_PREDIV2_DIV11 RCC_CFGR2_PREDIV2_DIV11 /*!< PREDIV2 input clock divided by 11 */ +#define RCC_HSE_PREDIV2_DIV12 RCC_CFGR2_PREDIV2_DIV12 /*!< PREDIV2 input clock divided by 12 */ +#define RCC_HSE_PREDIV2_DIV13 RCC_CFGR2_PREDIV2_DIV13 /*!< PREDIV2 input clock divided by 13 */ +#define RCC_HSE_PREDIV2_DIV14 RCC_CFGR2_PREDIV2_DIV14 /*!< PREDIV2 input clock divided by 14 */ +#define RCC_HSE_PREDIV2_DIV15 RCC_CFGR2_PREDIV2_DIV15 /*!< PREDIV2 input clock divided by 15 */ +#define RCC_HSE_PREDIV2_DIV16 RCC_CFGR2_PREDIV2_DIV16 /*!< PREDIV2 input clock divided by 16 */ + +/** + * @} + */ + +/** @defgroup RCCEx_PLL2_Config PLL Config + * @{ + */ +#define RCC_PLL2_NONE 0x00000000U +#define RCC_PLL2_OFF 0x00000001U +#define RCC_PLL2_ON 0x00000002U + +/** + * @} + */ + +/** @defgroup RCCEx_PLL2_Multiplication_Factor PLL2 Multiplication Factor + * @{ + */ + +#define RCC_PLL2_MUL8 RCC_CFGR2_PLL2MUL8 /*!< PLL2 input clock * 8 */ +#define RCC_PLL2_MUL9 RCC_CFGR2_PLL2MUL9 /*!< PLL2 input clock * 9 */ +#define RCC_PLL2_MUL10 RCC_CFGR2_PLL2MUL10 /*!< PLL2 input clock * 10 */ +#define RCC_PLL2_MUL11 RCC_CFGR2_PLL2MUL11 /*!< PLL2 input clock * 11 */ +#define RCC_PLL2_MUL12 RCC_CFGR2_PLL2MUL12 /*!< PLL2 input clock * 12 */ +#define RCC_PLL2_MUL13 RCC_CFGR2_PLL2MUL13 /*!< PLL2 input clock * 13 */ +#define RCC_PLL2_MUL14 RCC_CFGR2_PLL2MUL14 /*!< PLL2 input clock * 14 */ +#define RCC_PLL2_MUL16 RCC_CFGR2_PLL2MUL16 /*!< PLL2 input clock * 16 */ +#define RCC_PLL2_MUL20 RCC_CFGR2_PLL2MUL20 /*!< PLL2 input clock * 20 */ + +/** + * @} + */ + +#endif /* STM32F105xC || STM32F107xC */ + +/** @defgroup RCCEx_PLL_Multiplication_Factor PLL Multiplication Factor + * @{ + */ + +#if defined(STM32F105xC) || defined(STM32F107xC) +#else +#define RCC_PLL_MUL2 RCC_CFGR_PLLMULL2 +#define RCC_PLL_MUL3 RCC_CFGR_PLLMULL3 +#endif /* STM32F105xC || STM32F107xC */ +#define RCC_PLL_MUL4 RCC_CFGR_PLLMULL4 +#define RCC_PLL_MUL5 RCC_CFGR_PLLMULL5 +#define RCC_PLL_MUL6 RCC_CFGR_PLLMULL6 +#define RCC_PLL_MUL7 RCC_CFGR_PLLMULL7 +#define RCC_PLL_MUL8 RCC_CFGR_PLLMULL8 +#define RCC_PLL_MUL9 RCC_CFGR_PLLMULL9 +#if defined(STM32F105xC) || defined(STM32F107xC) +#define RCC_PLL_MUL6_5 RCC_CFGR_PLLMULL6_5 +#else +#define RCC_PLL_MUL10 RCC_CFGR_PLLMULL10 +#define RCC_PLL_MUL11 RCC_CFGR_PLLMULL11 +#define RCC_PLL_MUL12 RCC_CFGR_PLLMULL12 +#define RCC_PLL_MUL13 RCC_CFGR_PLLMULL13 +#define RCC_PLL_MUL14 RCC_CFGR_PLLMULL14 +#define RCC_PLL_MUL15 RCC_CFGR_PLLMULL15 +#define RCC_PLL_MUL16 RCC_CFGR_PLLMULL16 +#endif /* STM32F105xC || STM32F107xC */ + +/** + * @} + */ + +/** @defgroup RCCEx_MCO1_Clock_Source MCO1 Clock Source + * @{ + */ +#define RCC_MCO1SOURCE_NOCLOCK ((uint32_t)RCC_CFGR_MCO_NOCLOCK) +#define RCC_MCO1SOURCE_SYSCLK ((uint32_t)RCC_CFGR_MCO_SYSCLK) +#define RCC_MCO1SOURCE_HSI ((uint32_t)RCC_CFGR_MCO_HSI) +#define RCC_MCO1SOURCE_HSE ((uint32_t)RCC_CFGR_MCO_HSE) +#define RCC_MCO1SOURCE_PLLCLK ((uint32_t)RCC_CFGR_MCO_PLLCLK_DIV2) +#if defined(STM32F105xC) || defined(STM32F107xC) +#define RCC_MCO1SOURCE_PLL2CLK ((uint32_t)RCC_CFGR_MCO_PLL2CLK) +#define RCC_MCO1SOURCE_PLL3CLK_DIV2 ((uint32_t)RCC_CFGR_MCO_PLL3CLK_DIV2) +#define RCC_MCO1SOURCE_EXT_HSE ((uint32_t)RCC_CFGR_MCO_EXT_HSE) +#define RCC_MCO1SOURCE_PLL3CLK ((uint32_t)RCC_CFGR_MCO_PLL3CLK) +#endif /* STM32F105xC || STM32F107xC*/ +/** + * @} + */ + +#if defined(STM32F105xC) || defined(STM32F107xC) +/** @defgroup RCCEx_Interrupt RCCEx Interrupt + * @{ + */ +#define RCC_IT_PLL2RDY ((uint8_t)RCC_CIR_PLL2RDYF) +#define RCC_IT_PLLI2SRDY ((uint8_t)RCC_CIR_PLL3RDYF) +/** + * @} + */ + +/** @defgroup RCCEx_Flag RCCEx Flag + * Elements values convention: 0XXYYYYYb + * - YYYYY : Flag position in the register + * - XX : Register index + * - 01: CR register + * @{ + */ +/* Flags in the CR register */ +#define RCC_FLAG_PLL2RDY ((uint8_t)((CR_REG_INDEX << 5U) | RCC_CR_PLL2RDY_Pos)) +#define RCC_FLAG_PLLI2SRDY ((uint8_t)((CR_REG_INDEX << 5U) | RCC_CR_PLL3RDY_Pos)) +/** + * @} + */ +#endif /* STM32F105xC || STM32F107xC*/ + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup RCCEx_Exported_Macros RCCEx Exported Macros + * @{ + */ + +/** @defgroup RCCEx_Peripheral_Clock_Enable_Disable Peripheral Clock Enable Disable + * @brief Enable or disable the AHB1 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ + +#if defined(STM32F101xE) || defined(STM32F103xE) || defined(STM32F101xG)\ + || defined(STM32F103xG) || defined(STM32F105xC) || defined (STM32F107xC)\ + || defined (STM32F100xE) +#define __HAL_RCC_DMA2_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHBENR, RCC_AHBENR_DMA2EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_DMA2EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_DMA2_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_DMA2EN)) +#endif /* STM32F101xE || STM32F103xE || STM32F101xG || STM32F103xG || STM32F105xC || STM32F107xC || STM32F100xE */ + +#if defined(STM32F101xE) || defined(STM32F103xE) || defined(STM32F101xG)\ + || defined(STM32F103xG) || defined (STM32F100xE) +#define __HAL_RCC_FSMC_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHBENR, RCC_AHBENR_FSMCEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_FSMCEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_FSMC_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_FSMCEN)) +#endif /* STM32F101xE || STM32F103xE || STM32F101xG || STM32F103xG || STM32F100xE */ + +#if defined(STM32F103xE) || defined(STM32F103xG) +#define __HAL_RCC_SDIO_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHBENR, RCC_AHBENR_SDIOEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_SDIOEN);\ + UNUSED(tmpreg); \ + } while(0U) + + +#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_SDIOEN)) +#endif /* STM32F103xE || STM32F103xG */ + +#if defined(STM32F105xC) || defined(STM32F107xC) +#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHBENR, RCC_AHBENR_OTGFSEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_OTGFSEN);\ + UNUSED(tmpreg); \ + } while(0U) + + +#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_OTGFSEN)) +#endif /* STM32F105xC || STM32F107xC*/ + +#if defined(STM32F107xC) +#define __HAL_RCC_ETHMAC_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHBENR, RCC_AHBENR_ETHMACEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_ETHMACEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_ETHMACTX_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHBENR, RCC_AHBENR_ETHMACTXEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_ETHMACTXEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_ETHMACRX_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHBENR, RCC_AHBENR_ETHMACRXEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_ETHMACRXEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_ETHMAC_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_ETHMACEN)) +#define __HAL_RCC_ETHMACTX_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_ETHMACTXEN)) +#define __HAL_RCC_ETHMACRX_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_ETHMACRXEN)) + +/** + * @brief Enable ETHERNET clock. + */ +#define __HAL_RCC_ETH_CLK_ENABLE() do { \ + __HAL_RCC_ETHMAC_CLK_ENABLE(); \ + __HAL_RCC_ETHMACTX_CLK_ENABLE(); \ + __HAL_RCC_ETHMACRX_CLK_ENABLE(); \ + } while(0U) +/** + * @brief Disable ETHERNET clock. + */ +#define __HAL_RCC_ETH_CLK_DISABLE() do { \ + __HAL_RCC_ETHMACTX_CLK_DISABLE(); \ + __HAL_RCC_ETHMACRX_CLK_DISABLE(); \ + __HAL_RCC_ETHMAC_CLK_DISABLE(); \ + } while(0U) + +#endif /* STM32F107xC*/ + +/** + * @} + */ + +/** @defgroup RCCEx_AHB1_Peripheral_Clock_Enable_Disable_Status AHB1 Peripheral Clock Enable Disable Status + * @brief Get the enable or disable status of the AHB1 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ + +#if defined(STM32F101xE) || defined(STM32F103xE) || defined(STM32F101xG)\ + || defined(STM32F103xG) || defined(STM32F105xC) || defined (STM32F107xC)\ + || defined (STM32F100xE) +#define __HAL_RCC_DMA2_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_DMA2EN)) != RESET) +#define __HAL_RCC_DMA2_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_DMA2EN)) == RESET) +#endif /* STM32F101xE || STM32F103xE || STM32F101xG || STM32F103xG || STM32F105xC || STM32F107xC || STM32F100xE */ +#if defined(STM32F101xE) || defined(STM32F103xE) || defined(STM32F101xG)\ + || defined(STM32F103xG) || defined (STM32F100xE) +#define __HAL_RCC_FSMC_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_FSMCEN)) != RESET) +#define __HAL_RCC_FSMC_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_FSMCEN)) == RESET) +#endif /* STM32F101xE || STM32F103xE || STM32F101xG || STM32F103xG || STM32F100xE */ +#if defined(STM32F103xE) || defined(STM32F103xG) +#define __HAL_RCC_SDIO_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_SDIOEN)) != RESET) +#define __HAL_RCC_SDIO_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_SDIOEN)) == RESET) +#endif /* STM32F103xE || STM32F103xG */ +#if defined(STM32F105xC) || defined(STM32F107xC) +#define __HAL_RCC_USB_OTG_FS_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_OTGFSEN)) != RESET) +#define __HAL_RCC_USB_OTG_FS_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_OTGFSEN)) == RESET) +#endif /* STM32F105xC || STM32F107xC*/ +#if defined(STM32F107xC) +#define __HAL_RCC_ETHMAC_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_ETHMACEN)) != RESET) +#define __HAL_RCC_ETHMAC_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_ETHMACEN)) == RESET) +#define __HAL_RCC_ETHMACTX_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_ETHMACTXEN)) != RESET) +#define __HAL_RCC_ETHMACTX_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_ETHMACTXEN)) == RESET) +#define __HAL_RCC_ETHMACRX_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_ETHMACRXEN)) != RESET) +#define __HAL_RCC_ETHMACRX_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_ETHMACRXEN)) == RESET) +#endif /* STM32F107xC*/ + +/** + * @} + */ + +/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Clock Enable Disable + * @brief Enable or disable the Low Speed APB (APB1) peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ + +#if defined(STM32F103x6) || defined(STM32F103xB) || defined(STM32F103xE)\ + || defined(STM32F103xG) || defined(STM32F105xC) ||defined(STM32F107xC) +#define __HAL_RCC_CAN1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN1EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN1EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_CAN1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN1EN)) +#endif /* STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */ + +#if defined(STM32F100xB) || defined(STM32F100xE) || defined(STM32F101xB)\ + || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F102xB)\ + || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG)\ + || defined(STM32F105xC) || defined(STM32F107xC) +#define __HAL_RCC_TIM4_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_SPI2_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI2EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI2EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_USART3_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_USART3EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_USART3EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_I2C2_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C2EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C2EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN)) +#define __HAL_RCC_SPI2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI2EN)) +#define __HAL_RCC_USART3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_USART3EN)) +#define __HAL_RCC_I2C2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C2EN)) +#endif /* STM32F100xB || STM32F101xB || STM32F101xE || (...) || STM32F105xC || STM32F107xC */ + +#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6)\ + || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG) +#define __HAL_RCC_USB_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_USBEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_USBEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_USB_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_USBEN)) +#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG */ + +#if defined(STM32F101xE) || defined(STM32F103xE) || defined(STM32F101xG)\ + || defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC) +#define __HAL_RCC_TIM5_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM5EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM5EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM6_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM7_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM7EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM7EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_SPI3_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_UART4_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_UART4EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_UART4EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_UART5_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_UART5EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_UART5EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_DAC_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM5_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM5EN)) +#define __HAL_RCC_TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN)) +#define __HAL_RCC_TIM7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM7EN)) +#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN)) +#define __HAL_RCC_UART4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART4EN)) +#define __HAL_RCC_UART5_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART5EN)) +#define __HAL_RCC_DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN)) +#endif /* STM32F101xE || STM32F103xE || STM32F101xG || (...) || STM32F105xC || STM32F107xC */ + +#if defined(STM32F100xB) || defined (STM32F100xE) +#define __HAL_RCC_TIM6_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM7_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM7EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM7EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_DAC_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_CEC_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_CECEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_CECEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN)) +#define __HAL_RCC_TIM7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM7EN)) +#define __HAL_RCC_DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN)) +#define __HAL_RCC_CEC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CECEN)) +#endif /* STM32F100xB || STM32F100xE */ + +#ifdef STM32F100xE +#define __HAL_RCC_TIM5_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM5EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM5EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM12_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM12EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM12EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM13_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM13EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM13EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM14_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_SPI3_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_UART4_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_UART4EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_UART4EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_UART5_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_UART5EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_UART5EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM5_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM5EN)) +#define __HAL_RCC_TIM12_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM12EN)) +#define __HAL_RCC_TIM13_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM13EN)) +#define __HAL_RCC_TIM14_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM14EN)) +#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN)) +#define __HAL_RCC_UART4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART4EN)) +#define __HAL_RCC_UART5_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART5EN)) +#endif /* STM32F100xE */ + +#if defined(STM32F105xC) || defined(STM32F107xC) +#define __HAL_RCC_CAN2_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN2EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN2EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_CAN2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN2EN)) +#endif /* STM32F105xC || STM32F107xC */ + +#if defined(STM32F101xG) || defined(STM32F103xG) +#define __HAL_RCC_TIM12_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM12EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM12EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM13_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM13EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM13EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM14_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM12_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM12EN)) +#define __HAL_RCC_TIM13_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM13EN)) +#define __HAL_RCC_TIM14_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM14EN)) +#endif /* STM32F101xG || STM32F103xG*/ + +/** + * @} + */ + +/** @defgroup RCCEx_APB1_Peripheral_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status + * @brief Get the enable or disable status of the APB1 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ + +#if defined(STM32F103x6) || defined(STM32F103xB) || defined(STM32F103xE)\ + || defined(STM32F103xG) || defined(STM32F105xC) ||defined(STM32F107xC) +#define __HAL_RCC_CAN1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN1EN)) != RESET) +#define __HAL_RCC_CAN1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN1EN)) == RESET) +#endif /* STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */ +#if defined(STM32F100xB) || defined(STM32F100xE) || defined(STM32F101xB)\ + || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F102xB)\ + || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG)\ + || defined(STM32F105xC) || defined(STM32F107xC) +#define __HAL_RCC_TIM4_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM4EN)) != RESET) +#define __HAL_RCC_TIM4_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM4EN)) == RESET) +#define __HAL_RCC_SPI2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI2EN)) != RESET) +#define __HAL_RCC_SPI2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI2EN)) == RESET) +#define __HAL_RCC_USART3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART3EN)) != RESET) +#define __HAL_RCC_USART3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART3EN)) == RESET) +#define __HAL_RCC_I2C2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C2EN)) != RESET) +#define __HAL_RCC_I2C2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C2EN)) == RESET) +#endif /* STM32F100xB || STM32F101xB || STM32F101xE || (...) || STM32F105xC || STM32F107xC */ +#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6)\ + || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG) +#define __HAL_RCC_USB_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USBEN)) != RESET) +#define __HAL_RCC_USB_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USBEN)) == RESET) +#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG */ +#if defined(STM32F101xE) || defined(STM32F103xE) || defined(STM32F101xG)\ + || defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC) +#define __HAL_RCC_TIM5_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM5EN)) != RESET) +#define __HAL_RCC_TIM5_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM5EN)) == RESET) +#define __HAL_RCC_TIM6_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM6EN)) != RESET) +#define __HAL_RCC_TIM6_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM6EN)) == RESET) +#define __HAL_RCC_TIM7_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM7EN)) != RESET) +#define __HAL_RCC_TIM7_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM7EN)) == RESET) +#define __HAL_RCC_SPI3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) != RESET) +#define __HAL_RCC_SPI3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) == RESET) +#define __HAL_RCC_UART4_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART4EN)) != RESET) +#define __HAL_RCC_UART4_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART4EN)) == RESET) +#define __HAL_RCC_UART5_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART5EN)) != RESET) +#define __HAL_RCC_UART5_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART5EN)) == RESET) +#define __HAL_RCC_DAC_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_DACEN)) != RESET) +#define __HAL_RCC_DAC_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_DACEN)) == RESET) +#endif /* STM32F101xE || STM32F103xE || STM32F101xG || (...) || STM32F105xC || STM32F107xC */ +#if defined(STM32F100xB) || defined (STM32F100xE) +#define __HAL_RCC_TIM6_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM6EN)) != RESET) +#define __HAL_RCC_TIM6_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM6EN)) == RESET) +#define __HAL_RCC_TIM7_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM7EN)) != RESET) +#define __HAL_RCC_TIM7_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM7EN)) == RESET) +#define __HAL_RCC_DAC_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_DACEN)) != RESET) +#define __HAL_RCC_DAC_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_DACEN)) == RESET) +#define __HAL_RCC_CEC_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CECEN)) != RESET) +#define __HAL_RCC_CEC_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CECEN)) == RESET) +#endif /* STM32F100xB || STM32F100xE */ +#ifdef STM32F100xE +#define __HAL_RCC_TIM5_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM5EN)) != RESET) +#define __HAL_RCC_TIM5_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM5EN)) == RESET) +#define __HAL_RCC_TIM12_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM12EN)) != RESET) +#define __HAL_RCC_TIM12_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM12EN)) == RESET) +#define __HAL_RCC_TIM13_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM13EN)) != RESET) +#define __HAL_RCC_TIM13_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM13EN)) == RESET) +#define __HAL_RCC_TIM14_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM14EN)) != RESET) +#define __HAL_RCC_TIM14_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM14EN)) == RESET) +#define __HAL_RCC_SPI3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) != RESET) +#define __HAL_RCC_SPI3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) == RESET) +#define __HAL_RCC_UART4_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART4EN)) != RESET) +#define __HAL_RCC_UART4_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART4EN)) == RESET) +#define __HAL_RCC_UART5_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART5EN)) != RESET) +#define __HAL_RCC_UART5_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART5EN)) == RESET) +#define __HAL_RCC_CAN2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN2EN)) != RESET) +#define __HAL_RCC_CAN2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN2EN)) == RESET) +#endif /* STM32F100xE */ +#if defined(STM32F105xC) || defined(STM32F107xC) +#define __HAL_RCC_TIM12_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM12EN)) != RESET) +#define __HAL_RCC_TIM12_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM12EN)) == RESET) +#endif /* STM32F105xC || STM32F107xC */ +#if defined(STM32F101xG) || defined(STM32F103xG) +#define __HAL_RCC_TIM13_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM13EN)) != RESET) +#define __HAL_RCC_TIM13_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM13EN)) == RESET) +#define __HAL_RCC_TIM14_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM14EN)) != RESET) +#define __HAL_RCC_TIM14_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM14EN)) == RESET) +#endif /* STM32F101xG || STM32F103xG*/ + +/** + * @} + */ + +/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Clock Enable Disable + * @brief Enable or disable the High Speed APB (APB2) peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ + +#if defined(STM32F101xG) || defined(STM32F103x6) || defined(STM32F103xB)\ + || defined(STM32F105xC) || defined(STM32F107xC) || defined(STM32F103xE)\ + || defined(STM32F103xG) +#define __HAL_RCC_ADC2_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC2EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC2EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN)) +#endif /* STM32F101xG || STM32F103x6 || STM32F103xB || STM32F105xC || STM32F107xC || STM32F103xE || STM32F103xG */ + +#if defined(STM32F100xB) || defined(STM32F100xE) +#define __HAL_RCC_TIM15_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM15EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM15EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM16_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM16EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM16EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM17_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM17EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM17EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM15_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM15EN)) +#define __HAL_RCC_TIM16_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM16EN)) +#define __HAL_RCC_TIM17_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM17EN)) +#endif /* STM32F100xB || STM32F100xE */ + +#if defined(STM32F100xE) || defined(STM32F101xB) || defined(STM32F101xE)\ + || defined(STM32F101xG) || defined(STM32F100xB) || defined(STM32F103xB)\ + || defined(STM32F103xE) || defined(STM32F103xG) || defined(STM32F105xC)\ + || defined(STM32F107xC) +#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPEEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPEEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPEEN)) +#endif /* STM32F101x6 || STM32F101xB || STM32F101xE || (...) || STM32F105xC || STM32F107xC */ + +#if defined(STM32F101xE) || defined(STM32F103xE) || defined(STM32F101xG)\ + || defined(STM32F103xG) +#define __HAL_RCC_GPIOF_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPFEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPFEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_GPIOG_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPGEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPGEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_GPIOF_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPFEN)) +#define __HAL_RCC_GPIOG_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPGEN)) +#endif /* STM32F101xE || STM32F103xE || STM32F101xG || STM32F103xG*/ + +#if defined(STM32F103xE) || defined(STM32F103xG) +#define __HAL_RCC_TIM8_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_ADC3_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC3EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC3EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN)) +#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN)) +#endif /* STM32F103xE || STM32F103xG */ + +#if defined(STM32F100xE) +#define __HAL_RCC_GPIOF_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPFEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPFEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_GPIOG_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPGEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPGEN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_GPIOF_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPFEN)) +#define __HAL_RCC_GPIOG_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPGEN)) +#endif /* STM32F100xE */ + +#if defined(STM32F101xG) || defined(STM32F103xG) +#define __HAL_RCC_TIM9_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM9EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM9EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM10_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM11_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM11EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM11EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM9_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM9EN)) +#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN)) +#define __HAL_RCC_TIM11_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM11EN)) +#endif /* STM32F101xG || STM32F103xG */ + +/** + * @} + */ + +/** @defgroup RCCEx_APB2_Peripheral_Clock_Enable_Disable_Status APB2 Peripheral Clock Enable Disable Status + * @brief Get the enable or disable status of the APB2 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ + +#if defined(STM32F101xG) || defined(STM32F103x6) || defined(STM32F103xB)\ + || defined(STM32F105xC) || defined(STM32F107xC) || defined(STM32F103xE)\ + || defined(STM32F103xG) +#define __HAL_RCC_ADC2_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC2EN)) != RESET) +#define __HAL_RCC_ADC2_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC2EN)) == RESET) +#endif /* STM32F101xG || STM32F103x6 || STM32F103xB || STM32F105xC || STM32F107xC || STM32F103xE || STM32F103xG */ +#if defined(STM32F100xB) || defined(STM32F100xE) +#define __HAL_RCC_TIM15_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM15EN)) != RESET) +#define __HAL_RCC_TIM15_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM15EN)) == RESET) +#define __HAL_RCC_TIM16_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM16EN)) != RESET) +#define __HAL_RCC_TIM16_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM16EN)) == RESET) +#define __HAL_RCC_TIM17_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM17EN)) != RESET) +#define __HAL_RCC_TIM17_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM17EN)) == RESET) +#endif /* STM32F100xB || STM32F100xE */ +#if defined(STM32F100xE) || defined(STM32F101xB) || defined(STM32F101xE)\ + || defined(STM32F101xG) || defined(STM32F100xB) || defined(STM32F103xB)\ + || defined(STM32F103xE) || defined(STM32F103xG) || defined(STM32F105xC)\ + || defined(STM32F107xC) +#define __HAL_RCC_GPIOE_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPEEN)) != RESET) +#define __HAL_RCC_GPIOE_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPEEN)) == RESET) +#endif /* STM32F101x6 || STM32F101xB || STM32F101xE || (...) || STM32F105xC || STM32F107xC */ +#if defined(STM32F101xE) || defined(STM32F103xE) || defined(STM32F101xG)\ + || defined(STM32F103xG) +#define __HAL_RCC_GPIOF_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPFEN)) != RESET) +#define __HAL_RCC_GPIOF_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPFEN)) == RESET) +#define __HAL_RCC_GPIOG_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPGEN)) != RESET) +#define __HAL_RCC_GPIOG_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPGEN)) == RESET) +#endif /* STM32F101xE || STM32F103xE || STM32F101xG || STM32F103xG*/ +#if defined(STM32F103xE) || defined(STM32F103xG) +#define __HAL_RCC_TIM8_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM8EN)) != RESET) +#define __HAL_RCC_TIM8_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM8EN)) == RESET) +#define __HAL_RCC_ADC3_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC3EN)) != RESET) +#define __HAL_RCC_ADC3_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC3EN)) == RESET) +#endif /* STM32F103xE || STM32F103xG */ +#if defined(STM32F100xE) +#define __HAL_RCC_GPIOF_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPFEN)) != RESET) +#define __HAL_RCC_GPIOF_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPFEN)) == RESET) +#define __HAL_RCC_GPIOG_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPGEN)) != RESET) +#define __HAL_RCC_GPIOG_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPGEN)) == RESET) +#endif /* STM32F100xE */ +#if defined(STM32F101xG) || defined(STM32F103xG) +#define __HAL_RCC_TIM9_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM9EN)) != RESET) +#define __HAL_RCC_TIM9_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM9EN)) == RESET) +#define __HAL_RCC_TIM10_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM10EN)) != RESET) +#define __HAL_RCC_TIM10_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM10EN)) == RESET) +#define __HAL_RCC_TIM11_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM11EN)) != RESET) +#define __HAL_RCC_TIM11_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM11EN)) == RESET) +#endif /* STM32F101xG || STM32F103xG */ + +/** + * @} + */ + +#if defined(STM32F105xC) || defined(STM32F107xC) +/** @defgroup RCCEx_Peripheral_Clock_Force_Release Peripheral Clock Force Release + * @brief Force or release AHB peripheral reset. + * @{ + */ +#define __HAL_RCC_AHB_FORCE_RESET() (RCC->AHBRSTR = 0xFFFFFFFFU) +#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHBRSTR |= (RCC_AHBRSTR_OTGFSRST)) +#if defined(STM32F107xC) +#define __HAL_RCC_ETHMAC_FORCE_RESET() (RCC->AHBRSTR |= (RCC_AHBRSTR_ETHMACRST)) +#endif /* STM32F107xC */ + +#define __HAL_RCC_AHB_RELEASE_RESET() (RCC->AHBRSTR = 0x00) +#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHBRSTR &= ~(RCC_AHBRSTR_OTGFSRST)) +#if defined(STM32F107xC) +#define __HAL_RCC_ETHMAC_RELEASE_RESET() (RCC->AHBRSTR &= ~(RCC_AHBRSTR_ETHMACRST)) +#endif /* STM32F107xC */ + +/** + * @} + */ +#endif /* STM32F105xC || STM32F107xC */ + +/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset + * @brief Force or release APB1 peripheral reset. + * @{ + */ + +#if defined(STM32F103x6) || defined(STM32F103xB) || defined(STM32F103xE)\ + || defined(STM32F103xG) || defined(STM32F105xC) ||defined(STM32F107xC) +#define __HAL_RCC_CAN1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN1RST)) + +#define __HAL_RCC_CAN1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN1RST)) +#endif /* STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */ + +#if defined(STM32F100xB) || defined(STM32F100xE) || defined(STM32F101xB)\ + || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F102xB)\ + || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG)\ + || defined(STM32F105xC) || defined(STM32F107xC) +#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST)) +#define __HAL_RCC_SPI2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI2RST)) +#define __HAL_RCC_USART3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USART3RST)) +#define __HAL_RCC_I2C2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C2RST)) + +#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST)) +#define __HAL_RCC_SPI2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI2RST)) +#define __HAL_RCC_USART3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_USART3RST)) +#define __HAL_RCC_I2C2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C2RST)) +#endif /* STM32F100xB || STM32F101xB || STM32F101xE || (...) || STM32F105xC || STM32F107xC */ + +#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6)\ + || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG) +#define __HAL_RCC_USB_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USBRST)) +#define __HAL_RCC_USB_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_USBRST)) +#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG */ + +#if defined(STM32F101xE) || defined(STM32F103xE) || defined(STM32F101xG)\ + || defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC) +#define __HAL_RCC_TIM5_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM5RST)) +#define __HAL_RCC_TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST)) +#define __HAL_RCC_TIM7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM7RST)) +#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST)) +#define __HAL_RCC_UART4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART4RST)) +#define __HAL_RCC_UART5_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART5RST)) +#define __HAL_RCC_DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST)) + +#define __HAL_RCC_TIM5_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM5RST)) +#define __HAL_RCC_TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST)) +#define __HAL_RCC_TIM7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM7RST)) +#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST)) +#define __HAL_RCC_UART4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART4RST)) +#define __HAL_RCC_UART5_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART5RST)) +#define __HAL_RCC_DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST)) +#endif /* STM32F101xE || STM32F103xE || STM32F101xG || (...) || STM32F105xC || STM32F107xC */ + +#if defined(STM32F100xB) || defined (STM32F100xE) +#define __HAL_RCC_TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST)) +#define __HAL_RCC_TIM7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM7RST)) +#define __HAL_RCC_DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST)) +#define __HAL_RCC_CEC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CECRST)) + +#define __HAL_RCC_TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST)) +#define __HAL_RCC_TIM7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM7RST)) +#define __HAL_RCC_DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST)) +#define __HAL_RCC_CEC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CECRST)) +#endif /* STM32F100xB || STM32F100xE */ + +#if defined (STM32F100xE) +#define __HAL_RCC_TIM5_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM5RST)) +#define __HAL_RCC_TIM12_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM12RST)) +#define __HAL_RCC_TIM13_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM13RST)) +#define __HAL_RCC_TIM14_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM14RST)) +#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST)) +#define __HAL_RCC_UART4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART4RST)) +#define __HAL_RCC_UART5_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART5RST)) + +#define __HAL_RCC_TIM5_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM5RST)) +#define __HAL_RCC_TIM12_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM12RST)) +#define __HAL_RCC_TIM13_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM13RST)) +#define __HAL_RCC_TIM14_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM14RST)) +#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST)) +#define __HAL_RCC_UART4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART4RST)) +#define __HAL_RCC_UART5_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART5RST)) +#endif /* STM32F100xE */ + +#if defined(STM32F105xC) || defined(STM32F107xC) +#define __HAL_RCC_CAN2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN2RST)) + +#define __HAL_RCC_CAN2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN2RST)) +#endif /* STM32F105xC || STM32F107xC */ + +#if defined(STM32F101xG) || defined(STM32F103xG) +#define __HAL_RCC_TIM12_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM12RST)) +#define __HAL_RCC_TIM13_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM13RST)) +#define __HAL_RCC_TIM14_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM14RST)) + +#define __HAL_RCC_TIM12_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM12RST)) +#define __HAL_RCC_TIM13_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM13RST)) +#define __HAL_RCC_TIM14_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM14RST)) +#endif /* STM32F101xG || STM32F103xG */ + +/** + * @} + */ + +/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset + * @brief Force or release APB2 peripheral reset. + * @{ + */ + +#if defined(STM32F101xG) || defined(STM32F103x6) || defined(STM32F103xB)\ + || defined(STM32F105xC) || defined(STM32F107xC) || defined(STM32F103xE)\ + || defined(STM32F103xG) +#define __HAL_RCC_ADC2_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_ADC2RST)) + +#define __HAL_RCC_ADC2_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_ADC2RST)) +#endif /* STM32F101xG || STM32F103x6 || STM32F103xB || STM32F105xC || STM32F107xC || STM32F103xE || STM32F103xG */ + +#if defined(STM32F100xB) || defined(STM32F100xE) +#define __HAL_RCC_TIM15_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM15RST)) +#define __HAL_RCC_TIM16_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM16RST)) +#define __HAL_RCC_TIM17_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM17RST)) + +#define __HAL_RCC_TIM15_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM15RST)) +#define __HAL_RCC_TIM16_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM16RST)) +#define __HAL_RCC_TIM17_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM17RST)) +#endif /* STM32F100xB || STM32F100xE */ + +#if defined(STM32F100xE) || defined(STM32F101xB) || defined(STM32F101xE)\ + || defined(STM32F101xG) || defined(STM32F100xB) || defined(STM32F103xB)\ + || defined(STM32F103xE) || defined(STM32F103xG) || defined(STM32F105xC)\ + || defined(STM32F107xC) +#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPERST)) + +#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPERST)) +#endif /* STM32F101x6 || STM32F101xB || STM32F101xE || (...) || STM32F105xC || STM32F107xC */ + +#if defined(STM32F101xE) || defined(STM32F103xE) || defined(STM32F101xG)\ + || defined(STM32F103xG) +#define __HAL_RCC_GPIOF_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPFRST)) +#define __HAL_RCC_GPIOG_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPGRST)) + +#define __HAL_RCC_GPIOF_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPFRST)) +#define __HAL_RCC_GPIOG_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPGRST)) +#endif /* STM32F101xE || STM32F103xE || STM32F101xG || STM32F103xG*/ + +#if defined(STM32F103xE) || defined(STM32F103xG) +#define __HAL_RCC_TIM8_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM8RST)) +#define __HAL_RCC_ADC3_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_ADC3RST)) + +#define __HAL_RCC_TIM8_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM8RST)) +#define __HAL_RCC_ADC3_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_ADC3RST)) +#endif /* STM32F103xE || STM32F103xG */ + +#if defined(STM32F100xE) +#define __HAL_RCC_GPIOF_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPFRST)) +#define __HAL_RCC_GPIOG_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPGRST)) + +#define __HAL_RCC_GPIOF_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPFRST)) +#define __HAL_RCC_GPIOG_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPGRST)) +#endif /* STM32F100xE */ + +#if defined(STM32F101xG) || defined(STM32F103xG) +#define __HAL_RCC_TIM9_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM9RST)) +#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST)) +#define __HAL_RCC_TIM11_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM11RST)) + +#define __HAL_RCC_TIM9_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM9RST)) +#define __HAL_RCC_TIM10_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST)) +#define __HAL_RCC_TIM11_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM11RST)) +#endif /* STM32F101xG || STM32F103xG*/ + +/** + * @} + */ + +/** @defgroup RCCEx_HSE_Configuration HSE Configuration + * @{ + */ + +#if defined(STM32F105xC) || defined(STM32F107xC) || defined(STM32F100xB)\ + || defined(STM32F100xE) +/** + * @brief Macro to configure the External High Speed oscillator (HSE) Predivision factor for PLL. + * @note Predivision factor can not be changed if PLL is used as system clock + * In this case, you have to select another source of the system clock, disable the PLL and + * then change the HSE predivision factor. + * @param __HSE_PREDIV_VALUE__ specifies the division value applied to HSE. + * This parameter must be a number between RCC_HSE_PREDIV_DIV1 and RCC_HSE_PREDIV_DIV16. + */ +#define __HAL_RCC_HSE_PREDIV_CONFIG(__HSE_PREDIV_VALUE__) MODIFY_REG(RCC->CFGR2, RCC_CFGR2_PREDIV1, (uint32_t)(__HSE_PREDIV_VALUE__)) +#else +/** + * @brief Macro to configure the External High Speed oscillator (HSE) Predivision factor for PLL. + * @note Predivision factor can not be changed if PLL is used as system clock + * In this case, you have to select another source of the system clock, disable the PLL and + * then change the HSE predivision factor. + * @param __HSE_PREDIV_VALUE__ specifies the division value applied to HSE. + * This parameter must be a number between RCC_HSE_PREDIV_DIV1 and RCC_HSE_PREDIV_DIV2. + */ +#define __HAL_RCC_HSE_PREDIV_CONFIG(__HSE_PREDIV_VALUE__) \ + MODIFY_REG(RCC->CFGR,RCC_CFGR_PLLXTPRE, (uint32_t)(__HSE_PREDIV_VALUE__)) + +#endif /* STM32F105xC || STM32F107xC */ + +#if defined(STM32F105xC) || defined(STM32F107xC) || defined(STM32F100xB)\ + || defined(STM32F100xE) +/** + * @brief Macro to get prediv1 factor for PLL. + */ +#define __HAL_RCC_HSE_GET_PREDIV() READ_BIT(RCC->CFGR2, RCC_CFGR2_PREDIV1) + +#else +/** + * @brief Macro to get prediv1 factor for PLL. + */ +#define __HAL_RCC_HSE_GET_PREDIV() READ_BIT(RCC->CFGR, RCC_CFGR_PLLXTPRE) + +#endif /* STM32F105xC || STM32F107xC || STM32F100xB || STM32F100xE */ + +/** + * @} + */ + +#if defined(STM32F105xC) || defined(STM32F107xC) +/** @defgroup RCCEx_PLLI2S_Configuration PLLI2S Configuration + * @{ + */ + +/** @brief Macros to enable the main PLLI2S. + * @note After enabling the main PLLI2S, the application software should wait on + * PLLI2SRDY flag to be set indicating that PLLI2S clock is stable and can + * be used as system clock source. + * @note The main PLLI2S is disabled by hardware when entering STOP and STANDBY modes. + */ +#define __HAL_RCC_PLLI2S_ENABLE() (*(__IO uint32_t *) RCC_CR_PLLI2SON_BB = ENABLE) + +/** @brief Macros to disable the main PLLI2S. + * @note The main PLLI2S is disabled by hardware when entering STOP and STANDBY modes. + */ +#define __HAL_RCC_PLLI2S_DISABLE() (*(__IO uint32_t *) RCC_CR_PLLI2SON_BB = DISABLE) + +/** @brief macros to configure the main PLLI2S multiplication factor. + * @note This function must be used only when the main PLLI2S is disabled. + * + * @param __PLLI2SMUL__ specifies the multiplication factor for PLLI2S VCO output clock + * This parameter can be one of the following values: + * @arg @ref RCC_PLLI2S_MUL8 PLLI2SVCO = PLLI2S clock entry x 8 + * @arg @ref RCC_PLLI2S_MUL9 PLLI2SVCO = PLLI2S clock entry x 9 + * @arg @ref RCC_PLLI2S_MUL10 PLLI2SVCO = PLLI2S clock entry x 10 + * @arg @ref RCC_PLLI2S_MUL11 PLLI2SVCO = PLLI2S clock entry x 11 + * @arg @ref RCC_PLLI2S_MUL12 PLLI2SVCO = PLLI2S clock entry x 12 + * @arg @ref RCC_PLLI2S_MUL13 PLLI2SVCO = PLLI2S clock entry x 13 + * @arg @ref RCC_PLLI2S_MUL14 PLLI2SVCO = PLLI2S clock entry x 14 + * @arg @ref RCC_PLLI2S_MUL16 PLLI2SVCO = PLLI2S clock entry x 16 + * @arg @ref RCC_PLLI2S_MUL20 PLLI2SVCO = PLLI2S clock entry x 20 + * + */ +#define __HAL_RCC_PLLI2S_CONFIG(__PLLI2SMUL__)\ + MODIFY_REG(RCC->CFGR2, RCC_CFGR2_PLL3MUL,(__PLLI2SMUL__)) + +/** + * @} + */ + +#endif /* STM32F105xC || STM32F107xC */ + +/** @defgroup RCCEx_Peripheral_Configuration Peripheral Configuration + * @brief Macros to configure clock source of different peripherals. + * @{ + */ + +#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6)\ + || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG) +/** @brief Macro to configure the USB clock. + * @param __USBCLKSOURCE__ specifies the USB clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_USBCLKSOURCE_PLL PLL clock divided by 1 selected as USB clock + * @arg @ref RCC_USBCLKSOURCE_PLL_DIV1_5 PLL clock divided by 1.5 selected as USB clock + */ +#define __HAL_RCC_USB_CONFIG(__USBCLKSOURCE__) \ + MODIFY_REG(RCC->CFGR, RCC_CFGR_USBPRE, (uint32_t)(__USBCLKSOURCE__)) + +/** @brief Macro to get the USB clock (USBCLK). + * @retval The clock source can be one of the following values: + * @arg @ref RCC_USBCLKSOURCE_PLL PLL clock divided by 1 selected as USB clock + * @arg @ref RCC_USBCLKSOURCE_PLL_DIV1_5 PLL clock divided by 1.5 selected as USB clock + */ +#define __HAL_RCC_GET_USB_SOURCE() ((uint32_t)(READ_BIT(RCC->CFGR, RCC_CFGR_USBPRE))) + +#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG */ + +#if defined(STM32F105xC) || defined(STM32F107xC) + +/** @brief Macro to configure the USB OTSclock. + * @param __USBCLKSOURCE__ specifies the USB clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_USBCLKSOURCE_PLL_DIV2 PLL clock divided by 2 selected as USB OTG FS clock + * @arg @ref RCC_USBCLKSOURCE_PLL_DIV3 PLL clock divided by 3 selected as USB OTG FS clock + */ +#define __HAL_RCC_USB_CONFIG(__USBCLKSOURCE__) \ + MODIFY_REG(RCC->CFGR, RCC_CFGR_OTGFSPRE, (uint32_t)(__USBCLKSOURCE__)) + +/** @brief Macro to get the USB clock (USBCLK). + * @retval The clock source can be one of the following values: + * @arg @ref RCC_USBCLKSOURCE_PLL_DIV2 PLL clock divided by 2 selected as USB OTG FS clock + * @arg @ref RCC_USBCLKSOURCE_PLL_DIV3 PLL clock divided by 3 selected as USB OTG FS clock + */ +#define __HAL_RCC_GET_USB_SOURCE() ((uint32_t)(READ_BIT(RCC->CFGR, RCC_CFGR_OTGFSPRE))) + +#endif /* STM32F105xC || STM32F107xC */ + +/** @brief Macro to configure the ADCx clock (x=1 to 3 depending on devices). + * @param __ADCCLKSOURCE__ specifies the ADC clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_ADCPCLK2_DIV2 PCLK2 clock divided by 2 selected as ADC clock + * @arg @ref RCC_ADCPCLK2_DIV4 PCLK2 clock divided by 4 selected as ADC clock + * @arg @ref RCC_ADCPCLK2_DIV6 PCLK2 clock divided by 6 selected as ADC clock + * @arg @ref RCC_ADCPCLK2_DIV8 PCLK2 clock divided by 8 selected as ADC clock + */ +#define __HAL_RCC_ADC_CONFIG(__ADCCLKSOURCE__) \ + MODIFY_REG(RCC->CFGR, RCC_CFGR_ADCPRE, (uint32_t)(__ADCCLKSOURCE__)) + +/** @brief Macro to get the ADC clock (ADCxCLK, x=1 to 3 depending on devices). + * @retval The clock source can be one of the following values: + * @arg @ref RCC_ADCPCLK2_DIV2 PCLK2 clock divided by 2 selected as ADC clock + * @arg @ref RCC_ADCPCLK2_DIV4 PCLK2 clock divided by 4 selected as ADC clock + * @arg @ref RCC_ADCPCLK2_DIV6 PCLK2 clock divided by 6 selected as ADC clock + * @arg @ref RCC_ADCPCLK2_DIV8 PCLK2 clock divided by 8 selected as ADC clock + */ +#define __HAL_RCC_GET_ADC_SOURCE() ((uint32_t)(READ_BIT(RCC->CFGR, RCC_CFGR_ADCPRE))) + +/** + * @} + */ + +#if defined(STM32F105xC) || defined(STM32F107xC) + +/** @addtogroup RCCEx_HSE_Configuration + * @{ + */ + +/** + * @brief Macro to configure the PLL2 & PLLI2S Predivision factor. + * @note Predivision factor can not be changed if PLL2 is used indirectly as system clock + * In this case, you have to select another source of the system clock, disable the PLL2 and PLLI2S and + * then change the PREDIV2 factor. + * @param __HSE_PREDIV2_VALUE__ specifies the PREDIV2 value applied to PLL2 & PLLI2S. + * This parameter must be a number between RCC_HSE_PREDIV2_DIV1 and RCC_HSE_PREDIV2_DIV16. + */ +#define __HAL_RCC_HSE_PREDIV2_CONFIG(__HSE_PREDIV2_VALUE__) \ + MODIFY_REG(RCC->CFGR2, RCC_CFGR2_PREDIV2, (uint32_t)(__HSE_PREDIV2_VALUE__)) + +/** + * @brief Macro to get prediv2 factor for PLL2 & PLL3. + */ +#define __HAL_RCC_HSE_GET_PREDIV2() READ_BIT(RCC->CFGR2, RCC_CFGR2_PREDIV2) + +/** + * @} + */ + +/** @addtogroup RCCEx_PLLI2S_Configuration + * @{ + */ + +/** @brief Macros to enable the main PLL2. + * @note After enabling the main PLL2, the application software should wait on + * PLL2RDY flag to be set indicating that PLL2 clock is stable and can + * be used as system clock source. + * @note The main PLL2 is disabled by hardware when entering STOP and STANDBY modes. + */ +#define __HAL_RCC_PLL2_ENABLE() (*(__IO uint32_t *) RCC_CR_PLL2ON_BB = ENABLE) + +/** @brief Macros to disable the main PLL2. + * @note The main PLL2 can not be disabled if it is used indirectly as system clock source + * @note The main PLL2 is disabled by hardware when entering STOP and STANDBY modes. + */ +#define __HAL_RCC_PLL2_DISABLE() (*(__IO uint32_t *) RCC_CR_PLL2ON_BB = DISABLE) + +/** @brief macros to configure the main PLL2 multiplication factor. + * @note This function must be used only when the main PLL2 is disabled. + * + * @param __PLL2MUL__ specifies the multiplication factor for PLL2 VCO output clock + * This parameter can be one of the following values: + * @arg @ref RCC_PLL2_MUL8 PLL2VCO = PLL2 clock entry x 8 + * @arg @ref RCC_PLL2_MUL9 PLL2VCO = PLL2 clock entry x 9 + * @arg @ref RCC_PLL2_MUL10 PLL2VCO = PLL2 clock entry x 10 + * @arg @ref RCC_PLL2_MUL11 PLL2VCO = PLL2 clock entry x 11 + * @arg @ref RCC_PLL2_MUL12 PLL2VCO = PLL2 clock entry x 12 + * @arg @ref RCC_PLL2_MUL13 PLL2VCO = PLL2 clock entry x 13 + * @arg @ref RCC_PLL2_MUL14 PLL2VCO = PLL2 clock entry x 14 + * @arg @ref RCC_PLL2_MUL16 PLL2VCO = PLL2 clock entry x 16 + * @arg @ref RCC_PLL2_MUL20 PLL2VCO = PLL2 clock entry x 20 + * + */ +#define __HAL_RCC_PLL2_CONFIG(__PLL2MUL__)\ + MODIFY_REG(RCC->CFGR2, RCC_CFGR2_PLL2MUL,(__PLL2MUL__)) + +/** + * @} + */ + +/** @defgroup RCCEx_I2S_Configuration I2S Configuration + * @brief Macros to configure clock source of I2S peripherals. + * @{ + */ + +/** @brief Macro to configure the I2S2 clock. + * @param __I2S2CLKSOURCE__ specifies the I2S2 clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_I2S2CLKSOURCE_SYSCLK system clock selected as I2S3 clock entry + * @arg @ref RCC_I2S2CLKSOURCE_PLLI2S_VCO PLLI2S VCO clock selected as I2S3 clock entry + */ +#define __HAL_RCC_I2S2_CONFIG(__I2S2CLKSOURCE__) \ + MODIFY_REG(RCC->CFGR2, RCC_CFGR2_I2S2SRC, (uint32_t)(__I2S2CLKSOURCE__)) + +/** @brief Macro to get the I2S2 clock (I2S2CLK). + * @retval The clock source can be one of the following values: + * @arg @ref RCC_I2S2CLKSOURCE_SYSCLK system clock selected as I2S3 clock entry + * @arg @ref RCC_I2S2CLKSOURCE_PLLI2S_VCO PLLI2S VCO clock selected as I2S3 clock entry + */ +#define __HAL_RCC_GET_I2S2_SOURCE() ((uint32_t)(READ_BIT(RCC->CFGR2, RCC_CFGR2_I2S2SRC))) + +/** @brief Macro to configure the I2S3 clock. + * @param __I2S2CLKSOURCE__ specifies the I2S3 clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_I2S3CLKSOURCE_SYSCLK system clock selected as I2S3 clock entry + * @arg @ref RCC_I2S3CLKSOURCE_PLLI2S_VCO PLLI2S VCO clock selected as I2S3 clock entry + */ +#define __HAL_RCC_I2S3_CONFIG(__I2S2CLKSOURCE__) \ + MODIFY_REG(RCC->CFGR2, RCC_CFGR2_I2S3SRC, (uint32_t)(__I2S2CLKSOURCE__)) + +/** @brief Macro to get the I2S3 clock (I2S3CLK). + * @retval The clock source can be one of the following values: + * @arg @ref RCC_I2S3CLKSOURCE_SYSCLK system clock selected as I2S3 clock entry + * @arg @ref RCC_I2S3CLKSOURCE_PLLI2S_VCO PLLI2S VCO clock selected as I2S3 clock entry + */ +#define __HAL_RCC_GET_I2S3_SOURCE() ((uint32_t)(READ_BIT(RCC->CFGR2, RCC_CFGR2_I2S3SRC))) + +/** + * @} + */ + +#endif /* STM32F105xC || STM32F107xC */ +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup RCCEx_Exported_Functions + * @{ + */ + +/** @addtogroup RCCEx_Exported_Functions_Group1 + * @{ + */ + +HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit); +void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit); +uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk); + +/** + * @} + */ + +#if defined(STM32F105xC) || defined(STM32F107xC) +/** @addtogroup RCCEx_Exported_Functions_Group2 + * @{ + */ +HAL_StatusTypeDef HAL_RCCEx_EnablePLLI2S(RCC_PLLI2SInitTypeDef* PLLI2SInit); +HAL_StatusTypeDef HAL_RCCEx_DisablePLLI2S(void); + +/** + * @} + */ + +/** @addtogroup RCCEx_Exported_Functions_Group3 + * @{ + */ +HAL_StatusTypeDef HAL_RCCEx_EnablePLL2(RCC_PLL2InitTypeDef* PLL2Init); +HAL_StatusTypeDef HAL_RCCEx_DisablePLL2(void); + +/** + * @} + */ +#endif /* STM32F105xC || STM32F107xC */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F1xx_HAL_RCC_EX_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ + diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_tim.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_tim.h new file mode 100644 index 00000000..6f177d1f --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_tim.h @@ -0,0 +1,2018 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_tim.h + * @author MCD Application Team + * @brief Header file of TIM HAL module. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef STM32F1xx_HAL_TIM_H +#define STM32F1xx_HAL_TIM_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal_def.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @addtogroup TIM + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ +/** @defgroup TIM_Exported_Types TIM Exported Types + * @{ + */ + +/** + * @brief TIM Time base Configuration Structure definition + */ +typedef struct +{ + uint32_t Prescaler; /*!< Specifies the prescaler value used to divide the TIM clock. + This parameter can be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF */ + + uint32_t CounterMode; /*!< Specifies the counter mode. + This parameter can be a value of @ref TIM_Counter_Mode */ + + uint32_t Period; /*!< Specifies the period value to be loaded into the active + Auto-Reload Register at the next update event. + This parameter can be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF. */ + + uint32_t ClockDivision; /*!< Specifies the clock division. + This parameter can be a value of @ref TIM_ClockDivision */ + + uint32_t RepetitionCounter; /*!< Specifies the repetition counter value. Each time the RCR downcounter + reaches zero, an update event is generated and counting restarts + from the RCR value (N). + This means in PWM mode that (N+1) corresponds to: + - the number of PWM periods in edge-aligned mode + - the number of half PWM period in center-aligned mode + GP timers: this parameter must be a number between Min_Data = 0x00 and Max_Data = 0xFF. + Advanced timers: this parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF. */ + + uint32_t AutoReloadPreload; /*!< Specifies the auto-reload preload. + This parameter can be a value of @ref TIM_AutoReloadPreload */ +} TIM_Base_InitTypeDef; + +/** + * @brief TIM Output Compare Configuration Structure definition + */ +typedef struct +{ + uint32_t OCMode; /*!< Specifies the TIM mode. + This parameter can be a value of @ref TIM_Output_Compare_and_PWM_modes */ + + uint32_t Pulse; /*!< Specifies the pulse value to be loaded into the Capture Compare Register. + This parameter can be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF */ + + uint32_t OCPolarity; /*!< Specifies the output polarity. + This parameter can be a value of @ref TIM_Output_Compare_Polarity */ + + uint32_t OCNPolarity; /*!< Specifies the complementary output polarity. + This parameter can be a value of @ref TIM_Output_Compare_N_Polarity + @note This parameter is valid only for timer instances supporting break feature. */ + + uint32_t OCFastMode; /*!< Specifies the Fast mode state. + This parameter can be a value of @ref TIM_Output_Fast_State + @note This parameter is valid only in PWM1 and PWM2 mode. */ + + + uint32_t OCIdleState; /*!< Specifies the TIM Output Compare pin state during Idle state. + This parameter can be a value of @ref TIM_Output_Compare_Idle_State + @note This parameter is valid only for timer instances supporting break feature. */ + + uint32_t OCNIdleState; /*!< Specifies the TIM Output Compare pin state during Idle state. + This parameter can be a value of @ref TIM_Output_Compare_N_Idle_State + @note This parameter is valid only for timer instances supporting break feature. */ +} TIM_OC_InitTypeDef; + +/** + * @brief TIM One Pulse Mode Configuration Structure definition + */ +typedef struct +{ + uint32_t OCMode; /*!< Specifies the TIM mode. + This parameter can be a value of @ref TIM_Output_Compare_and_PWM_modes */ + + uint32_t Pulse; /*!< Specifies the pulse value to be loaded into the Capture Compare Register. + This parameter can be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF */ + + uint32_t OCPolarity; /*!< Specifies the output polarity. + This parameter can be a value of @ref TIM_Output_Compare_Polarity */ + + uint32_t OCNPolarity; /*!< Specifies the complementary output polarity. + This parameter can be a value of @ref TIM_Output_Compare_N_Polarity + @note This parameter is valid only for timer instances supporting break feature. */ + + uint32_t OCIdleState; /*!< Specifies the TIM Output Compare pin state during Idle state. + This parameter can be a value of @ref TIM_Output_Compare_Idle_State + @note This parameter is valid only for timer instances supporting break feature. */ + + uint32_t OCNIdleState; /*!< Specifies the TIM Output Compare pin state during Idle state. + This parameter can be a value of @ref TIM_Output_Compare_N_Idle_State + @note This parameter is valid only for timer instances supporting break feature. */ + + uint32_t ICPolarity; /*!< Specifies the active edge of the input signal. + This parameter can be a value of @ref TIM_Input_Capture_Polarity */ + + uint32_t ICSelection; /*!< Specifies the input. + This parameter can be a value of @ref TIM_Input_Capture_Selection */ + + uint32_t ICFilter; /*!< Specifies the input capture filter. + This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ +} TIM_OnePulse_InitTypeDef; + +/** + * @brief TIM Input Capture Configuration Structure definition + */ +typedef struct +{ + uint32_t ICPolarity; /*!< Specifies the active edge of the input signal. + This parameter can be a value of @ref TIM_Input_Capture_Polarity */ + + uint32_t ICSelection; /*!< Specifies the input. + This parameter can be a value of @ref TIM_Input_Capture_Selection */ + + uint32_t ICPrescaler; /*!< Specifies the Input Capture Prescaler. + This parameter can be a value of @ref TIM_Input_Capture_Prescaler */ + + uint32_t ICFilter; /*!< Specifies the input capture filter. + This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ +} TIM_IC_InitTypeDef; + +/** + * @brief TIM Encoder Configuration Structure definition + */ +typedef struct +{ + uint32_t EncoderMode; /*!< Specifies the active edge of the input signal. + This parameter can be a value of @ref TIM_Encoder_Mode */ + + uint32_t IC1Polarity; /*!< Specifies the active edge of the input signal. + This parameter can be a value of @ref TIM_Input_Capture_Polarity */ + + uint32_t IC1Selection; /*!< Specifies the input. + This parameter can be a value of @ref TIM_Input_Capture_Selection */ + + uint32_t IC1Prescaler; /*!< Specifies the Input Capture Prescaler. + This parameter can be a value of @ref TIM_Input_Capture_Prescaler */ + + uint32_t IC1Filter; /*!< Specifies the input capture filter. + This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ + + uint32_t IC2Polarity; /*!< Specifies the active edge of the input signal. + This parameter can be a value of @ref TIM_Input_Capture_Polarity */ + + uint32_t IC2Selection; /*!< Specifies the input. + This parameter can be a value of @ref TIM_Input_Capture_Selection */ + + uint32_t IC2Prescaler; /*!< Specifies the Input Capture Prescaler. + This parameter can be a value of @ref TIM_Input_Capture_Prescaler */ + + uint32_t IC2Filter; /*!< Specifies the input capture filter. + This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ +} TIM_Encoder_InitTypeDef; + +/** + * @brief Clock Configuration Handle Structure definition + */ +typedef struct +{ + uint32_t ClockSource; /*!< TIM clock sources + This parameter can be a value of @ref TIM_Clock_Source */ + uint32_t ClockPolarity; /*!< TIM clock polarity + This parameter can be a value of @ref TIM_Clock_Polarity */ + uint32_t ClockPrescaler; /*!< TIM clock prescaler + This parameter can be a value of @ref TIM_Clock_Prescaler */ + uint32_t ClockFilter; /*!< TIM clock filter + This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ +} TIM_ClockConfigTypeDef; + +/** + * @brief TIM Clear Input Configuration Handle Structure definition + */ +typedef struct +{ + uint32_t ClearInputState; /*!< TIM clear Input state + This parameter can be ENABLE or DISABLE */ + uint32_t ClearInputSource; /*!< TIM clear Input sources + This parameter can be a value of @ref TIM_ClearInput_Source */ + uint32_t ClearInputPolarity; /*!< TIM Clear Input polarity + This parameter can be a value of @ref TIM_ClearInput_Polarity */ + uint32_t ClearInputPrescaler; /*!< TIM Clear Input prescaler + This parameter must be 0: When OCRef clear feature is used with ETR source, ETR prescaler must be off */ + uint32_t ClearInputFilter; /*!< TIM Clear Input filter + This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ +} TIM_ClearInputConfigTypeDef; + +/** + * @brief TIM Master configuration Structure definition + */ +typedef struct +{ + uint32_t MasterOutputTrigger; /*!< Trigger output (TRGO) selection + This parameter can be a value of @ref TIM_Master_Mode_Selection */ + uint32_t MasterSlaveMode; /*!< Master/slave mode selection + This parameter can be a value of @ref TIM_Master_Slave_Mode + @note When the Master/slave mode is enabled, the effect of + an event on the trigger input (TRGI) is delayed to allow a + perfect synchronization between the current timer and its + slaves (through TRGO). It is not mandatory in case of timer + synchronization mode. */ +} TIM_MasterConfigTypeDef; + +/** + * @brief TIM Slave configuration Structure definition + */ +typedef struct +{ + uint32_t SlaveMode; /*!< Slave mode selection + This parameter can be a value of @ref TIM_Slave_Mode */ + uint32_t InputTrigger; /*!< Input Trigger source + This parameter can be a value of @ref TIM_Trigger_Selection */ + uint32_t TriggerPolarity; /*!< Input Trigger polarity + This parameter can be a value of @ref TIM_Trigger_Polarity */ + uint32_t TriggerPrescaler; /*!< Input trigger prescaler + This parameter can be a value of @ref TIM_Trigger_Prescaler */ + uint32_t TriggerFilter; /*!< Input trigger filter + This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ + +} TIM_SlaveConfigTypeDef; + +/** + * @brief TIM Break input(s) and Dead time configuration Structure definition + * @note 2 break inputs can be configured (BKIN and BKIN2) with configurable + * filter and polarity. + */ +typedef struct +{ + uint32_t OffStateRunMode; /*!< TIM off state in run mode + This parameter can be a value of @ref TIM_OSSR_Off_State_Selection_for_Run_mode_state */ + uint32_t OffStateIDLEMode; /*!< TIM off state in IDLE mode + This parameter can be a value of @ref TIM_OSSI_Off_State_Selection_for_Idle_mode_state */ + uint32_t LockLevel; /*!< TIM Lock level + This parameter can be a value of @ref TIM_Lock_level */ + uint32_t DeadTime; /*!< TIM dead Time + This parameter can be a number between Min_Data = 0x00 and Max_Data = 0xFF */ + uint32_t BreakState; /*!< TIM Break State + This parameter can be a value of @ref TIM_Break_Input_enable_disable */ + uint32_t BreakPolarity; /*!< TIM Break input polarity + This parameter can be a value of @ref TIM_Break_Polarity */ + uint32_t BreakFilter; /*!< Specifies the break input filter. + This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ + uint32_t AutomaticOutput; /*!< TIM Automatic Output Enable state + This parameter can be a value of @ref TIM_AOE_Bit_Set_Reset */ +} TIM_BreakDeadTimeConfigTypeDef; + +/** + * @brief HAL State structures definition + */ +typedef enum +{ + HAL_TIM_STATE_RESET = 0x00U, /*!< Peripheral not yet initialized or disabled */ + HAL_TIM_STATE_READY = 0x01U, /*!< Peripheral Initialized and ready for use */ + HAL_TIM_STATE_BUSY = 0x02U, /*!< An internal process is ongoing */ + HAL_TIM_STATE_TIMEOUT = 0x03U, /*!< Timeout state */ + HAL_TIM_STATE_ERROR = 0x04U /*!< Reception process is ongoing */ +} HAL_TIM_StateTypeDef; + +/** + * @brief HAL Active channel structures definition + */ +typedef enum +{ + HAL_TIM_ACTIVE_CHANNEL_1 = 0x01U, /*!< The active channel is 1 */ + HAL_TIM_ACTIVE_CHANNEL_2 = 0x02U, /*!< The active channel is 2 */ + HAL_TIM_ACTIVE_CHANNEL_3 = 0x04U, /*!< The active channel is 3 */ + HAL_TIM_ACTIVE_CHANNEL_4 = 0x08U, /*!< The active channel is 4 */ + HAL_TIM_ACTIVE_CHANNEL_CLEARED = 0x00U /*!< All active channels cleared */ +} HAL_TIM_ActiveChannel; + +/** + * @brief TIM Time Base Handle Structure definition + */ +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) +typedef struct __TIM_HandleTypeDef +#else +typedef struct +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ +{ + TIM_TypeDef* Instance; /*!< Register base address */ + TIM_Base_InitTypeDef Init; /*!< TIM Time Base required parameters */ + HAL_TIM_ActiveChannel Channel; /*!< Active channel */ + DMA_HandleTypeDef* hdma[7]; /*!< DMA Handlers array + This array is accessed by a @ref DMA_Handle_index */ + HAL_LockTypeDef Lock; /*!< Locking object */ + __IO HAL_TIM_StateTypeDef State; /*!< TIM operation state */ + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + void (* Base_MspInitCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Base Msp Init Callback */ + void (* Base_MspDeInitCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Base Msp DeInit Callback */ + void (* IC_MspInitCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM IC Msp Init Callback */ + void (* IC_MspDeInitCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM IC Msp DeInit Callback */ + void (* OC_MspInitCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM OC Msp Init Callback */ + void (* OC_MspDeInitCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM OC Msp DeInit Callback */ + void (* PWM_MspInitCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM PWM Msp Init Callback */ + void (* PWM_MspDeInitCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM PWM Msp DeInit Callback */ + void (* OnePulse_MspInitCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM One Pulse Msp Init Callback */ + void (* OnePulse_MspDeInitCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM One Pulse Msp DeInit Callback */ + void (* Encoder_MspInitCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Encoder Msp Init Callback */ + void (* Encoder_MspDeInitCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Encoder Msp DeInit Callback */ + void (* HallSensor_MspInitCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Hall Sensor Msp Init Callback */ + void (* HallSensor_MspDeInitCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Hall Sensor Msp DeInit Callback */ + void (* PeriodElapsedCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Period Elapsed Callback */ + void (* PeriodElapsedHalfCpltCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Period Elapsed half complete Callback */ + void (* TriggerCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Trigger Callback */ + void (* TriggerHalfCpltCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Trigger half complete Callback */ + void (* IC_CaptureCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Input Capture Callback */ + void (* IC_CaptureHalfCpltCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Input Capture half complete Callback */ + void (* OC_DelayElapsedCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Output Compare Delay Elapsed Callback */ + void (* PWM_PulseFinishedCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM PWM Pulse Finished Callback */ + void (* PWM_PulseFinishedHalfCpltCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM PWM Pulse Finished half complete Callback */ + void (* ErrorCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Error Callback */ + void (* CommutationCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Commutation Callback */ + void (* CommutationHalfCpltCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Commutation half complete Callback */ + void (* BreakCallback)(struct __TIM_HandleTypeDef* htim); /*!< TIM Break Callback */ +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ +} TIM_HandleTypeDef; + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) +/** + * @brief HAL TIM Callback ID enumeration definition + */ +typedef enum +{ + HAL_TIM_BASE_MSPINIT_CB_ID = 0x00U /*!< TIM Base MspInit Callback ID */ + , HAL_TIM_BASE_MSPDEINIT_CB_ID = 0x01U /*!< TIM Base MspDeInit Callback ID */ + , HAL_TIM_IC_MSPINIT_CB_ID = 0x02U /*!< TIM IC MspInit Callback ID */ + , HAL_TIM_IC_MSPDEINIT_CB_ID = 0x03U /*!< TIM IC MspDeInit Callback ID */ + , HAL_TIM_OC_MSPINIT_CB_ID = 0x04U /*!< TIM OC MspInit Callback ID */ + , HAL_TIM_OC_MSPDEINIT_CB_ID = 0x05U /*!< TIM OC MspDeInit Callback ID */ + , HAL_TIM_PWM_MSPINIT_CB_ID = 0x06U /*!< TIM PWM MspInit Callback ID */ + , HAL_TIM_PWM_MSPDEINIT_CB_ID = 0x07U /*!< TIM PWM MspDeInit Callback ID */ + , HAL_TIM_ONE_PULSE_MSPINIT_CB_ID = 0x08U /*!< TIM One Pulse MspInit Callback ID */ + , HAL_TIM_ONE_PULSE_MSPDEINIT_CB_ID = 0x09U /*!< TIM One Pulse MspDeInit Callback ID */ + , HAL_TIM_ENCODER_MSPINIT_CB_ID = 0x0AU /*!< TIM Encoder MspInit Callback ID */ + , HAL_TIM_ENCODER_MSPDEINIT_CB_ID = 0x0BU /*!< TIM Encoder MspDeInit Callback ID */ + , HAL_TIM_HALL_SENSOR_MSPINIT_CB_ID = 0x0CU /*!< TIM Hall Sensor MspDeInit Callback ID */ + , HAL_TIM_HALL_SENSOR_MSPDEINIT_CB_ID = 0x0DU /*!< TIM Hall Sensor MspDeInit Callback ID */ + , HAL_TIM_PERIOD_ELAPSED_CB_ID = 0x0EU /*!< TIM Period Elapsed Callback ID */ + , HAL_TIM_PERIOD_ELAPSED_HALF_CB_ID = 0x0FU /*!< TIM Period Elapsed half complete Callback ID */ + , HAL_TIM_TRIGGER_CB_ID = 0x10U /*!< TIM Trigger Callback ID */ + , HAL_TIM_TRIGGER_HALF_CB_ID = 0x11U /*!< TIM Trigger half complete Callback ID */ + + , HAL_TIM_IC_CAPTURE_CB_ID = 0x12U /*!< TIM Input Capture Callback ID */ + , HAL_TIM_IC_CAPTURE_HALF_CB_ID = 0x13U /*!< TIM Input Capture half complete Callback ID */ + , HAL_TIM_OC_DELAY_ELAPSED_CB_ID = 0x14U /*!< TIM Output Compare Delay Elapsed Callback ID */ + , HAL_TIM_PWM_PULSE_FINISHED_CB_ID = 0x15U /*!< TIM PWM Pulse Finished Callback ID */ + , HAL_TIM_PWM_PULSE_FINISHED_HALF_CB_ID = 0x16U /*!< TIM PWM Pulse Finished half complete Callback ID */ + , HAL_TIM_ERROR_CB_ID = 0x17U /*!< TIM Error Callback ID */ + , HAL_TIM_COMMUTATION_CB_ID = 0x18U /*!< TIM Commutation Callback ID */ + , HAL_TIM_COMMUTATION_HALF_CB_ID = 0x19U /*!< TIM Commutation half complete Callback ID */ + , HAL_TIM_BREAK_CB_ID = 0x1AU /*!< TIM Break Callback ID */ +} HAL_TIM_CallbackIDTypeDef; + +/** + * @brief HAL TIM Callback pointer definition + */ +typedef void (*pTIM_CallbackTypeDef)(TIM_HandleTypeDef* htim); /*!< pointer to the TIM callback function */ + +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + +/** + * @} + */ +/* End of exported types -----------------------------------------------------*/ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup TIM_Exported_Constants TIM Exported Constants + * @{ + */ + +/** @defgroup TIM_ClearInput_Source TIM Clear Input Source + * @{ + */ +#define TIM_CLEARINPUTSOURCE_NONE 0x00000000U /*!< OCREF_CLR is disabled */ +#define TIM_CLEARINPUTSOURCE_ETR 0x00000001U /*!< OCREF_CLR is connected to ETRF input */ +/** + * @} + */ + +/** @defgroup TIM_DMA_Base_address TIM DMA Base Address + * @{ + */ +#define TIM_DMABASE_CR1 0x00000000U +#define TIM_DMABASE_CR2 0x00000001U +#define TIM_DMABASE_SMCR 0x00000002U +#define TIM_DMABASE_DIER 0x00000003U +#define TIM_DMABASE_SR 0x00000004U +#define TIM_DMABASE_EGR 0x00000005U +#define TIM_DMABASE_CCMR1 0x00000006U +#define TIM_DMABASE_CCMR2 0x00000007U +#define TIM_DMABASE_CCER 0x00000008U +#define TIM_DMABASE_CNT 0x00000009U +#define TIM_DMABASE_PSC 0x0000000AU +#define TIM_DMABASE_ARR 0x0000000BU +#define TIM_DMABASE_RCR 0x0000000CU +#define TIM_DMABASE_CCR1 0x0000000DU +#define TIM_DMABASE_CCR2 0x0000000EU +#define TIM_DMABASE_CCR3 0x0000000FU +#define TIM_DMABASE_CCR4 0x00000010U +#define TIM_DMABASE_BDTR 0x00000011U +#define TIM_DMABASE_DCR 0x00000012U +#define TIM_DMABASE_DMAR 0x00000013U +/** + * @} + */ + +/** @defgroup TIM_Event_Source TIM Event Source + * @{ + */ +#define TIM_EVENTSOURCE_UPDATE TIM_EGR_UG /*!< Reinitialize the counter and generates an update of the registers */ +#define TIM_EVENTSOURCE_CC1 TIM_EGR_CC1G /*!< A capture/compare event is generated on channel 1 */ +#define TIM_EVENTSOURCE_CC2 TIM_EGR_CC2G /*!< A capture/compare event is generated on channel 2 */ +#define TIM_EVENTSOURCE_CC3 TIM_EGR_CC3G /*!< A capture/compare event is generated on channel 3 */ +#define TIM_EVENTSOURCE_CC4 TIM_EGR_CC4G /*!< A capture/compare event is generated on channel 4 */ +#define TIM_EVENTSOURCE_COM TIM_EGR_COMG /*!< A commutation event is generated */ +#define TIM_EVENTSOURCE_TRIGGER TIM_EGR_TG /*!< A trigger event is generated */ +#define TIM_EVENTSOURCE_BREAK TIM_EGR_BG /*!< A break event is generated */ +/** + * @} + */ + +/** @defgroup TIM_Input_Channel_Polarity TIM Input Channel polarity + * @{ + */ +#define TIM_INPUTCHANNELPOLARITY_RISING 0x00000000U /*!< Polarity for TIx source */ +#define TIM_INPUTCHANNELPOLARITY_FALLING TIM_CCER_CC1P /*!< Polarity for TIx source */ +#define TIM_INPUTCHANNELPOLARITY_BOTHEDGE (TIM_CCER_CC1P | TIM_CCER_CC1NP) /*!< Polarity for TIx source */ +/** + * @} + */ + +/** @defgroup TIM_ETR_Polarity TIM ETR Polarity + * @{ + */ +#define TIM_ETRPOLARITY_INVERTED TIM_SMCR_ETP /*!< Polarity for ETR source */ +#define TIM_ETRPOLARITY_NONINVERTED 0x00000000U /*!< Polarity for ETR source */ +/** + * @} + */ + +/** @defgroup TIM_ETR_Prescaler TIM ETR Prescaler + * @{ + */ +#define TIM_ETRPRESCALER_DIV1 0x00000000U /*!< No prescaler is used */ +#define TIM_ETRPRESCALER_DIV2 TIM_SMCR_ETPS_0 /*!< ETR input source is divided by 2 */ +#define TIM_ETRPRESCALER_DIV4 TIM_SMCR_ETPS_1 /*!< ETR input source is divided by 4 */ +#define TIM_ETRPRESCALER_DIV8 TIM_SMCR_ETPS /*!< ETR input source is divided by 8 */ +/** + * @} + */ + +/** @defgroup TIM_Counter_Mode TIM Counter Mode + * @{ + */ +#define TIM_COUNTERMODE_UP 0x00000000U /*!< Counter used as up-counter */ +#define TIM_COUNTERMODE_DOWN TIM_CR1_DIR /*!< Counter used as down-counter */ +#define TIM_COUNTERMODE_CENTERALIGNED1 TIM_CR1_CMS_0 /*!< Center-aligned mode 1 */ +#define TIM_COUNTERMODE_CENTERALIGNED2 TIM_CR1_CMS_1 /*!< Center-aligned mode 2 */ +#define TIM_COUNTERMODE_CENTERALIGNED3 TIM_CR1_CMS /*!< Center-aligned mode 3 */ +/** + * @} + */ + +/** @defgroup TIM_ClockDivision TIM Clock Division + * @{ + */ +#define TIM_CLOCKDIVISION_DIV1 0x00000000U /*!< Clock division: tDTS=tCK_INT */ +#define TIM_CLOCKDIVISION_DIV2 TIM_CR1_CKD_0 /*!< Clock division: tDTS=2*tCK_INT */ +#define TIM_CLOCKDIVISION_DIV4 TIM_CR1_CKD_1 /*!< Clock division: tDTS=4*tCK_INT */ +/** + * @} + */ + +/** @defgroup TIM_Output_Compare_State TIM Output Compare State + * @{ + */ +#define TIM_OUTPUTSTATE_DISABLE 0x00000000U /*!< Capture/Compare 1 output disabled */ +#define TIM_OUTPUTSTATE_ENABLE TIM_CCER_CC1E /*!< Capture/Compare 1 output enabled */ +/** + * @} + */ + +/** @defgroup TIM_AutoReloadPreload TIM Auto-Reload Preload + * @{ + */ +#define TIM_AUTORELOAD_PRELOAD_DISABLE 0x00000000U /*!< TIMx_ARR register is not buffered */ +#define TIM_AUTORELOAD_PRELOAD_ENABLE TIM_CR1_ARPE /*!< TIMx_ARR register is buffered */ + +/** + * @} + */ + +/** @defgroup TIM_Output_Fast_State TIM Output Fast State + * @{ + */ +#define TIM_OCFAST_DISABLE 0x00000000U /*!< Output Compare fast disable */ +#define TIM_OCFAST_ENABLE TIM_CCMR1_OC1FE /*!< Output Compare fast enable */ +/** + * @} + */ + +/** @defgroup TIM_Output_Compare_N_State TIM Complementary Output Compare State + * @{ + */ +#define TIM_OUTPUTNSTATE_DISABLE 0x00000000U /*!< OCxN is disabled */ +#define TIM_OUTPUTNSTATE_ENABLE TIM_CCER_CC1NE /*!< OCxN is enabled */ +/** + * @} + */ + +/** @defgroup TIM_Output_Compare_Polarity TIM Output Compare Polarity + * @{ + */ +#define TIM_OCPOLARITY_HIGH 0x00000000U /*!< Capture/Compare output polarity */ +#define TIM_OCPOLARITY_LOW TIM_CCER_CC1P /*!< Capture/Compare output polarity */ +/** + * @} + */ + +/** @defgroup TIM_Output_Compare_N_Polarity TIM Complementary Output Compare Polarity + * @{ + */ +#define TIM_OCNPOLARITY_HIGH 0x00000000U /*!< Capture/Compare complementary output polarity */ +#define TIM_OCNPOLARITY_LOW TIM_CCER_CC1NP /*!< Capture/Compare complementary output polarity */ +/** + * @} + */ + +/** @defgroup TIM_Output_Compare_Idle_State TIM Output Compare Idle State + * @{ + */ +#define TIM_OCIDLESTATE_SET TIM_CR2_OIS1 /*!< Output Idle state: OCx=1 when MOE=0 */ +#define TIM_OCIDLESTATE_RESET 0x00000000U /*!< Output Idle state: OCx=0 when MOE=0 */ +/** + * @} + */ + +/** @defgroup TIM_Output_Compare_N_Idle_State TIM Complementary Output Compare Idle State + * @{ + */ +#define TIM_OCNIDLESTATE_SET TIM_CR2_OIS1N /*!< Complementary output Idle state: OCxN=1 when MOE=0 */ +#define TIM_OCNIDLESTATE_RESET 0x00000000U /*!< Complementary output Idle state: OCxN=0 when MOE=0 */ +/** + * @} + */ + +/** @defgroup TIM_Input_Capture_Polarity TIM Input Capture Polarity + * @{ + */ +#define TIM_ICPOLARITY_RISING TIM_INPUTCHANNELPOLARITY_RISING /*!< Capture triggered by rising edge on timer input */ +#define TIM_ICPOLARITY_FALLING TIM_INPUTCHANNELPOLARITY_FALLING /*!< Capture triggered by falling edge on timer input */ +#define TIM_ICPOLARITY_BOTHEDGE TIM_INPUTCHANNELPOLARITY_BOTHEDGE /*!< Capture triggered by both rising and falling edges on timer input*/ +/** + * @} + */ + +/** @defgroup TIM_Input_Capture_Selection TIM Input Capture Selection + * @{ + */ +#define TIM_ICSELECTION_DIRECTTI TIM_CCMR1_CC1S_0 /*!< TIM Input 1, 2, 3 or 4 is selected to be + connected to IC1, IC2, IC3 or IC4, respectively */ +#define TIM_ICSELECTION_INDIRECTTI TIM_CCMR1_CC1S_1 /*!< TIM Input 1, 2, 3 or 4 is selected to be + connected to IC2, IC1, IC4 or IC3, respectively */ +#define TIM_ICSELECTION_TRC TIM_CCMR1_CC1S /*!< TIM Input 1, 2, 3 or 4 is selected to be connected to TRC */ +/** + * @} + */ + +/** @defgroup TIM_Input_Capture_Prescaler TIM Input Capture Prescaler + * @{ + */ +#define TIM_ICPSC_DIV1 0x00000000U /*!< Capture performed each time an edge is detected on the capture input */ +#define TIM_ICPSC_DIV2 TIM_CCMR1_IC1PSC_0 /*!< Capture performed once every 2 events */ +#define TIM_ICPSC_DIV4 TIM_CCMR1_IC1PSC_1 /*!< Capture performed once every 4 events */ +#define TIM_ICPSC_DIV8 TIM_CCMR1_IC1PSC /*!< Capture performed once every 8 events */ +/** + * @} + */ + +/** @defgroup TIM_One_Pulse_Mode TIM One Pulse Mode + * @{ + */ +#define TIM_OPMODE_SINGLE TIM_CR1_OPM /*!< Counter stops counting at the next update event */ +#define TIM_OPMODE_REPETITIVE 0x00000000U /*!< Counter is not stopped at update event */ +/** + * @} + */ + +/** @defgroup TIM_Encoder_Mode TIM Encoder Mode + * @{ + */ +#define TIM_ENCODERMODE_TI1 TIM_SMCR_SMS_0 /*!< Quadrature encoder mode 1, x2 mode, counts up/down on TI1FP1 edge depending on TI2FP2 level */ +#define TIM_ENCODERMODE_TI2 TIM_SMCR_SMS_1 /*!< Quadrature encoder mode 2, x2 mode, counts up/down on TI2FP2 edge depending on TI1FP1 level. */ +#define TIM_ENCODERMODE_TI12 (TIM_SMCR_SMS_1 | TIM_SMCR_SMS_0) /*!< Quadrature encoder mode 3, x4 mode, counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input. */ +/** + * @} + */ + +/** @defgroup TIM_Interrupt_definition TIM interrupt Definition + * @{ + */ +#define TIM_IT_UPDATE TIM_DIER_UIE /*!< Update interrupt */ +#define TIM_IT_CC1 TIM_DIER_CC1IE /*!< Capture/Compare 1 interrupt */ +#define TIM_IT_CC2 TIM_DIER_CC2IE /*!< Capture/Compare 2 interrupt */ +#define TIM_IT_CC3 TIM_DIER_CC3IE /*!< Capture/Compare 3 interrupt */ +#define TIM_IT_CC4 TIM_DIER_CC4IE /*!< Capture/Compare 4 interrupt */ +#define TIM_IT_COM TIM_DIER_COMIE /*!< Commutation interrupt */ +#define TIM_IT_TRIGGER TIM_DIER_TIE /*!< Trigger interrupt */ +#define TIM_IT_BREAK TIM_DIER_BIE /*!< Break interrupt */ +/** + * @} + */ + +/** @defgroup TIM_Commutation_Source TIM Commutation Source + * @{ + */ +#define TIM_COMMUTATION_TRGI TIM_CR2_CCUS /*!< When Capture/compare control bits are preloaded, they are updated by setting the COMG bit or when an rising edge occurs on trigger input */ +#define TIM_COMMUTATION_SOFTWARE 0x00000000U /*!< When Capture/compare control bits are preloaded, they are updated by setting the COMG bit */ +/** + * @} + */ + +/** @defgroup TIM_DMA_sources TIM DMA Sources + * @{ + */ +#define TIM_DMA_UPDATE TIM_DIER_UDE /*!< DMA request is triggered by the update event */ +#define TIM_DMA_CC1 TIM_DIER_CC1DE /*!< DMA request is triggered by the capture/compare macth 1 event */ +#define TIM_DMA_CC2 TIM_DIER_CC2DE /*!< DMA request is triggered by the capture/compare macth 2 event event */ +#define TIM_DMA_CC3 TIM_DIER_CC3DE /*!< DMA request is triggered by the capture/compare macth 3 event event */ +#define TIM_DMA_CC4 TIM_DIER_CC4DE /*!< DMA request is triggered by the capture/compare macth 4 event event */ +#define TIM_DMA_COM TIM_DIER_COMDE /*!< DMA request is triggered by the commutation event */ +#define TIM_DMA_TRIGGER TIM_DIER_TDE /*!< DMA request is triggered by the trigger event */ +/** + * @} + */ + +/** @defgroup TIM_Flag_definition TIM Flag Definition + * @{ + */ +#define TIM_FLAG_UPDATE TIM_SR_UIF /*!< Update interrupt flag */ +#define TIM_FLAG_CC1 TIM_SR_CC1IF /*!< Capture/Compare 1 interrupt flag */ +#define TIM_FLAG_CC2 TIM_SR_CC2IF /*!< Capture/Compare 2 interrupt flag */ +#define TIM_FLAG_CC3 TIM_SR_CC3IF /*!< Capture/Compare 3 interrupt flag */ +#define TIM_FLAG_CC4 TIM_SR_CC4IF /*!< Capture/Compare 4 interrupt flag */ +#define TIM_FLAG_COM TIM_SR_COMIF /*!< Commutation interrupt flag */ +#define TIM_FLAG_TRIGGER TIM_SR_TIF /*!< Trigger interrupt flag */ +#define TIM_FLAG_BREAK TIM_SR_BIF /*!< Break interrupt flag */ +#define TIM_FLAG_CC1OF TIM_SR_CC1OF /*!< Capture 1 overcapture flag */ +#define TIM_FLAG_CC2OF TIM_SR_CC2OF /*!< Capture 2 overcapture flag */ +#define TIM_FLAG_CC3OF TIM_SR_CC3OF /*!< Capture 3 overcapture flag */ +#define TIM_FLAG_CC4OF TIM_SR_CC4OF /*!< Capture 4 overcapture flag */ +/** + * @} + */ + +/** @defgroup TIM_Channel TIM Channel + * @{ + */ +#define TIM_CHANNEL_1 0x00000000U /*!< Capture/compare channel 1 identifier */ +#define TIM_CHANNEL_2 0x00000004U /*!< Capture/compare channel 2 identifier */ +#define TIM_CHANNEL_3 0x00000008U /*!< Capture/compare channel 3 identifier */ +#define TIM_CHANNEL_4 0x0000000CU /*!< Capture/compare channel 4 identifier */ +#define TIM_CHANNEL_ALL 0x0000003CU /*!< Global Capture/compare channel identifier */ +/** + * @} + */ + +/** @defgroup TIM_Clock_Source TIM Clock Source + * @{ + */ +#define TIM_CLOCKSOURCE_ETRMODE2 TIM_SMCR_ETPS_1 /*!< External clock source mode 2 */ +#define TIM_CLOCKSOURCE_INTERNAL TIM_SMCR_ETPS_0 /*!< Internal clock source */ +#define TIM_CLOCKSOURCE_ITR0 TIM_TS_ITR0 /*!< External clock source mode 1 (ITR0) */ +#define TIM_CLOCKSOURCE_ITR1 TIM_TS_ITR1 /*!< External clock source mode 1 (ITR1) */ +#define TIM_CLOCKSOURCE_ITR2 TIM_TS_ITR2 /*!< External clock source mode 1 (ITR2) */ +#define TIM_CLOCKSOURCE_ITR3 TIM_TS_ITR3 /*!< External clock source mode 1 (ITR3) */ +#define TIM_CLOCKSOURCE_TI1ED TIM_TS_TI1F_ED /*!< External clock source mode 1 (TTI1FP1 + edge detect.) */ +#define TIM_CLOCKSOURCE_TI1 TIM_TS_TI1FP1 /*!< External clock source mode 1 (TTI1FP1) */ +#define TIM_CLOCKSOURCE_TI2 TIM_TS_TI2FP2 /*!< External clock source mode 1 (TTI2FP2) */ +#define TIM_CLOCKSOURCE_ETRMODE1 TIM_TS_ETRF /*!< External clock source mode 1 (ETRF) */ +/** + * @} + */ + +/** @defgroup TIM_Clock_Polarity TIM Clock Polarity + * @{ + */ +#define TIM_CLOCKPOLARITY_INVERTED TIM_ETRPOLARITY_INVERTED /*!< Polarity for ETRx clock sources */ +#define TIM_CLOCKPOLARITY_NONINVERTED TIM_ETRPOLARITY_NONINVERTED /*!< Polarity for ETRx clock sources */ +#define TIM_CLOCKPOLARITY_RISING TIM_INPUTCHANNELPOLARITY_RISING /*!< Polarity for TIx clock sources */ +#define TIM_CLOCKPOLARITY_FALLING TIM_INPUTCHANNELPOLARITY_FALLING /*!< Polarity for TIx clock sources */ +#define TIM_CLOCKPOLARITY_BOTHEDGE TIM_INPUTCHANNELPOLARITY_BOTHEDGE /*!< Polarity for TIx clock sources */ +/** + * @} + */ + +/** @defgroup TIM_Clock_Prescaler TIM Clock Prescaler + * @{ + */ +#define TIM_CLOCKPRESCALER_DIV1 TIM_ETRPRESCALER_DIV1 /*!< No prescaler is used */ +#define TIM_CLOCKPRESCALER_DIV2 TIM_ETRPRESCALER_DIV2 /*!< Prescaler for External ETR Clock: Capture performed once every 2 events. */ +#define TIM_CLOCKPRESCALER_DIV4 TIM_ETRPRESCALER_DIV4 /*!< Prescaler for External ETR Clock: Capture performed once every 4 events. */ +#define TIM_CLOCKPRESCALER_DIV8 TIM_ETRPRESCALER_DIV8 /*!< Prescaler for External ETR Clock: Capture performed once every 8 events. */ +/** + * @} + */ + +/** @defgroup TIM_ClearInput_Polarity TIM Clear Input Polarity + * @{ + */ +#define TIM_CLEARINPUTPOLARITY_INVERTED TIM_ETRPOLARITY_INVERTED /*!< Polarity for ETRx pin */ +#define TIM_CLEARINPUTPOLARITY_NONINVERTED TIM_ETRPOLARITY_NONINVERTED /*!< Polarity for ETRx pin */ +/** + * @} + */ + +/** @defgroup TIM_ClearInput_Prescaler TIM Clear Input Prescaler + * @{ + */ +#define TIM_CLEARINPUTPRESCALER_DIV1 TIM_ETRPRESCALER_DIV1 /*!< No prescaler is used */ +#define TIM_CLEARINPUTPRESCALER_DIV2 TIM_ETRPRESCALER_DIV2 /*!< Prescaler for External ETR pin: Capture performed once every 2 events. */ +#define TIM_CLEARINPUTPRESCALER_DIV4 TIM_ETRPRESCALER_DIV4 /*!< Prescaler for External ETR pin: Capture performed once every 4 events. */ +#define TIM_CLEARINPUTPRESCALER_DIV8 TIM_ETRPRESCALER_DIV8 /*!< Prescaler for External ETR pin: Capture performed once every 8 events. */ +/** + * @} + */ + +/** @defgroup TIM_OSSR_Off_State_Selection_for_Run_mode_state TIM OSSR OffState Selection for Run mode state + * @{ + */ +#define TIM_OSSR_ENABLE TIM_BDTR_OSSR /*!< When inactive, OC/OCN outputs are enabled (still controlled by the timer) */ +#define TIM_OSSR_DISABLE 0x00000000U /*!< When inactive, OC/OCN outputs are disabled (not controlled any longer by the timer) */ +/** + * @} + */ + +/** @defgroup TIM_OSSI_Off_State_Selection_for_Idle_mode_state TIM OSSI OffState Selection for Idle mode state + * @{ + */ +#define TIM_OSSI_ENABLE TIM_BDTR_OSSI /*!< When inactive, OC/OCN outputs are enabled (still controlled by the timer) */ +#define TIM_OSSI_DISABLE 0x00000000U /*!< When inactive, OC/OCN outputs are disabled (not controlled any longer by the timer) */ +/** + * @} + */ +/** @defgroup TIM_Lock_level TIM Lock level + * @{ + */ +#define TIM_LOCKLEVEL_OFF 0x00000000U /*!< LOCK OFF */ +#define TIM_LOCKLEVEL_1 TIM_BDTR_LOCK_0 /*!< LOCK Level 1 */ +#define TIM_LOCKLEVEL_2 TIM_BDTR_LOCK_1 /*!< LOCK Level 2 */ +#define TIM_LOCKLEVEL_3 TIM_BDTR_LOCK /*!< LOCK Level 3 */ +/** + * @} + */ + +/** @defgroup TIM_Break_Input_enable_disable TIM Break Input Enable + * @{ + */ +#define TIM_BREAK_ENABLE TIM_BDTR_BKE /*!< Break input BRK is enabled */ +#define TIM_BREAK_DISABLE 0x00000000U /*!< Break input BRK is disabled */ +/** + * @} + */ + +/** @defgroup TIM_Break_Polarity TIM Break Input Polarity + * @{ + */ +#define TIM_BREAKPOLARITY_LOW 0x00000000U /*!< Break input BRK is active low */ +#define TIM_BREAKPOLARITY_HIGH TIM_BDTR_BKP /*!< Break input BRK is active high */ +/** + * @} + */ + +/** @defgroup TIM_AOE_Bit_Set_Reset TIM Automatic Output Enable + * @{ + */ +#define TIM_AUTOMATICOUTPUT_DISABLE 0x00000000U /*!< MOE can be set only by software */ +#define TIM_AUTOMATICOUTPUT_ENABLE TIM_BDTR_AOE /*!< MOE can be set by software or automatically at the next update event + (if none of the break inputs BRK and BRK2 is active) */ +/** + * @} + */ + +/** @defgroup TIM_Master_Mode_Selection TIM Master Mode Selection + * @{ + */ +#define TIM_TRGO_RESET 0x00000000U /*!< TIMx_EGR.UG bit is used as trigger output (TRGO) */ +#define TIM_TRGO_ENABLE TIM_CR2_MMS_0 /*!< TIMx_CR1.CEN bit is used as trigger output (TRGO) */ +#define TIM_TRGO_UPDATE TIM_CR2_MMS_1 /*!< Update event is used as trigger output (TRGO) */ +#define TIM_TRGO_OC1 (TIM_CR2_MMS_1 | TIM_CR2_MMS_0) /*!< Capture or a compare match 1 is used as trigger output (TRGO) */ +#define TIM_TRGO_OC1REF TIM_CR2_MMS_2 /*!< OC1REF signal is used as trigger output (TRGO) */ +#define TIM_TRGO_OC2REF (TIM_CR2_MMS_2 | TIM_CR2_MMS_0) /*!< OC2REF signal is used as trigger output(TRGO) */ +#define TIM_TRGO_OC3REF (TIM_CR2_MMS_2 | TIM_CR2_MMS_1) /*!< OC3REF signal is used as trigger output(TRGO) */ +#define TIM_TRGO_OC4REF (TIM_CR2_MMS_2 | TIM_CR2_MMS_1 | TIM_CR2_MMS_0) /*!< OC4REF signal is used as trigger output(TRGO) */ +/** + * @} + */ + +/** @defgroup TIM_Master_Slave_Mode TIM Master/Slave Mode + * @{ + */ +#define TIM_MASTERSLAVEMODE_ENABLE TIM_SMCR_MSM /*!< No action */ +#define TIM_MASTERSLAVEMODE_DISABLE 0x00000000U /*!< Master/slave mode is selected */ +/** + * @} + */ + +/** @defgroup TIM_Slave_Mode TIM Slave mode + * @{ + */ +#define TIM_SLAVEMODE_DISABLE 0x00000000U /*!< Slave mode disabled */ +#define TIM_SLAVEMODE_RESET TIM_SMCR_SMS_2 /*!< Reset Mode */ +#define TIM_SLAVEMODE_GATED (TIM_SMCR_SMS_2 | TIM_SMCR_SMS_0) /*!< Gated Mode */ +#define TIM_SLAVEMODE_TRIGGER (TIM_SMCR_SMS_2 | TIM_SMCR_SMS_1) /*!< Trigger Mode */ +#define TIM_SLAVEMODE_EXTERNAL1 (TIM_SMCR_SMS_2 | TIM_SMCR_SMS_1 | TIM_SMCR_SMS_0) /*!< External Clock Mode 1 */ +/** + * @} + */ + +/** @defgroup TIM_Output_Compare_and_PWM_modes TIM Output Compare and PWM Modes + * @{ + */ +#define TIM_OCMODE_TIMING 0x00000000U /*!< Frozen */ +#define TIM_OCMODE_ACTIVE TIM_CCMR1_OC1M_0 /*!< Set channel to active level on match */ +#define TIM_OCMODE_INACTIVE TIM_CCMR1_OC1M_1 /*!< Set channel to inactive level on match */ +#define TIM_OCMODE_TOGGLE (TIM_CCMR1_OC1M_1 | TIM_CCMR1_OC1M_0) /*!< Toggle */ +#define TIM_OCMODE_PWM1 (TIM_CCMR1_OC1M_2 | TIM_CCMR1_OC1M_1) /*!< PWM mode 1 */ +#define TIM_OCMODE_PWM2 (TIM_CCMR1_OC1M_2 | TIM_CCMR1_OC1M_1 | TIM_CCMR1_OC1M_0) /*!< PWM mode 2 */ +#define TIM_OCMODE_FORCED_ACTIVE (TIM_CCMR1_OC1M_2 | TIM_CCMR1_OC1M_0) /*!< Force active level */ +#define TIM_OCMODE_FORCED_INACTIVE TIM_CCMR1_OC1M_2 /*!< Force inactive level */ +/** + * @} + */ + +/** @defgroup TIM_Trigger_Selection TIM Trigger Selection + * @{ + */ +#define TIM_TS_ITR0 0x00000000U /*!< Internal Trigger 0 (ITR0) */ +#define TIM_TS_ITR1 TIM_SMCR_TS_0 /*!< Internal Trigger 1 (ITR1) */ +#define TIM_TS_ITR2 TIM_SMCR_TS_1 /*!< Internal Trigger 2 (ITR2) */ +#define TIM_TS_ITR3 (TIM_SMCR_TS_0 | TIM_SMCR_TS_1) /*!< Internal Trigger 3 (ITR3) */ +#define TIM_TS_TI1F_ED TIM_SMCR_TS_2 /*!< TI1 Edge Detector (TI1F_ED) */ +#define TIM_TS_TI1FP1 (TIM_SMCR_TS_0 | TIM_SMCR_TS_2) /*!< Filtered Timer Input 1 (TI1FP1) */ +#define TIM_TS_TI2FP2 (TIM_SMCR_TS_1 | TIM_SMCR_TS_2) /*!< Filtered Timer Input 2 (TI2FP2) */ +#define TIM_TS_ETRF (TIM_SMCR_TS_0 | TIM_SMCR_TS_1 | TIM_SMCR_TS_2) /*!< Filtered External Trigger input (ETRF) */ +#define TIM_TS_NONE 0x0000FFFFU /*!< No trigger selected */ +/** + * @} + */ + +/** @defgroup TIM_Trigger_Polarity TIM Trigger Polarity + * @{ + */ +#define TIM_TRIGGERPOLARITY_INVERTED TIM_ETRPOLARITY_INVERTED /*!< Polarity for ETRx trigger sources */ +#define TIM_TRIGGERPOLARITY_NONINVERTED TIM_ETRPOLARITY_NONINVERTED /*!< Polarity for ETRx trigger sources */ +#define TIM_TRIGGERPOLARITY_RISING TIM_INPUTCHANNELPOLARITY_RISING /*!< Polarity for TIxFPx or TI1_ED trigger sources */ +#define TIM_TRIGGERPOLARITY_FALLING TIM_INPUTCHANNELPOLARITY_FALLING /*!< Polarity for TIxFPx or TI1_ED trigger sources */ +#define TIM_TRIGGERPOLARITY_BOTHEDGE TIM_INPUTCHANNELPOLARITY_BOTHEDGE /*!< Polarity for TIxFPx or TI1_ED trigger sources */ +/** + * @} + */ + +/** @defgroup TIM_Trigger_Prescaler TIM Trigger Prescaler + * @{ + */ +#define TIM_TRIGGERPRESCALER_DIV1 TIM_ETRPRESCALER_DIV1 /*!< No prescaler is used */ +#define TIM_TRIGGERPRESCALER_DIV2 TIM_ETRPRESCALER_DIV2 /*!< Prescaler for External ETR Trigger: Capture performed once every 2 events. */ +#define TIM_TRIGGERPRESCALER_DIV4 TIM_ETRPRESCALER_DIV4 /*!< Prescaler for External ETR Trigger: Capture performed once every 4 events. */ +#define TIM_TRIGGERPRESCALER_DIV8 TIM_ETRPRESCALER_DIV8 /*!< Prescaler for External ETR Trigger: Capture performed once every 8 events. */ +/** + * @} + */ + +/** @defgroup TIM_TI1_Selection TIM TI1 Input Selection + * @{ + */ +#define TIM_TI1SELECTION_CH1 0x00000000U /*!< The TIMx_CH1 pin is connected to TI1 input */ +#define TIM_TI1SELECTION_XORCOMBINATION TIM_CR2_TI1S /*!< The TIMx_CH1, CH2 and CH3 pins are connected to the TI1 input (XOR combination) */ +/** + * @} + */ + +/** @defgroup TIM_DMA_Burst_Length TIM DMA Burst Length + * @{ + */ +#define TIM_DMABURSTLENGTH_1TRANSFER 0x00000000U /*!< The transfer is done to 1 register starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_2TRANSFERS 0x00000100U /*!< The transfer is done to 2 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_3TRANSFERS 0x00000200U /*!< The transfer is done to 3 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_4TRANSFERS 0x00000300U /*!< The transfer is done to 4 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_5TRANSFERS 0x00000400U /*!< The transfer is done to 5 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_6TRANSFERS 0x00000500U /*!< The transfer is done to 6 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_7TRANSFERS 0x00000600U /*!< The transfer is done to 7 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_8TRANSFERS 0x00000700U /*!< The transfer is done to 8 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_9TRANSFERS 0x00000800U /*!< The transfer is done to 9 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_10TRANSFERS 0x00000900U /*!< The transfer is done to 10 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_11TRANSFERS 0x00000A00U /*!< The transfer is done to 11 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_12TRANSFERS 0x00000B00U /*!< The transfer is done to 12 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_13TRANSFERS 0x00000C00U /*!< The transfer is done to 13 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_14TRANSFERS 0x00000D00U /*!< The transfer is done to 14 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_15TRANSFERS 0x00000E00U /*!< The transfer is done to 15 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_16TRANSFERS 0x00000F00U /*!< The transfer is done to 16 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_17TRANSFERS 0x00001000U /*!< The transfer is done to 17 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +#define TIM_DMABURSTLENGTH_18TRANSFERS 0x00001100U /*!< The transfer is done to 18 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */ +/** + * @} + */ + +/** @defgroup DMA_Handle_index TIM DMA Handle Index + * @{ + */ +#define TIM_DMA_ID_UPDATE ((uint16_t) 0x0000) /*!< Index of the DMA handle used for Update DMA requests */ +#define TIM_DMA_ID_CC1 ((uint16_t) 0x0001) /*!< Index of the DMA handle used for Capture/Compare 1 DMA requests */ +#define TIM_DMA_ID_CC2 ((uint16_t) 0x0002) /*!< Index of the DMA handle used for Capture/Compare 2 DMA requests */ +#define TIM_DMA_ID_CC3 ((uint16_t) 0x0003) /*!< Index of the DMA handle used for Capture/Compare 3 DMA requests */ +#define TIM_DMA_ID_CC4 ((uint16_t) 0x0004) /*!< Index of the DMA handle used for Capture/Compare 4 DMA requests */ +#define TIM_DMA_ID_COMMUTATION ((uint16_t) 0x0005) /*!< Index of the DMA handle used for Commutation DMA requests */ +#define TIM_DMA_ID_TRIGGER ((uint16_t) 0x0006) /*!< Index of the DMA handle used for Trigger DMA requests */ +/** + * @} + */ + +/** @defgroup Channel_CC_State TIM Capture/Compare Channel State + * @{ + */ +#define TIM_CCx_ENABLE 0x00000001U /*!< Input or output channel is enabled */ +#define TIM_CCx_DISABLE 0x00000000U /*!< Input or output channel is disabled */ +#define TIM_CCxN_ENABLE 0x00000004U /*!< Complementary output channel is enabled */ +#define TIM_CCxN_DISABLE 0x00000000U /*!< Complementary output channel is enabled */ +/** + * @} + */ + +/** + * @} + */ +/* End of exported constants -------------------------------------------------*/ + +/* Exported macros -----------------------------------------------------------*/ +/** @defgroup TIM_Exported_Macros TIM Exported Macros + * @{ + */ + +/** @brief Reset TIM handle state. + * @param __HANDLE__ TIM handle. + * @retval None + */ +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) +#define __HAL_TIM_RESET_HANDLE_STATE(__HANDLE__) do { \ + (__HANDLE__)->State = HAL_TIM_STATE_RESET; \ + (__HANDLE__)->Base_MspInitCallback = NULL; \ + (__HANDLE__)->Base_MspDeInitCallback = NULL; \ + (__HANDLE__)->IC_MspInitCallback = NULL; \ + (__HANDLE__)->IC_MspDeInitCallback = NULL; \ + (__HANDLE__)->OC_MspInitCallback = NULL; \ + (__HANDLE__)->OC_MspDeInitCallback = NULL; \ + (__HANDLE__)->PWM_MspInitCallback = NULL; \ + (__HANDLE__)->PWM_MspDeInitCallback = NULL; \ + (__HANDLE__)->OnePulse_MspInitCallback = NULL; \ + (__HANDLE__)->OnePulse_MspDeInitCallback = NULL; \ + (__HANDLE__)->Encoder_MspInitCallback = NULL; \ + (__HANDLE__)->Encoder_MspDeInitCallback = NULL; \ + (__HANDLE__)->HallSensor_MspInitCallback = NULL; \ + (__HANDLE__)->HallSensor_MspDeInitCallback = NULL; \ + } while(0) +#else +#define __HAL_TIM_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_TIM_STATE_RESET) +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + +/** + * @brief Enable the TIM peripheral. + * @param __HANDLE__ TIM handle + * @retval None + */ +#define __HAL_TIM_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1|=(TIM_CR1_CEN)) + +/** + * @brief Enable the TIM main Output. + * @param __HANDLE__ TIM handle + * @retval None + */ +#define __HAL_TIM_MOE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->BDTR|=(TIM_BDTR_MOE)) + +/** + * @brief Disable the TIM peripheral. + * @param __HANDLE__ TIM handle + * @retval None + */ +#define __HAL_TIM_DISABLE(__HANDLE__) \ + do { \ + if (((__HANDLE__)->Instance->CCER & TIM_CCER_CCxE_MASK) == 0UL) \ + { \ + if(((__HANDLE__)->Instance->CCER & TIM_CCER_CCxNE_MASK) == 0UL) \ + { \ + (__HANDLE__)->Instance->CR1 &= ~(TIM_CR1_CEN); \ + } \ + } \ + } while(0) + +/** + * @brief Disable the TIM main Output. + * @param __HANDLE__ TIM handle + * @retval None + * @note The Main Output Enable of a timer instance is disabled only if all the CCx and CCxN channels have been disabled + */ +#define __HAL_TIM_MOE_DISABLE(__HANDLE__) \ + do { \ + if (((__HANDLE__)->Instance->CCER & TIM_CCER_CCxE_MASK) == 0UL) \ + { \ + if(((__HANDLE__)->Instance->CCER & TIM_CCER_CCxNE_MASK) == 0UL) \ + { \ + (__HANDLE__)->Instance->BDTR &= ~(TIM_BDTR_MOE); \ + } \ + } \ + } while(0) + +/** + * @brief Disable the TIM main Output. + * @param __HANDLE__ TIM handle + * @retval None + * @note The Main Output Enable of a timer instance is disabled unconditionally + */ +#define __HAL_TIM_MOE_DISABLE_UNCONDITIONALLY(__HANDLE__) (__HANDLE__)->Instance->BDTR &= ~(TIM_BDTR_MOE) + +/** @brief Enable the specified TIM interrupt. + * @param __HANDLE__ specifies the TIM Handle. + * @param __INTERRUPT__ specifies the TIM interrupt source to enable. + * This parameter can be one of the following values: + * @arg TIM_IT_UPDATE: Update interrupt + * @arg TIM_IT_CC1: Capture/Compare 1 interrupt + * @arg TIM_IT_CC2: Capture/Compare 2 interrupt + * @arg TIM_IT_CC3: Capture/Compare 3 interrupt + * @arg TIM_IT_CC4: Capture/Compare 4 interrupt + * @arg TIM_IT_COM: Commutation interrupt + * @arg TIM_IT_TRIGGER: Trigger interrupt + * @arg TIM_IT_BREAK: Break interrupt + * @retval None + */ +#define __HAL_TIM_ENABLE_IT(__HANDLE__, __INTERRUPT__) ((__HANDLE__)->Instance->DIER |= (__INTERRUPT__)) + +/** @brief Disable the specified TIM interrupt. + * @param __HANDLE__ specifies the TIM Handle. + * @param __INTERRUPT__ specifies the TIM interrupt source to disable. + * This parameter can be one of the following values: + * @arg TIM_IT_UPDATE: Update interrupt + * @arg TIM_IT_CC1: Capture/Compare 1 interrupt + * @arg TIM_IT_CC2: Capture/Compare 2 interrupt + * @arg TIM_IT_CC3: Capture/Compare 3 interrupt + * @arg TIM_IT_CC4: Capture/Compare 4 interrupt + * @arg TIM_IT_COM: Commutation interrupt + * @arg TIM_IT_TRIGGER: Trigger interrupt + * @arg TIM_IT_BREAK: Break interrupt + * @retval None + */ +#define __HAL_TIM_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((__HANDLE__)->Instance->DIER &= ~(__INTERRUPT__)) + +/** @brief Enable the specified DMA request. + * @param __HANDLE__ specifies the TIM Handle. + * @param __DMA__ specifies the TIM DMA request to enable. + * This parameter can be one of the following values: + * @arg TIM_DMA_UPDATE: Update DMA request + * @arg TIM_DMA_CC1: Capture/Compare 1 DMA request + * @arg TIM_DMA_CC2: Capture/Compare 2 DMA request + * @arg TIM_DMA_CC3: Capture/Compare 3 DMA request + * @arg TIM_DMA_CC4: Capture/Compare 4 DMA request + * @arg TIM_DMA_COM: Commutation DMA request + * @arg TIM_DMA_TRIGGER: Trigger DMA request + * @retval None + */ +#define __HAL_TIM_ENABLE_DMA(__HANDLE__, __DMA__) ((__HANDLE__)->Instance->DIER |= (__DMA__)) + +/** @brief Disable the specified DMA request. + * @param __HANDLE__ specifies the TIM Handle. + * @param __DMA__ specifies the TIM DMA request to disable. + * This parameter can be one of the following values: + * @arg TIM_DMA_UPDATE: Update DMA request + * @arg TIM_DMA_CC1: Capture/Compare 1 DMA request + * @arg TIM_DMA_CC2: Capture/Compare 2 DMA request + * @arg TIM_DMA_CC3: Capture/Compare 3 DMA request + * @arg TIM_DMA_CC4: Capture/Compare 4 DMA request + * @arg TIM_DMA_COM: Commutation DMA request + * @arg TIM_DMA_TRIGGER: Trigger DMA request + * @retval None + */ +#define __HAL_TIM_DISABLE_DMA(__HANDLE__, __DMA__) ((__HANDLE__)->Instance->DIER &= ~(__DMA__)) + +/** @brief Check whether the specified TIM interrupt flag is set or not. + * @param __HANDLE__ specifies the TIM Handle. + * @param __FLAG__ specifies the TIM interrupt flag to check. + * This parameter can be one of the following values: + * @arg TIM_FLAG_UPDATE: Update interrupt flag + * @arg TIM_FLAG_CC1: Capture/Compare 1 interrupt flag + * @arg TIM_FLAG_CC2: Capture/Compare 2 interrupt flag + * @arg TIM_FLAG_CC3: Capture/Compare 3 interrupt flag + * @arg TIM_FLAG_CC4: Capture/Compare 4 interrupt flag + * @arg TIM_FLAG_COM: Commutation interrupt flag + * @arg TIM_FLAG_TRIGGER: Trigger interrupt flag + * @arg TIM_FLAG_BREAK: Break interrupt flag + * @arg TIM_FLAG_CC1OF: Capture/Compare 1 overcapture flag + * @arg TIM_FLAG_CC2OF: Capture/Compare 2 overcapture flag + * @arg TIM_FLAG_CC3OF: Capture/Compare 3 overcapture flag + * @arg TIM_FLAG_CC4OF: Capture/Compare 4 overcapture flag + * @retval The new state of __FLAG__ (TRUE or FALSE). + */ +#define __HAL_TIM_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR &(__FLAG__)) == (__FLAG__)) + +/** @brief Clear the specified TIM interrupt flag. + * @param __HANDLE__ specifies the TIM Handle. + * @param __FLAG__ specifies the TIM interrupt flag to clear. + * This parameter can be one of the following values: + * @arg TIM_FLAG_UPDATE: Update interrupt flag + * @arg TIM_FLAG_CC1: Capture/Compare 1 interrupt flag + * @arg TIM_FLAG_CC2: Capture/Compare 2 interrupt flag + * @arg TIM_FLAG_CC3: Capture/Compare 3 interrupt flag + * @arg TIM_FLAG_CC4: Capture/Compare 4 interrupt flag + * @arg TIM_FLAG_COM: Commutation interrupt flag + * @arg TIM_FLAG_TRIGGER: Trigger interrupt flag + * @arg TIM_FLAG_BREAK: Break interrupt flag + * @arg TIM_FLAG_CC1OF: Capture/Compare 1 overcapture flag + * @arg TIM_FLAG_CC2OF: Capture/Compare 2 overcapture flag + * @arg TIM_FLAG_CC3OF: Capture/Compare 3 overcapture flag + * @arg TIM_FLAG_CC4OF: Capture/Compare 4 overcapture flag + * @retval The new state of __FLAG__ (TRUE or FALSE). + */ +#define __HAL_TIM_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->SR = ~(__FLAG__)) + +/** + * @brief Check whether the specified TIM interrupt source is enabled or not. + * @param __HANDLE__ TIM handle + * @param __INTERRUPT__ specifies the TIM interrupt source to check. + * This parameter can be one of the following values: + * @arg TIM_IT_UPDATE: Update interrupt + * @arg TIM_IT_CC1: Capture/Compare 1 interrupt + * @arg TIM_IT_CC2: Capture/Compare 2 interrupt + * @arg TIM_IT_CC3: Capture/Compare 3 interrupt + * @arg TIM_IT_CC4: Capture/Compare 4 interrupt + * @arg TIM_IT_COM: Commutation interrupt + * @arg TIM_IT_TRIGGER: Trigger interrupt + * @arg TIM_IT_BREAK: Break interrupt + * @retval The state of TIM_IT (SET or RESET). + */ +#define __HAL_TIM_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->DIER & (__INTERRUPT__)) \ + == (__INTERRUPT__)) ? SET : RESET) + +/** @brief Clear the TIM interrupt pending bits. + * @param __HANDLE__ TIM handle + * @param __INTERRUPT__ specifies the interrupt pending bit to clear. + * This parameter can be one of the following values: + * @arg TIM_IT_UPDATE: Update interrupt + * @arg TIM_IT_CC1: Capture/Compare 1 interrupt + * @arg TIM_IT_CC2: Capture/Compare 2 interrupt + * @arg TIM_IT_CC3: Capture/Compare 3 interrupt + * @arg TIM_IT_CC4: Capture/Compare 4 interrupt + * @arg TIM_IT_COM: Commutation interrupt + * @arg TIM_IT_TRIGGER: Trigger interrupt + * @arg TIM_IT_BREAK: Break interrupt + * @retval None + */ +#define __HAL_TIM_CLEAR_IT(__HANDLE__, __INTERRUPT__) ((__HANDLE__)->Instance->SR = ~(__INTERRUPT__)) + +/** + * @brief Indicates whether or not the TIM Counter is used as downcounter. + * @param __HANDLE__ TIM handle. + * @retval False (Counter used as upcounter) or True (Counter used as downcounter) + * @note This macro is particularly useful to get the counting mode when the timer operates in Center-aligned mode or Encoder +mode. + */ +#define __HAL_TIM_IS_TIM_COUNTING_DOWN(__HANDLE__) (((__HANDLE__)->Instance->CR1 &(TIM_CR1_DIR)) == (TIM_CR1_DIR)) + +/** + * @brief Set the TIM Prescaler on runtime. + * @param __HANDLE__ TIM handle. + * @param __PRESC__ specifies the Prescaler new value. + * @retval None + */ +#define __HAL_TIM_SET_PRESCALER(__HANDLE__, __PRESC__) ((__HANDLE__)->Instance->PSC = (__PRESC__)) + +/** + * @brief Set the TIM Counter Register value on runtime. + * @param __HANDLE__ TIM handle. + * @param __COUNTER__ specifies the Counter register new value. + * @retval None + */ +#define __HAL_TIM_SET_COUNTER(__HANDLE__, __COUNTER__) ((__HANDLE__)->Instance->CNT = (__COUNTER__)) + +/** + * @brief Get the TIM Counter Register value on runtime. + * @param __HANDLE__ TIM handle. + * @retval 16-bit or 32-bit value of the timer counter register (TIMx_CNT) + */ +#define __HAL_TIM_GET_COUNTER(__HANDLE__) ((__HANDLE__)->Instance->CNT) + +/** + * @brief Set the TIM Autoreload Register value on runtime without calling another time any Init function. + * @param __HANDLE__ TIM handle. + * @param __AUTORELOAD__ specifies the Counter register new value. + * @retval None + */ +#define __HAL_TIM_SET_AUTORELOAD(__HANDLE__, __AUTORELOAD__) \ + do{ \ + (__HANDLE__)->Instance->ARR = (__AUTORELOAD__); \ + (__HANDLE__)->Init.Period = (__AUTORELOAD__); \ + } while(0) + +/** + * @brief Get the TIM Autoreload Register value on runtime. + * @param __HANDLE__ TIM handle. + * @retval 16-bit or 32-bit value of the timer auto-reload register(TIMx_ARR) + */ +#define __HAL_TIM_GET_AUTORELOAD(__HANDLE__) ((__HANDLE__)->Instance->ARR) + +/** + * @brief Set the TIM Clock Division value on runtime without calling another time any Init function. + * @param __HANDLE__ TIM handle. + * @param __CKD__ specifies the clock division value. + * This parameter can be one of the following value: + * @arg TIM_CLOCKDIVISION_DIV1: tDTS=tCK_INT + * @arg TIM_CLOCKDIVISION_DIV2: tDTS=2*tCK_INT + * @arg TIM_CLOCKDIVISION_DIV4: tDTS=4*tCK_INT + * @retval None + */ +#define __HAL_TIM_SET_CLOCKDIVISION(__HANDLE__, __CKD__) \ + do{ \ + (__HANDLE__)->Instance->CR1 &= (~TIM_CR1_CKD); \ + (__HANDLE__)->Instance->CR1 |= (__CKD__); \ + (__HANDLE__)->Init.ClockDivision = (__CKD__); \ + } while(0) + +/** + * @brief Get the TIM Clock Division value on runtime. + * @param __HANDLE__ TIM handle. + * @retval The clock division can be one of the following values: + * @arg TIM_CLOCKDIVISION_DIV1: tDTS=tCK_INT + * @arg TIM_CLOCKDIVISION_DIV2: tDTS=2*tCK_INT + * @arg TIM_CLOCKDIVISION_DIV4: tDTS=4*tCK_INT + */ +#define __HAL_TIM_GET_CLOCKDIVISION(__HANDLE__) ((__HANDLE__)->Instance->CR1 & TIM_CR1_CKD) + +/** + * @brief Set the TIM Input Capture prescaler on runtime without calling another time HAL_TIM_IC_ConfigChannel() function. + * @param __HANDLE__ TIM handle. + * @param __CHANNEL__ TIM Channels to be configured. + * This parameter can be one of the following values: + * @arg TIM_CHANNEL_1: TIM Channel 1 selected + * @arg TIM_CHANNEL_2: TIM Channel 2 selected + * @arg TIM_CHANNEL_3: TIM Channel 3 selected + * @arg TIM_CHANNEL_4: TIM Channel 4 selected + * @param __ICPSC__ specifies the Input Capture4 prescaler new value. + * This parameter can be one of the following values: + * @arg TIM_ICPSC_DIV1: no prescaler + * @arg TIM_ICPSC_DIV2: capture is done once every 2 events + * @arg TIM_ICPSC_DIV4: capture is done once every 4 events + * @arg TIM_ICPSC_DIV8: capture is done once every 8 events + * @retval None + */ +#define __HAL_TIM_SET_ICPRESCALER(__HANDLE__, __CHANNEL__, __ICPSC__) \ + do{ \ + TIM_RESET_ICPRESCALERVALUE((__HANDLE__), (__CHANNEL__)); \ + TIM_SET_ICPRESCALERVALUE((__HANDLE__), (__CHANNEL__), (__ICPSC__)); \ + } while(0) + +/** + * @brief Get the TIM Input Capture prescaler on runtime. + * @param __HANDLE__ TIM handle. + * @param __CHANNEL__ TIM Channels to be configured. + * This parameter can be one of the following values: + * @arg TIM_CHANNEL_1: get input capture 1 prescaler value + * @arg TIM_CHANNEL_2: get input capture 2 prescaler value + * @arg TIM_CHANNEL_3: get input capture 3 prescaler value + * @arg TIM_CHANNEL_4: get input capture 4 prescaler value + * @retval The input capture prescaler can be one of the following values: + * @arg TIM_ICPSC_DIV1: no prescaler + * @arg TIM_ICPSC_DIV2: capture is done once every 2 events + * @arg TIM_ICPSC_DIV4: capture is done once every 4 events + * @arg TIM_ICPSC_DIV8: capture is done once every 8 events + */ +#define __HAL_TIM_GET_ICPRESCALER(__HANDLE__, __CHANNEL__) \ + (((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCMR1 & TIM_CCMR1_IC1PSC) :\ + ((__CHANNEL__) == TIM_CHANNEL_2) ? (((__HANDLE__)->Instance->CCMR1 & TIM_CCMR1_IC2PSC) >> 8U) :\ + ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCMR2 & TIM_CCMR2_IC3PSC) :\ + (((__HANDLE__)->Instance->CCMR2 & TIM_CCMR2_IC4PSC)) >> 8U) + +/** + * @brief Set the TIM Capture Compare Register value on runtime without calling another time ConfigChannel function. + * @param __HANDLE__ TIM handle. + * @param __CHANNEL__ TIM Channels to be configured. + * This parameter can be one of the following values: + * @arg TIM_CHANNEL_1: TIM Channel 1 selected + * @arg TIM_CHANNEL_2: TIM Channel 2 selected + * @arg TIM_CHANNEL_3: TIM Channel 3 selected + * @arg TIM_CHANNEL_4: TIM Channel 4 selected + * @param __COMPARE__ specifies the Capture Compare register new value. + * @retval None + */ +#define __HAL_TIM_SET_COMPARE(__HANDLE__, __CHANNEL__, __COMPARE__) \ + (((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCR1 = (__COMPARE__)) :\ + ((__CHANNEL__) == TIM_CHANNEL_2) ? ((__HANDLE__)->Instance->CCR2 = (__COMPARE__)) :\ + ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCR3 = (__COMPARE__)) :\ + ((__HANDLE__)->Instance->CCR4 = (__COMPARE__))) + +/** + * @brief Get the TIM Capture Compare Register value on runtime. + * @param __HANDLE__ TIM handle. + * @param __CHANNEL__ TIM Channel associated with the capture compare register + * This parameter can be one of the following values: + * @arg TIM_CHANNEL_1: get capture/compare 1 register value + * @arg TIM_CHANNEL_2: get capture/compare 2 register value + * @arg TIM_CHANNEL_3: get capture/compare 3 register value + * @arg TIM_CHANNEL_4: get capture/compare 4 register value + * @retval 16-bit or 32-bit value of the capture/compare register (TIMx_CCRy) + */ +#define __HAL_TIM_GET_COMPARE(__HANDLE__, __CHANNEL__) \ + (((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCR1) :\ + ((__CHANNEL__) == TIM_CHANNEL_2) ? ((__HANDLE__)->Instance->CCR2) :\ + ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCR3) :\ + ((__HANDLE__)->Instance->CCR4)) + +/** + * @brief Set the TIM Output compare preload. + * @param __HANDLE__ TIM handle. + * @param __CHANNEL__ TIM Channels to be configured. + * This parameter can be one of the following values: + * @arg TIM_CHANNEL_1: TIM Channel 1 selected + * @arg TIM_CHANNEL_2: TIM Channel 2 selected + * @arg TIM_CHANNEL_3: TIM Channel 3 selected + * @arg TIM_CHANNEL_4: TIM Channel 4 selected + * @retval None + */ +#define __HAL_TIM_ENABLE_OCxPRELOAD(__HANDLE__, __CHANNEL__) \ + (((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCMR1 |= TIM_CCMR1_OC1PE) :\ + ((__CHANNEL__) == TIM_CHANNEL_2) ? ((__HANDLE__)->Instance->CCMR1 |= TIM_CCMR1_OC2PE) :\ + ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCMR2 |= TIM_CCMR2_OC3PE) :\ + ((__HANDLE__)->Instance->CCMR2 |= TIM_CCMR2_OC4PE)) + +/** + * @brief Reset the TIM Output compare preload. + * @param __HANDLE__ TIM handle. + * @param __CHANNEL__ TIM Channels to be configured. + * This parameter can be one of the following values: + * @arg TIM_CHANNEL_1: TIM Channel 1 selected + * @arg TIM_CHANNEL_2: TIM Channel 2 selected + * @arg TIM_CHANNEL_3: TIM Channel 3 selected + * @arg TIM_CHANNEL_4: TIM Channel 4 selected + * @retval None + */ +#define __HAL_TIM_DISABLE_OCxPRELOAD(__HANDLE__, __CHANNEL__) \ + (((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCMR1 &= ~TIM_CCMR1_OC1PE) :\ + ((__CHANNEL__) == TIM_CHANNEL_2) ? ((__HANDLE__)->Instance->CCMR1 &= ~TIM_CCMR1_OC2PE) :\ + ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCMR2 &= ~TIM_CCMR2_OC3PE) :\ + ((__HANDLE__)->Instance->CCMR2 &= ~TIM_CCMR2_OC4PE)) + +/** + * @brief Enable fast mode for a given channel. + * @param __HANDLE__ TIM handle. + * @param __CHANNEL__ TIM Channels to be configured. + * This parameter can be one of the following values: + * @arg TIM_CHANNEL_1: TIM Channel 1 selected + * @arg TIM_CHANNEL_2: TIM Channel 2 selected + * @arg TIM_CHANNEL_3: TIM Channel 3 selected + * @arg TIM_CHANNEL_4: TIM Channel 4 selected + * @note When fast mode is enabled an active edge on the trigger input acts + * like a compare match on CCx output. Delay to sample the trigger + * input and to activate CCx output is reduced to 3 clock cycles. + * @note Fast mode acts only if the channel is configured in PWM1 or PWM2 mode. + * @retval None + */ +#define __HAL_TIM_ENABLE_OCxFAST(__HANDLE__, __CHANNEL__) \ + (((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCMR1 |= TIM_CCMR1_OC1FE) :\ + ((__CHANNEL__) == TIM_CHANNEL_2) ? ((__HANDLE__)->Instance->CCMR1 |= TIM_CCMR1_OC2FE) :\ + ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCMR2 |= TIM_CCMR2_OC3FE) :\ + ((__HANDLE__)->Instance->CCMR2 |= TIM_CCMR2_OC4FE)) + +/** + * @brief Disable fast mode for a given channel. + * @param __HANDLE__ TIM handle. + * @param __CHANNEL__ TIM Channels to be configured. + * This parameter can be one of the following values: + * @arg TIM_CHANNEL_1: TIM Channel 1 selected + * @arg TIM_CHANNEL_2: TIM Channel 2 selected + * @arg TIM_CHANNEL_3: TIM Channel 3 selected + * @arg TIM_CHANNEL_4: TIM Channel 4 selected + * @note When fast mode is disabled CCx output behaves normally depending + * on counter and CCRx values even when the trigger is ON. The minimum + * delay to activate CCx output when an active edge occurs on the + * trigger input is 5 clock cycles. + * @retval None + */ +#define __HAL_TIM_DISABLE_OCxFAST(__HANDLE__, __CHANNEL__) \ + (((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCMR1 &= ~TIM_CCMR1_OC1FE) :\ + ((__CHANNEL__) == TIM_CHANNEL_2) ? ((__HANDLE__)->Instance->CCMR1 &= ~TIM_CCMR1_OC2FE) :\ + ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCMR2 &= ~TIM_CCMR2_OC3FE) :\ + ((__HANDLE__)->Instance->CCMR2 &= ~TIM_CCMR2_OC4FE)) + +/** + * @brief Set the Update Request Source (URS) bit of the TIMx_CR1 register. + * @param __HANDLE__ TIM handle. + * @note When the URS bit of the TIMx_CR1 register is set, only counter + * overflow/underflow generates an update interrupt or DMA request (if + * enabled) + * @retval None + */ +#define __HAL_TIM_URS_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1|= TIM_CR1_URS) + +/** + * @brief Reset the Update Request Source (URS) bit of the TIMx_CR1 register. + * @param __HANDLE__ TIM handle. + * @note When the URS bit of the TIMx_CR1 register is reset, any of the + * following events generate an update interrupt or DMA request (if + * enabled): + * _ Counter overflow underflow + * _ Setting the UG bit + * _ Update generation through the slave mode controller + * @retval None + */ +#define __HAL_TIM_URS_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1&=~TIM_CR1_URS) + +/** + * @brief Set the TIM Capture x input polarity on runtime. + * @param __HANDLE__ TIM handle. + * @param __CHANNEL__ TIM Channels to be configured. + * This parameter can be one of the following values: + * @arg TIM_CHANNEL_1: TIM Channel 1 selected + * @arg TIM_CHANNEL_2: TIM Channel 2 selected + * @arg TIM_CHANNEL_3: TIM Channel 3 selected + * @arg TIM_CHANNEL_4: TIM Channel 4 selected + * @param __POLARITY__ Polarity for TIx source + * @arg TIM_INPUTCHANNELPOLARITY_RISING: Rising Edge + * @arg TIM_INPUTCHANNELPOLARITY_FALLING: Falling Edge + * @arg TIM_INPUTCHANNELPOLARITY_BOTHEDGE: Rising and Falling Edge + * @retval None + */ +#define __HAL_TIM_SET_CAPTUREPOLARITY(__HANDLE__, __CHANNEL__, __POLARITY__) \ + do{ \ + TIM_RESET_CAPTUREPOLARITY((__HANDLE__), (__CHANNEL__)); \ + TIM_SET_CAPTUREPOLARITY((__HANDLE__), (__CHANNEL__), (__POLARITY__)); \ + }while(0) + +/** + * @} + */ +/* End of exported macros ----------------------------------------------------*/ + +/* Private constants ---------------------------------------------------------*/ +/** @defgroup TIM_Private_Constants TIM Private Constants + * @{ + */ +/* The counter of a timer instance is disabled only if all the CCx and CCxN + channels have been disabled */ +#define TIM_CCER_CCxE_MASK ((uint32_t)(TIM_CCER_CC1E | TIM_CCER_CC2E | TIM_CCER_CC3E | TIM_CCER_CC4E)) +#define TIM_CCER_CCxNE_MASK ((uint32_t)(TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) +/** + * @} + */ +/* End of private constants --------------------------------------------------*/ + +/* Private macros ------------------------------------------------------------*/ +/** @defgroup TIM_Private_Macros TIM Private Macros + * @{ + */ +#define IS_TIM_CLEARINPUT_SOURCE(__MODE__) (((__MODE__) == TIM_CLEARINPUTSOURCE_NONE) || \ + ((__MODE__) == TIM_CLEARINPUTSOURCE_ETR)) + +#define IS_TIM_DMA_BASE(__BASE__) (((__BASE__) == TIM_DMABASE_CR1) || \ + ((__BASE__) == TIM_DMABASE_CR2) || \ + ((__BASE__) == TIM_DMABASE_SMCR) || \ + ((__BASE__) == TIM_DMABASE_DIER) || \ + ((__BASE__) == TIM_DMABASE_SR) || \ + ((__BASE__) == TIM_DMABASE_EGR) || \ + ((__BASE__) == TIM_DMABASE_CCMR1) || \ + ((__BASE__) == TIM_DMABASE_CCMR2) || \ + ((__BASE__) == TIM_DMABASE_CCER) || \ + ((__BASE__) == TIM_DMABASE_CNT) || \ + ((__BASE__) == TIM_DMABASE_PSC) || \ + ((__BASE__) == TIM_DMABASE_ARR) || \ + ((__BASE__) == TIM_DMABASE_RCR) || \ + ((__BASE__) == TIM_DMABASE_CCR1) || \ + ((__BASE__) == TIM_DMABASE_CCR2) || \ + ((__BASE__) == TIM_DMABASE_CCR3) || \ + ((__BASE__) == TIM_DMABASE_CCR4) || \ + ((__BASE__) == TIM_DMABASE_BDTR)) + +#define IS_TIM_EVENT_SOURCE(__SOURCE__) ((((__SOURCE__) & 0xFFFFFF00U) == 0x00000000U) && ((__SOURCE__) != 0x00000000U)) + +#define IS_TIM_COUNTER_MODE(__MODE__) (((__MODE__) == TIM_COUNTERMODE_UP) || \ + ((__MODE__) == TIM_COUNTERMODE_DOWN) || \ + ((__MODE__) == TIM_COUNTERMODE_CENTERALIGNED1) || \ + ((__MODE__) == TIM_COUNTERMODE_CENTERALIGNED2) || \ + ((__MODE__) == TIM_COUNTERMODE_CENTERALIGNED3)) + +#define IS_TIM_CLOCKDIVISION_DIV(__DIV__) (((__DIV__) == TIM_CLOCKDIVISION_DIV1) || \ + ((__DIV__) == TIM_CLOCKDIVISION_DIV2) || \ + ((__DIV__) == TIM_CLOCKDIVISION_DIV4)) + +#define IS_TIM_AUTORELOAD_PRELOAD(PRELOAD) (((PRELOAD) == TIM_AUTORELOAD_PRELOAD_DISABLE) || \ + ((PRELOAD) == TIM_AUTORELOAD_PRELOAD_ENABLE)) + +#define IS_TIM_FAST_STATE(__STATE__) (((__STATE__) == TIM_OCFAST_DISABLE) || \ + ((__STATE__) == TIM_OCFAST_ENABLE)) + +#define IS_TIM_OC_POLARITY(__POLARITY__) (((__POLARITY__) == TIM_OCPOLARITY_HIGH) || \ + ((__POLARITY__) == TIM_OCPOLARITY_LOW)) + +#define IS_TIM_OCN_POLARITY(__POLARITY__) (((__POLARITY__) == TIM_OCNPOLARITY_HIGH) || \ + ((__POLARITY__) == TIM_OCNPOLARITY_LOW)) + +#define IS_TIM_OCIDLE_STATE(__STATE__) (((__STATE__) == TIM_OCIDLESTATE_SET) || \ + ((__STATE__) == TIM_OCIDLESTATE_RESET)) + +#define IS_TIM_OCNIDLE_STATE(__STATE__) (((__STATE__) == TIM_OCNIDLESTATE_SET) || \ + ((__STATE__) == TIM_OCNIDLESTATE_RESET)) + +#define IS_TIM_IC_POLARITY(__POLARITY__) (((__POLARITY__) == TIM_ICPOLARITY_RISING) || \ + ((__POLARITY__) == TIM_ICPOLARITY_FALLING) || \ + ((__POLARITY__) == TIM_ICPOLARITY_BOTHEDGE)) + +#define IS_TIM_IC_SELECTION(__SELECTION__) (((__SELECTION__) == TIM_ICSELECTION_DIRECTTI) || \ + ((__SELECTION__) == TIM_ICSELECTION_INDIRECTTI) || \ + ((__SELECTION__) == TIM_ICSELECTION_TRC)) + +#define IS_TIM_IC_PRESCALER(__PRESCALER__) (((__PRESCALER__) == TIM_ICPSC_DIV1) || \ + ((__PRESCALER__) == TIM_ICPSC_DIV2) || \ + ((__PRESCALER__) == TIM_ICPSC_DIV4) || \ + ((__PRESCALER__) == TIM_ICPSC_DIV8)) + +#define IS_TIM_OPM_MODE(__MODE__) (((__MODE__) == TIM_OPMODE_SINGLE) || \ + ((__MODE__) == TIM_OPMODE_REPETITIVE)) + +#define IS_TIM_ENCODER_MODE(__MODE__) (((__MODE__) == TIM_ENCODERMODE_TI1) || \ + ((__MODE__) == TIM_ENCODERMODE_TI2) || \ + ((__MODE__) == TIM_ENCODERMODE_TI12)) + +#define IS_TIM_DMA_SOURCE(__SOURCE__) ((((__SOURCE__) & 0xFFFF80FFU) == 0x00000000U) && ((__SOURCE__) != 0x00000000U)) + +#define IS_TIM_CHANNELS(__CHANNEL__) (((__CHANNEL__) == TIM_CHANNEL_1) || \ + ((__CHANNEL__) == TIM_CHANNEL_2) || \ + ((__CHANNEL__) == TIM_CHANNEL_3) || \ + ((__CHANNEL__) == TIM_CHANNEL_4) || \ + ((__CHANNEL__) == TIM_CHANNEL_ALL)) + +#define IS_TIM_OPM_CHANNELS(__CHANNEL__) (((__CHANNEL__) == TIM_CHANNEL_1) || \ + ((__CHANNEL__) == TIM_CHANNEL_2)) + +#define IS_TIM_COMPLEMENTARY_CHANNELS(__CHANNEL__) (((__CHANNEL__) == TIM_CHANNEL_1) || \ + ((__CHANNEL__) == TIM_CHANNEL_2) || \ + ((__CHANNEL__) == TIM_CHANNEL_3)) + +#define IS_TIM_CLOCKSOURCE(__CLOCK__) (((__CLOCK__) == TIM_CLOCKSOURCE_INTERNAL) || \ + ((__CLOCK__) == TIM_CLOCKSOURCE_ETRMODE2) || \ + ((__CLOCK__) == TIM_CLOCKSOURCE_ITR0) || \ + ((__CLOCK__) == TIM_CLOCKSOURCE_ITR1) || \ + ((__CLOCK__) == TIM_CLOCKSOURCE_ITR2) || \ + ((__CLOCK__) == TIM_CLOCKSOURCE_ITR3) || \ + ((__CLOCK__) == TIM_CLOCKSOURCE_TI1ED) || \ + ((__CLOCK__) == TIM_CLOCKSOURCE_TI1) || \ + ((__CLOCK__) == TIM_CLOCKSOURCE_TI2) || \ + ((__CLOCK__) == TIM_CLOCKSOURCE_ETRMODE1)) + +#define IS_TIM_CLOCKPOLARITY(__POLARITY__) (((__POLARITY__) == TIM_CLOCKPOLARITY_INVERTED) || \ + ((__POLARITY__) == TIM_CLOCKPOLARITY_NONINVERTED) || \ + ((__POLARITY__) == TIM_CLOCKPOLARITY_RISING) || \ + ((__POLARITY__) == TIM_CLOCKPOLARITY_FALLING) || \ + ((__POLARITY__) == TIM_CLOCKPOLARITY_BOTHEDGE)) + +#define IS_TIM_CLOCKPRESCALER(__PRESCALER__) (((__PRESCALER__) == TIM_CLOCKPRESCALER_DIV1) || \ + ((__PRESCALER__) == TIM_CLOCKPRESCALER_DIV2) || \ + ((__PRESCALER__) == TIM_CLOCKPRESCALER_DIV4) || \ + ((__PRESCALER__) == TIM_CLOCKPRESCALER_DIV8)) + +#define IS_TIM_CLOCKFILTER(__ICFILTER__) ((__ICFILTER__) <= 0xFU) + +#define IS_TIM_CLEARINPUT_POLARITY(__POLARITY__) (((__POLARITY__) == TIM_CLEARINPUTPOLARITY_INVERTED) || \ + ((__POLARITY__) == TIM_CLEARINPUTPOLARITY_NONINVERTED)) + +#define IS_TIM_CLEARINPUT_PRESCALER(__PRESCALER__) (((__PRESCALER__) == TIM_CLEARINPUTPRESCALER_DIV1) || \ + ((__PRESCALER__) == TIM_CLEARINPUTPRESCALER_DIV2) || \ + ((__PRESCALER__) == TIM_CLEARINPUTPRESCALER_DIV4) || \ + ((__PRESCALER__) == TIM_CLEARINPUTPRESCALER_DIV8)) + +#define IS_TIM_CLEARINPUT_FILTER(__ICFILTER__) ((__ICFILTER__) <= 0xFU) + +#define IS_TIM_OSSR_STATE(__STATE__) (((__STATE__) == TIM_OSSR_ENABLE) || \ + ((__STATE__) == TIM_OSSR_DISABLE)) + +#define IS_TIM_OSSI_STATE(__STATE__) (((__STATE__) == TIM_OSSI_ENABLE) || \ + ((__STATE__) == TIM_OSSI_DISABLE)) + +#define IS_TIM_LOCK_LEVEL(__LEVEL__) (((__LEVEL__) == TIM_LOCKLEVEL_OFF) || \ + ((__LEVEL__) == TIM_LOCKLEVEL_1) || \ + ((__LEVEL__) == TIM_LOCKLEVEL_2) || \ + ((__LEVEL__) == TIM_LOCKLEVEL_3)) + +#define IS_TIM_BREAK_FILTER(__BRKFILTER__) ((__BRKFILTER__) <= 0xFUL) + + +#define IS_TIM_BREAK_STATE(__STATE__) (((__STATE__) == TIM_BREAK_ENABLE) || \ + ((__STATE__) == TIM_BREAK_DISABLE)) + +#define IS_TIM_BREAK_POLARITY(__POLARITY__) (((__POLARITY__) == TIM_BREAKPOLARITY_LOW) || \ + ((__POLARITY__) == TIM_BREAKPOLARITY_HIGH)) + +#define IS_TIM_AUTOMATIC_OUTPUT_STATE(__STATE__) (((__STATE__) == TIM_AUTOMATICOUTPUT_ENABLE) || \ + ((__STATE__) == TIM_AUTOMATICOUTPUT_DISABLE)) + +#define IS_TIM_TRGO_SOURCE(__SOURCE__) (((__SOURCE__) == TIM_TRGO_RESET) || \ + ((__SOURCE__) == TIM_TRGO_ENABLE) || \ + ((__SOURCE__) == TIM_TRGO_UPDATE) || \ + ((__SOURCE__) == TIM_TRGO_OC1) || \ + ((__SOURCE__) == TIM_TRGO_OC1REF) || \ + ((__SOURCE__) == TIM_TRGO_OC2REF) || \ + ((__SOURCE__) == TIM_TRGO_OC3REF) || \ + ((__SOURCE__) == TIM_TRGO_OC4REF)) + +#define IS_TIM_MSM_STATE(__STATE__) (((__STATE__) == TIM_MASTERSLAVEMODE_ENABLE) || \ + ((__STATE__) == TIM_MASTERSLAVEMODE_DISABLE)) + +#define IS_TIM_SLAVE_MODE(__MODE__) (((__MODE__) == TIM_SLAVEMODE_DISABLE) || \ + ((__MODE__) == TIM_SLAVEMODE_RESET) || \ + ((__MODE__) == TIM_SLAVEMODE_GATED) || \ + ((__MODE__) == TIM_SLAVEMODE_TRIGGER) || \ + ((__MODE__) == TIM_SLAVEMODE_EXTERNAL1)) + +#define IS_TIM_PWM_MODE(__MODE__) (((__MODE__) == TIM_OCMODE_PWM1) || \ + ((__MODE__) == TIM_OCMODE_PWM2)) + +#define IS_TIM_OC_MODE(__MODE__) (((__MODE__) == TIM_OCMODE_TIMING) || \ + ((__MODE__) == TIM_OCMODE_ACTIVE) || \ + ((__MODE__) == TIM_OCMODE_INACTIVE) || \ + ((__MODE__) == TIM_OCMODE_TOGGLE) || \ + ((__MODE__) == TIM_OCMODE_FORCED_ACTIVE) || \ + ((__MODE__) == TIM_OCMODE_FORCED_INACTIVE)) + +#define IS_TIM_TRIGGER_SELECTION(__SELECTION__) (((__SELECTION__) == TIM_TS_ITR0) || \ + ((__SELECTION__) == TIM_TS_ITR1) || \ + ((__SELECTION__) == TIM_TS_ITR2) || \ + ((__SELECTION__) == TIM_TS_ITR3) || \ + ((__SELECTION__) == TIM_TS_TI1F_ED) || \ + ((__SELECTION__) == TIM_TS_TI1FP1) || \ + ((__SELECTION__) == TIM_TS_TI2FP2) || \ + ((__SELECTION__) == TIM_TS_ETRF)) + +#define IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(__SELECTION__) (((__SELECTION__) == TIM_TS_ITR0) || \ + ((__SELECTION__) == TIM_TS_ITR1) || \ + ((__SELECTION__) == TIM_TS_ITR2) || \ + ((__SELECTION__) == TIM_TS_ITR3) || \ + ((__SELECTION__) == TIM_TS_NONE)) + +#define IS_TIM_TRIGGERPOLARITY(__POLARITY__) (((__POLARITY__) == TIM_TRIGGERPOLARITY_INVERTED ) || \ + ((__POLARITY__) == TIM_TRIGGERPOLARITY_NONINVERTED) || \ + ((__POLARITY__) == TIM_TRIGGERPOLARITY_RISING ) || \ + ((__POLARITY__) == TIM_TRIGGERPOLARITY_FALLING ) || \ + ((__POLARITY__) == TIM_TRIGGERPOLARITY_BOTHEDGE )) + +#define IS_TIM_TRIGGERPRESCALER(__PRESCALER__) (((__PRESCALER__) == TIM_TRIGGERPRESCALER_DIV1) || \ + ((__PRESCALER__) == TIM_TRIGGERPRESCALER_DIV2) || \ + ((__PRESCALER__) == TIM_TRIGGERPRESCALER_DIV4) || \ + ((__PRESCALER__) == TIM_TRIGGERPRESCALER_DIV8)) + +#define IS_TIM_TRIGGERFILTER(__ICFILTER__) ((__ICFILTER__) <= 0xFU) + +#define IS_TIM_TI1SELECTION(__TI1SELECTION__) (((__TI1SELECTION__) == TIM_TI1SELECTION_CH1) || \ + ((__TI1SELECTION__) == TIM_TI1SELECTION_XORCOMBINATION)) + +#define IS_TIM_DMA_LENGTH(__LENGTH__) (((__LENGTH__) == TIM_DMABURSTLENGTH_1TRANSFER) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_2TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_3TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_4TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_5TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_6TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_7TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_8TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_9TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_10TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_11TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_12TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_13TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_14TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_15TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_16TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_17TRANSFERS) || \ + ((__LENGTH__) == TIM_DMABURSTLENGTH_18TRANSFERS)) + +#define IS_TIM_IC_FILTER(__ICFILTER__) ((__ICFILTER__) <= 0xFU) + +#define IS_TIM_DEADTIME(__DEADTIME__) ((__DEADTIME__) <= 0xFFU) + +#define IS_TIM_SLAVEMODE_TRIGGER_ENABLED(__TRIGGER__) ((__TRIGGER__) == TIM_SLAVEMODE_TRIGGER) + +#define TIM_SET_ICPRESCALERVALUE(__HANDLE__, __CHANNEL__, __ICPSC__) \ + (((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCMR1 |= (__ICPSC__)) :\ + ((__CHANNEL__) == TIM_CHANNEL_2) ? ((__HANDLE__)->Instance->CCMR1 |= ((__ICPSC__) << 8U)) :\ + ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCMR2 |= (__ICPSC__)) :\ + ((__HANDLE__)->Instance->CCMR2 |= ((__ICPSC__) << 8U))) + +#define TIM_RESET_ICPRESCALERVALUE(__HANDLE__, __CHANNEL__) \ + (((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCMR1 &= ~TIM_CCMR1_IC1PSC) :\ + ((__CHANNEL__) == TIM_CHANNEL_2) ? ((__HANDLE__)->Instance->CCMR1 &= ~TIM_CCMR1_IC2PSC) :\ + ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCMR2 &= ~TIM_CCMR2_IC3PSC) :\ + ((__HANDLE__)->Instance->CCMR2 &= ~TIM_CCMR2_IC4PSC)) + +#define TIM_SET_CAPTUREPOLARITY(__HANDLE__, __CHANNEL__, __POLARITY__) \ + (((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCER |= (__POLARITY__)) :\ + ((__CHANNEL__) == TIM_CHANNEL_2) ? ((__HANDLE__)->Instance->CCER |= ((__POLARITY__) << 4U)) :\ + ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCER |= ((__POLARITY__) << 8U)) :\ + ((__HANDLE__)->Instance->CCER |= (((__POLARITY__) << 12U)))) + +#define TIM_RESET_CAPTUREPOLARITY(__HANDLE__, __CHANNEL__) \ + (((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCER &= ~(TIM_CCER_CC1P | TIM_CCER_CC1NP))) :\ + ((__CHANNEL__) == TIM_CHANNEL_2) ? ((__HANDLE__)->Instance->CCER &= ~(TIM_CCER_CC2P | TIM_CCER_CC2NP)) :\ + ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCER &= ~(TIM_CCER_CC3P)) :\ + ((__HANDLE__)->Instance->CCER &= ~(TIM_CCER_CC4P))) + +/** + * @} + */ +/* End of private macros -----------------------------------------------------*/ + +/* Include TIM HAL Extended module */ +#include "stm32f1xx_hal_tim_ex.h" + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup TIM_Exported_Functions TIM Exported Functions + * @{ + */ + +/** @addtogroup TIM_Exported_Functions_Group1 TIM Time Base functions + * @brief Time Base functions + * @{ + */ +/* Time Base functions ********************************************************/ +HAL_StatusTypeDef HAL_TIM_Base_Init(TIM_HandleTypeDef* htim); +HAL_StatusTypeDef HAL_TIM_Base_DeInit(TIM_HandleTypeDef* htim); +void HAL_TIM_Base_MspInit(TIM_HandleTypeDef* htim); +void HAL_TIM_Base_MspDeInit(TIM_HandleTypeDef* htim); +/* Blocking mode: Polling */ +HAL_StatusTypeDef HAL_TIM_Base_Start(TIM_HandleTypeDef* htim); +HAL_StatusTypeDef HAL_TIM_Base_Stop(TIM_HandleTypeDef* htim); +/* Non-Blocking mode: Interrupt */ +HAL_StatusTypeDef HAL_TIM_Base_Start_IT(TIM_HandleTypeDef* htim); +HAL_StatusTypeDef HAL_TIM_Base_Stop_IT(TIM_HandleTypeDef* htim); +/* Non-Blocking mode: DMA */ +HAL_StatusTypeDef HAL_TIM_Base_Start_DMA(TIM_HandleTypeDef* htim, uint32_t* pData, uint16_t Length); +HAL_StatusTypeDef HAL_TIM_Base_Stop_DMA(TIM_HandleTypeDef* htim); +/** + * @} + */ + +/** @addtogroup TIM_Exported_Functions_Group2 TIM Output Compare functions + * @brief TIM Output Compare functions + * @{ + */ +/* Timer Output Compare functions *********************************************/ +HAL_StatusTypeDef HAL_TIM_OC_Init(TIM_HandleTypeDef* htim); +HAL_StatusTypeDef HAL_TIM_OC_DeInit(TIM_HandleTypeDef* htim); +void HAL_TIM_OC_MspInit(TIM_HandleTypeDef* htim); +void HAL_TIM_OC_MspDeInit(TIM_HandleTypeDef* htim); +/* Blocking mode: Polling */ +HAL_StatusTypeDef HAL_TIM_OC_Start(TIM_HandleTypeDef* htim, uint32_t Channel); +HAL_StatusTypeDef HAL_TIM_OC_Stop(TIM_HandleTypeDef* htim, uint32_t Channel); +/* Non-Blocking mode: Interrupt */ +HAL_StatusTypeDef HAL_TIM_OC_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel); +HAL_StatusTypeDef HAL_TIM_OC_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel); +/* Non-Blocking mode: DMA */ +HAL_StatusTypeDef HAL_TIM_OC_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData, uint16_t Length); +HAL_StatusTypeDef HAL_TIM_OC_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel); +/** + * @} + */ + +/** @addtogroup TIM_Exported_Functions_Group3 TIM PWM functions + * @brief TIM PWM functions + * @{ + */ +/* Timer PWM functions ********************************************************/ +HAL_StatusTypeDef HAL_TIM_PWM_Init(TIM_HandleTypeDef* htim); +HAL_StatusTypeDef HAL_TIM_PWM_DeInit(TIM_HandleTypeDef* htim); +void HAL_TIM_PWM_MspInit(TIM_HandleTypeDef* htim); +void HAL_TIM_PWM_MspDeInit(TIM_HandleTypeDef* htim); +/* Blocking mode: Polling */ +HAL_StatusTypeDef HAL_TIM_PWM_Start(TIM_HandleTypeDef* htim, uint32_t Channel); +HAL_StatusTypeDef HAL_TIM_PWM_Stop(TIM_HandleTypeDef* htim, uint32_t Channel); +/* Non-Blocking mode: Interrupt */ +HAL_StatusTypeDef HAL_TIM_PWM_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel); +HAL_StatusTypeDef HAL_TIM_PWM_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel); +/* Non-Blocking mode: DMA */ +HAL_StatusTypeDef HAL_TIM_PWM_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData, uint16_t Length); +HAL_StatusTypeDef HAL_TIM_PWM_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel); +/** + * @} + */ + +/** @addtogroup TIM_Exported_Functions_Group4 TIM Input Capture functions + * @brief TIM Input Capture functions + * @{ + */ +/* Timer Input Capture functions **********************************************/ +HAL_StatusTypeDef HAL_TIM_IC_Init(TIM_HandleTypeDef* htim); +HAL_StatusTypeDef HAL_TIM_IC_DeInit(TIM_HandleTypeDef* htim); +void HAL_TIM_IC_MspInit(TIM_HandleTypeDef* htim); +void HAL_TIM_IC_MspDeInit(TIM_HandleTypeDef* htim); +/* Blocking mode: Polling */ +HAL_StatusTypeDef HAL_TIM_IC_Start(TIM_HandleTypeDef* htim, uint32_t Channel); +HAL_StatusTypeDef HAL_TIM_IC_Stop(TIM_HandleTypeDef* htim, uint32_t Channel); +/* Non-Blocking mode: Interrupt */ +HAL_StatusTypeDef HAL_TIM_IC_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel); +HAL_StatusTypeDef HAL_TIM_IC_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel); +/* Non-Blocking mode: DMA */ +HAL_StatusTypeDef HAL_TIM_IC_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData, uint16_t Length); +HAL_StatusTypeDef HAL_TIM_IC_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel); +/** + * @} + */ + +/** @addtogroup TIM_Exported_Functions_Group5 TIM One Pulse functions + * @brief TIM One Pulse functions + * @{ + */ +/* Timer One Pulse functions **************************************************/ +HAL_StatusTypeDef HAL_TIM_OnePulse_Init(TIM_HandleTypeDef* htim, uint32_t OnePulseMode); +HAL_StatusTypeDef HAL_TIM_OnePulse_DeInit(TIM_HandleTypeDef* htim); +void HAL_TIM_OnePulse_MspInit(TIM_HandleTypeDef* htim); +void HAL_TIM_OnePulse_MspDeInit(TIM_HandleTypeDef* htim); +/* Blocking mode: Polling */ +HAL_StatusTypeDef HAL_TIM_OnePulse_Start(TIM_HandleTypeDef* htim, uint32_t OutputChannel); +HAL_StatusTypeDef HAL_TIM_OnePulse_Stop(TIM_HandleTypeDef* htim, uint32_t OutputChannel); +/* Non-Blocking mode: Interrupt */ +HAL_StatusTypeDef HAL_TIM_OnePulse_Start_IT(TIM_HandleTypeDef* htim, uint32_t OutputChannel); +HAL_StatusTypeDef HAL_TIM_OnePulse_Stop_IT(TIM_HandleTypeDef* htim, uint32_t OutputChannel); +/** + * @} + */ + +/** @addtogroup TIM_Exported_Functions_Group6 TIM Encoder functions + * @brief TIM Encoder functions + * @{ + */ +/* Timer Encoder functions ****************************************************/ +HAL_StatusTypeDef HAL_TIM_Encoder_Init(TIM_HandleTypeDef* htim, TIM_Encoder_InitTypeDef* sConfig); +HAL_StatusTypeDef HAL_TIM_Encoder_DeInit(TIM_HandleTypeDef* htim); +void HAL_TIM_Encoder_MspInit(TIM_HandleTypeDef* htim); +void HAL_TIM_Encoder_MspDeInit(TIM_HandleTypeDef* htim); +/* Blocking mode: Polling */ +HAL_StatusTypeDef HAL_TIM_Encoder_Start(TIM_HandleTypeDef* htim, uint32_t Channel); +HAL_StatusTypeDef HAL_TIM_Encoder_Stop(TIM_HandleTypeDef* htim, uint32_t Channel); +/* Non-Blocking mode: Interrupt */ +HAL_StatusTypeDef HAL_TIM_Encoder_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel); +HAL_StatusTypeDef HAL_TIM_Encoder_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel); +/* Non-Blocking mode: DMA */ +HAL_StatusTypeDef HAL_TIM_Encoder_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData1, + uint32_t* pData2, uint16_t Length); +HAL_StatusTypeDef HAL_TIM_Encoder_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel); +/** + * @} + */ + +/** @addtogroup TIM_Exported_Functions_Group7 TIM IRQ handler management + * @brief IRQ handler management + * @{ + */ +/* Interrupt Handler functions ***********************************************/ +void HAL_TIM_IRQHandler(TIM_HandleTypeDef* htim); +/** + * @} + */ + +/** @defgroup TIM_Exported_Functions_Group8 TIM Peripheral Control functions + * @brief Peripheral Control functions + * @{ + */ +/* Control functions *********************************************************/ +HAL_StatusTypeDef HAL_TIM_OC_ConfigChannel(TIM_HandleTypeDef* htim, TIM_OC_InitTypeDef* sConfig, uint32_t Channel); +HAL_StatusTypeDef HAL_TIM_PWM_ConfigChannel(TIM_HandleTypeDef* htim, TIM_OC_InitTypeDef* sConfig, uint32_t Channel); +HAL_StatusTypeDef HAL_TIM_IC_ConfigChannel(TIM_HandleTypeDef* htim, TIM_IC_InitTypeDef* sConfig, uint32_t Channel); +HAL_StatusTypeDef HAL_TIM_OnePulse_ConfigChannel(TIM_HandleTypeDef* htim, TIM_OnePulse_InitTypeDef* sConfig, + uint32_t OutputChannel, uint32_t InputChannel); +HAL_StatusTypeDef HAL_TIM_ConfigOCrefClear(TIM_HandleTypeDef* htim, TIM_ClearInputConfigTypeDef* sClearInputConfig, + uint32_t Channel); +HAL_StatusTypeDef HAL_TIM_ConfigClockSource(TIM_HandleTypeDef* htim, TIM_ClockConfigTypeDef* sClockSourceConfig); +HAL_StatusTypeDef HAL_TIM_ConfigTI1Input(TIM_HandleTypeDef* htim, uint32_t TI1_Selection); +HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchro(TIM_HandleTypeDef* htim, TIM_SlaveConfigTypeDef* sSlaveConfig); +HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchro_IT(TIM_HandleTypeDef* htim, TIM_SlaveConfigTypeDef* sSlaveConfig); +HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStart(TIM_HandleTypeDef* htim, uint32_t BurstBaseAddress, + uint32_t BurstRequestSrc, uint32_t* BurstBuffer, uint32_t BurstLength); +HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStop(TIM_HandleTypeDef* htim, uint32_t BurstRequestSrc); +HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStart(TIM_HandleTypeDef* htim, uint32_t BurstBaseAddress, + uint32_t BurstRequestSrc, uint32_t* BurstBuffer, uint32_t BurstLength); +HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStop(TIM_HandleTypeDef* htim, uint32_t BurstRequestSrc); +HAL_StatusTypeDef HAL_TIM_GenerateEvent(TIM_HandleTypeDef* htim, uint32_t EventSource); +uint32_t HAL_TIM_ReadCapturedValue(TIM_HandleTypeDef* htim, uint32_t Channel); +/** + * @} + */ + +/** @defgroup TIM_Exported_Functions_Group9 TIM Callbacks functions + * @brief TIM Callbacks functions + * @{ + */ +/* Callback in non blocking modes (Interrupt and DMA) *************************/ +void HAL_TIM_PeriodElapsedCallback(TIM_HandleTypeDef* htim); +void HAL_TIM_PeriodElapsedHalfCpltCallback(TIM_HandleTypeDef* htim); +void HAL_TIM_OC_DelayElapsedCallback(TIM_HandleTypeDef* htim); +void HAL_TIM_IC_CaptureCallback(TIM_HandleTypeDef* htim); +void HAL_TIM_IC_CaptureHalfCpltCallback(TIM_HandleTypeDef* htim); +void HAL_TIM_PWM_PulseFinishedCallback(TIM_HandleTypeDef* htim); +void HAL_TIM_PWM_PulseFinishedHalfCpltCallback(TIM_HandleTypeDef* htim); +void HAL_TIM_TriggerCallback(TIM_HandleTypeDef* htim); +void HAL_TIM_TriggerHalfCpltCallback(TIM_HandleTypeDef* htim); +void HAL_TIM_ErrorCallback(TIM_HandleTypeDef* htim); + +/* Callbacks Register/UnRegister functions ***********************************/ +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) +HAL_StatusTypeDef HAL_TIM_RegisterCallback(TIM_HandleTypeDef* htim, HAL_TIM_CallbackIDTypeDef CallbackID, + pTIM_CallbackTypeDef pCallback); +HAL_StatusTypeDef HAL_TIM_UnRegisterCallback(TIM_HandleTypeDef* htim, HAL_TIM_CallbackIDTypeDef CallbackID); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + +/** + * @} + */ + +/** @defgroup TIM_Exported_Functions_Group10 TIM Peripheral State functions + * @brief Peripheral State functions + * @{ + */ +/* Peripheral State functions ************************************************/ +HAL_TIM_StateTypeDef HAL_TIM_Base_GetState(TIM_HandleTypeDef* htim); +HAL_TIM_StateTypeDef HAL_TIM_OC_GetState(TIM_HandleTypeDef* htim); +HAL_TIM_StateTypeDef HAL_TIM_PWM_GetState(TIM_HandleTypeDef* htim); +HAL_TIM_StateTypeDef HAL_TIM_IC_GetState(TIM_HandleTypeDef* htim); +HAL_TIM_StateTypeDef HAL_TIM_OnePulse_GetState(TIM_HandleTypeDef* htim); +HAL_TIM_StateTypeDef HAL_TIM_Encoder_GetState(TIM_HandleTypeDef* htim); +/** + * @} + */ + +/** + * @} + */ +/* End of exported functions -------------------------------------------------*/ + +/* Private functions----------------------------------------------------------*/ +/** @defgroup TIM_Private_Functions TIM Private Functions + * @{ + */ +void TIM_Base_SetConfig(TIM_TypeDef* TIMx, TIM_Base_InitTypeDef* Structure); +void TIM_TI1_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter); +void TIM_OC2_SetConfig(TIM_TypeDef* TIMx, TIM_OC_InitTypeDef* OC_Config); +void TIM_ETR_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ExtTRGPrescaler, + uint32_t TIM_ExtTRGPolarity, uint32_t ExtTRGFilter); + +void TIM_DMADelayPulseCplt(DMA_HandleTypeDef* hdma); +void TIM_DMADelayPulseHalfCplt(DMA_HandleTypeDef* hdma); +void TIM_DMAError(DMA_HandleTypeDef* hdma); +void TIM_DMACaptureCplt(DMA_HandleTypeDef* hdma); +void TIM_DMACaptureHalfCplt(DMA_HandleTypeDef* hdma); +void TIM_CCxChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelState); + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) +void TIM_ResetCallback(TIM_HandleTypeDef* htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + +/** + * @} + */ +/* End of private functions --------------------------------------------------*/ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* STM32F1xx_HAL_TIM_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_tim_ex.h b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_tim_ex.h new file mode 100644 index 00000000..785a1955 --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_tim_ex.h @@ -0,0 +1,261 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_tim_ex.h + * @author MCD Application Team + * @brief Header file of TIM HAL Extended module. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef STM32F1xx_HAL_TIM_EX_H +#define STM32F1xx_HAL_TIM_EX_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal_def.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @addtogroup TIMEx + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ +/** @defgroup TIMEx_Exported_Types TIM Extended Exported Types + * @{ + */ + +/** + * @brief TIM Hall sensor Configuration Structure definition + */ + +typedef struct +{ + uint32_t IC1Polarity; /*!< Specifies the active edge of the input signal. + This parameter can be a value of @ref TIM_Input_Capture_Polarity */ + + uint32_t IC1Prescaler; /*!< Specifies the Input Capture Prescaler. + This parameter can be a value of @ref TIM_Input_Capture_Prescaler */ + + uint32_t IC1Filter; /*!< Specifies the input capture filter. + This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ + + uint32_t Commutation_Delay; /*!< Specifies the pulse value to be loaded into the Capture Compare Register. + This parameter can be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF */ +} TIM_HallSensor_InitTypeDef; +/** + * @} + */ +/* End of exported types -----------------------------------------------------*/ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup TIMEx_Exported_Constants TIM Extended Exported Constants + * @{ + */ + +/** @defgroup TIMEx_Remap TIM Extended Remapping + * @{ + */ +/** + * @} + */ + +/** + * @} + */ +/* End of exported constants -------------------------------------------------*/ + +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup TIMEx_Exported_Macros TIM Extended Exported Macros + * @{ + */ + +/** + * @} + */ +/* End of exported macro -----------------------------------------------------*/ + +/* Private macro -------------------------------------------------------------*/ +/** @defgroup TIMEx_Private_Macros TIM Extended Private Macros + * @{ + */ + +/** + * @} + */ +/* End of private macro ------------------------------------------------------*/ + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup TIMEx_Exported_Functions TIM Extended Exported Functions + * @{ + */ + +/** @addtogroup TIMEx_Exported_Functions_Group1 Extended Timer Hall Sensor functions + * @brief Timer Hall Sensor functions + * @{ + */ +/* Timer Hall Sensor functions **********************************************/ +HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef* htim, TIM_HallSensor_InitTypeDef* sConfig); +HAL_StatusTypeDef HAL_TIMEx_HallSensor_DeInit(TIM_HandleTypeDef* htim); + +void HAL_TIMEx_HallSensor_MspInit(TIM_HandleTypeDef* htim); +void HAL_TIMEx_HallSensor_MspDeInit(TIM_HandleTypeDef* htim); + +/* Blocking mode: Polling */ +HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start(TIM_HandleTypeDef* htim); +HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop(TIM_HandleTypeDef* htim); +/* Non-Blocking mode: Interrupt */ +HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_IT(TIM_HandleTypeDef* htim); +HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_IT(TIM_HandleTypeDef* htim); +/* Non-Blocking mode: DMA */ +HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_DMA(TIM_HandleTypeDef* htim, uint32_t* pData, uint16_t Length); +HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_DMA(TIM_HandleTypeDef* htim); +/** + * @} + */ + +/** @addtogroup TIMEx_Exported_Functions_Group2 Extended Timer Complementary Output Compare functions + * @brief Timer Complementary Output Compare functions + * @{ + */ +/* Timer Complementary Output Compare functions *****************************/ +/* Blocking mode: Polling */ +HAL_StatusTypeDef HAL_TIMEx_OCN_Start(TIM_HandleTypeDef* htim, uint32_t Channel); +HAL_StatusTypeDef HAL_TIMEx_OCN_Stop(TIM_HandleTypeDef* htim, uint32_t Channel); + +/* Non-Blocking mode: Interrupt */ +HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel); +HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel); + +/* Non-Blocking mode: DMA */ +HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData, uint16_t Length); +HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel); +/** + * @} + */ + +/** @addtogroup TIMEx_Exported_Functions_Group3 Extended Timer Complementary PWM functions + * @brief Timer Complementary PWM functions + * @{ + */ +/* Timer Complementary PWM functions ****************************************/ +/* Blocking mode: Polling */ +HAL_StatusTypeDef HAL_TIMEx_PWMN_Start(TIM_HandleTypeDef* htim, uint32_t Channel); +HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop(TIM_HandleTypeDef* htim, uint32_t Channel); + +/* Non-Blocking mode: Interrupt */ +HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel); +HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel); +/* Non-Blocking mode: DMA */ +HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData, uint16_t Length); +HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel); +/** + * @} + */ + +/** @addtogroup TIMEx_Exported_Functions_Group4 Extended Timer Complementary One Pulse functions + * @brief Timer Complementary One Pulse functions + * @{ + */ +/* Timer Complementary One Pulse functions **********************************/ +/* Blocking mode: Polling */ +HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef* htim, uint32_t OutputChannel); +HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop(TIM_HandleTypeDef* htim, uint32_t OutputChannel); + +/* Non-Blocking mode: Interrupt */ +HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start_IT(TIM_HandleTypeDef* htim, uint32_t OutputChannel); +HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop_IT(TIM_HandleTypeDef* htim, uint32_t OutputChannel); +/** + * @} + */ + +/** @addtogroup TIMEx_Exported_Functions_Group5 Extended Peripheral Control functions + * @brief Peripheral Control functions + * @{ + */ +/* Extended Control functions ************************************************/ +HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent(TIM_HandleTypeDef* htim, uint32_t InputTrigger, + uint32_t CommutationSource); +HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent_IT(TIM_HandleTypeDef* htim, uint32_t InputTrigger, + uint32_t CommutationSource); +HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent_DMA(TIM_HandleTypeDef* htim, uint32_t InputTrigger, + uint32_t CommutationSource); +HAL_StatusTypeDef HAL_TIMEx_MasterConfigSynchronization(TIM_HandleTypeDef* htim, + TIM_MasterConfigTypeDef* sMasterConfig); +HAL_StatusTypeDef HAL_TIMEx_ConfigBreakDeadTime(TIM_HandleTypeDef* htim, + TIM_BreakDeadTimeConfigTypeDef* sBreakDeadTimeConfig); +HAL_StatusTypeDef HAL_TIMEx_RemapConfig(TIM_HandleTypeDef* htim, uint32_t Remap); +/** + * @} + */ + +/** @addtogroup TIMEx_Exported_Functions_Group6 Extended Callbacks functions + * @brief Extended Callbacks functions + * @{ + */ +/* Extended Callback **********************************************************/ +void HAL_TIMEx_CommutCallback(TIM_HandleTypeDef* htim); +void HAL_TIMEx_CommutHalfCpltCallback(TIM_HandleTypeDef* htim); +void HAL_TIMEx_BreakCallback(TIM_HandleTypeDef* htim); +/** + * @} + */ + +/** @addtogroup TIMEx_Exported_Functions_Group7 Extended Peripheral State functions + * @brief Extended Peripheral State functions + * @{ + */ +/* Extended Peripheral State functions ***************************************/ +HAL_TIM_StateTypeDef HAL_TIMEx_HallSensor_GetState(TIM_HandleTypeDef* htim); +/** + * @} + */ + +/** + * @} + */ +/* End of exported functions -------------------------------------------------*/ + +/* Private functions----------------------------------------------------------*/ +/** @addtogroup TIMEx_Private_Functions TIMEx Private Functions + * @{ + */ +void TIMEx_DMACommutationCplt(DMA_HandleTypeDef* hdma); +void TIMEx_DMACommutationHalfCplt(DMA_HandleTypeDef* hdma); +/** + * @} + */ +/* End of private functions --------------------------------------------------*/ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + + +#endif /* STM32F1xx_HAL_TIM_EX_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal.c b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal.c similarity index 54% rename from EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal.c rename to EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal.c index c8fa212f..0420c82a 100644 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal.c +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal.c @@ -1,9 +1,7 @@ /** ****************************************************************************** - * @file stm32f4xx_hal.c + * @file stm32f1xx_hal.c * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 * @brief HAL module driver. * This is the common part of the HAL initialization * @@ -23,37 +21,21 @@ ****************************************************************************** * @attention * - *

© COPYRIGHT(c) 2016 STMicroelectronics

+ *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

* - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause * ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" +#include "stm32f1xx_hal.h" -/** @addtogroup STM32F4xx_HAL_Driver +/** @addtogroup STM32F1xx_HAL_Driver * @{ */ @@ -62,53 +44,46 @@ * @{ */ +#ifdef HAL_MODULE_ENABLED + /* Private typedef -----------------------------------------------------------*/ /* Private define ------------------------------------------------------------*/ -/** @addtogroup HAL_Private_Constants + +/** @defgroup HAL_Private_Constants HAL Private Constants * @{ */ /** - * @brief STM32F4xx HAL Driver version number V1.5.0 - */ -#define __STM32F4xx_HAL_VERSION_MAIN (0x01) /*!< [31:24] main version */ -#define __STM32F4xx_HAL_VERSION_SUB1 (0x05) /*!< [23:16] sub1 version */ -#define __STM32F4xx_HAL_VERSION_SUB2 (0x00) /*!< [15:8] sub2 version */ -#define __STM32F4xx_HAL_VERSION_RC (0x00) /*!< [7:0] release candidate */ -#define __STM32F4xx_HAL_VERSION ((__STM32F4xx_HAL_VERSION_MAIN << 24U)\ - |(__STM32F4xx_HAL_VERSION_SUB1 << 16U)\ - |(__STM32F4xx_HAL_VERSION_SUB2 << 8U )\ - |(__STM32F4xx_HAL_VERSION_RC)) + * @brief STM32F1xx HAL Driver version number V1.1.4 + */ +#define __STM32F1xx_HAL_VERSION_MAIN (0x01U) /*!< [31:24] main version */ +#define __STM32F1xx_HAL_VERSION_SUB1 (0x01U) /*!< [23:16] sub1 version */ +#define __STM32F1xx_HAL_VERSION_SUB2 (0x04U) /*!< [15:8] sub2 version */ +#define __STM32F1xx_HAL_VERSION_RC (0x00U) /*!< [7:0] release candidate */ +#define __STM32F1xx_HAL_VERSION ((__STM32F1xx_HAL_VERSION_MAIN << 24)\ + |(__STM32F1xx_HAL_VERSION_SUB1 << 16)\ + |(__STM32F1xx_HAL_VERSION_SUB2 << 8 )\ + |(__STM32F1xx_HAL_VERSION_RC)) -#define IDCODE_DEVID_MASK ((uint32_t)0x00000FFFU) +#define IDCODE_DEVID_MASK 0x00000FFFU -/* ------------ RCC registers bit address in the alias region ----------- */ -#define SYSCFG_OFFSET (SYSCFG_BASE - PERIPH_BASE) -/* --- MEMRMP Register ---*/ -/* Alias word address of UFB_MODE bit */ -#define MEMRMP_OFFSET SYSCFG_OFFSET -#define UFB_MODE_BIT_NUMBER POSITION_VAL(SYSCFG_MEMRMP_UFB_MODE) -#define UFB_MODE_BB (uint32_t)(PERIPH_BB_BASE + (MEMRMP_OFFSET * 32U) + (UFB_MODE_BIT_NUMBER * 4U)) - -/* --- CMPCR Register ---*/ -/* Alias word address of CMP_PD bit */ -#define CMPCR_OFFSET (SYSCFG_OFFSET + 0x20U) -#define CMP_PD_BIT_NUMBER POSITION_VAL(SYSCFG_CMPCR_CMP_PD) -#define CMPCR_CMP_PD_BB (uint32_t)(PERIPH_BB_BASE + (CMPCR_OFFSET * 32U) + (CMP_PD_BIT_NUMBER * 4U)) /** * @} */ /* Private macro -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ -/** @addtogroup HAL_Private_Variables + +/** @defgroup HAL_Private_Variables HAL Private Variables * @{ */ __IO uint32_t uwTick; +uint32_t uwTickPrio = (1UL << __NVIC_PRIO_BITS); /* Invalid PRIO */ +HAL_TickFreqTypeDef uwTickFreq = HAL_TICK_FREQ_DEFAULT; /* 1KHz */ /** * @} */ /* Private function prototypes -----------------------------------------------*/ -/* Private functions ---------------------------------------------------------*/ +/* Exported functions ---------------------------------------------------------*/ /** @defgroup HAL_Exported_Functions HAL Exported Functions * @{ @@ -121,14 +96,14 @@ __IO uint32_t uwTick; =============================================================================== ##### Initialization and de-initialization functions ##### =============================================================================== - [..] This section provides functions allowing to: - (+) Initializes the Flash interface the NVIC allocation and initial clock + [..] This section provides functions allowing to: + (+) Initializes the Flash interface, the NVIC allocation and initial clock configuration. It initializes the systick also when timeout is needed and the backup domain when enabled. - (+) de-Initializes common part of the HAL + (+) de-Initializes common part of the HAL. (+) Configure The time base source to have 1ms time base with a dedicated Tick interrupt priority. - (++) Systick timer is used by default as source of time base, but user + (++) SysTick timer is used by default as source of time base, but user can eventually implement his proper time base source (a general purpose timer for example or other time source), keeping in mind that Time base duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and @@ -151,13 +126,13 @@ __IO uint32_t uwTick; * @brief This function is used to initialize the HAL Library; it must be the first * instruction to be executed in the main program (before to call any other * HAL function), it performs the following: - * Configure the Flash prefetch, instruction and Data caches. + * Configure the Flash prefetch. * Configures the SysTick to generate an interrupt each 1 millisecond, * which is clocked by the HSI (at this stage, the clock is not yet * configured and thus the system is running from the internal HSI at 16 MHz). * Set NVIC Group Priority to 4. * Calls the HAL_MspInit() callback function defined in user file - * "stm32f4xx_hal_msp.c" to do the global low level hardware initialization + * "stm32f1xx_hal_msp.c" to do the global low level hardware initialization * * @note SysTick is used as time base for the HAL_Delay() function, the application * need to ensure that the SysTick time base is always set to 1 millisecond @@ -166,29 +141,35 @@ __IO uint32_t uwTick; */ HAL_StatusTypeDef HAL_Init(void) { - /* Configure Flash prefetch, Instruction cache, Data cache */ -#if (INSTRUCTION_CACHE_ENABLE != 0U) - __HAL_FLASH_INSTRUCTION_CACHE_ENABLE(); -#endif /* INSTRUCTION_CACHE_ENABLE */ -#if (DATA_CACHE_ENABLE != 0U) - __HAL_FLASH_DATA_CACHE_ENABLE(); -#endif /* DATA_CACHE_ENABLE */ -#if (PREFETCH_ENABLE != 0U) + /* Configure Flash prefetch */ +#if (PREFETCH_ENABLE != 0) +#if defined(STM32F101x6) || defined(STM32F101xB) || defined(STM32F101xE) || defined(STM32F101xG) || \ + defined(STM32F102x6) || defined(STM32F102xB) || \ + defined(STM32F103x6) || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG) || \ + defined(STM32F105xC) || defined(STM32F107xC) + + /* Prefetch buffer is not available on value line devices */ __HAL_FLASH_PREFETCH_BUFFER_ENABLE(); +#endif #endif /* PREFETCH_ENABLE */ + /* Set Interrupt Group Priority */ HAL_NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_4); + /* Use systick as time base source and configure 1ms tick (default clock after Reset is HSI) */ HAL_InitTick(TICK_INT_PRIORITY); + /* Init the low level hardware */ HAL_MspInit(); + /* Return function status */ return HAL_OK; } /** - * @brief This function de-Initializes common part of the HAL and stops the systick. - * This function is optional. + * @brief This function de-Initializes common part of the HAL and stops the systick. + * of time base. + * @note This function is optional. * @retval HAL status */ HAL_StatusTypeDef HAL_DeInit(void) @@ -196,27 +177,29 @@ HAL_StatusTypeDef HAL_DeInit(void) /* Reset of all peripherals */ __HAL_RCC_APB1_FORCE_RESET(); __HAL_RCC_APB1_RELEASE_RESET(); + __HAL_RCC_APB2_FORCE_RESET(); __HAL_RCC_APB2_RELEASE_RESET(); - __HAL_RCC_AHB1_FORCE_RESET(); - __HAL_RCC_AHB1_RELEASE_RESET(); - __HAL_RCC_AHB2_FORCE_RESET(); - __HAL_RCC_AHB2_RELEASE_RESET(); - __HAL_RCC_AHB3_FORCE_RESET(); - __HAL_RCC_AHB3_RELEASE_RESET(); + +#if defined(STM32F105xC) || defined(STM32F107xC) + __HAL_RCC_AHB_FORCE_RESET(); + __HAL_RCC_AHB_RELEASE_RESET(); +#endif + /* De-Init the low level hardware */ HAL_MspDeInit(); + /* Return function status */ return HAL_OK; } /** - * @brief Initializes the MSP. + * @brief Initialize the MSP. * @retval None */ __weak void HAL_MspInit(void) { - /* NOTE : This function Should not be modified, when the callback is needed, + /* NOTE : This function should not be modified, when the callback is needed, the HAL_MspInit could be implemented in the user file */ } @@ -227,7 +210,7 @@ __weak void HAL_MspInit(void) */ __weak void HAL_MspDeInit(void) { - /* NOTE : This function Should not be modified, when the callback is needed, + /* NOTE : This function should not be modified, when the callback is needed, the HAL_MspDeInit could be implemented in the user file */ } @@ -241,19 +224,32 @@ __weak void HAL_MspDeInit(void) * @note In the default implementation, SysTick timer is the source of time base. * It is used to generate interrupts at regular time intervals. * Care must be taken if HAL_Delay() is called from a peripheral ISR process, - * The the SysTick interrupt must have higher priority (numerically lower) + * The SysTick interrupt must have higher priority (numerically lower) * than the peripheral interrupt. Otherwise the caller ISR process will be blocked. * The function is declared as __weak to be overwritten in case of other * implementation in user file. - * @param TickPriority: Tick interrupt priority. + * @param TickPriority Tick interrupt priority. * @retval HAL status */ __weak HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority) { - /*Configure the SysTick to have interrupt in 1ms time basis*/ - HAL_SYSTICK_Config(SystemCoreClock / 1000U); - /*Configure the SysTick IRQ priority */ - HAL_NVIC_SetPriority(SysTick_IRQn, TickPriority, 0U); + /* Configure the SysTick to have interrupt in 1ms time basis*/ + if (HAL_SYSTICK_Config(SystemCoreClock / (1000U / uwTickFreq)) > 0U) + { + return HAL_ERROR; + } + + /* Configure the SysTick IRQ priority */ + if (TickPriority < (1UL << __NVIC_PRIO_BITS)) + { + HAL_NVIC_SetPriority(SysTick_IRQn, TickPriority, 0U); + uwTickPrio = TickPriority; + } + else + { + return HAL_ERROR; + } + /* Return function status */ return HAL_OK; } @@ -263,8 +259,8 @@ __weak HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority) */ /** @defgroup HAL_Exported_Functions_Group2 HAL Control functions - * @brief HAL Control functions - * + * @brief HAL Control functions + * @verbatim =============================================================================== ##### HAL Control functions ##### @@ -289,19 +285,19 @@ __weak HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority) * @brief This function is called to increment a global variable "uwTick" * used as application time base. * @note In the default implementation, this variable is incremented each 1ms - * in Systick ISR. - * @note This function is declared as __weak to be overwritten in case of other + * in SysTick ISR. + * @note This function is declared as __weak to be overwritten in case of other * implementations in user file. * @retval None */ __weak void HAL_IncTick(void) { - uwTick++; + uwTick += uwTickFreq; } /** * @brief Provides a tick value in millisecond. - * @note This function is declared as __weak to be overwritten in case of other + * @note This function is declared as __weak to be overwritten in case of other * implementations in user file. * @retval tick value */ @@ -311,22 +307,69 @@ __weak uint32_t HAL_GetTick(void) } /** - * @brief This function provides accurate delay (in milliseconds) based + * @brief This function returns a tick priority. + * @retval tick priority + */ +uint32_t HAL_GetTickPrio(void) +{ + return uwTickPrio; +} + +/** + * @brief Set new tick Freq. + * @retval status + */ +HAL_StatusTypeDef HAL_SetTickFreq(HAL_TickFreqTypeDef Freq) +{ + HAL_StatusTypeDef status = HAL_OK; + assert_param(IS_TICKFREQ(Freq)); + + if (uwTickFreq != Freq) + { + /* Apply the new tick Freq */ + status = HAL_InitTick(uwTickPrio); + + if (status == HAL_OK) + { + uwTickFreq = Freq; + } + } + + return status; +} + +/** + * @brief Return tick frequency. + * @retval tick period in Hz + */ +HAL_TickFreqTypeDef HAL_GetTickFreq(void) +{ + return uwTickFreq; +} + +/** + * @brief This function provides minimum delay (in milliseconds) based * on variable incremented. * @note In the default implementation , SysTick timer is the source of time base. * It is used to generate interrupts at regular time intervals where uwTick * is incremented. * @note This function is declared as __weak to be overwritten in case of other * implementations in user file. - * @param Delay: specifies the delay time length, in milliseconds. + * @param Delay specifies the delay time length, in milliseconds. * @retval None */ -__weak void HAL_Delay(__IO uint32_t Delay) +__weak void HAL_Delay(uint32_t Delay) { - uint32_t tickstart = 0U; - tickstart = HAL_GetTick(); + uint32_t tickstart = HAL_GetTick(); + uint32_t wait = Delay; + + /* Add a freq to guarantee minimum wait */ + if (wait < HAL_MAX_DELAY) + { + wait += (uint32_t)(uwTickFreq); + } - while ((HAL_GetTick() - tickstart) < Delay) + while ((HAL_GetTick() - tickstart) < wait) { } } @@ -344,7 +387,7 @@ __weak void HAL_Delay(__IO uint32_t Delay) __weak void HAL_SuspendTick(void) { /* Disable SysTick Interrupt */ - SysTick->CTRL &= ~SysTick_CTRL_TICKINT_Msk; + CLEAR_BIT(SysTick->CTRL, SysTick_CTRL_TICKINT_Msk); } /** @@ -360,29 +403,43 @@ __weak void HAL_SuspendTick(void) __weak void HAL_ResumeTick(void) { /* Enable SysTick Interrupt */ - SysTick->CTRL |= SysTick_CTRL_TICKINT_Msk; + SET_BIT(SysTick->CTRL, SysTick_CTRL_TICKINT_Msk); } /** * @brief Returns the HAL revision - * @retval version : 0xXYZR (8bits for each decimal, R for RC) + * @retval version 0xXYZR (8bits for each decimal, R for RC) */ uint32_t HAL_GetHalVersion(void) { - return __STM32F4xx_HAL_VERSION; + return __STM32F1xx_HAL_VERSION; } /** - * @brief Returns the device revision identifier. + * @brief Returns the device revision identifier. + * Note: On devices STM32F10xx8 and STM32F10xxB, + * STM32F101xC/D/E and STM32F103xC/D/E, + * STM32F101xF/G and STM32F103xF/G + * STM32F10xx4 and STM32F10xx6 + * Debug registers DBGMCU_IDCODE and DBGMCU_CR are accessible only in + * debug mode (not accessible by the user software in normal mode). + * Refer to errata sheet of these devices for more details. * @retval Device revision identifier */ uint32_t HAL_GetREVID(void) { - return ((DBGMCU->IDCODE) >> 16U); + return ((DBGMCU->IDCODE) >> DBGMCU_IDCODE_REV_ID_Pos); } /** * @brief Returns the device identifier. + * Note: On devices STM32F10xx8 and STM32F10xxB, + * STM32F101xC/D/E and STM32F103xC/D/E, + * STM32F101xF/G and STM32F103xF/G + * STM32F10xx4 and STM32F10xx6 + * Debug registers DBGMCU_IDCODE and DBGMCU_CR are accessible only in + * debug mode (not accessible by the user software in normal mode). + * Refer to errata sheet of these devices for more details. * @retval Device identifier */ uint32_t HAL_GetDEVID(void) @@ -390,6 +447,33 @@ uint32_t HAL_GetDEVID(void) return ((DBGMCU->IDCODE) & IDCODE_DEVID_MASK); } +/** + * @brief Returns first word of the unique device identifier (UID based on 96 bits) + * @retval Device identifier + */ +uint32_t HAL_GetUIDw0(void) +{ + return (READ_REG(*((uint32_t*)UID_BASE))); +} + +/** + * @brief Returns second word of the unique device identifier (UID based on 96 bits) + * @retval Device identifier + */ +uint32_t HAL_GetUIDw1(void) +{ + return (READ_REG(*((uint32_t*)(UID_BASE + 4U)))); +} + +/** + * @brief Returns third word of the unique device identifier (UID based on 96 bits) + * @retval Device identifier + */ +uint32_t HAL_GetUIDw2(void) +{ + return (READ_REG(*((uint32_t*)(UID_BASE + 8U)))); +} + /** * @brief Enable the Debug Module during SLEEP mode * @retval None @@ -401,6 +485,13 @@ void HAL_DBGMCU_EnableDBGSleepMode(void) /** * @brief Disable the Debug Module during SLEEP mode + * Note: On devices STM32F10xx8 and STM32F10xxB, + * STM32F101xC/D/E and STM32F103xC/D/E, + * STM32F101xF/G and STM32F103xF/G + * STM32F10xx4 and STM32F10xx6 + * Debug registers DBGMCU_IDCODE and DBGMCU_CR are accessible only in + * debug mode (not accessible by the user software in normal mode). + * Refer to errata sheet of these devices for more details. * @retval None */ void HAL_DBGMCU_DisableDBGSleepMode(void) @@ -410,6 +501,27 @@ void HAL_DBGMCU_DisableDBGSleepMode(void) /** * @brief Enable the Debug Module during STOP mode + * Note: On devices STM32F10xx8 and STM32F10xxB, + * STM32F101xC/D/E and STM32F103xC/D/E, + * STM32F101xF/G and STM32F103xF/G + * STM32F10xx4 and STM32F10xx6 + * Debug registers DBGMCU_IDCODE and DBGMCU_CR are accessible only in + * debug mode (not accessible by the user software in normal mode). + * Refer to errata sheet of these devices for more details. + * Note: On all STM32F1 devices: + * If the system tick timer interrupt is enabled during the Stop mode + * debug (DBG_STOP bit set in the DBGMCU_CR register ), it will wakeup + * the system from Stop mode. + * Workaround: To debug the Stop mode, disable the system tick timer + * interrupt. + * Refer to errata sheet of these devices for more details. + * Note: On all STM32F1 devices: + * If the system tick timer interrupt is enabled during the Stop mode + * debug (DBG_STOP bit set in the DBGMCU_CR register ), it will wakeup + * the system from Stop mode. + * Workaround: To debug the Stop mode, disable the system tick timer + * interrupt. + * Refer to errata sheet of these devices for more details. * @retval None */ void HAL_DBGMCU_EnableDBGStopMode(void) @@ -419,6 +531,13 @@ void HAL_DBGMCU_EnableDBGStopMode(void) /** * @brief Disable the Debug Module during STOP mode + * Note: On devices STM32F10xx8 and STM32F10xxB, + * STM32F101xC/D/E and STM32F103xC/D/E, + * STM32F101xF/G and STM32F103xF/G + * STM32F10xx4 and STM32F10xx6 + * Debug registers DBGMCU_IDCODE and DBGMCU_CR are accessible only in + * debug mode (not accessible by the user software in normal mode). + * Refer to errata sheet of these devices for more details. * @retval None */ void HAL_DBGMCU_DisableDBGStopMode(void) @@ -428,6 +547,13 @@ void HAL_DBGMCU_DisableDBGStopMode(void) /** * @brief Enable the Debug Module during STANDBY mode + * Note: On devices STM32F10xx8 and STM32F10xxB, + * STM32F101xC/D/E and STM32F103xC/D/E, + * STM32F101xF/G and STM32F103xF/G + * STM32F10xx4 and STM32F10xx6 + * Debug registers DBGMCU_IDCODE and DBGMCU_CR are accessible only in + * debug mode (not accessible by the user software in normal mode). + * Refer to errata sheet of these devices for more details. * @retval None */ void HAL_DBGMCU_EnableDBGStandbyMode(void) @@ -437,6 +563,13 @@ void HAL_DBGMCU_EnableDBGStandbyMode(void) /** * @brief Disable the Debug Module during STANDBY mode + * Note: On devices STM32F10xx8 and STM32F10xxB, + * STM32F101xC/D/E and STM32F103xC/D/E, + * STM32F101xF/G and STM32F103xF/G + * STM32F10xx4 and STM32F10xx6 + * Debug registers DBGMCU_IDCODE and DBGMCU_CR are accessible only in + * debug mode (not accessible by the user software in normal mode). + * Refer to errata sheet of these devices for more details. * @retval None */ void HAL_DBGMCU_DisableDBGStandbyMode(void) @@ -444,61 +577,6 @@ void HAL_DBGMCU_DisableDBGStandbyMode(void) CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STANDBY); } -/** - * @brief Enables the I/O Compensation Cell. - * @note The I/O compensation cell can be used only when the device supply - * voltage ranges from 2.4 to 3.6 V. - * @retval None - */ -void HAL_EnableCompensationCell(void) -{ - *(__IO uint32_t*)CMPCR_CMP_PD_BB = (uint32_t)ENABLE; -} - -/** - * @brief Power-down the I/O Compensation Cell. - * @note The I/O compensation cell can be used only when the device supply - * voltage ranges from 2.4 to 3.6 V. - * @retval None - */ -void HAL_DisableCompensationCell(void) -{ - *(__IO uint32_t*)CMPCR_CMP_PD_BB = (uint32_t)DISABLE; -} - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) ||\ - defined(STM32F469xx) || defined(STM32F479xx) -/** - * @brief Enables the Internal FLASH Bank Swapping. - * - * @note This function can be used only for STM32F42xxx/43xxx devices. - * - * @note Flash Bank2 mapped at 0x08000000 (and aliased @0x00000000) - * and Flash Bank1 mapped at 0x08100000 (and aliased at 0x00100000) - * - * @retval None - */ -void HAL_EnableMemorySwappingBank(void) -{ - *(__IO uint32_t*)UFB_MODE_BB = (uint32_t)ENABLE; -} - -/** - * @brief Disables the Internal FLASH Bank Swapping. - * - * @note This function can be used only for STM32F42xxx/43xxx devices. - * - * @note The default state : Flash Bank1 mapped at 0x08000000 (and aliased @0x00000000) - * and Flash Bank2 mapped at 0x08100000 (and aliased at 0x00100000) - * - * @retval None - */ -void HAL_DisableMemorySwappingBank(void) -{ - *(__IO uint32_t*)UFB_MODE_BB = (uint32_t)DISABLE; -} -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - /** * @} */ @@ -507,6 +585,7 @@ void HAL_DisableMemorySwappingBank(void) * @} */ +#endif /* HAL_MODULE_ENABLED */ /** * @} */ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_can.c b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_can.c new file mode 100644 index 00000000..2fac4442 --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_can.c @@ -0,0 +1,2450 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_can.c + * @author MCD Application Team + * @brief CAN HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Controller Area Network (CAN) peripheral: + * + Initialization and de-initialization functions + * + Configuration functions + * + Control functions + * + Interrupts management + * + Callbacks functions + * + Peripheral State and Error functions + * + @verbatim + ============================================================================== + ##### How to use this driver ##### + ============================================================================== + [..] + (#) Initialize the CAN low level resources by implementing the + HAL_CAN_MspInit(): + (++) Enable the CAN interface clock using __HAL_RCC_CANx_CLK_ENABLE() + (++) Configure CAN pins + (+++) Enable the clock for the CAN GPIOs + (+++) Configure CAN pins as alternate function open-drain + (++) In case of using interrupts (e.g. HAL_CAN_ActivateNotification()) + (+++) Configure the CAN interrupt priority using + HAL_NVIC_SetPriority() + (+++) Enable the CAN IRQ handler using HAL_NVIC_EnableIRQ() + (+++) In CAN IRQ handler, call HAL_CAN_IRQHandler() + + (#) Initialize the CAN peripheral using HAL_CAN_Init() function. This + function resorts to HAL_CAN_MspInit() for low-level initialization. + + (#) Configure the reception filters using the following configuration + functions: + (++) HAL_CAN_ConfigFilter() + + (#) Start the CAN module using HAL_CAN_Start() function. At this level + the node is active on the bus: it receive messages, and can send + messages. + + (#) To manage messages transmission, the following Tx control functions + can be used: + (++) HAL_CAN_AddTxMessage() to request transmission of a new + message. + (++) HAL_CAN_AbortTxRequest() to abort transmission of a pending + message. + (++) HAL_CAN_GetTxMailboxesFreeLevel() to get the number of free Tx + mailboxes. + (++) HAL_CAN_IsTxMessagePending() to check if a message is pending + in a Tx mailbox. + (++) HAL_CAN_GetTxTimestamp() to get the timestamp of Tx message + sent, if time triggered communication mode is enabled. + + (#) When a message is received into the CAN Rx FIFOs, it can be retrieved + using the HAL_CAN_GetRxMessage() function. The function + HAL_CAN_GetRxFifoFillLevel() allows to know how many Rx message are + stored in the Rx Fifo. + + (#) Calling the HAL_CAN_Stop() function stops the CAN module. + + (#) The deinitialization is achieved with HAL_CAN_DeInit() function. + + + *** Polling mode operation *** + ============================== + [..] + (#) Reception: + (++) Monitor reception of message using HAL_CAN_GetRxFifoFillLevel() + until at least one message is received. + (++) Then get the message using HAL_CAN_GetRxMessage(). + + (#) Transmission: + (++) Monitor the Tx mailboxes availability until at least one Tx + mailbox is free, using HAL_CAN_GetTxMailboxesFreeLevel(). + (++) Then request transmission of a message using + HAL_CAN_AddTxMessage(). + + + *** Interrupt mode operation *** + ================================ + [..] + (#) Notifications are activated using HAL_CAN_ActivateNotification() + function. Then, the process can be controlled through the + available user callbacks: HAL_CAN_xxxCallback(), using same APIs + HAL_CAN_GetRxMessage() and HAL_CAN_AddTxMessage(). + + (#) Notifications can be deactivated using + HAL_CAN_DeactivateNotification() function. + + (#) Special care should be taken for CAN_IT_RX_FIFO0_MSG_PENDING and + CAN_IT_RX_FIFO1_MSG_PENDING notifications. These notifications trig + the callbacks HAL_CAN_RxFIFO0MsgPendingCallback() and + HAL_CAN_RxFIFO1MsgPendingCallback(). User has two possible options + here. + (++) Directly get the Rx message in the callback, using + HAL_CAN_GetRxMessage(). + (++) Or deactivate the notification in the callback without + getting the Rx message. The Rx message can then be got later + using HAL_CAN_GetRxMessage(). Once the Rx message have been + read, the notification can be activated again. + + + *** Sleep mode *** + ================== + [..] + (#) The CAN peripheral can be put in sleep mode (low power), using + HAL_CAN_RequestSleep(). The sleep mode will be entered as soon as the + current CAN activity (transmission or reception of a CAN frame) will + be completed. + + (#) A notification can be activated to be informed when the sleep mode + will be entered. + + (#) It can be checked if the sleep mode is entered using + HAL_CAN_IsSleepActive(). + Note that the CAN state (accessible from the API HAL_CAN_GetState()) + is HAL_CAN_STATE_SLEEP_PENDING as soon as the sleep mode request is + submitted (the sleep mode is not yet entered), and become + HAL_CAN_STATE_SLEEP_ACTIVE when the sleep mode is effective. + + (#) The wake-up from sleep mode can be trigged by two ways: + (++) Using HAL_CAN_WakeUp(). When returning from this function, + the sleep mode is exited (if return status is HAL_OK). + (++) When a start of Rx CAN frame is detected by the CAN peripheral, + if automatic wake up mode is enabled. + + *** Callback registration *** + ============================================= + + The compilation define USE_HAL_CAN_REGISTER_CALLBACKS when set to 1 + allows the user to configure dynamically the driver callbacks. + Use Function @ref HAL_CAN_RegisterCallback() to register an interrupt callback. + + Function @ref HAL_CAN_RegisterCallback() allows to register following callbacks: + (+) TxMailbox0CompleteCallback : Tx Mailbox 0 Complete Callback. + (+) TxMailbox1CompleteCallback : Tx Mailbox 1 Complete Callback. + (+) TxMailbox2CompleteCallback : Tx Mailbox 2 Complete Callback. + (+) TxMailbox0AbortCallback : Tx Mailbox 0 Abort Callback. + (+) TxMailbox1AbortCallback : Tx Mailbox 1 Abort Callback. + (+) TxMailbox2AbortCallback : Tx Mailbox 2 Abort Callback. + (+) RxFifo0MsgPendingCallback : Rx Fifo 0 Message Pending Callback. + (+) RxFifo0FullCallback : Rx Fifo 0 Full Callback. + (+) RxFifo1MsgPendingCallback : Rx Fifo 1 Message Pending Callback. + (+) RxFifo1FullCallback : Rx Fifo 1 Full Callback. + (+) SleepCallback : Sleep Callback. + (+) WakeUpFromRxMsgCallback : Wake Up From Rx Message Callback. + (+) ErrorCallback : Error Callback. + (+) MspInitCallback : CAN MspInit. + (+) MspDeInitCallback : CAN MspDeInit. + This function takes as parameters the HAL peripheral handle, the Callback ID + and a pointer to the user callback function. + + Use function @ref HAL_CAN_UnRegisterCallback() to reset a callback to the default + weak function. + @ref HAL_CAN_UnRegisterCallback takes as parameters the HAL peripheral handle, + and the Callback ID. + This function allows to reset following callbacks: + (+) TxMailbox0CompleteCallback : Tx Mailbox 0 Complete Callback. + (+) TxMailbox1CompleteCallback : Tx Mailbox 1 Complete Callback. + (+) TxMailbox2CompleteCallback : Tx Mailbox 2 Complete Callback. + (+) TxMailbox0AbortCallback : Tx Mailbox 0 Abort Callback. + (+) TxMailbox1AbortCallback : Tx Mailbox 1 Abort Callback. + (+) TxMailbox2AbortCallback : Tx Mailbox 2 Abort Callback. + (+) RxFifo0MsgPendingCallback : Rx Fifo 0 Message Pending Callback. + (+) RxFifo0FullCallback : Rx Fifo 0 Full Callback. + (+) RxFifo1MsgPendingCallback : Rx Fifo 1 Message Pending Callback. + (+) RxFifo1FullCallback : Rx Fifo 1 Full Callback. + (+) SleepCallback : Sleep Callback. + (+) WakeUpFromRxMsgCallback : Wake Up From Rx Message Callback. + (+) ErrorCallback : Error Callback. + (+) MspInitCallback : CAN MspInit. + (+) MspDeInitCallback : CAN MspDeInit. + + By default, after the @ref HAL_CAN_Init() and when the state is HAL_CAN_STATE_RESET, + all callbacks are set to the corresponding weak functions: + example @ref HAL_CAN_ErrorCallback(). + Exception done for MspInit and MspDeInit functions that are + reset to the legacy weak function in the @ref HAL_CAN_Init()/ @ref HAL_CAN_DeInit() only when + these callbacks are null (not registered beforehand). + if not, MspInit or MspDeInit are not null, the @ref HAL_CAN_Init()/ @ref HAL_CAN_DeInit() + keep and use the user MspInit/MspDeInit callbacks (registered beforehand) + + Callbacks can be registered/unregistered in HAL_CAN_STATE_READY state only. + Exception done MspInit/MspDeInit that can be registered/unregistered + in HAL_CAN_STATE_READY or HAL_CAN_STATE_RESET state, + thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit. + In that case first register the MspInit/MspDeInit user callbacks + using @ref HAL_CAN_RegisterCallback() before calling @ref HAL_CAN_DeInit() + or @ref HAL_CAN_Init() function. + + When The compilation define USE_HAL_CAN_REGISTER_CALLBACKS is set to 0 or + not defined, the callback registration feature is not available and all callbacks + are set to the corresponding weak functions. + + @endverbatim + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +#if defined(CAN1) + +/** @defgroup CAN CAN + * @brief CAN driver modules + * @{ + */ + +#ifdef HAL_CAN_MODULE_ENABLED + +#ifdef HAL_CAN_LEGACY_MODULE_ENABLED +#error "The CAN driver cannot be used with its legacy, Please enable only one CAN module at once" +#endif + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/** @defgroup CAN_Private_Constants CAN Private Constants + * @{ + */ +#define CAN_TIMEOUT_VALUE 10U +/** + * @} + */ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Exported functions --------------------------------------------------------*/ + +/** @defgroup CAN_Exported_Functions CAN Exported Functions + * @{ + */ + +/** @defgroup CAN_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * +@verbatim + ============================================================================== + ##### Initialization and de-initialization functions ##### + ============================================================================== + [..] This section provides functions allowing to: + (+) HAL_CAN_Init : Initialize and configure the CAN. + (+) HAL_CAN_DeInit : De-initialize the CAN. + (+) HAL_CAN_MspInit : Initialize the CAN MSP. + (+) HAL_CAN_MspDeInit : DeInitialize the CAN MSP. + +@endverbatim + * @{ + */ + +/** + * @brief Initializes the CAN peripheral according to the specified + * parameters in the CAN_InitStruct. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CAN_Init(CAN_HandleTypeDef* hcan) +{ + uint32_t tickstart; + + /* Check CAN handle */ + if (hcan == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_CAN_ALL_INSTANCE(hcan->Instance)); + assert_param(IS_FUNCTIONAL_STATE(hcan->Init.TimeTriggeredMode)); + assert_param(IS_FUNCTIONAL_STATE(hcan->Init.AutoBusOff)); + assert_param(IS_FUNCTIONAL_STATE(hcan->Init.AutoWakeUp)); + assert_param(IS_FUNCTIONAL_STATE(hcan->Init.AutoRetransmission)); + assert_param(IS_FUNCTIONAL_STATE(hcan->Init.ReceiveFifoLocked)); + assert_param(IS_FUNCTIONAL_STATE(hcan->Init.TransmitFifoPriority)); + assert_param(IS_CAN_MODE(hcan->Init.Mode)); + assert_param(IS_CAN_SJW(hcan->Init.SyncJumpWidth)); + assert_param(IS_CAN_BS1(hcan->Init.TimeSeg1)); + assert_param(IS_CAN_BS2(hcan->Init.TimeSeg2)); + assert_param(IS_CAN_PRESCALER(hcan->Init.Prescaler)); + +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + + if (hcan->State == HAL_CAN_STATE_RESET) + { + /* Reset callbacks to legacy functions */ + hcan->RxFifo0MsgPendingCallback = HAL_CAN_RxFifo0MsgPendingCallback; /* Legacy weak RxFifo0MsgPendingCallback */ + hcan->RxFifo0FullCallback = HAL_CAN_RxFifo0FullCallback; /* Legacy weak RxFifo0FullCallback */ + hcan->RxFifo1MsgPendingCallback = HAL_CAN_RxFifo1MsgPendingCallback; /* Legacy weak RxFifo1MsgPendingCallback */ + hcan->RxFifo1FullCallback = HAL_CAN_RxFifo1FullCallback; /* Legacy weak RxFifo1FullCallback */ + hcan->TxMailbox0CompleteCallback = HAL_CAN_TxMailbox0CompleteCallback; /* Legacy weak TxMailbox0CompleteCallback */ + hcan->TxMailbox1CompleteCallback = HAL_CAN_TxMailbox1CompleteCallback; /* Legacy weak TxMailbox1CompleteCallback */ + hcan->TxMailbox2CompleteCallback = HAL_CAN_TxMailbox2CompleteCallback; /* Legacy weak TxMailbox2CompleteCallback */ + hcan->TxMailbox0AbortCallback = HAL_CAN_TxMailbox0AbortCallback; /* Legacy weak TxMailbox0AbortCallback */ + hcan->TxMailbox1AbortCallback = HAL_CAN_TxMailbox1AbortCallback; /* Legacy weak TxMailbox1AbortCallback */ + hcan->TxMailbox2AbortCallback = HAL_CAN_TxMailbox2AbortCallback; /* Legacy weak TxMailbox2AbortCallback */ + hcan->SleepCallback = HAL_CAN_SleepCallback; /* Legacy weak SleepCallback */ + hcan->WakeUpFromRxMsgCallback = HAL_CAN_WakeUpFromRxMsgCallback; /* Legacy weak WakeUpFromRxMsgCallback */ + hcan->ErrorCallback = HAL_CAN_ErrorCallback; /* Legacy weak ErrorCallback */ + + if (hcan->MspInitCallback == NULL) + { + hcan->MspInitCallback = HAL_CAN_MspInit; /* Legacy weak MspInit */ + } + + /* Init the low level hardware: CLOCK, NVIC */ + hcan->MspInitCallback(hcan); + } + +#else + + if (hcan->State == HAL_CAN_STATE_RESET) + { + /* Init the low level hardware: CLOCK, NVIC */ + HAL_CAN_MspInit(hcan); + } + +#endif /* (USE_HAL_CAN_REGISTER_CALLBACKS) */ + + /* Exit from sleep mode */ + CLEAR_BIT(hcan->Instance->MCR, CAN_MCR_SLEEP); + + /* Get tick */ + tickstart = HAL_GetTick(); + + /* Check Sleep mode leave acknowledge */ + while ((hcan->Instance->MSR & CAN_MSR_SLAK) != 0U) + { + if ((HAL_GetTick() - tickstart) > CAN_TIMEOUT_VALUE) + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_TIMEOUT; + + /* Change CAN state */ + hcan->State = HAL_CAN_STATE_ERROR; + + return HAL_ERROR; + } + } + + /* Request initialisation */ + SET_BIT(hcan->Instance->MCR, CAN_MCR_INRQ); + + /* Get tick */ + tickstart = HAL_GetTick(); + + /* Wait initialisation acknowledge */ + while ((hcan->Instance->MSR & CAN_MSR_INAK) == 0U) + { + if ((HAL_GetTick() - tickstart) > CAN_TIMEOUT_VALUE) + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_TIMEOUT; + + /* Change CAN state */ + hcan->State = HAL_CAN_STATE_ERROR; + + return HAL_ERROR; + } + } + + /* Set the time triggered communication mode */ + if (hcan->Init.TimeTriggeredMode == ENABLE) + { + SET_BIT(hcan->Instance->MCR, CAN_MCR_TTCM); + } + else + { + CLEAR_BIT(hcan->Instance->MCR, CAN_MCR_TTCM); + } + + /* Set the automatic bus-off management */ + if (hcan->Init.AutoBusOff == ENABLE) + { + SET_BIT(hcan->Instance->MCR, CAN_MCR_ABOM); + } + else + { + CLEAR_BIT(hcan->Instance->MCR, CAN_MCR_ABOM); + } + + /* Set the automatic wake-up mode */ + if (hcan->Init.AutoWakeUp == ENABLE) + { + SET_BIT(hcan->Instance->MCR, CAN_MCR_AWUM); + } + else + { + CLEAR_BIT(hcan->Instance->MCR, CAN_MCR_AWUM); + } + + /* Set the automatic retransmission */ + if (hcan->Init.AutoRetransmission == ENABLE) + { + CLEAR_BIT(hcan->Instance->MCR, CAN_MCR_NART); + } + else + { + SET_BIT(hcan->Instance->MCR, CAN_MCR_NART); + } + + /* Set the receive FIFO locked mode */ + if (hcan->Init.ReceiveFifoLocked == ENABLE) + { + SET_BIT(hcan->Instance->MCR, CAN_MCR_RFLM); + } + else + { + CLEAR_BIT(hcan->Instance->MCR, CAN_MCR_RFLM); + } + + /* Set the transmit FIFO priority */ + if (hcan->Init.TransmitFifoPriority == ENABLE) + { + SET_BIT(hcan->Instance->MCR, CAN_MCR_TXFP); + } + else + { + CLEAR_BIT(hcan->Instance->MCR, CAN_MCR_TXFP); + } + + /* Set the bit timing register */ + WRITE_REG(hcan->Instance->BTR, (uint32_t)(hcan->Init.Mode | + hcan->Init.SyncJumpWidth | + hcan->Init.TimeSeg1 | + hcan->Init.TimeSeg2 | + (hcan->Init.Prescaler - 1U))); + + /* Initialize the error code */ + hcan->ErrorCode = HAL_CAN_ERROR_NONE; + + /* Initialize the CAN state */ + hcan->State = HAL_CAN_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Deinitializes the CAN peripheral registers to their default + * reset values. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CAN_DeInit(CAN_HandleTypeDef* hcan) +{ + /* Check CAN handle */ + if (hcan == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_CAN_ALL_INSTANCE(hcan->Instance)); + + /* Stop the CAN module */ + (void)HAL_CAN_Stop(hcan); + +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + + if (hcan->MspDeInitCallback == NULL) + { + hcan->MspDeInitCallback = HAL_CAN_MspDeInit; /* Legacy weak MspDeInit */ + } + + /* DeInit the low level hardware: CLOCK, NVIC */ + hcan->MspDeInitCallback(hcan); + +#else + /* DeInit the low level hardware: CLOCK, NVIC */ + HAL_CAN_MspDeInit(hcan); +#endif /* (USE_HAL_CAN_REGISTER_CALLBACKS) */ + + /* Reset the CAN peripheral */ + SET_BIT(hcan->Instance->MCR, CAN_MCR_RESET); + + /* Reset the CAN ErrorCode */ + hcan->ErrorCode = HAL_CAN_ERROR_NONE; + + /* Change CAN state */ + hcan->State = HAL_CAN_STATE_RESET; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Initializes the CAN MSP. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +__weak void HAL_CAN_MspInit(CAN_HandleTypeDef* hcan) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hcan); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CAN_MspInit could be implemented in the user file + */ +} + +/** + * @brief DeInitializes the CAN MSP. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +__weak void HAL_CAN_MspDeInit(CAN_HandleTypeDef* hcan) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hcan); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CAN_MspDeInit could be implemented in the user file + */ +} + +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 +/** + * @brief Register a CAN CallBack. + * To be used instead of the weak predefined callback + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for CAN module + * @param CallbackID ID of the callback to be registered + * This parameter can be one of the following values: + * @arg @ref HAL_CAN_TX_MAILBOX0_COMPLETE_CALLBACK_CB_ID Tx Mailbox 0 Complete callback ID + * @arg @ref HAL_CAN_TX_MAILBOX1_COMPLETE_CALLBACK_CB_ID Tx Mailbox 1 Complete callback ID + * @arg @ref HAL_CAN_TX_MAILBOX2_COMPLETE_CALLBACK_CB_ID Tx Mailbox 2 Complete callback ID + * @arg @ref HAL_CAN_TX_MAILBOX0_ABORT_CALLBACK_CB_ID Tx Mailbox 0 Abort callback ID + * @arg @ref HAL_CAN_TX_MAILBOX1_ABORT_CALLBACK_CB_ID Tx Mailbox 1 Abort callback ID + * @arg @ref HAL_CAN_TX_MAILBOX2_ABORT_CALLBACK_CB_ID Tx Mailbox 2 Abort callback ID + * @arg @ref HAL_CAN_RX_FIFO0_MSG_PENDING_CALLBACK_CB_ID Rx Fifo 0 message pending callback ID + * @arg @ref HAL_CAN_RX_FIFO0_FULL_CALLBACK_CB_ID Rx Fifo 0 full callback ID + * @arg @ref HAL_CAN_RX_FIFO1_MSGPENDING_CALLBACK_CB_ID Rx Fifo 1 message pending callback ID + * @arg @ref HAL_CAN_RX_FIFO1_FULL_CALLBACK_CB_ID Rx Fifo 1 full callback ID + * @arg @ref HAL_CAN_SLEEP_CALLBACK_CB_ID Sleep callback ID + * @arg @ref HAL_CAN_WAKEUP_FROM_RX_MSG_CALLBACK_CB_ID Wake Up from Rx message callback ID + * @arg @ref HAL_CAN_ERROR_CALLBACK_CB_ID Error callback ID + * @arg @ref HAL_CAN_MSPINIT_CB_ID MspInit callback ID + * @arg @ref HAL_CAN_MSPDEINIT_CB_ID MspDeInit callback ID + * @param pCallback pointer to the Callback function + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CAN_RegisterCallback(CAN_HandleTypeDef* hcan, HAL_CAN_CallbackIDTypeDef CallbackID, void (* pCallback)(CAN_HandleTypeDef* _hcan)) +{ + HAL_StatusTypeDef status = HAL_OK; + + if (pCallback == NULL) + { + /* Update the error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_INVALID_CALLBACK; + + return HAL_ERROR; + } + + if (hcan->State == HAL_CAN_STATE_READY) + { + switch (CallbackID) + { + case HAL_CAN_TX_MAILBOX0_COMPLETE_CB_ID : + hcan->TxMailbox0CompleteCallback = pCallback; + break; + + case HAL_CAN_TX_MAILBOX1_COMPLETE_CB_ID : + hcan->TxMailbox1CompleteCallback = pCallback; + break; + + case HAL_CAN_TX_MAILBOX2_COMPLETE_CB_ID : + hcan->TxMailbox2CompleteCallback = pCallback; + break; + + case HAL_CAN_TX_MAILBOX0_ABORT_CB_ID : + hcan->TxMailbox0AbortCallback = pCallback; + break; + + case HAL_CAN_TX_MAILBOX1_ABORT_CB_ID : + hcan->TxMailbox1AbortCallback = pCallback; + break; + + case HAL_CAN_TX_MAILBOX2_ABORT_CB_ID : + hcan->TxMailbox2AbortCallback = pCallback; + break; + + case HAL_CAN_RX_FIFO0_MSG_PENDING_CB_ID : + hcan->RxFifo0MsgPendingCallback = pCallback; + break; + + case HAL_CAN_RX_FIFO0_FULL_CB_ID : + hcan->RxFifo0FullCallback = pCallback; + break; + + case HAL_CAN_RX_FIFO1_MSG_PENDING_CB_ID : + hcan->RxFifo1MsgPendingCallback = pCallback; + break; + + case HAL_CAN_RX_FIFO1_FULL_CB_ID : + hcan->RxFifo1FullCallback = pCallback; + break; + + case HAL_CAN_SLEEP_CB_ID : + hcan->SleepCallback = pCallback; + break; + + case HAL_CAN_WAKEUP_FROM_RX_MSG_CB_ID : + hcan->WakeUpFromRxMsgCallback = pCallback; + break; + + case HAL_CAN_ERROR_CB_ID : + hcan->ErrorCallback = pCallback; + break; + + case HAL_CAN_MSPINIT_CB_ID : + hcan->MspInitCallback = pCallback; + break; + + case HAL_CAN_MSPDEINIT_CB_ID : + hcan->MspDeInitCallback = pCallback; + break; + + default : + /* Update the error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + break; + } + } + else if (hcan->State == HAL_CAN_STATE_RESET) + { + switch (CallbackID) + { + case HAL_CAN_MSPINIT_CB_ID : + hcan->MspInitCallback = pCallback; + break; + + case HAL_CAN_MSPDEINIT_CB_ID : + hcan->MspDeInitCallback = pCallback; + break; + + default : + /* Update the error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + break; + } + } + else + { + /* Update the error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + } + + return status; +} + +/** + * @brief Unregister a CAN CallBack. + * CAN callabck is redirected to the weak predefined callback + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for CAN module + * @param CallbackID ID of the callback to be unregistered + * This parameter can be one of the following values: + * @arg @ref HAL_CAN_TX_MAILBOX0_COMPLETE_CALLBACK_CB_ID Tx Mailbox 0 Complete callback ID + * @arg @ref HAL_CAN_TX_MAILBOX1_COMPLETE_CALLBACK_CB_ID Tx Mailbox 1 Complete callback ID + * @arg @ref HAL_CAN_TX_MAILBOX2_COMPLETE_CALLBACK_CB_ID Tx Mailbox 2 Complete callback ID + * @arg @ref HAL_CAN_TX_MAILBOX0_ABORT_CALLBACK_CB_ID Tx Mailbox 0 Abort callback ID + * @arg @ref HAL_CAN_TX_MAILBOX1_ABORT_CALLBACK_CB_ID Tx Mailbox 1 Abort callback ID + * @arg @ref HAL_CAN_TX_MAILBOX2_ABORT_CALLBACK_CB_ID Tx Mailbox 2 Abort callback ID + * @arg @ref HAL_CAN_RX_FIFO0_MSG_PENDING_CALLBACK_CB_ID Rx Fifo 0 message pending callback ID + * @arg @ref HAL_CAN_RX_FIFO0_FULL_CALLBACK_CB_ID Rx Fifo 0 full callback ID + * @arg @ref HAL_CAN_RX_FIFO1_MSGPENDING_CALLBACK_CB_ID Rx Fifo 1 message pending callback ID + * @arg @ref HAL_CAN_RX_FIFO1_FULL_CALLBACK_CB_ID Rx Fifo 1 full callback ID + * @arg @ref HAL_CAN_SLEEP_CALLBACK_CB_ID Sleep callback ID + * @arg @ref HAL_CAN_WAKEUP_FROM_RX_MSG_CALLBACK_CB_ID Wake Up from Rx message callback ID + * @arg @ref HAL_CAN_ERROR_CALLBACK_CB_ID Error callback ID + * @arg @ref HAL_CAN_MSPINIT_CB_ID MspInit callback ID + * @arg @ref HAL_CAN_MSPDEINIT_CB_ID MspDeInit callback ID + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CAN_UnRegisterCallback(CAN_HandleTypeDef* hcan, HAL_CAN_CallbackIDTypeDef CallbackID) +{ + HAL_StatusTypeDef status = HAL_OK; + + if (hcan->State == HAL_CAN_STATE_READY) + { + switch (CallbackID) + { + case HAL_CAN_TX_MAILBOX0_COMPLETE_CB_ID : + hcan->TxMailbox0CompleteCallback = HAL_CAN_TxMailbox0CompleteCallback; + break; + + case HAL_CAN_TX_MAILBOX1_COMPLETE_CB_ID : + hcan->TxMailbox1CompleteCallback = HAL_CAN_TxMailbox1CompleteCallback; + break; + + case HAL_CAN_TX_MAILBOX2_COMPLETE_CB_ID : + hcan->TxMailbox2CompleteCallback = HAL_CAN_TxMailbox2CompleteCallback; + break; + + case HAL_CAN_TX_MAILBOX0_ABORT_CB_ID : + hcan->TxMailbox0AbortCallback = HAL_CAN_TxMailbox0AbortCallback; + break; + + case HAL_CAN_TX_MAILBOX1_ABORT_CB_ID : + hcan->TxMailbox1AbortCallback = HAL_CAN_TxMailbox1AbortCallback; + break; + + case HAL_CAN_TX_MAILBOX2_ABORT_CB_ID : + hcan->TxMailbox2AbortCallback = HAL_CAN_TxMailbox2AbortCallback; + break; + + case HAL_CAN_RX_FIFO0_MSG_PENDING_CB_ID : + hcan->RxFifo0MsgPendingCallback = HAL_CAN_RxFifo0MsgPendingCallback; + break; + + case HAL_CAN_RX_FIFO0_FULL_CB_ID : + hcan->RxFifo0FullCallback = HAL_CAN_RxFifo0FullCallback; + break; + + case HAL_CAN_RX_FIFO1_MSG_PENDING_CB_ID : + hcan->RxFifo1MsgPendingCallback = HAL_CAN_RxFifo1MsgPendingCallback; + break; + + case HAL_CAN_RX_FIFO1_FULL_CB_ID : + hcan->RxFifo1FullCallback = HAL_CAN_RxFifo1FullCallback; + break; + + case HAL_CAN_SLEEP_CB_ID : + hcan->SleepCallback = HAL_CAN_SleepCallback; + break; + + case HAL_CAN_WAKEUP_FROM_RX_MSG_CB_ID : + hcan->WakeUpFromRxMsgCallback = HAL_CAN_WakeUpFromRxMsgCallback; + break; + + case HAL_CAN_ERROR_CB_ID : + hcan->ErrorCallback = HAL_CAN_ErrorCallback; + break; + + case HAL_CAN_MSPINIT_CB_ID : + hcan->MspInitCallback = HAL_CAN_MspInit; + break; + + case HAL_CAN_MSPDEINIT_CB_ID : + hcan->MspDeInitCallback = HAL_CAN_MspDeInit; + break; + + default : + /* Update the error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + break; + } + } + else if (hcan->State == HAL_CAN_STATE_RESET) + { + switch (CallbackID) + { + case HAL_CAN_MSPINIT_CB_ID : + hcan->MspInitCallback = HAL_CAN_MspInit; + break; + + case HAL_CAN_MSPDEINIT_CB_ID : + hcan->MspDeInitCallback = HAL_CAN_MspDeInit; + break; + + default : + /* Update the error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + break; + } + } + else + { + /* Update the error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + } + + return status; +} +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ + +/** + * @} + */ + +/** @defgroup CAN_Exported_Functions_Group2 Configuration functions + * @brief Configuration functions. + * +@verbatim + ============================================================================== + ##### Configuration functions ##### + ============================================================================== + [..] This section provides functions allowing to: + (+) HAL_CAN_ConfigFilter : Configure the CAN reception filters + +@endverbatim + * @{ + */ + +/** + * @brief Configures the CAN reception filter according to the specified + * parameters in the CAN_FilterInitStruct. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @param sFilterConfig pointer to a CAN_FilterTypeDef structure that + * contains the filter configuration information. + * @retval None + */ +HAL_StatusTypeDef HAL_CAN_ConfigFilter(CAN_HandleTypeDef* hcan, CAN_FilterTypeDef* sFilterConfig) +{ + uint32_t filternbrbitpos; + CAN_TypeDef* can_ip = hcan->Instance; + HAL_CAN_StateTypeDef state = hcan->State; + + if ((state == HAL_CAN_STATE_READY) || + (state == HAL_CAN_STATE_LISTENING)) + { + /* Check the parameters */ + assert_param(IS_CAN_FILTER_ID_HALFWORD(sFilterConfig->FilterIdHigh)); + assert_param(IS_CAN_FILTER_ID_HALFWORD(sFilterConfig->FilterIdLow)); + assert_param(IS_CAN_FILTER_ID_HALFWORD(sFilterConfig->FilterMaskIdHigh)); + assert_param(IS_CAN_FILTER_ID_HALFWORD(sFilterConfig->FilterMaskIdLow)); + assert_param(IS_CAN_FILTER_MODE(sFilterConfig->FilterMode)); + assert_param(IS_CAN_FILTER_SCALE(sFilterConfig->FilterScale)); + assert_param(IS_CAN_FILTER_FIFO(sFilterConfig->FilterFIFOAssignment)); + assert_param(IS_CAN_FILTER_ACTIVATION(sFilterConfig->FilterActivation)); + +#if defined(CAN2) + /* CAN1 and CAN2 are dual instances with 28 common filters banks */ + /* Select master instance to access the filter banks */ + can_ip = CAN1; + + /* Check the parameters */ + assert_param(IS_CAN_FILTER_BANK_DUAL(sFilterConfig->FilterBank)); + assert_param(IS_CAN_FILTER_BANK_DUAL(sFilterConfig->SlaveStartFilterBank)); +#else + /* CAN1 is single instance with 14 dedicated filters banks */ + + /* Check the parameters */ + assert_param(IS_CAN_FILTER_BANK_SINGLE(sFilterConfig->FilterBank)); +#endif + + /* Initialisation mode for the filter */ + SET_BIT(can_ip->FMR, CAN_FMR_FINIT); + +#if defined(CAN2) + /* Select the start filter number of CAN2 slave instance */ + CLEAR_BIT(can_ip->FMR, CAN_FMR_CAN2SB); + SET_BIT(can_ip->FMR, sFilterConfig->SlaveStartFilterBank << CAN_FMR_CAN2SB_Pos); + +#endif + /* Convert filter number into bit position */ + filternbrbitpos = (uint32_t)1 << (sFilterConfig->FilterBank & 0x1FU); + + /* Filter Deactivation */ + CLEAR_BIT(can_ip->FA1R, filternbrbitpos); + + /* Filter Scale */ + if (sFilterConfig->FilterScale == CAN_FILTERSCALE_16BIT) + { + /* 16-bit scale for the filter */ + CLEAR_BIT(can_ip->FS1R, filternbrbitpos); + + /* First 16-bit identifier and First 16-bit mask */ + /* Or First 16-bit identifier and Second 16-bit identifier */ + can_ip->sFilterRegister[sFilterConfig->FilterBank].FR1 = + ((0x0000FFFFU & (uint32_t)sFilterConfig->FilterMaskIdLow) << 16U) | + (0x0000FFFFU & (uint32_t)sFilterConfig->FilterIdLow); + + /* Second 16-bit identifier and Second 16-bit mask */ + /* Or Third 16-bit identifier and Fourth 16-bit identifier */ + can_ip->sFilterRegister[sFilterConfig->FilterBank].FR2 = + ((0x0000FFFFU & (uint32_t)sFilterConfig->FilterMaskIdHigh) << 16U) | + (0x0000FFFFU & (uint32_t)sFilterConfig->FilterIdHigh); + } + + if (sFilterConfig->FilterScale == CAN_FILTERSCALE_32BIT) + { + /* 32-bit scale for the filter */ + SET_BIT(can_ip->FS1R, filternbrbitpos); + + /* 32-bit identifier or First 32-bit identifier */ + can_ip->sFilterRegister[sFilterConfig->FilterBank].FR1 = + ((0x0000FFFFU & (uint32_t)sFilterConfig->FilterIdHigh) << 16U) | + (0x0000FFFFU & (uint32_t)sFilterConfig->FilterIdLow); + + /* 32-bit mask or Second 32-bit identifier */ + can_ip->sFilterRegister[sFilterConfig->FilterBank].FR2 = + ((0x0000FFFFU & (uint32_t)sFilterConfig->FilterMaskIdHigh) << 16U) | + (0x0000FFFFU & (uint32_t)sFilterConfig->FilterMaskIdLow); + } + + /* Filter Mode */ + if (sFilterConfig->FilterMode == CAN_FILTERMODE_IDMASK) + { + /* Id/Mask mode for the filter*/ + CLEAR_BIT(can_ip->FM1R, filternbrbitpos); + } + else /* CAN_FilterInitStruct->CAN_FilterMode == CAN_FilterMode_IdList */ + { + /* Identifier list mode for the filter*/ + SET_BIT(can_ip->FM1R, filternbrbitpos); + } + + /* Filter FIFO assignment */ + if (sFilterConfig->FilterFIFOAssignment == CAN_FILTER_FIFO0) + { + /* FIFO 0 assignation for the filter */ + CLEAR_BIT(can_ip->FFA1R, filternbrbitpos); + } + else + { + /* FIFO 1 assignation for the filter */ + SET_BIT(can_ip->FFA1R, filternbrbitpos); + } + + /* Filter activation */ + if (sFilterConfig->FilterActivation == CAN_FILTER_ENABLE) + { + SET_BIT(can_ip->FA1R, filternbrbitpos); + } + + /* Leave the initialisation mode for the filter */ + CLEAR_BIT(can_ip->FMR, CAN_FMR_FINIT); + + /* Return function status */ + return HAL_OK; + } + else + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_NOT_INITIALIZED; + + return HAL_ERROR; + } +} + +/** + * @} + */ + +/** @defgroup CAN_Exported_Functions_Group3 Control functions + * @brief Control functions + * +@verbatim + ============================================================================== + ##### Control functions ##### + ============================================================================== + [..] This section provides functions allowing to: + (+) HAL_CAN_Start : Start the CAN module + (+) HAL_CAN_Stop : Stop the CAN module + (+) HAL_CAN_RequestSleep : Request sleep mode entry. + (+) HAL_CAN_WakeUp : Wake up from sleep mode. + (+) HAL_CAN_IsSleepActive : Check is sleep mode is active. + (+) HAL_CAN_AddTxMessage : Add a message to the Tx mailboxes + and activate the corresponding + transmission request + (+) HAL_CAN_AbortTxRequest : Abort transmission request + (+) HAL_CAN_GetTxMailboxesFreeLevel : Return Tx mailboxes free level + (+) HAL_CAN_IsTxMessagePending : Check if a transmission request is + pending on the selected Tx mailbox + (+) HAL_CAN_GetRxMessage : Get a CAN frame from the Rx FIFO + (+) HAL_CAN_GetRxFifoFillLevel : Return Rx FIFO fill level + +@endverbatim + * @{ + */ + +/** + * @brief Start the CAN module. + * @param hcan pointer to an CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CAN_Start(CAN_HandleTypeDef* hcan) +{ + uint32_t tickstart; + + if (hcan->State == HAL_CAN_STATE_READY) + { + /* Change CAN peripheral state */ + hcan->State = HAL_CAN_STATE_LISTENING; + + /* Request leave initialisation */ + CLEAR_BIT(hcan->Instance->MCR, CAN_MCR_INRQ); + + /* Get tick */ + tickstart = HAL_GetTick(); + + /* Wait the acknowledge */ + while ((hcan->Instance->MSR & CAN_MSR_INAK) != 0U) + { + /* Check for the Timeout */ + if ((HAL_GetTick() - tickstart) > CAN_TIMEOUT_VALUE) + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_TIMEOUT; + + /* Change CAN state */ + hcan->State = HAL_CAN_STATE_ERROR; + + return HAL_ERROR; + } + } + + /* Reset the CAN ErrorCode */ + hcan->ErrorCode = HAL_CAN_ERROR_NONE; + + /* Return function status */ + return HAL_OK; + } + else + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_NOT_READY; + + return HAL_ERROR; + } +} + +/** + * @brief Stop the CAN module and enable access to configuration registers. + * @param hcan pointer to an CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CAN_Stop(CAN_HandleTypeDef* hcan) +{ + uint32_t tickstart; + + if (hcan->State == HAL_CAN_STATE_LISTENING) + { + /* Request initialisation */ + SET_BIT(hcan->Instance->MCR, CAN_MCR_INRQ); + + /* Get tick */ + tickstart = HAL_GetTick(); + + /* Wait the acknowledge */ + while ((hcan->Instance->MSR & CAN_MSR_INAK) == 0U) + { + /* Check for the Timeout */ + if ((HAL_GetTick() - tickstart) > CAN_TIMEOUT_VALUE) + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_TIMEOUT; + + /* Change CAN state */ + hcan->State = HAL_CAN_STATE_ERROR; + + return HAL_ERROR; + } + } + + /* Exit from sleep mode */ + CLEAR_BIT(hcan->Instance->MCR, CAN_MCR_SLEEP); + + /* Change CAN peripheral state */ + hcan->State = HAL_CAN_STATE_READY; + + /* Return function status */ + return HAL_OK; + } + else + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_NOT_STARTED; + + return HAL_ERROR; + } +} + +/** + * @brief Request the sleep mode (low power) entry. + * When returning from this function, Sleep mode will be entered + * as soon as the current CAN activity (transmission or reception + * of a CAN frame) has been completed. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval HAL status. + */ +HAL_StatusTypeDef HAL_CAN_RequestSleep(CAN_HandleTypeDef* hcan) +{ + HAL_CAN_StateTypeDef state = hcan->State; + + if ((state == HAL_CAN_STATE_READY) || + (state == HAL_CAN_STATE_LISTENING)) + { + /* Request Sleep mode */ + SET_BIT(hcan->Instance->MCR, CAN_MCR_SLEEP); + + /* Return function status */ + return HAL_OK; + } + else + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_NOT_INITIALIZED; + + /* Return function status */ + return HAL_ERROR; + } +} + +/** + * @brief Wake up from sleep mode. + * When returning with HAL_OK status from this function, Sleep mode + * is exited. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval HAL status. + */ +HAL_StatusTypeDef HAL_CAN_WakeUp(CAN_HandleTypeDef* hcan) +{ + __IO uint32_t count = 0; + uint32_t timeout = 1000000U; + HAL_CAN_StateTypeDef state = hcan->State; + + if ((state == HAL_CAN_STATE_READY) || + (state == HAL_CAN_STATE_LISTENING)) + { + /* Wake up request */ + CLEAR_BIT(hcan->Instance->MCR, CAN_MCR_SLEEP); + + /* Wait sleep mode is exited */ + do + { + /* Increment counter */ + count++; + + /* Check if timeout is reached */ + if (count > timeout) + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_TIMEOUT; + + return HAL_ERROR; + } + } + while ((hcan->Instance->MSR & CAN_MSR_SLAK) != 0U); + + /* Return function status */ + return HAL_OK; + } + else + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_NOT_INITIALIZED; + + return HAL_ERROR; + } +} + +/** + * @brief Check is sleep mode is active. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval Status + * - 0 : Sleep mode is not active. + * - 1 : Sleep mode is active. + */ +uint32_t HAL_CAN_IsSleepActive(CAN_HandleTypeDef* hcan) +{ + uint32_t status = 0U; + HAL_CAN_StateTypeDef state = hcan->State; + + if ((state == HAL_CAN_STATE_READY) || + (state == HAL_CAN_STATE_LISTENING)) + { + /* Check Sleep mode */ + if ((hcan->Instance->MSR & CAN_MSR_SLAK) != 0U) + { + status = 1U; + } + } + + /* Return function status */ + return status; +} + +/** + * @brief Add a message to the first free Tx mailbox and activate the + * corresponding transmission request. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @param pHeader pointer to a CAN_TxHeaderTypeDef structure. + * @param aData array containing the payload of the Tx frame. + * @param pTxMailbox pointer to a variable where the function will return + * the TxMailbox used to store the Tx message. + * This parameter can be a value of @arg CAN_Tx_Mailboxes. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CAN_AddTxMessage(CAN_HandleTypeDef* hcan, CAN_TxHeaderTypeDef* pHeader, uint8_t aData[], uint32_t* pTxMailbox) +{ + uint32_t transmitmailbox; + HAL_CAN_StateTypeDef state = hcan->State; + uint32_t tsr = READ_REG(hcan->Instance->TSR); + + /* Check the parameters */ + assert_param(IS_CAN_IDTYPE(pHeader->IDE)); + assert_param(IS_CAN_RTR(pHeader->RTR)); + assert_param(IS_CAN_DLC(pHeader->DLC)); + + if (pHeader->IDE == CAN_ID_STD) + { + assert_param(IS_CAN_STDID(pHeader->StdId)); + } + else + { + assert_param(IS_CAN_EXTID(pHeader->ExtId)); + } + + assert_param(IS_FUNCTIONAL_STATE(pHeader->TransmitGlobalTime)); + + if ((state == HAL_CAN_STATE_READY) || + (state == HAL_CAN_STATE_LISTENING)) + { + /* Check that all the Tx mailboxes are not full */ + if (((tsr & CAN_TSR_TME0) != 0U) || + ((tsr & CAN_TSR_TME1) != 0U) || + ((tsr & CAN_TSR_TME2) != 0U)) + { + /* Select an empty transmit mailbox */ + transmitmailbox = (tsr & CAN_TSR_CODE) >> CAN_TSR_CODE_Pos; + + /* Check transmit mailbox value */ + if (transmitmailbox > 2U) + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_INTERNAL; + + return HAL_ERROR; + } + + /* Store the Tx mailbox */ + *pTxMailbox = (uint32_t)1 << transmitmailbox; + + /* Set up the Id */ + if (pHeader->IDE == CAN_ID_STD) + { + hcan->Instance->sTxMailBox[transmitmailbox].TIR = ((pHeader->StdId << CAN_TI0R_STID_Pos) | + pHeader->RTR); + } + else + { + hcan->Instance->sTxMailBox[transmitmailbox].TIR = ((pHeader->ExtId << CAN_TI0R_EXID_Pos) | + pHeader->IDE | + pHeader->RTR); + } + + /* Set up the DLC */ + hcan->Instance->sTxMailBox[transmitmailbox].TDTR = (pHeader->DLC); + + /* Set up the Transmit Global Time mode */ + if (pHeader->TransmitGlobalTime == ENABLE) + { + SET_BIT(hcan->Instance->sTxMailBox[transmitmailbox].TDTR, CAN_TDT0R_TGT); + } + + /* Set up the data field */ + WRITE_REG(hcan->Instance->sTxMailBox[transmitmailbox].TDHR, + ((uint32_t)aData[7] << CAN_TDH0R_DATA7_Pos) | + ((uint32_t)aData[6] << CAN_TDH0R_DATA6_Pos) | + ((uint32_t)aData[5] << CAN_TDH0R_DATA5_Pos) | + ((uint32_t)aData[4] << CAN_TDH0R_DATA4_Pos)); + WRITE_REG(hcan->Instance->sTxMailBox[transmitmailbox].TDLR, + ((uint32_t)aData[3] << CAN_TDL0R_DATA3_Pos) | + ((uint32_t)aData[2] << CAN_TDL0R_DATA2_Pos) | + ((uint32_t)aData[1] << CAN_TDL0R_DATA1_Pos) | + ((uint32_t)aData[0] << CAN_TDL0R_DATA0_Pos)); + + /* Request transmission */ + SET_BIT(hcan->Instance->sTxMailBox[transmitmailbox].TIR, CAN_TI0R_TXRQ); + + /* Return function status */ + return HAL_OK; + } + else + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_PARAM; + + return HAL_ERROR; + } + } + else + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_NOT_INITIALIZED; + + return HAL_ERROR; + } +} + +/** + * @brief Abort transmission requests + * @param hcan pointer to an CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @param TxMailboxes List of the Tx Mailboxes to abort. + * This parameter can be any combination of @arg CAN_Tx_Mailboxes. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CAN_AbortTxRequest(CAN_HandleTypeDef* hcan, uint32_t TxMailboxes) +{ + HAL_CAN_StateTypeDef state = hcan->State; + + /* Check function parameters */ + assert_param(IS_CAN_TX_MAILBOX_LIST(TxMailboxes)); + + if ((state == HAL_CAN_STATE_READY) || + (state == HAL_CAN_STATE_LISTENING)) + { + /* Check Tx Mailbox 0 */ + if ((TxMailboxes & CAN_TX_MAILBOX0) != 0U) + { + /* Add cancellation request for Tx Mailbox 0 */ + SET_BIT(hcan->Instance->TSR, CAN_TSR_ABRQ0); + } + + /* Check Tx Mailbox 1 */ + if ((TxMailboxes & CAN_TX_MAILBOX1) != 0U) + { + /* Add cancellation request for Tx Mailbox 1 */ + SET_BIT(hcan->Instance->TSR, CAN_TSR_ABRQ1); + } + + /* Check Tx Mailbox 2 */ + if ((TxMailboxes & CAN_TX_MAILBOX2) != 0U) + { + /* Add cancellation request for Tx Mailbox 2 */ + SET_BIT(hcan->Instance->TSR, CAN_TSR_ABRQ2); + } + + /* Return function status */ + return HAL_OK; + } + else + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_NOT_INITIALIZED; + + return HAL_ERROR; + } +} + +/** + * @brief Return Tx Mailboxes free level: number of free Tx Mailboxes. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval Number of free Tx Mailboxes. + */ +uint32_t HAL_CAN_GetTxMailboxesFreeLevel(CAN_HandleTypeDef* hcan) +{ + uint32_t freelevel = 0U; + HAL_CAN_StateTypeDef state = hcan->State; + + if ((state == HAL_CAN_STATE_READY) || + (state == HAL_CAN_STATE_LISTENING)) + { + /* Check Tx Mailbox 0 status */ + if ((hcan->Instance->TSR & CAN_TSR_TME0) != 0U) + { + freelevel++; + } + + /* Check Tx Mailbox 1 status */ + if ((hcan->Instance->TSR & CAN_TSR_TME1) != 0U) + { + freelevel++; + } + + /* Check Tx Mailbox 2 status */ + if ((hcan->Instance->TSR & CAN_TSR_TME2) != 0U) + { + freelevel++; + } + } + + /* Return Tx Mailboxes free level */ + return freelevel; +} + +/** + * @brief Check if a transmission request is pending on the selected Tx + * Mailboxes. + * @param hcan pointer to an CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @param TxMailboxes List of Tx Mailboxes to check. + * This parameter can be any combination of @arg CAN_Tx_Mailboxes. + * @retval Status + * - 0 : No pending transmission request on any selected Tx Mailboxes. + * - 1 : Pending transmission request on at least one of the selected + * Tx Mailbox. + */ +uint32_t HAL_CAN_IsTxMessagePending(CAN_HandleTypeDef* hcan, uint32_t TxMailboxes) +{ + uint32_t status = 0U; + HAL_CAN_StateTypeDef state = hcan->State; + + /* Check function parameters */ + assert_param(IS_CAN_TX_MAILBOX_LIST(TxMailboxes)); + + if ((state == HAL_CAN_STATE_READY) || + (state == HAL_CAN_STATE_LISTENING)) + { + /* Check pending transmission request on the selected Tx Mailboxes */ + if ((hcan->Instance->TSR & (TxMailboxes << CAN_TSR_TME0_Pos)) != (TxMailboxes << CAN_TSR_TME0_Pos)) + { + status = 1U; + } + } + + /* Return status */ + return status; +} + +/** + * @brief Return timestamp of Tx message sent, if time triggered communication + mode is enabled. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @param TxMailbox Tx Mailbox where the timestamp of message sent will be + * read. + * This parameter can be one value of @arg CAN_Tx_Mailboxes. + * @retval Timestamp of message sent from Tx Mailbox. + */ +uint32_t HAL_CAN_GetTxTimestamp(CAN_HandleTypeDef* hcan, uint32_t TxMailbox) +{ + uint32_t timestamp = 0U; + uint32_t transmitmailbox; + HAL_CAN_StateTypeDef state = hcan->State; + + /* Check function parameters */ + assert_param(IS_CAN_TX_MAILBOX(TxMailbox)); + + if ((state == HAL_CAN_STATE_READY) || + (state == HAL_CAN_STATE_LISTENING)) + { + /* Select the Tx mailbox */ + transmitmailbox = POSITION_VAL(TxMailbox); + + /* Get timestamp */ + timestamp = (hcan->Instance->sTxMailBox[transmitmailbox].TDTR & CAN_TDT0R_TIME) >> CAN_TDT0R_TIME_Pos; + } + + /* Return the timestamp */ + return timestamp; +} + +/** + * @brief Get an CAN frame from the Rx FIFO zone into the message RAM. + * @param hcan pointer to an CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @param RxFifo Fifo number of the received message to be read. + * This parameter can be a value of @arg CAN_receive_FIFO_number. + * @param pHeader pointer to a CAN_RxHeaderTypeDef structure where the header + * of the Rx frame will be stored. + * @param aData array where the payload of the Rx frame will be stored. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CAN_GetRxMessage(CAN_HandleTypeDef* hcan, uint32_t RxFifo, CAN_RxHeaderTypeDef* pHeader, uint8_t aData[]) +{ + HAL_CAN_StateTypeDef state = hcan->State; + + assert_param(IS_CAN_RX_FIFO(RxFifo)); + + if ((state == HAL_CAN_STATE_READY) || + (state == HAL_CAN_STATE_LISTENING)) + { + /* Check the Rx FIFO */ + if (RxFifo == CAN_RX_FIFO0) /* Rx element is assigned to Rx FIFO 0 */ + { + /* Check that the Rx FIFO 0 is not empty */ + if ((hcan->Instance->RF0R & CAN_RF0R_FMP0) == 0U) + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_PARAM; + + return HAL_ERROR; + } + } + else /* Rx element is assigned to Rx FIFO 1 */ + { + /* Check that the Rx FIFO 1 is not empty */ + if ((hcan->Instance->RF1R & CAN_RF1R_FMP1) == 0U) + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_PARAM; + + return HAL_ERROR; + } + } + + /* Get the header */ + pHeader->IDE = CAN_RI0R_IDE & hcan->Instance->sFIFOMailBox[RxFifo].RIR; + + if (pHeader->IDE == CAN_ID_STD) + { + pHeader->StdId = (CAN_RI0R_STID & hcan->Instance->sFIFOMailBox[RxFifo].RIR) >> CAN_TI0R_STID_Pos; + } + else + { + pHeader->ExtId = ((CAN_RI0R_EXID | CAN_RI0R_STID) & hcan->Instance->sFIFOMailBox[RxFifo].RIR) >> CAN_RI0R_EXID_Pos; + } + + pHeader->RTR = (CAN_RI0R_RTR & hcan->Instance->sFIFOMailBox[RxFifo].RIR); + pHeader->DLC = (CAN_RDT0R_DLC & hcan->Instance->sFIFOMailBox[RxFifo].RDTR) >> CAN_RDT0R_DLC_Pos; + pHeader->FilterMatchIndex = (CAN_RDT0R_FMI & hcan->Instance->sFIFOMailBox[RxFifo].RDTR) >> CAN_RDT0R_FMI_Pos; + pHeader->Timestamp = (CAN_RDT0R_TIME & hcan->Instance->sFIFOMailBox[RxFifo].RDTR) >> CAN_RDT0R_TIME_Pos; + + /* Get the data */ + aData[0] = (uint8_t)((CAN_RDL0R_DATA0 & hcan->Instance->sFIFOMailBox[RxFifo].RDLR) >> CAN_RDL0R_DATA0_Pos); + aData[1] = (uint8_t)((CAN_RDL0R_DATA1 & hcan->Instance->sFIFOMailBox[RxFifo].RDLR) >> CAN_RDL0R_DATA1_Pos); + aData[2] = (uint8_t)((CAN_RDL0R_DATA2 & hcan->Instance->sFIFOMailBox[RxFifo].RDLR) >> CAN_RDL0R_DATA2_Pos); + aData[3] = (uint8_t)((CAN_RDL0R_DATA3 & hcan->Instance->sFIFOMailBox[RxFifo].RDLR) >> CAN_RDL0R_DATA3_Pos); + aData[4] = (uint8_t)((CAN_RDH0R_DATA4 & hcan->Instance->sFIFOMailBox[RxFifo].RDHR) >> CAN_RDH0R_DATA4_Pos); + aData[5] = (uint8_t)((CAN_RDH0R_DATA5 & hcan->Instance->sFIFOMailBox[RxFifo].RDHR) >> CAN_RDH0R_DATA5_Pos); + aData[6] = (uint8_t)((CAN_RDH0R_DATA6 & hcan->Instance->sFIFOMailBox[RxFifo].RDHR) >> CAN_RDH0R_DATA6_Pos); + aData[7] = (uint8_t)((CAN_RDH0R_DATA7 & hcan->Instance->sFIFOMailBox[RxFifo].RDHR) >> CAN_RDH0R_DATA7_Pos); + + /* Release the FIFO */ + if (RxFifo == CAN_RX_FIFO0) /* Rx element is assigned to Rx FIFO 0 */ + { + /* Release RX FIFO 0 */ + SET_BIT(hcan->Instance->RF0R, CAN_RF0R_RFOM0); + } + else /* Rx element is assigned to Rx FIFO 1 */ + { + /* Release RX FIFO 1 */ + SET_BIT(hcan->Instance->RF1R, CAN_RF1R_RFOM1); + } + + /* Return function status */ + return HAL_OK; + } + else + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_NOT_INITIALIZED; + + return HAL_ERROR; + } +} + +/** + * @brief Return Rx FIFO fill level. + * @param hcan pointer to an CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @param RxFifo Rx FIFO. + * This parameter can be a value of @arg CAN_receive_FIFO_number. + * @retval Number of messages available in Rx FIFO. + */ +uint32_t HAL_CAN_GetRxFifoFillLevel(CAN_HandleTypeDef* hcan, uint32_t RxFifo) +{ + uint32_t filllevel = 0U; + HAL_CAN_StateTypeDef state = hcan->State; + + /* Check function parameters */ + assert_param(IS_CAN_RX_FIFO(RxFifo)); + + if ((state == HAL_CAN_STATE_READY) || + (state == HAL_CAN_STATE_LISTENING)) + { + if (RxFifo == CAN_RX_FIFO0) + { + filllevel = hcan->Instance->RF0R & CAN_RF0R_FMP0; + } + else /* RxFifo == CAN_RX_FIFO1 */ + { + filllevel = hcan->Instance->RF1R & CAN_RF1R_FMP1; + } + } + + /* Return Rx FIFO fill level */ + return filllevel; +} + +/** + * @} + */ + +/** @defgroup CAN_Exported_Functions_Group4 Interrupts management + * @brief Interrupts management + * +@verbatim + ============================================================================== + ##### Interrupts management ##### + ============================================================================== + [..] This section provides functions allowing to: + (+) HAL_CAN_ActivateNotification : Enable interrupts + (+) HAL_CAN_DeactivateNotification : Disable interrupts + (+) HAL_CAN_IRQHandler : Handles CAN interrupt request + +@endverbatim + * @{ + */ + +/** + * @brief Enable interrupts. + * @param hcan pointer to an CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @param ActiveITs indicates which interrupts will be enabled. + * This parameter can be any combination of @arg CAN_Interrupts. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CAN_ActivateNotification(CAN_HandleTypeDef* hcan, uint32_t ActiveITs) +{ + HAL_CAN_StateTypeDef state = hcan->State; + + /* Check function parameters */ + assert_param(IS_CAN_IT(ActiveITs)); + + if ((state == HAL_CAN_STATE_READY) || + (state == HAL_CAN_STATE_LISTENING)) + { + /* Enable the selected interrupts */ + __HAL_CAN_ENABLE_IT(hcan, ActiveITs); + + /* Return function status */ + return HAL_OK; + } + else + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_NOT_INITIALIZED; + + return HAL_ERROR; + } +} + +/** + * @brief Disable interrupts. + * @param hcan pointer to an CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @param InactiveITs indicates which interrupts will be disabled. + * This parameter can be any combination of @arg CAN_Interrupts. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CAN_DeactivateNotification(CAN_HandleTypeDef* hcan, uint32_t InactiveITs) +{ + HAL_CAN_StateTypeDef state = hcan->State; + + /* Check function parameters */ + assert_param(IS_CAN_IT(InactiveITs)); + + if ((state == HAL_CAN_STATE_READY) || + (state == HAL_CAN_STATE_LISTENING)) + { + /* Disable the selected interrupts */ + __HAL_CAN_DISABLE_IT(hcan, InactiveITs); + + /* Return function status */ + return HAL_OK; + } + else + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_NOT_INITIALIZED; + + return HAL_ERROR; + } +} + +/** + * @brief Handles CAN interrupt request + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +void HAL_CAN_IRQHandler(CAN_HandleTypeDef* hcan) +{ + uint32_t errorcode = HAL_CAN_ERROR_NONE; + uint32_t interrupts = READ_REG(hcan->Instance->IER); + uint32_t msrflags = READ_REG(hcan->Instance->MSR); + uint32_t tsrflags = READ_REG(hcan->Instance->TSR); + uint32_t rf0rflags = READ_REG(hcan->Instance->RF0R); + uint32_t rf1rflags = READ_REG(hcan->Instance->RF1R); + uint32_t esrflags = READ_REG(hcan->Instance->ESR); + + /* Transmit Mailbox empty interrupt management *****************************/ + if ((interrupts & CAN_IT_TX_MAILBOX_EMPTY) != 0U) + { + /* Transmit Mailbox 0 management *****************************************/ + if ((tsrflags & CAN_TSR_RQCP0) != 0U) + { + /* Clear the Transmission Complete flag (and TXOK0,ALST0,TERR0 bits) */ + __HAL_CAN_CLEAR_FLAG(hcan, CAN_FLAG_RQCP0); + + if ((tsrflags & CAN_TSR_TXOK0) != 0U) + { + /* Transmission Mailbox 0 complete callback */ +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + /* Call registered callback*/ + hcan->TxMailbox0CompleteCallback(hcan); +#else + /* Call weak (surcharged) callback */ + HAL_CAN_TxMailbox0CompleteCallback(hcan); +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ + } + else + { + if ((tsrflags & CAN_TSR_ALST0) != 0U) + { + /* Update error code */ + errorcode |= HAL_CAN_ERROR_TX_ALST0; + } + else if ((tsrflags & CAN_TSR_TERR0) != 0U) + { + /* Update error code */ + errorcode |= HAL_CAN_ERROR_TX_TERR0; + } + else + { + /* Transmission Mailbox 0 abort callback */ +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + /* Call registered callback*/ + hcan->TxMailbox0AbortCallback(hcan); +#else + /* Call weak (surcharged) callback */ + HAL_CAN_TxMailbox0AbortCallback(hcan); +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ + } + } + } + + /* Transmit Mailbox 1 management *****************************************/ + if ((tsrflags & CAN_TSR_RQCP1) != 0U) + { + /* Clear the Transmission Complete flag (and TXOK1,ALST1,TERR1 bits) */ + __HAL_CAN_CLEAR_FLAG(hcan, CAN_FLAG_RQCP1); + + if ((tsrflags & CAN_TSR_TXOK1) != 0U) + { + /* Transmission Mailbox 1 complete callback */ +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + /* Call registered callback*/ + hcan->TxMailbox1CompleteCallback(hcan); +#else + /* Call weak (surcharged) callback */ + HAL_CAN_TxMailbox1CompleteCallback(hcan); +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ + } + else + { + if ((tsrflags & CAN_TSR_ALST1) != 0U) + { + /* Update error code */ + errorcode |= HAL_CAN_ERROR_TX_ALST1; + } + else if ((tsrflags & CAN_TSR_TERR1) != 0U) + { + /* Update error code */ + errorcode |= HAL_CAN_ERROR_TX_TERR1; + } + else + { + /* Transmission Mailbox 1 abort callback */ +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + /* Call registered callback*/ + hcan->TxMailbox1AbortCallback(hcan); +#else + /* Call weak (surcharged) callback */ + HAL_CAN_TxMailbox1AbortCallback(hcan); +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ + } + } + } + + /* Transmit Mailbox 2 management *****************************************/ + if ((tsrflags & CAN_TSR_RQCP2) != 0U) + { + /* Clear the Transmission Complete flag (and TXOK2,ALST2,TERR2 bits) */ + __HAL_CAN_CLEAR_FLAG(hcan, CAN_FLAG_RQCP2); + + if ((tsrflags & CAN_TSR_TXOK2) != 0U) + { + /* Transmission Mailbox 2 complete callback */ +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + /* Call registered callback*/ + hcan->TxMailbox2CompleteCallback(hcan); +#else + /* Call weak (surcharged) callback */ + HAL_CAN_TxMailbox2CompleteCallback(hcan); +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ + } + else + { + if ((tsrflags & CAN_TSR_ALST2) != 0U) + { + /* Update error code */ + errorcode |= HAL_CAN_ERROR_TX_ALST2; + } + else if ((tsrflags & CAN_TSR_TERR2) != 0U) + { + /* Update error code */ + errorcode |= HAL_CAN_ERROR_TX_TERR2; + } + else + { + /* Transmission Mailbox 2 abort callback */ +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + /* Call registered callback*/ + hcan->TxMailbox2AbortCallback(hcan); +#else + /* Call weak (surcharged) callback */ + HAL_CAN_TxMailbox2AbortCallback(hcan); +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ + } + } + } + } + + /* Receive FIFO 0 overrun interrupt management *****************************/ + if ((interrupts & CAN_IT_RX_FIFO0_OVERRUN) != 0U) + { + if ((rf0rflags & CAN_RF0R_FOVR0) != 0U) + { + /* Set CAN error code to Rx Fifo 0 overrun error */ + errorcode |= HAL_CAN_ERROR_RX_FOV0; + + /* Clear FIFO0 Overrun Flag */ + __HAL_CAN_CLEAR_FLAG(hcan, CAN_FLAG_FOV0); + } + } + + /* Receive FIFO 0 full interrupt management ********************************/ + if ((interrupts & CAN_IT_RX_FIFO0_FULL) != 0U) + { + if ((rf0rflags & CAN_RF0R_FULL0) != 0U) + { + /* Clear FIFO 0 full Flag */ + __HAL_CAN_CLEAR_FLAG(hcan, CAN_FLAG_FF0); + + /* Receive FIFO 0 full Callback */ +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + /* Call registered callback*/ + hcan->RxFifo0FullCallback(hcan); +#else + /* Call weak (surcharged) callback */ + HAL_CAN_RxFifo0FullCallback(hcan); +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ + } + } + + /* Receive FIFO 0 message pending interrupt management *********************/ + if ((interrupts & CAN_IT_RX_FIFO0_MSG_PENDING) != 0U) + { + /* Check if message is still pending */ + if ((hcan->Instance->RF0R & CAN_RF0R_FMP0) != 0U) + { + /* Receive FIFO 0 mesage pending Callback */ +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + /* Call registered callback*/ + hcan->RxFifo0MsgPendingCallback(hcan); +#else + /* Call weak (surcharged) callback */ + HAL_CAN_RxFifo0MsgPendingCallback(hcan); +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ + } + } + + /* Receive FIFO 1 overrun interrupt management *****************************/ + if ((interrupts & CAN_IT_RX_FIFO1_OVERRUN) != 0U) + { + if ((rf1rflags & CAN_RF1R_FOVR1) != 0U) + { + /* Set CAN error code to Rx Fifo 1 overrun error */ + errorcode |= HAL_CAN_ERROR_RX_FOV1; + + /* Clear FIFO1 Overrun Flag */ + __HAL_CAN_CLEAR_FLAG(hcan, CAN_FLAG_FOV1); + } + } + + /* Receive FIFO 1 full interrupt management ********************************/ + if ((interrupts & CAN_IT_RX_FIFO1_FULL) != 0U) + { + if ((rf1rflags & CAN_RF1R_FULL1) != 0U) + { + /* Clear FIFO 1 full Flag */ + __HAL_CAN_CLEAR_FLAG(hcan, CAN_FLAG_FF1); + + /* Receive FIFO 1 full Callback */ +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + /* Call registered callback*/ + hcan->RxFifo1FullCallback(hcan); +#else + /* Call weak (surcharged) callback */ + HAL_CAN_RxFifo1FullCallback(hcan); +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ + } + } + + /* Receive FIFO 1 message pending interrupt management *********************/ + if ((interrupts & CAN_IT_RX_FIFO1_MSG_PENDING) != 0U) + { + /* Check if message is still pending */ + if ((hcan->Instance->RF1R & CAN_RF1R_FMP1) != 0U) + { + /* Receive FIFO 1 mesage pending Callback */ +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + /* Call registered callback*/ + hcan->RxFifo1MsgPendingCallback(hcan); +#else + /* Call weak (surcharged) callback */ + HAL_CAN_RxFifo1MsgPendingCallback(hcan); +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ + } + } + + /* Sleep interrupt management *********************************************/ + if ((interrupts & CAN_IT_SLEEP_ACK) != 0U) + { + if ((msrflags & CAN_MSR_SLAKI) != 0U) + { + /* Clear Sleep interrupt Flag */ + __HAL_CAN_CLEAR_FLAG(hcan, CAN_FLAG_SLAKI); + + /* Sleep Callback */ +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + /* Call registered callback*/ + hcan->SleepCallback(hcan); +#else + /* Call weak (surcharged) callback */ + HAL_CAN_SleepCallback(hcan); +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ + } + } + + /* WakeUp interrupt management *********************************************/ + if ((interrupts & CAN_IT_WAKEUP) != 0U) + { + if ((msrflags & CAN_MSR_WKUI) != 0U) + { + /* Clear WakeUp Flag */ + __HAL_CAN_CLEAR_FLAG(hcan, CAN_FLAG_WKU); + + /* WakeUp Callback */ +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + /* Call registered callback*/ + hcan->WakeUpFromRxMsgCallback(hcan); +#else + /* Call weak (surcharged) callback */ + HAL_CAN_WakeUpFromRxMsgCallback(hcan); +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ + } + } + + /* Error interrupts management *********************************************/ + if ((interrupts & CAN_IT_ERROR) != 0U) + { + if ((msrflags & CAN_MSR_ERRI) != 0U) + { + /* Check Error Warning Flag */ + if (((interrupts & CAN_IT_ERROR_WARNING) != 0U) && + ((esrflags & CAN_ESR_EWGF) != 0U)) + { + /* Set CAN error code to Error Warning */ + errorcode |= HAL_CAN_ERROR_EWG; + + /* No need for clear of Error Warning Flag as read-only */ + } + + /* Check Error Passive Flag */ + if (((interrupts & CAN_IT_ERROR_PASSIVE) != 0U) && + ((esrflags & CAN_ESR_EPVF) != 0U)) + { + /* Set CAN error code to Error Passive */ + errorcode |= HAL_CAN_ERROR_EPV; + + /* No need for clear of Error Passive Flag as read-only */ + } + + /* Check Bus-off Flag */ + if (((interrupts & CAN_IT_BUSOFF) != 0U) && + ((esrflags & CAN_ESR_BOFF) != 0U)) + { + /* Set CAN error code to Bus-Off */ + errorcode |= HAL_CAN_ERROR_BOF; + + /* No need for clear of Error Bus-Off as read-only */ + } + + /* Check Last Error Code Flag */ + if (((interrupts & CAN_IT_LAST_ERROR_CODE) != 0U) && + ((esrflags & CAN_ESR_LEC) != 0U)) + { + switch (esrflags & CAN_ESR_LEC) + { + case (CAN_ESR_LEC_0): + /* Set CAN error code to Stuff error */ + errorcode |= HAL_CAN_ERROR_STF; + break; + + case (CAN_ESR_LEC_1): + /* Set CAN error code to Form error */ + errorcode |= HAL_CAN_ERROR_FOR; + break; + + case (CAN_ESR_LEC_1 | CAN_ESR_LEC_0): + /* Set CAN error code to Acknowledgement error */ + errorcode |= HAL_CAN_ERROR_ACK; + break; + + case (CAN_ESR_LEC_2): + /* Set CAN error code to Bit recessive error */ + errorcode |= HAL_CAN_ERROR_BR; + break; + + case (CAN_ESR_LEC_2 | CAN_ESR_LEC_0): + /* Set CAN error code to Bit Dominant error */ + errorcode |= HAL_CAN_ERROR_BD; + break; + + case (CAN_ESR_LEC_2 | CAN_ESR_LEC_1): + /* Set CAN error code to CRC error */ + errorcode |= HAL_CAN_ERROR_CRC; + break; + + default: + break; + } + + /* Clear Last error code Flag */ + CLEAR_BIT(hcan->Instance->ESR, CAN_ESR_LEC); + } + } + + /* Clear ERRI Flag */ + __HAL_CAN_CLEAR_FLAG(hcan, CAN_FLAG_ERRI); + } + + /* Call the Error call Back in case of Errors */ + if (errorcode != HAL_CAN_ERROR_NONE) + { + /* Update error code in handle */ + hcan->ErrorCode |= errorcode; + + /* Call Error callback function */ +#if USE_HAL_CAN_REGISTER_CALLBACKS == 1 + /* Call registered callback*/ + hcan->ErrorCallback(hcan); +#else + /* Call weak (surcharged) callback */ + HAL_CAN_ErrorCallback(hcan); +#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */ + } +} + +/** + * @} + */ + +/** @defgroup CAN_Exported_Functions_Group5 Callback functions + * @brief CAN Callback functions + * +@verbatim + ============================================================================== + ##### Callback functions ##### + ============================================================================== + [..] + This subsection provides the following callback functions: + (+) HAL_CAN_TxMailbox0CompleteCallback + (+) HAL_CAN_TxMailbox1CompleteCallback + (+) HAL_CAN_TxMailbox2CompleteCallback + (+) HAL_CAN_TxMailbox0AbortCallback + (+) HAL_CAN_TxMailbox1AbortCallback + (+) HAL_CAN_TxMailbox2AbortCallback + (+) HAL_CAN_RxFifo0MsgPendingCallback + (+) HAL_CAN_RxFifo0FullCallback + (+) HAL_CAN_RxFifo1MsgPendingCallback + (+) HAL_CAN_RxFifo1FullCallback + (+) HAL_CAN_SleepCallback + (+) HAL_CAN_WakeUpFromRxMsgCallback + (+) HAL_CAN_ErrorCallback + +@endverbatim + * @{ + */ + +/** + * @brief Transmission Mailbox 0 complete callback. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +__weak void HAL_CAN_TxMailbox0CompleteCallback(CAN_HandleTypeDef* hcan) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hcan); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CAN_TxMailbox0CompleteCallback could be implemented in the + user file + */ +} + +/** + * @brief Transmission Mailbox 1 complete callback. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +__weak void HAL_CAN_TxMailbox1CompleteCallback(CAN_HandleTypeDef* hcan) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hcan); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CAN_TxMailbox1CompleteCallback could be implemented in the + user file + */ +} + +/** + * @brief Transmission Mailbox 2 complete callback. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +__weak void HAL_CAN_TxMailbox2CompleteCallback(CAN_HandleTypeDef* hcan) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hcan); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CAN_TxMailbox2CompleteCallback could be implemented in the + user file + */ +} + +/** + * @brief Transmission Mailbox 0 Cancellation callback. + * @param hcan pointer to an CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +__weak void HAL_CAN_TxMailbox0AbortCallback(CAN_HandleTypeDef* hcan) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hcan); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CAN_TxMailbox0AbortCallback could be implemented in the + user file + */ +} + +/** + * @brief Transmission Mailbox 1 Cancellation callback. + * @param hcan pointer to an CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +__weak void HAL_CAN_TxMailbox1AbortCallback(CAN_HandleTypeDef* hcan) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hcan); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CAN_TxMailbox1AbortCallback could be implemented in the + user file + */ +} + +/** + * @brief Transmission Mailbox 2 Cancellation callback. + * @param hcan pointer to an CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +__weak void HAL_CAN_TxMailbox2AbortCallback(CAN_HandleTypeDef* hcan) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hcan); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CAN_TxMailbox2AbortCallback could be implemented in the + user file + */ +} + +/** + * @brief Rx FIFO 0 message pending callback. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +__weak void HAL_CAN_RxFifo0MsgPendingCallback(CAN_HandleTypeDef* hcan) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hcan); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CAN_RxFifo0MsgPendingCallback could be implemented in the + user file + */ +} + +/** + * @brief Rx FIFO 0 full callback. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +__weak void HAL_CAN_RxFifo0FullCallback(CAN_HandleTypeDef* hcan) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hcan); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CAN_RxFifo0FullCallback could be implemented in the user + file + */ +} + +/** + * @brief Rx FIFO 1 message pending callback. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +__weak void HAL_CAN_RxFifo1MsgPendingCallback(CAN_HandleTypeDef* hcan) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hcan); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CAN_RxFifo1MsgPendingCallback could be implemented in the + user file + */ +} + +/** + * @brief Rx FIFO 1 full callback. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +__weak void HAL_CAN_RxFifo1FullCallback(CAN_HandleTypeDef* hcan) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hcan); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CAN_RxFifo1FullCallback could be implemented in the user + file + */ +} + +/** + * @brief Sleep callback. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +__weak void HAL_CAN_SleepCallback(CAN_HandleTypeDef* hcan) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hcan); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CAN_SleepCallback could be implemented in the user file + */ +} + +/** + * @brief WakeUp from Rx message callback. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +__weak void HAL_CAN_WakeUpFromRxMsgCallback(CAN_HandleTypeDef* hcan) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hcan); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CAN_WakeUpFromRxMsgCallback could be implemented in the + user file + */ +} + +/** + * @brief Error CAN callback. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval None + */ +__weak void HAL_CAN_ErrorCallback(CAN_HandleTypeDef* hcan) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hcan); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_CAN_ErrorCallback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup CAN_Exported_Functions_Group6 Peripheral State and Error functions + * @brief CAN Peripheral State functions + * +@verbatim + ============================================================================== + ##### Peripheral State and Error functions ##### + ============================================================================== + [..] + This subsection provides functions allowing to : + (+) HAL_CAN_GetState() : Return the CAN state. + (+) HAL_CAN_GetError() : Return the CAN error codes if any. + (+) HAL_CAN_ResetError(): Reset the CAN error codes if any. + +@endverbatim + * @{ + */ + +/** + * @brief Return the CAN state. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval HAL state + */ +HAL_CAN_StateTypeDef HAL_CAN_GetState(CAN_HandleTypeDef* hcan) +{ + HAL_CAN_StateTypeDef state = hcan->State; + + if ((state == HAL_CAN_STATE_READY) || + (state == HAL_CAN_STATE_LISTENING)) + { + /* Check sleep mode acknowledge flag */ + if ((hcan->Instance->MSR & CAN_MSR_SLAK) != 0U) + { + /* Sleep mode is active */ + state = HAL_CAN_STATE_SLEEP_ACTIVE; + } + /* Check sleep mode request flag */ + else if ((hcan->Instance->MCR & CAN_MCR_SLEEP) != 0U) + { + /* Sleep mode request is pending */ + state = HAL_CAN_STATE_SLEEP_PENDING; + } + else + { + /* Neither sleep mode request nor sleep mode acknowledge */ + } + } + + /* Return CAN state */ + return state; +} + +/** + * @brief Return the CAN error code. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval CAN Error Code + */ +uint32_t HAL_CAN_GetError(CAN_HandleTypeDef* hcan) +{ + /* Return CAN error code */ + return hcan->ErrorCode; +} + +/** + * @brief Reset the CAN error code. + * @param hcan pointer to a CAN_HandleTypeDef structure that contains + * the configuration information for the specified CAN. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_CAN_ResetError(CAN_HandleTypeDef* hcan) +{ + HAL_StatusTypeDef status = HAL_OK; + HAL_CAN_StateTypeDef state = hcan->State; + + if ((state == HAL_CAN_STATE_READY) || + (state == HAL_CAN_STATE_LISTENING)) + { + /* Reset CAN error code */ + hcan->ErrorCode = 0U; + } + else + { + /* Update error code */ + hcan->ErrorCode |= HAL_CAN_ERROR_NOT_INITIALIZED; + + status = HAL_ERROR; + } + + /* Return the status */ + return status; +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_CAN_MODULE_ENABLED */ + +/** + * @} + */ + +#endif /* CAN1 */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_cortex.c b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_cortex.c similarity index 85% rename from EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_cortex.c rename to EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_cortex.c index 37bbca8d..dbf3f2c4 100644 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_cortex.c +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_cortex.c @@ -1,9 +1,7 @@ /** ****************************************************************************** - * @file stm32f4xx_hal_cortex.c + * @file stm32f1xx_hal_cortex.c * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 * @brief CORTEX HAL module driver. * This file provides firmware functions to manage the following * functionalities of the CORTEX: @@ -20,13 +18,13 @@ =========================================================== [..] This section provides functions allowing to configure the NVIC interrupts (IRQ). - The Cortex-M4 exceptions are managed by CMSIS functions. + The Cortex-M3 exceptions are managed by CMSIS functions. (#) Configure the NVIC Priority Grouping using HAL_NVIC_SetPriorityGrouping() function according to the following table. (#) Configure the priority of the selected IRQ Channels using HAL_NVIC_SetPriority(). (#) Enable the selected IRQ Channels using HAL_NVIC_EnableIRQ(). - (#) please refer to programing manual for details in how to configure priority. + (#) please refer to programming manual for details in how to configure priority. -@- When the NVIC_PRIORITYGROUP_0 is selected, IRQ preemption is no more possible. The pending IRQ priority will be managed only by the sub priority. @@ -42,10 +40,10 @@ [..] Setup SysTick Timer for time base. - (+) The HAL_SYSTICK_Config() function calls the SysTick_Config() function which + (+) The HAL_SYSTICK_Config()function calls the SysTick_Config() function which is a CMSIS function that: (++) Configures the SysTick Reload register with value passed as function parameter. - (++) Configures the SysTick IRQ priority to the lowest value (0x0FU). + (++) Configures the SysTick IRQ priority to the lowest value 0x0F. (++) Resets the SysTick Counter register. (++) Configures the SysTick Counter clock source to be Core Clock Source (HCLK). (++) Enables the SysTick Interrupt. @@ -54,7 +52,7 @@ (+) You can change the SysTick Clock source to be HCLK_Div8 by calling the macro __HAL_CORTEX_SYSTICKCLK_CONFIG(SYSTICK_CLKSOURCE_HCLK_DIV8) just after the HAL_SYSTICK_Config() function call. The __HAL_CORTEX_SYSTICKCLK_CONFIG() macro is defined - inside the stm32f4xx_hal_cortex.h file. + inside the stm32f1xx_hal_cortex.h file. (+) You can change the SysTick IRQ priority by calling the HAL_NVIC_SetPriority(SysTick_IRQn,...) function just after the HAL_SYSTICK_Config() function @@ -70,37 +68,21 @@ ****************************************************************************** * @attention * - *

© COPYRIGHT(c) 2016 STMicroelectronics

+ *

© Copyright (c) 2017 STMicroelectronics. + * All rights reserved.

* - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause * ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" +#include "stm32f1xx_hal.h" -/** @addtogroup STM32F4xx_HAL_Driver +/** @addtogroup STM32F1xx_HAL_Driver * @{ */ @@ -124,8 +106,8 @@ /** @defgroup CORTEX_Exported_Functions_Group1 Initialization and de-initialization functions - * @brief Initialization and Configuration functions - * + * @brief Initialization and Configuration functions + * @verbatim ============================================================================== ##### Initialization and de-initialization functions ##### @@ -162,6 +144,7 @@ void HAL_NVIC_SetPriorityGrouping(uint32_t PriorityGroup) { /* Check the parameters */ assert_param(IS_NVIC_PRIORITY_GROUP(PriorityGroup)); + /* Set the PRIGROUP[10:8] bits according to the PriorityGroup parameter value */ NVIC_SetPriorityGrouping(PriorityGroup); } @@ -170,7 +153,7 @@ void HAL_NVIC_SetPriorityGrouping(uint32_t PriorityGroup) * @brief Sets the priority of an interrupt. * @param IRQn: External interrupt number. * This parameter can be an enumerator of IRQn_Type enumeration - * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xx.h)) * @param PreemptPriority: The preemption priority for the IRQn channel. * This parameter can be a value between 0 and 15 * A lower priority value indicates a higher priority @@ -182,10 +165,13 @@ void HAL_NVIC_SetPriorityGrouping(uint32_t PriorityGroup) void HAL_NVIC_SetPriority(IRQn_Type IRQn, uint32_t PreemptPriority, uint32_t SubPriority) { uint32_t prioritygroup = 0x00U; + /* Check the parameters */ assert_param(IS_NVIC_SUB_PRIORITY(SubPriority)); assert_param(IS_NVIC_PREEMPTION_PRIORITY(PreemptPriority)); + prioritygroup = NVIC_GetPriorityGrouping(); + NVIC_SetPriority(IRQn, NVIC_EncodePriority(prioritygroup, PreemptPriority, SubPriority)); } @@ -195,13 +181,14 @@ void HAL_NVIC_SetPriority(IRQn_Type IRQn, uint32_t PreemptPriority, uint32_t Sub * function should be called before. * @param IRQn External interrupt number. * This parameter can be an enumerator of IRQn_Type enumeration - * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xxx.h)) * @retval None */ void HAL_NVIC_EnableIRQ(IRQn_Type IRQn) { /* Check the parameters */ assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); + /* Enable interrupt */ NVIC_EnableIRQ(IRQn); } @@ -210,13 +197,14 @@ void HAL_NVIC_EnableIRQ(IRQn_Type IRQn) * @brief Disables a device specific interrupt in the NVIC interrupt controller. * @param IRQn External interrupt number. * This parameter can be an enumerator of IRQn_Type enumeration - * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xxx.h)) * @retval None */ void HAL_NVIC_DisableIRQ(IRQn_Type IRQn) { /* Check the parameters */ assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); + /* Disable interrupt */ NVIC_DisableIRQ(IRQn); } @@ -247,8 +235,8 @@ uint32_t HAL_SYSTICK_Config(uint32_t TicksNumb) */ /** @defgroup CORTEX_Exported_Functions_Group2 Peripheral Control functions - * @brief Cortex control functions - * + * @brief Cortex control functions + * @verbatim ============================================================================== ##### Peripheral Control functions ##### @@ -263,6 +251,46 @@ uint32_t HAL_SYSTICK_Config(uint32_t TicksNumb) */ #if (__MPU_PRESENT == 1U) +/** + * @brief Disables the MPU + * @retval None + */ +void HAL_MPU_Disable(void) +{ + /* Make sure outstanding transfers are done */ + __DMB(); + + /* Disable fault exceptions */ + SCB->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk; + + /* Disable the MPU and clear the control register*/ + MPU->CTRL = 0U; +} + +/** + * @brief Enable the MPU. + * @param MPU_Control: Specifies the control mode of the MPU during hard fault, + * NMI, FAULTMASK and privileged access to the default memory + * This parameter can be one of the following values: + * @arg MPU_HFNMI_PRIVDEF_NONE + * @arg MPU_HARDFAULT_NMI + * @arg MPU_PRIVILEGED_DEFAULT + * @arg MPU_HFNMI_PRIVDEF + * @retval None + */ +void HAL_MPU_Enable(uint32_t MPU_Control) +{ + /* Enable the MPU */ + MPU->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk; + + /* Enable fault exceptions */ + SCB->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk; + + /* Ensure MPU setting take effects */ + __DSB(); + __ISB(); +} + /** * @brief Initializes and configures the Region and the memory to be protected. * @param MPU_Init: Pointer to a MPU_Region_InitTypeDef structure that contains @@ -274,6 +302,7 @@ void HAL_MPU_ConfigRegion(MPU_Region_InitTypeDef* MPU_Init) /* Check the parameters */ assert_param(IS_MPU_REGION_NUMBER(MPU_Init->Number)); assert_param(IS_MPU_REGION_ENABLE(MPU_Init->Enable)); + /* Set the Region number */ MPU->RNR = MPU_Init->Number; @@ -288,6 +317,7 @@ void HAL_MPU_ConfigRegion(MPU_Region_InitTypeDef* MPU_Init) assert_param(IS_MPU_ACCESS_BUFFERABLE(MPU_Init->IsBufferable)); assert_param(IS_MPU_SUB_REGION_DISABLE(MPU_Init->SubRegionDisable)); assert_param(IS_MPU_REGION_SIZE(MPU_Init->Size)); + MPU->RBAR = MPU_Init->BaseAddress; MPU->RASR = ((uint32_t)MPU_Init->DisableExec << MPU_RASR_XN_Pos) | ((uint32_t)MPU_Init->AccessPermission << MPU_RASR_AP_Pos) | @@ -321,7 +351,7 @@ uint32_t HAL_NVIC_GetPriorityGrouping(void) * @brief Gets the priority of an interrupt. * @param IRQn: External interrupt number. * This parameter can be an enumerator of IRQn_Type enumeration - * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xxx.h)) * @param PriorityGroup: the priority grouping bits length. * This parameter can be one of the following values: * @arg NVIC_PRIORITYGROUP_0: 0 bits for preemption priority @@ -350,13 +380,14 @@ void HAL_NVIC_GetPriority(IRQn_Type IRQn, uint32_t PriorityGroup, uint32_t* pPre * @brief Sets Pending bit of an external interrupt. * @param IRQn External interrupt number * This parameter can be an enumerator of IRQn_Type enumeration - * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xxx.h)) * @retval None */ void HAL_NVIC_SetPendingIRQ(IRQn_Type IRQn) { /* Check the parameters */ assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); + /* Set interrupt pending */ NVIC_SetPendingIRQ(IRQn); } @@ -365,8 +396,8 @@ void HAL_NVIC_SetPendingIRQ(IRQn_Type IRQn) * @brief Gets Pending Interrupt (reads the pending register in the NVIC * and returns the pending bit for the specified interrupt). * @param IRQn External interrupt number. - * This parameter can be an enumerator of IRQn_Type enumeration - * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xxx.h)) * @retval status: - 0 Interrupt status is not pending. * - 1 Interrupt status is pending. */ @@ -374,6 +405,7 @@ uint32_t HAL_NVIC_GetPendingIRQ(IRQn_Type IRQn) { /* Check the parameters */ assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); + /* Return 1 if pending else 0 */ return NVIC_GetPendingIRQ(IRQn); } @@ -382,13 +414,14 @@ uint32_t HAL_NVIC_GetPendingIRQ(IRQn_Type IRQn) * @brief Clears the pending bit of an external interrupt. * @param IRQn External interrupt number. * This parameter can be an enumerator of IRQn_Type enumeration - * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xxx.h)) * @retval None */ void HAL_NVIC_ClearPendingIRQ(IRQn_Type IRQn) { /* Check the parameters */ assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); + /* Clear pending interrupt */ NVIC_ClearPendingIRQ(IRQn); } @@ -397,7 +430,7 @@ void HAL_NVIC_ClearPendingIRQ(IRQn_Type IRQn) * @brief Gets active interrupt ( reads the active register in NVIC and returns the active bit). * @param IRQn External interrupt number * This parameter can be an enumerator of IRQn_Type enumeration - * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xxx.h)) * @retval status: - 0 Interrupt status is not pending. * - 1 Interrupt status is pending. */ @@ -405,6 +438,7 @@ uint32_t HAL_NVIC_GetActive(IRQn_Type IRQn) { /* Check the parameters */ assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); + /* Return 1 if active else 0 */ return NVIC_GetActive(IRQn); } @@ -412,7 +446,7 @@ uint32_t HAL_NVIC_GetActive(IRQn_Type IRQn) /** * @brief Configures the SysTick clock source. * @param CLKSource: specifies the SysTick clock source. - * This parameter can be one of the following values: + * This parameter can be one of the following values: * @arg SYSTICK_CLKSOURCE_HCLK_DIV8: AHB clock divided by 8 selected as SysTick clock source. * @arg SYSTICK_CLKSOURCE_HCLK: AHB clock selected as SysTick clock source. * @retval None diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_dma.c b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_dma.c new file mode 100644 index 00000000..ed651495 --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_dma.c @@ -0,0 +1,912 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_dma.c + * @author MCD Application Team + * @brief DMA HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Direct Memory Access (DMA) peripheral: + * + Initialization and de-initialization functions + * + IO operation functions + * + Peripheral State and errors functions + @verbatim + ============================================================================== + ##### How to use this driver ##### + ============================================================================== + [..] + (#) Enable and configure the peripheral to be connected to the DMA Channel + (except for internal SRAM / FLASH memories: no initialization is + necessary). Please refer to the Reference manual for connection between peripherals + and DMA requests. + + (#) For a given Channel, program the required configuration through the following parameters: + Channel request, Transfer Direction, Source and Destination data formats, + Circular or Normal mode, Channel Priority level, Source and Destination Increment mode + using HAL_DMA_Init() function. + + (#) Use HAL_DMA_GetState() function to return the DMA state and HAL_DMA_GetError() in case of error + detection. + + (#) Use HAL_DMA_Abort() function to abort the current transfer + + -@- In Memory-to-Memory transfer mode, Circular mode is not allowed. + *** Polling mode IO operation *** + ================================= + [..] + (+) Use HAL_DMA_Start() to start DMA transfer after the configuration of Source + address and destination address and the Length of data to be transferred + (+) Use HAL_DMA_PollForTransfer() to poll for the end of current transfer, in this + case a fixed Timeout can be configured by User depending from his application. + + *** Interrupt mode IO operation *** + =================================== + [..] + (+) Configure the DMA interrupt priority using HAL_NVIC_SetPriority() + (+) Enable the DMA IRQ handler using HAL_NVIC_EnableIRQ() + (+) Use HAL_DMA_Start_IT() to start DMA transfer after the configuration of + Source address and destination address and the Length of data to be transferred. + In this case the DMA interrupt is configured + (+) Use HAL_DMA_IRQHandler() called under DMA_IRQHandler() Interrupt subroutine + (+) At the end of data transfer HAL_DMA_IRQHandler() function is executed and user can + add his own function by customization of function pointer XferCpltCallback and + XferErrorCallback (i.e. a member of DMA handle structure). + + *** DMA HAL driver macros list *** + ============================================= + [..] + Below the list of most used macros in DMA HAL driver. + + (+) __HAL_DMA_ENABLE: Enable the specified DMA Channel. + (+) __HAL_DMA_DISABLE: Disable the specified DMA Channel. + (+) __HAL_DMA_GET_FLAG: Get the DMA Channel pending flags. + (+) __HAL_DMA_CLEAR_FLAG: Clear the DMA Channel pending flags. + (+) __HAL_DMA_ENABLE_IT: Enable the specified DMA Channel interrupts. + (+) __HAL_DMA_DISABLE_IT: Disable the specified DMA Channel interrupts. + (+) __HAL_DMA_GET_IT_SOURCE: Check whether the specified DMA Channel interrupt has occurred or not. + + [..] + (@) You can refer to the DMA HAL driver header file for more useful macros + + @endverbatim + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @defgroup DMA DMA + * @brief DMA HAL module driver + * @{ + */ + +#ifdef HAL_DMA_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/** @defgroup DMA_Private_Functions DMA Private Functions + * @{ + */ +static void DMA_SetConfig(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength); +/** + * @} + */ + +/* Exported functions ---------------------------------------------------------*/ + +/** @defgroup DMA_Exported_Functions DMA Exported Functions + * @{ + */ + +/** @defgroup DMA_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and de-initialization functions + * +@verbatim + =============================================================================== + ##### Initialization and de-initialization functions ##### + =============================================================================== + [..] + This section provides functions allowing to initialize the DMA Channel source + and destination addresses, incrementation and data sizes, transfer direction, + circular/normal mode selection, memory-to-memory mode selection and Channel priority value. + [..] + The HAL_DMA_Init() function follows the DMA configuration procedures as described in + reference manual. + +@endverbatim + * @{ + */ + +/** + * @brief Initialize the DMA according to the specified + * parameters in the DMA_InitTypeDef and initialize the associated handle. + * @param hdma: Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA Channel. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_DMA_Init(DMA_HandleTypeDef* hdma) +{ + uint32_t tmp = 0U; + + /* Check the DMA handle allocation */ + if (hdma == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_DMA_ALL_INSTANCE(hdma->Instance)); + assert_param(IS_DMA_DIRECTION(hdma->Init.Direction)); + assert_param(IS_DMA_PERIPHERAL_INC_STATE(hdma->Init.PeriphInc)); + assert_param(IS_DMA_MEMORY_INC_STATE(hdma->Init.MemInc)); + assert_param(IS_DMA_PERIPHERAL_DATA_SIZE(hdma->Init.PeriphDataAlignment)); + assert_param(IS_DMA_MEMORY_DATA_SIZE(hdma->Init.MemDataAlignment)); + assert_param(IS_DMA_MODE(hdma->Init.Mode)); + assert_param(IS_DMA_PRIORITY(hdma->Init.Priority)); + +#if defined (DMA2) + + /* calculation of the channel index */ + if ((uint32_t)(hdma->Instance) < (uint32_t)(DMA2_Channel1)) + { + /* DMA1 */ + hdma->ChannelIndex = (((uint32_t)hdma->Instance - (uint32_t)DMA1_Channel1) / ((uint32_t)DMA1_Channel2 - (uint32_t)DMA1_Channel1)) << 2; + hdma->DmaBaseAddress = DMA1; + } + else + { + /* DMA2 */ + hdma->ChannelIndex = (((uint32_t)hdma->Instance - (uint32_t)DMA2_Channel1) / ((uint32_t)DMA2_Channel2 - (uint32_t)DMA2_Channel1)) << 2; + hdma->DmaBaseAddress = DMA2; + } + +#else + /* DMA1 */ + hdma->ChannelIndex = (((uint32_t)hdma->Instance - (uint32_t)DMA1_Channel1) / ((uint32_t)DMA1_Channel2 - (uint32_t)DMA1_Channel1)) << 2; + hdma->DmaBaseAddress = DMA1; +#endif /* DMA2 */ + + /* Change DMA peripheral state */ + hdma->State = HAL_DMA_STATE_BUSY; + + /* Get the CR register value */ + tmp = hdma->Instance->CCR; + + /* Clear PL, MSIZE, PSIZE, MINC, PINC, CIRC and DIR bits */ + tmp &= ((uint32_t)~(DMA_CCR_PL | DMA_CCR_MSIZE | DMA_CCR_PSIZE | \ + DMA_CCR_MINC | DMA_CCR_PINC | DMA_CCR_CIRC | \ + DMA_CCR_DIR)); + + /* Prepare the DMA Channel configuration */ + tmp |= hdma->Init.Direction | + hdma->Init.PeriphInc | hdma->Init.MemInc | + hdma->Init.PeriphDataAlignment | hdma->Init.MemDataAlignment | + hdma->Init.Mode | hdma->Init.Priority; + + /* Write to DMA Channel CR register */ + hdma->Instance->CCR = tmp; + + /* Initialise the error code */ + hdma->ErrorCode = HAL_DMA_ERROR_NONE; + + /* Initialize the DMA state*/ + hdma->State = HAL_DMA_STATE_READY; + /* Allocate lock resource and initialize it */ + hdma->Lock = HAL_UNLOCKED; + + return HAL_OK; +} + +/** + * @brief DeInitialize the DMA peripheral. + * @param hdma: pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA Channel. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_DMA_DeInit(DMA_HandleTypeDef* hdma) +{ + /* Check the DMA handle allocation */ + if (hdma == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_DMA_ALL_INSTANCE(hdma->Instance)); + + /* Disable the selected DMA Channelx */ + __HAL_DMA_DISABLE(hdma); + + /* Reset DMA Channel control register */ + hdma->Instance->CCR = 0U; + + /* Reset DMA Channel Number of Data to Transfer register */ + hdma->Instance->CNDTR = 0U; + + /* Reset DMA Channel peripheral address register */ + hdma->Instance->CPAR = 0U; + + /* Reset DMA Channel memory address register */ + hdma->Instance->CMAR = 0U; + +#if defined (DMA2) + + /* calculation of the channel index */ + if ((uint32_t)(hdma->Instance) < (uint32_t)(DMA2_Channel1)) + { + /* DMA1 */ + hdma->ChannelIndex = (((uint32_t)hdma->Instance - (uint32_t)DMA1_Channel1) / ((uint32_t)DMA1_Channel2 - (uint32_t)DMA1_Channel1)) << 2; + hdma->DmaBaseAddress = DMA1; + } + else + { + /* DMA2 */ + hdma->ChannelIndex = (((uint32_t)hdma->Instance - (uint32_t)DMA2_Channel1) / ((uint32_t)DMA2_Channel2 - (uint32_t)DMA2_Channel1)) << 2; + hdma->DmaBaseAddress = DMA2; + } + +#else + /* DMA1 */ + hdma->ChannelIndex = (((uint32_t)hdma->Instance - (uint32_t)DMA1_Channel1) / ((uint32_t)DMA1_Channel2 - (uint32_t)DMA1_Channel1)) << 2; + hdma->DmaBaseAddress = DMA1; +#endif /* DMA2 */ + + /* Clear all flags */ + hdma->DmaBaseAddress->IFCR = (DMA_ISR_GIF1 << (hdma->ChannelIndex)); + + /* Clean all callbacks */ + hdma->XferCpltCallback = NULL; + hdma->XferHalfCpltCallback = NULL; + hdma->XferErrorCallback = NULL; + hdma->XferAbortCallback = NULL; + + /* Reset the error code */ + hdma->ErrorCode = HAL_DMA_ERROR_NONE; + + /* Reset the DMA state */ + hdma->State = HAL_DMA_STATE_RESET; + + /* Release Lock */ + __HAL_UNLOCK(hdma); + + return HAL_OK; +} + +/** + * @} + */ + +/** @defgroup DMA_Exported_Functions_Group2 Input and Output operation functions + * @brief Input and Output operation functions + * +@verbatim + =============================================================================== + ##### IO operation functions ##### + =============================================================================== + [..] This section provides functions allowing to: + (+) Configure the source, destination address and data length and Start DMA transfer + (+) Configure the source, destination address and data length and + Start DMA transfer with interrupt + (+) Abort DMA transfer + (+) Poll for transfer complete + (+) Handle DMA interrupt request + +@endverbatim + * @{ + */ + +/** + * @brief Start the DMA Transfer. + * @param hdma: pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA Channel. + * @param SrcAddress: The source memory Buffer address + * @param DstAddress: The destination memory Buffer address + * @param DataLength: The length of data to be transferred from source to destination + * @retval HAL status + */ +HAL_StatusTypeDef HAL_DMA_Start(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength) +{ + HAL_StatusTypeDef status = HAL_OK; + + /* Check the parameters */ + assert_param(IS_DMA_BUFFER_SIZE(DataLength)); + + /* Process locked */ + __HAL_LOCK(hdma); + + if (HAL_DMA_STATE_READY == hdma->State) + { + /* Change DMA peripheral state */ + hdma->State = HAL_DMA_STATE_BUSY; + hdma->ErrorCode = HAL_DMA_ERROR_NONE; + + /* Disable the peripheral */ + __HAL_DMA_DISABLE(hdma); + + /* Configure the source, destination address and the data length & clear flags*/ + DMA_SetConfig(hdma, SrcAddress, DstAddress, DataLength); + + /* Enable the Peripheral */ + __HAL_DMA_ENABLE(hdma); + } + else + { + /* Process Unlocked */ + __HAL_UNLOCK(hdma); + status = HAL_BUSY; + } + + return status; +} + +/** + * @brief Start the DMA Transfer with interrupt enabled. + * @param hdma: pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA Channel. + * @param SrcAddress: The source memory Buffer address + * @param DstAddress: The destination memory Buffer address + * @param DataLength: The length of data to be transferred from source to destination + * @retval HAL status + */ +HAL_StatusTypeDef HAL_DMA_Start_IT(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength) +{ + HAL_StatusTypeDef status = HAL_OK; + + /* Check the parameters */ + assert_param(IS_DMA_BUFFER_SIZE(DataLength)); + + /* Process locked */ + __HAL_LOCK(hdma); + + if (HAL_DMA_STATE_READY == hdma->State) + { + /* Change DMA peripheral state */ + hdma->State = HAL_DMA_STATE_BUSY; + hdma->ErrorCode = HAL_DMA_ERROR_NONE; + + /* Disable the peripheral */ + __HAL_DMA_DISABLE(hdma); + + /* Configure the source, destination address and the data length & clear flags*/ + DMA_SetConfig(hdma, SrcAddress, DstAddress, DataLength); + + /* Enable the transfer complete interrupt */ + /* Enable the transfer Error interrupt */ + if (NULL != hdma->XferHalfCpltCallback) + { + /* Enable the Half transfer complete interrupt as well */ + __HAL_DMA_ENABLE_IT(hdma, (DMA_IT_TC | DMA_IT_HT | DMA_IT_TE)); + } + else + { + __HAL_DMA_DISABLE_IT(hdma, DMA_IT_HT); + __HAL_DMA_ENABLE_IT(hdma, (DMA_IT_TC | DMA_IT_TE)); + } + + /* Enable the Peripheral */ + __HAL_DMA_ENABLE(hdma); + } + else + { + /* Process Unlocked */ + __HAL_UNLOCK(hdma); + + /* Remain BUSY */ + status = HAL_BUSY; + } + + return status; +} + +/** + * @brief Abort the DMA Transfer. + * @param hdma: pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA Channel. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_DMA_Abort(DMA_HandleTypeDef* hdma) +{ + HAL_StatusTypeDef status = HAL_OK; + + if (hdma->State != HAL_DMA_STATE_BUSY) + { + /* no transfer ongoing */ + hdma->ErrorCode = HAL_DMA_ERROR_NO_XFER; + + /* Process Unlocked */ + __HAL_UNLOCK(hdma); + + return HAL_ERROR; + } + else + + { + /* Disable DMA IT */ + __HAL_DMA_DISABLE_IT(hdma, (DMA_IT_TC | DMA_IT_HT | DMA_IT_TE)); + + /* Disable the channel */ + __HAL_DMA_DISABLE(hdma); + + /* Clear all flags */ + hdma->DmaBaseAddress->IFCR = (DMA_ISR_GIF1 << hdma->ChannelIndex); + } + + /* Change the DMA state */ + hdma->State = HAL_DMA_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hdma); + + return status; +} + +/** + * @brief Aborts the DMA Transfer in Interrupt mode. + * @param hdma : pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA Channel. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_DMA_Abort_IT(DMA_HandleTypeDef* hdma) +{ + HAL_StatusTypeDef status = HAL_OK; + + if (HAL_DMA_STATE_BUSY != hdma->State) + { + /* no transfer ongoing */ + hdma->ErrorCode = HAL_DMA_ERROR_NO_XFER; + + status = HAL_ERROR; + } + else + { + /* Disable DMA IT */ + __HAL_DMA_DISABLE_IT(hdma, (DMA_IT_TC | DMA_IT_HT | DMA_IT_TE)); + + /* Disable the channel */ + __HAL_DMA_DISABLE(hdma); + + /* Clear all flags */ + __HAL_DMA_CLEAR_FLAG(hdma, __HAL_DMA_GET_GI_FLAG_INDEX(hdma)); + + /* Change the DMA state */ + hdma->State = HAL_DMA_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hdma); + + /* Call User Abort callback */ + if (hdma->XferAbortCallback != NULL) + { + hdma->XferAbortCallback(hdma); + } + } + + return status; +} + +/** + * @brief Polling for transfer complete. + * @param hdma: pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA Channel. + * @param CompleteLevel: Specifies the DMA level complete. + * @param Timeout: Timeout duration. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_DMA_PollForTransfer(DMA_HandleTypeDef* hdma, uint32_t CompleteLevel, uint32_t Timeout) +{ + uint32_t temp; + uint32_t tickstart = 0U; + + if (HAL_DMA_STATE_BUSY != hdma->State) + { + /* no transfer ongoing */ + hdma->ErrorCode = HAL_DMA_ERROR_NO_XFER; + __HAL_UNLOCK(hdma); + return HAL_ERROR; + } + + /* Polling mode not supported in circular mode */ + if (RESET != (hdma->Instance->CCR & DMA_CCR_CIRC)) + { + hdma->ErrorCode = HAL_DMA_ERROR_NOT_SUPPORTED; + return HAL_ERROR; + } + + /* Get the level transfer complete flag */ + if (CompleteLevel == HAL_DMA_FULL_TRANSFER) + { + /* Transfer Complete flag */ + temp = __HAL_DMA_GET_TC_FLAG_INDEX(hdma); + } + else + { + /* Half Transfer Complete flag */ + temp = __HAL_DMA_GET_HT_FLAG_INDEX(hdma); + } + + /* Get tick */ + tickstart = HAL_GetTick(); + + while (__HAL_DMA_GET_FLAG(hdma, temp) == RESET) + { + if ((__HAL_DMA_GET_FLAG(hdma, __HAL_DMA_GET_TE_FLAG_INDEX(hdma)) != RESET)) + { + /* When a DMA transfer error occurs */ + /* A hardware clear of its EN bits is performed */ + /* Clear all flags */ + hdma->DmaBaseAddress->IFCR = (DMA_ISR_GIF1 << hdma->ChannelIndex); + + /* Update error code */ + SET_BIT(hdma->ErrorCode, HAL_DMA_ERROR_TE); + + /* Change the DMA state */ + hdma->State = HAL_DMA_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hdma); + + return HAL_ERROR; + } + + /* Check for the Timeout */ + if (Timeout != HAL_MAX_DELAY) + { + if ((Timeout == 0U) || ((HAL_GetTick() - tickstart) > Timeout)) + { + /* Update error code */ + SET_BIT(hdma->ErrorCode, HAL_DMA_ERROR_TIMEOUT); + + /* Change the DMA state */ + hdma->State = HAL_DMA_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hdma); + + return HAL_ERROR; + } + } + } + + if (CompleteLevel == HAL_DMA_FULL_TRANSFER) + { + /* Clear the transfer complete flag */ + __HAL_DMA_CLEAR_FLAG(hdma, __HAL_DMA_GET_TC_FLAG_INDEX(hdma)); + + /* The selected Channelx EN bit is cleared (DMA is disabled and + all transfers are complete) */ + hdma->State = HAL_DMA_STATE_READY; + } + else + { + /* Clear the half transfer complete flag */ + __HAL_DMA_CLEAR_FLAG(hdma, __HAL_DMA_GET_HT_FLAG_INDEX(hdma)); + } + + /* Process unlocked */ + __HAL_UNLOCK(hdma); + + return HAL_OK; +} + +/** + * @brief Handles DMA interrupt request. + * @param hdma: pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA Channel. + * @retval None + */ +void HAL_DMA_IRQHandler(DMA_HandleTypeDef* hdma) +{ + uint32_t flag_it = hdma->DmaBaseAddress->ISR; + uint32_t source_it = hdma->Instance->CCR; + + /* Half Transfer Complete Interrupt management ******************************/ + if (((flag_it & (DMA_FLAG_HT1 << hdma->ChannelIndex)) != RESET) && ((source_it & DMA_IT_HT) != RESET)) + { + /* Disable the half transfer interrupt if the DMA mode is not CIRCULAR */ + if ((hdma->Instance->CCR & DMA_CCR_CIRC) == 0U) + { + /* Disable the half transfer interrupt */ + __HAL_DMA_DISABLE_IT(hdma, DMA_IT_HT); + } + + /* Clear the half transfer complete flag */ + __HAL_DMA_CLEAR_FLAG(hdma, __HAL_DMA_GET_HT_FLAG_INDEX(hdma)); + + /* DMA peripheral state is not updated in Half Transfer */ + /* but in Transfer Complete case */ + + if (hdma->XferHalfCpltCallback != NULL) + { + /* Half transfer callback */ + hdma->XferHalfCpltCallback(hdma); + } + } + + /* Transfer Complete Interrupt management ***********************************/ + else if (((flag_it & (DMA_FLAG_TC1 << hdma->ChannelIndex)) != RESET) && ((source_it & DMA_IT_TC) != RESET)) + { + if ((hdma->Instance->CCR & DMA_CCR_CIRC) == 0U) + { + /* Disable the transfer complete and error interrupt */ + __HAL_DMA_DISABLE_IT(hdma, DMA_IT_TE | DMA_IT_TC); + + /* Change the DMA state */ + hdma->State = HAL_DMA_STATE_READY; + } + + /* Clear the transfer complete flag */ + __HAL_DMA_CLEAR_FLAG(hdma, __HAL_DMA_GET_TC_FLAG_INDEX(hdma)); + + /* Process Unlocked */ + __HAL_UNLOCK(hdma); + + if (hdma->XferCpltCallback != NULL) + { + /* Transfer complete callback */ + hdma->XferCpltCallback(hdma); + } + } + + /* Transfer Error Interrupt management **************************************/ + else if (( RESET != (flag_it & (DMA_FLAG_TE1 << hdma->ChannelIndex))) && (RESET != (source_it & DMA_IT_TE))) + { + /* When a DMA transfer error occurs */ + /* A hardware clear of its EN bits is performed */ + /* Disable ALL DMA IT */ + __HAL_DMA_DISABLE_IT(hdma, (DMA_IT_TC | DMA_IT_HT | DMA_IT_TE)); + + /* Clear all flags */ + hdma->DmaBaseAddress->IFCR = (DMA_ISR_GIF1 << hdma->ChannelIndex); + + /* Update error code */ + hdma->ErrorCode = HAL_DMA_ERROR_TE; + + /* Change the DMA state */ + hdma->State = HAL_DMA_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hdma); + + if (hdma->XferErrorCallback != NULL) + { + /* Transfer error callback */ + hdma->XferErrorCallback(hdma); + } + } + + return; +} + +/** + * @brief Register callbacks + * @param hdma: pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA Channel. + * @param CallbackID: User Callback identifer + * a HAL_DMA_CallbackIDTypeDef ENUM as parameter. + * @param pCallback: pointer to private callbacsk function which has pointer to + * a DMA_HandleTypeDef structure as parameter. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_DMA_RegisterCallback(DMA_HandleTypeDef* hdma, HAL_DMA_CallbackIDTypeDef CallbackID, void (* pCallback)( DMA_HandleTypeDef* _hdma)) +{ + HAL_StatusTypeDef status = HAL_OK; + + /* Process locked */ + __HAL_LOCK(hdma); + + if (HAL_DMA_STATE_READY == hdma->State) + { + switch (CallbackID) + { + case HAL_DMA_XFER_CPLT_CB_ID: + hdma->XferCpltCallback = pCallback; + break; + + case HAL_DMA_XFER_HALFCPLT_CB_ID: + hdma->XferHalfCpltCallback = pCallback; + break; + + case HAL_DMA_XFER_ERROR_CB_ID: + hdma->XferErrorCallback = pCallback; + break; + + case HAL_DMA_XFER_ABORT_CB_ID: + hdma->XferAbortCallback = pCallback; + break; + + default: + status = HAL_ERROR; + break; + } + } + else + { + status = HAL_ERROR; + } + + /* Release Lock */ + __HAL_UNLOCK(hdma); + + return status; +} + +/** + * @brief UnRegister callbacks + * @param hdma: pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA Channel. + * @param CallbackID: User Callback identifer + * a HAL_DMA_CallbackIDTypeDef ENUM as parameter. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_DMA_UnRegisterCallback(DMA_HandleTypeDef* hdma, HAL_DMA_CallbackIDTypeDef CallbackID) +{ + HAL_StatusTypeDef status = HAL_OK; + + /* Process locked */ + __HAL_LOCK(hdma); + + if (HAL_DMA_STATE_READY == hdma->State) + { + switch (CallbackID) + { + case HAL_DMA_XFER_CPLT_CB_ID: + hdma->XferCpltCallback = NULL; + break; + + case HAL_DMA_XFER_HALFCPLT_CB_ID: + hdma->XferHalfCpltCallback = NULL; + break; + + case HAL_DMA_XFER_ERROR_CB_ID: + hdma->XferErrorCallback = NULL; + break; + + case HAL_DMA_XFER_ABORT_CB_ID: + hdma->XferAbortCallback = NULL; + break; + + case HAL_DMA_XFER_ALL_CB_ID: + hdma->XferCpltCallback = NULL; + hdma->XferHalfCpltCallback = NULL; + hdma->XferErrorCallback = NULL; + hdma->XferAbortCallback = NULL; + break; + + default: + status = HAL_ERROR; + break; + } + } + else + { + status = HAL_ERROR; + } + + /* Release Lock */ + __HAL_UNLOCK(hdma); + + return status; +} + +/** + * @} + */ + +/** @defgroup DMA_Exported_Functions_Group3 Peripheral State and Errors functions + * @brief Peripheral State and Errors functions + * +@verbatim + =============================================================================== + ##### Peripheral State and Errors functions ##### + =============================================================================== + [..] + This subsection provides functions allowing to + (+) Check the DMA state + (+) Get error code + +@endverbatim + * @{ + */ + +/** + * @brief Return the DMA hande state. + * @param hdma: pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA Channel. + * @retval HAL state + */ +HAL_DMA_StateTypeDef HAL_DMA_GetState(DMA_HandleTypeDef* hdma) +{ + /* Return DMA handle state */ + return hdma->State; +} + +/** + * @brief Return the DMA error code. + * @param hdma : pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA Channel. + * @retval DMA Error Code + */ +uint32_t HAL_DMA_GetError(DMA_HandleTypeDef* hdma) +{ + return hdma->ErrorCode; +} + +/** + * @} + */ + +/** + * @} + */ + +/** @addtogroup DMA_Private_Functions + * @{ + */ + +/** + * @brief Sets the DMA Transfer parameter. + * @param hdma: pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA Channel. + * @param SrcAddress: The source memory Buffer address + * @param DstAddress: The destination memory Buffer address + * @param DataLength: The length of data to be transferred from source to destination + * @retval HAL status + */ +static void DMA_SetConfig(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength) +{ + /* Clear all flags */ + hdma->DmaBaseAddress->IFCR = (DMA_ISR_GIF1 << hdma->ChannelIndex); + + /* Configure DMA Channel data length */ + hdma->Instance->CNDTR = DataLength; + + /* Memory to Peripheral */ + if ((hdma->Init.Direction) == DMA_MEMORY_TO_PERIPH) + { + /* Configure DMA Channel destination address */ + hdma->Instance->CPAR = DstAddress; + + /* Configure DMA Channel source address */ + hdma->Instance->CMAR = SrcAddress; + } + /* Peripheral to Memory */ + else + { + /* Configure DMA Channel source address */ + hdma->Instance->CPAR = SrcAddress; + + /* Configure DMA Channel destination address */ + hdma->Instance->CMAR = DstAddress; + } +} + +/** + * @} + */ + +#endif /* HAL_DMA_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_exti.c b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_exti.c new file mode 100644 index 00000000..5f432170 --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_exti.c @@ -0,0 +1,560 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_exti.c + * @author MCD Application Team + * @brief EXTI HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Extended Interrupts and events controller (EXTI) peripheral: + * + Initialization and de-initialization functions + * + IO operation functions + * + @verbatim + ============================================================================== + ##### EXTI Peripheral features ##### + ============================================================================== + [..] + (+) Each Exti line can be configured within this driver. + + (+) Exti line can be configured in 3 different modes + (++) Interrupt + (++) Event + (++) Both of them + + (+) Configurable Exti lines can be configured with 3 different triggers + (++) Rising + (++) Falling + (++) Both of them + + (+) When set in interrupt mode, configurable Exti lines have two different + interrupts pending registers which allow to distinguish which transition + occurs: + (++) Rising edge pending interrupt + (++) Falling + + (+) Exti lines 0 to 15 are linked to gpio pin number 0 to 15. Gpio port can + be selected through multiplexer. + + ##### How to use this driver ##### + ============================================================================== + [..] + + (#) Configure the EXTI line using HAL_EXTI_SetConfigLine(). + (++) Choose the interrupt line number by setting "Line" member from + EXTI_ConfigTypeDef structure. + (++) Configure the interrupt and/or event mode using "Mode" member from + EXTI_ConfigTypeDef structure. + (++) For configurable lines, configure rising and/or falling trigger + "Trigger" member from EXTI_ConfigTypeDef structure. + (++) For Exti lines linked to gpio, choose gpio port using "GPIOSel" + member from GPIO_InitTypeDef structure. + + (#) Get current Exti configuration of a dedicated line using + HAL_EXTI_GetConfigLine(). + (++) Provide exiting handle as parameter. + (++) Provide pointer on EXTI_ConfigTypeDef structure as second parameter. + + (#) Clear Exti configuration of a dedicated line using HAL_EXTI_GetConfigLine(). + (++) Provide exiting handle as parameter. + + (#) Register callback to treat Exti interrupts using HAL_EXTI_RegisterCallback(). + (++) Provide exiting handle as first parameter. + (++) Provide which callback will be registered using one value from + EXTI_CallbackIDTypeDef. + (++) Provide callback function pointer. + + (#) Get interrupt pending bit using HAL_EXTI_GetPending(). + + (#) Clear interrupt pending bit using HAL_EXTI_GetPending(). + + (#) Generate software interrupt using HAL_EXTI_GenerateSWI(). + + @endverbatim + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2019 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @addtogroup EXTI + * @{ + */ +/** MISRA C:2012 deviation rule has been granted for following rule: + * Rule-18.1_b - Medium: Array `EXTICR' 1st subscript interval [0,7] may be out + * of bounds [0,3] in following API : + * HAL_EXTI_SetConfigLine + * HAL_EXTI_GetConfigLine + * HAL_EXTI_ClearConfigLine + */ + +#ifdef HAL_EXTI_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private defines -----------------------------------------------------------*/ +/** @defgroup EXTI_Private_Constants EXTI Private Constants + * @{ + */ + +/** + * @} + */ + +/* Private macros ------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Exported functions --------------------------------------------------------*/ + +/** @addtogroup EXTI_Exported_Functions + * @{ + */ + +/** @addtogroup EXTI_Exported_Functions_Group1 + * @brief Configuration functions + * +@verbatim + =============================================================================== + ##### Configuration functions ##### + =============================================================================== + +@endverbatim + * @{ + */ + +/** + * @brief Set configuration of a dedicated Exti line. + * @param hexti Exti handle. + * @param pExtiConfig Pointer on EXTI configuration to be set. + * @retval HAL Status. + */ +HAL_StatusTypeDef HAL_EXTI_SetConfigLine(EXTI_HandleTypeDef* hexti, EXTI_ConfigTypeDef* pExtiConfig) +{ + uint32_t regval; + uint32_t linepos; + uint32_t maskline; + + /* Check null pointer */ + if ((hexti == NULL) || (pExtiConfig == NULL)) + { + return HAL_ERROR; + } + + /* Check parameters */ + assert_param(IS_EXTI_LINE(pExtiConfig->Line)); + assert_param(IS_EXTI_MODE(pExtiConfig->Mode)); + + /* Assign line number to handle */ + hexti->Line = pExtiConfig->Line; + + /* Compute line mask */ + linepos = (pExtiConfig->Line & EXTI_PIN_MASK); + maskline = (1uL << linepos); + + /* Configure triggers for configurable lines */ + if ((pExtiConfig->Line & EXTI_CONFIG) != 0x00u) + { + assert_param(IS_EXTI_TRIGGER(pExtiConfig->Trigger)); + + /* Configure rising trigger */ + /* Mask or set line */ + if ((pExtiConfig->Trigger & EXTI_TRIGGER_RISING) != 0x00u) + { + EXTI->RTSR |= maskline; + } + else + { + EXTI->RTSR &= ~maskline; + } + + /* Configure falling trigger */ + /* Mask or set line */ + if ((pExtiConfig->Trigger & EXTI_TRIGGER_FALLING) != 0x00u) + { + EXTI->FTSR |= maskline; + } + else + { + EXTI->FTSR &= ~maskline; + } + + + /* Configure gpio port selection in case of gpio exti line */ + if ((pExtiConfig->Line & EXTI_GPIO) == EXTI_GPIO) + { + assert_param(IS_EXTI_GPIO_PORT(pExtiConfig->GPIOSel)); + assert_param(IS_EXTI_GPIO_PIN(linepos)); + + regval = AFIO->EXTICR[linepos >> 2u]; + regval &= ~(AFIO_EXTICR1_EXTI0 << (AFIO_EXTICR1_EXTI1_Pos * (linepos & 0x03u))); + regval |= (pExtiConfig->GPIOSel << (AFIO_EXTICR1_EXTI1_Pos * (linepos & 0x03u))); + AFIO->EXTICR[linepos >> 2u] = regval; + } + } + + /* Configure interrupt mode : read current mode */ + /* Mask or set line */ + if ((pExtiConfig->Mode & EXTI_MODE_INTERRUPT) != 0x00u) + { + EXTI->IMR |= maskline; + } + else + { + EXTI->IMR &= ~maskline; + } + + /* Configure event mode : read current mode */ + /* Mask or set line */ + if ((pExtiConfig->Mode & EXTI_MODE_EVENT) != 0x00u) + { + EXTI->EMR |= maskline; + } + else + { + EXTI->EMR &= ~maskline; + } + + return HAL_OK; +} + +/** + * @brief Get configuration of a dedicated Exti line. + * @param hexti Exti handle. + * @param pExtiConfig Pointer on structure to store Exti configuration. + * @retval HAL Status. + */ +HAL_StatusTypeDef HAL_EXTI_GetConfigLine(EXTI_HandleTypeDef* hexti, EXTI_ConfigTypeDef* pExtiConfig) +{ + uint32_t regval; + uint32_t linepos; + uint32_t maskline; + + /* Check null pointer */ + if ((hexti == NULL) || (pExtiConfig == NULL)) + { + return HAL_ERROR; + } + + /* Check the parameter */ + assert_param(IS_EXTI_LINE(hexti->Line)); + + /* Store handle line number to configuration structure */ + pExtiConfig->Line = hexti->Line; + + /* Compute line mask */ + linepos = (pExtiConfig->Line & EXTI_PIN_MASK); + maskline = (1uL << linepos); + + /* 1] Get core mode : interrupt */ + + /* Check if selected line is enable */ + if ((EXTI->IMR & maskline) != 0x00u) + { + pExtiConfig->Mode = EXTI_MODE_INTERRUPT; + } + else + { + pExtiConfig->Mode = EXTI_MODE_NONE; + } + + /* Get event mode */ + /* Check if selected line is enable */ + if ((EXTI->EMR & maskline) != 0x00u) + { + pExtiConfig->Mode |= EXTI_MODE_EVENT; + } + + /* 2] Get trigger for configurable lines : rising */ + if ((pExtiConfig->Line & EXTI_CONFIG) != 0x00u) + { + /* Check if configuration of selected line is enable */ + if ((EXTI->RTSR & maskline) != 0x00u) + { + pExtiConfig->Trigger = EXTI_TRIGGER_RISING; + } + else + { + pExtiConfig->Trigger = EXTI_TRIGGER_NONE; + } + + /* Get falling configuration */ + /* Check if configuration of selected line is enable */ + if ((EXTI->FTSR & maskline) != 0x00u) + { + pExtiConfig->Trigger |= EXTI_TRIGGER_FALLING; + } + + /* Get Gpio port selection for gpio lines */ + if ((pExtiConfig->Line & EXTI_GPIO) == EXTI_GPIO) + { + assert_param(IS_EXTI_GPIO_PIN(linepos)); + + regval = AFIO->EXTICR[linepos >> 2u]; + pExtiConfig->GPIOSel = ((regval << (AFIO_EXTICR1_EXTI1_Pos * (3uL - (linepos & 0x03u)))) >> 24); + } + else + { + pExtiConfig->GPIOSel = 0x00u; + } + } + else + { + /* No Trigger selected */ + pExtiConfig->Trigger = EXTI_TRIGGER_NONE; + pExtiConfig->GPIOSel = 0x00u; + } + + return HAL_OK; +} + +/** + * @brief Clear whole configuration of a dedicated Exti line. + * @param hexti Exti handle. + * @retval HAL Status. + */ +HAL_StatusTypeDef HAL_EXTI_ClearConfigLine(EXTI_HandleTypeDef* hexti) +{ + uint32_t regval; + uint32_t linepos; + uint32_t maskline; + + /* Check null pointer */ + if (hexti == NULL) + { + return HAL_ERROR; + } + + /* Check the parameter */ + assert_param(IS_EXTI_LINE(hexti->Line)); + + /* compute line mask */ + linepos = (hexti->Line & EXTI_PIN_MASK); + maskline = (1uL << linepos); + + /* 1] Clear interrupt mode */ + EXTI->IMR = (EXTI->IMR & ~maskline); + + /* 2] Clear event mode */ + EXTI->EMR = (EXTI->EMR & ~maskline); + + /* 3] Clear triggers in case of configurable lines */ + if ((hexti->Line & EXTI_CONFIG) != 0x00u) + { + EXTI->RTSR = (EXTI->RTSR & ~maskline); + EXTI->FTSR = (EXTI->FTSR & ~maskline); + + /* Get Gpio port selection for gpio lines */ + if ((hexti->Line & EXTI_GPIO) == EXTI_GPIO) + { + assert_param(IS_EXTI_GPIO_PIN(linepos)); + + regval = AFIO->EXTICR[linepos >> 2u]; + regval &= ~(AFIO_EXTICR1_EXTI0 << (AFIO_EXTICR1_EXTI1_Pos * (linepos & 0x03u))); + AFIO->EXTICR[linepos >> 2u] = regval; + } + } + + return HAL_OK; +} + +/** + * @brief Register callback for a dedicated Exti line. + * @param hexti Exti handle. + * @param CallbackID User callback identifier. + * This parameter can be one of @arg @ref EXTI_CallbackIDTypeDef values. + * @param pPendingCbfn function pointer to be stored as callback. + * @retval HAL Status. + */ +HAL_StatusTypeDef HAL_EXTI_RegisterCallback(EXTI_HandleTypeDef* hexti, EXTI_CallbackIDTypeDef CallbackID, void (*pPendingCbfn)(void)) +{ + HAL_StatusTypeDef status = HAL_OK; + + switch (CallbackID) + { + case HAL_EXTI_COMMON_CB_ID: + hexti->PendingCallback = pPendingCbfn; + break; + + default: + status = HAL_ERROR; + break; + } + + return status; +} + +/** + * @brief Store line number as handle private field. + * @param hexti Exti handle. + * @param ExtiLine Exti line number. + * This parameter can be from 0 to @ref EXTI_LINE_NB. + * @retval HAL Status. + */ +HAL_StatusTypeDef HAL_EXTI_GetHandle(EXTI_HandleTypeDef* hexti, uint32_t ExtiLine) +{ + /* Check the parameters */ + assert_param(IS_EXTI_LINE(ExtiLine)); + + /* Check null pointer */ + if (hexti == NULL) + { + return HAL_ERROR; + } + else + { + /* Store line number as handle private field */ + hexti->Line = ExtiLine; + + return HAL_OK; + } +} + +/** + * @} + */ + +/** @addtogroup EXTI_Exported_Functions_Group2 + * @brief EXTI IO functions. + * +@verbatim + =============================================================================== + ##### IO operation functions ##### + =============================================================================== + +@endverbatim + * @{ + */ + +/** + * @brief Handle EXTI interrupt request. + * @param hexti Exti handle. + * @retval none. + */ +void HAL_EXTI_IRQHandler(EXTI_HandleTypeDef* hexti) +{ + uint32_t regval; + uint32_t maskline; + + /* Compute line mask */ + maskline = (1uL << (hexti->Line & EXTI_PIN_MASK)); + + /* Get pending bit */ + regval = (EXTI->PR & maskline); + + if (regval != 0x00u) + { + /* Clear pending bit */ + EXTI->PR = maskline; + + /* Call callback */ + if (hexti->PendingCallback != NULL) + { + hexti->PendingCallback(); + } + } +} + +/** + * @brief Get interrupt pending bit of a dedicated line. + * @param hexti Exti handle. + * @param Edge Specify which pending edge as to be checked. + * This parameter can be one of the following values: + * @arg @ref EXTI_TRIGGER_RISING_FALLING + * This parameter is kept for compatibility with other series. + * @retval 1 if interrupt is pending else 0. + */ +uint32_t HAL_EXTI_GetPending(EXTI_HandleTypeDef* hexti, uint32_t Edge) +{ + uint32_t regval; + uint32_t maskline; + uint32_t linepos; + + /* Check parameters */ + assert_param(IS_EXTI_LINE(hexti->Line)); + assert_param(IS_EXTI_CONFIG_LINE(hexti->Line)); + assert_param(IS_EXTI_PENDING_EDGE(Edge)); + + /* Compute line mask */ + linepos = (hexti->Line & EXTI_PIN_MASK); + maskline = (1uL << linepos); + + /* return 1 if bit is set else 0 */ + regval = ((EXTI->PR & maskline) >> linepos); + return regval; +} + +/** + * @brief Clear interrupt pending bit of a dedicated line. + * @param hexti Exti handle. + * @param Edge Specify which pending edge as to be clear. + * This parameter can be one of the following values: + * @arg @ref EXTI_TRIGGER_RISING_FALLING + * This parameter is kept for compatibility with other series. + * @retval None. + */ +void HAL_EXTI_ClearPending(EXTI_HandleTypeDef* hexti, uint32_t Edge) +{ + uint32_t maskline; + + /* Check parameters */ + assert_param(IS_EXTI_LINE(hexti->Line)); + assert_param(IS_EXTI_CONFIG_LINE(hexti->Line)); + assert_param(IS_EXTI_PENDING_EDGE(Edge)); + + /* Compute line mask */ + maskline = (1uL << (hexti->Line & EXTI_PIN_MASK)); + + /* Clear Pending bit */ + EXTI->PR = maskline; +} + +/** + * @brief Generate a software interrupt for a dedicated line. + * @param hexti Exti handle. + * @retval None. + */ +void HAL_EXTI_GenerateSWI(EXTI_HandleTypeDef* hexti) +{ + uint32_t maskline; + + /* Check parameters */ + assert_param(IS_EXTI_LINE(hexti->Line)); + assert_param(IS_EXTI_CONFIG_LINE(hexti->Line)); + + /* Compute line mask */ + maskline = (1uL << (hexti->Line & EXTI_PIN_MASK)); + + /* Generate Software interrupt */ + EXTI->SWIER = maskline; +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_EXTI_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_flash.c b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_flash.c new file mode 100644 index 00000000..43ba4e1a --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_flash.c @@ -0,0 +1,992 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_flash.c + * @author MCD Application Team + * @brief FLASH HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the internal FLASH memory: + * + Program operations functions + * + Memory Control functions + * + Peripheral State functions + * + @verbatim + ============================================================================== + ##### FLASH peripheral features ##### + ============================================================================== + [..] The Flash memory interface manages CPU AHB I-Code and D-Code accesses + to the Flash memory. It implements the erase and program Flash memory operations + and the read and write protection mechanisms. + + [..] The Flash memory interface accelerates code execution with a system of instruction + prefetch. + + [..] The FLASH main features are: + (+) Flash memory read operations + (+) Flash memory program/erase operations + (+) Read / write protections + (+) Prefetch on I-Code + (+) Option Bytes programming + + + ##### How to use this driver ##### + ============================================================================== + [..] + This driver provides functions and macros to configure and program the FLASH + memory of all STM32F1xx devices. + + (#) FLASH Memory I/O Programming functions: this group includes all needed + functions to erase and program the main memory: + (++) Lock and Unlock the FLASH interface + (++) Erase function: Erase page, erase all pages + (++) Program functions: half word, word and doubleword + (#) FLASH Option Bytes Programming functions: this group includes all needed + functions to manage the Option Bytes: + (++) Lock and Unlock the Option Bytes + (++) Set/Reset the write protection + (++) Set the Read protection Level + (++) Program the user Option Bytes + (++) Launch the Option Bytes loader + (++) Erase Option Bytes + (++) Program the data Option Bytes + (++) Get the Write protection. + (++) Get the user option bytes. + + (#) Interrupts and flags management functions : this group + includes all needed functions to: + (++) Handle FLASH interrupts + (++) Wait for last FLASH operation according to its status + (++) Get error flag status + + [..] In addition to these function, this driver includes a set of macros allowing + to handle the following operations: + + (+) Set/Get the latency + (+) Enable/Disable the prefetch buffer + (+) Enable/Disable the half cycle access + (+) Enable/Disable the FLASH interrupts + (+) Monitor the FLASH flags status + + @endverbatim + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +#ifdef HAL_FLASH_MODULE_ENABLED + +/** @defgroup FLASH FLASH + * @brief FLASH HAL module driver + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/** @defgroup FLASH_Private_Constants FLASH Private Constants + * @{ + */ +/** + * @} + */ + +/* Private macro ---------------------------- ---------------------------------*/ +/** @defgroup FLASH_Private_Macros FLASH Private Macros + * @{ + */ + +/** + * @} + */ + +/* Private variables ---------------------------------------------------------*/ +/** @defgroup FLASH_Private_Variables FLASH Private Variables + * @{ + */ +/* Variables used for Erase pages under interruption*/ +FLASH_ProcessTypeDef pFlash; +/** + * @} + */ + +/* Private function prototypes -----------------------------------------------*/ +/** @defgroup FLASH_Private_Functions FLASH Private Functions + * @{ + */ +static void FLASH_Program_HalfWord(uint32_t Address, uint16_t Data); +static void FLASH_SetErrorCode(void); +extern void FLASH_PageErase(uint32_t PageAddress); +/** + * @} + */ + +/* Exported functions ---------------------------------------------------------*/ +/** @defgroup FLASH_Exported_Functions FLASH Exported Functions + * @{ + */ + +/** @defgroup FLASH_Exported_Functions_Group1 Programming operation functions + * @brief Programming operation functions + * +@verbatim +@endverbatim + * @{ + */ + +/** + * @brief Program halfword, word or double word at a specified address + * @note The function HAL_FLASH_Unlock() should be called before to unlock the FLASH interface + * The function HAL_FLASH_Lock() should be called after to lock the FLASH interface + * + * @note If an erase and a program operations are requested simultaneously, + * the erase operation is performed before the program one. + * + * @note FLASH should be previously erased before new programmation (only exception to this + * is when 0x0000 is programmed) + * + * @param TypeProgram: Indicate the way to program at a specified address. + * This parameter can be a value of @ref FLASH_Type_Program + * @param Address: Specifies the address to be programmed. + * @param Data: Specifies the data to be programmed + * + * @retval HAL_StatusTypeDef HAL Status + */ +HAL_StatusTypeDef HAL_FLASH_Program(uint32_t TypeProgram, uint32_t Address, uint64_t Data) +{ + HAL_StatusTypeDef status = HAL_ERROR; + uint8_t index = 0; + uint8_t nbiterations = 0; + + /* Process Locked */ + __HAL_LOCK(&pFlash); + + /* Check the parameters */ + assert_param(IS_FLASH_TYPEPROGRAM(TypeProgram)); + assert_param(IS_FLASH_PROGRAM_ADDRESS(Address)); + +#if defined(FLASH_BANK2_END) + + if (Address <= FLASH_BANK1_END) + { +#endif /* FLASH_BANK2_END */ + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation(FLASH_TIMEOUT_VALUE); +#if defined(FLASH_BANK2_END) + } + else + { + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperationBank2(FLASH_TIMEOUT_VALUE); + } + +#endif /* FLASH_BANK2_END */ + + if (status == HAL_OK) + { + if (TypeProgram == FLASH_TYPEPROGRAM_HALFWORD) + { + /* Program halfword (16-bit) at a specified address. */ + nbiterations = 1U; + } + else if (TypeProgram == FLASH_TYPEPROGRAM_WORD) + { + /* Program word (32-bit = 2*16-bit) at a specified address. */ + nbiterations = 2U; + } + else + { + /* Program double word (64-bit = 4*16-bit) at a specified address. */ + nbiterations = 4U; + } + + for (index = 0U; index < nbiterations; index++) + { + FLASH_Program_HalfWord((Address + (2U * index)), (uint16_t)(Data >> (16U * index))); + +#if defined(FLASH_BANK2_END) + + if (Address <= FLASH_BANK1_END) + { +#endif /* FLASH_BANK2_END */ + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation(FLASH_TIMEOUT_VALUE); + + /* If the program operation is completed, disable the PG Bit */ + CLEAR_BIT(FLASH->CR, FLASH_CR_PG); +#if defined(FLASH_BANK2_END) + } + else + { + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperationBank2(FLASH_TIMEOUT_VALUE); + + /* If the program operation is completed, disable the PG Bit */ + CLEAR_BIT(FLASH->CR2, FLASH_CR2_PG); + } + +#endif /* FLASH_BANK2_END */ + + /* In case of error, stop programation procedure */ + if (status != HAL_OK) + { + break; + } + } + } + + /* Process Unlocked */ + __HAL_UNLOCK(&pFlash); + + return status; +} + +/** + * @brief Program halfword, word or double word at a specified address with interrupt enabled. + * @note The function HAL_FLASH_Unlock() should be called before to unlock the FLASH interface + * The function HAL_FLASH_Lock() should be called after to lock the FLASH interface + * + * @note If an erase and a program operations are requested simultaneously, + * the erase operation is performed before the program one. + * + * @param TypeProgram: Indicate the way to program at a specified address. + * This parameter can be a value of @ref FLASH_Type_Program + * @param Address: Specifies the address to be programmed. + * @param Data: Specifies the data to be programmed + * + * @retval HAL_StatusTypeDef HAL Status + */ +HAL_StatusTypeDef HAL_FLASH_Program_IT(uint32_t TypeProgram, uint32_t Address, uint64_t Data) +{ + HAL_StatusTypeDef status = HAL_OK; + + /* Process Locked */ + __HAL_LOCK(&pFlash); + + /* Check the parameters */ + assert_param(IS_FLASH_TYPEPROGRAM(TypeProgram)); + assert_param(IS_FLASH_PROGRAM_ADDRESS(Address)); + +#if defined(FLASH_BANK2_END) + + /* If procedure already ongoing, reject the next one */ + if (pFlash.ProcedureOnGoing != FLASH_PROC_NONE) + { + return HAL_ERROR; + } + + if (Address <= FLASH_BANK1_END) + { + /* Enable End of FLASH Operation and Error source interrupts */ + __HAL_FLASH_ENABLE_IT(FLASH_IT_EOP_BANK1 | FLASH_IT_ERR_BANK1); + + } + else + { + /* Enable End of FLASH Operation and Error source interrupts */ + __HAL_FLASH_ENABLE_IT(FLASH_IT_EOP_BANK2 | FLASH_IT_ERR_BANK2); + } + +#else + /* Enable End of FLASH Operation and Error source interrupts */ + __HAL_FLASH_ENABLE_IT(FLASH_IT_EOP | FLASH_IT_ERR); +#endif /* FLASH_BANK2_END */ + + pFlash.Address = Address; + pFlash.Data = Data; + + if (TypeProgram == FLASH_TYPEPROGRAM_HALFWORD) + { + pFlash.ProcedureOnGoing = FLASH_PROC_PROGRAMHALFWORD; + /* Program halfword (16-bit) at a specified address. */ + pFlash.DataRemaining = 1U; + } + else if (TypeProgram == FLASH_TYPEPROGRAM_WORD) + { + pFlash.ProcedureOnGoing = FLASH_PROC_PROGRAMWORD; + /* Program word (32-bit : 2*16-bit) at a specified address. */ + pFlash.DataRemaining = 2U; + } + else + { + pFlash.ProcedureOnGoing = FLASH_PROC_PROGRAMDOUBLEWORD; + /* Program double word (64-bit : 4*16-bit) at a specified address. */ + pFlash.DataRemaining = 4U; + } + + /* Program halfword (16-bit) at a specified address. */ + FLASH_Program_HalfWord(Address, (uint16_t)Data); + + return status; +} + +/** + * @brief This function handles FLASH interrupt request. + * @retval None + */ +void HAL_FLASH_IRQHandler(void) +{ + uint32_t addresstmp = 0U; + + /* Check FLASH operation error flags */ +#if defined(FLASH_BANK2_END) + + if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR_BANK1) || __HAL_FLASH_GET_FLAG(FLASH_FLAG_PGERR_BANK1) || \ + (__HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR_BANK2) || __HAL_FLASH_GET_FLAG(FLASH_FLAG_PGERR_BANK2))) +#else + if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR) || __HAL_FLASH_GET_FLAG(FLASH_FLAG_PGERR)) +#endif /* FLASH_BANK2_END */ + { + /* Return the faulty address */ + addresstmp = pFlash.Address; + /* Reset address */ + pFlash.Address = 0xFFFFFFFFU; + + /* Save the Error code */ + FLASH_SetErrorCode(); + + /* FLASH error interrupt user callback */ + HAL_FLASH_OperationErrorCallback(addresstmp); + + /* Stop the procedure ongoing */ + pFlash.ProcedureOnGoing = FLASH_PROC_NONE; + } + + /* Check FLASH End of Operation flag */ +#if defined(FLASH_BANK2_END) + + if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_EOP_BANK1)) + { + /* Clear FLASH End of Operation pending bit */ + __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP_BANK1); +#else + + if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_EOP)) + { + /* Clear FLASH End of Operation pending bit */ + __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP); +#endif /* FLASH_BANK2_END */ + + /* Process can continue only if no error detected */ + if (pFlash.ProcedureOnGoing != FLASH_PROC_NONE) + { + if (pFlash.ProcedureOnGoing == FLASH_PROC_PAGEERASE) + { + /* Nb of pages to erased can be decreased */ + pFlash.DataRemaining--; + + /* Check if there are still pages to erase */ + if (pFlash.DataRemaining != 0U) + { + addresstmp = pFlash.Address; + /*Indicate user which sector has been erased */ + HAL_FLASH_EndOfOperationCallback(addresstmp); + + /*Increment sector number*/ + addresstmp = pFlash.Address + FLASH_PAGE_SIZE; + pFlash.Address = addresstmp; + + /* If the erase operation is completed, disable the PER Bit */ + CLEAR_BIT(FLASH->CR, FLASH_CR_PER); + + FLASH_PageErase(addresstmp); + } + else + { + /* No more pages to Erase, user callback can be called. */ + /* Reset Sector and stop Erase pages procedure */ + pFlash.Address = addresstmp = 0xFFFFFFFFU; + pFlash.ProcedureOnGoing = FLASH_PROC_NONE; + /* FLASH EOP interrupt user callback */ + HAL_FLASH_EndOfOperationCallback(addresstmp); + } + } + else if (pFlash.ProcedureOnGoing == FLASH_PROC_MASSERASE) + { + /* Operation is completed, disable the MER Bit */ + CLEAR_BIT(FLASH->CR, FLASH_CR_MER); + +#if defined(FLASH_BANK2_END) + + /* Stop Mass Erase procedure if no pending mass erase on other bank */ + if (HAL_IS_BIT_CLR(FLASH->CR2, FLASH_CR2_MER)) + { +#endif /* FLASH_BANK2_END */ + /* MassErase ended. Return the selected bank */ + /* FLASH EOP interrupt user callback */ + HAL_FLASH_EndOfOperationCallback(0U); + + /* Stop Mass Erase procedure*/ + pFlash.ProcedureOnGoing = FLASH_PROC_NONE; + } + +#if defined(FLASH_BANK2_END) + } + +#endif /* FLASH_BANK2_END */ + else + { + /* Nb of 16-bit data to program can be decreased */ + pFlash.DataRemaining--; + + /* Check if there are still 16-bit data to program */ + if (pFlash.DataRemaining != 0U) + { + /* Increment address to 16-bit */ + pFlash.Address += 2U; + addresstmp = pFlash.Address; + + /* Shift to have next 16-bit data */ + pFlash.Data = (pFlash.Data >> 16U); + + /* Operation is completed, disable the PG Bit */ + CLEAR_BIT(FLASH->CR, FLASH_CR_PG); + + /*Program halfword (16-bit) at a specified address.*/ + FLASH_Program_HalfWord(addresstmp, (uint16_t)pFlash.Data); + } + else + { + /* Program ended. Return the selected address */ + /* FLASH EOP interrupt user callback */ + if (pFlash.ProcedureOnGoing == FLASH_PROC_PROGRAMHALFWORD) + { + HAL_FLASH_EndOfOperationCallback(pFlash.Address); + } + else if (pFlash.ProcedureOnGoing == FLASH_PROC_PROGRAMWORD) + { + HAL_FLASH_EndOfOperationCallback(pFlash.Address - 2U); + } + else + { + HAL_FLASH_EndOfOperationCallback(pFlash.Address - 6U); + } + + /* Reset Address and stop Program procedure */ + pFlash.Address = 0xFFFFFFFFU; + pFlash.ProcedureOnGoing = FLASH_PROC_NONE; + } + } + } + } + +#if defined(FLASH_BANK2_END) + + /* Check FLASH End of Operation flag */ + if (__HAL_FLASH_GET_FLAG( FLASH_FLAG_EOP_BANK2)) + { + /* Clear FLASH End of Operation pending bit */ + __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP_BANK2); + + /* Process can continue only if no error detected */ + if (pFlash.ProcedureOnGoing != FLASH_PROC_NONE) + { + if (pFlash.ProcedureOnGoing == FLASH_PROC_PAGEERASE) + { + /* Nb of pages to erased can be decreased */ + pFlash.DataRemaining--; + + /* Check if there are still pages to erase*/ + if (pFlash.DataRemaining != 0U) + { + /* Indicate user which page address has been erased*/ + HAL_FLASH_EndOfOperationCallback(pFlash.Address); + + /* Increment page address to next page */ + pFlash.Address += FLASH_PAGE_SIZE; + addresstmp = pFlash.Address; + + /* Operation is completed, disable the PER Bit */ + CLEAR_BIT(FLASH->CR2, FLASH_CR2_PER); + + FLASH_PageErase(addresstmp); + } + else + { + /*No more pages to Erase*/ + + /*Reset Address and stop Erase pages procedure*/ + pFlash.Address = 0xFFFFFFFFU; + pFlash.ProcedureOnGoing = FLASH_PROC_NONE; + + /* FLASH EOP interrupt user callback */ + HAL_FLASH_EndOfOperationCallback(pFlash.Address); + } + } + else if (pFlash.ProcedureOnGoing == FLASH_PROC_MASSERASE) + { + /* Operation is completed, disable the MER Bit */ + CLEAR_BIT(FLASH->CR2, FLASH_CR2_MER); + + if (HAL_IS_BIT_CLR(FLASH->CR, FLASH_CR_MER)) + { + /* MassErase ended. Return the selected bank*/ + /* FLASH EOP interrupt user callback */ + HAL_FLASH_EndOfOperationCallback(0U); + + pFlash.ProcedureOnGoing = FLASH_PROC_NONE; + } + } + else + { + /* Nb of 16-bit data to program can be decreased */ + pFlash.DataRemaining--; + + /* Check if there are still 16-bit data to program */ + if (pFlash.DataRemaining != 0U) + { + /* Increment address to 16-bit */ + pFlash.Address += 2U; + addresstmp = pFlash.Address; + + /* Shift to have next 16-bit data */ + pFlash.Data = (pFlash.Data >> 16U); + + /* Operation is completed, disable the PG Bit */ + CLEAR_BIT(FLASH->CR2, FLASH_CR2_PG); + + /*Program halfword (16-bit) at a specified address.*/ + FLASH_Program_HalfWord(addresstmp, (uint16_t)pFlash.Data); + } + else + { + /*Program ended. Return the selected address*/ + /* FLASH EOP interrupt user callback */ + if (pFlash.ProcedureOnGoing == FLASH_PROC_PROGRAMHALFWORD) + { + HAL_FLASH_EndOfOperationCallback(pFlash.Address); + } + else if (pFlash.ProcedureOnGoing == FLASH_PROC_PROGRAMWORD) + { + HAL_FLASH_EndOfOperationCallback(pFlash.Address - 2U); + } + else + { + HAL_FLASH_EndOfOperationCallback(pFlash.Address - 6U); + } + + /* Reset Address and stop Program procedure*/ + pFlash.Address = 0xFFFFFFFFU; + pFlash.ProcedureOnGoing = FLASH_PROC_NONE; + } + } + } + } + +#endif + + if (pFlash.ProcedureOnGoing == FLASH_PROC_NONE) + { +#if defined(FLASH_BANK2_END) + /* Operation is completed, disable the PG, PER and MER Bits for both bank */ + CLEAR_BIT(FLASH->CR, (FLASH_CR_PG | FLASH_CR_PER | FLASH_CR_MER)); + CLEAR_BIT(FLASH->CR2, (FLASH_CR2_PG | FLASH_CR2_PER | FLASH_CR2_MER)); + + /* Disable End of FLASH Operation and Error source interrupts for both banks */ + __HAL_FLASH_DISABLE_IT(FLASH_IT_EOP_BANK1 | FLASH_IT_ERR_BANK1 | FLASH_IT_EOP_BANK2 | FLASH_IT_ERR_BANK2); +#else + /* Operation is completed, disable the PG, PER and MER Bits */ + CLEAR_BIT(FLASH->CR, (FLASH_CR_PG | FLASH_CR_PER | FLASH_CR_MER)); + + /* Disable End of FLASH Operation and Error source interrupts */ + __HAL_FLASH_DISABLE_IT(FLASH_IT_EOP | FLASH_IT_ERR); +#endif /* FLASH_BANK2_END */ + + /* Process Unlocked */ + __HAL_UNLOCK(&pFlash); + } +} + +/** + * @brief FLASH end of operation interrupt callback + * @param ReturnValue: The value saved in this parameter depends on the ongoing procedure + * - Mass Erase: No return value expected + * - Pages Erase: Address of the page which has been erased + * (if 0xFFFFFFFF, it means that all the selected pages have been erased) + * - Program: Address which was selected for data program + * @retval none + */ +__weak void HAL_FLASH_EndOfOperationCallback(uint32_t ReturnValue) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(ReturnValue); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_FLASH_EndOfOperationCallback could be implemented in the user file + */ +} + +/** + * @brief FLASH operation error interrupt callback + * @param ReturnValue: The value saved in this parameter depends on the ongoing procedure + * - Mass Erase: No return value expected + * - Pages Erase: Address of the page which returned an error + * - Program: Address which was selected for data program + * @retval none + */ +__weak void HAL_FLASH_OperationErrorCallback(uint32_t ReturnValue) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(ReturnValue); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_FLASH_OperationErrorCallback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup FLASH_Exported_Functions_Group2 Peripheral Control functions + * @brief management functions + * +@verbatim + =============================================================================== + ##### Peripheral Control functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to control the FLASH + memory operations. + +@endverbatim + * @{ + */ + +/** + * @brief Unlock the FLASH control register access + * @retval HAL Status + */ +HAL_StatusTypeDef HAL_FLASH_Unlock(void) +{ + HAL_StatusTypeDef status = HAL_OK; + + if (READ_BIT(FLASH->CR, FLASH_CR_LOCK) != RESET) + { + /* Authorize the FLASH Registers access */ + WRITE_REG(FLASH->KEYR, FLASH_KEY1); + WRITE_REG(FLASH->KEYR, FLASH_KEY2); + + /* Verify Flash is unlocked */ + if (READ_BIT(FLASH->CR, FLASH_CR_LOCK) != RESET) + { + status = HAL_ERROR; + } + } + +#if defined(FLASH_BANK2_END) + + if (READ_BIT(FLASH->CR2, FLASH_CR2_LOCK) != RESET) + { + /* Authorize the FLASH BANK2 Registers access */ + WRITE_REG(FLASH->KEYR2, FLASH_KEY1); + WRITE_REG(FLASH->KEYR2, FLASH_KEY2); + + /* Verify Flash BANK2 is unlocked */ + if (READ_BIT(FLASH->CR2, FLASH_CR2_LOCK) != RESET) + { + status = HAL_ERROR; + } + } + +#endif /* FLASH_BANK2_END */ + + return status; +} + +/** + * @brief Locks the FLASH control register access + * @retval HAL Status + */ +HAL_StatusTypeDef HAL_FLASH_Lock(void) +{ + /* Set the LOCK Bit to lock the FLASH Registers access */ + SET_BIT(FLASH->CR, FLASH_CR_LOCK); + +#if defined(FLASH_BANK2_END) + /* Set the LOCK Bit to lock the FLASH BANK2 Registers access */ + SET_BIT(FLASH->CR2, FLASH_CR2_LOCK); + +#endif /* FLASH_BANK2_END */ + return HAL_OK; +} + +/** + * @brief Unlock the FLASH Option Control Registers access. + * @retval HAL Status + */ +HAL_StatusTypeDef HAL_FLASH_OB_Unlock(void) +{ + if (HAL_IS_BIT_CLR(FLASH->CR, FLASH_CR_OPTWRE)) + { + /* Authorizes the Option Byte register programming */ + WRITE_REG(FLASH->OPTKEYR, FLASH_OPTKEY1); + WRITE_REG(FLASH->OPTKEYR, FLASH_OPTKEY2); + } + else + { + return HAL_ERROR; + } + + return HAL_OK; +} + +/** + * @brief Lock the FLASH Option Control Registers access. + * @retval HAL Status + */ +HAL_StatusTypeDef HAL_FLASH_OB_Lock(void) +{ + /* Clear the OPTWRE Bit to lock the FLASH Option Byte Registers access */ + CLEAR_BIT(FLASH->CR, FLASH_CR_OPTWRE); + + return HAL_OK; +} + +/** + * @brief Launch the option byte loading. + * @note This function will reset automatically the MCU. + * @retval None + */ +void HAL_FLASH_OB_Launch(void) +{ + /* Initiates a system reset request to launch the option byte loading */ + HAL_NVIC_SystemReset(); +} + +/** + * @} + */ + +/** @defgroup FLASH_Exported_Functions_Group3 Peripheral errors functions + * @brief Peripheral errors functions + * +@verbatim + =============================================================================== + ##### Peripheral Errors functions ##### + =============================================================================== + [..] + This subsection permit to get in run-time errors of the FLASH peripheral. + +@endverbatim + * @{ + */ + +/** + * @brief Get the specific FLASH error flag. + * @retval FLASH_ErrorCode The returned value can be: + * @ref FLASH_Error_Codes + */ +uint32_t HAL_FLASH_GetError(void) +{ + return pFlash.ErrorCode; +} + +/** + * @} + */ + +/** + * @} + */ + +/** @addtogroup FLASH_Private_Functions + * @{ + */ + +/** + * @brief Program a half-word (16-bit) at a specified address. + * @param Address specify the address to be programmed. + * @param Data specify the data to be programmed. + * @retval None + */ +static void FLASH_Program_HalfWord(uint32_t Address, uint16_t Data) +{ + /* Clean the error context */ + pFlash.ErrorCode = HAL_FLASH_ERROR_NONE; + +#if defined(FLASH_BANK2_END) + + if (Address <= FLASH_BANK1_END) + { +#endif /* FLASH_BANK2_END */ + /* Proceed to program the new data */ + SET_BIT(FLASH->CR, FLASH_CR_PG); +#if defined(FLASH_BANK2_END) + } + else + { + /* Proceed to program the new data */ + SET_BIT(FLASH->CR2, FLASH_CR2_PG); + } + +#endif /* FLASH_BANK2_END */ + + /* Write data in the address */ + *(__IO uint16_t*)Address = Data; +} + +/** + * @brief Wait for a FLASH operation to complete. + * @param Timeout maximum flash operation timeout + * @retval HAL Status + */ +HAL_StatusTypeDef FLASH_WaitForLastOperation(uint32_t Timeout) +{ + /* Wait for the FLASH operation to complete by polling on BUSY flag to be reset. + Even if the FLASH operation fails, the BUSY flag will be reset and an error + flag will be set */ + + uint32_t tickstart = HAL_GetTick(); + + while (__HAL_FLASH_GET_FLAG(FLASH_FLAG_BSY)) + { + if (Timeout != HAL_MAX_DELAY) + { + if ((Timeout == 0U) || ((HAL_GetTick() - tickstart) > Timeout)) + { + return HAL_TIMEOUT; + } + } + } + + /* Check FLASH End of Operation flag */ + if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_EOP)) + { + /* Clear FLASH End of Operation pending bit */ + __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP); + } + + if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR) || + __HAL_FLASH_GET_FLAG(FLASH_FLAG_OPTVERR) || + __HAL_FLASH_GET_FLAG(FLASH_FLAG_PGERR)) + { + /*Save the error code*/ + FLASH_SetErrorCode(); + return HAL_ERROR; + } + + /* There is no error flag set */ + return HAL_OK; +} + +#if defined(FLASH_BANK2_END) +/** + * @brief Wait for a FLASH BANK2 operation to complete. + * @param Timeout maximum flash operation timeout + * @retval HAL_StatusTypeDef HAL Status + */ +HAL_StatusTypeDef FLASH_WaitForLastOperationBank2(uint32_t Timeout) +{ + /* Wait for the FLASH BANK2 operation to complete by polling on BUSY flag to be reset. + Even if the FLASH BANK2 operation fails, the BUSY flag will be reset and an error + flag will be set */ + + uint32_t tickstart = HAL_GetTick(); + + while (__HAL_FLASH_GET_FLAG(FLASH_FLAG_BSY_BANK2)) + { + if (Timeout != HAL_MAX_DELAY) + { + if ((Timeout == 0U) || ((HAL_GetTick() - tickstart) > Timeout)) + { + return HAL_TIMEOUT; + } + } + } + + /* Check FLASH End of Operation flag */ + if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_EOP_BANK2)) + { + /* Clear FLASH End of Operation pending bit */ + __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP_BANK2); + } + + if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR_BANK2) || __HAL_FLASH_GET_FLAG(FLASH_FLAG_PGERR_BANK2)) + { + /*Save the error code*/ + FLASH_SetErrorCode(); + return HAL_ERROR; + } + + /* If there is an error flag set */ + return HAL_OK; + +} +#endif /* FLASH_BANK2_END */ + +/** + * @brief Set the specific FLASH error flag. + * @retval None + */ +static void FLASH_SetErrorCode(void) +{ + uint32_t flags = 0U; + +#if defined(FLASH_BANK2_END) + + if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR) || __HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR_BANK2)) +#else + if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR)) +#endif /* FLASH_BANK2_END */ + { + pFlash.ErrorCode |= HAL_FLASH_ERROR_WRP; +#if defined(FLASH_BANK2_END) + flags |= FLASH_FLAG_WRPERR | FLASH_FLAG_WRPERR_BANK2; +#else + flags |= FLASH_FLAG_WRPERR; +#endif /* FLASH_BANK2_END */ + } + +#if defined(FLASH_BANK2_END) + + if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_PGERR) || __HAL_FLASH_GET_FLAG(FLASH_FLAG_PGERR_BANK2)) +#else + if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_PGERR)) +#endif /* FLASH_BANK2_END */ + { + pFlash.ErrorCode |= HAL_FLASH_ERROR_PROG; +#if defined(FLASH_BANK2_END) + flags |= FLASH_FLAG_PGERR | FLASH_FLAG_PGERR_BANK2; +#else + flags |= FLASH_FLAG_PGERR; +#endif /* FLASH_BANK2_END */ + } + + if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_OPTVERR)) + { + pFlash.ErrorCode |= HAL_FLASH_ERROR_OPTV; + __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_OPTVERR); + } + + /* Clear FLASH error pending bits */ + __HAL_FLASH_CLEAR_FLAG(flags); +} +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_FLASH_MODULE_ENABLED */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_flash_ex.c b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_flash_ex.c new file mode 100644 index 00000000..4ad4cfcb --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_flash_ex.c @@ -0,0 +1,1159 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_flash_ex.c + * @author MCD Application Team + * @brief Extended FLASH HAL module driver. + * + * This file provides firmware functions to manage the following + * functionalities of the FLASH peripheral: + * + Extended Initialization/de-initialization functions + * + Extended I/O operation functions + * + Extended Peripheral Control functions + * + @verbatim + ============================================================================== + ##### Flash peripheral extended features ##### + ============================================================================== + + ##### How to use this driver ##### + ============================================================================== + [..] This driver provides functions to configure and program the FLASH memory + of all STM32F1xxx devices. It includes + + (++) Set/Reset the write protection + (++) Program the user Option Bytes + (++) Get the Read protection Level + + @endverbatim + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ +#ifdef HAL_FLASH_MODULE_ENABLED + +/** @addtogroup FLASH + * @{ + */ +/** @addtogroup FLASH_Private_Variables + * @{ + */ +/* Variables used for Erase pages under interruption*/ +extern FLASH_ProcessTypeDef pFlash; +/** + * @} + */ + +/** + * @} + */ + +/** @defgroup FLASHEx FLASHEx + * @brief FLASH HAL Extension module driver + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/** @defgroup FLASHEx_Private_Constants FLASHEx Private Constants + * @{ + */ +#define FLASH_POSITION_IWDGSW_BIT FLASH_OBR_IWDG_SW_Pos +#define FLASH_POSITION_OB_USERDATA0_BIT FLASH_OBR_DATA0_Pos +#define FLASH_POSITION_OB_USERDATA1_BIT FLASH_OBR_DATA1_Pos +/** + * @} + */ + +/* Private macro -------------------------------------------------------------*/ +/** @defgroup FLASHEx_Private_Macros FLASHEx Private Macros + * @{ + */ +/** + * @} + */ + +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/** @defgroup FLASHEx_Private_Functions FLASHEx Private Functions + * @{ + */ +/* Erase operations */ +static void FLASH_MassErase(uint32_t Banks); +void FLASH_PageErase(uint32_t PageAddress); + +/* Option bytes control */ +static HAL_StatusTypeDef FLASH_OB_EnableWRP(uint32_t WriteProtectPage); +static HAL_StatusTypeDef FLASH_OB_DisableWRP(uint32_t WriteProtectPage); +static HAL_StatusTypeDef FLASH_OB_RDP_LevelConfig(uint8_t ReadProtectLevel); +static HAL_StatusTypeDef FLASH_OB_UserConfig(uint8_t UserConfig); +static HAL_StatusTypeDef FLASH_OB_ProgramData(uint32_t Address, uint8_t Data); +static uint32_t FLASH_OB_GetWRP(void); +static uint32_t FLASH_OB_GetRDP(void); +static uint8_t FLASH_OB_GetUser(void); + +/** + * @} + */ + +/* Exported functions ---------------------------------------------------------*/ +/** @defgroup FLASHEx_Exported_Functions FLASHEx Exported Functions + * @{ + */ + +/** @defgroup FLASHEx_Exported_Functions_Group1 FLASHEx Memory Erasing functions + * @brief FLASH Memory Erasing functions + * +@verbatim + ============================================================================== + ##### FLASH Erasing Programming functions ##### + ============================================================================== + + [..] The FLASH Memory Erasing functions, includes the following functions: + (+) @ref HAL_FLASHEx_Erase: return only when erase has been done + (+) @ref HAL_FLASHEx_Erase_IT: end of erase is done when @ref HAL_FLASH_EndOfOperationCallback + is called with parameter 0xFFFFFFFF + + [..] Any operation of erase should follow these steps: + (#) Call the @ref HAL_FLASH_Unlock() function to enable the flash control register and + program memory access. + (#) Call the desired function to erase page. + (#) Call the @ref HAL_FLASH_Lock() to disable the flash program memory access + (recommended to protect the FLASH memory against possible unwanted operation). + +@endverbatim + * @{ + */ + + +/** + * @brief Perform a mass erase or erase the specified FLASH memory pages + * @note To correctly run this function, the @ref HAL_FLASH_Unlock() function + * must be called before. + * Call the @ref HAL_FLASH_Lock() to disable the flash memory access + * (recommended to protect the FLASH memory against possible unwanted operation) + * @param[in] pEraseInit pointer to an FLASH_EraseInitTypeDef structure that + * contains the configuration information for the erasing. + * + * @param[out] PageError pointer to variable that + * contains the configuration information on faulty page in case of error + * (0xFFFFFFFF means that all the pages have been correctly erased) + * + * @retval HAL_StatusTypeDef HAL Status + */ +HAL_StatusTypeDef HAL_FLASHEx_Erase(FLASH_EraseInitTypeDef* pEraseInit, uint32_t* PageError) +{ + HAL_StatusTypeDef status = HAL_ERROR; + uint32_t address = 0U; + + /* Process Locked */ + __HAL_LOCK(&pFlash); + + /* Check the parameters */ + assert_param(IS_FLASH_TYPEERASE(pEraseInit->TypeErase)); + + if (pEraseInit->TypeErase == FLASH_TYPEERASE_MASSERASE) + { +#if defined(FLASH_BANK2_END) + + if (pEraseInit->Banks == FLASH_BANK_BOTH) + { + /* Mass Erase requested for Bank1 and Bank2 */ + /* Wait for last operation to be completed */ + if ((FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE) == HAL_OK) && \ + (FLASH_WaitForLastOperationBank2((uint32_t)FLASH_TIMEOUT_VALUE) == HAL_OK)) + { + /*Mass erase to be done*/ + FLASH_MassErase(FLASH_BANK_BOTH); + + /* Wait for last operation to be completed */ + if ((FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE) == HAL_OK) && \ + (FLASH_WaitForLastOperationBank2((uint32_t)FLASH_TIMEOUT_VALUE) == HAL_OK)) + { + status = HAL_OK; + } + + /* If the erase operation is completed, disable the MER Bit */ + CLEAR_BIT(FLASH->CR, FLASH_CR_MER); + CLEAR_BIT(FLASH->CR2, FLASH_CR2_MER); + } + } + else if (pEraseInit->Banks == FLASH_BANK_2) + { + /* Mass Erase requested for Bank2 */ + /* Wait for last operation to be completed */ + if (FLASH_WaitForLastOperationBank2((uint32_t)FLASH_TIMEOUT_VALUE) == HAL_OK) + { + /*Mass erase to be done*/ + FLASH_MassErase(FLASH_BANK_2); + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperationBank2((uint32_t)FLASH_TIMEOUT_VALUE); + + /* If the erase operation is completed, disable the MER Bit */ + CLEAR_BIT(FLASH->CR2, FLASH_CR2_MER); + } + } + else +#endif /* FLASH_BANK2_END */ + { + /* Mass Erase requested for Bank1 */ + /* Wait for last operation to be completed */ + if (FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE) == HAL_OK) + { + /*Mass erase to be done*/ + FLASH_MassErase(FLASH_BANK_1); + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + + /* If the erase operation is completed, disable the MER Bit */ + CLEAR_BIT(FLASH->CR, FLASH_CR_MER); + } + } + } + else + { + /* Page Erase is requested */ + /* Check the parameters */ + assert_param(IS_FLASH_PROGRAM_ADDRESS(pEraseInit->PageAddress)); + assert_param(IS_FLASH_NB_PAGES(pEraseInit->PageAddress, pEraseInit->NbPages)); + +#if defined(FLASH_BANK2_END) + + /* Page Erase requested on address located on bank2 */ + if (pEraseInit->PageAddress > FLASH_BANK1_END) + { + /* Wait for last operation to be completed */ + if (FLASH_WaitForLastOperationBank2((uint32_t)FLASH_TIMEOUT_VALUE) == HAL_OK) + { + /*Initialization of PageError variable*/ + *PageError = 0xFFFFFFFFU; + + /* Erase by page by page to be done*/ + for (address = pEraseInit->PageAddress; + address < (pEraseInit->PageAddress + (pEraseInit->NbPages)*FLASH_PAGE_SIZE); + address += FLASH_PAGE_SIZE) + { + FLASH_PageErase(address); + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperationBank2((uint32_t)FLASH_TIMEOUT_VALUE); + + /* If the erase operation is completed, disable the PER Bit */ + CLEAR_BIT(FLASH->CR2, FLASH_CR2_PER); + + if (status != HAL_OK) + { + /* In case of error, stop erase procedure and return the faulty address */ + *PageError = address; + break; + } + } + } + } + else +#endif /* FLASH_BANK2_END */ + { + /* Page Erase requested on address located on bank1 */ + /* Wait for last operation to be completed */ + if (FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE) == HAL_OK) + { + /*Initialization of PageError variable*/ + *PageError = 0xFFFFFFFFU; + + /* Erase page by page to be done*/ + for (address = pEraseInit->PageAddress; + address < ((pEraseInit->NbPages * FLASH_PAGE_SIZE) + pEraseInit->PageAddress); + address += FLASH_PAGE_SIZE) + { + FLASH_PageErase(address); + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + + /* If the erase operation is completed, disable the PER Bit */ + CLEAR_BIT(FLASH->CR, FLASH_CR_PER); + + if (status != HAL_OK) + { + /* In case of error, stop erase procedure and return the faulty address */ + *PageError = address; + break; + } + } + } + } + } + + /* Process Unlocked */ + __HAL_UNLOCK(&pFlash); + + return status; +} + +/** + * @brief Perform a mass erase or erase the specified FLASH memory pages with interrupt enabled + * @note To correctly run this function, the @ref HAL_FLASH_Unlock() function + * must be called before. + * Call the @ref HAL_FLASH_Lock() to disable the flash memory access + * (recommended to protect the FLASH memory against possible unwanted operation) + * @param pEraseInit pointer to an FLASH_EraseInitTypeDef structure that + * contains the configuration information for the erasing. + * + * @retval HAL_StatusTypeDef HAL Status + */ +HAL_StatusTypeDef HAL_FLASHEx_Erase_IT(FLASH_EraseInitTypeDef* pEraseInit) +{ + HAL_StatusTypeDef status = HAL_OK; + + /* Process Locked */ + __HAL_LOCK(&pFlash); + + /* If procedure already ongoing, reject the next one */ + if (pFlash.ProcedureOnGoing != FLASH_PROC_NONE) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_FLASH_TYPEERASE(pEraseInit->TypeErase)); + + /* Enable End of FLASH Operation and Error source interrupts */ + __HAL_FLASH_ENABLE_IT(FLASH_IT_EOP | FLASH_IT_ERR); + +#if defined(FLASH_BANK2_END) + /* Enable End of FLASH Operation and Error source interrupts */ + __HAL_FLASH_ENABLE_IT(FLASH_IT_EOP_BANK2 | FLASH_IT_ERR_BANK2); + +#endif + + if (pEraseInit->TypeErase == FLASH_TYPEERASE_MASSERASE) + { + /*Mass erase to be done*/ + pFlash.ProcedureOnGoing = FLASH_PROC_MASSERASE; + FLASH_MassErase(pEraseInit->Banks); + } + else + { + /* Erase by page to be done*/ + + /* Check the parameters */ + assert_param(IS_FLASH_PROGRAM_ADDRESS(pEraseInit->PageAddress)); + assert_param(IS_FLASH_NB_PAGES(pEraseInit->PageAddress, pEraseInit->NbPages)); + + pFlash.ProcedureOnGoing = FLASH_PROC_PAGEERASE; + pFlash.DataRemaining = pEraseInit->NbPages; + pFlash.Address = pEraseInit->PageAddress; + + /*Erase 1st page and wait for IT*/ + FLASH_PageErase(pEraseInit->PageAddress); + } + + return status; +} + +/** + * @} + */ + +/** @defgroup FLASHEx_Exported_Functions_Group2 Option Bytes Programming functions + * @brief Option Bytes Programming functions + * +@verbatim + ============================================================================== + ##### Option Bytes Programming functions ##### + ============================================================================== + [..] + This subsection provides a set of functions allowing to control the FLASH + option bytes operations. + +@endverbatim + * @{ + */ + +/** + * @brief Erases the FLASH option bytes. + * @note This functions erases all option bytes except the Read protection (RDP). + * The function @ref HAL_FLASH_Unlock() should be called before to unlock the FLASH interface + * The function @ref HAL_FLASH_OB_Unlock() should be called before to unlock the options bytes + * The function @ref HAL_FLASH_OB_Launch() should be called after to force the reload of the options bytes + * (system reset will occur) + * @retval HAL status + */ + +HAL_StatusTypeDef HAL_FLASHEx_OBErase(void) +{ + uint8_t rdptmp = OB_RDP_LEVEL_0; + HAL_StatusTypeDef status = HAL_ERROR; + + /* Get the actual read protection Option Byte value */ + rdptmp = FLASH_OB_GetRDP(); + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + + if (status == HAL_OK) + { + /* Clean the error context */ + pFlash.ErrorCode = HAL_FLASH_ERROR_NONE; + + /* If the previous operation is completed, proceed to erase the option bytes */ + SET_BIT(FLASH->CR, FLASH_CR_OPTER); + SET_BIT(FLASH->CR, FLASH_CR_STRT); + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + + /* If the erase operation is completed, disable the OPTER Bit */ + CLEAR_BIT(FLASH->CR, FLASH_CR_OPTER); + + if (status == HAL_OK) + { + /* Restore the last read protection Option Byte value */ + status = FLASH_OB_RDP_LevelConfig(rdptmp); + } + } + + /* Return the erase status */ + return status; +} + +/** + * @brief Program option bytes + * @note The function @ref HAL_FLASH_Unlock() should be called before to unlock the FLASH interface + * The function @ref HAL_FLASH_OB_Unlock() should be called before to unlock the options bytes + * The function @ref HAL_FLASH_OB_Launch() should be called after to force the reload of the options bytes + * (system reset will occur) + * + * @param pOBInit pointer to an FLASH_OBInitStruct structure that + * contains the configuration information for the programming. + * + * @retval HAL_StatusTypeDef HAL Status + */ +HAL_StatusTypeDef HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef* pOBInit) +{ + HAL_StatusTypeDef status = HAL_ERROR; + + /* Process Locked */ + __HAL_LOCK(&pFlash); + + /* Check the parameters */ + assert_param(IS_OPTIONBYTE(pOBInit->OptionType)); + + /* Write protection configuration */ + if ((pOBInit->OptionType & OPTIONBYTE_WRP) == OPTIONBYTE_WRP) + { + assert_param(IS_WRPSTATE(pOBInit->WRPState)); + + if (pOBInit->WRPState == OB_WRPSTATE_ENABLE) + { + /* Enable of Write protection on the selected page */ + status = FLASH_OB_EnableWRP(pOBInit->WRPPage); + } + else + { + /* Disable of Write protection on the selected page */ + status = FLASH_OB_DisableWRP(pOBInit->WRPPage); + } + + if (status != HAL_OK) + { + /* Process Unlocked */ + __HAL_UNLOCK(&pFlash); + return status; + } + } + + /* Read protection configuration */ + if ((pOBInit->OptionType & OPTIONBYTE_RDP) == OPTIONBYTE_RDP) + { + status = FLASH_OB_RDP_LevelConfig(pOBInit->RDPLevel); + + if (status != HAL_OK) + { + /* Process Unlocked */ + __HAL_UNLOCK(&pFlash); + return status; + } + } + + /* USER configuration */ + if ((pOBInit->OptionType & OPTIONBYTE_USER) == OPTIONBYTE_USER) + { + status = FLASH_OB_UserConfig(pOBInit->USERConfig); + + if (status != HAL_OK) + { + /* Process Unlocked */ + __HAL_UNLOCK(&pFlash); + return status; + } + } + + /* DATA configuration*/ + if ((pOBInit->OptionType & OPTIONBYTE_DATA) == OPTIONBYTE_DATA) + { + status = FLASH_OB_ProgramData(pOBInit->DATAAddress, pOBInit->DATAData); + + if (status != HAL_OK) + { + /* Process Unlocked */ + __HAL_UNLOCK(&pFlash); + return status; + } + } + + /* Process Unlocked */ + __HAL_UNLOCK(&pFlash); + + return status; +} + +/** + * @brief Get the Option byte configuration + * @param pOBInit pointer to an FLASH_OBInitStruct structure that + * contains the configuration information for the programming. + * + * @retval None + */ +void HAL_FLASHEx_OBGetConfig(FLASH_OBProgramInitTypeDef* pOBInit) +{ + pOBInit->OptionType = OPTIONBYTE_WRP | OPTIONBYTE_RDP | OPTIONBYTE_USER; + + /*Get WRP*/ + pOBInit->WRPPage = FLASH_OB_GetWRP(); + + /*Get RDP Level*/ + pOBInit->RDPLevel = FLASH_OB_GetRDP(); + + /*Get USER*/ + pOBInit->USERConfig = FLASH_OB_GetUser(); +} + +/** + * @brief Get the Option byte user data + * @param DATAAdress Address of the option byte DATA + * This parameter can be one of the following values: + * @arg @ref OB_DATA_ADDRESS_DATA0 + * @arg @ref OB_DATA_ADDRESS_DATA1 + * @retval Value programmed in USER data + */ +uint32_t HAL_FLASHEx_OBGetUserData(uint32_t DATAAdress) +{ + uint32_t value = 0; + + if (DATAAdress == OB_DATA_ADDRESS_DATA0) + { + /* Get value programmed in OB USER Data0 */ + value = READ_BIT(FLASH->OBR, FLASH_OBR_DATA0) >> FLASH_POSITION_OB_USERDATA0_BIT; + } + else + { + /* Get value programmed in OB USER Data1 */ + value = READ_BIT(FLASH->OBR, FLASH_OBR_DATA1) >> FLASH_POSITION_OB_USERDATA1_BIT; + } + + return value; +} + +/** + * @} + */ + +/** + * @} + */ + +/** @addtogroup FLASHEx_Private_Functions + * @{ + */ + +/** + * @brief Full erase of FLASH memory Bank + * @param Banks Banks to be erased + * This parameter can be one of the following values: + * @arg @ref FLASH_BANK_1 Bank1 to be erased + @if STM32F101xG + * @arg @ref FLASH_BANK_2 Bank2 to be erased + * @arg @ref FLASH_BANK_BOTH Bank1 and Bank2 to be erased + @endif + @if STM32F103xG + * @arg @ref FLASH_BANK_2 Bank2 to be erased + * @arg @ref FLASH_BANK_BOTH Bank1 and Bank2 to be erased + @endif + * + * @retval None + */ +static void FLASH_MassErase(uint32_t Banks) +{ + /* Check the parameters */ + assert_param(IS_FLASH_BANK(Banks)); + + /* Clean the error context */ + pFlash.ErrorCode = HAL_FLASH_ERROR_NONE; + +#if defined(FLASH_BANK2_END) + + if (Banks == FLASH_BANK_BOTH) + { + /* bank1 & bank2 will be erased*/ + SET_BIT(FLASH->CR, FLASH_CR_MER); + SET_BIT(FLASH->CR2, FLASH_CR2_MER); + SET_BIT(FLASH->CR, FLASH_CR_STRT); + SET_BIT(FLASH->CR2, FLASH_CR2_STRT); + } + else if (Banks == FLASH_BANK_2) + { + /*Only bank2 will be erased*/ + SET_BIT(FLASH->CR2, FLASH_CR2_MER); + SET_BIT(FLASH->CR2, FLASH_CR2_STRT); + } + else + { +#endif /* FLASH_BANK2_END */ +#if !defined(FLASH_BANK2_END) + /* Prevent unused argument(s) compilation warning */ + UNUSED(Banks); +#endif /* FLASH_BANK2_END */ + /* Only bank1 will be erased*/ + SET_BIT(FLASH->CR, FLASH_CR_MER); + SET_BIT(FLASH->CR, FLASH_CR_STRT); +#if defined(FLASH_BANK2_END) + } + +#endif /* FLASH_BANK2_END */ +} + +/** + * @brief Enable the write protection of the desired pages + * @note An option byte erase is done automatically in this function. + * @note When the memory read protection level is selected (RDP level = 1), + * it is not possible to program or erase the flash page i if + * debug features are connected or boot code is executed in RAM, even if nWRPi = 1 + * + * @param WriteProtectPage specifies the page(s) to be write protected. + * The value of this parameter depend on device used within the same series + * @retval HAL status + */ +static HAL_StatusTypeDef FLASH_OB_EnableWRP(uint32_t WriteProtectPage) +{ + HAL_StatusTypeDef status = HAL_OK; + uint16_t WRP0_Data = 0xFFFF; +#if defined(FLASH_WRP1_WRP1) + uint16_t WRP1_Data = 0xFFFF; +#endif /* FLASH_WRP1_WRP1 */ +#if defined(FLASH_WRP2_WRP2) + uint16_t WRP2_Data = 0xFFFF; +#endif /* FLASH_WRP2_WRP2 */ +#if defined(FLASH_WRP3_WRP3) + uint16_t WRP3_Data = 0xFFFF; +#endif /* FLASH_WRP3_WRP3 */ + + /* Check the parameters */ + assert_param(IS_OB_WRP(WriteProtectPage)); + + /* Get current write protected pages and the new pages to be protected ******/ + WriteProtectPage = (uint32_t)(~((~FLASH_OB_GetWRP()) | WriteProtectPage)); + +#if defined(OB_WRP_PAGES0TO15MASK) + WRP0_Data = (uint16_t)(WriteProtectPage & OB_WRP_PAGES0TO15MASK); +#elif defined(OB_WRP_PAGES0TO31MASK) + WRP0_Data = (uint16_t)(WriteProtectPage & OB_WRP_PAGES0TO31MASK); +#endif /* OB_WRP_PAGES0TO31MASK */ + +#if defined(OB_WRP_PAGES16TO31MASK) + WRP1_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES16TO31MASK) >> 8U); +#elif defined(OB_WRP_PAGES32TO63MASK) + WRP1_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES32TO63MASK) >> 8U); +#endif /* OB_WRP_PAGES32TO63MASK */ + +#if defined(OB_WRP_PAGES64TO95MASK) + WRP2_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES64TO95MASK) >> 16U); +#endif /* OB_WRP_PAGES64TO95MASK */ +#if defined(OB_WRP_PAGES32TO47MASK) + WRP2_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES32TO47MASK) >> 16U); +#endif /* OB_WRP_PAGES32TO47MASK */ + +#if defined(OB_WRP_PAGES96TO127MASK) + WRP3_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES96TO127MASK) >> 24U); +#elif defined(OB_WRP_PAGES48TO255MASK) + WRP3_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES48TO255MASK) >> 24U); +#elif defined(OB_WRP_PAGES48TO511MASK) + WRP3_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES48TO511MASK) >> 24U); +#elif defined(OB_WRP_PAGES48TO127MASK) + WRP3_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES48TO127MASK) >> 24U); +#endif /* OB_WRP_PAGES96TO127MASK */ + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + + if (status == HAL_OK) + { + /* Clean the error context */ + pFlash.ErrorCode = HAL_FLASH_ERROR_NONE; + + /* To be able to write again option byte, need to perform a option byte erase */ + status = HAL_FLASHEx_OBErase(); + + if (status == HAL_OK) + { + /* Enable write protection */ + SET_BIT(FLASH->CR, FLASH_CR_OPTPG); + +#if defined(FLASH_WRP0_WRP0) + + if (WRP0_Data != 0xFFU) + { + OB->WRP0 &= WRP0_Data; + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + } + +#endif /* FLASH_WRP0_WRP0 */ + +#if defined(FLASH_WRP1_WRP1) + + if ((status == HAL_OK) && (WRP1_Data != 0xFFU)) + { + OB->WRP1 &= WRP1_Data; + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + } + +#endif /* FLASH_WRP1_WRP1 */ + +#if defined(FLASH_WRP2_WRP2) + + if ((status == HAL_OK) && (WRP2_Data != 0xFFU)) + { + OB->WRP2 &= WRP2_Data; + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + } + +#endif /* FLASH_WRP2_WRP2 */ + +#if defined(FLASH_WRP3_WRP3) + + if ((status == HAL_OK) && (WRP3_Data != 0xFFU)) + { + OB->WRP3 &= WRP3_Data; + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + } + +#endif /* FLASH_WRP3_WRP3 */ + + /* if the program operation is completed, disable the OPTPG Bit */ + CLEAR_BIT(FLASH->CR, FLASH_CR_OPTPG); + } + } + + return status; +} + +/** + * @brief Disable the write protection of the desired pages + * @note An option byte erase is done automatically in this function. + * @note When the memory read protection level is selected (RDP level = 1), + * it is not possible to program or erase the flash page i if + * debug features are connected or boot code is executed in RAM, even if nWRPi = 1 + * + * @param WriteProtectPage specifies the page(s) to be write unprotected. + * The value of this parameter depend on device used within the same series + * @retval HAL status + */ +static HAL_StatusTypeDef FLASH_OB_DisableWRP(uint32_t WriteProtectPage) +{ + HAL_StatusTypeDef status = HAL_OK; + uint16_t WRP0_Data = 0xFFFF; +#if defined(FLASH_WRP1_WRP1) + uint16_t WRP1_Data = 0xFFFF; +#endif /* FLASH_WRP1_WRP1 */ +#if defined(FLASH_WRP2_WRP2) + uint16_t WRP2_Data = 0xFFFF; +#endif /* FLASH_WRP2_WRP2 */ +#if defined(FLASH_WRP3_WRP3) + uint16_t WRP3_Data = 0xFFFF; +#endif /* FLASH_WRP3_WRP3 */ + + /* Check the parameters */ + assert_param(IS_OB_WRP(WriteProtectPage)); + + /* Get current write protected pages and the new pages to be unprotected ******/ + WriteProtectPage = (FLASH_OB_GetWRP() | WriteProtectPage); + +#if defined(OB_WRP_PAGES0TO15MASK) + WRP0_Data = (uint16_t)(WriteProtectPage & OB_WRP_PAGES0TO15MASK); +#elif defined(OB_WRP_PAGES0TO31MASK) + WRP0_Data = (uint16_t)(WriteProtectPage & OB_WRP_PAGES0TO31MASK); +#endif /* OB_WRP_PAGES0TO31MASK */ + +#if defined(OB_WRP_PAGES16TO31MASK) + WRP1_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES16TO31MASK) >> 8U); +#elif defined(OB_WRP_PAGES32TO63MASK) + WRP1_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES32TO63MASK) >> 8U); +#endif /* OB_WRP_PAGES32TO63MASK */ + +#if defined(OB_WRP_PAGES64TO95MASK) + WRP2_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES64TO95MASK) >> 16U); +#endif /* OB_WRP_PAGES64TO95MASK */ +#if defined(OB_WRP_PAGES32TO47MASK) + WRP2_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES32TO47MASK) >> 16U); +#endif /* OB_WRP_PAGES32TO47MASK */ + +#if defined(OB_WRP_PAGES96TO127MASK) + WRP3_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES96TO127MASK) >> 24U); +#elif defined(OB_WRP_PAGES48TO255MASK) + WRP3_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES48TO255MASK) >> 24U); +#elif defined(OB_WRP_PAGES48TO511MASK) + WRP3_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES48TO511MASK) >> 24U); +#elif defined(OB_WRP_PAGES48TO127MASK) + WRP3_Data = (uint16_t)((WriteProtectPage & OB_WRP_PAGES48TO127MASK) >> 24U); +#endif /* OB_WRP_PAGES96TO127MASK */ + + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + + if (status == HAL_OK) + { + /* Clean the error context */ + pFlash.ErrorCode = HAL_FLASH_ERROR_NONE; + + /* To be able to write again option byte, need to perform a option byte erase */ + status = HAL_FLASHEx_OBErase(); + + if (status == HAL_OK) + { + SET_BIT(FLASH->CR, FLASH_CR_OPTPG); + +#if defined(FLASH_WRP0_WRP0) + + if (WRP0_Data != 0xFFU) + { + OB->WRP0 |= WRP0_Data; + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + } + +#endif /* FLASH_WRP0_WRP0 */ + +#if defined(FLASH_WRP1_WRP1) + + if ((status == HAL_OK) && (WRP1_Data != 0xFFU)) + { + OB->WRP1 |= WRP1_Data; + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + } + +#endif /* FLASH_WRP1_WRP1 */ + +#if defined(FLASH_WRP2_WRP2) + + if ((status == HAL_OK) && (WRP2_Data != 0xFFU)) + { + OB->WRP2 |= WRP2_Data; + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + } + +#endif /* FLASH_WRP2_WRP2 */ + +#if defined(FLASH_WRP3_WRP3) + + if ((status == HAL_OK) && (WRP3_Data != 0xFFU)) + { + OB->WRP3 |= WRP3_Data; + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + } + +#endif /* FLASH_WRP3_WRP3 */ + + /* if the program operation is completed, disable the OPTPG Bit */ + CLEAR_BIT(FLASH->CR, FLASH_CR_OPTPG); + } + } + + return status; +} + +/** + * @brief Set the read protection level. + * @param ReadProtectLevel specifies the read protection level. + * This parameter can be one of the following values: + * @arg @ref OB_RDP_LEVEL_0 No protection + * @arg @ref OB_RDP_LEVEL_1 Read protection of the memory + * @retval HAL status + */ +static HAL_StatusTypeDef FLASH_OB_RDP_LevelConfig(uint8_t ReadProtectLevel) +{ + HAL_StatusTypeDef status = HAL_OK; + + /* Check the parameters */ + assert_param(IS_OB_RDP_LEVEL(ReadProtectLevel)); + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + + if (status == HAL_OK) + { + /* Clean the error context */ + pFlash.ErrorCode = HAL_FLASH_ERROR_NONE; + + /* If the previous operation is completed, proceed to erase the option bytes */ + SET_BIT(FLASH->CR, FLASH_CR_OPTER); + SET_BIT(FLASH->CR, FLASH_CR_STRT); + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + + /* If the erase operation is completed, disable the OPTER Bit */ + CLEAR_BIT(FLASH->CR, FLASH_CR_OPTER); + + if (status == HAL_OK) + { + /* Enable the Option Bytes Programming operation */ + SET_BIT(FLASH->CR, FLASH_CR_OPTPG); + + WRITE_REG(OB->RDP, ReadProtectLevel); + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + + /* if the program operation is completed, disable the OPTPG Bit */ + CLEAR_BIT(FLASH->CR, FLASH_CR_OPTPG); + } + } + + return status; +} + +/** + * @brief Program the FLASH User Option Byte. + * @note Programming of the OB should be performed only after an erase (otherwise PGERR occurs) + * @param UserConfig The FLASH User Option Bytes values FLASH_OBR_IWDG_SW(Bit2), + * FLASH_OBR_nRST_STOP(Bit3),FLASH_OBR_nRST_STDBY(Bit4). + * And BFBF2(Bit5) for STM32F101xG and STM32F103xG . + * @retval HAL status + */ +static HAL_StatusTypeDef FLASH_OB_UserConfig(uint8_t UserConfig) +{ + HAL_StatusTypeDef status = HAL_OK; + + /* Check the parameters */ + assert_param(IS_OB_IWDG_SOURCE((UserConfig & OB_IWDG_SW))); + assert_param(IS_OB_STOP_SOURCE((UserConfig & OB_STOP_NO_RST))); + assert_param(IS_OB_STDBY_SOURCE((UserConfig & OB_STDBY_NO_RST))); +#if defined(FLASH_BANK2_END) + assert_param(IS_OB_BOOT1((UserConfig & OB_BOOT1_SET))); +#endif /* FLASH_BANK2_END */ + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + + if (status == HAL_OK) + { + /* Clean the error context */ + pFlash.ErrorCode = HAL_FLASH_ERROR_NONE; + + /* Enable the Option Bytes Programming operation */ + SET_BIT(FLASH->CR, FLASH_CR_OPTPG); + +#if defined(FLASH_BANK2_END) + OB->USER = (UserConfig | 0xF0U); +#else + OB->USER = (UserConfig | 0x88U); +#endif /* FLASH_BANK2_END */ + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + + /* if the program operation is completed, disable the OPTPG Bit */ + CLEAR_BIT(FLASH->CR, FLASH_CR_OPTPG); + } + + return status; +} + +/** + * @brief Programs a half word at a specified Option Byte Data address. + * @note The function @ref HAL_FLASH_Unlock() should be called before to unlock the FLASH interface + * The function @ref HAL_FLASH_OB_Unlock() should be called before to unlock the options bytes + * The function @ref HAL_FLASH_OB_Launch() should be called after to force the reload of the options bytes + * (system reset will occur) + * Programming of the OB should be performed only after an erase (otherwise PGERR occurs) + * @param Address specifies the address to be programmed. + * This parameter can be 0x1FFFF804 or 0x1FFFF806. + * @param Data specifies the data to be programmed. + * @retval HAL status + */ +static HAL_StatusTypeDef FLASH_OB_ProgramData(uint32_t Address, uint8_t Data) +{ + HAL_StatusTypeDef status = HAL_ERROR; + + /* Check the parameters */ + assert_param(IS_OB_DATA_ADDRESS(Address)); + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + + if (status == HAL_OK) + { + /* Clean the error context */ + pFlash.ErrorCode = HAL_FLASH_ERROR_NONE; + + /* Enables the Option Bytes Programming operation */ + SET_BIT(FLASH->CR, FLASH_CR_OPTPG); + *(__IO uint16_t*)Address = Data; + + /* Wait for last operation to be completed */ + status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); + + /* If the program operation is completed, disable the OPTPG Bit */ + CLEAR_BIT(FLASH->CR, FLASH_CR_OPTPG); + } + + /* Return the Option Byte Data Program Status */ + return status; +} + +/** + * @brief Return the FLASH Write Protection Option Bytes value. + * @retval The FLASH Write Protection Option Bytes value + */ +static uint32_t FLASH_OB_GetWRP(void) +{ + /* Return the FLASH write protection Register value */ + return (uint32_t)(READ_REG(FLASH->WRPR)); +} + +/** + * @brief Returns the FLASH Read Protection level. + * @retval FLASH RDP level + * This parameter can be one of the following values: + * @arg @ref OB_RDP_LEVEL_0 No protection + * @arg @ref OB_RDP_LEVEL_1 Read protection of the memory + */ +static uint32_t FLASH_OB_GetRDP(void) +{ + uint32_t readstatus = OB_RDP_LEVEL_0; + uint32_t tmp_reg = 0U; + + /* Read RDP level bits */ + tmp_reg = READ_BIT(FLASH->OBR, FLASH_OBR_RDPRT); + + if (tmp_reg == FLASH_OBR_RDPRT) + { + readstatus = OB_RDP_LEVEL_1; + } + else + { + readstatus = OB_RDP_LEVEL_0; + } + + return readstatus; +} + +/** + * @brief Return the FLASH User Option Byte value. + * @retval The FLASH User Option Bytes values: FLASH_OBR_IWDG_SW(Bit2), + * FLASH_OBR_nRST_STOP(Bit3),FLASH_OBR_nRST_STDBY(Bit4). + * And FLASH_OBR_BFB2(Bit5) for STM32F101xG and STM32F103xG . + */ +static uint8_t FLASH_OB_GetUser(void) +{ + /* Return the User Option Byte */ + return (uint8_t)((READ_REG(FLASH->OBR) & FLASH_OBR_USER) >> FLASH_POSITION_IWDGSW_BIT); +} + +/** + * @} + */ + +/** + * @} + */ + +/** @addtogroup FLASH + * @{ + */ + +/** @addtogroup FLASH_Private_Functions + * @{ + */ + +/** + * @brief Erase the specified FLASH memory page + * @param PageAddress FLASH page to erase + * The value of this parameter depend on device used within the same series + * + * @retval None + */ +void FLASH_PageErase(uint32_t PageAddress) +{ + /* Clean the error context */ + pFlash.ErrorCode = HAL_FLASH_ERROR_NONE; + +#if defined(FLASH_BANK2_END) + + if (PageAddress > FLASH_BANK1_END) + { + /* Proceed to erase the page */ + SET_BIT(FLASH->CR2, FLASH_CR2_PER); + WRITE_REG(FLASH->AR2, PageAddress); + SET_BIT(FLASH->CR2, FLASH_CR2_STRT); + } + else + { +#endif /* FLASH_BANK2_END */ + /* Proceed to erase the page */ + SET_BIT(FLASH->CR, FLASH_CR_PER); + WRITE_REG(FLASH->AR, PageAddress); + SET_BIT(FLASH->CR, FLASH_CR_STRT); +#if defined(FLASH_BANK2_END) + } + +#endif /* FLASH_BANK2_END */ +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_FLASH_MODULE_ENABLED */ +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_gpio.c b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_gpio.c new file mode 100644 index 00000000..6514ff0f --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_gpio.c @@ -0,0 +1,593 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_gpio.c + * @author MCD Application Team + * @brief GPIO HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the General Purpose Input/Output (GPIO) peripheral: + * + Initialization and de-initialization functions + * + IO operation functions + * + @verbatim + ============================================================================== + ##### GPIO Peripheral features ##### + ============================================================================== + [..] + Subject to the specific hardware characteristics of each I/O port listed in the datasheet, each + port bit of the General Purpose IO (GPIO) Ports, can be individually configured by software + in several modes: + (+) Input mode + (+) Analog mode + (+) Output mode + (+) Alternate function mode + (+) External interrupt/event lines + + [..] + During and just after reset, the alternate functions and external interrupt + lines are not active and the I/O ports are configured in input floating mode. + + [..] + All GPIO pins have weak internal pull-up and pull-down resistors, which can be + activated or not. + + [..] + In Output or Alternate mode, each IO can be configured on open-drain or push-pull + type and the IO speed can be selected depending on the VDD value. + + [..] + All ports have external interrupt/event capability. To use external interrupt + lines, the port must be configured in input mode. All available GPIO pins are + connected to the 16 external interrupt/event lines from EXTI0 to EXTI15. + + [..] + The external interrupt/event controller consists of up to 20 edge detectors in connectivity + line devices, or 19 edge detectors in other devices for generating event/interrupt requests. + Each input line can be independently configured to select the type (event or interrupt) and + the corresponding trigger event (rising or falling or both). Each line can also masked + independently. A pending register maintains the status line of the interrupt requests + + ##### How to use this driver ##### + ============================================================================== + [..] + (#) Enable the GPIO APB2 clock using the following function : __HAL_RCC_GPIOx_CLK_ENABLE(). + + (#) Configure the GPIO pin(s) using HAL_GPIO_Init(). + (++) Configure the IO mode using "Mode" member from GPIO_InitTypeDef structure + (++) Activate Pull-up, Pull-down resistor using "Pull" member from GPIO_InitTypeDef + structure. + (++) In case of Output or alternate function mode selection: the speed is + configured through "Speed" member from GPIO_InitTypeDef structure + (++) Analog mode is required when a pin is to be used as ADC channel + or DAC output. + (++) In case of external interrupt/event selection the "Mode" member from + GPIO_InitTypeDef structure select the type (interrupt or event) and + the corresponding trigger event (rising or falling or both). + + (#) In case of external interrupt/event mode selection, configure NVIC IRQ priority + mapped to the EXTI line using HAL_NVIC_SetPriority() and enable it using + HAL_NVIC_EnableIRQ(). + + (#) To get the level of a pin configured in input mode use HAL_GPIO_ReadPin(). + + (#) To set/reset the level of a pin configured in output mode use + HAL_GPIO_WritePin()/HAL_GPIO_TogglePin(). + + (#) To lock pin configuration until next reset use HAL_GPIO_LockPin(). + + (#) During and just after reset, the alternate functions are not + active and the GPIO pins are configured in input floating mode (except JTAG + pins). + + (#) The LSE oscillator pins OSC32_IN and OSC32_OUT can be used as general purpose + (PC14 and PC15, respectively) when the LSE oscillator is off. The LSE has + priority over the GPIO function. + + (#) The HSE oscillator pins OSC_IN/OSC_OUT can be used as + general purpose PD0 and PD1, respectively, when the HSE oscillator is off. + The HSE has priority over the GPIO function. + + @endverbatim + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @defgroup GPIO GPIO + * @brief GPIO HAL module driver + * @{ + */ + +#ifdef HAL_GPIO_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/** @addtogroup GPIO_Private_Constants GPIO Private Constants + * @{ + */ +#define GPIO_MODE 0x00000003u +#define EXTI_MODE 0x10000000u +#define GPIO_MODE_IT 0x00010000u +#define GPIO_MODE_EVT 0x00020000u +#define RISING_EDGE 0x00100000u +#define FALLING_EDGE 0x00200000u +#define GPIO_OUTPUT_TYPE 0x00000010u + +#define GPIO_NUMBER 16u + +/* Definitions for bit manipulation of CRL and CRH register */ +#define GPIO_CR_MODE_INPUT 0x00000000u /*!< 00: Input mode (reset state) */ +#define GPIO_CR_CNF_ANALOG 0x00000000u /*!< 00: Analog mode */ +#define GPIO_CR_CNF_INPUT_FLOATING 0x00000004u /*!< 01: Floating input (reset state) */ +#define GPIO_CR_CNF_INPUT_PU_PD 0x00000008u /*!< 10: Input with pull-up / pull-down */ +#define GPIO_CR_CNF_GP_OUTPUT_PP 0x00000000u /*!< 00: General purpose output push-pull */ +#define GPIO_CR_CNF_GP_OUTPUT_OD 0x00000004u /*!< 01: General purpose output Open-drain */ +#define GPIO_CR_CNF_AF_OUTPUT_PP 0x00000008u /*!< 10: Alternate function output Push-pull */ +#define GPIO_CR_CNF_AF_OUTPUT_OD 0x0000000Cu /*!< 11: Alternate function output Open-drain */ + +/** + * @} + */ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ +/* Exported functions --------------------------------------------------------*/ +/** @defgroup GPIO_Exported_Functions GPIO Exported Functions + * @{ + */ + +/** @defgroup GPIO_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * +@verbatim + =============================================================================== + ##### Initialization and de-initialization functions ##### + =============================================================================== + [..] + This section provides functions allowing to initialize and de-initialize the GPIOs + to be ready for use. + +@endverbatim + * @{ + */ + + +/** + * @brief Initializes the GPIOx peripheral according to the specified parameters in the GPIO_Init. + * @param GPIOx: where x can be (A..G depending on device used) to select the GPIO peripheral + * @param GPIO_Init: pointer to a GPIO_InitTypeDef structure that contains + * the configuration information for the specified GPIO peripheral. + * @retval None + */ +void HAL_GPIO_Init(GPIO_TypeDef* GPIOx, GPIO_InitTypeDef* GPIO_Init) +{ + uint32_t position = 0x00u; + uint32_t ioposition; + uint32_t iocurrent; + uint32_t temp; + uint32_t config = 0x00u; + __IO uint32_t* configregister; /* Store the address of CRL or CRH register based on pin number */ + uint32_t registeroffset; /* offset used during computation of CNF and MODE bits placement inside CRL or CRH register */ + + /* Check the parameters */ + assert_param(IS_GPIO_ALL_INSTANCE(GPIOx)); + assert_param(IS_GPIO_PIN(GPIO_Init->Pin)); + assert_param(IS_GPIO_MODE(GPIO_Init->Mode)); + + /* Configure the port pins */ + while (((GPIO_Init->Pin) >> position) != 0x00u) + { + /* Get the IO position */ + ioposition = (0x01uL << position); + + /* Get the current IO position */ + iocurrent = (uint32_t)(GPIO_Init->Pin) & ioposition; + + if (iocurrent == ioposition) + { + /* Check the Alternate function parameters */ + assert_param(IS_GPIO_AF_INSTANCE(GPIOx)); + + /* Based on the required mode, filling config variable with MODEy[1:0] and CNFy[3:2] corresponding bits */ + switch (GPIO_Init->Mode) + { + /* If we are configuring the pin in OUTPUT push-pull mode */ + case GPIO_MODE_OUTPUT_PP: + /* Check the GPIO speed parameter */ + assert_param(IS_GPIO_SPEED(GPIO_Init->Speed)); + config = GPIO_Init->Speed + GPIO_CR_CNF_GP_OUTPUT_PP; + break; + + /* If we are configuring the pin in OUTPUT open-drain mode */ + case GPIO_MODE_OUTPUT_OD: + /* Check the GPIO speed parameter */ + assert_param(IS_GPIO_SPEED(GPIO_Init->Speed)); + config = GPIO_Init->Speed + GPIO_CR_CNF_GP_OUTPUT_OD; + break; + + /* If we are configuring the pin in ALTERNATE FUNCTION push-pull mode */ + case GPIO_MODE_AF_PP: + /* Check the GPIO speed parameter */ + assert_param(IS_GPIO_SPEED(GPIO_Init->Speed)); + config = GPIO_Init->Speed + GPIO_CR_CNF_AF_OUTPUT_PP; + break; + + /* If we are configuring the pin in ALTERNATE FUNCTION open-drain mode */ + case GPIO_MODE_AF_OD: + /* Check the GPIO speed parameter */ + assert_param(IS_GPIO_SPEED(GPIO_Init->Speed)); + config = GPIO_Init->Speed + GPIO_CR_CNF_AF_OUTPUT_OD; + break; + + /* If we are configuring the pin in INPUT (also applicable to EVENT and IT mode) */ + case GPIO_MODE_INPUT: + case GPIO_MODE_IT_RISING: + case GPIO_MODE_IT_FALLING: + case GPIO_MODE_IT_RISING_FALLING: + case GPIO_MODE_EVT_RISING: + case GPIO_MODE_EVT_FALLING: + case GPIO_MODE_EVT_RISING_FALLING: + /* Check the GPIO pull parameter */ + assert_param(IS_GPIO_PULL(GPIO_Init->Pull)); + + if (GPIO_Init->Pull == GPIO_NOPULL) + { + config = GPIO_CR_MODE_INPUT + GPIO_CR_CNF_INPUT_FLOATING; + } + else if (GPIO_Init->Pull == GPIO_PULLUP) + { + config = GPIO_CR_MODE_INPUT + GPIO_CR_CNF_INPUT_PU_PD; + + /* Set the corresponding ODR bit */ + GPIOx->BSRR = ioposition; + } + else /* GPIO_PULLDOWN */ + { + config = GPIO_CR_MODE_INPUT + GPIO_CR_CNF_INPUT_PU_PD; + + /* Reset the corresponding ODR bit */ + GPIOx->BRR = ioposition; + } + + break; + + /* If we are configuring the pin in INPUT analog mode */ + case GPIO_MODE_ANALOG: + config = GPIO_CR_MODE_INPUT + GPIO_CR_CNF_ANALOG; + break; + + /* Parameters are checked with assert_param */ + default: + break; + } + + /* Check if the current bit belongs to first half or last half of the pin count number + in order to address CRH or CRL register*/ + configregister = (iocurrent < GPIO_PIN_8) ? &GPIOx->CRL : &GPIOx->CRH; + registeroffset = (iocurrent < GPIO_PIN_8) ? (position << 2u) : ((position - 8u) << 2u); + + /* Apply the new configuration of the pin to the register */ + MODIFY_REG((*configregister), ((GPIO_CRL_MODE0 | GPIO_CRL_CNF0) << registeroffset), (config << registeroffset)); + + /*--------------------- EXTI Mode Configuration ------------------------*/ + /* Configure the External Interrupt or event for the current IO */ + if ((GPIO_Init->Mode & EXTI_MODE) == EXTI_MODE) + { + /* Enable AFIO Clock */ + __HAL_RCC_AFIO_CLK_ENABLE(); + temp = AFIO->EXTICR[position >> 2u]; + CLEAR_BIT(temp, (0x0Fu) << (4u * (position & 0x03u))); + SET_BIT(temp, (GPIO_GET_INDEX(GPIOx)) << (4u * (position & 0x03u))); + AFIO->EXTICR[position >> 2u] = temp; + + + /* Configure the interrupt mask */ + if ((GPIO_Init->Mode & GPIO_MODE_IT) == GPIO_MODE_IT) + { + SET_BIT(EXTI->IMR, iocurrent); + } + else + { + CLEAR_BIT(EXTI->IMR, iocurrent); + } + + /* Configure the event mask */ + if ((GPIO_Init->Mode & GPIO_MODE_EVT) == GPIO_MODE_EVT) + { + SET_BIT(EXTI->EMR, iocurrent); + } + else + { + CLEAR_BIT(EXTI->EMR, iocurrent); + } + + /* Enable or disable the rising trigger */ + if ((GPIO_Init->Mode & RISING_EDGE) == RISING_EDGE) + { + SET_BIT(EXTI->RTSR, iocurrent); + } + else + { + CLEAR_BIT(EXTI->RTSR, iocurrent); + } + + /* Enable or disable the falling trigger */ + if ((GPIO_Init->Mode & FALLING_EDGE) == FALLING_EDGE) + { + SET_BIT(EXTI->FTSR, iocurrent); + } + else + { + CLEAR_BIT(EXTI->FTSR, iocurrent); + } + } + } + + position++; + } +} + +/** + * @brief De-initializes the GPIOx peripheral registers to their default reset values. + * @param GPIOx: where x can be (A..G depending on device used) to select the GPIO peripheral + * @param GPIO_Pin: specifies the port bit to be written. + * This parameter can be one of GPIO_PIN_x where x can be (0..15). + * @retval None + */ +void HAL_GPIO_DeInit(GPIO_TypeDef* GPIOx, uint32_t GPIO_Pin) +{ + uint32_t position = 0x00u; + uint32_t iocurrent; + uint32_t tmp; + __IO uint32_t* configregister; /* Store the address of CRL or CRH register based on pin number */ + uint32_t registeroffset; + + /* Check the parameters */ + assert_param(IS_GPIO_ALL_INSTANCE(GPIOx)); + assert_param(IS_GPIO_PIN(GPIO_Pin)); + + /* Configure the port pins */ + while ((GPIO_Pin >> position) != 0u) + { + /* Get current io position */ + iocurrent = (GPIO_Pin) & (1uL << position); + + if (iocurrent) + { + /*------------------------- EXTI Mode Configuration --------------------*/ + /* Clear the External Interrupt or Event for the current IO */ + + tmp = AFIO->EXTICR[position >> 2u]; + tmp &= 0x0FuL << (4u * (position & 0x03u)); + + if (tmp == (GPIO_GET_INDEX(GPIOx) << (4u * (position & 0x03u)))) + { + tmp = 0x0FuL << (4u * (position & 0x03u)); + CLEAR_BIT(AFIO->EXTICR[position >> 2u], tmp); + + /* Clear EXTI line configuration */ + CLEAR_BIT(EXTI->IMR, (uint32_t)iocurrent); + CLEAR_BIT(EXTI->EMR, (uint32_t)iocurrent); + + /* Clear Rising Falling edge configuration */ + CLEAR_BIT(EXTI->RTSR, (uint32_t)iocurrent); + CLEAR_BIT(EXTI->FTSR, (uint32_t)iocurrent); + } + + /*------------------------- GPIO Mode Configuration --------------------*/ + /* Check if the current bit belongs to first half or last half of the pin count number + in order to address CRH or CRL register */ + configregister = (iocurrent < GPIO_PIN_8) ? &GPIOx->CRL : &GPIOx->CRH; + registeroffset = (iocurrent < GPIO_PIN_8) ? (position << 2u) : ((position - 8u) << 2u); + + /* CRL/CRH default value is floating input(0x04) shifted to correct position */ + MODIFY_REG(*configregister, ((GPIO_CRL_MODE0 | GPIO_CRL_CNF0) << registeroffset), GPIO_CRL_CNF0_0 << registeroffset); + + /* ODR default value is 0 */ + CLEAR_BIT(GPIOx->ODR, iocurrent); + } + + position++; + } +} + +/** + * @} + */ + +/** @defgroup GPIO_Exported_Functions_Group2 IO operation functions + * @brief GPIO Read and Write + * +@verbatim + =============================================================================== + ##### IO operation functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to manage the GPIOs. + +@endverbatim + * @{ + */ + +/** + * @brief Reads the specified input port pin. + * @param GPIOx: where x can be (A..G depending on device used) to select the GPIO peripheral + * @param GPIO_Pin: specifies the port bit to read. + * This parameter can be GPIO_PIN_x where x can be (0..15). + * @retval The input port pin value. + */ +GPIO_PinState HAL_GPIO_ReadPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin) +{ + GPIO_PinState bitstatus; + + /* Check the parameters */ + assert_param(IS_GPIO_PIN(GPIO_Pin)); + + if ((GPIOx->IDR & GPIO_Pin) != (uint32_t)GPIO_PIN_RESET) + { + bitstatus = GPIO_PIN_SET; + } + else + { + bitstatus = GPIO_PIN_RESET; + } + + return bitstatus; +} + +/** + * @brief Sets or clears the selected data port bit. + * + * @note This function uses GPIOx_BSRR register to allow atomic read/modify + * accesses. In this way, there is no risk of an IRQ occurring between + * the read and the modify access. + * + * @param GPIOx: where x can be (A..G depending on device used) to select the GPIO peripheral + * @param GPIO_Pin: specifies the port bit to be written. + * This parameter can be one of GPIO_PIN_x where x can be (0..15). + * @param PinState: specifies the value to be written to the selected bit. + * This parameter can be one of the GPIO_PinState enum values: + * @arg GPIO_PIN_RESET: to clear the port pin + * @arg GPIO_PIN_SET: to set the port pin + * @retval None + */ +void HAL_GPIO_WritePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState) +{ + /* Check the parameters */ + assert_param(IS_GPIO_PIN(GPIO_Pin)); + assert_param(IS_GPIO_PIN_ACTION(PinState)); + + if (PinState != GPIO_PIN_RESET) + { + GPIOx->BSRR = GPIO_Pin; + } + else + { + GPIOx->BSRR = (uint32_t)GPIO_Pin << 16u; + } +} + +/** + * @brief Toggles the specified GPIO pin + * @param GPIOx: where x can be (A..G depending on device used) to select the GPIO peripheral + * @param GPIO_Pin: Specifies the pins to be toggled. + * @retval None + */ +void HAL_GPIO_TogglePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin) +{ + /* Check the parameters */ + assert_param(IS_GPIO_PIN(GPIO_Pin)); + + if ((GPIOx->ODR & GPIO_Pin) != 0x00u) + { + GPIOx->BRR = (uint32_t)GPIO_Pin; + } + else + { + GPIOx->BSRR = (uint32_t)GPIO_Pin; + } +} + +/** +* @brief Locks GPIO Pins configuration registers. +* @note The locking mechanism allows the IO configuration to be frozen. When the LOCK sequence +* has been applied on a port bit, it is no longer possible to modify the value of the port bit until +* the next reset. +* @param GPIOx: where x can be (A..G depending on device used) to select the GPIO peripheral +* @param GPIO_Pin: specifies the port bit to be locked. +* This parameter can be any combination of GPIO_Pin_x where x can be (0..15). +* @retval None +*/ +HAL_StatusTypeDef HAL_GPIO_LockPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin) +{ + __IO uint32_t tmp = GPIO_LCKR_LCKK; + + /* Check the parameters */ + assert_param(IS_GPIO_LOCK_INSTANCE(GPIOx)); + assert_param(IS_GPIO_PIN(GPIO_Pin)); + + /* Apply lock key write sequence */ + SET_BIT(tmp, GPIO_Pin); + /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */ + GPIOx->LCKR = tmp; + /* Reset LCKx bit(s): LCKK='0' + LCK[15-0] */ + GPIOx->LCKR = GPIO_Pin; + /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */ + GPIOx->LCKR = tmp; + /* Read LCKK register. This read is mandatory to complete key lock sequence */ + tmp = GPIOx->LCKR; + + /* read again in order to confirm lock is active */ + if ((uint32_t)(GPIOx->LCKR & GPIO_LCKR_LCKK)) + { + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @brief This function handles EXTI interrupt request. + * @param GPIO_Pin: Specifies the pins connected EXTI line + * @retval None + */ +void HAL_GPIO_EXTI_IRQHandler(uint16_t GPIO_Pin) +{ + /* EXTI line interrupt detected */ + if (__HAL_GPIO_EXTI_GET_IT(GPIO_Pin) != 0x00u) + { + __HAL_GPIO_EXTI_CLEAR_IT(GPIO_Pin); + HAL_GPIO_EXTI_Callback(GPIO_Pin); + } +} + +/** + * @brief EXTI line detection callbacks. + * @param GPIO_Pin: Specifies the pins connected EXTI line + * @retval None + */ +__weak void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(GPIO_Pin); + /* NOTE: This function Should not be modified, when the callback is needed, + the HAL_GPIO_EXTI_Callback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_GPIO_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_gpio_ex.c b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_gpio_ex.c new file mode 100644 index 00000000..621b8256 --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_gpio_ex.c @@ -0,0 +1,127 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_gpio_ex.c + * @author MCD Application Team + * @brief GPIO Extension HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the General Purpose Input/Output (GPIO) extension peripheral. + * + Extended features functions + * + @verbatim + ============================================================================== + ##### GPIO Peripheral extension features ##### + ============================================================================== + [..] GPIO module on STM32F1 family, manage also the AFIO register: + (+) Possibility to use the EVENTOUT Cortex feature + + ##### How to use this driver ##### + ============================================================================== + [..] This driver provides functions to use EVENTOUT Cortex feature + (#) Configure EVENTOUT Cortex feature using the function HAL_GPIOEx_ConfigEventout() + (#) Activate EVENTOUT Cortex feature using the HAL_GPIOEx_EnableEventout() + (#) Deactivate EVENTOUT Cortex feature using the HAL_GPIOEx_DisableEventout() + + @endverbatim + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @defgroup GPIOEx GPIOEx + * @brief GPIO HAL module driver + * @{ + */ + +#ifdef HAL_GPIO_MODULE_ENABLED + +/** @defgroup GPIOEx_Exported_Functions GPIOEx Exported Functions + * @{ + */ + +/** @defgroup GPIOEx_Exported_Functions_Group1 Extended features functions + * @brief Extended features functions + * +@verbatim + ============================================================================== + ##### Extended features functions ##### + ============================================================================== + [..] This section provides functions allowing to: + (+) Configure EVENTOUT Cortex feature using the function HAL_GPIOEx_ConfigEventout() + (+) Activate EVENTOUT Cortex feature using the HAL_GPIOEx_EnableEventout() + (+) Deactivate EVENTOUT Cortex feature using the HAL_GPIOEx_DisableEventout() + +@endverbatim + * @{ + */ + +/** + * @brief Configures the port and pin on which the EVENTOUT Cortex signal will be connected. + * @param GPIO_PortSource Select the port used to output the Cortex EVENTOUT signal. + * This parameter can be a value of @ref GPIOEx_EVENTOUT_PORT. + * @param GPIO_PinSource Select the pin used to output the Cortex EVENTOUT signal. + * This parameter can be a value of @ref GPIOEx_EVENTOUT_PIN. + * @retval None + */ +void HAL_GPIOEx_ConfigEventout(uint32_t GPIO_PortSource, uint32_t GPIO_PinSource) +{ + /* Verify the parameters */ + assert_param(IS_AFIO_EVENTOUT_PORT(GPIO_PortSource)); + assert_param(IS_AFIO_EVENTOUT_PIN(GPIO_PinSource)); + + /* Apply the new configuration */ + MODIFY_REG(AFIO->EVCR, (AFIO_EVCR_PORT) | (AFIO_EVCR_PIN), (GPIO_PortSource) | (GPIO_PinSource)); +} + +/** + * @brief Enables the Event Output. + * @retval None + */ +void HAL_GPIOEx_EnableEventout(void) +{ + SET_BIT(AFIO->EVCR, AFIO_EVCR_EVOE); +} + +/** + * @brief Disables the Event Output. + * @retval None + */ +void HAL_GPIOEx_DisableEventout(void) +{ + CLEAR_BIT(AFIO->EVCR, AFIO_EVCR_EVOE); +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_GPIO_MODULE_ENABLED */ + +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr.c b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_pwr.c similarity index 54% rename from EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr.c rename to EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_pwr.c index 3f63e1ef..d2c63737 100644 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr.c +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_pwr.c @@ -1,54 +1,37 @@ /** ****************************************************************************** - * @file stm32f4xx_hal_pwr.c + * @file stm32f1xx_hal_pwr.c * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 * @brief PWR HAL module driver. + * * This file provides firmware functions to manage the following * functionalities of the Power Controller (PWR) peripheral: - * + Initialization and de-initialization functions + * + Initialization/de-initialization functions * + Peripheral Control functions * ****************************************************************************** * @attention * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

* - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause * ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" +#include "stm32f1xx_hal.h" -/** @addtogroup STM32F4xx_HAL_Driver +/** @addtogroup STM32F1xx_HAL_Driver * @{ */ /** @defgroup PWR PWR - * @brief PWR HAL module driver + * @brief PWR HAL module driver * @{ */ @@ -56,35 +39,98 @@ /* Private typedef -----------------------------------------------------------*/ /* Private define ------------------------------------------------------------*/ -/** @addtogroup PWR_Private_Constants + +/** @defgroup PWR_Private_Constants PWR Private Constants * @{ */ /** @defgroup PWR_PVD_Mode_Mask PWR PVD Mode Mask * @{ */ -#define PVD_MODE_IT ((uint32_t)0x00010000U) -#define PVD_MODE_EVT ((uint32_t)0x00020000U) -#define PVD_RISING_EDGE ((uint32_t)0x00000001U) -#define PVD_FALLING_EDGE ((uint32_t)0x00000002U) +#define PVD_MODE_IT 0x00010000U +#define PVD_MODE_EVT 0x00020000U +#define PVD_RISING_EDGE 0x00000001U +#define PVD_FALLING_EDGE 0x00000002U +/** + * @} + */ + + +/** @defgroup PWR_register_alias_address PWR Register alias address + * @{ + */ +/* ------------- PWR registers bit address in the alias region ---------------*/ +#define PWR_OFFSET (PWR_BASE - PERIPH_BASE) +#define PWR_CR_OFFSET 0x00U +#define PWR_CSR_OFFSET 0x04U +#define PWR_CR_OFFSET_BB (PWR_OFFSET + PWR_CR_OFFSET) +#define PWR_CSR_OFFSET_BB (PWR_OFFSET + PWR_CSR_OFFSET) +/** + * @} + */ + +/** @defgroup PWR_CR_register_alias PWR CR Register alias address + * @{ + */ +/* --- CR Register ---*/ +/* Alias word address of LPSDSR bit */ +#define LPSDSR_BIT_NUMBER PWR_CR_LPDS_Pos +#define CR_LPSDSR_BB ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (LPSDSR_BIT_NUMBER * 4U))) + +/* Alias word address of DBP bit */ +#define DBP_BIT_NUMBER PWR_CR_DBP_Pos +#define CR_DBP_BB ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (DBP_BIT_NUMBER * 4U))) + +/* Alias word address of PVDE bit */ +#define PVDE_BIT_NUMBER PWR_CR_PVDE_Pos +#define CR_PVDE_BB ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (PVDE_BIT_NUMBER * 4U))) + /** * @} */ +/** @defgroup PWR_CSR_register_alias PWR CSR Register alias address + * @{ + */ + +/* --- CSR Register ---*/ +/* Alias word address of EWUP1 bit */ +#define CSR_EWUP_BB(VAL) ((uint32_t)(PERIPH_BB_BASE + (PWR_CSR_OFFSET_BB * 32U) + (POSITION_VAL(VAL) * 4U))) /** * @} */ -/* Private macro -------------------------------------------------------------*/ + +/** + * @} + */ + /* Private variables ---------------------------------------------------------*/ /* Private function prototypes -----------------------------------------------*/ +/** @defgroup PWR_Private_Functions PWR Private Functions + * brief WFE cortex command overloaded for HAL_PWR_EnterSTOPMode usage only (see Workaround section) + * @{ + */ +static void PWR_OverloadWfe(void); + /* Private functions ---------------------------------------------------------*/ +__NOINLINE +static void PWR_OverloadWfe(void) +{ + __asm volatile( "wfe" ); + __asm volatile( "nop" ); +} + +/** + * @} + */ + /** @defgroup PWR_Exported_Functions PWR Exported Functions * @{ */ /** @defgroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions - * @brief Initialization and de-initialization functions + * @brief Initialization and de-initialization functions * @verbatim =============================================================================== @@ -92,7 +138,7 @@ =============================================================================== [..] After reset, the backup domain (RTC registers, RTC backup data - registers and backup SRAM) is protected against possible unwanted + registers) is protected against possible unwanted write accesses. To enable access to the RTC Domain and RTC registers, proceed as follows: (+) Enable the Power Controller (PWR) APB1 interface clock using the @@ -104,7 +150,7 @@ */ /** - * @brief Deinitializes the HAL PWR peripheral registers to their default reset values. + * @brief Deinitializes the PWR peripheral registers to their default reset values. * @retval None */ void HAL_PWR_DeInit(void) @@ -114,26 +160,28 @@ void HAL_PWR_DeInit(void) } /** - * @brief Enables access to the backup domain (RTC registers, RTC - * backup data registers and backup SRAM). - * @note If the HSE divided by 2, 3, ..31 is used as the RTC clock, the + * @brief Enables access to the backup domain (RTC registers, RTC + * backup data registers ). + * @note If the HSE divided by 128 is used as the RTC clock, the * Backup Domain Access should be kept enabled. * @retval None */ void HAL_PWR_EnableBkUpAccess(void) { + /* Enable access to RTC and backup registers */ *(__IO uint32_t*) CR_DBP_BB = (uint32_t)ENABLE; } /** - * @brief Disables access to the backup domain (RTC registers, RTC - * backup data registers and backup SRAM). - * @note If the HSE divided by 2, 3, ..31 is used as the RTC clock, the + * @brief Disables access to the backup domain (RTC registers, RTC + * backup data registers). + * @note If the HSE divided by 128 is used as the RTC clock, the * Backup Domain Access should be kept enabled. * @retval None */ void HAL_PWR_DisableBkUpAccess(void) { + /* Disable access to RTC and backup registers */ *(__IO uint32_t*) CR_DBP_BB = (uint32_t)DISABLE; } @@ -142,10 +190,9 @@ void HAL_PWR_DisableBkUpAccess(void) */ /** @defgroup PWR_Exported_Functions_Group2 Peripheral Control functions - * @brief Low Power modes configuration functions + * @brief Low Power modes configuration functions * @verbatim - =============================================================================== ##### Peripheral Control functions ##### =============================================================================== @@ -155,114 +202,113 @@ void HAL_PWR_DisableBkUpAccess(void) [..] (+) The PVD is used to monitor the VDD power supply by comparing it to a threshold selected by the PVD Level (PLS[2:0] bits in the PWR_CR). + (+) A PVDO flag is available to indicate if VDD/VDDA is higher or lower than the PVD threshold. This event is internally connected to the EXTI line16 and can generate an interrupt if enabled. This is done through - __HAL_PWR_PVD_EXTI_ENABLE_IT() macro. + __HAL_PVD_EXTI_ENABLE_IT() macro. (+) The PVD is stopped in Standby mode. - *** Wake-up pin configuration *** + *** WakeUp pin configuration *** ================================ [..] - (+) Wake-up pin is used to wake up the system from Standby mode. This pin is + (+) WakeUp pin is used to wake up the system from Standby mode. This pin is forced in input pull-down configuration and is active on rising edges. - (+) There is one Wake-up pin: Wake-up Pin 1 on PA.00. - (++) For STM32F446xx there are two Wake-Up pins: Pin1 on PA.00 and Pin2 on PC.13 - (++) For STM32F410xx/STM32F412Zx/STM32F412Rx/STM32F412Vx/STM32F412Cx there are three Wake-Up pins: Pin1 on PA.00, Pin2 on PC.00 and Pin3 on PC.01 + (+) There is one WakeUp pin: + WakeUp Pin 1 on PA.00. + + [..] *** Low Power modes configuration *** ===================================== - [..] - The devices feature 3 low-power modes: - (+) Sleep mode: Cortex-M4 core stopped, peripherals kept running. - (+) Stop mode: all clocks are stopped, regulator running, regulator - in low power mode - (+) Standby mode: 1.2V domain powered off. + [..] + The device features 3 low-power modes: + (+) Sleep mode: CPU clock off, all peripherals including Cortex-M3 core peripherals like + NVIC, SysTick, etc. are kept running + (+) Stop mode: All clocks are stopped + (+) Standby mode: 1.8V domain powered off + *** Sleep mode *** ================== [..] (+) Entry: - The Sleep mode is entered by using the HAL_PWR_EnterSLEEPMode(PWR_MAINREGULATOR_ON, PWR_SLEEPENTRY_WFI) + The Sleep mode is entered by using the HAL_PWR_EnterSLEEPMode(PWR_MAINREGULATOR_ON, PWR_SLEEPENTRY_WFx) functions with (++) PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction (++) PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction - -@@- The Regulator parameter is not used for the STM32F4 family - and is kept as parameter just to maintain compatibility with the - lower power families (STM32L). (+) Exit: - Any peripheral interrupt acknowledged by the nested vectored interrupt - controller (NVIC) can wake up the device from Sleep mode. + (++) WFI entry mode, Any peripheral interrupt acknowledged by the nested vectored interrupt + controller (NVIC) can wake up the device from Sleep mode. + (++) WFE entry mode, Any wakeup event can wake up the device from Sleep mode. + (+++) Any peripheral interrupt w/o NVIC configuration & SEVONPEND bit set in the Cortex (HAL_PWR_EnableSEVOnPend) + (+++) Any EXTI Line (Internal or External) configured in Event mode *** Stop mode *** ================= [..] - In Stop mode, all clocks in the 1.2V domain are stopped, the PLL, the HSI, - and the HSE RC oscillators are disabled. Internal SRAM and register contents - are preserved. - The voltage regulator can be configured either in normal or low-power mode. - To minimize the consumption In Stop mode, FLASH can be powered off before - entering the Stop mode using the HAL_PWREx_EnableFlashPowerDown() function. - It can be switched on again by software after exiting the Stop mode using - the HAL_PWREx_DisableFlashPowerDown() function. + The Stop mode is based on the Cortex-M3 deepsleep mode combined with peripheral + clock gating. The voltage regulator can be configured either in normal or low-power mode. + In Stop mode, all clocks in the 1.8 V domain are stopped, the PLL, the HSI and the HSE RC + oscillators are disabled. SRAM and register contents are preserved. + In Stop mode, all I/O pins keep the same state as in Run mode. (+) Entry: - The Stop mode is entered using the HAL_PWR_EnterSTOPMode(PWR_MAINREGULATOR_ON) + The Stop mode is entered using the HAL_PWR_EnterSTOPMode(PWR_REGULATOR_VALUE, PWR_SLEEPENTRY_WFx ) function with: - (++) Main regulator ON. - (++) Low Power regulator ON. + (++) PWR_REGULATOR_VALUE= PWR_MAINREGULATOR_ON: Main regulator ON. + (++) PWR_REGULATOR_VALUE= PWR_LOWPOWERREGULATOR_ON: Low Power regulator ON. + (++) PWR_SLEEPENTRY_WFx= PWR_SLEEPENTRY_WFI: enter STOP mode with WFI instruction + (++) PWR_SLEEPENTRY_WFx= PWR_SLEEPENTRY_WFE: enter STOP mode with WFE instruction (+) Exit: - Any EXTI Line (Internal or External) configured in Interrupt/Event mode. + (++) WFI entry mode, Any EXTI Line (Internal or External) configured in Interrupt mode with NVIC configured + (++) WFE entry mode, Any EXTI Line (Internal or External) configured in Event mode. *** Standby mode *** ==================== - [..] - (+) - The Standby mode allows to achieve the lowest power consumption. It is based - on the Cortex-M4 deep sleep mode, with the voltage regulator disabled. - The 1.2V domain is consequently powered off. The PLL, the HSI oscillator and - the HSE oscillator are also switched off. SRAM and register contents are lost - except for the RTC registers, RTC backup registers, backup SRAM and Standby - circuitry. - - The voltage regulator is OFF. - - (++) Entry: - (+++) The Standby mode is entered using the HAL_PWR_EnterSTANDBYMode() function. - (++) Exit: - (+++) WKUP pin rising edge, RTC alarm (Alarm A and Alarm B), RTC wake-up, - tamper event, time-stamp event, external reset in NRST pin, IWDG reset. - - *** Auto-wake-up (AWU) from low-power mode *** - ============================================= - [..] + [..] + The Standby mode allows to achieve the lowest power consumption. It is based on the + Cortex-M3 deepsleep mode, with the voltage regulator disabled. The 1.8 V domain is + consequently powered off. The PLL, the HSI oscillator and the HSE oscillator are also + switched off. SRAM and register contents are lost except for registers in the Backup domain + and Standby circuitry + + (+) Entry: + (++) The Standby mode is entered using the HAL_PWR_EnterSTANDBYMode() function. + (+) Exit: + (++) WKUP pin rising edge, RTC alarm event rising edge, external Reset in + NRSTpin, IWDG Reset + + *** Auto-wakeup (AWU) from low-power mode *** + ============================================= + [..] - (+) The MCU can be woken up from low-power mode by an RTC Alarm event, an RTC - Wake-up event, a tamper event or a time-stamp event, without depending on - an external interrupt (Auto-wake-up mode). + (+) The MCU can be woken up from low-power mode by an RTC Alarm event, + without depending on an external interrupt (Auto-wakeup mode). - (+) RTC auto-wake-up (AWU) from the Stop and Standby modes + (+) RTC auto-wakeup (AWU) from the Stop and Standby modes - (++) To wake up from the Stop mode with an RTC alarm event, it is necessary to - configure the RTC to generate the RTC alarm using the HAL_RTC_SetAlarm_IT() function. + (++) To wake up from the Stop mode with an RTC alarm event, it is necessary to + configure the RTC to generate the RTC alarm using the HAL_RTC_SetAlarm_IT() function. - (++) To wake up from the Stop mode with an RTC Tamper or time stamp event, it - is necessary to configure the RTC to detect the tamper or time stamp event using the - HAL_RTCEx_SetTimeStamp_IT() or HAL_RTCEx_SetTamper_IT() functions. + *** PWR Workarounds linked to Silicon Limitation *** + ==================================================== + [..] + Below the list of all silicon limitations known on STM32F1xx prouct. - (++) To wake up from the Stop mode with an RTC Wake-up event, it is necessary to - configure the RTC to generate the RTC Wake-up event using the HAL_RTCEx_SetWakeUpTimer_IT() function. + (#)Workarounds Implemented inside PWR HAL Driver + (##)Debugging Stop mode with WFE entry - overloaded the WFE by an internal function @endverbatim * @{ */ /** - * @brief Configures the voltage threshold detected by the Power Voltage Detector(PVD). - * @param sConfigPVD: pointer to an PWR_PVDTypeDef structure that contains the configuration - * information for the PVD. - * @note Refer to the electrical characteristics of your device datasheet for + * @brief Configures the voltage threshold detected by the Power Voltage Detector(PVD). + * @param sConfigPVD: pointer to an PWR_PVDTypeDef structure that contains the configuration + * information for the PVD. + * @note Refer to the electrical characteristics of your device datasheet for * more details about the voltage threshold corresponding to each * detection level. * @retval None @@ -272,13 +318,15 @@ void HAL_PWR_ConfigPVD(PWR_PVDTypeDef* sConfigPVD) /* Check the parameters */ assert_param(IS_PWR_PVD_LEVEL(sConfigPVD->PVDLevel)); assert_param(IS_PWR_PVD_MODE(sConfigPVD->Mode)); + /* Set PLS[7:5] bits according to PVDLevel value */ MODIFY_REG(PWR->CR, PWR_CR_PLS, sConfigPVD->PVDLevel); + /* Clear any previous config. Keep it clear if no event or IT mode is selected */ __HAL_PWR_PVD_EXTI_DISABLE_EVENT(); __HAL_PWR_PVD_EXTI_DISABLE_IT(); - __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE(); __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE(); + __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE(); /* Configure interrupt mode */ if ((sConfigPVD->Mode & PVD_MODE_IT) == PVD_MODE_IT) @@ -305,73 +353,63 @@ void HAL_PWR_ConfigPVD(PWR_PVDTypeDef* sConfigPVD) } /** - * @brief Enables the Power Voltage Detector(PVD). + * @brief Enables the Power Voltage Detector(PVD). * @retval None */ void HAL_PWR_EnablePVD(void) { + /* Enable the power voltage detector */ *(__IO uint32_t*) CR_PVDE_BB = (uint32_t)ENABLE; } /** - * @brief Disables the Power Voltage Detector(PVD). + * @brief Disables the Power Voltage Detector(PVD). * @retval None */ void HAL_PWR_DisablePVD(void) { + /* Disable the power voltage detector */ *(__IO uint32_t*) CR_PVDE_BB = (uint32_t)DISABLE; } /** - * @brief Enables the Wake-up PINx functionality. + * @brief Enables the WakeUp PINx functionality. * @param WakeUpPinx: Specifies the Power Wake-Up pin to enable. - * This parameter can be one of the following values: + * This parameter can be one of the following values: * @arg PWR_WAKEUP_PIN1 - * @arg PWR_WAKEUP_PIN2 available only on STM32F410xx/STM32F446xx/STM32F412Zx/STM32F412Rx/STM32F412Vx/STM32F412Cx devices - * @arg PWR_WAKEUP_PIN3 available only on STM32F410xx/STM32F412xx devices * @retval None */ void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx) { /* Check the parameter */ assert_param(IS_PWR_WAKEUP_PIN(WakeUpPinx)); - /* Enable the wake up pin */ - SET_BIT(PWR->CSR, WakeUpPinx); + /* Enable the EWUPx pin */ + *(__IO uint32_t*) CSR_EWUP_BB(WakeUpPinx) = (uint32_t)ENABLE; } /** - * @brief Disables the Wake-up PINx functionality. + * @brief Disables the WakeUp PINx functionality. * @param WakeUpPinx: Specifies the Power Wake-Up pin to disable. - * This parameter can be one of the following values: + * This parameter can be one of the following values: * @arg PWR_WAKEUP_PIN1 - * @arg PWR_WAKEUP_PIN2 available only on STM32F410xx/STM32F446xx/STM32F412Zx/STM32F412Rx/STM32F412Vx/STM32F412Cx devices - * @arg PWR_WAKEUP_PIN3 available only on STM32F410xx/STM32F412Zx/STM32F412Rx/STM32F412Vx/STM32F412Cx devices * @retval None */ void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx) { /* Check the parameter */ assert_param(IS_PWR_WAKEUP_PIN(WakeUpPinx)); - /* Disable the wake up pin */ - CLEAR_BIT(PWR->CSR, WakeUpPinx); + /* Disable the EWUPx pin */ + *(__IO uint32_t*) CSR_EWUP_BB(WakeUpPinx) = (uint32_t)DISABLE; } /** * @brief Enters Sleep mode. - * - * @note In Sleep mode, all I/O pins keep the same state as in Run mode. - * - * @note In Sleep mode, the systick is stopped to avoid exit from this mode with - * systick interrupt when used as time base for Timeout - * - * @param Regulator: Specifies the regulator state in SLEEP mode. - * This parameter can be one of the following values: - * @arg PWR_MAINREGULATOR_ON: SLEEP mode with regulator ON - * @arg PWR_LOWPOWERREGULATOR_ON: SLEEP mode with low power regulator ON - * @note This parameter is not used for the STM32F4 family and is kept as parameter - * just to maintain compatibility with the lower power families. - * @param SLEEPEntry: Specifies if SLEEP mode in entered with WFI or WFE instruction. - * This parameter can be one of the following values: + * @note In Sleep mode, all I/O pins keep the same state as in Run mode. + * @param Regulator: Regulator state as no effect in SLEEP mode - allows to support portability from legacy software + * @param SLEEPEntry: Specifies if SLEEP mode is entered with WFI or WFE instruction. + * When WFI entry is used, tick interrupt have to be disabled if not desired as + * the interrupt wake up source. + * This parameter can be one of the following values: * @arg PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction * @arg PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction * @retval None @@ -379,8 +417,12 @@ void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx) void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry) { /* Check the parameters */ - assert_param(IS_PWR_REGULATOR(Regulator)); + /* No check on Regulator because parameter not used in SLEEP mode */ + /* Prevent unused argument(s) compilation warning */ + UNUSED(Regulator); + assert_param(IS_PWR_SLEEP_ENTRY(SLEEPEntry)); + /* Clear SLEEPDEEP bit of Cortex System Control Register */ CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk)); @@ -401,10 +443,10 @@ void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry) /** * @brief Enters Stop mode. - * @note In Stop mode, all I/O pins keep the same state as in Run mode. - * @note When exiting Stop mode by issuing an interrupt or a wake-up event, - * the HSI RC oscillator is selected as system clock. - * @note When the voltage regulator operates in low power mode, an additional + * @note In Stop mode, all I/O pins keep the same state as in Run mode. + * @note When exiting Stop mode by using an interrupt or a wakeup event, + * HSI RC oscillator is selected as system clock. + * @note When the voltage regulator operates in low power mode, an additional * startup delay is incurred when waking up from Stop mode. * By keeping the internal regulator ON during Stop mode, the consumption * is higher although the startup time is reduced. @@ -423,8 +465,13 @@ void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry) /* Check the parameters */ assert_param(IS_PWR_REGULATOR(Regulator)); assert_param(IS_PWR_STOP_ENTRY(STOPEntry)); - /* Select the regulator state in Stop mode: Set PDDS and LPDS bits according to PWR_Regulator value */ - MODIFY_REG(PWR->CR, (PWR_CR_PDDS | PWR_CR_LPDS), Regulator); + + /* Clear PDDS bit in PWR register to specify entering in STOP mode when CPU enter in Deepsleep */ + CLEAR_BIT(PWR->CR, PWR_CR_PDDS); + + /* Select the voltage regulator mode by setting LPDS bit in PWR register according to Regulator parameter value */ + MODIFY_REG(PWR->CR, PWR_CR_LPDS, Regulator); + /* Set SLEEPDEEP bit of Cortex System Control Register */ SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk)); @@ -438,8 +485,8 @@ void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry) { /* Request Wait For Event */ __SEV(); - __WFE(); - __WFE(); + PWR_OverloadWfe(); /* WFE redefine locally */ + PWR_OverloadWfe(); /* WFE redefine locally */ } /* Reset SLEEPDEEP bit of Cortex System Control Register */ @@ -448,20 +495,20 @@ void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry) /** * @brief Enters Standby mode. - * @note In Standby mode, all I/O pins are high impedance except for: + * @note In Standby mode, all I/O pins are high impedance except for: * - Reset pad (still available) - * - RTC_AF1 pin (PC13) if configured for tamper, time-stamp, RTC - * Alarm out, or RTC clock calibration out. - * - RTC_AF2 pin (PI8) if configured for tamper or time-stamp. - * - WKUP pin 1 (PA0) if enabled. + * - TAMPER pin if configured for tamper or calibration out. + * - WKUP pin (PA0) if enabled. * @retval None */ void HAL_PWR_EnterSTANDBYMode(void) { /* Select Standby mode */ SET_BIT(PWR->CR, PWR_CR_PDDS); + /* Set SLEEPDEEP bit of Cortex System Control Register */ SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk)); + /* This option is used to ensure that store operations are completed */ #if defined ( __CC_ARM) __force_stores(); @@ -470,33 +517,6 @@ void HAL_PWR_EnterSTANDBYMode(void) __WFI(); } -/** - * @brief This function handles the PWR PVD interrupt request. - * @note This API should be called under the PVD_IRQHandler(). - * @retval None - */ -void HAL_PWR_PVD_IRQHandler(void) -{ - /* Check PWR Exti flag */ - if (__HAL_PWR_PVD_EXTI_GET_FLAG() != RESET) - { - /* PWR PVD interrupt user callback */ - HAL_PWR_PVDCallback(); - /* Clear PWR Exti pending bit */ - __HAL_PWR_PVD_EXTI_CLEAR_FLAG(); - } -} - -/** - * @brief PWR PVD interrupt callback - * @retval None - */ -__weak void HAL_PWR_PVDCallback(void) -{ - /* NOTE : This function Should not be modified, when the callback is needed, - the HAL_PWR_PVDCallback could be implemented in the user file - */ -} /** * @brief Indicates Sleep-On-Exit when returning from Handler mode to Thread mode. @@ -512,6 +532,7 @@ void HAL_PWR_EnableSleepOnExit(void) SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPONEXIT_Msk)); } + /** * @brief Disables Sleep-On-Exit feature when returning from Handler mode to Thread mode. * @note Clears SLEEPONEXIT bit of SCR register. When this bit is set, the processor @@ -524,8 +545,9 @@ void HAL_PWR_DisableSleepOnExit(void) CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPONEXIT_Msk)); } + /** - * @brief Enables CORTEX M4 SEVONPEND bit. + * @brief Enables CORTEX M3 SEVONPEND bit. * @note Sets SEVONPEND bit of SCR register. When this bit is set, this causes * WFE to wake up when an interrupt moves from inactive to pended. * @retval None @@ -536,8 +558,9 @@ void HAL_PWR_EnableSEVOnPend(void) SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SEVONPEND_Msk)); } + /** - * @brief Disables CORTEX M4 SEVONPEND bit. + * @brief Disables CORTEX M3 SEVONPEND bit. * @note Clears SEVONPEND bit of SCR register. When this bit is set, this causes * WFE to wake up when an interrupt moves from inactive to pended. * @retval None @@ -548,6 +571,37 @@ void HAL_PWR_DisableSEVOnPend(void) CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SEVONPEND_Msk)); } + + +/** + * @brief This function handles the PWR PVD interrupt request. + * @note This API should be called under the PVD_IRQHandler(). + * @retval None + */ +void HAL_PWR_PVD_IRQHandler(void) +{ + /* Check PWR exti flag */ + if (__HAL_PWR_PVD_EXTI_GET_FLAG() != RESET) + { + /* PWR PVD interrupt user callback */ + HAL_PWR_PVDCallback(); + + /* Clear PWR Exti pending bit */ + __HAL_PWR_PVD_EXTI_CLEAR_FLAG(); + } +} + +/** + * @brief PWR PVD interrupt callback + * @retval None + */ +__weak void HAL_PWR_PVDCallback(void) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_PWR_PVDCallback could be implemented in the user file + */ +} + /** * @} */ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_rcc.c b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_rcc.c new file mode 100644 index 00000000..12b88c8a --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_rcc.c @@ -0,0 +1,1429 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_rcc.c + * @author MCD Application Team + * @brief RCC HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Reset and Clock Control (RCC) peripheral: + * + Initialization and de-initialization functions + * + Peripheral Control functions + * + @verbatim + ============================================================================== + ##### RCC specific features ##### + ============================================================================== + [..] + After reset the device is running from Internal High Speed oscillator + (HSI 8MHz) with Flash 0 wait state, Flash prefetch buffer is enabled, + and all peripherals are off except internal SRAM, Flash and JTAG. + (+) There is no prescaler on High speed (AHB) and Low speed (APB) buses; + all peripherals mapped on these buses are running at HSI speed. + (+) The clock for all peripherals is switched off, except the SRAM and FLASH. + (+) All GPIOs are in input floating state, except the JTAG pins which + are assigned to be used for debug purpose. + [..] Once the device started from reset, the user application has to: + (+) Configure the clock source to be used to drive the System clock + (if the application needs higher frequency/performance) + (+) Configure the System clock frequency and Flash settings + (+) Configure the AHB and APB buses prescalers + (+) Enable the clock for the peripheral(s) to be used + (+) Configure the clock source(s) for peripherals whose clocks are not + derived from the System clock (I2S, RTC, ADC, USB OTG FS) + + ##### RCC Limitations ##### + ============================================================================== + [..] + A delay between an RCC peripheral clock enable and the effective peripheral + enabling should be taken into account in order to manage the peripheral read/write + from/to registers. + (+) This delay depends on the peripheral mapping. + (++) AHB & APB peripherals, 1 dummy read is necessary + + [..] + Workarounds: + (#) For AHB & APB peripherals, a dummy read to the peripheral register has been + inserted in each __HAL_RCC_PPP_CLK_ENABLE() macro. + + @endverbatim + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @defgroup RCC RCC +* @brief RCC HAL module driver + * @{ + */ + +#ifdef HAL_RCC_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/** @defgroup RCC_Private_Constants RCC Private Constants + * @{ + */ +/** + * @} + */ +/* Private macro -------------------------------------------------------------*/ +/** @defgroup RCC_Private_Macros RCC Private Macros + * @{ + */ + +#define MCO1_CLK_ENABLE() __HAL_RCC_GPIOA_CLK_ENABLE() +#define MCO1_GPIO_PORT GPIOA +#define MCO1_PIN GPIO_PIN_8 + +/** + * @} + */ + +/* Private variables ---------------------------------------------------------*/ +/** @defgroup RCC_Private_Variables RCC Private Variables + * @{ + */ +/** + * @} + */ + +/* Private function prototypes -----------------------------------------------*/ +static void RCC_Delay(uint32_t mdelay); + +/* Exported functions --------------------------------------------------------*/ + +/** @defgroup RCC_Exported_Functions RCC Exported Functions + * @{ + */ + +/** @defgroup RCC_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * + @verbatim + =============================================================================== + ##### Initialization and de-initialization functions ##### + =============================================================================== + [..] + This section provides functions allowing to configure the internal/external oscillators + (HSE, HSI, LSE, LSI, PLL, CSS and MCO) and the System buses clocks (SYSCLK, AHB, APB1 + and APB2). + + [..] Internal/external clock and PLL configuration + (#) HSI (high-speed internal), 8 MHz factory-trimmed RC used directly or through + the PLL as System clock source. + (#) LSI (low-speed internal), ~40 KHz low consumption RC used as IWDG and/or RTC + clock source. + + (#) HSE (high-speed external), 4 to 24 MHz (STM32F100xx) or 4 to 16 MHz (STM32F101x/STM32F102x/STM32F103x) or 3 to 25 MHz (STM32F105x/STM32F107x) crystal oscillator used directly or + through the PLL as System clock source. Can be used also as RTC clock source. + + (#) LSE (low-speed external), 32 KHz oscillator used as RTC clock source. + + (#) PLL (clocked by HSI or HSE), featuring different output clocks: + (++) The first output is used to generate the high speed system clock (up to 72 MHz for STM32F10xxx or up to 24 MHz for STM32F100xx) + (++) The second output is used to generate the clock for the USB OTG FS (48 MHz) + + (#) CSS (Clock security system), once enable using the macro __HAL_RCC_CSS_ENABLE() + and if a HSE clock failure occurs(HSE used directly or through PLL as System + clock source), the System clocks automatically switched to HSI and an interrupt + is generated if enabled. The interrupt is linked to the Cortex-M3 NMI + (Non-Maskable Interrupt) exception vector. + + (#) MCO1 (microcontroller clock output), used to output SYSCLK, HSI, + HSE or PLL clock (divided by 2) on PA8 pin + PLL2CLK, PLL3CLK/2, PLL3CLK and XTI for STM32F105x/STM32F107x + + [..] System, AHB and APB buses clocks configuration + (#) Several clock sources can be used to drive the System clock (SYSCLK): HSI, + HSE and PLL. + The AHB clock (HCLK) is derived from System clock through configurable + prescaler and used to clock the CPU, memory and peripherals mapped + on AHB bus (DMA, GPIO...). APB1 (PCLK1) and APB2 (PCLK2) clocks are derived + from AHB clock through configurable prescalers and used to clock + the peripherals mapped on these buses. You can use + "@ref HAL_RCC_GetSysClockFreq()" function to retrieve the frequencies of these clocks. + + -@- All the peripheral clocks are derived from the System clock (SYSCLK) except: + (+@) RTC: RTC clock can be derived either from the LSI, LSE or HSE clock + divided by 128. + (+@) USB OTG FS and RTC: USB OTG FS require a frequency equal to 48 MHz + to work correctly. This clock is derived of the main PLL through PLL Multiplier. + (+@) I2S interface on STM32F105x/STM32F107x can be derived from PLL3CLK + (+@) IWDG clock which is always the LSI clock. + + (#) For STM32F10xxx, the maximum frequency of the SYSCLK and HCLK/PCLK2 is 72 MHz, PCLK1 36 MHz. + For STM32F100xx, the maximum frequency of the SYSCLK and HCLK/PCLK1/PCLK2 is 24 MHz. + Depending on the SYSCLK frequency, the flash latency should be adapted accordingly. + @endverbatim + * @{ + */ + +/* + Additional consideration on the SYSCLK based on Latency settings: + +-----------------------------------------------+ + | Latency | SYSCLK clock frequency (MHz) | + |---------------|-------------------------------| + |0WS(1CPU cycle)| 0 < SYSCLK <= 24 | + |---------------|-------------------------------| + |1WS(2CPU cycle)| 24 < SYSCLK <= 48 | + |---------------|-------------------------------| + |2WS(3CPU cycle)| 48 < SYSCLK <= 72 | + +-----------------------------------------------+ + */ + +/** + * @brief Resets the RCC clock configuration to the default reset state. + * @note The default reset state of the clock configuration is given below: + * - HSI ON and used as system clock source + * - HSE, PLL, PLL2 and PLL3 are OFF + * - AHB, APB1 and APB2 prescaler set to 1. + * - CSS and MCO1 OFF + * - All interrupts disabled + * - All flags are cleared + * @note This function does not modify the configuration of the + * - Peripheral clocks + * - LSI, LSE and RTC clocks + * @retval HAL_StatusTypeDef + */ +HAL_StatusTypeDef HAL_RCC_DeInit(void) +{ + uint32_t tickstart; + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Set HSION bit */ + SET_BIT(RCC->CR, RCC_CR_HSION); + + /* Wait till HSI is ready */ + while (READ_BIT(RCC->CR, RCC_CR_HSIRDY) == RESET) + { + if ((HAL_GetTick() - tickstart) > HSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Set HSITRIM bits to the reset value */ + MODIFY_REG(RCC->CR, RCC_CR_HSITRIM, (0x10U << RCC_CR_HSITRIM_Pos)); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Reset CFGR register */ + CLEAR_REG(RCC->CFGR); + + /* Wait till clock switch is ready */ + while (READ_BIT(RCC->CFGR, RCC_CFGR_SWS) != RESET) + { + if ((HAL_GetTick() - tickstart) > CLOCKSWITCH_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Update the SystemCoreClock global variable */ + SystemCoreClock = HSI_VALUE; + + /* Adapt Systick interrupt period */ + if (HAL_InitTick(uwTickPrio) != HAL_OK) + { + return HAL_ERROR; + } + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Second step is to clear PLLON bit */ + CLEAR_BIT(RCC->CR, RCC_CR_PLLON); + + /* Wait till PLL is disabled */ + while (READ_BIT(RCC->CR, RCC_CR_PLLRDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > PLL_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Ensure to reset PLLSRC and PLLMUL bits */ + CLEAR_REG(RCC->CFGR); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Reset HSEON & CSSON bits */ + CLEAR_BIT(RCC->CR, RCC_CR_HSEON | RCC_CR_CSSON); + + /* Wait till HSE is disabled */ + while (READ_BIT(RCC->CR, RCC_CR_HSERDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > HSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Reset HSEBYP bit */ + CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); + +#if defined(RCC_PLL2_SUPPORT) + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Clear PLL2ON bit */ + CLEAR_BIT(RCC->CR, RCC_CR_PLL2ON); + + /* Wait till PLL2 is disabled */ + while (READ_BIT(RCC->CR, RCC_CR_PLL2RDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > PLL2_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + +#endif /* RCC_PLL2_SUPPORT */ + +#if defined(RCC_PLLI2S_SUPPORT) + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Clear PLL3ON bit */ + CLEAR_BIT(RCC->CR, RCC_CR_PLL3ON); + + /* Wait till PLL3 is disabled */ + while (READ_BIT(RCC->CR, RCC_CR_PLL3RDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > PLLI2S_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + +#endif /* RCC_PLLI2S_SUPPORT */ + +#if defined(RCC_CFGR2_PREDIV1) + /* Reset CFGR2 register */ + CLEAR_REG(RCC->CFGR2); +#endif /* RCC_CFGR2_PREDIV1 */ + + /* Reset all CSR flags */ + SET_BIT(RCC->CSR, RCC_CSR_RMVF); + + /* Disable all interrupts */ + CLEAR_REG(RCC->CIR); + + return HAL_OK; +} + +/** + * @brief Initializes the RCC Oscillators according to the specified parameters in the + * RCC_OscInitTypeDef. + * @param RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that + * contains the configuration information for the RCC Oscillators. + * @note The PLL is not disabled when used as system clock. + * @note The PLL is not disabled when USB OTG FS clock is enabled (specific to devices with USB FS) + * @note Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not + * supported by this macro. User should request a transition to LSE Off + * first and then LSE On or LSE Bypass. + * @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not + * supported by this macro. User should request a transition to HSE Off + * first and then HSE On or HSE Bypass. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef* RCC_OscInitStruct) +{ + uint32_t tickstart; + uint32_t pll_config; + + /* Check Null pointer */ + if (RCC_OscInitStruct == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_RCC_OSCILLATORTYPE(RCC_OscInitStruct->OscillatorType)); + + /*------------------------------- HSE Configuration ------------------------*/ + if (((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) + { + /* Check the parameters */ + assert_param(IS_RCC_HSE(RCC_OscInitStruct->HSEState)); + + /* When the HSE is used as system clock or clock source for PLL in these cases it is not allowed to be disabled */ + if ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_HSE) + || ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && (__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSE))) + { + if ((__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) && (RCC_OscInitStruct->HSEState == RCC_HSE_OFF)) + { + return HAL_ERROR; + } + } + else + { + /* Set the new HSE configuration ---------------------------------------*/ + __HAL_RCC_HSE_CONFIG(RCC_OscInitStruct->HSEState); + + + /* Check the HSE State */ + if (RCC_OscInitStruct->HSEState != RCC_HSE_OFF) + { + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till HSE is ready */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) + { + if ((HAL_GetTick() - tickstart) > HSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till HSE is disabled */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > HSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + } + + /*----------------------------- HSI Configuration --------------------------*/ + if (((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) + { + /* Check the parameters */ + assert_param(IS_RCC_HSI(RCC_OscInitStruct->HSIState)); + assert_param(IS_RCC_CALIBRATION_VALUE(RCC_OscInitStruct->HSICalibrationValue)); + + /* Check if HSI is used as system clock or as PLL source when PLL is selected as system clock */ + if ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_HSI) + || ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && (__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSI_DIV2))) + { + /* When HSI is used as system clock it will not disabled */ + if ((__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) && (RCC_OscInitStruct->HSIState != RCC_HSI_ON)) + { + return HAL_ERROR; + } + /* Otherwise, just the calibration is allowed */ + else + { + /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ + __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); + } + } + else + { + /* Check the HSI State */ + if (RCC_OscInitStruct->HSIState != RCC_HSI_OFF) + { + /* Enable the Internal High Speed oscillator (HSI). */ + __HAL_RCC_HSI_ENABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till HSI is ready */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) + { + if ((HAL_GetTick() - tickstart) > HSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ + __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); + } + else + { + /* Disable the Internal High Speed oscillator (HSI). */ + __HAL_RCC_HSI_DISABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till HSI is disabled */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > HSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + } + + /*------------------------------ LSI Configuration -------------------------*/ + if (((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) + { + /* Check the parameters */ + assert_param(IS_RCC_LSI(RCC_OscInitStruct->LSIState)); + + /* Check the LSI State */ + if (RCC_OscInitStruct->LSIState != RCC_LSI_OFF) + { + /* Enable the Internal Low Speed oscillator (LSI). */ + __HAL_RCC_LSI_ENABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till LSI is ready */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) == RESET) + { + if ((HAL_GetTick() - tickstart) > LSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* To have a fully stabilized clock in the specified range, a software delay of 1ms + should be added.*/ + RCC_Delay(1); + } + else + { + /* Disable the Internal Low Speed oscillator (LSI). */ + __HAL_RCC_LSI_DISABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till LSI is disabled */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > LSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + + /*------------------------------ LSE Configuration -------------------------*/ + if (((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE) + { + FlagStatus pwrclkchanged = RESET; + + /* Check the parameters */ + assert_param(IS_RCC_LSE(RCC_OscInitStruct->LSEState)); + + /* Update LSE configuration in Backup Domain control register */ + /* Requires to enable write access to Backup Domain of necessary */ + if (__HAL_RCC_PWR_IS_CLK_DISABLED()) + { + __HAL_RCC_PWR_CLK_ENABLE(); + pwrclkchanged = SET; + } + + if (HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP)) + { + /* Enable write access to Backup domain */ + SET_BIT(PWR->CR, PWR_CR_DBP); + + /* Wait for Backup domain Write protection disable */ + tickstart = HAL_GetTick(); + + while (HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP)) + { + if ((HAL_GetTick() - tickstart) > RCC_DBP_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + + /* Set the new LSE configuration -----------------------------------------*/ + __HAL_RCC_LSE_CONFIG(RCC_OscInitStruct->LSEState); + + /* Check the LSE State */ + if (RCC_OscInitStruct->LSEState != RCC_LSE_OFF) + { + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till LSE is ready */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) + { + if ((HAL_GetTick() - tickstart) > RCC_LSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till LSE is disabled */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > RCC_LSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + + /* Require to disable power clock if necessary */ + if (pwrclkchanged == SET) + { + __HAL_RCC_PWR_CLK_DISABLE(); + } + } + +#if defined(RCC_CR_PLL2ON) + /*-------------------------------- PLL2 Configuration -----------------------*/ + /* Check the parameters */ + assert_param(IS_RCC_PLL2(RCC_OscInitStruct->PLL2.PLL2State)); + + if ((RCC_OscInitStruct->PLL2.PLL2State) != RCC_PLL2_NONE) + { + /* This bit can not be cleared if the PLL2 clock is used indirectly as system + clock (i.e. it is used as PLL clock entry that is used as system clock). */ + if ((__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSE) && \ + (__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && \ + ((READ_BIT(RCC->CFGR2, RCC_CFGR2_PREDIV1SRC)) == RCC_CFGR2_PREDIV1SRC_PLL2)) + { + return HAL_ERROR; + } + else + { + if ((RCC_OscInitStruct->PLL2.PLL2State) == RCC_PLL2_ON) + { + /* Check the parameters */ + assert_param(IS_RCC_PLL2_MUL(RCC_OscInitStruct->PLL2.PLL2MUL)); + assert_param(IS_RCC_HSE_PREDIV2(RCC_OscInitStruct->PLL2.HSEPrediv2Value)); + + /* Prediv2 can be written only when the PLLI2S is disabled. */ + /* Return an error only if new value is different from the programmed value */ + if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_PLL3ON) && \ + (__HAL_RCC_HSE_GET_PREDIV2() != RCC_OscInitStruct->PLL2.HSEPrediv2Value)) + { + return HAL_ERROR; + } + + /* Disable the main PLL2. */ + __HAL_RCC_PLL2_DISABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till PLL2 is disabled */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLL2RDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > PLL2_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Configure the HSE prediv2 factor --------------------------------*/ + __HAL_RCC_HSE_PREDIV2_CONFIG(RCC_OscInitStruct->PLL2.HSEPrediv2Value); + + /* Configure the main PLL2 multiplication factors. */ + __HAL_RCC_PLL2_CONFIG(RCC_OscInitStruct->PLL2.PLL2MUL); + + /* Enable the main PLL2. */ + __HAL_RCC_PLL2_ENABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till PLL2 is ready */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLL2RDY) == RESET) + { + if ((HAL_GetTick() - tickstart) > PLL2_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Set PREDIV1 source to HSE */ + CLEAR_BIT(RCC->CFGR2, RCC_CFGR2_PREDIV1SRC); + + /* Disable the main PLL2. */ + __HAL_RCC_PLL2_DISABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till PLL2 is disabled */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLL2RDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > PLL2_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + } + +#endif /* RCC_CR_PLL2ON */ + /*-------------------------------- PLL Configuration -----------------------*/ + /* Check the parameters */ + assert_param(IS_RCC_PLL(RCC_OscInitStruct->PLL.PLLState)); + + if ((RCC_OscInitStruct->PLL.PLLState) != RCC_PLL_NONE) + { + /* Check if the PLL is used as system clock or not */ + if (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_PLLCLK) + { + if ((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_ON) + { + /* Check the parameters */ + assert_param(IS_RCC_PLLSOURCE(RCC_OscInitStruct->PLL.PLLSource)); + assert_param(IS_RCC_PLL_MUL(RCC_OscInitStruct->PLL.PLLMUL)); + + /* Disable the main PLL. */ + __HAL_RCC_PLL_DISABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till PLL is disabled */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > PLL_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Configure the HSE prediv factor --------------------------------*/ + /* It can be written only when the PLL is disabled. Not used in PLL source is different than HSE */ + if (RCC_OscInitStruct->PLL.PLLSource == RCC_PLLSOURCE_HSE) + { + /* Check the parameter */ + assert_param(IS_RCC_HSE_PREDIV(RCC_OscInitStruct->HSEPredivValue)); +#if defined(RCC_CFGR2_PREDIV1SRC) + assert_param(IS_RCC_PREDIV1_SOURCE(RCC_OscInitStruct->Prediv1Source)); + + /* Set PREDIV1 source */ + SET_BIT(RCC->CFGR2, RCC_OscInitStruct->Prediv1Source); +#endif /* RCC_CFGR2_PREDIV1SRC */ + + /* Set PREDIV1 Value */ + __HAL_RCC_HSE_PREDIV_CONFIG(RCC_OscInitStruct->HSEPredivValue); + } + + /* Configure the main PLL clock source and multiplication factors. */ + __HAL_RCC_PLL_CONFIG(RCC_OscInitStruct->PLL.PLLSource, + RCC_OscInitStruct->PLL.PLLMUL); + /* Enable the main PLL. */ + __HAL_RCC_PLL_ENABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till PLL is ready */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) + { + if ((HAL_GetTick() - tickstart) > PLL_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Disable the main PLL. */ + __HAL_RCC_PLL_DISABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till PLL is disabled */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > PLL_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + else + { + /* Check if there is a request to disable the PLL used as System clock source */ + if ((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_OFF) + { + return HAL_ERROR; + } + else + { + /* Do not return HAL_ERROR if request repeats the current configuration */ + pll_config = RCC->CFGR; + + if ((READ_BIT(pll_config, RCC_CFGR_PLLSRC) != RCC_OscInitStruct->PLL.PLLSource) || + (READ_BIT(pll_config, RCC_CFGR_PLLMULL) != RCC_OscInitStruct->PLL.PLLMUL)) + { + return HAL_ERROR; + } + } + } + } + + return HAL_OK; +} + +/** + * @brief Initializes the CPU, AHB and APB buses clocks according to the specified + * parameters in the RCC_ClkInitStruct. + * @param RCC_ClkInitStruct pointer to an RCC_OscInitTypeDef structure that + * contains the configuration information for the RCC peripheral. + * @param FLatency FLASH Latency + * The value of this parameter depend on device used within the same series + * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency + * and updated by @ref HAL_RCC_GetHCLKFreq() function called within this function + * + * @note The HSI is used (enabled by hardware) as system clock source after + * start-up from Reset, wake-up from STOP and STANDBY mode, or in case + * of failure of the HSE used directly or indirectly as system clock + * (if the Clock Security System CSS is enabled). + * + * @note A switch from one clock source to another occurs only if the target + * clock source is ready (clock stable after start-up delay or PLL locked). + * If a clock source which is not yet ready is selected, the switch will + * occur when the clock source will be ready. + * You can use @ref HAL_RCC_GetClockConfig() function to know which clock is + * currently used as system clock source. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef* RCC_ClkInitStruct, uint32_t FLatency) +{ + uint32_t tickstart; + + /* Check Null pointer */ + if (RCC_ClkInitStruct == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_RCC_CLOCKTYPE(RCC_ClkInitStruct->ClockType)); + assert_param(IS_FLASH_LATENCY(FLatency)); + + /* To correctly read data from FLASH memory, the number of wait states (LATENCY) + must be correctly programmed according to the frequency of the CPU clock + (HCLK) of the device. */ + +#if defined(FLASH_ACR_LATENCY) + + /* Increasing the number of wait states because of higher CPU frequency */ + if (FLatency > __HAL_FLASH_GET_LATENCY()) + { + /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */ + __HAL_FLASH_SET_LATENCY(FLatency); + + /* Check that the new number of wait states is taken into account to access the Flash + memory by reading the FLASH_ACR register */ + if (__HAL_FLASH_GET_LATENCY() != FLatency) + { + return HAL_ERROR; + } + } + +#endif /* FLASH_ACR_LATENCY */ + + /*-------------------------- HCLK Configuration --------------------------*/ + if (((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK) + { + /* Set the highest APBx dividers in order to ensure that we do not go through + a non-spec phase whatever we decrease or increase HCLK. */ + if (((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1) + { + MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE1, RCC_HCLK_DIV16); + } + + if (((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2) + { + MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE2, (RCC_HCLK_DIV16 << 3)); + } + + /* Set the new HCLK clock divider */ + assert_param(IS_RCC_HCLK(RCC_ClkInitStruct->AHBCLKDivider)); + MODIFY_REG(RCC->CFGR, RCC_CFGR_HPRE, RCC_ClkInitStruct->AHBCLKDivider); + } + + /*------------------------- SYSCLK Configuration ---------------------------*/ + if (((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK) + { + assert_param(IS_RCC_SYSCLKSOURCE(RCC_ClkInitStruct->SYSCLKSource)); + + /* HSE is selected as System Clock Source */ + if (RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE) + { + /* Check the HSE ready flag */ + if (__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) + { + return HAL_ERROR; + } + } + /* PLL is selected as System Clock Source */ + else if (RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK) + { + /* Check the PLL ready flag */ + if (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) + { + return HAL_ERROR; + } + } + /* HSI is selected as System Clock Source */ + else + { + /* Check the HSI ready flag */ + if (__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) + { + return HAL_ERROR; + } + } + + __HAL_RCC_SYSCLK_CONFIG(RCC_ClkInitStruct->SYSCLKSource); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + while (__HAL_RCC_GET_SYSCLK_SOURCE() != (RCC_ClkInitStruct->SYSCLKSource << RCC_CFGR_SWS_Pos)) + { + if ((HAL_GetTick() - tickstart) > CLOCKSWITCH_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + +#if defined(FLASH_ACR_LATENCY) + + /* Decreasing the number of wait states because of lower CPU frequency */ + if (FLatency < __HAL_FLASH_GET_LATENCY()) + { + /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */ + __HAL_FLASH_SET_LATENCY(FLatency); + + /* Check that the new number of wait states is taken into account to access the Flash + memory by reading the FLASH_ACR register */ + if (__HAL_FLASH_GET_LATENCY() != FLatency) + { + return HAL_ERROR; + } + } + +#endif /* FLASH_ACR_LATENCY */ + + /*-------------------------- PCLK1 Configuration ---------------------------*/ + if (((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1) + { + assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB1CLKDivider)); + MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE1, RCC_ClkInitStruct->APB1CLKDivider); + } + + /*-------------------------- PCLK2 Configuration ---------------------------*/ + if (((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2) + { + assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB2CLKDivider)); + MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE2, ((RCC_ClkInitStruct->APB2CLKDivider) << 3)); + } + + /* Update the SystemCoreClock global variable */ + SystemCoreClock = HAL_RCC_GetSysClockFreq() >> AHBPrescTable[(RCC->CFGR & RCC_CFGR_HPRE) >> RCC_CFGR_HPRE_Pos]; + + /* Configure the source of time base considering new system clocks settings*/ + HAL_InitTick(uwTickPrio); + + return HAL_OK; +} + +/** + * @} + */ + +/** @defgroup RCC_Exported_Functions_Group2 Peripheral Control functions + * @brief RCC clocks control functions + * + @verbatim + =============================================================================== + ##### Peripheral Control functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to control the RCC Clocks + frequencies. + + @endverbatim + * @{ + */ + +/** + * @brief Selects the clock source to output on MCO pin. + * @note MCO pin should be configured in alternate function mode. + * @param RCC_MCOx specifies the output direction for the clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_MCO1 Clock source to output on MCO1 pin(PA8). + * @param RCC_MCOSource specifies the clock source to output. + * This parameter can be one of the following values: + * @arg @ref RCC_MCO1SOURCE_NOCLOCK No clock selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_SYSCLK System clock selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_HSI HSI selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_HSE HSE selected as MCO clock + @if STM32F105xC + * @arg @ref RCC_MCO1SOURCE_PLLCLK PLL clock divided by 2 selected as MCO source + * @arg @ref RCC_MCO1SOURCE_PLL2CLK PLL2 clock selected as MCO source + * @arg @ref RCC_MCO1SOURCE_PLL3CLK_DIV2 PLL3 clock divided by 2 selected as MCO source + * @arg @ref RCC_MCO1SOURCE_EXT_HSE XT1 external 3-25 MHz oscillator clock selected as MCO source + * @arg @ref RCC_MCO1SOURCE_PLL3CLK PLL3 clock selected as MCO source + @endif + @if STM32F107xC + * @arg @ref RCC_MCO1SOURCE_PLLCLK PLL clock divided by 2 selected as MCO source + * @arg @ref RCC_MCO1SOURCE_PLL2CLK PLL2 clock selected as MCO source + * @arg @ref RCC_MCO1SOURCE_PLL3CLK_DIV2 PLL3 clock divided by 2 selected as MCO source + * @arg @ref RCC_MCO1SOURCE_EXT_HSE XT1 external 3-25 MHz oscillator clock selected as MCO source + * @arg @ref RCC_MCO1SOURCE_PLL3CLK PLL3 clock selected as MCO source + @endif + * @param RCC_MCODiv specifies the MCO DIV. + * This parameter can be one of the following values: + * @arg @ref RCC_MCODIV_1 no division applied to MCO clock + * @retval None + */ +void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv) +{ + GPIO_InitTypeDef gpio = {0U}; + + /* Check the parameters */ + assert_param(IS_RCC_MCO(RCC_MCOx)); + assert_param(IS_RCC_MCODIV(RCC_MCODiv)); + assert_param(IS_RCC_MCO1SOURCE(RCC_MCOSource)); + + /* Prevent unused argument(s) compilation warning */ + UNUSED(RCC_MCOx); + UNUSED(RCC_MCODiv); + + /* Configure the MCO1 pin in alternate function mode */ + gpio.Mode = GPIO_MODE_AF_PP; + gpio.Speed = GPIO_SPEED_FREQ_HIGH; + gpio.Pull = GPIO_NOPULL; + gpio.Pin = MCO1_PIN; + + /* MCO1 Clock Enable */ + MCO1_CLK_ENABLE(); + + HAL_GPIO_Init(MCO1_GPIO_PORT, &gpio); + + /* Configure the MCO clock source */ + __HAL_RCC_MCO1_CONFIG(RCC_MCOSource, RCC_MCODiv); +} + +/** + * @brief Enables the Clock Security System. + * @note If a failure is detected on the HSE oscillator clock, this oscillator + * is automatically disabled and an interrupt is generated to inform the + * software about the failure (Clock Security System Interrupt, CSSI), + * allowing the MCU to perform rescue operations. The CSSI is linked to + * the Cortex-M3 NMI (Non-Maskable Interrupt) exception vector. + * @retval None + */ +void HAL_RCC_EnableCSS(void) +{ + *(__IO uint32_t*) RCC_CR_CSSON_BB = (uint32_t)ENABLE; +} + +/** + * @brief Disables the Clock Security System. + * @retval None + */ +void HAL_RCC_DisableCSS(void) +{ + *(__IO uint32_t*) RCC_CR_CSSON_BB = (uint32_t)DISABLE; +} + +/** + * @brief Returns the SYSCLK frequency + * @note The system frequency computed by this function is not the real + * frequency in the chip. It is calculated based on the predefined + * constant and the selected clock source: + * @note If SYSCLK source is HSI, function returns values based on HSI_VALUE(*) + * @note If SYSCLK source is HSE, function returns a value based on HSE_VALUE + * divided by PREDIV factor(**) + * @note If SYSCLK source is PLL, function returns a value based on HSE_VALUE + * divided by PREDIV factor(**) or HSI_VALUE(*) multiplied by the PLL factor. + * @note (*) HSI_VALUE is a constant defined in stm32f1xx_hal_conf.h file (default value + * 8 MHz) but the real value may vary depending on the variations + * in voltage and temperature. + * @note (**) HSE_VALUE is a constant defined in stm32f1xx_hal_conf.h file (default value + * 8 MHz), user has to ensure that HSE_VALUE is same as the real + * frequency of the crystal used. Otherwise, this function may + * have wrong result. + * + * @note The result of this function could be not correct when using fractional + * value for HSE crystal. + * + * @note This function can be used by the user application to compute the + * baud-rate for the communication peripherals or configure other parameters. + * + * @note Each time SYSCLK changes, this function must be called to update the + * right SYSCLK value. Otherwise, any configuration based on this function will be incorrect. + * + * @retval SYSCLK frequency + */ +uint32_t HAL_RCC_GetSysClockFreq(void) +{ +#if defined(RCC_CFGR2_PREDIV1SRC) + const uint8_t aPLLMULFactorTable[14] = {0, 0, 4, 5, 6, 7, 8, 9, 0, 0, 0, 0, 0, 13}; + const uint8_t aPredivFactorTable[16] = {1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16}; +#else + const uint8_t aPLLMULFactorTable[16] = {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 16}; +#if defined(RCC_CFGR2_PREDIV1) + const uint8_t aPredivFactorTable[16] = {1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16}; +#else + const uint8_t aPredivFactorTable[2] = {1, 2}; +#endif /*RCC_CFGR2_PREDIV1*/ + +#endif + uint32_t tmpreg = 0U, prediv = 0U, pllclk = 0U, pllmul = 0U; + uint32_t sysclockfreq = 0U; +#if defined(RCC_CFGR2_PREDIV1SRC) + uint32_t prediv2 = 0U, pll2mul = 0U; +#endif /*RCC_CFGR2_PREDIV1SRC*/ + + tmpreg = RCC->CFGR; + + /* Get SYSCLK source -------------------------------------------------------*/ + switch (tmpreg & RCC_CFGR_SWS) + { + case RCC_SYSCLKSOURCE_STATUS_HSE: /* HSE used as system clock */ + { + sysclockfreq = HSE_VALUE; + break; + } + + case RCC_SYSCLKSOURCE_STATUS_PLLCLK: /* PLL used as system clock */ + { + pllmul = aPLLMULFactorTable[(uint32_t)(tmpreg & RCC_CFGR_PLLMULL) >> RCC_CFGR_PLLMULL_Pos]; + + if ((tmpreg & RCC_CFGR_PLLSRC) != RCC_PLLSOURCE_HSI_DIV2) + { +#if defined(RCC_CFGR2_PREDIV1) + prediv = aPredivFactorTable[(uint32_t)(RCC->CFGR2 & RCC_CFGR2_PREDIV1) >> RCC_CFGR2_PREDIV1_Pos]; +#else + prediv = aPredivFactorTable[(uint32_t)(RCC->CFGR & RCC_CFGR_PLLXTPRE) >> RCC_CFGR_PLLXTPRE_Pos]; +#endif /*RCC_CFGR2_PREDIV1*/ +#if defined(RCC_CFGR2_PREDIV1SRC) + + if (HAL_IS_BIT_SET(RCC->CFGR2, RCC_CFGR2_PREDIV1SRC)) + { + /* PLL2 selected as Prediv1 source */ + /* PLLCLK = PLL2CLK / PREDIV1 * PLLMUL with PLL2CLK = HSE/PREDIV2 * PLL2MUL */ + prediv2 = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> RCC_CFGR2_PREDIV2_Pos) + 1; + pll2mul = ((RCC->CFGR2 & RCC_CFGR2_PLL2MUL) >> RCC_CFGR2_PLL2MUL_Pos) + 2; + pllclk = (uint32_t)(((uint64_t)HSE_VALUE * (uint64_t)pll2mul * (uint64_t)pllmul) / ((uint64_t)prediv2 * (uint64_t)prediv)); + } + else + { + /* HSE used as PLL clock source : PLLCLK = HSE/PREDIV1 * PLLMUL */ + pllclk = (uint32_t)((HSE_VALUE * pllmul) / prediv); + } + + /* If PLLMUL was set to 13 means that it was to cover the case PLLMUL 6.5 (avoid using float) */ + /* In this case need to divide pllclk by 2 */ + if (pllmul == aPLLMULFactorTable[(uint32_t)(RCC_CFGR_PLLMULL6_5) >> RCC_CFGR_PLLMULL_Pos]) + { + pllclk = pllclk / 2; + } + +#else + /* HSE used as PLL clock source : PLLCLK = HSE/PREDIV1 * PLLMUL */ + pllclk = (uint32_t)((HSE_VALUE * pllmul) / prediv); +#endif /*RCC_CFGR2_PREDIV1SRC*/ + } + else + { + /* HSI used as PLL clock source : PLLCLK = HSI/2 * PLLMUL */ + pllclk = (uint32_t)((HSI_VALUE >> 1) * pllmul); + } + + sysclockfreq = pllclk; + break; + } + + case RCC_SYSCLKSOURCE_STATUS_HSI: /* HSI used as system clock source */ + default: /* HSI used as system clock */ + { + sysclockfreq = HSI_VALUE; + break; + } + } + + return sysclockfreq; +} + +/** + * @brief Returns the HCLK frequency + * @note Each time HCLK changes, this function must be called to update the + * right HCLK value. Otherwise, any configuration based on this function will be incorrect. + * + * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency + * and updated within this function + * @retval HCLK frequency + */ +uint32_t HAL_RCC_GetHCLKFreq(void) +{ + return SystemCoreClock; +} + +/** + * @brief Returns the PCLK1 frequency + * @note Each time PCLK1 changes, this function must be called to update the + * right PCLK1 value. Otherwise, any configuration based on this function will be incorrect. + * @retval PCLK1 frequency + */ +uint32_t HAL_RCC_GetPCLK1Freq(void) +{ + /* Get HCLK source and Compute PCLK1 frequency ---------------------------*/ + return (HAL_RCC_GetHCLKFreq() >> APBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE1) >> RCC_CFGR_PPRE1_Pos]); +} + +/** + * @brief Returns the PCLK2 frequency + * @note Each time PCLK2 changes, this function must be called to update the + * right PCLK2 value. Otherwise, any configuration based on this function will be incorrect. + * @retval PCLK2 frequency + */ +uint32_t HAL_RCC_GetPCLK2Freq(void) +{ + /* Get HCLK source and Compute PCLK2 frequency ---------------------------*/ + return (HAL_RCC_GetHCLKFreq() >> APBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE2) >> RCC_CFGR_PPRE2_Pos]); +} + +/** + * @brief Configures the RCC_OscInitStruct according to the internal + * RCC configuration registers. + * @param RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that + * will be configured. + * @retval None + */ +void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef* RCC_OscInitStruct) +{ + /* Check the parameters */ + assert_param(RCC_OscInitStruct != NULL); + + /* Set all possible values for the Oscillator type parameter ---------------*/ + RCC_OscInitStruct->OscillatorType = RCC_OSCILLATORTYPE_HSE | RCC_OSCILLATORTYPE_HSI \ + | RCC_OSCILLATORTYPE_LSE | RCC_OSCILLATORTYPE_LSI; + +#if defined(RCC_CFGR2_PREDIV1SRC) + /* Get the Prediv1 source --------------------------------------------------*/ + RCC_OscInitStruct->Prediv1Source = READ_BIT(RCC->CFGR2, RCC_CFGR2_PREDIV1SRC); +#endif /* RCC_CFGR2_PREDIV1SRC */ + + /* Get the HSE configuration -----------------------------------------------*/ + if ((RCC->CR & RCC_CR_HSEBYP) == RCC_CR_HSEBYP) + { + RCC_OscInitStruct->HSEState = RCC_HSE_BYPASS; + } + else if ((RCC->CR & RCC_CR_HSEON) == RCC_CR_HSEON) + { + RCC_OscInitStruct->HSEState = RCC_HSE_ON; + } + else + { + RCC_OscInitStruct->HSEState = RCC_HSE_OFF; + } + + RCC_OscInitStruct->HSEPredivValue = __HAL_RCC_HSE_GET_PREDIV(); + + /* Get the HSI configuration -----------------------------------------------*/ + if ((RCC->CR & RCC_CR_HSION) == RCC_CR_HSION) + { + RCC_OscInitStruct->HSIState = RCC_HSI_ON; + } + else + { + RCC_OscInitStruct->HSIState = RCC_HSI_OFF; + } + + RCC_OscInitStruct->HSICalibrationValue = (uint32_t)((RCC->CR & RCC_CR_HSITRIM) >> RCC_CR_HSITRIM_Pos); + + /* Get the LSE configuration -----------------------------------------------*/ + if ((RCC->BDCR & RCC_BDCR_LSEBYP) == RCC_BDCR_LSEBYP) + { + RCC_OscInitStruct->LSEState = RCC_LSE_BYPASS; + } + else if ((RCC->BDCR & RCC_BDCR_LSEON) == RCC_BDCR_LSEON) + { + RCC_OscInitStruct->LSEState = RCC_LSE_ON; + } + else + { + RCC_OscInitStruct->LSEState = RCC_LSE_OFF; + } + + /* Get the LSI configuration -----------------------------------------------*/ + if ((RCC->CSR & RCC_CSR_LSION) == RCC_CSR_LSION) + { + RCC_OscInitStruct->LSIState = RCC_LSI_ON; + } + else + { + RCC_OscInitStruct->LSIState = RCC_LSI_OFF; + } + + + /* Get the PLL configuration -----------------------------------------------*/ + if ((RCC->CR & RCC_CR_PLLON) == RCC_CR_PLLON) + { + RCC_OscInitStruct->PLL.PLLState = RCC_PLL_ON; + } + else + { + RCC_OscInitStruct->PLL.PLLState = RCC_PLL_OFF; + } + + RCC_OscInitStruct->PLL.PLLSource = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLSRC); + RCC_OscInitStruct->PLL.PLLMUL = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLMULL); +#if defined(RCC_CR_PLL2ON) + + /* Get the PLL2 configuration -----------------------------------------------*/ + if ((RCC->CR & RCC_CR_PLL2ON) == RCC_CR_PLL2ON) + { + RCC_OscInitStruct->PLL2.PLL2State = RCC_PLL2_ON; + } + else + { + RCC_OscInitStruct->PLL2.PLL2State = RCC_PLL2_OFF; + } + + RCC_OscInitStruct->PLL2.HSEPrediv2Value = __HAL_RCC_HSE_GET_PREDIV2(); + RCC_OscInitStruct->PLL2.PLL2MUL = (uint32_t)(RCC->CFGR2 & RCC_CFGR2_PLL2MUL); +#endif /* RCC_CR_PLL2ON */ +} + +/** + * @brief Get the RCC_ClkInitStruct according to the internal + * RCC configuration registers. + * @param RCC_ClkInitStruct pointer to an RCC_ClkInitTypeDef structure that + * contains the current clock configuration. + * @param pFLatency Pointer on the Flash Latency. + * @retval None + */ +void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef* RCC_ClkInitStruct, uint32_t* pFLatency) +{ + /* Check the parameters */ + assert_param(RCC_ClkInitStruct != NULL); + assert_param(pFLatency != NULL); + + /* Set all possible values for the Clock type parameter --------------------*/ + RCC_ClkInitStruct->ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2; + + /* Get the SYSCLK configuration --------------------------------------------*/ + RCC_ClkInitStruct->SYSCLKSource = (uint32_t)(RCC->CFGR & RCC_CFGR_SW); + + /* Get the HCLK configuration ----------------------------------------------*/ + RCC_ClkInitStruct->AHBCLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_HPRE); + + /* Get the APB1 configuration ----------------------------------------------*/ + RCC_ClkInitStruct->APB1CLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_PPRE1); + + /* Get the APB2 configuration ----------------------------------------------*/ + RCC_ClkInitStruct->APB2CLKDivider = (uint32_t)((RCC->CFGR & RCC_CFGR_PPRE2) >> 3); + +#if defined(FLASH_ACR_LATENCY) + /* Get the Flash Wait State (Latency) configuration ------------------------*/ + *pFLatency = (uint32_t)(FLASH->ACR & FLASH_ACR_LATENCY); +#else + /* For VALUE lines devices, only LATENCY_0 can be set*/ + *pFLatency = (uint32_t)FLASH_LATENCY_0; +#endif +} + +/** + * @brief This function handles the RCC CSS interrupt request. + * @note This API should be called under the NMI_Handler(). + * @retval None + */ +void HAL_RCC_NMI_IRQHandler(void) +{ + /* Check RCC CSSF flag */ + if (__HAL_RCC_GET_IT(RCC_IT_CSS)) + { + /* RCC Clock Security System interrupt user callback */ + HAL_RCC_CSSCallback(); + + /* Clear RCC CSS pending bit */ + __HAL_RCC_CLEAR_IT(RCC_IT_CSS); + } +} + +/** + * @brief This function provides delay (in milliseconds) based on CPU cycles method. + * @param mdelay: specifies the delay time length, in milliseconds. + * @retval None + */ +static void RCC_Delay(uint32_t mdelay) +{ + __IO uint32_t Delay = mdelay * (SystemCoreClock / 8U / 1000U); + + do + { + __NOP(); + } + while (Delay --); +} + +/** + * @brief RCC Clock Security System interrupt callback + * @retval none + */ +__weak void HAL_RCC_CSSCallback(void) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_RCC_CSSCallback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_RCC_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_rcc_ex.c b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_rcc_ex.c new file mode 100644 index 00000000..c200f952 --- /dev/null +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_rcc_ex.c @@ -0,0 +1,893 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_rcc_ex.c + * @author MCD Application Team + * @brief Extended RCC HAL module driver. + * This file provides firmware functions to manage the following + * functionalities RCC extension peripheral: + * + Extended Peripheral Control functions + * + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +#ifdef HAL_RCC_MODULE_ENABLED + +/** @defgroup RCCEx RCCEx + * @brief RCC Extension HAL module driver. + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/** @defgroup RCCEx_Private_Constants RCCEx Private Constants + * @{ + */ +/** + * @} + */ + +/* Private macro -------------------------------------------------------------*/ +/** @defgroup RCCEx_Private_Macros RCCEx Private Macros + * @{ + */ +/** + * @} + */ + +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup RCCEx_Exported_Functions RCCEx Exported Functions + * @{ + */ + +/** @defgroup RCCEx_Exported_Functions_Group1 Peripheral Control functions + * @brief Extended Peripheral Control functions + * +@verbatim + =============================================================================== + ##### Extended Peripheral Control functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to control the RCC Clocks + frequencies. + [..] + (@) Important note: Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to + select the RTC clock source; in this case the Backup domain will be reset in + order to modify the RTC Clock source, as consequence RTC registers (including + the backup registers) are set to their reset values. + +@endverbatim + * @{ + */ + +/** + * @brief Initializes the RCC extended peripherals clocks according to the specified parameters in the + * RCC_PeriphCLKInitTypeDef. + * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that + * contains the configuration information for the Extended Peripherals clocks(RTC clock). + * + * @note Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select + * the RTC clock source; in this case the Backup domain will be reset in + * order to modify the RTC Clock source, as consequence RTC registers (including + * the backup registers) are set to their reset values. + * + * @note In case of STM32F105xC or STM32F107xC devices, PLLI2S will be enabled if requested on + * one of 2 I2S interfaces. When PLLI2S is enabled, you need to call HAL_RCCEx_DisablePLLI2S to + * manually disable it. + * + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit) +{ + uint32_t tickstart = 0U, temp_reg = 0U; +#if defined(STM32F105xC) || defined(STM32F107xC) + uint32_t pllactive = 0U; +#endif /* STM32F105xC || STM32F107xC */ + + /* Check the parameters */ + assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection)); + + /*------------------------------- RTC/LCD Configuration ------------------------*/ + if ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == RCC_PERIPHCLK_RTC)) + { + /* check for RTC Parameters used to output RTCCLK */ + assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection)); + + FlagStatus pwrclkchanged = RESET; + + /* As soon as function is called to change RTC clock source, activation of the + power domain is done. */ + /* Requires to enable write access to Backup Domain of necessary */ + if (__HAL_RCC_PWR_IS_CLK_DISABLED()) + { + __HAL_RCC_PWR_CLK_ENABLE(); + pwrclkchanged = SET; + } + + if (HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP)) + { + /* Enable write access to Backup domain */ + SET_BIT(PWR->CR, PWR_CR_DBP); + + /* Wait for Backup domain Write protection disable */ + tickstart = HAL_GetTick(); + + while (HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP)) + { + if ((HAL_GetTick() - tickstart) > RCC_DBP_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + + /* Reset the Backup domain only if the RTC Clock source selection is modified from reset value */ + temp_reg = (RCC->BDCR & RCC_BDCR_RTCSEL); + + if ((temp_reg != 0x00000000U) && (temp_reg != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL))) + { + /* Store the content of BDCR register before the reset of Backup Domain */ + temp_reg = (RCC->BDCR & ~(RCC_BDCR_RTCSEL)); + /* RTC Clock selection can be changed only if the Backup Domain is reset */ + __HAL_RCC_BACKUPRESET_FORCE(); + __HAL_RCC_BACKUPRESET_RELEASE(); + /* Restore the Content of BDCR register */ + RCC->BDCR = temp_reg; + + /* Wait for LSERDY if LSE was enabled */ + if (HAL_IS_BIT_SET(temp_reg, RCC_BDCR_LSEON)) + { + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till LSE is ready */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) + { + if ((HAL_GetTick() - tickstart) > RCC_LSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + + __HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection); + + /* Require to disable power clock if necessary */ + if (pwrclkchanged == SET) + { + __HAL_RCC_PWR_CLK_DISABLE(); + } + } + + /*------------------------------ ADC clock Configuration ------------------*/ + if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_ADC) == RCC_PERIPHCLK_ADC) + { + /* Check the parameters */ + assert_param(IS_RCC_ADCPLLCLK_DIV(PeriphClkInit->AdcClockSelection)); + + /* Configure the ADC clock source */ + __HAL_RCC_ADC_CONFIG(PeriphClkInit->AdcClockSelection); + } + +#if defined(STM32F105xC) || defined(STM32F107xC) + + /*------------------------------ I2S2 Configuration ------------------------*/ + if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S2) == RCC_PERIPHCLK_I2S2) + { + /* Check the parameters */ + assert_param(IS_RCC_I2S2CLKSOURCE(PeriphClkInit->I2s2ClockSelection)); + + /* Configure the I2S2 clock source */ + __HAL_RCC_I2S2_CONFIG(PeriphClkInit->I2s2ClockSelection); + } + + /*------------------------------ I2S3 Configuration ------------------------*/ + if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S3) == RCC_PERIPHCLK_I2S3) + { + /* Check the parameters */ + assert_param(IS_RCC_I2S3CLKSOURCE(PeriphClkInit->I2s3ClockSelection)); + + /* Configure the I2S3 clock source */ + __HAL_RCC_I2S3_CONFIG(PeriphClkInit->I2s3ClockSelection); + } + + /*------------------------------ PLL I2S Configuration ----------------------*/ + /* Check that PLLI2S need to be enabled */ + if (HAL_IS_BIT_SET(RCC->CFGR2, RCC_CFGR2_I2S2SRC) || HAL_IS_BIT_SET(RCC->CFGR2, RCC_CFGR2_I2S3SRC)) + { + /* Update flag to indicate that PLL I2S should be active */ + pllactive = 1; + } + + /* Check if PLL I2S need to be enabled */ + if (pllactive == 1) + { + /* Enable PLL I2S only if not active */ + if (HAL_IS_BIT_CLR(RCC->CR, RCC_CR_PLL3ON)) + { + /* Check the parameters */ + assert_param(IS_RCC_PLLI2S_MUL(PeriphClkInit->PLLI2S.PLLI2SMUL)); + assert_param(IS_RCC_HSE_PREDIV2(PeriphClkInit->PLLI2S.HSEPrediv2Value)); + + /* Prediv2 can be written only when the PLL2 is disabled. */ + /* Return an error only if new value is different from the programmed value */ + if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_PLL2ON) && \ + (__HAL_RCC_HSE_GET_PREDIV2() != PeriphClkInit->PLLI2S.HSEPrediv2Value)) + { + return HAL_ERROR; + } + + /* Configure the HSE prediv2 factor --------------------------------*/ + __HAL_RCC_HSE_PREDIV2_CONFIG(PeriphClkInit->PLLI2S.HSEPrediv2Value); + + /* Configure the main PLLI2S multiplication factors. */ + __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SMUL); + + /* Enable the main PLLI2S. */ + __HAL_RCC_PLLI2S_ENABLE(); + + /* Get Start Tick*/ + tickstart = HAL_GetTick(); + + /* Wait till PLLI2S is ready */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET) + { + if ((HAL_GetTick() - tickstart) > PLLI2S_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Return an error only if user wants to change the PLLI2SMUL whereas PLLI2S is active */ + if (READ_BIT(RCC->CFGR2, RCC_CFGR2_PLL3MUL) != PeriphClkInit->PLLI2S.PLLI2SMUL) + { + return HAL_ERROR; + } + } + } + +#endif /* STM32F105xC || STM32F107xC */ + +#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6)\ + || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG)\ + || defined(STM32F105xC) || defined(STM32F107xC) + + /*------------------------------ USB clock Configuration ------------------*/ + if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_USB) == RCC_PERIPHCLK_USB) + { + /* Check the parameters */ + assert_param(IS_RCC_USBPLLCLK_DIV(PeriphClkInit->UsbClockSelection)); + + /* Configure the USB clock source */ + __HAL_RCC_USB_CONFIG(PeriphClkInit->UsbClockSelection); + } + +#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */ + + return HAL_OK; +} + +/** + * @brief Get the PeriphClkInit according to the internal + * RCC configuration registers. + * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that + * returns the configuration information for the Extended Peripherals clocks(RTC, I2S, ADC clocks). + * @retval None + */ +void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit) +{ + uint32_t srcclk = 0U; + + /* Set all possible values for the extended clock type parameter------------*/ + PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_RTC; + + /* Get the RTC configuration -----------------------------------------------*/ + srcclk = __HAL_RCC_GET_RTC_SOURCE(); + /* Source clock is LSE or LSI*/ + PeriphClkInit->RTCClockSelection = srcclk; + + /* Get the ADC clock configuration -----------------------------------------*/ + PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_ADC; + PeriphClkInit->AdcClockSelection = __HAL_RCC_GET_ADC_SOURCE(); + +#if defined(STM32F105xC) || defined(STM32F107xC) + /* Get the I2S2 clock configuration -----------------------------------------*/ + PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_I2S2; + PeriphClkInit->I2s2ClockSelection = __HAL_RCC_GET_I2S2_SOURCE(); + + /* Get the I2S3 clock configuration -----------------------------------------*/ + PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_I2S3; + PeriphClkInit->I2s3ClockSelection = __HAL_RCC_GET_I2S3_SOURCE(); + +#endif /* STM32F105xC || STM32F107xC */ + +#if defined(STM32F103xE) || defined(STM32F103xG) + /* Get the I2S2 clock configuration -----------------------------------------*/ + PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_I2S2; + PeriphClkInit->I2s2ClockSelection = RCC_I2S2CLKSOURCE_SYSCLK; + + /* Get the I2S3 clock configuration -----------------------------------------*/ + PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_I2S3; + PeriphClkInit->I2s3ClockSelection = RCC_I2S3CLKSOURCE_SYSCLK; + +#endif /* STM32F103xE || STM32F103xG */ + +#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6)\ + || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG)\ + || defined(STM32F105xC) || defined(STM32F107xC) + /* Get the USB clock configuration -----------------------------------------*/ + PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_USB; + PeriphClkInit->UsbClockSelection = __HAL_RCC_GET_USB_SOURCE(); +#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */ +} + +/** + * @brief Returns the peripheral clock frequency + * @note Returns 0 if peripheral clock is unknown + * @param PeriphClk Peripheral clock identifier + * This parameter can be one of the following values: + * @arg @ref RCC_PERIPHCLK_RTC RTC peripheral clock + * @arg @ref RCC_PERIPHCLK_ADC ADC peripheral clock + @if STM32F103xE + * @arg @ref RCC_PERIPHCLK_I2S2 I2S2 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S3 I2S3 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S3 I2S3 peripheral clock + @endif + @if STM32F103xG + * @arg @ref RCC_PERIPHCLK_I2S2 I2S2 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S3 I2S3 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S3 I2S3 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S2 I2S2 peripheral clock + @endif + @if STM32F105xC + * @arg @ref RCC_PERIPHCLK_I2S2 I2S2 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S3 I2S3 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S3 I2S3 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S2 I2S2 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S3 I2S3 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S3 I2S3 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S2 I2S2 peripheral clock + * @arg @ref RCC_PERIPHCLK_USB USB peripheral clock + @endif + @if STM32F107xC + * @arg @ref RCC_PERIPHCLK_I2S2 I2S2 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S3 I2S3 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S3 I2S3 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S2 I2S2 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S3 I2S3 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S3 I2S3 peripheral clock + * @arg @ref RCC_PERIPHCLK_I2S2 I2S2 peripheral clock + * @arg @ref RCC_PERIPHCLK_USB USB peripheral clock + @endif + @if STM32F102xx + * @arg @ref RCC_PERIPHCLK_USB USB peripheral clock + @endif + @if STM32F103xx + * @arg @ref RCC_PERIPHCLK_USB USB peripheral clock + @endif + * @retval Frequency in Hz (0: means that no available frequency for the peripheral) + */ +uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk) +{ +#if defined(STM32F105xC) || defined(STM32F107xC) + const uint8_t aPLLMULFactorTable[14] = {0, 0, 4, 5, 6, 7, 8, 9, 0, 0, 0, 0, 0, 13}; + const uint8_t aPredivFactorTable[16] = {1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16}; + + uint32_t prediv1 = 0U, pllclk = 0U, pllmul = 0U; + uint32_t pll2mul = 0U, pll3mul = 0U, prediv2 = 0U; +#endif /* STM32F105xC || STM32F107xC */ +#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6) || \ + defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG) + const uint8_t aPLLMULFactorTable[16] = {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 16}; + const uint8_t aPredivFactorTable[2] = {1, 2}; + + uint32_t prediv1 = 0U, pllclk = 0U, pllmul = 0U; +#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG */ + uint32_t temp_reg = 0U, frequency = 0U; + + /* Check the parameters */ + assert_param(IS_RCC_PERIPHCLOCK(PeriphClk)); + + switch (PeriphClk) + { +#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6)\ + || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG)\ + || defined(STM32F105xC) || defined(STM32F107xC) + + case RCC_PERIPHCLK_USB: + { + /* Get RCC configuration ------------------------------------------------------*/ + temp_reg = RCC->CFGR; + + /* Check if PLL is enabled */ + if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_PLLON)) + { + pllmul = aPLLMULFactorTable[(uint32_t)(temp_reg & RCC_CFGR_PLLMULL) >> RCC_CFGR_PLLMULL_Pos]; + + if ((temp_reg & RCC_CFGR_PLLSRC) != RCC_PLLSOURCE_HSI_DIV2) + { +#if defined(STM32F105xC) || defined(STM32F107xC) || defined(STM32F100xB)\ + || defined(STM32F100xE) + prediv1 = aPredivFactorTable[(uint32_t)(RCC->CFGR2 & RCC_CFGR2_PREDIV1) >> RCC_CFGR2_PREDIV1_Pos]; +#else + prediv1 = aPredivFactorTable[(uint32_t)(RCC->CFGR & RCC_CFGR_PLLXTPRE) >> RCC_CFGR_PLLXTPRE_Pos]; +#endif /* STM32F105xC || STM32F107xC || STM32F100xB || STM32F100xE */ + +#if defined(STM32F105xC) || defined(STM32F107xC) + + if (HAL_IS_BIT_SET(RCC->CFGR2, RCC_CFGR2_PREDIV1SRC)) + { + /* PLL2 selected as Prediv1 source */ + /* PLLCLK = PLL2CLK / PREDIV1 * PLLMUL with PLL2CLK = HSE/PREDIV2 * PLL2MUL */ + prediv2 = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> RCC_CFGR2_PREDIV2_Pos) + 1; + pll2mul = ((RCC->CFGR2 & RCC_CFGR2_PLL2MUL) >> RCC_CFGR2_PLL2MUL_Pos) + 2; + pllclk = (uint32_t)((((HSE_VALUE / prediv2) * pll2mul) / prediv1) * pllmul); + } + else + { + /* HSE used as PLL clock source : PLLCLK = HSE/PREDIV1 * PLLMUL */ + pllclk = (uint32_t)((HSE_VALUE / prediv1) * pllmul); + } + + /* If PLLMUL was set to 13 means that it was to cover the case PLLMUL 6.5 (avoid using float) */ + /* In this case need to divide pllclk by 2 */ + if (pllmul == aPLLMULFactorTable[(uint32_t)(RCC_CFGR_PLLMULL6_5) >> RCC_CFGR_PLLMULL_Pos]) + { + pllclk = pllclk / 2; + } + +#else + + if ((temp_reg & RCC_CFGR_PLLSRC) != RCC_PLLSOURCE_HSI_DIV2) + { + /* HSE used as PLL clock source : PLLCLK = HSE/PREDIV1 * PLLMUL */ + pllclk = (uint32_t)((HSE_VALUE / prediv1) * pllmul); + } + +#endif /* STM32F105xC || STM32F107xC */ + } + else + { + /* HSI used as PLL clock source : PLLCLK = HSI/2 * PLLMUL */ + pllclk = (uint32_t)((HSI_VALUE >> 1) * pllmul); + } + + /* Calcul of the USB frequency*/ +#if defined(STM32F105xC) || defined(STM32F107xC) + + /* USBCLK = PLLVCO = (2 x PLLCLK) / USB prescaler */ + if (__HAL_RCC_GET_USB_SOURCE() == RCC_USBCLKSOURCE_PLL_DIV2) + { + /* Prescaler of 2 selected for USB */ + frequency = pllclk; + } + else + { + /* Prescaler of 3 selected for USB */ + frequency = (2 * pllclk) / 3; + } + +#else + + /* USBCLK = PLLCLK / USB prescaler */ + if (__HAL_RCC_GET_USB_SOURCE() == RCC_USBCLKSOURCE_PLL) + { + /* No prescaler selected for USB */ + frequency = pllclk; + } + else + { + /* Prescaler of 1.5 selected for USB */ + frequency = (pllclk * 2) / 3; + } + +#endif + } + + break; + } + +#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */ +#if defined(STM32F103xE) || defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC) + + case RCC_PERIPHCLK_I2S2: + { +#if defined(STM32F103xE) || defined(STM32F103xG) + /* SYSCLK used as source clock for I2S2 */ + frequency = HAL_RCC_GetSysClockFreq(); +#else + + if (__HAL_RCC_GET_I2S2_SOURCE() == RCC_I2S2CLKSOURCE_SYSCLK) + { + /* SYSCLK used as source clock for I2S2 */ + frequency = HAL_RCC_GetSysClockFreq(); + } + else + { + /* Check if PLLI2S is enabled */ + if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_PLL3ON)) + { + /* PLLI2SVCO = 2 * PLLI2SCLK = 2 * (HSE/PREDIV2 * PLL3MUL) */ + prediv2 = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> RCC_CFGR2_PREDIV2_Pos) + 1; + pll3mul = ((RCC->CFGR2 & RCC_CFGR2_PLL3MUL) >> RCC_CFGR2_PLL3MUL_Pos) + 2; + frequency = (uint32_t)(2 * ((HSE_VALUE / prediv2) * pll3mul)); + } + } + +#endif /* STM32F103xE || STM32F103xG */ + break; + } + + case RCC_PERIPHCLK_I2S3: + { +#if defined(STM32F103xE) || defined(STM32F103xG) + /* SYSCLK used as source clock for I2S3 */ + frequency = HAL_RCC_GetSysClockFreq(); +#else + + if (__HAL_RCC_GET_I2S3_SOURCE() == RCC_I2S3CLKSOURCE_SYSCLK) + { + /* SYSCLK used as source clock for I2S3 */ + frequency = HAL_RCC_GetSysClockFreq(); + } + else + { + /* Check if PLLI2S is enabled */ + if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_PLL3ON)) + { + /* PLLI2SVCO = 2 * PLLI2SCLK = 2 * (HSE/PREDIV2 * PLL3MUL) */ + prediv2 = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> RCC_CFGR2_PREDIV2_Pos) + 1; + pll3mul = ((RCC->CFGR2 & RCC_CFGR2_PLL3MUL) >> RCC_CFGR2_PLL3MUL_Pos) + 2; + frequency = (uint32_t)(2 * ((HSE_VALUE / prediv2) * pll3mul)); + } + } + +#endif /* STM32F103xE || STM32F103xG */ + break; + } + +#endif /* STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */ + + case RCC_PERIPHCLK_RTC: + { + /* Get RCC BDCR configuration ------------------------------------------------------*/ + temp_reg = RCC->BDCR; + + /* Check if LSE is ready if RTC clock selection is LSE */ + if (((temp_reg & RCC_BDCR_RTCSEL) == RCC_RTCCLKSOURCE_LSE) && (HAL_IS_BIT_SET(temp_reg, RCC_BDCR_LSERDY))) + { + frequency = LSE_VALUE; + } + /* Check if LSI is ready if RTC clock selection is LSI */ + else if (((temp_reg & RCC_BDCR_RTCSEL) == RCC_RTCCLKSOURCE_LSI) && (HAL_IS_BIT_SET(RCC->CSR, RCC_CSR_LSIRDY))) + { + frequency = LSI_VALUE; + } + else if (((temp_reg & RCC_BDCR_RTCSEL) == RCC_RTCCLKSOURCE_HSE_DIV128) && (HAL_IS_BIT_SET(RCC->CR, RCC_CR_HSERDY))) + { + frequency = HSE_VALUE / 128U; + } + /* Clock not enabled for RTC*/ + else + { + /* nothing to do: frequency already initialized to 0U */ + } + + break; + } + + case RCC_PERIPHCLK_ADC: + { + frequency = HAL_RCC_GetPCLK2Freq() / (((__HAL_RCC_GET_ADC_SOURCE() >> RCC_CFGR_ADCPRE_Pos) + 1) * 2); + break; + } + + default: + { + break; + } + } + + return (frequency); +} + +/** + * @} + */ + +#if defined(STM32F105xC) || defined(STM32F107xC) +/** @defgroup RCCEx_Exported_Functions_Group2 PLLI2S Management function + * @brief PLLI2S Management functions + * +@verbatim + =============================================================================== + ##### Extended PLLI2S Management functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to control the PLLI2S + activation or deactivation +@endverbatim + * @{ + */ + +/** + * @brief Enable PLLI2S + * @param PLLI2SInit pointer to an RCC_PLLI2SInitTypeDef structure that + * contains the configuration information for the PLLI2S + * @note The PLLI2S configuration not modified if used by I2S2 or I2S3 Interface. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RCCEx_EnablePLLI2S(RCC_PLLI2SInitTypeDef* PLLI2SInit) +{ + uint32_t tickstart = 0U; + + /* Check that PLL I2S has not been already enabled by I2S2 or I2S3*/ + if (HAL_IS_BIT_CLR(RCC->CFGR2, RCC_CFGR2_I2S2SRC) && HAL_IS_BIT_CLR(RCC->CFGR2, RCC_CFGR2_I2S3SRC)) + { + /* Check the parameters */ + assert_param(IS_RCC_PLLI2S_MUL(PLLI2SInit->PLLI2SMUL)); + assert_param(IS_RCC_HSE_PREDIV2(PLLI2SInit->HSEPrediv2Value)); + + /* Prediv2 can be written only when the PLL2 is disabled. */ + /* Return an error only if new value is different from the programmed value */ + if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_PLL2ON) && \ + (__HAL_RCC_HSE_GET_PREDIV2() != PLLI2SInit->HSEPrediv2Value)) + { + return HAL_ERROR; + } + + /* Disable the main PLLI2S. */ + __HAL_RCC_PLLI2S_DISABLE(); + + /* Get Start Tick*/ + tickstart = HAL_GetTick(); + + /* Wait till PLLI2S is ready */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > PLLI2S_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Configure the HSE prediv2 factor --------------------------------*/ + __HAL_RCC_HSE_PREDIV2_CONFIG(PLLI2SInit->HSEPrediv2Value); + + + /* Configure the main PLLI2S multiplication factors. */ + __HAL_RCC_PLLI2S_CONFIG(PLLI2SInit->PLLI2SMUL); + + /* Enable the main PLLI2S. */ + __HAL_RCC_PLLI2S_ENABLE(); + + /* Get Start Tick*/ + tickstart = HAL_GetTick(); + + /* Wait till PLLI2S is ready */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET) + { + if ((HAL_GetTick() - tickstart) > PLLI2S_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* PLLI2S cannot be modified as already used by I2S2 or I2S3 */ + return HAL_ERROR; + } + + return HAL_OK; +} + +/** + * @brief Disable PLLI2S + * @note PLLI2S is not disabled if used by I2S2 or I2S3 Interface. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RCCEx_DisablePLLI2S(void) +{ + uint32_t tickstart = 0U; + + /* Disable PLL I2S as not requested by I2S2 or I2S3*/ + if (HAL_IS_BIT_CLR(RCC->CFGR2, RCC_CFGR2_I2S2SRC) && HAL_IS_BIT_CLR(RCC->CFGR2, RCC_CFGR2_I2S3SRC)) + { + /* Disable the main PLLI2S. */ + __HAL_RCC_PLLI2S_DISABLE(); + + /* Get Start Tick*/ + tickstart = HAL_GetTick(); + + /* Wait till PLLI2S is ready */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > PLLI2S_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* PLLI2S is currently used by I2S2 or I2S3. Cannot be disabled.*/ + return HAL_ERROR; + } + + return HAL_OK; +} + +/** + * @} + */ + +/** @defgroup RCCEx_Exported_Functions_Group3 PLL2 Management function + * @brief PLL2 Management functions + * +@verbatim + =============================================================================== + ##### Extended PLL2 Management functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to control the PLL2 + activation or deactivation +@endverbatim + * @{ + */ + +/** + * @brief Enable PLL2 + * @param PLL2Init pointer to an RCC_PLL2InitTypeDef structure that + * contains the configuration information for the PLL2 + * @note The PLL2 configuration not modified if used indirectly as system clock. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RCCEx_EnablePLL2(RCC_PLL2InitTypeDef* PLL2Init) +{ + uint32_t tickstart = 0U; + + /* This bit can not be cleared if the PLL2 clock is used indirectly as system + clock (i.e. it is used as PLL clock entry that is used as system clock). */ + if ((__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSE) && \ + (__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && \ + ((READ_BIT(RCC->CFGR2, RCC_CFGR2_PREDIV1SRC)) == RCC_CFGR2_PREDIV1SRC_PLL2)) + { + return HAL_ERROR; + } + else + { + /* Check the parameters */ + assert_param(IS_RCC_PLL2_MUL(PLL2Init->PLL2MUL)); + assert_param(IS_RCC_HSE_PREDIV2(PLL2Init->HSEPrediv2Value)); + + /* Prediv2 can be written only when the PLLI2S is disabled. */ + /* Return an error only if new value is different from the programmed value */ + if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_PLL3ON) && \ + (__HAL_RCC_HSE_GET_PREDIV2() != PLL2Init->HSEPrediv2Value)) + { + return HAL_ERROR; + } + + /* Disable the main PLL2. */ + __HAL_RCC_PLL2_DISABLE(); + + /* Get Start Tick*/ + tickstart = HAL_GetTick(); + + /* Wait till PLL2 is disabled */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLL2RDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > PLL2_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Configure the HSE prediv2 factor --------------------------------*/ + __HAL_RCC_HSE_PREDIV2_CONFIG(PLL2Init->HSEPrediv2Value); + + /* Configure the main PLL2 multiplication factors. */ + __HAL_RCC_PLL2_CONFIG(PLL2Init->PLL2MUL); + + /* Enable the main PLL2. */ + __HAL_RCC_PLL2_ENABLE(); + + /* Get Start Tick*/ + tickstart = HAL_GetTick(); + + /* Wait till PLL2 is ready */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLL2RDY) == RESET) + { + if ((HAL_GetTick() - tickstart) > PLL2_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + + return HAL_OK; +} + +/** + * @brief Disable PLL2 + * @note PLL2 is not disabled if used indirectly as system clock. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RCCEx_DisablePLL2(void) +{ + uint32_t tickstart = 0U; + + /* This bit can not be cleared if the PLL2 clock is used indirectly as system + clock (i.e. it is used as PLL clock entry that is used as system clock). */ + if ((__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSE) && \ + (__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && \ + ((READ_BIT(RCC->CFGR2, RCC_CFGR2_PREDIV1SRC)) == RCC_CFGR2_PREDIV1SRC_PLL2)) + { + return HAL_ERROR; + } + else + { + /* Disable the main PLL2. */ + __HAL_RCC_PLL2_DISABLE(); + + /* Get Start Tick*/ + tickstart = HAL_GetTick(); + + /* Wait till PLL2 is disabled */ + while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLL2RDY) != RESET) + { + if ((HAL_GetTick() - tickstart) > PLL2_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + + return HAL_OK; +} + +/** + * @} + */ +#endif /* STM32F105xC || STM32F107xC */ + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_RCC_MODULE_ENABLED */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ + diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim.c b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_tim.c similarity index 57% rename from EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim.c rename to EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_tim.c index 081beb08..184c8c22 100644 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim.c +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_tim.c @@ -1,36 +1,34 @@ /** ****************************************************************************** - * @file stm32f4xx_hal_tim.c + * @file stm32f1xx_hal_tim.c * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 * @brief TIM HAL module driver. * This file provides firmware functions to manage the following * functionalities of the Timer (TIM) peripheral: - * + Time Base Initialization - * + Time Base Start - * + Time Base Start Interruption - * + Time Base Start DMA - * + Time Output Compare/PWM Initialization - * + Time Output Compare/PWM Channel Configuration - * + Time Output Compare/PWM Start - * + Time Output Compare/PWM Start Interruption - * + Time Output Compare/PWM Start DMA - * + Time Input Capture Initialization - * + Time Input Capture Channel Configuration - * + Time Input Capture Start - * + Time Input Capture Start Interruption - * + Time Input Capture Start DMA - * + Time One Pulse Initialization - * + Time One Pulse Channel Configuration - * + Time One Pulse Start - * + Time Encoder Interface Initialization - * + Time Encoder Interface Start - * + Time Encoder Interface Start Interruption - * + Time Encoder Interface Start DMA + * + TIM Time Base Initialization + * + TIM Time Base Start + * + TIM Time Base Start Interruption + * + TIM Time Base Start DMA + * + TIM Output Compare/PWM Initialization + * + TIM Output Compare/PWM Channel Configuration + * + TIM Output Compare/PWM Start + * + TIM Output Compare/PWM Start Interruption + * + TIM Output Compare/PWM Start DMA + * + TIM Input Capture Initialization + * + TIM Input Capture Channel Configuration + * + TIM Input Capture Start + * + TIM Input Capture Start Interruption + * + TIM Input Capture Start DMA + * + TIM One Pulse Initialization + * + TIM One Pulse Channel Configuration + * + TIM One Pulse Start + * + TIM Encoder Interface Initialization + * + TIM Encoder Interface Start + * + TIM Encoder Interface Start Interruption + * + TIM Encoder Interface Start DMA * + Commutation Event configuration with Interruption and DMA - * + Time OCRef clear configuration - * + Time External Clock configuration + * + TIM OCRef clear configuration + * + TIM External Clock configuration @verbatim ============================================================================== ##### TIMER Generic features ##### @@ -44,12 +42,15 @@ (++) Output Compare (++) PWM generation (Edge and Center-aligned Mode) (++) One-pulse mode output + (#) Synchronization circuit to control the timer with external signals and to interconnect + several timers together. + (#) Supports incremental encoder for positioning purposes - ##### How to use this driver ##### + ##### How to use this driver ##### ============================================================================== [..] (#) Initialize the TIM low level resources by implementing the following functions - depending from feature used : + depending on the selected feature: (++) Time Base : HAL_TIM_Base_MspInit() (++) Input Capture : HAL_TIM_IC_MspInit() (++) Output Compare : HAL_TIM_OC_MspInit() @@ -58,10 +59,10 @@ (++) Encoder mode output : HAL_TIM_Encoder_MspInit() (#) Initialize the TIM low level resources : - (##) Enable the TIM interface clock using __TIMx_CLK_ENABLE(); + (##) Enable the TIM interface clock using __HAL_RCC_TIMx_CLK_ENABLE(); (##) TIM pins configuration (+++) Enable the clock for the TIM GPIOs using the following function: - __GPIOx_CLK_ENABLE(); + __HAL_RCC_GPIOx_CLK_ENABLE(); (+++) Configure these TIM pins in Alternate function mode using HAL_GPIO_Init(); (#) The external Clock can be configured, if needed (the default clock is the @@ -70,17 +71,17 @@ any start function. (#) Configure the TIM in the desired functioning mode using one of the - initialization function of this driver: - (++) HAL_TIM_Base_Init: to use the Timer to generate a simple time base - (++) HAL_TIM_OC_Init and HAL_TIM_OC_ConfigChannel: to use the Timer to generate an - Output Compare signal. - (++) HAL_TIM_PWM_Init and HAL_TIM_PWM_ConfigChannel: to use the Timer to generate a - PWM signal. - (++) HAL_TIM_IC_Init and HAL_TIM_IC_ConfigChannel: to use the Timer to measure an - external signal. - (++) HAL_TIM_OnePulse_Init and HAL_TIM_OnePulse_ConfigChannel: to use the Timer - in One Pulse Mode. - (++) HAL_TIM_Encoder_Init: to use the Timer Encoder Interface. + Initialization function of this driver: + (++) HAL_TIM_Base_Init: to use the Timer to generate a simple time base + (++) HAL_TIM_OC_Init and HAL_TIM_OC_ConfigChannel: to use the Timer to generate an + Output Compare signal. + (++) HAL_TIM_PWM_Init and HAL_TIM_PWM_ConfigChannel: to use the Timer to generate a + PWM signal. + (++) HAL_TIM_IC_Init and HAL_TIM_IC_ConfigChannel: to use the Timer to measure an + external signal. + (++) HAL_TIM_OnePulse_Init and HAL_TIM_OnePulse_ConfigChannel: to use the Timer + in One Pulse Mode. + (++) HAL_TIM_Encoder_Init: to use the Timer Encoder Interface. (#) Activate the TIM peripheral using one of the start functions depending from the feature used: (++) Time Base : HAL_TIM_Base_Start(), HAL_TIM_Base_Start_DMA(), HAL_TIM_Base_Start_IT() @@ -94,41 +95,97 @@ HAL_TIM_DMABurst_WriteStart() HAL_TIM_DMABurst_ReadStart() + *** Callback registration *** + ============================================= + + [..] + The compilation define USE_HAL_TIM_REGISTER_CALLBACKS when set to 1 + allows the user to configure dynamically the driver callbacks. + + [..] + Use Function @ref HAL_TIM_RegisterCallback() to register a callback. + @ref HAL_TIM_RegisterCallback() takes as parameters the HAL peripheral handle, + the Callback ID and a pointer to the user callback function. + + [..] + Use function @ref HAL_TIM_UnRegisterCallback() to reset a callback to the default + weak function. + @ref HAL_TIM_UnRegisterCallback takes as parameters the HAL peripheral handle, + and the Callback ID. + + [..] + These functions allow to register/unregister following callbacks: + (+) Base_MspInitCallback : TIM Base Msp Init Callback. + (+) Base_MspDeInitCallback : TIM Base Msp DeInit Callback. + (+) IC_MspInitCallback : TIM IC Msp Init Callback. + (+) IC_MspDeInitCallback : TIM IC Msp DeInit Callback. + (+) OC_MspInitCallback : TIM OC Msp Init Callback. + (+) OC_MspDeInitCallback : TIM OC Msp DeInit Callback. + (+) PWM_MspInitCallback : TIM PWM Msp Init Callback. + (+) PWM_MspDeInitCallback : TIM PWM Msp DeInit Callback. + (+) OnePulse_MspInitCallback : TIM One Pulse Msp Init Callback. + (+) OnePulse_MspDeInitCallback : TIM One Pulse Msp DeInit Callback. + (+) Encoder_MspInitCallback : TIM Encoder Msp Init Callback. + (+) Encoder_MspDeInitCallback : TIM Encoder Msp DeInit Callback. + (+) HallSensor_MspInitCallback : TIM Hall Sensor Msp Init Callback. + (+) HallSensor_MspDeInitCallback : TIM Hall Sensor Msp DeInit Callback. + (+) PeriodElapsedCallback : TIM Period Elapsed Callback. + (+) PeriodElapsedHalfCpltCallback : TIM Period Elapsed half complete Callback. + (+) TriggerCallback : TIM Trigger Callback. + (+) TriggerHalfCpltCallback : TIM Trigger half complete Callback. + (+) IC_CaptureCallback : TIM Input Capture Callback. + (+) IC_CaptureHalfCpltCallback : TIM Input Capture half complete Callback. + (+) OC_DelayElapsedCallback : TIM Output Compare Delay Elapsed Callback. + (+) PWM_PulseFinishedCallback : TIM PWM Pulse Finished Callback. + (+) PWM_PulseFinishedHalfCpltCallback : TIM PWM Pulse Finished half complete Callback. + (+) ErrorCallback : TIM Error Callback. + (+) CommutationCallback : TIM Commutation Callback. + (+) CommutationHalfCpltCallback : TIM Commutation half complete Callback. + (+) BreakCallback : TIM Break Callback. + + [..] +By default, after the Init and when the state is HAL_TIM_STATE_RESET +all interrupt callbacks are set to the corresponding weak functions: + examples @ref HAL_TIM_TriggerCallback(), @ref HAL_TIM_ErrorCallback(). + + [..] + Exception done for MspInit and MspDeInit functions that are reset to the legacy weak + functionalities in the Init / DeInit only when these callbacks are null + (not registered beforehand). If not, MspInit or MspDeInit are not null, the Init / DeInit + keep and use the user MspInit / MspDeInit callbacks(registered beforehand) + + [..] + Callbacks can be registered / unregistered in HAL_TIM_STATE_READY state only. + Exception done MspInit / MspDeInit that can be registered / unregistered + in HAL_TIM_STATE_READY or HAL_TIM_STATE_RESET state, + thus registered(user) MspInit / DeInit callbacks can be used during the Init / DeInit. + In that case first register the MspInit/MspDeInit user callbacks + using @ref HAL_TIM_RegisterCallback() before calling DeInit or Init function. + + [..] + When The compilation define USE_HAL_TIM_REGISTER_CALLBACKS is set to 0 or + not defined, the callback registration feature is not available and all callbacks + are set to the corresponding weak functions. + @endverbatim ****************************************************************************** * @attention * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

* - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause * ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" +#include "stm32f1xx_hal.h" -/** @addtogroup STM32F4xx_HAL_Driver +/** @addtogroup STM32F1xx_HAL_Driver * @{ */ @@ -143,14 +200,13 @@ /* Private define ------------------------------------------------------------*/ /* Private macro -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ /** @addtogroup TIM_Private_Functions * @{ */ -/* Private function prototypes -----------------------------------------------*/ static void TIM_OC1_SetConfig(TIM_TypeDef* TIMx, TIM_OC_InitTypeDef* OC_Config); static void TIM_OC3_SetConfig(TIM_TypeDef* TIMx, TIM_OC_InitTypeDef* OC_Config); static void TIM_OC4_SetConfig(TIM_TypeDef* TIMx, TIM_OC_InitTypeDef* OC_Config); - static void TIM_TI1_ConfigInputStage(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter); static void TIM_TI2_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter); @@ -159,27 +215,25 @@ static void TIM_TI3_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32 uint32_t TIM_ICFilter); static void TIM_TI4_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter); - -static void TIM_ETR_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ExtTRGPrescaler, - uint32_t TIM_ExtTRGPolarity, uint32_t ExtTRGFilter); - -static void TIM_ITRx_SetConfig(TIM_TypeDef* TIMx, uint16_t TIM_ITRx); +static void TIM_ITRx_SetConfig(TIM_TypeDef* TIMx, uint32_t InputTriggerSource); static void TIM_DMAPeriodElapsedCplt(DMA_HandleTypeDef* hdma); +static void TIM_DMAPeriodElapsedHalfCplt(DMA_HandleTypeDef* hdma); static void TIM_DMATriggerCplt(DMA_HandleTypeDef* hdma); -static void TIM_SlaveTimer_SetConfig(TIM_HandleTypeDef* htim, - TIM_SlaveConfigTypeDef* sSlaveConfig); +static void TIM_DMATriggerHalfCplt(DMA_HandleTypeDef* hdma); +static HAL_StatusTypeDef TIM_SlaveTimer_SetConfig(TIM_HandleTypeDef* htim, + TIM_SlaveConfigTypeDef* sSlaveConfig); /** * @} */ - /* Exported functions --------------------------------------------------------*/ + /** @defgroup TIM_Exported_Functions TIM Exported Functions * @{ */ -/** @defgroup TIM_Exported_Functions_Group1 Time Base functions - * @brief Time Base functions - * +/** @defgroup TIM_Exported_Functions_Group1 TIM Time Base functions + * @brief Time Base functions + * @verbatim ============================================================================== ##### Time Base functions ##### @@ -200,9 +254,12 @@ static void TIM_SlaveTimer_SetConfig(TIM_HandleTypeDef* htim, */ /** * @brief Initializes the TIM Time base Unit according to the specified - * parameters in the TIM_HandleTypeDef and create the associated handle. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * parameters in the TIM_HandleTypeDef and initialize the associated handle. + * @note Switching from Center Aligned counter mode to Edge counter mode (or reverse) + * requires a timer reset to avoid unexpected direction + * due to DIR bit readonly in center aligned mode. + * Ex: call @ref HAL_TIM_Base_DeInit() before HAL_TIM_Base_Init() + * @param htim TIM Base handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Init(TIM_HandleTypeDef* htim) @@ -217,138 +274,194 @@ HAL_StatusTypeDef HAL_TIM_Base_Init(TIM_HandleTypeDef* htim) assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); + assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload)); if (htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + /* Reset interrupt callbacks to legacy weak callbacks */ + TIM_ResetCallback(htim); + + if (htim->Base_MspInitCallback == NULL) + { + htim->Base_MspInitCallback = HAL_TIM_Base_MspInit; + } + + /* Init the low level hardware : GPIO, CLOCK, NVIC */ + htim->Base_MspInitCallback(htim); +#else /* Init the low level hardware : GPIO, CLOCK, NVIC */ HAL_TIM_Base_MspInit(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } /* Set the TIM state */ htim->State = HAL_TIM_STATE_BUSY; + /* Set the Time Base configuration */ TIM_Base_SetConfig(htim->Instance, &htim->Init); + /* Initialize the TIM state*/ htim->State = HAL_TIM_STATE_READY; + return HAL_OK; } /** * @brief DeInitializes the TIM Base peripheral - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Base handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_DeInit(TIM_HandleTypeDef* htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); + htim->State = HAL_TIM_STATE_BUSY; + /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + + if (htim->Base_MspDeInitCallback == NULL) + { + htim->Base_MspDeInitCallback = HAL_TIM_Base_MspDeInit; + } + + /* DeInit the low level hardware */ + htim->Base_MspDeInitCallback(htim); +#else /* DeInit the low level hardware: GPIO, CLOCK, NVIC */ HAL_TIM_Base_MspDeInit(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; + /* Release Lock */ __HAL_UNLOCK(htim); + return HAL_OK; } /** * @brief Initializes the TIM Base MSP. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Base handle * @retval None */ __weak void HAL_TIM_Base_MspInit(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, + + /* NOTE : This function should not be modified, when the callback is needed, the HAL_TIM_Base_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM Base MSP. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Base handle * @retval None */ __weak void HAL_TIM_Base_MspDeInit(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, + + /* NOTE : This function should not be modified, when the callback is needed, the HAL_TIM_Base_MspDeInit could be implemented in the user file */ } + /** * @brief Starts the TIM Base generation. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Base handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Start(TIM_HandleTypeDef* htim) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); + /* Set the TIM state */ htim->State = HAL_TIM_STATE_BUSY; - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Change the TIM state*/ htim->State = HAL_TIM_STATE_READY; + /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Base generation. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Base handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Stop(TIM_HandleTypeDef* htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); + /* Set the TIM state */ htim->State = HAL_TIM_STATE_BUSY; + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Change the TIM state*/ htim->State = HAL_TIM_STATE_READY; + /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Base generation in interrupt mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Base handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Start_IT(TIM_HandleTypeDef* htim) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); + /* Enable the TIM Update interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_UPDATE); - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Base generation in interrupt mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Base handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Stop_IT(TIM_HandleTypeDef* htim) @@ -357,32 +470,35 @@ HAL_StatusTypeDef HAL_TIM_Base_Stop_IT(TIM_HandleTypeDef* htim) assert_param(IS_TIM_INSTANCE(htim->Instance)); /* Disable the TIM Update interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_UPDATE); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Base generation in DMA mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param pData: The source Buffer address. - * @param Length: The length of data to be transferred from memory to peripheral. + * @param htim TIM Base handle + * @param pData The source Buffer address. + * @param Length The length of data to be transferred from memory to peripheral. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Start_DMA(TIM_HandleTypeDef* htim, uint32_t* pData, uint16_t Length) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_DMA_INSTANCE(htim->Instance)); - if ((htim->State == HAL_TIM_STATE_BUSY)) + if (htim->State == HAL_TIM_STATE_BUSY) { return HAL_BUSY; } - else if ((htim->State == HAL_TIM_STATE_READY)) + else if (htim->State == HAL_TIM_STATE_READY) { - if ((pData == 0U) && (Length > 0U)) + if ((pData == NULL) && (Length > 0U)) { return HAL_ERROR; } @@ -391,70 +507,97 @@ HAL_StatusTypeDef HAL_TIM_Base_Start_DMA(TIM_HandleTypeDef* htim, uint32_t* pDat htim->State = HAL_TIM_STATE_BUSY; } } + else + { + /* nothing to do */ + } - /* Set the DMA Period elapsed callback */ + /* Set the DMA Period elapsed callbacks */ htim->hdma[TIM_DMA_ID_UPDATE]->XferCpltCallback = TIM_DMAPeriodElapsedCplt; + htim->hdma[TIM_DMA_ID_UPDATE]->XferHalfCpltCallback = TIM_DMAPeriodElapsedHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_UPDATE]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)pData, (uint32_t)&htim->Instance->ARR, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)pData, (uint32_t)&htim->Instance->ARR, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Update DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_UPDATE); - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Base generation in DMA mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Base handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Stop_DMA(TIM_HandleTypeDef* htim) { /* Check the parameters */ assert_param(IS_TIM_DMA_INSTANCE(htim->Instance)); + /* Disable the TIM Update DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_UPDATE); + + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_UPDATE]); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; + /* Return function status */ return HAL_OK; } + /** * @} */ -/** @defgroup TIM_Exported_Functions_Group2 Time Output Compare functions - * @brief Time Output Compare functions - * +/** @defgroup TIM_Exported_Functions_Group2 TIM Output Compare functions + * @brief TIM Output Compare functions + * @verbatim ============================================================================== - ##### Time Output Compare functions ##### + ##### TIM Output Compare functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM Output Compare. (+) De-initialize the TIM Output Compare. - (+) Start the Time Output Compare. - (+) Stop the Time Output Compare. - (+) Start the Time Output Compare and enable interrupt. - (+) Stop the Time Output Compare and disable interrupt. - (+) Start the Time Output Compare and enable DMA transfer. - (+) Stop the Time Output Compare and disable DMA transfer. + (+) Start the TIM Output Compare. + (+) Stop the TIM Output Compare. + (+) Start the TIM Output Compare and enable interrupt. + (+) Stop the TIM Output Compare and disable interrupt. + (+) Start the TIM Output Compare and enable DMA transfer. + (+) Stop the TIM Output Compare and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM Output Compare according to the specified - * parameters in the TIM_HandleTypeDef and create the associated handle. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * parameters in the TIM_HandleTypeDef and initializes the associated handle. + * @note Switching from Center Aligned counter mode to Edge counter mode (or reverse) + * requires a timer reset to avoid unexpected direction + * due to DIR bit readonly in center aligned mode. + * Ex: call @ref HAL_TIM_OC_DeInit() before HAL_TIM_OC_Init() + * @param htim TIM Output Compare handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Init(TIM_HandleTypeDef* htim) @@ -469,81 +612,114 @@ HAL_StatusTypeDef HAL_TIM_OC_Init(TIM_HandleTypeDef* htim) assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); + assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload)); if (htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + /* Reset interrupt callbacks to legacy weak callbacks */ + TIM_ResetCallback(htim); + + if (htim->OC_MspInitCallback == NULL) + { + htim->OC_MspInitCallback = HAL_TIM_OC_MspInit; + } + + /* Init the low level hardware : GPIO, CLOCK, NVIC */ + htim->OC_MspInitCallback(htim); +#else /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ HAL_TIM_OC_MspInit(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } /* Set the TIM state */ htim->State = HAL_TIM_STATE_BUSY; + /* Init the base time for the Output Compare */ TIM_Base_SetConfig(htim->Instance, &htim->Init); + /* Initialize the TIM state*/ htim->State = HAL_TIM_STATE_READY; + return HAL_OK; } /** * @brief DeInitializes the TIM peripheral - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Output Compare handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_DeInit(TIM_HandleTypeDef* htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); + htim->State = HAL_TIM_STATE_BUSY; + /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + + if (htim->OC_MspDeInitCallback == NULL) + { + htim->OC_MspDeInitCallback = HAL_TIM_OC_MspDeInit; + } + + /* DeInit the low level hardware */ + htim->OC_MspDeInitCallback(htim); +#else /* DeInit the low level hardware: GPIO, CLOCK, NVIC and DMA */ HAL_TIM_OC_MspDeInit(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; + /* Release Lock */ __HAL_UNLOCK(htim); + return HAL_OK; } /** * @brief Initializes the TIM Output Compare MSP. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Output Compare handle * @retval None */ __weak void HAL_TIM_OC_MspInit(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, + + /* NOTE : This function should not be modified, when the callback is needed, the HAL_TIM_OC_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM Output Compare MSP. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Output Compare handle * @retval None */ __weak void HAL_TIM_OC_MspDeInit(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, + + /* NOTE : This function should not be modified, when the callback is needed, the HAL_TIM_OC_MspDeInit could be implemented in the user file */ } /** * @brief Starts the TIM Output Compare signal generation. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be enabled. + * @param htim TIM Output Compare handle + * @param Channel TIM Channel to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -553,28 +729,36 @@ __weak void HAL_TIM_OC_MspDeInit(TIM_HandleTypeDef* htim) */ HAL_StatusTypeDef HAL_TIM_OC_Start(TIM_HandleTypeDef* htim, uint32_t Channel) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); + /* Enable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Output Compare signal generation. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be disabled. + * @param htim TIM Output Compare handle + * @param Channel TIM Channel to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -586,10 +770,11 @@ HAL_StatusTypeDef HAL_TIM_OC_Stop(TIM_HandleTypeDef* htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); + /* Disable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); @@ -597,15 +782,15 @@ HAL_StatusTypeDef HAL_TIM_OC_Stop(TIM_HandleTypeDef* htim, uint32_t Channel) /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Output Compare signal generation in interrupt mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be enabled. + * @param htim TIM Output Compare handle + * @param Channel TIM Channel to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -615,6 +800,8 @@ HAL_StatusTypeDef HAL_TIM_OC_Stop(TIM_HandleTypeDef* htim, uint32_t Channel) */ HAL_StatusTypeDef HAL_TIM_OC_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); @@ -624,29 +811,29 @@ HAL_StatusTypeDef HAL_TIM_OC_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel) { /* Enable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); + break; } - break; case TIM_CHANNEL_2: { /* Enable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); + break; } - break; case TIM_CHANNEL_3: { /* Enable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3); + break; } - break; case TIM_CHANNEL_4: { /* Enable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4); + break; } - break; default: break; @@ -655,23 +842,28 @@ HAL_StatusTypeDef HAL_TIM_OC_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel) /* Enable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Output Compare signal generation in interrupt mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be disabled. + * @param htim TIM Output Compare handle + * @param Channel TIM Channel to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -690,29 +882,29 @@ HAL_StatusTypeDef HAL_TIM_OC_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel) { /* Disable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); + break; } - break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); + break; } - break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3); + break; } - break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4); + break; } - break; default: break; @@ -721,7 +913,7 @@ HAL_StatusTypeDef HAL_TIM_OC_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel) /* Disable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); @@ -729,36 +921,38 @@ HAL_StatusTypeDef HAL_TIM_OC_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel) /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Output Compare signal generation in DMA mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be enabled. + * @param htim TIM Output Compare handle + * @param Channel TIM Channel to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected - * @param pData: The source Buffer address. - * @param Length: The length of data to be transferred from memory to TIM peripheral + * @param pData The source Buffer address. + * @param Length The length of data to be transferred from memory to TIM peripheral * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData, uint16_t Length) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); - if ((htim->State == HAL_TIM_STATE_BUSY)) + if (htim->State == HAL_TIM_STATE_BUSY) { return HAL_BUSY; } - else if ((htim->State == HAL_TIM_STATE_READY)) + else if (htim->State == HAL_TIM_STATE_READY) { - if (((uint32_t)pData == 0U) && (Length > 0U)) + if ((pData == NULL) && (Length > 0U)) { return HAL_ERROR; } @@ -767,60 +961,92 @@ HAL_StatusTypeDef HAL_TIM_OC_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel htim->State = HAL_TIM_STATE_BUSY; } } + else + { + /* nothing to do */ + } switch (Channel) { case TIM_CHANNEL_1: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); + break; } - break; case TIM_CHANNEL_2: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC2]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); + break; } - break; case TIM_CHANNEL_3: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC3]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3); + break; } - break; case TIM_CHANNEL_4: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC4]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Capture/Compare 4 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4); + break; } - break; default: break; @@ -829,23 +1055,28 @@ HAL_StatusTypeDef HAL_TIM_OC_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel /* Enable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Output Compare signal generation in DMA mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be disabled. + * @param htim TIM Output Compare handle + * @param Channel TIM Channel to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -864,29 +1095,33 @@ HAL_StatusTypeDef HAL_TIM_OC_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel) { /* Disable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]); + break; } - break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC2]); + break; } - break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC3]); + break; } - break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC4]); + break; } - break; default: break; @@ -895,7 +1130,7 @@ HAL_StatusTypeDef HAL_TIM_OC_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel) /* Disable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); @@ -903,41 +1138,47 @@ HAL_StatusTypeDef HAL_TIM_OC_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel) /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; + /* Return function status */ return HAL_OK; } + /** * @} */ -/** @defgroup TIM_Exported_Functions_Group3 Time PWM functions - * @brief Time PWM functions - * +/** @defgroup TIM_Exported_Functions_Group3 TIM PWM functions + * @brief TIM PWM functions + * @verbatim ============================================================================== - ##### Time PWM functions ##### + ##### TIM PWM functions ##### ============================================================================== [..] This section provides functions allowing to: - (+) Initialize and configure the TIM OPWM. + (+) Initialize and configure the TIM PWM. (+) De-initialize the TIM PWM. - (+) Start the Time PWM. - (+) Stop the Time PWM. - (+) Start the Time PWM and enable interrupt. - (+) Stop the Time PWM and disable interrupt. - (+) Start the Time PWM and enable DMA transfer. - (+) Stop the Time PWM and disable DMA transfer. + (+) Start the TIM PWM. + (+) Stop the TIM PWM. + (+) Start the TIM PWM and enable interrupt. + (+) Stop the TIM PWM and disable interrupt. + (+) Start the TIM PWM and enable DMA transfer. + (+) Stop the TIM PWM and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM PWM Time Base according to the specified - * parameters in the TIM_HandleTypeDef and create the associated handle. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * parameters in the TIM_HandleTypeDef and initializes the associated handle. + * @note Switching from Center Aligned counter mode to Edge counter mode (or reverse) + * requires a timer reset to avoid unexpected direction + * due to DIR bit readonly in center aligned mode. + * Ex: call @ref HAL_TIM_PWM_DeInit() before HAL_TIM_PWM_Init() + * @param htim TIM PWM handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Init(TIM_HandleTypeDef* htim) @@ -952,81 +1193,114 @@ HAL_StatusTypeDef HAL_TIM_PWM_Init(TIM_HandleTypeDef* htim) assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); + assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload)); if (htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + /* Reset interrupt callbacks to legacy weak callbacks */ + TIM_ResetCallback(htim); + + if (htim->PWM_MspInitCallback == NULL) + { + htim->PWM_MspInitCallback = HAL_TIM_PWM_MspInit; + } + + /* Init the low level hardware : GPIO, CLOCK, NVIC */ + htim->PWM_MspInitCallback(htim); +#else /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ HAL_TIM_PWM_MspInit(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } /* Set the TIM state */ htim->State = HAL_TIM_STATE_BUSY; + /* Init the base time for the PWM */ TIM_Base_SetConfig(htim->Instance, &htim->Init); + /* Initialize the TIM state*/ htim->State = HAL_TIM_STATE_READY; + return HAL_OK; } /** * @brief DeInitializes the TIM peripheral - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM PWM handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_DeInit(TIM_HandleTypeDef* htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); + htim->State = HAL_TIM_STATE_BUSY; + /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + + if (htim->PWM_MspDeInitCallback == NULL) + { + htim->PWM_MspDeInitCallback = HAL_TIM_PWM_MspDeInit; + } + + /* DeInit the low level hardware */ + htim->PWM_MspDeInitCallback(htim); +#else /* DeInit the low level hardware: GPIO, CLOCK, NVIC and DMA */ HAL_TIM_PWM_MspDeInit(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; + /* Release Lock */ __HAL_UNLOCK(htim); + return HAL_OK; } /** * @brief Initializes the TIM PWM MSP. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM PWM handle * @retval None */ __weak void HAL_TIM_PWM_MspInit(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, + + /* NOTE : This function should not be modified, when the callback is needed, the HAL_TIM_PWM_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM PWM MSP. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM PWM handle * @retval None */ __weak void HAL_TIM_PWM_MspDeInit(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, + + /* NOTE : This function should not be modified, when the callback is needed, the HAL_TIM_PWM_MspDeInit could be implemented in the user file */ } /** * @brief Starts the PWM signal generation. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be enabled. + * @param htim TIM handle + * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1036,28 +1310,36 @@ __weak void HAL_TIM_PWM_MspDeInit(TIM_HandleTypeDef* htim) */ HAL_StatusTypeDef HAL_TIM_PWM_Start(TIM_HandleTypeDef* htim, uint32_t Channel) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); + /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } /** * @brief Stops the PWM signal generation. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be disabled. + * @param htim TIM PWM handle + * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1069,10 +1351,11 @@ HAL_StatusTypeDef HAL_TIM_PWM_Stop(TIM_HandleTypeDef* htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); + /* Disable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); @@ -1080,17 +1363,18 @@ HAL_StatusTypeDef HAL_TIM_PWM_Stop(TIM_HandleTypeDef* htim, uint32_t Channel) /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; + /* Return function status */ return HAL_OK; } /** * @brief Starts the PWM signal generation in interrupt mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be disabled. + * @param htim TIM PWM handle + * @param Channel TIM Channel to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1100,6 +1384,7 @@ HAL_StatusTypeDef HAL_TIM_PWM_Stop(TIM_HandleTypeDef* htim, uint32_t Channel) */ HAL_StatusTypeDef HAL_TIM_PWM_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel) { + uint32_t tmpsmcr; /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); @@ -1109,29 +1394,29 @@ HAL_StatusTypeDef HAL_TIM_PWM_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel { /* Enable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); + break; } - break; case TIM_CHANNEL_2: { /* Enable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); + break; } - break; case TIM_CHANNEL_3: { /* Enable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3); + break; } - break; case TIM_CHANNEL_4: { /* Enable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4); + break; } - break; default: break; @@ -1140,23 +1425,28 @@ HAL_StatusTypeDef HAL_TIM_PWM_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } /** * @brief Stops the PWM signal generation in interrupt mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be disabled. + * @param htim TIM PWM handle + * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1164,7 +1454,7 @@ HAL_StatusTypeDef HAL_TIM_PWM_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ -HAL_StatusTypeDef HAL_TIM_PWM_Stop_IT (TIM_HandleTypeDef* htim, uint32_t Channel) +HAL_StatusTypeDef HAL_TIM_PWM_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); @@ -1175,29 +1465,29 @@ HAL_StatusTypeDef HAL_TIM_PWM_Stop_IT (TIM_HandleTypeDef* htim, uint32_t Channel { /* Disable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); + break; } - break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); + break; } - break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3); + break; } - break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4); + break; } - break; default: break; @@ -1206,7 +1496,7 @@ HAL_StatusTypeDef HAL_TIM_PWM_Stop_IT (TIM_HandleTypeDef* htim, uint32_t Channel /* Disable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); @@ -1214,36 +1504,38 @@ HAL_StatusTypeDef HAL_TIM_PWM_Stop_IT (TIM_HandleTypeDef* htim, uint32_t Channel /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM PWM signal generation in DMA mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be enabled. + * @param htim TIM PWM handle + * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected - * @param pData: The source Buffer address. - * @param Length: The length of data to be transferred from memory to TIM peripheral + * @param pData The source Buffer address. + * @param Length The length of data to be transferred from memory to TIM peripheral * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData, uint16_t Length) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); - if ((htim->State == HAL_TIM_STATE_BUSY)) + if (htim->State == HAL_TIM_STATE_BUSY) { return HAL_BUSY; } - else if ((htim->State == HAL_TIM_STATE_READY)) + else if (htim->State == HAL_TIM_STATE_READY) { - if (((uint32_t)pData == 0U) && (Length > 0U)) + if ((pData == NULL) && (Length > 0U)) { return HAL_ERROR; } @@ -1252,60 +1544,92 @@ HAL_StatusTypeDef HAL_TIM_PWM_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channe htim->State = HAL_TIM_STATE_BUSY; } } + else + { + /* nothing to do */ + } switch (Channel) { case TIM_CHANNEL_1: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); + break; } - break; case TIM_CHANNEL_2: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC2]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); + break; } - break; case TIM_CHANNEL_3: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC3]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Output Capture/Compare 3 request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3); + break; } - break; case TIM_CHANNEL_4: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC4]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Capture/Compare 4 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4); + break; } - break; default: break; @@ -1314,23 +1638,28 @@ HAL_StatusTypeDef HAL_TIM_PWM_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channe /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM PWM signal generation in DMA mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be disabled. + * @param htim TIM PWM handle + * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1349,29 +1678,33 @@ HAL_StatusTypeDef HAL_TIM_PWM_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel { /* Disable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]); + break; } - break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC2]); + break; } - break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC3]); + break; } - break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC4]); + break; } - break; default: break; @@ -1380,7 +1713,7 @@ HAL_StatusTypeDef HAL_TIM_PWM_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel /* Disable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); @@ -1388,41 +1721,47 @@ HAL_StatusTypeDef HAL_TIM_PWM_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; + /* Return function status */ return HAL_OK; } + /** * @} */ -/** @defgroup TIM_Exported_Functions_Group4 Time Input Capture functions - * @brief Time Input Capture functions - * +/** @defgroup TIM_Exported_Functions_Group4 TIM Input Capture functions + * @brief TIM Input Capture functions + * @verbatim ============================================================================== - ##### Time Input Capture functions ##### + ##### TIM Input Capture functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM Input Capture. (+) De-initialize the TIM Input Capture. - (+) Start the Time Input Capture. - (+) Stop the Time Input Capture. - (+) Start the Time Input Capture and enable interrupt. - (+) Stop the Time Input Capture and disable interrupt. - (+) Start the Time Input Capture and enable DMA transfer. - (+) Stop the Time Input Capture and disable DMA transfer. + (+) Start the TIM Input Capture. + (+) Stop the TIM Input Capture. + (+) Start the TIM Input Capture and enable interrupt. + (+) Stop the TIM Input Capture and disable interrupt. + (+) Start the TIM Input Capture and enable DMA transfer. + (+) Stop the TIM Input Capture and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM Input Capture Time base according to the specified - * parameters in the TIM_HandleTypeDef and create the associated handle. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * parameters in the TIM_HandleTypeDef and initializes the associated handle. + * @note Switching from Center Aligned counter mode to Edge counter mode (or reverse) + * requires a timer reset to avoid unexpected direction + * due to DIR bit readonly in center aligned mode. + * Ex: call @ref HAL_TIM_IC_DeInit() before HAL_TIM_IC_Init() + * @param htim TIM Input Capture handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Init(TIM_HandleTypeDef* htim) @@ -1437,81 +1776,114 @@ HAL_StatusTypeDef HAL_TIM_IC_Init(TIM_HandleTypeDef* htim) assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); + assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload)); if (htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + /* Reset interrupt callbacks to legacy weak callbacks */ + TIM_ResetCallback(htim); + + if (htim->IC_MspInitCallback == NULL) + { + htim->IC_MspInitCallback = HAL_TIM_IC_MspInit; + } + + /* Init the low level hardware : GPIO, CLOCK, NVIC */ + htim->IC_MspInitCallback(htim); +#else /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ HAL_TIM_IC_MspInit(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } /* Set the TIM state */ htim->State = HAL_TIM_STATE_BUSY; + /* Init the base time for the input capture */ TIM_Base_SetConfig(htim->Instance, &htim->Init); + /* Initialize the TIM state*/ htim->State = HAL_TIM_STATE_READY; + return HAL_OK; } /** * @brief DeInitializes the TIM peripheral - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Input Capture handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_DeInit(TIM_HandleTypeDef* htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); + htim->State = HAL_TIM_STATE_BUSY; + /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + + if (htim->IC_MspDeInitCallback == NULL) + { + htim->IC_MspDeInitCallback = HAL_TIM_IC_MspDeInit; + } + + /* DeInit the low level hardware */ + htim->IC_MspDeInitCallback(htim); +#else /* DeInit the low level hardware: GPIO, CLOCK, NVIC and DMA */ HAL_TIM_IC_MspDeInit(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; + /* Release Lock */ __HAL_UNLOCK(htim); + return HAL_OK; } /** - * @brief Initializes the TIM INput Capture MSP. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @brief Initializes the TIM Input Capture MSP. + * @param htim TIM Input Capture handle * @retval None */ __weak void HAL_TIM_IC_MspInit(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, + + /* NOTE : This function should not be modified, when the callback is needed, the HAL_TIM_IC_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM Input Capture MSP. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM handle * @retval None */ __weak void HAL_TIM_IC_MspDeInit(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, + + /* NOTE : This function should not be modified, when the callback is needed, the HAL_TIM_IC_MspDeInit could be implemented in the user file */ } /** * @brief Starts the TIM Input Capture measurement. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be enabled. + * @param htim TIM Input Capture handle + * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1519,23 +1891,32 @@ __weak void HAL_TIM_IC_MspDeInit(TIM_HandleTypeDef* htim) * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ -HAL_StatusTypeDef HAL_TIM_IC_Start (TIM_HandleTypeDef* htim, uint32_t Channel) +HAL_StatusTypeDef HAL_TIM_IC_Start(TIM_HandleTypeDef* htim, uint32_t Channel) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); + /* Enable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Input Capture measurement. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be disabled. + * @param htim TIM Input Capture handle + * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1547,19 +1928,21 @@ HAL_StatusTypeDef HAL_TIM_IC_Stop(TIM_HandleTypeDef* htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); + /* Disable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Input Capture measurement in interrupt mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be enabled. + * @param htim TIM Input Capture handle + * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1567,8 +1950,10 @@ HAL_StatusTypeDef HAL_TIM_IC_Stop(TIM_HandleTypeDef* htim, uint32_t Channel) * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ -HAL_StatusTypeDef HAL_TIM_IC_Start_IT (TIM_HandleTypeDef* htim, uint32_t Channel) +HAL_StatusTypeDef HAL_TIM_IC_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); @@ -1578,29 +1963,29 @@ HAL_StatusTypeDef HAL_TIM_IC_Start_IT (TIM_HandleTypeDef* htim, uint32_t Channel { /* Enable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); + break; } - break; case TIM_CHANNEL_2: { /* Enable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); + break; } - break; case TIM_CHANNEL_3: { /* Enable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3); + break; } - break; case TIM_CHANNEL_4: { /* Enable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4); + break; } - break; default: break; @@ -1608,17 +1993,23 @@ HAL_StatusTypeDef HAL_TIM_IC_Start_IT (TIM_HandleTypeDef* htim, uint32_t Channel /* Enable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Input Capture measurement in interrupt mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be disabled. + * @param htim TIM Input Capture handle + * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1637,29 +2028,29 @@ HAL_StatusTypeDef HAL_TIM_IC_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel) { /* Disable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); + break; } - break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); + break; } - break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3); + break; } - break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4); + break; } - break; default: break; @@ -1667,39 +2058,42 @@ HAL_StatusTypeDef HAL_TIM_IC_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel) /* Disable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } /** - * @brief Starts the TIM Input Capture measurement on in DMA mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be enabled. + * @brief Starts the TIM Input Capture measurement in DMA mode. + * @param htim TIM Input Capture handle + * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected - * @param pData: The destination Buffer address. - * @param Length: The length of data to be transferred from TIM peripheral to memory. + * @param pData The destination Buffer address. + * @param Length The length of data to be transferred from TIM peripheral to memory. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData, uint16_t Length) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance)); - if ((htim->State == HAL_TIM_STATE_BUSY)) + if (htim->State == HAL_TIM_STATE_BUSY) { return HAL_BUSY; } - else if ((htim->State == HAL_TIM_STATE_READY)) + else if (htim->State == HAL_TIM_STATE_READY) { - if ((pData == 0U) && (Length > 0U)) + if ((pData == NULL) && (Length > 0U)) { return HAL_ERROR; } @@ -1708,60 +2102,92 @@ HAL_StatusTypeDef HAL_TIM_IC_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel htim->State = HAL_TIM_STATE_BUSY; } } + else + { + /* nothing to do */ + } switch (Channel) { case TIM_CHANNEL_1: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA capture callbacks */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt; + htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMACaptureHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); + break; } - break; case TIM_CHANNEL_2: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA capture callbacks */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt; + htim->hdma[TIM_DMA_ID_CC2]->XferHalfCpltCallback = TIM_DMACaptureHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); + break; } - break; case TIM_CHANNEL_3: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA capture callbacks */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMACaptureCplt; + htim->hdma[TIM_DMA_ID_CC3]->XferHalfCpltCallback = TIM_DMACaptureHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)&htim->Instance->CCR3, (uint32_t)pData, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)&htim->Instance->CCR3, (uint32_t)pData, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3); + break; } - break; case TIM_CHANNEL_4: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA capture callbacks */ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMACaptureCplt; + htim->hdma[TIM_DMA_ID_CC4]->XferHalfCpltCallback = TIM_DMACaptureHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)&htim->Instance->CCR4, (uint32_t)pData, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)&htim->Instance->CCR4, (uint32_t)pData, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Capture/Compare 4 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4); + break; } - break; default: break; @@ -1769,17 +2195,23 @@ HAL_StatusTypeDef HAL_TIM_IC_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel /* Enable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } /** - * @brief Stops the TIM Input Capture measurement on in DMA mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be disabled. + * @brief Stops the TIM Input Capture measurement in DMA mode. + * @param htim TIM Input Capture handle + * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1799,29 +2231,33 @@ HAL_StatusTypeDef HAL_TIM_IC_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel) { /* Disable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]); + break; } - break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC2]); + break; } - break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC3]); + break; } - break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC4]); + break; } - break; default: break; @@ -1829,10 +2265,13 @@ HAL_StatusTypeDef HAL_TIM_IC_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel) /* Disable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; + /* Return function status */ return HAL_OK; } @@ -1840,33 +2279,36 @@ HAL_StatusTypeDef HAL_TIM_IC_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel) * @} */ -/** @defgroup TIM_Exported_Functions_Group5 Time One Pulse functions - * @brief Time One Pulse functions - * +/** @defgroup TIM_Exported_Functions_Group5 TIM One Pulse functions + * @brief TIM One Pulse functions + * @verbatim ============================================================================== - ##### Time One Pulse functions ##### + ##### TIM One Pulse functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM One Pulse. (+) De-initialize the TIM One Pulse. - (+) Start the Time One Pulse. - (+) Stop the Time One Pulse. - (+) Start the Time One Pulse and enable interrupt. - (+) Stop the Time One Pulse and disable interrupt. - (+) Start the Time One Pulse and enable DMA transfer. - (+) Stop the Time One Pulse and disable DMA transfer. + (+) Start the TIM One Pulse. + (+) Stop the TIM One Pulse. + (+) Start the TIM One Pulse and enable interrupt. + (+) Stop the TIM One Pulse and disable interrupt. + (+) Start the TIM One Pulse and enable DMA transfer. + (+) Stop the TIM One Pulse and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM One Pulse Time Base according to the specified - * parameters in the TIM_HandleTypeDef and create the associated handle. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param OnePulseMode: Select the One pulse mode. + * parameters in the TIM_HandleTypeDef and initializes the associated handle. + * @note Switching from Center Aligned counter mode to Edge counter mode (or reverse) + * requires a timer reset to avoid unexpected direction + * due to DIR bit readonly in center aligned mode. + * Ex: call @ref HAL_TIM_OnePulse_DeInit() before HAL_TIM_OnePulse_Init() + * @param htim TIM One Pulse handle + * @param OnePulseMode Select the One pulse mode. * This parameter can be one of the following values: * @arg TIM_OPMODE_SINGLE: Only one pulse will be generated. * @arg TIM_OPMODE_REPETITIVE: Repetitive pulses will be generated. @@ -1885,85 +2327,120 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_Init(TIM_HandleTypeDef* htim, uint32_t OnePul assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); assert_param(IS_TIM_OPM_MODE(OnePulseMode)); + assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload)); if (htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + /* Reset interrupt callbacks to legacy weak callbacks */ + TIM_ResetCallback(htim); + + if (htim->OnePulse_MspInitCallback == NULL) + { + htim->OnePulse_MspInitCallback = HAL_TIM_OnePulse_MspInit; + } + + /* Init the low level hardware : GPIO, CLOCK, NVIC */ + htim->OnePulse_MspInitCallback(htim); +#else /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ HAL_TIM_OnePulse_MspInit(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } /* Set the TIM state */ htim->State = HAL_TIM_STATE_BUSY; + /* Configure the Time base in the One Pulse Mode */ TIM_Base_SetConfig(htim->Instance, &htim->Init); + /* Reset the OPM Bit */ htim->Instance->CR1 &= ~TIM_CR1_OPM; + /* Configure the OPM Mode */ htim->Instance->CR1 |= OnePulseMode; + /* Initialize the TIM state*/ htim->State = HAL_TIM_STATE_READY; + return HAL_OK; } /** * @brief DeInitializes the TIM One Pulse - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM One Pulse handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OnePulse_DeInit(TIM_HandleTypeDef* htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); + htim->State = HAL_TIM_STATE_BUSY; + /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + + if (htim->OnePulse_MspDeInitCallback == NULL) + { + htim->OnePulse_MspDeInitCallback = HAL_TIM_OnePulse_MspDeInit; + } + + /* DeInit the low level hardware */ + htim->OnePulse_MspDeInitCallback(htim); +#else /* DeInit the low level hardware: GPIO, CLOCK, NVIC */ HAL_TIM_OnePulse_MspDeInit(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; + /* Release Lock */ __HAL_UNLOCK(htim); + return HAL_OK; } /** * @brief Initializes the TIM One Pulse MSP. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM One Pulse handle * @retval None */ __weak void HAL_TIM_OnePulse_MspInit(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, + + /* NOTE : This function should not be modified, when the callback is needed, the HAL_TIM_OnePulse_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM One Pulse MSP. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM One Pulse handle * @retval None */ __weak void HAL_TIM_OnePulse_MspDeInit(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, + + /* NOTE : This function should not be modified, when the callback is needed, the HAL_TIM_OnePulse_MspDeInit could be implemented in the user file */ } /** * @brief Starts the TIM One Pulse signal generation. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param OutputChannel : TIM Channels to be enabled. + * @param htim TIM One Pulse handle + * @param OutputChannel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1971,6 +2448,9 @@ __weak void HAL_TIM_OnePulse_MspDeInit(TIM_HandleTypeDef* htim) */ HAL_StatusTypeDef HAL_TIM_OnePulse_Start(TIM_HandleTypeDef* htim, uint32_t OutputChannel) { + /* Prevent unused argument(s) compilation warning */ + UNUSED(OutputChannel); + /* Enable the Capture compare and the Input Capture channels (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and @@ -1979,10 +2459,11 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_Start(TIM_HandleTypeDef* htim, uint32_t Outpu No need to enable the counter, it's enabled automatically by hardware (the counter starts in response to a stimulus and generate a pulse */ + TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); @@ -1994,9 +2475,8 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_Start(TIM_HandleTypeDef* htim, uint32_t Outpu /** * @brief Stops the TIM One Pulse signal generation. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param OutputChannel : TIM Channels to be disable. + * @param htim TIM One Pulse handle + * @param OutputChannel TIM Channels to be disable * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -2004,15 +2484,19 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_Start(TIM_HandleTypeDef* htim, uint32_t Outpu */ HAL_StatusTypeDef HAL_TIM_OnePulse_Stop(TIM_HandleTypeDef* htim, uint32_t OutputChannel) { + /* Prevent unused argument(s) compilation warning */ + UNUSED(OutputChannel); + /* Disable the Capture compare and the Input Capture channels (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be disabled together */ + TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); @@ -2020,15 +2504,15 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_Stop(TIM_HandleTypeDef* htim, uint32_t Output /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM One Pulse signal generation in interrupt mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param OutputChannel : TIM Channels to be enabled. + * @param htim TIM One Pulse handle + * @param OutputChannel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -2036,6 +2520,9 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_Stop(TIM_HandleTypeDef* htim, uint32_t Output */ HAL_StatusTypeDef HAL_TIM_OnePulse_Start_IT(TIM_HandleTypeDef* htim, uint32_t OutputChannel) { + /* Prevent unused argument(s) compilation warning */ + UNUSED(OutputChannel); + /* Enable the Capture compare and the Input Capture channels (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and @@ -2044,14 +2531,17 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_Start_IT(TIM_HandleTypeDef* htim, uint32_t Ou No need to enable the counter, it's enabled automatically by hardware (the counter starts in response to a stimulus and generate a pulse */ + /* Enable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); + /* Enable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); + TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); @@ -2063,9 +2553,8 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_Start_IT(TIM_HandleTypeDef* htim, uint32_t Ou /** * @brief Stops the TIM One Pulse signal generation in interrupt mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param OutputChannel : TIM Channels to be enabled. + * @param htim TIM One Pulse handle + * @param OutputChannel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -2073,10 +2562,15 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_Start_IT(TIM_HandleTypeDef* htim, uint32_t Ou */ HAL_StatusTypeDef HAL_TIM_OnePulse_Stop_IT(TIM_HandleTypeDef* htim, uint32_t OutputChannel) { + /* Prevent unused argument(s) compilation warning */ + UNUSED(OutputChannel); + /* Disable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); + /* Disable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); + /* Disable the Capture compare and the Input Capture channels (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and @@ -2085,7 +2579,7 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Out TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); - if (IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) + if (IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); @@ -2093,46 +2587,54 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Out /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } + /** * @} */ -/** @defgroup TIM_Exported_Functions_Group6 Time Encoder functions - * @brief Time Encoder functions - * +/** @defgroup TIM_Exported_Functions_Group6 TIM Encoder functions + * @brief TIM Encoder functions + * @verbatim ============================================================================== - ##### Time Encoder functions ##### + ##### TIM Encoder functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM Encoder. (+) De-initialize the TIM Encoder. - (+) Start the Time Encoder. - (+) Stop the Time Encoder. - (+) Start the Time Encoder and enable interrupt. - (+) Stop the Time Encoder and disable interrupt. - (+) Start the Time Encoder and enable DMA transfer. - (+) Stop the Time Encoder and disable DMA transfer. + (+) Start the TIM Encoder. + (+) Stop the TIM Encoder. + (+) Start the TIM Encoder and enable interrupt. + (+) Stop the TIM Encoder and disable interrupt. + (+) Start the TIM Encoder and enable DMA transfer. + (+) Stop the TIM Encoder and disable DMA transfer. @endverbatim * @{ */ /** - * @brief Initializes the TIM Encoder Interface and create the associated handle. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param sConfig: TIM Encoder Interface configuration structure + * @brief Initializes the TIM Encoder Interface and initialize the associated handle. + * @note Switching from Center Aligned counter mode to Edge counter mode (or reverse) + * requires a timer reset to avoid unexpected direction + * due to DIR bit readonly in center aligned mode. + * Ex: call @ref HAL_TIM_Encoder_DeInit() before HAL_TIM_Encoder_Init() + * @note Encoder mode and External clock mode 2 are not compatible and must not be selected together + * Ex: A call for @ref HAL_TIM_Encoder_Init will erase the settings of @ref HAL_TIM_ConfigClockSource + * using TIM_CLOCKSOURCE_ETRMODE2 and vice versa + * @param htim TIM Encoder Interface handle + * @param sConfig TIM Encoder Interface configuration structure * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_Init(TIM_HandleTypeDef* htim, TIM_Encoder_InitTypeDef* sConfig) { - uint32_t tmpsmcr = 0U; - uint32_t tmpccmr1 = 0U; - uint32_t tmpccer = 0U; + uint32_t tmpsmcr; + uint32_t tmpccmr1; + uint32_t tmpccer; /* Check the TIM handle allocation */ if (htim == NULL) @@ -2141,6 +2643,9 @@ HAL_StatusTypeDef HAL_TIM_Encoder_Init(TIM_HandleTypeDef* htim, TIM_Encoder_Ini } /* Check the parameters */ + assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); + assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); + assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload)); assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); assert_param(IS_TIM_ENCODER_MODE(sConfig->EncoderMode)); assert_param(IS_TIM_IC_SELECTION(sConfig->IC1Selection)); @@ -2156,104 +2661,147 @@ HAL_StatusTypeDef HAL_TIM_Encoder_Init(TIM_HandleTypeDef* htim, TIM_Encoder_Ini { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + /* Reset interrupt callbacks to legacy weak callbacks */ + TIM_ResetCallback(htim); + + if (htim->Encoder_MspInitCallback == NULL) + { + htim->Encoder_MspInitCallback = HAL_TIM_Encoder_MspInit; + } + + /* Init the low level hardware : GPIO, CLOCK, NVIC */ + htim->Encoder_MspInitCallback(htim); +#else /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ HAL_TIM_Encoder_MspInit(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } /* Set the TIM state */ htim->State = HAL_TIM_STATE_BUSY; - /* Reset the SMS bits */ - htim->Instance->SMCR &= ~TIM_SMCR_SMS; + + /* Reset the SMS and ECE bits */ + htim->Instance->SMCR &= ~(TIM_SMCR_SMS | TIM_SMCR_ECE); + /* Configure the Time base in the Encoder Mode */ TIM_Base_SetConfig(htim->Instance, &htim->Init); + /* Get the TIMx SMCR register value */ tmpsmcr = htim->Instance->SMCR; + /* Get the TIMx CCMR1 register value */ tmpccmr1 = htim->Instance->CCMR1; + /* Get the TIMx CCER register value */ tmpccer = htim->Instance->CCER; + /* Set the encoder Mode */ tmpsmcr |= sConfig->EncoderMode; + /* Select the Capture Compare 1 and the Capture Compare 2 as input */ tmpccmr1 &= ~(TIM_CCMR1_CC1S | TIM_CCMR1_CC2S); tmpccmr1 |= (sConfig->IC1Selection | (sConfig->IC2Selection << 8U)); + /* Set the Capture Compare 1 and the Capture Compare 2 prescalers and filters */ tmpccmr1 &= ~(TIM_CCMR1_IC1PSC | TIM_CCMR1_IC2PSC); tmpccmr1 &= ~(TIM_CCMR1_IC1F | TIM_CCMR1_IC2F); tmpccmr1 |= sConfig->IC1Prescaler | (sConfig->IC2Prescaler << 8U); tmpccmr1 |= (sConfig->IC1Filter << 4U) | (sConfig->IC2Filter << 12U); + /* Set the TI1 and the TI2 Polarities */ tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC2P); - tmpccer &= ~(TIM_CCER_CC1NP | TIM_CCER_CC2NP); tmpccer |= sConfig->IC1Polarity | (sConfig->IC2Polarity << 4U); + /* Write to TIMx SMCR */ htim->Instance->SMCR = tmpsmcr; + /* Write to TIMx CCMR1 */ htim->Instance->CCMR1 = tmpccmr1; + /* Write to TIMx CCER */ htim->Instance->CCER = tmpccer; + /* Initialize the TIM state*/ htim->State = HAL_TIM_STATE_READY; + return HAL_OK; } + /** * @brief DeInitializes the TIM Encoder interface - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Encoder Interface handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_DeInit(TIM_HandleTypeDef* htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); + htim->State = HAL_TIM_STATE_BUSY; + /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + + if (htim->Encoder_MspDeInitCallback == NULL) + { + htim->Encoder_MspDeInitCallback = HAL_TIM_Encoder_MspDeInit; + } + + /* DeInit the low level hardware */ + htim->Encoder_MspDeInitCallback(htim); +#else /* DeInit the low level hardware: GPIO, CLOCK, NVIC */ HAL_TIM_Encoder_MspDeInit(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; + /* Release Lock */ __HAL_UNLOCK(htim); + return HAL_OK; } /** * @brief Initializes the TIM Encoder Interface MSP. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Encoder Interface handle * @retval None */ __weak void HAL_TIM_Encoder_MspInit(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, + + /* NOTE : This function should not be modified, when the callback is needed, the HAL_TIM_Encoder_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM Encoder Interface MSP. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Encoder Interface handle * @retval None */ __weak void HAL_TIM_Encoder_MspDeInit(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, + + /* NOTE : This function should not be modified, when the callback is needed, the HAL_TIM_Encoder_MspDeInit could be implemented in the user file */ } /** * @brief Starts the TIM Encoder Interface. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be enabled. + * @param htim TIM Encoder Interface handle + * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -2290,15 +2838,15 @@ HAL_StatusTypeDef HAL_TIM_Encoder_Start(TIM_HandleTypeDef* htim, uint32_t Channe /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); + /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Encoder Interface. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be disabled. + * @param htim TIM Encoder Interface handle + * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -2311,7 +2859,7 @@ HAL_StatusTypeDef HAL_TIM_Encoder_Stop(TIM_HandleTypeDef* htim, uint32_t Channel assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Disable the Input Capture channels 1 and 2 - (in the EncoderInterface the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) */ + (in the EncoderInterface the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) */ switch (Channel) { case TIM_CHANNEL_1: @@ -2336,15 +2884,15 @@ HAL_StatusTypeDef HAL_TIM_Encoder_Stop(TIM_HandleTypeDef* htim, uint32_t Channel /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Encoder Interface in interrupt mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be enabled. + * @param htim TIM Encoder Interface handle + * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -2386,15 +2934,15 @@ HAL_StatusTypeDef HAL_TIM_Encoder_Start_IT(TIM_HandleTypeDef* htim, uint32_t Cha /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); + /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Encoder Interface in interrupt mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be disabled. + * @param htim TIM Encoder Interface handle + * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -2411,12 +2959,14 @@ HAL_StatusTypeDef HAL_TIM_Encoder_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Chan if (Channel == TIM_CHANNEL_1) { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); + /* Disable the capture compare Interrupts 1 */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); } else if (Channel == TIM_CHANNEL_2) { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); + /* Disable the capture compare Interrupts 2 */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); } @@ -2424,6 +2974,7 @@ HAL_StatusTypeDef HAL_TIM_Encoder_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Chan { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); + /* Disable the capture compare Interrupts 1 and 2 */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); @@ -2431,38 +2982,40 @@ HAL_StatusTypeDef HAL_TIM_Encoder_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Chan /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; + /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Encoder Interface in DMA mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be enabled. + * @param htim TIM Encoder Interface handle + * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected - * @param pData1: The destination Buffer address for IC1. - * @param pData2: The destination Buffer address for IC2. - * @param Length: The length of data to be transferred from TIM peripheral to memory. + * @param pData1 The destination Buffer address for IC1. + * @param pData2 The destination Buffer address for IC2. + * @param Length The length of data to be transferred from TIM peripheral to memory. * @retval HAL status */ -HAL_StatusTypeDef HAL_TIM_Encoder_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData1, uint32_t* pData2, uint16_t Length) +HAL_StatusTypeDef HAL_TIM_Encoder_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData1, + uint32_t* pData2, uint16_t Length) { /* Check the parameters */ assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance)); - if ((htim->State == HAL_TIM_STATE_BUSY)) + if (htim->State == HAL_TIM_STATE_BUSY) { return HAL_BUSY; } - else if ((htim->State == HAL_TIM_STATE_READY)) + else if (htim->State == HAL_TIM_STATE_READY) { - if ((((pData1 == 0U) || (pData2 == 0U) )) && (Length > 0U)) + if ((((pData1 == NULL) || (pData2 == NULL))) && (Length > 0U)) { return HAL_ERROR; } @@ -2471,68 +3024,106 @@ HAL_StatusTypeDef HAL_TIM_Encoder_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Ch htim->State = HAL_TIM_STATE_BUSY; } } + else + { + /* nothing to do */ + } switch (Channel) { case TIM_CHANNEL_1: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA capture callbacks */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt; + htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMACaptureHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t )pData1, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData1, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Input Capture DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); + /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); + /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); + break; } - break; case TIM_CHANNEL_2: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA capture callbacks */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt; + htim->hdma[TIM_DMA_ID_CC2]->XferHalfCpltCallback = TIM_DMACaptureHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData2, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData2, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Input Capture DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); + /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); + /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); + break; } - break; case TIM_CHANNEL_ALL: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA capture callbacks */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt; + htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMACaptureHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData1, Length); - /* Set the DMA Period elapsed callback */ + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData1, Length) != HAL_OK) + { + return HAL_ERROR; + } + + /* Set the DMA capture callbacks */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt; + htim->hdma[TIM_DMA_ID_CC2]->XferHalfCpltCallback = TIM_DMACaptureHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData2, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData2, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); + /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); + /* Enable the TIM Input Capture DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); /* Enable the TIM Input Capture DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); + break; } - break; default: break; @@ -2544,9 +3135,8 @@ HAL_StatusTypeDef HAL_TIM_Encoder_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Ch /** * @brief Stops the TIM Encoder Interface in DMA mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be enabled. + * @param htim TIM Encoder Interface handle + * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -2563,38 +3153,47 @@ HAL_StatusTypeDef HAL_TIM_Encoder_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Cha if (Channel == TIM_CHANNEL_1) { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); + /* Disable the capture compare DMA Request 1 */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]); } else if (Channel == TIM_CHANNEL_2) { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); + /* Disable the capture compare DMA Request 2 */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC2]); } else { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); + /* Disable the capture compare DMA Request 1 and 2 */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC2]); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; + /* Return function status */ return HAL_OK; } + /** * @} */ - /** @defgroup TIM_Exported_Functions_Group7 TIM IRQ handler management - * @brief IRQ handler management - * + * @brief TIM IRQ handler management + * @verbatim ============================================================================== ##### IRQ handler management ##### @@ -2607,8 +3206,7 @@ HAL_StatusTypeDef HAL_TIM_Encoder_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Cha */ /** * @brief This function handles TIM interrupts requests. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM handle * @retval None */ void HAL_TIM_IRQHandler(TIM_HandleTypeDef* htim) @@ -2625,13 +3223,22 @@ void HAL_TIM_IRQHandler(TIM_HandleTypeDef* htim) /* Input capture event */ if ((htim->Instance->CCMR1 & TIM_CCMR1_CC1S) != 0x00U) { +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->IC_CaptureCallback(htim); +#else HAL_TIM_IC_CaptureCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } /* Output compare event */ else { +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->OC_DelayElapsedCallback(htim); + htim->PWM_PulseFinishedCallback(htim); +#else HAL_TIM_OC_DelayElapsedCallback(htim); HAL_TIM_PWM_PulseFinishedCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; @@ -2650,13 +3257,22 @@ void HAL_TIM_IRQHandler(TIM_HandleTypeDef* htim) /* Input capture event */ if ((htim->Instance->CCMR1 & TIM_CCMR1_CC2S) != 0x00U) { +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->IC_CaptureCallback(htim); +#else HAL_TIM_IC_CaptureCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } /* Output compare event */ else { +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->OC_DelayElapsedCallback(htim); + htim->PWM_PulseFinishedCallback(htim); +#else HAL_TIM_OC_DelayElapsedCallback(htim); HAL_TIM_PWM_PulseFinishedCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; @@ -2674,13 +3290,22 @@ void HAL_TIM_IRQHandler(TIM_HandleTypeDef* htim) /* Input capture event */ if ((htim->Instance->CCMR2 & TIM_CCMR2_CC3S) != 0x00U) { +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->IC_CaptureCallback(htim); +#else HAL_TIM_IC_CaptureCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } /* Output compare event */ else { +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->OC_DelayElapsedCallback(htim); + htim->PWM_PulseFinishedCallback(htim); +#else HAL_TIM_OC_DelayElapsedCallback(htim); HAL_TIM_PWM_PulseFinishedCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; @@ -2698,13 +3323,22 @@ void HAL_TIM_IRQHandler(TIM_HandleTypeDef* htim) /* Input capture event */ if ((htim->Instance->CCMR2 & TIM_CCMR2_CC4S) != 0x00U) { +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->IC_CaptureCallback(htim); +#else HAL_TIM_IC_CaptureCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } /* Output compare event */ else { +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->OC_DelayElapsedCallback(htim); + htim->PWM_PulseFinishedCallback(htim); +#else HAL_TIM_OC_DelayElapsedCallback(htim); HAL_TIM_PWM_PulseFinishedCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; @@ -2717,7 +3351,11 @@ void HAL_TIM_IRQHandler(TIM_HandleTypeDef* htim) if (__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_UPDATE) != RESET) { __HAL_TIM_CLEAR_IT(htim, TIM_IT_UPDATE); +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->PeriodElapsedCallback(htim); +#else HAL_TIM_PeriodElapsedCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } } @@ -2727,7 +3365,11 @@ void HAL_TIM_IRQHandler(TIM_HandleTypeDef* htim) if (__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_BREAK) != RESET) { __HAL_TIM_CLEAR_IT(htim, TIM_IT_BREAK); +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->BreakCallback(htim); +#else HAL_TIMEx_BreakCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } } @@ -2737,7 +3379,11 @@ void HAL_TIM_IRQHandler(TIM_HandleTypeDef* htim) if (__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_TRIGGER) != RESET) { __HAL_TIM_CLEAR_IT(htim, TIM_IT_TRIGGER); +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->TriggerCallback(htim); +#else HAL_TIM_TriggerCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } } @@ -2747,28 +3393,33 @@ void HAL_TIM_IRQHandler(TIM_HandleTypeDef* htim) if (__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_COM) != RESET) { __HAL_TIM_CLEAR_IT(htim, TIM_FLAG_COM); - HAL_TIMEx_CommutationCallback(htim); +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->CommutationCallback(htim); +#else + HAL_TIMEx_CommutCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } } } + /** * @} */ -/** @defgroup TIM_Exported_Functions_Group8 Peripheral Control functions - * @brief Peripheral Control functions - * +/** @defgroup TIM_Exported_Functions_Group8 TIM Peripheral Control functions + * @brief TIM Peripheral Control functions + * @verbatim ============================================================================== ##### Peripheral Control functions ##### ============================================================================== [..] This section provides functions allowing to: - (+) Configure The Input Output channels for OC, PWM, IC or One Pulse mode. - (+) Configure External Clock source. - (+) Configure Complementary channels, break features and dead time. - (+) Configure Master and the Slave synchronization. - (+) Configure the DMA Burst Mode. + (+) Configure The Input Output channels for OC, PWM, IC or One Pulse mode. + (+) Configure External Clock source. + (+) Configure Complementary channels, break features and dead time. + (+) Configure Master and the Slave synchronization. + (+) Configure the DMA Burst Mode. @endverbatim * @{ @@ -2777,10 +3428,9 @@ void HAL_TIM_IRQHandler(TIM_HandleTypeDef* htim) /** * @brief Initializes the TIM Output Compare Channels according to the specified * parameters in the TIM_OC_InitTypeDef. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param sConfig: TIM Output Compare configuration structure - * @param Channel: TIM Channels to be enabled. + * @param htim TIM Output Compare handle + * @param sConfig TIM Output Compare configuration structure + * @param Channel TIM Channels to configure * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -2788,66 +3438,79 @@ void HAL_TIM_IRQHandler(TIM_HandleTypeDef* htim) * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ -HAL_StatusTypeDef HAL_TIM_OC_ConfigChannel(TIM_HandleTypeDef* htim, TIM_OC_InitTypeDef* sConfig, uint32_t Channel) +HAL_StatusTypeDef HAL_TIM_OC_ConfigChannel(TIM_HandleTypeDef* htim, + TIM_OC_InitTypeDef* sConfig, + uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CHANNELS(Channel)); assert_param(IS_TIM_OC_MODE(sConfig->OCMode)); assert_param(IS_TIM_OC_POLARITY(sConfig->OCPolarity)); - /* Check input state */ + + /* Process Locked */ __HAL_LOCK(htim); + htim->State = HAL_TIM_STATE_BUSY; switch (Channel) { case TIM_CHANNEL_1: { + /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); + /* Configure the TIM Channel 1 in Output Compare */ TIM_OC1_SetConfig(htim->Instance, sConfig); + break; } - break; case TIM_CHANNEL_2: { + /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); + /* Configure the TIM Channel 2 in Output Compare */ TIM_OC2_SetConfig(htim->Instance, sConfig); + break; } - break; case TIM_CHANNEL_3: { + /* Check the parameters */ assert_param(IS_TIM_CC3_INSTANCE(htim->Instance)); + /* Configure the TIM Channel 3 in Output Compare */ TIM_OC3_SetConfig(htim->Instance, sConfig); + break; } - break; case TIM_CHANNEL_4: { + /* Check the parameters */ assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); + /* Configure the TIM Channel 4 in Output Compare */ TIM_OC4_SetConfig(htim->Instance, sConfig); + break; } - break; default: break; } htim->State = HAL_TIM_STATE_READY; + __HAL_UNLOCK(htim); + return HAL_OK; } /** * @brief Initializes the TIM Input Capture Channels according to the specified * parameters in the TIM_IC_InitTypeDef. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param sConfig: TIM Input Capture configuration structure - * @param Channel: TIM Channels to be enabled. + * @param htim TIM IC handle + * @param sConfig TIM Input Capture configuration structure + * @param Channel TIM Channel to configure * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -2863,7 +3526,10 @@ HAL_StatusTypeDef HAL_TIM_IC_ConfigChannel(TIM_HandleTypeDef* htim, TIM_IC_InitT assert_param(IS_TIM_IC_SELECTION(sConfig->ICSelection)); assert_param(IS_TIM_IC_PRESCALER(sConfig->ICPrescaler)); assert_param(IS_TIM_IC_FILTER(sConfig->ICFilter)); + + /* Process Locked */ __HAL_LOCK(htim); + htim->State = HAL_TIM_STATE_BUSY; if (Channel == TIM_CHANNEL_1) @@ -2873,8 +3539,10 @@ HAL_StatusTypeDef HAL_TIM_IC_ConfigChannel(TIM_HandleTypeDef* htim, TIM_IC_InitT sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); + /* Reset the IC1PSC Bits */ htim->Instance->CCMR1 &= ~TIM_CCMR1_IC1PSC; + /* Set the IC1PSC value */ htim->Instance->CCMR1 |= sConfig->ICPrescaler; } @@ -2882,12 +3550,15 @@ HAL_StatusTypeDef HAL_TIM_IC_ConfigChannel(TIM_HandleTypeDef* htim, TIM_IC_InitT { /* TI2 Configuration */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); + TIM_TI2_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); + /* Reset the IC2PSC Bits */ htim->Instance->CCMR1 &= ~TIM_CCMR1_IC2PSC; + /* Set the IC2PSC value */ htim->Instance->CCMR1 |= (sConfig->ICPrescaler << 8U); } @@ -2895,12 +3566,15 @@ HAL_StatusTypeDef HAL_TIM_IC_ConfigChannel(TIM_HandleTypeDef* htim, TIM_IC_InitT { /* TI3 Configuration */ assert_param(IS_TIM_CC3_INSTANCE(htim->Instance)); + TIM_TI3_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); + /* Reset the IC3PSC Bits */ htim->Instance->CCMR2 &= ~TIM_CCMR2_IC3PSC; + /* Set the IC3PSC value */ htim->Instance->CCMR2 |= sConfig->ICPrescaler; } @@ -2908,28 +3582,32 @@ HAL_StatusTypeDef HAL_TIM_IC_ConfigChannel(TIM_HandleTypeDef* htim, TIM_IC_InitT { /* TI4 Configuration */ assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); + TIM_TI4_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); + /* Reset the IC4PSC Bits */ htim->Instance->CCMR2 &= ~TIM_CCMR2_IC4PSC; + /* Set the IC4PSC value */ htim->Instance->CCMR2 |= (sConfig->ICPrescaler << 8U); } htim->State = HAL_TIM_STATE_READY; + __HAL_UNLOCK(htim); + return HAL_OK; } /** * @brief Initializes the TIM PWM channels according to the specified * parameters in the TIM_OC_InitTypeDef. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param sConfig: TIM PWM configuration structure - * @param Channel: TIM Channels to be enabled. + * @param htim TIM PWM handle + * @param sConfig TIM PWM configuration structure + * @param Channel TIM Channels to be configured * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -2937,106 +3615,137 @@ HAL_StatusTypeDef HAL_TIM_IC_ConfigChannel(TIM_HandleTypeDef* htim, TIM_IC_InitT * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ -HAL_StatusTypeDef HAL_TIM_PWM_ConfigChannel(TIM_HandleTypeDef* htim, TIM_OC_InitTypeDef* sConfig, uint32_t Channel) +HAL_StatusTypeDef HAL_TIM_PWM_ConfigChannel(TIM_HandleTypeDef* htim, + TIM_OC_InitTypeDef* sConfig, + uint32_t Channel) { - __HAL_LOCK(htim); /* Check the parameters */ assert_param(IS_TIM_CHANNELS(Channel)); assert_param(IS_TIM_PWM_MODE(sConfig->OCMode)); assert_param(IS_TIM_OC_POLARITY(sConfig->OCPolarity)); assert_param(IS_TIM_FAST_STATE(sConfig->OCFastMode)); + + /* Process Locked */ + __HAL_LOCK(htim); + htim->State = HAL_TIM_STATE_BUSY; switch (Channel) { case TIM_CHANNEL_1: { + /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); + /* Configure the Channel 1 in PWM mode */ TIM_OC1_SetConfig(htim->Instance, sConfig); + /* Set the Preload enable bit for channel1 */ htim->Instance->CCMR1 |= TIM_CCMR1_OC1PE; + /* Configure the Output Fast mode */ htim->Instance->CCMR1 &= ~TIM_CCMR1_OC1FE; htim->Instance->CCMR1 |= sConfig->OCFastMode; + break; } - break; case TIM_CHANNEL_2: { + /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); + /* Configure the Channel 2 in PWM mode */ TIM_OC2_SetConfig(htim->Instance, sConfig); + /* Set the Preload enable bit for channel2 */ htim->Instance->CCMR1 |= TIM_CCMR1_OC2PE; + /* Configure the Output Fast mode */ htim->Instance->CCMR1 &= ~TIM_CCMR1_OC2FE; htim->Instance->CCMR1 |= sConfig->OCFastMode << 8U; + break; } - break; case TIM_CHANNEL_3: { + /* Check the parameters */ assert_param(IS_TIM_CC3_INSTANCE(htim->Instance)); + /* Configure the Channel 3 in PWM mode */ TIM_OC3_SetConfig(htim->Instance, sConfig); + /* Set the Preload enable bit for channel3 */ htim->Instance->CCMR2 |= TIM_CCMR2_OC3PE; + /* Configure the Output Fast mode */ htim->Instance->CCMR2 &= ~TIM_CCMR2_OC3FE; htim->Instance->CCMR2 |= sConfig->OCFastMode; + break; } - break; case TIM_CHANNEL_4: { + /* Check the parameters */ assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); + /* Configure the Channel 4 in PWM mode */ TIM_OC4_SetConfig(htim->Instance, sConfig); + /* Set the Preload enable bit for channel4 */ htim->Instance->CCMR2 |= TIM_CCMR2_OC4PE; + /* Configure the Output Fast mode */ htim->Instance->CCMR2 &= ~TIM_CCMR2_OC4FE; htim->Instance->CCMR2 |= sConfig->OCFastMode << 8U; + break; } - break; default: break; } htim->State = HAL_TIM_STATE_READY; + __HAL_UNLOCK(htim); + return HAL_OK; } /** * @brief Initializes the TIM One Pulse Channels according to the specified * parameters in the TIM_OnePulse_InitTypeDef. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param sConfig: TIM One Pulse configuration structure - * @param OutputChannel: TIM Channels to be enabled. + * @param htim TIM One Pulse handle + * @param sConfig TIM One Pulse configuration structure + * @param OutputChannel TIM output channel to configure * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @param InputChannel: TIM Channels to be enabled. + * @param InputChannel TIM input Channel to configure * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected + * @note To output a waveform with a minimum delay user can enable the fast + * mode by calling the @ref __HAL_TIM_ENABLE_OCxFAST macro. Then CCx + * output is forced in response to the edge detection on TIx input, + * without taking in account the comparison. * @retval HAL status */ -HAL_StatusTypeDef HAL_TIM_OnePulse_ConfigChannel(TIM_HandleTypeDef* htim, TIM_OnePulse_InitTypeDef* sConfig, uint32_t OutputChannel, uint32_t InputChannel) +HAL_StatusTypeDef HAL_TIM_OnePulse_ConfigChannel(TIM_HandleTypeDef* htim, TIM_OnePulse_InitTypeDef* sConfig, + uint32_t OutputChannel, uint32_t InputChannel) { TIM_OC_InitTypeDef temp1; + /* Check the parameters */ assert_param(IS_TIM_OPM_CHANNELS(OutputChannel)); assert_param(IS_TIM_OPM_CHANNELS(InputChannel)); if (OutputChannel != InputChannel) { + /* Process Locked */ __HAL_LOCK(htim); + htim->State = HAL_TIM_STATE_BUSY; + /* Extract the Output compare configuration from sConfig structure */ temp1.OCMode = sConfig->OCMode; temp1.Pulse = sConfig->Pulse; @@ -3050,16 +3759,18 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_ConfigChannel(TIM_HandleTypeDef* htim, TIM_O case TIM_CHANNEL_1: { assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); + TIM_OC1_SetConfig(htim->Instance, &temp1); + break; } - break; case TIM_CHANNEL_2: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); + TIM_OC2_SetConfig(htim->Instance, &temp1); + break; } - break; default: break; @@ -3070,41 +3781,51 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_ConfigChannel(TIM_HandleTypeDef* htim, TIM_O case TIM_CHANNEL_1: { assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); + TIM_TI1_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); + /* Reset the IC1PSC Bits */ htim->Instance->CCMR1 &= ~TIM_CCMR1_IC1PSC; + /* Select the Trigger source */ htim->Instance->SMCR &= ~TIM_SMCR_TS; htim->Instance->SMCR |= TIM_TS_TI1FP1; + /* Select the Slave Mode */ htim->Instance->SMCR &= ~TIM_SMCR_SMS; htim->Instance->SMCR |= TIM_SLAVEMODE_TRIGGER; + break; } - break; case TIM_CHANNEL_2: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); + TIM_TI2_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); + /* Reset the IC2PSC Bits */ htim->Instance->CCMR1 &= ~TIM_CCMR1_IC2PSC; + /* Select the Trigger source */ htim->Instance->SMCR &= ~TIM_SMCR_TS; htim->Instance->SMCR |= TIM_TS_TI2FP2; + /* Select the Slave Mode */ htim->Instance->SMCR &= ~TIM_SMCR_SMS; htim->Instance->SMCR |= TIM_SLAVEMODE_TRIGGER; + break; } - break; default: break; } htim->State = HAL_TIM_STATE_READY; + __HAL_UNLOCK(htim); + return HAL_OK; } else @@ -3115,10 +3836,9 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_ConfigChannel(TIM_HandleTypeDef* htim, TIM_O /** * @brief Configure the DMA Burst to transfer Data from the memory to the TIM peripheral - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param BurstBaseAddress: TIM Base address from when the DMA will starts the Data write. - * This parameters can be on of the following values: + * @param htim TIM handle + * @param BurstBaseAddress TIM Base address from where the DMA will start the Data write + * This parameter can be one of the following values: * @arg TIM_DMABASE_CR1 * @arg TIM_DMABASE_CR2 * @arg TIM_DMABASE_SMCR @@ -3137,9 +3857,8 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_ConfigChannel(TIM_HandleTypeDef* htim, TIM_O * @arg TIM_DMABASE_CCR3 * @arg TIM_DMABASE_CCR4 * @arg TIM_DMABASE_BDTR - * @arg TIM_DMABASE_DCR - * @param BurstRequestSrc: TIM DMA Request sources. - * This parameters can be on of the following values: + * @param BurstRequestSrc TIM DMA Request sources + * This parameter can be one of the following values: * @arg TIM_DMA_UPDATE: TIM update Interrupt source * @arg TIM_DMA_CC1: TIM Capture Compare 1 DMA source * @arg TIM_DMA_CC2: TIM Capture Compare 2 DMA source @@ -3147,9 +3866,10 @@ HAL_StatusTypeDef HAL_TIM_OnePulse_ConfigChannel(TIM_HandleTypeDef* htim, TIM_O * @arg TIM_DMA_CC4: TIM Capture Compare 4 DMA source * @arg TIM_DMA_COM: TIM Commutation DMA source * @arg TIM_DMA_TRIGGER: TIM Trigger DMA source - * @param BurstBuffer: The Buffer address. - * @param BurstLength: DMA Burst length. This parameter can be one value - * between TIM_DMABURSTLENGTH_1TRANSFER and TIM_DMABURSTLENGTH_18TRANSFERS. + * @param BurstBuffer The Buffer address. + * @param BurstLength DMA Burst length. This parameter can be one value + * between: TIM_DMABURSTLENGTH_1TRANSFER and TIM_DMABURSTLENGTH_18TRANSFERS. + * @note This function should be used only when BurstLength is equal to DMA data transfer length. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStart(TIM_HandleTypeDef* htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc, @@ -3161,13 +3881,13 @@ HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStart(TIM_HandleTypeDef* htim, uint32_t assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc)); assert_param(IS_TIM_DMA_LENGTH(BurstLength)); - if ((htim->State == HAL_TIM_STATE_BUSY)) + if (htim->State == HAL_TIM_STATE_BUSY) { return HAL_BUSY; } - else if ((htim->State == HAL_TIM_STATE_READY)) + else if (htim->State == HAL_TIM_STATE_READY) { - if ((BurstBuffer == 0U) && (BurstLength > 0U)) + if ((BurstBuffer == NULL) && (BurstLength > 0U)) { return HAL_ERROR; } @@ -3176,108 +3896,170 @@ HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStart(TIM_HandleTypeDef* htim, uint32_t htim->State = HAL_TIM_STATE_BUSY; } } + else + { + /* nothing to do */ + } switch (BurstRequestSrc) { case TIM_DMA_UPDATE: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA Period elapsed callbacks */ htim->hdma[TIM_DMA_ID_UPDATE]->XferCpltCallback = TIM_DMAPeriodElapsedCplt; + htim->hdma[TIM_DMA_ID_UPDATE]->XferHalfCpltCallback = TIM_DMAPeriodElapsedHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_UPDATE]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U) != HAL_OK) + { + return HAL_ERROR; + } + + break; } - break; case TIM_DMA_CC1: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)BurstBuffer, + (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U) != HAL_OK) + { + return HAL_ERROR; + } + + break; } - break; case TIM_DMA_CC2: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC2]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)BurstBuffer, + (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U) != HAL_OK) + { + return HAL_ERROR; + } + + break; } - break; case TIM_DMA_CC3: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC3]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)BurstBuffer, + (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U) != HAL_OK) + { + return HAL_ERROR; + } + + break; } - break; case TIM_DMA_CC4: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC4]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)BurstBuffer, + (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U) != HAL_OK) + { + return HAL_ERROR; + } + + break; } - break; case TIM_DMA_COM: { - /* Set the DMA Period elapsed callback */ - htim->hdma[TIM_DMA_ID_COMMUTATION]->XferCpltCallback = TIMEx_DMACommutationCplt; + /* Set the DMA commutation callbacks */ + htim->hdma[TIM_DMA_ID_COMMUTATION]->XferCpltCallback = TIMEx_DMACommutationCplt; + htim->hdma[TIM_DMA_ID_COMMUTATION]->XferHalfCpltCallback = TIMEx_DMACommutationHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_COMMUTATION], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_COMMUTATION], (uint32_t)BurstBuffer, + (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U) != HAL_OK) + { + return HAL_ERROR; + } + + break; } - break; case TIM_DMA_TRIGGER: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA trigger callbacks */ htim->hdma[TIM_DMA_ID_TRIGGER]->XferCpltCallback = TIM_DMATriggerCplt; + htim->hdma[TIM_DMA_ID_TRIGGER]->XferHalfCpltCallback = TIM_DMATriggerHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_TRIGGER]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_TRIGGER], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_TRIGGER], (uint32_t)BurstBuffer, + (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U) != HAL_OK) + { + return HAL_ERROR; + } + + break; } - break; default: break; } /* configure the DMA Burst Mode */ - htim->Instance->DCR = BurstBaseAddress | BurstLength; + htim->Instance->DCR = (BurstBaseAddress | BurstLength); + /* Enable the TIM DMA Request */ __HAL_TIM_ENABLE_DMA(htim, BurstRequestSrc); + htim->State = HAL_TIM_STATE_READY; + /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM DMA Burst mode - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param BurstRequestSrc: TIM DMA Request sources to disable + * @param htim TIM handle + * @param BurstRequestSrc TIM DMA Request sources to disable * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStop(TIM_HandleTypeDef* htim, uint32_t BurstRequestSrc) { + HAL_StatusTypeDef status = HAL_OK; /* Check the parameters */ assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc)); @@ -3286,62 +4068,65 @@ HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStop(TIM_HandleTypeDef* htim, uint32_t B { case TIM_DMA_UPDATE: { - HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_UPDATE]); + status = HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_UPDATE]); + break; } - break; case TIM_DMA_CC1: { - HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC1]); + status = HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]); + break; } - break; case TIM_DMA_CC2: { - HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC2]); + status = HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC2]); + break; } - break; case TIM_DMA_CC3: { - HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC3]); + status = HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC3]); + break; } - break; case TIM_DMA_CC4: { - HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC4]); + status = HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC4]); + break; } - break; case TIM_DMA_COM: { - HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_COMMUTATION]); + status = HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_COMMUTATION]); + break; } - break; case TIM_DMA_TRIGGER: { - HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_TRIGGER]); + status = HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_TRIGGER]); + break; } - break; default: break; } - /* Disable the TIM Update DMA request */ - __HAL_TIM_DISABLE_DMA(htim, BurstRequestSrc); + if (HAL_OK == status) + { + /* Disable the TIM Update DMA request */ + __HAL_TIM_DISABLE_DMA(htim, BurstRequestSrc); + } + /* Return function status */ - return HAL_OK; + return status; } /** * @brief Configure the DMA Burst to transfer Data from the TIM peripheral to the memory - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param BurstBaseAddress: TIM Base address from when the DMA will starts the Data read. - * This parameters can be on of the following values: + * @param htim TIM handle + * @param BurstBaseAddress TIM Base address from where the DMA will start the Data read + * This parameter can be one of the following values: * @arg TIM_DMABASE_CR1 * @arg TIM_DMABASE_CR2 * @arg TIM_DMABASE_SMCR @@ -3360,9 +4145,8 @@ HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStop(TIM_HandleTypeDef* htim, uint32_t B * @arg TIM_DMABASE_CCR3 * @arg TIM_DMABASE_CCR4 * @arg TIM_DMABASE_BDTR - * @arg TIM_DMABASE_DCR - * @param BurstRequestSrc: TIM DMA Request sources. - * This parameters can be on of the following values: + * @param BurstRequestSrc TIM DMA Request sources + * This parameter can be one of the following values: * @arg TIM_DMA_UPDATE: TIM update Interrupt source * @arg TIM_DMA_CC1: TIM Capture Compare 1 DMA source * @arg TIM_DMA_CC2: TIM Capture Compare 2 DMA source @@ -3370,13 +4154,14 @@ HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStop(TIM_HandleTypeDef* htim, uint32_t B * @arg TIM_DMA_CC4: TIM Capture Compare 4 DMA source * @arg TIM_DMA_COM: TIM Commutation DMA source * @arg TIM_DMA_TRIGGER: TIM Trigger DMA source - * @param BurstBuffer: The Buffer address. - * @param BurstLength: DMA Burst length. This parameter can be one value - * between TIM_DMABURSTLENGTH_1TRANSFER and TIM_DMABURSTLENGTH_18TRANSFERS. + * @param BurstBuffer The Buffer address. + * @param BurstLength DMA Burst length. This parameter can be one value + * between: TIM_DMABURSTLENGTH_1TRANSFER and TIM_DMABURSTLENGTH_18TRANSFERS. + * @note This function should be used only when BurstLength is equal to DMA data transfer length. * @retval HAL status */ -HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStart(TIM_HandleTypeDef* htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc, - uint32_t* BurstBuffer, uint32_t BurstLength) +HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStart(TIM_HandleTypeDef* htim, uint32_t BurstBaseAddress, + uint32_t BurstRequestSrc, uint32_t* BurstBuffer, uint32_t BurstLength) { /* Check the parameters */ assert_param(IS_TIM_DMABURST_INSTANCE(htim->Instance)); @@ -3384,13 +4169,13 @@ HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStart(TIM_HandleTypeDef* htim, uint32_t B assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc)); assert_param(IS_TIM_DMA_LENGTH(BurstLength)); - if ((htim->State == HAL_TIM_STATE_BUSY)) + if (htim->State == HAL_TIM_STATE_BUSY) { return HAL_BUSY; } - else if ((htim->State == HAL_TIM_STATE_READY)) + else if (htim->State == HAL_TIM_STATE_READY) { - if ((BurstBuffer == 0U) && (BurstLength > 0U)) + if ((BurstBuffer == NULL) && (BurstLength > 0U)) { return HAL_ERROR; } @@ -3399,108 +4184,164 @@ HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStart(TIM_HandleTypeDef* htim, uint32_t B htim->State = HAL_TIM_STATE_BUSY; } } + else + { + /* nothing to do */ + } switch (BurstRequestSrc) { case TIM_DMA_UPDATE: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA Period elapsed callbacks */ htim->hdma[TIM_DMA_ID_UPDATE]->XferCpltCallback = TIM_DMAPeriodElapsedCplt; + htim->hdma[TIM_DMA_ID_UPDATE]->XferHalfCpltCallback = TIM_DMAPeriodElapsedHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_UPDATE]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U) != HAL_OK) + { + return HAL_ERROR; + } + + break; } - break; case TIM_DMA_CC1: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA capture callbacks */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt; + htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMACaptureHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U) != HAL_OK) + { + return HAL_ERROR; + } + + break; } - break; case TIM_DMA_CC2: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA capture/compare callbacks */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt; + htim->hdma[TIM_DMA_ID_CC2]->XferHalfCpltCallback = TIM_DMACaptureHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U) != HAL_OK) + { + return HAL_ERROR; + } + + break; } - break; case TIM_DMA_CC3: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA capture callbacks */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMACaptureCplt; + htim->hdma[TIM_DMA_ID_CC3]->XferHalfCpltCallback = TIM_DMACaptureHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U) != HAL_OK) + { + return HAL_ERROR; + } + + break; } - break; case TIM_DMA_CC4: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA capture callbacks */ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMACaptureCplt; + htim->hdma[TIM_DMA_ID_CC4]->XferHalfCpltCallback = TIM_DMACaptureHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U) != HAL_OK) + { + return HAL_ERROR; + } + + break; } - break; case TIM_DMA_COM: { - /* Set the DMA Period elapsed callback */ - htim->hdma[TIM_DMA_ID_COMMUTATION]->XferCpltCallback = TIMEx_DMACommutationCplt; + /* Set the DMA commutation callbacks */ + htim->hdma[TIM_DMA_ID_COMMUTATION]->XferCpltCallback = TIMEx_DMACommutationCplt; + htim->hdma[TIM_DMA_ID_COMMUTATION]->XferHalfCpltCallback = TIMEx_DMACommutationHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_COMMUTATION], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_COMMUTATION], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U) != HAL_OK) + { + return HAL_ERROR; + } + + break; } - break; case TIM_DMA_TRIGGER: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA trigger callbacks */ htim->hdma[TIM_DMA_ID_TRIGGER]->XferCpltCallback = TIM_DMATriggerCplt; + htim->hdma[TIM_DMA_ID_TRIGGER]->XferHalfCpltCallback = TIM_DMATriggerHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_TRIGGER]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_TRIGGER], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_TRIGGER], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U) != HAL_OK) + { + return HAL_ERROR; + } + + break; } - break; default: break; } /* configure the DMA Burst Mode */ - htim->Instance->DCR = BurstBaseAddress | BurstLength; + htim->Instance->DCR = (BurstBaseAddress | BurstLength); + /* Enable the TIM DMA Request */ __HAL_TIM_ENABLE_DMA(htim, BurstRequestSrc); + htim->State = HAL_TIM_STATE_READY; + /* Return function status */ return HAL_OK; } /** * @brief Stop the DMA burst reading - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param BurstRequestSrc: TIM DMA Request sources to disable. + * @param htim TIM handle + * @param BurstRequestSrc TIM DMA Request sources to disable. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStop(TIM_HandleTypeDef* htim, uint32_t BurstRequestSrc) { + HAL_StatusTypeDef status = HAL_OK; /* Check the parameters */ assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc)); @@ -3509,61 +4350,64 @@ HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStop(TIM_HandleTypeDef* htim, uint32_t Bu { case TIM_DMA_UPDATE: { - HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_UPDATE]); + status = HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_UPDATE]); + break; } - break; case TIM_DMA_CC1: { - HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC1]); + status = HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]); + break; } - break; case TIM_DMA_CC2: { - HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC2]); + status = HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC2]); + break; } - break; case TIM_DMA_CC3: { - HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC3]); + status = HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC3]); + break; } - break; case TIM_DMA_CC4: { - HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC4]); + status = HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC4]); + break; } - break; case TIM_DMA_COM: { - HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_COMMUTATION]); + status = HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_COMMUTATION]); + break; } - break; case TIM_DMA_TRIGGER: { - HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_TRIGGER]); + status = HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_TRIGGER]); + break; } - break; default: break; } - /* Disable the TIM Update DMA request */ - __HAL_TIM_DISABLE_DMA(htim, BurstRequestSrc); - /* Return function status */ - return HAL_OK; + if (HAL_OK == status) + { + /* Disable the TIM Update DMA request */ + __HAL_TIM_DISABLE_DMA(htim, BurstRequestSrc); + } + + /* Return function status */ + return status; } /** * @brief Generate a software event - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param EventSource: specifies the event source. + * @param htim TIM handle + * @param EventSource specifies the event source. * This parameter can be one of the following values: * @arg TIM_EVENTSOURCE_UPDATE: Timer update Event source * @arg TIM_EVENTSOURCE_CC1: Timer Capture Compare 1 Event source @@ -3573,8 +4417,10 @@ HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStop(TIM_HandleTypeDef* htim, uint32_t Bu * @arg TIM_EVENTSOURCE_COM: Timer COM event source * @arg TIM_EVENTSOURCE_TRIGGER: Timer Trigger Event source * @arg TIM_EVENTSOURCE_BREAK: Timer Break event source - * @note TIM6 and TIM7 can only generate an update event. - * @note TIM_EVENTSOURCE_COM and TIM_EVENTSOURCE_BREAK are used only with TIM1 and TIM8. + * @note Basic timers can only generate an update event. + * @note TIM_EVENTSOURCE_COM is relevant only with advanced timer instances. + * @note TIM_EVENTSOURCE_BREAK are relevant only for timer instances + * supporting a break input. * @retval HAL status */ @@ -3583,147 +4429,182 @@ HAL_StatusTypeDef HAL_TIM_GenerateEvent(TIM_HandleTypeDef* htim, uint32_t EventS /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_EVENT_SOURCE(EventSource)); + /* Process Locked */ __HAL_LOCK(htim); + /* Change the TIM state */ htim->State = HAL_TIM_STATE_BUSY; + /* Set the event sources */ htim->Instance->EGR = EventSource; + /* Change the TIM state */ htim->State = HAL_TIM_STATE_READY; + __HAL_UNLOCK(htim); + /* Return function status */ return HAL_OK; } /** * @brief Configures the OCRef clear feature - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param sClearInputConfig: pointer to a TIM_ClearInputConfigTypeDef structure that + * @param htim TIM handle + * @param sClearInputConfig pointer to a TIM_ClearInputConfigTypeDef structure that * contains the OCREF clear feature and parameters for the TIM peripheral. - * @param Channel: specifies the TIM Channel. + * @param Channel specifies the TIM Channel * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected + * @arg TIM_CHANNEL_1: TIM Channel 1 + * @arg TIM_CHANNEL_2: TIM Channel 2 + * @arg TIM_CHANNEL_3: TIM Channel 3 + * @arg TIM_CHANNEL_4: TIM Channel 4 * @retval HAL status */ -HAL_StatusTypeDef HAL_TIM_ConfigOCrefClear(TIM_HandleTypeDef* htim, TIM_ClearInputConfigTypeDef* sClearInputConfig, uint32_t Channel) +HAL_StatusTypeDef HAL_TIM_ConfigOCrefClear(TIM_HandleTypeDef* htim, + TIM_ClearInputConfigTypeDef* sClearInputConfig, + uint32_t Channel) { /* Check the parameters */ - assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); - assert_param(IS_TIM_CHANNELS(Channel)); + assert_param(IS_TIM_OCXREF_CLEAR_INSTANCE(htim->Instance)); assert_param(IS_TIM_CLEARINPUT_SOURCE(sClearInputConfig->ClearInputSource)); - assert_param(IS_TIM_CLEARINPUT_POLARITY(sClearInputConfig->ClearInputPolarity)); - assert_param(IS_TIM_CLEARINPUT_PRESCALER(sClearInputConfig->ClearInputPrescaler)); - assert_param(IS_TIM_CLEARINPUT_FILTER(sClearInputConfig->ClearInputFilter)); + /* Process Locked */ __HAL_LOCK(htim); + htim->State = HAL_TIM_STATE_BUSY; - if (sClearInputConfig->ClearInputSource == TIM_CLEARINPUTSOURCE_ETR) + switch (sClearInputConfig->ClearInputSource) { - TIM_ETR_SetConfig(htim->Instance, - sClearInputConfig->ClearInputPrescaler, - sClearInputConfig->ClearInputPolarity, - sClearInputConfig->ClearInputFilter); + case TIM_CLEARINPUTSOURCE_NONE: + { + /* Clear the OCREF clear selection bit and the the ETR Bits */ + CLEAR_BIT(htim->Instance->SMCR, (TIM_SMCR_ETF | TIM_SMCR_ETPS | TIM_SMCR_ECE | TIM_SMCR_ETP)); + break; + } + + case TIM_CLEARINPUTSOURCE_ETR: + { + /* Check the parameters */ + assert_param(IS_TIM_CLEARINPUT_POLARITY(sClearInputConfig->ClearInputPolarity)); + assert_param(IS_TIM_CLEARINPUT_PRESCALER(sClearInputConfig->ClearInputPrescaler)); + assert_param(IS_TIM_CLEARINPUT_FILTER(sClearInputConfig->ClearInputFilter)); + + /* When OCRef clear feature is used with ETR source, ETR prescaler must be off */ + if (sClearInputConfig->ClearInputPrescaler != TIM_CLEARINPUTPRESCALER_DIV1) + { + htim->State = HAL_TIM_STATE_READY; + __HAL_UNLOCK(htim); + return HAL_ERROR; + } + + TIM_ETR_SetConfig(htim->Instance, + sClearInputConfig->ClearInputPrescaler, + sClearInputConfig->ClearInputPolarity, + sClearInputConfig->ClearInputFilter); + break; + } + + default: + break; } switch (Channel) { case TIM_CHANNEL_1: { - if (sClearInputConfig->ClearInputState != RESET) + if (sClearInputConfig->ClearInputState != (uint32_t)DISABLE) { - /* Enable the Ocref clear feature for Channel 1 */ - htim->Instance->CCMR1 |= TIM_CCMR1_OC1CE; + /* Enable the OCREF clear feature for Channel 1 */ + SET_BIT(htim->Instance->CCMR1, TIM_CCMR1_OC1CE); } else { - /* Disable the Ocref clear feature for Channel 1 */ - htim->Instance->CCMR1 &= ~TIM_CCMR1_OC1CE; + /* Disable the OCREF clear feature for Channel 1 */ + CLEAR_BIT(htim->Instance->CCMR1, TIM_CCMR1_OC1CE); } + + break; } - break; case TIM_CHANNEL_2: { - assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); - - if (sClearInputConfig->ClearInputState != RESET) + if (sClearInputConfig->ClearInputState != (uint32_t)DISABLE) { - /* Enable the Ocref clear feature for Channel 2 */ - htim->Instance->CCMR1 |= TIM_CCMR1_OC2CE; + /* Enable the OCREF clear feature for Channel 2 */ + SET_BIT(htim->Instance->CCMR1, TIM_CCMR1_OC2CE); } else { - /* Disable the Ocref clear feature for Channel 2 */ - htim->Instance->CCMR1 &= ~TIM_CCMR1_OC2CE; + /* Disable the OCREF clear feature for Channel 2 */ + CLEAR_BIT(htim->Instance->CCMR1, TIM_CCMR1_OC2CE); } + + break; } - break; case TIM_CHANNEL_3: { - assert_param(IS_TIM_CC3_INSTANCE(htim->Instance)); - - if (sClearInputConfig->ClearInputState != RESET) + if (sClearInputConfig->ClearInputState != (uint32_t)DISABLE) { - /* Enable the Ocref clear feature for Channel 3 */ - htim->Instance->CCMR2 |= TIM_CCMR2_OC3CE; + /* Enable the OCREF clear feature for Channel 3 */ + SET_BIT(htim->Instance->CCMR2, TIM_CCMR2_OC3CE); } else { - /* Disable the Ocref clear feature for Channel 3 */ - htim->Instance->CCMR2 &= ~TIM_CCMR2_OC3CE; + /* Disable the OCREF clear feature for Channel 3 */ + CLEAR_BIT(htim->Instance->CCMR2, TIM_CCMR2_OC3CE); } + + break; } - break; case TIM_CHANNEL_4: { - assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); - - if (sClearInputConfig->ClearInputState != RESET) + if (sClearInputConfig->ClearInputState != (uint32_t)DISABLE) { - /* Enable the Ocref clear feature for Channel 4 */ - htim->Instance->CCMR2 |= TIM_CCMR2_OC4CE; + /* Enable the OCREF clear feature for Channel 4 */ + SET_BIT(htim->Instance->CCMR2, TIM_CCMR2_OC4CE); } else { - /* Disable the Ocref clear feature for Channel 4 */ - htim->Instance->CCMR2 &= ~TIM_CCMR2_OC4CE; + /* Disable the OCREF clear feature for Channel 4 */ + CLEAR_BIT(htim->Instance->CCMR2, TIM_CCMR2_OC4CE); } + + break; } - break; default: break; } htim->State = HAL_TIM_STATE_READY; + __HAL_UNLOCK(htim); + return HAL_OK; } /** * @brief Configures the clock source to be used - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param sClockSourceConfig: pointer to a TIM_ClockConfigTypeDef structure that + * @param htim TIM handle + * @param sClockSourceConfig pointer to a TIM_ClockConfigTypeDef structure that * contains the clock source information for the TIM peripheral. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_ConfigClockSource(TIM_HandleTypeDef* htim, TIM_ClockConfigTypeDef* sClockSourceConfig) { - uint32_t tmpsmcr = 0U; + uint32_t tmpsmcr; + /* Process Locked */ __HAL_LOCK(htim); + htim->State = HAL_TIM_STATE_BUSY; + /* Check the parameters */ assert_param(IS_TIM_CLOCKSOURCE(sClockSourceConfig->ClockSource)); + /* Reset the SMS, TS, ECE, ETPS and ETRF bits */ tmpsmcr = htim->Instance->SMCR; tmpsmcr &= ~(TIM_SMCR_SMS | TIM_SMCR_TS); @@ -3735,39 +4616,43 @@ HAL_StatusTypeDef HAL_TIM_ConfigClockSource(TIM_HandleTypeDef* htim, TIM_ClockCo case TIM_CLOCKSOURCE_INTERNAL: { assert_param(IS_TIM_INSTANCE(htim->Instance)); - /* Disable slave mode to clock the prescaler directly with the internal clock */ - htim->Instance->SMCR &= ~TIM_SMCR_SMS; + break; } - break; case TIM_CLOCKSOURCE_ETRMODE1: { - assert_param(IS_TIM_ETR_INSTANCE(htim->Instance)); - assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); + /* Check whether or not the timer instance supports external trigger input mode 1 (ETRF)*/ + assert_param(IS_TIM_CLOCKSOURCE_ETRMODE1_INSTANCE(htim->Instance)); + + /* Check ETR input conditioning related parameters */ assert_param(IS_TIM_CLOCKPRESCALER(sClockSourceConfig->ClockPrescaler)); + assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter)); + /* Configure the ETR Clock source */ TIM_ETR_SetConfig(htim->Instance, sClockSourceConfig->ClockPrescaler, sClockSourceConfig->ClockPolarity, sClockSourceConfig->ClockFilter); - /* Get the TIMx SMCR register value */ - tmpsmcr = htim->Instance->SMCR; - /* Reset the SMS and TS Bits */ - tmpsmcr &= ~(TIM_SMCR_SMS | TIM_SMCR_TS); + /* Select the External clock mode1 and the ETRF trigger */ + tmpsmcr = htim->Instance->SMCR; tmpsmcr |= (TIM_SLAVEMODE_EXTERNAL1 | TIM_CLOCKSOURCE_ETRMODE1); /* Write to TIMx SMCR */ htim->Instance->SMCR = tmpsmcr; + break; } - break; case TIM_CLOCKSOURCE_ETRMODE2: { - assert_param(IS_TIM_ETR_INSTANCE(htim->Instance)); - assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); + /* Check whether or not the timer instance supports external trigger input mode 2 (ETRF)*/ + assert_param(IS_TIM_CLOCKSOURCE_ETRMODE2_INSTANCE(htim->Instance)); + + /* Check ETR input conditioning related parameters */ assert_param(IS_TIM_CLOCKPRESCALER(sClockSourceConfig->ClockPrescaler)); + assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter)); + /* Configure the ETR Clock source */ TIM_ETR_SetConfig(htim->Instance, sClockSourceConfig->ClockPrescaler, @@ -3775,93 +4660,87 @@ HAL_StatusTypeDef HAL_TIM_ConfigClockSource(TIM_HandleTypeDef* htim, TIM_ClockCo sClockSourceConfig->ClockFilter); /* Enable the External clock mode2 */ htim->Instance->SMCR |= TIM_SMCR_ECE; + break; } - break; case TIM_CLOCKSOURCE_TI1: { - assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); + /* Check whether or not the timer instance supports external clock mode 1 */ + assert_param(IS_TIM_CLOCKSOURCE_TIX_INSTANCE(htim->Instance)); + /* Check TI1 input conditioning related parameters */ assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter)); + TIM_TI1_ConfigInputStage(htim->Instance, sClockSourceConfig->ClockPolarity, sClockSourceConfig->ClockFilter); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_TI1); + break; } - break; case TIM_CLOCKSOURCE_TI2: { - assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); - /* Check TI1 input conditioning related parameters */ + /* Check whether or not the timer instance supports external clock mode 1 (ETRF)*/ + assert_param(IS_TIM_CLOCKSOURCE_TIX_INSTANCE(htim->Instance)); + + /* Check TI2 input conditioning related parameters */ assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter)); + TIM_TI2_ConfigInputStage(htim->Instance, sClockSourceConfig->ClockPolarity, sClockSourceConfig->ClockFilter); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_TI2); + break; } - break; case TIM_CLOCKSOURCE_TI1ED: { - assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); + /* Check whether or not the timer instance supports external clock mode 1 */ + assert_param(IS_TIM_CLOCKSOURCE_TIX_INSTANCE(htim->Instance)); + /* Check TI1 input conditioning related parameters */ assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter)); + TIM_TI1_ConfigInputStage(htim->Instance, sClockSourceConfig->ClockPolarity, sClockSourceConfig->ClockFilter); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_TI1ED); + break; } - break; case TIM_CLOCKSOURCE_ITR0: - { - assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); - TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR0); - } - break; - case TIM_CLOCKSOURCE_ITR1: - { - assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); - TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR1); - } - break; - case TIM_CLOCKSOURCE_ITR2: - { - assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); - TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR2); - } - break; - case TIM_CLOCKSOURCE_ITR3: { - assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); - TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR3); + /* Check whether or not the timer instance supports internal trigger input */ + assert_param(IS_TIM_CLOCKSOURCE_ITRX_INSTANCE(htim->Instance)); + + TIM_ITRx_SetConfig(htim->Instance, sClockSourceConfig->ClockSource); + break; } - break; default: break; } htim->State = HAL_TIM_STATE_READY; + __HAL_UNLOCK(htim); + return HAL_OK; } /** * @brief Selects the signal connected to the TI1 input: direct from CH1_input * or a XOR combination between CH1_input, CH2_input & CH3_input - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param TI1_Selection: Indicate whether or not channel 1 is connected to the + * @param htim TIM handle. + * @param TI1_Selection Indicate whether or not channel 1 is connected to the * output of a XOR gate. - * This parameter can be one of the following values: + * This parameter can be one of the following values: * @arg TIM_TI1SELECTION_CH1: The TIMx_CH1 pin is connected to TI1 input * @arg TIM_TI1SELECTION_XORCOMBINATION: The TIMx_CH1, CH2 and CH3 * pins are connected to the TI1 input (XOR combination) @@ -3869,82 +4748,112 @@ HAL_StatusTypeDef HAL_TIM_ConfigClockSource(TIM_HandleTypeDef* htim, TIM_ClockCo */ HAL_StatusTypeDef HAL_TIM_ConfigTI1Input(TIM_HandleTypeDef* htim, uint32_t TI1_Selection) { - uint32_t tmpcr2 = 0U; + uint32_t tmpcr2; + /* Check the parameters */ assert_param(IS_TIM_XOR_INSTANCE(htim->Instance)); assert_param(IS_TIM_TI1SELECTION(TI1_Selection)); + /* Get the TIMx CR2 register value */ tmpcr2 = htim->Instance->CR2; + /* Reset the TI1 selection */ tmpcr2 &= ~TIM_CR2_TI1S; + /* Set the TI1 selection */ tmpcr2 |= TI1_Selection; + /* Write to TIMxCR2 */ htim->Instance->CR2 = tmpcr2; + return HAL_OK; } /** * @brief Configures the TIM in Slave mode - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param sSlaveConfig: pointer to a TIM_SlaveConfigTypeDef structure that + * @param htim TIM handle. + * @param sSlaveConfig pointer to a TIM_SlaveConfigTypeDef structure that * contains the selected trigger (internal trigger input, filtered - * timer input or external trigger input) and the ) and the Slave - * mode (Disable, Reset, Gated, Trigger, External clock mode 1). + * timer input or external trigger input) and the Slave mode + * (Disable, Reset, Gated, Trigger, External clock mode 1). * @retval HAL status */ -HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchronization(TIM_HandleTypeDef* htim, TIM_SlaveConfigTypeDef* sSlaveConfig) +HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchro(TIM_HandleTypeDef* htim, TIM_SlaveConfigTypeDef* sSlaveConfig) { /* Check the parameters */ assert_param(IS_TIM_SLAVE_INSTANCE(htim->Instance)); assert_param(IS_TIM_SLAVE_MODE(sSlaveConfig->SlaveMode)); assert_param(IS_TIM_TRIGGER_SELECTION(sSlaveConfig->InputTrigger)); + __HAL_LOCK(htim); + htim->State = HAL_TIM_STATE_BUSY; - TIM_SlaveTimer_SetConfig(htim, sSlaveConfig); + + if (TIM_SlaveTimer_SetConfig(htim, sSlaveConfig) != HAL_OK) + { + htim->State = HAL_TIM_STATE_READY; + __HAL_UNLOCK(htim); + return HAL_ERROR; + } + /* Disable Trigger Interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_TRIGGER); + /* Disable Trigger DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_TRIGGER); + htim->State = HAL_TIM_STATE_READY; + __HAL_UNLOCK(htim); + return HAL_OK; } /** * @brief Configures the TIM in Slave mode in interrupt mode - * @param htim: TIM handle. - * @param sSlaveConfig: pointer to a TIM_SlaveConfigTypeDef structure that + * @param htim TIM handle. + * @param sSlaveConfig pointer to a TIM_SlaveConfigTypeDef structure that * contains the selected trigger (internal trigger input, filtered - * timer input or external trigger input) and the ) and the Slave - * mode (Disable, Reset, Gated, Trigger, External clock mode 1). + * timer input or external trigger input) and the Slave mode + * (Disable, Reset, Gated, Trigger, External clock mode 1). * @retval HAL status */ -HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchronization_IT(TIM_HandleTypeDef* htim, +HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchro_IT(TIM_HandleTypeDef* htim, TIM_SlaveConfigTypeDef* sSlaveConfig) { /* Check the parameters */ assert_param(IS_TIM_SLAVE_INSTANCE(htim->Instance)); assert_param(IS_TIM_SLAVE_MODE(sSlaveConfig->SlaveMode)); assert_param(IS_TIM_TRIGGER_SELECTION(sSlaveConfig->InputTrigger)); + __HAL_LOCK(htim); + htim->State = HAL_TIM_STATE_BUSY; - TIM_SlaveTimer_SetConfig(htim, sSlaveConfig); + + if (TIM_SlaveTimer_SetConfig(htim, sSlaveConfig) != HAL_OK) + { + htim->State = HAL_TIM_STATE_READY; + __HAL_UNLOCK(htim); + return HAL_ERROR; + } + /* Enable Trigger Interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_TRIGGER); + /* Disable Trigger DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_TRIGGER); + htim->State = HAL_TIM_STATE_READY; + __HAL_UNLOCK(htim); + return HAL_OK; } /** * @brief Read the captured value from Capture Compare unit - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channels to be enabled. + * @param htim TIM handle. + * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -3955,7 +4864,6 @@ HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchronization_IT(TIM_HandleTypeDef* htim, uint32_t HAL_TIM_ReadCapturedValue(TIM_HandleTypeDef* htim, uint32_t Channel) { uint32_t tmpreg = 0U; - __HAL_LOCK(htim); switch (Channel) { @@ -3963,8 +4871,10 @@ uint32_t HAL_TIM_ReadCapturedValue(TIM_HandleTypeDef* htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); + /* Return the capture 1 value */ - tmpreg = htim->Instance->CCR1; + tmpreg = htim->Instance->CCR1; + break; } @@ -3972,8 +4882,10 @@ uint32_t HAL_TIM_ReadCapturedValue(TIM_HandleTypeDef* htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); + /* Return the capture 2 value */ - tmpreg = htim->Instance->CCR2; + tmpreg = htim->Instance->CCR2; + break; } @@ -3981,8 +4893,10 @@ uint32_t HAL_TIM_ReadCapturedValue(TIM_HandleTypeDef* htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC3_INSTANCE(htim->Instance)); + /* Return the capture 3 value */ - tmpreg = htim->Instance->CCR3; + tmpreg = htim->Instance->CCR3; + break; } @@ -3990,8 +4904,10 @@ uint32_t HAL_TIM_ReadCapturedValue(TIM_HandleTypeDef* htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); + /* Return the capture 4 value */ - tmpreg = htim->Instance->CCR4; + tmpreg = htim->Instance->CCR4; + break; } @@ -3999,371 +4915,784 @@ uint32_t HAL_TIM_ReadCapturedValue(TIM_HandleTypeDef* htim, uint32_t Channel) break; } - __HAL_UNLOCK(htim); return tmpreg; } + /** * @} */ /** @defgroup TIM_Exported_Functions_Group9 TIM Callbacks functions - * @brief TIM Callbacks functions - * + * @brief TIM Callbacks functions + * @verbatim ============================================================================== ##### TIM Callbacks functions ##### ============================================================================== [..] This section provides TIM callback functions: - (+) Timer Period elapsed callback - (+) Timer Output Compare callback - (+) Timer Input capture callback - (+) Timer Trigger callback - (+) Timer Error callback + (+) TIM Period elapsed callback + (+) TIM Output Compare callback + (+) TIM Input capture callback + (+) TIM Trigger callback + (+) TIM Error callback @endverbatim * @{ */ /** - * @brief Period elapsed callback in non blocking mode - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @brief Period elapsed callback in non-blocking mode + * @param htim TIM handle * @retval None */ __weak void HAL_TIM_PeriodElapsedCallback(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, - the __HAL_TIM_PeriodElapsedCallback could be implemented in the user file + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_TIM_PeriodElapsedCallback could be implemented in the user file */ } /** - * @brief Output Compare callback in non blocking mode - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @brief Period elapsed half complete callback in non-blocking mode + * @param htim TIM handle * @retval None */ -__weak void HAL_TIM_OC_DelayElapsedCallback(TIM_HandleTypeDef* htim) +__weak void HAL_TIM_PeriodElapsedHalfCpltCallback(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, - the __HAL_TIM_OC_DelayElapsedCallback could be implemented in the user file + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_TIM_PeriodElapsedHalfCpltCallback could be implemented in the user file */ } /** - * @brief Input Capture callback in non blocking mode - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @brief Output Compare callback in non-blocking mode + * @param htim TIM OC handle * @retval None */ -__weak void HAL_TIM_IC_CaptureCallback(TIM_HandleTypeDef* htim) +__weak void HAL_TIM_OC_DelayElapsedCallback(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, - the __HAL_TIM_IC_CaptureCallback could be implemented in the user file + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_TIM_OC_DelayElapsedCallback could be implemented in the user file */ } /** - * @brief PWM Pulse finished callback in non blocking mode - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @brief Input Capture callback in non-blocking mode + * @param htim TIM IC handle * @retval None */ -__weak void HAL_TIM_PWM_PulseFinishedCallback(TIM_HandleTypeDef* htim) +__weak void HAL_TIM_IC_CaptureCallback(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, - the __HAL_TIM_PWM_PulseFinishedCallback could be implemented in the user file + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_TIM_IC_CaptureCallback could be implemented in the user file */ } /** - * @brief Hall Trigger detection callback in non blocking mode - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @brief Input Capture half complete callback in non-blocking mode + * @param htim TIM IC handle * @retval None */ -__weak void HAL_TIM_TriggerCallback(TIM_HandleTypeDef* htim) +__weak void HAL_TIM_IC_CaptureHalfCpltCallback(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, - the HAL_TIM_TriggerCallback could be implemented in the user file + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_TIM_IC_CaptureHalfCpltCallback could be implemented in the user file */ } /** - * @brief Timer error callback in non blocking mode - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @brief PWM Pulse finished callback in non-blocking mode + * @param htim TIM handle * @retval None */ -__weak void HAL_TIM_ErrorCallback(TIM_HandleTypeDef* htim) +__weak void HAL_TIM_PWM_PulseFinishedCallback(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, - the HAL_TIM_ErrorCallback could be implemented in the user file + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_TIM_PWM_PulseFinishedCallback could be implemented in the user file */ } -/** - * @} - */ - -/** @defgroup TIM_Exported_Functions_Group10 Peripheral State functions - * @brief Peripheral State functions - * -@verbatim - ============================================================================== - ##### Peripheral State functions ##### - ============================================================================== - [..] - This subsection permits to get in run-time the status of the peripheral - and the data flow. - -@endverbatim - * @{ - */ /** - * @brief Return the TIM Base state - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @retval HAL state + * @brief PWM Pulse finished half complete callback in non-blocking mode + * @param htim TIM handle + * @retval None */ -HAL_TIM_StateTypeDef HAL_TIM_Base_GetState(TIM_HandleTypeDef* htim) +__weak void HAL_TIM_PWM_PulseFinishedHalfCpltCallback(TIM_HandleTypeDef* htim) { - return htim->State; -} + /* Prevent unused argument(s) compilation warning */ + UNUSED(htim); -/** - * @brief Return the TIM OC state - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @retval HAL state - */ -HAL_TIM_StateTypeDef HAL_TIM_OC_GetState(TIM_HandleTypeDef* htim) -{ - return htim->State; + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_TIM_PWM_PulseFinishedHalfCpltCallback could be implemented in the user file + */ } /** - * @brief Return the TIM PWM state - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @retval HAL state + * @brief Hall Trigger detection callback in non-blocking mode + * @param htim TIM handle + * @retval None */ -HAL_TIM_StateTypeDef HAL_TIM_PWM_GetState(TIM_HandleTypeDef* htim) +__weak void HAL_TIM_TriggerCallback(TIM_HandleTypeDef* htim) { - return htim->State; -} + /* Prevent unused argument(s) compilation warning */ + UNUSED(htim); -/** - * @brief Return the TIM Input Capture state - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @retval HAL state - */ -HAL_TIM_StateTypeDef HAL_TIM_IC_GetState(TIM_HandleTypeDef* htim) -{ - return htim->State; + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_TIM_TriggerCallback could be implemented in the user file + */ } /** - * @brief Return the TIM One Pulse Mode state - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @retval HAL state + * @brief Hall Trigger detection half complete callback in non-blocking mode + * @param htim TIM handle + * @retval None */ -HAL_TIM_StateTypeDef HAL_TIM_OnePulse_GetState(TIM_HandleTypeDef* htim) +__weak void HAL_TIM_TriggerHalfCpltCallback(TIM_HandleTypeDef* htim) { - return htim->State; + /* Prevent unused argument(s) compilation warning */ + UNUSED(htim); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_TIM_TriggerHalfCpltCallback could be implemented in the user file + */ } /** - * @brief Return the TIM Encoder Mode state - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @retval HAL state + * @brief Timer error callback in non-blocking mode + * @param htim TIM handle + * @retval None */ -HAL_TIM_StateTypeDef HAL_TIM_Encoder_GetState(TIM_HandleTypeDef* htim) +__weak void HAL_TIM_ErrorCallback(TIM_HandleTypeDef* htim) { - return htim->State; + /* Prevent unused argument(s) compilation warning */ + UNUSED(htim); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_TIM_ErrorCallback could be implemented in the user file + */ } -/** - * @} - */ +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) /** - * @brief Time Base configuration - * @param TIMx: TIM peripheral - * @param Structure: pointer on TIM Time Base required parameters - * @retval None - */ -void TIM_Base_SetConfig(TIM_TypeDef* TIMx, TIM_Base_InitTypeDef* Structure) + * @brief Register a User TIM callback to be used instead of the weak predefined callback + * @param htim tim handle + * @param CallbackID ID of the callback to be registered + * This parameter can be one of the following values: + * @arg @ref HAL_TIM_BASE_MSPINIT_CB_ID Base MspInit Callback ID + * @arg @ref HAL_TIM_BASE_MSPDEINIT_CB_ID Base MspDeInit Callback ID + * @arg @ref HAL_TIM_IC_MSPINIT_CB_ID IC MspInit Callback ID + * @arg @ref HAL_TIM_IC_MSPDEINIT_CB_ID IC MspDeInit Callback ID + * @arg @ref HAL_TIM_OC_MSPINIT_CB_ID OC MspInit Callback ID + * @arg @ref HAL_TIM_OC_MSPDEINIT_CB_ID OC MspDeInit Callback ID + * @arg @ref HAL_TIM_PWM_MSPINIT_CB_ID PWM MspInit Callback ID + * @arg @ref HAL_TIM_PWM_MSPDEINIT_CB_ID PWM MspDeInit Callback ID + * @arg @ref HAL_TIM_ONE_PULSE_MSPINIT_CB_ID One Pulse MspInit Callback ID + * @arg @ref HAL_TIM_ONE_PULSE_MSPDEINIT_CB_ID One Pulse MspDeInit Callback ID + * @arg @ref HAL_TIM_ENCODER_MSPINIT_CB_ID Encoder MspInit Callback ID + * @arg @ref HAL_TIM_ENCODER_MSPDEINIT_CB_ID Encoder MspDeInit Callback ID + * @arg @ref HAL_TIM_HALL_SENSOR_MSPINIT_CB_ID Hall Sensor MspInit Callback ID + * @arg @ref HAL_TIM_HALL_SENSOR_MSPDEINIT_CB_ID Hall Sensor MspDeInit Callback ID + * @arg @ref HAL_TIM_PERIOD_ELAPSED_CB_ID Period Elapsed Callback ID + * @arg @ref HAL_TIM_PERIOD_ELAPSED_HALF_CB_ID Period Elapsed half complete Callback ID + * @arg @ref HAL_TIM_TRIGGER_CB_ID Trigger Callback ID + * @arg @ref HAL_TIM_TRIGGER_HALF_CB_ID Trigger half complete Callback ID + * @arg @ref HAL_TIM_IC_CAPTURE_CB_ID Input Capture Callback ID + * @arg @ref HAL_TIM_IC_CAPTURE_HALF_CB_ID Input Capture half complete Callback ID + * @arg @ref HAL_TIM_OC_DELAY_ELAPSED_CB_ID Output Compare Delay Elapsed Callback ID + * @arg @ref HAL_TIM_PWM_PULSE_FINISHED_CB_ID PWM Pulse Finished Callback ID + * @arg @ref HAL_TIM_PWM_PULSE_FINISHED_HALF_CB_ID PWM Pulse Finished half complete Callback ID + * @arg @ref HAL_TIM_ERROR_CB_ID Error Callback ID + * @arg @ref HAL_TIM_COMMUTATION_CB_ID Commutation Callback ID + * @arg @ref HAL_TIM_COMMUTATION_HALF_CB_ID Commutation half complete Callback ID + * @arg @ref HAL_TIM_BREAK_CB_ID Break Callback ID + * @param pCallback pointer to the callback function + * @retval status + */ +HAL_StatusTypeDef HAL_TIM_RegisterCallback(TIM_HandleTypeDef* htim, HAL_TIM_CallbackIDTypeDef CallbackID, + pTIM_CallbackTypeDef pCallback) { - uint32_t tmpcr1 = 0U; - tmpcr1 = TIMx->CR1; + HAL_StatusTypeDef status = HAL_OK; - /* Set TIM Time Base Unit parameters ---------------------------------------*/ - if (IS_TIM_CC3_INSTANCE(TIMx) != RESET) + if (pCallback == NULL) { - /* Select the Counter Mode */ - tmpcr1 &= ~(TIM_CR1_DIR | TIM_CR1_CMS); - tmpcr1 |= Structure->CounterMode; + return HAL_ERROR; } - if (IS_TIM_CC1_INSTANCE(TIMx) != RESET) - { - /* Set the clock division */ - tmpcr1 &= ~TIM_CR1_CKD; - tmpcr1 |= (uint32_t)Structure->ClockDivision; + /* Process locked */ + __HAL_LOCK(htim); + + if (htim->State == HAL_TIM_STATE_READY) + { + switch (CallbackID) + { + case HAL_TIM_BASE_MSPINIT_CB_ID : + htim->Base_MspInitCallback = pCallback; + break; + + case HAL_TIM_BASE_MSPDEINIT_CB_ID : + htim->Base_MspDeInitCallback = pCallback; + break; + + case HAL_TIM_IC_MSPINIT_CB_ID : + htim->IC_MspInitCallback = pCallback; + break; + + case HAL_TIM_IC_MSPDEINIT_CB_ID : + htim->IC_MspDeInitCallback = pCallback; + break; + + case HAL_TIM_OC_MSPINIT_CB_ID : + htim->OC_MspInitCallback = pCallback; + break; + + case HAL_TIM_OC_MSPDEINIT_CB_ID : + htim->OC_MspDeInitCallback = pCallback; + break; + + case HAL_TIM_PWM_MSPINIT_CB_ID : + htim->PWM_MspInitCallback = pCallback; + break; + + case HAL_TIM_PWM_MSPDEINIT_CB_ID : + htim->PWM_MspDeInitCallback = pCallback; + break; + + case HAL_TIM_ONE_PULSE_MSPINIT_CB_ID : + htim->OnePulse_MspInitCallback = pCallback; + break; + + case HAL_TIM_ONE_PULSE_MSPDEINIT_CB_ID : + htim->OnePulse_MspDeInitCallback = pCallback; + break; + + case HAL_TIM_ENCODER_MSPINIT_CB_ID : + htim->Encoder_MspInitCallback = pCallback; + break; + + case HAL_TIM_ENCODER_MSPDEINIT_CB_ID : + htim->Encoder_MspDeInitCallback = pCallback; + break; + + case HAL_TIM_HALL_SENSOR_MSPINIT_CB_ID : + htim->HallSensor_MspInitCallback = pCallback; + break; + + case HAL_TIM_HALL_SENSOR_MSPDEINIT_CB_ID : + htim->HallSensor_MspDeInitCallback = pCallback; + break; + + case HAL_TIM_PERIOD_ELAPSED_CB_ID : + htim->PeriodElapsedCallback = pCallback; + break; + + case HAL_TIM_PERIOD_ELAPSED_HALF_CB_ID : + htim->PeriodElapsedHalfCpltCallback = pCallback; + break; + + case HAL_TIM_TRIGGER_CB_ID : + htim->TriggerCallback = pCallback; + break; + + case HAL_TIM_TRIGGER_HALF_CB_ID : + htim->TriggerHalfCpltCallback = pCallback; + break; + + case HAL_TIM_IC_CAPTURE_CB_ID : + htim->IC_CaptureCallback = pCallback; + break; + + case HAL_TIM_IC_CAPTURE_HALF_CB_ID : + htim->IC_CaptureHalfCpltCallback = pCallback; + break; + + case HAL_TIM_OC_DELAY_ELAPSED_CB_ID : + htim->OC_DelayElapsedCallback = pCallback; + break; + + case HAL_TIM_PWM_PULSE_FINISHED_CB_ID : + htim->PWM_PulseFinishedCallback = pCallback; + break; + + case HAL_TIM_PWM_PULSE_FINISHED_HALF_CB_ID : + htim->PWM_PulseFinishedHalfCpltCallback = pCallback; + break; + + case HAL_TIM_ERROR_CB_ID : + htim->ErrorCallback = pCallback; + break; + + case HAL_TIM_COMMUTATION_CB_ID : + htim->CommutationCallback = pCallback; + break; + + case HAL_TIM_COMMUTATION_HALF_CB_ID : + htim->CommutationHalfCpltCallback = pCallback; + break; + + case HAL_TIM_BREAK_CB_ID : + htim->BreakCallback = pCallback; + break; + + default : + /* Return error status */ + status = HAL_ERROR; + break; + } } + else if (htim->State == HAL_TIM_STATE_RESET) + { + switch (CallbackID) + { + case HAL_TIM_BASE_MSPINIT_CB_ID : + htim->Base_MspInitCallback = pCallback; + break; - TIMx->CR1 = tmpcr1; - /* Set the Auto-reload value */ - TIMx->ARR = (uint32_t)Structure->Period ; - /* Set the Prescaler value */ - TIMx->PSC = (uint32_t)Structure->Prescaler; + case HAL_TIM_BASE_MSPDEINIT_CB_ID : + htim->Base_MspDeInitCallback = pCallback; + break; + + case HAL_TIM_IC_MSPINIT_CB_ID : + htim->IC_MspInitCallback = pCallback; + break; + + case HAL_TIM_IC_MSPDEINIT_CB_ID : + htim->IC_MspDeInitCallback = pCallback; + break; + + case HAL_TIM_OC_MSPINIT_CB_ID : + htim->OC_MspInitCallback = pCallback; + break; + + case HAL_TIM_OC_MSPDEINIT_CB_ID : + htim->OC_MspDeInitCallback = pCallback; + break; + + case HAL_TIM_PWM_MSPINIT_CB_ID : + htim->PWM_MspInitCallback = pCallback; + break; + + case HAL_TIM_PWM_MSPDEINIT_CB_ID : + htim->PWM_MspDeInitCallback = pCallback; + break; + + case HAL_TIM_ONE_PULSE_MSPINIT_CB_ID : + htim->OnePulse_MspInitCallback = pCallback; + break; + + case HAL_TIM_ONE_PULSE_MSPDEINIT_CB_ID : + htim->OnePulse_MspDeInitCallback = pCallback; + break; + + case HAL_TIM_ENCODER_MSPINIT_CB_ID : + htim->Encoder_MspInitCallback = pCallback; + break; + + case HAL_TIM_ENCODER_MSPDEINIT_CB_ID : + htim->Encoder_MspDeInitCallback = pCallback; + break; + + case HAL_TIM_HALL_SENSOR_MSPINIT_CB_ID : + htim->HallSensor_MspInitCallback = pCallback; + break; + + case HAL_TIM_HALL_SENSOR_MSPDEINIT_CB_ID : + htim->HallSensor_MspDeInitCallback = pCallback; + break; - if (IS_TIM_ADVANCED_INSTANCE(TIMx) != RESET) + default : + /* Return error status */ + status = HAL_ERROR; + break; + } + } + else { - /* Set the Repetition Counter value */ - TIMx->RCR = Structure->RepetitionCounter; + /* Return error status */ + status = HAL_ERROR; } - /* Generate an update event to reload the Prescaler - and the repetition counter(only for TIM1 and TIM8) value immediately */ - TIMx->EGR = TIM_EGR_UG; + /* Release Lock */ + __HAL_UNLOCK(htim); + + return status; } /** - * @brief Configure the TI1 as Input. - * @param TIMx to select the TIM peripheral. - * @param TIM_ICPolarity : The Input Polarity. - * This parameter can be one of the following values: - * @arg TIM_ICPolarity_Rising - * @arg TIM_ICPolarity_Falling - * @arg TIM_ICPolarity_BothEdge - * @param TIM_ICSelection: specifies the input to be used. - * This parameter can be one of the following values: - * @arg TIM_ICSelection_DirectTI: TIM Input 1 is selected to be connected to IC1. - * @arg TIM_ICSelection_IndirectTI: TIM Input 1 is selected to be connected to IC2. - * @arg TIM_ICSelection_TRC: TIM Input 1 is selected to be connected to TRC. - * @param TIM_ICFilter: Specifies the Input Capture Filter. - * This parameter must be a value between 0x00 and 0x0F. - * @note TIM_ICFilter and TIM_ICPolarity are not used in INDIRECT mode as TI2FP1 - * (on channel2 path) is used as the input signal. Therefore CCMR1 must be - * protected against un-initialized filter and polarity values. - * @retval None - */ -void TIM_TI1_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, - uint32_t TIM_ICFilter) + * @brief Unregister a TIM callback + * TIM callback is redirected to the weak predefined callback + * @param htim tim handle + * @param CallbackID ID of the callback to be unregistered + * This parameter can be one of the following values: + * @arg @ref HAL_TIM_BASE_MSPINIT_CB_ID Base MspInit Callback ID + * @arg @ref HAL_TIM_BASE_MSPDEINIT_CB_ID Base MspDeInit Callback ID + * @arg @ref HAL_TIM_IC_MSPINIT_CB_ID IC MspInit Callback ID + * @arg @ref HAL_TIM_IC_MSPDEINIT_CB_ID IC MspDeInit Callback ID + * @arg @ref HAL_TIM_OC_MSPINIT_CB_ID OC MspInit Callback ID + * @arg @ref HAL_TIM_OC_MSPDEINIT_CB_ID OC MspDeInit Callback ID + * @arg @ref HAL_TIM_PWM_MSPINIT_CB_ID PWM MspInit Callback ID + * @arg @ref HAL_TIM_PWM_MSPDEINIT_CB_ID PWM MspDeInit Callback ID + * @arg @ref HAL_TIM_ONE_PULSE_MSPINIT_CB_ID One Pulse MspInit Callback ID + * @arg @ref HAL_TIM_ONE_PULSE_MSPDEINIT_CB_ID One Pulse MspDeInit Callback ID + * @arg @ref HAL_TIM_ENCODER_MSPINIT_CB_ID Encoder MspInit Callback ID + * @arg @ref HAL_TIM_ENCODER_MSPDEINIT_CB_ID Encoder MspDeInit Callback ID + * @arg @ref HAL_TIM_HALL_SENSOR_MSPINIT_CB_ID Hall Sensor MspInit Callback ID + * @arg @ref HAL_TIM_HALL_SENSOR_MSPDEINIT_CB_ID Hall Sensor MspDeInit Callback ID + * @arg @ref HAL_TIM_PERIOD_ELAPSED_CB_ID Period Elapsed Callback ID + * @arg @ref HAL_TIM_PERIOD_ELAPSED_HALF_CB_ID Period Elapsed half complete Callback ID + * @arg @ref HAL_TIM_TRIGGER_CB_ID Trigger Callback ID + * @arg @ref HAL_TIM_TRIGGER_HALF_CB_ID Trigger half complete Callback ID + * @arg @ref HAL_TIM_IC_CAPTURE_CB_ID Input Capture Callback ID + * @arg @ref HAL_TIM_IC_CAPTURE_HALF_CB_ID Input Capture half complete Callback ID + * @arg @ref HAL_TIM_OC_DELAY_ELAPSED_CB_ID Output Compare Delay Elapsed Callback ID + * @arg @ref HAL_TIM_PWM_PULSE_FINISHED_CB_ID PWM Pulse Finished Callback ID + * @arg @ref HAL_TIM_PWM_PULSE_FINISHED_HALF_CB_ID PWM Pulse Finished half complete Callback ID + * @arg @ref HAL_TIM_ERROR_CB_ID Error Callback ID + * @arg @ref HAL_TIM_COMMUTATION_CB_ID Commutation Callback ID + * @arg @ref HAL_TIM_COMMUTATION_HALF_CB_ID Commutation half complete Callback ID + * @arg @ref HAL_TIM_BREAK_CB_ID Break Callback ID + * @retval status + */ +HAL_StatusTypeDef HAL_TIM_UnRegisterCallback(TIM_HandleTypeDef* htim, HAL_TIM_CallbackIDTypeDef CallbackID) { - uint32_t tmpccmr1 = 0U; - uint32_t tmpccer = 0U; - /* Disable the Channel 1: Reset the CC1E Bit */ - TIMx->CCER &= ~TIM_CCER_CC1E; - tmpccmr1 = TIMx->CCMR1; - tmpccer = TIMx->CCER; + HAL_StatusTypeDef status = HAL_OK; - /* Select the Input */ - if (IS_TIM_CC2_INSTANCE(TIMx) != RESET) + /* Process locked */ + __HAL_LOCK(htim); + + if (htim->State == HAL_TIM_STATE_READY) { - tmpccmr1 &= ~TIM_CCMR1_CC1S; - tmpccmr1 |= TIM_ICSelection; + switch (CallbackID) + { + case HAL_TIM_BASE_MSPINIT_CB_ID : + htim->Base_MspInitCallback = HAL_TIM_Base_MspInit; /* Legacy weak Base MspInit Callback */ + break; + + case HAL_TIM_BASE_MSPDEINIT_CB_ID : + htim->Base_MspDeInitCallback = HAL_TIM_Base_MspDeInit; /* Legacy weak Base Msp DeInit Callback */ + break; + + case HAL_TIM_IC_MSPINIT_CB_ID : + htim->IC_MspInitCallback = HAL_TIM_IC_MspInit; /* Legacy weak IC Msp Init Callback */ + break; + + case HAL_TIM_IC_MSPDEINIT_CB_ID : + htim->IC_MspDeInitCallback = HAL_TIM_IC_MspDeInit; /* Legacy weak IC Msp DeInit Callback */ + break; + + case HAL_TIM_OC_MSPINIT_CB_ID : + htim->OC_MspInitCallback = HAL_TIM_OC_MspInit; /* Legacy weak OC Msp Init Callback */ + break; + + case HAL_TIM_OC_MSPDEINIT_CB_ID : + htim->OC_MspDeInitCallback = HAL_TIM_OC_MspDeInit; /* Legacy weak OC Msp DeInit Callback */ + break; + + case HAL_TIM_PWM_MSPINIT_CB_ID : + htim->PWM_MspInitCallback = HAL_TIM_PWM_MspInit; /* Legacy weak PWM Msp Init Callback */ + break; + + case HAL_TIM_PWM_MSPDEINIT_CB_ID : + htim->PWM_MspDeInitCallback = HAL_TIM_PWM_MspDeInit; /* Legacy weak PWM Msp DeInit Callback */ + break; + + case HAL_TIM_ONE_PULSE_MSPINIT_CB_ID : + htim->OnePulse_MspInitCallback = HAL_TIM_OnePulse_MspInit; /* Legacy weak One Pulse Msp Init Callback */ + break; + + case HAL_TIM_ONE_PULSE_MSPDEINIT_CB_ID : + htim->OnePulse_MspDeInitCallback = HAL_TIM_OnePulse_MspDeInit; /* Legacy weak One Pulse Msp DeInit Callback */ + break; + + case HAL_TIM_ENCODER_MSPINIT_CB_ID : + htim->Encoder_MspInitCallback = HAL_TIM_Encoder_MspInit; /* Legacy weak Encoder Msp Init Callback */ + break; + + case HAL_TIM_ENCODER_MSPDEINIT_CB_ID : + htim->Encoder_MspDeInitCallback = HAL_TIM_Encoder_MspDeInit; /* Legacy weak Encoder Msp DeInit Callback */ + break; + + case HAL_TIM_HALL_SENSOR_MSPINIT_CB_ID : + htim->HallSensor_MspInitCallback = HAL_TIMEx_HallSensor_MspInit; /* Legacy weak Hall Sensor Msp Init Callback */ + break; + + case HAL_TIM_HALL_SENSOR_MSPDEINIT_CB_ID : + htim->HallSensor_MspDeInitCallback = HAL_TIMEx_HallSensor_MspDeInit; /* Legacy weak Hall Sensor Msp DeInit Callback */ + break; + + case HAL_TIM_PERIOD_ELAPSED_CB_ID : + htim->PeriodElapsedCallback = HAL_TIM_PeriodElapsedCallback; /* Legacy weak Period Elapsed Callback */ + break; + + case HAL_TIM_PERIOD_ELAPSED_HALF_CB_ID : + htim->PeriodElapsedHalfCpltCallback = HAL_TIM_PeriodElapsedHalfCpltCallback; /* Legacy weak Period Elapsed half complete Callback */ + break; + + case HAL_TIM_TRIGGER_CB_ID : + htim->TriggerCallback = HAL_TIM_TriggerCallback; /* Legacy weak Trigger Callback */ + break; + + case HAL_TIM_TRIGGER_HALF_CB_ID : + htim->TriggerHalfCpltCallback = HAL_TIM_TriggerHalfCpltCallback; /* Legacy weak Trigger half complete Callback */ + break; + + case HAL_TIM_IC_CAPTURE_CB_ID : + htim->IC_CaptureCallback = HAL_TIM_IC_CaptureCallback; /* Legacy weak IC Capture Callback */ + break; + + case HAL_TIM_IC_CAPTURE_HALF_CB_ID : + htim->IC_CaptureHalfCpltCallback = HAL_TIM_IC_CaptureHalfCpltCallback; /* Legacy weak IC Capture half complete Callback */ + break; + + case HAL_TIM_OC_DELAY_ELAPSED_CB_ID : + htim->OC_DelayElapsedCallback = HAL_TIM_OC_DelayElapsedCallback; /* Legacy weak OC Delay Elapsed Callback */ + break; + + case HAL_TIM_PWM_PULSE_FINISHED_CB_ID : + htim->PWM_PulseFinishedCallback = HAL_TIM_PWM_PulseFinishedCallback; /* Legacy weak PWM Pulse Finished Callback */ + break; + + case HAL_TIM_PWM_PULSE_FINISHED_HALF_CB_ID : + htim->PWM_PulseFinishedHalfCpltCallback = HAL_TIM_PWM_PulseFinishedHalfCpltCallback; /* Legacy weak PWM Pulse Finished half complete Callback */ + break; + + case HAL_TIM_ERROR_CB_ID : + htim->ErrorCallback = HAL_TIM_ErrorCallback; /* Legacy weak Error Callback */ + break; + + case HAL_TIM_COMMUTATION_CB_ID : + htim->CommutationCallback = HAL_TIMEx_CommutCallback; /* Legacy weak Commutation Callback */ + break; + + case HAL_TIM_COMMUTATION_HALF_CB_ID : + htim->CommutationHalfCpltCallback = HAL_TIMEx_CommutHalfCpltCallback; /* Legacy weak Commutation half complete Callback */ + break; + + case HAL_TIM_BREAK_CB_ID : + htim->BreakCallback = HAL_TIMEx_BreakCallback; /* Legacy weak Break Callback */ + break; + + default : + /* Return error status */ + status = HAL_ERROR; + break; + } + } + else if (htim->State == HAL_TIM_STATE_RESET) + { + switch (CallbackID) + { + case HAL_TIM_BASE_MSPINIT_CB_ID : + htim->Base_MspInitCallback = HAL_TIM_Base_MspInit; /* Legacy weak Base MspInit Callback */ + break; + + case HAL_TIM_BASE_MSPDEINIT_CB_ID : + htim->Base_MspDeInitCallback = HAL_TIM_Base_MspDeInit; /* Legacy weak Base Msp DeInit Callback */ + break; + + case HAL_TIM_IC_MSPINIT_CB_ID : + htim->IC_MspInitCallback = HAL_TIM_IC_MspInit; /* Legacy weak IC Msp Init Callback */ + break; + + case HAL_TIM_IC_MSPDEINIT_CB_ID : + htim->IC_MspDeInitCallback = HAL_TIM_IC_MspDeInit; /* Legacy weak IC Msp DeInit Callback */ + break; + + case HAL_TIM_OC_MSPINIT_CB_ID : + htim->OC_MspInitCallback = HAL_TIM_OC_MspInit; /* Legacy weak OC Msp Init Callback */ + break; + + case HAL_TIM_OC_MSPDEINIT_CB_ID : + htim->OC_MspDeInitCallback = HAL_TIM_OC_MspDeInit; /* Legacy weak OC Msp DeInit Callback */ + break; + + case HAL_TIM_PWM_MSPINIT_CB_ID : + htim->PWM_MspInitCallback = HAL_TIM_PWM_MspInit; /* Legacy weak PWM Msp Init Callback */ + break; + + case HAL_TIM_PWM_MSPDEINIT_CB_ID : + htim->PWM_MspDeInitCallback = HAL_TIM_PWM_MspDeInit; /* Legacy weak PWM Msp DeInit Callback */ + break; + + case HAL_TIM_ONE_PULSE_MSPINIT_CB_ID : + htim->OnePulse_MspInitCallback = HAL_TIM_OnePulse_MspInit; /* Legacy weak One Pulse Msp Init Callback */ + break; + + case HAL_TIM_ONE_PULSE_MSPDEINIT_CB_ID : + htim->OnePulse_MspDeInitCallback = HAL_TIM_OnePulse_MspDeInit; /* Legacy weak One Pulse Msp DeInit Callback */ + break; + + case HAL_TIM_ENCODER_MSPINIT_CB_ID : + htim->Encoder_MspInitCallback = HAL_TIM_Encoder_MspInit; /* Legacy weak Encoder Msp Init Callback */ + break; + + case HAL_TIM_ENCODER_MSPDEINIT_CB_ID : + htim->Encoder_MspDeInitCallback = HAL_TIM_Encoder_MspDeInit; /* Legacy weak Encoder Msp DeInit Callback */ + break; + + case HAL_TIM_HALL_SENSOR_MSPINIT_CB_ID : + htim->HallSensor_MspInitCallback = HAL_TIMEx_HallSensor_MspInit; /* Legacy weak Hall Sensor Msp Init Callback */ + break; + + case HAL_TIM_HALL_SENSOR_MSPDEINIT_CB_ID : + htim->HallSensor_MspDeInitCallback = HAL_TIMEx_HallSensor_MspDeInit; /* Legacy weak Hall Sensor Msp DeInit Callback */ + break; + + default : + /* Return error status */ + status = HAL_ERROR; + break; + } } else { - tmpccmr1 &= ~TIM_CCMR1_CC1S; - tmpccmr1 |= TIM_CCMR1_CC1S_0; + /* Return error status */ + status = HAL_ERROR; } - /* Set the filter */ - tmpccmr1 &= ~TIM_CCMR1_IC1F; - tmpccmr1 |= ((TIM_ICFilter << 4U) & TIM_CCMR1_IC1F); - /* Select the Polarity and set the CC1E Bit */ - tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC1NP); - tmpccer |= (TIM_ICPolarity & (TIM_CCER_CC1P | TIM_CCER_CC1NP)); - /* Write to TIMx CCMR1 and CCER registers */ - TIMx->CCMR1 = tmpccmr1; - TIMx->CCER = tmpccer; + /* Release Lock */ + __HAL_UNLOCK(htim); + + return status; } +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ /** - * @brief Time Output Compare 2 configuration - * @param TIMx to select the TIM peripheral - * @param OC_Config: The output configuration structure + * @} + */ + +/** @defgroup TIM_Exported_Functions_Group10 TIM Peripheral State functions + * @brief TIM Peripheral State functions + * +@verbatim + ============================================================================== + ##### Peripheral State functions ##### + ============================================================================== + [..] + This subsection permits to get in run-time the status of the peripheral + and the data flow. + +@endverbatim + * @{ + */ + +/** + * @brief Return the TIM Base handle state. + * @param htim TIM Base handle + * @retval HAL state + */ +HAL_TIM_StateTypeDef HAL_TIM_Base_GetState(TIM_HandleTypeDef* htim) +{ + return htim->State; +} + +/** + * @brief Return the TIM OC handle state. + * @param htim TIM Output Compare handle + * @retval HAL state + */ +HAL_TIM_StateTypeDef HAL_TIM_OC_GetState(TIM_HandleTypeDef* htim) +{ + return htim->State; +} + +/** + * @brief Return the TIM PWM handle state. + * @param htim TIM handle + * @retval HAL state + */ +HAL_TIM_StateTypeDef HAL_TIM_PWM_GetState(TIM_HandleTypeDef* htim) +{ + return htim->State; +} + +/** + * @brief Return the TIM Input Capture handle state. + * @param htim TIM IC handle + * @retval HAL state + */ +HAL_TIM_StateTypeDef HAL_TIM_IC_GetState(TIM_HandleTypeDef* htim) +{ + return htim->State; +} + +/** + * @brief Return the TIM One Pulse Mode handle state. + * @param htim TIM OPM handle + * @retval HAL state + */ +HAL_TIM_StateTypeDef HAL_TIM_OnePulse_GetState(TIM_HandleTypeDef* htim) +{ + return htim->State; +} + +/** + * @brief Return the TIM Encoder Mode handle state. + * @param htim TIM Encoder Interface handle + * @retval HAL state + */ +HAL_TIM_StateTypeDef HAL_TIM_Encoder_GetState(TIM_HandleTypeDef* htim) +{ + return htim->State; +} + +/** + * @} + */ + +/** + * @} + */ + +/** @defgroup TIM_Private_Functions TIM Private Functions + * @{ + */ + +/** + * @brief TIM DMA error callback + * @param hdma pointer to DMA handle. * @retval None */ -void TIM_OC2_SetConfig(TIM_TypeDef* TIMx, TIM_OC_InitTypeDef* OC_Config) +void TIM_DMAError(DMA_HandleTypeDef* hdma) { - uint32_t tmpccmrx = 0U; - uint32_t tmpccer = 0U; - uint32_t tmpcr2 = 0U; - /* Disable the Channel 2: Reset the CC2E Bit */ - TIMx->CCER &= ~TIM_CCER_CC2E; - /* Get the TIMx CCER register value */ - tmpccer = TIMx->CCER; - /* Get the TIMx CR2 register value */ - tmpcr2 = TIMx->CR2; - /* Get the TIMx CCMR1 register value */ - tmpccmrx = TIMx->CCMR1; - /* Reset the Output Compare mode and Capture/Compare selection Bits */ - tmpccmrx &= ~TIM_CCMR1_OC2M; - tmpccmrx &= ~TIM_CCMR1_CC2S; - /* Select the Output Compare Mode */ - tmpccmrx |= (OC_Config->OCMode << 8U); - /* Reset the Output Polarity level */ - tmpccer &= ~TIM_CCER_CC2P; - /* Set the Output Compare Polarity */ - tmpccer |= (OC_Config->OCPolarity << 4U); + TIM_HandleTypeDef* htim = (TIM_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; - if (IS_TIM_ADVANCED_INSTANCE(TIMx) != RESET) - { - assert_param(IS_TIM_OCN_POLARITY(OC_Config->OCNPolarity)); - /* Reset the Output N Polarity level */ - tmpccer &= ~TIM_CCER_CC2NP; - /* Set the Output N Polarity */ - tmpccer |= (OC_Config->OCNPolarity << 4U); - /* Reset the Output N State */ - tmpccer &= ~TIM_CCER_CC2NE; - /* Reset the Output Compare and Output Compare N IDLE State */ - tmpcr2 &= ~TIM_CR2_OIS2; - tmpcr2 &= ~TIM_CR2_OIS2N; - /* Set the Output Idle state */ - tmpcr2 |= (OC_Config->OCIdleState << 2U); - /* Set the Output N Idle state */ - tmpcr2 |= (OC_Config->OCNIdleState << 2U); - } + htim->State = HAL_TIM_STATE_READY; - /* Write to TIMx CR2 */ - TIMx->CR2 = tmpcr2; - /* Write to TIMx CCMR1 */ - TIMx->CCMR1 = tmpccmrx; - /* Set the Capture Compare Register value */ - TIMx->CCR2 = OC_Config->Pulse; - /* Write to TIMx CCER */ - TIMx->CCER = tmpccer; +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->ErrorCallback(htim); +#else + HAL_TIM_ErrorCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } /** * @brief TIM DMA Delay Pulse complete callback. - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA module. + * @param hdma pointer to DMA handle. * @retval None */ void TIM_DMADelayPulseCplt(DMA_HandleTypeDef* hdma) { - TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + TIM_HandleTypeDef* htim = (TIM_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + htim->State = HAL_TIM_STATE_READY; if (hdma == htim->hdma[TIM_DMA_ID_CC1]) @@ -4382,33 +5711,70 @@ void TIM_DMADelayPulseCplt(DMA_HandleTypeDef* hdma) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4; } + else + { + /* nothing to do */ + } +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->PWM_PulseFinishedCallback(htim); +#else HAL_TIM_PWM_PulseFinishedCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } /** - * @brief TIM DMA error callback - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA module. + * @brief TIM DMA Delay Pulse half complete callback. + * @param hdma pointer to DMA handle. * @retval None */ -void TIM_DMAError(DMA_HandleTypeDef* hdma) +void TIM_DMADelayPulseHalfCplt(DMA_HandleTypeDef* hdma) { - TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + TIM_HandleTypeDef* htim = (TIM_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + htim->State = HAL_TIM_STATE_READY; - HAL_TIM_ErrorCallback(htim); + + if (hdma == htim->hdma[TIM_DMA_ID_CC1]) + { + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1; + } + else if (hdma == htim->hdma[TIM_DMA_ID_CC2]) + { + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2; + } + else if (hdma == htim->hdma[TIM_DMA_ID_CC3]) + { + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3; + } + else if (hdma == htim->hdma[TIM_DMA_ID_CC4]) + { + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4; + } + else + { + /* nothing to do */ + } + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->PWM_PulseFinishedHalfCpltCallback(htim); +#else + HAL_TIM_PWM_PulseFinishedHalfCpltCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } /** * @brief TIM DMA Capture complete callback. - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA module. + * @param hdma pointer to DMA handle. * @retval None */ void TIM_DMACaptureCplt(DMA_HandleTypeDef* hdma) { - TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + TIM_HandleTypeDef* htim = (TIM_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + htim->State = HAL_TIM_STATE_READY; if (hdma == htim->hdma[TIM_DMA_ID_CC1]) @@ -4427,100 +5793,234 @@ void TIM_DMACaptureCplt(DMA_HandleTypeDef* hdma) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4; } + else + { + /* nothing to do */ + } +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->IC_CaptureCallback(htim); +#else HAL_TIM_IC_CaptureCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } /** - * @brief Enables or disables the TIM Capture Compare Channel x. - * @param TIMx to select the TIM peripheral - * @param Channel: specifies the TIM Channel - * This parameter can be one of the following values: - * @arg TIM_Channel_1: TIM Channel 1 - * @arg TIM_Channel_2: TIM Channel 2 - * @arg TIM_Channel_3: TIM Channel 3 - * @arg TIM_Channel_4: TIM Channel 4 - * @param ChannelState: specifies the TIM Channel CCxE bit new state. - * This parameter can be: TIM_CCx_ENABLE or TIM_CCx_Disable. + * @brief TIM DMA Capture half complete callback. + * @param hdma pointer to DMA handle. * @retval None */ -void TIM_CCxChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelState) +void TIM_DMACaptureHalfCplt(DMA_HandleTypeDef* hdma) { - uint32_t tmp = 0U; - /* Check the parameters */ - assert_param(IS_TIM_CC1_INSTANCE(TIMx)); - assert_param(IS_TIM_CHANNELS(Channel)); - tmp = TIM_CCER_CC1E << Channel; - /* Reset the CCxE Bit */ - TIMx->CCER &= ~tmp; - /* Set or reset the CCxE Bit */ - TIMx->CCER |= (uint32_t)(ChannelState << Channel); + TIM_HandleTypeDef* htim = (TIM_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + + htim->State = HAL_TIM_STATE_READY; + + if (hdma == htim->hdma[TIM_DMA_ID_CC1]) + { + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1; + } + else if (hdma == htim->hdma[TIM_DMA_ID_CC2]) + { + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2; + } + else if (hdma == htim->hdma[TIM_DMA_ID_CC3]) + { + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3; + } + else if (hdma == htim->hdma[TIM_DMA_ID_CC4]) + { + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4; + } + else + { + /* nothing to do */ + } + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->IC_CaptureHalfCpltCallback(htim); +#else + HAL_TIM_IC_CaptureHalfCpltCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } /** * @brief TIM DMA Period Elapse complete callback. - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA module. + * @param hdma pointer to DMA handle. * @retval None */ static void TIM_DMAPeriodElapsedCplt(DMA_HandleTypeDef* hdma) { - TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + TIM_HandleTypeDef* htim = (TIM_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + htim->State = HAL_TIM_STATE_READY; + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->PeriodElapsedCallback(htim); +#else HAL_TIM_PeriodElapsedCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ +} + +/** + * @brief TIM DMA Period Elapse half complete callback. + * @param hdma pointer to DMA handle. + * @retval None + */ +static void TIM_DMAPeriodElapsedHalfCplt(DMA_HandleTypeDef* hdma) +{ + TIM_HandleTypeDef* htim = (TIM_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + + htim->State = HAL_TIM_STATE_READY; + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->PeriodElapsedHalfCpltCallback(htim); +#else + HAL_TIM_PeriodElapsedHalfCpltCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } /** * @brief TIM DMA Trigger callback. - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA module. + * @param hdma pointer to DMA handle. * @retval None */ static void TIM_DMATriggerCplt(DMA_HandleTypeDef* hdma) { - TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + TIM_HandleTypeDef* htim = (TIM_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + htim->State = HAL_TIM_STATE_READY; + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->TriggerCallback(htim); +#else HAL_TIM_TriggerCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ +} + +/** + * @brief TIM DMA Trigger half complete callback. + * @param hdma pointer to DMA handle. + * @retval None + */ +static void TIM_DMATriggerHalfCplt(DMA_HandleTypeDef* hdma) +{ + TIM_HandleTypeDef* htim = (TIM_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + + htim->State = HAL_TIM_STATE_READY; + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->TriggerHalfCpltCallback(htim); +#else + HAL_TIM_TriggerHalfCpltCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ +} + +/** + * @brief Time Base configuration + * @param TIMx TIM peripheral + * @param Structure TIM Base configuration structure + * @retval None + */ +void TIM_Base_SetConfig(TIM_TypeDef* TIMx, TIM_Base_InitTypeDef* Structure) +{ + uint32_t tmpcr1; + tmpcr1 = TIMx->CR1; + + /* Set TIM Time Base Unit parameters ---------------------------------------*/ + if (IS_TIM_COUNTER_MODE_SELECT_INSTANCE(TIMx)) + { + /* Select the Counter Mode */ + tmpcr1 &= ~(TIM_CR1_DIR | TIM_CR1_CMS); + tmpcr1 |= Structure->CounterMode; + } + + if (IS_TIM_CLOCK_DIVISION_INSTANCE(TIMx)) + { + /* Set the clock division */ + tmpcr1 &= ~TIM_CR1_CKD; + tmpcr1 |= (uint32_t)Structure->ClockDivision; + } + + /* Set the auto-reload preload */ + MODIFY_REG(tmpcr1, TIM_CR1_ARPE, Structure->AutoReloadPreload); + + TIMx->CR1 = tmpcr1; + + /* Set the Autoreload value */ + TIMx->ARR = (uint32_t)Structure->Period ; + + /* Set the Prescaler value */ + TIMx->PSC = Structure->Prescaler; + + if (IS_TIM_REPETITION_COUNTER_INSTANCE(TIMx)) + { + /* Set the Repetition Counter value */ + TIMx->RCR = Structure->RepetitionCounter; + } + + /* Generate an update event to reload the Prescaler + and the repetition counter (only for advanced timer) value immediately */ + TIMx->EGR = TIM_EGR_UG; } /** - * @brief Time Output Compare 1 configuration + * @brief Timer Output Compare 1 configuration * @param TIMx to select the TIM peripheral - * @param OC_Config: The output configuration structure + * @param OC_Config The ouput configuration structure * @retval None */ static void TIM_OC1_SetConfig(TIM_TypeDef* TIMx, TIM_OC_InitTypeDef* OC_Config) { - uint32_t tmpccmrx = 0U; - uint32_t tmpccer = 0U; - uint32_t tmpcr2 = 0U; + uint32_t tmpccmrx; + uint32_t tmpccer; + uint32_t tmpcr2; + /* Disable the Channel 1: Reset the CC1E Bit */ TIMx->CCER &= ~TIM_CCER_CC1E; + /* Get the TIMx CCER register value */ tmpccer = TIMx->CCER; /* Get the TIMx CR2 register value */ - tmpcr2 = TIMx->CR2; + tmpcr2 = TIMx->CR2; + /* Get the TIMx CCMR1 register value */ tmpccmrx = TIMx->CCMR1; + /* Reset the Output Compare Mode Bits */ tmpccmrx &= ~TIM_CCMR1_OC1M; tmpccmrx &= ~TIM_CCMR1_CC1S; /* Select the Output Compare Mode */ tmpccmrx |= OC_Config->OCMode; + /* Reset the Output Polarity level */ tmpccer &= ~TIM_CCER_CC1P; /* Set the Output Compare Polarity */ tmpccer |= OC_Config->OCPolarity; - if (IS_TIM_ADVANCED_INSTANCE(TIMx) != RESET) + if (IS_TIM_CCXN_INSTANCE(TIMx, TIM_CHANNEL_1)) { + /* Check parameters */ + assert_param(IS_TIM_OCN_POLARITY(OC_Config->OCNPolarity)); + /* Reset the Output N Polarity level */ tmpccer &= ~TIM_CCER_CC1NP; /* Set the Output N Polarity */ tmpccer |= OC_Config->OCNPolarity; /* Reset the Output N State */ tmpccer &= ~TIM_CCER_CC1NE; + } + + if (IS_TIM_BREAK_INSTANCE(TIMx)) + { + /* Check parameters */ + assert_param(IS_TIM_OCNIDLE_STATE(OC_Config->OCNIdleState)); + assert_param(IS_TIM_OCIDLE_STATE(OC_Config->OCIdleState)); + /* Reset the Output Compare and Output Compare N IDLE State */ tmpcr2 &= ~TIM_CR2_OIS1; tmpcr2 &= ~TIM_CR2_OIS1N; @@ -4532,54 +6032,145 @@ static void TIM_OC1_SetConfig(TIM_TypeDef* TIMx, TIM_OC_InitTypeDef* OC_Config) /* Write to TIMx CR2 */ TIMx->CR2 = tmpcr2; + /* Write to TIMx CCMR1 */ TIMx->CCMR1 = tmpccmrx; + /* Set the Capture Compare Register value */ TIMx->CCR1 = OC_Config->Pulse; + + /* Write to TIMx CCER */ + TIMx->CCER = tmpccer; +} + +/** + * @brief Timer Output Compare 2 configuration + * @param TIMx to select the TIM peripheral + * @param OC_Config The ouput configuration structure + * @retval None + */ +void TIM_OC2_SetConfig(TIM_TypeDef* TIMx, TIM_OC_InitTypeDef* OC_Config) +{ + uint32_t tmpccmrx; + uint32_t tmpccer; + uint32_t tmpcr2; + + /* Disable the Channel 2: Reset the CC2E Bit */ + TIMx->CCER &= ~TIM_CCER_CC2E; + + /* Get the TIMx CCER register value */ + tmpccer = TIMx->CCER; + /* Get the TIMx CR2 register value */ + tmpcr2 = TIMx->CR2; + + /* Get the TIMx CCMR1 register value */ + tmpccmrx = TIMx->CCMR1; + + /* Reset the Output Compare mode and Capture/Compare selection Bits */ + tmpccmrx &= ~TIM_CCMR1_OC2M; + tmpccmrx &= ~TIM_CCMR1_CC2S; + + /* Select the Output Compare Mode */ + tmpccmrx |= (OC_Config->OCMode << 8U); + + /* Reset the Output Polarity level */ + tmpccer &= ~TIM_CCER_CC2P; + /* Set the Output Compare Polarity */ + tmpccer |= (OC_Config->OCPolarity << 4U); + + if (IS_TIM_CCXN_INSTANCE(TIMx, TIM_CHANNEL_2)) + { + assert_param(IS_TIM_OCN_POLARITY(OC_Config->OCNPolarity)); + + /* Reset the Output N Polarity level */ + tmpccer &= ~TIM_CCER_CC2NP; + /* Set the Output N Polarity */ + tmpccer |= (OC_Config->OCNPolarity << 4U); + /* Reset the Output N State */ + tmpccer &= ~TIM_CCER_CC2NE; + + } + + if (IS_TIM_BREAK_INSTANCE(TIMx)) + { + /* Check parameters */ + assert_param(IS_TIM_OCNIDLE_STATE(OC_Config->OCNIdleState)); + assert_param(IS_TIM_OCIDLE_STATE(OC_Config->OCIdleState)); + + /* Reset the Output Compare and Output Compare N IDLE State */ + tmpcr2 &= ~TIM_CR2_OIS2; + tmpcr2 &= ~TIM_CR2_OIS2N; + /* Set the Output Idle state */ + tmpcr2 |= (OC_Config->OCIdleState << 2U); + /* Set the Output N Idle state */ + tmpcr2 |= (OC_Config->OCNIdleState << 2U); + } + + /* Write to TIMx CR2 */ + TIMx->CR2 = tmpcr2; + + /* Write to TIMx CCMR1 */ + TIMx->CCMR1 = tmpccmrx; + + /* Set the Capture Compare Register value */ + TIMx->CCR2 = OC_Config->Pulse; + /* Write to TIMx CCER */ TIMx->CCER = tmpccer; } /** - * @brief Time Output Compare 3 configuration + * @brief Timer Output Compare 3 configuration * @param TIMx to select the TIM peripheral - * @param OC_Config: The output configuration structure + * @param OC_Config The ouput configuration structure * @retval None */ static void TIM_OC3_SetConfig(TIM_TypeDef* TIMx, TIM_OC_InitTypeDef* OC_Config) { - uint32_t tmpccmrx = 0U; - uint32_t tmpccer = 0U; - uint32_t tmpcr2 = 0U; + uint32_t tmpccmrx; + uint32_t tmpccer; + uint32_t tmpcr2; + /* Disable the Channel 3: Reset the CC2E Bit */ TIMx->CCER &= ~TIM_CCER_CC3E; + /* Get the TIMx CCER register value */ tmpccer = TIMx->CCER; /* Get the TIMx CR2 register value */ - tmpcr2 = TIMx->CR2; + tmpcr2 = TIMx->CR2; + /* Get the TIMx CCMR2 register value */ tmpccmrx = TIMx->CCMR2; + /* Reset the Output Compare mode and Capture/Compare selection Bits */ tmpccmrx &= ~TIM_CCMR2_OC3M; tmpccmrx &= ~TIM_CCMR2_CC3S; /* Select the Output Compare Mode */ tmpccmrx |= OC_Config->OCMode; + /* Reset the Output Polarity level */ tmpccer &= ~TIM_CCER_CC3P; /* Set the Output Compare Polarity */ tmpccer |= (OC_Config->OCPolarity << 8U); - if (IS_TIM_ADVANCED_INSTANCE(TIMx) != RESET) + if (IS_TIM_CCXN_INSTANCE(TIMx, TIM_CHANNEL_3)) { assert_param(IS_TIM_OCN_POLARITY(OC_Config->OCNPolarity)); - assert_param(IS_TIM_OCNIDLE_STATE(OC_Config->OCNIdleState)); - assert_param(IS_TIM_OCIDLE_STATE(OC_Config->OCIdleState)); + /* Reset the Output N Polarity level */ tmpccer &= ~TIM_CCER_CC3NP; /* Set the Output N Polarity */ tmpccer |= (OC_Config->OCNPolarity << 8U); /* Reset the Output N State */ tmpccer &= ~TIM_CCER_CC3NE; + } + + if (IS_TIM_BREAK_INSTANCE(TIMx)) + { + /* Check parameters */ + assert_param(IS_TIM_OCNIDLE_STATE(OC_Config->OCNIdleState)); + assert_param(IS_TIM_OCIDLE_STATE(OC_Config->OCIdleState)); + /* Reset the Output Compare and Output Compare N IDLE State */ tmpcr2 &= ~TIM_CR2_OIS3; tmpcr2 &= ~TIM_CR2_OIS3N; @@ -4591,86 +6182,103 @@ static void TIM_OC3_SetConfig(TIM_TypeDef* TIMx, TIM_OC_InitTypeDef* OC_Config) /* Write to TIMx CR2 */ TIMx->CR2 = tmpcr2; + /* Write to TIMx CCMR2 */ TIMx->CCMR2 = tmpccmrx; + /* Set the Capture Compare Register value */ TIMx->CCR3 = OC_Config->Pulse; + /* Write to TIMx CCER */ TIMx->CCER = tmpccer; } /** - * @brief Time Output Compare 4 configuration + * @brief Timer Output Compare 4 configuration * @param TIMx to select the TIM peripheral - * @param OC_Config: The output configuration structure + * @param OC_Config The ouput configuration structure * @retval None */ static void TIM_OC4_SetConfig(TIM_TypeDef* TIMx, TIM_OC_InitTypeDef* OC_Config) { - uint32_t tmpccmrx = 0U; - uint32_t tmpccer = 0U; - uint32_t tmpcr2 = 0U; + uint32_t tmpccmrx; + uint32_t tmpccer; + uint32_t tmpcr2; + /* Disable the Channel 4: Reset the CC4E Bit */ TIMx->CCER &= ~TIM_CCER_CC4E; + /* Get the TIMx CCER register value */ tmpccer = TIMx->CCER; /* Get the TIMx CR2 register value */ - tmpcr2 = TIMx->CR2; + tmpcr2 = TIMx->CR2; + /* Get the TIMx CCMR2 register value */ tmpccmrx = TIMx->CCMR2; + /* Reset the Output Compare mode and Capture/Compare selection Bits */ tmpccmrx &= ~TIM_CCMR2_OC4M; tmpccmrx &= ~TIM_CCMR2_CC4S; + /* Select the Output Compare Mode */ tmpccmrx |= (OC_Config->OCMode << 8U); + /* Reset the Output Polarity level */ tmpccer &= ~TIM_CCER_CC4P; /* Set the Output Compare Polarity */ tmpccer |= (OC_Config->OCPolarity << 12U); - /*if((TIMx == TIM1) || (TIMx == TIM8))*/ - if (IS_TIM_ADVANCED_INSTANCE(TIMx) != RESET) + if (IS_TIM_BREAK_INSTANCE(TIMx)) { + /* Check parameters */ assert_param(IS_TIM_OCIDLE_STATE(OC_Config->OCIdleState)); + /* Reset the Output Compare IDLE State */ tmpcr2 &= ~TIM_CR2_OIS4; + /* Set the Output Idle state */ tmpcr2 |= (OC_Config->OCIdleState << 6U); } /* Write to TIMx CR2 */ TIMx->CR2 = tmpcr2; + /* Write to TIMx CCMR2 */ TIMx->CCMR2 = tmpccmrx; + /* Set the Capture Compare Register value */ TIMx->CCR4 = OC_Config->Pulse; + /* Write to TIMx CCER */ TIMx->CCER = tmpccer; } /** - * @brief Time Output Compare 4 configuration - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param sSlaveConfig: The slave configuration structure + * @brief Slave Timer configuration function + * @param htim TIM handle + * @param sSlaveConfig Slave timer configuration * @retval None */ -static void TIM_SlaveTimer_SetConfig(TIM_HandleTypeDef* htim, - TIM_SlaveConfigTypeDef* sSlaveConfig) +static HAL_StatusTypeDef TIM_SlaveTimer_SetConfig(TIM_HandleTypeDef* htim, + TIM_SlaveConfigTypeDef* sSlaveConfig) { - uint32_t tmpsmcr = 0U; - uint32_t tmpccmr1 = 0U; - uint32_t tmpccer = 0U; + uint32_t tmpsmcr; + uint32_t tmpccmr1; + uint32_t tmpccer; + /* Get the TIMx SMCR register value */ tmpsmcr = htim->Instance->SMCR; + /* Reset the Trigger Selection Bits */ tmpsmcr &= ~TIM_SMCR_TS; /* Set the Input Trigger source */ tmpsmcr |= sSlaveConfig->InputTrigger; + /* Reset the slave mode Bits */ tmpsmcr &= ~TIM_SMCR_SMS; /* Set the slave mode */ tmpsmcr |= sSlaveConfig->SlaveMode; + /* Write to TIMx SMCR */ htim->Instance->SMCR = tmpsmcr; @@ -4680,7 +6288,7 @@ static void TIM_SlaveTimer_SetConfig(TIM_HandleTypeDef* htim, case TIM_TS_ETRF: { /* Check the parameters */ - assert_param(IS_TIM_ETR_INSTANCE(htim->Instance)); + assert_param(IS_TIM_CLOCKSOURCE_ETRMODE1_INSTANCE(htim->Instance)); assert_param(IS_TIM_TRIGGERPRESCALER(sSlaveConfig->TriggerPrescaler)); assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity)); assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter)); @@ -4689,26 +6297,34 @@ static void TIM_SlaveTimer_SetConfig(TIM_HandleTypeDef* htim, sSlaveConfig->TriggerPrescaler, sSlaveConfig->TriggerPolarity, sSlaveConfig->TriggerFilter); + break; } - break; case TIM_TS_TI1F_ED: { /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter)); + + if (sSlaveConfig->SlaveMode == TIM_SLAVEMODE_GATED) + { + return HAL_ERROR; + } + /* Disable the Channel 1: Reset the CC1E Bit */ tmpccer = htim->Instance->CCER; htim->Instance->CCER &= ~TIM_CCER_CC1E; tmpccmr1 = htim->Instance->CCMR1; + /* Set the filter */ tmpccmr1 &= ~TIM_CCMR1_IC1F; tmpccmr1 |= ((sSlaveConfig->TriggerFilter) << 4U); + /* Write to TIMx CCMR1 and CCER registers */ htim->Instance->CCMR1 = tmpccmr1; htim->Instance->CCER = tmpccer; + break; } - break; case TIM_TS_TI1FP1: { @@ -4716,12 +6332,13 @@ static void TIM_SlaveTimer_SetConfig(TIM_HandleTypeDef* htim, assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity)); assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter)); + /* Configure TI1 Filter and Polarity */ TIM_TI1_ConfigInputStage(htim->Instance, sSlaveConfig->TriggerPolarity, sSlaveConfig->TriggerFilter); + break; } - break; case TIM_TS_TI2FP2: { @@ -4729,73 +6346,116 @@ static void TIM_SlaveTimer_SetConfig(TIM_HandleTypeDef* htim, assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity)); assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter)); + /* Configure TI2 Filter and Polarity */ TIM_TI2_ConfigInputStage(htim->Instance, sSlaveConfig->TriggerPolarity, sSlaveConfig->TriggerFilter); + break; } - break; case TIM_TS_ITR0: - { - /* Check the parameter */ - assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); - } - break; - case TIM_TS_ITR1: - { - /* Check the parameter */ - assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); - } - break; - case TIM_TS_ITR2: - { - /* Check the parameter */ - assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); - } - break; - case TIM_TS_ITR3: { /* Check the parameter */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); + break; } - break; default: break; } + + return HAL_OK; } +/** + * @brief Configure the TI1 as Input. + * @param TIMx to select the TIM peripheral. + * @param TIM_ICPolarity The Input Polarity. + * This parameter can be one of the following values: + * @arg TIM_ICPOLARITY_RISING + * @arg TIM_ICPOLARITY_FALLING + * @arg TIM_ICPOLARITY_BOTHEDGE + * @param TIM_ICSelection specifies the input to be used. + * This parameter can be one of the following values: + * @arg TIM_ICSELECTION_DIRECTTI: TIM Input 1 is selected to be connected to IC1. + * @arg TIM_ICSELECTION_INDIRECTTI: TIM Input 1 is selected to be connected to IC2. + * @arg TIM_ICSELECTION_TRC: TIM Input 1 is selected to be connected to TRC. + * @param TIM_ICFilter Specifies the Input Capture Filter. + * This parameter must be a value between 0x00 and 0x0F. + * @retval None + * @note TIM_ICFilter and TIM_ICPolarity are not used in INDIRECT mode as TI2FP1 + * (on channel2 path) is used as the input signal. Therefore CCMR1 must be + * protected against un-initialized filter and polarity values. + */ +void TIM_TI1_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, + uint32_t TIM_ICFilter) +{ + uint32_t tmpccmr1; + uint32_t tmpccer; + + /* Disable the Channel 1: Reset the CC1E Bit */ + TIMx->CCER &= ~TIM_CCER_CC1E; + tmpccmr1 = TIMx->CCMR1; + tmpccer = TIMx->CCER; + + /* Select the Input */ + if (IS_TIM_CC2_INSTANCE(TIMx) != RESET) + { + tmpccmr1 &= ~TIM_CCMR1_CC1S; + tmpccmr1 |= TIM_ICSelection; + } + else + { + tmpccmr1 |= TIM_CCMR1_CC1S_0; + } + + /* Set the filter */ + tmpccmr1 &= ~TIM_CCMR1_IC1F; + tmpccmr1 |= ((TIM_ICFilter << 4U) & TIM_CCMR1_IC1F); + + /* Select the Polarity and set the CC1E Bit */ + tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC1NP); + tmpccer |= (TIM_ICPolarity & (TIM_CCER_CC1P | TIM_CCER_CC1NP)); + + /* Write to TIMx CCMR1 and CCER registers */ + TIMx->CCMR1 = tmpccmr1; + TIMx->CCER = tmpccer; +} /** * @brief Configure the Polarity and Filter for TI1. * @param TIMx to select the TIM peripheral. - * @param TIM_ICPolarity : The Input Polarity. + * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: - * @arg TIM_ICPolarity_Rising - * @arg TIM_ICPolarity_Falling - * @arg TIM_ICPolarity_BothEdge - * @param TIM_ICFilter: Specifies the Input Capture Filter. + * @arg TIM_ICPOLARITY_RISING + * @arg TIM_ICPOLARITY_FALLING + * @arg TIM_ICPOLARITY_BOTHEDGE + * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. * @retval None */ static void TIM_TI1_ConfigInputStage(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter) { - uint32_t tmpccmr1 = 0U; - uint32_t tmpccer = 0U; + uint32_t tmpccmr1; + uint32_t tmpccer; + /* Disable the Channel 1: Reset the CC1E Bit */ tmpccer = TIMx->CCER; TIMx->CCER &= ~TIM_CCER_CC1E; tmpccmr1 = TIMx->CCMR1; + /* Set the filter */ tmpccmr1 &= ~TIM_CCMR1_IC1F; tmpccmr1 |= (TIM_ICFilter << 4U); + /* Select the Polarity and set the CC1E Bit */ tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC1NP); tmpccer |= TIM_ICPolarity; + /* Write to TIMx CCMR1 and CCER registers */ TIMx->CCMR1 = tmpccmr1; TIMx->CCER = tmpccer; @@ -4804,41 +6464,46 @@ static void TIM_TI1_ConfigInputStage(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, /** * @brief Configure the TI2 as Input. * @param TIMx to select the TIM peripheral - * @param TIM_ICPolarity : The Input Polarity. + * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: - * @arg TIM_ICPolarity_Rising - * @arg TIM_ICPolarity_Falling - * @arg TIM_ICPolarity_BothEdge - * @param TIM_ICSelection: specifies the input to be used. + * @arg TIM_ICPOLARITY_RISING + * @arg TIM_ICPOLARITY_FALLING + * @arg TIM_ICPOLARITY_BOTHEDGE + * @param TIM_ICSelection specifies the input to be used. * This parameter can be one of the following values: - * @arg TIM_ICSelection_DirectTI: TIM Input 2 is selected to be connected to IC2. - * @arg TIM_ICSelection_IndirectTI: TIM Input 2 is selected to be connected to IC1. - * @arg TIM_ICSelection_TRC: TIM Input 2 is selected to be connected to TRC. - * @param TIM_ICFilter: Specifies the Input Capture Filter. + * @arg TIM_ICSELECTION_DIRECTTI: TIM Input 2 is selected to be connected to IC2. + * @arg TIM_ICSELECTION_INDIRECTTI: TIM Input 2 is selected to be connected to IC1. + * @arg TIM_ICSELECTION_TRC: TIM Input 2 is selected to be connected to TRC. + * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. + * @retval None * @note TIM_ICFilter and TIM_ICPolarity are not used in INDIRECT mode as TI1FP2 * (on channel1 path) is used as the input signal. Therefore CCMR1 must be * protected against un-initialized filter and polarity values. - * @retval None */ static void TIM_TI2_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter) { - uint32_t tmpccmr1 = 0U; - uint32_t tmpccer = 0U; + uint32_t tmpccmr1; + uint32_t tmpccer; + /* Disable the Channel 2: Reset the CC2E Bit */ TIMx->CCER &= ~TIM_CCER_CC2E; tmpccmr1 = TIMx->CCMR1; tmpccer = TIMx->CCER; + /* Select the Input */ tmpccmr1 &= ~TIM_CCMR1_CC2S; tmpccmr1 |= (TIM_ICSelection << 8U); + /* Set the filter */ tmpccmr1 &= ~TIM_CCMR1_IC2F; tmpccmr1 |= ((TIM_ICFilter << 12U) & TIM_CCMR1_IC2F); + /* Select the Polarity and set the CC2E Bit */ tmpccer &= ~(TIM_CCER_CC2P | TIM_CCER_CC2NP); tmpccer |= ((TIM_ICPolarity << 4U) & (TIM_CCER_CC2P | TIM_CCER_CC2NP)); + /* Write to TIMx CCMR1 and CCER registers */ TIMx->CCMR1 = tmpccmr1 ; TIMx->CCER = tmpccer; @@ -4847,29 +6512,33 @@ static void TIM_TI2_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32 /** * @brief Configure the Polarity and Filter for TI2. * @param TIMx to select the TIM peripheral. - * @param TIM_ICPolarity : The Input Polarity. + * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: - * @arg TIM_ICPolarity_Rising - * @arg TIM_ICPolarity_Falling - * @arg TIM_ICPolarity_BothEdge - * @param TIM_ICFilter: Specifies the Input Capture Filter. + * @arg TIM_ICPOLARITY_RISING + * @arg TIM_ICPOLARITY_FALLING + * @arg TIM_ICPOLARITY_BOTHEDGE + * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. * @retval None */ static void TIM_TI2_ConfigInputStage(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter) { - uint32_t tmpccmr1 = 0U; - uint32_t tmpccer = 0U; + uint32_t tmpccmr1; + uint32_t tmpccer; + /* Disable the Channel 2: Reset the CC2E Bit */ TIMx->CCER &= ~TIM_CCER_CC2E; tmpccmr1 = TIMx->CCMR1; tmpccer = TIMx->CCER; + /* Set the filter */ tmpccmr1 &= ~TIM_CCMR1_IC2F; tmpccmr1 |= (TIM_ICFilter << 12U); + /* Select the Polarity and set the CC2E Bit */ tmpccer &= ~(TIM_CCER_CC2P | TIM_CCER_CC2NP); tmpccer |= (TIM_ICPolarity << 4U); + /* Write to TIMx CCMR1 and CCER registers */ TIMx->CCMR1 = tmpccmr1 ; TIMx->CCER = tmpccer; @@ -4878,41 +6547,45 @@ static void TIM_TI2_ConfigInputStage(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, /** * @brief Configure the TI3 as Input. * @param TIMx to select the TIM peripheral - * @param TIM_ICPolarity : The Input Polarity. + * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: - * @arg TIM_ICPolarity_Rising - * @arg TIM_ICPolarity_Falling - * @arg TIM_ICPolarity_BothEdge - * @param TIM_ICSelection: specifies the input to be used. + * @arg TIM_ICPOLARITY_RISING + * @arg TIM_ICPOLARITY_FALLING + * @param TIM_ICSelection specifies the input to be used. * This parameter can be one of the following values: - * @arg TIM_ICSelection_DirectTI: TIM Input 3 is selected to be connected to IC3. - * @arg TIM_ICSelection_IndirectTI: TIM Input 3 is selected to be connected to IC4. - * @arg TIM_ICSelection_TRC: TIM Input 3 is selected to be connected to TRC. - * @param TIM_ICFilter: Specifies the Input Capture Filter. + * @arg TIM_ICSELECTION_DIRECTTI: TIM Input 3 is selected to be connected to IC3. + * @arg TIM_ICSELECTION_INDIRECTTI: TIM Input 3 is selected to be connected to IC4. + * @arg TIM_ICSELECTION_TRC: TIM Input 3 is selected to be connected to TRC. + * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. - * @note TIM_ICFilter and TIM_ICPolarity are not used in INDIRECT mode as TI4FP3 - * (on channel4 path) is used as the input signal. Therefore CCMR2 must be - * protected against un-initialized filter and polarity values. * @retval None + * @note TIM_ICFilter and TIM_ICPolarity are not used in INDIRECT mode as TI3FP4 + * (on channel1 path) is used as the input signal. Therefore CCMR2 must be + * protected against un-initialized filter and polarity values. */ static void TIM_TI3_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter) { - uint32_t tmpccmr2 = 0U; - uint32_t tmpccer = 0U; + uint32_t tmpccmr2; + uint32_t tmpccer; + /* Disable the Channel 3: Reset the CC3E Bit */ TIMx->CCER &= ~TIM_CCER_CC3E; tmpccmr2 = TIMx->CCMR2; tmpccer = TIMx->CCER; + /* Select the Input */ tmpccmr2 &= ~TIM_CCMR2_CC3S; tmpccmr2 |= TIM_ICSelection; + /* Set the filter */ tmpccmr2 &= ~TIM_CCMR2_IC3F; tmpccmr2 |= ((TIM_ICFilter << 4U) & TIM_CCMR2_IC3F); + /* Select the Polarity and set the CC3E Bit */ - tmpccer &= ~(TIM_CCER_CC3P | TIM_CCER_CC3NP); - tmpccer |= ((TIM_ICPolarity << 8U) & (TIM_CCER_CC3P | TIM_CCER_CC3NP)); + tmpccer &= ~(TIM_CCER_CC3P); + tmpccer |= ((TIM_ICPolarity << 8U) & TIM_CCER_CC3P); + /* Write to TIMx CCMR2 and CCER registers */ TIMx->CCMR2 = tmpccmr2; TIMx->CCER = tmpccer; @@ -4921,41 +6594,45 @@ static void TIM_TI3_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32 /** * @brief Configure the TI4 as Input. * @param TIMx to select the TIM peripheral - * @param TIM_ICPolarity : The Input Polarity. + * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: - * @arg TIM_ICPolarity_Rising - * @arg TIM_ICPolarity_Falling - * @arg TIM_ICPolarity_BothEdge - * @param TIM_ICSelection: specifies the input to be used. + * @arg TIM_ICPOLARITY_RISING + * @arg TIM_ICPOLARITY_FALLING + * @param TIM_ICSelection specifies the input to be used. * This parameter can be one of the following values: - * @arg TIM_ICSelection_DirectTI: TIM Input 4 is selected to be connected to IC4. - * @arg TIM_ICSelection_IndirectTI: TIM Input 4 is selected to be connected to IC3. - * @arg TIM_ICSelection_TRC: TIM Input 4 is selected to be connected to TRC. - * @param TIM_ICFilter: Specifies the Input Capture Filter. + * @arg TIM_ICSELECTION_DIRECTTI: TIM Input 4 is selected to be connected to IC4. + * @arg TIM_ICSELECTION_INDIRECTTI: TIM Input 4 is selected to be connected to IC3. + * @arg TIM_ICSELECTION_TRC: TIM Input 4 is selected to be connected to TRC. + * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. - * @note TIM_ICFilter and TIM_ICPolarity are not used in INDIRECT mode as TI3FP4 - * (on channel3 path) is used as the input signal. Therefore CCMR2 must be + * @note TIM_ICFilter and TIM_ICPolarity are not used in INDIRECT mode as TI4FP3 + * (on channel1 path) is used as the input signal. Therefore CCMR2 must be * protected against un-initialized filter and polarity values. * @retval None */ static void TIM_TI4_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter) { - uint32_t tmpccmr2 = 0U; - uint32_t tmpccer = 0U; + uint32_t tmpccmr2; + uint32_t tmpccer; + /* Disable the Channel 4: Reset the CC4E Bit */ TIMx->CCER &= ~TIM_CCER_CC4E; tmpccmr2 = TIMx->CCMR2; tmpccer = TIMx->CCER; + /* Select the Input */ tmpccmr2 &= ~TIM_CCMR2_CC4S; tmpccmr2 |= (TIM_ICSelection << 8U); + /* Set the filter */ tmpccmr2 &= ~TIM_CCMR2_IC4F; tmpccmr2 |= ((TIM_ICFilter << 12U) & TIM_CCMR2_IC4F); + /* Select the Polarity and set the CC4E Bit */ - tmpccer &= ~(TIM_CCER_CC4P | TIM_CCER_CC4NP); - tmpccer |= ((TIM_ICPolarity << 12U) & (TIM_CCER_CC4P | TIM_CCER_CC4NP)); + tmpccer &= ~(TIM_CCER_CC4P); + tmpccer |= ((TIM_ICPolarity << 12U) & TIM_CCER_CC4P); + /* Write to TIMx CCMR2 and CCER registers */ TIMx->CCMR2 = tmpccmr2; TIMx->CCER = tmpccer ; @@ -4964,7 +6641,7 @@ static void TIM_TI4_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32 /** * @brief Selects the Input Trigger source * @param TIMx to select the TIM peripheral - * @param TIM_ITRx: The Input Trigger source. + * @param InputTriggerSource The Input Trigger source. * This parameter can be one of the following values: * @arg TIM_TS_ITR0: Internal Trigger 0 * @arg TIM_TS_ITR1: Internal Trigger 1 @@ -4976,49 +6653,109 @@ static void TIM_TI4_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32 * @arg TIM_TS_ETRF: External Trigger input * @retval None */ -static void TIM_ITRx_SetConfig(TIM_TypeDef* TIMx, uint16_t TIM_ITRx) +static void TIM_ITRx_SetConfig(TIM_TypeDef* TIMx, uint32_t InputTriggerSource) { - uint32_t tmpsmcr = 0U; + uint32_t tmpsmcr; + /* Get the TIMx SMCR register value */ tmpsmcr = TIMx->SMCR; /* Reset the TS Bits */ tmpsmcr &= ~TIM_SMCR_TS; /* Set the Input Trigger source and the slave mode*/ - tmpsmcr |= TIM_ITRx | TIM_SLAVEMODE_EXTERNAL1; + tmpsmcr |= (InputTriggerSource | TIM_SLAVEMODE_EXTERNAL1); /* Write to TIMx SMCR */ TIMx->SMCR = tmpsmcr; } - /** * @brief Configures the TIMx External Trigger (ETR). * @param TIMx to select the TIM peripheral - * @param TIM_ExtTRGPrescaler: The external Trigger Prescaler. + * @param TIM_ExtTRGPrescaler The external Trigger Prescaler. * This parameter can be one of the following values: - * @arg TIM_ETRPRESCALER_DIV1 : ETRP Prescaler OFF. - * @arg TIM_ETRPRESCALER_DIV2 : ETRP frequency divided by 2. - * @arg TIM_ETRPRESCALER_DIV4 : ETRP frequency divided by 4. - * @arg TIM_ETRPRESCALER_DIV8 : ETRP frequency divided by 8. - * @param TIM_ExtTRGPolarity: The external Trigger Polarity. + * @arg TIM_ETRPRESCALER_DIV1: ETRP Prescaler OFF. + * @arg TIM_ETRPRESCALER_DIV2: ETRP frequency divided by 2. + * @arg TIM_ETRPRESCALER_DIV4: ETRP frequency divided by 4. + * @arg TIM_ETRPRESCALER_DIV8: ETRP frequency divided by 8. + * @param TIM_ExtTRGPolarity The external Trigger Polarity. * This parameter can be one of the following values: - * @arg TIM_ETRPOLARITY_INVERTED : active low or falling edge active. - * @arg TIM_ETRPOLARITY_NONINVERTED : active high or rising edge active. - * @param ExtTRGFilter: External Trigger Filter. + * @arg TIM_ETRPOLARITY_INVERTED: active low or falling edge active. + * @arg TIM_ETRPOLARITY_NONINVERTED: active high or rising edge active. + * @param ExtTRGFilter External Trigger Filter. * This parameter must be a value between 0x00 and 0x0F * @retval None */ -static void TIM_ETR_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ExtTRGPrescaler, - uint32_t TIM_ExtTRGPolarity, uint32_t ExtTRGFilter) +void TIM_ETR_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ExtTRGPrescaler, + uint32_t TIM_ExtTRGPolarity, uint32_t ExtTRGFilter) { - uint32_t tmpsmcr = 0U; + uint32_t tmpsmcr; + tmpsmcr = TIMx->SMCR; + /* Reset the ETR Bits */ tmpsmcr &= ~(TIM_SMCR_ETF | TIM_SMCR_ETPS | TIM_SMCR_ECE | TIM_SMCR_ETP); + /* Set the Prescaler, the Filter value and the Polarity */ - tmpsmcr |= (uint32_t)(TIM_ExtTRGPrescaler | (TIM_ExtTRGPolarity | (ExtTRGFilter << 8))); + tmpsmcr |= (uint32_t)(TIM_ExtTRGPrescaler | (TIM_ExtTRGPolarity | (ExtTRGFilter << 8U))); + /* Write to TIMx SMCR */ TIMx->SMCR = tmpsmcr; } +/** + * @brief Enables or disables the TIM Capture Compare Channel x. + * @param TIMx to select the TIM peripheral + * @param Channel specifies the TIM Channel + * This parameter can be one of the following values: + * @arg TIM_CHANNEL_1: TIM Channel 1 + * @arg TIM_CHANNEL_2: TIM Channel 2 + * @arg TIM_CHANNEL_3: TIM Channel 3 + * @arg TIM_CHANNEL_4: TIM Channel 4 + * @param ChannelState specifies the TIM Channel CCxE bit new state. + * This parameter can be: TIM_CCx_ENABLE or TIM_CCx_DISABLE. + * @retval None + */ +void TIM_CCxChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelState) +{ + uint32_t tmp; + + /* Check the parameters */ + assert_param(IS_TIM_CC1_INSTANCE(TIMx)); + assert_param(IS_TIM_CHANNELS(Channel)); + + tmp = TIM_CCER_CC1E << (Channel & 0x1FU); /* 0x1FU = 31 bits max shift */ + + /* Reset the CCxE Bit */ + TIMx->CCER &= ~tmp; + + /* Set or reset the CCxE Bit */ + TIMx->CCER |= (uint32_t)(ChannelState << (Channel & 0x1FU)); /* 0x1FU = 31 bits max shift */ +} + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) +/** + * @brief Reset interrupt callbacks to the legacy weak callbacks. + * @param htim pointer to a TIM_HandleTypeDef structure that contains + * the configuration information for TIM module. + * @retval None + */ +void TIM_ResetCallback(TIM_HandleTypeDef* htim) +{ + /* Reset the TIM callback to the legacy weak callbacks */ + htim->PeriodElapsedCallback = HAL_TIM_PeriodElapsedCallback; /* Legacy weak PeriodElapsedCallback */ + htim->PeriodElapsedHalfCpltCallback = HAL_TIM_PeriodElapsedHalfCpltCallback; /* Legacy weak PeriodElapsedHalfCpltCallback */ + htim->TriggerCallback = HAL_TIM_TriggerCallback; /* Legacy weak TriggerCallback */ + htim->TriggerHalfCpltCallback = HAL_TIM_TriggerHalfCpltCallback; /* Legacy weak TriggerHalfCpltCallback */ + htim->IC_CaptureCallback = HAL_TIM_IC_CaptureCallback; /* Legacy weak IC_CaptureCallback */ + htim->IC_CaptureHalfCpltCallback = HAL_TIM_IC_CaptureHalfCpltCallback; /* Legacy weak IC_CaptureHalfCpltCallback */ + htim->OC_DelayElapsedCallback = HAL_TIM_OC_DelayElapsedCallback; /* Legacy weak OC_DelayElapsedCallback */ + htim->PWM_PulseFinishedCallback = HAL_TIM_PWM_PulseFinishedCallback; /* Legacy weak PWM_PulseFinishedCallback */ + htim->PWM_PulseFinishedHalfCpltCallback = HAL_TIM_PWM_PulseFinishedHalfCpltCallback; /* Legacy weak PWM_PulseFinishedHalfCpltCallback */ + htim->ErrorCallback = HAL_TIM_ErrorCallback; /* Legacy weak ErrorCallback */ + htim->CommutationCallback = HAL_TIMEx_CommutCallback; /* Legacy weak CommutationCallback */ + htim->CommutationHalfCpltCallback = HAL_TIMEx_CommutHalfCpltCallback; /* Legacy weak CommutationHalfCpltCallback */ + htim->BreakCallback = HAL_TIMEx_BreakCallback; /* Legacy weak BreakCallback */ +} +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + /** * @} */ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim_ex.c b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_tim_ex.c similarity index 65% rename from EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim_ex.c rename to EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_tim_ex.c index c030b91b..6fc8dce0 100644 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim_ex.c +++ b/EpsilonLights/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_tim_ex.c @@ -1,24 +1,22 @@ /** ****************************************************************************** - * @file stm32f4xx_hal_tim_ex.c + * @file stm32f1xx_hal_tim_ex.c * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 * @brief TIM HAL module driver. * This file provides firmware functions to manage the following - * functionalities of the Timer extension peripheral: + * functionalities of the Timer Extended peripheral: * + Time Hall Sensor Interface Initialization * + Time Hall Sensor Interface Start - * + Time Complementary signal bread and dead time configuration + * + Time Complementary signal break and dead time configuration * + Time Master and Slave synchronization configuration + * + Timer remapping capabilities configuration @verbatim ============================================================================== ##### TIMER Extended features ##### ============================================================================== [..] - The Timer Extension features include: + The Timer Extended features include: (#) Complementary outputs with programmable dead-time for : - (++) Input Capture (++) Output Compare (++) PWM generation (Edge and Center-aligned Mode) (++) One-pulse mode output @@ -28,21 +26,18 @@ (#) Supports incremental (quadrature) encoder and hall-sensor circuitry for positioning purposes - ##### How to use this driver ##### + ##### How to use this driver ##### ============================================================================== - [..] + [..] (#) Initialize the TIM low level resources by implementing the following functions - depending from feature used : - (++) Complementary Output Compare : HAL_TIM_OC_MspInit() - (++) Complementary PWM generation : HAL_TIM_PWM_MspInit() - (++) Complementary One-pulse mode output : HAL_TIM_OnePulse_MspInit() - (++) Hall Sensor output : HAL_TIM_HallSensor_MspInit() + depending on the selected feature: + (++) Hall Sensor output : HAL_TIMEx_HallSensor_MspInit() (#) Initialize the TIM low level resources : - (##) Enable the TIM interface clock using __TIMx_CLK_ENABLE(); + (##) Enable the TIM interface clock using __HAL_RCC_TIMx_CLK_ENABLE(); (##) TIM pins configuration (+++) Enable the clock for the TIM GPIOs using the following function: - __GPIOx_CLK_ENABLE(); + __HAL_RCC_GPIOx_CLK_ENABLE(); (+++) Configure these TIM pins in Alternate function mode using HAL_GPIO_Init(); (#) The external Clock can be configured, if needed (the default clock is the @@ -50,61 +45,44 @@ HAL_TIM_ConfigClockSource, the clock configuration should be done before any start function. - (#) Configure the TIM in the desired functioning mode using one of the - initialization function of this driver: - (++) HAL_TIMEx_HallSensor_Init and HAL_TIMEx_ConfigCommutationEvent: to use the - Timer Hall Sensor Interface and the commutation event with the corresponding - Interrupt and DMA request if needed (Note that One Timer is used to interface - with the Hall sensor Interface and another Timer should be used to use - the commutation event). + (#) Configure the TIM in the desired functioning mode using one of the + initialization function of this driver: + (++) HAL_TIMEx_HallSensor_Init() and HAL_TIMEx_ConfigCommutEvent(): to use the + Timer Hall Sensor Interface and the commutation event with the corresponding + Interrupt and DMA request if needed (Note that One Timer is used to interface + with the Hall sensor Interface and another Timer should be used to use + the commutation event). - (#) Activate the TIM peripheral using one of the start functions: + (#) Activate the TIM peripheral using one of the start functions: (++) Complementary Output Compare : HAL_TIMEx_OCN_Start(), HAL_TIMEx_OCN_Start_DMA(), HAL_TIMEx_OC_Start_IT() (++) Complementary PWM generation : HAL_TIMEx_PWMN_Start(), HAL_TIMEx_PWMN_Start_DMA(), HAL_TIMEx_PWMN_Start_IT() (++) Complementary One-pulse mode output : HAL_TIMEx_OnePulseN_Start(), HAL_TIMEx_OnePulseN_Start_IT() (++) Hall Sensor output : HAL_TIMEx_HallSensor_Start(), HAL_TIMEx_HallSensor_Start_DMA(), HAL_TIMEx_HallSensor_Start_IT(). - @endverbatim ****************************************************************************** * @attention * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

* - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause * ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" +#include "stm32f1xx_hal.h" -/** @addtogroup STM32F4xx_HAL_Driver +/** @addtogroup STM32F1xx_HAL_Driver * @{ */ -/** @defgroup TIMEx TIMEx - * @brief TIM HAL module driver +/** @defgroup TIMEx TIMEx + * @brief TIM Extended HAL module driver * @{ */ @@ -114,23 +92,17 @@ /* Private define ------------------------------------------------------------*/ /* Private macro -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ -/** @addtogroup TIMEx_Private_Functions - * @{ - */ /* Private function prototypes -----------------------------------------------*/ static void TIM_CCxNChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelNState); -/** - * @} - */ /* Exported functions --------------------------------------------------------*/ -/** @defgroup TIMEx_Exported_Functions TIM Exported Functions +/** @defgroup TIMEx_Exported_Functions TIM Extended Exported Functions * @{ */ -/** @defgroup TIMEx_Exported_Functions_Group1 Timer Hall Sensor functions - * @brief Timer Hall Sensor functions - * +/** @defgroup TIMEx_Exported_Functions_Group1 Extended Timer Hall Sensor functions + * @brief Timer Hall Sensor functions + * @verbatim ============================================================================== ##### Timer Hall Sensor functions ##### @@ -150,10 +122,9 @@ static void TIM_CCxNChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t Cha * @{ */ /** - * @brief Initializes the TIM Hall Sensor Interface and create the associated handle. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param sConfig: TIM Hall Sensor configuration structure + * @brief Initializes the TIM Hall Sensor Interface and initialize the associated handle. + * @param htim TIM Hall Sensor Interface handle + * @param sConfig TIM Hall Sensor configuration structure * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef* htim, TIM_HallSensor_InitTypeDef* sConfig) @@ -166,32 +137,62 @@ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef* htim, TIM_HallSen return HAL_ERROR; } - assert_param(IS_TIM_XOR_INSTANCE(htim->Instance)); + /* Check the parameters */ + assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); + assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload)); assert_param(IS_TIM_IC_POLARITY(sConfig->IC1Polarity)); assert_param(IS_TIM_IC_PRESCALER(sConfig->IC1Prescaler)); assert_param(IS_TIM_IC_FILTER(sConfig->IC1Filter)); + + if (htim->State == HAL_TIM_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + htim->Lock = HAL_UNLOCKED; + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + /* Reset interrupt callbacks to legacy week callbacks */ + TIM_ResetCallback(htim); + + if (htim->HallSensor_MspInitCallback == NULL) + { + htim->HallSensor_MspInitCallback = HAL_TIMEx_HallSensor_MspInit; + } + + /* Init the low level hardware : GPIO, CLOCK, NVIC */ + htim->HallSensor_MspInitCallback(htim); +#else + /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ + HAL_TIMEx_HallSensor_MspInit(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + } + /* Set the TIM state */ htim->State = HAL_TIM_STATE_BUSY; - /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ - HAL_TIMEx_HallSensor_MspInit(htim); + /* Configure the Time base in the Encoder Mode */ TIM_Base_SetConfig(htim->Instance, &htim->Init); + /* Configure the Channel 1 as Input Channel to interface with the three Outputs of the Hall sensor */ TIM_TI1_SetConfig(htim->Instance, sConfig->IC1Polarity, TIM_ICSELECTION_TRC, sConfig->IC1Filter); + /* Reset the IC1PSC Bits */ htim->Instance->CCMR1 &= ~TIM_CCMR1_IC1PSC; /* Set the IC1PSC value */ htim->Instance->CCMR1 |= sConfig->IC1Prescaler; + /* Enable the Hall sensor interface (XOR function of the three inputs) */ htim->Instance->CR2 |= TIM_CR2_TI1S; + /* Select the TIM_TS_TI1F_ED signal as Input trigger for the TIM */ htim->Instance->SMCR &= ~TIM_SMCR_TS; htim->Instance->SMCR |= TIM_TS_TI1F_ED; + /* Use the TIM_TS_TI1F_ED signal to reset the TIM counter each edge detection */ htim->Instance->SMCR &= ~TIM_SMCR_SMS; htim->Instance->SMCR |= TIM_SLAVEMODE_RESET; + /* Program channel 2 in PWM 2 mode with the desired Commutation_Delay*/ OC_Config.OCFastMode = TIM_OCFAST_DISABLE; OC_Config.OCIdleState = TIM_OCIDLESTATE_RESET; @@ -200,166 +201,211 @@ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef* htim, TIM_HallSen OC_Config.OCNPolarity = TIM_OCNPOLARITY_HIGH; OC_Config.OCPolarity = TIM_OCPOLARITY_HIGH; OC_Config.Pulse = sConfig->Commutation_Delay; + TIM_OC2_SetConfig(htim->Instance, &OC_Config); + /* Select OC2REF as trigger output on TRGO: write the MMS bits in the TIMx_CR2 register to 101 */ htim->Instance->CR2 &= ~TIM_CR2_MMS; htim->Instance->CR2 |= TIM_TRGO_OC2REF; + /* Initialize the TIM state*/ htim->State = HAL_TIM_STATE_READY; + return HAL_OK; } /** * @brief DeInitializes the TIM Hall Sensor interface - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Hall Sensor Interface handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_HallSensor_DeInit(TIM_HandleTypeDef* htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); + htim->State = HAL_TIM_STATE_BUSY; + /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + + if (htim->HallSensor_MspDeInitCallback == NULL) + { + htim->HallSensor_MspDeInitCallback = HAL_TIMEx_HallSensor_MspDeInit; + } + + /* DeInit the low level hardware */ + htim->HallSensor_MspDeInitCallback(htim); +#else /* DeInit the low level hardware: GPIO, CLOCK, NVIC */ HAL_TIMEx_HallSensor_MspDeInit(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; + /* Release Lock */ __HAL_UNLOCK(htim); + return HAL_OK; } /** * @brief Initializes the TIM Hall Sensor MSP. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Hall Sensor Interface handle * @retval None */ __weak void HAL_TIMEx_HallSensor_MspInit(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, + + /* NOTE : This function should not be modified, when the callback is needed, the HAL_TIMEx_HallSensor_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM Hall Sensor MSP. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Hall Sensor Interface handle * @retval None */ __weak void HAL_TIMEx_HallSensor_MspDeInit(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, + + /* NOTE : This function should not be modified, when the callback is needed, the HAL_TIMEx_HallSensor_MspDeInit could be implemented in the user file */ } /** * @brief Starts the TIM Hall Sensor Interface. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Hall Sensor Interface handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start(TIM_HandleTypeDef* htim) { + uint32_t tmpsmcr; + /* Check the parameters */ - assert_param(IS_TIM_XOR_INSTANCE(htim->Instance)); - /* Enable the Input Capture channels 1 - (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ + assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); + + /* Enable the Input Capture channel 1 + (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Hall sensor Interface. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Hall Sensor Interface handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop(TIM_HandleTypeDef* htim) { /* Check the parameters */ - assert_param(IS_TIM_XOR_INSTANCE(htim->Instance)); + assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); + /* Disable the Input Capture channels 1, 2 and 3 - (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ + (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Hall Sensor Interface in interrupt mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Hall Sensor Interface handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_IT(TIM_HandleTypeDef* htim) { + uint32_t tmpsmcr; + /* Check the parameters */ - assert_param(IS_TIM_XOR_INSTANCE(htim->Instance)); + assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); + /* Enable the capture compare Interrupts 1 event */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); - /* Enable the Input Capture channels 1 - (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ + + /* Enable the Input Capture channel 1 + (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Hall Sensor Interface in interrupt mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Hall Sensor Interface handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_IT(TIM_HandleTypeDef* htim) { /* Check the parameters */ - assert_param(IS_TIM_XOR_INSTANCE(htim->Instance)); - /* Disable the Input Capture channels 1 - (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ + assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); + + /* Disable the Input Capture channel 1 + (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); + /* Disable the capture compare Interrupts event */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Hall Sensor Interface in DMA mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param pData: The destination Buffer address. - * @param Length: The length of data to be transferred from TIM peripheral to memory. + * @param htim TIM Hall Sensor Interface handle + * @param pData The destination Buffer address. + * @param Length The length of data to be transferred from TIM peripheral to memory. * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_DMA(TIM_HandleTypeDef* htim, uint32_t* pData, uint16_t Length) { + uint32_t tmpsmcr; + /* Check the parameters */ - assert_param(IS_TIM_XOR_INSTANCE(htim->Instance)); + assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); - if ((htim->State == HAL_TIM_STATE_BUSY)) + if (htim->State == HAL_TIM_STATE_BUSY) { return HAL_BUSY; } - else if ((htim->State == HAL_TIM_STATE_READY)) + else if (htim->State == HAL_TIM_STATE_READY) { if (((uint32_t)pData == 0U) && (Length > 0U)) { @@ -370,51 +416,75 @@ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_DMA(TIM_HandleTypeDef* htim, uint32 htim->State = HAL_TIM_STATE_BUSY; } } + else + { + /* nothing to do */ + } - /* Enable the Input Capture channels 1 - (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ + /* Enable the Input Capture channel 1 + (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); - /* Set the DMA Input Capture 1 Callback */ + + /* Set the DMA Input Capture 1 Callbacks */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt; + htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMACaptureHalfCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream for Capture 1*/ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData, Length); + + /* Enable the DMA channel for Capture 1*/ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the capture compare 1 Interrupt */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Hall Sensor Interface in DMA mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @param htim TIM Hall Sensor Interface handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_DMA(TIM_HandleTypeDef* htim) { /* Check the parameters */ - assert_param(IS_TIM_XOR_INSTANCE(htim->Instance)); - /* Disable the Input Capture channels 1 - (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ + assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); + + /* Disable the Input Capture channel 1 + (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); + + /* Disable the capture compare Interrupts 1 event */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); + + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]); /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } + /** * @} */ -/** @defgroup TIMEx_Exported_Functions_Group2 Timer Complementary Output Compare functions - * @brief Timer Complementary Output Compare functions - * +/** @defgroup TIMEx_Exported_Functions_Group2 Extended Timer Complementary Output Compare functions + * @brief Timer Complementary Output Compare functions + * @verbatim ============================================================================== ##### Timer Complementary Output Compare functions ##### @@ -435,26 +505,35 @@ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_DMA(TIM_HandleTypeDef* htim) /** * @brief Starts the TIM Output Compare signal generation on the complementary * output. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be enabled. + * @param htim TIM Output Compare handle + * @param Channel TIM Channel to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_OCN_Start(TIM_HandleTypeDef* htim, uint32_t Channel) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); + /* Enable the Capture compare channel N */ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); + /* Enable the Main Output */ __HAL_TIM_MOE_ENABLE(htim); - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } @@ -462,26 +541,28 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start(TIM_HandleTypeDef* htim, uint32_t Channel) /** * @brief Stops the TIM Output Compare signal generation on the complementary * output. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be disabled. + * @param htim TIM handle + * @param Channel TIM Channel to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop(TIM_HandleTypeDef* htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); + /* Disable the Capture compare channel N */ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); + /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } @@ -489,18 +570,18 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop(TIM_HandleTypeDef* htim, uint32_t Channel) /** * @brief Starts the TIM Output Compare signal generation in interrupt mode * on the complementary output. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be enabled. + * @param htim TIM OC handle + * @param Channel TIM Channel to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); @@ -510,29 +591,23 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef* htim, uint32_t Chann { /* Enable the TIM Output Compare interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); + break; } - break; case TIM_CHANNEL_2: { /* Enable the TIM Output Compare interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); + break; } - break; case TIM_CHANNEL_3: { /* Enable the TIM Output Compare interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3); + break; } - break; - case TIM_CHANNEL_4: - { - /* Enable the TIM Output Compare interrupt */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4); - } - break; default: break; @@ -540,12 +615,21 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef* htim, uint32_t Chann /* Enable the TIM Break interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_BREAK); + /* Enable the Capture compare channel N */ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); + /* Enable the Main Output */ __HAL_TIM_MOE_ENABLE(htim); - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } @@ -553,18 +637,17 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef* htim, uint32_t Chann /** * @brief Stops the TIM Output Compare signal generation in interrupt mode * on the complementary output. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be disabled. + * @param htim TIM Output Compare handle + * @param Channel TIM Channel to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel) { + uint32_t tmpccer; /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); @@ -574,29 +657,22 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channe { /* Disable the TIM Output Compare interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); + break; } - break; case TIM_CHANNEL_2: { /* Disable the TIM Output Compare interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); + break; } - break; case TIM_CHANNEL_3: { /* Disable the TIM Output Compare interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3); + break; } - break; - - case TIM_CHANNEL_4: - { - /* Disable the TIM Output Compare interrupt */ - __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4); - } - break; default: break; @@ -606,15 +682,19 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channe TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); /* Disable the TIM Break interrupt (only if no more channel is active) */ - if ((READ_REG(htim->Instance->CCER) & (TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) == RESET) + tmpccer = htim->Instance->CCER; + + if ((tmpccer & (TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) == (uint32_t)RESET) { __HAL_TIM_DISABLE_IT(htim, TIM_IT_BREAK); } /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } @@ -622,28 +702,28 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channe /** * @brief Starts the TIM Output Compare signal generation in DMA mode * on the complementary output. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be enabled. + * @param htim TIM Output Compare handle + * @param Channel TIM Channel to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected - * @param pData: The source Buffer address. - * @param Length: The length of data to be transferred from memory to TIM peripheral + * @param pData The source Buffer address. + * @param Length The length of data to be transferred from memory to TIM peripheral * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData, uint16_t Length) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - if ((htim->State == HAL_TIM_STATE_BUSY)) + if (htim->State == HAL_TIM_STATE_BUSY) { return HAL_BUSY; } - else if ((htim->State == HAL_TIM_STATE_READY)) + else if (htim->State == HAL_TIM_STATE_READY) { if (((uint32_t)pData == 0U) && (Length > 0U)) { @@ -654,60 +734,72 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Chan htim->State = HAL_TIM_STATE_BUSY; } } + else + { + /* nothing to do */ + } switch (Channel) { case TIM_CHANNEL_1: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Output Compare DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); + break; } - break; case TIM_CHANNEL_2: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC2]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Output Compare DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); + break; } - break; case TIM_CHANNEL_3: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC3]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, Length); - /* Enable the TIM Output Compare DMA request */ - __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3); - } - break; - case TIM_CHANNEL_4: - { - /* Set the DMA Period elapsed callback */ - htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt; - /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length); + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Output Compare DMA request */ - __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4); + __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3); + break; } - break; default: break; @@ -715,10 +807,18 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Chan /* Enable the Capture compare channel N */ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); + /* Enable the Main Output */ __HAL_TIM_MOE_ENABLE(htim); - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } @@ -726,14 +826,12 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Chan /** * @brief Stops the TIM Output Compare signal generation in DMA mode * on the complementary output. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be disabled. + * @param htim TIM Output Compare handle + * @param Channel TIM Channel to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel) @@ -747,29 +845,25 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Chann { /* Disable the TIM Output Compare DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]); + break; } - break; case TIM_CHANNEL_2: { /* Disable the TIM Output Compare DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC2]); + break; } - break; case TIM_CHANNEL_3: { /* Disable the TIM Output Compare DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC3]); + break; } - break; - - case TIM_CHANNEL_4: - { - /* Disable the TIM Output Compare interrupt */ - __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4); - } - break; default: break; @@ -777,22 +871,27 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Chann /* Disable the Capture compare channel N */ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); + /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; + /* Return function status */ return HAL_OK; } + /** * @} */ -/** @defgroup TIMEx_Exported_Functions_Group3 Timer Complementary PWM functions - * @brief Timer Complementary PWM functions - * +/** @defgroup TIMEx_Exported_Functions_Group3 Extended Timer Complementary PWM functions + * @brief Timer Complementary PWM functions + * @verbatim ============================================================================== ##### Timer Complementary PWM functions ##### @@ -822,52 +921,63 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Chann /** * @brief Starts the PWM signal generation on the complementary output. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be enabled. + * @param htim TIM handle + * @param Channel TIM Channel to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start(TIM_HandleTypeDef* htim, uint32_t Channel) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); + /* Enable the complementary PWM output */ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); + /* Enable the Main Output */ __HAL_TIM_MOE_ENABLE(htim); - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } /** * @brief Stops the PWM signal generation on the complementary output. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be disabled. + * @param htim TIM handle + * @param Channel TIM Channel to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop(TIM_HandleTypeDef* htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); + /* Disable the complementary PWM output */ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); + /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } @@ -875,18 +985,18 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop(TIM_HandleTypeDef* htim, uint32_t Channel) /** * @brief Starts the PWM signal generation in interrupt mode on the * complementary output. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be disabled. + * @param htim TIM handle + * @param Channel TIM Channel to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); @@ -896,29 +1006,22 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef* htim, uint32_t Chan { /* Enable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); + break; } - break; case TIM_CHANNEL_2: { /* Enable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); + break; } - break; case TIM_CHANNEL_3: { /* Enable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3); + break; } - break; - - case TIM_CHANNEL_4: - { - /* Enable the TIM Capture/Compare 4 interrupt */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4); - } - break; default: break; @@ -926,12 +1029,21 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef* htim, uint32_t Chan /* Enable the TIM Break interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_BREAK); + /* Enable the complementary PWM output */ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); + /* Enable the Main Output */ __HAL_TIM_MOE_ENABLE(htim); - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } @@ -939,18 +1051,18 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef* htim, uint32_t Chan /** * @brief Stops the PWM signal generation in interrupt mode on the * complementary output. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be disabled. + * @param htim TIM handle + * @param Channel TIM Channel to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ -HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT (TIM_HandleTypeDef* htim, uint32_t Channel) +HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel) { + uint32_t tmpccer; + /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); @@ -960,29 +1072,22 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT (TIM_HandleTypeDef* htim, uint32_t Chan { /* Disable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); + break; } - break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); + break; } - break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3); + break; } - break; - - case TIM_CHANNEL_4: - { - /* Disable the TIM Capture/Compare 3 interrupt */ - __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4); - } - break; default: break; @@ -992,15 +1097,19 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT (TIM_HandleTypeDef* htim, uint32_t Chan TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); /* Disable the TIM Break interrupt (only if no more channel is active) */ - if ((READ_REG(htim->Instance->CCER) & (TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) == RESET) + tmpccer = htim->Instance->CCER; + + if ((tmpccer & (TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) == (uint32_t)RESET) { __HAL_TIM_DISABLE_IT(htim, TIM_IT_BREAK); } /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } @@ -1008,28 +1117,28 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT (TIM_HandleTypeDef* htim, uint32_t Chan /** * @brief Starts the TIM PWM signal generation in DMA mode on the * complementary output - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be enabled. + * @param htim TIM handle + * @param Channel TIM Channel to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected - * @param pData: The source Buffer address. - * @param Length: The length of data to be transferred from memory to TIM peripheral + * @param pData The source Buffer address. + * @param Length The length of data to be transferred from memory to TIM peripheral * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData, uint16_t Length) { + uint32_t tmpsmcr; + /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - if ((htim->State == HAL_TIM_STATE_BUSY)) + if (htim->State == HAL_TIM_STATE_BUSY) { return HAL_BUSY; } - else if ((htim->State == HAL_TIM_STATE_READY)) + else if (htim->State == HAL_TIM_STATE_READY) { if (((uint32_t)pData == 0U) && (Length > 0U)) { @@ -1040,60 +1149,72 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Cha htim->State = HAL_TIM_STATE_BUSY; } } + else + { + /* nothing to do */ + } switch (Channel) { case TIM_CHANNEL_1: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); + break; } - break; case TIM_CHANNEL_2: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC2]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); + break; } - break; case TIM_CHANNEL_3: { - /* Set the DMA Period elapsed callback */ + /* Set the DMA compare callbacks */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC3]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; + /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, Length); + + /* Enable the DMA channel */ + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, Length) != HAL_OK) + { + return HAL_ERROR; + } + /* Enable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3); + break; } - break; - - case TIM_CHANNEL_4: - { - /* Set the DMA Period elapsed callback */ - htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt; - /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; - /* Enable the DMA Stream */ - HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length); - /* Enable the TIM Capture/Compare 4 DMA request */ - __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4); - } - break; default: break; @@ -1101,10 +1222,18 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Cha /* Enable the complementary PWM output */ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); + /* Enable the Main Output */ __HAL_TIM_MOE_ENABLE(htim); - /* Enable the Peripheral */ - __HAL_TIM_ENABLE(htim); + + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + /* Return function status */ return HAL_OK; } @@ -1112,14 +1241,12 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Cha /** * @brief Stops the TIM PWM signal generation in DMA mode on the complementary * output - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Channel: TIM Channel to be disabled. + * @param htim TIM handle + * @param Channel TIM Channel to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel) @@ -1133,29 +1260,25 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Chan { /* Disable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]); + break; } - break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC2]); + break; } - break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3); + (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC3]); + break; } - break; - - case TIM_CHANNEL_4: - { - /* Disable the TIM Capture/Compare 4 DMA request */ - __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4); - } - break; default: break; @@ -1163,12 +1286,16 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Chan /* Disable the complementary PWM output */ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); + /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; + /* Return function status */ return HAL_OK; } @@ -1177,9 +1304,9 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Chan * @} */ -/** @defgroup TIMEx_Exported_Functions_Group4 Timer Complementary One Pulse functions - * @brief Timer Complementary One Pulse functions - * +/** @defgroup TIMEx_Exported_Functions_Group4 Extended Timer Complementary One Pulse functions + * @brief Timer Complementary One Pulse functions + * @verbatim ============================================================================== ##### Timer Complementary One Pulse functions ##### @@ -1198,9 +1325,8 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Chan /** * @brief Starts the TIM One Pulse signal generation on the complementary * output. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param OutputChannel: TIM Channel to be enabled. + * @param htim TIM One Pulse handle + * @param OutputChannel TIM Channel to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1210,10 +1336,13 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef* htim, uint32_t Ou { /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel)); + /* Enable the complementary One Pulse output */ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_ENABLE); + /* Enable the Main Output */ __HAL_TIM_MOE_ENABLE(htim); + /* Return function status */ return HAL_OK; } @@ -1221,9 +1350,8 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef* htim, uint32_t Ou /** * @brief Stops the TIM One Pulse signal generation on the complementary * output. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param OutputChannel: TIM Channel to be disabled. + * @param htim TIM One Pulse handle + * @param OutputChannel TIM Channel to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1231,14 +1359,19 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef* htim, uint32_t Ou */ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop(TIM_HandleTypeDef* htim, uint32_t OutputChannel) { + /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel)); + /* Disable the complementary One Pulse output */ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_DISABLE); + /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } @@ -1246,9 +1379,8 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop(TIM_HandleTypeDef* htim, uint32_t Out /** * @brief Starts the TIM One Pulse signal generation in interrupt mode on the * complementary channel. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param OutputChannel: TIM Channel to be enabled. + * @param htim TIM One Pulse handle + * @param OutputChannel TIM Channel to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1258,14 +1390,19 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start_IT(TIM_HandleTypeDef* htim, uint32_t { /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel)); + /* Enable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); + /* Enable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); + /* Enable the complementary One Pulse output */ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_ENABLE); + /* Enable the Main Output */ __HAL_TIM_MOE_ENABLE(htim); + /* Return function status */ return HAL_OK; } @@ -1273,9 +1410,8 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start_IT(TIM_HandleTypeDef* htim, uint32_t /** * @brief Stops the TIM One Pulse signal generation in interrupt mode on the * complementary channel. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param OutputChannel: TIM Channel to be disabled. + * @param htim TIM One Pulse handle + * @param OutputChannel TIM Channel to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1285,42 +1421,50 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop_IT(TIM_HandleTypeDef* htim, uint32_t { /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel)); + /* Disable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); + /* Disable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); + /* Disable the complementary One Pulse output */ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_DISABLE); + /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Return function status */ return HAL_OK; } + /** * @} */ -/** @defgroup TIMEx_Exported_Functions_Group5 Peripheral Control functions - * @brief Peripheral Control functions - * +/** @defgroup TIMEx_Exported_Functions_Group5 Extended Peripheral Control functions + * @brief Peripheral Control functions + * @verbatim ============================================================================== ##### Peripheral Control functions ##### ============================================================================== [..] This section provides functions allowing to: - (+) Configure The Input Output channels for OC, PWM, IC or One Pulse mode. - (+) Configure External Clock source. - (+) Configure Complementary channels, break features and dead time. - (+) Configure Master and the Slave synchronization. - (+) Configure the commutation event in case of use of the Hall sensor interface. - (+) Configure the DMA Burst Mode. + (+) Configure the commutation event in case of use of the Hall sensor interface. + (+) Configure Output channels for OC and PWM mode. + + (+) Configure Complementary channels, break features and dead time. + (+) Configure Master synchronization. + (+) Configure timer remapping capabilities. @endverbatim * @{ */ + /** * @brief Configure the TIM commutation event sequence. * @note This function is mandatory to use the commutation event in order to @@ -1329,26 +1473,27 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop_IT(TIM_HandleTypeDef* htim, uint32_t * configured in Hall sensor interface, this interface Timer will generate the * commutation at its TRGO output (connected to Timer used in this function) each time * the TI1 of the Interface Timer detect a commutation at its input TI1. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param InputTrigger: the Internal trigger corresponding to the Timer Interfacing with the Hall sensor. + * @param htim TIM handle + * @param InputTrigger the Internal trigger corresponding to the Timer Interfacing with the Hall sensor * This parameter can be one of the following values: * @arg TIM_TS_ITR0: Internal trigger 0 selected * @arg TIM_TS_ITR1: Internal trigger 1 selected * @arg TIM_TS_ITR2: Internal trigger 2 selected * @arg TIM_TS_ITR3: Internal trigger 3 selected * @arg TIM_TS_NONE: No trigger is needed - * @param CommutationSource: the Commutation Event source. + * @param CommutationSource the Commutation Event source * This parameter can be one of the following values: * @arg TIM_COMMUTATION_TRGI: Commutation source is the TRGI of the Interface Timer * @arg TIM_COMMUTATION_SOFTWARE: Commutation source is set by software using the COMG bit * @retval HAL status */ -HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent(TIM_HandleTypeDef* htim, uint32_t InputTrigger, uint32_t CommutationSource) +HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent(TIM_HandleTypeDef* htim, uint32_t InputTrigger, + uint32_t CommutationSource) { /* Check the parameters */ - assert_param(IS_TIM_ADVANCED_INSTANCE(htim->Instance)); + assert_param(IS_TIM_COMMUTATION_EVENT_INSTANCE(htim->Instance)); assert_param(IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(InputTrigger)); + __HAL_LOCK(htim); if ((InputTrigger == TIM_TS_ITR0) || (InputTrigger == TIM_TS_ITR1) || @@ -1364,7 +1509,15 @@ HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent(TIM_HandleTypeDef* htim, uint /* Select the Commutation event source */ htim->Instance->CR2 &= ~TIM_CR2_CCUS; htim->Instance->CR2 |= CommutationSource; + + /* Disable Commutation Interrupt */ + __HAL_TIM_DISABLE_IT(htim, TIM_IT_COM); + + /* Disable Commutation DMA request */ + __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_COM); + __HAL_UNLOCK(htim); + return HAL_OK; } @@ -1376,26 +1529,27 @@ HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent(TIM_HandleTypeDef* htim, uint * configured in Hall sensor interface, this interface Timer will generate the * commutation at its TRGO output (connected to Timer used in this function) each time * the TI1 of the Interface Timer detect a commutation at its input TI1. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param InputTrigger: the Internal trigger corresponding to the Timer Interfacing with the Hall sensor. + * @param htim TIM handle + * @param InputTrigger the Internal trigger corresponding to the Timer Interfacing with the Hall sensor * This parameter can be one of the following values: * @arg TIM_TS_ITR0: Internal trigger 0 selected * @arg TIM_TS_ITR1: Internal trigger 1 selected * @arg TIM_TS_ITR2: Internal trigger 2 selected * @arg TIM_TS_ITR3: Internal trigger 3 selected * @arg TIM_TS_NONE: No trigger is needed - * @param CommutationSource: the Commutation Event source. + * @param CommutationSource the Commutation Event source * This parameter can be one of the following values: * @arg TIM_COMMUTATION_TRGI: Commutation source is the TRGI of the Interface Timer * @arg TIM_COMMUTATION_SOFTWARE: Commutation source is set by software using the COMG bit * @retval HAL status */ -HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent_IT(TIM_HandleTypeDef* htim, uint32_t InputTrigger, uint32_t CommutationSource) +HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent_IT(TIM_HandleTypeDef* htim, uint32_t InputTrigger, + uint32_t CommutationSource) { /* Check the parameters */ - assert_param(IS_TIM_ADVANCED_INSTANCE(htim->Instance)); + assert_param(IS_TIM_COMMUTATION_EVENT_INSTANCE(htim->Instance)); assert_param(IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(InputTrigger)); + __HAL_LOCK(htim); if ((InputTrigger == TIM_TS_ITR0) || (InputTrigger == TIM_TS_ITR1) || @@ -1411,9 +1565,15 @@ HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent_IT(TIM_HandleTypeDef* htim, u /* Select the Commutation event source */ htim->Instance->CR2 &= ~TIM_CR2_CCUS; htim->Instance->CR2 |= CommutationSource; - /* Enable the Commutation Interrupt Request */ + + /* Disable Commutation DMA request */ + __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_COM); + + /* Enable the Commutation Interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_COM); + __HAL_UNLOCK(htim); + return HAL_OK; } @@ -1425,27 +1585,28 @@ HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent_IT(TIM_HandleTypeDef* htim, u * configured in Hall sensor interface, this interface Timer will generate the * commutation at its TRGO output (connected to Timer used in this function) each time * the TI1 of the Interface Timer detect a commutation at its input TI1. - * @note: The user should configure the DMA in his own software, in This function only the COMDE bit is set - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param InputTrigger: the Internal trigger corresponding to the Timer Interfacing with the Hall sensor. + * @note The user should configure the DMA in his own software, in This function only the COMDE bit is set + * @param htim TIM handle + * @param InputTrigger the Internal trigger corresponding to the Timer Interfacing with the Hall sensor * This parameter can be one of the following values: * @arg TIM_TS_ITR0: Internal trigger 0 selected * @arg TIM_TS_ITR1: Internal trigger 1 selected * @arg TIM_TS_ITR2: Internal trigger 2 selected * @arg TIM_TS_ITR3: Internal trigger 3 selected * @arg TIM_TS_NONE: No trigger is needed - * @param CommutationSource: the Commutation Event source. + * @param CommutationSource the Commutation Event source * This parameter can be one of the following values: * @arg TIM_COMMUTATION_TRGI: Commutation source is the TRGI of the Interface Timer * @arg TIM_COMMUTATION_SOFTWARE: Commutation source is set by software using the COMG bit * @retval HAL status */ -HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent_DMA(TIM_HandleTypeDef* htim, uint32_t InputTrigger, uint32_t CommutationSource) +HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent_DMA(TIM_HandleTypeDef* htim, uint32_t InputTrigger, + uint32_t CommutationSource) { /* Check the parameters */ - assert_param(IS_TIM_ADVANCED_INSTANCE(htim->Instance)); + assert_param(IS_TIM_COMMUTATION_EVENT_INSTANCE(htim->Instance)); assert_param(IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(InputTrigger)); + __HAL_LOCK(htim); if ((InputTrigger == TIM_TS_ITR0) || (InputTrigger == TIM_TS_ITR1) || @@ -1461,114 +1622,141 @@ HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent_DMA(TIM_HandleTypeDef* htim, /* Select the Commutation event source */ htim->Instance->CR2 &= ~TIM_CR2_CCUS; htim->Instance->CR2 |= CommutationSource; + /* Enable the Commutation DMA Request */ /* Set the DMA Commutation Callback */ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferCpltCallback = TIMEx_DMACommutationCplt; + htim->hdma[TIM_DMA_ID_COMMUTATION]->XferHalfCpltCallback = TIMEx_DMACommutationHalfCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferErrorCallback = TIM_DMAError; + + /* Disable Commutation Interrupt */ + __HAL_TIM_DISABLE_IT(htim, TIM_IT_COM); + /* Enable the Commutation DMA Request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_COM); + __HAL_UNLOCK(htim); + return HAL_OK; } /** * @brief Configures the TIM in master mode. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param sMasterConfig: pointer to a TIM_MasterConfigTypeDef structure that + * @param htim TIM handle. + * @param sMasterConfig pointer to a TIM_MasterConfigTypeDef structure that * contains the selected trigger output (TRGO) and the Master/Slave * mode. * @retval HAL status */ -HAL_StatusTypeDef HAL_TIMEx_MasterConfigSynchronization(TIM_HandleTypeDef* htim, TIM_MasterConfigTypeDef* sMasterConfig) +HAL_StatusTypeDef HAL_TIMEx_MasterConfigSynchronization(TIM_HandleTypeDef* htim, + TIM_MasterConfigTypeDef* sMasterConfig) { + uint32_t tmpcr2; + uint32_t tmpsmcr; + /* Check the parameters */ - assert_param(IS_TIM_MASTER_INSTANCE(htim->Instance)); + assert_param(IS_TIM_SYNCHRO_INSTANCE(htim->Instance)); assert_param(IS_TIM_TRGO_SOURCE(sMasterConfig->MasterOutputTrigger)); assert_param(IS_TIM_MSM_STATE(sMasterConfig->MasterSlaveMode)); + + /* Check input state */ __HAL_LOCK(htim); + + /* Change the handler state */ htim->State = HAL_TIM_STATE_BUSY; + + /* Get the TIMx CR2 register value */ + tmpcr2 = htim->Instance->CR2; + + /* Get the TIMx SMCR register value */ + tmpsmcr = htim->Instance->SMCR; + /* Reset the MMS Bits */ - htim->Instance->CR2 &= ~TIM_CR2_MMS; + tmpcr2 &= ~TIM_CR2_MMS; /* Select the TRGO source */ - htim->Instance->CR2 |= sMasterConfig->MasterOutputTrigger; + tmpcr2 |= sMasterConfig->MasterOutputTrigger; + /* Reset the MSM Bit */ - htim->Instance->SMCR &= ~TIM_SMCR_MSM; - /* Set or Reset the MSM Bit */ - htim->Instance->SMCR |= sMasterConfig->MasterSlaveMode; + tmpsmcr &= ~TIM_SMCR_MSM; + /* Set master mode */ + tmpsmcr |= sMasterConfig->MasterSlaveMode; + + /* Update TIMx CR2 */ + htim->Instance->CR2 = tmpcr2; + + /* Update TIMx SMCR */ + htim->Instance->SMCR = tmpsmcr; + + /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; + __HAL_UNLOCK(htim); + return HAL_OK; } /** - * @brief Configures the Break feature, dead time, Lock level, OSSI/OSSR State + * @brief Configures the Break feature, dead time, Lock level, OSSI/OSSR State * and the AOE(automatic output enable). - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param sBreakDeadTimeConfig: pointer to a TIM_ConfigBreakDeadConfig_TypeDef structure that + * @param htim TIM handle + * @param sBreakDeadTimeConfig pointer to a TIM_ConfigBreakDeadConfigTypeDef structure that * contains the BDTR Register configuration information for the TIM peripheral. + * @note Interrupts can be generated when an active level is detected on the + * break input, the break 2 input or the system break input. Break + * interrupt can be enabled by calling the @ref __HAL_TIM_ENABLE_IT macro. * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_ConfigBreakDeadTime(TIM_HandleTypeDef* htim, TIM_BreakDeadTimeConfigTypeDef* sBreakDeadTimeConfig) { + /* Keep this variable initialized to 0 as it is used to configure BDTR register */ + uint32_t tmpbdtr = 0U; + /* Check the parameters */ - assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); + assert_param(IS_TIM_BREAK_INSTANCE(htim->Instance)); assert_param(IS_TIM_OSSR_STATE(sBreakDeadTimeConfig->OffStateRunMode)); assert_param(IS_TIM_OSSI_STATE(sBreakDeadTimeConfig->OffStateIDLEMode)); assert_param(IS_TIM_LOCK_LEVEL(sBreakDeadTimeConfig->LockLevel)); + assert_param(IS_TIM_DEADTIME(sBreakDeadTimeConfig->DeadTime)); assert_param(IS_TIM_BREAK_STATE(sBreakDeadTimeConfig->BreakState)); assert_param(IS_TIM_BREAK_POLARITY(sBreakDeadTimeConfig->BreakPolarity)); assert_param(IS_TIM_AUTOMATIC_OUTPUT_STATE(sBreakDeadTimeConfig->AutomaticOutput)); - assert_param(IS_TIM_DEADTIME(sBreakDeadTimeConfig->DeadTime)); - /* Process Locked */ + + /* Check input state */ __HAL_LOCK(htim); - htim->State = HAL_TIM_STATE_BUSY; + /* Set the Lock level, the Break enable Bit and the Polarity, the OSSR State, the OSSI State, the dead time value and the Automatic Output Enable Bit */ - htim->Instance->BDTR = (uint32_t)sBreakDeadTimeConfig->OffStateRunMode | - sBreakDeadTimeConfig->OffStateIDLEMode | - sBreakDeadTimeConfig->LockLevel | - sBreakDeadTimeConfig->DeadTime | - sBreakDeadTimeConfig->BreakState | - sBreakDeadTimeConfig->BreakPolarity | - sBreakDeadTimeConfig->AutomaticOutput; - htim->State = HAL_TIM_STATE_READY; + + /* Set the BDTR bits */ + MODIFY_REG(tmpbdtr, TIM_BDTR_DTG, sBreakDeadTimeConfig->DeadTime); + MODIFY_REG(tmpbdtr, TIM_BDTR_LOCK, sBreakDeadTimeConfig->LockLevel); + MODIFY_REG(tmpbdtr, TIM_BDTR_OSSI, sBreakDeadTimeConfig->OffStateIDLEMode); + MODIFY_REG(tmpbdtr, TIM_BDTR_OSSR, sBreakDeadTimeConfig->OffStateRunMode); + MODIFY_REG(tmpbdtr, TIM_BDTR_BKE, sBreakDeadTimeConfig->BreakState); + MODIFY_REG(tmpbdtr, TIM_BDTR_BKP, sBreakDeadTimeConfig->BreakPolarity); + MODIFY_REG(tmpbdtr, TIM_BDTR_AOE, sBreakDeadTimeConfig->AutomaticOutput); + + + /* Set TIMx_BDTR */ + htim->Instance->BDTR = tmpbdtr; + __HAL_UNLOCK(htim); + return HAL_OK; } /** - * @brief Configures the TIM2, TIM5 and TIM11 Remapping input capabilities. - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. - * @param Remap: specifies the TIM input remapping source. - * This parameter can be one of the following values: - * @arg TIM_TIM2_TIM8_TRGO: TIM2 ITR1 input is connected to TIM8 Trigger output(default) - * @arg TIM_TIM2_ETH_PTP: TIM2 ITR1 input is connected to ETH PTP trigger output. - * @arg TIM_TIM2_USBFS_SOF: TIM2 ITR1 input is connected to USB FS SOF. - * @arg TIM_TIM2_USBHS_SOF: TIM2 ITR1 input is connected to USB HS SOF. - * @arg TIM_TIM5_GPIO: TIM5 CH4 input is connected to dedicated Timer pin(default) - * @arg TIM_TIM5_LSI: TIM5 CH4 input is connected to LSI clock. - * @arg TIM_TIM5_LSE: TIM5 CH4 input is connected to LSE clock. - * @arg TIM_TIM5_RTC: TIM5 CH4 input is connected to RTC Output event. - * @arg TIM_TIM11_GPIO: TIM11 CH4 input is connected to dedicated Timer pin(default) - * @arg TIM_TIM11_HSE: TIM11 CH4 input is connected to HSE_RTC clock - * (HSE divided by a programmable prescaler) + * @brief Configures the TIMx Remapping input capabilities. + * @param htim TIM handle. + * @param Remap specifies the TIM remapping source. + * * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_RemapConfig(TIM_HandleTypeDef* htim, uint32_t Remap) { - __HAL_LOCK(htim); - /* Check parameters */ - assert_param(IS_TIM_REMAP_INSTANCE(htim->Instance)); - assert_param(IS_TIM_REMAP(Remap)); - /* Set the Timer remapping configuration */ - htim->Instance->OR = Remap; - htim->State = HAL_TIM_STATE_READY; - __HAL_UNLOCK(htim); + return HAL_OK; } @@ -1576,15 +1764,15 @@ HAL_StatusTypeDef HAL_TIMEx_RemapConfig(TIM_HandleTypeDef* htim, uint32_t Remap) * @} */ -/** @defgroup TIMEx_Exported_Functions_Group6 Extension Callbacks functions - * @brief Extension Callbacks functions - * +/** @defgroup TIMEx_Exported_Functions_Group6 Extended Callbacks functions + * @brief Extended Callbacks functions + * @verbatim ============================================================================== - ##### Extension Callbacks functions ##### + ##### Extended Callbacks functions ##### ============================================================================== [..] - This section provides Extension TIM callback functions: + This section provides Extended TIM callback functions: (+) Timer Commutation callback (+) Timer Break callback @@ -1593,31 +1781,45 @@ HAL_StatusTypeDef HAL_TIMEx_RemapConfig(TIM_HandleTypeDef* htim, uint32_t Remap) */ /** - * @brief Hall commutation changed callback in non blocking mode - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @brief Hall commutation changed callback in non-blocking mode + * @param htim TIM handle * @retval None */ -__weak void HAL_TIMEx_CommutationCallback(TIM_HandleTypeDef* htim) +__weak void HAL_TIMEx_CommutCallback(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, - the HAL_TIMEx_CommutationCallback could be implemented in the user file + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_TIMEx_CommutCallback could be implemented in the user file + */ +} +/** + * @brief Hall commutation changed half complete callback in non-blocking mode + * @param htim TIM handle + * @retval None + */ +__weak void HAL_TIMEx_CommutHalfCpltCallback(TIM_HandleTypeDef* htim) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(htim); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_TIMEx_CommutHalfCpltCallback could be implemented in the user file */ } /** - * @brief Hall Break detection callback in non blocking mode - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @brief Hall Break detection callback in non-blocking mode + * @param htim TIM handle * @retval None */ __weak void HAL_TIMEx_BreakCallback(TIM_HandleTypeDef* htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); - /* NOTE : This function Should not be modified, when the callback is needed, + + /* NOTE : This function should not be modified, when the callback is needed, the HAL_TIMEx_BreakCallback could be implemented in the user file */ } @@ -1625,12 +1827,12 @@ __weak void HAL_TIMEx_BreakCallback(TIM_HandleTypeDef* htim) * @} */ -/** @defgroup TIMEx_Exported_Functions_Group7 Extension Peripheral State functions - * @brief Extension Peripheral State functions - * +/** @defgroup TIMEx_Exported_Functions_Group7 Extended Peripheral State functions + * @brief Extended Peripheral State functions + * @verbatim ============================================================================== - ##### Extension Peripheral State functions ##### + ##### Extended Peripheral State functions ##### ============================================================================== [..] This subsection permits to get in run-time the status of the peripheral @@ -1641,9 +1843,8 @@ __weak void HAL_TIMEx_BreakCallback(TIM_HandleTypeDef* htim) */ /** - * @brief Return the TIM Hall Sensor interface state - * @param htim: pointer to a TIM_HandleTypeDef structure that contains - * the configuration information for TIM module. + * @brief Return the TIM Hall Sensor interface handle state. + * @param htim TIM Hall Sensor handle * @retval HAL state */ HAL_TIM_StateTypeDef HAL_TIMEx_HallSensor_GetState(TIM_HandleTypeDef* htim) @@ -1655,47 +1856,78 @@ HAL_TIM_StateTypeDef HAL_TIMEx_HallSensor_GetState(TIM_HandleTypeDef* htim) * @} */ +/** + * @} + */ + +/* Private functions ---------------------------------------------------------*/ +/** @defgroup TIMEx_Private_Functions TIMEx Private Functions + * @{ + */ + /** * @brief TIM DMA Commutation callback. - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA module. + * @param hdma pointer to DMA handle. * @retval None */ void TIMEx_DMACommutationCplt(DMA_HandleTypeDef* hdma) { - TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + TIM_HandleTypeDef* htim = (TIM_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + + /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; - HAL_TIMEx_CommutationCallback(htim); + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->CommutationCallback(htim); +#else + HAL_TIMEx_CommutCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ } + /** - * @} + * @brief TIM DMA Commutation half complete callback. + * @param hdma pointer to DMA handle. + * @retval None */ +void TIMEx_DMACommutationHalfCplt(DMA_HandleTypeDef* hdma) +{ + TIM_HandleTypeDef* htim = (TIM_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + + /* Change the htim state */ + htim->State = HAL_TIM_STATE_READY; + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->CommutationHalfCpltCallback(htim); +#else + HAL_TIMEx_CommutHalfCpltCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ +} + /** * @brief Enables or disables the TIM Capture Compare Channel xN. * @param TIMx to select the TIM peripheral - * @param Channel: specifies the TIM Channel + * @param Channel specifies the TIM Channel * This parameter can be one of the following values: - * @arg TIM_Channel_1: TIM Channel 1 - * @arg TIM_Channel_2: TIM Channel 2 - * @arg TIM_Channel_3: TIM Channel 3 - * @param ChannelNState: specifies the TIM Channel CCxNE bit new state. + * @arg TIM_CHANNEL_1: TIM Channel 1 + * @arg TIM_CHANNEL_2: TIM Channel 2 + * @arg TIM_CHANNEL_3: TIM Channel 3 + * @param ChannelNState specifies the TIM Channel CCxNE bit new state. * This parameter can be: TIM_CCxN_ENABLE or TIM_CCxN_Disable. * @retval None */ static void TIM_CCxNChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelNState) { - uint32_t tmp = 0U; - /* Check the parameters */ - assert_param(IS_TIM_CC4_INSTANCE(TIMx)); - assert_param(IS_TIM_COMPLEMENTARY_CHANNELS(Channel)); - tmp = TIM_CCER_CC1NE << Channel; + uint32_t tmp; + + tmp = TIM_CCER_CC1NE << (Channel & 0x1FU); /* 0x1FU = 31 bits max shift */ + /* Reset the CCxNE Bit */ - TIMx->CCER &= ~tmp; + TIMx->CCER &= ~tmp; + /* Set or reset the CCxNE Bit */ - TIMx->CCER |= (uint32_t)(ChannelNState << Channel); + TIMx->CCER |= (uint32_t)(ChannelNState << (Channel & 0x1FU)); /* 0x1FU = 31 bits max shift */ } - /** * @} */ @@ -1708,4 +1940,5 @@ static void TIM_CCxNChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t Cha /** * @} */ + /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal.h b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal.h deleted file mode 100644 index f83b7325..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal.h +++ /dev/null @@ -1,265 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal.h - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief This file contains all the functions prototypes for the HAL - * module driver. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_H -#define __STM32F4xx_HAL_H - -#ifdef __cplusplus -extern "C" { -#endif - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_conf.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @addtogroup HAL - * @{ - */ - -/* Exported types ------------------------------------------------------------*/ -/* Exported constants --------------------------------------------------------*/ -/* Exported macro ------------------------------------------------------------*/ -/** @defgroup HAL_Exported_Macros HAL Exported Macros - * @{ - */ - -/** @brief Freeze/Unfreeze Peripherals in Debug mode - */ -#define __HAL_DBGMCU_FREEZE_TIM2() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_TIM2_STOP)) -#define __HAL_DBGMCU_FREEZE_TIM3() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_TIM3_STOP)) -#define __HAL_DBGMCU_FREEZE_TIM4() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_TIM4_STOP)) -#define __HAL_DBGMCU_FREEZE_TIM5() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_TIM5_STOP)) -#define __HAL_DBGMCU_FREEZE_TIM6() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_TIM6_STOP)) -#define __HAL_DBGMCU_FREEZE_TIM7() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_TIM7_STOP)) -#define __HAL_DBGMCU_FREEZE_TIM12() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_TIM12_STOP)) -#define __HAL_DBGMCU_FREEZE_TIM13() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_TIM13_STOP)) -#define __HAL_DBGMCU_FREEZE_TIM14() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_TIM14_STOP)) -#define __HAL_DBGMCU_FREEZE_RTC() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_RTC_STOP)) -#define __HAL_DBGMCU_FREEZE_WWDG() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_WWDG_STOP)) -#define __HAL_DBGMCU_FREEZE_IWDG() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_IWDG_STOP)) -#define __HAL_DBGMCU_FREEZE_I2C1_TIMEOUT() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_I2C1_SMBUS_TIMEOUT)) -#define __HAL_DBGMCU_FREEZE_I2C2_TIMEOUT() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_I2C2_SMBUS_TIMEOUT)) -#define __HAL_DBGMCU_FREEZE_I2C3_TIMEOUT() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_I2C3_SMBUS_TIMEOUT)) -#define __HAL_DBGMCU_FREEZE_CAN1() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_CAN1_STOP)) -#define __HAL_DBGMCU_FREEZE_CAN2() (DBGMCU->APB1FZ |= (DBGMCU_APB1_FZ_DBG_CAN2_STOP)) -#define __HAL_DBGMCU_FREEZE_TIM1() (DBGMCU->APB2FZ |= (DBGMCU_APB2_FZ_DBG_TIM1_STOP)) -#define __HAL_DBGMCU_FREEZE_TIM8() (DBGMCU->APB2FZ |= (DBGMCU_APB2_FZ_DBG_TIM8_STOP)) -#define __HAL_DBGMCU_FREEZE_TIM9() (DBGMCU->APB2FZ |= (DBGMCU_APB2_FZ_DBG_TIM9_STOP)) -#define __HAL_DBGMCU_FREEZE_TIM10() (DBGMCU->APB2FZ |= (DBGMCU_APB2_FZ_DBG_TIM10_STOP)) -#define __HAL_DBGMCU_FREEZE_TIM11() (DBGMCU->APB2FZ |= (DBGMCU_APB2_FZ_DBG_TIM11_STOP)) - -#define __HAL_DBGMCU_UNFREEZE_TIM2() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_TIM2_STOP)) -#define __HAL_DBGMCU_UNFREEZE_TIM3() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_TIM3_STOP)) -#define __HAL_DBGMCU_UNFREEZE_TIM4() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_TIM4_STOP)) -#define __HAL_DBGMCU_UNFREEZE_TIM5() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_TIM5_STOP)) -#define __HAL_DBGMCU_UNFREEZE_TIM6() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_TIM6_STOP)) -#define __HAL_DBGMCU_UNFREEZE_TIM7() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_TIM7_STOP)) -#define __HAL_DBGMCU_UNFREEZE_TIM12() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_TIM12_STOP)) -#define __HAL_DBGMCU_UNFREEZE_TIM13() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_TIM13_STOP)) -#define __HAL_DBGMCU_UNFREEZE_TIM14() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_TIM14_STOP)) -#define __HAL_DBGMCU_UNFREEZE_RTC() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_RTC_STOP)) -#define __HAL_DBGMCU_UNFREEZE_WWDG() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_WWDG_STOP)) -#define __HAL_DBGMCU_UNFREEZE_IWDG() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_IWDG_STOP)) -#define __HAL_DBGMCU_UNFREEZE_I2C1_TIMEOUT() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_I2C1_SMBUS_TIMEOUT)) -#define __HAL_DBGMCU_UNFREEZE_I2C2_TIMEOUT() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_I2C2_SMBUS_TIMEOUT)) -#define __HAL_DBGMCU_UNFREEZE_I2C3_TIMEOUT() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_I2C3_SMBUS_TIMEOUT)) -#define __HAL_DBGMCU_UNFREEZE_CAN1() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_CAN1_STOP)) -#define __HAL_DBGMCU_UNFREEZE_CAN2() (DBGMCU->APB1FZ &= ~(DBGMCU_APB1_FZ_DBG_CAN2_STOP)) -#define __HAL_DBGMCU_UNFREEZE_TIM1() (DBGMCU->APB2FZ &= ~(DBGMCU_APB2_FZ_DBG_TIM1_STOP)) -#define __HAL_DBGMCU_UNFREEZE_TIM8() (DBGMCU->APB2FZ &= ~(DBGMCU_APB2_FZ_DBG_TIM8_STOP)) -#define __HAL_DBGMCU_UNFREEZE_TIM9() (DBGMCU->APB2FZ &= ~(DBGMCU_APB2_FZ_DBG_TIM9_STOP)) -#define __HAL_DBGMCU_UNFREEZE_TIM10() (DBGMCU->APB2FZ &= ~(DBGMCU_APB2_FZ_DBG_TIM10_STOP)) -#define __HAL_DBGMCU_UNFREEZE_TIM11() (DBGMCU->APB2FZ &= ~(DBGMCU_APB2_FZ_DBG_TIM11_STOP)) - -/** @brief Main Flash memory mapped at 0x00000000 - */ -#define __HAL_SYSCFG_REMAPMEMORY_FLASH() (SYSCFG->MEMRMP &= ~(SYSCFG_MEMRMP_MEM_MODE)) - -/** @brief System Flash memory mapped at 0x00000000 - */ -#define __HAL_SYSCFG_REMAPMEMORY_SYSTEMFLASH() do {SYSCFG->MEMRMP &= ~(SYSCFG_MEMRMP_MEM_MODE);\ - SYSCFG->MEMRMP |= SYSCFG_MEMRMP_MEM_MODE_0;\ - }while(0); - -/** @brief Embedded SRAM mapped at 0x00000000 - */ -#define __HAL_SYSCFG_REMAPMEMORY_SRAM() do {SYSCFG->MEMRMP &= ~(SYSCFG_MEMRMP_MEM_MODE);\ - SYSCFG->MEMRMP |= (SYSCFG_MEMRMP_MEM_MODE_0 | SYSCFG_MEMRMP_MEM_MODE_1);\ - }while(0); - -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx) -/** @brief FSMC Bank1 (NOR/PSRAM 1 and 2) mapped at 0x00000000 - */ -#define __HAL_SYSCFG_REMAPMEMORY_FSMC() do {SYSCFG->MEMRMP &= ~(SYSCFG_MEMRMP_MEM_MODE);\ - SYSCFG->MEMRMP |= (SYSCFG_MEMRMP_MEM_MODE_1);\ - }while(0); -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) ||\ - defined(STM32F469xx) || defined(STM32F479xx) -/** @brief FMC Bank1 (NOR/PSRAM 1 and 2) mapped at 0x00000000 - */ -#define __HAL_SYSCFG_REMAPMEMORY_FMC() do {SYSCFG->MEMRMP &= ~(SYSCFG_MEMRMP_MEM_MODE);\ - SYSCFG->MEMRMP |= (SYSCFG_MEMRMP_MEM_MODE_1);\ - }while(0); - -/** @brief FMC/SDRAM Bank 1 and 2 mapped at 0x00000000 - */ -#define __HAL_SYSCFG_REMAPMEMORY_FMC_SDRAM() do {SYSCFG->MEMRMP &= ~(SYSCFG_MEMRMP_MEM_MODE);\ - SYSCFG->MEMRMP |= (SYSCFG_MEMRMP_MEM_MODE_2);\ - }while(0); -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -/** @defgroup Cortex_Lockup_Enable Cortex Lockup Enable - * @{ - */ -/** @brief SYSCFG Break Lockup lock - * Enables and locks the connection of Cortex-M4 LOCKUP (Hardfault) output to TIM1/8 input - * @note The selected configuration is locked and can be unlocked by system reset - */ -#define __HAL_SYSCFG_BREAK_PVD_LOCK() do {SYSCFG->CFGR2 &= ~(SYSCFG_CFGR2_PVD_LOCK); \ - SYSCFG->CFGR2 |= SYSCFG_CFGR2_PVD_LOCK; \ - }while(0) -/** - * @} - */ - -/** @defgroup PVD_Lock_Enable PVD Lock - * @{ - */ -/** @brief SYSCFG Break PVD lock - * Enables and locks the PVD connection with Timer1/8 Break Input, , as well as the PVDE and PLS[2:0] in the PWR_CR register - * @note The selected configuration is locked and can be unlocked by system reset - */ -#define __HAL_SYSCFG_BREAK_LOCKUP_LOCK() do {SYSCFG->CFGR2 &= ~(SYSCFG_CFGR2_LOCKUP_LOCK); \ - SYSCFG->CFGR2 |= SYSCFG_CFGR2_LOCKUP_LOCK; \ - }while(0) -/** - * @} - */ -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ -/** - * @} - */ - -/* Exported functions --------------------------------------------------------*/ -/** @addtogroup HAL_Exported_Functions - * @{ - */ -/** @addtogroup HAL_Exported_Functions_Group1 - * @{ - */ -/* Initialization and de-initialization functions ******************************/ -HAL_StatusTypeDef HAL_Init(void); -HAL_StatusTypeDef HAL_DeInit(void); -void HAL_MspInit(void); -void HAL_MspDeInit(void); -HAL_StatusTypeDef HAL_InitTick (uint32_t TickPriority); -/** - * @} - */ - -/** @addtogroup HAL_Exported_Functions_Group2 - * @{ - */ -/* Peripheral Control functions ************************************************/ -void HAL_IncTick(void); -void HAL_Delay(__IO uint32_t Delay); -uint32_t HAL_GetTick(void); -void HAL_SuspendTick(void); -void HAL_ResumeTick(void); -uint32_t HAL_GetHalVersion(void); -uint32_t HAL_GetREVID(void); -uint32_t HAL_GetDEVID(void); -void HAL_DBGMCU_EnableDBGSleepMode(void); -void HAL_DBGMCU_DisableDBGSleepMode(void); -void HAL_DBGMCU_EnableDBGStopMode(void); -void HAL_DBGMCU_DisableDBGStopMode(void); -void HAL_DBGMCU_EnableDBGStandbyMode(void); -void HAL_DBGMCU_DisableDBGStandbyMode(void); -void HAL_EnableCompensationCell(void); -void HAL_DisableCompensationCell(void); -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) ||\ - defined(STM32F469xx) || defined(STM32F479xx) -void HAL_EnableMemorySwappingBank(void); -void HAL_DisableMemorySwappingBank(void); -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ -/** - * @} - */ - -/** - * @} - */ -/* Private types -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/** @defgroup HAL_Private_Variables HAL Private Variables - * @{ - */ -/** - * @} - */ -/* Private constants ---------------------------------------------------------*/ -/** @defgroup HAL_Private_Constants HAL Private Constants - * @{ - */ -/** - * @} - */ -/* Private macros ------------------------------------------------------------*/ -/* Private functions ---------------------------------------------------------*/ -/** - * @} - */ - -/** - * @} - */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F4xx_HAL_H */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_can.h b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_can.h deleted file mode 100644 index 57ce1f7b..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_can.h +++ /dev/null @@ -1,779 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_can.h - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Header file of CAN HAL module. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_CAN_H -#define __STM32F4xx_HAL_CAN_H - -#ifdef __cplusplus -extern "C" { -#endif - -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) ||\ - defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) ||\ - defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_def.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @addtogroup CAN - * @{ - */ - -/* Exported types ------------------------------------------------------------*/ -/** @defgroup CAN_Exported_Types CAN Exported Types - * @{ - */ - -/** - * @brief HAL State structures definition - */ -typedef enum -{ - HAL_CAN_STATE_RESET = 0x00U, /*!< CAN not yet initialized or disabled */ - HAL_CAN_STATE_READY = 0x01U, /*!< CAN initialized and ready for use */ - HAL_CAN_STATE_BUSY = 0x02U, /*!< CAN process is ongoing */ - HAL_CAN_STATE_BUSY_TX = 0x12U, /*!< CAN process is ongoing */ - HAL_CAN_STATE_BUSY_RX = 0x22U, /*!< CAN process is ongoing */ - HAL_CAN_STATE_BUSY_TX_RX = 0x32U, /*!< CAN process is ongoing */ - HAL_CAN_STATE_TIMEOUT = 0x03U, /*!< Timeout state */ - HAL_CAN_STATE_ERROR = 0x04U /*!< CAN error state */ - -} HAL_CAN_StateTypeDef; - -/** - * @brief CAN init structure definition - */ -typedef struct -{ - uint32_t Prescaler; /*!< Specifies the length of a time quantum. - This parameter must be a number between Min_Data = 1 and Max_Data = 1024 */ - - uint32_t Mode; /*!< Specifies the CAN operating mode. - This parameter can be a value of @ref CAN_operating_mode */ - - uint32_t SJW; /*!< Specifies the maximum number of time quanta - the CAN hardware is allowed to lengthen or - shorten a bit to perform resynchronization. - This parameter can be a value of @ref CAN_synchronisation_jump_width */ - - uint32_t BS1; /*!< Specifies the number of time quanta in Bit Segment 1. - This parameter can be a value of @ref CAN_time_quantum_in_bit_segment_1 */ - - uint32_t BS2; /*!< Specifies the number of time quanta in Bit Segment 2. - This parameter can be a value of @ref CAN_time_quantum_in_bit_segment_2 */ - - uint32_t TTCM; /*!< Enable or disable the time triggered communication mode. - This parameter can be set to ENABLE or DISABLE. */ - - uint32_t ABOM; /*!< Enable or disable the automatic bus-off management. - This parameter can be set to ENABLE or DISABLE */ - - uint32_t AWUM; /*!< Enable or disable the automatic wake-up mode. - This parameter can be set to ENABLE or DISABLE */ - - uint32_t NART; /*!< Enable or disable the non-automatic retransmission mode. - This parameter can be set to ENABLE or DISABLE */ - - uint32_t RFLM; /*!< Enable or disable the receive FIFO Locked mode. - This parameter can be set to ENABLE or DISABLE */ - - uint32_t TXFP; /*!< Enable or disable the transmit FIFO priority. - This parameter can be set to ENABLE or DISABLE */ -} CAN_InitTypeDef; - -/** - * @brief CAN filter configuration structure definition - */ -typedef struct -{ - uint32_t FilterIdHigh; /*!< Specifies the filter identification number (MSBs for a 32-bit - configuration, first one for a 16-bit configuration). - This parameter must be a number between Min_Data = 0x0000U and Max_Data = 0xFFFFU */ - - uint32_t FilterIdLow; /*!< Specifies the filter identification number (LSBs for a 32-bit - configuration, second one for a 16-bit configuration). - This parameter must be a number between Min_Data = 0x0000U and Max_Data = 0xFFFFU */ - - uint32_t FilterMaskIdHigh; /*!< Specifies the filter mask number or identification number, - according to the mode (MSBs for a 32-bit configuration, - first one for a 16-bit configuration). - This parameter must be a number between Min_Data = 0x0000U and Max_Data = 0xFFFFU */ - - uint32_t FilterMaskIdLow; /*!< Specifies the filter mask number or identification number, - according to the mode (LSBs for a 32-bit configuration, - second one for a 16-bit configuration). - This parameter must be a number between Min_Data = 0x0000U and Max_Data = 0xFFFFU */ - - uint32_t FilterFIFOAssignment; /*!< Specifies the FIFO (0 or 1) which will be assigned to the filter. - This parameter can be a value of @ref CAN_filter_FIFO */ - - uint32_t FilterNumber; /*!< Specifies the filter which will be initialized. - This parameter must be a number between Min_Data = 0 and Max_Data = 27 */ - - uint32_t FilterMode; /*!< Specifies the filter mode to be initialized. - This parameter can be a value of @ref CAN_filter_mode */ - - uint32_t FilterScale; /*!< Specifies the filter scale. - This parameter can be a value of @ref CAN_filter_scale */ - - uint32_t FilterActivation; /*!< Enable or disable the filter. - This parameter can be set to ENABLE or DISABLE. */ - - uint32_t BankNumber; /*!< Select the start slave bank filter. - This parameter must be a number between Min_Data = 0 and Max_Data = 28 */ - -} CAN_FilterConfTypeDef; - -/** - * @brief CAN Tx message structure definition - */ -typedef struct -{ - uint32_t StdId; /*!< Specifies the standard identifier. - This parameter must be a number between Min_Data = 0 and Max_Data = 0x7FF */ - - uint32_t ExtId; /*!< Specifies the extended identifier. - This parameter must be a number between Min_Data = 0 and Max_Data = 0x1FFFFFFFU */ - - uint32_t IDE; /*!< Specifies the type of identifier for the message that will be transmitted. - This parameter can be a value of @ref CAN_Identifier_Type */ - - uint32_t RTR; /*!< Specifies the type of frame for the message that will be transmitted. - This parameter can be a value of @ref CAN_remote_transmission_request */ - - uint32_t DLC; /*!< Specifies the length of the frame that will be transmitted. - This parameter must be a number between Min_Data = 0 and Max_Data = 8 */ - - uint8_t Data[8]; /*!< Contains the data to be transmitted. - This parameter must be a number between Min_Data = 0 and Max_Data = 0xFF */ - -} CanTxMsgTypeDef; - -/** - * @brief CAN Rx message structure definition - */ -typedef struct -{ - uint32_t StdId; /*!< Specifies the standard identifier. - This parameter must be a number between Min_Data = 0 and Max_Data = 0x7FF */ - - uint32_t ExtId; /*!< Specifies the extended identifier. - This parameter must be a number between Min_Data = 0 and Max_Data = 0x1FFFFFFFU */ - - uint32_t IDE; /*!< Specifies the type of identifier for the message that will be received. - This parameter can be a value of @ref CAN_Identifier_Type */ - - uint32_t RTR; /*!< Specifies the type of frame for the received message. - This parameter can be a value of @ref CAN_remote_transmission_request */ - - uint32_t DLC; /*!< Specifies the length of the frame that will be received. - This parameter must be a number between Min_Data = 0 and Max_Data = 8 */ - - uint8_t Data[8]; /*!< Contains the data to be received. - This parameter must be a number between Min_Data = 0 and Max_Data = 0xFF */ - - uint32_t FMI; /*!< Specifies the index of the filter the message stored in the mailbox passes through. - This parameter must be a number between Min_Data = 0 and Max_Data = 0xFF */ - - uint32_t FIFONumber; /*!< Specifies the receive FIFO number. - This parameter can be CAN_FIFO0 or CAN_FIFO1 */ - -} CanRxMsgTypeDef; - -/** - * @brief CAN handle Structure definition - */ -typedef struct -{ - CAN_TypeDef* Instance; /*!< Register base address */ - - CAN_InitTypeDef Init; /*!< CAN required parameters */ - - CanTxMsgTypeDef* pTxMsg; /*!< Pointer to transmit structure */ - - CanRxMsgTypeDef* pRxMsg; /*!< Pointer to reception structure */ - - __IO HAL_CAN_StateTypeDef State; /*!< CAN communication state */ - - HAL_LockTypeDef Lock; /*!< CAN locking object */ - - __IO uint32_t ErrorCode; /*!< CAN Error code */ - -} CAN_HandleTypeDef; - -/** - * @} - */ - -/* Exported constants --------------------------------------------------------*/ -/** @defgroup CAN_Exported_Constants CAN Exported Constants - * @{ - */ - -/** @defgroup HAL_CAN_Error_Code HAL CAN Error Code - * @{ - */ -#define HAL_CAN_ERROR_NONE 0x00U /*!< No error */ -#define HAL_CAN_ERROR_EWG 0x01U /*!< EWG error */ -#define HAL_CAN_ERROR_EPV 0x02U /*!< EPV error */ -#define HAL_CAN_ERROR_BOF 0x04U /*!< BOF error */ -#define HAL_CAN_ERROR_STF 0x08U /*!< Stuff error */ -#define HAL_CAN_ERROR_FOR 0x10U /*!< Form error */ -#define HAL_CAN_ERROR_ACK 0x20U /*!< Acknowledgment error */ -#define HAL_CAN_ERROR_BR 0x40U /*!< Bit recessive */ -#define HAL_CAN_ERROR_BD 0x80U /*!< LEC dominant */ -#define HAL_CAN_ERROR_CRC 0x100U /*!< LEC transfer error */ -/** - * @} - */ - -/** @defgroup CAN_InitStatus CAN InitStatus - * @{ - */ -#define CAN_INITSTATUS_FAILED ((uint8_t)0x00U) /*!< CAN initialization failed */ -#define CAN_INITSTATUS_SUCCESS ((uint8_t)0x01U) /*!< CAN initialization OK */ -/** - * @} - */ - -/** @defgroup CAN_operating_mode CAN Operating Mode - * @{ - */ -#define CAN_MODE_NORMAL ((uint32_t)0x00000000U) /*!< Normal mode */ -#define CAN_MODE_LOOPBACK ((uint32_t)CAN_BTR_LBKM) /*!< Loopback mode */ -#define CAN_MODE_SILENT ((uint32_t)CAN_BTR_SILM) /*!< Silent mode */ -#define CAN_MODE_SILENT_LOOPBACK ((uint32_t)(CAN_BTR_LBKM | CAN_BTR_SILM)) /*!< Loopback combined with silent mode */ -/** - * @} - */ - -/** @defgroup CAN_synchronisation_jump_width CAN Synchronisation Jump Width - * @{ - */ -#define CAN_SJW_1TQ ((uint32_t)0x00000000U) /*!< 1 time quantum */ -#define CAN_SJW_2TQ ((uint32_t)CAN_BTR_SJW_0) /*!< 2 time quantum */ -#define CAN_SJW_3TQ ((uint32_t)CAN_BTR_SJW_1) /*!< 3 time quantum */ -#define CAN_SJW_4TQ ((uint32_t)CAN_BTR_SJW) /*!< 4 time quantum */ -/** - * @} - */ - -/** @defgroup CAN_time_quantum_in_bit_segment_1 CAN Time Quantum in bit segment 1 - * @{ - */ -#define CAN_BS1_1TQ ((uint32_t)0x00000000U) /*!< 1 time quantum */ -#define CAN_BS1_2TQ ((uint32_t)CAN_BTR_TS1_0) /*!< 2 time quantum */ -#define CAN_BS1_3TQ ((uint32_t)CAN_BTR_TS1_1) /*!< 3 time quantum */ -#define CAN_BS1_4TQ ((uint32_t)(CAN_BTR_TS1_1 | CAN_BTR_TS1_0)) /*!< 4 time quantum */ -#define CAN_BS1_5TQ ((uint32_t)CAN_BTR_TS1_2) /*!< 5 time quantum */ -#define CAN_BS1_6TQ ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_0)) /*!< 6 time quantum */ -#define CAN_BS1_7TQ ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_1)) /*!< 7 time quantum */ -#define CAN_BS1_8TQ ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_1 | CAN_BTR_TS1_0)) /*!< 8 time quantum */ -#define CAN_BS1_9TQ ((uint32_t)CAN_BTR_TS1_3) /*!< 9 time quantum */ -#define CAN_BS1_10TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_0)) /*!< 10 time quantum */ -#define CAN_BS1_11TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_1)) /*!< 11 time quantum */ -#define CAN_BS1_12TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_1 | CAN_BTR_TS1_0)) /*!< 12 time quantum */ -#define CAN_BS1_13TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2)) /*!< 13 time quantum */ -#define CAN_BS1_14TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2 | CAN_BTR_TS1_0)) /*!< 14 time quantum */ -#define CAN_BS1_15TQ ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2 | CAN_BTR_TS1_1)) /*!< 15 time quantum */ -#define CAN_BS1_16TQ ((uint32_t)CAN_BTR_TS1) /*!< 16 time quantum */ -/** - * @} - */ - -/** @defgroup CAN_time_quantum_in_bit_segment_2 CAN Time Quantum in bit segment 2 - * @{ - */ -#define CAN_BS2_1TQ ((uint32_t)0x00000000U) /*!< 1 time quantum */ -#define CAN_BS2_2TQ ((uint32_t)CAN_BTR_TS2_0) /*!< 2 time quantum */ -#define CAN_BS2_3TQ ((uint32_t)CAN_BTR_TS2_1) /*!< 3 time quantum */ -#define CAN_BS2_4TQ ((uint32_t)(CAN_BTR_TS2_1 | CAN_BTR_TS2_0)) /*!< 4 time quantum */ -#define CAN_BS2_5TQ ((uint32_t)CAN_BTR_TS2_2) /*!< 5 time quantum */ -#define CAN_BS2_6TQ ((uint32_t)(CAN_BTR_TS2_2 | CAN_BTR_TS2_0)) /*!< 6 time quantum */ -#define CAN_BS2_7TQ ((uint32_t)(CAN_BTR_TS2_2 | CAN_BTR_TS2_1)) /*!< 7 time quantum */ -#define CAN_BS2_8TQ ((uint32_t)CAN_BTR_TS2) /*!< 8 time quantum */ -/** - * @} - */ - -/** @defgroup CAN_filter_mode CAN Filter Mode - * @{ - */ -#define CAN_FILTERMODE_IDMASK ((uint8_t)0x00U) /*!< Identifier mask mode */ -#define CAN_FILTERMODE_IDLIST ((uint8_t)0x01U) /*!< Identifier list mode */ -/** - * @} - */ - -/** @defgroup CAN_filter_scale CAN Filter Scale - * @{ - */ -#define CAN_FILTERSCALE_16BIT ((uint8_t)0x00U) /*!< Two 16-bit filters */ -#define CAN_FILTERSCALE_32BIT ((uint8_t)0x01U) /*!< One 32-bit filter */ -/** - * @} - */ - -/** @defgroup CAN_filter_FIFO CAN Filter FIFO - * @{ - */ -#define CAN_FILTER_FIFO0 ((uint8_t)0x00U) /*!< Filter FIFO 0 assignment for filter x */ -#define CAN_FILTER_FIFO1 ((uint8_t)0x01U) /*!< Filter FIFO 1 assignment for filter x */ -/** - * @} - */ - -/** @defgroup CAN_Identifier_Type CAN Identifier Type - * @{ - */ -#define CAN_ID_STD ((uint32_t)0x00000000U) /*!< Standard Id */ -#define CAN_ID_EXT ((uint32_t)0x00000004U) /*!< Extended Id */ -/** - * @} - */ - -/** @defgroup CAN_remote_transmission_request CAN Remote Transmission Request - * @{ - */ -#define CAN_RTR_DATA ((uint32_t)0x00000000U) /*!< Data frame */ -#define CAN_RTR_REMOTE ((uint32_t)0x00000002U) /*!< Remote frame */ -/** - * @} - */ - -/** @defgroup CAN_receive_FIFO_number_constants CAN Receive FIFO Number Constants - * @{ - */ -#define CAN_FIFO0 ((uint8_t)0x00U) /*!< CAN FIFO 0 used to receive */ -#define CAN_FIFO1 ((uint8_t)0x01U) /*!< CAN FIFO 1 used to receive */ -/** - * @} - */ - -/** @defgroup CAN_flags CAN Flags - * @{ - */ -/* If the flag is 0x3XXXXXXX, it means that it can be used with CAN_GetFlagStatus() - and CAN_ClearFlag() functions. */ -/* If the flag is 0x1XXXXXXX, it means that it can only be used with - CAN_GetFlagStatus() function. */ - -/* Transmit Flags */ -#define CAN_FLAG_RQCP0 ((uint32_t)0x00000500U) /*!< Request MailBox0 flag */ -#define CAN_FLAG_RQCP1 ((uint32_t)0x00000508U) /*!< Request MailBox1 flag */ -#define CAN_FLAG_RQCP2 ((uint32_t)0x00000510U) /*!< Request MailBox2 flag */ -#define CAN_FLAG_TXOK0 ((uint32_t)0x00000501U) /*!< Transmission OK MailBox0 flag */ -#define CAN_FLAG_TXOK1 ((uint32_t)0x00000509U) /*!< Transmission OK MailBox1 flag */ -#define CAN_FLAG_TXOK2 ((uint32_t)0x00000511U) /*!< Transmission OK MailBox2 flag */ -#define CAN_FLAG_TME0 ((uint32_t)0x0000051AU) /*!< Transmit mailbox 0 empty flag */ -#define CAN_FLAG_TME1 ((uint32_t)0x0000051BU) /*!< Transmit mailbox 0 empty flag */ -#define CAN_FLAG_TME2 ((uint32_t)0x0000051CU) /*!< Transmit mailbox 0 empty flag */ - -/* Receive Flags */ -#define CAN_FLAG_FMP0 ((uint32_t)0x12000003) /*!< FIFO 0 Message Pending Flag */ -#define CAN_FLAG_FF0 ((uint32_t)0x00000203U) /*!< FIFO 0 Full flag */ -#define CAN_FLAG_FOV0 ((uint32_t)0x00000204U) /*!< FIFO 0 Overrun flag */ - -#define CAN_FLAG_FMP1 ((uint32_t)0x14000003) /*!< FIFO 1 Message Pending Flag */ -#define CAN_FLAG_FF1 ((uint32_t)0x00000403U) /*!< FIFO 1 Full flag */ -#define CAN_FLAG_FOV1 ((uint32_t)0x00000404U) /*!< FIFO 1 Overrun flag */ - -/* Operating Mode Flags */ -#define CAN_FLAG_INAK ((uint32_t)0x00000100U) /*!< Initialization acknowledge flag */ -#define CAN_FLAG_SLAK ((uint32_t)0x00000101U) /*!< Sleep acknowledge flag */ -#define CAN_FLAG_ERRI ((uint32_t)0x00000102U) /*!< Error flag */ -#define CAN_FLAG_WKU ((uint32_t)0x00000103U) /*!< Wake up flag */ -#define CAN_FLAG_SLAKI ((uint32_t)0x00000104U) /*!< Sleep acknowledge flag */ - -/* @note When SLAK interrupt is disabled (SLKIE=0), no polling on SLAKI is possible. - In this case the SLAK bit can be polled.*/ - -/* Error Flags */ -#define CAN_FLAG_EWG ((uint32_t)0x00000300U) /*!< Error warning flag */ -#define CAN_FLAG_EPV ((uint32_t)0x00000301U) /*!< Error passive flag */ -#define CAN_FLAG_BOF ((uint32_t)0x00000302U) /*!< Bus-Off flag */ -/** - * @} - */ - -/** @defgroup CAN_Interrupts CAN Interrupts - * @{ - */ -#define CAN_IT_TME ((uint32_t)CAN_IER_TMEIE) /*!< Transmit mailbox empty interrupt */ - -/* Receive Interrupts */ -#define CAN_IT_FMP0 ((uint32_t)CAN_IER_FMPIE0) /*!< FIFO 0 message pending interrupt */ -#define CAN_IT_FF0 ((uint32_t)CAN_IER_FFIE0) /*!< FIFO 0 full interrupt */ -#define CAN_IT_FOV0 ((uint32_t)CAN_IER_FOVIE0) /*!< FIFO 0 overrun interrupt */ -#define CAN_IT_FMP1 ((uint32_t)CAN_IER_FMPIE1) /*!< FIFO 1 message pending interrupt */ -#define CAN_IT_FF1 ((uint32_t)CAN_IER_FFIE1) /*!< FIFO 1 full interrupt */ -#define CAN_IT_FOV1 ((uint32_t)CAN_IER_FOVIE1) /*!< FIFO 1 overrun interrupt */ - -/* Operating Mode Interrupts */ -#define CAN_IT_WKU ((uint32_t)CAN_IER_WKUIE) /*!< Wake-up interrupt */ -#define CAN_IT_SLK ((uint32_t)CAN_IER_SLKIE) /*!< Sleep acknowledge interrupt */ - -/* Error Interrupts */ -#define CAN_IT_EWG ((uint32_t)CAN_IER_EWGIE) /*!< Error warning interrupt */ -#define CAN_IT_EPV ((uint32_t)CAN_IER_EPVIE) /*!< Error passive interrupt */ -#define CAN_IT_BOF ((uint32_t)CAN_IER_BOFIE) /*!< Bus-off interrupt */ -#define CAN_IT_LEC ((uint32_t)CAN_IER_LECIE) /*!< Last error code interrupt */ -#define CAN_IT_ERR ((uint32_t)CAN_IER_ERRIE) /*!< Error Interrupt */ -/** - * @} - */ - -/** @defgroup CAN_Mailboxes_Definition CAN Mailboxes Definition - * @{ - */ -#define CAN_TXMAILBOX_0 ((uint8_t)0x00U) -#define CAN_TXMAILBOX_1 ((uint8_t)0x01U) -#define CAN_TXMAILBOX_2 ((uint8_t)0x02U) -/** - * @} - */ - -/** - * @} - */ - -/* Exported macro ------------------------------------------------------------*/ -/** @defgroup CAN_Exported_Macros CAN Exported Macros - * @{ - */ - -/** @brief Reset CAN handle state - * @param __HANDLE__: specifies the CAN Handle. - * @retval None - */ -#define __HAL_CAN_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_CAN_STATE_RESET) - -/** - * @brief Enable the specified CAN interrupts. - * @param __HANDLE__: CAN handle - * @param __INTERRUPT__: CAN Interrupt - * @retval None - */ -#define __HAL_CAN_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->IER) |= (__INTERRUPT__)) - -/** - * @brief Disable the specified CAN interrupts. - * @param __HANDLE__: CAN handle - * @param __INTERRUPT__: CAN Interrupt - * @retval None - */ -#define __HAL_CAN_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->IER) &= ~(__INTERRUPT__)) - -/** - * @brief Return the number of pending received messages. - * @param __HANDLE__: CAN handle - * @param __FIFONUMBER__: Receive FIFO number, CAN_FIFO0 or CAN_FIFO1. - * @retval The number of pending message. - */ -#define __HAL_CAN_MSG_PENDING(__HANDLE__, __FIFONUMBER__) (((__FIFONUMBER__) == CAN_FIFO0)? \ -((uint8_t)((__HANDLE__)->Instance->RF0R&(uint32_t)0x03U)) : ((uint8_t)((__HANDLE__)->Instance->RF1R & (uint32_t)0x03U))) - -/** @brief Check whether the specified CAN flag is set or not. - * @param __HANDLE__: CAN Handle - * @param __FLAG__: specifies the flag to check. - * This parameter can be one of the following values: - * @arg CAN_TSR_RQCP0: Request MailBox0 Flag - * @arg CAN_TSR_RQCP1: Request MailBox1 Flag - * @arg CAN_TSR_RQCP2: Request MailBox2 Flag - * @arg CAN_FLAG_TXOK0: Transmission OK MailBox0 Flag - * @arg CAN_FLAG_TXOK1: Transmission OK MailBox1 Flag - * @arg CAN_FLAG_TXOK2: Transmission OK MailBox2 Flag - * @arg CAN_FLAG_TME0: Transmit mailbox 0 empty Flag - * @arg CAN_FLAG_TME1: Transmit mailbox 1 empty Flag - * @arg CAN_FLAG_TME2: Transmit mailbox 2 empty Flag - * @arg CAN_FLAG_FMP0: FIFO 0 Message Pending Flag - * @arg CAN_FLAG_FF0: FIFO 0 Full Flag - * @arg CAN_FLAG_FOV0: FIFO 0 Overrun Flag - * @arg CAN_FLAG_FMP1: FIFO 1 Message Pending Flag - * @arg CAN_FLAG_FF1: FIFO 1 Full Flag - * @arg CAN_FLAG_FOV1: FIFO 1 Overrun Flag - * @arg CAN_FLAG_WKU: Wake up Flag - * @arg CAN_FLAG_SLAK: Sleep acknowledge Flag - * @arg CAN_FLAG_SLAKI: Sleep acknowledge Flag - * @arg CAN_FLAG_EWG: Error Warning Flag - * @arg CAN_FLAG_EPV: Error Passive Flag - * @arg CAN_FLAG_BOF: Bus-Off Flag - * @retval The new state of __FLAG__ (TRUE or FALSE). - */ -#define __HAL_CAN_GET_FLAG(__HANDLE__, __FLAG__) \ -((((__FLAG__) >> 8U) == 5U)? ((((__HANDLE__)->Instance->TSR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ - (((__FLAG__) >> 8U) == 2U)? ((((__HANDLE__)->Instance->RF0R) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ - (((__FLAG__) >> 8U) == 4U)? ((((__HANDLE__)->Instance->RF1R) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ - (((__FLAG__) >> 8U) == 1U)? ((((__HANDLE__)->Instance->MSR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \ - ((((__HANDLE__)->Instance->ESR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK)))) - -/** @brief Clear the specified CAN pending flag. - * @param __HANDLE__: CAN Handle. - * @param __FLAG__: specifies the flag to check. - * This parameter can be one of the following values: - * @arg CAN_TSR_RQCP0: Request MailBox0 Flag - * @arg CAN_TSR_RQCP1: Request MailBox1 Flag - * @arg CAN_TSR_RQCP2: Request MailBox2 Flag - * @arg CAN_FLAG_TXOK0: Transmission OK MailBox0 Flag - * @arg CAN_FLAG_TXOK1: Transmission OK MailBox1 Flag - * @arg CAN_FLAG_TXOK2: Transmission OK MailBox2 Flag - * @arg CAN_FLAG_TME0: Transmit mailbox 0 empty Flag - * @arg CAN_FLAG_TME1: Transmit mailbox 1 empty Flag - * @arg CAN_FLAG_TME2: Transmit mailbox 2 empty Flag - * @arg CAN_FLAG_FMP0: FIFO 0 Message Pending Flag - * @arg CAN_FLAG_FF0: FIFO 0 Full Flag - * @arg CAN_FLAG_FOV0: FIFO 0 Overrun Flag - * @arg CAN_FLAG_FMP1: FIFO 1 Message Pending Flag - * @arg CAN_FLAG_FF1: FIFO 1 Full Flag - * @arg CAN_FLAG_FOV1: FIFO 1 Overrun Flag - * @arg CAN_FLAG_WKU: Wake up Flag - * @arg CAN_FLAG_SLAK: Sleep acknowledge Flag - * @arg CAN_FLAG_SLAKI: Sleep acknowledge Flag - * @retval The new state of __FLAG__ (TRUE or FALSE). - */ -#define __HAL_CAN_CLEAR_FLAG(__HANDLE__, __FLAG__) \ -((((__FLAG__) >> 8U) == 5U)? (((__HANDLE__)->Instance->TSR) = ((uint32_t)1U << ((__FLAG__) & CAN_FLAG_MASK))): \ - (((__FLAG__) >> 8U) == 2U)? (((__HANDLE__)->Instance->RF0R) = ((uint32_t)1U << ((__FLAG__) & CAN_FLAG_MASK))): \ - (((__FLAG__) >> 8U) == 4U)? (((__HANDLE__)->Instance->RF1R) = ((uint32_t)1U << ((__FLAG__) & CAN_FLAG_MASK))): \ - (((__HANDLE__)->Instance->MSR) = ((uint32_t)1U << ((__FLAG__) & CAN_FLAG_MASK)))) - -/** @brief Check if the specified CAN interrupt source is enabled or disabled. - * @param __HANDLE__: CAN Handle - * @param __INTERRUPT__: specifies the CAN interrupt source to check. - * This parameter can be one of the following values: - * @arg CAN_IT_TME: Transmit mailbox empty interrupt enable - * @arg CAN_IT_FMP0: FIFO0 message pending interrupt enable - * @arg CAN_IT_FMP1: FIFO1 message pending interrupt enable - * @retval The new state of __IT__ (TRUE or FALSE). - */ -#define __HAL_CAN_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->IER & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET) - -/** - * @brief Check the transmission status of a CAN Frame. - * @param __HANDLE__: CAN Handle - * @param __TRANSMITMAILBOX__: the number of the mailbox that is used for transmission. - * @retval The new status of transmission (TRUE or FALSE). - */ -#define __HAL_CAN_TRANSMIT_STATUS(__HANDLE__, __TRANSMITMAILBOX__)\ -(((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_0)? ((((__HANDLE__)->Instance->TSR) & (CAN_TSR_RQCP0 | CAN_TSR_TXOK0 | CAN_TSR_TME0)) == (CAN_TSR_RQCP0 | CAN_TSR_TXOK0 | CAN_TSR_TME0)) :\ - ((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_1)? ((((__HANDLE__)->Instance->TSR) & (CAN_TSR_RQCP1 | CAN_TSR_TXOK1 | CAN_TSR_TME1)) == (CAN_TSR_RQCP1 | CAN_TSR_TXOK1 | CAN_TSR_TME1)) :\ - ((((__HANDLE__)->Instance->TSR) & (CAN_TSR_RQCP2 | CAN_TSR_TXOK2 | CAN_TSR_TME2)) == (CAN_TSR_RQCP2 | CAN_TSR_TXOK2 | CAN_TSR_TME2))) - -/** - * @brief Release the specified receive FIFO. - * @param __HANDLE__: CAN handle - * @param __FIFONUMBER__: Receive FIFO number, CAN_FIFO0 or CAN_FIFO1. - * @retval None - */ -#define __HAL_CAN_FIFO_RELEASE(__HANDLE__, __FIFONUMBER__) (((__FIFONUMBER__) == CAN_FIFO0)? \ -((__HANDLE__)->Instance->RF0R = CAN_RF0R_RFOM0) : ((__HANDLE__)->Instance->RF1R = CAN_RF1R_RFOM1)) - -/** - * @brief Cancel a transmit request. - * @param __HANDLE__: CAN Handle - * @param __TRANSMITMAILBOX__: the number of the mailbox that is used for transmission. - * @retval None - */ -#define __HAL_CAN_CANCEL_TRANSMIT(__HANDLE__, __TRANSMITMAILBOX__)\ -(((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_0)? ((__HANDLE__)->Instance->TSR = CAN_TSR_ABRQ0) :\ - ((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_1)? ((__HANDLE__)->Instance->TSR = CAN_TSR_ABRQ1) :\ - ((__HANDLE__)->Instance->TSR = CAN_TSR_ABRQ2)) - -/** - * @brief Enable or disable the DBG Freeze for CAN. - * @param __HANDLE__: CAN Handle - * @param __NEWSTATE__: new state of the CAN peripheral. - * This parameter can be: ENABLE (CAN reception/transmission is frozen - * during debug. Reception FIFOs can still be accessed/controlled normally) - * or DISABLE (CAN is working during debug). - * @retval None - */ -#define __HAL_CAN_DBG_FREEZE(__HANDLE__, __NEWSTATE__) (((__NEWSTATE__) == ENABLE)? \ -((__HANDLE__)->Instance->MCR |= CAN_MCR_DBF) : ((__HANDLE__)->Instance->MCR &= ~CAN_MCR_DBF)) - -/** - * @} - */ - -/* Exported functions --------------------------------------------------------*/ -/** @addtogroup CAN_Exported_Functions - * @{ - */ - -/** @addtogroup CAN_Exported_Functions_Group1 - * @{ - */ -/* Initialization/de-initialization functions ***********************************/ -HAL_StatusTypeDef HAL_CAN_Init(CAN_HandleTypeDef* hcan); -HAL_StatusTypeDef HAL_CAN_ConfigFilter(CAN_HandleTypeDef* hcan, CAN_FilterConfTypeDef* sFilterConfig); -HAL_StatusTypeDef HAL_CAN_DeInit(CAN_HandleTypeDef* hcan); -void HAL_CAN_MspInit(CAN_HandleTypeDef* hcan); -void HAL_CAN_MspDeInit(CAN_HandleTypeDef* hcan); -/** - * @} - */ - -/** @addtogroup CAN_Exported_Functions_Group2 - * @{ - */ -/* I/O operation functions ******************************************************/ -HAL_StatusTypeDef HAL_CAN_Transmit(CAN_HandleTypeDef* hcan, uint32_t Timeout); -HAL_StatusTypeDef HAL_CAN_Transmit_IT(CAN_HandleTypeDef* hcan); -HAL_StatusTypeDef HAL_CAN_Receive(CAN_HandleTypeDef* hcan, uint8_t FIFONumber, uint32_t Timeout); -HAL_StatusTypeDef HAL_CAN_Receive_IT(CAN_HandleTypeDef* hcan, uint8_t FIFONumber); -HAL_StatusTypeDef HAL_CAN_Sleep(CAN_HandleTypeDef* hcan); -HAL_StatusTypeDef HAL_CAN_WakeUp(CAN_HandleTypeDef* hcan); -void HAL_CAN_IRQHandler(CAN_HandleTypeDef* hcan); -void HAL_CAN_TxCpltCallback(CAN_HandleTypeDef* hcan); -void HAL_CAN_RxCpltCallback(CAN_HandleTypeDef* hcan); -void HAL_CAN_ErrorCallback(CAN_HandleTypeDef* hcan); -/** - * @} - */ - -/** @addtogroup CAN_Exported_Functions_Group3 - * @{ - */ -/* Peripheral State functions ***************************************************/ -uint32_t HAL_CAN_GetError(CAN_HandleTypeDef* hcan); -HAL_CAN_StateTypeDef HAL_CAN_GetState(CAN_HandleTypeDef* hcan); -/** - * @} - */ - -/** - * @} - */ - -/* Private types -------------------------------------------------------------*/ -/** @defgroup CAN_Private_Types CAN Private Types - * @{ - */ - -/** - * @} - */ - -/* Private variables ---------------------------------------------------------*/ -/** @defgroup CAN_Private_Variables CAN Private Variables - * @{ - */ - -/** - * @} - */ - -/* Private constants ---------------------------------------------------------*/ -/** @defgroup CAN_Private_Constants CAN Private Constants - * @{ - */ -#define CAN_TXSTATUS_NOMAILBOX ((uint8_t)0x04U) /*!< CAN cell did not provide CAN_TxStatus_NoMailBox */ -#define CAN_FLAG_MASK ((uint32_t)0x000000FFU) -/** - * @} - */ - -/* Private macros ------------------------------------------------------------*/ -/** @defgroup CAN_Private_Macros CAN Private Macros - * @{ - */ -#define IS_CAN_MODE(MODE) (((MODE) == CAN_MODE_NORMAL) || \ - ((MODE) == CAN_MODE_LOOPBACK)|| \ - ((MODE) == CAN_MODE_SILENT) || \ - ((MODE) == CAN_MODE_SILENT_LOOPBACK)) -#define IS_CAN_SJW(SJW) (((SJW) == CAN_SJW_1TQ) || ((SJW) == CAN_SJW_2TQ)|| \ - ((SJW) == CAN_SJW_3TQ) || ((SJW) == CAN_SJW_4TQ)) -#define IS_CAN_BS1(BS1) ((BS1) <= CAN_BS1_16TQ) -#define IS_CAN_BS2(BS2) ((BS2) <= CAN_BS2_8TQ) -#define IS_CAN_PRESCALER(PRESCALER) (((PRESCALER) >= 1U) && ((PRESCALER) <= 1024U)) -#define IS_CAN_FILTER_NUMBER(NUMBER) ((NUMBER) <= 27U) -#define IS_CAN_FILTER_MODE(MODE) (((MODE) == CAN_FILTERMODE_IDMASK) || \ - ((MODE) == CAN_FILTERMODE_IDLIST)) -#define IS_CAN_FILTER_SCALE(SCALE) (((SCALE) == CAN_FILTERSCALE_16BIT) || \ - ((SCALE) == CAN_FILTERSCALE_32BIT)) -#define IS_CAN_FILTER_FIFO(FIFO) (((FIFO) == CAN_FILTER_FIFO0) || \ - ((FIFO) == CAN_FILTER_FIFO1)) -#define IS_CAN_BANKNUMBER(BANKNUMBER) ((BANKNUMBER) <= 28U) - -#define IS_CAN_TRANSMITMAILBOX(TRANSMITMAILBOX) ((TRANSMITMAILBOX) <= ((uint8_t)0x02U)) -#define IS_CAN_STDID(STDID) ((STDID) <= ((uint32_t)0x7FFU)) -#define IS_CAN_EXTID(EXTID) ((EXTID) <= ((uint32_t)0x1FFFFFFFU)) -#define IS_CAN_DLC(DLC) ((DLC) <= ((uint8_t)0x08U)) - -#define IS_CAN_IDTYPE(IDTYPE) (((IDTYPE) == CAN_ID_STD) || \ - ((IDTYPE) == CAN_ID_EXT)) -#define IS_CAN_RTR(RTR) (((RTR) == CAN_RTR_DATA) || ((RTR) == CAN_RTR_REMOTE)) -#define IS_CAN_FIFO(FIFO) (((FIFO) == CAN_FIFO0) || ((FIFO) == CAN_FIFO1)) - -/** - * @} - */ - -/* Private functions ---------------------------------------------------------*/ -/** @defgroup CAN_Private_Functions CAN Private Functions - * @{ - */ - -/** - * @} - */ - -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\ - STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx ||\ - STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -/** - * @} - */ - -/** - * @} - */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F4xx_CAN_H */ - - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_dma.h b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_dma.h deleted file mode 100644 index a8fbfdba..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_dma.h +++ /dev/null @@ -1,793 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_dma.h - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Header file of DMA HAL module. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_DMA_H -#define __STM32F4xx_HAL_DMA_H - -#ifdef __cplusplus -extern "C" { -#endif - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_def.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @addtogroup DMA - * @{ - */ - -/* Exported types ------------------------------------------------------------*/ - -/** @defgroup DMA_Exported_Types DMA Exported Types - * @brief DMA Exported Types - * @{ - */ - -/** - * @brief DMA Configuration Structure definition - */ -typedef struct -{ - uint32_t Channel; /*!< Specifies the channel used for the specified stream. - This parameter can be a value of @ref DMA_Channel_selection */ - - uint32_t Direction; /*!< Specifies if the data will be transferred from memory to peripheral, - from memory to memory or from peripheral to memory. - This parameter can be a value of @ref DMA_Data_transfer_direction */ - - uint32_t PeriphInc; /*!< Specifies whether the Peripheral address register should be incremented or not. - This parameter can be a value of @ref DMA_Peripheral_incremented_mode */ - - uint32_t MemInc; /*!< Specifies whether the memory address register should be incremented or not. - This parameter can be a value of @ref DMA_Memory_incremented_mode */ - - uint32_t PeriphDataAlignment; /*!< Specifies the Peripheral data width. - This parameter can be a value of @ref DMA_Peripheral_data_size */ - - uint32_t MemDataAlignment; /*!< Specifies the Memory data width. - This parameter can be a value of @ref DMA_Memory_data_size */ - - uint32_t Mode; /*!< Specifies the operation mode of the DMAy Streamx. - This parameter can be a value of @ref DMA_mode - @note The circular buffer mode cannot be used if the memory-to-memory - data transfer is configured on the selected Stream */ - - uint32_t Priority; /*!< Specifies the software priority for the DMAy Streamx. - This parameter can be a value of @ref DMA_Priority_level */ - - uint32_t FIFOMode; /*!< Specifies if the FIFO mode or Direct mode will be used for the specified stream. - This parameter can be a value of @ref DMA_FIFO_direct_mode - @note The Direct mode (FIFO mode disabled) cannot be used if the - memory-to-memory data transfer is configured on the selected stream */ - - uint32_t FIFOThreshold; /*!< Specifies the FIFO threshold level. - This parameter can be a value of @ref DMA_FIFO_threshold_level */ - - uint32_t MemBurst; /*!< Specifies the Burst transfer configuration for the memory transfers. - It specifies the amount of data to be transferred in a single non interruptible - transaction. - This parameter can be a value of @ref DMA_Memory_burst - @note The burst mode is possible only if the address Increment mode is enabled. */ - - uint32_t PeriphBurst; /*!< Specifies the Burst transfer configuration for the peripheral transfers. - It specifies the amount of data to be transferred in a single non interruptible - transaction. - This parameter can be a value of @ref DMA_Peripheral_burst - @note The burst mode is possible only if the address Increment mode is enabled. */ -} DMA_InitTypeDef; - - -/** - * @brief HAL DMA State structures definition - */ -typedef enum -{ - HAL_DMA_STATE_RESET = 0x00U, /*!< DMA not yet initialized or disabled */ - HAL_DMA_STATE_READY = 0x01U, /*!< DMA initialized and ready for use */ - HAL_DMA_STATE_BUSY = 0x02U, /*!< DMA process is ongoing */ - HAL_DMA_STATE_TIMEOUT = 0x03U, /*!< DMA timeout state */ - HAL_DMA_STATE_ERROR = 0x04U, /*!< DMA error state */ - HAL_DMA_STATE_ABORT = 0x05U, /*!< DMA Abort state */ -} HAL_DMA_StateTypeDef; - -/** - * @brief HAL DMA Error Code structure definition - */ -typedef enum -{ - HAL_DMA_FULL_TRANSFER = 0x00U, /*!< Full transfer */ - HAL_DMA_HALF_TRANSFER = 0x01U /*!< Half Transfer */ -} HAL_DMA_LevelCompleteTypeDef; - -/** - * @brief HAL DMA Error Code structure definition - */ -typedef enum -{ - HAL_DMA_XFER_CPLT_CB_ID = 0x00U, /*!< Full transfer */ - HAL_DMA_XFER_HALFCPLT_CB_ID = 0x01U, /*!< Half Transfer */ - HAL_DMA_XFER_M1CPLT_CB_ID = 0x02U, /*!< M1 Full Transfer */ - HAL_DMA_XFER_M1HALFCPLT_CB_ID = 0x03U, /*!< M1 Half Transfer */ - HAL_DMA_XFER_ERROR_CB_ID = 0x04U, /*!< Error */ - HAL_DMA_XFER_ABORT_CB_ID = 0x05U, /*!< Abort */ - HAL_DMA_XFER_ALL_CB_ID = 0x06U /*!< All */ -} HAL_DMA_CallbackIDTypeDef; - -/** - * @brief DMA handle Structure definition - */ -typedef struct __DMA_HandleTypeDef -{ - DMA_Stream_TypeDef* Instance; /*!< Register base address */ - - DMA_InitTypeDef Init; /*!< DMA communication parameters */ - - HAL_LockTypeDef Lock; /*!< DMA locking object */ - - __IO HAL_DMA_StateTypeDef State; /*!< DMA transfer state */ - - void* Parent; /*!< Parent object state */ - - void (* XferCpltCallback)( struct __DMA_HandleTypeDef* hdma); /*!< DMA transfer complete callback */ - - void (* XferHalfCpltCallback)( struct __DMA_HandleTypeDef* hdma); /*!< DMA Half transfer complete callback */ - - void (* XferM1CpltCallback)( struct __DMA_HandleTypeDef* hdma); /*!< DMA transfer complete Memory1 callback */ - - void (* XferM1HalfCpltCallback)( struct __DMA_HandleTypeDef* hdma); /*!< DMA transfer Half complete Memory1 callback */ - - void (* XferErrorCallback)( struct __DMA_HandleTypeDef* hdma); /*!< DMA transfer error callback */ - - void (* XferAbortCallback)( struct __DMA_HandleTypeDef* hdma); /*!< DMA transfer Abort callback */ - - __IO uint32_t ErrorCode; /*!< DMA Error code */ - - uint32_t StreamBaseAddress; /*!< DMA Stream Base Address */ - - uint32_t StreamIndex; /*!< DMA Stream Index */ - -} DMA_HandleTypeDef; - -/** - * @} - */ - -/* Exported constants --------------------------------------------------------*/ - -/** @defgroup DMA_Exported_Constants DMA Exported Constants - * @brief DMA Exported constants - * @{ - */ - -/** @defgroup DMA_Error_Code DMA Error Code - * @brief DMA Error Code - * @{ - */ -#define HAL_DMA_ERROR_NONE ((uint32_t)0x00000000U) /*!< No error */ -#define HAL_DMA_ERROR_TE ((uint32_t)0x00000001U) /*!< Transfer error */ -#define HAL_DMA_ERROR_FE ((uint32_t)0x00000002U) /*!< FIFO error */ -#define HAL_DMA_ERROR_DME ((uint32_t)0x00000004U) /*!< Direct Mode error */ -#define HAL_DMA_ERROR_TIMEOUT ((uint32_t)0x00000020U) /*!< Timeout error */ -#define HAL_DMA_ERROR_PARAM ((uint32_t)0x00000040U) /*!< Parameter error */ -#define HAL_DMA_ERROR_NO_XFER ((uint32_t)0x00000080U) /*!< Abort requested with no Xfer ongoing */ -#define HAL_DMA_ERROR_NOT_SUPPORTED ((uint32_t)0x00000100U) /*!< Not supported mode */ -/** - * @} - */ - -/** @defgroup DMA_Channel_selection DMA Channel selection - * @brief DMA channel selection - * @{ - */ -#define DMA_CHANNEL_0 ((uint32_t)0x00000000U) /*!< DMA Channel 0 */ -#define DMA_CHANNEL_1 ((uint32_t)0x02000000U) /*!< DMA Channel 1 */ -#define DMA_CHANNEL_2 ((uint32_t)0x04000000U) /*!< DMA Channel 2 */ -#define DMA_CHANNEL_3 ((uint32_t)0x06000000U) /*!< DMA Channel 3 */ -#define DMA_CHANNEL_4 ((uint32_t)0x08000000U) /*!< DMA Channel 4 */ -#define DMA_CHANNEL_5 ((uint32_t)0x0A000000U) /*!< DMA Channel 5 */ -#define DMA_CHANNEL_6 ((uint32_t)0x0C000000U) /*!< DMA Channel 6 */ -#define DMA_CHANNEL_7 ((uint32_t)0x0E000000U) /*!< DMA Channel 7 */ -/** - * @} - */ - -/** @defgroup DMA_Data_transfer_direction DMA Data transfer direction - * @brief DMA data transfer direction - * @{ - */ -#define DMA_PERIPH_TO_MEMORY ((uint32_t)0x00000000U) /*!< Peripheral to memory direction */ -#define DMA_MEMORY_TO_PERIPH ((uint32_t)DMA_SxCR_DIR_0) /*!< Memory to peripheral direction */ -#define DMA_MEMORY_TO_MEMORY ((uint32_t)DMA_SxCR_DIR_1) /*!< Memory to memory direction */ -/** - * @} - */ - -/** @defgroup DMA_Peripheral_incremented_mode DMA Peripheral incremented mode - * @brief DMA peripheral incremented mode - * @{ - */ -#define DMA_PINC_ENABLE ((uint32_t)DMA_SxCR_PINC) /*!< Peripheral increment mode enable */ -#define DMA_PINC_DISABLE ((uint32_t)0x00000000U) /*!< Peripheral increment mode disable */ -/** - * @} - */ - -/** @defgroup DMA_Memory_incremented_mode DMA Memory incremented mode - * @brief DMA memory incremented mode - * @{ - */ -#define DMA_MINC_ENABLE ((uint32_t)DMA_SxCR_MINC) /*!< Memory increment mode enable */ -#define DMA_MINC_DISABLE ((uint32_t)0x00000000U) /*!< Memory increment mode disable */ -/** - * @} - */ - -/** @defgroup DMA_Peripheral_data_size DMA Peripheral data size - * @brief DMA peripheral data size - * @{ - */ -#define DMA_PDATAALIGN_BYTE ((uint32_t)0x00000000U) /*!< Peripheral data alignment: Byte */ -#define DMA_PDATAALIGN_HALFWORD ((uint32_t)DMA_SxCR_PSIZE_0) /*!< Peripheral data alignment: HalfWord */ -#define DMA_PDATAALIGN_WORD ((uint32_t)DMA_SxCR_PSIZE_1) /*!< Peripheral data alignment: Word */ -/** - * @} - */ - -/** @defgroup DMA_Memory_data_size DMA Memory data size - * @brief DMA memory data size - * @{ - */ -#define DMA_MDATAALIGN_BYTE ((uint32_t)0x00000000U) /*!< Memory data alignment: Byte */ -#define DMA_MDATAALIGN_HALFWORD ((uint32_t)DMA_SxCR_MSIZE_0) /*!< Memory data alignment: HalfWord */ -#define DMA_MDATAALIGN_WORD ((uint32_t)DMA_SxCR_MSIZE_1) /*!< Memory data alignment: Word */ -/** - * @} - */ - -/** @defgroup DMA_mode DMA mode - * @brief DMA mode - * @{ - */ -#define DMA_NORMAL ((uint32_t)0x00000000U) /*!< Normal mode */ -#define DMA_CIRCULAR ((uint32_t)DMA_SxCR_CIRC) /*!< Circular mode */ -#define DMA_PFCTRL ((uint32_t)DMA_SxCR_PFCTRL) /*!< Peripheral flow control mode */ -/** - * @} - */ - -/** @defgroup DMA_Priority_level DMA Priority level - * @brief DMA priority levels - * @{ - */ -#define DMA_PRIORITY_LOW ((uint32_t)0x00000000U) /*!< Priority level: Low */ -#define DMA_PRIORITY_MEDIUM ((uint32_t)DMA_SxCR_PL_0) /*!< Priority level: Medium */ -#define DMA_PRIORITY_HIGH ((uint32_t)DMA_SxCR_PL_1) /*!< Priority level: High */ -#define DMA_PRIORITY_VERY_HIGH ((uint32_t)DMA_SxCR_PL) /*!< Priority level: Very High */ -/** - * @} - */ - -/** @defgroup DMA_FIFO_direct_mode DMA FIFO direct mode - * @brief DMA FIFO direct mode - * @{ - */ -#define DMA_FIFOMODE_DISABLE ((uint32_t)0x00000000U) /*!< FIFO mode disable */ -#define DMA_FIFOMODE_ENABLE ((uint32_t)DMA_SxFCR_DMDIS) /*!< FIFO mode enable */ -/** - * @} - */ - -/** @defgroup DMA_FIFO_threshold_level DMA FIFO threshold level - * @brief DMA FIFO level - * @{ - */ -#define DMA_FIFO_THRESHOLD_1QUARTERFULL ((uint32_t)0x00000000U) /*!< FIFO threshold 1 quart full configuration */ -#define DMA_FIFO_THRESHOLD_HALFFULL ((uint32_t)DMA_SxFCR_FTH_0) /*!< FIFO threshold half full configuration */ -#define DMA_FIFO_THRESHOLD_3QUARTERSFULL ((uint32_t)DMA_SxFCR_FTH_1) /*!< FIFO threshold 3 quarts full configuration */ -#define DMA_FIFO_THRESHOLD_FULL ((uint32_t)DMA_SxFCR_FTH) /*!< FIFO threshold full configuration */ -/** - * @} - */ - -/** @defgroup DMA_Memory_burst DMA Memory burst - * @brief DMA memory burst - * @{ - */ -#define DMA_MBURST_SINGLE ((uint32_t)0x00000000U) -#define DMA_MBURST_INC4 ((uint32_t)DMA_SxCR_MBURST_0) -#define DMA_MBURST_INC8 ((uint32_t)DMA_SxCR_MBURST_1) -#define DMA_MBURST_INC16 ((uint32_t)DMA_SxCR_MBURST) -/** - * @} - */ - -/** @defgroup DMA_Peripheral_burst DMA Peripheral burst - * @brief DMA peripheral burst - * @{ - */ -#define DMA_PBURST_SINGLE ((uint32_t)0x00000000U) -#define DMA_PBURST_INC4 ((uint32_t)DMA_SxCR_PBURST_0) -#define DMA_PBURST_INC8 ((uint32_t)DMA_SxCR_PBURST_1) -#define DMA_PBURST_INC16 ((uint32_t)DMA_SxCR_PBURST) -/** - * @} - */ - -/** @defgroup DMA_interrupt_enable_definitions DMA interrupt enable definitions - * @brief DMA interrupts definition - * @{ - */ -#define DMA_IT_TC ((uint32_t)DMA_SxCR_TCIE) -#define DMA_IT_HT ((uint32_t)DMA_SxCR_HTIE) -#define DMA_IT_TE ((uint32_t)DMA_SxCR_TEIE) -#define DMA_IT_DME ((uint32_t)DMA_SxCR_DMEIE) -#define DMA_IT_FE ((uint32_t)0x00000080U) -/** - * @} - */ - -/** @defgroup DMA_flag_definitions DMA flag definitions - * @brief DMA flag definitions - * @{ - */ -#define DMA_FLAG_FEIF0_4 ((uint32_t)0x00800001U) -#define DMA_FLAG_DMEIF0_4 ((uint32_t)0x00800004U) -#define DMA_FLAG_TEIF0_4 ((uint32_t)0x00000008U) -#define DMA_FLAG_HTIF0_4 ((uint32_t)0x00000010U) -#define DMA_FLAG_TCIF0_4 ((uint32_t)0x00000020U) -#define DMA_FLAG_FEIF1_5 ((uint32_t)0x00000040U) -#define DMA_FLAG_DMEIF1_5 ((uint32_t)0x00000100U) -#define DMA_FLAG_TEIF1_5 ((uint32_t)0x00000200U) -#define DMA_FLAG_HTIF1_5 ((uint32_t)0x00000400U) -#define DMA_FLAG_TCIF1_5 ((uint32_t)0x00000800U) -#define DMA_FLAG_FEIF2_6 ((uint32_t)0x00010000U) -#define DMA_FLAG_DMEIF2_6 ((uint32_t)0x00040000U) -#define DMA_FLAG_TEIF2_6 ((uint32_t)0x00080000U) -#define DMA_FLAG_HTIF2_6 ((uint32_t)0x00100000U) -#define DMA_FLAG_TCIF2_6 ((uint32_t)0x00200000U) -#define DMA_FLAG_FEIF3_7 ((uint32_t)0x00400000U) -#define DMA_FLAG_DMEIF3_7 ((uint32_t)0x01000000U) -#define DMA_FLAG_TEIF3_7 ((uint32_t)0x02000000U) -#define DMA_FLAG_HTIF3_7 ((uint32_t)0x04000000U) -#define DMA_FLAG_TCIF3_7 ((uint32_t)0x08000000U) -/** - * @} - */ - -/** - * @} - */ - -/* Exported macro ------------------------------------------------------------*/ - -/** @brief Reset DMA handle state - * @param __HANDLE__: specifies the DMA handle. - * @retval None - */ -#define __HAL_DMA_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_DMA_STATE_RESET) - -/** - * @brief Return the current DMA Stream FIFO filled level. - * @param __HANDLE__: DMA handle - * @retval The FIFO filling state. - * - DMA_FIFOStatus_Less1QuarterFull: when FIFO is less than 1 quarter-full - * and not empty. - * - DMA_FIFOStatus_1QuarterFull: if more than 1 quarter-full. - * - DMA_FIFOStatus_HalfFull: if more than 1 half-full. - * - DMA_FIFOStatus_3QuartersFull: if more than 3 quarters-full. - * - DMA_FIFOStatus_Empty: when FIFO is empty - * - DMA_FIFOStatus_Full: when FIFO is full - */ -#define __HAL_DMA_GET_FS(__HANDLE__) (((__HANDLE__)->Instance->FCR & (DMA_SxFCR_FS))) - -/** - * @brief Enable the specified DMA Stream. - * @param __HANDLE__: DMA handle - * @retval None - */ -#define __HAL_DMA_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR |= DMA_SxCR_EN) - -/** - * @brief Disable the specified DMA Stream. - * @param __HANDLE__: DMA handle - * @retval None - */ -#define __HAL_DMA_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR &= ~DMA_SxCR_EN) - -/* Interrupt & Flag management */ - -/** - * @brief Return the current DMA Stream transfer complete flag. - * @param __HANDLE__: DMA handle - * @retval The specified transfer complete flag index. - */ -#define __HAL_DMA_GET_TC_FLAG_INDEX(__HANDLE__) \ -(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream0))? DMA_FLAG_TCIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream0))? DMA_FLAG_TCIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream4))? DMA_FLAG_TCIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream4))? DMA_FLAG_TCIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream1))? DMA_FLAG_TCIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream1))? DMA_FLAG_TCIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream5))? DMA_FLAG_TCIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream5))? DMA_FLAG_TCIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream2))? DMA_FLAG_TCIF2_6 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream2))? DMA_FLAG_TCIF2_6 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream6))? DMA_FLAG_TCIF2_6 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream6))? DMA_FLAG_TCIF2_6 :\ - DMA_FLAG_TCIF3_7) - -/** - * @brief Return the current DMA Stream half transfer complete flag. - * @param __HANDLE__: DMA handle - * @retval The specified half transfer complete flag index. - */ -#define __HAL_DMA_GET_HT_FLAG_INDEX(__HANDLE__)\ -(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream0))? DMA_FLAG_HTIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream0))? DMA_FLAG_HTIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream4))? DMA_FLAG_HTIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream4))? DMA_FLAG_HTIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream1))? DMA_FLAG_HTIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream1))? DMA_FLAG_HTIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream5))? DMA_FLAG_HTIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream5))? DMA_FLAG_HTIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream2))? DMA_FLAG_HTIF2_6 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream2))? DMA_FLAG_HTIF2_6 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream6))? DMA_FLAG_HTIF2_6 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream6))? DMA_FLAG_HTIF2_6 :\ - DMA_FLAG_HTIF3_7) - -/** - * @brief Return the current DMA Stream transfer error flag. - * @param __HANDLE__: DMA handle - * @retval The specified transfer error flag index. - */ -#define __HAL_DMA_GET_TE_FLAG_INDEX(__HANDLE__)\ -(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream0))? DMA_FLAG_TEIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream0))? DMA_FLAG_TEIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream4))? DMA_FLAG_TEIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream4))? DMA_FLAG_TEIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream1))? DMA_FLAG_TEIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream1))? DMA_FLAG_TEIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream5))? DMA_FLAG_TEIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream5))? DMA_FLAG_TEIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream2))? DMA_FLAG_TEIF2_6 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream2))? DMA_FLAG_TEIF2_6 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream6))? DMA_FLAG_TEIF2_6 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream6))? DMA_FLAG_TEIF2_6 :\ - DMA_FLAG_TEIF3_7) - -/** - * @brief Return the current DMA Stream FIFO error flag. - * @param __HANDLE__: DMA handle - * @retval The specified FIFO error flag index. - */ -#define __HAL_DMA_GET_FE_FLAG_INDEX(__HANDLE__)\ -(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream0))? DMA_FLAG_FEIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream0))? DMA_FLAG_FEIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream4))? DMA_FLAG_FEIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream4))? DMA_FLAG_FEIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream1))? DMA_FLAG_FEIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream1))? DMA_FLAG_FEIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream5))? DMA_FLAG_FEIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream5))? DMA_FLAG_FEIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream2))? DMA_FLAG_FEIF2_6 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream2))? DMA_FLAG_FEIF2_6 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream6))? DMA_FLAG_FEIF2_6 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream6))? DMA_FLAG_FEIF2_6 :\ - DMA_FLAG_FEIF3_7) - -/** - * @brief Return the current DMA Stream direct mode error flag. - * @param __HANDLE__: DMA handle - * @retval The specified direct mode error flag index. - */ -#define __HAL_DMA_GET_DME_FLAG_INDEX(__HANDLE__)\ -(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream0))? DMA_FLAG_DMEIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream0))? DMA_FLAG_DMEIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream4))? DMA_FLAG_DMEIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream4))? DMA_FLAG_DMEIF0_4 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream1))? DMA_FLAG_DMEIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream1))? DMA_FLAG_DMEIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream5))? DMA_FLAG_DMEIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream5))? DMA_FLAG_DMEIF1_5 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream2))? DMA_FLAG_DMEIF2_6 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream2))? DMA_FLAG_DMEIF2_6 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream6))? DMA_FLAG_DMEIF2_6 :\ - ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream6))? DMA_FLAG_DMEIF2_6 :\ - DMA_FLAG_DMEIF3_7) - -/** - * @brief Get the DMA Stream pending flags. - * @param __HANDLE__: DMA handle - * @param __FLAG__: Get the specified flag. - * This parameter can be any combination of the following values: - * @arg DMA_FLAG_TCIFx: Transfer complete flag. - * @arg DMA_FLAG_HTIFx: Half transfer complete flag. - * @arg DMA_FLAG_TEIFx: Transfer error flag. - * @arg DMA_FLAG_DMEIFx: Direct mode error flag. - * @arg DMA_FLAG_FEIFx: FIFO error flag. - * Where x can be 0_4, 1_5, 2_6 or 3_7 to select the DMA Stream flag. - * @retval The state of FLAG (SET or RESET). - */ -#define __HAL_DMA_GET_FLAG(__HANDLE__, __FLAG__)\ -(((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA2_Stream3)? (DMA2->HISR & (__FLAG__)) :\ - ((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA1_Stream7)? (DMA2->LISR & (__FLAG__)) :\ - ((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA1_Stream3)? (DMA1->HISR & (__FLAG__)) : (DMA1->LISR & (__FLAG__))) - -/** - * @brief Clear the DMA Stream pending flags. - * @param __HANDLE__: DMA handle - * @param __FLAG__: specifies the flag to clear. - * This parameter can be any combination of the following values: - * @arg DMA_FLAG_TCIFx: Transfer complete flag. - * @arg DMA_FLAG_HTIFx: Half transfer complete flag. - * @arg DMA_FLAG_TEIFx: Transfer error flag. - * @arg DMA_FLAG_DMEIFx: Direct mode error flag. - * @arg DMA_FLAG_FEIFx: FIFO error flag. - * Where x can be 0_4, 1_5, 2_6 or 3_7 to select the DMA Stream flag. - * @retval None - */ -#define __HAL_DMA_CLEAR_FLAG(__HANDLE__, __FLAG__) \ -(((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA2_Stream3)? (DMA2->HIFCR = (__FLAG__)) :\ - ((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA1_Stream7)? (DMA2->LIFCR = (__FLAG__)) :\ - ((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA1_Stream3)? (DMA1->HIFCR = (__FLAG__)) : (DMA1->LIFCR = (__FLAG__))) - -/** - * @brief Enable the specified DMA Stream interrupts. - * @param __HANDLE__: DMA handle - * @param __INTERRUPT__: specifies the DMA interrupt sources to be enabled or disabled. - * This parameter can be any combination of the following values: - * @arg DMA_IT_TC: Transfer complete interrupt mask. - * @arg DMA_IT_HT: Half transfer complete interrupt mask. - * @arg DMA_IT_TE: Transfer error interrupt mask. - * @arg DMA_IT_FE: FIFO error interrupt mask. - * @arg DMA_IT_DME: Direct mode error interrupt. - * @retval None - */ -#define __HAL_DMA_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((__INTERRUPT__) != DMA_IT_FE)? \ -((__HANDLE__)->Instance->CR |= (__INTERRUPT__)) : ((__HANDLE__)->Instance->FCR |= (__INTERRUPT__))) - -/** - * @brief Disable the specified DMA Stream interrupts. - * @param __HANDLE__: DMA handle - * @param __INTERRUPT__: specifies the DMA interrupt sources to be enabled or disabled. - * This parameter can be any combination of the following values: - * @arg DMA_IT_TC: Transfer complete interrupt mask. - * @arg DMA_IT_HT: Half transfer complete interrupt mask. - * @arg DMA_IT_TE: Transfer error interrupt mask. - * @arg DMA_IT_FE: FIFO error interrupt mask. - * @arg DMA_IT_DME: Direct mode error interrupt. - * @retval None - */ -#define __HAL_DMA_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((__INTERRUPT__) != DMA_IT_FE)? \ -((__HANDLE__)->Instance->CR &= ~(__INTERRUPT__)) : ((__HANDLE__)->Instance->FCR &= ~(__INTERRUPT__))) - -/** - * @brief Check whether the specified DMA Stream interrupt is enabled or disabled. - * @param __HANDLE__: DMA handle - * @param __INTERRUPT__: specifies the DMA interrupt source to check. - * This parameter can be one of the following values: - * @arg DMA_IT_TC: Transfer complete interrupt mask. - * @arg DMA_IT_HT: Half transfer complete interrupt mask. - * @arg DMA_IT_TE: Transfer error interrupt mask. - * @arg DMA_IT_FE: FIFO error interrupt mask. - * @arg DMA_IT_DME: Direct mode error interrupt. - * @retval The state of DMA_IT. - */ -#define __HAL_DMA_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) (((__INTERRUPT__) != DMA_IT_FE)? \ - ((__HANDLE__)->Instance->CR & (__INTERRUPT__)) : \ - ((__HANDLE__)->Instance->FCR & (__INTERRUPT__))) - -/** - * @brief Writes the number of data units to be transferred on the DMA Stream. - * @param __HANDLE__: DMA handle - * @param __COUNTER__: Number of data units to be transferred (from 0 to 65535) - * Number of data items depends only on the Peripheral data format. - * - * @note If Peripheral data format is Bytes: number of data units is equal - * to total number of bytes to be transferred. - * - * @note If Peripheral data format is Half-Word: number of data units is - * equal to total number of bytes to be transferred / 2. - * - * @note If Peripheral data format is Word: number of data units is equal - * to total number of bytes to be transferred / 4. - * - * @retval The number of remaining data units in the current DMAy Streamx transfer. - */ -#define __HAL_DMA_SET_COUNTER(__HANDLE__, __COUNTER__) ((__HANDLE__)->Instance->NDTR = (uint16_t)(__COUNTER__)) - -/** - * @brief Returns the number of remaining data units in the current DMAy Streamx transfer. - * @param __HANDLE__: DMA handle - * - * @retval The number of remaining data units in the current DMA Stream transfer. - */ -#define __HAL_DMA_GET_COUNTER(__HANDLE__) ((__HANDLE__)->Instance->NDTR) - - -/* Include DMA HAL Extension module */ -#include "stm32f4xx_hal_dma_ex.h" - -/* Exported functions --------------------------------------------------------*/ - -/** @defgroup DMA_Exported_Functions DMA Exported Functions - * @brief DMA Exported functions - * @{ - */ - -/** @defgroup DMA_Exported_Functions_Group1 Initialization and de-initialization functions - * @brief Initialization and de-initialization functions - * @{ - */ -HAL_StatusTypeDef HAL_DMA_Init(DMA_HandleTypeDef* hdma); -HAL_StatusTypeDef HAL_DMA_DeInit(DMA_HandleTypeDef* hdma); -/** - * @} - */ - -/** @defgroup DMA_Exported_Functions_Group2 I/O operation functions - * @brief I/O operation functions - * @{ - */ -HAL_StatusTypeDef HAL_DMA_Start (DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength); -HAL_StatusTypeDef HAL_DMA_Start_IT(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength); -HAL_StatusTypeDef HAL_DMA_Abort(DMA_HandleTypeDef* hdma); -HAL_StatusTypeDef HAL_DMA_Abort_IT(DMA_HandleTypeDef* hdma); -HAL_StatusTypeDef HAL_DMA_PollForTransfer(DMA_HandleTypeDef* hdma, HAL_DMA_LevelCompleteTypeDef CompleteLevel, uint32_t Timeout); -void HAL_DMA_IRQHandler(DMA_HandleTypeDef* hdma); -HAL_StatusTypeDef HAL_DMA_CleanCallbacks(DMA_HandleTypeDef* hdma); -HAL_StatusTypeDef HAL_DMA_RegisterCallback(DMA_HandleTypeDef* hdma, HAL_DMA_CallbackIDTypeDef CallbackID, void (* pCallback)(DMA_HandleTypeDef* _hdma)); -HAL_StatusTypeDef HAL_DMA_UnRegisterCallback(DMA_HandleTypeDef* hdma, HAL_DMA_CallbackIDTypeDef CallbackID); - -/** - * @} - */ - -/** @defgroup DMA_Exported_Functions_Group3 Peripheral State functions - * @brief Peripheral State functions - * @{ - */ -HAL_DMA_StateTypeDef HAL_DMA_GetState(DMA_HandleTypeDef* hdma); -uint32_t HAL_DMA_GetError(DMA_HandleTypeDef* hdma); -/** - * @} - */ -/** - * @} - */ -/* Private Constants -------------------------------------------------------------*/ -/** @defgroup DMA_Private_Constants DMA Private Constants - * @brief DMA private defines and constants - * @{ - */ -/** - * @} - */ - -/* Private macros ------------------------------------------------------------*/ -/** @defgroup DMA_Private_Macros DMA Private Macros - * @brief DMA private macros - * @{ - */ -#define IS_DMA_CHANNEL(CHANNEL) (((CHANNEL) == DMA_CHANNEL_0) || \ - ((CHANNEL) == DMA_CHANNEL_1) || \ - ((CHANNEL) == DMA_CHANNEL_2) || \ - ((CHANNEL) == DMA_CHANNEL_3) || \ - ((CHANNEL) == DMA_CHANNEL_4) || \ - ((CHANNEL) == DMA_CHANNEL_5) || \ - ((CHANNEL) == DMA_CHANNEL_6) || \ - ((CHANNEL) == DMA_CHANNEL_7)) - -#define IS_DMA_DIRECTION(DIRECTION) (((DIRECTION) == DMA_PERIPH_TO_MEMORY ) || \ - ((DIRECTION) == DMA_MEMORY_TO_PERIPH) || \ - ((DIRECTION) == DMA_MEMORY_TO_MEMORY)) - -#define IS_DMA_BUFFER_SIZE(SIZE) (((SIZE) >= 0x01U) && ((SIZE) < 0x10000U)) - -#define IS_DMA_PERIPHERAL_INC_STATE(STATE) (((STATE) == DMA_PINC_ENABLE) || \ - ((STATE) == DMA_PINC_DISABLE)) - -#define IS_DMA_MEMORY_INC_STATE(STATE) (((STATE) == DMA_MINC_ENABLE) || \ - ((STATE) == DMA_MINC_DISABLE)) - -#define IS_DMA_PERIPHERAL_DATA_SIZE(SIZE) (((SIZE) == DMA_PDATAALIGN_BYTE) || \ - ((SIZE) == DMA_PDATAALIGN_HALFWORD) || \ - ((SIZE) == DMA_PDATAALIGN_WORD)) - -#define IS_DMA_MEMORY_DATA_SIZE(SIZE) (((SIZE) == DMA_MDATAALIGN_BYTE) || \ - ((SIZE) == DMA_MDATAALIGN_HALFWORD) || \ - ((SIZE) == DMA_MDATAALIGN_WORD )) - -#define IS_DMA_MODE(MODE) (((MODE) == DMA_NORMAL ) || \ - ((MODE) == DMA_CIRCULAR) || \ - ((MODE) == DMA_PFCTRL)) - -#define IS_DMA_PRIORITY(PRIORITY) (((PRIORITY) == DMA_PRIORITY_LOW ) || \ - ((PRIORITY) == DMA_PRIORITY_MEDIUM) || \ - ((PRIORITY) == DMA_PRIORITY_HIGH) || \ - ((PRIORITY) == DMA_PRIORITY_VERY_HIGH)) - -#define IS_DMA_FIFO_MODE_STATE(STATE) (((STATE) == DMA_FIFOMODE_DISABLE ) || \ - ((STATE) == DMA_FIFOMODE_ENABLE)) - -#define IS_DMA_FIFO_THRESHOLD(THRESHOLD) (((THRESHOLD) == DMA_FIFO_THRESHOLD_1QUARTERFULL ) || \ - ((THRESHOLD) == DMA_FIFO_THRESHOLD_HALFFULL) || \ - ((THRESHOLD) == DMA_FIFO_THRESHOLD_3QUARTERSFULL) || \ - ((THRESHOLD) == DMA_FIFO_THRESHOLD_FULL)) - -#define IS_DMA_MEMORY_BURST(BURST) (((BURST) == DMA_MBURST_SINGLE) || \ - ((BURST) == DMA_MBURST_INC4) || \ - ((BURST) == DMA_MBURST_INC8) || \ - ((BURST) == DMA_MBURST_INC16)) - -#define IS_DMA_PERIPHERAL_BURST(BURST) (((BURST) == DMA_PBURST_SINGLE) || \ - ((BURST) == DMA_PBURST_INC4) || \ - ((BURST) == DMA_PBURST_INC8) || \ - ((BURST) == DMA_PBURST_INC16)) -/** - * @} - */ - -/* Private functions ---------------------------------------------------------*/ -/** @defgroup DMA_Private_Functions DMA Private Functions - * @brief DMA private functions - * @{ - */ -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F4xx_HAL_DMA_H */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_dma_ex.h b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_dma_ex.h deleted file mode 100644 index b8b3a7fc..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_dma_ex.h +++ /dev/null @@ -1,122 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_dma_ex.h - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Header file of DMA HAL extension module. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_DMA_EX_H -#define __STM32F4xx_HAL_DMA_EX_H - -#ifdef __cplusplus -extern "C" { -#endif - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_def.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @addtogroup DMAEx - * @{ - */ - -/* Exported types ------------------------------------------------------------*/ -/** @defgroup DMAEx_Exported_Types DMAEx Exported Types - * @brief DMAEx Exported types - * @{ - */ - -/** - * @brief HAL DMA Memory definition - */ -typedef enum -{ - MEMORY0 = 0x00U, /*!< Memory 0 */ - MEMORY1 = 0x01U /*!< Memory 1 */ -} HAL_DMA_MemoryTypeDef; - -/** - * @} - */ - -/* Exported functions --------------------------------------------------------*/ -/** @defgroup DMAEx_Exported_Functions DMAEx Exported Functions - * @brief DMAEx Exported functions - * @{ - */ - -/** @defgroup DMAEx_Exported_Functions_Group1 Extended features functions - * @brief Extended features functions - * @{ - */ - -/* IO operation functions *******************************************************/ -HAL_StatusTypeDef HAL_DMAEx_MultiBufferStart(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t SecondMemAddress, uint32_t DataLength); -HAL_StatusTypeDef HAL_DMAEx_MultiBufferStart_IT(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t SecondMemAddress, uint32_t DataLength); -HAL_StatusTypeDef HAL_DMAEx_ChangeMemory(DMA_HandleTypeDef* hdma, uint32_t Address, HAL_DMA_MemoryTypeDef memory); - -/** - * @} - */ -/** - * @} - */ - -/* Private functions ---------------------------------------------------------*/ -/** @defgroup DMAEx_Private_Functions DMAEx Private Functions - * @brief DMAEx Private functions - * @{ - */ -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -#ifdef __cplusplus -} -#endif - -#endif /*__STM32F4xx_HAL_DMA_EX_H*/ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash.h b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash.h deleted file mode 100644 index 7c1ef442..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash.h +++ /dev/null @@ -1,442 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_flash.h - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Header file of FLASH HAL module. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_FLASH_H -#define __STM32F4xx_HAL_FLASH_H - -#ifdef __cplusplus -extern "C" { -#endif - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_def.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @addtogroup FLASH - * @{ - */ - -/* Exported types ------------------------------------------------------------*/ -/** @defgroup FLASH_Exported_Types FLASH Exported Types - * @{ - */ - -/** - * @brief FLASH Procedure structure definition - */ -typedef enum -{ - FLASH_PROC_NONE = 0U, - FLASH_PROC_SECTERASE, - FLASH_PROC_MASSERASE, - FLASH_PROC_PROGRAM -} FLASH_ProcedureTypeDef; - -/** - * @brief FLASH handle Structure definition - */ -typedef struct -{ - __IO FLASH_ProcedureTypeDef ProcedureOnGoing; /*Internal variable to indicate which procedure is ongoing or not in IT context*/ - - __IO uint32_t NbSectorsToErase; /*Internal variable to save the remaining sectors to erase in IT context*/ - - __IO uint8_t VoltageForErase; /*Internal variable to provide voltage range selected by user in IT context*/ - - __IO uint32_t Sector; /*Internal variable to define the current sector which is erasing*/ - - __IO uint32_t Bank; /*Internal variable to save current bank selected during mass erase*/ - - __IO uint32_t Address; /*Internal variable to save address selected for program*/ - - HAL_LockTypeDef Lock; /* FLASH locking object */ - - __IO uint32_t ErrorCode; /* FLASH error code */ - -} FLASH_ProcessTypeDef; - -/** - * @} - */ - -/* Exported constants --------------------------------------------------------*/ -/** @defgroup FLASH_Exported_Constants FLASH Exported Constants - * @{ - */ -/** @defgroup FLASH_Error_Code FLASH Error Code - * @brief FLASH Error Code - * @{ - */ -#define HAL_FLASH_ERROR_NONE ((uint32_t)0x00000000U) /*!< No error */ -#define HAL_FLASH_ERROR_RD ((uint32_t)0x00000001U) /*!< Read Protection error */ -#define HAL_FLASH_ERROR_PGS ((uint32_t)0x00000002U) /*!< Programming Sequence error */ -#define HAL_FLASH_ERROR_PGP ((uint32_t)0x00000004U) /*!< Programming Parallelism error */ -#define HAL_FLASH_ERROR_PGA ((uint32_t)0x00000008U) /*!< Programming Alignment error */ -#define HAL_FLASH_ERROR_WRP ((uint32_t)0x00000010U) /*!< Write protection error */ -#define HAL_FLASH_ERROR_OPERATION ((uint32_t)0x00000020U) /*!< Operation Error */ -/** - * @} - */ - -/** @defgroup FLASH_Type_Program FLASH Type Program - * @{ - */ -#define FLASH_TYPEPROGRAM_BYTE ((uint32_t)0x00U) /*!< Program byte (8-bit) at a specified address */ -#define FLASH_TYPEPROGRAM_HALFWORD ((uint32_t)0x01U) /*!< Program a half-word (16-bit) at a specified address */ -#define FLASH_TYPEPROGRAM_WORD ((uint32_t)0x02U) /*!< Program a word (32-bit) at a specified address */ -#define FLASH_TYPEPROGRAM_DOUBLEWORD ((uint32_t)0x03U) /*!< Program a double word (64-bit) at a specified address */ -/** - * @} - */ - -/** @defgroup FLASH_Flag_definition FLASH Flag definition - * @brief Flag definition - * @{ - */ -#define FLASH_FLAG_EOP FLASH_SR_EOP /*!< FLASH End of Operation flag */ -#define FLASH_FLAG_OPERR FLASH_SR_SOP /*!< FLASH operation Error flag */ -#define FLASH_FLAG_WRPERR FLASH_SR_WRPERR /*!< FLASH Write protected error flag */ -#define FLASH_FLAG_PGAERR FLASH_SR_PGAERR /*!< FLASH Programming Alignment error flag */ -#define FLASH_FLAG_PGPERR FLASH_SR_PGPERR /*!< FLASH Programming Parallelism error flag */ -#define FLASH_FLAG_PGSERR FLASH_SR_PGSERR /*!< FLASH Programming Sequence error flag */ -#define FLASH_FLAG_RDERR ((uint32_t)0x00000100U) /*!< Read Protection error flag (PCROP) */ -#define FLASH_FLAG_BSY FLASH_SR_BSY /*!< FLASH Busy flag */ -/** - * @} - */ - -/** @defgroup FLASH_Interrupt_definition FLASH Interrupt definition - * @brief FLASH Interrupt definition - * @{ - */ -#define FLASH_IT_EOP FLASH_CR_EOPIE /*!< End of FLASH Operation Interrupt source */ -#define FLASH_IT_ERR ((uint32_t)0x02000000U) /*!< Error Interrupt source */ -/** - * @} - */ - -/** @defgroup FLASH_Program_Parallelism FLASH Program Parallelism - * @{ - */ -#define FLASH_PSIZE_BYTE ((uint32_t)0x00000000U) -#define FLASH_PSIZE_HALF_WORD ((uint32_t)0x00000100U) -#define FLASH_PSIZE_WORD ((uint32_t)0x00000200U) -#define FLASH_PSIZE_DOUBLE_WORD ((uint32_t)0x00000300U) -#define CR_PSIZE_MASK ((uint32_t)0xFFFFFCFFU) -/** - * @} - */ - -/** @defgroup FLASH_Keys FLASH Keys - * @{ - */ -#define RDP_KEY ((uint16_t)0x00A5U) -#define FLASH_KEY1 ((uint32_t)0x45670123U) -#define FLASH_KEY2 ((uint32_t)0xCDEF89ABU) -#define FLASH_OPT_KEY1 ((uint32_t)0x08192A3BU) -#define FLASH_OPT_KEY2 ((uint32_t)0x4C5D6E7FU) -/** - * @} - */ - -/** - * @} - */ - -/* Exported macro ------------------------------------------------------------*/ -/** @defgroup FLASH_Exported_Macros FLASH Exported Macros - * @{ - */ -/** - * @brief Set the FLASH Latency. - * @param __LATENCY__: FLASH Latency - * The value of this parameter depend on device used within the same series - * @retval none - */ -#define __HAL_FLASH_SET_LATENCY(__LATENCY__) (*(__IO uint8_t *)ACR_BYTE0_ADDRESS = (uint8_t)(__LATENCY__)) - -/** - * @brief Get the FLASH Latency. - * @retval FLASH Latency - * The value of this parameter depend on device used within the same series - */ -#define __HAL_FLASH_GET_LATENCY() (READ_BIT((FLASH->ACR), FLASH_ACR_LATENCY)) - -/** - * @brief Enable the FLASH prefetch buffer. - * @retval none - */ -#define __HAL_FLASH_PREFETCH_BUFFER_ENABLE() (FLASH->ACR |= FLASH_ACR_PRFTEN) - -/** - * @brief Disable the FLASH prefetch buffer. - * @retval none - */ -#define __HAL_FLASH_PREFETCH_BUFFER_DISABLE() (FLASH->ACR &= (~FLASH_ACR_PRFTEN)) - -/** - * @brief Enable the FLASH instruction cache. - * @retval none - */ -#define __HAL_FLASH_INSTRUCTION_CACHE_ENABLE() (FLASH->ACR |= FLASH_ACR_ICEN) - -/** - * @brief Disable the FLASH instruction cache. - * @retval none - */ -#define __HAL_FLASH_INSTRUCTION_CACHE_DISABLE() (FLASH->ACR &= (~FLASH_ACR_ICEN)) - -/** - * @brief Enable the FLASH data cache. - * @retval none - */ -#define __HAL_FLASH_DATA_CACHE_ENABLE() (FLASH->ACR |= FLASH_ACR_DCEN) - -/** - * @brief Disable the FLASH data cache. - * @retval none - */ -#define __HAL_FLASH_DATA_CACHE_DISABLE() (FLASH->ACR &= (~FLASH_ACR_DCEN)) - -/** - * @brief Resets the FLASH instruction Cache. - * @note This function must be used only when the Instruction Cache is disabled. - * @retval None - */ -#define __HAL_FLASH_INSTRUCTION_CACHE_RESET() do {FLASH->ACR |= FLASH_ACR_ICRST; \ - FLASH->ACR &= ~FLASH_ACR_ICRST; \ - }while(0) - -/** - * @brief Resets the FLASH data Cache. - * @note This function must be used only when the data Cache is disabled. - * @retval None - */ -#define __HAL_FLASH_DATA_CACHE_RESET() do {FLASH->ACR |= FLASH_ACR_DCRST; \ - FLASH->ACR &= ~FLASH_ACR_DCRST; \ - }while(0) -/** - * @brief Enable the specified FLASH interrupt. - * @param __INTERRUPT__ : FLASH interrupt - * This parameter can be any combination of the following values: - * @arg FLASH_IT_EOP: End of FLASH Operation Interrupt - * @arg FLASH_IT_ERR: Error Interrupt - * @retval none - */ -#define __HAL_FLASH_ENABLE_IT(__INTERRUPT__) (FLASH->CR |= (__INTERRUPT__)) - -/** - * @brief Disable the specified FLASH interrupt. - * @param __INTERRUPT__ : FLASH interrupt - * This parameter can be any combination of the following values: - * @arg FLASH_IT_EOP: End of FLASH Operation Interrupt - * @arg FLASH_IT_ERR: Error Interrupt - * @retval none - */ -#define __HAL_FLASH_DISABLE_IT(__INTERRUPT__) (FLASH->CR &= ~(uint32_t)(__INTERRUPT__)) - -/** - * @brief Get the specified FLASH flag status. - * @param __FLAG__: specifies the FLASH flag to check. - * This parameter can be one of the following values: - * @arg FLASH_FLAG_EOP : FLASH End of Operation flag - * @arg FLASH_FLAG_OPERR : FLASH operation Error flag - * @arg FLASH_FLAG_WRPERR: FLASH Write protected error flag - * @arg FLASH_FLAG_PGAERR: FLASH Programming Alignment error flag - * @arg FLASH_FLAG_PGPERR: FLASH Programming Parallelism error flag - * @arg FLASH_FLAG_PGSERR: FLASH Programming Sequence error flag - * @arg FLASH_FLAG_RDERR : FLASH Read Protection error flag (PCROP) - * @arg FLASH_FLAG_BSY : FLASH Busy flag - * @retval The new state of __FLAG__ (SET or RESET). - */ -#define __HAL_FLASH_GET_FLAG(__FLAG__) ((FLASH->SR & (__FLAG__))==(__FLAG__)) - -/** - * @brief Clear the specified FLASH flag. - * @param __FLAG__: specifies the FLASH flags to clear. - * This parameter can be any combination of the following values: - * @arg FLASH_FLAG_EOP : FLASH End of Operation flag - * @arg FLASH_FLAG_OPERR : FLASH operation Error flag - * @arg FLASH_FLAG_WRPERR: FLASH Write protected error flag - * @arg FLASH_FLAG_PGAERR: FLASH Programming Alignment error flag - * @arg FLASH_FLAG_PGPERR: FLASH Programming Parallelism error flag - * @arg FLASH_FLAG_PGSERR: FLASH Programming Sequence error flag - * @arg FLASH_FLAG_RDERR : FLASH Read Protection error flag (PCROP) - * @retval none - */ -#define __HAL_FLASH_CLEAR_FLAG(__FLAG__) (FLASH->SR = (__FLAG__)) -/** - * @} - */ - -/* Include FLASH HAL Extension module */ -#include "stm32f4xx_hal_flash_ex.h" -#include "stm32f4xx_hal_flash_ramfunc.h" - -/* Exported functions --------------------------------------------------------*/ -/** @addtogroup FLASH_Exported_Functions - * @{ - */ -/** @addtogroup FLASH_Exported_Functions_Group1 - * @{ - */ -/* Program operation functions ***********************************************/ -HAL_StatusTypeDef HAL_FLASH_Program(uint32_t TypeProgram, uint32_t Address, uint64_t Data); -HAL_StatusTypeDef HAL_FLASH_Program_IT(uint32_t TypeProgram, uint32_t Address, uint64_t Data); -/* FLASH IRQ handler method */ -void HAL_FLASH_IRQHandler(void); -/* Callbacks in non blocking modes */ -void HAL_FLASH_EndOfOperationCallback(uint32_t ReturnValue); -void HAL_FLASH_OperationErrorCallback(uint32_t ReturnValue); -/** - * @} - */ - -/** @addtogroup FLASH_Exported_Functions_Group2 - * @{ - */ -/* Peripheral Control functions **********************************************/ -HAL_StatusTypeDef HAL_FLASH_Unlock(void); -HAL_StatusTypeDef HAL_FLASH_Lock(void); -HAL_StatusTypeDef HAL_FLASH_OB_Unlock(void); -HAL_StatusTypeDef HAL_FLASH_OB_Lock(void); -/* Option bytes control */ -HAL_StatusTypeDef HAL_FLASH_OB_Launch(void); -/** - * @} - */ - -/** @addtogroup FLASH_Exported_Functions_Group3 - * @{ - */ -/* Peripheral State functions ************************************************/ -uint32_t HAL_FLASH_GetError(void); -HAL_StatusTypeDef FLASH_WaitForLastOperation(uint32_t Timeout); -/** - * @} - */ - -/** - * @} - */ -/* Private types -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/** @defgroup FLASH_Private_Variables FLASH Private Variables - * @{ - */ - -/** - * @} - */ -/* Private constants ---------------------------------------------------------*/ -/** @defgroup FLASH_Private_Constants FLASH Private Constants - * @{ - */ - -/** - * @brief ACR register byte 0 (Bits[7:0]) base address - */ -#define ACR_BYTE0_ADDRESS ((uint32_t)0x40023C00U) -/** - * @brief OPTCR register byte 0 (Bits[7:0]) base address - */ -#define OPTCR_BYTE0_ADDRESS ((uint32_t)0x40023C14U) -/** - * @brief OPTCR register byte 1 (Bits[15:8]) base address - */ -#define OPTCR_BYTE1_ADDRESS ((uint32_t)0x40023C15U) -/** - * @brief OPTCR register byte 2 (Bits[23:16]) base address - */ -#define OPTCR_BYTE2_ADDRESS ((uint32_t)0x40023C16U) -/** - * @brief OPTCR register byte 3 (Bits[31:24]) base address - */ -#define OPTCR_BYTE3_ADDRESS ((uint32_t)0x40023C17U) - -/** - * @} - */ - -/* Private macros ------------------------------------------------------------*/ -/** @defgroup FLASH_Private_Macros FLASH Private Macros - * @{ - */ - -/** @defgroup FLASH_IS_FLASH_Definitions FLASH Private macros to check input parameters - * @{ - */ -#define IS_FLASH_TYPEPROGRAM(VALUE)(((VALUE) == FLASH_TYPEPROGRAM_BYTE) || \ - ((VALUE) == FLASH_TYPEPROGRAM_HALFWORD) || \ - ((VALUE) == FLASH_TYPEPROGRAM_WORD) || \ - ((VALUE) == FLASH_TYPEPROGRAM_DOUBLEWORD)) -/** - * @} - */ - -/** - * @} - */ - -/* Private functions ---------------------------------------------------------*/ -/** @defgroup FLASH_Private_Functions FLASH Private Functions - * @{ - */ - -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F4xx_HAL_FLASH_H */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash_ex.h b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash_ex.h deleted file mode 100644 index d4063d82..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash_ex.h +++ /dev/null @@ -1,984 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_flash_ex.h - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Header file of FLASH HAL Extension module. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_FLASH_EX_H -#define __STM32F4xx_HAL_FLASH_EX_H - -#ifdef __cplusplus -extern "C" { -#endif - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_def.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @addtogroup FLASHEx - * @{ - */ - -/* Exported types ------------------------------------------------------------*/ -/** @defgroup FLASHEx_Exported_Types FLASH Exported Types - * @{ - */ - -/** - * @brief FLASH Erase structure definition - */ -typedef struct -{ - uint32_t TypeErase; /*!< Mass erase or sector Erase. - This parameter can be a value of @ref FLASHEx_Type_Erase */ - - uint32_t Banks; /*!< Select banks to erase when Mass erase is enabled. - This parameter must be a value of @ref FLASHEx_Banks */ - - uint32_t Sector; /*!< Initial FLASH sector to erase when Mass erase is disabled - This parameter must be a value of @ref FLASHEx_Sectors */ - - uint32_t NbSectors; /*!< Number of sectors to be erased. - This parameter must be a value between 1 and (max number of sectors - value of Initial sector)*/ - - uint32_t VoltageRange;/*!< The device voltage range which defines the erase parallelism - This parameter must be a value of @ref FLASHEx_Voltage_Range */ - -} FLASH_EraseInitTypeDef; - -/** - * @brief FLASH Option Bytes Program structure definition - */ -typedef struct -{ - uint32_t OptionType; /*!< Option byte to be configured. - This parameter can be a value of @ref FLASHEx_Option_Type */ - - uint32_t WRPState; /*!< Write protection activation or deactivation. - This parameter can be a value of @ref FLASHEx_WRP_State */ - - uint32_t WRPSector; /*!< Specifies the sector(s) to be write protected. - The value of this parameter depend on device used within the same series */ - - uint32_t Banks; /*!< Select banks for WRP activation/deactivation of all sectors. - This parameter must be a value of @ref FLASHEx_Banks */ - - uint32_t RDPLevel; /*!< Set the read protection level. - This parameter can be a value of @ref FLASHEx_Option_Bytes_Read_Protection */ - - uint32_t BORLevel; /*!< Set the BOR Level. - This parameter can be a value of @ref FLASHEx_BOR_Reset_Level */ - - uint8_t USERConfig; /*!< Program the FLASH User Option Byte: IWDG_SW / RST_STOP / RST_STDBY. */ - -} FLASH_OBProgramInitTypeDef; - -/** - * @brief FLASH Advanced Option Bytes Program structure definition - */ -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) ||\ - defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F469xx) ||\ - defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) ||\ - defined(STM32F412Cx) -typedef struct -{ - uint32_t OptionType; /*!< Option byte to be configured for extension. - This parameter can be a value of @ref FLASHEx_Advanced_Option_Type */ - - uint32_t PCROPState; /*!< PCROP activation or deactivation. - This parameter can be a value of @ref FLASHEx_PCROP_State */ - -#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F412Zx) ||\ - defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) - uint16_t Sectors; /*!< specifies the sector(s) set for PCROP. - This parameter can be a value of @ref FLASHEx_Option_Bytes_PC_ReadWrite_Protection */ -#endif /* STM32F401xC || STM32F401xE || STM32F410xx || STM32F411xE || STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx ||\ - STM32F412Cx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) - uint32_t Banks; /*!< Select banks for PCROP activation/deactivation of all sectors. - This parameter must be a value of @ref FLASHEx_Banks */ - - uint16_t SectorsBank1; /*!< Specifies the sector(s) set for PCROP for Bank1. - This parameter can be a value of @ref FLASHEx_Option_Bytes_PC_ReadWrite_Protection */ - - uint16_t SectorsBank2; /*!< Specifies the sector(s) set for PCROP for Bank2. - This parameter can be a value of @ref FLASHEx_Option_Bytes_PC_ReadWrite_Protection */ - - uint8_t BootConfig; /*!< Specifies Option bytes for boot config. - This parameter can be a value of @ref FLASHEx_Dual_Boot */ - -#endif /*STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ -} FLASH_AdvOBProgramInitTypeDef; -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F401xC || STM32F401xE || STM32F410xx || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ -/** - * @} - */ - -/* Exported constants --------------------------------------------------------*/ - -/** @defgroup FLASHEx_Exported_Constants FLASH Exported Constants - * @{ - */ - -/** @defgroup FLASHEx_Type_Erase FLASH Type Erase - * @{ - */ -#define FLASH_TYPEERASE_SECTORS ((uint32_t)0x00U) /*!< Sectors erase only */ -#define FLASH_TYPEERASE_MASSERASE ((uint32_t)0x01U) /*!< Flash Mass erase activation */ -/** - * @} - */ - -/** @defgroup FLASHEx_Voltage_Range FLASH Voltage Range - * @{ - */ -#define FLASH_VOLTAGE_RANGE_1 ((uint32_t)0x00U) /*!< Device operating range: 1.8V to 2.1V */ -#define FLASH_VOLTAGE_RANGE_2 ((uint32_t)0x01U) /*!< Device operating range: 2.1V to 2.7V */ -#define FLASH_VOLTAGE_RANGE_3 ((uint32_t)0x02U) /*!< Device operating range: 2.7V to 3.6V */ -#define FLASH_VOLTAGE_RANGE_4 ((uint32_t)0x03U) /*!< Device operating range: 2.7V to 3.6V + External Vpp */ -/** - * @} - */ - -/** @defgroup FLASHEx_WRP_State FLASH WRP State - * @{ - */ -#define OB_WRPSTATE_DISABLE ((uint32_t)0x00U) /*!< Disable the write protection of the desired bank 1 sectors */ -#define OB_WRPSTATE_ENABLE ((uint32_t)0x01U) /*!< Enable the write protection of the desired bank 1 sectors */ -/** - * @} - */ - -/** @defgroup FLASHEx_Option_Type FLASH Option Type - * @{ - */ -#define OPTIONBYTE_WRP ((uint32_t)0x01U) /*!< WRP option byte configuration */ -#define OPTIONBYTE_RDP ((uint32_t)0x02U) /*!< RDP option byte configuration */ -#define OPTIONBYTE_USER ((uint32_t)0x04U) /*!< USER option byte configuration */ -#define OPTIONBYTE_BOR ((uint32_t)0x08U) /*!< BOR option byte configuration */ -/** - * @} - */ - -/** @defgroup FLASHEx_Option_Bytes_Read_Protection FLASH Option Bytes Read Protection - * @{ - */ -#define OB_RDP_LEVEL_0 ((uint8_t)0xAAU) -#define OB_RDP_LEVEL_1 ((uint8_t)0x55U) -#define OB_RDP_LEVEL_2 ((uint8_t)0xCCU) /*!< Warning: When enabling read protection level 2 - it s no more possible to go back to level 1 or 0 */ -/** - * @} - */ - -/** @defgroup FLASHEx_Option_Bytes_IWatchdog FLASH Option Bytes IWatchdog - * @{ - */ -#define OB_IWDG_SW ((uint8_t)0x20U) /*!< Software IWDG selected */ -#define OB_IWDG_HW ((uint8_t)0x00U) /*!< Hardware IWDG selected */ -/** - * @} - */ - -/** @defgroup FLASHEx_Option_Bytes_nRST_STOP FLASH Option Bytes nRST_STOP - * @{ - */ -#define OB_STOP_NO_RST ((uint8_t)0x40U) /*!< No reset generated when entering in STOP */ -#define OB_STOP_RST ((uint8_t)0x00U) /*!< Reset generated when entering in STOP */ -/** - * @} - */ - - -/** @defgroup FLASHEx_Option_Bytes_nRST_STDBY FLASH Option Bytes nRST_STDBY - * @{ - */ -#define OB_STDBY_NO_RST ((uint8_t)0x80U) /*!< No reset generated when entering in STANDBY */ -#define OB_STDBY_RST ((uint8_t)0x00U) /*!< Reset generated when entering in STANDBY */ -/** - * @} - */ - -/** @defgroup FLASHEx_BOR_Reset_Level FLASH BOR Reset Level - * @{ - */ -#define OB_BOR_LEVEL3 ((uint8_t)0x00U) /*!< Supply voltage ranges from 2.70 to 3.60 V */ -#define OB_BOR_LEVEL2 ((uint8_t)0x04U) /*!< Supply voltage ranges from 2.40 to 2.70 V */ -#define OB_BOR_LEVEL1 ((uint8_t)0x08U) /*!< Supply voltage ranges from 2.10 to 2.40 V */ -#define OB_BOR_OFF ((uint8_t)0x0CU) /*!< Supply voltage ranges from 1.62 to 2.10 V */ -/** - * @} - */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) ||\ - defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F469xx) ||\ - defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) ||\ - defined(STM32F412Cx) -/** @defgroup FLASHEx_PCROP_State FLASH PCROP State - * @{ - */ -#define OB_PCROP_STATE_DISABLE ((uint32_t)0x00U) /*!< Disable PCROP */ -#define OB_PCROP_STATE_ENABLE ((uint32_t)0x01U) /*!< Enable PCROP */ -/** - * @} - */ -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F401xC || STM32F401xE ||\ - STM32F410xx || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx ||\ - STM32F412Vx) || defined(STM32F412Rx) ||\ - STM32F412Cx */ - -/** @defgroup FLASHEx_Advanced_Option_Type FLASH Advanced Option Type - * @{ - */ -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F469xx) || defined(STM32F479xx) -#define OPTIONBYTE_PCROP ((uint32_t)0x01U) /*!< PCROP option byte configuration */ -#define OPTIONBYTE_BOOTCONFIG ((uint32_t)0x02U) /*!< BOOTConfig option byte configuration */ -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) ||\ - defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F412Zx) ||\ - defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -#define OPTIONBYTE_PCROP ((uint32_t)0x01U) /*!= FLASH_BASE) && ((ADDRESS) <= FLASH_END)) -#define IS_FLASH_NBSECTORS(NBSECTORS) (((NBSECTORS) != 0) && ((NBSECTORS) <= FLASH_SECTOR_TOTAL)) - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) -#define IS_OB_WRP_SECTOR(SECTOR)((((SECTOR) & (uint32_t)0xFF000000U) == 0x00000000U) && ((SECTOR) != 0x00000000U)) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) -#define IS_OB_WRP_SECTOR(SECTOR)((((SECTOR) & (uint32_t)0xFFFFF000U) == 0x00000000U) && ((SECTOR) != 0x00000000U)) -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx */ - -#if defined(STM32F401xC) -#define IS_OB_WRP_SECTOR(SECTOR)((((SECTOR) & (uint32_t)0xFFFFF000U) == 0x00000000U) && ((SECTOR) != 0x00000000U)) -#endif /* STM32F401xC */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -#define IS_OB_WRP_SECTOR(SECTOR)((((SECTOR) & (uint32_t)0xFFFFF000U) == 0x00000000U) && ((SECTOR) != 0x00000000U)) -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -#if defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F412Zx) || defined(STM32F412Vx) ||\ - defined(STM32F412Rx) || defined(STM32F412Cx) -#define IS_OB_WRP_SECTOR(SECTOR)((((SECTOR) & (uint32_t)0xFFFFF000U) == 0x00000000U) && ((SECTOR) != 0x00000000U)) -#endif /* STM32F401xE || STM32F411xE || STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) -#define IS_OB_PCROP(SECTOR)((((SECTOR) & (uint32_t)0xFFFFF000U) == 0x00000000U) && ((SECTOR) != 0x00000000U)) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F401xC) -#define IS_OB_PCROP(SECTOR)((((SECTOR) & (uint32_t)0xFFFFF000U) == 0x00000000U) && ((SECTOR) != 0x00000000U)) -#endif /* STM32F401xC */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -#define IS_OB_PCROP(SECTOR)((((SECTOR) & (uint32_t)0xFFFFF000U) == 0x00000000U) && ((SECTOR) != 0x00000000U)) -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -#if defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F412Zx) || defined(STM32F412Vx) ||\ - defined(STM32F412Rx) || defined(STM32F412Cx) -#define IS_OB_PCROP(SECTOR)((((SECTOR) & (uint32_t)0xFFFFF000U) == 0x00000000U) && ((SECTOR) != 0x00000000U)) -#endif /* STM32F401xE || STM32F411xE || STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F469xx) || defined(STM32F479xx) -#define IS_OB_BOOT(BOOT) (((BOOT) == OB_DUAL_BOOT_ENABLE) || ((BOOT) == OB_DUAL_BOOT_DISABLE)) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) ||\ - defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F469xx) ||\ - defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) ||\ - defined(STM32F412Cx) -#define IS_OB_PCROP_SELECT(PCROP) (((PCROP) == OB_PCROP_SELECTED) || ((PCROP) == OB_PCROP_DESELECTED)) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F401xC || STM32F401xE ||\ - STM32F410xx || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx ||\ - STM32F412Vx || STM32F412Rx || STM32F412Cx */ -/** - * @} - */ - -/** - * @} - */ - -/* Private functions ---------------------------------------------------------*/ -/** @defgroup FLASHEx_Private_Functions FLASH Private Functions - * @{ - */ -void FLASH_Erase_Sector(uint32_t Sector, uint8_t VoltageRange); -void FLASH_FlushCaches(void); -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F4xx_HAL_FLASH_EX_H */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash_ramfunc.h b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash_ramfunc.h deleted file mode 100644 index de2c4aae..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash_ramfunc.h +++ /dev/null @@ -1,97 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_flash_ramfunc.h - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Header file of FLASH RAMFUNC driver. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_FLASH_RAMFUNC_H -#define __STM32F4xx_FLASH_RAMFUNC_H - -#ifdef __cplusplus -extern "C" { -#endif -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F412Zx) ||\ - defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_def.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @addtogroup FLASH_RAMFUNC - * @{ - */ - -/* Exported types ------------------------------------------------------------*/ -/* Exported macro ------------------------------------------------------------*/ -/* Exported functions --------------------------------------------------------*/ -/** @addtogroup FLASH_RAMFUNC_Exported_Functions - * @{ - */ - -/** @addtogroup FLASH_RAMFUNC_Exported_Functions_Group1 - * @{ - */ -__RAM_FUNC HAL_FLASHEx_StopFlashInterfaceClk(void); -__RAM_FUNC HAL_FLASHEx_StartFlashInterfaceClk(void); -__RAM_FUNC HAL_FLASHEx_EnableFlashSleepMode(void); -__RAM_FUNC HAL_FLASHEx_DisableFlashSleepMode(void); -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -#endif /* STM32F410xx || STM32F411xE || STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ -#ifdef __cplusplus -} -#endif - - -#endif /* __STM32F4xx_FLASH_RAMFUNC_H */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_gpio_ex.h b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_gpio_ex.h deleted file mode 100644 index 5c22c343..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_gpio_ex.h +++ /dev/null @@ -1,1452 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_gpio_ex.h - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Header file of GPIO HAL Extension module. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_GPIO_EX_H -#define __STM32F4xx_HAL_GPIO_EX_H - -#ifdef __cplusplus -extern "C" { -#endif - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_def.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @defgroup GPIOEx GPIOEx - * @{ - */ - -/* Exported types ------------------------------------------------------------*/ -/* Exported constants --------------------------------------------------------*/ -/** @defgroup GPIOEx_Exported_Constants GPIO Exported Constants - * @{ - */ - -/** @defgroup GPIO_Alternate_function_selection GPIO Alternate Function Selection - * @{ - */ - -/*------------------------------------------ STM32F429xx/STM32F439xx ---------*/ -#if defined(STM32F429xx) || defined(STM32F439xx) -/** - * @brief AF 0 selection - */ -#define GPIO_AF0_RTC_50Hz ((uint8_t)0x00U) /* RTC_50Hz Alternate Function mapping */ -#define GPIO_AF0_MCO ((uint8_t)0x00U) /* MCO (MCO1 and MCO2) Alternate Function mapping */ -#define GPIO_AF0_TAMPER ((uint8_t)0x00U) /* TAMPER (TAMPER_1 and TAMPER_2) Alternate Function mapping */ -#define GPIO_AF0_SWJ ((uint8_t)0x00U) /* SWJ (SWD and JTAG) Alternate Function mapping */ -#define GPIO_AF0_TRACE ((uint8_t)0x00U) /* TRACE Alternate Function mapping */ - -/** - * @brief AF 1 selection - */ -#define GPIO_AF1_TIM1 ((uint8_t)0x01U) /* TIM1 Alternate Function mapping */ -#define GPIO_AF1_TIM2 ((uint8_t)0x01U) /* TIM2 Alternate Function mapping */ - -/** - * @brief AF 2 selection - */ -#define GPIO_AF2_TIM3 ((uint8_t)0x02U) /* TIM3 Alternate Function mapping */ -#define GPIO_AF2_TIM4 ((uint8_t)0x02U) /* TIM4 Alternate Function mapping */ -#define GPIO_AF2_TIM5 ((uint8_t)0x02U) /* TIM5 Alternate Function mapping */ - -/** - * @brief AF 3 selection - */ -#define GPIO_AF3_TIM8 ((uint8_t)0x03U) /* TIM8 Alternate Function mapping */ -#define GPIO_AF3_TIM9 ((uint8_t)0x03U) /* TIM9 Alternate Function mapping */ -#define GPIO_AF3_TIM10 ((uint8_t)0x03U) /* TIM10 Alternate Function mapping */ -#define GPIO_AF3_TIM11 ((uint8_t)0x03U) /* TIM11 Alternate Function mapping */ - -/** - * @brief AF 4 selection - */ -#define GPIO_AF4_I2C1 ((uint8_t)0x04U) /* I2C1 Alternate Function mapping */ -#define GPIO_AF4_I2C2 ((uint8_t)0x04U) /* I2C2 Alternate Function mapping */ -#define GPIO_AF4_I2C3 ((uint8_t)0x04U) /* I2C3 Alternate Function mapping */ - -/** - * @brief AF 5 selection - */ -#define GPIO_AF5_SPI1 ((uint8_t)0x05U) /* SPI1 Alternate Function mapping */ -#define GPIO_AF5_SPI2 ((uint8_t)0x05U) /* SPI2/I2S2 Alternate Function mapping */ -#define GPIO_AF5_SPI3 ((uint8_t)0x05U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF5_SPI4 ((uint8_t)0x05U) /* SPI4 Alternate Function mapping */ -#define GPIO_AF5_SPI5 ((uint8_t)0x05U) /* SPI5 Alternate Function mapping */ -#define GPIO_AF5_SPI6 ((uint8_t)0x05U) /* SPI6 Alternate Function mapping */ -#define GPIO_AF5_I2S3ext ((uint8_t)0x05U) /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 6 selection - */ -#define GPIO_AF6_SPI3 ((uint8_t)0x06U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF6_I2S2ext ((uint8_t)0x06U) /* I2S2ext_SD Alternate Function mapping */ -#define GPIO_AF6_SAI1 ((uint8_t)0x06U) /* SAI1 Alternate Function mapping */ - -/** - * @brief AF 7 selection - */ -#define GPIO_AF7_USART1 ((uint8_t)0x07U) /* USART1 Alternate Function mapping */ -#define GPIO_AF7_USART2 ((uint8_t)0x07U) /* USART2 Alternate Function mapping */ -#define GPIO_AF7_USART3 ((uint8_t)0x07U) /* USART3 Alternate Function mapping */ -#define GPIO_AF7_I2S3ext ((uint8_t)0x07U) /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 8 selection - */ -#define GPIO_AF8_UART4 ((uint8_t)0x08U) /* UART4 Alternate Function mapping */ -#define GPIO_AF8_UART5 ((uint8_t)0x08U) /* UART5 Alternate Function mapping */ -#define GPIO_AF8_USART6 ((uint8_t)0x08U) /* USART6 Alternate Function mapping */ -#define GPIO_AF8_UART7 ((uint8_t)0x08U) /* UART7 Alternate Function mapping */ -#define GPIO_AF8_UART8 ((uint8_t)0x08U) /* UART8 Alternate Function mapping */ - -/** - * @brief AF 9 selection - */ -#define GPIO_AF9_CAN1 ((uint8_t)0x09U) /* CAN1 Alternate Function mapping */ -#define GPIO_AF9_CAN2 ((uint8_t)0x09U) /* CAN2 Alternate Function mapping */ -#define GPIO_AF9_TIM12 ((uint8_t)0x09U) /* TIM12 Alternate Function mapping */ -#define GPIO_AF9_TIM13 ((uint8_t)0x09U) /* TIM13 Alternate Function mapping */ -#define GPIO_AF9_TIM14 ((uint8_t)0x09U) /* TIM14 Alternate Function mapping */ -#define GPIO_AF9_LTDC ((uint8_t)0x09U) /* LCD-TFT Alternate Function mapping */ - -/** - * @brief AF 10 selection - */ -#define GPIO_AF10_OTG_FS ((uint8_t)0x0AU) /* OTG_FS Alternate Function mapping */ -#define GPIO_AF10_OTG_HS ((uint8_t)0x0AU) /* OTG_HS Alternate Function mapping */ - -/** - * @brief AF 11 selection - */ -#define GPIO_AF11_ETH ((uint8_t)0x0BU) /* ETHERNET Alternate Function mapping */ - -/** - * @brief AF 12 selection - */ -#define GPIO_AF12_FMC ((uint8_t)0x0CU) /* FMC Alternate Function mapping */ -#define GPIO_AF12_OTG_HS_FS ((uint8_t)0x0CU) /* OTG HS configured in FS, Alternate Function mapping */ -#define GPIO_AF12_SDIO ((uint8_t)0x0CU) /* SDIO Alternate Function mapping */ - -/** - * @brief AF 13 selection - */ -#define GPIO_AF13_DCMI ((uint8_t)0x0DU) /* DCMI Alternate Function mapping */ - -/** - * @brief AF 14 selection - */ -#define GPIO_AF14_LTDC ((uint8_t)0x0EU) /* LCD-TFT Alternate Function mapping */ - -/** - * @brief AF 15 selection - */ -#define GPIO_AF15_EVENTOUT ((uint8_t)0x0FU) /* EVENTOUT Alternate Function mapping */ -#endif /* STM32F429xx || STM32F439xx */ -/*----------------------------------------------------------------------------*/ - -/*---------------------------------- STM32F427xx/STM32F437xx------------------*/ -#if defined(STM32F427xx) || defined(STM32F437xx) -/** - * @brief AF 0 selection - */ -#define GPIO_AF0_RTC_50Hz ((uint8_t)0x00U) /* RTC_50Hz Alternate Function mapping */ -#define GPIO_AF0_MCO ((uint8_t)0x00U) /* MCO (MCO1 and MCO2) Alternate Function mapping */ -#define GPIO_AF0_TAMPER ((uint8_t)0x00U) /* TAMPER (TAMPER_1 and TAMPER_2) Alternate Function mapping */ -#define GPIO_AF0_SWJ ((uint8_t)0x00U) /* SWJ (SWD and JTAG) Alternate Function mapping */ -#define GPIO_AF0_TRACE ((uint8_t)0x00U) /* TRACE Alternate Function mapping */ - -/** - * @brief AF 1 selection - */ -#define GPIO_AF1_TIM1 ((uint8_t)0x01U) /* TIM1 Alternate Function mapping */ -#define GPIO_AF1_TIM2 ((uint8_t)0x01U) /* TIM2 Alternate Function mapping */ - -/** - * @brief AF 2 selection - */ -#define GPIO_AF2_TIM3 ((uint8_t)0x02U) /* TIM3 Alternate Function mapping */ -#define GPIO_AF2_TIM4 ((uint8_t)0x02U) /* TIM4 Alternate Function mapping */ -#define GPIO_AF2_TIM5 ((uint8_t)0x02U) /* TIM5 Alternate Function mapping */ - -/** - * @brief AF 3 selection - */ -#define GPIO_AF3_TIM8 ((uint8_t)0x03U) /* TIM8 Alternate Function mapping */ -#define GPIO_AF3_TIM9 ((uint8_t)0x03U) /* TIM9 Alternate Function mapping */ -#define GPIO_AF3_TIM10 ((uint8_t)0x03U) /* TIM10 Alternate Function mapping */ -#define GPIO_AF3_TIM11 ((uint8_t)0x03U) /* TIM11 Alternate Function mapping */ - -/** - * @brief AF 4 selection - */ -#define GPIO_AF4_I2C1 ((uint8_t)0x04U) /* I2C1 Alternate Function mapping */ -#define GPIO_AF4_I2C2 ((uint8_t)0x04U) /* I2C2 Alternate Function mapping */ -#define GPIO_AF4_I2C3 ((uint8_t)0x04U) /* I2C3 Alternate Function mapping */ - -/** - * @brief AF 5 selection - */ -#define GPIO_AF5_SPI1 ((uint8_t)0x05U) /* SPI1 Alternate Function mapping */ -#define GPIO_AF5_SPI2 ((uint8_t)0x05U) /* SPI2/I2S2 Alternate Function mapping */ -#define GPIO_AF5_SPI3 ((uint8_t)0x05U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF5_SPI4 ((uint8_t)0x05U) /* SPI4 Alternate Function mapping */ -#define GPIO_AF5_SPI5 ((uint8_t)0x05U) /* SPI5 Alternate Function mapping */ -#define GPIO_AF5_SPI6 ((uint8_t)0x05U) /* SPI6 Alternate Function mapping */ -/** @brief GPIO_Legacy - */ -#define GPIO_AF5_I2S3ext GPIO_AF5_SPI3 /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 6 selection - */ -#define GPIO_AF6_SPI3 ((uint8_t)0x06U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF6_I2S2ext ((uint8_t)0x06U) /* I2S2ext_SD Alternate Function mapping */ -#define GPIO_AF6_SAI1 ((uint8_t)0x06U) /* SAI1 Alternate Function mapping */ - -/** - * @brief AF 7 selection - */ -#define GPIO_AF7_USART1 ((uint8_t)0x07U) /* USART1 Alternate Function mapping */ -#define GPIO_AF7_USART2 ((uint8_t)0x07U) /* USART2 Alternate Function mapping */ -#define GPIO_AF7_USART3 ((uint8_t)0x07U) /* USART3 Alternate Function mapping */ -#define GPIO_AF7_I2S3ext ((uint8_t)0x07U) /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 8 selection - */ -#define GPIO_AF8_UART4 ((uint8_t)0x08U) /* UART4 Alternate Function mapping */ -#define GPIO_AF8_UART5 ((uint8_t)0x08U) /* UART5 Alternate Function mapping */ -#define GPIO_AF8_USART6 ((uint8_t)0x08U) /* USART6 Alternate Function mapping */ -#define GPIO_AF8_UART7 ((uint8_t)0x08U) /* UART7 Alternate Function mapping */ -#define GPIO_AF8_UART8 ((uint8_t)0x08U) /* UART8 Alternate Function mapping */ - -/** - * @brief AF 9 selection - */ -#define GPIO_AF9_CAN1 ((uint8_t)0x09U) /* CAN1 Alternate Function mapping */ -#define GPIO_AF9_CAN2 ((uint8_t)0x09U) /* CAN2 Alternate Function mapping */ -#define GPIO_AF9_TIM12 ((uint8_t)0x09U) /* TIM12 Alternate Function mapping */ -#define GPIO_AF9_TIM13 ((uint8_t)0x09U) /* TIM13 Alternate Function mapping */ -#define GPIO_AF9_TIM14 ((uint8_t)0x09U) /* TIM14 Alternate Function mapping */ - -/** - * @brief AF 10 selection - */ -#define GPIO_AF10_OTG_FS ((uint8_t)0x0AU) /* OTG_FS Alternate Function mapping */ -#define GPIO_AF10_OTG_HS ((uint8_t)0x0AU) /* OTG_HS Alternate Function mapping */ - -/** - * @brief AF 11 selection - */ -#define GPIO_AF11_ETH ((uint8_t)0x0BU) /* ETHERNET Alternate Function mapping */ - -/** - * @brief AF 12 selection - */ -#define GPIO_AF12_FMC ((uint8_t)0x0CU) /* FMC Alternate Function mapping */ -#define GPIO_AF12_OTG_HS_FS ((uint8_t)0x0CU) /* OTG HS configured in FS, Alternate Function mapping */ -#define GPIO_AF12_SDIO ((uint8_t)0x0CU) /* SDIO Alternate Function mapping */ - -/** - * @brief AF 13 selection - */ -#define GPIO_AF13_DCMI ((uint8_t)0x0DU) /* DCMI Alternate Function mapping */ - -/** - * @brief AF 15 selection - */ -#define GPIO_AF15_EVENTOUT ((uint8_t)0x0FU) /* EVENTOUT Alternate Function mapping */ -#endif /* STM32F427xx || STM32F437xx */ -/*----------------------------------------------------------------------------*/ - -/*---------------------------------- STM32F407xx/STM32F417xx------------------*/ -#if defined(STM32F407xx) || defined(STM32F417xx) -/** - * @brief AF 0 selection - */ -#define GPIO_AF0_RTC_50Hz ((uint8_t)0x00U) /* RTC_50Hz Alternate Function mapping */ -#define GPIO_AF0_MCO ((uint8_t)0x00U) /* MCO (MCO1 and MCO2) Alternate Function mapping */ -#define GPIO_AF0_TAMPER ((uint8_t)0x00U) /* TAMPER (TAMPER_1 and TAMPER_2) Alternate Function mapping */ -#define GPIO_AF0_SWJ ((uint8_t)0x00U) /* SWJ (SWD and JTAG) Alternate Function mapping */ -#define GPIO_AF0_TRACE ((uint8_t)0x00U) /* TRACE Alternate Function mapping */ - -/** - * @brief AF 1 selection - */ -#define GPIO_AF1_TIM1 ((uint8_t)0x01U) /* TIM1 Alternate Function mapping */ -#define GPIO_AF1_TIM2 ((uint8_t)0x01U) /* TIM2 Alternate Function mapping */ - -/** - * @brief AF 2 selection - */ -#define GPIO_AF2_TIM3 ((uint8_t)0x02U) /* TIM3 Alternate Function mapping */ -#define GPIO_AF2_TIM4 ((uint8_t)0x02U) /* TIM4 Alternate Function mapping */ -#define GPIO_AF2_TIM5 ((uint8_t)0x02U) /* TIM5 Alternate Function mapping */ - -/** - * @brief AF 3 selection - */ -#define GPIO_AF3_TIM8 ((uint8_t)0x03U) /* TIM8 Alternate Function mapping */ -#define GPIO_AF3_TIM9 ((uint8_t)0x03U) /* TIM9 Alternate Function mapping */ -#define GPIO_AF3_TIM10 ((uint8_t)0x03U) /* TIM10 Alternate Function mapping */ -#define GPIO_AF3_TIM11 ((uint8_t)0x03U) /* TIM11 Alternate Function mapping */ - -/** - * @brief AF 4 selection - */ -#define GPIO_AF4_I2C1 ((uint8_t)0x04U) /* I2C1 Alternate Function mapping */ -#define GPIO_AF4_I2C2 ((uint8_t)0x04U) /* I2C2 Alternate Function mapping */ -#define GPIO_AF4_I2C3 ((uint8_t)0x04U) /* I2C3 Alternate Function mapping */ - -/** - * @brief AF 5 selection - */ -#define GPIO_AF5_SPI1 ((uint8_t)0x05U) /* SPI1 Alternate Function mapping */ -#define GPIO_AF5_SPI2 ((uint8_t)0x05U) /* SPI2/I2S2 Alternate Function mapping */ -#define GPIO_AF5_I2S3ext ((uint8_t)0x05U) /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 6 selection - */ -#define GPIO_AF6_SPI3 ((uint8_t)0x06U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF6_I2S2ext ((uint8_t)0x06U) /* I2S2ext_SD Alternate Function mapping */ - -/** - * @brief AF 7 selection - */ -#define GPIO_AF7_USART1 ((uint8_t)0x07U) /* USART1 Alternate Function mapping */ -#define GPIO_AF7_USART2 ((uint8_t)0x07U) /* USART2 Alternate Function mapping */ -#define GPIO_AF7_USART3 ((uint8_t)0x07U) /* USART3 Alternate Function mapping */ -#define GPIO_AF7_I2S3ext ((uint8_t)0x07U) /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 8 selection - */ -#define GPIO_AF8_UART4 ((uint8_t)0x08U) /* UART4 Alternate Function mapping */ -#define GPIO_AF8_UART5 ((uint8_t)0x08U) /* UART5 Alternate Function mapping */ -#define GPIO_AF8_USART6 ((uint8_t)0x08U) /* USART6 Alternate Function mapping */ - -/** - * @brief AF 9 selection - */ -#define GPIO_AF9_CAN1 ((uint8_t)0x09U) /* CAN1 Alternate Function mapping */ -#define GPIO_AF9_CAN2 ((uint8_t)0x09U) /* CAN2 Alternate Function mapping */ -#define GPIO_AF9_TIM12 ((uint8_t)0x09U) /* TIM12 Alternate Function mapping */ -#define GPIO_AF9_TIM13 ((uint8_t)0x09U) /* TIM13 Alternate Function mapping */ -#define GPIO_AF9_TIM14 ((uint8_t)0x09U) /* TIM14 Alternate Function mapping */ - -/** - * @brief AF 10 selection - */ -#define GPIO_AF10_OTG_FS ((uint8_t)0x0AU) /* OTG_FS Alternate Function mapping */ -#define GPIO_AF10_OTG_HS ((uint8_t)0x0AU) /* OTG_HS Alternate Function mapping */ - -/** - * @brief AF 11 selection - */ -#define GPIO_AF11_ETH ((uint8_t)0x0BU) /* ETHERNET Alternate Function mapping */ - -/** - * @brief AF 12 selection - */ -#define GPIO_AF12_FSMC ((uint8_t)0x0CU) /* FSMC Alternate Function mapping */ -#define GPIO_AF12_OTG_HS_FS ((uint8_t)0x0CU) /* OTG HS configured in FS, Alternate Function mapping */ -#define GPIO_AF12_SDIO ((uint8_t)0x0CU) /* SDIO Alternate Function mapping */ - -/** - * @brief AF 13 selection - */ -#define GPIO_AF13_DCMI ((uint8_t)0x0DU) /* DCMI Alternate Function mapping */ - -/** - * @brief AF 15 selection - */ -#define GPIO_AF15_EVENTOUT ((uint8_t)0x0FU) /* EVENTOUT Alternate Function mapping */ -#endif /* STM32F407xx || STM32F417xx */ -/*----------------------------------------------------------------------------*/ - -/*---------------------------------- STM32F405xx/STM32F415xx------------------*/ -#if defined(STM32F405xx) || defined(STM32F415xx) -/** - * @brief AF 0 selection - */ -#define GPIO_AF0_RTC_50Hz ((uint8_t)0x00U) /* RTC_50Hz Alternate Function mapping */ -#define GPIO_AF0_MCO ((uint8_t)0x00U) /* MCO (MCO1 and MCO2) Alternate Function mapping */ -#define GPIO_AF0_TAMPER ((uint8_t)0x00U) /* TAMPER (TAMPER_1 and TAMPER_2) Alternate Function mapping */ -#define GPIO_AF0_SWJ ((uint8_t)0x00U) /* SWJ (SWD and JTAG) Alternate Function mapping */ -#define GPIO_AF0_TRACE ((uint8_t)0x00U) /* TRACE Alternate Function mapping */ - -/** - * @brief AF 1 selection - */ -#define GPIO_AF1_TIM1 ((uint8_t)0x01U) /* TIM1 Alternate Function mapping */ -#define GPIO_AF1_TIM2 ((uint8_t)0x01U) /* TIM2 Alternate Function mapping */ - -/** - * @brief AF 2 selection - */ -#define GPIO_AF2_TIM3 ((uint8_t)0x02U) /* TIM3 Alternate Function mapping */ -#define GPIO_AF2_TIM4 ((uint8_t)0x02U) /* TIM4 Alternate Function mapping */ -#define GPIO_AF2_TIM5 ((uint8_t)0x02U) /* TIM5 Alternate Function mapping */ - -/** - * @brief AF 3 selection - */ -#define GPIO_AF3_TIM8 ((uint8_t)0x03U) /* TIM8 Alternate Function mapping */ -#define GPIO_AF3_TIM9 ((uint8_t)0x03U) /* TIM9 Alternate Function mapping */ -#define GPIO_AF3_TIM10 ((uint8_t)0x03U) /* TIM10 Alternate Function mapping */ -#define GPIO_AF3_TIM11 ((uint8_t)0x03U) /* TIM11 Alternate Function mapping */ - -/** - * @brief AF 4 selection - */ -#define GPIO_AF4_I2C1 ((uint8_t)0x04U) /* I2C1 Alternate Function mapping */ -#define GPIO_AF4_I2C2 ((uint8_t)0x04U) /* I2C2 Alternate Function mapping */ -#define GPIO_AF4_I2C3 ((uint8_t)0x04U) /* I2C3 Alternate Function mapping */ - -/** - * @brief AF 5 selection - */ -#define GPIO_AF5_SPI1 ((uint8_t)0x05U) /* SPI1 Alternate Function mapping */ -#define GPIO_AF5_SPI2 ((uint8_t)0x05U) /* SPI2/I2S2 Alternate Function mapping */ -#define GPIO_AF5_I2S3ext ((uint8_t)0x05U) /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 6 selection - */ -#define GPIO_AF6_SPI3 ((uint8_t)0x06U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF6_I2S2ext ((uint8_t)0x06U) /* I2S2ext_SD Alternate Function mapping */ - -/** - * @brief AF 7 selection - */ -#define GPIO_AF7_USART1 ((uint8_t)0x07U) /* USART1 Alternate Function mapping */ -#define GPIO_AF7_USART2 ((uint8_t)0x07U) /* USART2 Alternate Function mapping */ -#define GPIO_AF7_USART3 ((uint8_t)0x07U) /* USART3 Alternate Function mapping */ -#define GPIO_AF7_I2S3ext ((uint8_t)0x07U) /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 8 selection - */ -#define GPIO_AF8_UART4 ((uint8_t)0x08U) /* UART4 Alternate Function mapping */ -#define GPIO_AF8_UART5 ((uint8_t)0x08U) /* UART5 Alternate Function mapping */ -#define GPIO_AF8_USART6 ((uint8_t)0x08U) /* USART6 Alternate Function mapping */ - -/** - * @brief AF 9 selection - */ -#define GPIO_AF9_CAN1 ((uint8_t)0x09U) /* CAN1 Alternate Function mapping */ -#define GPIO_AF9_CAN2 ((uint8_t)0x09U) /* CAN2 Alternate Function mapping */ -#define GPIO_AF9_TIM12 ((uint8_t)0x09U) /* TIM12 Alternate Function mapping */ -#define GPIO_AF9_TIM13 ((uint8_t)0x09U) /* TIM13 Alternate Function mapping */ -#define GPIO_AF9_TIM14 ((uint8_t)0x09U) /* TIM14 Alternate Function mapping */ - -/** - * @brief AF 10 selection - */ -#define GPIO_AF10_OTG_FS ((uint8_t)0x0AU) /* OTG_FS Alternate Function mapping */ -#define GPIO_AF10_OTG_HS ((uint8_t)0x0AU) /* OTG_HS Alternate Function mapping */ - -/** - * @brief AF 12 selection - */ -#define GPIO_AF12_FSMC ((uint8_t)0x0CU) /* FSMC Alternate Function mapping */ -#define GPIO_AF12_OTG_HS_FS ((uint8_t)0x0CU) /* OTG HS configured in FS, Alternate Function mapping */ -#define GPIO_AF12_SDIO ((uint8_t)0x0CU) /* SDIO Alternate Function mapping */ - -/** - * @brief AF 15 selection - */ -#define GPIO_AF15_EVENTOUT ((uint8_t)0x0FU) /* EVENTOUT Alternate Function mapping */ -#endif /* STM32F405xx || STM32F415xx */ - -/*----------------------------------------------------------------------------*/ - -/*---------------------------------------- STM32F401xx------------------------*/ -#if defined(STM32F401xC) || defined(STM32F401xE) -/** - * @brief AF 0 selection - */ -#define GPIO_AF0_RTC_50Hz ((uint8_t)0x00U) /* RTC_50Hz Alternate Function mapping */ -#define GPIO_AF0_MCO ((uint8_t)0x00U) /* MCO (MCO1 and MCO2) Alternate Function mapping */ -#define GPIO_AF0_TAMPER ((uint8_t)0x00U) /* TAMPER (TAMPER_1 and TAMPER_2) Alternate Function mapping */ -#define GPIO_AF0_SWJ ((uint8_t)0x00U) /* SWJ (SWD and JTAG) Alternate Function mapping */ -#define GPIO_AF0_TRACE ((uint8_t)0x00U) /* TRACE Alternate Function mapping */ - -/** - * @brief AF 1 selection - */ -#define GPIO_AF1_TIM1 ((uint8_t)0x01U) /* TIM1 Alternate Function mapping */ -#define GPIO_AF1_TIM2 ((uint8_t)0x01U) /* TIM2 Alternate Function mapping */ - -/** - * @brief AF 2 selection - */ -#define GPIO_AF2_TIM3 ((uint8_t)0x02U) /* TIM3 Alternate Function mapping */ -#define GPIO_AF2_TIM4 ((uint8_t)0x02U) /* TIM4 Alternate Function mapping */ -#define GPIO_AF2_TIM5 ((uint8_t)0x02U) /* TIM5 Alternate Function mapping */ - -/** - * @brief AF 3 selection - */ -#define GPIO_AF3_TIM9 ((uint8_t)0x03U) /* TIM9 Alternate Function mapping */ -#define GPIO_AF3_TIM10 ((uint8_t)0x03U) /* TIM10 Alternate Function mapping */ -#define GPIO_AF3_TIM11 ((uint8_t)0x03U) /* TIM11 Alternate Function mapping */ - -/** - * @brief AF 4 selection - */ -#define GPIO_AF4_I2C1 ((uint8_t)0x04U) /* I2C1 Alternate Function mapping */ -#define GPIO_AF4_I2C2 ((uint8_t)0x04U) /* I2C2 Alternate Function mapping */ -#define GPIO_AF4_I2C3 ((uint8_t)0x04U) /* I2C3 Alternate Function mapping */ - -/** - * @brief AF 5 selection - */ -#define GPIO_AF5_SPI1 ((uint8_t)0x05U) /* SPI1 Alternate Function mapping */ -#define GPIO_AF5_SPI2 ((uint8_t)0x05U) /* SPI2/I2S2 Alternate Function mapping */ -#define GPIO_AF5_SPI4 ((uint8_t)0x05U) /* SPI4 Alternate Function mapping */ -#define GPIO_AF5_I2S3ext ((uint8_t)0x05U) /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 6 selection - */ -#define GPIO_AF6_SPI3 ((uint8_t)0x06U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF6_I2S2ext ((uint8_t)0x06U) /* I2S2ext_SD Alternate Function mapping */ - -/** - * @brief AF 7 selection - */ -#define GPIO_AF7_USART1 ((uint8_t)0x07U) /* USART1 Alternate Function mapping */ -#define GPIO_AF7_USART2 ((uint8_t)0x07U) /* USART2 Alternate Function mapping */ -#define GPIO_AF7_I2S3ext ((uint8_t)0x07U) /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 8 selection - */ -#define GPIO_AF8_USART6 ((uint8_t)0x08U) /* USART6 Alternate Function mapping */ - -/** - * @brief AF 9 selection - */ -#define GPIO_AF9_TIM14 ((uint8_t)0x09U) /* TIM14 Alternate Function mapping */ -#define GPIO_AF9_I2C2 ((uint8_t)0x09U) /* I2C2 Alternate Function mapping */ -#define GPIO_AF9_I2C3 ((uint8_t)0x09U) /* I2C3 Alternate Function mapping */ - - -/** - * @brief AF 10 selection - */ -#define GPIO_AF10_OTG_FS ((uint8_t)0x0AU) /* OTG_FS Alternate Function mapping */ - -/** - * @brief AF 12 selection - */ -#define GPIO_AF12_SDIO ((uint8_t)0x0CU) /* SDIO Alternate Function mapping */ - -/** - * @brief AF 15 selection - */ -#define GPIO_AF15_EVENTOUT ((uint8_t)0x0FU) /* EVENTOUT Alternate Function mapping */ -#endif /* STM32F401xC || STM32F401xE */ -/*----------------------------------------------------------------------------*/ - -/*--------------- STM32F412Zx/STM32F412Vx/STM32F412Rx/STM32F412Cx-------------*/ -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -/** - * @brief AF 0 selection - */ -#define GPIO_AF0_RTC_50Hz ((uint8_t)0x00U) /* RTC_50Hz Alternate Function mapping */ -#define GPIO_AF0_MCO ((uint8_t)0x00U) /* MCO (MCO1 and MCO2) Alternate Function mapping */ -#define GPIO_AF0_TAMPER ((uint8_t)0x00U) /* TAMPER (TAMPER_1 and TAMPER_2) Alternate Function mapping */ -#define GPIO_AF0_SWJ ((uint8_t)0x00U) /* SWJ (SWD and JTAG) Alternate Function mapping */ -#define GPIO_AF0_TRACE ((uint8_t)0x00U) /* TRACE Alternate Function mapping */ - -/** - * @brief AF 1 selection - */ -#define GPIO_AF1_TIM1 ((uint8_t)0x01U) /* TIM1 Alternate Function mapping */ -#define GPIO_AF1_TIM2 ((uint8_t)0x01U) /* TIM2 Alternate Function mapping */ - -/** - * @brief AF 2 selection - */ -#define GPIO_AF2_TIM3 ((uint8_t)0x02U) /* TIM3 Alternate Function mapping */ -#define GPIO_AF2_TIM4 ((uint8_t)0x02U) /* TIM4 Alternate Function mapping */ -#define GPIO_AF2_TIM5 ((uint8_t)0x02U) /* TIM5 Alternate Function mapping */ - -/** - * @brief AF 3 selection - */ -#define GPIO_AF3_TIM8 ((uint8_t)0x03U) /* TIM8 Alternate Function mapping */ -#define GPIO_AF3_TIM9 ((uint8_t)0x03U) /* TIM9 Alternate Function mapping */ -#define GPIO_AF3_TIM10 ((uint8_t)0x03U) /* TIM10 Alternate Function mapping */ -#define GPIO_AF3_TIM11 ((uint8_t)0x03U) /* TIM11 Alternate Function mapping */ - -/** - * @brief AF 4 selection - */ -#define GPIO_AF4_I2C1 ((uint8_t)0x04U) /* I2C1 Alternate Function mapping */ -#define GPIO_AF4_I2C2 ((uint8_t)0x04U) /* I2C2 Alternate Function mapping */ -#define GPIO_AF4_I2C3 ((uint8_t)0x04U) /* I2C3 Alternate Function mapping */ -#define GPIO_AF4_FMPI2C1 ((uint8_t)0x04U) /* FMPI2C1 Alternate Function mapping */ - -/** - * @brief AF 5 selection - */ -#define GPIO_AF5_SPI1 ((uint8_t)0x05U) /* SPI1/I2S1 Alternate Function mapping */ -#define GPIO_AF5_SPI2 ((uint8_t)0x05U) /* SPI2/I2S2 Alternate Function mapping */ -#define GPIO_AF5_SPI3 ((uint8_t)0x05U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF5_SPI4 ((uint8_t)0x05U) /* SPI4/I2S4 Alternate Function mapping */ -#define GPIO_AF5_I2S3ext ((uint8_t)0x05U) /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 6 selection - */ -#define GPIO_AF6_SPI2 ((uint8_t)0x06U) /* I2S2 Alternate Function mapping */ -#define GPIO_AF6_SPI3 ((uint8_t)0x06U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF6_SPI4 ((uint8_t)0x06U) /* SPI4/I2S4 Alternate Function mapping */ -#define GPIO_AF6_SPI5 ((uint8_t)0x06U) /* SPI5/I2S5 Alternate Function mapping */ -#define GPIO_AF6_I2S2ext ((uint8_t)0x06U) /* I2S2ext_SD Alternate Function mapping */ -#define GPIO_AF6_DFSDM1 ((uint8_t)0x06U) /* DFSDM1 Alternate Function mapping */ -/** - * @brief AF 7 selection - */ -#define GPIO_AF7_SPI3 ((uint8_t)0x07U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF7_USART1 ((uint8_t)0x07U) /* USART1 Alternate Function mapping */ -#define GPIO_AF7_USART2 ((uint8_t)0x07U) /* USART2 Alternate Function mapping */ -#define GPIO_AF7_USART3 ((uint8_t)0x07U) /* USART3 Alternate Function mapping */ -#define GPIO_AF7_I2S3ext ((uint8_t)0x07U) /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 8 selection - */ -#define GPIO_AF8_USART6 ((uint8_t)0x08U) /* USART6 Alternate Function mapping */ -#define GPIO_AF8_USART3 ((uint8_t)0x08U) /* USART3 Alternate Function mapping */ -#define GPIO_AF8_DFSDM1 ((uint8_t)0x08U) /* DFSDM1 Alternate Function mapping */ -#define GPIO_AF8_CAN1 ((uint8_t)0x08U) /* CAN1 Alternate Function mapping */ - -/** - * @brief AF 9 selection - */ -#define GPIO_AF9_TIM13 ((uint8_t)0x09U) /* TIM13 Alternate Function mapping */ -#define GPIO_AF9_TIM14 ((uint8_t)0x09U) /* TIM14 Alternate Function mapping */ -#define GPIO_AF9_I2C2 ((uint8_t)0x09U) /* I2C2 Alternate Function mapping */ -#define GPIO_AF9_I2C3 ((uint8_t)0x09U) /* I2C3 Alternate Function mapping */ -#define GPIO_AF9_FMPI2C1 ((uint8_t)0x09U) /* FMPI2C1 Alternate Function mapping */ -#define GPIO_AF9_CAN1 ((uint8_t)0x09U) /* CAN1 Alternate Function mapping */ -#define GPIO_AF9_CAN2 ((uint8_t)0x09U) /* CAN1 Alternate Function mapping */ -#define GPIO_AF9_QSPI ((uint8_t)0x09U) /* QSPI Alternate Function mapping */ - -/** - * @brief AF 10 selection - */ -#define GPIO_AF10_OTG_FS ((uint8_t)0x0AU) /* OTG_FS Alternate Function mapping */ -#define GPIO_AF10_DFSDM1 ((uint8_t)0x0AU) /* DFSDM1 Alternate Function mapping */ -#define GPIO_AF10_QSPI ((uint8_t)0x0AU) /* QSPI Alternate Function mapping */ -#define GPIO_AF10_FMC ((uint8_t)0x0AU) /* FMC Alternate Function mapping */ - -/** - * @brief AF 12 selection - */ -#define GPIO_AF12_SDIO ((uint8_t)0x0CU) /* SDIO Alternate Function mapping */ -#define GPIO_AF12_FSMC ((uint8_t)0x0CU) /* FMC Alternate Function mapping */ - -/** - * @brief AF 15 selection - */ -#define GPIO_AF15_EVENTOUT ((uint8_t)0x0FU) /* EVENTOUT Alternate Function mapping */ -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ -/*---------------------------------------- STM32F411xx------------------------*/ -#if defined(STM32F411xE) -/** - * @brief AF 0 selection - */ -#define GPIO_AF0_RTC_50Hz ((uint8_t)0x00U) /* RTC_50Hz Alternate Function mapping */ -#define GPIO_AF0_MCO ((uint8_t)0x00U) /* MCO (MCO1 and MCO2) Alternate Function mapping */ -#define GPIO_AF0_TAMPER ((uint8_t)0x00U) /* TAMPER (TAMPER_1 and TAMPER_2) Alternate Function mapping */ -#define GPIO_AF0_SWJ ((uint8_t)0x00U) /* SWJ (SWD and JTAG) Alternate Function mapping */ -#define GPIO_AF0_TRACE ((uint8_t)0x00U) /* TRACE Alternate Function mapping */ - -/** - * @brief AF 1 selection - */ -#define GPIO_AF1_TIM1 ((uint8_t)0x01U) /* TIM1 Alternate Function mapping */ -#define GPIO_AF1_TIM2 ((uint8_t)0x01U) /* TIM2 Alternate Function mapping */ - -/** - * @brief AF 2 selection - */ -#define GPIO_AF2_TIM3 ((uint8_t)0x02U) /* TIM3 Alternate Function mapping */ -#define GPIO_AF2_TIM4 ((uint8_t)0x02U) /* TIM4 Alternate Function mapping */ -#define GPIO_AF2_TIM5 ((uint8_t)0x02U) /* TIM5 Alternate Function mapping */ - -/** - * @brief AF 3 selection - */ -#define GPIO_AF3_TIM9 ((uint8_t)0x03U) /* TIM9 Alternate Function mapping */ -#define GPIO_AF3_TIM10 ((uint8_t)0x03U) /* TIM10 Alternate Function mapping */ -#define GPIO_AF3_TIM11 ((uint8_t)0x03U) /* TIM11 Alternate Function mapping */ - -/** - * @brief AF 4 selection - */ -#define GPIO_AF4_I2C1 ((uint8_t)0x04U) /* I2C1 Alternate Function mapping */ -#define GPIO_AF4_I2C2 ((uint8_t)0x04U) /* I2C2 Alternate Function mapping */ -#define GPIO_AF4_I2C3 ((uint8_t)0x04U) /* I2C3 Alternate Function mapping */ - -/** - * @brief AF 5 selection - */ -#define GPIO_AF5_SPI1 ((uint8_t)0x05U) /* SPI1/I2S1 Alternate Function mapping */ -#define GPIO_AF5_SPI2 ((uint8_t)0x05U) /* SPI2/I2S2 Alternate Function mapping */ -#define GPIO_AF5_SPI3 ((uint8_t)0x05U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF5_SPI4 ((uint8_t)0x05U) /* SPI4 Alternate Function mapping */ -#define GPIO_AF5_I2S3ext ((uint8_t)0x05U) /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 6 selection - */ -#define GPIO_AF6_SPI2 ((uint8_t)0x06U) /* I2S2 Alternate Function mapping */ -#define GPIO_AF6_SPI3 ((uint8_t)0x06U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF6_SPI4 ((uint8_t)0x06U) /* SPI4/I2S4 Alternate Function mapping */ -#define GPIO_AF6_SPI5 ((uint8_t)0x06U) /* SPI5/I2S5 Alternate Function mapping */ -#define GPIO_AF6_I2S2ext ((uint8_t)0x06U) /* I2S2ext_SD Alternate Function mapping */ - -/** - * @brief AF 7 selection - */ -#define GPIO_AF7_SPI3 ((uint8_t)0x07U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF7_USART1 ((uint8_t)0x07U) /* USART1 Alternate Function mapping */ -#define GPIO_AF7_USART2 ((uint8_t)0x07U) /* USART2 Alternate Function mapping */ -#define GPIO_AF7_I2S3ext ((uint8_t)0x07U) /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 8 selection - */ -#define GPIO_AF8_USART6 ((uint8_t)0x08U) /* USART6 Alternate Function mapping */ - -/** - * @brief AF 9 selection - */ -#define GPIO_AF9_TIM14 ((uint8_t)0x09U) /* TIM14 Alternate Function mapping */ -#define GPIO_AF9_I2C2 ((uint8_t)0x09U) /* I2C2 Alternate Function mapping */ -#define GPIO_AF9_I2C3 ((uint8_t)0x09U) /* I2C3 Alternate Function mapping */ - -/** - * @brief AF 10 selection - */ -#define GPIO_AF10_OTG_FS ((uint8_t)0x0AU) /* OTG_FS Alternate Function mapping */ - -/** - * @brief AF 12 selection - */ -#define GPIO_AF12_SDIO ((uint8_t)0x0CU) /* SDIO Alternate Function mapping */ - -/** - * @brief AF 15 selection - */ -#define GPIO_AF15_EVENTOUT ((uint8_t)0x0FU) /* EVENTOUT Alternate Function mapping */ -#endif /* STM32F411xE */ - -/*---------------------------------------- STM32F410xx------------------------*/ -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -/** - * @brief AF 0 selection - */ -#define GPIO_AF0_RTC_50Hz ((uint8_t)0x00U) /* RTC_50Hz Alternate Function mapping */ -#define GPIO_AF0_MCO ((uint8_t)0x00U) /* MCO (MCO1 and MCO2) Alternate Function mapping */ -#define GPIO_AF0_TAMPER ((uint8_t)0x00U) /* TAMPER (TAMPER_1 and TAMPER_2) Alternate Function mapping */ -#define GPIO_AF0_SWJ ((uint8_t)0x00U) /* SWJ (SWD and JTAG) Alternate Function mapping */ -#define GPIO_AF0_TRACE ((uint8_t)0x00U) /* TRACE Alternate Function mapping */ - -/** - * @brief AF 1 selection - */ -#define GPIO_AF1_TIM1 ((uint8_t)0x01U) /* TIM1 Alternate Function mapping */ -#define GPIO_AF1_LPTIM1 ((uint8_t)0x01U) /* LPTIM1 Alternate Function mapping */ - -/** - * @brief AF 2 selection - */ -#define GPIO_AF2_TIM5 ((uint8_t)0x02U) /* TIM5 Alternate Function mapping */ - -/** - * @brief AF 3 selection - */ -#define GPIO_AF3_TIM9 ((uint8_t)0x03U) /* TIM9 Alternate Function mapping */ -#define GPIO_AF3_TIM11 ((uint8_t)0x03U) /* TIM11 Alternate Function mapping */ - -/** - * @brief AF 4 selection - */ -#define GPIO_AF4_I2C1 ((uint8_t)0x04U) /* I2C1 Alternate Function mapping */ -#define GPIO_AF4_I2C2 ((uint8_t)0x04U) /* I2C2 Alternate Function mapping */ -#define GPIO_AF4_FMPI2C1 ((uint8_t)0x04U) /* FMPI2C1 Alternate Function mapping */ - -/** - * @brief AF 5 selection - */ -#define GPIO_AF5_SPI1 ((uint8_t)0x05U) /* SPI1/I2S1 Alternate Function mapping */ -#if defined(STM32F410Cx) || defined(STM32F410Rx) -#define GPIO_AF5_SPI2 ((uint8_t)0x05U) /* SPI2/I2S2 Alternate Function mapping */ -#endif /* STM32F410Cx || STM32F410Rx */ - -/** - * @brief AF 6 selection - */ -#define GPIO_AF6_SPI1 ((uint8_t)0x06U) /* SPI1 Alternate Function mapping */ -#if defined(STM32F410Cx) || defined(STM32F410Rx) -#define GPIO_AF6_SPI2 ((uint8_t)0x06U) /* I2S2 Alternate Function mapping */ -#endif /* STM32F410Cx || STM32F410Rx */ -#define GPIO_AF6_SPI5 ((uint8_t)0x06U) /* SPI5/I2S5 Alternate Function mapping */ -/** - * @brief AF 7 selection - */ -#define GPIO_AF7_USART1 ((uint8_t)0x07U) /* USART1 Alternate Function mapping */ -#define GPIO_AF7_USART2 ((uint8_t)0x07U) /* USART2 Alternate Function mapping */ - -/** - * @brief AF 8 selection - */ -#define GPIO_AF8_USART6 ((uint8_t)0x08U) /* USART6 Alternate Function mapping */ - -/** - * @brief AF 9 selection - */ -#define GPIO_AF9_I2C2 ((uint8_t)0x09U) /* I2C2 Alternate Function mapping */ -#define GPIO_AF9_FMPI2C1 ((uint8_t)0x09U) /* FMPI2C1 Alternate Function mapping */ - -/** - * @brief AF 15 selection - */ -#define GPIO_AF15_EVENTOUT ((uint8_t)0x0FU) /* EVENTOUT Alternate Function mapping */ -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -/*---------------------------------------- STM32F446xx -----------------------*/ -#if defined(STM32F446xx) -/** - * @brief AF 0 selection - */ -#define GPIO_AF0_RTC_50Hz ((uint8_t)0x00U) /* RTC_50Hz Alternate Function mapping */ -#define GPIO_AF0_MCO ((uint8_t)0x00U) /* MCO (MCO1 and MCO2) Alternate Function mapping */ -#define GPIO_AF0_TAMPER ((uint8_t)0x00U) /* TAMPER (TAMPER_1 and TAMPER_2) Alternate Function mapping */ -#define GPIO_AF0_SWJ ((uint8_t)0x00U) /* SWJ (SWD and JTAG) Alternate Function mapping */ -#define GPIO_AF0_TRACE ((uint8_t)0x00U) /* TRACE Alternate Function mapping */ - -/** - * @brief AF 1 selection - */ -#define GPIO_AF1_TIM1 ((uint8_t)0x01U) /* TIM1 Alternate Function mapping */ -#define GPIO_AF1_TIM2 ((uint8_t)0x01U) /* TIM2 Alternate Function mapping */ - -/** - * @brief AF 2 selection - */ -#define GPIO_AF2_TIM3 ((uint8_t)0x02U) /* TIM3 Alternate Function mapping */ -#define GPIO_AF2_TIM4 ((uint8_t)0x02U) /* TIM4 Alternate Function mapping */ -#define GPIO_AF2_TIM5 ((uint8_t)0x02U) /* TIM5 Alternate Function mapping */ - -/** - * @brief AF 3 selection - */ -#define GPIO_AF3_TIM8 ((uint8_t)0x03U) /* TIM8 Alternate Function mapping */ -#define GPIO_AF3_TIM9 ((uint8_t)0x03U) /* TIM9 Alternate Function mapping */ -#define GPIO_AF3_TIM10 ((uint8_t)0x03U) /* TIM10 Alternate Function mapping */ -#define GPIO_AF3_TIM11 ((uint8_t)0x03U) /* TIM11 Alternate Function mapping */ -#define GPIO_AF3_CEC ((uint8_t)0x03U) /* CEC Alternate Function mapping */ - -/** - * @brief AF 4 selection - */ -#define GPIO_AF4_I2C1 ((uint8_t)0x04U) /* I2C1 Alternate Function mapping */ -#define GPIO_AF4_I2C2 ((uint8_t)0x04U) /* I2C2 Alternate Function mapping */ -#define GPIO_AF4_I2C3 ((uint8_t)0x04U) /* I2C3 Alternate Function mapping */ -#define GPIO_AF4_FMPI2C1 ((uint8_t)0x04U) /* FMPI2C1 Alternate Function mapping */ -#define GPIO_AF4_CEC ((uint8_t)0x04U) /* CEC Alternate Function mapping */ - -/** - * @brief AF 5 selection - */ -#define GPIO_AF5_SPI1 ((uint8_t)0x05U) /* SPI1/I2S1 Alternate Function mapping */ -#define GPIO_AF5_SPI2 ((uint8_t)0x05U) /* SPI2/I2S2 Alternate Function mapping */ -#define GPIO_AF5_SPI3 ((uint8_t)0x05U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF5_SPI4 ((uint8_t)0x05U) /* SPI4 Alternate Function mapping */ - -/** - * @brief AF 6 selection - */ -#define GPIO_AF6_SPI2 ((uint8_t)0x06U) /* SPI2/I2S2 Alternate Function mapping */ -#define GPIO_AF6_SPI3 ((uint8_t)0x06U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF6_SPI4 ((uint8_t)0x06U) /* SPI4 Alternate Function mapping */ -#define GPIO_AF6_SAI1 ((uint8_t)0x06U) /* SAI1 Alternate Function mapping */ - -/** - * @brief AF 7 selection - */ -#define GPIO_AF7_USART1 ((uint8_t)0x07U) /* USART1 Alternate Function mapping */ -#define GPIO_AF7_USART2 ((uint8_t)0x07U) /* USART2 Alternate Function mapping */ -#define GPIO_AF7_USART3 ((uint8_t)0x07U) /* USART3 Alternate Function mapping */ -#define GPIO_AF7_UART5 ((uint8_t)0x07U) /* UART5 Alternate Function mapping */ -#define GPIO_AF7_SPI2 ((uint8_t)0x07U) /* SPI2/I2S2 Alternate Function mapping */ -#define GPIO_AF7_SPI3 ((uint8_t)0x07U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF7_SPDIFRX ((uint8_t)0x07U) /* SPDIFRX Alternate Function mapping */ - -/** - * @brief AF 8 selection - */ -#define GPIO_AF8_UART4 ((uint8_t)0x08U) /* UART4 Alternate Function mapping */ -#define GPIO_AF8_UART5 ((uint8_t)0x08U) /* UART5 Alternate Function mapping */ -#define GPIO_AF8_USART6 ((uint8_t)0x08U) /* USART6 Alternate Function mapping */ -#define GPIO_AF8_SPDIFRX ((uint8_t)0x08U) /* SPDIFRX Alternate Function mapping */ -#define GPIO_AF8_SAI2 ((uint8_t)0x08U) /* SAI2 Alternate Function mapping */ - -/** - * @brief AF 9 selection - */ -#define GPIO_AF9_CAN1 ((uint8_t)0x09U) /* CAN1 Alternate Function mapping */ -#define GPIO_AF9_CAN2 ((uint8_t)0x09U) /* CAN2 Alternate Function mapping */ -#define GPIO_AF9_TIM12 ((uint8_t)0x09U) /* TIM12 Alternate Function mapping */ -#define GPIO_AF9_TIM13 ((uint8_t)0x09U) /* TIM13 Alternate Function mapping */ -#define GPIO_AF9_TIM14 ((uint8_t)0x09U) /* TIM14 Alternate Function mapping */ -#define GPIO_AF9_QSPI ((uint8_t)0x09U) /* QSPI Alternate Function mapping */ - -/** - * @brief AF 10 selection - */ -#define GPIO_AF10_OTG_FS ((uint8_t)0x0AU) /* OTG_FS Alternate Function mapping */ -#define GPIO_AF10_OTG_HS ((uint8_t)0x0AU) /* OTG_HS Alternate Function mapping */ -#define GPIO_AF10_SAI2 ((uint8_t)0x0AU) /* SAI2 Alternate Function mapping */ -#define GPIO_AF10_QSPI ((uint8_t)0x0AU) /* QSPI Alternate Function mapping */ - -/** - * @brief AF 11 selection - */ -#define GPIO_AF11_ETH ((uint8_t)0x0BU) /* ETHERNET Alternate Function mapping */ - -/** - * @brief AF 12 selection - */ -#define GPIO_AF12_FMC ((uint8_t)0x0CU) /* FMC Alternate Function mapping */ -#define GPIO_AF12_OTG_HS_FS ((uint8_t)0x0CU) /* OTG HS configured in FS, Alternate Function mapping */ -#define GPIO_AF12_SDIO ((uint8_t)0x0CU) /* SDIO Alternate Function mapping */ - -/** - * @brief AF 13 selection - */ -#define GPIO_AF13_DCMI ((uint8_t)0x0DU) /* DCMI Alternate Function mapping */ - -/** - * @brief AF 15 selection - */ -#define GPIO_AF15_EVENTOUT ((uint8_t)0x0FU) /* EVENTOUT Alternate Function mapping */ - -#endif /* STM32F446xx */ -/*----------------------------------------------------------------------------*/ - -/*-------------------------------- STM32F469xx/STM32F479xx--------------------*/ -#if defined(STM32F469xx) || defined(STM32F479xx) -/** - * @brief AF 0 selection - */ -#define GPIO_AF0_RTC_50Hz ((uint8_t)0x00U) /* RTC_50Hz Alternate Function mapping */ -#define GPIO_AF0_MCO ((uint8_t)0x00U) /* MCO (MCO1 and MCO2) Alternate Function mapping */ -#define GPIO_AF0_TAMPER ((uint8_t)0x00U) /* TAMPER (TAMPER_1 and TAMPER_2) Alternate Function mapping */ -#define GPIO_AF0_SWJ ((uint8_t)0x00U) /* SWJ (SWD and JTAG) Alternate Function mapping */ -#define GPIO_AF0_TRACE ((uint8_t)0x00U) /* TRACE Alternate Function mapping */ - -/** - * @brief AF 1 selection - */ -#define GPIO_AF1_TIM1 ((uint8_t)0x01U) /* TIM1 Alternate Function mapping */ -#define GPIO_AF1_TIM2 ((uint8_t)0x01U) /* TIM2 Alternate Function mapping */ - -/** - * @brief AF 2 selection - */ -#define GPIO_AF2_TIM3 ((uint8_t)0x02U) /* TIM3 Alternate Function mapping */ -#define GPIO_AF2_TIM4 ((uint8_t)0x02U) /* TIM4 Alternate Function mapping */ -#define GPIO_AF2_TIM5 ((uint8_t)0x02U) /* TIM5 Alternate Function mapping */ - -/** - * @brief AF 3 selection - */ -#define GPIO_AF3_TIM8 ((uint8_t)0x03U) /* TIM8 Alternate Function mapping */ -#define GPIO_AF3_TIM9 ((uint8_t)0x03U) /* TIM9 Alternate Function mapping */ -#define GPIO_AF3_TIM10 ((uint8_t)0x03U) /* TIM10 Alternate Function mapping */ -#define GPIO_AF3_TIM11 ((uint8_t)0x03U) /* TIM11 Alternate Function mapping */ - -/** - * @brief AF 4 selection - */ -#define GPIO_AF4_I2C1 ((uint8_t)0x04U) /* I2C1 Alternate Function mapping */ -#define GPIO_AF4_I2C2 ((uint8_t)0x04U) /* I2C2 Alternate Function mapping */ -#define GPIO_AF4_I2C3 ((uint8_t)0x04U) /* I2C3 Alternate Function mapping */ - -/** - * @brief AF 5 selection - */ -#define GPIO_AF5_SPI1 ((uint8_t)0x05U) /* SPI1 Alternate Function mapping */ -#define GPIO_AF5_SPI2 ((uint8_t)0x05U) /* SPI2/I2S2 Alternate Function mapping */ -#define GPIO_AF5_SPI3 ((uint8_t)0x05U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF5_SPI4 ((uint8_t)0x05U) /* SPI4 Alternate Function mapping */ -#define GPIO_AF5_SPI5 ((uint8_t)0x05U) /* SPI5 Alternate Function mapping */ -#define GPIO_AF5_SPI6 ((uint8_t)0x05U) /* SPI6 Alternate Function mapping */ -#define GPIO_AF5_I2S3ext ((uint8_t)0x05U) /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 6 selection - */ -#define GPIO_AF6_SPI3 ((uint8_t)0x06U) /* SPI3/I2S3 Alternate Function mapping */ -#define GPIO_AF6_I2S2ext ((uint8_t)0x06U) /* I2S2ext_SD Alternate Function mapping */ -#define GPIO_AF6_SAI1 ((uint8_t)0x06U) /* SAI1 Alternate Function mapping */ - -/** - * @brief AF 7 selection - */ -#define GPIO_AF7_USART1 ((uint8_t)0x07U) /* USART1 Alternate Function mapping */ -#define GPIO_AF7_USART2 ((uint8_t)0x07U) /* USART2 Alternate Function mapping */ -#define GPIO_AF7_USART3 ((uint8_t)0x07U) /* USART3 Alternate Function mapping */ -#define GPIO_AF7_I2S3ext ((uint8_t)0x07U) /* I2S3ext_SD Alternate Function mapping */ - -/** - * @brief AF 8 selection - */ -#define GPIO_AF8_UART4 ((uint8_t)0x08U) /* UART4 Alternate Function mapping */ -#define GPIO_AF8_UART5 ((uint8_t)0x08U) /* UART5 Alternate Function mapping */ -#define GPIO_AF8_USART6 ((uint8_t)0x08U) /* USART6 Alternate Function mapping */ -#define GPIO_AF8_UART7 ((uint8_t)0x08U) /* UART7 Alternate Function mapping */ -#define GPIO_AF8_UART8 ((uint8_t)0x08U) /* UART8 Alternate Function mapping */ - -/** - * @brief AF 9 selection - */ -#define GPIO_AF9_CAN1 ((uint8_t)0x09U) /* CAN1 Alternate Function mapping */ -#define GPIO_AF9_CAN2 ((uint8_t)0x09U) /* CAN2 Alternate Function mapping */ -#define GPIO_AF9_TIM12 ((uint8_t)0x09U) /* TIM12 Alternate Function mapping */ -#define GPIO_AF9_TIM13 ((uint8_t)0x09U) /* TIM13 Alternate Function mapping */ -#define GPIO_AF9_TIM14 ((uint8_t)0x09U) /* TIM14 Alternate Function mapping */ -#define GPIO_AF9_LTDC ((uint8_t)0x09U) /* LCD-TFT Alternate Function mapping */ -#define GPIO_AF9_QSPI ((uint8_t)0x09U) /* QSPI Alternate Function mapping */ - -/** - * @brief AF 10 selection - */ -#define GPIO_AF10_OTG_FS ((uint8_t)0x0AU) /* OTG_FS Alternate Function mapping */ -#define GPIO_AF10_OTG_HS ((uint8_t)0x0AU) /* OTG_HS Alternate Function mapping */ -#define GPIO_AF10_QSPI ((uint8_t)0x0AU) /* QSPI Alternate Function mapping */ - -/** - * @brief AF 11 selection - */ -#define GPIO_AF11_ETH ((uint8_t)0x0BU) /* ETHERNET Alternate Function mapping */ - -/** - * @brief AF 12 selection - */ -#define GPIO_AF12_FMC ((uint8_t)0x0CU) /* FMC Alternate Function mapping */ -#define GPIO_AF12_OTG_HS_FS ((uint8_t)0x0CU) /* OTG HS configured in FS, Alternate Function mapping */ -#define GPIO_AF12_SDIO ((uint8_t)0x0CU) /* SDIO Alternate Function mapping */ - -/** - * @brief AF 13 selection - */ -#define GPIO_AF13_DCMI ((uint8_t)0x0DU) /* DCMI Alternate Function mapping */ -#define GPIO_AF13_DSI ((uint8_t)0x0DU) /* DSI Alternate Function mapping */ - -/** - * @brief AF 14 selection - */ -#define GPIO_AF14_LTDC ((uint8_t)0x0EU) /* LCD-TFT Alternate Function mapping */ - -/** - * @brief AF 15 selection - */ -#define GPIO_AF15_EVENTOUT ((uint8_t)0x0FU) /* EVENTOUT Alternate Function mapping */ - -#endif /* STM32F469xx || STM32F479xx */ -/*----------------------------------------------------------------------------*/ -/** - * @} - */ - -/** - * @} - */ - -/* Exported macro ------------------------------------------------------------*/ -/** @defgroup GPIOEx_Exported_Macros GPIO Exported Macros - * @{ - */ -/** - * @} - */ - -/* Exported functions --------------------------------------------------------*/ -/** @defgroup GPIOEx_Exported_Functions GPIO Exported Functions - * @{ - */ -/** - * @} - */ - -/* Private types -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/* Private constants ---------------------------------------------------------*/ -/** @defgroup GPIOEx_Private_Constants GPIO Private Constants - * @{ - */ -/** - * @} - */ - -/* Private macros ------------------------------------------------------------*/ -/** @defgroup GPIOEx_Private_Macros GPIO Private Macros - * @{ - */ -/** @defgroup GPIOEx_Get_Port_Index GPIO Get Port Index - * @{ - */ -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) -#define GPIO_GET_INDEX(__GPIOx__) (uint8_t)(((__GPIOx__) == (GPIOA))? 0U :\ - ((__GPIOx__) == (GPIOB))? 1U :\ - ((__GPIOx__) == (GPIOC))? 2U :\ - ((__GPIOx__) == (GPIOD))? 3U :\ - ((__GPIOx__) == (GPIOE))? 4U :\ - ((__GPIOx__) == (GPIOF))? 5U :\ - ((__GPIOx__) == (GPIOG))? 6U :\ - ((__GPIOx__) == (GPIOH))? 7U :\ - ((__GPIOx__) == (GPIOI))? 8U : 9U) -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F469xx) || defined(STM32F479xx) -#define GPIO_GET_INDEX(__GPIOx__) (uint8_t)(((__GPIOx__) == (GPIOA))? 0U :\ - ((__GPIOx__) == (GPIOB))? 1U :\ - ((__GPIOx__) == (GPIOC))? 2U :\ - ((__GPIOx__) == (GPIOD))? 3U :\ - ((__GPIOx__) == (GPIOE))? 4U :\ - ((__GPIOx__) == (GPIOF))? 5U :\ - ((__GPIOx__) == (GPIOG))? 6U :\ - ((__GPIOx__) == (GPIOH))? 7U :\ - ((__GPIOx__) == (GPIOI))? 8U :\ - ((__GPIOx__) == (GPIOJ))? 9U : 10U) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -#define GPIO_GET_INDEX(__GPIOx__) (uint8_t)(((__GPIOx__) == (GPIOA))? 0U :\ - ((__GPIOx__) == (GPIOB))? 1U :\ - ((__GPIOx__) == (GPIOC))? 2U :\ - ((__GPIOx__) == (GPIOH))? 7U : 8U) -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) -#define GPIO_GET_INDEX(__GPIOx__) (uint8_t)(((__GPIOx__) == (GPIOA))? 0U :\ - ((__GPIOx__) == (GPIOB))? 1U :\ - ((__GPIOx__) == (GPIOC))? 2U :\ - ((__GPIOx__) == (GPIOD))? 3U :\ - ((__GPIOx__) == (GPIOE))? 4U : 5U) -#endif /* STM32F401xC || STM32F401xE || STM32F411xE */ - -#if defined(STM32F446xx) || defined(STM32F412Zx) ||defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -#define GPIO_GET_INDEX(__GPIOx__) (uint8_t)(((__GPIOx__) == (GPIOA))? 0U :\ - ((__GPIOx__) == (GPIOB))? 1U :\ - ((__GPIOx__) == (GPIOC))? 2U :\ - ((__GPIOx__) == (GPIOD))? 3U :\ - ((__GPIOx__) == (GPIOE))? 4U :\ - ((__GPIOx__) == (GPIOF))? 5U :\ - ((__GPIOx__) == (GPIOG))? 6U : 8U) -#endif /* STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -/** - * @} - */ - -/** @defgroup GPIOEx_IS_Alternat_function_selection GPIO Check Alternate Function - * @{ - */ -/*------------------------- STM32F429xx/STM32F439xx---------------------------*/ -#if defined(STM32F429xx) || defined(STM32F439xx) -#define IS_GPIO_AF(AF) (((AF) == GPIO_AF0_RTC_50Hz) || ((AF) == GPIO_AF9_TIM14) || \ - ((AF) == GPIO_AF0_MCO) || ((AF) == GPIO_AF0_TAMPER) || \ - ((AF) == GPIO_AF0_SWJ) || ((AF) == GPIO_AF0_TRACE) || \ - ((AF) == GPIO_AF1_TIM1) || ((AF) == GPIO_AF1_TIM2) || \ - ((AF) == GPIO_AF2_TIM3) || ((AF) == GPIO_AF2_TIM4) || \ - ((AF) == GPIO_AF2_TIM5) || ((AF) == GPIO_AF3_TIM8) || \ - ((AF) == GPIO_AF4_I2C1) || ((AF) == GPIO_AF4_I2C2) || \ - ((AF) == GPIO_AF4_I2C3) || ((AF) == GPIO_AF5_SPI1) || \ - ((AF) == GPIO_AF5_SPI2) || ((AF) == GPIO_AF9_TIM13) || \ - ((AF) == GPIO_AF6_SPI3) || ((AF) == GPIO_AF9_TIM12) || \ - ((AF) == GPIO_AF7_USART1) || ((AF) == GPIO_AF7_USART2) || \ - ((AF) == GPIO_AF7_USART3) || ((AF) == GPIO_AF8_UART4) || \ - ((AF) == GPIO_AF8_UART5) || ((AF) == GPIO_AF8_USART6) || \ - ((AF) == GPIO_AF9_CAN1) || ((AF) == GPIO_AF9_CAN2) || \ - ((AF) == GPIO_AF10_OTG_FS) || ((AF) == GPIO_AF10_OTG_HS) || \ - ((AF) == GPIO_AF11_ETH) || ((AF) == GPIO_AF12_OTG_HS_FS) || \ - ((AF) == GPIO_AF12_SDIO) || ((AF) == GPIO_AF13_DCMI) || \ - ((AF) == GPIO_AF15_EVENTOUT) || ((AF) == GPIO_AF5_SPI4) || \ - ((AF) == GPIO_AF5_SPI5) || ((AF) == GPIO_AF5_SPI6) || \ - ((AF) == GPIO_AF8_UART7) || ((AF) == GPIO_AF8_UART8) || \ - ((AF) == GPIO_AF12_FMC) || ((AF) == GPIO_AF6_SAI1) || \ - ((AF) == GPIO_AF14_LTDC)) - -#endif /* STM32F429xx || STM32F439xx */ -/*----------------------------------------------------------------------------*/ - -/*---------------------------------- STM32F427xx/STM32F437xx------------------*/ -#if defined(STM32F427xx) || defined(STM32F437xx) -#define IS_GPIO_AF(AF) (((AF) == GPIO_AF0_RTC_50Hz) || ((AF) == GPIO_AF9_TIM14) || \ - ((AF) == GPIO_AF0_MCO) || ((AF) == GPIO_AF0_TAMPER) || \ - ((AF) == GPIO_AF0_SWJ) || ((AF) == GPIO_AF0_TRACE) || \ - ((AF) == GPIO_AF1_TIM1) || ((AF) == GPIO_AF1_TIM2) || \ - ((AF) == GPIO_AF2_TIM3) || ((AF) == GPIO_AF2_TIM4) || \ - ((AF) == GPIO_AF2_TIM5) || ((AF) == GPIO_AF3_TIM8) || \ - ((AF) == GPIO_AF4_I2C1) || ((AF) == GPIO_AF4_I2C2) || \ - ((AF) == GPIO_AF4_I2C3) || ((AF) == GPIO_AF5_SPI1) || \ - ((AF) == GPIO_AF5_SPI2) || ((AF) == GPIO_AF9_TIM13) || \ - ((AF) == GPIO_AF6_SPI3) || ((AF) == GPIO_AF9_TIM12) || \ - ((AF) == GPIO_AF7_USART1) || ((AF) == GPIO_AF7_USART2) || \ - ((AF) == GPIO_AF7_USART3) || ((AF) == GPIO_AF8_UART4) || \ - ((AF) == GPIO_AF8_UART5) || ((AF) == GPIO_AF8_USART6) || \ - ((AF) == GPIO_AF9_CAN1) || ((AF) == GPIO_AF9_CAN2) || \ - ((AF) == GPIO_AF10_OTG_FS) || ((AF) == GPIO_AF10_OTG_HS) || \ - ((AF) == GPIO_AF11_ETH) || ((AF) == GPIO_AF12_OTG_HS_FS) || \ - ((AF) == GPIO_AF12_SDIO) || ((AF) == GPIO_AF13_DCMI) || \ - ((AF) == GPIO_AF15_EVENTOUT) || ((AF) == GPIO_AF5_SPI4) || \ - ((AF) == GPIO_AF5_SPI5) || ((AF) == GPIO_AF5_SPI6) || \ - ((AF) == GPIO_AF8_UART7) || ((AF) == GPIO_AF8_UART8) || \ - ((AF) == GPIO_AF12_FMC) || ((AF) == GPIO_AF6_SAI1)) - -#endif /* STM32F427xx || STM32F437xx */ -/*----------------------------------------------------------------------------*/ - -/*---------------------------------- STM32F407xx/STM32F417xx------------------*/ -#if defined(STM32F407xx) || defined(STM32F417xx) -#define IS_GPIO_AF(AF) (((AF) == GPIO_AF0_RTC_50Hz) || ((AF) == GPIO_AF9_TIM14) || \ - ((AF) == GPIO_AF0_MCO) || ((AF) == GPIO_AF0_TAMPER) || \ - ((AF) == GPIO_AF0_SWJ) || ((AF) == GPIO_AF0_TRACE) || \ - ((AF) == GPIO_AF1_TIM1) || ((AF) == GPIO_AF1_TIM2) || \ - ((AF) == GPIO_AF2_TIM3) || ((AF) == GPIO_AF2_TIM4) || \ - ((AF) == GPIO_AF2_TIM5) || ((AF) == GPIO_AF3_TIM8) || \ - ((AF) == GPIO_AF4_I2C1) || ((AF) == GPIO_AF4_I2C2) || \ - ((AF) == GPIO_AF4_I2C3) || ((AF) == GPIO_AF5_SPI1) || \ - ((AF) == GPIO_AF5_SPI2) || ((AF) == GPIO_AF9_TIM13) || \ - ((AF) == GPIO_AF6_SPI3) || ((AF) == GPIO_AF9_TIM12) || \ - ((AF) == GPIO_AF7_USART1) || ((AF) == GPIO_AF7_USART2) || \ - ((AF) == GPIO_AF7_USART3) || ((AF) == GPIO_AF8_UART4) || \ - ((AF) == GPIO_AF8_UART5) || ((AF) == GPIO_AF8_USART6) || \ - ((AF) == GPIO_AF9_CAN1) || ((AF) == GPIO_AF9_CAN2) || \ - ((AF) == GPIO_AF10_OTG_FS) || ((AF) == GPIO_AF10_OTG_HS) || \ - ((AF) == GPIO_AF11_ETH) || ((AF) == GPIO_AF12_OTG_HS_FS) || \ - ((AF) == GPIO_AF12_SDIO) || ((AF) == GPIO_AF13_DCMI) || \ - ((AF) == GPIO_AF12_FSMC) || ((AF) == GPIO_AF15_EVENTOUT)) - -#endif /* STM32F407xx || STM32F417xx */ -/*----------------------------------------------------------------------------*/ - -/*---------------------------------- STM32F405xx/STM32F415xx------------------*/ -#if defined(STM32F405xx) || defined(STM32F415xx) -#define IS_GPIO_AF(AF) (((AF) == GPIO_AF0_RTC_50Hz) || ((AF) == GPIO_AF9_TIM14) || \ - ((AF) == GPIO_AF0_MCO) || ((AF) == GPIO_AF0_TAMPER) || \ - ((AF) == GPIO_AF0_SWJ) || ((AF) == GPIO_AF0_TRACE) || \ - ((AF) == GPIO_AF1_TIM1) || ((AF) == GPIO_AF1_TIM2) || \ - ((AF) == GPIO_AF2_TIM3) || ((AF) == GPIO_AF2_TIM4) || \ - ((AF) == GPIO_AF2_TIM5) || ((AF) == GPIO_AF3_TIM8) || \ - ((AF) == GPIO_AF4_I2C1) || ((AF) == GPIO_AF4_I2C2) || \ - ((AF) == GPIO_AF4_I2C3) || ((AF) == GPIO_AF5_SPI1) || \ - ((AF) == GPIO_AF5_SPI2) || ((AF) == GPIO_AF9_TIM13) || \ - ((AF) == GPIO_AF6_SPI3) || ((AF) == GPIO_AF9_TIM12) || \ - ((AF) == GPIO_AF7_USART1) || ((AF) == GPIO_AF7_USART2) || \ - ((AF) == GPIO_AF7_USART3) || ((AF) == GPIO_AF8_UART4) || \ - ((AF) == GPIO_AF8_UART5) || ((AF) == GPIO_AF8_USART6) || \ - ((AF) == GPIO_AF9_CAN1) || ((AF) == GPIO_AF9_CAN2) || \ - ((AF) == GPIO_AF10_OTG_FS) || ((AF) == GPIO_AF10_OTG_HS) || \ - ((AF) == GPIO_AF12_OTG_HS_FS) || ((AF) == GPIO_AF12_SDIO) || \ - ((AF) == GPIO_AF12_FSMC) || ((AF) == GPIO_AF15_EVENTOUT)) - -#endif /* STM32F405xx || STM32F415xx */ - -/*----------------------------------------------------------------------------*/ - -/*---------------------------------------- STM32F401xx------------------------*/ -#if defined(STM32F401xC) || defined(STM32F401xE) -#define IS_GPIO_AF(AF) (((AF) == GPIO_AF0_RTC_50Hz) || ((AF) == GPIO_AF9_TIM14) || \ - ((AF) == GPIO_AF0_MCO) || ((AF) == GPIO_AF0_TAMPER) || \ - ((AF) == GPIO_AF0_SWJ) || ((AF) == GPIO_AF0_TRACE) || \ - ((AF) == GPIO_AF1_TIM1) || ((AF) == GPIO_AF1_TIM2) || \ - ((AF) == GPIO_AF2_TIM3) || ((AF) == GPIO_AF2_TIM4) || \ - ((AF) == GPIO_AF2_TIM5) || ((AF) == GPIO_AF4_I2C1) || \ - ((AF) == GPIO_AF4_I2C2) || ((AF) == GPIO_AF4_I2C3) || \ - ((AF) == GPIO_AF5_SPI1) || ((AF) == GPIO_AF5_SPI2) || \ - ((AF) == GPIO_AF6_SPI3) || ((AF) == GPIO_AF5_SPI4) || \ - ((AF) == GPIO_AF7_USART1) || ((AF) == GPIO_AF7_USART2) || \ - ((AF) == GPIO_AF8_USART6) || ((AF) == GPIO_AF10_OTG_FS) || \ - ((AF) == GPIO_AF9_I2C2) || ((AF) == GPIO_AF9_I2C3) || \ - ((AF) == GPIO_AF12_SDIO) || ((AF) == GPIO_AF15_EVENTOUT)) - -#endif /* STM32F401xC || STM32F401xE */ -/*----------------------------------------------------------------------------*/ -/*---------------------------------------- STM32F410xx------------------------*/ -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -#define IS_GPIO_AF(AF) (((AF) < 10U) || ((AF) == 15U)) -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -/*---------------------------------------- STM32F411xx------------------------*/ -#if defined(STM32F411xE) -#define IS_GPIO_AF(AF) (((AF) == GPIO_AF0_RTC_50Hz) || ((AF) == GPIO_AF9_TIM14) || \ - ((AF) == GPIO_AF0_MCO) || ((AF) == GPIO_AF0_TAMPER) || \ - ((AF) == GPIO_AF0_SWJ) || ((AF) == GPIO_AF0_TRACE) || \ - ((AF) == GPIO_AF1_TIM1) || ((AF) == GPIO_AF1_TIM2) || \ - ((AF) == GPIO_AF2_TIM3) || ((AF) == GPIO_AF2_TIM4) || \ - ((AF) == GPIO_AF2_TIM5) || ((AF) == GPIO_AF4_I2C1) || \ - ((AF) == GPIO_AF4_I2C2) || ((AF) == GPIO_AF4_I2C3) || \ - ((AF) == GPIO_AF5_SPI1) || ((AF) == GPIO_AF5_SPI2) || \ - ((AF) == GPIO_AF5_SPI3) || ((AF) == GPIO_AF6_SPI4) || \ - ((AF) == GPIO_AF6_SPI3) || ((AF) == GPIO_AF5_SPI4) || \ - ((AF) == GPIO_AF6_SPI5) || ((AF) == GPIO_AF7_SPI3) || \ - ((AF) == GPIO_AF7_USART1) || ((AF) == GPIO_AF7_USART2) || \ - ((AF) == GPIO_AF8_USART6) || ((AF) == GPIO_AF10_OTG_FS) || \ - ((AF) == GPIO_AF9_I2C2) || ((AF) == GPIO_AF9_I2C3) || \ - ((AF) == GPIO_AF12_SDIO) || ((AF) == GPIO_AF15_EVENTOUT)) - -#endif /* STM32F411xE */ -/*----------------------------------------------------------------------------*/ - -/*----------------------------------------------- STM32F446xx ----------------*/ -#if defined(STM32F446xx) -#define IS_GPIO_AF(AF) (((AF) == GPIO_AF0_RTC_50Hz) || ((AF) == GPIO_AF9_TIM14) || \ - ((AF) == GPIO_AF0_MCO) || ((AF) == GPIO_AF0_TAMPER) || \ - ((AF) == GPIO_AF0_SWJ) || ((AF) == GPIO_AF0_TRACE) || \ - ((AF) == GPIO_AF1_TIM1) || ((AF) == GPIO_AF1_TIM2) || \ - ((AF) == GPIO_AF2_TIM3) || ((AF) == GPIO_AF2_TIM4) || \ - ((AF) == GPIO_AF2_TIM5) || ((AF) == GPIO_AF3_TIM8) || \ - ((AF) == GPIO_AF4_I2C1) || ((AF) == GPIO_AF4_I2C2) || \ - ((AF) == GPIO_AF4_I2C3) || ((AF) == GPIO_AF5_SPI1) || \ - ((AF) == GPIO_AF5_SPI2) || ((AF) == GPIO_AF9_TIM13) || \ - ((AF) == GPIO_AF6_SPI3) || ((AF) == GPIO_AF9_TIM12) || \ - ((AF) == GPIO_AF7_USART1) || ((AF) == GPIO_AF7_USART2) || \ - ((AF) == GPIO_AF7_USART3) || ((AF) == GPIO_AF8_UART4) || \ - ((AF) == GPIO_AF8_UART5) || ((AF) == GPIO_AF8_USART6) || \ - ((AF) == GPIO_AF9_CAN1) || ((AF) == GPIO_AF9_CAN2) || \ - ((AF) == GPIO_AF10_OTG_FS) || ((AF) == GPIO_AF10_OTG_HS) || \ - ((AF) == GPIO_AF11_ETH) || ((AF) == GPIO_AF12_OTG_HS_FS) || \ - ((AF) == GPIO_AF12_SDIO) || ((AF) == GPIO_AF13_DCMI) || \ - ((AF) == GPIO_AF15_EVENTOUT) || ((AF) == GPIO_AF5_SPI4) || \ - ((AF) == GPIO_AF12_FMC) || ((AF) == GPIO_AF6_SAI1) || \ - ((AF) == GPIO_AF3_CEC) || ((AF) == GPIO_AF4_CEC) || \ - ((AF) == GPIO_AF5_SPI3) || ((AF) == GPIO_AF6_SPI2) || \ - ((AF) == GPIO_AF6_SPI4) || ((AF) == GPIO_AF7_UART5) || \ - ((AF) == GPIO_AF7_SPI2) || ((AF) == GPIO_AF7_SPI3) || \ - ((AF) == GPIO_AF7_SPDIFRX) || ((AF) == GPIO_AF8_SPDIFRX) || \ - ((AF) == GPIO_AF8_SAI2) || ((AF) == GPIO_AF9_QSPI) || \ - ((AF) == GPIO_AF10_SAI2) || ((AF) == GPIO_AF10_QSPI)) - -#endif /* STM32F446xx */ -/*----------------------------------------------------------------------------*/ - -/*------------------------------------------- STM32F469xx/STM32F479xx --------*/ -#if defined(STM32F469xx) || defined(STM32F479xx) -#define IS_GPIO_AF(AF) (((AF) == GPIO_AF0_RTC_50Hz) || ((AF) == GPIO_AF9_TIM14) || \ - ((AF) == GPIO_AF0_MCO) || ((AF) == GPIO_AF0_TAMPER) || \ - ((AF) == GPIO_AF0_SWJ) || ((AF) == GPIO_AF0_TRACE) || \ - ((AF) == GPIO_AF1_TIM1) || ((AF) == GPIO_AF1_TIM2) || \ - ((AF) == GPIO_AF2_TIM3) || ((AF) == GPIO_AF2_TIM4) || \ - ((AF) == GPIO_AF2_TIM5) || ((AF) == GPIO_AF3_TIM8) || \ - ((AF) == GPIO_AF4_I2C1) || ((AF) == GPIO_AF4_I2C2) || \ - ((AF) == GPIO_AF4_I2C3) || ((AF) == GPIO_AF5_SPI1) || \ - ((AF) == GPIO_AF5_SPI2) || ((AF) == GPIO_AF9_TIM13) || \ - ((AF) == GPIO_AF6_SPI3) || ((AF) == GPIO_AF9_TIM12) || \ - ((AF) == GPIO_AF7_USART1) || ((AF) == GPIO_AF7_USART2) || \ - ((AF) == GPIO_AF7_USART3) || ((AF) == GPIO_AF8_UART4) || \ - ((AF) == GPIO_AF8_UART5) || ((AF) == GPIO_AF8_USART6) || \ - ((AF) == GPIO_AF9_CAN1) || ((AF) == GPIO_AF9_CAN2) || \ - ((AF) == GPIO_AF10_OTG_FS) || ((AF) == GPIO_AF10_OTG_HS) || \ - ((AF) == GPIO_AF11_ETH) || ((AF) == GPIO_AF12_OTG_HS_FS) || \ - ((AF) == GPIO_AF12_SDIO) || ((AF) == GPIO_AF13_DCMI) || \ - ((AF) == GPIO_AF15_EVENTOUT) || ((AF) == GPIO_AF5_SPI4) || \ - ((AF) == GPIO_AF5_SPI5) || ((AF) == GPIO_AF5_SPI6) || \ - ((AF) == GPIO_AF8_UART7) || ((AF) == GPIO_AF8_UART8) || \ - ((AF) == GPIO_AF12_FMC) || ((AF) == GPIO_AF6_SAI1) || \ - ((AF) == GPIO_AF14_LTDC) || ((AF) == GPIO_AF13_DSI) || \ - ((AF) == GPIO_AF9_QSPI) || ((AF) == GPIO_AF10_QSPI)) - -#endif /* STM32F469xx || STM32F479xx */ -/*----------------------------------------------------------------------------*/ - -/*------------------STM32F412Zx/STM32F412Vx/STM32F412Rx/STM32F412Cx-----------*/ -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -#define IS_GPIO_AF(AF) (((AF) < 16U) && ((AF) != 11U) && ((AF) != 14U) && ((AF) != 13U)) -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ -/*----------------------------------------------------------------------------*/ - -/** - * @} - */ - -/** - * @} - */ - -/* Private functions ---------------------------------------------------------*/ -/** @defgroup GPIOEx_Private_Functions GPIO Private Functions - * @{ - */ - -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F4xx_HAL_GPIO_EX_H */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_pwr.h b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_pwr.h deleted file mode 100644 index 03cf4f6c..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_pwr.h +++ /dev/null @@ -1,449 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_pwr.h - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Header file of PWR HAL module. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_PWR_H -#define __STM32F4xx_HAL_PWR_H - -#ifdef __cplusplus -extern "C" { -#endif - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_def.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @addtogroup PWR - * @{ - */ - -/* Exported types ------------------------------------------------------------*/ - -/** @defgroup PWR_Exported_Types PWR Exported Types - * @{ - */ - -/** - * @brief PWR PVD configuration structure definition - */ -typedef struct -{ - uint32_t PVDLevel; /*!< PVDLevel: Specifies the PVD detection level. - This parameter can be a value of @ref PWR_PVD_detection_level */ - - uint32_t Mode; /*!< Mode: Specifies the operating mode for the selected pins. - This parameter can be a value of @ref PWR_PVD_Mode */ -} PWR_PVDTypeDef; - -/** - * @} - */ - -/* Exported constants --------------------------------------------------------*/ -/** @defgroup PWR_Exported_Constants PWR Exported Constants - * @{ - */ - -/** @defgroup PWR_WakeUp_Pins PWR WakeUp Pins - * @{ - */ -#define PWR_WAKEUP_PIN1 ((uint32_t)0x00000100U) -/** - * @} - */ - -/** @defgroup PWR_PVD_detection_level PWR PVD detection level - * @{ - */ -#define PWR_PVDLEVEL_0 PWR_CR_PLS_LEV0 -#define PWR_PVDLEVEL_1 PWR_CR_PLS_LEV1 -#define PWR_PVDLEVEL_2 PWR_CR_PLS_LEV2 -#define PWR_PVDLEVEL_3 PWR_CR_PLS_LEV3 -#define PWR_PVDLEVEL_4 PWR_CR_PLS_LEV4 -#define PWR_PVDLEVEL_5 PWR_CR_PLS_LEV5 -#define PWR_PVDLEVEL_6 PWR_CR_PLS_LEV6 -#define PWR_PVDLEVEL_7 PWR_CR_PLS_LEV7/* External input analog voltage - (Compare internally to VREFINT) */ -/** - * @} - */ - -/** @defgroup PWR_PVD_Mode PWR PVD Mode - * @{ - */ -#define PWR_PVD_MODE_NORMAL ((uint32_t)0x00000000U) /*!< basic mode is used */ -#define PWR_PVD_MODE_IT_RISING ((uint32_t)0x00010001U) /*!< External Interrupt Mode with Rising edge trigger detection */ -#define PWR_PVD_MODE_IT_FALLING ((uint32_t)0x00010002U) /*!< External Interrupt Mode with Falling edge trigger detection */ -#define PWR_PVD_MODE_IT_RISING_FALLING ((uint32_t)0x00010003U) /*!< External Interrupt Mode with Rising/Falling edge trigger detection */ -#define PWR_PVD_MODE_EVENT_RISING ((uint32_t)0x00020001U) /*!< Event Mode with Rising edge trigger detection */ -#define PWR_PVD_MODE_EVENT_FALLING ((uint32_t)0x00020002U) /*!< Event Mode with Falling edge trigger detection */ -#define PWR_PVD_MODE_EVENT_RISING_FALLING ((uint32_t)0x00020003U) /*!< Event Mode with Rising/Falling edge trigger detection */ -/** - * @} - */ - - -/** @defgroup PWR_Regulator_state_in_STOP_mode PWR Regulator state in SLEEP/STOP mode - * @{ - */ -#define PWR_MAINREGULATOR_ON ((uint32_t)0x00000000U) -#define PWR_LOWPOWERREGULATOR_ON PWR_CR_LPDS -/** - * @} - */ - -/** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry - * @{ - */ -#define PWR_SLEEPENTRY_WFI ((uint8_t)0x01U) -#define PWR_SLEEPENTRY_WFE ((uint8_t)0x02U) -/** - * @} - */ - -/** @defgroup PWR_STOP_mode_entry PWR STOP mode entry - * @{ - */ -#define PWR_STOPENTRY_WFI ((uint8_t)0x01U) -#define PWR_STOPENTRY_WFE ((uint8_t)0x02U) -/** - * @} - */ - -/** @defgroup PWR_Flag PWR Flag - * @{ - */ -#define PWR_FLAG_WU PWR_CSR_WUF -#define PWR_FLAG_SB PWR_CSR_SBF -#define PWR_FLAG_PVDO PWR_CSR_PVDO -#define PWR_FLAG_BRR PWR_CSR_BRR -#define PWR_FLAG_VOSRDY PWR_CSR_VOSRDY -/** - * @} - */ - -/** - * @} - */ - -/* Exported macro ------------------------------------------------------------*/ -/** @defgroup PWR_Exported_Macro PWR Exported Macro - * @{ - */ - -/** @brief Check PWR flag is set or not. - * @param __FLAG__: specifies the flag to check. - * This parameter can be one of the following values: - * @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event - * was received from the WKUP pin or from the RTC alarm (Alarm A - * or Alarm B), RTC Tamper event, RTC TimeStamp event or RTC Wakeup. - * An additional wakeup event is detected if the WKUP pin is enabled - * (by setting the EWUP bit) when the WKUP pin level is already high. - * @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was - * resumed from StandBy mode. - * @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled - * by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode - * For this reason, this bit is equal to 0 after Standby or reset - * until the PVDE bit is set. - * @arg PWR_FLAG_BRR: Backup regulator ready flag. This bit is not reset - * when the device wakes up from Standby mode or by a system reset - * or power reset. - * @arg PWR_FLAG_VOSRDY: This flag indicates that the Regulator voltage - * scaling output selection is ready. - * @retval The new state of __FLAG__ (TRUE or FALSE). - */ -#define __HAL_PWR_GET_FLAG(__FLAG__) ((PWR->CSR & (__FLAG__)) == (__FLAG__)) - -/** @brief Clear the PWR's pending flags. - * @param __FLAG__: specifies the flag to clear. - * This parameter can be one of the following values: - * @arg PWR_FLAG_WU: Wake Up flag - * @arg PWR_FLAG_SB: StandBy flag - */ -#define __HAL_PWR_CLEAR_FLAG(__FLAG__) (PWR->CR |= (__FLAG__) << 2U) - -/** - * @brief Enable the PVD Exti Line 16. - * @retval None. - */ -#define __HAL_PWR_PVD_EXTI_ENABLE_IT() (EXTI->IMR |= (PWR_EXTI_LINE_PVD)) - -/** - * @brief Disable the PVD EXTI Line 16. - * @retval None. - */ -#define __HAL_PWR_PVD_EXTI_DISABLE_IT() (EXTI->IMR &= ~(PWR_EXTI_LINE_PVD)) - -/** - * @brief Enable event on PVD Exti Line 16. - * @retval None. - */ -#define __HAL_PWR_PVD_EXTI_ENABLE_EVENT() (EXTI->EMR |= (PWR_EXTI_LINE_PVD)) - -/** - * @brief Disable event on PVD Exti Line 16. - * @retval None. - */ -#define __HAL_PWR_PVD_EXTI_DISABLE_EVENT() (EXTI->EMR &= ~(PWR_EXTI_LINE_PVD)) - -/** - * @brief Enable the PVD Extended Interrupt Rising Trigger. - * @retval None. - */ -#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE() SET_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD) - -/** - * @brief Disable the PVD Extended Interrupt Rising Trigger. - * @retval None. - */ -#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE() CLEAR_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD) - -/** - * @brief Enable the PVD Extended Interrupt Falling Trigger. - * @retval None. - */ -#define __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE() SET_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD) - - -/** - * @brief Disable the PVD Extended Interrupt Falling Trigger. - * @retval None. - */ -#define __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE() CLEAR_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD) - - -/** - * @brief PVD EXTI line configuration: set rising & falling edge trigger. - * @retval None. - */ -#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_FALLING_EDGE() do{__HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();\ - __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE();\ - }while(0) - -/** - * @brief Disable the PVD Extended Interrupt Rising & Falling Trigger. - * This parameter can be: - * @retval None. - */ -#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_FALLING_EDGE() do{__HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();\ - __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE();\ - }while(0) - -/** - * @brief checks whether the specified PVD Exti interrupt flag is set or not. - * @retval EXTI PVD Line Status. - */ -#define __HAL_PWR_PVD_EXTI_GET_FLAG() (EXTI->PR & (PWR_EXTI_LINE_PVD)) - -/** - * @brief Clear the PVD Exti flag. - * @retval None. - */ -#define __HAL_PWR_PVD_EXTI_CLEAR_FLAG() (EXTI->PR = (PWR_EXTI_LINE_PVD)) - -/** - * @brief Generates a Software interrupt on PVD EXTI line. - * @retval None - */ -#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT() (EXTI->SWIER |= (PWR_EXTI_LINE_PVD)) - -/** - * @} - */ - -/* Include PWR HAL Extension module */ -#include "stm32f4xx_hal_pwr_ex.h" - -/* Exported functions --------------------------------------------------------*/ -/** @addtogroup PWR_Exported_Functions PWR Exported Functions - * @{ - */ - -/** @addtogroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions - * @{ - */ -/* Initialization and de-initialization functions *****************************/ -void HAL_PWR_DeInit(void); -void HAL_PWR_EnableBkUpAccess(void); -void HAL_PWR_DisableBkUpAccess(void); -/** - * @} - */ - -/** @addtogroup PWR_Exported_Functions_Group2 Peripheral Control functions - * @{ - */ -/* Peripheral Control functions **********************************************/ -/* PVD configuration */ -void HAL_PWR_ConfigPVD(PWR_PVDTypeDef* sConfigPVD); -void HAL_PWR_EnablePVD(void); -void HAL_PWR_DisablePVD(void); - -/* WakeUp pins configuration */ -void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx); -void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx); - -/* Low Power modes entry */ -void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry); -void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry); -void HAL_PWR_EnterSTANDBYMode(void); - -/* Power PVD IRQ Handler */ -void HAL_PWR_PVD_IRQHandler(void); -void HAL_PWR_PVDCallback(void); - -/* Cortex System Control functions *******************************************/ -void HAL_PWR_EnableSleepOnExit(void); -void HAL_PWR_DisableSleepOnExit(void); -void HAL_PWR_EnableSEVOnPend(void); -void HAL_PWR_DisableSEVOnPend(void); -/** - * @} - */ - -/** - * @} - */ - -/* Private types -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/* Private constants ---------------------------------------------------------*/ -/** @defgroup PWR_Private_Constants PWR Private Constants - * @{ - */ - -/** @defgroup PWR_PVD_EXTI_Line PWR PVD EXTI Line - * @{ - */ -#define PWR_EXTI_LINE_PVD ((uint32_t)EXTI_IMR_MR16) /*!< External interrupt line 16 Connected to the PVD EXTI Line */ -/** - * @} - */ - -/** @defgroup PWR_register_alias_address PWR Register alias address - * @{ - */ -/* ------------- PWR registers bit address in the alias region ---------------*/ -#define PWR_OFFSET (PWR_BASE - PERIPH_BASE) -#define PWR_CR_OFFSET 0x00U -#define PWR_CSR_OFFSET 0x04U -#define PWR_CR_OFFSET_BB (PWR_OFFSET + PWR_CR_OFFSET) -#define PWR_CSR_OFFSET_BB (PWR_OFFSET + PWR_CSR_OFFSET) -/** - * @} - */ - -/** @defgroup PWR_CR_register_alias PWR CR Register alias address - * @{ - */ -/* --- CR Register ---*/ -/* Alias word address of DBP bit */ -#define DBP_BIT_NUMBER POSITION_VAL(PWR_CR_DBP) -#define CR_DBP_BB (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (DBP_BIT_NUMBER * 4U)) - -/* Alias word address of PVDE bit */ -#define PVDE_BIT_NUMBER POSITION_VAL(PWR_CR_PVDE) -#define CR_PVDE_BB (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (PVDE_BIT_NUMBER * 4U)) - -/* Alias word address of PMODE bit */ -#define PMODE_BIT_NUMBER POSITION_VAL(PWR_CR_PMODE) -#define CR_PMODE_BB (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (PMODE_BIT_NUMBER * 4U)) -/** - * @} - */ - -/** @defgroup PWR_CSR_register_alias PWR CSR Register alias address - * @{ - */ -/* --- CSR Register ---*/ -/* Alias word address of EWUP bit */ -#define EWUP_BIT_NUMBER POSITION_VAL(PWR_CSR_EWUP) -#define CSR_EWUP_BB (PERIPH_BB_BASE + (PWR_CSR_OFFSET_BB * 32U) + (EWUP_BIT_NUMBER * 4U)) -/** - * @} - */ - -/** - * @} - */ -/* Private macros ------------------------------------------------------------*/ -/** @defgroup PWR_Private_Macros PWR Private Macros - * @{ - */ - -/** @defgroup PWR_IS_PWR_Definitions PWR Private macros to check input parameters - * @{ - */ -#define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \ - ((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \ - ((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \ - ((LEVEL) == PWR_PVDLEVEL_6) || ((LEVEL) == PWR_PVDLEVEL_7)) -#define IS_PWR_PVD_MODE(MODE) (((MODE) == PWR_PVD_MODE_IT_RISING)|| ((MODE) == PWR_PVD_MODE_IT_FALLING) || \ - ((MODE) == PWR_PVD_MODE_IT_RISING_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING) || \ - ((MODE) == PWR_PVD_MODE_EVENT_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING_FALLING) || \ - ((MODE) == PWR_PVD_MODE_NORMAL)) -#define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \ - ((REGULATOR) == PWR_LOWPOWERREGULATOR_ON)) -#define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || ((ENTRY) == PWR_SLEEPENTRY_WFE)) -#define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || ((ENTRY) == PWR_STOPENTRY_WFE)) -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -#ifdef __cplusplus -} -#endif - - -#endif /* __STM32F4xx_HAL_PWR_H */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_pwr_ex.h b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_pwr_ex.h deleted file mode 100644 index 85ae8ce9..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_pwr_ex.h +++ /dev/null @@ -1,370 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_pwr_ex.h - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Header file of PWR HAL Extension module. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_PWR_EX_H -#define __STM32F4xx_HAL_PWR_EX_H - -#ifdef __cplusplus -extern "C" { -#endif - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_def.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @addtogroup PWREx - * @{ - */ - -/* Exported types ------------------------------------------------------------*/ -/* Exported constants --------------------------------------------------------*/ -/** @defgroup PWREx_Exported_Constants PWREx Exported Constants - * @{ - */ -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) - -/** @defgroup PWREx_Regulator_state_in_UnderDrive_mode PWREx Regulator state in UnderDrive mode - * @{ - */ -#define PWR_MAINREGULATOR_UNDERDRIVE_ON PWR_CR_MRUDS -#define PWR_LOWPOWERREGULATOR_UNDERDRIVE_ON ((uint32_t)(PWR_CR_LPDS | PWR_CR_LPUDS)) -/** - * @} - */ - -/** @defgroup PWREx_Over_Under_Drive_Flag PWREx Over Under Drive Flag - * @{ - */ -#define PWR_FLAG_ODRDY PWR_CSR_ODRDY -#define PWR_FLAG_ODSWRDY PWR_CSR_ODSWRDY -#define PWR_FLAG_UDRDY PWR_CSR_UDSWRDY -/** - * @} - */ -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */ - -/** @defgroup PWREx_Regulator_Voltage_Scale PWREx Regulator Voltage Scale - * @{ - */ -#if defined(STM32F405xx) || defined(STM32F407xx) || defined(STM32F415xx) || defined(STM32F417xx) -#define PWR_REGULATOR_VOLTAGE_SCALE1 PWR_CR_VOS /* Scale 1 mode(default value at reset): the maximum value of fHCLK = 168 MHz. */ -#define PWR_REGULATOR_VOLTAGE_SCALE2 ((uint32_t)0x00000000U) /* Scale 2 mode: the maximum value of fHCLK = 144 MHz. */ -#else -#define PWR_REGULATOR_VOLTAGE_SCALE1 PWR_CR_VOS /* Scale 1 mode(default value at reset): the maximum value of fHCLK is 168 MHz. It can be extended to - 180 MHz by activating the over-drive mode. */ -#define PWR_REGULATOR_VOLTAGE_SCALE2 PWR_CR_VOS_1 /* Scale 2 mode: the maximum value of fHCLK is 144 MHz. It can be extended to - 168 MHz by activating the over-drive mode. */ -#define PWR_REGULATOR_VOLTAGE_SCALE3 PWR_CR_VOS_0 /* Scale 3 mode: the maximum value of fHCLK is 120 MHz. */ -#endif /* STM32F405xx || STM32F407xx || STM32F415xx || STM32F417xx */ -/** - * @} - */ -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F446xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ - defined(STM32F412Rx) || defined(STM32F412Cx) -/** @defgroup PWREx_WakeUp_Pins PWREx WakeUp Pins - * @{ - */ -#define PWR_WAKEUP_PIN2 ((uint32_t)0x00000080U) -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ - defined(STM32F412Rx) || defined(STM32F412Cx) -#define PWR_WAKEUP_PIN3 ((uint32_t)0x00000040U) -#endif /* STM32F410xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Zx || STM32F412Vx || \ - STM32F412Rx || STM32F412Cx */ -/** - * @} - */ -#endif /* STM32F410xx || STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -/** - * @} - */ - -/* Exported macro ------------------------------------------------------------*/ -/** @defgroup PWREx_Exported_Constants PWREx Exported Constants - * @{ - */ - -#if defined(STM32F405xx) || defined(STM32F407xx) || defined(STM32F415xx) || defined(STM32F417xx) -/** @brief macros configure the main internal regulator output voltage. - * @param __REGULATOR__: specifies the regulator output voltage to achieve - * a tradeoff between performance and power consumption when the device does - * not operate at the maximum frequency (refer to the datasheets for more details). - * This parameter can be one of the following values: - * @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode - * @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode - * @retval None - */ -#define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) do { \ - __IO uint32_t tmpreg = 0x00U; \ - MODIFY_REG(PWR->CR, PWR_CR_VOS, (__REGULATOR__)); \ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(PWR->CR, PWR_CR_VOS); \ - UNUSED(tmpreg); \ - } while(0) -#else -/** @brief macros configure the main internal regulator output voltage. - * @param __REGULATOR__: specifies the regulator output voltage to achieve - * a tradeoff between performance and power consumption when the device does - * not operate at the maximum frequency (refer to the datasheets for more details). - * This parameter can be one of the following values: - * @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode - * @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode - * @arg PWR_REGULATOR_VOLTAGE_SCALE3: Regulator voltage output Scale 3 mode - * @retval None - */ -#define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) do { \ - __IO uint32_t tmpreg = 0x00U; \ - MODIFY_REG(PWR->CR, PWR_CR_VOS, (__REGULATOR__)); \ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(PWR->CR, PWR_CR_VOS); \ - UNUSED(tmpreg); \ - } while(0) -#endif /* STM32F405xx || STM32F407xx || STM32F415xx || STM32F417xx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) -/** @brief Macros to enable or disable the Over drive mode. - * @note These macros can be used only for STM32F42xx/STM3243xx devices. - */ -#define __HAL_PWR_OVERDRIVE_ENABLE() (*(__IO uint32_t *) CR_ODEN_BB = ENABLE) -#define __HAL_PWR_OVERDRIVE_DISABLE() (*(__IO uint32_t *) CR_ODEN_BB = DISABLE) - -/** @brief Macros to enable or disable the Over drive switching. - * @note These macros can be used only for STM32F42xx/STM3243xx devices. - */ -#define __HAL_PWR_OVERDRIVESWITCHING_ENABLE() (*(__IO uint32_t *) CR_ODSWEN_BB = ENABLE) -#define __HAL_PWR_OVERDRIVESWITCHING_DISABLE() (*(__IO uint32_t *) CR_ODSWEN_BB = DISABLE) - -/** @brief Macros to enable or disable the Under drive mode. - * @note This mode is enabled only with STOP low power mode. - * In this mode, the 1.2V domain is preserved in reduced leakage mode. This - * mode is only available when the main regulator or the low power regulator - * is in low voltage mode. - * @note If the Under-drive mode was enabled, it is automatically disabled after - * exiting Stop mode. - * When the voltage regulator operates in Under-drive mode, an additional - * startup delay is induced when waking up from Stop mode. - */ -#define __HAL_PWR_UNDERDRIVE_ENABLE() (PWR->CR |= (uint32_t)PWR_CR_UDEN) -#define __HAL_PWR_UNDERDRIVE_DISABLE() (PWR->CR &= (uint32_t)(~PWR_CR_UDEN)) - -/** @brief Check PWR flag is set or not. - * @note These macros can be used only for STM32F42xx/STM3243xx devices. - * @param __FLAG__: specifies the flag to check. - * This parameter can be one of the following values: - * @arg PWR_FLAG_ODRDY: This flag indicates that the Over-drive mode - * is ready - * @arg PWR_FLAG_ODSWRDY: This flag indicates that the Over-drive mode - * switching is ready - * @arg PWR_FLAG_UDRDY: This flag indicates that the Under-drive mode - * is enabled in Stop mode - * @retval The new state of __FLAG__ (TRUE or FALSE). - */ -#define __HAL_PWR_GET_ODRUDR_FLAG(__FLAG__) ((PWR->CSR & (__FLAG__)) == (__FLAG__)) - -/** @brief Clear the Under-Drive Ready flag. - * @note These macros can be used only for STM32F42xx/STM3243xx devices. - */ -#define __HAL_PWR_CLEAR_ODRUDR_FLAG() (PWR->CSR |= PWR_FLAG_UDRDY) - -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */ -/** - * @} - */ - -/* Exported functions --------------------------------------------------------*/ -/** @addtogroup PWREx_Exported_Functions PWREx Exported Functions - * @{ - */ - -/** @addtogroup PWREx_Exported_Functions_Group1 - * @{ - */ -void HAL_PWREx_EnableFlashPowerDown(void); -void HAL_PWREx_DisableFlashPowerDown(void); -HAL_StatusTypeDef HAL_PWREx_EnableBkUpReg(void); -HAL_StatusTypeDef HAL_PWREx_DisableBkUpReg(void); -uint32_t HAL_PWREx_GetVoltageRange(void); -HAL_StatusTypeDef HAL_PWREx_ControlVoltageScaling(uint32_t VoltageScaling); - -#if defined(STM32F469xx) || defined(STM32F479xx) -void HAL_PWREx_EnableWakeUpPinPolarityRisingEdge(void); -void HAL_PWREx_EnableWakeUpPinPolarityFallingEdge(void); -#endif /* STM32F469xx || STM32F479xx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F401xC) ||\ - defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F412Zx) || defined(STM32F412Vx) ||\ - defined(STM32F412Rx) || defined(STM32F412Cx) -void HAL_PWREx_EnableMainRegulatorLowVoltage(void); -void HAL_PWREx_DisableMainRegulatorLowVoltage(void); -void HAL_PWREx_EnableLowRegulatorLowVoltage(void); -void HAL_PWREx_DisableLowRegulatorLowVoltage(void); -#endif /* STM32F410xx || STM32F401xC || STM32F401xE || STM32F411xE || STM32F412Zx || STM32F412Vx ||\ - STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx) ||\ - defined(STM32F469xx) || defined(STM32F479xx) -HAL_StatusTypeDef HAL_PWREx_EnableOverDrive(void); -HAL_StatusTypeDef HAL_PWREx_DisableOverDrive(void); -HAL_StatusTypeDef HAL_PWREx_EnterUnderDriveSTOPMode(uint32_t Regulator, uint8_t STOPEntry); -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */ - -/** - * @} - */ - -/** - * @} - */ -/* Private types -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/* Private constants ---------------------------------------------------------*/ -/** @defgroup PWREx_Private_Constants PWREx Private Constants - * @{ - */ - -/** @defgroup PWREx_register_alias_address PWREx Register alias address - * @{ - */ -/* ------------- PWR registers bit address in the alias region ---------------*/ -/* --- CR Register ---*/ -/* Alias word address of FPDS bit */ -#define FPDS_BIT_NUMBER POSITION_VAL(PWR_CR_FPDS) -#define CR_FPDS_BB (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (FPDS_BIT_NUMBER * 4U)) - -/* Alias word address of ODEN bit */ -#define ODEN_BIT_NUMBER POSITION_VAL(PWR_CR_ODEN) -#define CR_ODEN_BB (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (ODEN_BIT_NUMBER * 4U)) - -/* Alias word address of ODSWEN bit */ -#define ODSWEN_BIT_NUMBER POSITION_VAL(PWR_CR_ODSWEN) -#define CR_ODSWEN_BB (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (ODSWEN_BIT_NUMBER * 4U)) - -/* Alias word address of MRLVDS bit */ -#define MRLVDS_BIT_NUMBER POSITION_VAL(PWR_CR_MRLVDS) -#define CR_MRLVDS_BB (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (MRLVDS_BIT_NUMBER * 4U)) - -/* Alias word address of LPLVDS bit */ -#define LPLVDS_BIT_NUMBER POSITION_VAL(PWR_CR_LPLVDS) -#define CR_LPLVDS_BB (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (LPLVDS_BIT_NUMBER * 4U)) - -/** - * @} - */ - -/** @defgroup PWREx_CSR_register_alias PWRx CSR Register alias address - * @{ - */ -/* --- CSR Register ---*/ -/* Alias word address of BRE bit */ -#define BRE_BIT_NUMBER POSITION_VAL(PWR_CSR_BRE) -#define CSR_BRE_BB (uint32_t)(PERIPH_BB_BASE + (PWR_CSR_OFFSET_BB * 32U) + (BRE_BIT_NUMBER * 4U)) - -#if defined(STM32F469xx) || defined(STM32F479xx) -/* Alias word address of WUPP bit */ -#define WUPP_BIT_NUMBER POSITION_VAL(PWR_CSR_WUPP) -#define CSR_WUPP_BB (PERIPH_BB_BASE + (PWR_CSR_OFFSET_BB * 32U) + (WUPP_BIT_NUMBER * 4U)) -#endif /* STM32F469xx || STM32F479xx */ -/** - * @} - */ - -/** - * @} - */ - -/* Private macros ------------------------------------------------------------*/ -/** @defgroup PWREx_Private_Macros PWREx Private Macros - * @{ - */ - -/** @defgroup PWREx_IS_PWR_Definitions PWREx Private macros to check input parameters - * @{ - */ -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) -#define IS_PWR_REGULATOR_UNDERDRIVE(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_UNDERDRIVE_ON) || \ - ((REGULATOR) == PWR_LOWPOWERREGULATOR_UNDERDRIVE_ON)) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F405xx) || defined(STM32F407xx) || defined(STM32F415xx) || defined(STM32F417xx) -#define IS_PWR_VOLTAGE_SCALING_RANGE(VOLTAGE) (((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \ - ((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE2)) -#else -#define IS_PWR_VOLTAGE_SCALING_RANGE(VOLTAGE) (((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \ - ((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE2) || \ - ((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE3)) -#endif /* STM32F405xx || STM32F407xx || STM32F415xx || STM32F417xx */ - -#if defined(STM32F446xx) -#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || ((PIN) == PWR_WAKEUP_PIN2)) -#elif defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ - defined(STM32F412Rx) || defined(STM32F412Cx) -#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || ((PIN) == PWR_WAKEUP_PIN2) || \ - ((PIN) == PWR_WAKEUP_PIN3)) -#else -#define IS_PWR_WAKEUP_PIN(PIN) ((PIN) == PWR_WAKEUP_PIN1) -#endif /* STM32F446xx */ -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -#ifdef __cplusplus -} -#endif - - -#endif /* __STM32F4xx_HAL_PWR_EX_H */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc.h b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc.h deleted file mode 100644 index 4754e60e..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc.h +++ /dev/null @@ -1,1424 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_rcc.h - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Header file of RCC HAL module. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_RCC_H -#define __STM32F4xx_HAL_RCC_H - -#ifdef __cplusplus -extern "C" { -#endif - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_def.h" - -/* Include RCC HAL Extended module */ -/* (include on top of file since RCC structures are defined in extended file) */ -#include "stm32f4xx_hal_rcc_ex.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @addtogroup RCC - * @{ - */ - -/* Exported types ------------------------------------------------------------*/ -/** @defgroup RCC_Exported_Types RCC Exported Types - * @{ - */ - -/** - * @brief RCC Internal/External Oscillator (HSE, HSI, LSE and LSI) configuration structure definition - */ -typedef struct -{ - uint32_t OscillatorType; /*!< The oscillators to be configured. - This parameter can be a value of @ref RCC_Oscillator_Type */ - - uint32_t HSEState; /*!< The new state of the HSE. - This parameter can be a value of @ref RCC_HSE_Config */ - - uint32_t LSEState; /*!< The new state of the LSE. - This parameter can be a value of @ref RCC_LSE_Config */ - - uint32_t HSIState; /*!< The new state of the HSI. - This parameter can be a value of @ref RCC_HSI_Config */ - - uint32_t HSICalibrationValue; /*!< The HSI calibration trimming value (default is RCC_HSICALIBRATION_DEFAULT). - This parameter must be a number between Min_Data = 0x00 and Max_Data = 0x1F */ - - uint32_t LSIState; /*!< The new state of the LSI. - This parameter can be a value of @ref RCC_LSI_Config */ - - RCC_PLLInitTypeDef PLL; /*!< PLL structure parameters */ -} RCC_OscInitTypeDef; - -/** - * @brief RCC System, AHB and APB busses clock configuration structure definition - */ -typedef struct -{ - uint32_t ClockType; /*!< The clock to be configured. - This parameter can be a value of @ref RCC_System_Clock_Type */ - - uint32_t SYSCLKSource; /*!< The clock source (SYSCLKS) used as system clock. - This parameter can be a value of @ref RCC_System_Clock_Source */ - - uint32_t AHBCLKDivider; /*!< The AHB clock (HCLK) divider. This clock is derived from the system clock (SYSCLK). - This parameter can be a value of @ref RCC_AHB_Clock_Source */ - - uint32_t APB1CLKDivider; /*!< The APB1 clock (PCLK1) divider. This clock is derived from the AHB clock (HCLK). - This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */ - - uint32_t APB2CLKDivider; /*!< The APB2 clock (PCLK2) divider. This clock is derived from the AHB clock (HCLK). - This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */ - -} RCC_ClkInitTypeDef; - -/** - * @} - */ - -/* Exported constants --------------------------------------------------------*/ -/** @defgroup RCC_Exported_Constants RCC Exported Constants - * @{ - */ - -/** @defgroup RCC_Oscillator_Type Oscillator Type - * @{ - */ -#define RCC_OSCILLATORTYPE_NONE ((uint32_t)0x00000000U) -#define RCC_OSCILLATORTYPE_HSE ((uint32_t)0x00000001U) -#define RCC_OSCILLATORTYPE_HSI ((uint32_t)0x00000002U) -#define RCC_OSCILLATORTYPE_LSE ((uint32_t)0x00000004U) -#define RCC_OSCILLATORTYPE_LSI ((uint32_t)0x00000008U) -/** - * @} - */ - -/** @defgroup RCC_HSE_Config HSE Config - * @{ - */ -#define RCC_HSE_OFF ((uint8_t)0x00U) -#define RCC_HSE_ON ((uint8_t)0x01U) -#define RCC_HSE_BYPASS ((uint8_t)0x05U) -/** - * @} - */ - -/** @defgroup RCC_LSE_Config LSE Config - * @{ - */ -#define RCC_LSE_OFF ((uint8_t)0x00U) -#define RCC_LSE_ON ((uint8_t)0x01U) -#define RCC_LSE_BYPASS ((uint8_t)0x05U) -/** - * @} - */ - -/** @defgroup RCC_HSI_Config HSI Config - * @{ - */ -#define RCC_HSI_OFF ((uint8_t)0x00U) -#define RCC_HSI_ON ((uint8_t)0x01U) - -#define RCC_HSICALIBRATION_DEFAULT ((uint32_t)0x10U) /* Default HSI calibration trimming value */ -/** - * @} - */ - -/** @defgroup RCC_LSI_Config LSI Config - * @{ - */ -#define RCC_LSI_OFF ((uint8_t)0x00U) -#define RCC_LSI_ON ((uint8_t)0x01U) -/** - * @} - */ - -/** @defgroup RCC_PLL_Config PLL Config - * @{ - */ -#define RCC_PLL_NONE ((uint8_t)0x00U) -#define RCC_PLL_OFF ((uint8_t)0x01U) -#define RCC_PLL_ON ((uint8_t)0x02U) -/** - * @} - */ - -/** @defgroup RCC_PLLP_Clock_Divider PLLP Clock Divider - * @{ - */ -#define RCC_PLLP_DIV2 ((uint32_t)0x00000002U) -#define RCC_PLLP_DIV4 ((uint32_t)0x00000004U) -#define RCC_PLLP_DIV6 ((uint32_t)0x00000006U) -#define RCC_PLLP_DIV8 ((uint32_t)0x00000008U) -/** - * @} - */ - -/** @defgroup RCC_PLL_Clock_Source PLL Clock Source - * @{ - */ -#define RCC_PLLSOURCE_HSI RCC_PLLCFGR_PLLSRC_HSI -#define RCC_PLLSOURCE_HSE RCC_PLLCFGR_PLLSRC_HSE -/** - * @} - */ - -/** @defgroup RCC_System_Clock_Type System Clock Type - * @{ - */ -#define RCC_CLOCKTYPE_SYSCLK ((uint32_t)0x00000001U) -#define RCC_CLOCKTYPE_HCLK ((uint32_t)0x00000002U) -#define RCC_CLOCKTYPE_PCLK1 ((uint32_t)0x00000004U) -#define RCC_CLOCKTYPE_PCLK2 ((uint32_t)0x00000008U) -/** - * @} - */ - -/** @defgroup RCC_System_Clock_Source System Clock Source - * @{ - */ -#define RCC_SYSCLKSOURCE_HSI RCC_CFGR_SW_HSI -#define RCC_SYSCLKSOURCE_HSE RCC_CFGR_SW_HSE -#define RCC_SYSCLKSOURCE_PLLCLK RCC_CFGR_SW_PLL -#define RCC_SYSCLKSOURCE_PLLRCLK ((uint32_t)(RCC_CFGR_SW_0 | RCC_CFGR_SW_1)) -/** - * @} - */ - -/** @defgroup RCC_System_Clock_Source_Status System Clock Source Status - * @{ - */ -#define RCC_SYSCLKSOURCE_STATUS_HSI RCC_CFGR_SWS_HSI /*!< HSI used as system clock */ -#define RCC_SYSCLKSOURCE_STATUS_HSE RCC_CFGR_SWS_HSE /*!< HSE used as system clock */ -#define RCC_SYSCLKSOURCE_STATUS_PLLCLK RCC_CFGR_SWS_PLL /*!< PLL used as system clock */ -#define RCC_SYSCLKSOURCE_STATUS_PLLRCLK ((uint32_t)(RCC_CFGR_SWS_0 | RCC_CFGR_SWS_1)) /*!< PLLR used as system clock */ -/** - * @} - */ - -/** @defgroup RCC_AHB_Clock_Source AHB Clock Source - * @{ - */ -#define RCC_SYSCLK_DIV1 RCC_CFGR_HPRE_DIV1 -#define RCC_SYSCLK_DIV2 RCC_CFGR_HPRE_DIV2 -#define RCC_SYSCLK_DIV4 RCC_CFGR_HPRE_DIV4 -#define RCC_SYSCLK_DIV8 RCC_CFGR_HPRE_DIV8 -#define RCC_SYSCLK_DIV16 RCC_CFGR_HPRE_DIV16 -#define RCC_SYSCLK_DIV64 RCC_CFGR_HPRE_DIV64 -#define RCC_SYSCLK_DIV128 RCC_CFGR_HPRE_DIV128 -#define RCC_SYSCLK_DIV256 RCC_CFGR_HPRE_DIV256 -#define RCC_SYSCLK_DIV512 RCC_CFGR_HPRE_DIV512 -/** - * @} - */ - -/** @defgroup RCC_APB1_APB2_Clock_Source APB1/APB2 Clock Source - * @{ - */ -#define RCC_HCLK_DIV1 RCC_CFGR_PPRE1_DIV1 -#define RCC_HCLK_DIV2 RCC_CFGR_PPRE1_DIV2 -#define RCC_HCLK_DIV4 RCC_CFGR_PPRE1_DIV4 -#define RCC_HCLK_DIV8 RCC_CFGR_PPRE1_DIV8 -#define RCC_HCLK_DIV16 RCC_CFGR_PPRE1_DIV16 -/** - * @} - */ - -/** @defgroup RCC_RTC_Clock_Source RTC Clock Source - * @{ - */ -#define RCC_RTCCLKSOURCE_LSE ((uint32_t)0x00000100U) -#define RCC_RTCCLKSOURCE_LSI ((uint32_t)0x00000200U) -#define RCC_RTCCLKSOURCE_HSE_DIV2 ((uint32_t)0x00020300U) -#define RCC_RTCCLKSOURCE_HSE_DIV3 ((uint32_t)0x00030300U) -#define RCC_RTCCLKSOURCE_HSE_DIV4 ((uint32_t)0x00040300U) -#define RCC_RTCCLKSOURCE_HSE_DIV5 ((uint32_t)0x00050300U) -#define RCC_RTCCLKSOURCE_HSE_DIV6 ((uint32_t)0x00060300U) -#define RCC_RTCCLKSOURCE_HSE_DIV7 ((uint32_t)0x00070300U) -#define RCC_RTCCLKSOURCE_HSE_DIV8 ((uint32_t)0x00080300U) -#define RCC_RTCCLKSOURCE_HSE_DIV9 ((uint32_t)0x00090300U) -#define RCC_RTCCLKSOURCE_HSE_DIV10 ((uint32_t)0x000A0300U) -#define RCC_RTCCLKSOURCE_HSE_DIV11 ((uint32_t)0x000B0300U) -#define RCC_RTCCLKSOURCE_HSE_DIV12 ((uint32_t)0x000C0300U) -#define RCC_RTCCLKSOURCE_HSE_DIV13 ((uint32_t)0x000D0300U) -#define RCC_RTCCLKSOURCE_HSE_DIV14 ((uint32_t)0x000E0300U) -#define RCC_RTCCLKSOURCE_HSE_DIV15 ((uint32_t)0x000F0300U) -#define RCC_RTCCLKSOURCE_HSE_DIV16 ((uint32_t)0x00100300U) -#define RCC_RTCCLKSOURCE_HSE_DIV17 ((uint32_t)0x00110300U) -#define RCC_RTCCLKSOURCE_HSE_DIV18 ((uint32_t)0x00120300U) -#define RCC_RTCCLKSOURCE_HSE_DIV19 ((uint32_t)0x00130300U) -#define RCC_RTCCLKSOURCE_HSE_DIV20 ((uint32_t)0x00140300U) -#define RCC_RTCCLKSOURCE_HSE_DIV21 ((uint32_t)0x00150300U) -#define RCC_RTCCLKSOURCE_HSE_DIV22 ((uint32_t)0x00160300U) -#define RCC_RTCCLKSOURCE_HSE_DIV23 ((uint32_t)0x00170300U) -#define RCC_RTCCLKSOURCE_HSE_DIV24 ((uint32_t)0x00180300U) -#define RCC_RTCCLKSOURCE_HSE_DIV25 ((uint32_t)0x00190300U) -#define RCC_RTCCLKSOURCE_HSE_DIV26 ((uint32_t)0x001A0300U) -#define RCC_RTCCLKSOURCE_HSE_DIV27 ((uint32_t)0x001B0300U) -#define RCC_RTCCLKSOURCE_HSE_DIV28 ((uint32_t)0x001C0300U) -#define RCC_RTCCLKSOURCE_HSE_DIV29 ((uint32_t)0x001D0300U) -#define RCC_RTCCLKSOURCE_HSE_DIV30 ((uint32_t)0x001E0300U) -#define RCC_RTCCLKSOURCE_HSE_DIV31 ((uint32_t)0x001F0300U) -/** - * @} - */ - -/** @defgroup RCC_MCO_Index MCO Index - * @{ - */ -#define RCC_MCO1 ((uint32_t)0x00000000U) -#define RCC_MCO2 ((uint32_t)0x00000001U) -/** - * @} - */ - -/** @defgroup RCC_MCO1_Clock_Source MCO1 Clock Source - * @{ - */ -#define RCC_MCO1SOURCE_HSI ((uint32_t)0x00000000U) -#define RCC_MCO1SOURCE_LSE RCC_CFGR_MCO1_0 -#define RCC_MCO1SOURCE_HSE RCC_CFGR_MCO1_1 -#define RCC_MCO1SOURCE_PLLCLK RCC_CFGR_MCO1 -/** - * @} - */ - -/** @defgroup RCC_MCOx_Clock_Prescaler MCOx Clock Prescaler - * @{ - */ -#define RCC_MCODIV_1 ((uint32_t)0x00000000U) -#define RCC_MCODIV_2 RCC_CFGR_MCO1PRE_2 -#define RCC_MCODIV_3 ((uint32_t)RCC_CFGR_MCO1PRE_0 | RCC_CFGR_MCO1PRE_2) -#define RCC_MCODIV_4 ((uint32_t)RCC_CFGR_MCO1PRE_1 | RCC_CFGR_MCO1PRE_2) -#define RCC_MCODIV_5 RCC_CFGR_MCO1PRE -/** - * @} - */ - -/** @defgroup RCC_Interrupt Interrupts - * @{ - */ -#define RCC_IT_LSIRDY ((uint8_t)0x01U) -#define RCC_IT_LSERDY ((uint8_t)0x02U) -#define RCC_IT_HSIRDY ((uint8_t)0x04U) -#define RCC_IT_HSERDY ((uint8_t)0x08U) -#define RCC_IT_PLLRDY ((uint8_t)0x10U) -#define RCC_IT_PLLI2SRDY ((uint8_t)0x20U) -#define RCC_IT_CSS ((uint8_t)0x80U) -/** - * @} - */ - -/** @defgroup RCC_Flag Flags - * Elements values convention: 0XXYYYYYb - * - YYYYY : Flag position in the register - * - 0XX : Register index - * - 01: CR register - * - 10: BDCR register - * - 11: CSR register - * @{ - */ -/* Flags in the CR register */ -#define RCC_FLAG_HSIRDY ((uint8_t)0x21U) -#define RCC_FLAG_HSERDY ((uint8_t)0x31U) -#define RCC_FLAG_PLLRDY ((uint8_t)0x39U) -#define RCC_FLAG_PLLI2SRDY ((uint8_t)0x3BU) - -/* Flags in the BDCR register */ -#define RCC_FLAG_LSERDY ((uint8_t)0x41U) - -/* Flags in the CSR register */ -#define RCC_FLAG_LSIRDY ((uint8_t)0x61U) -#define RCC_FLAG_BORRST ((uint8_t)0x79U) -#define RCC_FLAG_PINRST ((uint8_t)0x7AU) -#define RCC_FLAG_PORRST ((uint8_t)0x7BU) -#define RCC_FLAG_SFTRST ((uint8_t)0x7CU) -#define RCC_FLAG_IWDGRST ((uint8_t)0x7DU) -#define RCC_FLAG_WWDGRST ((uint8_t)0x7EU) -#define RCC_FLAG_LPWRRST ((uint8_t)0x7FU) -/** - * @} - */ - -/** - * @} - */ - -/* Exported macro ------------------------------------------------------------*/ -/** @defgroup RCC_Exported_Macros RCC Exported Macros - * @{ - */ - -/** @defgroup RCC_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable - * @brief Enable or disable the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_GPIOA_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOAEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOAEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOB_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOBEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOBEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOH_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOHEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOHEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_DMA1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_DMA2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN);\ - UNUSED(tmpreg); \ - } while(0) - -#define __HAL_RCC_GPIOA_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOAEN)) -#define __HAL_RCC_GPIOB_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOBEN)) -#define __HAL_RCC_GPIOC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOCEN)) -#define __HAL_RCC_GPIOH_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOHEN)) -#define __HAL_RCC_DMA1_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_DMA1EN)) -#define __HAL_RCC_DMA2_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_DMA2EN)) -/** - * @} - */ - -/** @defgroup RCC_AHB1_Peripheral_Clock_Enable_Disable_Status AHB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_GPIOA_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOAEN)) != RESET) -#define __HAL_RCC_GPIOB_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOBEN)) != RESET) -#define __HAL_RCC_GPIOC_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOCEN)) != RESET) -#define __HAL_RCC_GPIOH_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOHEN)) != RESET) -#define __HAL_RCC_DMA1_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_DMA1EN)) != RESET) -#define __HAL_RCC_DMA2_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_DMA2EN)) != RESET) - -#define __HAL_RCC_GPIOA_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOAEN)) == RESET) -#define __HAL_RCC_GPIOB_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOBEN)) == RESET) -#define __HAL_RCC_GPIOC_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOCEN)) == RESET) -#define __HAL_RCC_GPIOH_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOHEN)) == RESET) -#define __HAL_RCC_DMA1_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_DMA1EN)) == RESET) -#define __HAL_RCC_DMA2_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_DMA2EN)) == RESET) -/** - * @} - */ - -/** @defgroup RCC_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable - * @brief Enable or disable the Low Speed APB (APB1) peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM5_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM5EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM5EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_WWDG_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_USART2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_USART2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_USART2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_I2C1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_I2C2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_PWR_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\ - UNUSED(tmpreg); \ - } while(0) - -#define __HAL_RCC_TIM5_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM5EN)) -#define __HAL_RCC_WWDG_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_WWDGEN)) -#define __HAL_RCC_SPI2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI2EN)) -#define __HAL_RCC_USART2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_USART2EN)) -#define __HAL_RCC_I2C1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C1EN)) -#define __HAL_RCC_I2C2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C2EN)) -#define __HAL_RCC_PWR_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_PWREN)) -/** - * @} - */ - -/** @defgroup RCC_APB1_Peripheral_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM5_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM5EN)) != RESET) -#define __HAL_RCC_WWDG_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_WWDGEN)) != RESET) -#define __HAL_RCC_SPI2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI2EN)) != RESET) -#define __HAL_RCC_USART2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART2EN)) != RESET) -#define __HAL_RCC_I2C1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C1EN)) != RESET) -#define __HAL_RCC_I2C2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C2EN)) != RESET) -#define __HAL_RCC_PWR_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_PWREN)) != RESET) - -#define __HAL_RCC_TIM5_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM5EN)) == RESET) -#define __HAL_RCC_WWDG_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_WWDGEN)) == RESET) -#define __HAL_RCC_SPI2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI2EN)) == RESET) -#define __HAL_RCC_USART2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART2EN)) == RESET) -#define __HAL_RCC_I2C1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C1EN)) == RESET) -#define __HAL_RCC_I2C2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C2EN)) == RESET) -#define __HAL_RCC_PWR_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_PWREN)) == RESET) -/** - * @} - */ - -/** @defgroup RCC_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable - * @brief Enable or disable the High Speed APB (APB2) peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_USART1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_USART6_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_USART6EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART6EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_ADC1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SYSCFG_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM9_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM9EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM9EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM11_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM11EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM11EN);\ - UNUSED(tmpreg); \ - } while(0) - -#define __HAL_RCC_TIM1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM1EN)) -#define __HAL_RCC_USART1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_USART1EN)) -#define __HAL_RCC_USART6_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_USART6EN)) -#define __HAL_RCC_ADC1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC1EN)) -#define __HAL_RCC_SPI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI1EN)) -#define __HAL_RCC_SYSCFG_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SYSCFGEN)) -#define __HAL_RCC_TIM9_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM9EN)) -#define __HAL_RCC_TIM11_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM11EN)) -/** - * @} - */ - -/** @defgroup RCC_APB2_Peripheral_Clock_Enable_Disable_Status APB2 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM1EN)) != RESET) -#define __HAL_RCC_USART1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART1EN)) != RESET) -#define __HAL_RCC_USART6_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART6EN)) != RESET) -#define __HAL_RCC_ADC1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC1EN)) != RESET) -#define __HAL_RCC_SPI1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI1EN)) != RESET) -#define __HAL_RCC_SYSCFG_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SYSCFGEN)) != RESET) -#define __HAL_RCC_TIM9_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM9EN)) != RESET) -#define __HAL_RCC_TIM11_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM11EN)) != RESET) - -#define __HAL_RCC_TIM1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM1EN)) == RESET) -#define __HAL_RCC_USART1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART1EN)) == RESET) -#define __HAL_RCC_USART6_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART6EN)) == RESET) -#define __HAL_RCC_ADC1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC1EN)) == RESET) -#define __HAL_RCC_SPI1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI1EN)) == RESET) -#define __HAL_RCC_SYSCFG_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SYSCFGEN)) == RESET) -#define __HAL_RCC_TIM9_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM9EN)) == RESET) -#define __HAL_RCC_TIM11_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM11EN)) == RESET) -/** - * @} - */ - -/** @defgroup RCC_AHB1_Force_Release_Reset AHB1 Force Release Reset - * @brief Force or release AHB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_AHB1_FORCE_RESET() (RCC->AHB1RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_GPIOA_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOARST)) -#define __HAL_RCC_GPIOB_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOBRST)) -#define __HAL_RCC_GPIOC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOCRST)) -#define __HAL_RCC_GPIOH_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOHRST)) -#define __HAL_RCC_DMA1_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_DMA1RST)) -#define __HAL_RCC_DMA2_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_DMA2RST)) - -#define __HAL_RCC_AHB1_RELEASE_RESET() (RCC->AHB1RSTR = 0x00U) -#define __HAL_RCC_GPIOA_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOARST)) -#define __HAL_RCC_GPIOB_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOBRST)) -#define __HAL_RCC_GPIOC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOCRST)) -#define __HAL_RCC_GPIOH_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOHRST)) -#define __HAL_RCC_DMA1_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_DMA1RST)) -#define __HAL_RCC_DMA2_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_DMA2RST)) -/** - * @} - */ - -/** @defgroup RCC_APB1_Force_Release_Reset APB1 Force Release Reset - * @brief Force or release APB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_APB1_FORCE_RESET() (RCC->APB1RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_TIM5_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM5RST)) -#define __HAL_RCC_WWDG_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_WWDGRST)) -#define __HAL_RCC_SPI2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI2RST)) -#define __HAL_RCC_USART2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USART2RST)) -#define __HAL_RCC_I2C1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C1RST)) -#define __HAL_RCC_I2C2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C2RST)) -#define __HAL_RCC_PWR_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_PWRRST)) - -#define __HAL_RCC_APB1_RELEASE_RESET() (RCC->APB1RSTR = 0x00U) -#define __HAL_RCC_TIM5_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM5RST)) -#define __HAL_RCC_WWDG_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_WWDGRST)) -#define __HAL_RCC_SPI2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI2RST)) -#define __HAL_RCC_USART2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_USART2RST)) -#define __HAL_RCC_I2C1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C1RST)) -#define __HAL_RCC_I2C2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C2RST)) -#define __HAL_RCC_PWR_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_PWRRST)) -/** - * @} - */ - -/** @defgroup RCC_APB2_Force_Release_Reset APB2 Force Release Reset - * @brief Force or release APB2 peripheral reset. - * @{ - */ -#define __HAL_RCC_APB2_FORCE_RESET() (RCC->APB2RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_TIM1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM1RST)) -#define __HAL_RCC_USART1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_USART1RST)) -#define __HAL_RCC_USART6_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_USART6RST)) -#define __HAL_RCC_ADC_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_ADCRST)) -#define __HAL_RCC_SPI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI1RST)) -#define __HAL_RCC_SYSCFG_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SYSCFGRST)) -#define __HAL_RCC_TIM9_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM9RST)) -#define __HAL_RCC_TIM11_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM11RST)) - -#define __HAL_RCC_APB2_RELEASE_RESET() (RCC->APB2RSTR = 0x00U) -#define __HAL_RCC_TIM1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM1RST)) -#define __HAL_RCC_USART1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_USART1RST)) -#define __HAL_RCC_USART6_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_USART6RST)) -#define __HAL_RCC_ADC_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_ADCRST)) -#define __HAL_RCC_SPI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI1RST)) -#define __HAL_RCC_SYSCFG_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SYSCFGRST)) -#define __HAL_RCC_TIM9_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM9RST)) -#define __HAL_RCC_TIM11_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM11RST)) -/** - * @} - */ - -/** @defgroup RCC_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_GPIOA_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOALPEN)) -#define __HAL_RCC_GPIOB_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOBLPEN)) -#define __HAL_RCC_GPIOC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOCLPEN)) -#define __HAL_RCC_GPIOH_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOHLPEN)) -#define __HAL_RCC_DMA1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_DMA1LPEN)) -#define __HAL_RCC_DMA2_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_DMA2LPEN)) - -#define __HAL_RCC_GPIOA_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOALPEN)) -#define __HAL_RCC_GPIOB_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOBLPEN)) -#define __HAL_RCC_GPIOC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOCLPEN)) -#define __HAL_RCC_GPIOH_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOHLPEN)) -#define __HAL_RCC_DMA1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_DMA1LPEN)) -#define __HAL_RCC_DMA2_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_DMA2LPEN)) -/** - * @} - */ - -/** @defgroup RCC_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_TIM5_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM5LPEN)) -#define __HAL_RCC_WWDG_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_WWDGLPEN)) -#define __HAL_RCC_SPI2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI2LPEN)) -#define __HAL_RCC_USART2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_USART2LPEN)) -#define __HAL_RCC_I2C1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C1LPEN)) -#define __HAL_RCC_I2C2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C2LPEN)) -#define __HAL_RCC_PWR_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_PWRLPEN)) - -#define __HAL_RCC_TIM5_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM5LPEN)) -#define __HAL_RCC_WWDG_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_WWDGLPEN)) -#define __HAL_RCC_SPI2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI2LPEN)) -#define __HAL_RCC_USART2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_USART2LPEN)) -#define __HAL_RCC_I2C1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C1LPEN)) -#define __HAL_RCC_I2C2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C2LPEN)) -#define __HAL_RCC_PWR_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_PWRLPEN)) -/** - * @} - */ - -/** @defgroup RCC_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_TIM1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM1LPEN)) -#define __HAL_RCC_USART1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_USART1LPEN)) -#define __HAL_RCC_USART6_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_USART6LPEN)) -#define __HAL_RCC_ADC1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC1LPEN)) -#define __HAL_RCC_SPI1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI1LPEN)) -#define __HAL_RCC_SYSCFG_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SYSCFGLPEN)) -#define __HAL_RCC_TIM9_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM9LPEN)) -#define __HAL_RCC_TIM11_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM11LPEN)) - -#define __HAL_RCC_TIM1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM1LPEN)) -#define __HAL_RCC_USART1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_USART1LPEN)) -#define __HAL_RCC_USART6_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_USART6LPEN)) -#define __HAL_RCC_ADC1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC1LPEN)) -#define __HAL_RCC_SPI1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI1LPEN)) -#define __HAL_RCC_SYSCFG_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SYSCFGLPEN)) -#define __HAL_RCC_TIM9_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM9LPEN)) -#define __HAL_RCC_TIM11_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM11LPEN)) -/** - * @} - */ - -/** @defgroup RCC_HSI_Configuration HSI Configuration - * @{ - */ - -/** @brief Macros to enable or disable the Internal High Speed oscillator (HSI). - * @note The HSI is stopped by hardware when entering STOP and STANDBY modes. - * It is used (enabled by hardware) as system clock source after startup - * from Reset, wake-up from STOP and STANDBY mode, or in case of failure - * of the HSE used directly or indirectly as system clock (if the Clock - * Security System CSS is enabled). - * @note HSI can not be stopped if it is used as system clock source. In this case, - * you have to select another source of the system clock then stop the HSI. - * @note After enabling the HSI, the application software should wait on HSIRDY - * flag to be set indicating that HSI clock is stable and can be used as - * system clock source. - * This parameter can be: ENABLE or DISABLE. - * @note When the HSI is stopped, HSIRDY flag goes low after 6 HSI oscillator - * clock cycles. - */ -#define __HAL_RCC_HSI_ENABLE() (*(__IO uint32_t *) RCC_CR_HSION_BB = ENABLE) -#define __HAL_RCC_HSI_DISABLE() (*(__IO uint32_t *) RCC_CR_HSION_BB = DISABLE) - -/** @brief Macro to adjust the Internal High Speed oscillator (HSI) calibration value. - * @note The calibration is used to compensate for the variations in voltage - * and temperature that influence the frequency of the internal HSI RC. - * @param __HSICalibrationValue__: specifies the calibration trimming value. - * (default is RCC_HSICALIBRATION_DEFAULT). - * This parameter must be a number between 0 and 0x1F. - */ -#define __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(__HSICalibrationValue__) (MODIFY_REG(RCC->CR,\ - RCC_CR_HSITRIM, (uint32_t)(__HSICalibrationValue__) << POSITION_VAL(RCC_CR_HSITRIM))) -/** - * @} - */ - -/** @defgroup RCC_LSI_Configuration LSI Configuration - * @{ - */ - -/** @brief Macros to enable or disable the Internal Low Speed oscillator (LSI). - * @note After enabling the LSI, the application software should wait on - * LSIRDY flag to be set indicating that LSI clock is stable and can - * be used to clock the IWDG and/or the RTC. - * @note LSI can not be disabled if the IWDG is running. - * @note When the LSI is stopped, LSIRDY flag goes low after 6 LSI oscillator - * clock cycles. - */ -#define __HAL_RCC_LSI_ENABLE() (*(__IO uint32_t *) RCC_CSR_LSION_BB = ENABLE) -#define __HAL_RCC_LSI_DISABLE() (*(__IO uint32_t *) RCC_CSR_LSION_BB = DISABLE) -/** - * @} - */ - -/** @defgroup RCC_HSE_Configuration HSE Configuration - * @{ - */ - -/** - * @brief Macro to configure the External High Speed oscillator (HSE). - * @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not supported by this macro. - * User should request a transition to HSE Off first and then HSE On or HSE Bypass. - * @note After enabling the HSE (RCC_HSE_ON or RCC_HSE_Bypass), the application - * software should wait on HSERDY flag to be set indicating that HSE clock - * is stable and can be used to clock the PLL and/or system clock. - * @note HSE state can not be changed if it is used directly or through the - * PLL as system clock. In this case, you have to select another source - * of the system clock then change the HSE state (ex. disable it). - * @note The HSE is stopped by hardware when entering STOP and STANDBY modes. - * @note This function reset the CSSON bit, so if the clock security system(CSS) - * was previously enabled you have to enable it again after calling this - * function. - * @param __STATE__: specifies the new state of the HSE. - * This parameter can be one of the following values: - * @arg RCC_HSE_OFF: turn OFF the HSE oscillator, HSERDY flag goes low after - * 6 HSE oscillator clock cycles. - * @arg RCC_HSE_ON: turn ON the HSE oscillator. - * @arg RCC_HSE_BYPASS: HSE oscillator bypassed with external clock. - */ -#define __HAL_RCC_HSE_CONFIG(__STATE__) (*(__IO uint8_t *) RCC_CR_BYTE2_ADDRESS = (__STATE__)) -/** - * @} - */ - -/** @defgroup RCC_LSE_Configuration LSE Configuration - * @{ - */ - -/** - * @brief Macro to configure the External Low Speed oscillator (LSE). - * @note Transition LSE Bypass to LSE On and LSE On to LSE Bypass are not supported by this macro. - * User should request a transition to LSE Off first and then LSE On or LSE Bypass. - * @note As the LSE is in the Backup domain and write access is denied to - * this domain after reset, you have to enable write access using - * HAL_PWR_EnableBkUpAccess() function before to configure the LSE - * (to be done once after reset). - * @note After enabling the LSE (RCC_LSE_ON or RCC_LSE_BYPASS), the application - * software should wait on LSERDY flag to be set indicating that LSE clock - * is stable and can be used to clock the RTC. - * @param __STATE__: specifies the new state of the LSE. - * This parameter can be one of the following values: - * @arg RCC_LSE_OFF: turn OFF the LSE oscillator, LSERDY flag goes low after - * 6 LSE oscillator clock cycles. - * @arg RCC_LSE_ON: turn ON the LSE oscillator. - * @arg RCC_LSE_BYPASS: LSE oscillator bypassed with external clock. - */ -#define __HAL_RCC_LSE_CONFIG(__STATE__) (*(__IO uint8_t *) RCC_BDCR_BYTE0_ADDRESS = (__STATE__)) - -/** - * @} - */ - -/** @defgroup RCC_Internal_RTC_Clock_Configuration RTC Clock Configuration - * @{ - */ - -/** @brief Macros to enable or disable the RTC clock. - * @note These macros must be used only after the RTC clock source was selected. - */ -#define __HAL_RCC_RTC_ENABLE() (*(__IO uint32_t *) RCC_BDCR_RTCEN_BB = ENABLE) -#define __HAL_RCC_RTC_DISABLE() (*(__IO uint32_t *) RCC_BDCR_RTCEN_BB = DISABLE) - -/** @brief Macros to configure the RTC clock (RTCCLK). - * @note As the RTC clock configuration bits are in the Backup domain and write - * access is denied to this domain after reset, you have to enable write - * access using the Power Backup Access macro before to configure - * the RTC clock source (to be done once after reset). - * @note Once the RTC clock is configured it can't be changed unless the - * Backup domain is reset using __HAL_RCC_BackupReset_RELEASE() macro, or by - * a Power On Reset (POR). - * @param __RTCCLKSource__: specifies the RTC clock source. - * This parameter can be one of the following values: - * @arg RCC_RTCCLKSOURCE_LSE: LSE selected as RTC clock. - * @arg RCC_RTCCLKSOURCE_LSI: LSI selected as RTC clock. - * @arg RCC_RTCCLKSOURCE_HSE_DIVx: HSE clock divided by x selected - * as RTC clock, where x:[2,31] - * @note If the LSE or LSI is used as RTC clock source, the RTC continues to - * work in STOP and STANDBY modes, and can be used as wake-up source. - * However, when the HSE clock is used as RTC clock source, the RTC - * cannot be used in STOP and STANDBY modes. - * @note The maximum input clock frequency for RTC is 1MHz (when using HSE as - * RTC clock source). - */ -#define __HAL_RCC_RTC_CLKPRESCALER(__RTCCLKSource__) (((__RTCCLKSource__) & RCC_BDCR_RTCSEL) == RCC_BDCR_RTCSEL) ? \ - MODIFY_REG(RCC->CFGR, RCC_CFGR_RTCPRE, ((__RTCCLKSource__) & 0xFFFFCFFU)) : CLEAR_BIT(RCC->CFGR, RCC_CFGR_RTCPRE) - -#define __HAL_RCC_RTC_CONFIG(__RTCCLKSource__) do { __HAL_RCC_RTC_CLKPRESCALER(__RTCCLKSource__); \ - RCC->BDCR |= ((__RTCCLKSource__) & 0x00000FFFU); \ - } while (0) - -/** @brief Macros to force or release the Backup domain reset. - * @note This function resets the RTC peripheral (including the backup registers) - * and the RTC clock source selection in RCC_CSR register. - * @note The BKPSRAM is not affected by this reset. - */ -#define __HAL_RCC_BACKUPRESET_FORCE() (*(__IO uint32_t *) RCC_BDCR_BDRST_BB = ENABLE) -#define __HAL_RCC_BACKUPRESET_RELEASE() (*(__IO uint32_t *) RCC_BDCR_BDRST_BB = DISABLE) -/** - * @} - */ - -/** @defgroup RCC_PLL_Configuration PLL Configuration - * @{ - */ - -/** @brief Macros to enable or disable the main PLL. - * @note After enabling the main PLL, the application software should wait on - * PLLRDY flag to be set indicating that PLL clock is stable and can - * be used as system clock source. - * @note The main PLL can not be disabled if it is used as system clock source - * @note The main PLL is disabled by hardware when entering STOP and STANDBY modes. - */ -#define __HAL_RCC_PLL_ENABLE() (*(__IO uint32_t *) RCC_CR_PLLON_BB = ENABLE) -#define __HAL_RCC_PLL_DISABLE() (*(__IO uint32_t *) RCC_CR_PLLON_BB = DISABLE) - -/** @brief Macro to configure the PLL clock source. - * @note This function must be used only when the main PLL is disabled. - * @param __PLLSOURCE__: specifies the PLL entry clock source. - * This parameter can be one of the following values: - * @arg RCC_PLLSOURCE_HSI: HSI oscillator clock selected as PLL clock entry - * @arg RCC_PLLSOURCE_HSE: HSE oscillator clock selected as PLL clock entry - * - */ -#define __HAL_RCC_PLL_PLLSOURCE_CONFIG(__PLLSOURCE__) MODIFY_REG(RCC->PLLCFGR, RCC_PLLCFGR_PLLSRC, (__PLLSOURCE__)) - -/** @brief Macro to configure the PLL multiplication factor. - * @note This function must be used only when the main PLL is disabled. - * @param __PLLM__: specifies the division factor for PLL VCO input clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 63. - * @note You have to set the PLLM parameter correctly to ensure that the VCO input - * frequency ranges from 1 to 2 MHz. It is recommended to select a frequency - * of 2 MHz to limit PLL jitter. - * - */ -#define __HAL_RCC_PLL_PLLM_CONFIG(__PLLM__) MODIFY_REG(RCC->PLLCFGR, RCC_PLLCFGR_PLLM, (__PLLM__)) -/** - * @} - */ - -/** @defgroup RCC_Get_Clock_source Get Clock source - * @{ - */ -/** - * @brief Macro to configure the system clock source. - * @param __RCC_SYSCLKSOURCE__: specifies the system clock source. - * This parameter can be one of the following values: - * - RCC_SYSCLKSOURCE_HSI: HSI oscillator is used as system clock source. - * - RCC_SYSCLKSOURCE_HSE: HSE oscillator is used as system clock source. - * - RCC_SYSCLKSOURCE_PLLCLK: PLL output is used as system clock source. - * - RCC_SYSCLKSOURCE_PLLRCLK: PLLR output is used as system clock source. - */ -#define __HAL_RCC_SYSCLK_CONFIG(__RCC_SYSCLKSOURCE__) MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, (__RCC_SYSCLKSOURCE__)) - -/** @brief Macro to get the clock source used as system clock. - * @retval The clock source used as system clock. The returned value can be one - * of the following: - * - RCC_SYSCLKSOURCE_STATUS_HSI: HSI used as system clock. - * - RCC_SYSCLKSOURCE_STATUS_HSE: HSE used as system clock. - * - RCC_SYSCLKSOURCE_STATUS_PLLCLK: PLL used as system clock. - * - RCC_SYSCLKSOURCE_STATUS_PLLRCLK: PLLR used as system clock. - */ -#define __HAL_RCC_GET_SYSCLK_SOURCE() ((uint32_t)(RCC->CFGR & RCC_CFGR_SWS)) - -/** @brief Macro to get the oscillator used as PLL clock source. - * @retval The oscillator used as PLL clock source. The returned value can be one - * of the following: - * - RCC_PLLSOURCE_HSI: HSI oscillator is used as PLL clock source. - * - RCC_PLLSOURCE_HSE: HSE oscillator is used as PLL clock source. - */ -#define __HAL_RCC_GET_PLL_OSCSOURCE() ((uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC)) -/** - * @} - */ - -/** @defgroup RCCEx_MCOx_Clock_Config RCC Extended MCOx Clock Config - * @{ - */ - -/** @brief Macro to configure the MCO1 clock. - * @param __MCOCLKSOURCE__ specifies the MCO clock source. - * This parameter can be one of the following values: - * @arg RCC_MCO1SOURCE_HSI: HSI clock selected as MCO1 source - * @arg RCC_MCO1SOURCE_LSE: LSE clock selected as MCO1 source - * @arg RCC_MCO1SOURCE_HSE: HSE clock selected as MCO1 source - * @arg RCC_MCO1SOURCE_PLLCLK: main PLL clock selected as MCO1 source - * @param __MCODIV__ specifies the MCO clock prescaler. - * This parameter can be one of the following values: - * @arg RCC_MCODIV_1: no division applied to MCOx clock - * @arg RCC_MCODIV_2: division by 2 applied to MCOx clock - * @arg RCC_MCODIV_3: division by 3 applied to MCOx clock - * @arg RCC_MCODIV_4: division by 4 applied to MCOx clock - * @arg RCC_MCODIV_5: division by 5 applied to MCOx clock - */ -#define __HAL_RCC_MCO1_CONFIG(__MCOCLKSOURCE__, __MCODIV__) \ - MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO1 | RCC_CFGR_MCO1PRE), ((__MCOCLKSOURCE__) | (__MCODIV__))) - -/** @brief Macro to configure the MCO2 clock. - * @param __MCOCLKSOURCE__ specifies the MCO clock source. - * This parameter can be one of the following values: - * @arg RCC_MCO2SOURCE_SYSCLK: System clock (SYSCLK) selected as MCO2 source - * @arg RCC_MCO2SOURCE_PLLI2SCLK: PLLI2S clock selected as MCO2 source, available for all STM32F4 devices except STM32F410xx - * @arg RCC_MCO2SOURCE_I2SCLK: I2SCLK clock selected as MCO2 source, available only for STM32F410Rx devices - * @arg RCC_MCO2SOURCE_HSE: HSE clock selected as MCO2 source - * @arg RCC_MCO2SOURCE_PLLCLK: main PLL clock selected as MCO2 source - * @param __MCODIV__ specifies the MCO clock prescaler. - * This parameter can be one of the following values: - * @arg RCC_MCODIV_1: no division applied to MCOx clock - * @arg RCC_MCODIV_2: division by 2 applied to MCOx clock - * @arg RCC_MCODIV_3: division by 3 applied to MCOx clock - * @arg RCC_MCODIV_4: division by 4 applied to MCOx clock - * @arg RCC_MCODIV_5: division by 5 applied to MCOx clock - * @note For STM32F410Rx devices, to output I2SCLK clock on MCO2, you should have - * at least one of the SPI clocks enabled (SPI1, SPI2 or SPI5). - */ -#define __HAL_RCC_MCO2_CONFIG(__MCOCLKSOURCE__, __MCODIV__) \ - MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO2 | RCC_CFGR_MCO2PRE), ((__MCOCLKSOURCE__) | ((__MCODIV__) << 3U))); -/** - * @} - */ - -/** @defgroup RCC_Flags_Interrupts_Management Flags Interrupts Management - * @brief macros to manage the specified RCC Flags and interrupts. - * @{ - */ - -/** @brief Enable RCC interrupt (Perform Byte access to RCC_CIR[14:8] bits to enable - * the selected interrupts). - * @param __INTERRUPT__: specifies the RCC interrupt sources to be enabled. - * This parameter can be any combination of the following values: - * @arg RCC_IT_LSIRDY: LSI ready interrupt. - * @arg RCC_IT_LSERDY: LSE ready interrupt. - * @arg RCC_IT_HSIRDY: HSI ready interrupt. - * @arg RCC_IT_HSERDY: HSE ready interrupt. - * @arg RCC_IT_PLLRDY: Main PLL ready interrupt. - * @arg RCC_IT_PLLI2SRDY: PLLI2S ready interrupt. - */ -#define __HAL_RCC_ENABLE_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE1_ADDRESS |= (__INTERRUPT__)) - -/** @brief Disable RCC interrupt (Perform Byte access to RCC_CIR[14:8] bits to disable - * the selected interrupts). - * @param __INTERRUPT__: specifies the RCC interrupt sources to be disabled. - * This parameter can be any combination of the following values: - * @arg RCC_IT_LSIRDY: LSI ready interrupt. - * @arg RCC_IT_LSERDY: LSE ready interrupt. - * @arg RCC_IT_HSIRDY: HSI ready interrupt. - * @arg RCC_IT_HSERDY: HSE ready interrupt. - * @arg RCC_IT_PLLRDY: Main PLL ready interrupt. - * @arg RCC_IT_PLLI2SRDY: PLLI2S ready interrupt. - */ -#define __HAL_RCC_DISABLE_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE1_ADDRESS &= (uint8_t)(~(__INTERRUPT__))) - -/** @brief Clear the RCC's interrupt pending bits (Perform Byte access to RCC_CIR[23:16] - * bits to clear the selected interrupt pending bits. - * @param __INTERRUPT__: specifies the interrupt pending bit to clear. - * This parameter can be any combination of the following values: - * @arg RCC_IT_LSIRDY: LSI ready interrupt. - * @arg RCC_IT_LSERDY: LSE ready interrupt. - * @arg RCC_IT_HSIRDY: HSI ready interrupt. - * @arg RCC_IT_HSERDY: HSE ready interrupt. - * @arg RCC_IT_PLLRDY: Main PLL ready interrupt. - * @arg RCC_IT_PLLI2SRDY: PLLI2S ready interrupt. - * @arg RCC_IT_CSS: Clock Security System interrupt - */ -#define __HAL_RCC_CLEAR_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE2_ADDRESS = (__INTERRUPT__)) - -/** @brief Check the RCC's interrupt has occurred or not. - * @param __INTERRUPT__: specifies the RCC interrupt source to check. - * This parameter can be one of the following values: - * @arg RCC_IT_LSIRDY: LSI ready interrupt. - * @arg RCC_IT_LSERDY: LSE ready interrupt. - * @arg RCC_IT_HSIRDY: HSI ready interrupt. - * @arg RCC_IT_HSERDY: HSE ready interrupt. - * @arg RCC_IT_PLLRDY: Main PLL ready interrupt. - * @arg RCC_IT_PLLI2SRDY: PLLI2S ready interrupt. - * @arg RCC_IT_CSS: Clock Security System interrupt - * @retval The new state of __INTERRUPT__ (TRUE or FALSE). - */ -#define __HAL_RCC_GET_IT(__INTERRUPT__) ((RCC->CIR & (__INTERRUPT__)) == (__INTERRUPT__)) - -/** @brief Set RMVF bit to clear the reset flags: RCC_FLAG_PINRST, RCC_FLAG_PORRST, - * RCC_FLAG_SFTRST, RCC_FLAG_IWDGRST, RCC_FLAG_WWDGRST and RCC_FLAG_LPWRRST. - */ -#define __HAL_RCC_CLEAR_RESET_FLAGS() (RCC->CSR |= RCC_CSR_RMVF) - -/** @brief Check RCC flag is set or not. - * @param __FLAG__: specifies the flag to check. - * This parameter can be one of the following values: - * @arg RCC_FLAG_HSIRDY: HSI oscillator clock ready. - * @arg RCC_FLAG_HSERDY: HSE oscillator clock ready. - * @arg RCC_FLAG_PLLRDY: Main PLL clock ready. - * @arg RCC_FLAG_PLLI2SRDY: PLLI2S clock ready. - * @arg RCC_FLAG_LSERDY: LSE oscillator clock ready. - * @arg RCC_FLAG_LSIRDY: LSI oscillator clock ready. - * @arg RCC_FLAG_BORRST: POR/PDR or BOR reset. - * @arg RCC_FLAG_PINRST: Pin reset. - * @arg RCC_FLAG_PORRST: POR/PDR reset. - * @arg RCC_FLAG_SFTRST: Software reset. - * @arg RCC_FLAG_IWDGRST: Independent Watchdog reset. - * @arg RCC_FLAG_WWDGRST: Window Watchdog reset. - * @arg RCC_FLAG_LPWRRST: Low Power reset. - * @retval The new state of __FLAG__ (TRUE or FALSE). - */ -#define RCC_FLAG_MASK ((uint8_t)0x1FU) -#define __HAL_RCC_GET_FLAG(__FLAG__) (((((((__FLAG__) >> 5U) == 1U)? RCC->CR :((((__FLAG__) >> 5U) == 2U) ? RCC->BDCR :((((__FLAG__) >> 5U) == 3U)? RCC->CSR :RCC->CIR))) & ((uint32_t)1U << ((__FLAG__) & RCC_FLAG_MASK)))!= 0U)? 1U : 0U) - -/** - * @} - */ - -/** - * @} - */ - -/* Exported functions --------------------------------------------------------*/ -/** @addtogroup RCC_Exported_Functions - * @{ - */ - -/** @addtogroup RCC_Exported_Functions_Group1 - * @{ - */ -/* Initialization and de-initialization functions ******************************/ -void HAL_RCC_DeInit(void); -HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef* RCC_OscInitStruct); -HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef* RCC_ClkInitStruct, uint32_t FLatency); -/** - * @} - */ - -/** @addtogroup RCC_Exported_Functions_Group2 - * @{ - */ -/* Peripheral Control functions ************************************************/ -void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv); -void HAL_RCC_EnableCSS(void); -void HAL_RCC_DisableCSS(void); -uint32_t HAL_RCC_GetSysClockFreq(void); -uint32_t HAL_RCC_GetHCLKFreq(void); -uint32_t HAL_RCC_GetPCLK1Freq(void); -uint32_t HAL_RCC_GetPCLK2Freq(void); -void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef* RCC_OscInitStruct); -void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef* RCC_ClkInitStruct, uint32_t* pFLatency); - -/* CSS NMI IRQ handler */ -void HAL_RCC_NMI_IRQHandler(void); - -/* User Callbacks in non blocking mode (IT mode) */ -void HAL_RCC_CSSCallback(void); - -/** - * @} - */ - -/** - * @} - */ - -/* Private types -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/* Private constants ---------------------------------------------------------*/ -/** @defgroup RCC_Private_Constants RCC Private Constants - * @{ - */ - -/** @defgroup RCC_BitAddress_AliasRegion RCC BitAddress AliasRegion - * @brief RCC registers bit address in the alias region - * @{ - */ -#define RCC_OFFSET (RCC_BASE - PERIPH_BASE) -/* --- CR Register ---*/ -/* Alias word address of HSION bit */ -#define RCC_CR_OFFSET (RCC_OFFSET + 0x00U) -#define RCC_HSION_BIT_NUMBER 0x00U -#define RCC_CR_HSION_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32U) + (RCC_HSION_BIT_NUMBER * 4U)) -/* Alias word address of CSSON bit */ -#define RCC_CSSON_BIT_NUMBER 0x13U -#define RCC_CR_CSSON_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32U) + (RCC_CSSON_BIT_NUMBER * 4U)) -/* Alias word address of PLLON bit */ -#define RCC_PLLON_BIT_NUMBER 0x18U -#define RCC_CR_PLLON_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32U) + (RCC_PLLON_BIT_NUMBER * 4U)) - -/* --- BDCR Register ---*/ -/* Alias word address of RTCEN bit */ -#define RCC_BDCR_OFFSET (RCC_OFFSET + 0x70U) -#define RCC_RTCEN_BIT_NUMBER 0x0FU -#define RCC_BDCR_RTCEN_BB (PERIPH_BB_BASE + (RCC_BDCR_OFFSET * 32U) + (RCC_RTCEN_BIT_NUMBER * 4U)) -/* Alias word address of BDRST bit */ -#define RCC_BDRST_BIT_NUMBER 0x10U -#define RCC_BDCR_BDRST_BB (PERIPH_BB_BASE + (RCC_BDCR_OFFSET * 32U) + (RCC_BDRST_BIT_NUMBER * 4U)) - -/* --- CSR Register ---*/ -/* Alias word address of LSION bit */ -#define RCC_CSR_OFFSET (RCC_OFFSET + 0x74U) -#define RCC_LSION_BIT_NUMBER 0x00U -#define RCC_CSR_LSION_BB (PERIPH_BB_BASE + (RCC_CSR_OFFSET * 32U) + (RCC_LSION_BIT_NUMBER * 4U)) - -/* CR register byte 3 (Bits[23:16]) base address */ -#define RCC_CR_BYTE2_ADDRESS ((uint32_t)0x40023802U) - -/* CIR register byte 2 (Bits[15:8]) base address */ -#define RCC_CIR_BYTE1_ADDRESS ((uint32_t)(RCC_BASE + 0x0CU + 0x01U)) - -/* CIR register byte 3 (Bits[23:16]) base address */ -#define RCC_CIR_BYTE2_ADDRESS ((uint32_t)(RCC_BASE + 0x0CU + 0x02U)) - -/* BDCR register base address */ -#define RCC_BDCR_BYTE0_ADDRESS (PERIPH_BASE + RCC_BDCR_OFFSET) - -#define RCC_DBP_TIMEOUT_VALUE ((uint32_t)2U) -#define RCC_LSE_TIMEOUT_VALUE LSE_STARTUP_TIMEOUT - -#define HSE_TIMEOUT_VALUE HSE_STARTUP_TIMEOUT -#define HSI_TIMEOUT_VALUE ((uint32_t)2U) /* 2 ms */ -#define LSI_TIMEOUT_VALUE ((uint32_t)2U) /* 2 ms */ - -/** - * @} - */ - -/** - * @} - */ - -/* Private macros ------------------------------------------------------------*/ -/** @defgroup RCC_Private_Macros RCC Private Macros - * @{ - */ - -/** @defgroup RCC_IS_RCC_Definitions RCC Private macros to check input parameters - * @{ - */ -#define IS_RCC_OSCILLATORTYPE(OSCILLATOR) ((OSCILLATOR) <= 15U) - -#define IS_RCC_HSE(HSE) (((HSE) == RCC_HSE_OFF) || ((HSE) == RCC_HSE_ON) || \ - ((HSE) == RCC_HSE_BYPASS)) - -#define IS_RCC_LSE(LSE) (((LSE) == RCC_LSE_OFF) || ((LSE) == RCC_LSE_ON) || \ - ((LSE) == RCC_LSE_BYPASS)) - -#define IS_RCC_HSI(HSI) (((HSI) == RCC_HSI_OFF) || ((HSI) == RCC_HSI_ON)) - -#define IS_RCC_LSI(LSI) (((LSI) == RCC_LSI_OFF) || ((LSI) == RCC_LSI_ON)) - -#define IS_RCC_PLL(PLL) (((PLL) == RCC_PLL_NONE) ||((PLL) == RCC_PLL_OFF) || ((PLL) == RCC_PLL_ON)) - -#define IS_RCC_PLLSOURCE(SOURCE) (((SOURCE) == RCC_PLLSOURCE_HSI) || \ - ((SOURCE) == RCC_PLLSOURCE_HSE)) - -#define IS_RCC_SYSCLKSOURCE(SOURCE) (((SOURCE) == RCC_SYSCLKSOURCE_HSI) || \ - ((SOURCE) == RCC_SYSCLKSOURCE_HSE) || \ - ((SOURCE) == RCC_SYSCLKSOURCE_PLLCLK) || \ - ((SOURCE) == RCC_SYSCLKSOURCE_PLLRCLK)) - -#define IS_RCC_RTCCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_RTCCLKSOURCE_LSE) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_LSI) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV2) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV3) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV4) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV5) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV6) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV7) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV8) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV9) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV10) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV11) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV12) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV13) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV14) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV15) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV16) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV17) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV18) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV19) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV20) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV21) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV22) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV23) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV24) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV25) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV26) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV27) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV28) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV29) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV30) || \ - ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV31)) - -#define IS_RCC_PLLM_VALUE(VALUE) ((VALUE) <= 63U) - -#define IS_RCC_PLLP_VALUE(VALUE) (((VALUE) == 2U) || ((VALUE) == 4U) || ((VALUE) == 6U) || ((VALUE) == 8U)) - -#define IS_RCC_PLLQ_VALUE(VALUE) ((4U <= (VALUE)) && ((VALUE) <= 15U)) - -#define IS_RCC_HCLK(HCLK) (((HCLK) == RCC_SYSCLK_DIV1) || ((HCLK) == RCC_SYSCLK_DIV2) || \ - ((HCLK) == RCC_SYSCLK_DIV4) || ((HCLK) == RCC_SYSCLK_DIV8) || \ - ((HCLK) == RCC_SYSCLK_DIV16) || ((HCLK) == RCC_SYSCLK_DIV64) || \ - ((HCLK) == RCC_SYSCLK_DIV128) || ((HCLK) == RCC_SYSCLK_DIV256) || \ - ((HCLK) == RCC_SYSCLK_DIV512)) - -#define IS_RCC_CLOCKTYPE(CLK) ((1U <= (CLK)) && ((CLK) <= 15U)) - -#define IS_RCC_PCLK(PCLK) (((PCLK) == RCC_HCLK_DIV1) || ((PCLK) == RCC_HCLK_DIV2) || \ - ((PCLK) == RCC_HCLK_DIV4) || ((PCLK) == RCC_HCLK_DIV8) || \ - ((PCLK) == RCC_HCLK_DIV16)) - -#define IS_RCC_MCO(MCOx) (((MCOx) == RCC_MCO1) || ((MCOx) == RCC_MCO2)) - -#define IS_RCC_MCO1SOURCE(SOURCE) (((SOURCE) == RCC_MCO1SOURCE_HSI) || ((SOURCE) == RCC_MCO1SOURCE_LSE) || \ - ((SOURCE) == RCC_MCO1SOURCE_HSE) || ((SOURCE) == RCC_MCO1SOURCE_PLLCLK)) - -#define IS_RCC_MCODIV(DIV) (((DIV) == RCC_MCODIV_1) || ((DIV) == RCC_MCODIV_2) || \ - ((DIV) == RCC_MCODIV_3) || ((DIV) == RCC_MCODIV_4) || \ - ((DIV) == RCC_MCODIV_5)) -#define IS_RCC_CALIBRATION_VALUE(VALUE) ((VALUE) <= 0x1FU) - -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F4xx_HAL_RCC_H */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc_ex.h b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc_ex.h deleted file mode 100644 index 4deaf2b6..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc_ex.h +++ /dev/null @@ -1,6619 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_rcc_ex.h - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Header file of RCC HAL Extension module. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_RCC_EX_H -#define __STM32F4xx_HAL_RCC_EX_H - -#ifdef __cplusplus -extern "C" { -#endif - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_def.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @addtogroup RCCEx - * @{ - */ - -/* Exported types ------------------------------------------------------------*/ -/** @defgroup RCCEx_Exported_Types RCCEx Exported Types - * @{ - */ - -/** - * @brief RCC PLL configuration structure definition - */ -typedef struct -{ - uint32_t PLLState; /*!< The new state of the PLL. - This parameter can be a value of @ref RCC_PLL_Config */ - - uint32_t PLLSource; /*!< RCC_PLLSource: PLL entry clock source. - This parameter must be a value of @ref RCC_PLL_Clock_Source */ - - uint32_t PLLM; /*!< PLLM: Division factor for PLL VCO input clock. - This parameter must be a number between Min_Data = 0 and Max_Data = 63 */ - - uint32_t PLLN; /*!< PLLN: Multiplication factor for PLL VCO output clock. - This parameter must be a number between Min_Data = 50 and Max_Data = 432 - except for STM32F411xE devices where the Min_Data = 192 */ - - uint32_t PLLP; /*!< PLLP: Division factor for main system clock (SYSCLK). - This parameter must be a value of @ref RCC_PLLP_Clock_Divider */ - - uint32_t PLLQ; /*!< PLLQ: Division factor for OTG FS, SDIO and RNG clocks. - This parameter must be a number between Min_Data = 4 and Max_Data = 15 */ -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F446xx) || defined(STM32F469xx) ||\ - defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) - uint32_t PLLR; /*!< PLLR: PLL division factor for I2S, SAI, SYSTEM, SPDIFRX clocks. - This parameter is only available in STM32F410xx/STM32F446xx/STM32F469xx/STM32F479xx - and STM32F412Zx/STM32F412Vx/STM32F412Rx/STM32F412Cx devices. - This parameter must be a number between Min_Data = 2 and Max_Data = 7 */ -#endif /* STM32F410xx || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ -} RCC_PLLInitTypeDef; - -#if defined(STM32F446xx) -/** - * @brief PLLI2S Clock structure definition - */ -typedef struct -{ - uint32_t PLLI2SM; /*!< Specifies division factor for PLL VCO input clock. - This parameter must be a number between Min_Data = 2 and Max_Data = 63 */ - - uint32_t PLLI2SN; /*!< Specifies the multiplication factor for PLLI2S VCO output clock. - This parameter must be a number between Min_Data = 50 and Max_Data = 432 */ - - uint32_t PLLI2SP; /*!< Specifies division factor for SPDIFRX Clock. - This parameter must be a value of @ref RCCEx_PLLI2SP_Clock_Divider */ - - uint32_t PLLI2SQ; /*!< Specifies the division factor for SAI clock. - This parameter must be a number between Min_Data = 2 and Max_Data = 15. - This parameter will be used only when PLLI2S is selected as Clock Source SAI */ - - uint32_t PLLI2SR; /*!< Specifies the division factor for I2S clock. - This parameter must be a number between Min_Data = 2 and Max_Data = 7. - This parameter will be used only when PLLI2S is selected as Clock Source I2S */ -} RCC_PLLI2SInitTypeDef; - -/** - * @brief PLLSAI Clock structure definition - */ -typedef struct -{ - uint32_t PLLSAIM; /*!< Spcifies division factor for PLL VCO input clock. - This parameter must be a number between Min_Data = 2 and Max_Data = 63 */ - - uint32_t PLLSAIN; /*!< Specifies the multiplication factor for PLLI2S VCO output clock. - This parameter must be a number between Min_Data = 50 and Max_Data = 432 */ - - uint32_t PLLSAIP; /*!< Specifies division factor for OTG FS, SDIO and RNG clocks. - This parameter must be a value of @ref RCCEx_PLLSAIP_Clock_Divider */ - - uint32_t PLLSAIQ; /*!< Specifies the division factor for SAI clock. - This parameter must be a number between Min_Data = 2 and Max_Data = 15. - This parameter will be used only when PLLSAI is selected as Clock Source SAI */ -} RCC_PLLSAIInitTypeDef; - -/** - * @brief RCC extended clocks structure definition - */ -typedef struct -{ - uint32_t PeriphClockSelection; /*!< The Extended Clock to be configured. - This parameter can be a value of @ref RCCEx_Periph_Clock_Selection */ - - RCC_PLLI2SInitTypeDef PLLI2S; /*!< PLL I2S structure parameters. - This parameter will be used only when PLLI2S is selected as Clock Source I2S or SAI */ - - RCC_PLLSAIInitTypeDef PLLSAI; /*!< PLL SAI structure parameters. - This parameter will be used only when PLLI2S is selected as Clock Source SAI or LTDC */ - - uint32_t PLLI2SDivQ; /*!< Specifies the PLLI2S division factor for SAI1 clock. - This parameter must be a number between Min_Data = 1 and Max_Data = 32 - This parameter will be used only when PLLI2S is selected as Clock Source SAI */ - - uint32_t PLLSAIDivQ; /*!< Specifies the PLLI2S division factor for SAI1 clock. - This parameter must be a number between Min_Data = 1 and Max_Data = 32 - This parameter will be used only when PLLSAI is selected as Clock Source SAI */ - - uint32_t Sai1ClockSelection; /*!< Specifies SAI1 Clock Source Selection. - This parameter can be a value of @ref RCCEx_SAI1_Clock_Source */ - - uint32_t Sai2ClockSelection; /*!< Specifies SAI2 Clock Source Selection. - This parameter can be a value of @ref RCCEx_SAI2_Clock_Source */ - - uint32_t I2sApb1ClockSelection; /*!< Specifies I2S APB1 Clock Source Selection. - This parameter can be a value of @ref RCCEx_I2SAPB1_Clock_Source */ - - uint32_t I2sApb2ClockSelection; /*!< Specifies I2S APB2 Clock Source Selection. - This parameter can be a value of @ref RCCEx_I2SAPB2_Clock_Source */ - - uint32_t RTCClockSelection; /*!< Specifies RTC Clock Source Selection. - This parameter can be a value of @ref RCC_RTC_Clock_Source */ - - uint32_t SdioClockSelection; /*!< Specifies SDIO Clock Source Selection. - This parameter can be a value of @ref RCCEx_SDIO_Clock_Source */ - - uint32_t CecClockSelection; /*!< Specifies CEC Clock Source Selection. - This parameter can be a value of @ref RCCEx_CEC_Clock_Source */ - - uint32_t Fmpi2c1ClockSelection; /*!< Specifies FMPI2C1 Clock Source Selection. - This parameter can be a value of @ref RCCEx_FMPI2C1_Clock_Source */ - - uint32_t SpdifClockSelection; /*!< Specifies SPDIFRX Clock Source Selection. - This parameter can be a value of @ref RCCEx_SPDIFRX_Clock_Source */ - - uint32_t Clk48ClockSelection; /*!< Specifies CLK48 Clock Selection this clock used OTG FS, SDIO and RNG clocks. - This parameter can be a value of @ref RCCEx_CLK48_Clock_Source */ - - uint8_t TIMPresSelection; /*!< Specifies TIM Clock Source Selection. - This parameter can be a value of @ref RCCEx_TIM_PRescaler_Selection */ -} RCC_PeriphCLKInitTypeDef; -#endif /* STM32F446xx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -/** - * @brief RCC extended clocks structure definition - */ -typedef struct -{ - uint32_t PeriphClockSelection; /*!< The Extended Clock to be configured. - This parameter can be a value of @ref RCCEx_Periph_Clock_Selection */ - - uint32_t I2SClockSelection; /*!< Specifies RTC Clock Source Selection. - This parameter can be a value of @ref RCCEx_I2S_APB_Clock_Source */ - - uint32_t RTCClockSelection; /*!< Specifies RTC Clock Source Selection. - This parameter can be a value of @ref RCC_RTC_Clock_Source */ - - uint32_t Lptim1ClockSelection; /*!< Specifies LPTIM1 Clock Source Selection. - This parameter can be a value of @ref RCCEx_LPTIM1_Clock_Source */ - - uint32_t Fmpi2c1ClockSelection; /*!< Specifies FMPI2C1 Clock Source Selection. - This parameter can be a value of @ref RCCEx_FMPI2C1_Clock_Source */ - - uint8_t TIMPresSelection; /*!< Specifies TIM Clock Source Selection. - This parameter can be a value of @ref RCCEx_TIM_PRescaler_Selection */ -} RCC_PeriphCLKInitTypeDef; -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -/** - * @brief PLLI2S Clock structure definition - */ -typedef struct -{ - uint32_t PLLI2SM; /*!< Specifies division factor for PLL VCO input clock. - This parameter must be a number between Min_Data = 2 and Max_Data = 63 */ - - uint32_t PLLI2SN; /*!< Specifies the multiplication factor for PLLI2S VCO output clock. - This parameter must be a number between Min_Data = 50 and Max_Data = 432 */ - - uint32_t PLLI2SQ; /*!< Specifies the division factor for SAI clock. - This parameter must be a number between Min_Data = 2 and Max_Data = 15. - This parameter will be used only when PLLI2S is selected as Clock Source SAI */ - - uint32_t PLLI2SR; /*!< Specifies the division factor for I2S clock. - This parameter must be a number between Min_Data = 2 and Max_Data = 7. - This parameter will be used only when PLLI2S is selected as Clock Source I2S */ -} RCC_PLLI2SInitTypeDef; - -/** - * @brief RCC extended clocks structure definition - */ -typedef struct -{ - uint32_t PeriphClockSelection; /*!< The Extended Clock to be configured. - This parameter can be a value of @ref RCCEx_Periph_Clock_Selection */ - - RCC_PLLI2SInitTypeDef PLLI2S; /*!< PLL I2S structure parameters. - This parameter will be used only when PLLI2S is selected as Clock Source I2S */ - - uint32_t I2sApb1ClockSelection; /*!< Specifies I2S APB1 Clock Source Selection. - This parameter can be a value of @ref RCCEx_I2SAPB1_Clock_Source */ - - uint32_t I2sApb2ClockSelection; /*!< Specifies I2S APB2 Clock Source Selection. - This parameter can be a value of @ref RCCEx_I2SAPB2_Clock_Source */ - - uint32_t RTCClockSelection; /*!< Specifies RTC Clock Source Selection. - This parameter can be a value of @ref RCC_RTC_Clock_Source */ - - uint32_t SdioClockSelection; /*!< Specifies SDIO Clock Source Selection. - This parameter can be a value of @ref RCCEx_SDIO_Clock_Source */ - - uint32_t Fmpi2c1ClockSelection; /*!< Specifies FMPI2C1 Clock Source Selection. - This parameter can be a value of @ref RCCEx_FMPI2C1_Clock_Source */ - - uint32_t Clk48ClockSelection; /*!< Specifies CLK48 Clock Selection this clock used OTG FS, SDIO and RNG clocks. - This parameter can be a value of @ref RCCEx_CLK48_Clock_Source */ - - uint32_t Dfsdm1ClockSelection; /*!< Specifies DFSDM1 Clock Selection. - This parameter can be a value of @ref RCCEx_DFSDM1_Kernel_Clock_Source */ - - uint32_t Dfsdm1AudioClockSelection;/*!< Specifies DFSDM1 Audio Clock Selection. - This parameter can be a value of @ref RCCEx_DFSDM1_Audio_Clock_Source */ - - uint32_t PLLI2SSelection; /*!< Specifies PLL I2S Clock Source Selection. - This parameter can be a value of @ref RCCEx_PLL_I2S_Clock_Source */ - - uint8_t TIMPresSelection; /*!< Specifies TIM Clock Source Selection. - This parameter can be a value of @ref RCCEx_TIM_PRescaler_Selection */ -} RCC_PeriphCLKInitTypeDef; -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) - -/** - * @brief PLLI2S Clock structure definition - */ -typedef struct -{ - uint32_t PLLI2SN; /*!< Specifies the multiplication factor for PLLI2S VCO output clock. - This parameter must be a number between Min_Data = 50 and Max_Data = 432. - This parameter will be used only when PLLI2S is selected as Clock Source I2S or SAI */ - - uint32_t PLLI2SR; /*!< Specifies the division factor for I2S clock. - This parameter must be a number between Min_Data = 2 and Max_Data = 7. - This parameter will be used only when PLLI2S is selected as Clock Source I2S or SAI */ - - uint32_t PLLI2SQ; /*!< Specifies the division factor for SAI1 clock. - This parameter must be a number between Min_Data = 2 and Max_Data = 15. - This parameter will be used only when PLLI2S is selected as Clock Source SAI */ -} RCC_PLLI2SInitTypeDef; - -/** - * @brief PLLSAI Clock structure definition - */ -typedef struct -{ - uint32_t PLLSAIN; /*!< Specifies the multiplication factor for PLLI2S VCO output clock. - This parameter must be a number between Min_Data = 50 and Max_Data = 432. - This parameter will be used only when PLLSAI is selected as Clock Source SAI or LTDC */ -#if defined(STM32F469xx) || defined(STM32F479xx) - uint32_t PLLSAIP; /*!< Specifies division factor for OTG FS and SDIO clocks. - This parameter is only available in STM32F469xx/STM32F479xx devices. - This parameter must be a value of @ref RCCEx_PLLSAIP_Clock_Divider */ -#endif /* STM32F469xx || STM32F479xx */ - - uint32_t PLLSAIQ; /*!< Specifies the division factor for SAI1 clock. - This parameter must be a number between Min_Data = 2 and Max_Data = 15. - This parameter will be used only when PLLSAI is selected as Clock Source SAI or LTDC */ - - uint32_t PLLSAIR; /*!< specifies the division factor for LTDC clock - This parameter must be a number between Min_Data = 2 and Max_Data = 7. - This parameter will be used only when PLLSAI is selected as Clock Source LTDC */ - -} RCC_PLLSAIInitTypeDef; - -/** - * @brief RCC extended clocks structure definition - */ -typedef struct -{ - uint32_t PeriphClockSelection; /*!< The Extended Clock to be configured. - This parameter can be a value of @ref RCCEx_Periph_Clock_Selection */ - - RCC_PLLI2SInitTypeDef PLLI2S; /*!< PLL I2S structure parameters. - This parameter will be used only when PLLI2S is selected as Clock Source I2S or SAI */ - - RCC_PLLSAIInitTypeDef PLLSAI; /*!< PLL SAI structure parameters. - This parameter will be used only when PLLI2S is selected as Clock Source SAI or LTDC */ - - uint32_t PLLI2SDivQ; /*!< Specifies the PLLI2S division factor for SAI1 clock. - This parameter must be a number between Min_Data = 1 and Max_Data = 32 - This parameter will be used only when PLLI2S is selected as Clock Source SAI */ - - uint32_t PLLSAIDivQ; /*!< Specifies the PLLI2S division factor for SAI1 clock. - This parameter must be a number between Min_Data = 1 and Max_Data = 32 - This parameter will be used only when PLLSAI is selected as Clock Source SAI */ - - uint32_t PLLSAIDivR; /*!< Specifies the PLLSAI division factor for LTDC clock. - This parameter must be one value of @ref RCCEx_PLLSAI_DIVR */ - - uint32_t RTCClockSelection; /*!< Specifies RTC Clock Prescalers Selection. - This parameter can be a value of @ref RCC_RTC_Clock_Source */ - - uint8_t TIMPresSelection; /*!< Specifies TIM Clock Prescalers Selection. - This parameter can be a value of @ref RCCEx_TIM_PRescaler_Selection */ -#if defined(STM32F469xx) || defined(STM32F479xx) - uint32_t Clk48ClockSelection; /*!< Specifies CLK48 Clock Selection this clock used OTG FS, SDIO and RNG clocks. - This parameter can be a value of @ref RCCEx_CLK48_Clock_Source */ - - uint32_t SdioClockSelection; /*!< Specifies SDIO Clock Source Selection. - This parameter can be a value of @ref RCCEx_SDIO_Clock_Source */ -#endif /* STM32F469xx || STM32F479xx */ -} RCC_PeriphCLKInitTypeDef; - -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) ||\ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) -/** - * @brief PLLI2S Clock structure definition - */ -typedef struct -{ -#if defined(STM32F411xE) - uint32_t PLLI2SM; /*!< PLLM: Division factor for PLLI2S VCO input clock. - This parameter must be a number between Min_Data = 2 and Max_Data = 62 */ -#endif /* STM32F411xE */ - - uint32_t PLLI2SN; /*!< Specifies the multiplication factor for PLLI2S VCO output clock. - This parameter must be a number between Min_Data = 50 and Max_Data = 432 - Except for STM32F411xE devices where the Min_Data = 192. - This parameter will be used only when PLLI2S is selected as Clock Source I2S or SAI */ - - uint32_t PLLI2SR; /*!< Specifies the division factor for I2S clock. - This parameter must be a number between Min_Data = 2 and Max_Data = 7. - This parameter will be used only when PLLI2S is selected as Clock Source I2S or SAI */ - -} RCC_PLLI2SInitTypeDef; - -/** - * @brief RCC extended clocks structure definition - */ -typedef struct -{ - uint32_t PeriphClockSelection; /*!< The Extended Clock to be configured. - This parameter can be a value of @ref RCCEx_Periph_Clock_Selection */ - - RCC_PLLI2SInitTypeDef PLLI2S; /*!< PLL I2S structure parameters. - This parameter will be used only when PLLI2S is selected as Clock Source I2S or SAI */ - - uint32_t RTCClockSelection; /*!< Specifies RTC Clock Prescalers Selection. - This parameter can be a value of @ref RCC_RTC_Clock_Source */ -#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) - uint8_t TIMPresSelection; /*!< Specifies TIM Clock Source Selection. - This parameter can be a value of @ref RCCEx_TIM_PRescaler_Selection */ -#endif /* STM32F401xC || STM32F401xE || STM32F411xE */ -} RCC_PeriphCLKInitTypeDef; -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F401xC || STM32F401xE || STM32F411xE */ -/** - * @} - */ - -/* Exported constants --------------------------------------------------------*/ -/** @defgroup RCCEx_Exported_Constants RCCEx Exported Constants - * @{ - */ - -/** @defgroup RCCEx_Periph_Clock_Selection RCC Periph Clock Selection - * @{ - */ -/* Peripheral Clock source for STM32F412Zx/STM32F412Vx/STM32F412Rx/STM32F412Cx */ -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -#define RCC_PERIPHCLK_I2S_APB1 ((uint32_t)0x00000001U) -#define RCC_PERIPHCLK_I2S_APB2 ((uint32_t)0x00000002U) -#define RCC_PERIPHCLK_TIM ((uint32_t)0x00000004U) -#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000008U) -#define RCC_PERIPHCLK_FMPI2C1 ((uint32_t)0x00000010U) -#define RCC_PERIPHCLK_CLK48 ((uint32_t)0x00000020U) -#define RCC_PERIPHCLK_SDIO ((uint32_t)0x00000040U) -#define RCC_PERIPHCLK_PLLI2S ((uint32_t)0x00000080U) -#define RCC_PERIPHCLK_DFSDM1 ((uint32_t)0x00000100U) -#define RCC_PERIPHCLK_DFSDM1_AUDIO ((uint32_t)0x00000200U) -#endif /* STM32F412Zx || STM32F412Vx) || STM32F412Rx || STM32F412Cx */ -/*----------------------------------------------------------------------------*/ - -/*------------------- Peripheral Clock source for STM32F410xx ----------------*/ -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -#define RCC_PERIPHCLK_I2S ((uint32_t)0x00000001U) -#define RCC_PERIPHCLK_TIM ((uint32_t)0x00000002U) -#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000004U) -#define RCC_PERIPHCLK_FMPI2C1 ((uint32_t)0x00000008U) -#define RCC_PERIPHCLK_LPTIM1 ((uint32_t)0x00000010U) -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ -/*----------------------------------------------------------------------------*/ - -/*------------------- Peripheral Clock source for STM32F446xx ----------------*/ -#if defined(STM32F446xx) -#define RCC_PERIPHCLK_I2S_APB1 ((uint32_t)0x00000001U) -#define RCC_PERIPHCLK_I2S_APB2 ((uint32_t)0x00000002U) -#define RCC_PERIPHCLK_SAI1 ((uint32_t)0x00000004U) -#define RCC_PERIPHCLK_SAI2 ((uint32_t)0x00000008U) -#define RCC_PERIPHCLK_TIM ((uint32_t)0x00000010U) -#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000020U) -#define RCC_PERIPHCLK_CEC ((uint32_t)0x00000040U) -#define RCC_PERIPHCLK_FMPI2C1 ((uint32_t)0x00000080U) -#define RCC_PERIPHCLK_CLK48 ((uint32_t)0x00000100U) -#define RCC_PERIPHCLK_SDIO ((uint32_t)0x00000200U) -#define RCC_PERIPHCLK_SPDIFRX ((uint32_t)0x00000400U) -#define RCC_PERIPHCLK_PLLI2S ((uint32_t)0x00000800U) -#endif /* STM32F446xx */ -/*-----------------------------------------------------------------------------*/ - -/*----------- Peripheral Clock source for STM32F469xx/STM32F479xx -------------*/ -#if defined(STM32F469xx) || defined(STM32F479xx) -#define RCC_PERIPHCLK_I2S ((uint32_t)0x00000001U) -#define RCC_PERIPHCLK_SAI_PLLI2S ((uint32_t)0x00000002U) -#define RCC_PERIPHCLK_SAI_PLLSAI ((uint32_t)0x00000004U) -#define RCC_PERIPHCLK_LTDC ((uint32_t)0x00000008U) -#define RCC_PERIPHCLK_TIM ((uint32_t)0x00000010U) -#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000020U) -#define RCC_PERIPHCLK_PLLI2S ((uint32_t)0x00000040U) -#define RCC_PERIPHCLK_CLK48 ((uint32_t)0x00000080U) -#define RCC_PERIPHCLK_SDIO ((uint32_t)0x00000100U) -#endif /* STM32F469xx || STM32F479xx */ -/*----------------------------------------------------------------------------*/ - -/*-------- Peripheral Clock source for STM32F42xxx/STM32F43xxx ---------------*/ -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) -#define RCC_PERIPHCLK_I2S ((uint32_t)0x00000001U) -#define RCC_PERIPHCLK_SAI_PLLI2S ((uint32_t)0x00000002U) -#define RCC_PERIPHCLK_SAI_PLLSAI ((uint32_t)0x00000004U) -#define RCC_PERIPHCLK_LTDC ((uint32_t)0x00000008U) -#define RCC_PERIPHCLK_TIM ((uint32_t)0x00000010U) -#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000020U) -#define RCC_PERIPHCLK_PLLI2S ((uint32_t)0x00000040U) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */ -/*----------------------------------------------------------------------------*/ - -/*-------- Peripheral Clock source for STM32F40xxx/STM32F41xxx ---------------*/ -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx) ||\ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) -#define RCC_PERIPHCLK_I2S ((uint32_t)0x00000001U) -#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000002U) -#define RCC_PERIPHCLK_PLLI2S ((uint32_t)0x00000004U) -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F401xC || STM32F401xE || STM32F411xE */ -#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) -#define RCC_PERIPHCLK_TIM ((uint32_t)0x00000008U) -#endif /* STM32F401xC || STM32F401xE || STM32F411xE */ -/*----------------------------------------------------------------------------*/ -/** - * @} - */ -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \ - defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \ - defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ - defined(STM32F412Rx) || defined(STM32F412Cx) -/** @defgroup RCCEx_I2S_Clock_Source I2S Clock Source - * @{ - */ -#define RCC_I2SCLKSOURCE_PLLI2S ((uint32_t)0x00000000U) -#define RCC_I2SCLKSOURCE_EXT ((uint32_t)0x00000001U) -/** - * @} - */ -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || - STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || - STM32F412Rx || STM32F412Cx */ - -/** @defgroup RCCEx_PLLSAI_DIVR RCC PLLSAI DIVR - * @{ - */ -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx) ||\ - defined(STM32F469xx) || defined(STM32F479xx) -#define RCC_PLLSAIDIVR_2 ((uint32_t)0x00000000U) -#define RCC_PLLSAIDIVR_4 ((uint32_t)0x00010000U) -#define RCC_PLLSAIDIVR_8 ((uint32_t)0x00020000U) -#define RCC_PLLSAIDIVR_16 ((uint32_t)0x00030000U) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */ -/** - * @} - */ - -/** @defgroup RCCEx_PLLI2SP_Clock_Divider RCC PLLI2SP Clock Divider - * @{ - */ -#if defined(STM32F446xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ - defined(STM32F412Rx) || defined(STM32F412Cx) -#define RCC_PLLI2SP_DIV2 ((uint32_t)0x00000002U) -#define RCC_PLLI2SP_DIV4 ((uint32_t)0x00000004U) -#define RCC_PLLI2SP_DIV6 ((uint32_t)0x00000006U) -#define RCC_PLLI2SP_DIV8 ((uint32_t)0x00000008U) -#endif /* STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ -/** - * @} - */ - -/** @defgroup RCCEx_PLLSAIP_Clock_Divider RCC PLLSAIP Clock Divider - * @{ - */ -#if defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) -#define RCC_PLLSAIP_DIV2 ((uint32_t)0x00000002U) -#define RCC_PLLSAIP_DIV4 ((uint32_t)0x00000004U) -#define RCC_PLLSAIP_DIV6 ((uint32_t)0x00000006U) -#define RCC_PLLSAIP_DIV8 ((uint32_t)0x00000008U) -#endif /* STM32F446xx || STM32F469xx || STM32F479xx */ -/** - * @} - */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) -/** @defgroup RCCEx_SAI_BlockA_Clock_Source RCC SAI BlockA Clock Source - * @{ - */ -#define RCC_SAIACLKSOURCE_PLLSAI ((uint32_t)0x00000000U) -#define RCC_SAIACLKSOURCE_PLLI2S ((uint32_t)0x00100000U) -#define RCC_SAIACLKSOURCE_EXT ((uint32_t)0x00200000U) -/** - * @} - */ - -/** @defgroup RCCEx_SAI_BlockB_Clock_Source RCC SAI BlockB Clock Source - * @{ - */ -#define RCC_SAIBCLKSOURCE_PLLSAI ((uint32_t)0x00000000U) -#define RCC_SAIBCLKSOURCE_PLLI2S ((uint32_t)0x00400000U) -#define RCC_SAIBCLKSOURCE_EXT ((uint32_t)0x00800000U) -/** - * @} - */ -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F469xx) || defined(STM32F479xx) -/** @defgroup RCCEx_CLK48_Clock_Source RCC CLK48 Clock Source - * @{ - */ -#define RCC_CLK48CLKSOURCE_PLLQ ((uint32_t)0x00000000U) -#define RCC_CLK48CLKSOURCE_PLLSAIP ((uint32_t)RCC_DCKCFGR_CK48MSEL) -/** - * @} - */ - -/** @defgroup RCCEx_SDIO_Clock_Source RCC SDIO Clock Source - * @{ - */ -#define RCC_SDIOCLKSOURCE_CLK48 ((uint32_t)0x00000000U) -#define RCC_SDIOCLKSOURCE_SYSCLK ((uint32_t)RCC_DCKCFGR_SDIOSEL) -/** - * @} - */ - -/** @defgroup RCCEx_DSI_Clock_Source RCC DSI Clock Source - * @{ - */ -#define RCC_DSICLKSOURCE_DSIPHY ((uint32_t)0x00000000U) -#define RCC_DSICLKSOURCE_PLLR ((uint32_t)RCC_DCKCFGR_DSISEL) -/** - * @} - */ -#endif /* STM32F469xx || STM32F479xx */ - -#if defined(STM32F446xx) -/** @defgroup RCCEx_SAI1_Clock_Source RCC SAI1 Clock Source - * @{ - */ -#define RCC_SAI1CLKSOURCE_PLLSAI ((uint32_t)0x00000000U) -#define RCC_SAI1CLKSOURCE_PLLI2S ((uint32_t)RCC_DCKCFGR_SAI1SRC_0) -#define RCC_SAI1CLKSOURCE_PLLR ((uint32_t)RCC_DCKCFGR_SAI1SRC_1) -#define RCC_SAI1CLKSOURCE_EXT ((uint32_t)RCC_DCKCFGR_SAI1SRC) -/** - * @} - */ - -/** @defgroup RCCEx_SAI2_Clock_Source RCC SAI2 Clock Source - * @{ - */ -#define RCC_SAI2CLKSOURCE_PLLSAI ((uint32_t)0x00000000U) -#define RCC_SAI2CLKSOURCE_PLLI2S ((uint32_t)RCC_DCKCFGR_SAI2SRC_0) -#define RCC_SAI2CLKSOURCE_PLLR ((uint32_t)RCC_DCKCFGR_SAI2SRC_1) -#define RCC_SAI2CLKSOURCE_PLLSRC ((uint32_t)RCC_DCKCFGR_SAI2SRC) -/** - * @} - */ - -/** @defgroup RCCEx_I2SAPB1_Clock_Source RCC I2S APB1 Clock Source - * @{ - */ -#define RCC_I2SAPB1CLKSOURCE_PLLI2S ((uint32_t)0x00000000U) -#define RCC_I2SAPB1CLKSOURCE_EXT ((uint32_t)RCC_DCKCFGR_I2S1SRC_0) -#define RCC_I2SAPB1CLKSOURCE_PLLR ((uint32_t)RCC_DCKCFGR_I2S1SRC_1) -#define RCC_I2SAPB1CLKSOURCE_PLLSRC ((uint32_t)RCC_DCKCFGR_I2S1SRC) -/** - * @} - */ - -/** @defgroup RCCEx_I2SAPB2_Clock_Source RCC I2S APB2 Clock Source - * @{ - */ -#define RCC_I2SAPB2CLKSOURCE_PLLI2S ((uint32_t)0x00000000U) -#define RCC_I2SAPB2CLKSOURCE_EXT ((uint32_t)RCC_DCKCFGR_I2S2SRC_0) -#define RCC_I2SAPB2CLKSOURCE_PLLR ((uint32_t)RCC_DCKCFGR_I2S2SRC_1) -#define RCC_I2SAPB2CLKSOURCE_PLLSRC ((uint32_t)RCC_DCKCFGR_I2S2SRC) -/** - * @} - */ - -/** @defgroup RCCEx_FMPI2C1_Clock_Source RCC FMPI2C1 Clock Source - * @{ - */ -#define RCC_FMPI2C1CLKSOURCE_APB ((uint32_t)0x00000000U) -#define RCC_FMPI2C1CLKSOURCE_SYSCLK ((uint32_t)RCC_DCKCFGR2_FMPI2C1SEL_0) -#define RCC_FMPI2C1CLKSOURCE_HSI ((uint32_t)RCC_DCKCFGR2_FMPI2C1SEL_1) -/** - * @} - */ - -/** @defgroup RCCEx_CEC_Clock_Source RCC CEC Clock Source - * @{ - */ -#define RCC_CECCLKSOURCE_HSI ((uint32_t)0x00000000U) -#define RCC_CECCLKSOURCE_LSE ((uint32_t)RCC_DCKCFGR2_CECSEL) -/** - * @} - */ - -/** @defgroup RCCEx_CLK48_Clock_Source RCC CLK48 Clock Source - * @{ - */ -#define RCC_CLK48CLKSOURCE_PLLQ ((uint32_t)0x00000000U) -#define RCC_CLK48CLKSOURCE_PLLSAIP ((uint32_t)RCC_DCKCFGR2_CK48MSEL) -/** - * @} - */ - -/** @defgroup RCCEx_SDIO_Clock_Source RCC SDIO Clock Source - * @{ - */ -#define RCC_SDIOCLKSOURCE_CLK48 ((uint32_t)0x00000000U) -#define RCC_SDIOCLKSOURCE_SYSCLK ((uint32_t)RCC_DCKCFGR2_SDIOSEL) -/** - * @} - */ - -/** @defgroup RCCEx_SPDIFRX_Clock_Source RCC SPDIFRX Clock Source - * @{ - */ -#define RCC_SPDIFRXCLKSOURCE_PLLR ((uint32_t)0x00000000U) -#define RCC_SPDIFRXCLKSOURCE_PLLI2SP ((uint32_t)RCC_DCKCFGR2_SPDIFRXSEL) -/** - * @} - */ - -#endif /* STM32F446xx */ - -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -/** @defgroup RCCEx_PLL_I2S_Clock_Source PLL I2S Clock Source - * @{ - */ -#define RCC_PLLI2SCLKSOURCE_PLLSRC ((uint32_t)0x00000000U) -#define RCC_PLLI2SCLKSOURCE_EXT ((uint32_t)RCC_PLLI2SCFGR_PLLI2SSRC) -/** - * @} - */ - -/** @defgroup RCCEx_DFSDM1_Audio_Clock_Source RCC DFSDM1 Audio Clock Source - * @{ - */ -#define RCC_DFSDM1AUDIOCLKSOURCE_I2SAPB1 ((uint32_t)0x00000000U) -#define RCC_DFSDM1AUDIOCLKSOURCE_I2SAPB2 ((uint32_t)RCC_DCKCFGR_CKDFSDM1ASEL) -/** - * @} - */ - -/** @defgroup RCCEx_DFSDM1_Kernel_Clock_Source RCC DFSDM1 Kernel Clock Source - * @{ - */ -#define RCC_DFSDM1CLKSOURCE_APB2 ((uint32_t)0x00000000U) -#define RCC_DFSDM1CLKSOURCE_SYSCLK ((uint32_t)RCC_DCKCFGR_CKDFSDM1SEL) -/** - * @} - */ - -/** @defgroup RCCEx_I2SAPB1_Clock_Source RCC I2S APB1 Clock Source - * @{ - */ -#define RCC_I2SAPB1CLKSOURCE_PLLI2S ((uint32_t)0x00000000U) -#define RCC_I2SAPB1CLKSOURCE_EXT ((uint32_t)RCC_DCKCFGR_I2S1SRC_0) -#define RCC_I2SAPB1CLKSOURCE_PLLR ((uint32_t)RCC_DCKCFGR_I2S1SRC_1) -#define RCC_I2SAPB1CLKSOURCE_PLLSRC ((uint32_t)RCC_DCKCFGR_I2S1SRC) -/** - * @} - */ - -/** @defgroup RCCEx_I2SAPB2_Clock_Source RCC I2S APB2 Clock Source - * @{ - */ -#define RCC_I2SAPB2CLKSOURCE_PLLI2S ((uint32_t)0x00000000U) -#define RCC_I2SAPB2CLKSOURCE_EXT ((uint32_t)RCC_DCKCFGR_I2S2SRC_0) -#define RCC_I2SAPB2CLKSOURCE_PLLR ((uint32_t)RCC_DCKCFGR_I2S2SRC_1) -#define RCC_I2SAPB2CLKSOURCE_PLLSRC ((uint32_t)RCC_DCKCFGR_I2S2SRC) -/** - * @} - */ - -/** @defgroup RCCEx_FMPI2C1_Clock_Source RCC FMPI2C1 Clock Source - * @{ - */ -#define RCC_FMPI2C1CLKSOURCE_APB ((uint32_t)0x00000000U) -#define RCC_FMPI2C1CLKSOURCE_SYSCLK ((uint32_t)RCC_DCKCFGR2_FMPI2C1SEL_0) -#define RCC_FMPI2C1CLKSOURCE_HSI ((uint32_t)RCC_DCKCFGR2_FMPI2C1SEL_1) -/** - * @} - */ - -/** @defgroup RCCEx_CLK48_Clock_Source RCC CLK48 Clock Source - * @{ - */ -#define RCC_CLK48CLKSOURCE_PLLQ ((uint32_t)0x00000000U) -#define RCC_CLK48CLKSOURCE_PLLI2SQ ((uint32_t)RCC_DCKCFGR2_CK48MSEL) -/** - * @} - */ - -/** @defgroup RCCEx_SDIO_Clock_Source RCC SDIO Clock Source - * @{ - */ -#define RCC_SDIOCLKSOURCE_CLK48 ((uint32_t)0x00000000U) -#define RCC_SDIOCLKSOURCE_SYSCLK ((uint32_t)RCC_DCKCFGR2_SDIOSEL) -/** - * @} - */ -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) - -/** @defgroup RCCEx_I2S_APB_Clock_Source RCC I2S APB Clock Source - * @{ - */ -#define RCC_I2SAPBCLKSOURCE_PLLR ((uint32_t)0x00000000U) -#define RCC_I2SAPBCLKSOURCE_EXT ((uint32_t)RCC_DCKCFGR_I2SSRC_0) -#define RCC_I2SAPBCLKSOURCE_PLLSRC ((uint32_t)RCC_DCKCFGR_I2SSRC_1) -/** - * @} - */ - -/** @defgroup RCCEx_FMPI2C1_Clock_Source RCC FMPI2C1 Clock Source - * @{ - */ -#define RCC_FMPI2C1CLKSOURCE_APB ((uint32_t)0x00000000U) -#define RCC_FMPI2C1CLKSOURCE_SYSCLK ((uint32_t)RCC_DCKCFGR2_FMPI2C1SEL_0) -#define RCC_FMPI2C1CLKSOURCE_HSI ((uint32_t)RCC_DCKCFGR2_FMPI2C1SEL_1) -/** - * @} - */ - -/** @defgroup RCCEx_LPTIM1_Clock_Source RCC LPTIM1 Clock Source - * @{ - */ -#define RCC_LPTIM1CLKSOURCE_PCLK ((uint32_t)0x00000000U) -#define RCC_LPTIM1CLKSOURCE_HSI ((uint32_t)RCC_DCKCFGR2_LPTIM1SEL_0) -#define RCC_LPTIM1CLKSOURCE_LSI ((uint32_t)RCC_DCKCFGR2_LPTIM1SEL_1) -#define RCC_LPTIM1CLKSOURCE_LSE ((uint32_t)RCC_DCKCFGR2_LPTIM1SEL_0 | RCC_DCKCFGR2_LPTIM1SEL_1) -/** - * @} - */ -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) ||\ - defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F469xx) ||\ - defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) ||\ - defined(STM32F412Cx) -/** @defgroup RCCEx_TIM_PRescaler_Selection RCC TIM PRescaler Selection - * @{ - */ -#define RCC_TIMPRES_DESACTIVATED ((uint8_t)0x00U) -#define RCC_TIMPRES_ACTIVATED ((uint8_t)0x01U) -/** - * @} - */ -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F401xC || STM32F401xE ||\ - STM32F410xx || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx ||\ - STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F411xE) ||\ - defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) ||\ - defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -/** @defgroup RCCEx_LSE_Dual_Mode_Selection RCC LSE Dual Mode Selection - * @{ - */ -#define RCC_LSE_LOWPOWER_MODE ((uint8_t)0x00U) -#define RCC_LSE_HIGHDRIVE_MODE ((uint8_t)0x01U) -/** - * @} - */ -#endif /* STM32F410xx || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx ||\ - STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \ - defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \ - defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ - defined(STM32F412Rx) -/** @defgroup RCC_MCO2_Clock_Source MCO2 Clock Source - * @{ - */ -#define RCC_MCO2SOURCE_SYSCLK ((uint32_t)0x00000000U) -#define RCC_MCO2SOURCE_PLLI2SCLK RCC_CFGR_MCO2_0 -#define RCC_MCO2SOURCE_HSE RCC_CFGR_MCO2_1 -#define RCC_MCO2SOURCE_PLLCLK RCC_CFGR_MCO2 -/** - * @} - */ -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || - STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || - STM32F412Rx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -/** @defgroup RCC_MCO2_Clock_Source MCO2 Clock Source - * @{ - */ -#define RCC_MCO2SOURCE_SYSCLK ((uint32_t)0x00000000U) -#define RCC_MCO2SOURCE_I2SCLK RCC_CFGR_MCO2_0 -#define RCC_MCO2SOURCE_HSE RCC_CFGR_MCO2_1 -#define RCC_MCO2SOURCE_PLLCLK RCC_CFGR_MCO2 -/** - * @} - */ -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -/** - * @} - */ - -/* Exported macro ------------------------------------------------------------*/ -/** @defgroup RCCEx_Exported_Macros RCCEx Exported Macros - * @{ - */ -/*------------------- STM32F42xxx/STM32F43xxx/STM32F469xx/STM32F479xx --------*/ -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) -/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable - * @brief Enables or disables the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_BKPSRAM_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CCMDATARAMEN_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CRC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOI_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOIEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOIEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOF_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOFEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOFEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOG_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOGEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOGEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOJ_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOJEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOJEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOK_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOKEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOKEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_DMA2D_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2DEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2DEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_ETHMAC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_ETHMACTX_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACTXEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACTXEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_ETHMACRX_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACRXEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACRXEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_ETHMACPTP_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACPTPEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACPTPEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_USB_OTG_HS_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSULPIEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSULPIEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN)) -#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN)) -#define __HAL_RCC_GPIOF_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOFEN)) -#define __HAL_RCC_GPIOG_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOGEN)) -#define __HAL_RCC_GPIOI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOIEN)) -#define __HAL_RCC_GPIOJ_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOJEN)) -#define __HAL_RCC_GPIOK_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOKEN)) -#define __HAL_RCC_DMA2D_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_DMA2DEN)) -#define __HAL_RCC_ETHMAC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACEN)) -#define __HAL_RCC_ETHMACTX_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACTXEN)) -#define __HAL_RCC_ETHMACRX_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACRXEN)) -#define __HAL_RCC_ETHMACPTP_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACPTPEN)) -#define __HAL_RCC_USB_OTG_HS_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSEN)) -#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSULPIEN)) -#define __HAL_RCC_BKPSRAM_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_BKPSRAMEN)) -#define __HAL_RCC_CCMDATARAMEN_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CCMDATARAMEN)) -#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN)) - -/** - * @brief Enable ETHERNET clock. - */ -#define __HAL_RCC_ETH_CLK_ENABLE() do { \ - __HAL_RCC_ETHMAC_CLK_ENABLE(); \ - __HAL_RCC_ETHMACTX_CLK_ENABLE(); \ - __HAL_RCC_ETHMACRX_CLK_ENABLE(); \ - } while(0) -/** - * @brief Disable ETHERNET clock. - */ -#define __HAL_RCC_ETH_CLK_DISABLE() do { \ - __HAL_RCC_ETHMACTX_CLK_DISABLE(); \ - __HAL_RCC_ETHMACRX_CLK_DISABLE(); \ - __HAL_RCC_ETHMAC_CLK_DISABLE(); \ - } while(0) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_Peripheral_Clock_Enable_Disable_Status AHB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_GPIOD_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIODEN)) != RESET) -#define __HAL_RCC_GPIOE_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOEEN)) != RESET) -#define __HAL_RCC_GPIOF_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOFEN)) != RESET) -#define __HAL_RCC_GPIOG_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOGEN)) != RESET) -#define __HAL_RCC_GPIOI_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOIEN)) != RESET) -#define __HAL_RCC_GPIOJ_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOJEN)) != RESET) -#define __HAL_RCC_GPIOK_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOKEN)) != RESET) -#define __HAL_RCC_DMA2D_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_DMA2DEN)) != RESET) -#define __HAL_RCC_ETHMAC_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACEN)) != RESET) -#define __HAL_RCC_ETHMACTX_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACTXEN)) != RESET) -#define __HAL_RCC_ETHMACRX_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACRXEN)) != RESET) -#define __HAL_RCC_ETHMACPTP_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACPTPEN)) != RESET) -#define __HAL_RCC_USB_OTG_HS_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_OTGHSEN)) != RESET) -#define __HAL_RCC_USB_OTG_HS_ULPI_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_OTGHSULPIEN)) != RESET) -#define __HAL_RCC_BKPSRAM_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_BKPSRAMEN)) != RESET) -#define __HAL_RCC_CCMDATARAMEN_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CCMDATARAMEN)) != RESET) -#define __HAL_RCC_CRC_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CRCEN)) != RESET) -#define __HAL_RCC_ETH_IS_CLK_ENABLED() (__HAL_RCC_ETHMAC_IS_CLK_ENABLED() && \ - __HAL_RCC_ETHMACTX_IS_CLK_ENABLED() && \ - __HAL_RCC_ETHMACRX_IS_CLK_ENABLED()) - -#define __HAL_RCC_GPIOD_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIODEN)) == RESET) -#define __HAL_RCC_GPIOE_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOEEN)) == RESET) -#define __HAL_RCC_GPIOF_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOFEN)) == RESET) -#define __HAL_RCC_GPIOG_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOGEN)) == RESET) -#define __HAL_RCC_GPIOI_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOIEN)) == RESET) -#define __HAL_RCC_GPIOJ_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOJEN)) == RESET) -#define __HAL_RCC_GPIOK_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOKEN)) == RESET) -#define __HAL_RCC_DMA2D_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_DMA2DEN)) == RESET) -#define __HAL_RCC_ETHMAC_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACEN)) == RESET) -#define __HAL_RCC_ETHMACTX_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACTXEN)) == RESET) -#define __HAL_RCC_ETHMACRX_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACRXEN)) == RESET) -#define __HAL_RCC_ETHMACPTP_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACPTPEN)) == RESET) -#define __HAL_RCC_USB_OTG_HS_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_OTGHSEN)) == RESET) -#define __HAL_RCC_USB_OTG_HS_ULPI_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_OTGHSULPIEN)) == RESET) -#define __HAL_RCC_BKPSRAM_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_BKPSRAMEN)) == RESET) -#define __HAL_RCC_CCMDATARAMEN_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CCMDATARAMEN)) == RESET) -#define __HAL_RCC_CRC_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CRCEN)) == RESET) -#define __HAL_RCC_ETH_IS_CLK_DISABLED() (__HAL_RCC_ETHMAC_IS_CLK_DISABLED() && \ - __HAL_RCC_ETHMACTX_IS_CLK_DISABLED() && \ - __HAL_RCC_ETHMACRX_IS_CLK_DISABLED()) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable - * @brief Enable or disable the AHB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_DCMI_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_DCMIEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_DCMIEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_DCMI_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_DCMIEN)) - -#if defined(STM32F437xx)|| defined(STM32F439xx) || defined(STM32F479xx) -#define __HAL_RCC_CRYP_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_CRYPEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_CRYPEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_HASH_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_HASHEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_HASHEN);\ - UNUSED(tmpreg); \ - } while(0) - -#define __HAL_RCC_CRYP_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_CRYPEN)) -#define __HAL_RCC_HASH_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_HASHEN)) -#endif /* STM32F437xx || STM32F439xx || STM32F479xx */ - -#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\ - __HAL_RCC_SYSCFG_CLK_ENABLE();\ - }while(0) - -#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN)) - -#define __HAL_RCC_RNG_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_RNG_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_RNGEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Peripheral_Clock_Enable_Disable_Status AHB2 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_DCMI_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_DCMIEN)) != RESET) -#define __HAL_RCC_DCMI_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_DCMIEN)) == RESET) - -#if defined(STM32F437xx)|| defined(STM32F439xx) || defined(STM32F479xx) -#define __HAL_RCC_CRYP_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_CRYPEN)) != RESET) -#define __HAL_RCC_CRYP_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_CRYPEN)) == RESET) - -#define __HAL_RCC_HASH_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_HASHEN)) != RESET) -#define __HAL_RCC_HASH_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_HASHEN)) == RESET) -#endif /* STM32F437xx || STM32F439xx || STM32F479xx */ - -#define __HAL_RCC_USB_OTG_FS_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_OTGFSEN)) != RESET) -#define __HAL_RCC_USB_OTG_FS_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_OTGFSEN)) == RESET) - -#define __HAL_RCC_RNG_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_RNGEN)) != RESET) -#define __HAL_RCC_RNG_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_RNGEN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_Clock_Enable_Disable AHB3 Peripheral Clock Enable Disable - * @brief Enables or disables the AHB3 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_FMC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_FMC_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_FMCEN)) -#if defined(STM32F469xx) || defined(STM32F479xx) -#define __HAL_RCC_QSPI_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_QSPI_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_QSPIEN)) -#endif /* STM32F469xx || STM32F479xx */ -/** - * @} - */ - - -/** @defgroup RCCEx_AHB3_Peripheral_Clock_Enable_Disable_Status AHB3 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB3 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_FMC_IS_CLK_ENABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_FMCEN)) != RESET) -#define __HAL_RCC_FMC_IS_CLK_DISABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_FMCEN)) == RESET) -#if defined(STM32F469xx) || defined(STM32F479xx) -#define __HAL_RCC_QSPI_IS_CLK_ENABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_QSPIEN)) != RESET) -#define __HAL_RCC_QSPI_IS_CLK_DISABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_QSPIEN)) == RESET) -#endif /* STM32F469xx || STM32F479xx */ -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable - * @brief Enable or disable the Low Speed APB (APB1) peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM6_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM7_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM7EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM7EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM12_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM12EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM12EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM13_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM13EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM13EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM14_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM14_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_USART3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_USART3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_USART3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_UART4_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_UART4EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_UART4EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_UART5_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_UART5EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_UART5EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CAN1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CAN2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_DAC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_UART7_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_UART7EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_UART7EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_UART8_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_UART8EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_UART8EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM4_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_I2C3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN)) -#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN)) -#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN)) -#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN)) -#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN)) -#define __HAL_RCC_TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN)) -#define __HAL_RCC_TIM7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM7EN)) -#define __HAL_RCC_TIM12_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM12EN)) -#define __HAL_RCC_TIM13_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM13EN)) -#define __HAL_RCC_TIM14_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM14EN)) -#define __HAL_RCC_USART3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_USART3EN)) -#define __HAL_RCC_UART4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART4EN)) -#define __HAL_RCC_UART5_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART5EN)) -#define __HAL_RCC_CAN1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN1EN)) -#define __HAL_RCC_CAN2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN2EN)) -#define __HAL_RCC_DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN)) -#define __HAL_RCC_UART7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART7EN)) -#define __HAL_RCC_UART8_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART8EN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Peripheral_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) != RESET) -#define __HAL_RCC_TIM3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) != RESET) -#define __HAL_RCC_TIM4_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM4EN)) != RESET) -#define __HAL_RCC_SPI3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) != RESET) -#define __HAL_RCC_I2C3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C3EN)) != RESET) -#define __HAL_RCC_TIM6_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM6EN)) != RESET) -#define __HAL_RCC_TIM7_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM7EN)) != RESET) -#define __HAL_RCC_TIM12_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM12EN)) != RESET) -#define __HAL_RCC_TIM13_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM13EN)) != RESET) -#define __HAL_RCC_TIM14_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM14EN)) != RESET) -#define __HAL_RCC_USART3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART3EN)) != RESET) -#define __HAL_RCC_UART4_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART4EN)) != RESET) -#define __HAL_RCC_UART5_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART5EN)) != RESET) -#define __HAL_RCC_CAN1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN1EN)) != RESET) -#define __HAL_RCC_CAN2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN2EN)) != RESET) -#define __HAL_RCC_DAC_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_DACEN)) != RESET) -#define __HAL_RCC_UART7_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART7EN)) != RESET) -#define __HAL_RCC_UART8_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART8EN)) != RESET) - -#define __HAL_RCC_TIM2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) == RESET) -#define __HAL_RCC_TIM3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) == RESET) -#define __HAL_RCC_TIM4_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM4EN)) == RESET) -#define __HAL_RCC_SPI3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) == RESET) -#define __HAL_RCC_I2C3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C3EN)) == RESET) -#define __HAL_RCC_TIM6_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM6EN)) == RESET) -#define __HAL_RCC_TIM7_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM7EN)) == RESET) -#define __HAL_RCC_TIM12_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM12EN)) == RESET) -#define __HAL_RCC_TIM13_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM13EN)) == RESET) -#define __HAL_RCC_TIM14_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM14EN)) == RESET) -#define __HAL_RCC_USART3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART3EN)) == RESET) -#define __HAL_RCC_UART4_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART4EN)) == RESET) -#define __HAL_RCC_UART5_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART5EN)) == RESET) -#define __HAL_RCC_CAN1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN1EN)) == RESET) -#define __HAL_RCC_CAN2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN2EN)) == RESET) -#define __HAL_RCC_DAC_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_DACEN)) == RESET) -#define __HAL_RCC_UART7_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART7EN)) == RESET) -#define __HAL_RCC_UART8_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART8EN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable - * @brief Enable or disable the High Speed APB (APB2) peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM8_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_ADC2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_ADC3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI5_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI5EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI5EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI6_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI6EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI6EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SAI1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SDIO_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI4_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM10_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN)) -#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN)) -#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN)) -#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN)) -#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN)) -#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN)) -#define __HAL_RCC_SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN)) -#define __HAL_RCC_SPI6_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI6EN)) -#define __HAL_RCC_SAI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI1EN)) - -#if defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) -#define __HAL_RCC_LTDC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_LTDCEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_LTDCEN);\ - UNUSED(tmpreg); \ - } while(0) - -#define __HAL_RCC_LTDC_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_LTDCEN)) -#endif /* STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F469xx) || defined(STM32F479xx) -#define __HAL_RCC_DSI_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_DSIEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_DSIEN);\ - UNUSED(tmpreg); \ - } while(0) - -#define __HAL_RCC_DSI_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_DSIEN)) -#endif /* STM32F469xx || STM32F479xx */ -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Peripheral_Clock_Enable_Disable_Status APB2 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM8_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM8EN)) != RESET) -#define __HAL_RCC_ADC2_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC2EN)) != RESET) -#define __HAL_RCC_ADC3_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC3EN)) != RESET) -#define __HAL_RCC_SPI5_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI5EN)) != RESET) -#define __HAL_RCC_SPI6_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI6EN)) != RESET) -#define __HAL_RCC_SAI1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SAI1EN)) != RESET) -#define __HAL_RCC_SDIO_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SDIOEN)) != RESET) -#define __HAL_RCC_SPI4_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI4EN)) != RESET) -#define __HAL_RCC_TIM10_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM10EN))!= RESET) - -#define __HAL_RCC_SDIO_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SDIOEN)) == RESET) -#define __HAL_RCC_SPI4_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI4EN)) == RESET) -#define __HAL_RCC_TIM10_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM10EN))== RESET) -#define __HAL_RCC_TIM8_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM8EN)) == RESET) -#define __HAL_RCC_ADC2_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC2EN)) == RESET) -#define __HAL_RCC_ADC3_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC3EN)) == RESET) -#define __HAL_RCC_SPI5_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI5EN)) == RESET) -#define __HAL_RCC_SPI6_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI6EN)) == RESET) -#define __HAL_RCC_SAI1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SAI1EN)) == RESET) - -#if defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) -#define __HAL_RCC_LTDC_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_LTDCEN)) != RESET) -#define __HAL_RCC_LTDC_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_LTDCEN)) == RESET) -#endif /* STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F469xx) || defined(STM32F479xx) -#define __HAL_RCC_DSI_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_DSIEN)) != RESET) -#define __HAL_RCC_DSI_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_DSIEN)) == RESET) -#endif /* STM32F469xx || STM32F479xx */ -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset - * @brief Force or release AHB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST)) -#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST)) -#define __HAL_RCC_GPIOF_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOFRST)) -#define __HAL_RCC_GPIOG_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOGRST)) -#define __HAL_RCC_GPIOI_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOIRST)) -#define __HAL_RCC_ETHMAC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_ETHMACRST)) -#define __HAL_RCC_USB_OTG_HS_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_OTGHRST)) -#define __HAL_RCC_GPIOJ_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOJRST)) -#define __HAL_RCC_GPIOK_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOKRST)) -#define __HAL_RCC_DMA2D_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_DMA2DRST)) -#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST)) - -#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST)) -#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST)) -#define __HAL_RCC_GPIOF_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOFRST)) -#define __HAL_RCC_GPIOG_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOGRST)) -#define __HAL_RCC_GPIOI_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOIRST)) -#define __HAL_RCC_ETHMAC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_ETHMACRST)) -#define __HAL_RCC_USB_OTG_HS_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_OTGHRST)) -#define __HAL_RCC_GPIOJ_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOJRST)) -#define __HAL_RCC_GPIOK_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOKRST)) -#define __HAL_RCC_DMA2D_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_DMA2DRST)) -#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset - * @brief Force or release AHB2 peripheral reset. - * @{ - */ -#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST)) -#define __HAL_RCC_RNG_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_RNGRST)) -#define __HAL_RCC_DCMI_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_DCMIRST)) - -#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00U) -#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST)) -#define __HAL_RCC_RNG_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_RNGRST)) -#define __HAL_RCC_DCMI_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_DCMIRST)) - -#if defined(STM32F437xx)|| defined(STM32F439xx) || defined(STM32F479xx) -#define __HAL_RCC_CRYP_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_CRYPRST)) -#define __HAL_RCC_HASH_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_HASHRST)) - -#define __HAL_RCC_CRYP_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_CRYPRST)) -#define __HAL_RCC_HASH_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_HASHRST)) -#endif /* STM32F437xx || STM32F439xx || STM32F479xx */ -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset - * @brief Force or release AHB3 peripheral reset. - * @{ - */ -#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00U) -#define __HAL_RCC_FMC_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_FMCRST)) -#define __HAL_RCC_FMC_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_FMCRST)) - -#if defined(STM32F469xx) || defined(STM32F479xx) -#define __HAL_RCC_QSPI_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_QSPIRST)) -#define __HAL_RCC_QSPI_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_QSPIRST)) -#endif /* STM32F469xx || STM32F479xx */ -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset - * @brief Force or release APB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST)) -#define __HAL_RCC_TIM7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM7RST)) -#define __HAL_RCC_TIM12_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM12RST)) -#define __HAL_RCC_TIM13_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM13RST)) -#define __HAL_RCC_TIM14_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM14RST)) -#define __HAL_RCC_USART3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USART3RST)) -#define __HAL_RCC_UART4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART4RST)) -#define __HAL_RCC_UART5_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART5RST)) -#define __HAL_RCC_CAN1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN1RST)) -#define __HAL_RCC_CAN2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN2RST)) -#define __HAL_RCC_DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST)) -#define __HAL_RCC_UART7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART7RST)) -#define __HAL_RCC_UART8_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART8RST)) -#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST)) -#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST)) -#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST)) -#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST)) -#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST)) - -#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST)) -#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST)) -#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST)) -#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST)) -#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST)) -#define __HAL_RCC_TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST)) -#define __HAL_RCC_TIM7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM7RST)) -#define __HAL_RCC_TIM12_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM12RST)) -#define __HAL_RCC_TIM13_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM13RST)) -#define __HAL_RCC_TIM14_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM14RST)) -#define __HAL_RCC_USART3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_USART3RST)) -#define __HAL_RCC_UART4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART4RST)) -#define __HAL_RCC_UART5_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART5RST)) -#define __HAL_RCC_CAN1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN1RST)) -#define __HAL_RCC_CAN2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN2RST)) -#define __HAL_RCC_DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST)) -#define __HAL_RCC_UART7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART7RST)) -#define __HAL_RCC_UART8_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART8RST)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset - * @brief Force or release APB2 peripheral reset. - * @{ - */ -#define __HAL_RCC_TIM8_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM8RST)) -#define __HAL_RCC_SPI5_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI5RST)) -#define __HAL_RCC_SPI6_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI6RST)) -#define __HAL_RCC_SAI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SAI1RST)) -#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST)) -#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST)) -#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST)) - -#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST)) -#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST)) -#define __HAL_RCC_TIM10_RELEASE_RESET()(RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST)) -#define __HAL_RCC_TIM8_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM8RST)) -#define __HAL_RCC_SPI5_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI5RST)) -#define __HAL_RCC_SPI6_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI6RST)) -#define __HAL_RCC_SAI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SAI1RST)) - -#if defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) -#define __HAL_RCC_LTDC_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_LTDCRST)) -#define __HAL_RCC_LTDC_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_LTDCRST)) -#endif /* STM32F429xx|| STM32F439xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F469xx) || defined(STM32F479xx) -#define __HAL_RCC_DSI_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_DSIRST)) -#define __HAL_RCC_DSI_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_DSIRST)) -#endif /* STM32F469xx || STM32F479xx */ -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN)) -#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN)) -#define __HAL_RCC_GPIOF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOFLPEN)) -#define __HAL_RCC_GPIOG_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOGLPEN)) -#define __HAL_RCC_GPIOI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOILPEN)) -#define __HAL_RCC_SRAM2_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM2LPEN)) -#define __HAL_RCC_ETHMAC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACLPEN)) -#define __HAL_RCC_ETHMACTX_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACTXLPEN)) -#define __HAL_RCC_ETHMACRX_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACRXLPEN)) -#define __HAL_RCC_ETHMACPTP_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACPTPLPEN)) -#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSLPEN)) -#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSULPILPEN)) -#define __HAL_RCC_GPIOJ_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOJLPEN)) -#define __HAL_RCC_GPIOK_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOKLPEN)) -#define __HAL_RCC_SRAM3_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM3LPEN)) -#define __HAL_RCC_DMA2D_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_DMA2DLPEN)) -#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN)) -#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN)) -#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN)) -#define __HAL_RCC_BKPSRAM_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_BKPSRAMLPEN)) - -#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN)) -#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN)) -#define __HAL_RCC_GPIOF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOFLPEN)) -#define __HAL_RCC_GPIOG_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOGLPEN)) -#define __HAL_RCC_GPIOI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOILPEN)) -#define __HAL_RCC_SRAM2_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM2LPEN)) -#define __HAL_RCC_ETHMAC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACLPEN)) -#define __HAL_RCC_ETHMACTX_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACTXLPEN)) -#define __HAL_RCC_ETHMACRX_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACRXLPEN)) -#define __HAL_RCC_ETHMACPTP_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACPTPLPEN)) -#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSLPEN)) -#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSULPILPEN)) -#define __HAL_RCC_GPIOJ_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOJLPEN)) -#define __HAL_RCC_GPIOK_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOKLPEN)) -#define __HAL_RCC_DMA2D_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_DMA2DLPEN)) -#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN)) -#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN)) -#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN)) -#define __HAL_RCC_BKPSRAM_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_BKPSRAMLPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN)) -#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN)) - -#define __HAL_RCC_RNG_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_RNGLPEN)) -#define __HAL_RCC_RNG_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_RNGLPEN)) - -#define __HAL_RCC_DCMI_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_DCMILPEN)) -#define __HAL_RCC_DCMI_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_DCMILPEN)) - -#if defined(STM32F437xx)|| defined(STM32F439xx) || defined(STM32F479xx) -#define __HAL_RCC_CRYP_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_CRYPLPEN)) -#define __HAL_RCC_HASH_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_HASHLPEN)) - -#define __HAL_RCC_CRYP_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_CRYPLPEN)) -#define __HAL_RCC_HASH_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_HASHLPEN)) -#endif /* STM32F437xx || STM32F439xx || STM32F479xx */ -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_LowPower_Enable_Disable AHB3 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_FMC_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_FMCLPEN)) -#define __HAL_RCC_FMC_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_FMCLPEN)) - -#if defined(STM32F469xx) || defined(STM32F479xx) -#define __HAL_RCC_QSPI_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_QSPILPEN)) -#define __HAL_RCC_QSPI_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_QSPILPEN)) -#endif /* STM32F469xx || STM32F479xx */ -/** - * @} - */ - -/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_TIM6_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM6LPEN)) -#define __HAL_RCC_TIM7_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM7LPEN)) -#define __HAL_RCC_TIM12_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM12LPEN)) -#define __HAL_RCC_TIM13_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM13LPEN)) -#define __HAL_RCC_TIM14_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM14LPEN)) -#define __HAL_RCC_USART3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_USART3LPEN)) -#define __HAL_RCC_UART4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART4LPEN)) -#define __HAL_RCC_UART5_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART5LPEN)) -#define __HAL_RCC_CAN1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN1LPEN)) -#define __HAL_RCC_CAN2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN2LPEN)) -#define __HAL_RCC_DAC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_DACLPEN)) -#define __HAL_RCC_UART7_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART7LPEN)) -#define __HAL_RCC_UART8_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART8LPEN)) -#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN)) -#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN)) -#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN)) -#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN)) -#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN)) - -#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN)) -#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN)) -#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN)) -#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN)) -#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN)) -#define __HAL_RCC_TIM6_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM6LPEN)) -#define __HAL_RCC_TIM7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM7LPEN)) -#define __HAL_RCC_TIM12_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM12LPEN)) -#define __HAL_RCC_TIM13_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM13LPEN)) -#define __HAL_RCC_TIM14_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM14LPEN)) -#define __HAL_RCC_USART3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_USART3LPEN)) -#define __HAL_RCC_UART4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART4LPEN)) -#define __HAL_RCC_UART5_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART5LPEN)) -#define __HAL_RCC_CAN1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN1LPEN)) -#define __HAL_RCC_CAN2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN2LPEN)) -#define __HAL_RCC_DAC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_DACLPEN)) -#define __HAL_RCC_UART7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART7LPEN)) -#define __HAL_RCC_UART8_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART8LPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_TIM8_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM8LPEN)) -#define __HAL_RCC_ADC2_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC2LPEN)) -#define __HAL_RCC_ADC3_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC3LPEN)) -#define __HAL_RCC_SPI5_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI5LPEN)) -#define __HAL_RCC_SPI6_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI6LPEN)) -#define __HAL_RCC_SAI1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SAI1LPEN)) -#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN)) -#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN)) -#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE()(RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN)) - -#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN)) -#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN)) -#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE()(RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN)) -#define __HAL_RCC_TIM8_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM8LPEN)) -#define __HAL_RCC_ADC2_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC2LPEN)) -#define __HAL_RCC_ADC3_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC3LPEN)) -#define __HAL_RCC_SPI5_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI5LPEN)) -#define __HAL_RCC_SPI6_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI6LPEN)) -#define __HAL_RCC_SAI1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SAI1LPEN)) - -#if defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) -#define __HAL_RCC_LTDC_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_LTDCLPEN)) - -#define __HAL_RCC_LTDC_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_LTDCLPEN)) -#endif /* STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F469xx) || defined(STM32F479xx) -#define __HAL_RCC_DSI_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_DSILPEN)) -#define __HAL_RCC_DSI_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_DSILPEN)) -#endif /* STM32F469xx || STM32F479xx */ -/** - * @} - */ -#endif /* STM32F427xx || STM32F437xx || STM32F429xx|| STM32F439xx || STM32F469xx || STM32F479xx */ -/*----------------------------------------------------------------------------*/ - -/*----------------------------------- STM32F40xxx/STM32F41xxx-----------------*/ -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx) -/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable - * @brief Enables or disables the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_BKPSRAM_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CCMDATARAMEN_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CRC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOI_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOIEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOIEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOF_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOFEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOFEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOG_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOGEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOGEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_USB_OTG_HS_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSULPIEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSULPIEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN)) -#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN)) -#define __HAL_RCC_GPIOF_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOFEN)) -#define __HAL_RCC_GPIOG_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOGEN)) -#define __HAL_RCC_GPIOI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOIEN)) -#define __HAL_RCC_USB_OTG_HS_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSEN)) -#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSULPIEN)) -#define __HAL_RCC_BKPSRAM_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_BKPSRAMEN)) -#define __HAL_RCC_CCMDATARAMEN_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CCMDATARAMEN)) -#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN)) -#if defined(STM32F407xx)|| defined(STM32F417xx) -/** - * @brief Enable ETHERNET clock. - */ -#define __HAL_RCC_ETHMAC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_ETHMACTX_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACTXEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACTXEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_ETHMACRX_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACRXEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACRXEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_ETHMACPTP_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACPTPEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_ETHMACPTPEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_ETH_CLK_ENABLE() do { \ - __HAL_RCC_ETHMAC_CLK_ENABLE(); \ - __HAL_RCC_ETHMACTX_CLK_ENABLE(); \ - __HAL_RCC_ETHMACRX_CLK_ENABLE(); \ - } while(0) - -/** - * @brief Disable ETHERNET clock. - */ -#define __HAL_RCC_ETHMAC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACEN)) -#define __HAL_RCC_ETHMACTX_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACTXEN)) -#define __HAL_RCC_ETHMACRX_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACRXEN)) -#define __HAL_RCC_ETHMACPTP_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACPTPEN)) -#define __HAL_RCC_ETH_CLK_DISABLE() do { \ - __HAL_RCC_ETHMACTX_CLK_DISABLE(); \ - __HAL_RCC_ETHMACRX_CLK_DISABLE(); \ - __HAL_RCC_ETHMAC_CLK_DISABLE(); \ - } while(0) -#endif /* STM32F407xx || STM32F417xx */ -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_Peripheral_Clock_Enable_Disable_Status AHB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_BKPSRAM_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_BKPSRAMEN)) != RESET) -#define __HAL_RCC_CCMDATARAMEN_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CCMDATARAMEN)) != RESET) -#define __HAL_RCC_CRC_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CRCEN)) != RESET) -#define __HAL_RCC_GPIOD_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIODEN)) != RESET) -#define __HAL_RCC_GPIOE_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOEEN)) != RESET) -#define __HAL_RCC_GPIOI_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOIEN)) != RESET) -#define __HAL_RCC_GPIOF_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOFEN)) != RESET) -#define __HAL_RCC_GPIOG_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOGEN)) != RESET) -#define __HAL_RCC_USB_OTG_HS_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_OTGHSEN)) != RESET) -#define __HAL_RCC_USB_OTG_HS_ULPI_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_OTGHSULPIEN)) != RESET) - -#define __HAL_RCC_GPIOD_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIODEN)) == RESET) -#define __HAL_RCC_GPIOE_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOEEN)) == RESET) -#define __HAL_RCC_GPIOF_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOFEN)) == RESET) -#define __HAL_RCC_GPIOG_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOGEN)) == RESET) -#define __HAL_RCC_GPIOI_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOIEN)) == RESET) -#define __HAL_RCC_USB_OTG_HS_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_OTGHSEN)) == RESET) -#define __HAL_RCC_USB_OTG_HS_ULPI_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_OTGHSULPIEN))== RESET) -#define __HAL_RCC_BKPSRAM_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_BKPSRAMEN)) == RESET) -#define __HAL_RCC_CCMDATARAMEN_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CCMDATARAMEN)) == RESET) -#define __HAL_RCC_CRC_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CRCEN)) == RESET) -#if defined(STM32F407xx)|| defined(STM32F417xx) -/** - * @brief Enable ETHERNET clock. - */ -#define __HAL_RCC_ETHMAC_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACEN)) != RESET) -#define __HAL_RCC_ETHMACTX_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACTXEN)) != RESET) -#define __HAL_RCC_ETHMACRX_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACRXEN)) != RESET) -#define __HAL_RCC_ETHMACPTP_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACPTPEN)) != RESET) -#define __HAL_RCC_ETH_IS_CLK_ENABLED() (__HAL_RCC_ETHMAC_IS_CLK_ENABLED() && \ - __HAL_RCC_ETHMACTX_IS_CLK_ENABLED() && \ - __HAL_RCC_ETHMACRX_IS_CLK_ENABLED()) -/** - * @brief Disable ETHERNET clock. - */ -#define __HAL_RCC_ETHMAC_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACEN)) == RESET) -#define __HAL_RCC_ETHMACTX_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACTXEN)) == RESET) -#define __HAL_RCC_ETHMACRX_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACRXEN)) == RESET) -#define __HAL_RCC_ETHMACPTP_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_ETHMACPTPEN)) == RESET) -#define __HAL_RCC_ETH_IS_CLK_DISABLED() (__HAL_RCC_ETHMAC_IS_CLK_DISABLED() && \ - __HAL_RCC_ETHMACTX_IS_CLK_DISABLED() && \ - __HAL_RCC_ETHMACRX_IS_CLK_DISABLED()) -#endif /* STM32F407xx || STM32F417xx */ -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable - * @brief Enable or disable the AHB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\ - __HAL_RCC_SYSCFG_CLK_ENABLE();\ - }while(0) - -#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN)) - -#define __HAL_RCC_RNG_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_RNG_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_RNGEN)) - -#if defined(STM32F407xx)|| defined(STM32F417xx) -#define __HAL_RCC_DCMI_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_DCMIEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_DCMIEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_DCMI_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_DCMIEN)) -#endif /* STM32F407xx || STM32F417xx */ - -#if defined(STM32F415xx) || defined(STM32F417xx) -#define __HAL_RCC_CRYP_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_CRYPEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_CRYPEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_HASH_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_HASHEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_HASHEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CRYP_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_CRYPEN)) -#define __HAL_RCC_HASH_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_HASHEN)) -#endif /* STM32F415xx || STM32F417xx */ -/** - * @} - */ - - -/** @defgroup RCCEx_AHB2_Peripheral_Clock_Enable_Disable_Status AHB2 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_USB_OTG_FS_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_OTGFSEN)) != RESET) -#define __HAL_RCC_USB_OTG_FS_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_OTGFSEN)) == RESET) - -#define __HAL_RCC_RNG_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_RNGEN)) != RESET) -#define __HAL_RCC_RNG_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_RNGEN)) == RESET) - -#if defined(STM32F407xx)|| defined(STM32F417xx) -#define __HAL_RCC_DCMI_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_DCMIEN)) != RESET) -#define __HAL_RCC_DCMI_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_DCMIEN)) == RESET) -#endif /* STM32F407xx || STM32F417xx */ - -#if defined(STM32F415xx) || defined(STM32F417xx) -#define __HAL_RCC_CRYP_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_CRYPEN)) != RESET) -#define __HAL_RCC_HASH_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_HASHEN)) != RESET) - -#define __HAL_RCC_CRYP_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_CRYPEN)) == RESET) -#define __HAL_RCC_HASH_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_HASHEN)) == RESET) -#endif /* STM32F415xx || STM32F417xx */ -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_Clock_Enable_Disable AHB3 Peripheral Clock Enable Disable - * @brief Enables or disables the AHB3 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_FSMC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_FSMC_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_FSMCEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_Peripheral_Clock_Enable_Disable_Status AHB3 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB3 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_FSMC_IS_CLK_ENABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_FSMCEN)) != RESET) -#define __HAL_RCC_FSMC_IS_CLK_DISABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_FSMCEN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable - * @brief Enable or disable the Low Speed APB (APB1) peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM6_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM7_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM7EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM7EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM12_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM12EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM12EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM13_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM13EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM13EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM14_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_USART3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_USART3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_USART3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_UART4_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_UART4EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_UART4EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_UART5_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_UART5EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_UART5EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CAN1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CAN2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_DAC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM4_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_I2C3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN)) -#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN)) -#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN)) -#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN)) -#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN)) -#define __HAL_RCC_TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN)) -#define __HAL_RCC_TIM7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM7EN)) -#define __HAL_RCC_TIM12_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM12EN)) -#define __HAL_RCC_TIM13_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM13EN)) -#define __HAL_RCC_TIM14_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM14EN)) -#define __HAL_RCC_USART3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_USART3EN)) -#define __HAL_RCC_UART4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART4EN)) -#define __HAL_RCC_UART5_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART5EN)) -#define __HAL_RCC_CAN1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN1EN)) -#define __HAL_RCC_CAN2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN2EN)) -#define __HAL_RCC_DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Peripheral_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) != RESET) -#define __HAL_RCC_TIM3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) != RESET) -#define __HAL_RCC_TIM4_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM4EN)) != RESET) -#define __HAL_RCC_SPI3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) != RESET) -#define __HAL_RCC_I2C3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C3EN)) != RESET) -#define __HAL_RCC_TIM6_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM6EN)) != RESET) -#define __HAL_RCC_TIM7_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM7EN)) != RESET) -#define __HAL_RCC_TIM12_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM12EN)) != RESET) -#define __HAL_RCC_TIM13_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM13EN)) != RESET) -#define __HAL_RCC_TIM14_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM14EN)) != RESET) -#define __HAL_RCC_USART3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART3EN)) != RESET) -#define __HAL_RCC_UART4_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART4EN)) != RESET) -#define __HAL_RCC_UART5_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART5EN)) != RESET) -#define __HAL_RCC_CAN1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN1EN)) != RESET) -#define __HAL_RCC_CAN2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN2EN)) != RESET) -#define __HAL_RCC_DAC_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_DACEN)) != RESET) - -#define __HAL_RCC_TIM2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) == RESET) -#define __HAL_RCC_TIM3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) == RESET) -#define __HAL_RCC_TIM4_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM4EN)) == RESET) -#define __HAL_RCC_SPI3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) == RESET) -#define __HAL_RCC_I2C3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C3EN)) == RESET) -#define __HAL_RCC_TIM6_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM6EN)) == RESET) -#define __HAL_RCC_TIM7_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM7EN)) == RESET) -#define __HAL_RCC_TIM12_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM12EN)) == RESET) -#define __HAL_RCC_TIM13_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM13EN)) == RESET) -#define __HAL_RCC_TIM14_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM14EN)) == RESET) -#define __HAL_RCC_USART3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART3EN)) == RESET) -#define __HAL_RCC_UART4_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART4EN)) == RESET) -#define __HAL_RCC_UART5_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART5EN)) == RESET) -#define __HAL_RCC_CAN1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN1EN)) == RESET) -#define __HAL_RCC_CAN2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN2EN)) == RESET) -#define __HAL_RCC_DAC_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_DACEN)) == RESET) -/** -* @} -*/ - -/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable - * @brief Enable or disable the High Speed APB (APB2) peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM8_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_ADC2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_ADC3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SDIO_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI4_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM10_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\ - UNUSED(tmpreg); \ - } while(0) - -#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN)) -#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN)) -#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN)) -#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN)) -#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN)) -#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Peripheral_Clock_Enable_Disable_Status APB2 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_SDIO_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SDIOEN)) != RESET) -#define __HAL_RCC_SPI4_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI4EN)) != RESET) -#define __HAL_RCC_TIM10_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM10EN)) != RESET) -#define __HAL_RCC_TIM8_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM8EN)) != RESET) -#define __HAL_RCC_ADC2_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC2EN)) != RESET) -#define __HAL_RCC_ADC3_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC3EN)) != RESET) - -#define __HAL_RCC_SDIO_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SDIOEN)) == RESET) -#define __HAL_RCC_SPI4_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI4EN)) == RESET) -#define __HAL_RCC_TIM10_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM10EN)) == RESET) -#define __HAL_RCC_TIM8_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM8EN)) == RESET) -#define __HAL_RCC_ADC2_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC2EN)) == RESET) -#define __HAL_RCC_ADC3_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC3EN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset - * @brief Force or release AHB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST)) -#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST)) -#define __HAL_RCC_GPIOF_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOFRST)) -#define __HAL_RCC_GPIOG_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOGRST)) -#define __HAL_RCC_GPIOI_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOIRST)) -#define __HAL_RCC_ETHMAC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_ETHMACRST)) -#define __HAL_RCC_USB_OTG_HS_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_OTGHRST)) -#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST)) - -#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST)) -#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST)) -#define __HAL_RCC_GPIOF_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOFRST)) -#define __HAL_RCC_GPIOG_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOGRST)) -#define __HAL_RCC_GPIOI_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOIRST)) -#define __HAL_RCC_ETHMAC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_ETHMACRST)) -#define __HAL_RCC_USB_OTG_HS_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_OTGHRST)) -#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset - * @brief Force or release AHB2 peripheral reset. - * @{ - */ -#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00U) - -#if defined(STM32F407xx)|| defined(STM32F417xx) -#define __HAL_RCC_DCMI_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_DCMIRST)) -#define __HAL_RCC_DCMI_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_DCMIRST)) -#endif /* STM32F407xx || STM32F417xx */ - -#if defined(STM32F415xx) || defined(STM32F417xx) -#define __HAL_RCC_CRYP_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_CRYPRST)) -#define __HAL_RCC_HASH_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_HASHRST)) - -#define __HAL_RCC_CRYP_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_CRYPRST)) -#define __HAL_RCC_HASH_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_HASHRST)) -#endif /* STM32F415xx || STM32F417xx */ - -#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST)) -#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST)) - -#define __HAL_RCC_RNG_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_RNGRST)) -#define __HAL_RCC_RNG_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_RNGRST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset - * @brief Force or release AHB3 peripheral reset. - * @{ - */ -#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00U) - -#define __HAL_RCC_FSMC_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_FSMCRST)) -#define __HAL_RCC_FSMC_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_FSMCRST)) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset - * @brief Force or release APB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST)) -#define __HAL_RCC_TIM7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM7RST)) -#define __HAL_RCC_TIM12_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM12RST)) -#define __HAL_RCC_TIM13_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM13RST)) -#define __HAL_RCC_TIM14_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM14RST)) -#define __HAL_RCC_USART3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USART3RST)) -#define __HAL_RCC_UART4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART4RST)) -#define __HAL_RCC_UART5_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART5RST)) -#define __HAL_RCC_CAN1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN1RST)) -#define __HAL_RCC_CAN2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN2RST)) -#define __HAL_RCC_DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST)) -#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST)) -#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST)) -#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST)) -#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST)) -#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST)) - -#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST)) -#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST)) -#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST)) -#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST)) -#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST)) -#define __HAL_RCC_TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST)) -#define __HAL_RCC_TIM7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM7RST)) -#define __HAL_RCC_TIM12_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM12RST)) -#define __HAL_RCC_TIM13_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM13RST)) -#define __HAL_RCC_TIM14_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM14RST)) -#define __HAL_RCC_USART3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_USART3RST)) -#define __HAL_RCC_UART4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART4RST)) -#define __HAL_RCC_UART5_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART5RST)) -#define __HAL_RCC_CAN1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN1RST)) -#define __HAL_RCC_CAN2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN2RST)) -#define __HAL_RCC_DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset - * @brief Force or release APB2 peripheral reset. - * @{ - */ -#define __HAL_RCC_TIM8_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM8RST)) -#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST)) -#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST)) -#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST)) - -#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST)) -#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST)) -#define __HAL_RCC_TIM10_RELEASE_RESET()(RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST)) -#define __HAL_RCC_TIM8_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM8RST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN)) -#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN)) -#define __HAL_RCC_GPIOF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOFLPEN)) -#define __HAL_RCC_GPIOG_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOGLPEN)) -#define __HAL_RCC_GPIOI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOILPEN)) -#define __HAL_RCC_SRAM2_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM2LPEN)) -#define __HAL_RCC_ETHMAC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACLPEN)) -#define __HAL_RCC_ETHMACTX_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACTXLPEN)) -#define __HAL_RCC_ETHMACRX_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACRXLPEN)) -#define __HAL_RCC_ETHMACPTP_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACPTPLPEN)) -#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSLPEN)) -#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSULPILPEN)) -#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN)) -#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN)) -#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN)) -#define __HAL_RCC_BKPSRAM_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_BKPSRAMLPEN)) - -#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN)) -#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN)) -#define __HAL_RCC_GPIOF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOFLPEN)) -#define __HAL_RCC_GPIOG_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOGLPEN)) -#define __HAL_RCC_GPIOI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOILPEN)) -#define __HAL_RCC_SRAM2_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM2LPEN)) -#define __HAL_RCC_ETHMAC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACLPEN)) -#define __HAL_RCC_ETHMACTX_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACTXLPEN)) -#define __HAL_RCC_ETHMACRX_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACRXLPEN)) -#define __HAL_RCC_ETHMACPTP_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACPTPLPEN)) -#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSLPEN)) -#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSULPILPEN)) -#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN)) -#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN)) -#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN)) -#define __HAL_RCC_BKPSRAM_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_BKPSRAMLPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN)) -#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN)) - -#define __HAL_RCC_RNG_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_RNGLPEN)) -#define __HAL_RCC_RNG_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_RNGLPEN)) - -#if defined(STM32F407xx)|| defined(STM32F417xx) -#define __HAL_RCC_DCMI_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_DCMILPEN)) -#define __HAL_RCC_DCMI_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_DCMILPEN)) -#endif /* STM32F407xx || STM32F417xx */ - -#if defined(STM32F415xx) || defined(STM32F417xx) -#define __HAL_RCC_CRYP_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_CRYPLPEN)) -#define __HAL_RCC_HASH_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_HASHLPEN)) - -#define __HAL_RCC_CRYP_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_CRYPLPEN)) -#define __HAL_RCC_HASH_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_HASHLPEN)) -#endif /* STM32F415xx || STM32F417xx */ -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_LowPower_Enable_Disable AHB3 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_FSMC_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_FSMCLPEN)) -#define __HAL_RCC_FSMC_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_FSMCLPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_TIM6_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM6LPEN)) -#define __HAL_RCC_TIM7_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM7LPEN)) -#define __HAL_RCC_TIM12_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM12LPEN)) -#define __HAL_RCC_TIM13_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM13LPEN)) -#define __HAL_RCC_TIM14_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM14LPEN)) -#define __HAL_RCC_USART3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_USART3LPEN)) -#define __HAL_RCC_UART4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART4LPEN)) -#define __HAL_RCC_UART5_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART5LPEN)) -#define __HAL_RCC_CAN1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN1LPEN)) -#define __HAL_RCC_CAN2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN2LPEN)) -#define __HAL_RCC_DAC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_DACLPEN)) -#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN)) -#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN)) -#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN)) -#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN)) -#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN)) - -#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN)) -#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN)) -#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN)) -#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN)) -#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN)) -#define __HAL_RCC_TIM6_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM6LPEN)) -#define __HAL_RCC_TIM7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM7LPEN)) -#define __HAL_RCC_TIM12_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM12LPEN)) -#define __HAL_RCC_TIM13_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM13LPEN)) -#define __HAL_RCC_TIM14_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM14LPEN)) -#define __HAL_RCC_USART3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_USART3LPEN)) -#define __HAL_RCC_UART4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART4LPEN)) -#define __HAL_RCC_UART5_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART5LPEN)) -#define __HAL_RCC_CAN1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN1LPEN)) -#define __HAL_RCC_CAN2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN2LPEN)) -#define __HAL_RCC_DAC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_DACLPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_TIM8_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM8LPEN)) -#define __HAL_RCC_ADC2_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC2LPEN)) -#define __HAL_RCC_ADC3_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC3LPEN)) -#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN)) -#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN)) -#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE()(RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN)) - -#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN)) -#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN)) -#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE()(RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN)) -#define __HAL_RCC_TIM8_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM8LPEN)) -#define __HAL_RCC_ADC2_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC2LPEN)) -#define __HAL_RCC_ADC3_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC3LPEN)) -/** - * @} - */ -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx */ -/*----------------------------------------------------------------------------*/ - -/*------------------------- STM32F401xE/STM32F401xC --------------------------*/ -#if defined(STM32F401xC) || defined(STM32F401xE) -/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable - * @brief Enable or disable the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CRC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_BKPSRAM_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CCMDATARAMEN_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\ - UNUSED(tmpreg); \ - } while(0) - -#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN)) -#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN)) -#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN)) -#define __HAL_RCC_BKPSRAM_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_BKPSRAMEN)) -#define __HAL_RCC_CCMDATARAMEN_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CCMDATARAMEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_Peripheral_Clock_Enable_Disable_Status AHB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_GPIOD_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIODEN)) != RESET) -#define __HAL_RCC_GPIOE_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOEEN)) != RESET) -#define __HAL_RCC_CRC_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CRCEN)) != RESET) -#define __HAL_RCC_BKPSRAM_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_BKPSRAMEN)) != RESET) -#define __HAL_RCC_CCMDATARAMEN_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CCMDATARAMEN)) != RESET) - -#define __HAL_RCC_GPIOD_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIODEN)) == RESET) -#define __HAL_RCC_GPIOE_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOEEN)) == RESET) -#define __HAL_RCC_CRC_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CRCEN)) == RESET) -#define __HAL_RCC_BKPSRAM_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_BKPSRAMEN)) == RESET) -#define __HAL_RCC_CCMDATARAMEN_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CCMDATARAMEN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable - * @brief Enable or disable the AHB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\ - __HAL_RCC_SYSCFG_CLK_ENABLE();\ - }while(0) - -#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Peripheral_Clock_Enable_Disable_Status AHB2 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_USB_OTG_FS_IS_CLK_ENABLED() (RCC->AHB2ENR & (RCC_AHB2ENR_OTGFSEN)) != RESET) -#define __HAL_RCC_USB_OTG_FS_IS_CLK_DISABLED() (RCC->AHB2ENR & (RCC_AHB2ENR_OTGFSEN)) == RESET) -/** - * @} - */ - -/** @defgroup RCC_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable - * @brief Enable or disable the Low Speed APB (APB1) peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM4_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_I2C3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN)) -#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN)) -#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN)) -#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN)) -#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Peripheral_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) != RESET) -#define __HAL_RCC_TIM3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) != RESET) -#define __HAL_RCC_TIM4_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM4EN)) != RESET) -#define __HAL_RCC_SPI3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) != RESET) -#define __HAL_RCC_I2C3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C3EN)) != RESET) - -#define __HAL_RCC_TIM2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) == RESET) -#define __HAL_RCC_TIM3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) == RESET) -#define __HAL_RCC_TIM4_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM4EN)) == RESET) -#define __HAL_RCC_SPI3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) == RESET) -#define __HAL_RCC_I2C3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C3EN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable - * @brief Enable or disable the High Speed APB (APB2) peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_SDIO_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI4_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM10_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\ - UNUSED(tmpreg); \ - } while(0) - -#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN)) -#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN)) -#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Peripheral_Clock_Enable_Disable_Status APB2 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_SDIO_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SDIOEN)) == RESET) -#define __HAL_RCC_SPI4_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI4EN)) == RESET) -#define __HAL_RCC_TIM10_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM10EN)) == RESET) -/** - * @} - */ -/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset - * @brief Force or release AHB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_AHB1_FORCE_RESET() (RCC->AHB1RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST)) -#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST)) -#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST)) - -#define __HAL_RCC_AHB1_RELEASE_RESET() (RCC->AHB1RSTR = 0x00U) -#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST)) -#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST)) -#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset - * @brief Force or release AHB2 peripheral reset. - * @{ - */ -#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST)) - -#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00U) -#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST)) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset - * @brief Force or release APB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_APB1_FORCE_RESET() (RCC->APB1RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST)) -#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST)) -#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST)) -#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST)) -#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST)) - -#define __HAL_RCC_APB1_RELEASE_RESET() (RCC->APB1RSTR = 0x00U) -#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST)) -#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST)) -#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST)) -#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST)) -#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset - * @brief Force or release APB2 peripheral reset. - * @{ - */ -#define __HAL_RCC_APB2_FORCE_RESET() (RCC->APB2RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST)) -#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST)) -#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST)) - -#define __HAL_RCC_APB2_RELEASE_RESET() (RCC->APB2RSTR = 0x00U) -#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST)) -#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST)) -#define __HAL_RCC_TIM10_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset - * @brief Force or release AHB3 peripheral reset. - * @{ - */ -#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00U) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN)) -#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN)) -#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN)) -#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN)) -#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN)) -#define __HAL_RCC_BKPSRAM_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_BKPSRAMLPEN)) - -#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN)) -#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN)) -#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN)) -#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN)) -#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN)) -#define __HAL_RCC_BKPSRAM_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_BKPSRAMLPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN)) - -#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN)) -#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN)) -#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN)) -#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN)) -#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN)) - -#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN)) -#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN)) -#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN)) -#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN)) -#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN)) -#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN)) -#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN)) - -#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN)) -#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN)) -#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN)) -/** - * @} - */ -#endif /* STM32F401xC || STM32F401xE*/ -/*----------------------------------------------------------------------------*/ - -/*-------------------------------- STM32F410xx -------------------------------*/ -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable - * @brief Enables or disables the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_CRC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_RNG_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_RNGEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_RNGEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN)) -#define __HAL_RCC_RNG_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_RNGEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_Peripheral_Clock_Enable_Disable_Status AHB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_CRC_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CRCEN)) == RESET) -#define __HAL_RCC_RNG_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_RNGEN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable - * @brief Enable or disable the High Speed APB (APB1) peripheral clock. - * @{ - */ -#define __HAL_RCC_TIM6_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_LPTIM1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_LPTIM1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_LPTIM1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_RTCAPB_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_RTCAPBEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_RTCAPBEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_FMPI2C1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_FMPI2C1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_FMPI2C1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_DAC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\ - UNUSED(tmpreg); \ - } while(0) - -#define __HAL_RCC_TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN)) -#define __HAL_RCC_RTCAPB_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_RTCAPBEN)) -#define __HAL_RCC_LPTIM1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_LPTIM1EN)) -#define __HAL_RCC_FMPI2C1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_FMPI2C1EN)) -#define __HAL_RCC_DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Peripheral_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM6_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM6EN)) != RESET) -#define __HAL_RCC_RTCAPB_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_RTCAPBEN)) != RESET) -#define __HAL_RCC_LPTIM1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_LPTIM1EN)) != RESET) -#define __HAL_RCC_FMPI2C1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_FMPI2C1EN)) != RESET) -#define __HAL_RCC_DAC_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_DACEN)) != RESET) - -#define __HAL_RCC_TIM6_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM6EN)) == RESET) -#define __HAL_RCC_RTCAPB_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_RTCAPBEN)) == RESET) -#define __HAL_RCC_LPTIM1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_LPTIM1EN)) == RESET) -#define __HAL_RCC_FMPI2C1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_FMPI2C1EN)) == RESET) -#define __HAL_RCC_DAC_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_DACEN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable - * @brief Enable or disable the High Speed APB (APB2) peripheral clock. - * @{ - */ -#define __HAL_RCC_SPI5_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI5EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI5EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_EXTIT_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_EXTITEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_EXTITEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN)) -#define __HAL_RCC_EXTIT_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_EXTITEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Peripheral_Clock_Enable_Disable_Status APB2 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_SPI5_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI5EN)) != RESET) -#define __HAL_RCC_EXTIT_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_EXTITEN)) != RESET) - -#define __HAL_RCC_SPI5_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI5EN)) == RESET) -#define __HAL_RCC_EXTIT_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_EXTITEN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset - * @brief Force or release AHB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST)) -#define __HAL_RCC_RNG_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_RNGRST)) -#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST)) -#define __HAL_RCC_RNG_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_RNGRST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset - * @brief Force or release AHB2 peripheral reset. - * @{ - */ -#define __HAL_RCC_AHB2_FORCE_RESET() -#define __HAL_RCC_AHB2_RELEASE_RESET() -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset - * @brief Force or release AHB3 peripheral reset. - * @{ - */ -#define __HAL_RCC_AHB3_FORCE_RESET() -#define __HAL_RCC_AHB3_RELEASE_RESET() -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset - * @brief Force or release APB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST)) -#define __HAL_RCC_LPTIM1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_LPTIM1RST)) -#define __HAL_RCC_FMPI2C1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_FMPI2C1RST)) -#define __HAL_RCC_DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST)) - -#define __HAL_RCC_TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST)) -#define __HAL_RCC_LPTIM1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_LPTIM1RST)) -#define __HAL_RCC_FMPI2C1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_FMPI2C1RST)) -#define __HAL_RCC_DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset - * @brief Force or release APB2 peripheral reset. - * @{ - */ -#define __HAL_RCC_SPI5_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI5RST)) -#define __HAL_RCC_SPI5_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI5RST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_RNG_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_RNGLPEN)) -#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN)) -#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN)) -#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN)) - -#define __HAL_RCC_RNG_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_RNGLPEN)) -#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN)) -#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN)) -#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode. - * @{ - */ -#define __HAL_RCC_TIM6_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM6LPEN)) -#define __HAL_RCC_LPTIM1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_LPTIM1LPEN)) -#define __HAL_RCC_RTCAPB_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_RTCAPBLPEN)) -#define __HAL_RCC_FMPI2C1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_FMPI2C1LPEN)) -#define __HAL_RCC_DAC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_DACLPEN)) - -#define __HAL_RCC_TIM6_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM6LPEN)) -#define __HAL_RCC_LPTIM1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_LPTIM1LPEN)) -#define __HAL_RCC_RTCAPB_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_RTCAPBLPEN)) -#define __HAL_RCC_FMPI2C1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_FMPI2C1LPEN)) -#define __HAL_RCC_DAC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_DACLPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode. - * @{ - */ -#define __HAL_RCC_SPI5_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI5LPEN)) -#define __HAL_RCC_EXTIT_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_EXTITLPEN)) -#define __HAL_RCC_SPI5_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI5LPEN)) -#define __HAL_RCC_EXTIT_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_EXTITLPEN)) -/** - * @} - */ - -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ -/*----------------------------------------------------------------------------*/ - -/*-------------------------------- STM32F411xx -------------------------------*/ -#if defined(STM32F411xE) -/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable - * @brief Enables or disables the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_BKPSRAM_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CCMDATARAMEN_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CRC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN)) -#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN)) -#define __HAL_RCC_BKPSRAM_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_BKPSRAMEN)) -#define __HAL_RCC_CCMDATARAMEN_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CCMDATARAMEN)) -#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_Peripheral_Clock_Enable_Disable_Status AHB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_GPIOD_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIODEN)) != RESET) -#define __HAL_RCC_GPIOE_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOEEN)) != RESET) -#define __HAL_RCC_BKPSRAM_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_BKPSRAMEN)) != RESET) -#define __HAL_RCC_CCMDATARAMEN_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CCMDATARAMEN)) != RESET) -#define __HAL_RCC_CRC_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CRCEN)) != RESET) - -#define __HAL_RCC_GPIOD_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIODEN)) == RESET) -#define __HAL_RCC_GPIOE_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOEEN)) == RESET) -#define __HAL_RCC_BKPSRAM_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_BKPSRAMEN)) == RESET) -#define __HAL_RCC_CCMDATARAMEN_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CCMDATARAMEN)) == RESET) -#define __HAL_RCC_CRC_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CRCEN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEX_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable - * @brief Enable or disable the AHB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\ - __HAL_RCC_SYSCFG_CLK_ENABLE();\ - }while(0) - -#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Peripheral_Clock_Enable_Disable_Status AHB2 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_USB_OTG_FS_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_OTGFSEN)) != RESET) -#define __HAL_RCC_USB_OTG_FS_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_OTGFSEN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable - * @brief Enable or disable the Low Speed APB (APB1) peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM4_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_I2C3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN)) -#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN)) -#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN)) -#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN)) -#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Peripheral_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) != RESET) -#define __HAL_RCC_TIM3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) != RESET) -#define __HAL_RCC_TIM4_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM4EN)) != RESET) -#define __HAL_RCC_SPI3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) != RESET) -#define __HAL_RCC_I2C3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C3EN)) != RESET) - -#define __HAL_RCC_TIM2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) == RESET) -#define __HAL_RCC_TIM3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) == RESET) -#define __HAL_RCC_TIM4_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM4EN)) == RESET) -#define __HAL_RCC_SPI3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) == RESET) -#define __HAL_RCC_I2C3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C3EN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable - * @brief Enable or disable the High Speed APB (APB2) peripheral clock. - * @{ - */ -#define __HAL_RCC_SPI5_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI5EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI5EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SDIO_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI4_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM10_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN)) -#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN)) -#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN)) -#define __HAL_RCC_SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Peripheral_Clock_Enable_Disable_Status APB2 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_SDIO_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SDIOEN)) != RESET) -#define __HAL_RCC_SPI4_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI4EN)) != RESET) -#define __HAL_RCC_TIM10_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM10EN)) != RESET) -#define __HAL_RCC_SPI5_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI5EN)) != RESET) - -#define __HAL_RCC_SDIO_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SDIOEN)) == RESET) -#define __HAL_RCC_SPI4_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI4EN)) == RESET) -#define __HAL_RCC_TIM10_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM10EN)) == RESET) -#define __HAL_RCC_SPI5_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI5EN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset - * @brief Force or release AHB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST)) -#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST)) -#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST)) - -#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST)) -#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST)) -#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset - * @brief Force or release AHB2 peripheral reset. - * @{ - */ -#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST)) - -#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00U) -#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset - * @brief Force or release AHB3 peripheral reset. - * @{ - */ -#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00U) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset - * @brief Force or release APB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST)) -#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST)) -#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST)) -#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST)) -#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST)) - -#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST)) -#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST)) -#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST)) -#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST)) -#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset - * @brief Force or release APB2 peripheral reset. - * @{ - */ -#define __HAL_RCC_SPI5_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI5RST)) -#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST)) -#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST)) -#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST)) - -#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST)) -#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST)) -#define __HAL_RCC_TIM10_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST)) -#define __HAL_RCC_SPI5_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI5RST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN)) -#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN)) -#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN)) -#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN)) -#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN)) - -#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN)) -#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN)) -#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN)) -#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN)) -#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN)) -#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode. - * @{ - */ -#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN)) -#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN)) -#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN)) -#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN)) -#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN)) - -#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN)) -#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN)) -#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN)) -#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN)) -#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode. - * @{ - */ -#define __HAL_RCC_SPI5_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI5LPEN)) -#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN)) -#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN)) -#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN)) - -#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN)) -#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN)) -#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN)) -#define __HAL_RCC_SPI5_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI5LPEN)) -/** - * @} - */ -#endif /* STM32F411xE */ -/*----------------------------------------------------------------------------*/ - -/*---------------------------------- STM32F446xx -----------------------------*/ -#if defined(STM32F446xx) -/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable - * @brief Enables or disables the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_BKPSRAM_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CCMDATARAMEN_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CRC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOF_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOFEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOFEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOG_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOGEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOGEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_USB_OTG_HS_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSULPIEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSULPIEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN)) -#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN)) -#define __HAL_RCC_GPIOF_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOFEN)) -#define __HAL_RCC_GPIOG_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOGEN)) -#define __HAL_RCC_USB_OTG_HS_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSEN)) -#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSULPIEN)) -#define __HAL_RCC_BKPSRAM_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_BKPSRAMEN)) -#define __HAL_RCC_CCMDATARAMEN_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CCMDATARAMEN)) -#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_Peripheral_Clock_Enable_Disable_Status AHB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_GPIOD_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIODEN)) != RESET) -#define __HAL_RCC_GPIOE_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOEEN)) != RESET) -#define __HAL_RCC_GPIOF_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOFEN)) != RESET) -#define __HAL_RCC_GPIOG_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOGEN)) != RESET) -#define __HAL_RCC_USB_OTG_HS_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_OTGHSEN)) != RESET) -#define __HAL_RCC_USB_OTG_HS_ULPI_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_OTGHSULPIEN)) != RESET) -#define __HAL_RCC_BKPSRAM_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_BKPSRAMEN)) != RESET) -#define __HAL_RCC_CCMDATARAMEN_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CCMDATARAMEN))!= RESET) -#define __HAL_RCC_CRC_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CRCEN)) != RESET) - -#define __HAL_RCC_GPIOD_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIODEN)) == RESET) -#define __HAL_RCC_GPIOE_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOEEN)) == RESET) -#define __HAL_RCC_GPIOF_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOFEN)) == RESET) -#define __HAL_RCC_GPIOG_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOGEN)) == RESET) -#define __HAL_RCC_USB_OTG_HS_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_OTGHSEN)) == RESET) -#define __HAL_RCC_USB_OTG_HS_ULPI_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_OTGHSULPIEN)) == RESET) -#define __HAL_RCC_BKPSRAM_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_BKPSRAMEN)) == RESET) -#define __HAL_RCC_CCMDATARAMEN_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CCMDATARAMEN)) == RESET) -#define __HAL_RCC_CRC_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CRCEN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable - * @brief Enable or disable the AHB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_DCMI_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_DCMIEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_DCMIEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_DCMI_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_DCMIEN)) -#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\ - __HAL_RCC_SYSCFG_CLK_ENABLE();\ - }while(0) - -#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN)) - -#define __HAL_RCC_RNG_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_RNG_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_RNGEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Peripheral_Clock_Enable_Disable_Status AHB2 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_DCMI_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_DCMIEN)) != RESET) -#define __HAL_RCC_DCMI_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_DCMIEN)) == RESET) - -#define __HAL_RCC_USB_OTG_FS_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_OTGFSEN)) != RESET) -#define __HAL_RCC_USB_OTG_FS_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_OTGFSEN)) == RESET) - -#define __HAL_RCC_RNG_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_RNGEN)) != RESET) -#define __HAL_RCC_RNG_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_RNGEN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_Clock_Enable_Disable AHB3 Peripheral Clock Enable Disable - * @brief Enables or disables the AHB3 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_FMC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_QSPI_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN);\ - UNUSED(tmpreg); \ - } while(0) - -#define __HAL_RCC_FMC_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_FMCEN)) -#define __HAL_RCC_QSPI_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_QSPIEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_Peripheral_Clock_Enable_Disable_Status AHB3 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB3 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_FMC_IS_CLK_ENABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_FMCEN)) != RESET) -#define __HAL_RCC_QSPI_IS_CLK_ENABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_QSPIEN)) != RESET) - -#define __HAL_RCC_FMC_IS_CLK_DISABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_FMCEN)) == RESET) -#define __HAL_RCC_QSPI_IS_CLK_DISABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_QSPIEN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable - * @brief Enable or disable the Low Speed APB (APB1) peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM6_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM7_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM7EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM7EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM12_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM12EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM12EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM13_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM13EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM13EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM14_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPDIFRX_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPDIFRXEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPDIFRXEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_USART3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_USART3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_USART3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_UART4_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_UART4EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_UART4EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_UART5_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_UART5EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_UART5EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_FMPI2C1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_FMPI2C1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_FMPI2C1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CAN1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CAN2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CEC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_CECEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_CECEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_DAC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM4_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_I2C3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN)) -#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN)) -#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN)) -#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN)) -#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN)) -#define __HAL_RCC_TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN)) -#define __HAL_RCC_TIM7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM7EN)) -#define __HAL_RCC_TIM12_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM12EN)) -#define __HAL_RCC_TIM13_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM13EN)) -#define __HAL_RCC_TIM14_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM14EN)) -#define __HAL_RCC_SPDIFRX_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPDIFRXEN)) -#define __HAL_RCC_USART3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_USART3EN)) -#define __HAL_RCC_UART4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART4EN)) -#define __HAL_RCC_UART5_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART5EN)) -#define __HAL_RCC_FMPI2C1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_FMPI2C1EN)) -#define __HAL_RCC_CAN1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN1EN)) -#define __HAL_RCC_CAN2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN2EN)) -#define __HAL_RCC_CEC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CECEN)) -#define __HAL_RCC_DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Peripheral_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) != RESET) -#define __HAL_RCC_TIM3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) != RESET) -#define __HAL_RCC_TIM4_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM4EN)) != RESET) -#define __HAL_RCC_SPI3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) != RESET) -#define __HAL_RCC_I2C3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C3EN)) != RESET) -#define __HAL_RCC_TIM6_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM6EN)) != RESET) -#define __HAL_RCC_TIM7_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM7EN)) != RESET) -#define __HAL_RCC_TIM12_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM12EN)) != RESET) -#define __HAL_RCC_TIM13_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM13EN)) != RESET) -#define __HAL_RCC_TIM14_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM14EN)) != RESET) -#define __HAL_RCC_SPDIFRX_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPDIFRXEN)) != RESET) -#define __HAL_RCC_USART3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART3EN)) != RESET) -#define __HAL_RCC_UART4_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART4EN)) != RESET) -#define __HAL_RCC_UART5_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART5EN)) != RESET) -#define __HAL_RCC_FMPI2C1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_FMPI2C1EN)) != RESET) -#define __HAL_RCC_CAN1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN1EN)) != RESET) -#define __HAL_RCC_CAN2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN2EN)) != RESET) -#define __HAL_RCC_CEC_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CECEN)) != RESET) -#define __HAL_RCC_DAC_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_DACEN)) != RESET) - -#define __HAL_RCC_TIM2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) == RESET) -#define __HAL_RCC_TIM3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) == RESET) -#define __HAL_RCC_TIM4_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM4EN)) == RESET) -#define __HAL_RCC_SPI3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) == RESET) -#define __HAL_RCC_I2C3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C3EN)) == RESET) -#define __HAL_RCC_TIM6_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM6EN)) == RESET) -#define __HAL_RCC_TIM7_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM7EN)) == RESET) -#define __HAL_RCC_TIM12_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM12EN)) == RESET) -#define __HAL_RCC_TIM13_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM13EN)) == RESET) -#define __HAL_RCC_TIM14_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM14EN)) == RESET) -#define __HAL_RCC_SPDIFRX_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPDIFRXEN)) == RESET) -#define __HAL_RCC_USART3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART3EN)) == RESET) -#define __HAL_RCC_UART4_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART4EN)) == RESET) -#define __HAL_RCC_UART5_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_UART5EN)) == RESET) -#define __HAL_RCC_FMPI2C1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_FMPI2C1EN)) == RESET) -#define __HAL_RCC_CAN1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN1EN)) == RESET) -#define __HAL_RCC_CAN2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN2EN)) == RESET) -#define __HAL_RCC_CEC_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CECEN)) == RESET) -#define __HAL_RCC_DAC_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_DACEN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable - * @brief Enable or disable the High Speed APB (APB2) peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM8_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_ADC2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_ADC3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SAI1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SAI2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SDIO_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI4_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM10_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN)) -#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN)) -#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN)) -#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN)) -#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN)) -#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN)) -#define __HAL_RCC_SAI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI1EN)) -#define __HAL_RCC_SAI2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI2EN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Peripheral_Clock_Enable_Disable_Status APB2 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_SDIO_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SDIOEN)) != RESET) -#define __HAL_RCC_SPI4_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI4EN)) != RESET) -#define __HAL_RCC_TIM10_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM10EN)) != RESET) -#define __HAL_RCC_TIM8_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM8EN)) != RESET) -#define __HAL_RCC_ADC2_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC2EN)) != RESET) -#define __HAL_RCC_ADC3_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC3EN)) != RESET) -#define __HAL_RCC_SAI1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SAI1EN)) != RESET) -#define __HAL_RCC_SAI2_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SAI2EN)) != RESET) - -#define __HAL_RCC_SDIO_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SDIOEN)) == RESET) -#define __HAL_RCC_SPI4_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI4EN)) == RESET) -#define __HAL_RCC_TIM10_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM10EN)) == RESET) -#define __HAL_RCC_TIM8_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM8EN)) == RESET) -#define __HAL_RCC_ADC2_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC2EN)) == RESET) -#define __HAL_RCC_ADC3_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC3EN)) == RESET) -#define __HAL_RCC_SAI1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SAI1EN)) == RESET) -#define __HAL_RCC_SAI2_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SAI2EN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset - * @brief Force or release AHB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST)) -#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST)) -#define __HAL_RCC_GPIOF_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOFRST)) -#define __HAL_RCC_GPIOG_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOGRST)) -#define __HAL_RCC_USB_OTG_HS_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_OTGHRST)) -#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST)) - -#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST)) -#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST)) -#define __HAL_RCC_GPIOF_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOFRST)) -#define __HAL_RCC_GPIOG_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOGRST)) -#define __HAL_RCC_USB_OTG_HS_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_OTGHRST)) -#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset - * @brief Force or release AHB2 peripheral reset. - * @{ - */ -#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST)) -#define __HAL_RCC_RNG_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_RNGRST)) -#define __HAL_RCC_DCMI_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_DCMIRST)) - -#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00U) -#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST)) -#define __HAL_RCC_RNG_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_RNGRST)) -#define __HAL_RCC_DCMI_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_DCMIRST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset - * @brief Force or release AHB3 peripheral reset. - * @{ - */ -#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00U) - -#define __HAL_RCC_FMC_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_FMCRST)) -#define __HAL_RCC_QSPI_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_QSPIRST)) - -#define __HAL_RCC_FMC_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_FMCRST)) -#define __HAL_RCC_QSPI_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_QSPIRST)) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset - * @brief Force or release APB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST)) -#define __HAL_RCC_TIM7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM7RST)) -#define __HAL_RCC_TIM12_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM12RST)) -#define __HAL_RCC_TIM13_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM13RST)) -#define __HAL_RCC_TIM14_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM14RST)) -#define __HAL_RCC_SPDIFRX_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPDIFRXRST)) -#define __HAL_RCC_USART3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USART3RST)) -#define __HAL_RCC_UART4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART4RST)) -#define __HAL_RCC_UART5_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART5RST)) -#define __HAL_RCC_FMPI2C1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_FMPI2C1RST)) -#define __HAL_RCC_CAN1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN1RST)) -#define __HAL_RCC_CAN2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN2RST)) -#define __HAL_RCC_CEC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CECRST)) -#define __HAL_RCC_DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST)) -#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST)) -#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST)) -#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST)) -#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST)) -#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST)) - -#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST)) -#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST)) -#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST)) -#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST)) -#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST)) -#define __HAL_RCC_TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST)) -#define __HAL_RCC_TIM7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM7RST)) -#define __HAL_RCC_TIM12_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM12RST)) -#define __HAL_RCC_TIM13_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM13RST)) -#define __HAL_RCC_TIM14_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM14RST)) -#define __HAL_RCC_SPDIFRX_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPDIFRXRST)) -#define __HAL_RCC_USART3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_USART3RST)) -#define __HAL_RCC_UART4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART4RST)) -#define __HAL_RCC_UART5_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART5RST)) -#define __HAL_RCC_FMPI2C1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_FMPI2C1RST)) -#define __HAL_RCC_CAN1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN1RST)) -#define __HAL_RCC_CAN2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN2RST)) -#define __HAL_RCC_CEC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CECRST)) -#define __HAL_RCC_DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset - * @brief Force or release APB2 peripheral reset. - * @{ - */ -#define __HAL_RCC_TIM8_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM8RST)) -#define __HAL_RCC_SAI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SAI1RST)) -#define __HAL_RCC_SAI2_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SAI2RST)) -#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST)) -#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST)) -#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST)) - -#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST)) -#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST)) -#define __HAL_RCC_TIM10_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST)) -#define __HAL_RCC_TIM8_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM8RST)) -#define __HAL_RCC_SAI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SAI1RST)) -#define __HAL_RCC_SAI2_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SAI2RST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN)) -#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN)) -#define __HAL_RCC_GPIOF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOFLPEN)) -#define __HAL_RCC_GPIOG_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOGLPEN)) -#define __HAL_RCC_SRAM2_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM2LPEN)) -#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSLPEN)) -#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSULPILPEN)) -#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN)) -#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN)) -#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN)) -#define __HAL_RCC_BKPSRAM_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_BKPSRAMLPEN)) - -#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN)) -#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN)) -#define __HAL_RCC_GPIOF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOFLPEN)) -#define __HAL_RCC_GPIOG_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOGLPEN)) -#define __HAL_RCC_SRAM2_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM2LPEN)) -#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSLPEN)) -#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSULPILPEN)) -#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN)) -#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN)) -#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN)) -#define __HAL_RCC_BKPSRAM_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_BKPSRAMLPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN)) -#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN)) - -#define __HAL_RCC_RNG_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_RNGLPEN)) -#define __HAL_RCC_RNG_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_RNGLPEN)) - -#define __HAL_RCC_DCMI_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_DCMILPEN)) -#define __HAL_RCC_DCMI_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_DCMILPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_LowPower_Enable_Disable AHB3 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_FMC_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_FMCLPEN)) -#define __HAL_RCC_QSPI_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_QSPILPEN)) - -#define __HAL_RCC_FMC_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_FMCLPEN)) -#define __HAL_RCC_QSPI_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_QSPILPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_TIM6_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM6LPEN)) -#define __HAL_RCC_TIM7_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM7LPEN)) -#define __HAL_RCC_TIM12_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM12LPEN)) -#define __HAL_RCC_TIM13_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM13LPEN)) -#define __HAL_RCC_TIM14_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM14LPEN)) -#define __HAL_RCC_SPDIFRX_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPDIFRXLPEN)) -#define __HAL_RCC_USART3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_USART3LPEN)) -#define __HAL_RCC_UART4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART4LPEN)) -#define __HAL_RCC_UART5_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART5LPEN)) -#define __HAL_RCC_FMPI2C1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_FMPI2C1LPEN)) -#define __HAL_RCC_CAN1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN1LPEN)) -#define __HAL_RCC_CAN2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN2LPEN)) -#define __HAL_RCC_CEC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CECLPEN)) -#define __HAL_RCC_DAC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_DACLPEN)) -#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN)) -#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN)) -#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN)) -#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN)) -#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN)) - -#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN)) -#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN)) -#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN)) -#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN)) -#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN)) -#define __HAL_RCC_TIM6_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM6LPEN)) -#define __HAL_RCC_TIM7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM7LPEN)) -#define __HAL_RCC_TIM12_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM12LPEN)) -#define __HAL_RCC_TIM13_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM13LPEN)) -#define __HAL_RCC_TIM14_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM14LPEN)) -#define __HAL_RCC_SPDIFRX_CLK_SLEEP_DISABLE()(RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPDIFRXLPEN)) -#define __HAL_RCC_USART3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_USART3LPEN)) -#define __HAL_RCC_UART4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART4LPEN)) -#define __HAL_RCC_UART5_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART5LPEN)) -#define __HAL_RCC_FMPI2C1_CLK_SLEEP_DISABLE()(RCC->APB1LPENR &= ~(RCC_APB1LPENR_FMPI2C1LPEN)) -#define __HAL_RCC_CAN1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN1LPEN)) -#define __HAL_RCC_CAN2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN2LPEN)) -#define __HAL_RCC_CEC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CECLPEN)) -#define __HAL_RCC_DAC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_DACLPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_TIM8_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM8LPEN)) -#define __HAL_RCC_ADC2_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC2LPEN)) -#define __HAL_RCC_ADC3_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC3LPEN)) -#define __HAL_RCC_SAI1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SAI1LPEN)) -#define __HAL_RCC_SAI2_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SAI2LPEN)) -#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN)) -#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN)) -#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE()(RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN)) - -#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN)) -#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN)) -#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE()(RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN)) -#define __HAL_RCC_TIM8_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM8LPEN)) -#define __HAL_RCC_ADC2_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC2LPEN)) -#define __HAL_RCC_ADC3_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC3LPEN)) -#define __HAL_RCC_SAI1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SAI1LPEN)) -#define __HAL_RCC_SAI2_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SAI2LPEN)) -/** - * @} - */ - -#endif /* STM32F446xx */ -/*----------------------------------------------------------------------------*/ - -/*----------STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx----------*/ -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable - * @brief Enables or disables the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_CRC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOF_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOFEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOFEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_GPIOG_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOGEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOGEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CRC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\ - UNUSED(tmpreg); \ - } while(0) - -#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN)) -#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN)) -#define __HAL_RCC_GPIOF_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOFEN)) -#define __HAL_RCC_GPIOG_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOGEN)) -#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_Peripheral_Clock_Enable_Disable_Status AHB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_GPIOD_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIODEN)) != RESET) -#define __HAL_RCC_GPIOE_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOEEN)) != RESET) -#define __HAL_RCC_GPIOF_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOFEN)) != RESET) -#define __HAL_RCC_GPIOG_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOGEN)) != RESET) -#define __HAL_RCC_CRC_IS_CLK_ENABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CRCEN)) != RESET) - -#define __HAL_RCC_GPIOD_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIODEN)) == RESET) -#define __HAL_RCC_GPIOE_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOEEN)) == RESET) -#define __HAL_RCC_GPIOF_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOFEN)) == RESET) -#define __HAL_RCC_GPIOG_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_GPIOGEN)) == RESET) -#define __HAL_RCC_CRC_IS_CLK_DISABLED() ((RCC->AHB1ENR & (RCC_AHB1ENR_CRCEN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable - * @brief Enable or disable the AHB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\ - __HAL_RCC_SYSCFG_CLK_ENABLE();\ - }while(0) - -#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN)) - -#define __HAL_RCC_RNG_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_RNG_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_RNGEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Peripheral_Clock_Enable_Disable_Status AHB2 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_USB_OTG_FS_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_OTGFSEN)) != RESET) -#define __HAL_RCC_USB_OTG_FS_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_OTGFSEN)) == RESET) - -#define __HAL_RCC_RNG_IS_CLK_ENABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_RNGEN)) != RESET) -#define __HAL_RCC_RNG_IS_CLK_DISABLED() ((RCC->AHB2ENR & (RCC_AHB2ENR_RNGEN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_Clock_Enable_Disable AHB3 Peripheral Clock Enable Disable - * @brief Enables or disables the AHB3 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#if defined(STM32F412Zx) || defined(STM32F412Vx) -#define __HAL_RCC_FSMC_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_QSPI_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN);\ - UNUSED(tmpreg); \ - } while(0) - -#define __HAL_RCC_FSMC_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_FSMCEN)) -#define __HAL_RCC_QSPI_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_QSPIEN)) -#endif /* STM32F412Zx || STM32F412Vx */ -#if defined(STM32F412Rx) -#define __HAL_RCC_QSPI_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN);\ - UNUSED(tmpreg); \ - } while(0) - -#define __HAL_RCC_QSPI_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_QSPIEN)) -#endif /* STM32F412Rx */ -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_Peripheral_Clock_Enable_Disable_Status AHB3 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the AHB3 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#if defined(STM32F412Zx) || defined(STM32F412Vx) -#define __HAL_RCC_FSMC_IS_CLK_ENABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_FSMCEN)) != RESET) -#define __HAL_RCC_QSPI_IS_CLK_ENABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_QSPIEN)) != RESET) - -#define __HAL_RCC_FSMC_IS_CLK_DISABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_FSMCEN)) == RESET) -#define __HAL_RCC_QSPI_IS_CLK_DISABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_QSPIEN)) == RESET) -#endif /* STM32F412Zx || STM32F412Vx */ -#if defined(STM32F412Rx) -#define __HAL_RCC_QSPI_IS_CLK_ENABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_QSPIEN)) != RESET) -#define __HAL_RCC_QSPI_IS_CLK_DISABLED() ((RCC->AHB3ENR & (RCC_AHB3ENR_QSPIEN)) == RESET) -#endif /* STM32F412Rx */ -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable - * @brief Enable or disable the Low Speed APB (APB1) peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM6_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM7_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM7EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM7EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM12_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM12EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM12EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM13_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM13EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM13EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM14_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_RTCAPB_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_RTCAPBEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_RTCAPBEN);\ - UNUSED(tmpreg); \ - } while(0) -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) -#define __HAL_RCC_USART3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_USART3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_USART3EN);\ - UNUSED(tmpreg); \ - } while(0) -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx */ -#define __HAL_RCC_FMPI2C1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_FMPI2C1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_FMPI2C1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CAN1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_CAN2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_CAN2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM2_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM4_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_I2C3_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN)) -#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN)) -#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN)) -#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN)) -#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN)) -#define __HAL_RCC_TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN)) -#define __HAL_RCC_TIM7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM7EN)) -#define __HAL_RCC_TIM12_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM12EN)) -#define __HAL_RCC_TIM13_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM13EN)) -#define __HAL_RCC_TIM14_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM14EN)) -#define __HAL_RCC_RTCAPB_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_RTCAPBEN)) -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) -#define __HAL_RCC_USART3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_USART3EN)) -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx */ -#define __HAL_RCC_FMPI2C1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_FMPI2C1EN)) -#define __HAL_RCC_CAN1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN1EN)) -#define __HAL_RCC_CAN2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN2EN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Peripheral_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB1 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) != RESET) -#define __HAL_RCC_TIM3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) != RESET) -#define __HAL_RCC_TIM4_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM4EN)) != RESET) -#define __HAL_RCC_SPI3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) != RESET) -#define __HAL_RCC_I2C3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C3EN)) != RESET) -#define __HAL_RCC_TIM6_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM6EN)) != RESET) -#define __HAL_RCC_TIM7_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM7EN)) != RESET) -#define __HAL_RCC_TIM12_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM12EN)) != RESET) -#define __HAL_RCC_TIM13_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM13EN)) != RESET) -#define __HAL_RCC_TIM14_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM14EN)) != RESET) -#define __HAL_RCC_RTCAPB_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_RTCAPBEN)) != RESET) -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) -#define __HAL_RCC_USART3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART3EN)) != RESET) -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx */ -#define __HAL_RCC_FMPI2C1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_FMPI2C1EN)) != RESET) -#define __HAL_RCC_CAN1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN1EN))!= RESET) -#define __HAL_RCC_CAN2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN2EN)) != RESET) - -#define __HAL_RCC_TIM2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) == RESET) -#define __HAL_RCC_TIM3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) == RESET) -#define __HAL_RCC_TIM4_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM4EN)) == RESET) -#define __HAL_RCC_SPI3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI3EN)) == RESET) -#define __HAL_RCC_I2C3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C3EN)) == RESET) -#define __HAL_RCC_TIM6_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM6EN)) == RESET) -#define __HAL_RCC_TIM7_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM7EN)) == RESET) -#define __HAL_RCC_TIM12_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM12EN)) == RESET) -#define __HAL_RCC_TIM13_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM13EN)) == RESET) -#define __HAL_RCC_TIM14_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM14EN)) == RESET) -#define __HAL_RCC_RTCAPB_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_RTCAPBEN)) == RESET) -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) -#define __HAL_RCC_USART3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART3EN)) == RESET) -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx */ -#define __HAL_RCC_FMPI2C1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_FMPI2C1EN)) == RESET) -#define __HAL_RCC_CAN1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN1EN)) == RESET) -#define __HAL_RCC_CAN2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_CAN2EN)) == RESET) -/** - * @} - */ -/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable - * @brief Enable or disable the High Speed APB (APB2) peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_TIM8_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI5_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI5EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI5EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_EXTIT_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_EXTITEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_EXTITEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_DFSDM1_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_DFSDM1EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_DFSDM1EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SDIO_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SPI4_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_TIM10_CLK_ENABLE() do { \ - __IO uint32_t tmpreg = 0x00U; \ - SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\ - /* Delay after an RCC peripheral clock enabling */ \ - tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\ - UNUSED(tmpreg); \ - } while(0) -#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN)) -#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN)) -#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN)) -#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN)) -#define __HAL_RCC_SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN)) -#define __HAL_RCC_EXTIT_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_EXTITEN)) -#define __HAL_RCC_DFSDM1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_DFSDM1EN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Peripheral_Clock_Enable_Disable_Status APB2 Peripheral Clock Enable Disable Status - * @brief Get the enable or disable status of the APB2 peripheral clock. - * @note After reset, the peripheral clock (used for registers read/write access) - * is disabled and the application software has to enable this clock before - * using it. - * @{ - */ -#define __HAL_RCC_SDIO_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SDIOEN)) != RESET) -#define __HAL_RCC_SPI4_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI4EN)) != RESET) -#define __HAL_RCC_TIM10_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM10EN)) != RESET) -#define __HAL_RCC_TIM8_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM8EN)) != RESET) -#define __HAL_RCC_SPI5_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI5EN)) != RESET) -#define __HAL_RCC_EXTIT_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_EXTITEN)) != RESET) -#define __HAL_RCC_DFSDM1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_DFSDM1EN)) != RESET) - -#define __HAL_RCC_SDIO_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SDIOEN)) == RESET) -#define __HAL_RCC_SPI4_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI4EN)) == RESET) -#define __HAL_RCC_TIM10_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM10EN)) == RESET) -#define __HAL_RCC_TIM8_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM8EN)) == RESET) -#define __HAL_RCC_SPI5_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI5EN)) == RESET) -#define __HAL_RCC_EXTIT_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_EXTITEN)) == RESET) -#define __HAL_RCC_DFSDM1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_DFSDM1EN)) == RESET) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset - * @brief Force or release AHB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST)) -#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST)) -#define __HAL_RCC_GPIOF_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOFRST)) -#define __HAL_RCC_GPIOG_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOGRST)) -#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST)) - -#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST)) -#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST)) -#define __HAL_RCC_GPIOF_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOFRST)) -#define __HAL_RCC_GPIOG_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOGRST)) -#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset - * @brief Force or release AHB2 peripheral reset. - * @{ - */ -#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00U) - -#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST)) -#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST)) - -#define __HAL_RCC_RNG_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_RNGRST)) -#define __HAL_RCC_RNG_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_RNGRST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset - * @brief Force or release AHB3 peripheral reset. - * @{ - */ -#if defined(STM32F412Zx) || defined(STM32F412Vx) -#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00U) - -#define __HAL_RCC_FSMC_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_FSMCRST)) -#define __HAL_RCC_QSPI_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_QSPIRST)) - -#define __HAL_RCC_FSMC_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_FSMCRST)) -#define __HAL_RCC_QSPI_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_QSPIRST)) -#endif /* STM32F412Zx || STM32F412Vx */ -#if defined(STM32F412Cx) -#define __HAL_RCC_AHB3_FORCE_RESET() -#define __HAL_RCC_AHB3_RELEASE_RESET() - -#define __HAL_RCC_FSMC_FORCE_RESET() -#define __HAL_RCC_QSPI_FORCE_RESET() - -#define __HAL_RCC_FSMC_RELEASE_RESET() -#define __HAL_RCC_QSPI_RELEASE_RESET() -#endif /* STM32F412Cx */ -#if defined(STM32F412Rx) -#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFFU) -#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00U) - -#define __HAL_RCC_FSMC_FORCE_RESET() -#define __HAL_RCC_QSPI_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_QSPIRST)) - -#define __HAL_RCC_FSMC_RELEASE_RESET() -#define __HAL_RCC_QSPI_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_QSPIRST)) -#endif /* STM32F412Rx */ -/** - * @} - */ - -/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset - * @brief Force or release APB1 peripheral reset. - * @{ - */ -#define __HAL_RCC_TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST)) -#define __HAL_RCC_TIM7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM7RST)) -#define __HAL_RCC_TIM12_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM12RST)) -#define __HAL_RCC_TIM13_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM13RST)) -#define __HAL_RCC_TIM14_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM14RST)) -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) -#define __HAL_RCC_USART3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USART3RST)) -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx */ -#define __HAL_RCC_FMPI2C1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_FMPI2C1RST)) -#define __HAL_RCC_CAN1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN1RST)) -#define __HAL_RCC_CAN2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN2RST)) -#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST)) -#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST)) -#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST)) -#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST)) -#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST)) - -#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST)) -#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST)) -#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST)) -#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST)) -#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST)) -#define __HAL_RCC_TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST)) -#define __HAL_RCC_TIM7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM7RST)) -#define __HAL_RCC_TIM12_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM12RST)) -#define __HAL_RCC_TIM13_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM13RST)) -#define __HAL_RCC_TIM14_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM14RST)) -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) -#define __HAL_RCC_USART3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_USART3RST)) -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx */ -#define __HAL_RCC_FMPI2C1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_FMPI2C1RST)) -#define __HAL_RCC_CAN1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN1RST)) -#define __HAL_RCC_CAN2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN2RST)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset - * @brief Force or release APB2 peripheral reset. - * @{ - */ -#define __HAL_RCC_TIM8_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM8RST)) -#define __HAL_RCC_SPI5_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI5RST)) -#define __HAL_RCC_DFSDM1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_DFSDM1RST)) -#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST)) -#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST)) -#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST)) - -#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST)) -#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST)) -#define __HAL_RCC_TIM10_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST)) -#define __HAL_RCC_TIM8_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM8RST)) -#define __HAL_RCC_SPI5_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI5RST)) -#define __HAL_RCC_DFSDM1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_DFSDM1RST)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN)) -#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN)) -#define __HAL_RCC_GPIOF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOFLPEN)) -#define __HAL_RCC_GPIOG_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOGLPEN)) -#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN)) -#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN)) -#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN)) - -#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN)) -#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN)) -#define __HAL_RCC_GPIOF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOFLPEN)) -#define __HAL_RCC_GPIOG_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOGLPEN)) -#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN)) -#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN)) -#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN)) - -#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN)) - -#define __HAL_RCC_RNG_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_RNGLPEN)) -#define __HAL_RCC_RNG_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_RNGLPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_AHB3_LowPower_Enable_Disable AHB3 Peripheral Low Power Enable Disable - * @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#if defined(STM32F412Zx) || defined(STM32F412Vx) -#define __HAL_RCC_FSMC_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_FSMCLPEN)) -#define __HAL_RCC_QSPI_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_QSPILPEN)) - -#define __HAL_RCC_FSMC_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_FSMCLPEN)) -#define __HAL_RCC_QSPI_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_QSPILPEN)) -#endif /* STM32F412Zx || STM32F412Vx */ - -#if defined(STM32F412Rx) -#define __HAL_RCC_QSPI_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_QSPILPEN)) -#define __HAL_RCC_QSPI_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_QSPILPEN)) -#endif /* STM32F412Rx */ -/** - * @} - */ - -/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_TIM6_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM6LPEN)) -#define __HAL_RCC_TIM7_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM7LPEN)) -#define __HAL_RCC_TIM12_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM12LPEN)) -#define __HAL_RCC_TIM13_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM13LPEN)) -#define __HAL_RCC_TIM14_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM14LPEN)) -#define __HAL_RCC_RTCAPB_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_RTCAPBLPEN)) -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) -#define __HAL_RCC_USART3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_USART3LPEN)) -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx */ -#define __HAL_RCC_FMPI2C1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_FMPI2C1LPEN)) -#define __HAL_RCC_CAN1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN1LPEN)) -#define __HAL_RCC_CAN2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN2LPEN)) -#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN)) -#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN)) -#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN)) -#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN)) -#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN)) - -#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN)) -#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN)) -#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN)) -#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN)) -#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN)) -#define __HAL_RCC_TIM6_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM6LPEN)) -#define __HAL_RCC_TIM7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM7LPEN)) -#define __HAL_RCC_TIM12_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM12LPEN)) -#define __HAL_RCC_TIM13_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM13LPEN)) -#define __HAL_RCC_TIM14_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM14LPEN)) -#define __HAL_RCC_RTCAPB_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_RTCAPBLPEN)) -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) -#define __HAL_RCC_USART3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_USART3LPEN)) -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx */ -#define __HAL_RCC_FMPI2C1_CLK_SLEEP_DISABLE()(RCC->APB1LPENR &= ~(RCC_APB1LPENR_FMPI2C1LPEN)) -#define __HAL_RCC_CAN1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN1LPEN)) -#define __HAL_RCC_CAN2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN2LPEN)) -/** - * @} - */ - -/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable - * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode. - * @note Peripheral clock gating in SLEEP mode can be used to further reduce - * power consumption. - * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. - * @note By default, all peripheral clocks are enabled during SLEEP mode. - * @{ - */ -#define __HAL_RCC_TIM8_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM8LPEN)) -#define __HAL_RCC_SPI5_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI5LPEN)) -#define __HAL_RCC_EXTIT_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_EXTITLPEN)) -#define __HAL_RCC_DFSDM1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_DFSDM1LPEN)) -#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN)) -#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN)) -#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN)) - -#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN)) -#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN)) -#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN)) -#define __HAL_RCC_TIM8_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM8LPEN)) -#define __HAL_RCC_SPI5_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI5LPEN)) -#define __HAL_RCC_EXTIT_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_EXTITLPEN)) -#define __HAL_RCC_DFSDM1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_DFSDM1LPEN)) -/** - * @} - */ -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ -/*----------------------------------------------------------------------------*/ - -/*------------------------------- PLL Configuration --------------------------*/ -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F446xx) ||\ - defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ - defined(STM32F412Rx) || defined(STM32F412Cx) -/** @brief Macro to configure the main PLL clock source, multiplication and division factors. - * @note This function must be used only when the main PLL is disabled. - * @param __RCC_PLLSource__: specifies the PLL entry clock source. - * This parameter can be one of the following values: - * @arg RCC_PLLSOURCE_HSI: HSI oscillator clock selected as PLL clock entry - * @arg RCC_PLLSOURCE_HSE: HSE oscillator clock selected as PLL clock entry - * @note This clock source (RCC_PLLSource) is common for the main PLL and PLLI2S. - * @param __PLLM__: specifies the division factor for PLL VCO input clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 63. - * @note You have to set the PLLM parameter correctly to ensure that the VCO input - * frequency ranges from 1 to 2 MHz. It is recommended to select a frequency - * of 2 MHz to limit PLL jitter. - * @param __PLLN__: specifies the multiplication factor for PLL VCO output clock - * This parameter must be a number between Min_Data = 50 and Max_Data = 432. - * @note You have to set the PLLN parameter correctly to ensure that the VCO - * output frequency is between 100 and 432 MHz. - * - * @param __PLLP__: specifies the division factor for main system clock (SYSCLK) - * This parameter must be a number in the range {2, 4, 6, or 8}. - * - * @param __PLLQ__: specifies the division factor for OTG FS, SDIO and RNG clocks - * This parameter must be a number between Min_Data = 2 and Max_Data = 15. - * @note If the USB OTG FS is used in your application, you have to set the - * PLLQ parameter correctly to have 48 MHz clock for the USB. However, - * the SDIO and RNG need a frequency lower than or equal to 48 MHz to work - * correctly. - * - * @param __PLLR__: PLL division factor for I2S, SAI, SYSTEM, SPDIFRX clocks. - * This parameter must be a number between Min_Data = 2 and Max_Data = 7. - * @note This parameter is only available in STM32F446xx/STM32F469xx/STM32F479xx/ - STM32F412Zx/STM32F412Vx/STM32F412Rx/STM32F412Cx devices. - * - */ -#define __HAL_RCC_PLL_CONFIG(__RCC_PLLSource__, __PLLM__, __PLLN__, __PLLP__, __PLLQ__,__PLLR__) \ - (RCC->PLLCFGR = ((__RCC_PLLSource__) | (__PLLM__) | \ - ((__PLLN__) << POSITION_VAL(RCC_PLLCFGR_PLLN)) | \ - ((((__PLLP__) >> 1) -1) << POSITION_VAL(RCC_PLLCFGR_PLLP)) | \ - ((__PLLQ__) << POSITION_VAL(RCC_PLLCFGR_PLLQ)) | \ - ((__PLLR__) << POSITION_VAL(RCC_PLLCFGR_PLLR)))) -#else -/** @brief Macro to configure the main PLL clock source, multiplication and division factors. - * @note This function must be used only when the main PLL is disabled. - * @param __RCC_PLLSource__: specifies the PLL entry clock source. - * This parameter can be one of the following values: - * @arg RCC_PLLSOURCE_HSI: HSI oscillator clock selected as PLL clock entry - * @arg RCC_PLLSOURCE_HSE: HSE oscillator clock selected as PLL clock entry - * @note This clock source (RCC_PLLSource) is common for the main PLL and PLLI2S. - * @param __PLLM__: specifies the division factor for PLL VCO input clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 63. - * @note You have to set the PLLM parameter correctly to ensure that the VCO input - * frequency ranges from 1 to 2 MHz. It is recommended to select a frequency - * of 2 MHz to limit PLL jitter. - * @param __PLLN__: specifies the multiplication factor for PLL VCO output clock - * This parameter must be a number between Min_Data = 50 and Max_Data = 432 - * Except for STM32F411xE devices where Min_Data = 192. - * @note You have to set the PLLN parameter correctly to ensure that the VCO - * output frequency is between 100 and 432 MHz, Except for STM32F411xE devices - * where frequency is between 192 and 432 MHz. - * @param __PLLP__: specifies the division factor for main system clock (SYSCLK) - * This parameter must be a number in the range {2, 4, 6, or 8}. - * - * @param __PLLQ__: specifies the division factor for OTG FS, SDIO and RNG clocks - * This parameter must be a number between Min_Data = 2 and Max_Data = 15. - * @note If the USB OTG FS is used in your application, you have to set the - * PLLQ parameter correctly to have 48 MHz clock for the USB. However, - * the SDIO and RNG need a frequency lower than or equal to 48 MHz to work - * correctly. - * - */ -#define __HAL_RCC_PLL_CONFIG(__RCC_PLLSource__, __PLLM__, __PLLN__, __PLLP__, __PLLQ__) \ - (RCC->PLLCFGR = (0x20000000U | (__RCC_PLLSource__) | (__PLLM__)| \ - ((__PLLN__) << POSITION_VAL(RCC_PLLCFGR_PLLN)) | \ - ((((__PLLP__) >> 1) -1) << POSITION_VAL(RCC_PLLCFGR_PLLP)) | \ - ((__PLLQ__) << POSITION_VAL(RCC_PLLCFGR_PLLQ)))) -#endif /* STM32F410xx || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ -/*----------------------------------------------------------------------------*/ - -/*----------------------------PLLI2S Configuration ---------------------------*/ -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \ - defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \ - defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ - defined(STM32F412Rx) || defined(STM32F412Cx) - -/** @brief Macros to enable or disable the PLLI2S. - * @note The PLLI2S is disabled by hardware when entering STOP and STANDBY modes. - */ -#define __HAL_RCC_PLLI2S_ENABLE() (*(__IO uint32_t *) RCC_CR_PLLI2SON_BB = ENABLE) -#define __HAL_RCC_PLLI2S_DISABLE() (*(__IO uint32_t *) RCC_CR_PLLI2SON_BB = DISABLE) - -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || - STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || - STM32F412Rx || STM32F412Cx */ -#if defined(STM32F446xx) -/** @brief Macro to configure the PLLI2S clock multiplication and division factors . - * @note This macro must be used only when the PLLI2S is disabled. - * @note PLLI2S clock source is common with the main PLL (configured in - * HAL_RCC_ClockConfig() API). - * @param __PLLI2SM__: specifies the division factor for PLLI2S VCO input clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 63. - * @note You have to set the PLLI2SM parameter correctly to ensure that the VCO input - * frequency ranges from 1 to 2 MHz. It is recommended to select a frequency - * of 1 MHz to limit PLLI2S jitter. - * - * @param __PLLI2SN__: specifies the multiplication factor for PLLI2S VCO output clock - * This parameter must be a number between Min_Data = 50 and Max_Data = 432. - * @note You have to set the PLLI2SN parameter correctly to ensure that the VCO - * output frequency is between Min_Data = 100 and Max_Data = 432 MHz. - * - * @param __PLLI2SP__: specifies division factor for SPDIFRX Clock. - * This parameter must be a number in the range {2, 4, 6, or 8}. - * @note the PLLI2SP parameter is only available with STM32F446xx Devices - * - * @param __PLLI2SR__: specifies the division factor for I2S clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 7. - * @note You have to set the PLLI2SR parameter correctly to not exceed 192 MHz - * on the I2S clock frequency. - * - * @param __PLLI2SQ__: specifies the division factor for SAI clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 15. - */ -#define __HAL_RCC_PLLI2S_CONFIG(__PLLI2SM__, __PLLI2SN__, __PLLI2SP__, __PLLI2SQ__, __PLLI2SR__) \ - (RCC->PLLI2SCFGR = ((__PLLI2SM__) |\ - ((__PLLI2SN__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)) |\ - ((((__PLLI2SP__) >> 1) -1) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SP)) |\ - ((__PLLI2SQ__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SQ)) |\ - ((__PLLI2SR__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)))) -#elif defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -/** @brief Macro to configure the PLLI2S clock multiplication and division factors . - * @note This macro must be used only when the PLLI2S is disabled. - * @note PLLI2S clock source is common with the main PLL (configured in - * HAL_RCC_ClockConfig() API). - * @param __PLLI2SM__: specifies the division factor for PLLI2S VCO input clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 63. - * @note You have to set the PLLI2SM parameter correctly to ensure that the VCO input - * frequency ranges from 1 to 2 MHz. It is recommended to select a frequency - * of 1 MHz to limit PLLI2S jitter. - * - * @param __PLLI2SN__: specifies the multiplication factor for PLLI2S VCO output clock - * This parameter must be a number between Min_Data = 50 and Max_Data = 432. - * @note You have to set the PLLI2SN parameter correctly to ensure that the VCO - * output frequency is between Min_Data = 100 and Max_Data = 432 MHz. - * - * @param __PLLI2SR__: specifies the division factor for I2S clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 7. - * @note You have to set the PLLI2SR parameter correctly to not exceed 192 MHz - * on the I2S clock frequency. - * - * @param __PLLI2SQ__: specifies the division factor for SAI clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 15. - */ -#define __HAL_RCC_PLLI2S_CONFIG(__PLLI2SM__, __PLLI2SN__, __PLLI2SQ__, __PLLI2SR__) \ - (RCC->PLLI2SCFGR = ((__PLLI2SM__) |\ - ((__PLLI2SN__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)) |\ - ((__PLLI2SQ__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SQ)) |\ - ((__PLLI2SR__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)))) -#else -/** @brief Macro to configure the PLLI2S clock multiplication and division factors . - * @note This macro must be used only when the PLLI2S is disabled. - * @note PLLI2S clock source is common with the main PLL (configured in - * HAL_RCC_ClockConfig() API). - * @param __PLLI2SN__: specifies the multiplication factor for PLLI2S VCO output clock - * This parameter must be a number between Min_Data = 50 and Max_Data = 432. - * @note You have to set the PLLI2SN parameter correctly to ensure that the VCO - * output frequency is between Min_Data = 100 and Max_Data = 432 MHz. - * - * @param __PLLI2SR__: specifies the division factor for I2S clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 7. - * @note You have to set the PLLI2SR parameter correctly to not exceed 192 MHz - * on the I2S clock frequency. - * - */ -#define __HAL_RCC_PLLI2S_CONFIG(__PLLI2SN__, __PLLI2SR__) \ - (RCC->PLLI2SCFGR = (((__PLLI2SN__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)) |\ - ((__PLLI2SR__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)))) -#endif /* STM32F446xx */ - -#if defined(STM32F411xE) -/** @brief Macro to configure the PLLI2S clock multiplication and division factors . - * @note This macro must be used only when the PLLI2S is disabled. - * @note This macro must be used only when the PLLI2S is disabled. - * @note PLLI2S clock source is common with the main PLL (configured in - * HAL_RCC_ClockConfig() API). - * @param __PLLI2SM__: specifies the division factor for PLLI2S VCO input clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 63. - * @note The PLLI2SM parameter is only used with STM32F411xE/STM32F410xx Devices - * @note You have to set the PLLI2SM parameter correctly to ensure that the VCO input - * frequency ranges from 1 to 2 MHz. It is recommended to select a frequency - * of 2 MHz to limit PLLI2S jitter. - * @param __PLLI2SN__: specifies the multiplication factor for PLLI2S VCO output clock - * This parameter must be a number between Min_Data = 192 and Max_Data = 432. - * @note You have to set the PLLI2SN parameter correctly to ensure that the VCO - * output frequency is between Min_Data = 192 and Max_Data = 432 MHz. - * @param __PLLI2SR__: specifies the division factor for I2S clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 7. - * @note You have to set the PLLI2SR parameter correctly to not exceed 192 MHz - * on the I2S clock frequency. - */ -#define __HAL_RCC_PLLI2S_I2SCLK_CONFIG(__PLLI2SM__, __PLLI2SN__, __PLLI2SR__) (RCC->PLLI2SCFGR = ((__PLLI2SM__) |\ - ((__PLLI2SN__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)) |\ - ((__PLLI2SR__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)))) -#endif /* STM32F411xE */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) -/** @brief Macro used by the SAI HAL driver to configure the PLLI2S clock multiplication and division factors. - * @note This macro must be used only when the PLLI2S is disabled. - * @note PLLI2S clock source is common with the main PLL (configured in - * HAL_RCC_ClockConfig() API) - * @param __PLLI2SN__: specifies the multiplication factor for PLLI2S VCO output clock. - * This parameter must be a number between Min_Data = 50 and Max_Data = 432. - * @note You have to set the PLLI2SN parameter correctly to ensure that the VCO - * output frequency is between Min_Data = 100 and Max_Data = 432 MHz. - * @param __PLLI2SQ__: specifies the division factor for SAI1 clock. - * This parameter must be a number between Min_Data = 2 and Max_Data = 15. - * @note the PLLI2SQ parameter is only available with STM32F427xx/437xx/429xx/439xx/469xx/479xx - * Devices and can be configured using the __HAL_RCC_PLLI2S_PLLSAICLK_CONFIG() macro - * @param __PLLI2SR__: specifies the division factor for I2S clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 7. - * @note You have to set the PLLI2SR parameter correctly to not exceed 192 MHz - * on the I2S clock frequency. - */ -#define __HAL_RCC_PLLI2S_SAICLK_CONFIG(__PLLI2SN__, __PLLI2SQ__, __PLLI2SR__) (RCC->PLLI2SCFGR = ((__PLLI2SN__) << 6) |\ - ((__PLLI2SQ__) << 24) |\ - ((__PLLI2SR__) << 28)) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ -/*----------------------------------------------------------------------------*/ - -/*------------------------------ PLLSAI Configuration ------------------------*/ -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) -/** @brief Macros to Enable or Disable the PLLISAI. - * @note The PLLSAI is only available with STM32F429x/439x Devices. - * @note The PLLSAI is disabled by hardware when entering STOP and STANDBY modes. - */ -#define __HAL_RCC_PLLSAI_ENABLE() (*(__IO uint32_t *) RCC_CR_PLLSAION_BB = ENABLE) -#define __HAL_RCC_PLLSAI_DISABLE() (*(__IO uint32_t *) RCC_CR_PLLSAION_BB = DISABLE) - -#if defined(STM32F446xx) -/** @brief Macro to configure the PLLSAI clock multiplication and division factors. - * - * @param __PLLSAIM__: specifies the division factor for PLLSAI VCO input clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 63. - * @note You have to set the PLLSAIM parameter correctly to ensure that the VCO input - * frequency ranges from 1 to 2 MHz. It is recommended to select a frequency - * of 1 MHz to limit PLLI2S jitter. - * @note The PLLSAIM parameter is only used with STM32F446xx Devices - * - * @param __PLLSAIN__: specifies the multiplication factor for PLLSAI VCO output clock. - * This parameter must be a number between Min_Data = 50 and Max_Data = 432. - * @note You have to set the PLLSAIN parameter correctly to ensure that the VCO - * output frequency is between Min_Data = 100 and Max_Data = 432 MHz. - * - * @param __PLLSAIP__: specifies division factor for OTG FS, SDIO and RNG clocks. - * This parameter must be a number in the range {2, 4, 6, or 8}. - * @note the PLLSAIP parameter is only available with STM32F446xx Devices - * - * @param __PLLSAIQ__: specifies the division factor for SAI clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 15. - * - * @param __PLLSAIR__: specifies the division factor for LTDC clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 7. - * @note the PLLI2SR parameter is only available with STM32F427/437/429/439xx Devices - */ -#define __HAL_RCC_PLLSAI_CONFIG(__PLLSAIM__, __PLLSAIN__, __PLLSAIP__, __PLLSAIQ__, __PLLSAIR__) \ - (RCC->PLLSAICFGR = ((__PLLSAIM__) | \ - ((__PLLSAIN__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIN)) | \ - ((((__PLLSAIP__) >> 1) -1) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIP)) | \ - ((__PLLSAIQ__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ)))) -#endif /* STM32F446xx */ - -#if defined(STM32F469xx) || defined(STM32F479xx) -/** @brief Macro to configure the PLLSAI clock multiplication and division factors. - * - * @param __PLLSAIN__: specifies the multiplication factor for PLLSAI VCO output clock. - * This parameter must be a number between Min_Data = 50 and Max_Data = 432. - * @note You have to set the PLLSAIN parameter correctly to ensure that the VCO - * output frequency is between Min_Data = 100 and Max_Data = 432 MHz. - * - * @param __PLLSAIP__: specifies division factor for SDIO and CLK48 clocks. - * This parameter must be a number in the range {2, 4, 6, or 8}. - * - * @param __PLLSAIQ__: specifies the division factor for SAI clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 15. - * - * @param __PLLSAIR__: specifies the division factor for LTDC clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 7. - */ -#define __HAL_RCC_PLLSAI_CONFIG(__PLLSAIN__, __PLLSAIP__, __PLLSAIQ__, __PLLSAIR__) \ - (RCC->PLLSAICFGR = (((__PLLSAIN__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIN)) |\ - ((((__PLLSAIP__) >> 1) -1) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIP)) |\ - ((__PLLSAIQ__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ)) |\ - ((__PLLSAIR__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIR)))) -#endif /* STM32F469xx || STM32F479xx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) -/** @brief Macro to configure the PLLSAI clock multiplication and division factors. - * - * @param __PLLSAIN__: specifies the multiplication factor for PLLSAI VCO output clock. - * This parameter must be a number between Min_Data = 50 and Max_Data = 432. - * @note You have to set the PLLSAIN parameter correctly to ensure that the VCO - * output frequency is between Min_Data = 100 and Max_Data = 432 MHz. - * - * @param __PLLSAIQ__: specifies the division factor for SAI clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 15. - * - * @param __PLLSAIR__: specifies the division factor for LTDC clock - * This parameter must be a number between Min_Data = 2 and Max_Data = 7. - * @note the PLLI2SR parameter is only available with STM32F427/437/429/439xx Devices - */ -#define __HAL_RCC_PLLSAI_CONFIG(__PLLSAIN__, __PLLSAIQ__, __PLLSAIR__) \ - (RCC->PLLSAICFGR = (((__PLLSAIN__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIN)) | \ - ((__PLLSAIQ__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ)) | \ - ((__PLLSAIR__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIR)))) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */ - -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */ -/*----------------------------------------------------------------------------*/ - -/*------------------- PLLSAI/PLLI2S Dividers Configuration -------------------*/ -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx) ||\ - defined(STM32F469xx) || defined(STM32F479xx) -/** @brief Macro to configure the SAI clock Divider coming from PLLI2S. - * @note This function must be called before enabling the PLLI2S. - * @param __PLLI2SDivQ__: specifies the PLLI2S division factor for SAI1 clock. - * This parameter must be a number between 1 and 32. - * SAI1 clock frequency = f(PLLI2SQ) / __PLLI2SDivQ__ - */ -#define __HAL_RCC_PLLI2S_PLLSAICLKDIVQ_CONFIG(__PLLI2SDivQ__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_PLLI2SDIVQ, (__PLLI2SDivQ__)-1)) - -/** @brief Macro to configure the SAI clock Divider coming from PLLSAI. - * @note This function must be called before enabling the PLLSAI. - * @param __PLLSAIDivQ__: specifies the PLLSAI division factor for SAI1 clock . - * This parameter must be a number between Min_Data = 1 and Max_Data = 32. - * SAI1 clock frequency = f(PLLSAIQ) / __PLLSAIDivQ__ - */ -#define __HAL_RCC_PLLSAI_PLLSAICLKDIVQ_CONFIG(__PLLSAIDivQ__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_PLLSAIDIVQ, ((__PLLSAIDivQ__)-1)<<8)) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) -/** @brief Macro to configure the LTDC clock Divider coming from PLLSAI. - * - * @note The LTDC peripheral is only available with STM32F427/437/429/439/469/479xx Devices. - * @note This function must be called before enabling the PLLSAI. - * @param __PLLSAIDivR__: specifies the PLLSAI division factor for LTDC clock . - * This parameter must be a number between Min_Data = 2 and Max_Data = 16. - * LTDC clock frequency = f(PLLSAIR) / __PLLSAIDivR__ - */ -#define __HAL_RCC_PLLSAI_PLLSAICLKDIVR_CONFIG(__PLLSAIDivR__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_PLLSAIDIVR, (__PLLSAIDivR__))) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ -/*----------------------------------------------------------------------------*/ - -/*------------------------- Peripheral Clock selection -----------------------*/ -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) ||\ - defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F469xx) ||\ - defined(STM32F479xx) -/** @brief Macro to configure the I2S clock source (I2SCLK). - * @note This function must be called before enabling the I2S APB clock. - * @param __SOURCE__: specifies the I2S clock source. - * This parameter can be one of the following values: - * @arg RCC_I2SCLKSOURCE_PLLI2S: PLLI2S clock used as I2S clock source. - * @arg RCC_I2SCLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin - * used as I2S clock source. - */ -#define __HAL_RCC_I2S_CONFIG(__SOURCE__) (*(__IO uint32_t *) RCC_CFGR_I2SSRC_BB = (__SOURCE__)) -#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) - -/** @brief Macro to configure SAI1BlockA clock source selection. - * @note The SAI peripheral is only available with STM32F427/437/429/439/469/479xx Devices. - * @note This function must be called before enabling PLLSAI, PLLI2S and - * the SAI clock. - * @param __SOURCE__: specifies the SAI Block A clock source. - * This parameter can be one of the following values: - * @arg RCC_SAIACLKSOURCE_PLLI2S: PLLI2S_Q clock divided by PLLI2SDIVQ used - * as SAI1 Block A clock. - * @arg RCC_SAIACLKSOURCE_PLLSAI: PLLISAI_Q clock divided by PLLSAIDIVQ used - * as SAI1 Block A clock. - * @arg RCC_SAIACLKSOURCE_Ext: External clock mapped on the I2S_CKIN pin - * used as SAI1 Block A clock. - */ -#define __HAL_RCC_SAI_BLOCKACLKSOURCE_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_SAI1ASRC, (__SOURCE__))) - -/** @brief Macro to configure SAI1BlockB clock source selection. - * @note The SAI peripheral is only available with STM32F427/437/429/439/469/479xx Devices. - * @note This function must be called before enabling PLLSAI, PLLI2S and - * the SAI clock. - * @param __SOURCE__: specifies the SAI Block B clock source. - * This parameter can be one of the following values: - * @arg RCC_SAIBCLKSOURCE_PLLI2S: PLLI2S_Q clock divided by PLLI2SDIVQ used - * as SAI1 Block B clock. - * @arg RCC_SAIBCLKSOURCE_PLLSAI: PLLISAI_Q clock divided by PLLSAIDIVQ used - * as SAI1 Block B clock. - * @arg RCC_SAIBCLKSOURCE_Ext: External clock mapped on the I2S_CKIN pin - * used as SAI1 Block B clock. - */ -#define __HAL_RCC_SAI_BLOCKBCLKSOURCE_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_SAI1BSRC, (__SOURCE__))) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F446xx) -/** @brief Macro to configure SAI1 clock source selection. - * @note This configuration is only available with STM32F446xx Devices. - * @note This function must be called before enabling PLL, PLLSAI, PLLI2S and - * the SAI clock. - * @param __SOURCE__: specifies the SAI1 clock source. - * This parameter can be one of the following values: - * @arg RCC_SAI1CLKSOURCE_PLLI2S: PLLI2S_Q clock divided by PLLI2SDIVQ used as SAI1 clock. - * @arg RCC_SAI1CLKSOURCE_PLLSAI: PLLISAI_Q clock divided by PLLSAIDIVQ used as SAI1 clock. - * @arg RCC_SAI1CLKSOURCE_PLLR: PLL VCO Output divided by PLLR used as SAI1 clock. - * @arg RCC_SAI1CLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin used as SAI1 clock. - */ -#define __HAL_RCC_SAI1_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_SAI1SRC, (__SOURCE__))) - -/** @brief Macro to Get SAI1 clock source selection. - * @note This configuration is only available with STM32F446xx Devices. - * @retval The clock source can be one of the following values: - * @arg RCC_SAI1CLKSOURCE_PLLI2S: PLLI2S_Q clock divided by PLLI2SDIVQ used as SAI1 clock. - * @arg RCC_SAI1CLKSOURCE_PLLSAI: PLLISAI_Q clock divided by PLLSAIDIVQ used as SAI1 clock. - * @arg RCC_SAI1CLKSOURCE_PLLR: PLL VCO Output divided by PLLR used as SAI1 clock. - * @arg RCC_SAI1CLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin used as SAI1 clock. - */ -#define __HAL_RCC_GET_SAI1_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_SAI1SRC)) - -/** @brief Macro to configure SAI2 clock source selection. - * @note This configuration is only available with STM32F446xx Devices. - * @note This function must be called before enabling PLL, PLLSAI, PLLI2S and - * the SAI clock. - * @param __SOURCE__: specifies the SAI2 clock source. - * This parameter can be one of the following values: - * @arg RCC_SAI2CLKSOURCE_PLLI2S: PLLI2S_Q clock divided by PLLI2SDIVQ used as SAI2 clock. - * @arg RCC_SAI2CLKSOURCE_PLLSAI: PLLISAI_Q clock divided by PLLSAIDIVQ used as SAI2 clock. - * @arg RCC_SAI2CLKSOURCE_PLLR: PLL VCO Output divided by PLLR used as SAI2 clock. - * @arg RCC_SAI2CLKSOURCE_PLLSRC: HSI or HSE depending from PLL Source clock used as SAI2 clock. - */ -#define __HAL_RCC_SAI2_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_SAI2SRC, (__SOURCE__))) - -/** @brief Macro to Get SAI2 clock source selection. - * @note This configuration is only available with STM32F446xx Devices. - * @retval The clock source can be one of the following values: - * @arg RCC_SAI2CLKSOURCE_PLLI2S: PLLI2S_Q clock divided by PLLI2SDIVQ used as SAI2 clock. - * @arg RCC_SAI2CLKSOURCE_PLLSAI: PLLISAI_Q clock divided by PLLSAIDIVQ used as SAI2 clock. - * @arg RCC_SAI2CLKSOURCE_PLLR: PLL VCO Output divided by PLLR used as SAI2 clock. - * @arg RCC_SAI2CLKSOURCE_PLLSRC: HSI or HSE depending from PLL Source clock used as SAI2 clock. - */ -#define __HAL_RCC_GET_SAI2_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_SAI2SRC)) - -/** @brief Macro to configure I2S APB1 clock source selection. - * @note This function must be called before enabling PLL, PLLI2S and the I2S clock. - * @param __SOURCE__: specifies the I2S APB1 clock source. - * This parameter can be one of the following values: - * @arg RCC_I2SAPB1CLKSOURCE_PLLI2S: PLLI2S VCO output clock divided by PLLI2SR used as I2S clock. - * @arg RCC_I2SAPB1CLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin used as SAI1 clock. - * @arg RCC_I2SAPB1CLKSOURCE_PLLR: PLL VCO Output divided by PLLR used as SAI1 clock. - * @arg RCC_I2SAPB1CLKSOURCE_PLLSRC: HSI or HSE depending from PLL source Clock. - */ -#define __HAL_RCC_I2S_APB1_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_I2S1SRC, (__SOURCE__))) - -/** @brief Macro to Get I2S APB1 clock source selection. - * @retval The clock source can be one of the following values: - * @arg RCC_I2SAPB1CLKSOURCE_PLLI2S: PLLI2S VCO output clock divided by PLLI2SR used as I2S clock. - * @arg RCC_I2SAPB1CLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin used as SAI1 clock. - * @arg RCC_I2SAPB1CLKSOURCE_PLLR: PLL VCO Output divided by PLLR used as SAI1 clock. - * @arg RCC_I2SAPB1CLKSOURCE_PLLSRC: HSI or HSE depending from PLL source Clock. - */ -#define __HAL_RCC_GET_I2S_APB1_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_I2S1SRC)) - -/** @brief Macro to configure I2S APB2 clock source selection. - * @note This function must be called before enabling PLL, PLLI2S and the I2S clock. - * @param __SOURCE__: specifies the SAI Block A clock source. - * This parameter can be one of the following values: - * @arg RCC_I2SAPB2CLKSOURCE_PLLI2S: PLLI2S VCO output clock divided by PLLI2SR used as I2S clock. - * @arg RCC_I2SAPB2CLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin used as SAI1 clock. - * @arg RCC_I2SAPB2CLKSOURCE_PLLR: PLL VCO Output divided by PLLR used as SAI1 clock. - * @arg RCC_I2SAPB2CLKSOURCE_PLLSRC: HSI or HSE depending from PLL source Clock. - */ -#define __HAL_RCC_I2S_APB2_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_I2S2SRC, (__SOURCE__))) - -/** @brief Macro to Get I2S APB2 clock source selection. - * @retval The clock source can be one of the following values: - * @arg RCC_I2SAPB2CLKSOURCE_PLLI2S: PLLI2S VCO output clock divided by PLLI2SR used as I2S clock. - * @arg RCC_I2SAPB2CLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin used as SAI1 clock. - * @arg RCC_I2SAPB2CLKSOURCE_PLLR: PLL VCO Output divided by PLLR used as SAI1 clock. - * @arg RCC_I2SAPB2CLKSOURCE_PLLSRC: HSI or HSE depending from PLL source Clock. - */ -#define __HAL_RCC_GET_I2S_APB2_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_I2S2SRC)) - -/** @brief Macro to configure the CEC clock. - * @param __SOURCE__: specifies the CEC clock source. - * This parameter can be one of the following values: - * @arg RCC_CECCLKSOURCE_HSI: HSI selected as CEC clock - * @arg RCC_CECCLKSOURCE_LSE: LSE selected as CEC clock - */ -#define __HAL_RCC_CEC_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_CECSEL, (uint32_t)(__SOURCE__))) - -/** @brief Macro to Get the CEC clock. - * @retval The clock source can be one of the following values: - * @arg RCC_CECCLKSOURCE_HSI488: HSI selected as CEC clock - * @arg RCC_CECCLKSOURCE_LSE: LSE selected as CEC clock - */ -#define __HAL_RCC_GET_CEC_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_CECSEL)) - -/** @brief Macro to configure the FMPI2C1 clock. - * @param __SOURCE__: specifies the FMPI2C1 clock source. - * This parameter can be one of the following values: - * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as FMPI2C1 clock - * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as FMPI2C1 clock - * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as FMPI2C1 clock - */ -#define __HAL_RCC_FMPI2C1_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_FMPI2C1SEL, (uint32_t)(__SOURCE__))) - -/** @brief Macro to Get the FMPI2C1 clock. - * @retval The clock source can be one of the following values: - * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as FMPI2C1 clock - * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as FMPI2C1 clock - * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as FMPI2C1 clock - */ -#define __HAL_RCC_GET_FMPI2C1_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_FMPI2C1SEL)) - -/** @brief Macro to configure the CLK48 clock. - * @param __SOURCE__: specifies the CLK48 clock source. - * This parameter can be one of the following values: - * @arg RCC_CLK48CLKSOURCE_PLLQ: PLL VCO Output divided by PLLQ used as CLK48 clock. - * @arg RCC_CLK48CLKSOURCE_PLLSAIP: PLLSAI VCO Output divided by PLLSAIP used as CLK48 clock. - */ -#define __HAL_RCC_CLK48_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_CK48MSEL, (uint32_t)(__SOURCE__))) - -/** @brief Macro to Get the CLK48 clock. - * @retval The clock source can be one of the following values: - * @arg RCC_CLK48CLKSOURCE_PLLQ: PLL VCO Output divided by PLLQ used as CLK48 clock. - * @arg RCC_CLK48CLKSOURCE_PLLSAIP: PLLSAI VCO Output divided by PLLSAIP used as CLK48 clock. - */ -#define __HAL_RCC_GET_CLK48_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_CK48MSEL)) - -/** @brief Macro to configure the SDIO clock. - * @param __SOURCE__: specifies the SDIO clock source. - * This parameter can be one of the following values: - * @arg RCC_SDIOCLKSOURCE_CLK48: CLK48 output used as SDIO clock. - * @arg RCC_SDIOCLKSOURCE_SYSCLK: System clock output used as SDIO clock. - */ -#define __HAL_RCC_SDIO_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_SDIOSEL, (uint32_t)(__SOURCE__))) - -/** @brief Macro to Get the SDIO clock. - * @retval The clock source can be one of the following values: - * @arg RCC_SDIOCLKSOURCE_CLK48: CLK48 output used as SDIO clock. - * @arg RCC_SDIOCLKSOURCE_SYSCLK: System clock output used as SDIO clock. - */ -#define __HAL_RCC_GET_SDIO_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_SDIOSEL)) - -/** @brief Macro to configure the SPDIFRX clock. - * @param __SOURCE__: specifies the SPDIFRX clock source. - * This parameter can be one of the following values: - * @arg RCC_SPDIFRXCLKSOURCE_PLLR: PLL VCO Output divided by PLLR used as SPDIFRX clock. - * @arg RCC_SPDIFRXCLKSOURCE_PLLI2SP: PLLI2S VCO Output divided by PLLI2SP used as SPDIFRX clock. - */ -#define __HAL_RCC_SPDIFRX_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_SPDIFRXSEL, (uint32_t)(__SOURCE__))) - -/** @brief Macro to Get the SPDIFRX clock. - * @retval The clock source can be one of the following values: - * @arg RCC_SPDIFRXCLKSOURCE_PLLR: PLL VCO Output divided by PLLR used as SPDIFRX clock. - * @arg RCC_SPDIFRXCLKSOURCE_PLLI2SP: PLLI2S VCO Output divided by PLLI2SP used as SPDIFRX clock. - */ -#define __HAL_RCC_GET_SPDIFRX_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_SPDIFRXSEL)) -#endif /* STM32F446xx */ - -#if defined(STM32F469xx) || defined(STM32F479xx) - -/** @brief Macro to configure the CLK48 clock. - * @param __SOURCE__: specifies the CLK48 clock source. - * This parameter can be one of the following values: - * @arg RCC_CLK48CLKSOURCE_PLLQ: PLL VCO Output divided by PLLQ used as CLK48 clock. - * @arg RCC_CLK48CLKSOURCE_PLLSAIP: PLLSAI VCO Output divided by PLLSAIP used as CLK48 clock. - */ -#define __HAL_RCC_CLK48_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_CK48MSEL, (uint32_t)(__SOURCE__))) - -/** @brief Macro to Get the CLK48 clock. - * @retval The clock source can be one of the following values: - * @arg RCC_CLK48CLKSOURCE_PLLQ: PLL VCO Output divided by PLLQ used as CLK48 clock. - * @arg RCC_CLK48CLKSOURCE_PLLSAIP: PLLSAI VCO Output divided by PLLSAIP used as CLK48 clock. - */ -#define __HAL_RCC_GET_CLK48_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_CK48MSEL)) - -/** @brief Macro to configure the SDIO clock. - * @param __SOURCE__: specifies the SDIO clock source. - * This parameter can be one of the following values: - * @arg RCC_SDIOCLKSOURCE_CLK48: CLK48 output used as SDIO clock. - * @arg RCC_SDIOCLKSOURCE_SYSCLK: System clock output used as SDIO clock. - */ -#define __HAL_RCC_SDIO_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_SDIOSEL, (uint32_t)(__SOURCE__))) - -/** @brief Macro to Get the SDIO clock. - * @retval The clock source can be one of the following values: - * @arg RCC_SDIOCLKSOURCE_CLK48: CLK48 output used as SDIO clock. - * @arg RCC_SDIOCLKSOURCE_SYSCLK: System clock output used as SDIO clock. - */ -#define __HAL_RCC_GET_SDIO_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_SDIOSEL)) - -/** @brief Macro to configure the DSI clock. - * @param __SOURCE__: specifies the DSI clock source. - * This parameter can be one of the following values: - * @arg RCC_DSICLKSOURCE_PLLR: PLLR output used as DSI clock. - * @arg RCC_DSICLKSOURCE_DSIPHY: DSI-PHY output used as DSI clock. - */ -#define __HAL_RCC_DSI_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_DSISEL, (uint32_t)(__SOURCE__))) - -/** @brief Macro to Get the DSI clock. - * @retval The clock source can be one of the following values: - * @arg RCC_DSICLKSOURCE_PLLR: PLLR output used as DSI clock. - * @arg RCC_DSICLKSOURCE_DSIPHY: DSI-PHY output used as DSI clock. - */ -#define __HAL_RCC_GET_DSI_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_DSISEL)) - -#endif /* STM32F469xx || STM32F479xx */ - -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -/** @brief Macro to configure the DFSDM1 clock. - * @param __DFSDM1_CLKSOURCE__: specifies the DFSDM1 clock source. - * This parameter can be one of the following values: - * @arg RCC_DFSDM1CLKSOURCE_APB2: APB2 clock used as kernel clock. - * @arg RCC_DFSDM1CLKSOURCE_SYSCLK: System clock used as kernal clock. - * @retval None - */ -#define __HAL_RCC_DFSDM1_CONFIG(__DFSDM1_CLKSOURCE__) MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_CKDFSDM1SEL, (__DFSDM1_CLKSOURCE__)) - -/** @brief Macro to get the DFSDM1 clock source. - * @retval The clock source can be one of the following values: - * @arg RCC_DFSDM1CLKSOURCE_APB2: APB2 clock used as kernel clock. - * @arg RCC_DFSDM1CLKSOURCE_SYSCLK: System clock used as kernal clock. - */ -#define __HAL_RCC_GET_DFSDM1_SOURCE() ((uint32_t)(READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_CKDFSDM1SEL))) - -/** @brief Macro to configure DFSDM1 Audio clock source selection. - * @note This configuration is only available with STM32F412Zx/STM32F412Vx/STM32F412Rx/STM32F412Cx Devices. - * @param __SOURCE__: specifies the DFSDM1 Audio clock source. - * This parameter can be one of the following values: - * @arg RCC_DFSDM1AUDIOCLKSOURCE_I2SAPB1: CK_I2S_APB1 selected as audio clock - * @arg RCC_DFSDM1AUDIOCLKSOURCE_I2SAPB2: CK_I2S_APB2 selected as audio clock - */ -#define __HAL_RCC_DFSDM1AUDIO_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_CKDFSDM1ASEL, (__SOURCE__))) - -/** @brief Macro to Get DFSDM1 Audio clock source selection. - * @note This configuration is only available with STM32F412Zx/STM32F412Vx/STM32F412Rx/STM32F412Cx Devices. - * @retval The clock source can be one of the following values: - * @arg RCC_DFSDM1AUDIOCLKSOURCE_I2SAPB1: CK_I2S_APB1 selected as audio clock - * @arg RCC_DFSDM1AUDIOCLKSOURCE_I2SAPB2: CK_I2S_APB2 selected as audio clock - */ -#define __HAL_RCC_GET_DFSDM1AUDIO_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_CKDFSDM1ASEL)) - -/** @brief Macro to configure I2S APB1 clock source selection. - * @param __SOURCE__: specifies the I2S APB1 clock source. - * This parameter can be one of the following values: - * @arg RCC_I2SAPB1CLKSOURCE_PLLI2S: PLLI2S VCO output clock divided by PLLI2SR. - * @arg RCC_I2SAPB1CLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin. - * @arg RCC_I2SAPB1CLKSOURCE_PLLR: PLL VCO Output divided by PLLR. - * @arg RCC_I2SAPB1CLKSOURCE_PLLSRC: HSI or HSE depending from PLL source Clock. - */ -#define __HAL_RCC_I2S_APB1_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_I2S1SRC, (__SOURCE__))) - -/** @brief Macro to Get I2S APB1 clock source selection. - * @retval The clock source can be one of the following values: - * @arg RCC_I2SAPB1CLKSOURCE_PLLI2S: PLLI2S VCO output clock divided by PLLI2SR. - * @arg RCC_I2SAPB1CLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin. - * @arg RCC_I2SAPB1CLKSOURCE_PLLR: PLL VCO Output divided by PLLR. - * @arg RCC_I2SAPB1CLKSOURCE_PLLSRC: HSI or HSE depending from PLL source Clock. - */ -#define __HAL_RCC_GET_I2S_APB1_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_I2S1SRC)) - -/** @brief Macro to configure I2S APB2 clock source selection. - * @param __SOURCE__: specifies the I2S APB2 clock source. - * This parameter can be one of the following values: - * @arg RCC_I2SAPB2CLKSOURCE_PLLI2S: PLLI2S VCO output clock divided by PLLI2SR. - * @arg RCC_I2SAPB2CLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin. - * @arg RCC_I2SAPB2CLKSOURCE_PLLR: PLL VCO Output divided by PLLR. - * @arg RCC_I2SAPB2CLKSOURCE_PLLSRC: HSI or HSE depending from PLL source Clock. - */ -#define __HAL_RCC_I2S_APB2_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_I2S2SRC, (__SOURCE__))) - -/** @brief Macro to Get I2S APB2 clock source selection. - * @retval The clock source can be one of the following values: - * @arg RCC_I2SAPB2CLKSOURCE_PLLI2S: PLLI2S VCO output clock divided by PLLI2SR. - * @arg RCC_I2SAPB2CLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin. - * @arg RCC_I2SAPB2CLKSOURCE_PLLR: PLL VCO Output divided by PLLR. - * @arg RCC_I2SAPB2CLKSOURCE_PLLSRC: HSI or HSE depending from PLL source Clock. - */ -#define __HAL_RCC_GET_I2S_APB2_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_I2S2SRC)) - -/** @brief Macro to configure the PLL I2S clock source (PLLI2SCLK). - * @note This macro must be called before enabling the I2S APB clock. - * @param __SOURCE__: specifies the I2S clock source. - * This parameter can be one of the following values: - * @arg RCC_PLLI2SCLKSOURCE_PLLSRC: HSI or HSE depending from PLL source Clock. - * @arg RCC_PLLI2SCLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin - * used as I2S clock source. - */ -#define __HAL_RCC_PLL_I2S_CONFIG(__SOURCE__) (*(__IO uint32_t *) RCC_PLLI2SCFGR_PLLI2SSRC_BB = (__SOURCE__)) - -/** @brief Macro to configure the FMPI2C1 clock. - * @param __SOURCE__: specifies the FMPI2C1 clock source. - * This parameter can be one of the following values: - * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as FMPI2C1 clock - * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as FMPI2C1 clock - * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as FMPI2C1 clock - */ -#define __HAL_RCC_FMPI2C1_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_FMPI2C1SEL, (uint32_t)(__SOURCE__))) - -/** @brief Macro to Get the FMPI2C1 clock. - * @retval The clock source can be one of the following values: - * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as FMPI2C1 clock - * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as FMPI2C1 clock - * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as FMPI2C1 clock - */ -#define __HAL_RCC_GET_FMPI2C1_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_FMPI2C1SEL)) - -/** @brief Macro to configure the CLK48 clock. - * @param __SOURCE__: specifies the CLK48 clock source. - * This parameter can be one of the following values: - * @arg RCC_CLK48CLKSOURCE_PLLQ: PLL VCO Output divided by PLLQ used as CLK48 clock. - * @arg RCC_CLK48CLKSOURCE_PLLI2SQ: PLLI2S VCO Output divided by PLLI2SQ used as CLK48 clock. - */ -#define __HAL_RCC_CLK48_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_CK48MSEL, (uint32_t)(__SOURCE__))) - -/** @brief Macro to Get the CLK48 clock. - * @retval The clock source can be one of the following values: - * @arg RCC_CLK48CLKSOURCE_PLLQ: PLL VCO Output divided by PLLQ used as CLK48 clock. - * @arg RCC_CLK48CLKSOURCE_PLLI2SQ: PLLI2S VCO Output divided by PLLI2SQ used as CLK48 clock - */ -#define __HAL_RCC_GET_CLK48_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_CK48MSEL)) - -/** @brief Macro to configure the SDIO clock. - * @param __SOURCE__: specifies the SDIO clock source. - * This parameter can be one of the following values: - * @arg RCC_SDIOCLKSOURCE_CLK48: CLK48 output used as SDIO clock. - * @arg RCC_SDIOCLKSOURCE_SYSCLK: System clock output used as SDIO clock. - */ -#define __HAL_RCC_SDIO_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_SDIOSEL, (uint32_t)(__SOURCE__))) - -/** @brief Macro to Get the SDIO clock. - * @retval The clock source can be one of the following values: - * @arg RCC_SDIOCLKSOURCE_CLK48: CLK48 output used as SDIO clock. - * @arg RCC_SDIOCLKSOURCE_SYSCLK: System clock output used as SDIO clock. - */ -#define __HAL_RCC_GET_SDIO_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_SDIOSEL)) - -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -/** @brief Macro to configure I2S clock source selection. - * @param __SOURCE__: specifies the I2S clock source. - * This parameter can be one of the following values: - * @arg RCC_I2SAPBCLKSOURCE_PLLR: PLL VCO output clock divided by PLLR. - * @arg RCC_I2SAPBCLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin. - * @arg RCC_I2SAPBCLKSOURCE_PLLSRC: HSI/HSE depends on PLLSRC. - */ -#define __HAL_RCC_I2S_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_I2SSRC, (__SOURCE__))) - -/** @brief Macro to Get I2S clock source selection. - * @retval The clock source can be one of the following values: - * @arg RCC_I2SAPBCLKSOURCE_PLLR: PLL VCO output clock divided by PLLR. - * @arg RCC_I2SAPBCLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin. - * @arg RCC_I2SAPBCLKSOURCE_PLLSRC: HSI/HSE depends on PLLSRC. - */ -#define __HAL_RCC_GET_I2S_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_I2SSRC)) - -/** @brief Macro to configure the FMPI2C1 clock. - * @param __SOURCE__: specifies the FMPI2C1 clock source. - * This parameter can be one of the following values: - * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as FMPI2C1 clock - * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as FMPI2C1 clock - * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as FMPI2C1 clock - */ -#define __HAL_RCC_FMPI2C1_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_FMPI2C1SEL, (uint32_t)(__SOURCE__))) - -/** @brief Macro to Get the FMPI2C1 clock. - * @retval The clock source can be one of the following values: - * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as FMPI2C1 clock - * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as FMPI2C1 clock - * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as FMPI2C1 clock - */ -#define __HAL_RCC_GET_FMPI2C1_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_FMPI2C1SEL)) - -/** @brief Macro to configure the LPTIM1 clock. - * @param __SOURCE__: specifies the LPTIM1 clock source. - * This parameter can be one of the following values: - * @arg RCC_LPTIM1CLKSOURCE_PCLK: APB selected as LPTIM1 clock - * @arg RCC_LPTIM1CLKSOURCE_HSI: HSI clock selected as LPTIM1 clock - * @arg RCC_LPTIM1CLKSOURCE_LSI: LSI selected as LPTIM1 clock - * @arg RCC_LPTIM1CLKSOURCE_LSE: LSE selected as LPTIM1 clock - */ -#define __HAL_RCC_LPTIM1_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_LPTIM1SEL, (uint32_t)(__SOURCE__))) - -/** @brief Macro to Get the LPTIM1 clock. - * @retval The clock source can be one of the following values: - * @arg RCC_LPTIM1CLKSOURCE_PCLK: APB selected as LPTIM1 clock - * @arg RCC_LPTIM1CLKSOURCE_HSI: HSI clock selected as LPTIM1 clock - * @arg RCC_LPTIM1CLKSOURCE_LSI: LSI selected as LPTIM1 clock - * @arg RCC_LPTIM1CLKSOURCE_LSE: LSE selected as LPTIM1 clock - */ -#define __HAL_RCC_GET_LPTIM1_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_LPTIM1SEL)) -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) ||\ - defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F469xx) ||\ - defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) ||\ - defined(STM32F412Cx) -/** @brief Macro to configure the Timers clocks prescalers - * @note This feature is only available with STM32F429x/439x Devices. - * @param __PRESC__ : specifies the Timers clocks prescalers selection - * This parameter can be one of the following values: - * @arg RCC_TIMPRES_DESACTIVATED: The Timers kernels clocks prescaler is - * equal to HPRE if PPREx is corresponding to division by 1 or 2, - * else it is equal to [(HPRE * PPREx) / 2] if PPREx is corresponding to - * division by 4 or more. - * @arg RCC_TIMPRES_ACTIVATED: The Timers kernels clocks prescaler is - * equal to HPRE if PPREx is corresponding to division by 1, 2 or 4, - * else it is equal to [(HPRE * PPREx) / 4] if PPREx is corresponding - * to division by 8 or more. - */ -#define __HAL_RCC_TIMCLKPRESCALER(__PRESC__) (*(__IO uint32_t *) RCC_DCKCFGR_TIMPRE_BB = (__PRESC__)) - -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx) || STM32F401xC || STM32F401xE || STM32F410xx || STM32F411xE ||\ - STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -/*----------------------------------------------------------------------------*/ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) -/** @brief Enable PLLSAI_RDY interrupt. - */ -#define __HAL_RCC_PLLSAI_ENABLE_IT() (RCC->CIR |= (RCC_CIR_PLLSAIRDYIE)) - -/** @brief Disable PLLSAI_RDY interrupt. - */ -#define __HAL_RCC_PLLSAI_DISABLE_IT() (RCC->CIR &= ~(RCC_CIR_PLLSAIRDYIE)) - -/** @brief Clear the PLLSAI RDY interrupt pending bits. - */ -#define __HAL_RCC_PLLSAI_CLEAR_IT() (RCC->CIR |= (RCC_CIR_PLLSAIRDYF)) - -/** @brief Check the PLLSAI RDY interrupt has occurred or not. - * @retval The new state (TRUE or FALSE). - */ -#define __HAL_RCC_PLLSAI_GET_IT() ((RCC->CIR & (RCC_CIR_PLLSAIRDYIE)) == (RCC_CIR_PLLSAIRDYIE)) - -/** @brief Check PLLSAI RDY flag is set or not. - * @retval The new state (TRUE or FALSE). - */ -#define __HAL_RCC_PLLSAI_GET_FLAG() ((RCC->CR & (RCC_CR_PLLSAIRDY)) == (RCC_CR_PLLSAIRDY)) - -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -/** @brief Macros to enable or disable the RCC MCO1 feature. - */ -#define __HAL_RCC_MCO1_ENABLE() (*(__IO uint32_t *) RCC_CFGR_MCO1EN_BB = ENABLE) -#define __HAL_RCC_MCO1_DISABLE() (*(__IO uint32_t *) RCC_CFGR_MCO1EN_BB = DISABLE) - -/** @brief Macros to enable or disable the RCC MCO2 feature. - */ -#define __HAL_RCC_MCO2_ENABLE() (*(__IO uint32_t *) RCC_CFGR_MCO2EN_BB = ENABLE) -#define __HAL_RCC_MCO2_DISABLE() (*(__IO uint32_t *) RCC_CFGR_MCO2EN_BB = DISABLE) - -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -/** - * @} - */ - -/* Exported functions --------------------------------------------------------*/ -/** @addtogroup RCCEx_Exported_Functions - * @{ - */ - -/** @addtogroup RCCEx_Exported_Functions_Group1 - * @{ - */ -HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit); -void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit); - -#if defined(STM32F446xx) -uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk); -#endif /* STM32F446xx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F411xE) ||\ - defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) ||\ - defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -void HAL_RCCEx_SelectLSEMode(uint8_t Mode); -#endif /* STM32F410xx || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ -/** - * @} - */ - -/** - * @} - */ -/* Private types -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/* Private constants ---------------------------------------------------------*/ -/** @defgroup RCCEx_Private_Constants RCCEx Private Constants - * @{ - */ - -/** @defgroup RCCEx_BitAddress_AliasRegion RCC BitAddress AliasRegion - * @brief RCC registers bit address in the alias region - * @{ - */ -/* --- CR Register ---*/ -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) -/* Alias word address of PLLSAION bit */ -#define RCC_PLLSAION_BIT_NUMBER 0x1C -#define RCC_CR_PLLSAION_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32) + (RCC_PLLSAION_BIT_NUMBER * 4)) - -#define PLLSAI_TIMEOUT_VALUE ((uint32_t)2) /* Timeout value fixed to 2 ms */ -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \ - defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \ - defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ - defined(STM32F412Rx) || defined(STM32F412Cx) -/* Alias word address of PLLI2SON bit */ -#define RCC_PLLI2SON_BIT_NUMBER 0x1A -#define RCC_CR_PLLI2SON_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32) + (RCC_PLLI2SON_BIT_NUMBER * 4)) -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || - STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || - STM32F412Rx || STM32F412Cx */ - -/* --- DCKCFGR Register ---*/ -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F401xC) ||\ - defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F469xx) ||\ - defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) ||\ - defined(STM32F412Cx) -/* Alias word address of TIMPRE bit */ -#define RCC_DCKCFGR_OFFSET (RCC_OFFSET + 0x8C) -#define RCC_TIMPRE_BIT_NUMBER 0x18 -#define RCC_DCKCFGR_TIMPRE_BB (PERIPH_BB_BASE + (RCC_DCKCFGR_OFFSET * 32) + (RCC_TIMPRE_BIT_NUMBER * 4)) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F410xx || STM32F401xC ||\ - STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx ||\ - STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -/* --- CFGR Register ---*/ -#define RCC_CFGR_OFFSET (RCC_OFFSET + 0x08U) -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \ - defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \ - defined(STM32F469xx) || defined(STM32F479xx) -/* Alias word address of I2SSRC bit */ -#define RCC_I2SSRC_BIT_NUMBER 0x17 -#define RCC_CFGR_I2SSRC_BB (PERIPH_BB_BASE + (RCC_CFGR_OFFSET * 32) + (RCC_I2SSRC_BIT_NUMBER * 4)) - -#define PLLI2S_TIMEOUT_VALUE ((uint32_t)2) /* Timeout value fixed to 2 ms */ -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || - STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -/* --- PLLI2SCFGR Register ---*/ -#define RCC_PLLI2SCFGR_OFFSET (RCC_OFFSET + 0x84U) -/* Alias word address of PLLI2SSRC bit */ -#define RCC_PLLI2SSRC_BIT_NUMBER 0x16 -#define RCC_PLLI2SCFGR_PLLI2SSRC_BB (PERIPH_BB_BASE + (RCC_PLLI2SCFGR_OFFSET * 32) + (RCC_PLLI2SSRC_BIT_NUMBER * 4)) - -#define PLLI2S_TIMEOUT_VALUE ((uint32_t)2) /* Timeout value fixed to 2 ms */ -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -/* Alias word address of MCO1EN bit */ -#define RCC_MCO1EN_BIT_NUMBER 0x8 -#define RCC_CFGR_MCO1EN_BB (PERIPH_BB_BASE + (RCC_CFGR_OFFSET * 32) + (RCC_MCO1EN_BIT_NUMBER * 4)) - -/* Alias word address of MCO2EN bit */ -#define RCC_MCO2EN_BIT_NUMBER 0x9 -#define RCC_CFGR_MCO2EN_BB (PERIPH_BB_BASE + (RCC_CFGR_OFFSET * 32) + (RCC_MCO2EN_BIT_NUMBER * 4)) -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -#define PLL_TIMEOUT_VALUE ((uint32_t)2) /* 2 ms */ -/** - * @} - */ - -/** - * @} - */ - -/* Private macros ------------------------------------------------------------*/ -/** @defgroup RCCEx_Private_Macros RCCEx Private Macros - * @{ - */ -/** @defgroup RCCEx_IS_RCC_Definitions RCC Private macros to check input parameters - * @{ - */ -#if defined(STM32F411xE) -#define IS_RCC_PLLN_VALUE(VALUE) ((192U <= (VALUE)) && ((VALUE) <= 432U)) -#define IS_RCC_PLLI2SN_VALUE(VALUE) ((192U <= (VALUE)) && ((VALUE) <= 432U)) -#else /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || - STM32F429xx || STM32F439xx || STM32F401xC || STM32F401xE || STM32F410Tx || STM32F410Cx || - STM32F410Rx || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Cx || STM32F412Rx || - STM32F412Vx || STM32F412Zx */ -#define IS_RCC_PLLN_VALUE(VALUE) ((50U <= (VALUE)) && ((VALUE) <= 432U)) -#define IS_RCC_PLLI2SN_VALUE(VALUE) ((50U <= (VALUE)) && ((VALUE) <= 432U)) -#endif /* STM32F411xE */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) -#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x0000007FU)) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */ - -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx) -#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x00000007U)) -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx */ - -#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) -#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x0000000FU)) -#endif /* STM32F401xC || STM32F401xE || STM32F411xE */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x0000001FU)) -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -#if defined(STM32F446xx) -#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x00000FFFU)) -#endif /* STM32F446xx */ - -#if defined(STM32F469xx) || defined(STM32F479xx) -#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x000001FFU)) -#endif /* STM32F469xx || STM32F479xx */ - -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x000003FFU)) -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#define IS_RCC_PLLI2SR_VALUE(VALUE) ((2U <= (VALUE)) && ((VALUE) <= 7U)) - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) ||\ - defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) -#define IS_RCC_PLLI2SQ_VALUE(VALUE) ((2U <= (VALUE)) && ((VALUE) <= 15U)) - -#define IS_RCC_PLLSAIN_VALUE(VALUE) ((50U <= (VALUE)) && ((VALUE) <= 432U)) - -#define IS_RCC_PLLSAIQ_VALUE(VALUE) ((2U <= (VALUE)) && ((VALUE) <= 15U)) - -#define IS_RCC_PLLSAIR_VALUE(VALUE) ((2U <= (VALUE)) && ((VALUE) <= 7U)) - -#define IS_RCC_PLLSAI_DIVQ_VALUE(VALUE) ((1U <= (VALUE)) && ((VALUE) <= 32U)) - -#define IS_RCC_PLLI2S_DIVQ_VALUE(VALUE) ((1U <= (VALUE)) && ((VALUE) <= 32U)) - -#define IS_RCC_PLLSAI_DIVR_VALUE(VALUE) (((VALUE) == RCC_PLLSAIDIVR_2) ||\ - ((VALUE) == RCC_PLLSAIDIVR_4) ||\ - ((VALUE) == RCC_PLLSAIDIVR_8) ||\ - ((VALUE) == RCC_PLLSAIDIVR_16)) -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ - defined(STM32F412Rx) || defined(STM32F412Cx) -#define IS_RCC_PLLI2SM_VALUE(VALUE) ((VALUE) <= 63U) - -#define IS_RCC_LSE_MODE(MODE) (((MODE) == RCC_LSE_LOWPOWER_MODE) ||\ - ((MODE) == RCC_LSE_HIGHDRIVE_MODE)) -#endif /* STM32F411xE || STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -#define IS_RCC_PLLR_VALUE(VALUE) ((2U <= (VALUE)) && ((VALUE) <= 7U)) - -#define IS_RCC_LSE_MODE(MODE) (((MODE) == RCC_LSE_LOWPOWER_MODE) ||\ - ((MODE) == RCC_LSE_HIGHDRIVE_MODE)) - -#define IS_RCC_FMPI2C1CLKSOURCE(SOURCE) (((SOURCE) == RCC_FMPI2C1CLKSOURCE_APB) ||\ - ((SOURCE) == RCC_FMPI2C1CLKSOURCE_SYSCLK) ||\ - ((SOURCE) == RCC_FMPI2C1CLKSOURCE_HSI)) - -#define IS_RCC_LPTIM1CLKSOURCE(SOURCE) (((SOURCE) == RCC_LPTIM1CLKSOURCE_PCLK) ||\ - ((SOURCE) == RCC_LPTIM1CLKSOURCE_HSI) ||\ - ((SOURCE) == RCC_LPTIM1CLKSOURCE_LSI) ||\ - ((SOURCE) == RCC_LPTIM1CLKSOURCE_LSE)) - -#define IS_RCC_I2SAPBCLKSOURCE(SOURCE) (((SOURCE) == RCC_I2SAPBCLKSOURCE_PLLR) ||\ - ((SOURCE) == RCC_I2SAPBCLKSOURCE_EXT) ||\ - ((SOURCE) == RCC_I2SAPBCLKSOURCE_PLLSRC)) -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -#if defined(STM32F446xx) -#define IS_RCC_PLLR_VALUE(VALUE) ((2U <= (VALUE)) && ((VALUE) <= 7U)) - -#define IS_RCC_PLLI2SP_VALUE(VALUE) (((VALUE) == RCC_PLLI2SP_DIV2) ||\ - ((VALUE) == RCC_PLLI2SP_DIV4) ||\ - ((VALUE) == RCC_PLLI2SP_DIV6) ||\ - ((VALUE) == RCC_PLLI2SP_DIV8)) - -#define IS_RCC_PLLSAIM_VALUE(VALUE) ((VALUE) <= 63U) - -#define IS_RCC_PLLSAIP_VALUE(VALUE) (((VALUE) == RCC_PLLSAIP_DIV2) ||\ - ((VALUE) == RCC_PLLSAIP_DIV4) ||\ - ((VALUE) == RCC_PLLSAIP_DIV6) ||\ - ((VALUE) == RCC_PLLSAIP_DIV8)) - -#define IS_RCC_SAI1CLKSOURCE(SOURCE) (((SOURCE) == RCC_SAI1CLKSOURCE_PLLSAI) ||\ - ((SOURCE) == RCC_SAI1CLKSOURCE_PLLI2S) ||\ - ((SOURCE) == RCC_SAI1CLKSOURCE_PLLR) ||\ - ((SOURCE) == RCC_SAI1CLKSOURCE_EXT)) - -#define IS_RCC_SAI2CLKSOURCE(SOURCE) (((SOURCE) == RCC_SAI2CLKSOURCE_PLLSAI) ||\ - ((SOURCE) == RCC_SAI2CLKSOURCE_PLLI2S) ||\ - ((SOURCE) == RCC_SAI2CLKSOURCE_PLLR) ||\ - ((SOURCE) == RCC_SAI2CLKSOURCE_PLLSRC)) - -#define IS_RCC_I2SAPB1CLKSOURCE(SOURCE) (((SOURCE) == RCC_I2SAPB1CLKSOURCE_PLLI2S) ||\ - ((SOURCE) == RCC_I2SAPB1CLKSOURCE_EXT) ||\ - ((SOURCE) == RCC_I2SAPB1CLKSOURCE_PLLR) ||\ - ((SOURCE) == RCC_I2SAPB1CLKSOURCE_PLLSRC)) - -#define IS_RCC_I2SAPB2CLKSOURCE(SOURCE) (((SOURCE) == RCC_I2SAPB2CLKSOURCE_PLLI2S) ||\ - ((SOURCE) == RCC_I2SAPB2CLKSOURCE_EXT) ||\ - ((SOURCE) == RCC_I2SAPB2CLKSOURCE_PLLR) ||\ - ((SOURCE) == RCC_I2SAPB2CLKSOURCE_PLLSRC)) - -#define IS_RCC_FMPI2C1CLKSOURCE(SOURCE) (((SOURCE) == RCC_FMPI2C1CLKSOURCE_APB) ||\ - ((SOURCE) == RCC_FMPI2C1CLKSOURCE_SYSCLK) ||\ - ((SOURCE) == RCC_FMPI2C1CLKSOURCE_HSI)) - -#define IS_RCC_CECCLKSOURCE(SOURCE) (((SOURCE) == RCC_CECCLKSOURCE_HSI) ||\ - ((SOURCE) == RCC_CECCLKSOURCE_LSE)) - -#define IS_RCC_CLK48CLKSOURCE(SOURCE) (((SOURCE) == RCC_CLK48CLKSOURCE_PLLQ) ||\ - ((SOURCE) == RCC_CLK48CLKSOURCE_PLLSAIP)) - -#define IS_RCC_SDIOCLKSOURCE(SOURCE) (((SOURCE) == RCC_SDIOCLKSOURCE_CLK48) ||\ - ((SOURCE) == RCC_SDIOCLKSOURCE_SYSCLK)) - -#define IS_RCC_SPDIFRXCLKSOURCE(SOURCE) (((SOURCE) == RCC_SPDIFRXCLKSOURCE_PLLR) ||\ - ((SOURCE) == RCC_SPDIFRXCLKSOURCE_PLLI2SP)) -#endif /* STM32F446xx */ - -#if defined(STM32F469xx) || defined(STM32F479xx) -#define IS_RCC_PLLR_VALUE(VALUE) ((2U <= (VALUE)) && ((VALUE) <= 7U)) - -#define IS_RCC_PLLSAIP_VALUE(VALUE) (((VALUE) == RCC_PLLSAIP_DIV2) ||\ - ((VALUE) == RCC_PLLSAIP_DIV4) ||\ - ((VALUE) == RCC_PLLSAIP_DIV6) ||\ - ((VALUE) == RCC_PLLSAIP_DIV8)) - -#define IS_RCC_CLK48CLKSOURCE(SOURCE) (((SOURCE) == RCC_CLK48CLKSOURCE_PLLQ) ||\ - ((SOURCE) == RCC_CLK48CLKSOURCE_PLLSAIP)) - -#define IS_RCC_SDIOCLKSOURCE(SOURCE) (((SOURCE) == RCC_SDIOCLKSOURCE_CLK48) ||\ - ((SOURCE) == RCC_SDIOCLKSOURCE_SYSCLK)) - -#define IS_RCC_DSIBYTELANECLKSOURCE(SOURCE) (((SOURCE) == RCC_DSICLKSOURCE_PLLR) ||\ - ((SOURCE) == RCC_DSICLKSOURCE_DSIPHY)) - -#define IS_RCC_LSE_MODE(MODE) (((MODE) == RCC_LSE_LOWPOWER_MODE) ||\ - ((MODE) == RCC_LSE_HIGHDRIVE_MODE)) -#endif /* STM32F469xx || STM32F479xx */ - -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -#define IS_RCC_PLLR_VALUE(VALUE) ((2U <= (VALUE)) && ((VALUE) <= 7U)) - -#define IS_RCC_PLLI2SCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_PLLI2SCLKSOURCE_PLLSRC) || \ - ((__SOURCE__) == RCC_PLLI2SCLKSOURCE_EXT)) - -#define IS_RCC_I2SAPB1CLKSOURCE(SOURCE) (((SOURCE) == RCC_I2SAPB1CLKSOURCE_PLLI2S) ||\ - ((SOURCE) == RCC_I2SAPB1CLKSOURCE_EXT) ||\ - ((SOURCE) == RCC_I2SAPB1CLKSOURCE_PLLR) ||\ - ((SOURCE) == RCC_I2SAPB1CLKSOURCE_PLLSRC)) - -#define IS_RCC_I2SAPB2CLKSOURCE(SOURCE) (((SOURCE) == RCC_I2SAPB2CLKSOURCE_PLLI2S) ||\ - ((SOURCE) == RCC_I2SAPB2CLKSOURCE_EXT) ||\ - ((SOURCE) == RCC_I2SAPB2CLKSOURCE_PLLR) ||\ - ((SOURCE) == RCC_I2SAPB2CLKSOURCE_PLLSRC)) - -#define IS_RCC_FMPI2C1CLKSOURCE(SOURCE) (((SOURCE) == RCC_FMPI2C1CLKSOURCE_APB) ||\ - ((SOURCE) == RCC_FMPI2C1CLKSOURCE_SYSCLK) ||\ - ((SOURCE) == RCC_FMPI2C1CLKSOURCE_HSI)) - -#define IS_RCC_CLK48CLKSOURCE(SOURCE) (((SOURCE) == RCC_CLK48CLKSOURCE_PLLQ) ||\ - ((SOURCE) == RCC_CLK48CLKSOURCE_PLLI2SQ)) - -#define IS_RCC_SDIOCLKSOURCE(SOURCE) (((SOURCE) == RCC_SDIOCLKSOURCE_CLK48) ||\ - ((SOURCE) == RCC_SDIOCLKSOURCE_SYSCLK)) - -#define IS_RCC_DFSDM1CLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_DFSDM1CLKSOURCE_APB2) || \ - ((__SOURCE__) == RCC_DFSDM1CLKSOURCE_SYSCLK)) - -#define IS_RCC_DFSDM1AUDIOCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_DFSDM1AUDIOCLKSOURCE_I2SAPB1) || \ - ((__SOURCE__) == RCC_DFSDM1AUDIOCLKSOURCE_I2SAPB2)) - -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \ - defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \ - defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ - defined(STM32F412Rx) - -#define IS_RCC_MCO2SOURCE(SOURCE) (((SOURCE) == RCC_MCO2SOURCE_SYSCLK) || ((SOURCE) == RCC_MCO2SOURCE_PLLI2SCLK)|| \ - ((SOURCE) == RCC_MCO2SOURCE_HSE) || ((SOURCE) == RCC_MCO2SOURCE_PLLCLK)) - -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || - STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || \ - STM32F412Rx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -#define IS_RCC_MCO2SOURCE(SOURCE) (((SOURCE) == RCC_MCO2SOURCE_SYSCLK) || ((SOURCE) == RCC_MCO2SOURCE_I2SCLK)|| \ - ((SOURCE) == RCC_MCO2SOURCE_HSE) || ((SOURCE) == RCC_MCO2SOURCE_PLLCLK)) -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F4xx_HAL_RCC_EX_H */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_tim.h b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_tim.h deleted file mode 100644 index 7f234961..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_tim.h +++ /dev/null @@ -1,1610 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_tim.h - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Header file of TIM HAL module. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_TIM_H -#define __STM32F4xx_HAL_TIM_H - -#ifdef __cplusplus -extern "C" { -#endif - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_def.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @addtogroup TIM - * @{ - */ - -/* Exported types ------------------------------------------------------------*/ -/** @defgroup TIM_Exported_Types TIM Exported Types - * @{ - */ - -/** - * @brief TIM Time base Configuration Structure definition - */ -typedef struct -{ - uint32_t Prescaler; /*!< Specifies the prescaler value used to divide the TIM clock. - This parameter can be a number between Min_Data = 0x0000U and Max_Data = 0xFFFFU */ - - uint32_t CounterMode; /*!< Specifies the counter mode. - This parameter can be a value of @ref TIM_Counter_Mode */ - - uint32_t Period; /*!< Specifies the period value to be loaded into the active - Auto-Reload Register at the next update event. - This parameter can be a number between Min_Data = 0x0000U and Max_Data = 0xFFFF. */ - - uint32_t ClockDivision; /*!< Specifies the clock division. - This parameter can be a value of @ref TIM_ClockDivision */ - - uint32_t RepetitionCounter; /*!< Specifies the repetition counter value. Each time the RCR downcounter - reaches zero, an update event is generated and counting restarts - from the RCR value (N). - This means in PWM mode that (N+1) corresponds to: - - the number of PWM periods in edge-aligned mode - - the number of half PWM period in center-aligned mode - This parameter must be a number between Min_Data = 0x00 and Max_Data = 0xFF. - @note This parameter is valid only for TIM1 and TIM8. */ -} TIM_Base_InitTypeDef; - -/** - * @brief TIM Output Compare Configuration Structure definition - */ - -typedef struct -{ - uint32_t OCMode; /*!< Specifies the TIM mode. - This parameter can be a value of @ref TIM_Output_Compare_and_PWM_modes */ - - uint32_t Pulse; /*!< Specifies the pulse value to be loaded into the Capture Compare Register. - This parameter can be a number between Min_Data = 0x0000U and Max_Data = 0xFFFFU */ - - uint32_t OCPolarity; /*!< Specifies the output polarity. - This parameter can be a value of @ref TIM_Output_Compare_Polarity */ - - uint32_t OCNPolarity; /*!< Specifies the complementary output polarity. - This parameter can be a value of @ref TIM_Output_Compare_N_Polarity - @note This parameter is valid only for TIM1 and TIM8. */ - - uint32_t OCFastMode; /*!< Specifies the Fast mode state. - This parameter can be a value of @ref TIM_Output_Fast_State - @note This parameter is valid only in PWM1 and PWM2 mode. */ - - - uint32_t OCIdleState; /*!< Specifies the TIM Output Compare pin state during Idle state. - This parameter can be a value of @ref TIM_Output_Compare_Idle_State - @note This parameter is valid only for TIM1 and TIM8. */ - - uint32_t OCNIdleState; /*!< Specifies the TIM Output Compare pin state during Idle state. - This parameter can be a value of @ref TIM_Output_Compare_N_Idle_State - @note This parameter is valid only for TIM1 and TIM8. */ -} TIM_OC_InitTypeDef; - -/** - * @brief TIM One Pulse Mode Configuration Structure definition - */ -typedef struct -{ - uint32_t OCMode; /*!< Specifies the TIM mode. - This parameter can be a value of @ref TIM_Output_Compare_and_PWM_modes */ - - uint32_t Pulse; /*!< Specifies the pulse value to be loaded into the Capture Compare Register. - This parameter can be a number between Min_Data = 0x0000U and Max_Data = 0xFFFFU */ - - uint32_t OCPolarity; /*!< Specifies the output polarity. - This parameter can be a value of @ref TIM_Output_Compare_Polarity */ - - uint32_t OCNPolarity; /*!< Specifies the complementary output polarity. - This parameter can be a value of @ref TIM_Output_Compare_N_Polarity - @note This parameter is valid only for TIM1 and TIM8. */ - - uint32_t OCIdleState; /*!< Specifies the TIM Output Compare pin state during Idle state. - This parameter can be a value of @ref TIM_Output_Compare_Idle_State - @note This parameter is valid only for TIM1 and TIM8. */ - - uint32_t OCNIdleState; /*!< Specifies the TIM Output Compare pin state during Idle state. - This parameter can be a value of @ref TIM_Output_Compare_N_Idle_State - @note This parameter is valid only for TIM1 and TIM8. */ - - uint32_t ICPolarity; /*!< Specifies the active edge of the input signal. - This parameter can be a value of @ref TIM_Input_Capture_Polarity */ - - uint32_t ICSelection; /*!< Specifies the input. - This parameter can be a value of @ref TIM_Input_Capture_Selection */ - - uint32_t ICFilter; /*!< Specifies the input capture filter. - This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ -} TIM_OnePulse_InitTypeDef; - - -/** - * @brief TIM Input Capture Configuration Structure definition - */ - -typedef struct -{ - uint32_t ICPolarity; /*!< Specifies the active edge of the input signal. - This parameter can be a value of @ref TIM_Input_Capture_Polarity */ - - uint32_t ICSelection; /*!< Specifies the input. - This parameter can be a value of @ref TIM_Input_Capture_Selection */ - - uint32_t ICPrescaler; /*!< Specifies the Input Capture Prescaler. - This parameter can be a value of @ref TIM_Input_Capture_Prescaler */ - - uint32_t ICFilter; /*!< Specifies the input capture filter. - This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ -} TIM_IC_InitTypeDef; - -/** - * @brief TIM Encoder Configuration Structure definition - */ - -typedef struct -{ - uint32_t EncoderMode; /*!< Specifies the active edge of the input signal. - This parameter can be a value of @ref TIM_Encoder_Mode */ - - uint32_t IC1Polarity; /*!< Specifies the active edge of the input signal. - This parameter can be a value of @ref TIM_Input_Capture_Polarity */ - - uint32_t IC1Selection; /*!< Specifies the input. - This parameter can be a value of @ref TIM_Input_Capture_Selection */ - - uint32_t IC1Prescaler; /*!< Specifies the Input Capture Prescaler. - This parameter can be a value of @ref TIM_Input_Capture_Prescaler */ - - uint32_t IC1Filter; /*!< Specifies the input capture filter. - This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ - - uint32_t IC2Polarity; /*!< Specifies the active edge of the input signal. - This parameter can be a value of @ref TIM_Input_Capture_Polarity */ - - uint32_t IC2Selection; /*!< Specifies the input. - This parameter can be a value of @ref TIM_Input_Capture_Selection */ - - uint32_t IC2Prescaler; /*!< Specifies the Input Capture Prescaler. - This parameter can be a value of @ref TIM_Input_Capture_Prescaler */ - - uint32_t IC2Filter; /*!< Specifies the input capture filter. - This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ -} TIM_Encoder_InitTypeDef; - -/** - * @brief Clock Configuration Handle Structure definition - */ -typedef struct -{ - uint32_t ClockSource; /*!< TIM clock sources. - This parameter can be a value of @ref TIM_Clock_Source */ - uint32_t ClockPolarity; /*!< TIM clock polarity. - This parameter can be a value of @ref TIM_Clock_Polarity */ - uint32_t ClockPrescaler; /*!< TIM clock prescaler. - This parameter can be a value of @ref TIM_Clock_Prescaler */ - uint32_t ClockFilter; /*!< TIM clock filter. - This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ -} TIM_ClockConfigTypeDef; - -/** - * @brief Clear Input Configuration Handle Structure definition - */ -typedef struct -{ - uint32_t ClearInputState; /*!< TIM clear Input state. - This parameter can be ENABLE or DISABLE */ - uint32_t ClearInputSource; /*!< TIM clear Input sources. - This parameter can be a value of @ref TIM_ClearInput_Source */ - uint32_t ClearInputPolarity; /*!< TIM Clear Input polarity. - This parameter can be a value of @ref TIM_ClearInput_Polarity */ - uint32_t ClearInputPrescaler; /*!< TIM Clear Input prescaler. - This parameter can be a value of @ref TIM_ClearInput_Prescaler */ - uint32_t ClearInputFilter; /*!< TIM Clear Input filter. - This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ -} TIM_ClearInputConfigTypeDef; - -/** - * @brief TIM Slave configuration Structure definition - */ -typedef struct -{ - uint32_t SlaveMode; /*!< Slave mode selection - This parameter can be a value of @ref TIM_Slave_Mode */ - uint32_t InputTrigger; /*!< Input Trigger source - This parameter can be a value of @ref TIM_Trigger_Selection */ - uint32_t TriggerPolarity; /*!< Input Trigger polarity - This parameter can be a value of @ref TIM_Trigger_Polarity */ - uint32_t TriggerPrescaler; /*!< Input trigger prescaler - This parameter can be a value of @ref TIM_Trigger_Prescaler */ - uint32_t TriggerFilter; /*!< Input trigger filter - This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ - -} TIM_SlaveConfigTypeDef; - -/** - * @brief HAL State structures definition - */ -typedef enum -{ - HAL_TIM_STATE_RESET = 0x00U, /*!< Peripheral not yet initialized or disabled */ - HAL_TIM_STATE_READY = 0x01U, /*!< Peripheral Initialized and ready for use */ - HAL_TIM_STATE_BUSY = 0x02U, /*!< An internal process is ongoing */ - HAL_TIM_STATE_TIMEOUT = 0x03U, /*!< Timeout state */ - HAL_TIM_STATE_ERROR = 0x04U /*!< Reception process is ongoing */ -} HAL_TIM_StateTypeDef; - -/** - * @brief HAL Active channel structures definition - */ -typedef enum -{ - HAL_TIM_ACTIVE_CHANNEL_1 = 0x01U, /*!< The active channel is 1 */ - HAL_TIM_ACTIVE_CHANNEL_2 = 0x02U, /*!< The active channel is 2 */ - HAL_TIM_ACTIVE_CHANNEL_3 = 0x04U, /*!< The active channel is 3 */ - HAL_TIM_ACTIVE_CHANNEL_4 = 0x08U, /*!< The active channel is 4 */ - HAL_TIM_ACTIVE_CHANNEL_CLEARED = 0x00U /*!< All active channels cleared */ -} HAL_TIM_ActiveChannel; - -/** - * @brief TIM Time Base Handle Structure definition - */ -typedef struct -{ - TIM_TypeDef* Instance; /*!< Register base address */ - TIM_Base_InitTypeDef Init; /*!< TIM Time Base required parameters */ - HAL_TIM_ActiveChannel Channel; /*!< Active channel */ - DMA_HandleTypeDef* hdma[7]; /*!< DMA Handlers array - This array is accessed by a @ref DMA_Handle_index */ - HAL_LockTypeDef Lock; /*!< Locking object */ - __IO HAL_TIM_StateTypeDef State; /*!< TIM operation state */ -} TIM_HandleTypeDef; -/** - * @} - */ - -/* Exported constants --------------------------------------------------------*/ -/** @defgroup TIM_Exported_Constants TIM Exported Constants - * @{ - */ - -/** @defgroup TIM_Input_Channel_Polarity TIM Input Channel Polarity - * @{ - */ -#define TIM_INPUTCHANNELPOLARITY_RISING ((uint32_t)0x00000000U) /*!< Polarity for TIx source */ -#define TIM_INPUTCHANNELPOLARITY_FALLING (TIM_CCER_CC1P) /*!< Polarity for TIx source */ -#define TIM_INPUTCHANNELPOLARITY_BOTHEDGE (TIM_CCER_CC1P | TIM_CCER_CC1NP) /*!< Polarity for TIx source */ -/** - * @} - */ - -/** @defgroup TIM_ETR_Polarity TIM ETR Polarity - * @{ - */ -#define TIM_ETRPOLARITY_INVERTED (TIM_SMCR_ETP) /*!< Polarity for ETR source */ -#define TIM_ETRPOLARITY_NONINVERTED ((uint32_t)0x00000000U) /*!< Polarity for ETR source */ -/** - * @} - */ - -/** @defgroup TIM_ETR_Prescaler TIM ETR Prescaler - * @{ - */ -#define TIM_ETRPRESCALER_DIV1 ((uint32_t)0x00000000U) /*!< No prescaler is used */ -#define TIM_ETRPRESCALER_DIV2 (TIM_SMCR_ETPS_0) /*!< ETR input source is divided by 2 */ -#define TIM_ETRPRESCALER_DIV4 (TIM_SMCR_ETPS_1) /*!< ETR input source is divided by 4 */ -#define TIM_ETRPRESCALER_DIV8 (TIM_SMCR_ETPS) /*!< ETR input source is divided by 8 */ -/** - * @} - */ - -/** @defgroup TIM_Counter_Mode TIM Counter Mode - * @{ - */ -#define TIM_COUNTERMODE_UP ((uint32_t)0x00000000U) -#define TIM_COUNTERMODE_DOWN TIM_CR1_DIR -#define TIM_COUNTERMODE_CENTERALIGNED1 TIM_CR1_CMS_0 -#define TIM_COUNTERMODE_CENTERALIGNED2 TIM_CR1_CMS_1 -#define TIM_COUNTERMODE_CENTERALIGNED3 TIM_CR1_CMS -/** - * @} - */ - -/** @defgroup TIM_ClockDivision TIM Clock Division - * @{ - */ -#define TIM_CLOCKDIVISION_DIV1 ((uint32_t)0x00000000U) -#define TIM_CLOCKDIVISION_DIV2 (TIM_CR1_CKD_0) -#define TIM_CLOCKDIVISION_DIV4 (TIM_CR1_CKD_1) -/** - * @} - */ - -/** @defgroup TIM_Output_Compare_and_PWM_modes TIM Output Compare and PWM modes - * @{ - */ -#define TIM_OCMODE_TIMING ((uint32_t)0x00000000U) -#define TIM_OCMODE_ACTIVE (TIM_CCMR1_OC1M_0) -#define TIM_OCMODE_INACTIVE (TIM_CCMR1_OC1M_1) -#define TIM_OCMODE_TOGGLE (TIM_CCMR1_OC1M_0 | TIM_CCMR1_OC1M_1) -#define TIM_OCMODE_PWM1 (TIM_CCMR1_OC1M_1 | TIM_CCMR1_OC1M_2) -#define TIM_OCMODE_PWM2 (TIM_CCMR1_OC1M) -#define TIM_OCMODE_FORCED_ACTIVE (TIM_CCMR1_OC1M_0 | TIM_CCMR1_OC1M_2) -#define TIM_OCMODE_FORCED_INACTIVE (TIM_CCMR1_OC1M_2) - -/** - * @} - */ - -/** @defgroup TIM_Output_Fast_State TIM Output Fast State - * @{ - */ -#define TIM_OCFAST_DISABLE ((uint32_t)0x00000000U) -#define TIM_OCFAST_ENABLE (TIM_CCMR1_OC1FE) -/** - * @} - */ - -/** @defgroup TIM_Output_Compare_Polarity TIM Output Compare Polarity - * @{ - */ -#define TIM_OCPOLARITY_HIGH ((uint32_t)0x00000000U) -#define TIM_OCPOLARITY_LOW (TIM_CCER_CC1P) -/** - * @} - */ - -/** @defgroup TIM_Output_Compare_N_Polarity TIM Output CompareN Polarity - * @{ - */ -#define TIM_OCNPOLARITY_HIGH ((uint32_t)0x00000000U) -#define TIM_OCNPOLARITY_LOW (TIM_CCER_CC1NP) -/** - * @} - */ - -/** @defgroup TIM_Output_Compare_Idle_State TIM Output Compare Idle State - * @{ - */ -#define TIM_OCIDLESTATE_SET (TIM_CR2_OIS1) -#define TIM_OCIDLESTATE_RESET ((uint32_t)0x00000000U) -/** - * @} - */ - -/** @defgroup TIM_Output_Compare_N_Idle_State TIM Output Compare N Idle State - * @{ - */ -#define TIM_OCNIDLESTATE_SET (TIM_CR2_OIS1N) -#define TIM_OCNIDLESTATE_RESET ((uint32_t)0x00000000U) -/** - * @} - */ - -/** @defgroup TIM_Channel TIM Channel - * @{ - */ -#define TIM_CHANNEL_1 ((uint32_t)0x00000000U) -#define TIM_CHANNEL_2 ((uint32_t)0x00000004U) -#define TIM_CHANNEL_3 ((uint32_t)0x00000008U) -#define TIM_CHANNEL_4 ((uint32_t)0x0000000CU) -#define TIM_CHANNEL_ALL ((uint32_t)0x00000018U) - -/** - * @} - */ - -/** @defgroup TIM_Input_Capture_Polarity TIM Input Capture Polarity - * @{ - */ -#define TIM_ICPOLARITY_RISING TIM_INPUTCHANNELPOLARITY_RISING -#define TIM_ICPOLARITY_FALLING TIM_INPUTCHANNELPOLARITY_FALLING -#define TIM_ICPOLARITY_BOTHEDGE TIM_INPUTCHANNELPOLARITY_BOTHEDGE -/** - * @} - */ - -/** @defgroup TIM_Input_Capture_Selection TIM Input Capture Selection - * @{ - */ -#define TIM_ICSELECTION_DIRECTTI (TIM_CCMR1_CC1S_0) /*!< TIM Input 1, 2, 3 or 4 is selected to be - connected to IC1, IC2, IC3 or IC4, respectively */ -#define TIM_ICSELECTION_INDIRECTTI (TIM_CCMR1_CC1S_1) /*!< TIM Input 1, 2, 3 or 4 is selected to be - connected to IC2, IC1, IC4 or IC3, respectively */ -#define TIM_ICSELECTION_TRC (TIM_CCMR1_CC1S) /*!< TIM Input 1, 2, 3 or 4 is selected to be connected to TRC */ - -/** - * @} - */ - -/** @defgroup TIM_Input_Capture_Prescaler TIM Input Capture Prescaler - * @{ - */ -#define TIM_ICPSC_DIV1 ((uint32_t)0x00000000U) /*!< Capture performed each time an edge is detected on the capture input */ -#define TIM_ICPSC_DIV2 (TIM_CCMR1_IC1PSC_0) /*!< Capture performed once every 2 events */ -#define TIM_ICPSC_DIV4 (TIM_CCMR1_IC1PSC_1) /*!< Capture performed once every 4 events */ -#define TIM_ICPSC_DIV8 (TIM_CCMR1_IC1PSC) /*!< Capture performed once every 8 events */ -/** - * @} - */ - -/** @defgroup TIM_One_Pulse_Mode TIM One Pulse Mode - * @{ - */ -#define TIM_OPMODE_SINGLE (TIM_CR1_OPM) -#define TIM_OPMODE_REPETITIVE ((uint32_t)0x00000000U) -/** - * @} - */ - -/** @defgroup TIM_Encoder_Mode TIM Encoder Mode - * @{ - */ -#define TIM_ENCODERMODE_TI1 (TIM_SMCR_SMS_0) -#define TIM_ENCODERMODE_TI2 (TIM_SMCR_SMS_1) -#define TIM_ENCODERMODE_TI12 (TIM_SMCR_SMS_1 | TIM_SMCR_SMS_0) - -/** - * @} - */ - -/** @defgroup TIM_Interrupt_definition TIM Interrupt definition - * @{ - */ -#define TIM_IT_UPDATE (TIM_DIER_UIE) -#define TIM_IT_CC1 (TIM_DIER_CC1IE) -#define TIM_IT_CC2 (TIM_DIER_CC2IE) -#define TIM_IT_CC3 (TIM_DIER_CC3IE) -#define TIM_IT_CC4 (TIM_DIER_CC4IE) -#define TIM_IT_COM (TIM_DIER_COMIE) -#define TIM_IT_TRIGGER (TIM_DIER_TIE) -#define TIM_IT_BREAK (TIM_DIER_BIE) -/** - * @} - */ - -/** @defgroup TIM_Commutation_Source TIM Commutation Source - * @{ - */ -#define TIM_COMMUTATION_TRGI (TIM_CR2_CCUS) -#define TIM_COMMUTATION_SOFTWARE ((uint32_t)0x00000000U) -/** - * @} - */ - -/** @defgroup TIM_DMA_sources TIM DMA sources - * @{ - */ -#define TIM_DMA_UPDATE (TIM_DIER_UDE) -#define TIM_DMA_CC1 (TIM_DIER_CC1DE) -#define TIM_DMA_CC2 (TIM_DIER_CC2DE) -#define TIM_DMA_CC3 (TIM_DIER_CC3DE) -#define TIM_DMA_CC4 (TIM_DIER_CC4DE) -#define TIM_DMA_COM (TIM_DIER_COMDE) -#define TIM_DMA_TRIGGER (TIM_DIER_TDE) -/** - * @} - */ - -/** @defgroup TIM_Event_Source TIM Event Source - * @{ - */ -#define TIM_EVENTSOURCE_UPDATE TIM_EGR_UG -#define TIM_EVENTSOURCE_CC1 TIM_EGR_CC1G -#define TIM_EVENTSOURCE_CC2 TIM_EGR_CC2G -#define TIM_EVENTSOURCE_CC3 TIM_EGR_CC3G -#define TIM_EVENTSOURCE_CC4 TIM_EGR_CC4G -#define TIM_EVENTSOURCE_COM TIM_EGR_COMG -#define TIM_EVENTSOURCE_TRIGGER TIM_EGR_TG -#define TIM_EVENTSOURCE_BREAK TIM_EGR_BG - -/** - * @} - */ - -/** @defgroup TIM_Flag_definition TIM Flag definition - * @{ - */ -#define TIM_FLAG_UPDATE (TIM_SR_UIF) -#define TIM_FLAG_CC1 (TIM_SR_CC1IF) -#define TIM_FLAG_CC2 (TIM_SR_CC2IF) -#define TIM_FLAG_CC3 (TIM_SR_CC3IF) -#define TIM_FLAG_CC4 (TIM_SR_CC4IF) -#define TIM_FLAG_COM (TIM_SR_COMIF) -#define TIM_FLAG_TRIGGER (TIM_SR_TIF) -#define TIM_FLAG_BREAK (TIM_SR_BIF) -#define TIM_FLAG_CC1OF (TIM_SR_CC1OF) -#define TIM_FLAG_CC2OF (TIM_SR_CC2OF) -#define TIM_FLAG_CC3OF (TIM_SR_CC3OF) -#define TIM_FLAG_CC4OF (TIM_SR_CC4OF) -/** - * @} - */ - -/** @defgroup TIM_Clock_Source TIM Clock Source - * @{ - */ -#define TIM_CLOCKSOURCE_ETRMODE2 (TIM_SMCR_ETPS_1) -#define TIM_CLOCKSOURCE_INTERNAL (TIM_SMCR_ETPS_0) -#define TIM_CLOCKSOURCE_ITR0 ((uint32_t)0x00000000U) -#define TIM_CLOCKSOURCE_ITR1 (TIM_SMCR_TS_0) -#define TIM_CLOCKSOURCE_ITR2 (TIM_SMCR_TS_1) -#define TIM_CLOCKSOURCE_ITR3 (TIM_SMCR_TS_0 | TIM_SMCR_TS_1) -#define TIM_CLOCKSOURCE_TI1ED (TIM_SMCR_TS_2) -#define TIM_CLOCKSOURCE_TI1 (TIM_SMCR_TS_0 | TIM_SMCR_TS_2) -#define TIM_CLOCKSOURCE_TI2 (TIM_SMCR_TS_1 | TIM_SMCR_TS_2) -#define TIM_CLOCKSOURCE_ETRMODE1 (TIM_SMCR_TS) -/** - * @} - */ - -/** @defgroup TIM_Clock_Polarity TIM Clock Polarity - * @{ - */ -#define TIM_CLOCKPOLARITY_INVERTED TIM_ETRPOLARITY_INVERTED /*!< Polarity for ETRx clock sources */ -#define TIM_CLOCKPOLARITY_NONINVERTED TIM_ETRPOLARITY_NONINVERTED /*!< Polarity for ETRx clock sources */ -#define TIM_CLOCKPOLARITY_RISING TIM_INPUTCHANNELPOLARITY_RISING /*!< Polarity for TIx clock sources */ -#define TIM_CLOCKPOLARITY_FALLING TIM_INPUTCHANNELPOLARITY_FALLING /*!< Polarity for TIx clock sources */ -#define TIM_CLOCKPOLARITY_BOTHEDGE TIM_INPUTCHANNELPOLARITY_BOTHEDGE /*!< Polarity for TIx clock sources */ -/** - * @} - */ - -/** @defgroup TIM_Clock_Prescaler TIM Clock Prescaler - * @{ - */ -#define TIM_CLOCKPRESCALER_DIV1 TIM_ETRPRESCALER_DIV1 /*!< No prescaler is used */ -#define TIM_CLOCKPRESCALER_DIV2 TIM_ETRPRESCALER_DIV2 /*!< Prescaler for External ETR Clock: Capture performed once every 2 events. */ -#define TIM_CLOCKPRESCALER_DIV4 TIM_ETRPRESCALER_DIV4 /*!< Prescaler for External ETR Clock: Capture performed once every 4 events. */ -#define TIM_CLOCKPRESCALER_DIV8 TIM_ETRPRESCALER_DIV8 /*!< Prescaler for External ETR Clock: Capture performed once every 8 events. */ -/** - * @} - */ - -/** @defgroup TIM_ClearInput_Source TIM Clear Input Source - * @{ - */ -#define TIM_CLEARINPUTSOURCE_ETR ((uint32_t)0x00000001U) -#define TIM_CLEARINPUTSOURCE_NONE ((uint32_t)0x00000000U) -/** - * @} - */ - -/** @defgroup TIM_ClearInput_Polarity TIM Clear Input Polarity - * @{ - */ -#define TIM_CLEARINPUTPOLARITY_INVERTED TIM_ETRPOLARITY_INVERTED /*!< Polarity for ETRx pin */ -#define TIM_CLEARINPUTPOLARITY_NONINVERTED TIM_ETRPOLARITY_NONINVERTED /*!< Polarity for ETRx pin */ -/** - * @} - */ - -/** @defgroup TIM_ClearInput_Prescaler TIM Clear Input Prescaler - * @{ - */ -#define TIM_CLEARINPUTPRESCALER_DIV1 TIM_ETRPRESCALER_DIV1 /*!< No prescaler is used */ -#define TIM_CLEARINPUTPRESCALER_DIV2 TIM_ETRPRESCALER_DIV2 /*!< Prescaler for External ETR pin: Capture performed once every 2 events. */ -#define TIM_CLEARINPUTPRESCALER_DIV4 TIM_ETRPRESCALER_DIV4 /*!< Prescaler for External ETR pin: Capture performed once every 4 events. */ -#define TIM_CLEARINPUTPRESCALER_DIV8 TIM_ETRPRESCALER_DIV8 /*!< Prescaler for External ETR pin: Capture performed once every 8 events. */ -/** - * @} - */ - -/** @defgroup TIM_OSSR_Off_State_Selection_for_Run_mode_state TIM OSSR OffState Selection for Run mode state - * @{ - */ -#define TIM_OSSR_ENABLE (TIM_BDTR_OSSR) -#define TIM_OSSR_DISABLE ((uint32_t)0x00000000U) -/** - * @} - */ - -/** @defgroup TIM_OSSI_Off_State_Selection_for_Idle_mode_state TIM OSSI OffState Selection for Idle mode state - * @{ - */ -#define TIM_OSSI_ENABLE (TIM_BDTR_OSSI) -#define TIM_OSSI_DISABLE ((uint32_t)0x00000000U) -/** - * @} - */ - -/** @defgroup TIM_Lock_level TIM Lock level - * @{ - */ -#define TIM_LOCKLEVEL_OFF ((uint32_t)0x00000000U) -#define TIM_LOCKLEVEL_1 (TIM_BDTR_LOCK_0) -#define TIM_LOCKLEVEL_2 (TIM_BDTR_LOCK_1) -#define TIM_LOCKLEVEL_3 (TIM_BDTR_LOCK) -/** - * @} - */ -/** @defgroup TIM_Break_Input_enable_disable TIM Break Input State - * @{ - */ -#define TIM_BREAK_ENABLE (TIM_BDTR_BKE) -#define TIM_BREAK_DISABLE ((uint32_t)0x00000000U) -/** - * @} - */ - -/** @defgroup TIM_Break_Polarity TIM Break Polarity - * @{ - */ -#define TIM_BREAKPOLARITY_LOW ((uint32_t)0x00000000U) -#define TIM_BREAKPOLARITY_HIGH (TIM_BDTR_BKP) -/** - * @} - */ - -/** @defgroup TIM_AOE_Bit_Set_Reset TIM AOE Bit State - * @{ - */ -#define TIM_AUTOMATICOUTPUT_ENABLE (TIM_BDTR_AOE) -#define TIM_AUTOMATICOUTPUT_DISABLE ((uint32_t)0x00000000U) -/** - * @} - */ - -/** @defgroup TIM_Master_Mode_Selection TIM Master Mode Selection - * @{ - */ -#define TIM_TRGO_RESET ((uint32_t)0x00000000U) -#define TIM_TRGO_ENABLE (TIM_CR2_MMS_0) -#define TIM_TRGO_UPDATE (TIM_CR2_MMS_1) -#define TIM_TRGO_OC1 ((TIM_CR2_MMS_1 | TIM_CR2_MMS_0)) -#define TIM_TRGO_OC1REF (TIM_CR2_MMS_2) -#define TIM_TRGO_OC2REF ((TIM_CR2_MMS_2 | TIM_CR2_MMS_0)) -#define TIM_TRGO_OC3REF ((TIM_CR2_MMS_2 | TIM_CR2_MMS_1)) -#define TIM_TRGO_OC4REF ((TIM_CR2_MMS_2 | TIM_CR2_MMS_1 | TIM_CR2_MMS_0)) -/** - * @} - */ - -/** @defgroup TIM_Slave_Mode TIM Slave Mode - * @{ - */ -#define TIM_SLAVEMODE_DISABLE ((uint32_t)0x00000000U) -#define TIM_SLAVEMODE_RESET ((uint32_t)0x00000004U) -#define TIM_SLAVEMODE_GATED ((uint32_t)0x00000005U) -#define TIM_SLAVEMODE_TRIGGER ((uint32_t)0x00000006U) -#define TIM_SLAVEMODE_EXTERNAL1 ((uint32_t)0x00000007U) -/** - * @} - */ - -/** @defgroup TIM_Master_Slave_Mode TIM Master Slave Mode - * @{ - */ -#define TIM_MASTERSLAVEMODE_ENABLE ((uint32_t)0x00000080U) -#define TIM_MASTERSLAVEMODE_DISABLE ((uint32_t)0x00000000U) -/** - * @} - */ - -/** @defgroup TIM_Trigger_Selection TIM Trigger Selection - * @{ - */ -#define TIM_TS_ITR0 ((uint32_t)0x00000000U) -#define TIM_TS_ITR1 ((uint32_t)0x00000010U) -#define TIM_TS_ITR2 ((uint32_t)0x00000020U) -#define TIM_TS_ITR3 ((uint32_t)0x00000030U) -#define TIM_TS_TI1F_ED ((uint32_t)0x00000040U) -#define TIM_TS_TI1FP1 ((uint32_t)0x00000050U) -#define TIM_TS_TI2FP2 ((uint32_t)0x00000060U) -#define TIM_TS_ETRF ((uint32_t)0x00000070U) -#define TIM_TS_NONE ((uint32_t)0x0000FFFFU) -/** - * @} - */ - -/** @defgroup TIM_Trigger_Polarity TIM Trigger Polarity - * @{ - */ -#define TIM_TRIGGERPOLARITY_INVERTED TIM_ETRPOLARITY_INVERTED /*!< Polarity for ETRx trigger sources */ -#define TIM_TRIGGERPOLARITY_NONINVERTED TIM_ETRPOLARITY_NONINVERTED /*!< Polarity for ETRx trigger sources */ -#define TIM_TRIGGERPOLARITY_RISING TIM_INPUTCHANNELPOLARITY_RISING /*!< Polarity for TIxFPx or TI1_ED trigger sources */ -#define TIM_TRIGGERPOLARITY_FALLING TIM_INPUTCHANNELPOLARITY_FALLING /*!< Polarity for TIxFPx or TI1_ED trigger sources */ -#define TIM_TRIGGERPOLARITY_BOTHEDGE TIM_INPUTCHANNELPOLARITY_BOTHEDGE /*!< Polarity for TIxFPx or TI1_ED trigger sources */ -/** - * @} - */ - -/** @defgroup TIM_Trigger_Prescaler TIM Trigger Prescaler - * @{ - */ -#define TIM_TRIGGERPRESCALER_DIV1 TIM_ETRPRESCALER_DIV1 /*!< No prescaler is used */ -#define TIM_TRIGGERPRESCALER_DIV2 TIM_ETRPRESCALER_DIV2 /*!< Prescaler for External ETR Trigger: Capture performed once every 2 events. */ -#define TIM_TRIGGERPRESCALER_DIV4 TIM_ETRPRESCALER_DIV4 /*!< Prescaler for External ETR Trigger: Capture performed once every 4 events. */ -#define TIM_TRIGGERPRESCALER_DIV8 TIM_ETRPRESCALER_DIV8 /*!< Prescaler for External ETR Trigger: Capture performed once every 8 events. */ -/** - * @} - */ - - -/** @defgroup TIM_TI1_Selection TIM TI1 Selection - * @{ - */ -#define TIM_TI1SELECTION_CH1 ((uint32_t)0x00000000U) -#define TIM_TI1SELECTION_XORCOMBINATION (TIM_CR2_TI1S) -/** - * @} - */ - -/** @defgroup TIM_DMA_Base_address TIM DMA Base address - * @{ - */ -#define TIM_DMABASE_CR1 (0x00000000U) -#define TIM_DMABASE_CR2 (0x00000001U) -#define TIM_DMABASE_SMCR (0x00000002U) -#define TIM_DMABASE_DIER (0x00000003U) -#define TIM_DMABASE_SR (0x00000004U) -#define TIM_DMABASE_EGR (0x00000005U) -#define TIM_DMABASE_CCMR1 (0x00000006U) -#define TIM_DMABASE_CCMR2 (0x00000007U) -#define TIM_DMABASE_CCER (0x00000008U) -#define TIM_DMABASE_CNT (0x00000009U) -#define TIM_DMABASE_PSC (0x0000000AU) -#define TIM_DMABASE_ARR (0x0000000BU) -#define TIM_DMABASE_RCR (0x0000000CU) -#define TIM_DMABASE_CCR1 (0x0000000DU) -#define TIM_DMABASE_CCR2 (0x0000000EU) -#define TIM_DMABASE_CCR3 (0x0000000FU) -#define TIM_DMABASE_CCR4 (0x00000010U) -#define TIM_DMABASE_BDTR (0x00000011U) -#define TIM_DMABASE_DCR (0x00000012U) -#define TIM_DMABASE_OR (0x00000013U) -/** - * @} - */ - -/** @defgroup TIM_DMA_Burst_Length TIM DMA Burst Length - * @{ - */ -#define TIM_DMABURSTLENGTH_1TRANSFER (0x00000000U) -#define TIM_DMABURSTLENGTH_2TRANSFERS (0x00000100U) -#define TIM_DMABURSTLENGTH_3TRANSFERS (0x00000200U) -#define TIM_DMABURSTLENGTH_4TRANSFERS (0x00000300U) -#define TIM_DMABURSTLENGTH_5TRANSFERS (0x00000400U) -#define TIM_DMABURSTLENGTH_6TRANSFERS (0x00000500U) -#define TIM_DMABURSTLENGTH_7TRANSFERS (0x00000600U) -#define TIM_DMABURSTLENGTH_8TRANSFERS (0x00000700U) -#define TIM_DMABURSTLENGTH_9TRANSFERS (0x00000800U) -#define TIM_DMABURSTLENGTH_10TRANSFERS (0x00000900U) -#define TIM_DMABURSTLENGTH_11TRANSFERS (0x00000A00U) -#define TIM_DMABURSTLENGTH_12TRANSFERS (0x00000B00U) -#define TIM_DMABURSTLENGTH_13TRANSFERS (0x00000C00U) -#define TIM_DMABURSTLENGTH_14TRANSFERS (0x00000D00U) -#define TIM_DMABURSTLENGTH_15TRANSFERS (0x00000E00U) -#define TIM_DMABURSTLENGTH_16TRANSFERS (0x00000F00U) -#define TIM_DMABURSTLENGTH_17TRANSFERS (0x00001000U) -#define TIM_DMABURSTLENGTH_18TRANSFERS (0x00001100U) -/** - * @} - */ - -/** @defgroup DMA_Handle_index DMA Handle index - * @{ - */ -#define TIM_DMA_ID_UPDATE ((uint16_t) 0x0000U) /*!< Index of the DMA handle used for Update DMA requests */ -#define TIM_DMA_ID_CC1 ((uint16_t) 0x0001U) /*!< Index of the DMA handle used for Capture/Compare 1 DMA requests */ -#define TIM_DMA_ID_CC2 ((uint16_t) 0x0002U) /*!< Index of the DMA handle used for Capture/Compare 2 DMA requests */ -#define TIM_DMA_ID_CC3 ((uint16_t) 0x0003U) /*!< Index of the DMA handle used for Capture/Compare 3 DMA requests */ -#define TIM_DMA_ID_CC4 ((uint16_t) 0x0004U) /*!< Index of the DMA handle used for Capture/Compare 4 DMA requests */ -#define TIM_DMA_ID_COMMUTATION ((uint16_t) 0x0005U) /*!< Index of the DMA handle used for Commutation DMA requests */ -#define TIM_DMA_ID_TRIGGER ((uint16_t) 0x0006U) /*!< Index of the DMA handle used for Trigger DMA requests */ -/** - * @} - */ - -/** @defgroup Channel_CC_State Channel CC State - * @{ - */ -#define TIM_CCx_ENABLE ((uint32_t)0x00000001U) -#define TIM_CCx_DISABLE ((uint32_t)0x00000000U) -#define TIM_CCxN_ENABLE ((uint32_t)0x00000004U) -#define TIM_CCxN_DISABLE ((uint32_t)0x00000000U) -/** - * @} - */ - -/** - * @} - */ - -/* Exported macro ------------------------------------------------------------*/ -/** @defgroup TIM_Exported_Macros TIM Exported Macros - * @{ - */ -/** @brief Reset TIM handle state - * @param __HANDLE__: TIM handle - * @retval None - */ -#define __HAL_TIM_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_TIM_STATE_RESET) - -/** - * @brief Enable the TIM peripheral. - * @param __HANDLE__: TIM handle - * @retval None - */ -#define __HAL_TIM_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1|=(TIM_CR1_CEN)) - -/** - * @brief Enable the TIM main Output. - * @param __HANDLE__: TIM handle - * @retval None - */ -#define __HAL_TIM_MOE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->BDTR|=(TIM_BDTR_MOE)) - - -/** - * @brief Disable the TIM peripheral. - * @param __HANDLE__: TIM handle - * @retval None - */ -#define __HAL_TIM_DISABLE(__HANDLE__) \ - do { \ - if (((__HANDLE__)->Instance->CCER & TIM_CCER_CCxE_MASK) == 0U) \ - { \ - if(((__HANDLE__)->Instance->CCER & TIM_CCER_CCxNE_MASK) == 0U) \ - { \ - (__HANDLE__)->Instance->CR1 &= ~(TIM_CR1_CEN); \ - } \ - } \ - } while(0) - -/* The Main Output of a timer instance is disabled only if all the CCx and CCxN - channels have been disabled */ -/** - * @brief Disable the TIM main Output. - * @param __HANDLE__: TIM handle - * @retval None - */ -#define __HAL_TIM_MOE_DISABLE(__HANDLE__) \ - do { \ - if (((__HANDLE__)->Instance->CCER & TIM_CCER_CCxE_MASK) == 0U) \ - { \ - if(((__HANDLE__)->Instance->CCER & TIM_CCER_CCxNE_MASK) == 0U) \ - { \ - (__HANDLE__)->Instance->BDTR &= ~(TIM_BDTR_MOE); \ - } \ - } \ - } while(0) - -#define __HAL_TIM_ENABLE_IT(__HANDLE__, __INTERRUPT__) ((__HANDLE__)->Instance->DIER |= (__INTERRUPT__)) -#define __HAL_TIM_ENABLE_DMA(__HANDLE__, __DMA__) ((__HANDLE__)->Instance->DIER |= (__DMA__)) -#define __HAL_TIM_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((__HANDLE__)->Instance->DIER &= ~(__INTERRUPT__)) -#define __HAL_TIM_DISABLE_DMA(__HANDLE__, __DMA__) ((__HANDLE__)->Instance->DIER &= ~(__DMA__)) -#define __HAL_TIM_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR &(__FLAG__)) == (__FLAG__)) -#define __HAL_TIM_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->SR = ~(__FLAG__)) - -#define __HAL_TIM_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->DIER & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET) -#define __HAL_TIM_CLEAR_IT(__HANDLE__, __INTERRUPT__) ((__HANDLE__)->Instance->SR = ~(__INTERRUPT__)) - -#define __HAL_TIM_IS_TIM_COUNTING_DOWN(__HANDLE__) (((__HANDLE__)->Instance->CR1 &(TIM_CR1_DIR)) == (TIM_CR1_DIR)) -#define __HAL_TIM_SET_PRESCALER(__HANDLE__, __PRESC__) ((__HANDLE__)->Instance->PSC = (__PRESC__)) - -#define TIM_SET_ICPRESCALERVALUE(__HANDLE__, __CHANNEL__, __ICPSC__) \ -(((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCMR1 |= (__ICPSC__)) :\ - ((__CHANNEL__) == TIM_CHANNEL_2) ? ((__HANDLE__)->Instance->CCMR1 |= ((__ICPSC__) << 8U)) :\ - ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCMR2 |= (__ICPSC__)) :\ - ((__HANDLE__)->Instance->CCMR2 |= ((__ICPSC__) << 8U))) - -#define TIM_RESET_ICPRESCALERVALUE(__HANDLE__, __CHANNEL__) \ -(((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCMR1 &= (uint16_t)~TIM_CCMR1_IC1PSC) :\ - ((__CHANNEL__) == TIM_CHANNEL_2) ? ((__HANDLE__)->Instance->CCMR1 &= (uint16_t)~TIM_CCMR1_IC2PSC) :\ - ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCMR2 &= (uint16_t)~TIM_CCMR2_IC3PSC) :\ - ((__HANDLE__)->Instance->CCMR2 &= (uint16_t)~TIM_CCMR2_IC4PSC)) - -#define TIM_SET_CAPTUREPOLARITY(__HANDLE__, __CHANNEL__, __POLARITY__) \ -(((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCER |= (__POLARITY__)) :\ - ((__CHANNEL__) == TIM_CHANNEL_2) ? ((__HANDLE__)->Instance->CCER |= ((__POLARITY__) << 4U)) :\ - ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCER |= ((__POLARITY__) << 8U)) :\ - ((__HANDLE__)->Instance->CCER |= (((__POLARITY__) << 12U) & TIM_CCER_CC4P))) - -#define TIM_RESET_CAPTUREPOLARITY(__HANDLE__, __CHANNEL__) \ -(((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCER &= (uint16_t)~(TIM_CCER_CC1P | TIM_CCER_CC1NP)) :\ - ((__CHANNEL__) == TIM_CHANNEL_2) ? ((__HANDLE__)->Instance->CCER &= (uint16_t)~(TIM_CCER_CC2P | TIM_CCER_CC2NP)) :\ - ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCER &= (uint16_t)~(TIM_CCER_CC3P | TIM_CCER_CC3NP)) :\ - ((__HANDLE__)->Instance->CCER &= (uint16_t)~TIM_CCER_CC4P)) - -/** - * @brief Sets the TIM Capture Compare Register value on runtime without - * calling another time ConfigChannel function. - * @param __HANDLE__: TIM handle. - * @param __CHANNEL__ : TIM Channels to be configured. - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected - * @param __COMPARE__: specifies the Capture Compare register new value. - * @retval None - */ -#define __HAL_TIM_SET_COMPARE(__HANDLE__, __CHANNEL__, __COMPARE__) \ -(*(__IO uint32_t *)(&((__HANDLE__)->Instance->CCR1) + ((__CHANNEL__) >> 2U)) = (__COMPARE__)) - -/** - * @brief Gets the TIM Capture Compare Register value on runtime - * @param __HANDLE__: TIM handle. - * @param __CHANNEL__ : TIM Channel associated with the capture compare register - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: get capture/compare 1 register value - * @arg TIM_CHANNEL_2: get capture/compare 2 register value - * @arg TIM_CHANNEL_3: get capture/compare 3 register value - * @arg TIM_CHANNEL_4: get capture/compare 4 register value - * @retval None - */ -#define __HAL_TIM_GET_COMPARE(__HANDLE__, __CHANNEL__) \ - (*(__IO uint32_t *)(&((__HANDLE__)->Instance->CCR1) + ((__CHANNEL__) >> 2U))) - -/** - * @brief Sets the TIM Counter Register value on runtime. - * @param __HANDLE__: TIM handle. - * @param __COUNTER__: specifies the Counter register new value. - * @retval None - */ -#define __HAL_TIM_SET_COUNTER(__HANDLE__, __COUNTER__) ((__HANDLE__)->Instance->CNT = (__COUNTER__)) - -/** - * @brief Gets the TIM Counter Register value on runtime. - * @param __HANDLE__: TIM handle. - * @retval None - */ -#define __HAL_TIM_GET_COUNTER(__HANDLE__) ((__HANDLE__)->Instance->CNT) - -/** - * @brief Sets the TIM Autoreload Register value on runtime without calling - * another time any Init function. - * @param __HANDLE__: TIM handle. - * @param __AUTORELOAD__: specifies the Counter register new value. - * @retval None - */ -#define __HAL_TIM_SET_AUTORELOAD(__HANDLE__, __AUTORELOAD__) \ - do{ \ - (__HANDLE__)->Instance->ARR = (__AUTORELOAD__); \ - (__HANDLE__)->Init.Period = (__AUTORELOAD__); \ - } while(0) -/** - * @brief Gets the TIM Autoreload Register value on runtime - * @param __HANDLE__: TIM handle. - * @retval None - */ -#define __HAL_TIM_GET_AUTORELOAD(__HANDLE__) ((__HANDLE__)->Instance->ARR) - -/** - * @brief Sets the TIM Clock Division value on runtime without calling - * another time any Init function. - * @param __HANDLE__: TIM handle. - * @param __CKD__: specifies the clock division value. - * This parameter can be one of the following value: - * @arg TIM_CLOCKDIVISION_DIV1 - * @arg TIM_CLOCKDIVISION_DIV2 - * @arg TIM_CLOCKDIVISION_DIV4 - * @retval None - */ -#define __HAL_TIM_SET_CLOCKDIVISION(__HANDLE__, __CKD__) \ - do{ \ - (__HANDLE__)->Instance->CR1 &= (uint16_t)(~TIM_CR1_CKD); \ - (__HANDLE__)->Instance->CR1 |= (__CKD__); \ - (__HANDLE__)->Init.ClockDivision = (__CKD__); \ - } while(0) -/** - * @brief Gets the TIM Clock Division value on runtime - * @param __HANDLE__: TIM handle. - * @retval None - */ -#define __HAL_TIM_GET_CLOCKDIVISION(__HANDLE__) ((__HANDLE__)->Instance->CR1 & TIM_CR1_CKD) - -/** - * @brief Sets the TIM Input Capture prescaler on runtime without calling - * another time HAL_TIM_IC_ConfigChannel() function. - * @param __HANDLE__: TIM handle. - * @param __CHANNEL__ : TIM Channels to be configured. - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected - * @param __ICPSC__: specifies the Input Capture4 prescaler new value. - * This parameter can be one of the following values: - * @arg TIM_ICPSC_DIV1: no prescaler - * @arg TIM_ICPSC_DIV2: capture is done once every 2 events - * @arg TIM_ICPSC_DIV4: capture is done once every 4 events - * @arg TIM_ICPSC_DIV8: capture is done once every 8 events - * @retval None - */ -#define __HAL_TIM_SET_ICPRESCALER(__HANDLE__, __CHANNEL__, __ICPSC__) \ - do{ \ - TIM_RESET_ICPRESCALERVALUE((__HANDLE__), (__CHANNEL__)); \ - TIM_SET_ICPRESCALERVALUE((__HANDLE__), (__CHANNEL__), (__ICPSC__)); \ - } while(0) - -/** - * @brief Gets the TIM Input Capture prescaler on runtime - * @param __HANDLE__: TIM handle. - * @param __CHANNEL__ : TIM Channels to be configured. - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: get input capture 1 prescaler value - * @arg TIM_CHANNEL_2: get input capture 2 prescaler value - * @arg TIM_CHANNEL_3: get input capture 3 prescaler value - * @arg TIM_CHANNEL_4: get input capture 4 prescaler value - * @retval None - */ -#define __HAL_TIM_GET_ICPRESCALER(__HANDLE__, __CHANNEL__) \ - (((__CHANNEL__) == TIM_CHANNEL_1) ? ((__HANDLE__)->Instance->CCMR1 & TIM_CCMR1_IC1PSC) :\ - ((__CHANNEL__) == TIM_CHANNEL_2) ? (((__HANDLE__)->Instance->CCMR1 & TIM_CCMR1_IC2PSC) >> 8U) :\ - ((__CHANNEL__) == TIM_CHANNEL_3) ? ((__HANDLE__)->Instance->CCMR2 & TIM_CCMR2_IC3PSC) :\ - (((__HANDLE__)->Instance->CCMR2 & TIM_CCMR2_IC4PSC)) >> 8U) - -/** - * @brief Set the Update Request Source (URS) bit of the TIMx_CR1 register - * @param __HANDLE__: TIM handle. - * @note When the USR bit of the TIMx_CR1 register is set, only counter - * overflow/underflow generates an update interrupt or DMA request (if - * enabled) - * @retval None - */ -#define __HAL_TIM_URS_ENABLE(__HANDLE__) \ - ((__HANDLE__)->Instance->CR1|= (TIM_CR1_URS)) - -/** - * @brief Reset the Update Request Source (URS) bit of the TIMx_CR1 register - * @param __HANDLE__: TIM handle. - * @note When the USR bit of the TIMx_CR1 register is reset, any of the - * following events generate an update interrupt or DMA request (if - * enabled): - * _ Counter overflow/underflow - * _ Setting the UG bit - * _ Update generation through the slave mode controller - * @retval None - */ -#define __HAL_TIM_URS_DISABLE(__HANDLE__) \ - ((__HANDLE__)->Instance->CR1&=~(TIM_CR1_URS)) - -/** - * @brief Sets the TIM Capture x input polarity on runtime. - * @param __HANDLE__: TIM handle. - * @param __CHANNEL__: TIM Channels to be configured. - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @arg TIM_CHANNEL_4: TIM Channel 4 selected - * @param __POLARITY__: Polarity for TIx source - * @arg TIM_INPUTCHANNELPOLARITY_RISING: Rising Edge - * @arg TIM_INPUTCHANNELPOLARITY_FALLING: Falling Edge - * @arg TIM_INPUTCHANNELPOLARITY_BOTHEDGE: Rising and Falling Edge - * @note The polarity TIM_INPUTCHANNELPOLARITY_BOTHEDGE is not authorized for TIM Channel 4. - * @retval None - */ -#define __HAL_TIM_SET_CAPTUREPOLARITY(__HANDLE__, __CHANNEL__, __POLARITY__) \ - do{ \ - TIM_RESET_CAPTUREPOLARITY((__HANDLE__), (__CHANNEL__)); \ - TIM_SET_CAPTUREPOLARITY((__HANDLE__), (__CHANNEL__), (__POLARITY__)); \ - }while(0) -/** - * @} - */ - -/* Include TIM HAL Extension module */ -#include "stm32f4xx_hal_tim_ex.h" - -/* Exported functions --------------------------------------------------------*/ -/** @addtogroup TIM_Exported_Functions - * @{ - */ - -/** @addtogroup TIM_Exported_Functions_Group1 - * @{ - */ - -/* Time Base functions ********************************************************/ -HAL_StatusTypeDef HAL_TIM_Base_Init(TIM_HandleTypeDef* htim); -HAL_StatusTypeDef HAL_TIM_Base_DeInit(TIM_HandleTypeDef* htim); -void HAL_TIM_Base_MspInit(TIM_HandleTypeDef* htim); -void HAL_TIM_Base_MspDeInit(TIM_HandleTypeDef* htim); -/* Blocking mode: Polling */ -HAL_StatusTypeDef HAL_TIM_Base_Start(TIM_HandleTypeDef* htim); -HAL_StatusTypeDef HAL_TIM_Base_Stop(TIM_HandleTypeDef* htim); -/* Non-Blocking mode: Interrupt */ -HAL_StatusTypeDef HAL_TIM_Base_Start_IT(TIM_HandleTypeDef* htim); -HAL_StatusTypeDef HAL_TIM_Base_Stop_IT(TIM_HandleTypeDef* htim); -/* Non-Blocking mode: DMA */ -HAL_StatusTypeDef HAL_TIM_Base_Start_DMA(TIM_HandleTypeDef* htim, uint32_t* pData, uint16_t Length); -HAL_StatusTypeDef HAL_TIM_Base_Stop_DMA(TIM_HandleTypeDef* htim); -/** - * @} - */ - -/** @addtogroup TIM_Exported_Functions_Group2 - * @{ - */ -/* Timer Output Compare functions **********************************************/ -HAL_StatusTypeDef HAL_TIM_OC_Init(TIM_HandleTypeDef* htim); -HAL_StatusTypeDef HAL_TIM_OC_DeInit(TIM_HandleTypeDef* htim); -void HAL_TIM_OC_MspInit(TIM_HandleTypeDef* htim); -void HAL_TIM_OC_MspDeInit(TIM_HandleTypeDef* htim); -/* Blocking mode: Polling */ -HAL_StatusTypeDef HAL_TIM_OC_Start(TIM_HandleTypeDef* htim, uint32_t Channel); -HAL_StatusTypeDef HAL_TIM_OC_Stop(TIM_HandleTypeDef* htim, uint32_t Channel); -/* Non-Blocking mode: Interrupt */ -HAL_StatusTypeDef HAL_TIM_OC_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel); -HAL_StatusTypeDef HAL_TIM_OC_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel); -/* Non-Blocking mode: DMA */ -HAL_StatusTypeDef HAL_TIM_OC_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData, uint16_t Length); -HAL_StatusTypeDef HAL_TIM_OC_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel); - -/** - * @} - */ - -/** @addtogroup TIM_Exported_Functions_Group3 - * @{ - */ -/* Timer PWM functions *********************************************************/ -HAL_StatusTypeDef HAL_TIM_PWM_Init(TIM_HandleTypeDef* htim); -HAL_StatusTypeDef HAL_TIM_PWM_DeInit(TIM_HandleTypeDef* htim); -void HAL_TIM_PWM_MspInit(TIM_HandleTypeDef* htim); -void HAL_TIM_PWM_MspDeInit(TIM_HandleTypeDef* htim); -/* Blocking mode: Polling */ -HAL_StatusTypeDef HAL_TIM_PWM_Start(TIM_HandleTypeDef* htim, uint32_t Channel); -HAL_StatusTypeDef HAL_TIM_PWM_Stop(TIM_HandleTypeDef* htim, uint32_t Channel); -/* Non-Blocking mode: Interrupt */ -HAL_StatusTypeDef HAL_TIM_PWM_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel); -HAL_StatusTypeDef HAL_TIM_PWM_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel); -/* Non-Blocking mode: DMA */ -HAL_StatusTypeDef HAL_TIM_PWM_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData, uint16_t Length); -HAL_StatusTypeDef HAL_TIM_PWM_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel); - -/** - * @} - */ - -/** @addtogroup TIM_Exported_Functions_Group4 - * @{ - */ -/* Timer Input Capture functions ***********************************************/ -HAL_StatusTypeDef HAL_TIM_IC_Init(TIM_HandleTypeDef* htim); -HAL_StatusTypeDef HAL_TIM_IC_DeInit(TIM_HandleTypeDef* htim); -void HAL_TIM_IC_MspInit(TIM_HandleTypeDef* htim); -void HAL_TIM_IC_MspDeInit(TIM_HandleTypeDef* htim); -/* Blocking mode: Polling */ -HAL_StatusTypeDef HAL_TIM_IC_Start(TIM_HandleTypeDef* htim, uint32_t Channel); -HAL_StatusTypeDef HAL_TIM_IC_Stop(TIM_HandleTypeDef* htim, uint32_t Channel); -/* Non-Blocking mode: Interrupt */ -HAL_StatusTypeDef HAL_TIM_IC_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel); -HAL_StatusTypeDef HAL_TIM_IC_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel); -/* Non-Blocking mode: DMA */ -HAL_StatusTypeDef HAL_TIM_IC_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData, uint16_t Length); -HAL_StatusTypeDef HAL_TIM_IC_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel); - -/** - * @} - */ - -/** @addtogroup TIM_Exported_Functions_Group5 - * @{ - */ -/* Timer One Pulse functions ***************************************************/ -HAL_StatusTypeDef HAL_TIM_OnePulse_Init(TIM_HandleTypeDef* htim, uint32_t OnePulseMode); -HAL_StatusTypeDef HAL_TIM_OnePulse_DeInit(TIM_HandleTypeDef* htim); -void HAL_TIM_OnePulse_MspInit(TIM_HandleTypeDef* htim); -void HAL_TIM_OnePulse_MspDeInit(TIM_HandleTypeDef* htim); -/* Blocking mode: Polling */ -HAL_StatusTypeDef HAL_TIM_OnePulse_Start(TIM_HandleTypeDef* htim, uint32_t OutputChannel); -HAL_StatusTypeDef HAL_TIM_OnePulse_Stop(TIM_HandleTypeDef* htim, uint32_t OutputChannel); - -/* Non-Blocking mode: Interrupt */ -HAL_StatusTypeDef HAL_TIM_OnePulse_Start_IT(TIM_HandleTypeDef* htim, uint32_t OutputChannel); -HAL_StatusTypeDef HAL_TIM_OnePulse_Stop_IT(TIM_HandleTypeDef* htim, uint32_t OutputChannel); - -/** - * @} - */ - -/** @addtogroup TIM_Exported_Functions_Group6 - * @{ - */ -/* Timer Encoder functions *****************************************************/ -HAL_StatusTypeDef HAL_TIM_Encoder_Init(TIM_HandleTypeDef* htim, TIM_Encoder_InitTypeDef* sConfig); -HAL_StatusTypeDef HAL_TIM_Encoder_DeInit(TIM_HandleTypeDef* htim); -void HAL_TIM_Encoder_MspInit(TIM_HandleTypeDef* htim); -void HAL_TIM_Encoder_MspDeInit(TIM_HandleTypeDef* htim); -/* Blocking mode: Polling */ -HAL_StatusTypeDef HAL_TIM_Encoder_Start(TIM_HandleTypeDef* htim, uint32_t Channel); -HAL_StatusTypeDef HAL_TIM_Encoder_Stop(TIM_HandleTypeDef* htim, uint32_t Channel); -/* Non-Blocking mode: Interrupt */ -HAL_StatusTypeDef HAL_TIM_Encoder_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel); -HAL_StatusTypeDef HAL_TIM_Encoder_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel); -/* Non-Blocking mode: DMA */ -HAL_StatusTypeDef HAL_TIM_Encoder_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData1, uint32_t* pData2, uint16_t Length); -HAL_StatusTypeDef HAL_TIM_Encoder_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel); - -/** - * @} - */ - -/** @addtogroup TIM_Exported_Functions_Group7 - * @{ - */ -/* Interrupt Handler functions **********************************************/ -void HAL_TIM_IRQHandler(TIM_HandleTypeDef* htim); - -/** - * @} - */ - -/** @addtogroup TIM_Exported_Functions_Group8 - * @{ - */ -/* Control functions *********************************************************/ -HAL_StatusTypeDef HAL_TIM_OC_ConfigChannel(TIM_HandleTypeDef* htim, TIM_OC_InitTypeDef* sConfig, uint32_t Channel); -HAL_StatusTypeDef HAL_TIM_PWM_ConfigChannel(TIM_HandleTypeDef* htim, TIM_OC_InitTypeDef* sConfig, uint32_t Channel); -HAL_StatusTypeDef HAL_TIM_IC_ConfigChannel(TIM_HandleTypeDef* htim, TIM_IC_InitTypeDef* sConfig, uint32_t Channel); -HAL_StatusTypeDef HAL_TIM_OnePulse_ConfigChannel(TIM_HandleTypeDef* htim, TIM_OnePulse_InitTypeDef* sConfig, uint32_t OutputChannel, uint32_t InputChannel); -HAL_StatusTypeDef HAL_TIM_ConfigOCrefClear(TIM_HandleTypeDef* htim, TIM_ClearInputConfigTypeDef* sClearInputConfig, uint32_t Channel); -HAL_StatusTypeDef HAL_TIM_ConfigClockSource(TIM_HandleTypeDef* htim, TIM_ClockConfigTypeDef* sClockSourceConfig); -HAL_StatusTypeDef HAL_TIM_ConfigTI1Input(TIM_HandleTypeDef* htim, uint32_t TI1_Selection); -HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchronization(TIM_HandleTypeDef* htim, TIM_SlaveConfigTypeDef* sSlaveConfig); -HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchronization_IT(TIM_HandleTypeDef* htim, TIM_SlaveConfigTypeDef* sSlaveConfig); -HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStart(TIM_HandleTypeDef* htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc, \ - uint32_t* BurstBuffer, uint32_t BurstLength); -HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStop(TIM_HandleTypeDef* htim, uint32_t BurstRequestSrc); -HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStart(TIM_HandleTypeDef* htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc, \ - uint32_t* BurstBuffer, uint32_t BurstLength); -HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStop(TIM_HandleTypeDef* htim, uint32_t BurstRequestSrc); -HAL_StatusTypeDef HAL_TIM_GenerateEvent(TIM_HandleTypeDef* htim, uint32_t EventSource); -uint32_t HAL_TIM_ReadCapturedValue(TIM_HandleTypeDef* htim, uint32_t Channel); - -/** - * @} - */ - -/** @addtogroup TIM_Exported_Functions_Group9 - * @{ - */ -/* Callback in non blocking modes (Interrupt and DMA) *************************/ -void HAL_TIM_PeriodElapsedCallback(TIM_HandleTypeDef* htim); -void HAL_TIM_OC_DelayElapsedCallback(TIM_HandleTypeDef* htim); -void HAL_TIM_IC_CaptureCallback(TIM_HandleTypeDef* htim); -void HAL_TIM_PWM_PulseFinishedCallback(TIM_HandleTypeDef* htim); -void HAL_TIM_TriggerCallback(TIM_HandleTypeDef* htim); -void HAL_TIM_ErrorCallback(TIM_HandleTypeDef* htim); - -/** - * @} - */ - -/** @addtogroup TIM_Exported_Functions_Group10 - * @{ - */ -/* Peripheral State functions **************************************************/ -HAL_TIM_StateTypeDef HAL_TIM_Base_GetState(TIM_HandleTypeDef* htim); -HAL_TIM_StateTypeDef HAL_TIM_OC_GetState(TIM_HandleTypeDef* htim); -HAL_TIM_StateTypeDef HAL_TIM_PWM_GetState(TIM_HandleTypeDef* htim); -HAL_TIM_StateTypeDef HAL_TIM_IC_GetState(TIM_HandleTypeDef* htim); -HAL_TIM_StateTypeDef HAL_TIM_OnePulse_GetState(TIM_HandleTypeDef* htim); -HAL_TIM_StateTypeDef HAL_TIM_Encoder_GetState(TIM_HandleTypeDef* htim); - -/** - * @} - */ - -/** - * @} - */ - -/* Private macros ------------------------------------------------------------*/ -/** @defgroup TIM_Private_Macros TIM Private Macros - * @{ - */ - -/** @defgroup TIM_IS_TIM_Definitions TIM Private macros to check input parameters - * @{ - */ -#define IS_TIM_COUNTER_MODE(MODE) (((MODE) == TIM_COUNTERMODE_UP) || \ - ((MODE) == TIM_COUNTERMODE_DOWN) || \ - ((MODE) == TIM_COUNTERMODE_CENTERALIGNED1) || \ - ((MODE) == TIM_COUNTERMODE_CENTERALIGNED2) || \ - ((MODE) == TIM_COUNTERMODE_CENTERALIGNED3)) - -#define IS_TIM_CLOCKDIVISION_DIV(DIV) (((DIV) == TIM_CLOCKDIVISION_DIV1) || \ - ((DIV) == TIM_CLOCKDIVISION_DIV2) || \ - ((DIV) == TIM_CLOCKDIVISION_DIV4)) - -#define IS_TIM_PWM_MODE(MODE) (((MODE) == TIM_OCMODE_PWM1) || \ - ((MODE) == TIM_OCMODE_PWM2)) - -#define IS_TIM_OC_MODE(MODE) (((MODE) == TIM_OCMODE_TIMING) || \ - ((MODE) == TIM_OCMODE_ACTIVE) || \ - ((MODE) == TIM_OCMODE_INACTIVE) || \ - ((MODE) == TIM_OCMODE_TOGGLE) || \ - ((MODE) == TIM_OCMODE_FORCED_ACTIVE) || \ - ((MODE) == TIM_OCMODE_FORCED_INACTIVE)) - -#define IS_TIM_FAST_STATE(STATE) (((STATE) == TIM_OCFAST_DISABLE) || \ - ((STATE) == TIM_OCFAST_ENABLE)) - -#define IS_TIM_OC_POLARITY(POLARITY) (((POLARITY) == TIM_OCPOLARITY_HIGH) || \ - ((POLARITY) == TIM_OCPOLARITY_LOW)) - -#define IS_TIM_OCN_POLARITY(POLARITY) (((POLARITY) == TIM_OCNPOLARITY_HIGH) || \ - ((POLARITY) == TIM_OCNPOLARITY_LOW)) - -#define IS_TIM_OCIDLE_STATE(STATE) (((STATE) == TIM_OCIDLESTATE_SET) || \ - ((STATE) == TIM_OCIDLESTATE_RESET)) - -#define IS_TIM_OCNIDLE_STATE(STATE) (((STATE) == TIM_OCNIDLESTATE_SET) || \ - ((STATE) == TIM_OCNIDLESTATE_RESET)) - -#define IS_TIM_CHANNELS(CHANNEL) (((CHANNEL) == TIM_CHANNEL_1) || \ - ((CHANNEL) == TIM_CHANNEL_2) || \ - ((CHANNEL) == TIM_CHANNEL_3) || \ - ((CHANNEL) == TIM_CHANNEL_4) || \ - ((CHANNEL) == TIM_CHANNEL_ALL)) - -#define IS_TIM_OPM_CHANNELS(CHANNEL) (((CHANNEL) == TIM_CHANNEL_1) || \ - ((CHANNEL) == TIM_CHANNEL_2)) - -#define IS_TIM_COMPLEMENTARY_CHANNELS(CHANNEL) (((CHANNEL) == TIM_CHANNEL_1) || \ - ((CHANNEL) == TIM_CHANNEL_2) || \ - ((CHANNEL) == TIM_CHANNEL_3)) - -#define IS_TIM_IC_POLARITY(POLARITY) (((POLARITY) == TIM_ICPOLARITY_RISING) || \ - ((POLARITY) == TIM_ICPOLARITY_FALLING) || \ - ((POLARITY) == TIM_ICPOLARITY_BOTHEDGE)) - -#define IS_TIM_IC_SELECTION(SELECTION) (((SELECTION) == TIM_ICSELECTION_DIRECTTI) || \ - ((SELECTION) == TIM_ICSELECTION_INDIRECTTI) || \ - ((SELECTION) == TIM_ICSELECTION_TRC)) - -#define IS_TIM_IC_PRESCALER(PRESCALER) (((PRESCALER) == TIM_ICPSC_DIV1) || \ - ((PRESCALER) == TIM_ICPSC_DIV2) || \ - ((PRESCALER) == TIM_ICPSC_DIV4) || \ - ((PRESCALER) == TIM_ICPSC_DIV8)) - -#define IS_TIM_OPM_MODE(MODE) (((MODE) == TIM_OPMODE_SINGLE) || \ - ((MODE) == TIM_OPMODE_REPETITIVE)) - -#define IS_TIM_DMA_SOURCE(SOURCE) ((((SOURCE) & 0xFFFF80FFU) == 0x00000000U) && ((SOURCE) != 0x00000000U)) - -#define IS_TIM_ENCODER_MODE(MODE) (((MODE) == TIM_ENCODERMODE_TI1) || \ - ((MODE) == TIM_ENCODERMODE_TI2) || \ - ((MODE) == TIM_ENCODERMODE_TI12)) - -#define IS_TIM_EVENT_SOURCE(SOURCE) ((((SOURCE) & 0xFFFFFF00U) == 0x00000000U) && ((SOURCE) != 0x00000000U)) - -#define IS_TIM_CLOCKSOURCE(CLOCK) (((CLOCK) == TIM_CLOCKSOURCE_INTERNAL) || \ - ((CLOCK) == TIM_CLOCKSOURCE_ETRMODE2) || \ - ((CLOCK) == TIM_CLOCKSOURCE_ITR0) || \ - ((CLOCK) == TIM_CLOCKSOURCE_ITR1) || \ - ((CLOCK) == TIM_CLOCKSOURCE_ITR2) || \ - ((CLOCK) == TIM_CLOCKSOURCE_ITR3) || \ - ((CLOCK) == TIM_CLOCKSOURCE_TI1ED) || \ - ((CLOCK) == TIM_CLOCKSOURCE_TI1) || \ - ((CLOCK) == TIM_CLOCKSOURCE_TI2) || \ - ((CLOCK) == TIM_CLOCKSOURCE_ETRMODE1)) - -#define IS_TIM_CLOCKPOLARITY(POLARITY) (((POLARITY) == TIM_CLOCKPOLARITY_INVERTED) || \ - ((POLARITY) == TIM_CLOCKPOLARITY_NONINVERTED) || \ - ((POLARITY) == TIM_CLOCKPOLARITY_RISING) || \ - ((POLARITY) == TIM_CLOCKPOLARITY_FALLING) || \ - ((POLARITY) == TIM_CLOCKPOLARITY_BOTHEDGE)) - -#define IS_TIM_CLOCKPRESCALER(PRESCALER) (((PRESCALER) == TIM_CLOCKPRESCALER_DIV1) || \ - ((PRESCALER) == TIM_CLOCKPRESCALER_DIV2) || \ - ((PRESCALER) == TIM_CLOCKPRESCALER_DIV4) || \ - ((PRESCALER) == TIM_CLOCKPRESCALER_DIV8)) - -#define IS_TIM_CLOCKFILTER(ICFILTER) ((ICFILTER) <= 0x0FU) - -#define IS_TIM_CLEARINPUT_SOURCE(SOURCE) (((SOURCE) == TIM_CLEARINPUTSOURCE_NONE) || \ - ((SOURCE) == TIM_CLEARINPUTSOURCE_ETR)) - -#define IS_TIM_CLEARINPUT_POLARITY(POLARITY) (((POLARITY) == TIM_CLEARINPUTPOLARITY_INVERTED) || \ - ((POLARITY) == TIM_CLEARINPUTPOLARITY_NONINVERTED)) - -#define IS_TIM_CLEARINPUT_PRESCALER(PRESCALER) (((PRESCALER) == TIM_CLEARINPUTPRESCALER_DIV1) || \ - ((PRESCALER) == TIM_CLEARINPUTPRESCALER_DIV2) || \ - ((PRESCALER) == TIM_CLEARINPUTPRESCALER_DIV4) || \ - ((PRESCALER) == TIM_CLEARINPUTPRESCALER_DIV8)) - -#define IS_TIM_CLEARINPUT_FILTER(ICFILTER) ((ICFILTER) <= 0x0FU) - -#define IS_TIM_OSSR_STATE(STATE) (((STATE) == TIM_OSSR_ENABLE) || \ - ((STATE) == TIM_OSSR_DISABLE)) - -#define IS_TIM_OSSI_STATE(STATE) (((STATE) == TIM_OSSI_ENABLE) || \ - ((STATE) == TIM_OSSI_DISABLE)) - -#define IS_TIM_LOCK_LEVEL(LEVEL) (((LEVEL) == TIM_LOCKLEVEL_OFF) || \ - ((LEVEL) == TIM_LOCKLEVEL_1) || \ - ((LEVEL) == TIM_LOCKLEVEL_2) || \ - ((LEVEL) == TIM_LOCKLEVEL_3)) - -#define IS_TIM_BREAK_STATE(STATE) (((STATE) == TIM_BREAK_ENABLE) || \ - ((STATE) == TIM_BREAK_DISABLE)) - -#define IS_TIM_BREAK_POLARITY(POLARITY) (((POLARITY) == TIM_BREAKPOLARITY_LOW) || \ - ((POLARITY) == TIM_BREAKPOLARITY_HIGH)) - -#define IS_TIM_AUTOMATIC_OUTPUT_STATE(STATE) (((STATE) == TIM_AUTOMATICOUTPUT_ENABLE) || \ - ((STATE) == TIM_AUTOMATICOUTPUT_DISABLE)) - -#define IS_TIM_TRGO_SOURCE(SOURCE) (((SOURCE) == TIM_TRGO_RESET) || \ - ((SOURCE) == TIM_TRGO_ENABLE) || \ - ((SOURCE) == TIM_TRGO_UPDATE) || \ - ((SOURCE) == TIM_TRGO_OC1) || \ - ((SOURCE) == TIM_TRGO_OC1REF) || \ - ((SOURCE) == TIM_TRGO_OC2REF) || \ - ((SOURCE) == TIM_TRGO_OC3REF) || \ - ((SOURCE) == TIM_TRGO_OC4REF)) - -#define IS_TIM_SLAVE_MODE(MODE) (((MODE) == TIM_SLAVEMODE_DISABLE) || \ - ((MODE) == TIM_SLAVEMODE_GATED) || \ - ((MODE) == TIM_SLAVEMODE_RESET) || \ - ((MODE) == TIM_SLAVEMODE_TRIGGER) || \ - ((MODE) == TIM_SLAVEMODE_EXTERNAL1)) - -#define IS_TIM_MSM_STATE(STATE) (((STATE) == TIM_MASTERSLAVEMODE_ENABLE) || \ - ((STATE) == TIM_MASTERSLAVEMODE_DISABLE)) - -#define IS_TIM_TRIGGER_SELECTION(SELECTION) (((SELECTION) == TIM_TS_ITR0) || \ - ((SELECTION) == TIM_TS_ITR1) || \ - ((SELECTION) == TIM_TS_ITR2) || \ - ((SELECTION) == TIM_TS_ITR3) || \ - ((SELECTION) == TIM_TS_TI1F_ED) || \ - ((SELECTION) == TIM_TS_TI1FP1) || \ - ((SELECTION) == TIM_TS_TI2FP2) || \ - ((SELECTION) == TIM_TS_ETRF)) - -#define IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(SELECTION) (((SELECTION) == TIM_TS_ITR0) || \ - ((SELECTION) == TIM_TS_ITR1) || \ - ((SELECTION) == TIM_TS_ITR2) || \ - ((SELECTION) == TIM_TS_ITR3) || \ - ((SELECTION) == TIM_TS_NONE)) - -#define IS_TIM_TRIGGERPOLARITY(POLARITY) (((POLARITY) == TIM_TRIGGERPOLARITY_INVERTED ) || \ - ((POLARITY) == TIM_TRIGGERPOLARITY_NONINVERTED) || \ - ((POLARITY) == TIM_TRIGGERPOLARITY_RISING ) || \ - ((POLARITY) == TIM_TRIGGERPOLARITY_FALLING ) || \ - ((POLARITY) == TIM_TRIGGERPOLARITY_BOTHEDGE )) - -#define IS_TIM_TRIGGERPRESCALER(PRESCALER) (((PRESCALER) == TIM_TRIGGERPRESCALER_DIV1) || \ - ((PRESCALER) == TIM_TRIGGERPRESCALER_DIV2) || \ - ((PRESCALER) == TIM_TRIGGERPRESCALER_DIV4) || \ - ((PRESCALER) == TIM_TRIGGERPRESCALER_DIV8)) - -#define IS_TIM_TRIGGERFILTER(ICFILTER) ((ICFILTER) <= 0x0FU) - -#define IS_TIM_TI1SELECTION(TI1SELECTION) (((TI1SELECTION) == TIM_TI1SELECTION_CH1) || \ - ((TI1SELECTION) == TIM_TI1SELECTION_XORCOMBINATION)) - -#define IS_TIM_DMA_BASE(BASE) (((BASE) == TIM_DMABASE_CR1) || \ - ((BASE) == TIM_DMABASE_CR2) || \ - ((BASE) == TIM_DMABASE_SMCR) || \ - ((BASE) == TIM_DMABASE_DIER) || \ - ((BASE) == TIM_DMABASE_SR) || \ - ((BASE) == TIM_DMABASE_EGR) || \ - ((BASE) == TIM_DMABASE_CCMR1) || \ - ((BASE) == TIM_DMABASE_CCMR2) || \ - ((BASE) == TIM_DMABASE_CCER) || \ - ((BASE) == TIM_DMABASE_CNT) || \ - ((BASE) == TIM_DMABASE_PSC) || \ - ((BASE) == TIM_DMABASE_ARR) || \ - ((BASE) == TIM_DMABASE_RCR) || \ - ((BASE) == TIM_DMABASE_CCR1) || \ - ((BASE) == TIM_DMABASE_CCR2) || \ - ((BASE) == TIM_DMABASE_CCR3) || \ - ((BASE) == TIM_DMABASE_CCR4) || \ - ((BASE) == TIM_DMABASE_BDTR) || \ - ((BASE) == TIM_DMABASE_DCR) || \ - ((BASE) == TIM_DMABASE_OR)) - -#define IS_TIM_DMA_LENGTH(LENGTH) (((LENGTH) == TIM_DMABURSTLENGTH_1TRANSFER) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_2TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_3TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_4TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_5TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_6TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_7TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_8TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_9TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_10TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_11TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_12TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_13TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_14TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_15TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_16TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_17TRANSFERS) || \ - ((LENGTH) == TIM_DMABURSTLENGTH_18TRANSFERS)) - -#define IS_TIM_IC_FILTER(ICFILTER) ((ICFILTER) <= 0x0F) -/** - * @} - */ - -/** @defgroup TIM_Mask_Definitions TIM Mask Definition - * @{ - */ -/* The counter of a timer instance is disabled only if all the CCx and CCxN - channels have been disabled */ -#define TIM_CCER_CCxE_MASK ((uint32_t)(TIM_CCER_CC1E | TIM_CCER_CC2E | TIM_CCER_CC3E | TIM_CCER_CC4E)) -#define TIM_CCER_CCxNE_MASK ((uint32_t)(TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) -/** - * @} - */ - -/** - * @} - */ - -/* Private functions ---------------------------------------------------------*/ -/** @defgroup TIM_Private_Functions TIM Private Functions - * @{ - */ -void TIM_Base_SetConfig(TIM_TypeDef* TIMx, TIM_Base_InitTypeDef* Structure); -void TIM_TI1_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter); -void TIM_OC2_SetConfig(TIM_TypeDef* TIMx, TIM_OC_InitTypeDef* OC_Config); -void TIM_DMADelayPulseCplt(DMA_HandleTypeDef* hdma); -void TIM_DMAError(DMA_HandleTypeDef* hdma); -void TIM_DMACaptureCplt(DMA_HandleTypeDef* hdma); -void TIM_CCxChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelState); -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F4xx_HAL_TIM_H */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_tim_ex.h b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_tim_ex.h deleted file mode 100644 index 02a26402..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_tim_ex.h +++ /dev/null @@ -1,345 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_tim_ex.h - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Header file of TIM HAL Extension module. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_TIM_EX_H -#define __STM32F4xx_HAL_TIM_EX_H - -#ifdef __cplusplus -extern "C" { -#endif - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal_def.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @addtogroup TIMEx - * @{ - */ - -/* Exported types ------------------------------------------------------------*/ -/** @defgroup TIMEx_Exported_Types TIM Exported Types - * @{ - */ - -/** - * @brief TIM Hall sensor Configuration Structure definition - */ - -typedef struct -{ - - uint32_t IC1Polarity; /*!< Specifies the active edge of the input signal. - This parameter can be a value of @ref TIM_Input_Capture_Polarity */ - - uint32_t IC1Prescaler; /*!< Specifies the Input Capture Prescaler. - This parameter can be a value of @ref TIM_Input_Capture_Prescaler */ - - uint32_t IC1Filter; /*!< Specifies the input capture filter. - This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */ - - uint32_t Commutation_Delay; /*!< Specifies the pulse value to be loaded into the Capture Compare Register. - This parameter can be a number between Min_Data = 0x0000U and Max_Data = 0xFFFFU */ -} TIM_HallSensor_InitTypeDef; - -/** - * @brief TIM Master configuration Structure definition - */ -typedef struct -{ - uint32_t MasterOutputTrigger; /*!< Trigger output (TRGO) selection. - This parameter can be a value of @ref TIM_Master_Mode_Selection */ - - uint32_t MasterSlaveMode; /*!< Master/slave mode selection. - This parameter can be a value of @ref TIM_Master_Slave_Mode */ -} TIM_MasterConfigTypeDef; - -/** - * @brief TIM Break and Dead time configuration Structure definition - */ -typedef struct -{ - uint32_t OffStateRunMode; /*!< TIM off state in run mode. - This parameter can be a value of @ref TIM_OSSR_Off_State_Selection_for_Run_mode_state */ - uint32_t OffStateIDLEMode; /*!< TIM off state in IDLE mode. - This parameter can be a value of @ref TIM_OSSI_Off_State_Selection_for_Idle_mode_state */ - uint32_t LockLevel; /*!< TIM Lock level. - This parameter can be a value of @ref TIM_Lock_level */ - uint32_t DeadTime; /*!< TIM dead Time. - This parameter can be a number between Min_Data = 0x00 and Max_Data = 0xFF */ - uint32_t BreakState; /*!< TIM Break State. - This parameter can be a value of @ref TIM_Break_Input_enable_disable */ - uint32_t BreakPolarity; /*!< TIM Break input polarity. - This parameter can be a value of @ref TIM_Break_Polarity */ - uint32_t AutomaticOutput; /*!< TIM Automatic Output Enable state. - This parameter can be a value of @ref TIM_AOE_Bit_Set_Reset */ -} TIM_BreakDeadTimeConfigTypeDef; -/** - * @} - */ - -/* Exported constants --------------------------------------------------------*/ -/** @defgroup TIMEx_Exported_Constants TIM Exported Constants - * @{ - */ - -/** @defgroup TIMEx_Remap TIM Remap - * @{ - */ -#define TIM_TIM2_TIM8_TRGO (0x00000000U) -#define TIM_TIM2_ETH_PTP (0x00000400U) -#define TIM_TIM2_USBFS_SOF (0x00000800U) -#define TIM_TIM2_USBHS_SOF (0x00000C00U) -#define TIM_TIM5_GPIO (0x00000000U) -#define TIM_TIM5_LSI (0x00000040U) -#define TIM_TIM5_LSE (0x00000080U) -#define TIM_TIM5_RTC (0x000000C0U) -#define TIM_TIM11_GPIO (0x00000000U) -#define TIM_TIM11_HSE (0x00000002U) - -#if defined (STM32F446xx) -#define TIM_TIM11_SPDIFRX (0x00000001U) -#endif /* STM32F446xx */ -/** - * @} - */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -/** @defgroup TIMEx_SystemBreakInput TIM System Break Input - * @{ - */ -#define TIM_SYSTEMBREAKINPUT_HARDFAULT ((uint32_t)0x00000001U) /* Core Lockup lock output(Hardfault) is connected to Break Input of TIM1 and TIM8 */ -#define TIM_SYSTEMBREAKINPUT_PVD ((uint32_t)0x00000004U) /* PVD Interrupt is connected to Break Input of TIM1 and TIM8 */ -#define TIM_SYSTEMBREAKINPUT_HARDFAULT_PVD ((uint32_t)0x00000005U) /* Core Lockup lock output(Hardfault) and PVD Interrupt are connected to Break Input of TIM1 and TIM8 */ -/** - * @} - */ -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -/** - * @} - */ -/* Exported macro ------------------------------------------------------------*/ -/* Exported functions --------------------------------------------------------*/ -/** @addtogroup TIMEx_Exported_Functions - * @{ - */ - -/** @addtogroup TIMEx_Exported_Functions_Group1 - * @{ - */ -/* Timer Hall Sensor functions **********************************************/ -HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef* htim, TIM_HallSensor_InitTypeDef* sConfig); -HAL_StatusTypeDef HAL_TIMEx_HallSensor_DeInit(TIM_HandleTypeDef* htim); - -void HAL_TIMEx_HallSensor_MspInit(TIM_HandleTypeDef* htim); -void HAL_TIMEx_HallSensor_MspDeInit(TIM_HandleTypeDef* htim); - -/* Blocking mode: Polling */ -HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start(TIM_HandleTypeDef* htim); -HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop(TIM_HandleTypeDef* htim); -/* Non-Blocking mode: Interrupt */ -HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_IT(TIM_HandleTypeDef* htim); -HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_IT(TIM_HandleTypeDef* htim); -/* Non-Blocking mode: DMA */ -HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_DMA(TIM_HandleTypeDef* htim, uint32_t* pData, uint16_t Length); -HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_DMA(TIM_HandleTypeDef* htim); -/** - * @} - */ - -/** @addtogroup TIMEx_Exported_Functions_Group2 - * @{ - */ -/* Timer Complementary Output Compare functions *****************************/ -/* Blocking mode: Polling */ -HAL_StatusTypeDef HAL_TIMEx_OCN_Start(TIM_HandleTypeDef* htim, uint32_t Channel); -HAL_StatusTypeDef HAL_TIMEx_OCN_Stop(TIM_HandleTypeDef* htim, uint32_t Channel); - -/* Non-Blocking mode: Interrupt */ -HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel); -HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel); - -/* Non-Blocking mode: DMA */ -HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData, uint16_t Length); -HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel); -/** - * @} - */ - -/** @addtogroup TIMEx_Exported_Functions_Group3 - * @{ - */ -/* Timer Complementary PWM functions ****************************************/ -/* Blocking mode: Polling */ -HAL_StatusTypeDef HAL_TIMEx_PWMN_Start(TIM_HandleTypeDef* htim, uint32_t Channel); -HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop(TIM_HandleTypeDef* htim, uint32_t Channel); - -/* Non-Blocking mode: Interrupt */ -HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef* htim, uint32_t Channel); -HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT(TIM_HandleTypeDef* htim, uint32_t Channel); -/* Non-Blocking mode: DMA */ -HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef* htim, uint32_t Channel, uint32_t* pData, uint16_t Length); -HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef* htim, uint32_t Channel); -/** - * @} - */ - -/** @addtogroup TIMEx_Exported_Functions_Group4 - * @{ - */ -/* Timer Complementary One Pulse functions **********************************/ -/* Blocking mode: Polling */ -HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef* htim, uint32_t OutputChannel); -HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop(TIM_HandleTypeDef* htim, uint32_t OutputChannel); - -/* Non-Blocking mode: Interrupt */ -HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start_IT(TIM_HandleTypeDef* htim, uint32_t OutputChannel); -HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop_IT(TIM_HandleTypeDef* htim, uint32_t OutputChannel); -/** - * @} - */ - -/** @addtogroup TIMEx_Exported_Functions_Group5 - * @{ - */ -/* Extension Control functions ************************************************/ -HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent(TIM_HandleTypeDef* htim, uint32_t InputTrigger, uint32_t CommutationSource); -HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent_IT(TIM_HandleTypeDef* htim, uint32_t InputTrigger, uint32_t CommutationSource); -HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent_DMA(TIM_HandleTypeDef* htim, uint32_t InputTrigger, uint32_t CommutationSource); -HAL_StatusTypeDef HAL_TIMEx_MasterConfigSynchronization(TIM_HandleTypeDef* htim, TIM_MasterConfigTypeDef* sMasterConfig); -HAL_StatusTypeDef HAL_TIMEx_ConfigBreakDeadTime(TIM_HandleTypeDef* htim, TIM_BreakDeadTimeConfigTypeDef* sBreakDeadTimeConfig); -HAL_StatusTypeDef HAL_TIMEx_RemapConfig(TIM_HandleTypeDef* htim, uint32_t Remap); -/** - * @} - */ - -/** @addtogroup TIMEx_Exported_Functions_Group6 - * @{ - */ -/* Extension Callback *********************************************************/ -void HAL_TIMEx_CommutationCallback(TIM_HandleTypeDef* htim); -void HAL_TIMEx_BreakCallback(TIM_HandleTypeDef* htim); -void TIMEx_DMACommutationCplt(DMA_HandleTypeDef* hdma); -/** - * @} - */ - -/** @addtogroup TIMEx_Exported_Functions_Group7 - * @{ - */ -/* Extension Peripheral State functions **************************************/ -HAL_TIM_StateTypeDef HAL_TIMEx_HallSensor_GetState(TIM_HandleTypeDef* htim); -/** - * @} - */ - -/** - * @} - */ - -/* Private types -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/* Private constants ---------------------------------------------------------*/ -/* Private macros ------------------------------------------------------------*/ -/** @defgroup TIMEx_Private_Macros TIM Private Macros - * @{ - */ -#if defined (STM32F446xx) -#define IS_TIM_REMAP(TIM_REMAP) (((TIM_REMAP) == TIM_TIM2_TIM8_TRGO)||\ - ((TIM_REMAP) == TIM_TIM2_ETH_PTP)||\ - ((TIM_REMAP) == TIM_TIM2_USBFS_SOF)||\ - ((TIM_REMAP) == TIM_TIM2_USBHS_SOF)||\ - ((TIM_REMAP) == TIM_TIM5_GPIO)||\ - ((TIM_REMAP) == TIM_TIM5_LSI)||\ - ((TIM_REMAP) == TIM_TIM5_LSE)||\ - ((TIM_REMAP) == TIM_TIM5_RTC)||\ - ((TIM_REMAP) == TIM_TIM11_GPIO)||\ - ((TIM_REMAP) == TIM_TIM11_SPDIFRX)||\ - ((TIM_REMAP) == TIM_TIM11_HSE)) -#else -#define IS_TIM_REMAP(TIM_REMAP) (((TIM_REMAP) == TIM_TIM2_TIM8_TRGO)||\ - ((TIM_REMAP) == TIM_TIM2_ETH_PTP)||\ - ((TIM_REMAP) == TIM_TIM2_USBFS_SOF)||\ - ((TIM_REMAP) == TIM_TIM2_USBHS_SOF)||\ - ((TIM_REMAP) == TIM_TIM5_GPIO)||\ - ((TIM_REMAP) == TIM_TIM5_LSI)||\ - ((TIM_REMAP) == TIM_TIM5_LSE)||\ - ((TIM_REMAP) == TIM_TIM5_RTC)||\ - ((TIM_REMAP) == TIM_TIM11_GPIO)||\ - ((TIM_REMAP) == TIM_TIM11_HSE)) -#endif /* STM32F446xx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -#define IS_TIM_SYSTEMBREAKINPUT(BREAKINPUT) (((BREAKINPUT) == TIM_SYSTEMBREAKINPUT_HARDFAULT)||\ - ((BREAKINPUT) == TIM_SYSTEMBREAKINPUT_PVD)||\ - ((BREAKINPUT) == TIM_SYSTEMBREAKINPUT_HARDFAULT_PVD)) - -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -#define IS_TIM_DEADTIME(DEADTIME) ((DEADTIME) <= 0xFFU) -/** - * @} - */ - -/* Private functions ---------------------------------------------------------*/ -/** @defgroup TIMEx_Private_Functions TIM Private Functions - * @{ - */ - -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F4xx_HAL_TIM_EX_H */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_can.c b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_can.c deleted file mode 100644 index 23f9d607..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_can.c +++ /dev/null @@ -1,1382 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_can.c - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief This file provides firmware functions to manage the following - * functionalities of the Controller Area Network (CAN) peripheral: - * + Initialization and de-initialization functions - * + IO operation functions - * + Peripheral Control functions - * + Peripheral State and Error functions - * - @verbatim - ============================================================================== - ##### How to use this driver ##### - ============================================================================== - [..] - (#) Enable the CAN controller interface clock using - __HAL_RCC_CAN1_CLK_ENABLE() for CAN1 and __HAL_RCC_CAN2_CLK_ENABLE() for CAN2 - -@- In case you are using CAN2 only, you have to enable the CAN1 clock. - - (#) CAN pins configuration - (++) Enable the clock for the CAN GPIOs using the following function: - __GPIOx_CLK_ENABLE() - (++) Connect and configure the involved CAN pins to AF9 using the - following function HAL_GPIO_Init() - - (#) Initialize and configure the CAN using CAN_Init() function. - - (#) Transmit the desired CAN frame using HAL_CAN_Transmit() function. - - (#) Receive a CAN frame using HAL_CAN_Receive() function. - - *** Polling mode IO operation *** - ================================= - [..] - (+) Start the CAN peripheral transmission and wait the end of this operation - using HAL_CAN_Transmit(), at this stage user can specify the value of timeout - according to his end application - (+) Start the CAN peripheral reception and wait the end of this operation - using HAL_CAN_Receive(), at this stage user can specify the value of timeout - according to his end application - - *** Interrupt mode IO operation *** - =================================== - [..] - (+) Start the CAN peripheral transmission using HAL_CAN_Transmit_IT() - (+) Start the CAN peripheral reception using HAL_CAN_Receive_IT() - (+) Use HAL_CAN_IRQHandler() called under the used CAN Interrupt subroutine - (+) At CAN end of transmission HAL_CAN_TxCpltCallback() function is executed and user can - add his own code by customization of function pointer HAL_CAN_TxCpltCallback - (+) In case of CAN Error, HAL_CAN_ErrorCallback() function is executed and user can - add his own code by customization of function pointer HAL_CAN_ErrorCallback - - *** CAN HAL driver macros list *** - ============================================= - [..] - Below the list of most used macros in CAN HAL driver. - - (+) __HAL_CAN_ENABLE_IT: Enable the specified CAN interrupts - (+) __HAL_CAN_DISABLE_IT: Disable the specified CAN interrupts - (+) __HAL_CAN_GET_IT_SOURCE: Check if the specified CAN interrupt source is enabled or disabled - (+) __HAL_CAN_CLEAR_FLAG: Clear the CAN's pending flags - (+) __HAL_CAN_GET_FLAG: Get the selected CAN's flag status - - [..] - (@) You can refer to the CAN HAL driver header file for more useful macros - - @endverbatim - - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @defgroup CAN CAN - * @brief CAN driver modules - * @{ - */ - -#ifdef HAL_CAN_MODULE_ENABLED - -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) ||\ - defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) ||\ - defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) - -/* Private typedef -----------------------------------------------------------*/ -/* Private define ------------------------------------------------------------*/ -/** @addtogroup CAN_Private_Constants - * @{ - */ -#define CAN_TIMEOUT_VALUE 10U -/** - * @} - */ -/* Private macro -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/* Private function prototypes -----------------------------------------------*/ -/** @addtogroup CAN_Private_Functions - * @{ - */ -static HAL_StatusTypeDef CAN_Receive_IT(CAN_HandleTypeDef* hcan, uint8_t FIFONumber); -static HAL_StatusTypeDef CAN_Transmit_IT(CAN_HandleTypeDef* hcan); -/** - * @} - */ - -/* Exported functions --------------------------------------------------------*/ -/** @defgroup CAN_Exported_Functions CAN Exported Functions - * @{ - */ - -/** @defgroup CAN_Exported_Functions_Group1 Initialization and de-initialization functions - * @brief Initialization and Configuration functions - * -@verbatim - ============================================================================== - ##### Initialization and de-initialization functions ##### - ============================================================================== - [..] This section provides functions allowing to: - (+) Initialize and configure the CAN. - (+) De-initialize the CAN. - -@endverbatim - * @{ - */ - -/** - * @brief Initializes the CAN peripheral according to the specified - * parameters in the CAN_InitStruct. - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_CAN_Init(CAN_HandleTypeDef* hcan) -{ - uint32_t InitStatus = 3U; - uint32_t tickstart = 0U; - - /* Check CAN handle */ - if (hcan == NULL) - { - return HAL_ERROR; - } - - /* Check the parameters */ - assert_param(IS_CAN_ALL_INSTANCE(hcan->Instance)); - assert_param(IS_FUNCTIONAL_STATE(hcan->Init.TTCM)); - assert_param(IS_FUNCTIONAL_STATE(hcan->Init.ABOM)); - assert_param(IS_FUNCTIONAL_STATE(hcan->Init.AWUM)); - assert_param(IS_FUNCTIONAL_STATE(hcan->Init.NART)); - assert_param(IS_FUNCTIONAL_STATE(hcan->Init.RFLM)); - assert_param(IS_FUNCTIONAL_STATE(hcan->Init.TXFP)); - assert_param(IS_CAN_MODE(hcan->Init.Mode)); - assert_param(IS_CAN_SJW(hcan->Init.SJW)); - assert_param(IS_CAN_BS1(hcan->Init.BS1)); - assert_param(IS_CAN_BS2(hcan->Init.BS2)); - assert_param(IS_CAN_PRESCALER(hcan->Init.Prescaler)); - - if (hcan->State == HAL_CAN_STATE_RESET) - { - /* Allocate lock resource and initialize it */ - hcan->Lock = HAL_UNLOCKED; - /* Init the low level hardware */ - HAL_CAN_MspInit(hcan); - } - - /* Initialize the CAN state*/ - hcan->State = HAL_CAN_STATE_BUSY; - /* Exit from sleep mode */ - hcan->Instance->MCR &= (~(uint32_t)CAN_MCR_SLEEP); - /* Request initialisation */ - hcan->Instance->MCR |= CAN_MCR_INRQ ; - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait the acknowledge */ - while ((hcan->Instance->MSR & CAN_MSR_INAK) != CAN_MSR_INAK) - { - if ((HAL_GetTick() - tickstart ) > CAN_TIMEOUT_VALUE) - { - hcan->State = HAL_CAN_STATE_TIMEOUT; - /* Process unlocked */ - __HAL_UNLOCK(hcan); - return HAL_TIMEOUT; - } - } - - /* Check acknowledge */ - if ((hcan->Instance->MSR & CAN_MSR_INAK) != CAN_MSR_INAK) - { - InitStatus = CAN_INITSTATUS_FAILED; - } - else - { - /* Set the time triggered communication mode */ - if (hcan->Init.TTCM == ENABLE) - { - hcan->Instance->MCR |= CAN_MCR_TTCM; - } - else - { - hcan->Instance->MCR &= ~(uint32_t)CAN_MCR_TTCM; - } - - /* Set the automatic bus-off management */ - if (hcan->Init.ABOM == ENABLE) - { - hcan->Instance->MCR |= CAN_MCR_ABOM; - } - else - { - hcan->Instance->MCR &= ~(uint32_t)CAN_MCR_ABOM; - } - - /* Set the automatic wake-up mode */ - if (hcan->Init.AWUM == ENABLE) - { - hcan->Instance->MCR |= CAN_MCR_AWUM; - } - else - { - hcan->Instance->MCR &= ~(uint32_t)CAN_MCR_AWUM; - } - - /* Set the no automatic retransmission */ - if (hcan->Init.NART == ENABLE) - { - hcan->Instance->MCR |= CAN_MCR_NART; - } - else - { - hcan->Instance->MCR &= ~(uint32_t)CAN_MCR_NART; - } - - /* Set the receive FIFO locked mode */ - if (hcan->Init.RFLM == ENABLE) - { - hcan->Instance->MCR |= CAN_MCR_RFLM; - } - else - { - hcan->Instance->MCR &= ~(uint32_t)CAN_MCR_RFLM; - } - - /* Set the transmit FIFO priority */ - if (hcan->Init.TXFP == ENABLE) - { - hcan->Instance->MCR |= CAN_MCR_TXFP; - } - else - { - hcan->Instance->MCR &= ~(uint32_t)CAN_MCR_TXFP; - } - - /* Set the bit timing register */ - hcan->Instance->BTR = (uint32_t)((uint32_t)hcan->Init.Mode) | \ - ((uint32_t)hcan->Init.SJW) | \ - ((uint32_t)hcan->Init.BS1) | \ - ((uint32_t)hcan->Init.BS2) | \ - ((uint32_t)hcan->Init.Prescaler - 1U); - /* Request leave initialisation */ - hcan->Instance->MCR &= ~(uint32_t)CAN_MCR_INRQ; - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait the acknowledge */ - while ((hcan->Instance->MSR & CAN_MSR_INAK) == CAN_MSR_INAK) - { - if ((HAL_GetTick() - tickstart ) > CAN_TIMEOUT_VALUE) - { - hcan->State = HAL_CAN_STATE_TIMEOUT; - /* Process unlocked */ - __HAL_UNLOCK(hcan); - return HAL_TIMEOUT; - } - } - - /* Check acknowledged */ - if ((hcan->Instance->MSR & CAN_MSR_INAK) == CAN_MSR_INAK) - { - InitStatus = CAN_INITSTATUS_FAILED; - } - else - { - InitStatus = CAN_INITSTATUS_SUCCESS; - } - } - - if (InitStatus == CAN_INITSTATUS_SUCCESS) - { - /* Set CAN error code to none */ - hcan->ErrorCode = HAL_CAN_ERROR_NONE; - /* Initialize the CAN state */ - hcan->State = HAL_CAN_STATE_READY; - /* Return function status */ - return HAL_OK; - } - else - { - /* Initialize the CAN state */ - hcan->State = HAL_CAN_STATE_ERROR; - /* Return function status */ - return HAL_ERROR; - } -} - -/** - * @brief Configures the CAN reception filter according to the specified - * parameters in the CAN_FilterInitStruct. - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @param sFilterConfig: pointer to a CAN_FilterConfTypeDef structure that - * contains the filter configuration information. - * @retval None - */ -HAL_StatusTypeDef HAL_CAN_ConfigFilter(CAN_HandleTypeDef* hcan, CAN_FilterConfTypeDef* sFilterConfig) -{ - uint32_t filternbrbitpos = 0U; - /* Check the parameters */ - assert_param(IS_CAN_FILTER_NUMBER(sFilterConfig->FilterNumber)); - assert_param(IS_CAN_FILTER_MODE(sFilterConfig->FilterMode)); - assert_param(IS_CAN_FILTER_SCALE(sFilterConfig->FilterScale)); - assert_param(IS_CAN_FILTER_FIFO(sFilterConfig->FilterFIFOAssignment)); - assert_param(IS_FUNCTIONAL_STATE(sFilterConfig->FilterActivation)); - assert_param(IS_CAN_BANKNUMBER(sFilterConfig->BankNumber)); - filternbrbitpos = ((uint32_t)1U) << sFilterConfig->FilterNumber; - /* Initialisation mode for the filter */ - CAN1->FMR |= (uint32_t)CAN_FMR_FINIT; - /* Select the start slave bank */ - CAN1->FMR &= ~((uint32_t)CAN_FMR_CAN2SB); - CAN1->FMR |= (uint32_t)(sFilterConfig->BankNumber << 8U); - /* Filter Deactivation */ - CAN1->FA1R &= ~(uint32_t)filternbrbitpos; - - /* Filter Scale */ - if (sFilterConfig->FilterScale == CAN_FILTERSCALE_16BIT) - { - /* 16-bit scale for the filter */ - CAN1->FS1R &= ~(uint32_t)filternbrbitpos; - /* First 16-bit identifier and First 16-bit mask */ - /* Or First 16-bit identifier and Second 16-bit identifier */ - CAN1->sFilterRegister[sFilterConfig->FilterNumber].FR1 = - ((0x0000FFFFU & (uint32_t)sFilterConfig->FilterMaskIdLow) << 16U) | - (0x0000FFFFU & (uint32_t)sFilterConfig->FilterIdLow); - /* Second 16-bit identifier and Second 16-bit mask */ - /* Or Third 16-bit identifier and Fourth 16-bit identifier */ - CAN1->sFilterRegister[sFilterConfig->FilterNumber].FR2 = - ((0x0000FFFFU & (uint32_t)sFilterConfig->FilterMaskIdHigh) << 16U) | - (0x0000FFFFU & (uint32_t)sFilterConfig->FilterIdHigh); - } - - if (sFilterConfig->FilterScale == CAN_FILTERSCALE_32BIT) - { - /* 32-bit scale for the filter */ - CAN1->FS1R |= filternbrbitpos; - /* 32-bit identifier or First 32-bit identifier */ - CAN1->sFilterRegister[sFilterConfig->FilterNumber].FR1 = - ((0x0000FFFFU & (uint32_t)sFilterConfig->FilterIdHigh) << 16U) | - (0x0000FFFFU & (uint32_t)sFilterConfig->FilterIdLow); - /* 32-bit mask or Second 32-bit identifier */ - CAN1->sFilterRegister[sFilterConfig->FilterNumber].FR2 = - ((0x0000FFFFU & (uint32_t)sFilterConfig->FilterMaskIdHigh) << 16U) | - (0x0000FFFFU & (uint32_t)sFilterConfig->FilterMaskIdLow); - } - - /* Filter Mode */ - if (sFilterConfig->FilterMode == CAN_FILTERMODE_IDMASK) - { - /*Id/Mask mode for the filter*/ - CAN1->FM1R &= ~(uint32_t)filternbrbitpos; - } - else /* CAN_FilterInitStruct->CAN_FilterMode == CAN_FilterMode_IdList */ - { - /*Identifier list mode for the filter*/ - CAN1->FM1R |= (uint32_t)filternbrbitpos; - } - - /* Filter FIFO assignment */ - if (sFilterConfig->FilterFIFOAssignment == CAN_FILTER_FIFO0) - { - /* FIFO 0 assignation for the filter */ - CAN1->FFA1R &= ~(uint32_t)filternbrbitpos; - } - - if (sFilterConfig->FilterFIFOAssignment == CAN_FILTER_FIFO1) - { - /* FIFO 1 assignation for the filter */ - CAN1->FFA1R |= (uint32_t)filternbrbitpos; - } - - /* Filter activation */ - if (sFilterConfig->FilterActivation == ENABLE) - { - CAN1->FA1R |= filternbrbitpos; - } - - /* Leave the initialisation mode for the filter */ - CAN1->FMR &= ~((uint32_t)CAN_FMR_FINIT); - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Deinitializes the CANx peripheral registers to their default reset values. - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_CAN_DeInit(CAN_HandleTypeDef* hcan) -{ - /* Check CAN handle */ - if (hcan == NULL) - { - return HAL_ERROR; - } - - /* Check the parameters */ - assert_param(IS_CAN_ALL_INSTANCE(hcan->Instance)); - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_BUSY; - /* DeInit the low level hardware */ - HAL_CAN_MspDeInit(hcan); - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_RESET; - /* Release Lock */ - __HAL_UNLOCK(hcan); - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Initializes the CAN MSP. - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @retval None - */ -__weak void HAL_CAN_MspInit(CAN_HandleTypeDef* hcan) -{ - /* Prevent unused argument(s) compilation warning */ - UNUSED(hcan); - /* NOTE : This function Should not be modified, when the callback is needed, - the HAL_CAN_MspInit could be implemented in the user file - */ -} - -/** - * @brief DeInitializes the CAN MSP. - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @retval None - */ -__weak void HAL_CAN_MspDeInit(CAN_HandleTypeDef* hcan) -{ - /* Prevent unused argument(s) compilation warning */ - UNUSED(hcan); - /* NOTE : This function Should not be modified, when the callback is needed, - the HAL_CAN_MspDeInit could be implemented in the user file - */ -} - -/** - * @} - */ - -/** @defgroup CAN_Exported_Functions_Group2 IO operation functions - * @brief IO operation functions - * -@verbatim - ============================================================================== - ##### IO operation functions ##### - ============================================================================== - [..] This section provides functions allowing to: - (+) Transmit a CAN frame message. - (+) Receive a CAN frame message. - (+) Enter CAN peripheral in sleep mode. - (+) Wake up the CAN peripheral from sleep mode. - -@endverbatim - * @{ - */ - -/** - * @brief Initiates and transmits a CAN frame message. - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @param Timeout: Specify Timeout value - * @retval HAL status - */ -HAL_StatusTypeDef HAL_CAN_Transmit(CAN_HandleTypeDef* hcan, uint32_t Timeout) -{ - uint32_t transmitmailbox = 5U; - uint32_t tickstart = 0U; - /* Check the parameters */ - assert_param(IS_CAN_IDTYPE(hcan->pTxMsg->IDE)); - assert_param(IS_CAN_RTR(hcan->pTxMsg->RTR)); - assert_param(IS_CAN_DLC(hcan->pTxMsg->DLC)); - - if (((hcan->Instance->TSR & CAN_TSR_TME0) == CAN_TSR_TME0) || \ - ((hcan->Instance->TSR & CAN_TSR_TME1) == CAN_TSR_TME1) || \ - ((hcan->Instance->TSR & CAN_TSR_TME2) == CAN_TSR_TME2)) - { - /* Process locked */ - __HAL_LOCK(hcan); - - if (hcan->State == HAL_CAN_STATE_BUSY_RX) - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_BUSY_TX_RX; - } - else - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_BUSY_TX; - } - - /* Select one empty transmit mailbox */ - if ((hcan->Instance->TSR & CAN_TSR_TME0) == CAN_TSR_TME0) - { - transmitmailbox = 0U; - } - else if ((hcan->Instance->TSR & CAN_TSR_TME1) == CAN_TSR_TME1) - { - transmitmailbox = 1U; - } - else - { - transmitmailbox = 2U; - } - - /* Set up the Id */ - hcan->Instance->sTxMailBox[transmitmailbox].TIR &= CAN_TI0R_TXRQ; - - if (hcan->pTxMsg->IDE == CAN_ID_STD) - { - assert_param(IS_CAN_STDID(hcan->pTxMsg->StdId)); - hcan->Instance->sTxMailBox[transmitmailbox].TIR |= ((hcan->pTxMsg->StdId << 21U) | \ - hcan->pTxMsg->RTR); - } - else - { - assert_param(IS_CAN_EXTID(hcan->pTxMsg->ExtId)); - hcan->Instance->sTxMailBox[transmitmailbox].TIR |= ((hcan->pTxMsg->ExtId << 3U) | \ - hcan->pTxMsg->IDE | \ - hcan->pTxMsg->RTR); - } - - /* Set up the DLC */ - hcan->pTxMsg->DLC &= (uint8_t)0x0000000FU; - hcan->Instance->sTxMailBox[transmitmailbox].TDTR &= (uint32_t)0xFFFFFFF0U; - hcan->Instance->sTxMailBox[transmitmailbox].TDTR |= hcan->pTxMsg->DLC; - /* Set up the data field */ - hcan->Instance->sTxMailBox[transmitmailbox].TDLR = (((uint32_t)hcan->pTxMsg->Data[3U] << 24U) | - ((uint32_t)hcan->pTxMsg->Data[2U] << 16U) | - ((uint32_t)hcan->pTxMsg->Data[1U] << 8U) | - ((uint32_t)hcan->pTxMsg->Data[0U])); - hcan->Instance->sTxMailBox[transmitmailbox].TDHR = (((uint32_t)hcan->pTxMsg->Data[7U] << 24U) | - ((uint32_t)hcan->pTxMsg->Data[6U] << 16U) | - ((uint32_t)hcan->pTxMsg->Data[5U] << 8U) | - ((uint32_t)hcan->pTxMsg->Data[4U])); - /* Request transmission */ - hcan->Instance->sTxMailBox[transmitmailbox].TIR |= CAN_TI0R_TXRQ; - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Check End of transmission flag */ - while (!(__HAL_CAN_TRANSMIT_STATUS(hcan, transmitmailbox))) - { - /* Check for the Timeout */ - if (Timeout != HAL_MAX_DELAY) - { - if ((Timeout == 0U) || ((HAL_GetTick() - tickstart ) > Timeout)) - { - hcan->State = HAL_CAN_STATE_TIMEOUT; - /* Process unlocked */ - __HAL_UNLOCK(hcan); - return HAL_TIMEOUT; - } - } - } - - if (hcan->State == HAL_CAN_STATE_BUSY_TX_RX) - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_BUSY_RX; - } - else - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_READY; - } - - /* Process unlocked */ - __HAL_UNLOCK(hcan); - /* Return function status */ - return HAL_OK; - } - else - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_ERROR; - /* Return function status */ - return HAL_ERROR; - } -} - -/** - * @brief Initiates and transmits a CAN frame message. - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_CAN_Transmit_IT(CAN_HandleTypeDef* hcan) -{ - uint32_t transmitmailbox = 5U; - /* Check the parameters */ - assert_param(IS_CAN_IDTYPE(hcan->pTxMsg->IDE)); - assert_param(IS_CAN_RTR(hcan->pTxMsg->RTR)); - assert_param(IS_CAN_DLC(hcan->pTxMsg->DLC)); - - if (((hcan->Instance->TSR & CAN_TSR_TME0) == CAN_TSR_TME0) || \ - ((hcan->Instance->TSR & CAN_TSR_TME1) == CAN_TSR_TME1) || \ - ((hcan->Instance->TSR & CAN_TSR_TME2) == CAN_TSR_TME2)) - { - /* Process Locked */ - __HAL_LOCK(hcan); - - /* Select one empty transmit mailbox */ - if ((hcan->Instance->TSR & CAN_TSR_TME0) == CAN_TSR_TME0) - { - transmitmailbox = 0U; - } - else if ((hcan->Instance->TSR & CAN_TSR_TME1) == CAN_TSR_TME1) - { - transmitmailbox = 1U; - } - else - { - transmitmailbox = 2U; - } - - /* Set up the Id */ - hcan->Instance->sTxMailBox[transmitmailbox].TIR &= CAN_TI0R_TXRQ; - - if (hcan->pTxMsg->IDE == CAN_ID_STD) - { - assert_param(IS_CAN_STDID(hcan->pTxMsg->StdId)); - hcan->Instance->sTxMailBox[transmitmailbox].TIR |= ((hcan->pTxMsg->StdId << 21U) | \ - hcan->pTxMsg->RTR); - } - else - { - assert_param(IS_CAN_EXTID(hcan->pTxMsg->ExtId)); - hcan->Instance->sTxMailBox[transmitmailbox].TIR |= ((hcan->pTxMsg->ExtId << 3U) | \ - hcan->pTxMsg->IDE | \ - hcan->pTxMsg->RTR); - } - - /* Set up the DLC */ - hcan->pTxMsg->DLC &= (uint8_t)0x0000000FU; - hcan->Instance->sTxMailBox[transmitmailbox].TDTR &= (uint32_t)0xFFFFFFF0U; - hcan->Instance->sTxMailBox[transmitmailbox].TDTR |= hcan->pTxMsg->DLC; - /* Set up the data field */ - hcan->Instance->sTxMailBox[transmitmailbox].TDLR = (((uint32_t)hcan->pTxMsg->Data[3U] << 24U) | - ((uint32_t)hcan->pTxMsg->Data[2U] << 16U) | - ((uint32_t)hcan->pTxMsg->Data[1U] << 8U) | - ((uint32_t)hcan->pTxMsg->Data[0U])); - hcan->Instance->sTxMailBox[transmitmailbox].TDHR = (((uint32_t)hcan->pTxMsg->Data[7U] << 24U) | - ((uint32_t)hcan->pTxMsg->Data[6U] << 16U) | - ((uint32_t)hcan->pTxMsg->Data[5U] << 8U) | - ((uint32_t)hcan->pTxMsg->Data[4U])); - - if (hcan->State == HAL_CAN_STATE_BUSY_RX) - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_BUSY_TX_RX; - } - else - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_BUSY_TX; - } - - /* Set CAN error code to none */ - hcan->ErrorCode = HAL_CAN_ERROR_NONE; - /* Process Unlocked */ - __HAL_UNLOCK(hcan); - /* Enable Error warning Interrupt */ - __HAL_CAN_ENABLE_IT(hcan, CAN_IT_EWG); - /* Enable Error passive Interrupt */ - __HAL_CAN_ENABLE_IT(hcan, CAN_IT_EPV); - /* Enable Bus-off Interrupt */ - __HAL_CAN_ENABLE_IT(hcan, CAN_IT_BOF); - /* Enable Last error code Interrupt */ - __HAL_CAN_ENABLE_IT(hcan, CAN_IT_LEC); - /* Enable Error Interrupt */ - __HAL_CAN_ENABLE_IT(hcan, CAN_IT_ERR); - /* Enable Transmit mailbox empty Interrupt */ - __HAL_CAN_ENABLE_IT(hcan, CAN_IT_TME); - /* Request transmission */ - hcan->Instance->sTxMailBox[transmitmailbox].TIR |= CAN_TI0R_TXRQ; - } - else - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_ERROR; - /* Return function status */ - return HAL_ERROR; - } - - return HAL_OK; -} - -/** - * @brief Receives a correct CAN frame. - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @param FIFONumber: FIFO Number value - * @param Timeout: Specify Timeout value - * @retval HAL status - */ -HAL_StatusTypeDef HAL_CAN_Receive(CAN_HandleTypeDef* hcan, uint8_t FIFONumber, uint32_t Timeout) -{ - uint32_t tickstart = 0U; - /* Check the parameters */ - assert_param(IS_CAN_FIFO(FIFONumber)); - /* Process locked */ - __HAL_LOCK(hcan); - - if (hcan->State == HAL_CAN_STATE_BUSY_TX) - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_BUSY_TX_RX; - } - else - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_BUSY_RX; - } - - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Check pending message */ - while (__HAL_CAN_MSG_PENDING(hcan, FIFONumber) == 0U) - { - /* Check for the Timeout */ - if (Timeout != HAL_MAX_DELAY) - { - if ((Timeout == 0U) || ((HAL_GetTick() - tickstart ) > Timeout)) - { - hcan->State = HAL_CAN_STATE_TIMEOUT; - /* Process unlocked */ - __HAL_UNLOCK(hcan); - return HAL_TIMEOUT; - } - } - } - - /* Get the Id */ - hcan->pRxMsg->IDE = (uint8_t)0x04U & hcan->Instance->sFIFOMailBox[FIFONumber].RIR; - - if (hcan->pRxMsg->IDE == CAN_ID_STD) - { - hcan->pRxMsg->StdId = (uint32_t)0x000007FFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RIR >> 21U); - } - else - { - hcan->pRxMsg->ExtId = (uint32_t)0x1FFFFFFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RIR >> 3U); - } - - hcan->pRxMsg->RTR = (uint8_t)0x02U & hcan->Instance->sFIFOMailBox[FIFONumber].RIR; - /* Get the DLC */ - hcan->pRxMsg->DLC = (uint8_t)0x0FU & hcan->Instance->sFIFOMailBox[FIFONumber].RDTR; - /* Get the FMI */ - hcan->pRxMsg->FMI = (uint8_t)0xFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RDTR >> 8U); - /* Get the data field */ - hcan->pRxMsg->Data[0U] = (uint8_t)0xFFU & hcan->Instance->sFIFOMailBox[FIFONumber].RDLR; - hcan->pRxMsg->Data[1U] = (uint8_t)0xFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RDLR >> 8U); - hcan->pRxMsg->Data[2U] = (uint8_t)0xFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RDLR >> 16U); - hcan->pRxMsg->Data[3U] = (uint8_t)0xFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RDLR >> 24U); - hcan->pRxMsg->Data[4U] = (uint8_t)0xFFU & hcan->Instance->sFIFOMailBox[FIFONumber].RDHR; - hcan->pRxMsg->Data[5U] = (uint8_t)0xFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RDHR >> 8U); - hcan->pRxMsg->Data[6U] = (uint8_t)0xFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RDHR >> 16U); - hcan->pRxMsg->Data[7U] = (uint8_t)0xFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RDHR >> 24U); - - /* Release the FIFO */ - if (FIFONumber == CAN_FIFO0) - { - /* Release FIFO0 */ - __HAL_CAN_FIFO_RELEASE(hcan, CAN_FIFO0); - } - else /* FIFONumber == CAN_FIFO1 */ - { - /* Release FIFO1 */ - __HAL_CAN_FIFO_RELEASE(hcan, CAN_FIFO1); - } - - if (hcan->State == HAL_CAN_STATE_BUSY_TX_RX) - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_BUSY_TX; - /* Process unlocked */ - __HAL_UNLOCK(hcan); - } - else - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_READY; - /* Process unlocked */ - __HAL_UNLOCK(hcan); - } - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Receives a correct CAN frame. - * @param hcan: Pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @param FIFONumber: Specify the FIFO number - * @retval HAL status - */ -HAL_StatusTypeDef HAL_CAN_Receive_IT(CAN_HandleTypeDef* hcan, uint8_t FIFONumber) -{ - uint32_t tmp = 0U; - /* Check the parameters */ - assert_param(IS_CAN_FIFO(FIFONumber)); - tmp = hcan->State; - - if ((tmp == HAL_CAN_STATE_READY) || (tmp == HAL_CAN_STATE_BUSY_TX)) - { - /* Process locked */ - __HAL_LOCK(hcan); - - if (hcan->State == HAL_CAN_STATE_BUSY_TX) - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_BUSY_TX_RX; - } - else - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_BUSY_RX; - } - - /* Set CAN error code to none */ - hcan->ErrorCode = HAL_CAN_ERROR_NONE; - /* Enable Error warning Interrupt */ - __HAL_CAN_ENABLE_IT(hcan, CAN_IT_EWG); - /* Enable Error passive Interrupt */ - __HAL_CAN_ENABLE_IT(hcan, CAN_IT_EPV); - /* Enable Bus-off Interrupt */ - __HAL_CAN_ENABLE_IT(hcan, CAN_IT_BOF); - /* Enable Last error code Interrupt */ - __HAL_CAN_ENABLE_IT(hcan, CAN_IT_LEC); - /* Enable Error Interrupt */ - __HAL_CAN_ENABLE_IT(hcan, CAN_IT_ERR); - /* Process unlocked */ - __HAL_UNLOCK(hcan); - - if (FIFONumber == CAN_FIFO0) - { - /* Enable FIFO 0 message pending Interrupt */ - __HAL_CAN_ENABLE_IT(hcan, CAN_IT_FMP0); - } - else - { - /* Enable FIFO 1 message pending Interrupt */ - __HAL_CAN_ENABLE_IT(hcan, CAN_IT_FMP1); - } - } - else - { - return HAL_BUSY; - } - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Enters the Sleep (low power) mode. - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @retval HAL status. - */ -HAL_StatusTypeDef HAL_CAN_Sleep(CAN_HandleTypeDef* hcan) -{ - uint32_t tickstart = 0U; - /* Process locked */ - __HAL_LOCK(hcan); - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_BUSY; - /* Request Sleep mode */ - hcan->Instance->MCR = (((hcan->Instance->MCR) & (uint32_t)(~(uint32_t)CAN_MCR_INRQ)) | CAN_MCR_SLEEP); - - /* Sleep mode status */ - if ((hcan->Instance->MSR & (CAN_MSR_SLAK | CAN_MSR_INAK)) != CAN_MSR_SLAK) - { - /* Process unlocked */ - __HAL_UNLOCK(hcan); - /* Return function status */ - return HAL_ERROR; - } - - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait the acknowledge */ - while ((hcan->Instance->MSR & (CAN_MSR_SLAK | CAN_MSR_INAK)) != CAN_MSR_SLAK) - { - if ((HAL_GetTick() - tickstart) > CAN_TIMEOUT_VALUE) - { - hcan->State = HAL_CAN_STATE_TIMEOUT; - /* Process unlocked */ - __HAL_UNLOCK(hcan); - return HAL_TIMEOUT; - } - } - - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_READY; - /* Process unlocked */ - __HAL_UNLOCK(hcan); - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Wakes up the CAN peripheral from sleep mode, after that the CAN peripheral - * is in the normal mode. - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @retval HAL status. - */ -HAL_StatusTypeDef HAL_CAN_WakeUp(CAN_HandleTypeDef* hcan) -{ - uint32_t tickstart = 0U; - /* Process locked */ - __HAL_LOCK(hcan); - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_BUSY; - /* Wake up request */ - hcan->Instance->MCR &= ~(uint32_t)CAN_MCR_SLEEP; - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Sleep mode status */ - while ((hcan->Instance->MSR & CAN_MSR_SLAK) == CAN_MSR_SLAK) - { - if ((HAL_GetTick() - tickstart) > CAN_TIMEOUT_VALUE) - { - hcan->State = HAL_CAN_STATE_TIMEOUT; - /* Process unlocked */ - __HAL_UNLOCK(hcan); - return HAL_TIMEOUT; - } - } - - if ((hcan->Instance->MSR & CAN_MSR_SLAK) == CAN_MSR_SLAK) - { - /* Process unlocked */ - __HAL_UNLOCK(hcan); - /* Return function status */ - return HAL_ERROR; - } - - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_READY; - /* Process unlocked */ - __HAL_UNLOCK(hcan); - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Handles CAN interrupt request - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @retval None - */ -void HAL_CAN_IRQHandler(CAN_HandleTypeDef* hcan) -{ - uint32_t tmp1 = 0U, tmp2 = 0U, tmp3 = 0U; - - /* Check End of transmission flag */ - if (__HAL_CAN_GET_IT_SOURCE(hcan, CAN_IT_TME)) - { - tmp1 = __HAL_CAN_TRANSMIT_STATUS(hcan, CAN_TXMAILBOX_0); - tmp2 = __HAL_CAN_TRANSMIT_STATUS(hcan, CAN_TXMAILBOX_1); - tmp3 = __HAL_CAN_TRANSMIT_STATUS(hcan, CAN_TXMAILBOX_2); - - if (tmp1 || tmp2 || tmp3) - { - /* Call transmit function */ - CAN_Transmit_IT(hcan); - } - } - - tmp1 = __HAL_CAN_MSG_PENDING(hcan, CAN_FIFO0); - tmp2 = __HAL_CAN_GET_IT_SOURCE(hcan, CAN_IT_FMP0); - - /* Check End of reception flag for FIFO0 */ - if ((tmp1 != 0U) && tmp2) - { - /* Call receive function */ - CAN_Receive_IT(hcan, CAN_FIFO0); - } - - tmp1 = __HAL_CAN_MSG_PENDING(hcan, CAN_FIFO1); - tmp2 = __HAL_CAN_GET_IT_SOURCE(hcan, CAN_IT_FMP1); - - /* Check End of reception flag for FIFO1 */ - if ((tmp1 != 0U) && tmp2) - { - /* Call receive function */ - CAN_Receive_IT(hcan, CAN_FIFO1); - } - - tmp1 = __HAL_CAN_GET_FLAG(hcan, CAN_FLAG_EWG); - tmp2 = __HAL_CAN_GET_IT_SOURCE(hcan, CAN_IT_EWG); - tmp3 = __HAL_CAN_GET_IT_SOURCE(hcan, CAN_IT_ERR); - - /* Check Error Warning Flag */ - if (tmp1 && tmp2 && tmp3) - { - /* Set CAN error code to EWG error */ - hcan->ErrorCode |= HAL_CAN_ERROR_EWG; - } - - tmp1 = __HAL_CAN_GET_FLAG(hcan, CAN_FLAG_EPV); - tmp2 = __HAL_CAN_GET_IT_SOURCE(hcan, CAN_IT_EPV); - tmp3 = __HAL_CAN_GET_IT_SOURCE(hcan, CAN_IT_ERR); - - /* Check Error Passive Flag */ - if (tmp1 && tmp2 && tmp3) - { - /* Set CAN error code to EPV error */ - hcan->ErrorCode |= HAL_CAN_ERROR_EPV; - } - - tmp1 = __HAL_CAN_GET_FLAG(hcan, CAN_FLAG_BOF); - tmp2 = __HAL_CAN_GET_IT_SOURCE(hcan, CAN_IT_BOF); - tmp3 = __HAL_CAN_GET_IT_SOURCE(hcan, CAN_IT_ERR); - - /* Check Bus-Off Flag */ - if (tmp1 && tmp2 && tmp3) - { - /* Set CAN error code to BOF error */ - hcan->ErrorCode |= HAL_CAN_ERROR_BOF; - } - - tmp1 = HAL_IS_BIT_CLR(hcan->Instance->ESR, CAN_ESR_LEC); - tmp2 = __HAL_CAN_GET_IT_SOURCE(hcan, CAN_IT_LEC); - tmp3 = __HAL_CAN_GET_IT_SOURCE(hcan, CAN_IT_ERR); - - /* Check Last error code Flag */ - if ((!tmp1) && tmp2 && tmp3) - { - tmp1 = (hcan->Instance->ESR) & CAN_ESR_LEC; - - switch (tmp1) - { - case (CAN_ESR_LEC_0): - /* Set CAN error code to STF error */ - hcan->ErrorCode |= HAL_CAN_ERROR_STF; - break; - - case (CAN_ESR_LEC_1): - /* Set CAN error code to FOR error */ - hcan->ErrorCode |= HAL_CAN_ERROR_FOR; - break; - - case (CAN_ESR_LEC_1 | CAN_ESR_LEC_0): - /* Set CAN error code to ACK error */ - hcan->ErrorCode |= HAL_CAN_ERROR_ACK; - break; - - case (CAN_ESR_LEC_2): - /* Set CAN error code to BR error */ - hcan->ErrorCode |= HAL_CAN_ERROR_BR; - break; - - case (CAN_ESR_LEC_2 | CAN_ESR_LEC_0): - /* Set CAN error code to BD error */ - hcan->ErrorCode |= HAL_CAN_ERROR_BD; - break; - - case (CAN_ESR_LEC_2 | CAN_ESR_LEC_1): - /* Set CAN error code to CRC error */ - hcan->ErrorCode |= HAL_CAN_ERROR_CRC; - break; - - default: - break; - } - - /* Clear Last error code Flag */ - hcan->Instance->ESR &= ~(CAN_ESR_LEC); - } - - /* Call the Error call Back in case of Errors */ - if (hcan->ErrorCode != HAL_CAN_ERROR_NONE) - { - /* Clear ERRI Flag */ - hcan->Instance->MSR = CAN_MSR_ERRI; - /* Set the CAN state ready to be able to start again the process */ - hcan->State = HAL_CAN_STATE_READY; - /* Call Error callback function */ - HAL_CAN_ErrorCallback(hcan); - } -} - -/** - * @brief Transmission complete callback in non blocking mode - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @retval None - */ -__weak void HAL_CAN_TxCpltCallback(CAN_HandleTypeDef* hcan) -{ - /* Prevent unused argument(s) compilation warning */ - UNUSED(hcan); - /* NOTE : This function Should not be modified, when the callback is needed, - the HAL_CAN_TxCpltCallback could be implemented in the user file - */ -} - -/** - * @brief Transmission complete callback in non blocking mode - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @retval None - */ -__weak void HAL_CAN_RxCpltCallback(CAN_HandleTypeDef* hcan) -{ - /* Prevent unused argument(s) compilation warning */ - UNUSED(hcan); - /* NOTE : This function Should not be modified, when the callback is needed, - the HAL_CAN_RxCpltCallback could be implemented in the user file - */ -} - -/** - * @brief Error CAN callback. - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @retval None - */ -__weak void HAL_CAN_ErrorCallback(CAN_HandleTypeDef* hcan) -{ - /* Prevent unused argument(s) compilation warning */ - UNUSED(hcan); - /* NOTE : This function Should not be modified, when the callback is needed, - the HAL_CAN_ErrorCallback could be implemented in the user file - */ -} - -/** - * @} - */ - -/** @defgroup CAN_Exported_Functions_Group3 Peripheral State and Error functions - * @brief CAN Peripheral State functions - * -@verbatim - ============================================================================== - ##### Peripheral State and Error functions ##### - ============================================================================== - [..] - This subsection provides functions allowing to : - (+) Check the CAN state. - (+) Check CAN Errors detected during interrupt process - -@endverbatim - * @{ - */ - -/** - * @brief return the CAN state - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @retval HAL state - */ -HAL_CAN_StateTypeDef HAL_CAN_GetState(CAN_HandleTypeDef* hcan) -{ - /* Return CAN state */ - return hcan->State; -} - -/** - * @brief Return the CAN error code - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @retval CAN Error Code - */ -uint32_t HAL_CAN_GetError(CAN_HandleTypeDef* hcan) -{ - return hcan->ErrorCode; -} - -/** - * @} - */ -/** - * @brief Initiates and transmits a CAN frame message. - * @param hcan: pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @retval HAL status - */ -static HAL_StatusTypeDef CAN_Transmit_IT(CAN_HandleTypeDef* hcan) -{ - /* Disable Transmit mailbox empty Interrupt */ - __HAL_CAN_DISABLE_IT(hcan, CAN_IT_TME); - - if (hcan->State == HAL_CAN_STATE_BUSY_TX) - { - /* Disable Error warning Interrupt */ - __HAL_CAN_DISABLE_IT(hcan, CAN_IT_EWG); - /* Disable Error passive Interrupt */ - __HAL_CAN_DISABLE_IT(hcan, CAN_IT_EPV); - /* Disable Bus-off Interrupt */ - __HAL_CAN_DISABLE_IT(hcan, CAN_IT_BOF); - /* Disable Last error code Interrupt */ - __HAL_CAN_DISABLE_IT(hcan, CAN_IT_LEC); - /* Disable Error Interrupt */ - __HAL_CAN_DISABLE_IT(hcan, CAN_IT_ERR); - } - - if (hcan->State == HAL_CAN_STATE_BUSY_TX_RX) - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_BUSY_RX; - } - else - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_READY; - } - - /* Transmission complete callback */ - HAL_CAN_TxCpltCallback(hcan); - return HAL_OK; -} - -/** - * @brief Receives a correct CAN frame. - * @param hcan: Pointer to a CAN_HandleTypeDef structure that contains - * the configuration information for the specified CAN. - * @param FIFONumber: Specify the FIFO number - * @retval HAL status - * @retval None - */ -static HAL_StatusTypeDef CAN_Receive_IT(CAN_HandleTypeDef* hcan, uint8_t FIFONumber) -{ - /* Get the Id */ - hcan->pRxMsg->IDE = (uint8_t)0x04U & hcan->Instance->sFIFOMailBox[FIFONumber].RIR; - - if (hcan->pRxMsg->IDE == CAN_ID_STD) - { - hcan->pRxMsg->StdId = (uint32_t)0x000007FFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RIR >> 21U); - } - else - { - hcan->pRxMsg->ExtId = (uint32_t)0x1FFFFFFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RIR >> 3U); - } - - hcan->pRxMsg->RTR = (uint8_t)0x02U & hcan->Instance->sFIFOMailBox[FIFONumber].RIR; - /* Get the DLC */ - hcan->pRxMsg->DLC = (uint8_t)0x0FU & hcan->Instance->sFIFOMailBox[FIFONumber].RDTR; - /* Get the FMI */ - hcan->pRxMsg->FMI = (uint8_t)0xFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RDTR >> 8U); - /* Get the data field */ - hcan->pRxMsg->Data[0U] = (uint8_t)0xFFU & hcan->Instance->sFIFOMailBox[FIFONumber].RDLR; - hcan->pRxMsg->Data[1U] = (uint8_t)0xFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RDLR >> 8U); - hcan->pRxMsg->Data[2U] = (uint8_t)0xFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RDLR >> 16U); - hcan->pRxMsg->Data[3U] = (uint8_t)0xFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RDLR >> 24U); - hcan->pRxMsg->Data[4U] = (uint8_t)0xFFU & hcan->Instance->sFIFOMailBox[FIFONumber].RDHR; - hcan->pRxMsg->Data[5U] = (uint8_t)0xFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RDHR >> 8U); - hcan->pRxMsg->Data[6U] = (uint8_t)0xFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RDHR >> 16U); - hcan->pRxMsg->Data[7U] = (uint8_t)0xFFU & (hcan->Instance->sFIFOMailBox[FIFONumber].RDHR >> 24U); - - /* Release the FIFO */ - /* Release FIFO0 */ - if (FIFONumber == CAN_FIFO0) - { - __HAL_CAN_FIFO_RELEASE(hcan, CAN_FIFO0); - /* Disable FIFO 0 message pending Interrupt */ - __HAL_CAN_DISABLE_IT(hcan, CAN_IT_FMP0); - } - /* Release FIFO1 */ - else /* FIFONumber == CAN_FIFO1 */ - { - __HAL_CAN_FIFO_RELEASE(hcan, CAN_FIFO1); - /* Disable FIFO 1 message pending Interrupt */ - __HAL_CAN_DISABLE_IT(hcan, CAN_IT_FMP1); - } - - if (hcan->State == HAL_CAN_STATE_BUSY_RX) - { - /* Disable Error warning Interrupt */ - __HAL_CAN_DISABLE_IT(hcan, CAN_IT_EWG); - /* Disable Error passive Interrupt */ - __HAL_CAN_DISABLE_IT(hcan, CAN_IT_EPV); - /* Disable Bus-off Interrupt */ - __HAL_CAN_DISABLE_IT(hcan, CAN_IT_BOF); - /* Disable Last error code Interrupt */ - __HAL_CAN_DISABLE_IT(hcan, CAN_IT_LEC); - /* Disable Error Interrupt */ - __HAL_CAN_DISABLE_IT(hcan, CAN_IT_ERR); - } - - if (hcan->State == HAL_CAN_STATE_BUSY_TX_RX) - { - /* Disable CAN state */ - hcan->State = HAL_CAN_STATE_BUSY_TX; - } - else - { - /* Change CAN state */ - hcan->State = HAL_CAN_STATE_READY; - } - - /* Receive complete callback */ - HAL_CAN_RxCpltCallback(hcan); - /* Return function status */ - return HAL_OK; -} - -/** - * @} - */ -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\ - STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx ||\ - STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#endif /* HAL_CAN_MODULE_ENABLED */ -/** - * @} - */ - -/** - * @} - */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma.c b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma.c deleted file mode 100644 index 58152df7..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma.c +++ /dev/null @@ -1,1242 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_dma.c - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief DMA HAL module driver. - * - * This file provides firmware functions to manage the following - * functionalities of the Direct Memory Access (DMA) peripheral: - * + Initialization and de-initialization functions - * + IO operation functions - * + Peripheral State and errors functions - @verbatim - ============================================================================== - ##### How to use this driver ##### - ============================================================================== - [..] - (#) Enable and configure the peripheral to be connected to the DMA Stream - (except for internal SRAM/FLASH memories: no initialization is - necessary) please refer to Reference manual for connection between peripherals - and DMA requests . - - (#) For a given Stream, program the required configuration through the following parameters: - Transfer Direction, Source and Destination data formats, - Circular, Normal or peripheral flow control mode, Stream Priority level, - Source and Destination Increment mode, FIFO mode and its Threshold (if needed), - Burst mode for Source and/or Destination (if needed) using HAL_DMA_Init() function. - - *** Polling mode IO operation *** - ================================= - [..] - (+) Use HAL_DMA_Start() to start DMA transfer after the configuration of Source - address and destination address and the Length of data to be transferred - (+) Use HAL_DMA_PollForTransfer() to poll for the end of current transfer, in this - case a fixed Timeout can be configured by User depending from his application. - - *** Interrupt mode IO operation *** - =================================== - [..] - (+) Configure the DMA interrupt priority using HAL_NVIC_SetPriority() - (+) Enable the DMA IRQ handler using HAL_NVIC_EnableIRQ() - (+) Use HAL_DMA_Start_IT() to start DMA transfer after the configuration of - Source address and destination address and the Length of data to be transferred. In this - case the DMA interrupt is configured - (+) Use HAL_DMA_IRQHandler() called under DMA_IRQHandler() Interrupt subroutine - (+) At the end of data transfer HAL_DMA_IRQHandler() function is executed and user can - add his own function by customization of function pointer XferCpltCallback and - XferErrorCallback (i.e a member of DMA handle structure). - [..] - (#) Use HAL_DMA_GetState() function to return the DMA state and HAL_DMA_GetError() in case of error - detection. - - (#) Use HAL_DMA_Abort() function to abort the current transfer - - -@- In Memory-to-Memory transfer mode, Circular mode is not allowed. - - -@- The FIFO is used mainly to reduce bus usage and to allow data packing/unpacking: it is - possible to set different Data Sizes for the Peripheral and the Memory (ie. you can set - Half-Word data size for the peripheral to access its data register and set Word data size - for the Memory to gain in access time. Each two half words will be packed and written in - a single access to a Word in the Memory). - - -@- When FIFO is disabled, it is not allowed to configure different Data Sizes for Source - and Destination. In this case the Peripheral Data Size will be applied to both Source - and Destination. - - *** DMA HAL driver macros list *** - ============================================= - [..] - Below the list of most used macros in DMA HAL driver. - - (+) __HAL_DMA_ENABLE: Enable the specified DMA Stream. - (+) __HAL_DMA_DISABLE: Disable the specified DMA Stream. - (+) __HAL_DMA_GET_FS: Return the current DMA Stream FIFO filled level. - (+) __HAL_DMA_ENABLE_IT: Enable the specified DMA Stream interrupts. - (+) __HAL_DMA_DISABLE_IT: Disable the specified DMA Stream interrupts. - (+) __HAL_DMA_GET_IT_SOURCE: Check whether the specified DMA Stream interrupt has occurred or not. - - [..] - (@) You can refer to the DMA HAL driver header file for more useful macros - - @endverbatim - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @defgroup DMA DMA - * @brief DMA HAL module driver - * @{ - */ - -#ifdef HAL_DMA_MODULE_ENABLED - -/* Private types -------------------------------------------------------------*/ -typedef struct -{ - __IO uint32_t ISR; /*!< DMA interrupt status register */ - __IO uint32_t Reserved0; - __IO uint32_t IFCR; /*!< DMA interrupt flag clear register */ -} DMA_Base_Registers; - -/* Private variables ---------------------------------------------------------*/ -/* Private constants ---------------------------------------------------------*/ -/** @addtogroup DMA_Private_Constants - * @{ - */ -#define HAL_TIMEOUT_DMA_ABORT ((uint32_t)5) /* 5 ms */ -/** - * @} - */ -/* Private macros ------------------------------------------------------------*/ -/* Private functions ---------------------------------------------------------*/ -/** @addtogroup DMA_Private_Functions - * @{ - */ -static void DMA_SetConfig(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength); -static uint32_t DMA_CalcBaseAndBitshift(DMA_HandleTypeDef* hdma); -static HAL_StatusTypeDef DMA_CheckFifoParam(DMA_HandleTypeDef* hdma); - -/** - * @} - */ - -/* Exported functions --------------------------------------------------------*/ -/** @addtogroup DMA_Exported_Functions - * @{ - */ - -/** @addtogroup DMA_Exported_Functions_Group1 - * -@verbatim - =============================================================================== - ##### Initialization and de-initialization functions ##### - =============================================================================== - [..] - This section provides functions allowing to initialize the DMA Stream source - and destination addresses, incrementation and data sizes, transfer direction, - circular/normal mode selection, memory-to-memory mode selection and Stream priority value. - [..] - The HAL_DMA_Init() function follows the DMA configuration procedures as described in - reference manual. - -@endverbatim - * @{ - */ - -/** - * @brief Initializes the DMA according to the specified - * parameters in the DMA_InitTypeDef and create the associated handle. - * @param hdma: Pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_DMA_Init(DMA_HandleTypeDef* hdma) -{ - uint32_t tmp = 0U; - uint32_t tickstart = HAL_GetTick(); - DMA_Base_Registers* regs; - - /* Check the DMA peripheral state */ - if (hdma == NULL) - { - return HAL_ERROR; - } - - /* Check the parameters */ - assert_param(IS_DMA_STREAM_ALL_INSTANCE(hdma->Instance)); - assert_param(IS_DMA_CHANNEL(hdma->Init.Channel)); - assert_param(IS_DMA_DIRECTION(hdma->Init.Direction)); - assert_param(IS_DMA_PERIPHERAL_INC_STATE(hdma->Init.PeriphInc)); - assert_param(IS_DMA_MEMORY_INC_STATE(hdma->Init.MemInc)); - assert_param(IS_DMA_PERIPHERAL_DATA_SIZE(hdma->Init.PeriphDataAlignment)); - assert_param(IS_DMA_MEMORY_DATA_SIZE(hdma->Init.MemDataAlignment)); - assert_param(IS_DMA_MODE(hdma->Init.Mode)); - assert_param(IS_DMA_PRIORITY(hdma->Init.Priority)); - assert_param(IS_DMA_FIFO_MODE_STATE(hdma->Init.FIFOMode)); - - /* Check the memory burst, peripheral burst and FIFO threshold parameters only - when FIFO mode is enabled */ - if (hdma->Init.FIFOMode != DMA_FIFOMODE_DISABLE) - { - assert_param(IS_DMA_FIFO_THRESHOLD(hdma->Init.FIFOThreshold)); - assert_param(IS_DMA_MEMORY_BURST(hdma->Init.MemBurst)); - assert_param(IS_DMA_PERIPHERAL_BURST(hdma->Init.PeriphBurst)); - } - - /* Allocate lock resource */ - __HAL_UNLOCK(hdma); - /* Change DMA peripheral state */ - hdma->State = HAL_DMA_STATE_BUSY; - /* Disable the peripheral */ - __HAL_DMA_DISABLE(hdma); - - /* Check if the DMA Stream is effectively disabled */ - while ((hdma->Instance->CR & DMA_SxCR_EN) != RESET) - { - /* Check for the Timeout */ - if ((HAL_GetTick() - tickstart ) > HAL_TIMEOUT_DMA_ABORT) - { - /* Update error code */ - hdma->ErrorCode = HAL_DMA_ERROR_TIMEOUT; - /* Change the DMA state */ - hdma->State = HAL_DMA_STATE_TIMEOUT; - return HAL_TIMEOUT; - } - } - - /* Get the CR register value */ - tmp = hdma->Instance->CR; - /* Clear CHSEL, MBURST, PBURST, PL, MSIZE, PSIZE, MINC, PINC, CIRC, DIR, CT and DBM bits */ - tmp &= ((uint32_t)~(DMA_SxCR_CHSEL | DMA_SxCR_MBURST | DMA_SxCR_PBURST | \ - DMA_SxCR_PL | DMA_SxCR_MSIZE | DMA_SxCR_PSIZE | \ - DMA_SxCR_MINC | DMA_SxCR_PINC | DMA_SxCR_CIRC | \ - DMA_SxCR_DIR | DMA_SxCR_CT | DMA_SxCR_DBM)); - /* Prepare the DMA Stream configuration */ - tmp |= hdma->Init.Channel | hdma->Init.Direction | - hdma->Init.PeriphInc | hdma->Init.MemInc | - hdma->Init.PeriphDataAlignment | hdma->Init.MemDataAlignment | - hdma->Init.Mode | hdma->Init.Priority; - - /* the Memory burst and peripheral burst are not used when the FIFO is disabled */ - if (hdma->Init.FIFOMode == DMA_FIFOMODE_ENABLE) - { - /* Get memory burst and peripheral burst */ - tmp |= hdma->Init.MemBurst | hdma->Init.PeriphBurst; - } - - /* Write to DMA Stream CR register */ - hdma->Instance->CR = tmp; - /* Get the FCR register value */ - tmp = hdma->Instance->FCR; - /* Clear Direct mode and FIFO threshold bits */ - tmp &= (uint32_t)~(DMA_SxFCR_DMDIS | DMA_SxFCR_FTH); - /* Prepare the DMA Stream FIFO configuration */ - tmp |= hdma->Init.FIFOMode; - - /* the FIFO threshold is not used when the FIFO mode is disabled */ - if (hdma->Init.FIFOMode == DMA_FIFOMODE_ENABLE) - { - /* Get the FIFO threshold */ - tmp |= hdma->Init.FIFOThreshold; - - if (DMA_CheckFifoParam(hdma) != HAL_OK) - { - /* Update error code */ - hdma->ErrorCode = HAL_DMA_ERROR_PARAM; - /* Change the DMA state */ - hdma->State = HAL_DMA_STATE_READY; - return HAL_ERROR; - } - } - - /* Write to DMA Stream FCR */ - hdma->Instance->FCR = tmp; - /* Initialize StreamBaseAddress and StreamIndex parameters to be used to calculate - DMA steam Base Address needed by HAL_DMA_IRQHandler() and HAL_DMA_PollForTransfer() */ - regs = (DMA_Base_Registers*)DMA_CalcBaseAndBitshift(hdma); - /* Clear all interrupt flags */ - regs->IFCR = 0x3FU << hdma->StreamIndex; - /* Initialize the error code */ - hdma->ErrorCode = HAL_DMA_ERROR_NONE; - /* Initialize the DMA state */ - hdma->State = HAL_DMA_STATE_READY; - return HAL_OK; -} - -/** - * @brief DeInitializes the DMA peripheral - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_DMA_DeInit(DMA_HandleTypeDef* hdma) -{ - DMA_Base_Registers* regs; - - /* Check the DMA peripheral state */ - if (hdma == NULL) - { - return HAL_ERROR; - } - - /* Check the DMA peripheral state */ - if (hdma->State == HAL_DMA_STATE_BUSY) - { - /* Return error status */ - return HAL_BUSY; - } - - /* Disable the selected DMA Streamx */ - __HAL_DMA_DISABLE(hdma); - /* Reset DMA Streamx control register */ - hdma->Instance->CR = 0U; - /* Reset DMA Streamx number of data to transfer register */ - hdma->Instance->NDTR = 0U; - /* Reset DMA Streamx peripheral address register */ - hdma->Instance->PAR = 0U; - /* Reset DMA Streamx memory 0 address register */ - hdma->Instance->M0AR = 0U; - /* Reset DMA Streamx memory 1 address register */ - hdma->Instance->M1AR = 0U; - /* Reset DMA Streamx FIFO control register */ - hdma->Instance->FCR = (uint32_t)0x00000021U; - /* Get DMA steam Base Address */ - regs = (DMA_Base_Registers*)DMA_CalcBaseAndBitshift(hdma); - /* Clear all interrupt flags at correct offset within the register */ - regs->IFCR = 0x3FU << hdma->StreamIndex; - /* Initialize the error code */ - hdma->ErrorCode = HAL_DMA_ERROR_NONE; - /* Initialize the DMA state */ - hdma->State = HAL_DMA_STATE_RESET; - /* Release Lock */ - __HAL_UNLOCK(hdma); - return HAL_OK; -} - -/** - * @} - */ - -/** @addtogroup DMA_Exported_Functions_Group2 - * -@verbatim - =============================================================================== - ##### IO operation functions ##### - =============================================================================== - [..] This section provides functions allowing to: - (+) Configure the source, destination address and data length and Start DMA transfer - (+) Configure the source, destination address and data length and - Start DMA transfer with interrupt - (+) Abort DMA transfer - (+) Poll for transfer complete - (+) Handle DMA interrupt request - -@endverbatim - * @{ - */ - -/** - * @brief Starts the DMA Transfer. - * @param hdma : pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @param SrcAddress: The source memory Buffer address - * @param DstAddress: The destination memory Buffer address - * @param DataLength: The length of data to be transferred from source to destination - * @retval HAL status - */ -HAL_StatusTypeDef HAL_DMA_Start(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Check the parameters */ - assert_param(IS_DMA_BUFFER_SIZE(DataLength)); - /* Process locked */ - __HAL_LOCK(hdma); - - if (HAL_DMA_STATE_READY == hdma->State) - { - /* Change DMA peripheral state */ - hdma->State = HAL_DMA_STATE_BUSY; - /* Initialize the error code */ - hdma->ErrorCode = HAL_DMA_ERROR_NONE; - /* Configure the source, destination address and the data length */ - DMA_SetConfig(hdma, SrcAddress, DstAddress, DataLength); - /* Enable the Peripheral */ - __HAL_DMA_ENABLE(hdma); - } - else - { - /* Process unlocked */ - __HAL_UNLOCK(hdma); - /* Return error status */ - status = HAL_BUSY; - } - - return status; -} - -/** - * @brief Starts the DMA Transfer with interrupt enabled. - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @param SrcAddress: The source memory Buffer address - * @param DstAddress: The destination memory Buffer address - * @param DataLength: The length of data to be transferred from source to destination - * @retval HAL status - */ -HAL_StatusTypeDef HAL_DMA_Start_IT(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength) -{ - HAL_StatusTypeDef status = HAL_OK; - /* calculate DMA base and stream number */ - DMA_Base_Registers* regs = (DMA_Base_Registers*)hdma->StreamBaseAddress; - /* Check the parameters */ - assert_param(IS_DMA_BUFFER_SIZE(DataLength)); - /* Process locked */ - __HAL_LOCK(hdma); - - if (HAL_DMA_STATE_READY == hdma->State) - { - /* Change DMA peripheral state */ - hdma->State = HAL_DMA_STATE_BUSY; - /* Initialize the error code */ - hdma->ErrorCode = HAL_DMA_ERROR_NONE; - /* Configure the source, destination address and the data length */ - DMA_SetConfig(hdma, SrcAddress, DstAddress, DataLength); - /* Clear all interrupt flags at correct offset within the register */ - regs->IFCR = 0x3FU << hdma->StreamIndex; - /* Enable Common interrupts*/ - hdma->Instance->CR |= DMA_IT_TC | DMA_IT_TE | DMA_IT_DME; - hdma->Instance->FCR |= DMA_IT_FE; - - if (hdma->XferHalfCpltCallback != NULL) - { - hdma->Instance->CR |= DMA_IT_HT; - } - - /* Enable the Peripheral */ - __HAL_DMA_ENABLE(hdma); - } - else - { - /* Process unlocked */ - __HAL_UNLOCK(hdma); - /* Return error status */ - status = HAL_BUSY; - } - - return status; -} - -/** - * @brief Aborts the DMA Transfer. - * @param hdma : pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * - * @note After disabling a DMA Stream, a check for wait until the DMA Stream is - * effectively disabled is added. If a Stream is disabled - * while a data transfer is ongoing, the current data will be transferred - * and the Stream will be effectively disabled only after the transfer of - * this single data is finished. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_DMA_Abort(DMA_HandleTypeDef* hdma) -{ - /* calculate DMA base and stream number */ - DMA_Base_Registers* regs = (DMA_Base_Registers*)hdma->StreamBaseAddress; - uint32_t tickstart = HAL_GetTick(); - - if (hdma->State != HAL_DMA_STATE_BUSY) - { - hdma->ErrorCode = HAL_DMA_ERROR_NO_XFER; - /* Process Unlocked */ - __HAL_UNLOCK(hdma); - return HAL_ERROR; - } - else - { - /* Disable all the transfer interrupts */ - hdma->Instance->CR &= ~(DMA_IT_TC | DMA_IT_TE | DMA_IT_DME); - hdma->Instance->FCR &= ~(DMA_IT_FE); - - if ((hdma->XferHalfCpltCallback != NULL) || (hdma->XferM1HalfCpltCallback != NULL)) - { - hdma->Instance->CR &= ~(DMA_IT_HT); - } - - /* Disable the stream */ - __HAL_DMA_DISABLE(hdma); - - /* Check if the DMA Stream is effectively disabled */ - while ((hdma->Instance->CR & DMA_SxCR_EN) != RESET) - { - /* Check for the Timeout */ - if ((HAL_GetTick() - tickstart ) > HAL_TIMEOUT_DMA_ABORT) - { - /* Update error code */ - hdma->ErrorCode = HAL_DMA_ERROR_TIMEOUT; - /* Process Unlocked */ - __HAL_UNLOCK(hdma); - /* Change the DMA state */ - hdma->State = HAL_DMA_STATE_TIMEOUT; - return HAL_TIMEOUT; - } - } - - /* Clear all interrupt flags at correct offset within the register */ - regs->IFCR = 0x3FU << hdma->StreamIndex; - /* Process Unlocked */ - __HAL_UNLOCK(hdma); - /* Change the DMA state*/ - hdma->State = HAL_DMA_STATE_READY; - } - - return HAL_OK; -} - -/** - * @brief Aborts the DMA Transfer in Interrupt mode. - * @param hdma : pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_DMA_Abort_IT(DMA_HandleTypeDef* hdma) -{ - if (hdma->State != HAL_DMA_STATE_BUSY) - { - hdma->ErrorCode = HAL_DMA_ERROR_NO_XFER; - return HAL_ERROR; - } - else - { - /* Set Abort State */ - hdma->State = HAL_DMA_STATE_ABORT; - /* Disable the stream */ - __HAL_DMA_DISABLE(hdma); - } - - return HAL_OK; -} - -/** - * @brief Polling for transfer complete. - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @param CompleteLevel: Specifies the DMA level complete. - * @note The polling mode is kept in this version for legacy. it is recommanded to use the IT model instead. - * This model could be used for debug purpose. - * @note The HAL_DMA_PollForTransfer API cannot be used in circular and double buffering mode (automatic circular mode). - * @param Timeout: Timeout duration. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_DMA_PollForTransfer(DMA_HandleTypeDef* hdma, HAL_DMA_LevelCompleteTypeDef CompleteLevel, uint32_t Timeout) -{ - HAL_StatusTypeDef status = HAL_OK; - uint32_t temp; - uint32_t tickstart = HAL_GetTick(); - uint32_t tmpisr; - /* calculate DMA base and stream number */ - DMA_Base_Registers* regs; - - /* Polling mode not supported in circular mode and double buffering mode */ - if ((hdma->Instance->CR & DMA_SxCR_CIRC) != RESET) - { - hdma->ErrorCode = HAL_DMA_ERROR_NOT_SUPPORTED; - return HAL_ERROR; - } - - /* Get the level transfer complete flag */ - if (CompleteLevel == HAL_DMA_FULL_TRANSFER) - { - /* Transfer Complete flag */ - temp = DMA_FLAG_TCIF0_4 << hdma->StreamIndex; - } - else - { - /* Half Transfer Complete flag */ - temp = DMA_FLAG_HTIF0_4 << hdma->StreamIndex; - } - - regs = (DMA_Base_Registers*)hdma->StreamBaseAddress; - tmpisr = regs->ISR; - - while ((tmpisr & temp) == RESET ) - { - /* Check for the Timeout (Not applicable in circular mode)*/ - if (Timeout != HAL_MAX_DELAY) - { - if ((Timeout == 0) || ((HAL_GetTick() - tickstart ) > Timeout)) - { - /* Update error code */ - hdma->ErrorCode = HAL_DMA_ERROR_TIMEOUT; - /* Process Unlocked */ - __HAL_UNLOCK(hdma); - /* Change the DMA state */ - hdma->State = HAL_DMA_STATE_READY; - return HAL_TIMEOUT; - } - } - - if ((tmpisr & (DMA_FLAG_TEIF0_4 << hdma->StreamIndex)) != RESET) - { - /* Update error code */ - hdma->ErrorCode |= HAL_DMA_ERROR_TE; - /* Clear the transfer error flag */ - regs->IFCR = DMA_FLAG_TEIF0_4 << hdma->StreamIndex; - } - - if ((tmpisr & (DMA_FLAG_FEIF0_4 << hdma->StreamIndex)) != RESET) - { - /* Update error code */ - hdma->ErrorCode |= HAL_DMA_ERROR_FE; - /* Clear the FIFO error flag */ - regs->IFCR = DMA_FLAG_FEIF0_4 << hdma->StreamIndex; - } - - if ((tmpisr & (DMA_FLAG_DMEIF0_4 << hdma->StreamIndex)) != RESET) - { - /* Update error code */ - hdma->ErrorCode |= HAL_DMA_ERROR_DME; - /* Clear the Direct Mode error flag */ - regs->IFCR = DMA_FLAG_DMEIF0_4 << hdma->StreamIndex; - } - } - - if (hdma->ErrorCode != HAL_DMA_ERROR_NONE) - { - if ((hdma->ErrorCode & HAL_DMA_ERROR_TE) != RESET) - { - HAL_DMA_Abort(hdma); - /* Clear the half transfer and transfer complete flags */ - regs->IFCR = (DMA_FLAG_HTIF0_4 | DMA_FLAG_TCIF0_4) << hdma->StreamIndex; - /* Process Unlocked */ - __HAL_UNLOCK(hdma); - /* Change the DMA state */ - hdma->State = HAL_DMA_STATE_READY; - return HAL_ERROR; - } - - status = HAL_ERROR; - } - - /* Get the level transfer complete flag */ - if (CompleteLevel == HAL_DMA_FULL_TRANSFER) - { - /* Clear the half transfer and transfer complete flags */ - regs->IFCR = (DMA_FLAG_HTIF0_4 | DMA_FLAG_TCIF0_4) << hdma->StreamIndex; - /* Process Unlocked */ - __HAL_UNLOCK(hdma); - hdma->State = HAL_DMA_STATE_READY; - } - else - { - /* Clear the half transfer and transfer complete flags */ - regs->IFCR = (DMA_FLAG_HTIF0_4) << hdma->StreamIndex; - } - - return status; -} - -/** - * @brief Handles DMA interrupt request. - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @retval None - */ -void HAL_DMA_IRQHandler(DMA_HandleTypeDef* hdma) -{ - uint32_t tmpisr; - __IO uint32_t count = 0; - uint32_t timeout = SystemCoreClock / 9600; - /* calculate DMA base and stream number */ - DMA_Base_Registers* regs = (DMA_Base_Registers*)hdma->StreamBaseAddress; - tmpisr = regs->ISR; - - /* Transfer Error Interrupt management ***************************************/ - if ((tmpisr & (DMA_FLAG_TEIF0_4 << hdma->StreamIndex)) != RESET) - { - if (__HAL_DMA_GET_IT_SOURCE(hdma, DMA_IT_TE) != RESET) - { - /* Disable the transfer error interrupt */ - hdma->Instance->CR &= ~(DMA_IT_TE); - /* Clear the transfer error flag */ - regs->IFCR = DMA_FLAG_TEIF0_4 << hdma->StreamIndex; - /* Update error code */ - hdma->ErrorCode |= HAL_DMA_ERROR_TE; - } - } - - /* FIFO Error Interrupt management ******************************************/ - if ((tmpisr & (DMA_FLAG_FEIF0_4 << hdma->StreamIndex)) != RESET) - { - if (__HAL_DMA_GET_IT_SOURCE(hdma, DMA_IT_FE) != RESET) - { - /* Clear the FIFO error flag */ - regs->IFCR = DMA_FLAG_FEIF0_4 << hdma->StreamIndex; - /* Update error code */ - hdma->ErrorCode |= HAL_DMA_ERROR_FE; - } - } - - /* Direct Mode Error Interrupt management ***********************************/ - if ((tmpisr & (DMA_FLAG_DMEIF0_4 << hdma->StreamIndex)) != RESET) - { - if (__HAL_DMA_GET_IT_SOURCE(hdma, DMA_IT_DME) != RESET) - { - /* Clear the direct mode error flag */ - regs->IFCR = DMA_FLAG_DMEIF0_4 << hdma->StreamIndex; - /* Update error code */ - hdma->ErrorCode |= HAL_DMA_ERROR_DME; - } - } - - /* Half Transfer Complete Interrupt management ******************************/ - if ((tmpisr & (DMA_FLAG_HTIF0_4 << hdma->StreamIndex)) != RESET) - { - if (__HAL_DMA_GET_IT_SOURCE(hdma, DMA_IT_HT) != RESET) - { - /* Clear the half transfer complete flag */ - regs->IFCR = DMA_FLAG_HTIF0_4 << hdma->StreamIndex; - - /* Multi_Buffering mode enabled */ - if (((hdma->Instance->CR) & (uint32_t)(DMA_SxCR_DBM)) != RESET) - { - /* Current memory buffer used is Memory 0 */ - if ((hdma->Instance->CR & DMA_SxCR_CT) == RESET) - { - if (hdma->XferHalfCpltCallback != NULL) - { - /* Half transfer callback */ - hdma->XferHalfCpltCallback(hdma); - } - } - /* Current memory buffer used is Memory 1 */ - else - { - if (hdma->XferM1HalfCpltCallback != NULL) - { - /* Half transfer callback */ - hdma->XferM1HalfCpltCallback(hdma); - } - } - } - else - { - /* Disable the half transfer interrupt if the DMA mode is not CIRCULAR */ - if ((hdma->Instance->CR & DMA_SxCR_CIRC) == RESET) - { - /* Disable the half transfer interrupt */ - hdma->Instance->CR &= ~(DMA_IT_HT); - } - - if (hdma->XferHalfCpltCallback != NULL) - { - /* Half transfer callback */ - hdma->XferHalfCpltCallback(hdma); - } - } - } - } - - /* Transfer Complete Interrupt management ***********************************/ - if ((tmpisr & (DMA_FLAG_TCIF0_4 << hdma->StreamIndex)) != RESET) - { - if (__HAL_DMA_GET_IT_SOURCE(hdma, DMA_IT_TC) != RESET) - { - /* Clear the transfer complete flag */ - regs->IFCR = DMA_FLAG_TCIF0_4 << hdma->StreamIndex; - - if (HAL_DMA_STATE_ABORT == hdma->State) - { - /* Disable all the transfer interrupts */ - hdma->Instance->CR &= ~(DMA_IT_TC | DMA_IT_TE | DMA_IT_DME); - hdma->Instance->FCR &= ~(DMA_IT_FE); - - if ((hdma->XferHalfCpltCallback != NULL) || (hdma->XferM1HalfCpltCallback != NULL)) - { - hdma->Instance->CR &= ~(DMA_IT_HT); - } - - /* Clear all interrupt flags at correct offset within the register */ - regs->IFCR = 0x3FU << hdma->StreamIndex; - /* Process Unlocked */ - __HAL_UNLOCK(hdma); - /* Change the DMA state */ - hdma->State = HAL_DMA_STATE_READY; - - if (hdma->XferAbortCallback != NULL) - { - hdma->XferAbortCallback(hdma); - } - - return; - } - - if (((hdma->Instance->CR) & (uint32_t)(DMA_SxCR_DBM)) != RESET) - { - /* Current memory buffer used is Memory 0 */ - if ((hdma->Instance->CR & DMA_SxCR_CT) == RESET) - { - if (hdma->XferM1CpltCallback != NULL) - { - /* Transfer complete Callback for memory1 */ - hdma->XferM1CpltCallback(hdma); - } - } - /* Current memory buffer used is Memory 1 */ - else - { - if (hdma->XferCpltCallback != NULL) - { - /* Transfer complete Callback for memory0 */ - hdma->XferCpltCallback(hdma); - } - } - } - /* Disable the transfer complete interrupt if the DMA mode is not CIRCULAR */ - else - { - if ((hdma->Instance->CR & DMA_SxCR_CIRC) == RESET) - { - /* Disable the transfer complete interrupt */ - hdma->Instance->CR &= ~(DMA_IT_TC); - /* Process Unlocked */ - __HAL_UNLOCK(hdma); - /* Change the DMA state */ - hdma->State = HAL_DMA_STATE_READY; - } - - if (hdma->XferCpltCallback != NULL) - { - /* Transfer complete callback */ - hdma->XferCpltCallback(hdma); - } - } - } - } - - /* manage error case */ - if (hdma->ErrorCode != HAL_DMA_ERROR_NONE) - { - if ((hdma->ErrorCode & HAL_DMA_ERROR_TE) != RESET) - { - hdma->State = HAL_DMA_STATE_ABORT; - /* Disable the stream */ - __HAL_DMA_DISABLE(hdma); - - do - { - if (++count > timeout) - { - break; - } - } - while ((hdma->Instance->CR & DMA_SxCR_EN) != RESET); - - /* Process Unlocked */ - __HAL_UNLOCK(hdma); - /* Change the DMA state */ - hdma->State = HAL_DMA_STATE_READY; - } - - if (hdma->XferErrorCallback != NULL) - { - /* Transfer error callback */ - hdma->XferErrorCallback(hdma); - } - } -} - -/** - * @brief Register callbacks - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @param CallbackID: User Callback identifer - * a DMA_HandleTypeDef structure as parameter. - * @param pCallback: pointer to private callbacsk function which has pointer to - * a DMA_HandleTypeDef structure as parameter. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_DMA_RegisterCallback(DMA_HandleTypeDef* hdma, HAL_DMA_CallbackIDTypeDef CallbackID, void (* pCallback)(DMA_HandleTypeDef* _hdma)) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Process locked */ - __HAL_LOCK(hdma); - - if (HAL_DMA_STATE_READY == hdma->State) - { - switch (CallbackID) - { - case HAL_DMA_XFER_CPLT_CB_ID: - hdma->XferCpltCallback = pCallback; - break; - - case HAL_DMA_XFER_HALFCPLT_CB_ID: - hdma->XferHalfCpltCallback = pCallback; - break; - - case HAL_DMA_XFER_M1CPLT_CB_ID: - hdma->XferM1CpltCallback = pCallback; - break; - - case HAL_DMA_XFER_M1HALFCPLT_CB_ID: - hdma->XferM1HalfCpltCallback = pCallback; - break; - - case HAL_DMA_XFER_ERROR_CB_ID: - hdma->XferErrorCallback = pCallback; - break; - - case HAL_DMA_XFER_ABORT_CB_ID: - hdma->XferAbortCallback = pCallback; - break; - - default: - break; - } - } - else - { - /* Return error status */ - status = HAL_ERROR; - } - - /* Release Lock */ - __HAL_UNLOCK(hdma); - return status; -} - -/** - * @brief UnRegister callbacks - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @param CallbackID: User Callback identifer - * a HAL_DMA_CallbackIDTypeDef ENUM as parameter. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_DMA_UnRegisterCallback(DMA_HandleTypeDef* hdma, HAL_DMA_CallbackIDTypeDef CallbackID) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Process locked */ - __HAL_LOCK(hdma); - - if (HAL_DMA_STATE_READY == hdma->State) - { - switch (CallbackID) - { - case HAL_DMA_XFER_CPLT_CB_ID: - hdma->XferCpltCallback = NULL; - break; - - case HAL_DMA_XFER_HALFCPLT_CB_ID: - hdma->XferHalfCpltCallback = NULL; - break; - - case HAL_DMA_XFER_M1CPLT_CB_ID: - hdma->XferM1CpltCallback = NULL; - break; - - case HAL_DMA_XFER_M1HALFCPLT_CB_ID: - hdma->XferM1HalfCpltCallback = NULL; - break; - - case HAL_DMA_XFER_ERROR_CB_ID: - hdma->XferErrorCallback = NULL; - break; - - case HAL_DMA_XFER_ABORT_CB_ID: - hdma->XferAbortCallback = NULL; - break; - - case HAL_DMA_XFER_ALL_CB_ID: - hdma->XferCpltCallback = NULL; - hdma->XferHalfCpltCallback = NULL; - hdma->XferM1CpltCallback = NULL; - hdma->XferM1HalfCpltCallback = NULL; - hdma->XferErrorCallback = NULL; - hdma->XferAbortCallback = NULL; - break; - - default: - status = HAL_ERROR; - break; - } - } - else - { - status = HAL_ERROR; - } - - /* Release Lock */ - __HAL_UNLOCK(hdma); - return status; -} - -/** - * @} - */ - -/** @addtogroup DMA_Exported_Functions_Group3 - * -@verbatim - =============================================================================== - ##### State and Errors functions ##### - =============================================================================== - [..] - This subsection provides functions allowing to - (+) Check the DMA state - (+) Get error code - -@endverbatim - * @{ - */ - -/** - * @brief Returns the DMA state. - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @retval HAL state - */ -HAL_DMA_StateTypeDef HAL_DMA_GetState(DMA_HandleTypeDef* hdma) -{ - return hdma->State; -} - -/** - * @brief Return the DMA error code - * @param hdma : pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @retval DMA Error Code - */ -uint32_t HAL_DMA_GetError(DMA_HandleTypeDef* hdma) -{ - return hdma->ErrorCode; -} - -/** - * @} - */ - -/** - * @} - */ - -/** @addtogroup DMA_Private_Functions - * @{ - */ - -/** - * @brief Sets the DMA Transfer parameter. - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @param SrcAddress: The source memory Buffer address - * @param DstAddress: The destination memory Buffer address - * @param DataLength: The length of data to be transferred from source to destination - * @retval HAL status - */ -static void DMA_SetConfig(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength) -{ - /* Clear DBM bit */ - hdma->Instance->CR &= (uint32_t)(~DMA_SxCR_DBM); - /* Configure DMA Stream data length */ - hdma->Instance->NDTR = DataLength; - - /* Peripheral to Memory */ - if ((hdma->Init.Direction) == DMA_MEMORY_TO_PERIPH) - { - /* Configure DMA Stream destination address */ - hdma->Instance->PAR = DstAddress; - /* Configure DMA Stream source address */ - hdma->Instance->M0AR = SrcAddress; - } - /* Memory to Peripheral */ - else - { - /* Configure DMA Stream source address */ - hdma->Instance->PAR = SrcAddress; - /* Configure DMA Stream destination address */ - hdma->Instance->M0AR = DstAddress; - } -} - -/** - * @brief Returns the DMA Stream base address depending on stream number - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @retval Stream base address - */ -static uint32_t DMA_CalcBaseAndBitshift(DMA_HandleTypeDef* hdma) -{ - uint32_t stream_number = (((uint32_t)hdma->Instance & 0xFFU) - 16U) / 24U; - /* lookup table for necessary bitshift of flags within status registers */ - static const uint8_t flagBitshiftOffset[8U] = {0U, 6U, 16U, 22U, 0U, 6U, 16U, 22U}; - hdma->StreamIndex = flagBitshiftOffset[stream_number]; - - if (stream_number > 3U) - { - /* return pointer to HISR and HIFCR */ - hdma->StreamBaseAddress = (((uint32_t)hdma->Instance & (uint32_t)(~0x3FFU)) + 4U); - } - else - { - /* return pointer to LISR and LIFCR */ - hdma->StreamBaseAddress = ((uint32_t)hdma->Instance & (uint32_t)(~0x3FFU)); - } - - return hdma->StreamBaseAddress; -} - -/** - * @brief Checks compatibility between FIFO threshold level and size of the memory burst - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @retval HAL status - */ -static HAL_StatusTypeDef DMA_CheckFifoParam(DMA_HandleTypeDef* hdma) -{ - HAL_StatusTypeDef status = HAL_OK; - uint32_t tmp = hdma->Init.FIFOThreshold; - - /* Memory Data size equal to Byte */ - if (hdma->Init.MemDataAlignment == DMA_MDATAALIGN_BYTE) - { - switch (tmp) - { - case DMA_FIFO_THRESHOLD_1QUARTERFULL: - if ((hdma->Init.MemBurst & DMA_SxCR_MBURST_1) == DMA_SxCR_MBURST_1) - { - status = HAL_ERROR; - } - - break; - - case DMA_FIFO_THRESHOLD_HALFFULL: - if (hdma->Init.MemBurst == DMA_MBURST_INC16) - { - status = HAL_ERROR; - } - - break; - - case DMA_FIFO_THRESHOLD_3QUARTERSFULL: - if ((hdma->Init.MemBurst & DMA_SxCR_MBURST_1) == DMA_SxCR_MBURST_1) - { - status = HAL_ERROR; - } - - break; - - case DMA_FIFO_THRESHOLD_FULL: - break; - - default: - break; - } - } - /* Memory Data size equal to Half-Word */ - else if (hdma->Init.MemDataAlignment == DMA_MDATAALIGN_HALFWORD) - { - switch (tmp) - { - case DMA_FIFO_THRESHOLD_1QUARTERFULL: - status = HAL_ERROR; - break; - - case DMA_FIFO_THRESHOLD_HALFFULL: - if ((hdma->Init.MemBurst & DMA_SxCR_MBURST_1) == DMA_SxCR_MBURST_1) - { - status = HAL_ERROR; - } - - break; - - case DMA_FIFO_THRESHOLD_3QUARTERSFULL: - status = HAL_ERROR; - break; - - case DMA_FIFO_THRESHOLD_FULL: - if (hdma->Init.MemBurst == DMA_MBURST_INC16) - { - status = HAL_ERROR; - } - - break; - - default: - break; - } - } - /* Memory Data size equal to Word */ - else - { - switch (tmp) - { - case DMA_FIFO_THRESHOLD_1QUARTERFULL: - case DMA_FIFO_THRESHOLD_HALFFULL: - case DMA_FIFO_THRESHOLD_3QUARTERSFULL: - status = HAL_ERROR; - break; - - case DMA_FIFO_THRESHOLD_FULL: - if ((hdma->Init.MemBurst & DMA_SxCR_MBURST_1) == DMA_SxCR_MBURST_1) - { - status = HAL_ERROR; - } - - break; - - default: - break; - } - } - - return status; -} - -/** - * @} - */ - -#endif /* HAL_DMA_MODULE_ENABLED */ -/** - * @} - */ - -/** - * @} - */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma_ex.c b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma_ex.c deleted file mode 100644 index 2d7fbae4..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma_ex.c +++ /dev/null @@ -1,320 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_dma_ex.c - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief DMA Extension HAL module driver - * This file provides firmware functions to manage the following - * functionalities of the DMA Extension peripheral: - * + Extended features functions - * - @verbatim - ============================================================================== - ##### How to use this driver ##### - ============================================================================== - [..] - The DMA Extension HAL driver can be used as follows: - (#) Start a multi buffer transfer using the HAL_DMA_MultiBufferStart() function - for polling mode or HAL_DMA_MultiBufferStart_IT() for interrupt mode. - - -@- In Memory-to-Memory transfer mode, Multi (Double) Buffer mode is not allowed. - -@- When Multi (Double) Buffer mode is enabled the, transfer is circular by default. - -@- In Multi (Double) buffer mode, it is possible to update the base address for - the AHB memory port on the fly (DMA_SxM0AR or DMA_SxM1AR) when the stream is enabled. - - @endverbatim - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @defgroup DMAEx DMAEx - * @brief DMA Extended HAL module driver - * @{ - */ - -#ifdef HAL_DMA_MODULE_ENABLED - -/* Private types -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/* Private Constants ---------------------------------------------------------*/ -/* Private macros ------------------------------------------------------------*/ -/* Private functions ---------------------------------------------------------*/ -/** @addtogroup DMAEx_Private_Functions - * @{ - */ -static void DMA_MultiBufferSetConfig(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength); -/** - * @} - */ - -/* Exported functions ---------------------------------------------------------*/ - -/** @addtogroup DMAEx_Exported_Functions - * @{ - */ - - -/** @addtogroup DMAEx_Exported_Functions_Group1 - * -@verbatim - =============================================================================== - ##### Extended features functions ##### - =============================================================================== - [..] This section provides functions allowing to: - (+) Configure the source, destination address and data length and - Start MultiBuffer DMA transfer - (+) Configure the source, destination address and data length and - Start MultiBuffer DMA transfer with interrupt - (+) Change on the fly the memory0 or memory1 address. - -@endverbatim - * @{ - */ - - -/** - * @brief Starts the multi_buffer DMA Transfer. - * @param hdma : pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @param SrcAddress: The source memory Buffer address - * @param DstAddress: The destination memory Buffer address - * @param SecondMemAddress: The second memory Buffer address in case of multi buffer Transfer - * @param DataLength: The length of data to be transferred from source to destination - * @retval HAL status - */ -HAL_StatusTypeDef HAL_DMAEx_MultiBufferStart(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t SecondMemAddress, uint32_t DataLength) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Check the parameters */ - assert_param(IS_DMA_BUFFER_SIZE(DataLength)); - - /* Memory-to-memory transfer not supported in double buffering mode */ - if (hdma->Init.Direction == DMA_MEMORY_TO_MEMORY) - { - hdma->ErrorCode = HAL_DMA_ERROR_NOT_SUPPORTED; - status = HAL_ERROR; - } - else - { - /* Process Locked */ - __HAL_LOCK(hdma); - - if (HAL_DMA_STATE_READY == hdma->State) - { - /* Change DMA peripheral state */ - hdma->State = HAL_DMA_STATE_BUSY; - /* Enable the double buffer mode */ - hdma->Instance->CR |= (uint32_t)DMA_SxCR_DBM; - /* Configure DMA Stream destination address */ - hdma->Instance->M1AR = SecondMemAddress; - /* Configure the source, destination address and the data length */ - DMA_MultiBufferSetConfig(hdma, SrcAddress, DstAddress, DataLength); - /* Enable the peripheral */ - __HAL_DMA_ENABLE(hdma); - } - else - { - /* Return error status */ - status = HAL_BUSY; - } - } - - return status; -} - -/** - * @brief Starts the multi_buffer DMA Transfer with interrupt enabled. - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @param SrcAddress: The source memory Buffer address - * @param DstAddress: The destination memory Buffer address - * @param SecondMemAddress: The second memory Buffer address in case of multi buffer Transfer - * @param DataLength: The length of data to be transferred from source to destination - * @retval HAL status - */ -HAL_StatusTypeDef HAL_DMAEx_MultiBufferStart_IT(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t SecondMemAddress, uint32_t DataLength) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Check the parameters */ - assert_param(IS_DMA_BUFFER_SIZE(DataLength)); - - /* Memory-to-memory transfer not supported in double buffering mode */ - if (hdma->Init.Direction == DMA_MEMORY_TO_MEMORY) - { - hdma->ErrorCode = HAL_DMA_ERROR_NOT_SUPPORTED; - return HAL_ERROR; - } - - /* Check callback functions */ - if ((NULL == hdma->XferCpltCallback) || (NULL == hdma->XferM1CpltCallback) || (NULL == hdma->XferErrorCallback)) - { - hdma->ErrorCode = HAL_DMA_ERROR_PARAM; - return HAL_ERROR; - } - - /* Process locked */ - __HAL_LOCK(hdma); - - if (HAL_DMA_STATE_READY == hdma->State) - { - /* Change DMA peripheral state */ - hdma->State = HAL_DMA_STATE_BUSY; - /* Initialize the error code */ - hdma->ErrorCode = HAL_DMA_ERROR_NONE; - /* Enable the Double buffer mode */ - hdma->Instance->CR |= (uint32_t)DMA_SxCR_DBM; - /* Configure DMA Stream destination address */ - hdma->Instance->M1AR = SecondMemAddress; - /* Configure the source, destination address and the data length */ - DMA_MultiBufferSetConfig(hdma, SrcAddress, DstAddress, DataLength); - /* Clear all flags */ - __HAL_DMA_CLEAR_FLAG (hdma, __HAL_DMA_GET_TC_FLAG_INDEX(hdma)); - __HAL_DMA_CLEAR_FLAG (hdma, __HAL_DMA_GET_HT_FLAG_INDEX(hdma)); - __HAL_DMA_CLEAR_FLAG (hdma, __HAL_DMA_GET_TE_FLAG_INDEX(hdma)); - __HAL_DMA_CLEAR_FLAG (hdma, __HAL_DMA_GET_DME_FLAG_INDEX(hdma)); - __HAL_DMA_CLEAR_FLAG (hdma, __HAL_DMA_GET_FE_FLAG_INDEX(hdma)); - /* Enable Common interrupts*/ - hdma->Instance->CR |= DMA_IT_TC | DMA_IT_TE | DMA_IT_DME; - hdma->Instance->FCR |= DMA_IT_FE; - - if ((hdma->XferHalfCpltCallback != NULL) || (hdma->XferM1HalfCpltCallback != NULL)) - { - hdma->Instance->CR |= DMA_IT_HT; - } - - /* Enable the peripheral */ - __HAL_DMA_ENABLE(hdma); - } - else - { - /* Process unlocked */ - __HAL_UNLOCK(hdma); - /* Return error status */ - status = HAL_BUSY; - } - - return status; -} - -/** - * @brief Change the memory0 or memory1 address on the fly. - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @param Address: The new address - * @param memory: the memory to be changed, This parameter can be one of - * the following values: - * MEMORY0 / - * MEMORY1 - * @note The MEMORY0 address can be changed only when the current transfer use - * MEMORY1 and the MEMORY1 address can be changed only when the current - * transfer use MEMORY0. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_DMAEx_ChangeMemory(DMA_HandleTypeDef* hdma, uint32_t Address, HAL_DMA_MemoryTypeDef memory) -{ - if (memory == MEMORY0) - { - /* change the memory0 address */ - hdma->Instance->M0AR = Address; - } - else - { - /* change the memory1 address */ - hdma->Instance->M1AR = Address; - } - - return HAL_OK; -} - -/** - * @} - */ - -/** - * @} - */ - -/** @addtogroup DMAEx_Private_Functions - * @{ - */ - -/** - * @brief Set the DMA Transfer parameter. - * @param hdma: pointer to a DMA_HandleTypeDef structure that contains - * the configuration information for the specified DMA Stream. - * @param SrcAddress: The source memory Buffer address - * @param DstAddress: The destination memory Buffer address - * @param DataLength: The length of data to be transferred from source to destination - * @retval HAL status - */ -static void DMA_MultiBufferSetConfig(DMA_HandleTypeDef* hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength) -{ - /* Configure DMA Stream data length */ - hdma->Instance->NDTR = DataLength; - - /* Peripheral to Memory */ - if ((hdma->Init.Direction) == DMA_MEMORY_TO_PERIPH) - { - /* Configure DMA Stream destination address */ - hdma->Instance->PAR = DstAddress; - /* Configure DMA Stream source address */ - hdma->Instance->M0AR = SrcAddress; - } - /* Memory to Peripheral */ - else - { - /* Configure DMA Stream source address */ - hdma->Instance->PAR = SrcAddress; - /* Configure DMA Stream destination address */ - hdma->Instance->M0AR = DstAddress; - } -} - -/** - * @} - */ - -#endif /* HAL_DMA_MODULE_ENABLED */ -/** - * @} - */ - -/** - * @} - */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash.c b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash.c deleted file mode 100644 index fe16ef51..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash.c +++ /dev/null @@ -1,737 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_flash.c - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief FLASH HAL module driver. - * This file provides firmware functions to manage the following - * functionalities of the internal FLASH memory: - * + Program operations functions - * + Memory Control functions - * + Peripheral Errors functions - * - @verbatim - ============================================================================== - ##### FLASH peripheral features ##### - ============================================================================== - - [..] The Flash memory interface manages CPU AHB I-Code and D-Code accesses - to the Flash memory. It implements the erase and program Flash memory operations - and the read and write protection mechanisms. - - [..] The Flash memory interface accelerates code execution with a system of instruction - prefetch and cache lines. - - [..] The FLASH main features are: - (+) Flash memory read operations - (+) Flash memory program/erase operations - (+) Read / write protections - (+) Prefetch on I-Code - (+) 64 cache lines of 128 bits on I-Code - (+) 8 cache lines of 128 bits on D-Code - - - ##### How to use this driver ##### - ============================================================================== - [..] - This driver provides functions and macros to configure and program the FLASH - memory of all STM32F4xx devices. - - (#) FLASH Memory IO Programming functions: - (++) Lock and Unlock the FLASH interface using HAL_FLASH_Unlock() and - HAL_FLASH_Lock() functions - (++) Program functions: byte, half word, word and double word - (++) There Two modes of programming : - (+++) Polling mode using HAL_FLASH_Program() function - (+++) Interrupt mode using HAL_FLASH_Program_IT() function - - (#) Interrupts and flags management functions : - (++) Handle FLASH interrupts by calling HAL_FLASH_IRQHandler() - (++) Wait for last FLASH operation according to its status - (++) Get error flag status by calling HAL_SetErrorCode() - - [..] - In addition to these functions, this driver includes a set of macros allowing - to handle the following operations: - (+) Set the latency - (+) Enable/Disable the prefetch buffer - (+) Enable/Disable the Instruction cache and the Data cache - (+) Reset the Instruction cache and the Data cache - (+) Enable/Disable the FLASH interrupts - (+) Monitor the FLASH flags status - - @endverbatim - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @defgroup FLASH FLASH - * @brief FLASH HAL module driver - * @{ - */ - -#ifdef HAL_FLASH_MODULE_ENABLED - -/* Private typedef -----------------------------------------------------------*/ -/* Private define ------------------------------------------------------------*/ -/** @addtogroup FLASH_Private_Constants - * @{ - */ -#define FLASH_TIMEOUT_VALUE ((uint32_t)50000U)/* 50 s */ -/** - * @} - */ -/* Private macro -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/** @addtogroup FLASH_Private_Variables - * @{ - */ -/* Variable used for Erase sectors under interruption */ -FLASH_ProcessTypeDef pFlash; -/** - * @} - */ - -/* Private function prototypes -----------------------------------------------*/ -/** @addtogroup FLASH_Private_Functions - * @{ - */ -/* Program operations */ -static void FLASH_Program_DoubleWord(uint32_t Address, uint64_t Data); -static void FLASH_Program_Word(uint32_t Address, uint32_t Data); -static void FLASH_Program_HalfWord(uint32_t Address, uint16_t Data); -static void FLASH_Program_Byte(uint32_t Address, uint8_t Data); -static void FLASH_SetErrorCode(void); - -HAL_StatusTypeDef FLASH_WaitForLastOperation(uint32_t Timeout); -/** - * @} - */ - -/* Exported functions --------------------------------------------------------*/ -/** @defgroup FLASH_Exported_Functions FLASH Exported Functions - * @{ - */ - -/** @defgroup FLASH_Exported_Functions_Group1 Programming operation functions - * @brief Programming operation functions - * -@verbatim - =============================================================================== - ##### Programming operation functions ##### - =============================================================================== - [..] - This subsection provides a set of functions allowing to manage the FLASH - program operations. - -@endverbatim - * @{ - */ - -/** - * @brief Program byte, halfword, word or double word at a specified address - * @param TypeProgram: Indicate the way to program at a specified address. - * This parameter can be a value of @ref FLASH_Type_Program - * @param Address: specifies the address to be programmed. - * @param Data: specifies the data to be programmed - * - * @retval HAL_StatusTypeDef HAL Status - */ -HAL_StatusTypeDef HAL_FLASH_Program(uint32_t TypeProgram, uint32_t Address, uint64_t Data) -{ - HAL_StatusTypeDef status = HAL_ERROR; - /* Process Locked */ - __HAL_LOCK(&pFlash); - /* Check the parameters */ - assert_param(IS_FLASH_TYPEPROGRAM(TypeProgram)); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - if (TypeProgram == FLASH_TYPEPROGRAM_BYTE) - { - /*Program byte (8-bit) at a specified address.*/ - FLASH_Program_Byte(Address, (uint8_t) Data); - } - else if (TypeProgram == FLASH_TYPEPROGRAM_HALFWORD) - { - /*Program halfword (16-bit) at a specified address.*/ - FLASH_Program_HalfWord(Address, (uint16_t) Data); - } - else if (TypeProgram == FLASH_TYPEPROGRAM_WORD) - { - /*Program word (32-bit) at a specified address.*/ - FLASH_Program_Word(Address, (uint32_t) Data); - } - else - { - /*Program double word (64-bit) at a specified address.*/ - FLASH_Program_DoubleWord(Address, Data); - } - - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - /* If the program operation is completed, disable the PG Bit */ - FLASH->CR &= (~FLASH_CR_PG); - } - - /* Process Unlocked */ - __HAL_UNLOCK(&pFlash); - return status; -} - -/** - * @brief Program byte, halfword, word or double word at a specified address with interrupt enabled. - * @param TypeProgram: Indicate the way to program at a specified address. - * This parameter can be a value of @ref FLASH_Type_Program - * @param Address: specifies the address to be programmed. - * @param Data: specifies the data to be programmed - * - * @retval HAL Status - */ -HAL_StatusTypeDef HAL_FLASH_Program_IT(uint32_t TypeProgram, uint32_t Address, uint64_t Data) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Process Locked */ - __HAL_LOCK(&pFlash); - /* Check the parameters */ - assert_param(IS_FLASH_TYPEPROGRAM(TypeProgram)); - /* Enable End of FLASH Operation interrupt */ - __HAL_FLASH_ENABLE_IT(FLASH_IT_EOP); - /* Enable Error source interrupt */ - __HAL_FLASH_ENABLE_IT(FLASH_IT_ERR); - pFlash.ProcedureOnGoing = FLASH_PROC_PROGRAM; - pFlash.Address = Address; - - if (TypeProgram == FLASH_TYPEPROGRAM_BYTE) - { - /*Program byte (8-bit) at a specified address.*/ - FLASH_Program_Byte(Address, (uint8_t) Data); - } - else if (TypeProgram == FLASH_TYPEPROGRAM_HALFWORD) - { - /*Program halfword (16-bit) at a specified address.*/ - FLASH_Program_HalfWord(Address, (uint16_t) Data); - } - else if (TypeProgram == FLASH_TYPEPROGRAM_WORD) - { - /*Program word (32-bit) at a specified address.*/ - FLASH_Program_Word(Address, (uint32_t) Data); - } - else - { - /*Program double word (64-bit) at a specified address.*/ - FLASH_Program_DoubleWord(Address, Data); - } - - return status; -} - -/** - * @brief This function handles FLASH interrupt request. - * @retval None - */ -void HAL_FLASH_IRQHandler(void) -{ - uint32_t addresstmp = 0U; - - /* Check FLASH operation error flags */ - if (__HAL_FLASH_GET_FLAG((FLASH_FLAG_OPERR | FLASH_FLAG_WRPERR | FLASH_FLAG_PGAERR | \ - FLASH_FLAG_PGPERR | FLASH_FLAG_PGSERR | FLASH_FLAG_RDERR)) != RESET) - { - if (pFlash.ProcedureOnGoing == FLASH_PROC_SECTERASE) - { - /*return the faulty sector*/ - addresstmp = pFlash.Sector; - pFlash.Sector = 0xFFFFFFFFU; - } - else if (pFlash.ProcedureOnGoing == FLASH_PROC_MASSERASE) - { - /*return the faulty bank*/ - addresstmp = pFlash.Bank; - } - else - { - /*return the faulty address*/ - addresstmp = pFlash.Address; - } - - /*Save the Error code*/ - FLASH_SetErrorCode(); - /* FLASH error interrupt user callback */ - HAL_FLASH_OperationErrorCallback(addresstmp); - /*Stop the procedure ongoing*/ - pFlash.ProcedureOnGoing = FLASH_PROC_NONE; - } - - /* Check FLASH End of Operation flag */ - if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_EOP) != RESET) - { - /* Clear FLASH End of Operation pending bit */ - __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP); - - if (pFlash.ProcedureOnGoing == FLASH_PROC_SECTERASE) - { - /*Nb of sector to erased can be decreased*/ - pFlash.NbSectorsToErase--; - - /* Check if there are still sectors to erase*/ - if (pFlash.NbSectorsToErase != 0U) - { - addresstmp = pFlash.Sector; - /*Indicate user which sector has been erased*/ - HAL_FLASH_EndOfOperationCallback(addresstmp); - /*Increment sector number*/ - pFlash.Sector++; - addresstmp = pFlash.Sector; - FLASH_Erase_Sector(addresstmp, pFlash.VoltageForErase); - } - else - { - /*No more sectors to Erase, user callback can be called.*/ - /*Reset Sector and stop Erase sectors procedure*/ - pFlash.Sector = addresstmp = 0xFFFFFFFFU; - pFlash.ProcedureOnGoing = FLASH_PROC_NONE; - /* Flush the caches to be sure of the data consistency */ - FLASH_FlushCaches() ; - /* FLASH EOP interrupt user callback */ - HAL_FLASH_EndOfOperationCallback(addresstmp); - } - } - else - { - if (pFlash.ProcedureOnGoing == FLASH_PROC_MASSERASE) - { - /* MassErase ended. Return the selected bank */ - /* Flush the caches to be sure of the data consistency */ - FLASH_FlushCaches() ; - /* FLASH EOP interrupt user callback */ - HAL_FLASH_EndOfOperationCallback(pFlash.Bank); - } - else - { - /*Program ended. Return the selected address*/ - /* FLASH EOP interrupt user callback */ - HAL_FLASH_EndOfOperationCallback(pFlash.Address); - } - - pFlash.ProcedureOnGoing = FLASH_PROC_NONE; - } - } - - if (pFlash.ProcedureOnGoing == FLASH_PROC_NONE) - { - /* Operation is completed, disable the PG, SER, SNB and MER Bits */ - CLEAR_BIT(FLASH->CR, (FLASH_CR_PG | FLASH_CR_SER | FLASH_CR_SNB | FLASH_MER_BIT)); - /* Disable End of FLASH Operation interrupt */ - __HAL_FLASH_DISABLE_IT(FLASH_IT_EOP); - /* Disable Error source interrupt */ - __HAL_FLASH_DISABLE_IT(FLASH_IT_ERR); - /* Process Unlocked */ - __HAL_UNLOCK(&pFlash); - } -} - -/** - * @brief FLASH end of operation interrupt callback - * @param ReturnValue: The value saved in this parameter depends on the ongoing procedure - * Mass Erase: Bank number which has been requested to erase - * Sectors Erase: Sector which has been erased - * (if 0xFFFFFFFFU, it means that all the selected sectors have been erased) - * Program: Address which was selected for data program - * @retval None - */ -__weak void HAL_FLASH_EndOfOperationCallback(uint32_t ReturnValue) -{ - /* Prevent unused argument(s) compilation warning */ - UNUSED(ReturnValue); - /* NOTE : This function Should not be modified, when the callback is needed, - the HAL_FLASH_EndOfOperationCallback could be implemented in the user file - */ -} - -/** - * @brief FLASH operation error interrupt callback - * @param ReturnValue: The value saved in this parameter depends on the ongoing procedure - * Mass Erase: Bank number which has been requested to erase - * Sectors Erase: Sector number which returned an error - * Program: Address which was selected for data program - * @retval None - */ -__weak void HAL_FLASH_OperationErrorCallback(uint32_t ReturnValue) -{ - /* Prevent unused argument(s) compilation warning */ - UNUSED(ReturnValue); - /* NOTE : This function Should not be modified, when the callback is needed, - the HAL_FLASH_OperationErrorCallback could be implemented in the user file - */ -} - -/** - * @} - */ - -/** @defgroup FLASH_Exported_Functions_Group2 Peripheral Control functions - * @brief management functions - * -@verbatim - =============================================================================== - ##### Peripheral Control functions ##### - =============================================================================== - [..] - This subsection provides a set of functions allowing to control the FLASH - memory operations. - -@endverbatim - * @{ - */ - -/** - * @brief Unlock the FLASH control register access - * @retval HAL Status - */ -HAL_StatusTypeDef HAL_FLASH_Unlock(void) -{ - if ((FLASH->CR & FLASH_CR_LOCK) != RESET) - { - /* Authorize the FLASH Registers access */ - FLASH->KEYR = FLASH_KEY1; - FLASH->KEYR = FLASH_KEY2; - } - else - { - return HAL_ERROR; - } - - return HAL_OK; -} - -/** - * @brief Locks the FLASH control register access - * @retval HAL Status - */ -HAL_StatusTypeDef HAL_FLASH_Lock(void) -{ - /* Set the LOCK Bit to lock the FLASH Registers access */ - FLASH->CR |= FLASH_CR_LOCK; - return HAL_OK; -} - -/** - * @brief Unlock the FLASH Option Control Registers access. - * @retval HAL Status - */ -HAL_StatusTypeDef HAL_FLASH_OB_Unlock(void) -{ - if ((FLASH->OPTCR & FLASH_OPTCR_OPTLOCK) != RESET) - { - /* Authorizes the Option Byte register programming */ - FLASH->OPTKEYR = FLASH_OPT_KEY1; - FLASH->OPTKEYR = FLASH_OPT_KEY2; - } - else - { - return HAL_ERROR; - } - - return HAL_OK; -} - -/** - * @brief Lock the FLASH Option Control Registers access. - * @retval HAL Status - */ -HAL_StatusTypeDef HAL_FLASH_OB_Lock(void) -{ - /* Set the OPTLOCK Bit to lock the FLASH Option Byte Registers access */ - FLASH->OPTCR |= FLASH_OPTCR_OPTLOCK; - return HAL_OK; -} - -/** - * @brief Launch the option byte loading. - * @retval HAL Status - */ -HAL_StatusTypeDef HAL_FLASH_OB_Launch(void) -{ - /* Set the OPTSTRT bit in OPTCR register */ - *(__IO uint8_t*)OPTCR_BYTE0_ADDRESS |= FLASH_OPTCR_OPTSTRT; - /* Wait for last operation to be completed */ - return (FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE)); -} - -/** - * @} - */ - -/** @defgroup FLASH_Exported_Functions_Group3 Peripheral State and Errors functions - * @brief Peripheral Errors functions - * -@verbatim - =============================================================================== - ##### Peripheral Errors functions ##### - =============================================================================== - [..] - This subsection permits to get in run-time Errors of the FLASH peripheral. - -@endverbatim - * @{ - */ - -/** - * @brief Get the specific FLASH error flag. - * @retval FLASH_ErrorCode: The returned value can be a combination of: - * @arg HAL_FLASH_ERROR_RD: FLASH Read Protection error flag (PCROP) - * @arg HAL_FLASH_ERROR_PGS: FLASH Programming Sequence error flag - * @arg HAL_FLASH_ERROR_PGP: FLASH Programming Parallelism error flag - * @arg HAL_FLASH_ERROR_PGA: FLASH Programming Alignment error flag - * @arg HAL_FLASH_ERROR_WRP: FLASH Write protected error flag - * @arg HAL_FLASH_ERROR_OPERATION: FLASH operation Error flag - */ -uint32_t HAL_FLASH_GetError(void) -{ - return pFlash.ErrorCode; -} - -/** - * @} - */ - -/** - * @brief Wait for a FLASH operation to complete. - * @param Timeout: maximum flash operationtimeout - * @retval HAL Status - */ -HAL_StatusTypeDef FLASH_WaitForLastOperation(uint32_t Timeout) -{ - uint32_t tickstart = 0U; - /* Clear Error Code */ - pFlash.ErrorCode = HAL_FLASH_ERROR_NONE; - /* Wait for the FLASH operation to complete by polling on BUSY flag to be reset. - Even if the FLASH operation fails, the BUSY flag will be reset and an error - flag will be set */ - /* Get tick */ - tickstart = HAL_GetTick(); - - while (__HAL_FLASH_GET_FLAG(FLASH_FLAG_BSY) != RESET) - { - if (Timeout != HAL_MAX_DELAY) - { - if ((Timeout == 0U) || ((HAL_GetTick() - tickstart ) > Timeout)) - { - return HAL_TIMEOUT; - } - } - } - - /* Check FLASH End of Operation flag */ - if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_EOP)) - { - /* Clear FLASH End of Operation pending bit */ - __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP); - } - - if (__HAL_FLASH_GET_FLAG((FLASH_FLAG_OPERR | FLASH_FLAG_WRPERR | FLASH_FLAG_PGAERR | \ - FLASH_FLAG_PGPERR | FLASH_FLAG_PGSERR | FLASH_FLAG_RDERR)) != RESET) - { - /*Save the error code*/ - FLASH_SetErrorCode(); - return HAL_ERROR; - } - - /* If there is no error flag set */ - return HAL_OK; -} - -/** - * @brief Program a double word (64-bit) at a specified address. - * @note This function must be used when the device voltage range is from - * 2.7V to 3.6V and Vpp in the range 7V to 9V. - * - * @note If an erase and a program operations are requested simultaneously, - * the erase operation is performed before the program one. - * - * @param Address: specifies the address to be programmed. - * @param Data: specifies the data to be programmed. - * @retval None - */ -static void FLASH_Program_DoubleWord(uint32_t Address, uint64_t Data) -{ - /* Check the parameters */ - assert_param(IS_FLASH_ADDRESS(Address)); - /* If the previous operation is completed, proceed to program the new data */ - CLEAR_BIT(FLASH->CR, FLASH_CR_PSIZE); - FLASH->CR |= FLASH_PSIZE_DOUBLE_WORD; - FLASH->CR |= FLASH_CR_PG; - *(__IO uint64_t*)Address = Data; -} - - -/** - * @brief Program word (32-bit) at a specified address. - * @note This function must be used when the device voltage range is from - * 2.7V to 3.6V. - * - * @note If an erase and a program operations are requested simultaneously, - * the erase operation is performed before the program one. - * - * @param Address: specifies the address to be programmed. - * @param Data: specifies the data to be programmed. - * @retval None - */ -static void FLASH_Program_Word(uint32_t Address, uint32_t Data) -{ - /* Check the parameters */ - assert_param(IS_FLASH_ADDRESS(Address)); - /* If the previous operation is completed, proceed to program the new data */ - CLEAR_BIT(FLASH->CR, FLASH_CR_PSIZE); - FLASH->CR |= FLASH_PSIZE_WORD; - FLASH->CR |= FLASH_CR_PG; - *(__IO uint32_t*)Address = Data; -} - -/** - * @brief Program a half-word (16-bit) at a specified address. - * @note This function must be used when the device voltage range is from - * 2.1V to 3.6V. - * - * @note If an erase and a program operations are requested simultaneously, - * the erase operation is performed before the program one. - * - * @param Address: specifies the address to be programmed. - * @param Data: specifies the data to be programmed. - * @retval None - */ -static void FLASH_Program_HalfWord(uint32_t Address, uint16_t Data) -{ - /* Check the parameters */ - assert_param(IS_FLASH_ADDRESS(Address)); - /* If the previous operation is completed, proceed to program the new data */ - CLEAR_BIT(FLASH->CR, FLASH_CR_PSIZE); - FLASH->CR |= FLASH_PSIZE_HALF_WORD; - FLASH->CR |= FLASH_CR_PG; - *(__IO uint16_t*)Address = Data; -} - -/** - * @brief Program byte (8-bit) at a specified address. - * @note This function must be used when the device voltage range is from - * 1.8V to 3.6V. - * - * @note If an erase and a program operations are requested simultaneously, - * the erase operation is performed before the program one. - * - * @param Address: specifies the address to be programmed. - * @param Data: specifies the data to be programmed. - * @retval None - */ -static void FLASH_Program_Byte(uint32_t Address, uint8_t Data) -{ - /* Check the parameters */ - assert_param(IS_FLASH_ADDRESS(Address)); - /* If the previous operation is completed, proceed to program the new data */ - CLEAR_BIT(FLASH->CR, FLASH_CR_PSIZE); - FLASH->CR |= FLASH_PSIZE_BYTE; - FLASH->CR |= FLASH_CR_PG; - *(__IO uint8_t*)Address = Data; -} - -/** - * @brief Set the specific FLASH error flag. - * @retval None - */ -static void FLASH_SetErrorCode(void) -{ - if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR) != RESET) - { - pFlash.ErrorCode |= HAL_FLASH_ERROR_WRP; - /* Clear FLASH write protection error pending bit */ - __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_WRPERR); - } - - if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_PGAERR) != RESET) - { - pFlash.ErrorCode |= HAL_FLASH_ERROR_PGA; - /* Clear FLASH Programming alignment error pending bit */ - __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_PGAERR); - } - - if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_PGPERR) != RESET) - { - pFlash.ErrorCode |= HAL_FLASH_ERROR_PGP; - /* Clear FLASH Programming parallelism error pending bit */ - __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_PGPERR); - } - - if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_PGSERR) != RESET) - { - pFlash.ErrorCode |= HAL_FLASH_ERROR_PGS; - /* Clear FLASH Programming sequence error pending bit */ - __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_PGSERR); - } - - if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_RDERR) != RESET) - { - pFlash.ErrorCode |= HAL_FLASH_ERROR_RD; - /* Clear FLASH Proprietary readout protection error pending bit */ - __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_RDERR); - } - - if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_OPERR) != RESET) - { - pFlash.ErrorCode |= HAL_FLASH_ERROR_OPERATION; - /* Clear FLASH Operation error pending bit */ - __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_OPERR); - } -} - -/** - * @} - */ - -#endif /* HAL_FLASH_MODULE_ENABLED */ - -/** - * @} - */ - -/** - * @} - */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ex.c b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ex.c deleted file mode 100644 index ea6d5255..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ex.c +++ /dev/null @@ -1,1298 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_flash_ex.c - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Extended FLASH HAL module driver. - * This file provides firmware functions to manage the following - * functionalities of the FLASH extension peripheral: - * + Extended programming operations functions - * - @verbatim - ============================================================================== - ##### Flash Extension features ##### - ============================================================================== - - [..] Comparing to other previous devices, the FLASH interface for STM32F427xx/437xx and - STM32F429xx/439xx devices contains the following additional features - - (+) Capacity up to 2 Mbyte with dual bank architecture supporting read-while-write - capability (RWW) - (+) Dual bank memory organization - (+) PCROP protection for all banks - - ##### How to use this driver ##### - ============================================================================== - [..] This driver provides functions to configure and program the FLASH memory - of all STM32F427xx/437xx, STM32F429xx/439xx, STM32F469xx/479xx and STM32F446xx - devices. It includes - (#) FLASH Memory Erase functions: - (++) Lock and Unlock the FLASH interface using HAL_FLASH_Unlock() and - HAL_FLASH_Lock() functions - (++) Erase function: Erase sector, erase all sectors - (++) There are two modes of erase : - (+++) Polling Mode using HAL_FLASHEx_Erase() - (+++) Interrupt Mode using HAL_FLASHEx_Erase_IT() - - (#) Option Bytes Programming functions: Use HAL_FLASHEx_OBProgram() to : - (++) Set/Reset the write protection - (++) Set the Read protection Level - (++) Set the BOR level - (++) Program the user Option Bytes - (#) Advanced Option Bytes Programming functions: Use HAL_FLASHEx_AdvOBProgram() to : - (++) Extended space (bank 2) erase function - (++) Full FLASH space (2 Mo) erase (bank 1 and bank 2) - (++) Dual Boot activation - (++) Write protection configuration for bank 2 - (++) PCROP protection configuration and control for both banks - - @endverbatim - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @defgroup FLASHEx FLASHEx - * @brief FLASH HAL Extension module driver - * @{ - */ - -#ifdef HAL_FLASH_MODULE_ENABLED - -/* Private typedef -----------------------------------------------------------*/ -/* Private define ------------------------------------------------------------*/ -/** @addtogroup FLASHEx_Private_Constants - * @{ - */ -#define FLASH_TIMEOUT_VALUE ((uint32_t)50000U)/* 50 s */ -/** - * @} - */ - -/* Private macro -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/** @addtogroup FLASHEx_Private_Variables - * @{ - */ -extern FLASH_ProcessTypeDef pFlash; -/** - * @} - */ - -/* Private function prototypes -----------------------------------------------*/ -/** @addtogroup FLASHEx_Private_Functions - * @{ - */ -/* Option bytes control */ -static void FLASH_MassErase(uint8_t VoltageRange, uint32_t Banks); -static HAL_StatusTypeDef FLASH_OB_EnableWRP(uint32_t WRPSector, uint32_t Banks); -static HAL_StatusTypeDef FLASH_OB_DisableWRP(uint32_t WRPSector, uint32_t Banks); -static HAL_StatusTypeDef FLASH_OB_RDP_LevelConfig(uint8_t Level); -static HAL_StatusTypeDef FLASH_OB_UserConfig(uint8_t Iwdg, uint8_t Stop, uint8_t Stdby); -static HAL_StatusTypeDef FLASH_OB_BOR_LevelConfig(uint8_t Level); -static uint8_t FLASH_OB_GetUser(void); -static uint16_t FLASH_OB_GetWRP(void); -static uint8_t FLASH_OB_GetRDP(void); -static uint8_t FLASH_OB_GetBOR(void); - -#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F411xE) ||\ - defined(STM32F446xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -static HAL_StatusTypeDef FLASH_OB_EnablePCROP(uint32_t Sector); -static HAL_StatusTypeDef FLASH_OB_DisablePCROP(uint32_t Sector); -#endif /* STM32F401xC || STM32F401xE || STM32F410xx || STM32F411xE || STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) -static HAL_StatusTypeDef FLASH_OB_EnablePCROP(uint32_t SectorBank1, uint32_t SectorBank2, uint32_t Banks); -static HAL_StatusTypeDef FLASH_OB_DisablePCROP(uint32_t SectorBank1, uint32_t SectorBank2, uint32_t Banks); -static HAL_StatusTypeDef FLASH_OB_BootConfig(uint8_t BootConfig); -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - -extern HAL_StatusTypeDef FLASH_WaitForLastOperation(uint32_t Timeout); -/** - * @} - */ - -/* Exported functions --------------------------------------------------------*/ -/** @defgroup FLASHEx_Exported_Functions FLASHEx Exported Functions - * @{ - */ - -/** @defgroup FLASHEx_Exported_Functions_Group1 Extended IO operation functions - * @brief Extended IO operation functions - * -@verbatim - =============================================================================== - ##### Extended programming operation functions ##### - =============================================================================== - [..] - This subsection provides a set of functions allowing to manage the Extension FLASH - programming operations. - -@endverbatim - * @{ - */ -/** - * @brief Perform a mass erase or erase the specified FLASH memory sectors - * @param[in] pEraseInit: pointer to an FLASH_EraseInitTypeDef structure that - * contains the configuration information for the erasing. - * - * @param[out] SectorError: pointer to variable that - * contains the configuration information on faulty sector in case of error - * (0xFFFFFFFFU means that all the sectors have been correctly erased) - * - * @retval HAL Status - */ -HAL_StatusTypeDef HAL_FLASHEx_Erase(FLASH_EraseInitTypeDef* pEraseInit, uint32_t* SectorError) -{ - HAL_StatusTypeDef status = HAL_ERROR; - uint32_t index = 0U; - /* Process Locked */ - __HAL_LOCK(&pFlash); - /* Check the parameters */ - assert_param(IS_FLASH_TYPEERASE(pEraseInit->TypeErase)); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - /*Initialization of SectorError variable*/ - *SectorError = 0xFFFFFFFFU; - - if (pEraseInit->TypeErase == FLASH_TYPEERASE_MASSERASE) - { - /*Mass erase to be done*/ - FLASH_MassErase((uint8_t) pEraseInit->VoltageRange, pEraseInit->Banks); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - /* if the erase operation is completed, disable the MER Bit */ - FLASH->CR &= (~FLASH_MER_BIT); - } - else - { - /* Check the parameters */ - assert_param(IS_FLASH_NBSECTORS(pEraseInit->NbSectors + pEraseInit->Sector)); - - /* Erase by sector by sector to be done*/ - for (index = pEraseInit->Sector; index < (pEraseInit->NbSectors + pEraseInit->Sector); index++) - { - FLASH_Erase_Sector(index, (uint8_t) pEraseInit->VoltageRange); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - /* If the erase operation is completed, disable the SER and SNB Bits */ - CLEAR_BIT(FLASH->CR, (FLASH_CR_SER | FLASH_CR_SNB)); - - if (status != HAL_OK) - { - /* In case of error, stop erase procedure and return the faulty sector*/ - *SectorError = index; - break; - } - } - } - - /* Flush the caches to be sure of the data consistency */ - FLASH_FlushCaches(); - } - - /* Process Unlocked */ - __HAL_UNLOCK(&pFlash); - return status; -} - -/** - * @brief Perform a mass erase or erase the specified FLASH memory sectors with interrupt enabled - * @param pEraseInit: pointer to an FLASH_EraseInitTypeDef structure that - * contains the configuration information for the erasing. - * - * @retval HAL Status - */ -HAL_StatusTypeDef HAL_FLASHEx_Erase_IT(FLASH_EraseInitTypeDef* pEraseInit) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Process Locked */ - __HAL_LOCK(&pFlash); - /* Check the parameters */ - assert_param(IS_FLASH_TYPEERASE(pEraseInit->TypeErase)); - /* Enable End of FLASH Operation interrupt */ - __HAL_FLASH_ENABLE_IT(FLASH_IT_EOP); - /* Enable Error source interrupt */ - __HAL_FLASH_ENABLE_IT(FLASH_IT_ERR); - /* Clear pending flags (if any) */ - __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP | FLASH_FLAG_OPERR | FLASH_FLAG_WRPERR | \ - FLASH_FLAG_PGAERR | FLASH_FLAG_PGPERR | FLASH_FLAG_PGSERR); - - if (pEraseInit->TypeErase == FLASH_TYPEERASE_MASSERASE) - { - /*Mass erase to be done*/ - pFlash.ProcedureOnGoing = FLASH_PROC_MASSERASE; - pFlash.Bank = pEraseInit->Banks; - FLASH_MassErase((uint8_t) pEraseInit->VoltageRange, pEraseInit->Banks); - } - else - { - /* Erase by sector to be done*/ - /* Check the parameters */ - assert_param(IS_FLASH_NBSECTORS(pEraseInit->NbSectors + pEraseInit->Sector)); - pFlash.ProcedureOnGoing = FLASH_PROC_SECTERASE; - pFlash.NbSectorsToErase = pEraseInit->NbSectors; - pFlash.Sector = pEraseInit->Sector; - pFlash.VoltageForErase = (uint8_t)pEraseInit->VoltageRange; - /*Erase 1st sector and wait for IT*/ - FLASH_Erase_Sector(pEraseInit->Sector, pEraseInit->VoltageRange); - } - - return status; -} - -/** - * @brief Program option bytes - * @param pOBInit: pointer to an FLASH_OBInitStruct structure that - * contains the configuration information for the programming. - * - * @retval HAL Status - */ -HAL_StatusTypeDef HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef* pOBInit) -{ - HAL_StatusTypeDef status = HAL_ERROR; - /* Process Locked */ - __HAL_LOCK(&pFlash); - /* Check the parameters */ - assert_param(IS_OPTIONBYTE(pOBInit->OptionType)); - - /*Write protection configuration*/ - if ((pOBInit->OptionType & OPTIONBYTE_WRP) == OPTIONBYTE_WRP) - { - assert_param(IS_WRPSTATE(pOBInit->WRPState)); - - if (pOBInit->WRPState == OB_WRPSTATE_ENABLE) - { - /*Enable of Write protection on the selected Sector*/ - status = FLASH_OB_EnableWRP(pOBInit->WRPSector, pOBInit->Banks); - } - else - { - /*Disable of Write protection on the selected Sector*/ - status = FLASH_OB_DisableWRP(pOBInit->WRPSector, pOBInit->Banks); - } - } - - /*Read protection configuration*/ - if ((pOBInit->OptionType & OPTIONBYTE_RDP) == OPTIONBYTE_RDP) - { - status = FLASH_OB_RDP_LevelConfig(pOBInit->RDPLevel); - } - - /*USER configuration*/ - if ((pOBInit->OptionType & OPTIONBYTE_USER) == OPTIONBYTE_USER) - { - status = FLASH_OB_UserConfig(pOBInit->USERConfig & OB_IWDG_SW, - pOBInit->USERConfig & OB_STOP_NO_RST, - pOBInit->USERConfig & OB_STDBY_NO_RST); - } - - /*BOR Level configuration*/ - if ((pOBInit->OptionType & OPTIONBYTE_BOR) == OPTIONBYTE_BOR) - { - status = FLASH_OB_BOR_LevelConfig(pOBInit->BORLevel); - } - - /* Process Unlocked */ - __HAL_UNLOCK(&pFlash); - return status; -} - -/** - * @brief Get the Option byte configuration - * @param pOBInit: pointer to an FLASH_OBInitStruct structure that - * contains the configuration information for the programming. - * - * @retval None - */ -void HAL_FLASHEx_OBGetConfig(FLASH_OBProgramInitTypeDef* pOBInit) -{ - pOBInit->OptionType = OPTIONBYTE_WRP | OPTIONBYTE_RDP | OPTIONBYTE_USER | OPTIONBYTE_BOR; - /*Get WRP*/ - pOBInit->WRPSector = (uint32_t)FLASH_OB_GetWRP(); - /*Get RDP Level*/ - pOBInit->RDPLevel = (uint32_t)FLASH_OB_GetRDP(); - /*Get USER*/ - pOBInit->USERConfig = (uint8_t)FLASH_OB_GetUser(); - /*Get BOR Level*/ - pOBInit->BORLevel = (uint32_t)FLASH_OB_GetBOR(); -} - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) ||\ - defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F469xx) ||\ - defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) ||\ - defined(STM32F412Cx) -/** - * @brief Program option bytes - * @param pAdvOBInit: pointer to an FLASH_AdvOBProgramInitTypeDef structure that - * contains the configuration information for the programming. - * - * @retval HAL Status - */ -HAL_StatusTypeDef HAL_FLASHEx_AdvOBProgram (FLASH_AdvOBProgramInitTypeDef* pAdvOBInit) -{ - HAL_StatusTypeDef status = HAL_ERROR; - /* Check the parameters */ - assert_param(IS_OBEX(pAdvOBInit->OptionType)); - - /*Program PCROP option byte*/ - if (((pAdvOBInit->OptionType) & OPTIONBYTE_PCROP) == OPTIONBYTE_PCROP) - { - /* Check the parameters */ - assert_param(IS_PCROPSTATE(pAdvOBInit->PCROPState)); - - if ((pAdvOBInit->PCROPState) == OB_PCROP_STATE_ENABLE) - { - /*Enable of Write protection on the selected Sector*/ -#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) ||\ - defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) ||\ - defined(STM32F412Cx) - status = FLASH_OB_EnablePCROP(pAdvOBInit->Sectors); -#else /* STM32F427xx || STM32F437xx || STM32F429xx|| STM32F439xx || STM32F469xx || STM32F479xx */ - status = FLASH_OB_EnablePCROP(pAdvOBInit->SectorsBank1, pAdvOBInit->SectorsBank2, pAdvOBInit->Banks); -#endif /* STM32F401xC || STM32F401xE || STM32F410xx || STM32F411xE || STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - } - else - { - /*Disable of Write protection on the selected Sector*/ -#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) ||\ - defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) ||\ - defined(STM32F412Cx) - status = FLASH_OB_DisablePCROP(pAdvOBInit->Sectors); -#else /* STM32F427xx || STM32F437xx || STM32F429xx|| STM32F439xx || STM32F469xx || STM32F479xx */ - status = FLASH_OB_DisablePCROP(pAdvOBInit->SectorsBank1, pAdvOBInit->SectorsBank2, pAdvOBInit->Banks); -#endif /* STM32F401xC || STM32F401xE || STM32F410xx || STM32F411xE || STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - } - } - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) - - /*Program BOOT config option byte*/ - if (((pAdvOBInit->OptionType) & OPTIONBYTE_BOOTCONFIG) == OPTIONBYTE_BOOTCONFIG) - { - status = FLASH_OB_BootConfig(pAdvOBInit->BootConfig); - } - -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - return status; -} - -/** - * @brief Get the OBEX byte configuration - * @param pAdvOBInit: pointer to an FLASH_AdvOBProgramInitTypeDef structure that - * contains the configuration information for the programming. - * - * @retval None - */ -void HAL_FLASHEx_AdvOBGetConfig(FLASH_AdvOBProgramInitTypeDef* pAdvOBInit) -{ -#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) ||\ - defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) ||\ - defined(STM32F412Cx) - /*Get Sector*/ - pAdvOBInit->Sectors = (*(__IO uint16_t*)(OPTCR_BYTE2_ADDRESS)); -#else /* STM32F427xx || STM32F437xx || STM32F429xx|| STM32F439xx || STM32F469xx || STM32F479xx */ - /*Get Sector for Bank1*/ - pAdvOBInit->SectorsBank1 = (*(__IO uint16_t*)(OPTCR_BYTE2_ADDRESS)); - /*Get Sector for Bank2*/ - pAdvOBInit->SectorsBank2 = (*(__IO uint16_t*)(OPTCR1_BYTE2_ADDRESS)); - /*Get Boot config OB*/ - pAdvOBInit->BootConfig = *(__IO uint8_t*)OPTCR_BYTE0_ADDRESS; -#endif /* STM32F401xC || STM32F401xE || STM32F410xx || STM32F411xE || STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ -} - -/** - * @brief Select the Protection Mode - * - * @note After PCROP activated Option Byte modification NOT POSSIBLE! excepted - * Global Read Out Protection modification (from level1 to level0) - * @note Once SPRMOD bit is active unprotection of a protected sector is not possible - * @note Read a protected sector will set RDERR Flag and write a protected sector will set WRPERR Flag - * @note This function can be used only for STM32F42xxx/STM32F43xxx/STM32F401xx/STM32F411xx/STM32F446xx/ - * STM32F469xx/STM32F479xx/STM32F412Zx/STM32F412Vx/STM32F412Rx/STM32F412Cx devices. - * - * @retval HAL Status - */ -HAL_StatusTypeDef HAL_FLASHEx_OB_SelectPCROP(void) -{ - uint8_t optiontmp = 0xFFU; - /* Mask SPRMOD bit */ - optiontmp = (uint8_t)((*(__IO uint8_t*)OPTCR_BYTE3_ADDRESS) & (uint8_t)0x7FU); - /* Update Option Byte */ - *(__IO uint8_t*)OPTCR_BYTE3_ADDRESS = (uint8_t)(OB_PCROP_SELECTED | optiontmp); - return HAL_OK; -} - -/** - * @brief Deselect the Protection Mode - * - * @note After PCROP activated Option Byte modification NOT POSSIBLE! excepted - * Global Read Out Protection modification (from level1 to level0) - * @note Once SPRMOD bit is active unprotection of a protected sector is not possible - * @note Read a protected sector will set RDERR Flag and write a protected sector will set WRPERR Flag - * @note This function can be used only for STM32F42xxx/STM32F43xxx/STM32F401xx/STM32F411xx/STM32F446xx/ - * STM32F469xx/STM32F479xx/STM32F412Zx/STM32F412Vx/STM32F412Rx/STM32F412Cx devices. - * - * @retval HAL Status - */ -HAL_StatusTypeDef HAL_FLASHEx_OB_DeSelectPCROP(void) -{ - uint8_t optiontmp = 0xFFU; - /* Mask SPRMOD bit */ - optiontmp = (uint8_t)((*(__IO uint8_t*)OPTCR_BYTE3_ADDRESS) & (uint8_t)0x7FU); - /* Update Option Byte */ - *(__IO uint8_t*)OPTCR_BYTE3_ADDRESS = (uint8_t)(OB_PCROP_DESELECTED | optiontmp); - return HAL_OK; -} -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F401xC || STM32F401xE || STM32F410xx ||\ - STM32F411xE || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) -/** - * @brief Returns the FLASH Write Protection Option Bytes value for Bank 2 - * @note This function can be used only for STM32F42xxx/STM32F43xxx/STM32F469xx/STM32F479xx devices. - * @retval The FLASH Write Protection Option Bytes value - */ -uint16_t HAL_FLASHEx_OB_GetBank2WRP(void) -{ - /* Return the FLASH write protection Register value */ - return (*(__IO uint16_t*)(OPTCR1_BYTE2_ADDRESS)); -} -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - -/** - * @} - */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) -/** - * @brief Full erase of FLASH memory sectors - * @param VoltageRange: The device voltage range which defines the erase parallelism. - * This parameter can be one of the following values: - * @arg FLASH_VOLTAGE_RANGE_1: when the device voltage range is 1.8V to 2.1V, - * the operation will be done by byte (8-bit) - * @arg FLASH_VOLTAGE_RANGE_2: when the device voltage range is 2.1V to 2.7V, - * the operation will be done by half word (16-bit) - * @arg FLASH_VOLTAGE_RANGE_3: when the device voltage range is 2.7V to 3.6V, - * the operation will be done by word (32-bit) - * @arg FLASH_VOLTAGE_RANGE_4: when the device voltage range is 2.7V to 3.6V + External Vpp, - * the operation will be done by double word (64-bit) - * - * @param Banks: Banks to be erased - * This parameter can be one of the following values: - * @arg FLASH_BANK_1: Bank1 to be erased - * @arg FLASH_BANK_2: Bank2 to be erased - * @arg FLASH_BANK_BOTH: Bank1 and Bank2 to be erased - * - * @retval HAL Status - */ -static void FLASH_MassErase(uint8_t VoltageRange, uint32_t Banks) -{ - /* Check the parameters */ - assert_param(IS_VOLTAGERANGE(VoltageRange)); - assert_param(IS_FLASH_BANK(Banks)); - /* if the previous operation is completed, proceed to erase all sectors */ - CLEAR_BIT(FLASH->CR, FLASH_CR_PSIZE); - - if (Banks == FLASH_BANK_BOTH) - { - /* bank1 & bank2 will be erased*/ - FLASH->CR |= FLASH_MER_BIT; - } - else if (Banks == FLASH_BANK_1) - { - /*Only bank1 will be erased*/ - FLASH->CR |= FLASH_CR_MER1; - } - else - { - /*Only bank2 will be erased*/ - FLASH->CR |= FLASH_CR_MER2; - } - - FLASH->CR |= FLASH_CR_STRT | ((uint32_t)VoltageRange << 8U); -} - -/** - * @brief Erase the specified FLASH memory sector - * @param Sector: FLASH sector to erase - * The value of this parameter depend on device used within the same series - * @param VoltageRange: The device voltage range which defines the erase parallelism. - * This parameter can be one of the following values: - * @arg FLASH_VOLTAGE_RANGE_1: when the device voltage range is 1.8V to 2.1V, - * the operation will be done by byte (8-bit) - * @arg FLASH_VOLTAGE_RANGE_2: when the device voltage range is 2.1V to 2.7V, - * the operation will be done by half word (16-bit) - * @arg FLASH_VOLTAGE_RANGE_3: when the device voltage range is 2.7V to 3.6V, - * the operation will be done by word (32-bit) - * @arg FLASH_VOLTAGE_RANGE_4: when the device voltage range is 2.7V to 3.6V + External Vpp, - * the operation will be done by double word (64-bit) - * - * @retval None - */ -void FLASH_Erase_Sector(uint32_t Sector, uint8_t VoltageRange) -{ - uint32_t tmp_psize = 0U; - /* Check the parameters */ - assert_param(IS_FLASH_SECTOR(Sector)); - assert_param(IS_VOLTAGERANGE(VoltageRange)); - - if (VoltageRange == FLASH_VOLTAGE_RANGE_1) - { - tmp_psize = FLASH_PSIZE_BYTE; - } - else if (VoltageRange == FLASH_VOLTAGE_RANGE_2) - { - tmp_psize = FLASH_PSIZE_HALF_WORD; - } - else if (VoltageRange == FLASH_VOLTAGE_RANGE_3) - { - tmp_psize = FLASH_PSIZE_WORD; - } - else - { - tmp_psize = FLASH_PSIZE_DOUBLE_WORD; - } - - /* Need to add offset of 4 when sector higher than FLASH_SECTOR_11 */ - if (Sector > FLASH_SECTOR_11) - { - Sector += 4U; - } - - /* If the previous operation is completed, proceed to erase the sector */ - CLEAR_BIT(FLASH->CR, FLASH_CR_PSIZE); - FLASH->CR |= tmp_psize; - CLEAR_BIT(FLASH->CR, FLASH_CR_SNB); - FLASH->CR |= FLASH_CR_SER | (Sector << POSITION_VAL(FLASH_CR_SNB)); - FLASH->CR |= FLASH_CR_STRT; -} - -/** - * @brief Enable the write protection of the desired bank1 or bank 2 sectors - * - * @note When the memory read protection level is selected (RDP level = 1), - * it is not possible to program or erase the flash sector i if CortexM4 - * debug features are connected or boot code is executed in RAM, even if nWRPi = 1 - * @note Active value of nWRPi bits is inverted when PCROP mode is active (SPRMOD =1). - * - * @param WRPSector: specifies the sector(s) to be write protected. - * This parameter can be one of the following values: - * @arg WRPSector: A value between OB_WRP_SECTOR_0 and OB_WRP_SECTOR_23 - * @arg OB_WRP_SECTOR_All - * @note BANK2 starts from OB_WRP_SECTOR_12 - * - * @param Banks: Enable write protection on all the sectors for the specific bank - * This parameter can be one of the following values: - * @arg FLASH_BANK_1: WRP on all sectors of bank1 - * @arg FLASH_BANK_2: WRP on all sectors of bank2 - * @arg FLASH_BANK_BOTH: WRP on all sectors of bank1 & bank2 - * - * @retval HAL FLASH State - */ -static HAL_StatusTypeDef FLASH_OB_EnableWRP(uint32_t WRPSector, uint32_t Banks) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Check the parameters */ - assert_param(IS_OB_WRP_SECTOR(WRPSector)); - assert_param(IS_FLASH_BANK(Banks)); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - if (((WRPSector == OB_WRP_SECTOR_All) && ((Banks == FLASH_BANK_1) || (Banks == FLASH_BANK_BOTH))) || - (WRPSector < OB_WRP_SECTOR_12)) - { - if (WRPSector == OB_WRP_SECTOR_All) - { - /*Write protection on all sector of BANK1*/ - *(__IO uint16_t*)OPTCR_BYTE2_ADDRESS &= (~(WRPSector >> 12U)); - } - else - { - /*Write protection done on sectors of BANK1*/ - *(__IO uint16_t*)OPTCR_BYTE2_ADDRESS &= (~WRPSector); - } - } - else - { - /*Write protection done on sectors of BANK2*/ - *(__IO uint16_t*)OPTCR1_BYTE2_ADDRESS &= (~(WRPSector >> 12U)); - } - - /*Write protection on all sector of BANK2*/ - if ((WRPSector == OB_WRP_SECTOR_All) && (Banks == FLASH_BANK_BOTH)) - { - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - *(__IO uint16_t*)OPTCR1_BYTE2_ADDRESS &= (~(WRPSector >> 12U)); - } - } - } - - return status; -} - -/** - * @brief Disable the write protection of the desired bank1 or bank 2 sectors - * - * @note When the memory read protection level is selected (RDP level = 1), - * it is not possible to program or erase the flash sector i if CortexM4 - * debug features are connected or boot code is executed in RAM, even if nWRPi = 1 - * @note Active value of nWRPi bits is inverted when PCROP mode is active (SPRMOD =1). - * - * @param WRPSector: specifies the sector(s) to be write protected. - * This parameter can be one of the following values: - * @arg WRPSector: A value between OB_WRP_SECTOR_0 and OB_WRP_SECTOR_23 - * @arg OB_WRP_Sector_All - * @note BANK2 starts from OB_WRP_SECTOR_12 - * - * @param Banks: Disable write protection on all the sectors for the specific bank - * This parameter can be one of the following values: - * @arg FLASH_BANK_1: Bank1 to be erased - * @arg FLASH_BANK_2: Bank2 to be erased - * @arg FLASH_BANK_BOTH: Bank1 and Bank2 to be erased - * - * @retval HAL Status - */ -static HAL_StatusTypeDef FLASH_OB_DisableWRP(uint32_t WRPSector, uint32_t Banks) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Check the parameters */ - assert_param(IS_OB_WRP_SECTOR(WRPSector)); - assert_param(IS_FLASH_BANK(Banks)); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - if (((WRPSector == OB_WRP_SECTOR_All) && ((Banks == FLASH_BANK_1) || (Banks == FLASH_BANK_BOTH))) || - (WRPSector < OB_WRP_SECTOR_12)) - { - if (WRPSector == OB_WRP_SECTOR_All) - { - /*Write protection on all sector of BANK1*/ - *(__IO uint16_t*)OPTCR_BYTE2_ADDRESS |= (uint16_t)(WRPSector >> 12U); - } - else - { - /*Write protection done on sectors of BANK1*/ - *(__IO uint16_t*)OPTCR_BYTE2_ADDRESS |= (uint16_t)WRPSector; - } - } - else - { - /*Write protection done on sectors of BANK2*/ - *(__IO uint16_t*)OPTCR1_BYTE2_ADDRESS |= (uint16_t)(WRPSector >> 12U); - } - - /*Write protection on all sector of BANK2*/ - if ((WRPSector == OB_WRP_SECTOR_All) && (Banks == FLASH_BANK_BOTH)) - { - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - *(__IO uint16_t*)OPTCR1_BYTE2_ADDRESS |= (uint16_t)(WRPSector >> 12U); - } - } - } - - return status; -} - -/** - * @brief Configure the Dual Bank Boot. - * - * @note This function can be used only for STM32F42xxx/43xxx devices. - * - * @param BootConfig specifies the Dual Bank Boot Option byte. - * This parameter can be one of the following values: - * @arg OB_Dual_BootEnabled: Dual Bank Boot Enable - * @arg OB_Dual_BootDisabled: Dual Bank Boot Disabled - * @retval None - */ -static HAL_StatusTypeDef FLASH_OB_BootConfig(uint8_t BootConfig) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Check the parameters */ - assert_param(IS_OB_BOOT(BootConfig)); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - /* Set Dual Bank Boot */ - *(__IO uint8_t*)OPTCR_BYTE0_ADDRESS &= (~FLASH_OPTCR_BFB2); - *(__IO uint8_t*)OPTCR_BYTE0_ADDRESS |= BootConfig; - } - - return status; -} - -/** - * @brief Enable the read/write protection (PCROP) of the desired - * sectors of Bank 1 and/or Bank 2. - * @note This function can be used only for STM32F42xxx/43xxx devices. - * @param SectorBank1 Specifies the sector(s) to be read/write protected or unprotected for bank1. - * This parameter can be one of the following values: - * @arg OB_PCROP: A value between OB_PCROP_SECTOR_0 and OB_PCROP_SECTOR_11 - * @arg OB_PCROP_SECTOR__All - * @param SectorBank2 Specifies the sector(s) to be read/write protected or unprotected for bank2. - * This parameter can be one of the following values: - * @arg OB_PCROP: A value between OB_PCROP_SECTOR_12 and OB_PCROP_SECTOR_23 - * @arg OB_PCROP_SECTOR__All - * @param Banks Enable PCROP protection on all the sectors for the specific bank - * This parameter can be one of the following values: - * @arg FLASH_BANK_1: WRP on all sectors of bank1 - * @arg FLASH_BANK_2: WRP on all sectors of bank2 - * @arg FLASH_BANK_BOTH: WRP on all sectors of bank1 & bank2 - * - * @retval HAL Status - */ -static HAL_StatusTypeDef FLASH_OB_EnablePCROP(uint32_t SectorBank1, uint32_t SectorBank2, uint32_t Banks) -{ - HAL_StatusTypeDef status = HAL_OK; - assert_param(IS_FLASH_BANK(Banks)); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - if ((Banks == FLASH_BANK_1) || (Banks == FLASH_BANK_BOTH)) - { - assert_param(IS_OB_PCROP(SectorBank1)); - /*Write protection done on sectors of BANK1*/ - *(__IO uint16_t*)OPTCR_BYTE2_ADDRESS |= (uint16_t)SectorBank1; - } - else - { - assert_param(IS_OB_PCROP(SectorBank2)); - /*Write protection done on sectors of BANK2*/ - *(__IO uint16_t*)OPTCR1_BYTE2_ADDRESS |= (uint16_t)SectorBank2; - } - - /*Write protection on all sector of BANK2*/ - if (Banks == FLASH_BANK_BOTH) - { - assert_param(IS_OB_PCROP(SectorBank2)); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - /*Write protection done on sectors of BANK2*/ - *(__IO uint16_t*)OPTCR1_BYTE2_ADDRESS |= (uint16_t)SectorBank2; - } - } - } - - return status; -} - - -/** - * @brief Disable the read/write protection (PCROP) of the desired - * sectors of Bank 1 and/or Bank 2. - * @note This function can be used only for STM32F42xxx/43xxx devices. - * @param SectorBank1 specifies the sector(s) to be read/write protected or unprotected for bank1. - * This parameter can be one of the following values: - * @arg OB_PCROP: A value between OB_PCROP_SECTOR_0 and OB_PCROP_SECTOR_11 - * @arg OB_PCROP_SECTOR__All - * @param SectorBank2 Specifies the sector(s) to be read/write protected or unprotected for bank2. - * This parameter can be one of the following values: - * @arg OB_PCROP: A value between OB_PCROP_SECTOR_12 and OB_PCROP_SECTOR_23 - * @arg OB_PCROP_SECTOR__All - * @param Banks Disable PCROP protection on all the sectors for the specific bank - * This parameter can be one of the following values: - * @arg FLASH_BANK_1: WRP on all sectors of bank1 - * @arg FLASH_BANK_2: WRP on all sectors of bank2 - * @arg FLASH_BANK_BOTH: WRP on all sectors of bank1 & bank2 - * - * @retval HAL Status - */ -static HAL_StatusTypeDef FLASH_OB_DisablePCROP(uint32_t SectorBank1, uint32_t SectorBank2, uint32_t Banks) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Check the parameters */ - assert_param(IS_FLASH_BANK(Banks)); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - if ((Banks == FLASH_BANK_1) || (Banks == FLASH_BANK_BOTH)) - { - assert_param(IS_OB_PCROP(SectorBank1)); - /*Write protection done on sectors of BANK1*/ - *(__IO uint16_t*)OPTCR_BYTE2_ADDRESS &= (~SectorBank1); - } - else - { - /*Write protection done on sectors of BANK2*/ - assert_param(IS_OB_PCROP(SectorBank2)); - *(__IO uint16_t*)OPTCR1_BYTE2_ADDRESS &= (~SectorBank2); - } - - /*Write protection on all sector of BANK2*/ - if (Banks == FLASH_BANK_BOTH) - { - assert_param(IS_OB_PCROP(SectorBank2)); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - /*Write protection done on sectors of BANK2*/ - *(__IO uint16_t*)OPTCR1_BYTE2_ADDRESS &= (~SectorBank2); - } - } - } - - return status; -} - -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ - -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) ||\ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) ||\ - defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F412Zx) ||\ - defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -/** - * @brief Mass erase of FLASH memory - * @param VoltageRange: The device voltage range which defines the erase parallelism. - * This parameter can be one of the following values: - * @arg FLASH_VOLTAGE_RANGE_1: when the device voltage range is 1.8V to 2.1V, - * the operation will be done by byte (8-bit) - * @arg FLASH_VOLTAGE_RANGE_2: when the device voltage range is 2.1V to 2.7V, - * the operation will be done by half word (16-bit) - * @arg FLASH_VOLTAGE_RANGE_3: when the device voltage range is 2.7V to 3.6V, - * the operation will be done by word (32-bit) - * @arg FLASH_VOLTAGE_RANGE_4: when the device voltage range is 2.7V to 3.6V + External Vpp, - * the operation will be done by double word (64-bit) - * - * @param Banks: Banks to be erased - * This parameter can be one of the following values: - * @arg FLASH_BANK_1: Bank1 to be erased - * - * @retval None - */ -static void FLASH_MassErase(uint8_t VoltageRange, uint32_t Banks) -{ - /* Check the parameters */ - assert_param(IS_VOLTAGERANGE(VoltageRange)); - assert_param(IS_FLASH_BANK(Banks)); - /* If the previous operation is completed, proceed to erase all sectors */ - CLEAR_BIT(FLASH->CR, FLASH_CR_PSIZE); - FLASH->CR |= FLASH_CR_MER; - FLASH->CR |= FLASH_CR_STRT | ((uint32_t)VoltageRange << 8U); -} - -/** - * @brief Erase the specified FLASH memory sector - * @param Sector: FLASH sector to erase - * The value of this parameter depend on device used within the same series - * @param VoltageRange: The device voltage range which defines the erase parallelism. - * This parameter can be one of the following values: - * @arg FLASH_VOLTAGE_RANGE_1: when the device voltage range is 1.8V to 2.1V, - * the operation will be done by byte (8-bit) - * @arg FLASH_VOLTAGE_RANGE_2: when the device voltage range is 2.1V to 2.7V, - * the operation will be done by half word (16-bit) - * @arg FLASH_VOLTAGE_RANGE_3: when the device voltage range is 2.7V to 3.6V, - * the operation will be done by word (32-bit) - * @arg FLASH_VOLTAGE_RANGE_4: when the device voltage range is 2.7V to 3.6V + External Vpp, - * the operation will be done by double word (64-bit) - * - * @retval None - */ -void FLASH_Erase_Sector(uint32_t Sector, uint8_t VoltageRange) -{ - uint32_t tmp_psize = 0U; - /* Check the parameters */ - assert_param(IS_FLASH_SECTOR(Sector)); - assert_param(IS_VOLTAGERANGE(VoltageRange)); - - if (VoltageRange == FLASH_VOLTAGE_RANGE_1) - { - tmp_psize = FLASH_PSIZE_BYTE; - } - else if (VoltageRange == FLASH_VOLTAGE_RANGE_2) - { - tmp_psize = FLASH_PSIZE_HALF_WORD; - } - else if (VoltageRange == FLASH_VOLTAGE_RANGE_3) - { - tmp_psize = FLASH_PSIZE_WORD; - } - else - { - tmp_psize = FLASH_PSIZE_DOUBLE_WORD; - } - - /* If the previous operation is completed, proceed to erase the sector */ - CLEAR_BIT(FLASH->CR, FLASH_CR_PSIZE); - FLASH->CR |= tmp_psize; - CLEAR_BIT(FLASH->CR, FLASH_CR_SNB); - FLASH->CR |= FLASH_CR_SER | (Sector << POSITION_VAL(FLASH_CR_SNB)); - FLASH->CR |= FLASH_CR_STRT; -} - -/** - * @brief Enable the write protection of the desired bank 1 sectors - * - * @note When the memory read protection level is selected (RDP level = 1), - * it is not possible to program or erase the flash sector i if CortexM4 - * debug features are connected or boot code is executed in RAM, even if nWRPi = 1 - * @note Active value of nWRPi bits is inverted when PCROP mode is active (SPRMOD =1). - * - * @param WRPSector: specifies the sector(s) to be write protected. - * The value of this parameter depend on device used within the same series - * - * @param Banks: Enable write protection on all the sectors for the specific bank - * This parameter can be one of the following values: - * @arg FLASH_BANK_1: WRP on all sectors of bank1 - * - * @retval HAL Status - */ -static HAL_StatusTypeDef FLASH_OB_EnableWRP(uint32_t WRPSector, uint32_t Banks) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Check the parameters */ - assert_param(IS_OB_WRP_SECTOR(WRPSector)); - assert_param(IS_FLASH_BANK(Banks)); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - *(__IO uint16_t*)OPTCR_BYTE2_ADDRESS &= (~WRPSector); - } - - return status; -} - -/** - * @brief Disable the write protection of the desired bank 1 sectors - * - * @note When the memory read protection level is selected (RDP level = 1), - * it is not possible to program or erase the flash sector i if CortexM4 - * debug features are connected or boot code is executed in RAM, even if nWRPi = 1 - * @note Active value of nWRPi bits is inverted when PCROP mode is active (SPRMOD =1). - * - * @param WRPSector: specifies the sector(s) to be write protected. - * The value of this parameter depend on device used within the same series - * - * @param Banks: Enable write protection on all the sectors for the specific bank - * This parameter can be one of the following values: - * @arg FLASH_BANK_1: WRP on all sectors of bank1 - * - * @retval HAL Status - */ -static HAL_StatusTypeDef FLASH_OB_DisableWRP(uint32_t WRPSector, uint32_t Banks) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Check the parameters */ - assert_param(IS_OB_WRP_SECTOR(WRPSector)); - assert_param(IS_FLASH_BANK(Banks)); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - *(__IO uint16_t*)OPTCR_BYTE2_ADDRESS |= (uint16_t)WRPSector; - } - - return status; -} -#endif /* STM32F40xxx || STM32F41xxx || STM32F401xx || STM32F410xx || STM32F411xE || STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) ||\ - defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) ||\ - defined(STM32F412Cx) -/** - * @brief Enable the read/write protection (PCROP) of the desired sectors. - * @note This function can be used only for STM32F401xx devices. - * @param Sector specifies the sector(s) to be read/write protected or unprotected. - * This parameter can be one of the following values: - * @arg OB_PCROP: A value between OB_PCROP_Sector0 and OB_PCROP_Sector5 - * @arg OB_PCROP_Sector_All - * @retval HAL Status - */ -static HAL_StatusTypeDef FLASH_OB_EnablePCROP(uint32_t Sector) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Check the parameters */ - assert_param(IS_OB_PCROP(Sector)); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - *(__IO uint16_t*)OPTCR_BYTE2_ADDRESS |= (uint16_t)Sector; - } - - return status; -} - - -/** - * @brief Disable the read/write protection (PCROP) of the desired sectors. - * @note This function can be used only for STM32F401xx devices. - * @param Sector specifies the sector(s) to be read/write protected or unprotected. - * This parameter can be one of the following values: - * @arg OB_PCROP: A value between OB_PCROP_Sector0 and OB_PCROP_Sector5 - * @arg OB_PCROP_Sector_All - * @retval HAL Status - */ -static HAL_StatusTypeDef FLASH_OB_DisablePCROP(uint32_t Sector) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Check the parameters */ - assert_param(IS_OB_PCROP(Sector)); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - *(__IO uint16_t*)OPTCR_BYTE2_ADDRESS &= (~Sector); - } - - return status; -} -#endif /* STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -/** - * @brief Set the read protection level. - * @param Level: specifies the read protection level. - * This parameter can be one of the following values: - * @arg OB_RDP_LEVEL_0: No protection - * @arg OB_RDP_LEVEL_1: Read protection of the memory - * @arg OB_RDP_LEVEL_2: Full chip protection - * - * @note WARNING: When enabling OB_RDP level 2 it's no more possible to go back to level 1 or 0 - * - * @retval HAL Status - */ -static HAL_StatusTypeDef FLASH_OB_RDP_LevelConfig(uint8_t Level) -{ - HAL_StatusTypeDef status = HAL_OK; - /* Check the parameters */ - assert_param(IS_OB_RDP_LEVEL(Level)); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - *(__IO uint8_t*)OPTCR_BYTE1_ADDRESS = Level; - } - - return status; -} - -/** - * @brief Program the FLASH User Option Byte: IWDG_SW / RST_STOP / RST_STDBY. - * @param Iwdg: Selects the IWDG mode - * This parameter can be one of the following values: - * @arg OB_IWDG_SW: Software IWDG selected - * @arg OB_IWDG_HW: Hardware IWDG selected - * @param Stop: Reset event when entering STOP mode. - * This parameter can be one of the following values: - * @arg OB_STOP_NO_RST: No reset generated when entering in STOP - * @arg OB_STOP_RST: Reset generated when entering in STOP - * @param Stdby: Reset event when entering Standby mode. - * This parameter can be one of the following values: - * @arg OB_STDBY_NO_RST: No reset generated when entering in STANDBY - * @arg OB_STDBY_RST: Reset generated when entering in STANDBY - * @retval HAL Status - */ -static HAL_StatusTypeDef FLASH_OB_UserConfig(uint8_t Iwdg, uint8_t Stop, uint8_t Stdby) -{ - uint8_t optiontmp = 0xFFU; - HAL_StatusTypeDef status = HAL_OK; - /* Check the parameters */ - assert_param(IS_OB_IWDG_SOURCE(Iwdg)); - assert_param(IS_OB_STOP_SOURCE(Stop)); - assert_param(IS_OB_STDBY_SOURCE(Stdby)); - /* Wait for last operation to be completed */ - status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE); - - if (status == HAL_OK) - { - /* Mask OPTLOCK, OPTSTRT, BOR_LEV and BFB2 bits */ - optiontmp = (uint8_t)((*(__IO uint8_t*)OPTCR_BYTE0_ADDRESS) & (uint8_t)0x1FU); - /* Update User Option Byte */ - *(__IO uint8_t*)OPTCR_BYTE0_ADDRESS = Iwdg | (uint8_t)(Stdby | (uint8_t)(Stop | ((uint8_t)optiontmp))); - } - - return status; -} - -/** - * @brief Set the BOR Level. - * @param Level: specifies the Option Bytes BOR Reset Level. - * This parameter can be one of the following values: - * @arg OB_BOR_LEVEL3: Supply voltage ranges from 2.7 to 3.6 V - * @arg OB_BOR_LEVEL2: Supply voltage ranges from 2.4 to 2.7 V - * @arg OB_BOR_LEVEL1: Supply voltage ranges from 2.1 to 2.4 V - * @arg OB_BOR_OFF: Supply voltage ranges from 1.62 to 2.1 V - * @retval HAL Status - */ -static HAL_StatusTypeDef FLASH_OB_BOR_LevelConfig(uint8_t Level) -{ - /* Check the parameters */ - assert_param(IS_OB_BOR_LEVEL(Level)); - /* Set the BOR Level */ - *(__IO uint8_t*)OPTCR_BYTE0_ADDRESS &= (~FLASH_OPTCR_BOR_LEV); - *(__IO uint8_t*)OPTCR_BYTE0_ADDRESS |= Level; - return HAL_OK; -} - -/** - * @brief Return the FLASH User Option Byte value. - * @retval uint8_t FLASH User Option Bytes values: IWDG_SW(Bit0), RST_STOP(Bit1) - * and RST_STDBY(Bit2). - */ -static uint8_t FLASH_OB_GetUser(void) -{ - /* Return the User Option Byte */ - return ((uint8_t)(FLASH->OPTCR & 0xE0U)); -} - -/** - * @brief Return the FLASH Write Protection Option Bytes value. - * @retval uint16_t FLASH Write Protection Option Bytes value - */ -static uint16_t FLASH_OB_GetWRP(void) -{ - /* Return the FLASH write protection Register value */ - return (*(__IO uint16_t*)(OPTCR_BYTE2_ADDRESS)); -} - -/** - * @brief Returns the FLASH Read Protection level. - * @retval FLASH ReadOut Protection Status: - * This parameter can be one of the following values: - * @arg OB_RDP_LEVEL_0: No protection - * @arg OB_RDP_LEVEL_1: Read protection of the memory - * @arg OB_RDP_LEVEL_2: Full chip protection - */ -static uint8_t FLASH_OB_GetRDP(void) -{ - uint8_t readstatus = OB_RDP_LEVEL_0; - - if ((*(__IO uint8_t*)(OPTCR_BYTE1_ADDRESS) == (uint8_t)OB_RDP_LEVEL_2)) - { - readstatus = OB_RDP_LEVEL_2; - } - else if ((*(__IO uint8_t*)(OPTCR_BYTE1_ADDRESS) == (uint8_t)OB_RDP_LEVEL_1)) - { - readstatus = OB_RDP_LEVEL_1; - } - else - { - readstatus = OB_RDP_LEVEL_0; - } - - return readstatus; -} - -/** - * @brief Returns the FLASH BOR level. - * @retval uint8_t The FLASH BOR level: - * - OB_BOR_LEVEL3: Supply voltage ranges from 2.7 to 3.6 V - * - OB_BOR_LEVEL2: Supply voltage ranges from 2.4 to 2.7 V - * - OB_BOR_LEVEL1: Supply voltage ranges from 2.1 to 2.4 V - * - OB_BOR_OFF : Supply voltage ranges from 1.62 to 2.1 V - */ -static uint8_t FLASH_OB_GetBOR(void) -{ - /* Return the FLASH BOR level */ - return (uint8_t)(*(__IO uint8_t*)(OPTCR_BYTE0_ADDRESS) & (uint8_t)0x0CU); -} - -/** - * @brief Flush the instruction and data caches - * @retval None - */ -void FLASH_FlushCaches(void) -{ - /* Flush instruction cache */ - if (READ_BIT(FLASH->ACR, FLASH_ACR_ICEN) != RESET) - { - /* Disable instruction cache */ - __HAL_FLASH_INSTRUCTION_CACHE_DISABLE(); - /* Reset instruction cache */ - __HAL_FLASH_INSTRUCTION_CACHE_RESET(); - /* Enable instruction cache */ - __HAL_FLASH_INSTRUCTION_CACHE_ENABLE(); - } - - /* Flush data cache */ - if (READ_BIT(FLASH->ACR, FLASH_ACR_DCEN) != RESET) - { - /* Disable data cache */ - __HAL_FLASH_DATA_CACHE_DISABLE(); - /* Reset data cache */ - __HAL_FLASH_DATA_CACHE_RESET(); - /* Enable data cache */ - __HAL_FLASH_DATA_CACHE_ENABLE(); - } -} - -/** - * @} - */ - -#endif /* HAL_FLASH_MODULE_ENABLED */ - -/** - * @} - */ - -/** - * @} - */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ramfunc.c b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ramfunc.c deleted file mode 100644 index 33bfd540..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ramfunc.c +++ /dev/null @@ -1,189 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_flash_ramfunc.c - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief FLASH RAMFUNC module driver. - * This file provides a FLASH firmware functions which should be - * executed from internal SRAM - * + Stop/Start the flash interface while System Run - * + Enable/Disable the flash sleep while System Run - @verbatim - ============================================================================== - ##### APIs executed from Internal RAM ##### - ============================================================================== - [..] - *** ARM Compiler *** - -------------------- - [..] RAM functions are defined using the toolchain options. - Functions that are be executed in RAM should reside in a separate - source module. Using the 'Options for File' dialog you can simply change - the 'Code / Const' area of a module to a memory space in physical RAM. - Available memory areas are declared in the 'Target' tab of the - Options for Target' dialog. - - *** ICCARM Compiler *** - ----------------------- - [..] RAM functions are defined using a specific toolchain keyword "__ramfunc". - - *** GNU Compiler *** - -------------------- - [..] RAM functions are defined using a specific toolchain attribute - "__attribute__((section(".RamFunc")))". - - @endverbatim - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @defgroup FLASH_RAMFUNC FLASH RAMFUNC - * @brief FLASH functions executed from RAM - * @{ - */ -#ifdef HAL_FLASH_MODULE_ENABLED -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ - defined(STM32F412Rx) || defined(STM32F412Cx) - -/* Private typedef -----------------------------------------------------------*/ -/* Private define ------------------------------------------------------------*/ -/* Private macro -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/* Private function prototypes -----------------------------------------------*/ -/* Exported functions --------------------------------------------------------*/ -/** @defgroup FLASH_RAMFUNC_Exported_Functions FLASH RAMFUNC Exported Functions - * @{ - */ - -/** @defgroup FLASH_RAMFUNC_Exported_Functions_Group1 Peripheral features functions executed from internal RAM - * @brief Peripheral Extended features functions - * -@verbatim - - =============================================================================== - ##### ramfunc functions ##### - =============================================================================== - [..] - This subsection provides a set of functions that should be executed from RAM - transfers. - -@endverbatim - * @{ - */ - -/** - * @brief Stop the flash interface while System Run - * @note This mode is only available for STM32F41xxx/STM32F446xx devices. - * @note This mode couldn't be set while executing with the flash itself. - * It should be done with specific routine executed from RAM. - * @retval None - */ -__RAM_FUNC HAL_FLASHEx_StopFlashInterfaceClk(void) -{ - /* Enable Power ctrl clock */ - __HAL_RCC_PWR_CLK_ENABLE(); - /* Stop the flash interface while System Run */ - SET_BIT(PWR->CR, PWR_CR_FISSR); - return HAL_OK; -} - -/** - * @brief Start the flash interface while System Run - * @note This mode is only available for STM32F411xx/STM32F446xx devices. - * @note This mode couldn't be set while executing with the flash itself. - * It should be done with specific routine executed from RAM. - * @retval None - */ -__RAM_FUNC HAL_FLASHEx_StartFlashInterfaceClk(void) -{ - /* Enable Power ctrl clock */ - __HAL_RCC_PWR_CLK_ENABLE(); - /* Start the flash interface while System Run */ - CLEAR_BIT(PWR->CR, PWR_CR_FISSR); - return HAL_OK; -} - -/** - * @brief Enable the flash sleep while System Run - * @note This mode is only available for STM32F41xxx/STM32F446xx devices. - * @note This mode could n't be set while executing with the flash itself. - * It should be done with specific routine executed from RAM. - * @retval None - */ -__RAM_FUNC HAL_FLASHEx_EnableFlashSleepMode(void) -{ - /* Enable Power ctrl clock */ - __HAL_RCC_PWR_CLK_ENABLE(); - /* Enable the flash sleep while System Run */ - SET_BIT(PWR->CR, PWR_CR_FMSSR); - return HAL_OK; -} - -/** - * @brief Disable the flash sleep while System Run - * @note This mode is only available for STM32F41xxx/STM32F446xx devices. - * @note This mode couldn't be set while executing with the flash itself. - * It should be done with specific routine executed from RAM. - * @retval None - */ -__RAM_FUNC HAL_FLASHEx_DisableFlashSleepMode(void) -{ - /* Enable Power ctrl clock */ - __HAL_RCC_PWR_CLK_ENABLE(); - /* Disable the flash sleep while System Run */ - CLEAR_BIT(PWR->CR, PWR_CR_FMSSR); - return HAL_OK; -} - -/** - * @} - */ - -/** - * @} - */ - -#endif /* STM32F410xx || STM32F411xE || STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ -#endif /* HAL_FLASH_MODULE_ENABLED */ -/** - * @} - */ - -/** - * @} - */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_gpio.c b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_gpio.c deleted file mode 100644 index 5a46b8b6..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_gpio.c +++ /dev/null @@ -1,538 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_gpio.c - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief GPIO HAL module driver. - * This file provides firmware functions to manage the following - * functionalities of the General Purpose Input/Output (GPIO) peripheral: - * + Initialization and de-initialization functions - * + IO operation functions - * - @verbatim - ============================================================================== - ##### GPIO Peripheral features ##### - ============================================================================== - [..] - Subject to the specific hardware characteristics of each I/O port listed in the datasheet, each - port bit of the General Purpose IO (GPIO) Ports, can be individually configured by software - in several modes: - (+) Input mode - (+) Analog mode - (+) Output mode - (+) Alternate function mode - (+) External interrupt/event lines - - [..] - During and just after reset, the alternate functions and external interrupt - lines are not active and the I/O ports are configured in input floating mode. - - [..] - All GPIO pins have weak internal pull-up and pull-down resistors, which can be - activated or not. - - [..] - In Output or Alternate mode, each IO can be configured on open-drain or push-pull - type and the IO speed can be selected depending on the VDD value. - - [..] - All ports have external interrupt/event capability. To use external interrupt - lines, the port must be configured in input mode. All available GPIO pins are - connected to the 16 external interrupt/event lines from EXTI0 to EXTI15. - - [..] - The external interrupt/event controller consists of up to 23 edge detectors - (16 lines are connected to GPIO) for generating event/interrupt requests (each - input line can be independently configured to select the type (interrupt or event) - and the corresponding trigger event (rising or falling or both). Each line can - also be masked independently. - - ##### How to use this driver ##### - ============================================================================== - [..] - (#) Enable the GPIO AHB clock using the following function: __HAL_RCC_GPIOx_CLK_ENABLE(). - - (#) Configure the GPIO pin(s) using HAL_GPIO_Init(). - (++) Configure the IO mode using "Mode" member from GPIO_InitTypeDef structure - (++) Activate Pull-up, Pull-down resistor using "Pull" member from GPIO_InitTypeDef - structure. - (++) In case of Output or alternate function mode selection: the speed is - configured through "Speed" member from GPIO_InitTypeDef structure. - (++) In alternate mode is selection, the alternate function connected to the IO - is configured through "Alternate" member from GPIO_InitTypeDef structure. - (++) Analog mode is required when a pin is to be used as ADC channel - or DAC output. - (++) In case of external interrupt/event selection the "Mode" member from - GPIO_InitTypeDef structure select the type (interrupt or event) and - the corresponding trigger event (rising or falling or both). - - (#) In case of external interrupt/event mode selection, configure NVIC IRQ priority - mapped to the EXTI line using HAL_NVIC_SetPriority() and enable it using - HAL_NVIC_EnableIRQ(). - - (#) To get the level of a pin configured in input mode use HAL_GPIO_ReadPin(). - - (#) To set/reset the level of a pin configured in output mode use - HAL_GPIO_WritePin()/HAL_GPIO_TogglePin(). - - (#) To lock pin configuration until next reset use HAL_GPIO_LockPin(). - - - (#) During and just after reset, the alternate functions are not - active and the GPIO pins are configured in input floating mode (except JTAG - pins). - - (#) The LSE oscillator pins OSC32_IN and OSC32_OUT can be used as general purpose - (PC14 and PC15, respectively) when the LSE oscillator is off. The LSE has - priority over the GPIO function. - - (#) The HSE oscillator pins OSC_IN/OSC_OUT can be used as - general purpose PH0 and PH1, respectively, when the HSE oscillator is off. - The HSE has priority over the GPIO function. - - @endverbatim - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @defgroup GPIO GPIO - * @brief GPIO HAL module driver - * @{ - */ - -#ifdef HAL_GPIO_MODULE_ENABLED - -/* Private typedef -----------------------------------------------------------*/ -/* Private define ------------------------------------------------------------*/ -/** @addtogroup GPIO_Private_Constants GPIO Private Constants - * @{ - */ -#define GPIO_MODE ((uint32_t)0x00000003U) -#define EXTI_MODE ((uint32_t)0x10000000U) -#define GPIO_MODE_IT ((uint32_t)0x00010000U) -#define GPIO_MODE_EVT ((uint32_t)0x00020000U) -#define RISING_EDGE ((uint32_t)0x00100000U) -#define FALLING_EDGE ((uint32_t)0x00200000U) -#define GPIO_OUTPUT_TYPE ((uint32_t)0x00000010U) - -#define GPIO_NUMBER ((uint32_t)16U) -/** - * @} - */ -/* Private macro -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/* Private function prototypes -----------------------------------------------*/ -/* Private functions ---------------------------------------------------------*/ -/* Exported functions --------------------------------------------------------*/ -/** @defgroup GPIO_Exported_Functions GPIO Exported Functions - * @{ - */ - -/** @defgroup GPIO_Exported_Functions_Group1 Initialization and de-initialization functions - * @brief Initialization and Configuration functions - * -@verbatim - =============================================================================== - ##### Initialization and de-initialization functions ##### - =============================================================================== - [..] - This section provides functions allowing to initialize and de-initialize the GPIOs - to be ready for use. - -@endverbatim - * @{ - */ - - -/** - * @brief Initializes the GPIOx peripheral according to the specified parameters in the GPIO_Init. - * @param GPIOx: where x can be (A..K) to select the GPIO peripheral for STM32F429X device or - * x can be (A..I) to select the GPIO peripheral for STM32F40XX and STM32F427X devices. - * @param GPIO_Init: pointer to a GPIO_InitTypeDef structure that contains - * the configuration information for the specified GPIO peripheral. - * @retval None - */ -void HAL_GPIO_Init(GPIO_TypeDef* GPIOx, GPIO_InitTypeDef* GPIO_Init) -{ - uint32_t position; - uint32_t ioposition = 0x00U; - uint32_t iocurrent = 0x00U; - uint32_t temp = 0x00U; - /* Check the parameters */ - assert_param(IS_GPIO_ALL_INSTANCE(GPIOx)); - assert_param(IS_GPIO_PIN(GPIO_Init->Pin)); - assert_param(IS_GPIO_MODE(GPIO_Init->Mode)); - assert_param(IS_GPIO_PULL(GPIO_Init->Pull)); - - /* Configure the port pins */ - for (position = 0U; position < GPIO_NUMBER; position++) - { - /* Get the IO position */ - ioposition = ((uint32_t)0x01U) << position; - /* Get the current IO position */ - iocurrent = (uint32_t)(GPIO_Init->Pin) & ioposition; - - if (iocurrent == ioposition) - { - /*--------------------- GPIO Mode Configuration ------------------------*/ - /* In case of Alternate function mode selection */ - if ((GPIO_Init->Mode == GPIO_MODE_AF_PP) || (GPIO_Init->Mode == GPIO_MODE_AF_OD)) - { - /* Check the Alternate function parameter */ - assert_param(IS_GPIO_AF(GPIO_Init->Alternate)); - /* Configure Alternate function mapped with the current IO */ - temp = GPIOx->AFR[position >> 3U]; - temp &= ~((uint32_t)0xFU << ((uint32_t)(position & (uint32_t)0x07U) * 4U)) ; - temp |= ((uint32_t)(GPIO_Init->Alternate) << (((uint32_t)position & (uint32_t)0x07U) * 4U)); - GPIOx->AFR[position >> 3U] = temp; - } - - /* Configure IO Direction mode (Input, Output, Alternate or Analog) */ - temp = GPIOx->MODER; - temp &= ~(GPIO_MODER_MODER0 << (position * 2U)); - temp |= ((GPIO_Init->Mode & GPIO_MODE) << (position * 2U)); - GPIOx->MODER = temp; - - /* In case of Output or Alternate function mode selection */ - if ((GPIO_Init->Mode == GPIO_MODE_OUTPUT_PP) || (GPIO_Init->Mode == GPIO_MODE_AF_PP) || - (GPIO_Init->Mode == GPIO_MODE_OUTPUT_OD) || (GPIO_Init->Mode == GPIO_MODE_AF_OD)) - { - /* Check the Speed parameter */ - assert_param(IS_GPIO_SPEED(GPIO_Init->Speed)); - /* Configure the IO Speed */ - temp = GPIOx->OSPEEDR; - temp &= ~(GPIO_OSPEEDER_OSPEEDR0 << (position * 2U)); - temp |= (GPIO_Init->Speed << (position * 2U)); - GPIOx->OSPEEDR = temp; - /* Configure the IO Output Type */ - temp = GPIOx->OTYPER; - temp &= ~(GPIO_OTYPER_OT_0 << position) ; - temp |= (((GPIO_Init->Mode & GPIO_OUTPUT_TYPE) >> 4U) << position); - GPIOx->OTYPER = temp; - } - - /* Activate the Pull-up or Pull down resistor for the current IO */ - temp = GPIOx->PUPDR; - temp &= ~(GPIO_PUPDR_PUPDR0 << (position * 2U)); - temp |= ((GPIO_Init->Pull) << (position * 2U)); - GPIOx->PUPDR = temp; - - /*--------------------- EXTI Mode Configuration ------------------------*/ - /* Configure the External Interrupt or event for the current IO */ - if ((GPIO_Init->Mode & EXTI_MODE) == EXTI_MODE) - { - /* Enable SYSCFG Clock */ - __HAL_RCC_SYSCFG_CLK_ENABLE(); - temp = SYSCFG->EXTICR[position >> 2U]; - temp &= ~(((uint32_t)0x0FU) << (4U * (position & 0x03U))); - temp |= ((uint32_t)(GPIO_GET_INDEX(GPIOx)) << (4U * (position & 0x03U))); - SYSCFG->EXTICR[position >> 2U] = temp; - /* Clear EXTI line configuration */ - temp = EXTI->IMR; - temp &= ~((uint32_t)iocurrent); - - if ((GPIO_Init->Mode & GPIO_MODE_IT) == GPIO_MODE_IT) - { - temp |= iocurrent; - } - - EXTI->IMR = temp; - temp = EXTI->EMR; - temp &= ~((uint32_t)iocurrent); - - if ((GPIO_Init->Mode & GPIO_MODE_EVT) == GPIO_MODE_EVT) - { - temp |= iocurrent; - } - - EXTI->EMR = temp; - /* Clear Rising Falling edge configuration */ - temp = EXTI->RTSR; - temp &= ~((uint32_t)iocurrent); - - if ((GPIO_Init->Mode & RISING_EDGE) == RISING_EDGE) - { - temp |= iocurrent; - } - - EXTI->RTSR = temp; - temp = EXTI->FTSR; - temp &= ~((uint32_t)iocurrent); - - if ((GPIO_Init->Mode & FALLING_EDGE) == FALLING_EDGE) - { - temp |= iocurrent; - } - - EXTI->FTSR = temp; - } - } - } -} - -/** - * @brief De-initializes the GPIOx peripheral registers to their default reset values. - * @param GPIOx: where x can be (A..K) to select the GPIO peripheral for STM32F429X device or - * x can be (A..I) to select the GPIO peripheral for STM32F40XX and STM32F427X devices. - * @param GPIO_Pin: specifies the port bit to be written. - * This parameter can be one of GPIO_PIN_x where x can be (0..15). - * @retval None - */ -void HAL_GPIO_DeInit(GPIO_TypeDef* GPIOx, uint32_t GPIO_Pin) -{ - uint32_t position; - uint32_t ioposition = 0x00U; - uint32_t iocurrent = 0x00U; - uint32_t tmp = 0x00U; - /* Check the parameters */ - assert_param(IS_GPIO_ALL_INSTANCE(GPIOx)); - - /* Configure the port pins */ - for (position = 0U; position < GPIO_NUMBER; position++) - { - /* Get the IO position */ - ioposition = ((uint32_t)0x01U) << position; - /* Get the current IO position */ - iocurrent = (GPIO_Pin) & ioposition; - - if (iocurrent == ioposition) - { - /*------------------------- GPIO Mode Configuration --------------------*/ - /* Configure IO Direction in Input Floating Mode */ - GPIOx->MODER &= ~(GPIO_MODER_MODER0 << (position * 2U)); - /* Configure the default Alternate Function in current IO */ - GPIOx->AFR[position >> 3U] &= ~((uint32_t)0xFU << ((uint32_t)(position & (uint32_t)0x07U) * 4U)) ; - /* Configure the default value for IO Speed */ - GPIOx->OSPEEDR &= ~(GPIO_OSPEEDER_OSPEEDR0 << (position * 2U)); - /* Configure the default value IO Output Type */ - GPIOx->OTYPER &= ~(GPIO_OTYPER_OT_0 << position) ; - /* Deactivate the Pull-up and Pull-down resistor for the current IO */ - GPIOx->PUPDR &= ~(GPIO_PUPDR_PUPDR0 << (position * 2U)); - /*------------------------- EXTI Mode Configuration --------------------*/ - tmp = SYSCFG->EXTICR[position >> 2U]; - tmp &= (((uint32_t)0x0FU) << (4U * (position & 0x03U))); - - if (tmp == ((uint32_t)(GPIO_GET_INDEX(GPIOx)) << (4U * (position & 0x03U)))) - { - /* Configure the External Interrupt or event for the current IO */ - tmp = ((uint32_t)0x0FU) << (4U * (position & 0x03U)); - SYSCFG->EXTICR[position >> 2U] &= ~tmp; - /* Clear EXTI line configuration */ - EXTI->IMR &= ~((uint32_t)iocurrent); - EXTI->EMR &= ~((uint32_t)iocurrent); - /* Clear Rising Falling edge configuration */ - EXTI->RTSR &= ~((uint32_t)iocurrent); - EXTI->FTSR &= ~((uint32_t)iocurrent); - } - } - } -} - -/** - * @} - */ - -/** @defgroup GPIO_Exported_Functions_Group2 IO operation functions - * @brief GPIO Read and Write - * -@verbatim - =============================================================================== - ##### IO operation functions ##### - =============================================================================== - -@endverbatim - * @{ - */ - -/** - * @brief Reads the specified input port pin. - * @param GPIOx: where x can be (A..K) to select the GPIO peripheral for STM32F429X device or - * x can be (A..I) to select the GPIO peripheral for STM32F40XX and STM32F427X devices. - * @param GPIO_Pin: specifies the port bit to read. - * This parameter can be GPIO_PIN_x where x can be (0..15). - * @retval The input port pin value. - */ -GPIO_PinState HAL_GPIO_ReadPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin) -{ - GPIO_PinState bitstatus; - /* Check the parameters */ - assert_param(IS_GPIO_PIN(GPIO_Pin)); - - if ((GPIOx->IDR & GPIO_Pin) != (uint32_t)GPIO_PIN_RESET) - { - bitstatus = GPIO_PIN_SET; - } - else - { - bitstatus = GPIO_PIN_RESET; - } - - return bitstatus; -} - -/** - * @brief Sets or clears the selected data port bit. - * - * @note This function uses GPIOx_BSRR register to allow atomic read/modify - * accesses. In this way, there is no risk of an IRQ occurring between - * the read and the modify access. - * - * @param GPIOx: where x can be (A..K) to select the GPIO peripheral for STM32F429X device or - * x can be (A..I) to select the GPIO peripheral for STM32F40XX and STM32F427X devices. - * @param GPIO_Pin: specifies the port bit to be written. - * This parameter can be one of GPIO_PIN_x where x can be (0..15). - * @param PinState: specifies the value to be written to the selected bit. - * This parameter can be one of the GPIO_PinState enum values: - * @arg GPIO_PIN_RESET: to clear the port pin - * @arg GPIO_PIN_SET: to set the port pin - * @retval None - */ -void HAL_GPIO_WritePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState) -{ - /* Check the parameters */ - assert_param(IS_GPIO_PIN(GPIO_Pin)); - assert_param(IS_GPIO_PIN_ACTION(PinState)); - - if (PinState != GPIO_PIN_RESET) - { - GPIOx->BSRR = GPIO_Pin; - } - else - { - GPIOx->BSRR = (uint32_t)GPIO_Pin << 16U; - } -} - -/** - * @brief Toggles the specified GPIO pins. - * @param GPIOx: Where x can be (A..K) to select the GPIO peripheral for STM32F429X device or - * x can be (A..I) to select the GPIO peripheral for STM32F40XX and STM32F427X devices. - * @param GPIO_Pin: Specifies the pins to be toggled. - * @retval None - */ -void HAL_GPIO_TogglePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin) -{ - /* Check the parameters */ - assert_param(IS_GPIO_PIN(GPIO_Pin)); - GPIOx->ODR ^= GPIO_Pin; -} - -/** - * @brief Locks GPIO Pins configuration registers. - * @note The locked registers are GPIOx_MODER, GPIOx_OTYPER, GPIOx_OSPEEDR, - * GPIOx_PUPDR, GPIOx_AFRL and GPIOx_AFRH. - * @note The configuration of the locked GPIO pins can no longer be modified - * until the next reset. - * @param GPIOx: where x can be (A..F) to select the GPIO peripheral for STM32F4 family - * @param GPIO_Pin: specifies the port bit to be locked. - * This parameter can be any combination of GPIO_PIN_x where x can be (0..15). - * @retval None - */ -HAL_StatusTypeDef HAL_GPIO_LockPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin) -{ - __IO uint32_t tmp = GPIO_LCKR_LCKK; - /* Check the parameters */ - assert_param(IS_GPIO_PIN(GPIO_Pin)); - /* Apply lock key write sequence */ - tmp |= GPIO_Pin; - /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */ - GPIOx->LCKR = tmp; - /* Reset LCKx bit(s): LCKK='0' + LCK[15-0] */ - GPIOx->LCKR = GPIO_Pin; - /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */ - GPIOx->LCKR = tmp; - /* Read LCKK bit*/ - tmp = GPIOx->LCKR; - - if ((GPIOx->LCKR & GPIO_LCKR_LCKK) != RESET) - { - return HAL_OK; - } - else - { - return HAL_ERROR; - } -} - -/** - * @brief This function handles EXTI interrupt request. - * @param GPIO_Pin: Specifies the pins connected EXTI line - * @retval None - */ -void HAL_GPIO_EXTI_IRQHandler(uint16_t GPIO_Pin) -{ - /* EXTI line interrupt detected */ - if (__HAL_GPIO_EXTI_GET_IT(GPIO_Pin) != RESET) - { - __HAL_GPIO_EXTI_CLEAR_IT(GPIO_Pin); - HAL_GPIO_EXTI_Callback(GPIO_Pin); - } -} - -/** - * @brief EXTI line detection callbacks. - * @param GPIO_Pin: Specifies the pins connected EXTI line - * @retval None - */ -__weak void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin) -{ - /* Prevent unused argument(s) compilation warning */ - UNUSED(GPIO_Pin); - /* NOTE: This function Should not be modified, when the callback is needed, - the HAL_GPIO_EXTI_Callback could be implemented in the user file - */ -} - -/** - * @} - */ - - -/** - * @} - */ - -#endif /* HAL_GPIO_MODULE_ENABLED */ -/** - * @} - */ - -/** - * @} - */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr_ex.c b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr_ex.c deleted file mode 100644 index 6d8d5fdd..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr_ex.c +++ /dev/null @@ -1,628 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_pwr_ex.c - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Extended PWR HAL module driver. - * This file provides firmware functions to manage the following - * functionalities of PWR extension peripheral: - * + Peripheral Extended features functions - * - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @defgroup PWREx PWREx - * @brief PWR HAL module driver - * @{ - */ - -#ifdef HAL_PWR_MODULE_ENABLED - -/* Private typedef -----------------------------------------------------------*/ -/* Private define ------------------------------------------------------------*/ -/** @addtogroup PWREx_Private_Constants - * @{ - */ -#define PWR_OVERDRIVE_TIMEOUT_VALUE 1000U -#define PWR_UDERDRIVE_TIMEOUT_VALUE 1000U -#define PWR_BKPREG_TIMEOUT_VALUE 1000U -#define PWR_VOSRDY_TIMEOUT_VALUE 1000U -/** - * @} - */ - - -/* Private macro -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/* Private function prototypes -----------------------------------------------*/ -/* Private functions ---------------------------------------------------------*/ -/** @defgroup PWREx_Exported_Functions PWREx Exported Functions - * @{ - */ - -/** @defgroup PWREx_Exported_Functions_Group1 Peripheral Extended features functions - * @brief Peripheral Extended features functions - * -@verbatim - - =============================================================================== - ##### Peripheral extended features functions ##### - =============================================================================== - - *** Main and Backup Regulators configuration *** - ================================================ - [..] - (+) The backup domain includes 4 Kbytes of backup SRAM accessible only from - the CPU, and address in 32-bit, 16-bit or 8-bit mode. Its content is - retained even in Standby or VBAT mode when the low power backup regulator - is enabled. It can be considered as an internal EEPROM when VBAT is - always present. You can use the HAL_PWREx_EnableBkUpReg() function to - enable the low power backup regulator. - - (+) When the backup domain is supplied by VDD (analog switch connected to VDD) - the backup SRAM is powered from VDD which replaces the VBAT power supply to - save battery life. - - (+) The backup SRAM is not mass erased by a tamper event. It is read - protected to prevent confidential data, such as cryptographic private - key, from being accessed. The backup SRAM can be erased only through - the Flash interface when a protection level change from level 1 to - level 0 is requested. - -@- Refer to the description of Read protection (RDP) in the Flash - programming manual. - - (+) The main internal regulator can be configured to have a tradeoff between - performance and power consumption when the device does not operate at - the maximum frequency. This is done through __HAL_PWR_MAINREGULATORMODE_CONFIG() - macro which configure VOS bit in PWR_CR register - - Refer to the product datasheets for more details. - - *** FLASH Power Down configuration **** - ======================================= - [..] - (+) By setting the FPDS bit in the PWR_CR register by using the - HAL_PWREx_EnableFlashPowerDown() function, the Flash memory also enters power - down mode when the device enters Stop mode. When the Flash memory - is in power down mode, an additional startup delay is incurred when - waking up from Stop mode. - - (+) For STM32F42xxx/43xxx/446xx/469xx/479xx Devices, the scale can be modified only when the PLL - is OFF and the HSI or HSE clock source is selected as system clock. - The new value programmed is active only when the PLL is ON. - When the PLL is OFF, the voltage scale 3 is automatically selected. - Refer to the datasheets for more details. - - *** Over-Drive and Under-Drive configuration **** - ================================================= - [..] - (+) For STM32F42xxx/43xxx/446xx/469xx/479xx Devices, in Run mode: the main regulator has - 2 operating modes available: - (++) Normal mode: The CPU and core logic operate at maximum frequency at a given - voltage scaling (scale 1, scale 2 or scale 3) - (++) Over-drive mode: This mode allows the CPU and the core logic to operate at a - higher frequency than the normal mode for a given voltage scaling (scale 1, - scale 2 or scale 3). This mode is enabled through HAL_PWREx_EnableOverDrive() function and - disabled by HAL_PWREx_DisableOverDrive() function, to enter or exit from Over-drive mode please follow - the sequence described in Reference manual. - - (+) For STM32F42xxx/43xxx/446xx/469xx/479xx Devices, in Stop mode: the main regulator or low power regulator - supplies a low power voltage to the 1.2V domain, thus preserving the content of registers - and internal SRAM. 2 operating modes are available: - (++) Normal mode: the 1.2V domain is preserved in nominal leakage mode. This mode is only - available when the main regulator or the low power regulator is used in Scale 3 or - low voltage mode. - (++) Under-drive mode: the 1.2V domain is preserved in reduced leakage mode. This mode is only - available when the main regulator or the low power regulator is in low voltage mode. - -@endverbatim - * @{ - */ - -/** - * @brief Enables the Backup Regulator. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_PWREx_EnableBkUpReg(void) -{ - uint32_t tickstart = 0U; - *(__IO uint32_t*) CSR_BRE_BB = (uint32_t)ENABLE; - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till Backup regulator ready flag is set */ - while (__HAL_PWR_GET_FLAG(PWR_FLAG_BRR) == RESET) - { - if ((HAL_GetTick() - tickstart ) > PWR_BKPREG_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - return HAL_OK; -} - -/** - * @brief Disables the Backup Regulator. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_PWREx_DisableBkUpReg(void) -{ - uint32_t tickstart = 0U; - *(__IO uint32_t*) CSR_BRE_BB = (uint32_t)DISABLE; - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till Backup regulator ready flag is set */ - while (__HAL_PWR_GET_FLAG(PWR_FLAG_BRR) != RESET) - { - if ((HAL_GetTick() - tickstart ) > PWR_BKPREG_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - return HAL_OK; -} - -/** - * @brief Enables the Flash Power Down in Stop mode. - * @retval None - */ -void HAL_PWREx_EnableFlashPowerDown(void) -{ - *(__IO uint32_t*) CR_FPDS_BB = (uint32_t)ENABLE; -} - -/** - * @brief Disables the Flash Power Down in Stop mode. - * @retval None - */ -void HAL_PWREx_DisableFlashPowerDown(void) -{ - *(__IO uint32_t*) CR_FPDS_BB = (uint32_t)DISABLE; -} - -/** - * @brief Return Voltage Scaling Range. - * @retval The configured scale for the regulator voltage(VOS bit field). - * The returned value can be one of the following: - * - @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode - * - @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode - * - @arg PWR_REGULATOR_VOLTAGE_SCALE3: Regulator voltage output Scale 3 mode - */ -uint32_t HAL_PWREx_GetVoltageRange(void) -{ - return (PWR->CR & PWR_CR_VOS); -} - -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) -/** - * @brief Configures the main internal regulator output voltage. - * @param VoltageScaling: specifies the regulator output voltage to achieve - * a tradeoff between performance and power consumption. - * This parameter can be one of the following values: - * @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output range 1 mode, - * the maximum value of fHCLK = 168 MHz. - * @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output range 2 mode, - * the maximum value of fHCLK = 144 MHz. - * @note When moving from Range 1 to Range 2, the system frequency must be decreased to - * a value below 144 MHz before calling HAL_PWREx_ConfigVoltageScaling() API. - * When moving from Range 2 to Range 1, the system frequency can be increased to - * a value up to 168 MHz after calling HAL_PWREx_ConfigVoltageScaling() API. - * @retval HAL Status - */ -HAL_StatusTypeDef HAL_PWREx_ControlVoltageScaling(uint32_t VoltageScaling) -{ - uint32_t tickstart = 0U; - assert_param(IS_PWR_VOLTAGE_SCALING_RANGE(VoltageScaling)); - /* Enable PWR RCC Clock Peripheral */ - __HAL_RCC_PWR_CLK_ENABLE(); - /* Set Range */ - __HAL_PWR_VOLTAGESCALING_CONFIG(VoltageScaling); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - while ((__HAL_PWR_GET_FLAG(PWR_FLAG_VOSRDY) == RESET)) - { - if ((HAL_GetTick() - tickstart ) > PWR_VOSRDY_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - return HAL_OK; -} - -#elif defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) || \ - defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F469xx) || \ - defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || \ - defined(STM32F412Cx) -/** - * @brief Configures the main internal regulator output voltage. - * @param VoltageScaling: specifies the regulator output voltage to achieve - * a tradeoff between performance and power consumption. - * This parameter can be one of the following values: - * @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output range 1 mode, - * the maximum value of fHCLK is 168 MHz. It can be extended to - * 180 MHz by activating the over-drive mode. - * @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output range 2 mode, - * the maximum value of fHCLK is 144 MHz. It can be extended to, - * 168 MHz by activating the over-drive mode. - * @arg PWR_REGULATOR_VOLTAGE_SCALE3: Regulator voltage output range 3 mode, - * the maximum value of fHCLK is 120 MHz. - * @note To update the system clock frequency(SYSCLK): - * - Set the HSI or HSE as system clock frequency using the HAL_RCC_ClockConfig(). - * - Call the HAL_RCC_OscConfig() to configure the PLL. - * - Call HAL_PWREx_ConfigVoltageScaling() API to adjust the voltage scale. - * - Set the new system clock frequency using the HAL_RCC_ClockConfig(). - * @note The scale can be modified only when the HSI or HSE clock source is selected - * as system clock source, otherwise the API returns HAL_ERROR. - * @note When the PLL is OFF, the voltage scale 3 is automatically selected and the VOS bits - * value in the PWR_CR1 register are not taken in account. - * @note This API forces the PLL state ON to allow the possibility to configure the voltage scale 1 or 2. - * @note The new voltage scale is active only when the PLL is ON. - * @retval HAL Status - */ -HAL_StatusTypeDef HAL_PWREx_ControlVoltageScaling(uint32_t VoltageScaling) -{ - uint32_t tickstart = 0U; - assert_param(IS_PWR_VOLTAGE_SCALING_RANGE(VoltageScaling)); - /* Enable PWR RCC Clock Peripheral */ - __HAL_RCC_PWR_CLK_ENABLE(); - - /* Check if the PLL is used as system clock or not */ - if (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_PLL) - { - /* Disable the main PLL */ - __HAL_RCC_PLL_DISABLE(); - /* Get Start Tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLL is disabled */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Set Range */ - __HAL_PWR_VOLTAGESCALING_CONFIG(VoltageScaling); - /* Enable the main PLL */ - __HAL_RCC_PLL_ENABLE(); - /* Get Start Tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLL is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Get Start Tick */ - tickstart = HAL_GetTick(); - - while ((__HAL_PWR_GET_FLAG(PWR_FLAG_VOSRDY) == RESET)) - { - if ((HAL_GetTick() - tickstart ) > PWR_VOSRDY_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - else - { - return HAL_ERROR; - } - - return HAL_OK; -} -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx */ - -#if defined(STM32F469xx) || defined(STM32F479xx) -/** - * @brief Enables Wakeup Pin Detection on high level (rising edge). - * @retval None - */ -void HAL_PWREx_EnableWakeUpPinPolarityRisingEdge(void) -{ - *(__IO uint32_t*) CSR_WUPP_BB = (uint32_t)DISABLE; -} - -/** - * @brief Enables Wakeup Pin Detection on low level (falling edge). - * @retval None - */ -void HAL_PWREx_EnableWakeUpPinPolarityFallingEdge(void) -{ - *(__IO uint32_t*) CSR_WUPP_BB = (uint32_t)ENABLE; -} -#endif /* STM32F469xx || STM32F479xx */ - -#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) ||\ - defined(STM32F411xE) || defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -/** - * @brief Enables Main Regulator low voltage mode. - * @note This mode is only available for STM32F401xx/STM32F410xx/STM32F411xx/STM32F412Zx/STM32F412Rx/STM32F412Vx/STM32F412Cx devices. - * @retval None - */ -void HAL_PWREx_EnableMainRegulatorLowVoltage(void) -{ - *(__IO uint32_t*) CR_MRLVDS_BB = (uint32_t)ENABLE; -} - -/** - * @brief Disables Main Regulator low voltage mode. - * @note This mode is only available for STM32F401xx/STM32F410xx/STM32F411xx/STM32F412Zx/STM32F412Rx/STM32F412Vx/STM32F412Cx devices. - * @retval None - */ -void HAL_PWREx_DisableMainRegulatorLowVoltage(void) -{ - *(__IO uint32_t*) CR_MRLVDS_BB = (uint32_t)DISABLE; -} - -/** - * @brief Enables Low Power Regulator low voltage mode. - * @note This mode is only available for STM32F401xx/STM32F410xx/STM32F411xx/STM32F412Zx/STM32F412Rx/STM32F412Vx/STM32F412Cx devices. - * @retval None - */ -void HAL_PWREx_EnableLowRegulatorLowVoltage(void) -{ - *(__IO uint32_t*) CR_LPLVDS_BB = (uint32_t)ENABLE; -} - -/** - * @brief Disables Low Power Regulator low voltage mode. - * @note This mode is only available for STM32F401xx/STM32F410xx/STM32F411xx/STM32F412Zx/STM32F412Rx/STM32F412Vx/STM32F412Cx devices. - * @retval None - */ -void HAL_PWREx_DisableLowRegulatorLowVoltage(void) -{ - *(__IO uint32_t*) CR_LPLVDS_BB = (uint32_t)DISABLE; -} - -#endif /* STM32F401xC || STM32F401xE || STM32F410xx || STM32F411xE || STM32F412Zx || STM32F412Rx || STM32F412Vx || STM32F412Cx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ - defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) -/** - * @brief Activates the Over-Drive mode. - * @note This function can be used only for STM32F42xx/STM32F43xx/STM32F446xx/STM32F469xx/STM32F479xx devices. - * This mode allows the CPU and the core logic to operate at a higher frequency - * than the normal mode for a given voltage scaling (scale 1, scale 2 or scale 3). - * @note It is recommended to enter or exit Over-drive mode when the application is not running - * critical tasks and when the system clock source is either HSI or HSE. - * During the Over-drive switch activation, no peripheral clocks should be enabled. - * The peripheral clocks must be enabled once the Over-drive mode is activated. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_PWREx_EnableOverDrive(void) -{ - uint32_t tickstart = 0U; - __HAL_RCC_PWR_CLK_ENABLE(); - /* Enable the Over-drive to extend the clock frequency to 180 Mhz */ - __HAL_PWR_OVERDRIVE_ENABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - while (!__HAL_PWR_GET_FLAG(PWR_FLAG_ODRDY)) - { - if ((HAL_GetTick() - tickstart) > PWR_OVERDRIVE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Enable the Over-drive switch */ - __HAL_PWR_OVERDRIVESWITCHING_ENABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - while (!__HAL_PWR_GET_FLAG(PWR_FLAG_ODSWRDY)) - { - if ((HAL_GetTick() - tickstart ) > PWR_OVERDRIVE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - return HAL_OK; -} - -/** - * @brief Deactivates the Over-Drive mode. - * @note This function can be used only for STM32F42xx/STM32F43xx/STM32F446xx/STM32F469xx/STM32F479xx devices. - * This mode allows the CPU and the core logic to operate at a higher frequency - * than the normal mode for a given voltage scaling (scale 1, scale 2 or scale 3). - * @note It is recommended to enter or exit Over-drive mode when the application is not running - * critical tasks and when the system clock source is either HSI or HSE. - * During the Over-drive switch activation, no peripheral clocks should be enabled. - * The peripheral clocks must be enabled once the Over-drive mode is activated. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_PWREx_DisableOverDrive(void) -{ - uint32_t tickstart = 0U; - __HAL_RCC_PWR_CLK_ENABLE(); - /* Disable the Over-drive switch */ - __HAL_PWR_OVERDRIVESWITCHING_DISABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - while (__HAL_PWR_GET_FLAG(PWR_FLAG_ODSWRDY)) - { - if ((HAL_GetTick() - tickstart) > PWR_OVERDRIVE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Disable the Over-drive */ - __HAL_PWR_OVERDRIVE_DISABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - while (__HAL_PWR_GET_FLAG(PWR_FLAG_ODRDY)) - { - if ((HAL_GetTick() - tickstart) > PWR_OVERDRIVE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - return HAL_OK; -} - -/** - * @brief Enters in Under-Drive STOP mode. - * - * @note This mode is only available for STM32F42xxx/STM324F3xxx/STM32F446xx/STM32F469xx/STM32F479xx devices. - * - * @note This mode can be selected only when the Under-Drive is already active - * - * @note This mode is enabled only with STOP low power mode. - * In this mode, the 1.2V domain is preserved in reduced leakage mode. This - * mode is only available when the main regulator or the low power regulator - * is in low voltage mode - * - * @note If the Under-drive mode was enabled, it is automatically disabled after - * exiting Stop mode. - * When the voltage regulator operates in Under-drive mode, an additional - * startup delay is induced when waking up from Stop mode. - * - * @note In Stop mode, all I/O pins keep the same state as in Run mode. - * - * @note When exiting Stop mode by issuing an interrupt or a wake-up event, - * the HSI RC oscillator is selected as system clock. - * - * @note When the voltage regulator operates in low power mode, an additional - * startup delay is incurred when waking up from Stop mode. - * By keeping the internal regulator ON during Stop mode, the consumption - * is higher although the startup time is reduced. - * - * @param Regulator: specifies the regulator state in STOP mode. - * This parameter can be one of the following values: - * @arg PWR_MAINREGULATOR_UNDERDRIVE_ON: Main Regulator in under-drive mode - * and Flash memory in power-down when the device is in Stop under-drive mode - * @arg PWR_LOWPOWERREGULATOR_UNDERDRIVE_ON: Low Power Regulator in under-drive mode - * and Flash memory in power-down when the device is in Stop under-drive mode - * @param STOPEntry: specifies if STOP mode in entered with WFI or WFE instruction. - * This parameter can be one of the following values: - * @arg PWR_SLEEPENTRY_WFI: enter STOP mode with WFI instruction - * @arg PWR_SLEEPENTRY_WFE: enter STOP mode with WFE instruction - * @retval None - */ -HAL_StatusTypeDef HAL_PWREx_EnterUnderDriveSTOPMode(uint32_t Regulator, uint8_t STOPEntry) -{ - uint32_t tmpreg1 = 0U; - uint32_t tickstart = 0U; - /* Check the parameters */ - assert_param(IS_PWR_REGULATOR_UNDERDRIVE(Regulator)); - assert_param(IS_PWR_STOP_ENTRY(STOPEntry)); - /* Enable Power ctrl clock */ - __HAL_RCC_PWR_CLK_ENABLE(); - /* Enable the Under-drive Mode ---------------------------------------------*/ - /* Clear Under-drive flag */ - __HAL_PWR_CLEAR_ODRUDR_FLAG(); - /* Enable the Under-drive */ - __HAL_PWR_UNDERDRIVE_ENABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait for UnderDrive mode is ready */ - while (__HAL_PWR_GET_FLAG(PWR_FLAG_UDRDY)) - { - if ((HAL_GetTick() - tickstart) > PWR_UDERDRIVE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Select the regulator state in STOP mode ---------------------------------*/ - tmpreg1 = PWR->CR; - /* Clear PDDS, LPDS, MRLUDS and LPLUDS bits */ - tmpreg1 &= (uint32_t)~(PWR_CR_PDDS | PWR_CR_LPDS | PWR_CR_LPUDS | PWR_CR_MRUDS); - /* Set LPDS, MRLUDS and LPLUDS bits according to PWR_Regulator value */ - tmpreg1 |= Regulator; - /* Store the new value */ - PWR->CR = tmpreg1; - /* Set SLEEPDEEP bit of Cortex System Control Register */ - SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk; - - /* Select STOP mode entry --------------------------------------------------*/ - if (STOPEntry == PWR_SLEEPENTRY_WFI) - { - /* Request Wait For Interrupt */ - __WFI(); - } - else - { - /* Request Wait For Event */ - __WFE(); - } - - /* Reset SLEEPDEEP bit of Cortex System Control Register */ - SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP_Msk); - return HAL_OK; -} - -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */ -/** - * @} - */ - -/** - * @} - */ - -#endif /* HAL_PWR_MODULE_ENABLED */ -/** - * @} - */ - -/** - * @} - */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c deleted file mode 100644 index 92ec07df..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c +++ /dev/null @@ -1,1097 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_rcc.c - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief RCC HAL module driver. - * This file provides firmware functions to manage the following - * functionalities of the Reset and Clock Control (RCC) peripheral: - * + Initialization and de-initialization functions - * + Peripheral Control functions - * - @verbatim - ============================================================================== - ##### RCC specific features ##### - ============================================================================== - [..] - After reset the device is running from Internal High Speed oscillator - (HSI 16MHz) with Flash 0 wait state, Flash prefetch buffer, D-Cache - and I-Cache are disabled, and all peripherals are off except internal - SRAM, Flash and JTAG. - (+) There is no prescaler on High speed (AHB) and Low speed (APB) busses; - all peripherals mapped on these busses are running at HSI speed. - (+) The clock for all peripherals is switched off, except the SRAM and FLASH. - (+) All GPIOs are in input floating state, except the JTAG pins which - are assigned to be used for debug purpose. - - [..] - Once the device started from reset, the user application has to: - (+) Configure the clock source to be used to drive the System clock - (if the application needs higher frequency/performance) - (+) Configure the System clock frequency and Flash settings - (+) Configure the AHB and APB busses prescalers - (+) Enable the clock for the peripheral(s) to be used - (+) Configure the clock source(s) for peripherals which clocks are not - derived from the System clock (I2S, RTC, ADC, USB OTG FS/SDIO/RNG) - - ##### RCC Limitations ##### - ============================================================================== - [..] - A delay between an RCC peripheral clock enable and the effective peripheral - enabling should be taken into account in order to manage the peripheral read/write - from/to registers. - (+) This delay depends on the peripheral mapping. - (+) If peripheral is mapped on AHB: the delay is 2 AHB clock cycle - after the clock enable bit is set on the hardware register - (+) If peripheral is mapped on APB: the delay is 2 APB clock cycle - after the clock enable bit is set on the hardware register - - [..] - Implemented Workaround: - (+) For AHB & APB peripherals, a dummy read to the peripheral register has been - inserted in each __HAL_RCC_PPP_CLK_ENABLE() macro. - - @endverbatim - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @defgroup RCC RCC - * @brief RCC HAL module driver - * @{ - */ - -#ifdef HAL_RCC_MODULE_ENABLED - -/* Private typedef -----------------------------------------------------------*/ -/* Private define ------------------------------------------------------------*/ -/** @addtogroup RCC_Private_Constants - * @{ - */ -#define CLOCKSWITCH_TIMEOUT_VALUE ((uint32_t)5000U) /* 5 s */ - -/* Private macro -------------------------------------------------------------*/ -#define __MCO1_CLK_ENABLE() __HAL_RCC_GPIOA_CLK_ENABLE() -#define MCO1_GPIO_PORT GPIOA -#define MCO1_PIN GPIO_PIN_8 - -#define __MCO2_CLK_ENABLE() __HAL_RCC_GPIOC_CLK_ENABLE() -#define MCO2_GPIO_PORT GPIOC -#define MCO2_PIN GPIO_PIN_9 -/** - * @} - */ - -/* Private variables ---------------------------------------------------------*/ -/** @defgroup RCC_Private_Variables RCC Private Variables - * @{ - */ -const uint8_t APBAHBPrescTable[16] = {0U, 0U, 0U, 0U, 1U, 2U, 3U, 4U, 1U, 2U, 3U, 4U, 6U, 7U, 8U, 9U}; -/** - * @} - */ - -/* Private function prototypes -----------------------------------------------*/ -/* Private functions ---------------------------------------------------------*/ - -/** @defgroup RCC_Exported_Functions RCC Exported Functions - * @{ - */ - -/** @defgroup RCC_Exported_Functions_Group1 Initialization and de-initialization functions - * @brief Initialization and Configuration functions - * -@verbatim - =============================================================================== - ##### Initialization and de-initialization functions ##### - =============================================================================== - [..] - This section provides functions allowing to configure the internal/external oscillators - (HSE, HSI, LSE, LSI, PLL, CSS and MCO) and the System busses clocks (SYSCLK, AHB, APB1 - and APB2). - - [..] Internal/external clock and PLL configuration - (#) HSI (high-speed internal), 16 MHz factory-trimmed RC used directly or through - the PLL as System clock source. - - (#) LSI (low-speed internal), 32 KHz low consumption RC used as IWDG and/or RTC - clock source. - - (#) HSE (high-speed external), 4 to 26 MHz crystal oscillator used directly or - through the PLL as System clock source. Can be used also as RTC clock source. - - (#) LSE (low-speed external), 32 KHz oscillator used as RTC clock source. - - (#) PLL (clocked by HSI or HSE), featuring two different output clocks: - (++) The first output is used to generate the high speed system clock (up to 168 MHz) - (++) The second output is used to generate the clock for the USB OTG FS (48 MHz), - the random analog generator (<=48 MHz) and the SDIO (<= 48 MHz). - - (#) CSS (Clock security system), once enable using the macro __HAL_RCC_CSS_ENABLE() - and if a HSE clock failure occurs(HSE used directly or through PLL as System - clock source), the System clocks automatically switched to HSI and an interrupt - is generated if enabled. The interrupt is linked to the Cortex-M4 NMI - (Non-Maskable Interrupt) exception vector. - - (#) MCO1 (microcontroller clock output), used to output HSI, LSE, HSE or PLL - clock (through a configurable prescaler) on PA8 pin. - - (#) MCO2 (microcontroller clock output), used to output HSE, PLL, SYSCLK or PLLI2S - clock (through a configurable prescaler) on PC9 pin. - - [..] System, AHB and APB busses clocks configuration - (#) Several clock sources can be used to drive the System clock (SYSCLK): HSI, - HSE and PLL. - The AHB clock (HCLK) is derived from System clock through configurable - prescaler and used to clock the CPU, memory and peripherals mapped - on AHB bus (DMA, GPIO...). APB1 (PCLK1) and APB2 (PCLK2) clocks are derived - from AHB clock through configurable prescalers and used to clock - the peripherals mapped on these busses. You can use - "HAL_RCC_GetSysClockFreq()" function to retrieve the frequencies of these clocks. - - (#) For the STM32F405xx/07xx and STM32F415xx/17xx devices, the maximum - frequency of the SYSCLK and HCLK is 168 MHz, PCLK2 84 MHz and PCLK1 42 MHz. - Depending on the device voltage range, the maximum frequency should - be adapted accordingly (refer to the product datasheets for more details). - - (#) For the STM32F42xxx, STM32F43xxx, STM32F446xx, STM32F469xx and STM32F479xx devices, - the maximum frequency of the SYSCLK and HCLK is 180 MHz, PCLK2 90 MHz and PCLK1 45 MHz. - Depending on the device voltage range, the maximum frequency should - be adapted accordingly (refer to the product datasheets for more details). - - (#) For the STM32F401xx, the maximum frequency of the SYSCLK and HCLK is 84 MHz, - PCLK2 84 MHz and PCLK1 42 MHz. - Depending on the device voltage range, the maximum frequency should - be adapted accordingly (refer to the product datasheets for more details). - - (#) For the STM32F41xxx, the maximum frequency of the SYSCLK and HCLK is 100 MHz, - PCLK2 100 MHz and PCLK1 50 MHz. - Depending on the device voltage range, the maximum frequency should - be adapted accordingly (refer to the product datasheets for more details). - -@endverbatim - * @{ - */ - -/** - * @brief Resets the RCC clock configuration to the default reset state. - * @note The default reset state of the clock configuration is given below: - * - HSI ON and used as system clock source - * - HSE and PLL OFF - * - AHB, APB1 and APB2 prescaler set to 1. - * - CSS, MCO1 and MCO2 OFF - * - All interrupts disabled - * @note This function doesn't modify the configuration of the - * - Peripheral clocks - * - LSI, LSE and RTC clocks - * @retval None - */ -__weak void HAL_RCC_DeInit(void) -{} - -/** - * @brief Initializes the RCC Oscillators according to the specified parameters in the - * RCC_OscInitTypeDef. - * @param RCC_OscInitStruct: pointer to an RCC_OscInitTypeDef structure that - * contains the configuration information for the RCC Oscillators. - * @note The PLL is not disabled when used as system clock. - * @note Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not - * supported by this API. User should request a transition to LSE Off - * first and then LSE On or LSE Bypass. - * @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not - * supported by this API. User should request a transition to HSE Off - * first and then HSE On or HSE Bypass. - * @retval HAL status - */ -__weak HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef* RCC_OscInitStruct) -{ - uint32_t tickstart = 0U; - /* Check the parameters */ - assert_param(IS_RCC_OSCILLATORTYPE(RCC_OscInitStruct->OscillatorType)); - - /*------------------------------- HSE Configuration ------------------------*/ - if (((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) - { - /* Check the parameters */ - assert_param(IS_RCC_HSE(RCC_OscInitStruct->HSEState)); - - /* When the HSE is used as system clock or clock source for PLL in these cases HSE will not disabled */ - if ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSE) || \ - ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSE))) - { - if ((__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) && (RCC_OscInitStruct->HSEState == RCC_HSE_OFF)) - { - return HAL_ERROR; - } - } - else - { - /* Set the new HSE configuration ---------------------------------------*/ - __HAL_RCC_HSE_CONFIG(RCC_OscInitStruct->HSEState); - - /* Check the HSE State */ - if ((RCC_OscInitStruct->HSEState) != RCC_HSE_OFF) - { - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till HSE is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - else - { - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till HSE is bypassed or disabled */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - } - - /*----------------------------- HSI Configuration --------------------------*/ - if (((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) - { - /* Check the parameters */ - assert_param(IS_RCC_HSI(RCC_OscInitStruct->HSIState)); - assert_param(IS_RCC_CALIBRATION_VALUE(RCC_OscInitStruct->HSICalibrationValue)); - - /* Check if HSI is used as system clock or as PLL source when PLL is selected as system clock */ - if ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSI) || \ - ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSI))) - { - /* When HSI is used as system clock it will not disabled */ - if ((__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) && (RCC_OscInitStruct->HSIState != RCC_HSI_ON)) - { - return HAL_ERROR; - } - /* Otherwise, just the calibration is allowed */ - else - { - /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ - __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); - } - } - else - { - /* Check the HSI State */ - if ((RCC_OscInitStruct->HSIState) != RCC_HSI_OFF) - { - /* Enable the Internal High Speed oscillator (HSI). */ - __HAL_RCC_HSI_ENABLE(); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till HSI is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ - __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); - } - else - { - /* Disable the Internal High Speed oscillator (HSI). */ - __HAL_RCC_HSI_DISABLE(); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till HSI is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - } - - /*------------------------------ LSI Configuration -------------------------*/ - if (((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) - { - /* Check the parameters */ - assert_param(IS_RCC_LSI(RCC_OscInitStruct->LSIState)); - - /* Check the LSI State */ - if ((RCC_OscInitStruct->LSIState) != RCC_LSI_OFF) - { - /* Enable the Internal Low Speed oscillator (LSI). */ - __HAL_RCC_LSI_ENABLE(); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till LSI is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - else - { - /* Disable the Internal Low Speed oscillator (LSI). */ - __HAL_RCC_LSI_DISABLE(); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till LSI is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - - /*------------------------------ LSE Configuration -------------------------*/ - if (((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE) - { - /* Check the parameters */ - assert_param(IS_RCC_LSE(RCC_OscInitStruct->LSEState)); - /* Enable Power Clock*/ - __HAL_RCC_PWR_CLK_ENABLE(); - /* Enable write access to Backup domain */ - PWR->CR |= PWR_CR_DBP; - /* Wait for Backup domain Write protection enable */ - tickstart = HAL_GetTick(); - - while ((PWR->CR & PWR_CR_DBP) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Set the new LSE configuration -----------------------------------------*/ - __HAL_RCC_LSE_CONFIG(RCC_OscInitStruct->LSEState); - - /* Check the LSE State */ - if ((RCC_OscInitStruct->LSEState) != RCC_LSE_OFF) - { - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till LSE is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - else - { - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till LSE is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - - /*-------------------------------- PLL Configuration -----------------------*/ - /* Check the parameters */ - assert_param(IS_RCC_PLL(RCC_OscInitStruct->PLL.PLLState)); - - if ((RCC_OscInitStruct->PLL.PLLState) != RCC_PLL_NONE) - { - /* Check if the PLL is used as system clock or not */ - if (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_PLL) - { - if ((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_ON) - { - /* Check the parameters */ - assert_param(IS_RCC_PLLSOURCE(RCC_OscInitStruct->PLL.PLLSource)); - assert_param(IS_RCC_PLLM_VALUE(RCC_OscInitStruct->PLL.PLLM)); - assert_param(IS_RCC_PLLN_VALUE(RCC_OscInitStruct->PLL.PLLN)); - assert_param(IS_RCC_PLLP_VALUE(RCC_OscInitStruct->PLL.PLLP)); - assert_param(IS_RCC_PLLQ_VALUE(RCC_OscInitStruct->PLL.PLLQ)); - /* Disable the main PLL. */ - __HAL_RCC_PLL_DISABLE(); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till PLL is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Configure the main PLL clock source, multiplication and division factors. */ - WRITE_REG(RCC->PLLCFGR, (RCC_OscInitStruct->PLL.PLLSource | \ - RCC_OscInitStruct->PLL.PLLM | \ - (RCC_OscInitStruct->PLL.PLLN << POSITION_VAL(RCC_PLLCFGR_PLLN)) | \ - (((RCC_OscInitStruct->PLL.PLLP >> 1U) - 1U) << POSITION_VAL(RCC_PLLCFGR_PLLP)) | \ - (RCC_OscInitStruct->PLL.PLLQ << POSITION_VAL(RCC_PLLCFGR_PLLQ)))); - /* Enable the main PLL. */ - __HAL_RCC_PLL_ENABLE(); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till PLL is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - else - { - /* Disable the main PLL. */ - __HAL_RCC_PLL_DISABLE(); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till PLL is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - else - { - return HAL_ERROR; - } - } - - return HAL_OK; -} - -/** - * @brief Initializes the CPU, AHB and APB busses clocks according to the specified - * parameters in the RCC_ClkInitStruct. - * @param RCC_ClkInitStruct: pointer to an RCC_OscInitTypeDef structure that - * contains the configuration information for the RCC peripheral. - * @param FLatency: FLASH Latency, this parameter depend on device selected - * - * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency - * and updated by HAL_RCC_GetHCLKFreq() function called within this function - * - * @note The HSI is used (enabled by hardware) as system clock source after - * startup from Reset, wake-up from STOP and STANDBY mode, or in case - * of failure of the HSE used directly or indirectly as system clock - * (if the Clock Security System CSS is enabled). - * - * @note A switch from one clock source to another occurs only if the target - * clock source is ready (clock stable after startup delay or PLL locked). - * If a clock source which is not yet ready is selected, the switch will - * occur when the clock source will be ready. - * - * @note Depending on the device voltage range, the software has to set correctly - * HPRE[3:0] bits to ensure that HCLK not exceed the maximum allowed frequency - * (for more details refer to section above "Initialization/de-initialization functions") - * @retval None - */ -HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef* RCC_ClkInitStruct, uint32_t FLatency) -{ - uint32_t tickstart = 0U; - /* Check the parameters */ - assert_param(IS_RCC_CLOCKTYPE(RCC_ClkInitStruct->ClockType)); - assert_param(IS_FLASH_LATENCY(FLatency)); - - /* To correctly read data from FLASH memory, the number of wait states (LATENCY) - must be correctly programmed according to the frequency of the CPU clock - (HCLK) and the supply voltage of the device. */ - - /* Increasing the number of wait states because of higher CPU frequency */ - if (FLatency > (FLASH->ACR & FLASH_ACR_LATENCY)) - { - /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */ - __HAL_FLASH_SET_LATENCY(FLatency); - - /* Check that the new number of wait states is taken into account to access the Flash - memory by reading the FLASH_ACR register */ - if ((FLASH->ACR & FLASH_ACR_LATENCY) != FLatency) - { - return HAL_ERROR; - } - } - - /*-------------------------- HCLK Configuration --------------------------*/ - if (((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK) - { - assert_param(IS_RCC_HCLK(RCC_ClkInitStruct->AHBCLKDivider)); - MODIFY_REG(RCC->CFGR, RCC_CFGR_HPRE, RCC_ClkInitStruct->AHBCLKDivider); - } - - /*------------------------- SYSCLK Configuration ---------------------------*/ - if (((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK) - { - assert_param(IS_RCC_SYSCLKSOURCE(RCC_ClkInitStruct->SYSCLKSource)); - - /* HSE is selected as System Clock Source */ - if (RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE) - { - /* Check the HSE ready flag */ - if (__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) - { - return HAL_ERROR; - } - } - /* PLL is selected as System Clock Source */ - else if ((RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK) || - (RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLRCLK)) - { - /* Check the PLL ready flag */ - if (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) - { - return HAL_ERROR; - } - } - /* HSI is selected as System Clock Source */ - else - { - /* Check the HSI ready flag */ - if (__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) - { - return HAL_ERROR; - } - } - - __HAL_RCC_SYSCLK_CONFIG(RCC_ClkInitStruct->SYSCLKSource); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - if (RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE) - { - while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSE) - { - if ((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - else if (RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK) - { - while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_PLLCLK) - { - if ((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - else if (RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLRCLK) - { - while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_PLLRCLK) - { - if ((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - else - { - while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSI) - { - if ((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - - /* Decreasing the number of wait states because of lower CPU frequency */ - if (FLatency < (FLASH->ACR & FLASH_ACR_LATENCY)) - { - /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */ - __HAL_FLASH_SET_LATENCY(FLatency); - - /* Check that the new number of wait states is taken into account to access the Flash - memory by reading the FLASH_ACR register */ - if ((FLASH->ACR & FLASH_ACR_LATENCY) != FLatency) - { - return HAL_ERROR; - } - } - - /*-------------------------- PCLK1 Configuration ---------------------------*/ - if (((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1) - { - assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB1CLKDivider)); - MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE1, RCC_ClkInitStruct->APB1CLKDivider); - } - - /*-------------------------- PCLK2 Configuration ---------------------------*/ - if (((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2) - { - assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB2CLKDivider)); - MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE2, ((RCC_ClkInitStruct->APB2CLKDivider) << 3U)); - } - - /* Update the SystemCoreClock global variable */ - SystemCoreClock = HAL_RCC_GetSysClockFreq() >> APBAHBPrescTable[(RCC->CFGR & RCC_CFGR_HPRE) >> POSITION_VAL(RCC_CFGR_HPRE)]; - /* Configure the source of time base considering new system clocks settings*/ - HAL_InitTick (TICK_INT_PRIORITY); - return HAL_OK; -} - -/** - * @} - */ - -/** @defgroup RCC_Exported_Functions_Group2 Peripheral Control functions - * @brief RCC clocks control functions - * -@verbatim - =============================================================================== - ##### Peripheral Control functions ##### - =============================================================================== - [..] - This subsection provides a set of functions allowing to control the RCC Clocks - frequencies. - -@endverbatim - * @{ - */ - -/** - * @brief Selects the clock source to output on MCO1 pin(PA8) or on MCO2 pin(PC9). - * @note PA8/PC9 should be configured in alternate function mode. - * @param RCC_MCOx: specifies the output direction for the clock source. - * This parameter can be one of the following values: - * @arg RCC_MCO1: Clock source to output on MCO1 pin(PA8). - * @arg RCC_MCO2: Clock source to output on MCO2 pin(PC9). - * @param RCC_MCOSource: specifies the clock source to output. - * This parameter can be one of the following values: - * @arg RCC_MCO1SOURCE_HSI: HSI clock selected as MCO1 source - * @arg RCC_MCO1SOURCE_LSE: LSE clock selected as MCO1 source - * @arg RCC_MCO1SOURCE_HSE: HSE clock selected as MCO1 source - * @arg RCC_MCO1SOURCE_PLLCLK: main PLL clock selected as MCO1 source - * @arg RCC_MCO2SOURCE_SYSCLK: System clock (SYSCLK) selected as MCO2 source - * @arg RCC_MCO2SOURCE_PLLI2SCLK: PLLI2S clock selected as MCO2 source, available for all STM32F4 devices except STM32F410xx - * @arg RCC_MCO2SOURCE_I2SCLK: I2SCLK clock selected as MCO2 source, available only for STM32F410Rx devices - * @arg RCC_MCO2SOURCE_HSE: HSE clock selected as MCO2 source - * @arg RCC_MCO2SOURCE_PLLCLK: main PLL clock selected as MCO2 source - * @param RCC_MCODiv: specifies the MCOx prescaler. - * This parameter can be one of the following values: - * @arg RCC_MCODIV_1: no division applied to MCOx clock - * @arg RCC_MCODIV_2: division by 2 applied to MCOx clock - * @arg RCC_MCODIV_3: division by 3 applied to MCOx clock - * @arg RCC_MCODIV_4: division by 4 applied to MCOx clock - * @arg RCC_MCODIV_5: division by 5 applied to MCOx clock - * @note For STM32F410Rx devices to output I2SCLK clock on MCO2 you should have - * at last one of the SPI clocks enabled (SPI1, SPI2 or SPI5). - * @retval None - */ -void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv) -{ - GPIO_InitTypeDef GPIO_InitStruct; - /* Check the parameters */ - assert_param(IS_RCC_MCO(RCC_MCOx)); - assert_param(IS_RCC_MCODIV(RCC_MCODiv)); - - /* RCC_MCO1 */ - if (RCC_MCOx == RCC_MCO1) - { - assert_param(IS_RCC_MCO1SOURCE(RCC_MCOSource)); - /* MCO1 Clock Enable */ - __MCO1_CLK_ENABLE(); - /* Configure the MCO1 pin in alternate function mode */ - GPIO_InitStruct.Pin = MCO1_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Alternate = GPIO_AF0_MCO; - HAL_GPIO_Init(MCO1_GPIO_PORT, &GPIO_InitStruct); - /* Mask MCO1 and MCO1PRE[2:0] bits then Select MCO1 clock source and prescaler */ - MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO1 | RCC_CFGR_MCO1PRE), (RCC_MCOSource | RCC_MCODiv)); - /* This RCC MCO1 enable feature is available only on STM32F410xx devices */ -#if defined(RCC_CFGR_MCO1EN) - __HAL_RCC_MCO1_ENABLE(); -#endif /* RCC_CFGR_MCO1EN */ - } - -#if defined(RCC_CFGR_MCO2) - else - { - assert_param(IS_RCC_MCO2SOURCE(RCC_MCOSource)); - /* MCO2 Clock Enable */ - __MCO2_CLK_ENABLE(); - /* Configure the MCO2 pin in alternate function mode */ - GPIO_InitStruct.Pin = MCO2_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Alternate = GPIO_AF0_MCO; - HAL_GPIO_Init(MCO2_GPIO_PORT, &GPIO_InitStruct); - /* Mask MCO2 and MCO2PRE[2:0] bits then Select MCO2 clock source and prescaler */ - MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO2 | RCC_CFGR_MCO2PRE), (RCC_MCOSource | (RCC_MCODiv << 3U))); - /* This RCC MCO2 enable feature is available only on STM32F410Rx devices */ -#if defined(RCC_CFGR_MCO2EN) - __HAL_RCC_MCO2_ENABLE(); -#endif /* RCC_CFGR_MCO2EN */ - } - -#endif /* RCC_CFGR_MCO2 */ -} - -/** - * @brief Enables the Clock Security System. - * @note If a failure is detected on the HSE oscillator clock, this oscillator - * is automatically disabled and an interrupt is generated to inform the - * software about the failure (Clock Security System Interrupt, CSSI), - * allowing the MCU to perform rescue operations. The CSSI is linked to - * the Cortex-M4 NMI (Non-Maskable Interrupt) exception vector. - * @retval None - */ -void HAL_RCC_EnableCSS(void) -{ - *(__IO uint32_t*) RCC_CR_CSSON_BB = (uint32_t)ENABLE; -} - -/** - * @brief Disables the Clock Security System. - * @retval None - */ -void HAL_RCC_DisableCSS(void) -{ - *(__IO uint32_t*) RCC_CR_CSSON_BB = (uint32_t)DISABLE; -} - -/** - * @brief Returns the SYSCLK frequency - * - * @note The system frequency computed by this function is not the real - * frequency in the chip. It is calculated based on the predefined - * constant and the selected clock source: - * @note If SYSCLK source is HSI, function returns values based on HSI_VALUE(*) - * @note If SYSCLK source is HSE, function returns values based on HSE_VALUE(**) - * @note If SYSCLK source is PLL, function returns values based on HSE_VALUE(**) - * or HSI_VALUE(*) multiplied/divided by the PLL factors. - * @note (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value - * 16 MHz) but the real value may vary depending on the variations - * in voltage and temperature. - * @note (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value - * 25 MHz), user has to ensure that HSE_VALUE is same as the real - * frequency of the crystal used. Otherwise, this function may - * have wrong result. - * - * @note The result of this function could be not correct when using fractional - * value for HSE crystal. - * - * @note This function can be used by the user application to compute the - * baudrate for the communication peripherals or configure other parameters. - * - * @note Each time SYSCLK changes, this function must be called to update the - * right SYSCLK value. Otherwise, any configuration based on this function will be incorrect. - * - * - * @retval SYSCLK frequency - */ -__weak uint32_t HAL_RCC_GetSysClockFreq(void) -{ - uint32_t pllm = 0U, pllvco = 0U, pllp = 0U; - uint32_t sysclockfreq = 0U; - - /* Get SYSCLK source -------------------------------------------------------*/ - switch (RCC->CFGR & RCC_CFGR_SWS) - { - case RCC_CFGR_SWS_HSI: /* HSI used as system clock source */ - { - sysclockfreq = HSI_VALUE; - break; - } - - case RCC_CFGR_SWS_HSE: /* HSE used as system clock source */ - { - sysclockfreq = HSE_VALUE; - break; - } - - case RCC_CFGR_SWS_PLL: /* PLL used as system clock source */ - { - /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLLM) * PLLN - SYSCLK = PLL_VCO / PLLP */ - pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM; - - if (__HAL_RCC_GET_PLL_OSCSOURCE() != RCC_PLLSOURCE_HSI) - { - /* HSE used as PLL clock source */ - pllvco = ((HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> POSITION_VAL(RCC_PLLCFGR_PLLN))); - } - else - { - /* HSI used as PLL clock source */ - pllvco = ((HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> POSITION_VAL(RCC_PLLCFGR_PLLN))); - } - - pllp = ((((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >> POSITION_VAL(RCC_PLLCFGR_PLLP)) + 1U) * 2U); - sysclockfreq = pllvco / pllp; - break; - } - - default: - { - sysclockfreq = HSI_VALUE; - break; - } - } - - return sysclockfreq; -} - -/** - * @brief Returns the HCLK frequency - * @note Each time HCLK changes, this function must be called to update the - * right HCLK value. Otherwise, any configuration based on this function will be incorrect. - * - * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency - * and updated within this function - * @retval HCLK frequency - */ -uint32_t HAL_RCC_GetHCLKFreq(void) -{ - return SystemCoreClock; -} - -/** - * @brief Returns the PCLK1 frequency - * @note Each time PCLK1 changes, this function must be called to update the - * right PCLK1 value. Otherwise, any configuration based on this function will be incorrect. - * @retval PCLK1 frequency - */ -uint32_t HAL_RCC_GetPCLK1Freq(void) -{ - /* Get HCLK source and Compute PCLK1 frequency ---------------------------*/ - return (HAL_RCC_GetHCLKFreq() >> APBAHBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE1) >> POSITION_VAL(RCC_CFGR_PPRE1)]); -} - -/** - * @brief Returns the PCLK2 frequency - * @note Each time PCLK2 changes, this function must be called to update the - * right PCLK2 value. Otherwise, any configuration based on this function will be incorrect. - * @retval PCLK2 frequency - */ -uint32_t HAL_RCC_GetPCLK2Freq(void) -{ - /* Get HCLK source and Compute PCLK2 frequency ---------------------------*/ - return (HAL_RCC_GetHCLKFreq() >> APBAHBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE2) >> POSITION_VAL(RCC_CFGR_PPRE2)]); -} - -/** - * @brief Configures the RCC_OscInitStruct according to the internal - * RCC configuration registers. - * @param RCC_OscInitStruct: pointer to an RCC_OscInitTypeDef structure that - * will be configured. - * @retval None - */ -__weak void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef* RCC_OscInitStruct) -{ - /* Set all possible values for the Oscillator type parameter ---------------*/ - RCC_OscInitStruct->OscillatorType = RCC_OSCILLATORTYPE_HSE | RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_LSE | RCC_OSCILLATORTYPE_LSI; - - /* Get the HSE configuration -----------------------------------------------*/ - if ((RCC->CR & RCC_CR_HSEBYP) == RCC_CR_HSEBYP) - { - RCC_OscInitStruct->HSEState = RCC_HSE_BYPASS; - } - else if ((RCC->CR & RCC_CR_HSEON) == RCC_CR_HSEON) - { - RCC_OscInitStruct->HSEState = RCC_HSE_ON; - } - else - { - RCC_OscInitStruct->HSEState = RCC_HSE_OFF; - } - - /* Get the HSI configuration -----------------------------------------------*/ - if ((RCC->CR & RCC_CR_HSION) == RCC_CR_HSION) - { - RCC_OscInitStruct->HSIState = RCC_HSI_ON; - } - else - { - RCC_OscInitStruct->HSIState = RCC_HSI_OFF; - } - - RCC_OscInitStruct->HSICalibrationValue = (uint32_t)((RCC->CR & RCC_CR_HSITRIM) >> POSITION_VAL(RCC_CR_HSITRIM)); - - /* Get the LSE configuration -----------------------------------------------*/ - if ((RCC->BDCR & RCC_BDCR_LSEBYP) == RCC_BDCR_LSEBYP) - { - RCC_OscInitStruct->LSEState = RCC_LSE_BYPASS; - } - else if ((RCC->BDCR & RCC_BDCR_LSEON) == RCC_BDCR_LSEON) - { - RCC_OscInitStruct->LSEState = RCC_LSE_ON; - } - else - { - RCC_OscInitStruct->LSEState = RCC_LSE_OFF; - } - - /* Get the LSI configuration -----------------------------------------------*/ - if ((RCC->CSR & RCC_CSR_LSION) == RCC_CSR_LSION) - { - RCC_OscInitStruct->LSIState = RCC_LSI_ON; - } - else - { - RCC_OscInitStruct->LSIState = RCC_LSI_OFF; - } - - /* Get the PLL configuration -----------------------------------------------*/ - if ((RCC->CR & RCC_CR_PLLON) == RCC_CR_PLLON) - { - RCC_OscInitStruct->PLL.PLLState = RCC_PLL_ON; - } - else - { - RCC_OscInitStruct->PLL.PLLState = RCC_PLL_OFF; - } - - RCC_OscInitStruct->PLL.PLLSource = (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC); - RCC_OscInitStruct->PLL.PLLM = (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM); - RCC_OscInitStruct->PLL.PLLN = (uint32_t)((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> POSITION_VAL(RCC_PLLCFGR_PLLN)); - RCC_OscInitStruct->PLL.PLLP = (uint32_t)((((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) + RCC_PLLCFGR_PLLP_0) << 1U) >> POSITION_VAL(RCC_PLLCFGR_PLLP)); - RCC_OscInitStruct->PLL.PLLQ = (uint32_t)((RCC->PLLCFGR & RCC_PLLCFGR_PLLQ) >> POSITION_VAL(RCC_PLLCFGR_PLLQ)); -} - -/** - * @brief Configures the RCC_ClkInitStruct according to the internal - * RCC configuration registers. - * @param RCC_ClkInitStruct: pointer to an RCC_ClkInitTypeDef structure that - * will be configured. - * @param pFLatency: Pointer on the Flash Latency. - * @retval None - */ -void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef* RCC_ClkInitStruct, uint32_t* pFLatency) -{ - /* Set all possible values for the Clock type parameter --------------------*/ - RCC_ClkInitStruct->ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2; - /* Get the SYSCLK configuration --------------------------------------------*/ - RCC_ClkInitStruct->SYSCLKSource = (uint32_t)(RCC->CFGR & RCC_CFGR_SW); - /* Get the HCLK configuration ----------------------------------------------*/ - RCC_ClkInitStruct->AHBCLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_HPRE); - /* Get the APB1 configuration ----------------------------------------------*/ - RCC_ClkInitStruct->APB1CLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_PPRE1); - /* Get the APB2 configuration ----------------------------------------------*/ - RCC_ClkInitStruct->APB2CLKDivider = (uint32_t)((RCC->CFGR & RCC_CFGR_PPRE2) >> 3U); - /* Get the Flash Wait State (Latency) configuration ------------------------*/ - *pFLatency = (uint32_t)(FLASH->ACR & FLASH_ACR_LATENCY); -} - -/** - * @brief This function handles the RCC CSS interrupt request. - * @note This API should be called under the NMI_Handler(). - * @retval None - */ -void HAL_RCC_NMI_IRQHandler(void) -{ - /* Check RCC CSSF flag */ - if (__HAL_RCC_GET_IT(RCC_IT_CSS)) - { - /* RCC Clock Security System interrupt user callback */ - HAL_RCC_CSSCallback(); - /* Clear RCC CSS pending bit */ - __HAL_RCC_CLEAR_IT(RCC_IT_CSS); - } -} - -/** - * @brief RCC Clock Security System interrupt callback - * @retval None - */ -__weak void HAL_RCC_CSSCallback(void) -{ - /* NOTE : This function Should not be modified, when the callback is needed, - the HAL_RCC_CSSCallback could be implemented in the user file - */ -} - -/** - * @} - */ - -/** - * @} - */ - -#endif /* HAL_RCC_MODULE_ENABLED */ -/** - * @} - */ - -/** - * @} - */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc_ex.c b/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc_ex.c deleted file mode 100644 index 99946baf..00000000 --- a/EpsilonLights/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc_ex.c +++ /dev/null @@ -1,2586 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_rcc_ex.c - * @author MCD Application Team - * @version V1.5.0 - * @date 06-May-2016 - * @brief Extension RCC HAL module driver. - * This file provides firmware functions to manage the following - * functionalities RCC extension peripheral: - * + Extended Peripheral Control functions - * - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f4xx_hal.h" - -/** @addtogroup STM32F4xx_HAL_Driver - * @{ - */ - -/** @defgroup RCCEx RCCEx - * @brief RCCEx HAL module driver - * @{ - */ - -#ifdef HAL_RCC_MODULE_ENABLED - -/* Private typedef -----------------------------------------------------------*/ -/* Private define ------------------------------------------------------------*/ -/** @addtogroup RCCEx_Private_Constants - * @{ - */ -/** - * @} - */ -/* Private macro -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/* Private function prototypes -----------------------------------------------*/ -/* Private functions ---------------------------------------------------------*/ -/** @defgroup RCCEx_Exported_Functions RCCEx Exported Functions - * @{ - */ - -/** @defgroup RCCEx_Exported_Functions_Group1 Extended Peripheral Control functions - * @brief Extended Peripheral Control functions - * -@verbatim - =============================================================================== - ##### Extended Peripheral Control functions ##### - =============================================================================== - [..] - This subsection provides a set of functions allowing to control the RCC Clocks - frequencies. - [..] - (@) Important note: Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to - select the RTC clock source; in this case the Backup domain will be reset in - order to modify the RTC Clock source, as consequence RTC registers (including - the backup registers) and RCC_BDCR register are set to their reset values. - -@endverbatim - * @{ - */ -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \ - defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \ - defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ - defined(STM32F412Rx) || defined(STM32F412Cx) -/** - * @brief Resets the RCC clock configuration to the default reset state. - * @note The default reset state of the clock configuration is given below: - * - HSI ON and used as system clock source - * - HSE, PLL and PLLI2S OFF - * - AHB, APB1 and APB2 prescaler set to 1. - * - CSS, MCO1 and MCO2 OFF - * - All interrupts disabled - * @note This function doesn't modify the configuration of the - * - Peripheral clocks - * - LSI, LSE and RTC clocks - * @retval None - */ -void HAL_RCC_DeInit(void) -{ - /* Set HSION bit */ - SET_BIT(RCC->CR, RCC_CR_HSION | RCC_CR_HSITRIM_4); - /* Reset CFGR register */ - CLEAR_REG(RCC->CFGR); - /* Reset HSEON, CSSON, PLLON, PLLI2S */ - CLEAR_BIT(RCC->CR, RCC_CR_HSEON | RCC_CR_CSSON | RCC_CR_PLLON | RCC_CR_PLLI2SON); - /* Reset PLLCFGR register */ - CLEAR_REG(RCC->PLLCFGR); - SET_BIT(RCC->PLLCFGR, RCC_PLLCFGR_PLLM_4 | RCC_PLLCFGR_PLLN_6 | RCC_PLLCFGR_PLLN_7 | RCC_PLLCFGR_PLLQ_2); - /* Reset PLLI2SCFGR register */ - CLEAR_REG(RCC->PLLI2SCFGR); - SET_BIT(RCC->PLLI2SCFGR, RCC_PLLI2SCFGR_PLLI2SN_6 | RCC_PLLI2SCFGR_PLLI2SN_7 | RCC_PLLI2SCFGR_PLLI2SR_1); - /* Reset HSEBYP bit */ - CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); - /* Disable all interrupts */ - CLEAR_REG(RCC->CIR); - /* Update the SystemCoreClock global variable */ - SystemCoreClock = HSI_VALUE; -} -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || - STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || - STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -/** - * @brief Resets the RCC clock configuration to the default reset state. - * @note The default reset state of the clock configuration is given below: - * - HSI ON and used as system clock source - * - HSE and PLL OFF - * - AHB, APB1 and APB2 prescaler set to 1. - * - CSS, MCO1 and MCO2 OFF - * - All interrupts disabled - * @note This function doesn't modify the configuration of the - * - Peripheral clocks - * - LSI, LSE and RTC clocks - * @retval None - */ -void HAL_RCC_DeInit(void) -{ - /* Set HSION bit */ - SET_BIT(RCC->CR, RCC_CR_HSION | RCC_CR_HSITRIM_4); - /* Reset CFGR register */ - CLEAR_REG(RCC->CFGR); - /* Reset HSEON, CSSON, PLLON */ - CLEAR_BIT(RCC->CR, RCC_CR_HSEON | RCC_CR_CSSON | RCC_CR_PLLON); - /* Reset PLLCFGR register */ - CLEAR_REG(RCC->PLLCFGR); - SET_BIT(RCC->PLLCFGR, RCC_PLLCFGR_PLLR_1 | RCC_PLLCFGR_PLLM_4 | RCC_PLLCFGR_PLLN_6 | RCC_PLLCFGR_PLLN_7 | RCC_PLLCFGR_PLLQ_2); - /* Reset HSEBYP bit */ - CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); - /* Disable all interrupts */ - CLEAR_REG(RCC->CIR); - /* Update the SystemCoreClock global variable */ - SystemCoreClock = HSI_VALUE; -} -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -#if defined(STM32F446xx) -/** - * @brief Initializes the RCC extended peripherals clocks according to the specified - * parameters in the RCC_PeriphCLKInitTypeDef. - * @param PeriphClkInit: pointer to an RCC_PeriphCLKInitTypeDef structure that - * contains the configuration information for the Extended Peripherals - * clocks(I2S, SAI, LTDC RTC and TIM). - * - * @note Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select - * the RTC clock source; in this case the Backup domain will be reset in - * order to modify the RTC Clock source, as consequence RTC registers (including - * the backup registers) and RCC_BDCR register are set to their reset values. - * - * @retval HAL status - */ -HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit) -{ - uint32_t tickstart = 0U; - uint32_t tmpreg1 = 0U; - uint32_t plli2sp = 0U; - uint32_t plli2sq = 0U; - uint32_t plli2sr = 0U; - uint32_t pllsaip = 0U; - uint32_t pllsaiq = 0U; - uint32_t plli2sused = 0U; - uint32_t pllsaiused = 0U; - /* Check the peripheral clock selection parameters */ - assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection)); - - /*------------------------ I2S APB1 configuration --------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB1) == (RCC_PERIPHCLK_I2S_APB1)) - { - /* Check the parameters */ - assert_param(IS_RCC_I2SAPB1CLKSOURCE(PeriphClkInit->I2sApb1ClockSelection)); - /* Configure I2S Clock source */ - __HAL_RCC_I2S_APB1_CONFIG(PeriphClkInit->I2sApb1ClockSelection); - - /* Enable the PLLI2S when it's used as clock source for I2S */ - if (PeriphClkInit->I2sApb1ClockSelection == RCC_I2SAPB1CLKSOURCE_PLLI2S) - { - plli2sused = 1U; - } - } - - /*--------------------------------------------------------------------------*/ - - /*---------------------------- I2S APB2 configuration ----------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB2) == (RCC_PERIPHCLK_I2S_APB2)) - { - /* Check the parameters */ - assert_param(IS_RCC_I2SAPB2CLKSOURCE(PeriphClkInit->I2sApb2ClockSelection)); - /* Configure I2S Clock source */ - __HAL_RCC_I2S_APB2_CONFIG(PeriphClkInit->I2sApb2ClockSelection); - - /* Enable the PLLI2S when it's used as clock source for I2S */ - if (PeriphClkInit->I2sApb2ClockSelection == RCC_I2SAPB2CLKSOURCE_PLLI2S) - { - plli2sused = 1U; - } - } - - /*--------------------------------------------------------------------------*/ - - /*--------------------------- SAI1 configuration ---------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI1) == (RCC_PERIPHCLK_SAI1)) - { - /* Check the parameters */ - assert_param(IS_RCC_SAI1CLKSOURCE(PeriphClkInit->Sai1ClockSelection)); - /* Configure SAI1 Clock source */ - __HAL_RCC_SAI1_CONFIG(PeriphClkInit->Sai1ClockSelection); - - /* Enable the PLLI2S when it's used as clock source for SAI */ - if (PeriphClkInit->Sai1ClockSelection == RCC_SAI1CLKSOURCE_PLLI2S) - { - plli2sused = 1U; - } - - /* Enable the PLLSAI when it's used as clock source for SAI */ - if (PeriphClkInit->Sai1ClockSelection == RCC_SAI1CLKSOURCE_PLLSAI) - { - pllsaiused = 1U; - } - } - - /*--------------------------------------------------------------------------*/ - - /*-------------------------- SAI2 configuration ----------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI2) == (RCC_PERIPHCLK_SAI2)) - { - /* Check the parameters */ - assert_param(IS_RCC_SAI2CLKSOURCE(PeriphClkInit->Sai2ClockSelection)); - /* Configure SAI2 Clock source */ - __HAL_RCC_SAI2_CONFIG(PeriphClkInit->Sai2ClockSelection); - - /* Enable the PLLI2S when it's used as clock source for SAI */ - if (PeriphClkInit->Sai2ClockSelection == RCC_SAI2CLKSOURCE_PLLI2S) - { - plli2sused = 1U; - } - - /* Enable the PLLSAI when it's used as clock source for SAI */ - if (PeriphClkInit->Sai2ClockSelection == RCC_SAI2CLKSOURCE_PLLSAI) - { - pllsaiused = 1U; - } - } - - /*--------------------------------------------------------------------------*/ - - /*----------------------------- RTC configuration --------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == (RCC_PERIPHCLK_RTC)) - { - /* Check for RTC Parameters used to output RTCCLK */ - assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection)); - /* Enable Power Clock*/ - __HAL_RCC_PWR_CLK_ENABLE(); - /* Enable write access to Backup domain */ - PWR->CR |= PWR_CR_DBP; - /* Get tick */ - tickstart = HAL_GetTick(); - - while ((PWR->CR & PWR_CR_DBP) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Reset the Backup domain only if the RTC Clock source selection is modified from reset value */ - tmpreg1 = (RCC->BDCR & RCC_BDCR_RTCSEL); - - if ((tmpreg1 != 0x00000000U) && ((tmpreg1) != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL))) - { - /* Store the content of BDCR register before the reset of Backup Domain */ - tmpreg1 = (RCC->BDCR & ~(RCC_BDCR_RTCSEL)); - /* RTC Clock selection can be changed only if the Backup Domain is reset */ - __HAL_RCC_BACKUPRESET_FORCE(); - __HAL_RCC_BACKUPRESET_RELEASE(); - /* Restore the Content of BDCR register */ - RCC->BDCR = tmpreg1; - - /* Wait for LSE reactivation if LSE was enable prior to Backup Domain reset */ - if (HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSEON)) - { - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till LSE is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - - __HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*---------------------------- TIM configuration ---------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_TIM) == (RCC_PERIPHCLK_TIM)) - { - /* Configure Timer Prescaler */ - __HAL_RCC_TIMCLKPRESCALER(PeriphClkInit->TIMPresSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*---------------------------- FMPI2C1 Configuration -----------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_FMPI2C1) == RCC_PERIPHCLK_FMPI2C1) - { - /* Check the parameters */ - assert_param(IS_RCC_FMPI2C1CLKSOURCE(PeriphClkInit->Fmpi2c1ClockSelection)); - /* Configure the FMPI2C1 clock source */ - __HAL_RCC_FMPI2C1_CONFIG(PeriphClkInit->Fmpi2c1ClockSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*------------------------------ CEC Configuration -------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CEC) == RCC_PERIPHCLK_CEC) - { - /* Check the parameters */ - assert_param(IS_RCC_CECCLKSOURCE(PeriphClkInit->CecClockSelection)); - /* Configure the CEC clock source */ - __HAL_RCC_CEC_CONFIG(PeriphClkInit->CecClockSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*----------------------------- CLK48 Configuration ------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == RCC_PERIPHCLK_CLK48) - { - /* Check the parameters */ - assert_param(IS_RCC_CLK48CLKSOURCE(PeriphClkInit->Clk48ClockSelection)); - /* Configure the CLK48 clock source */ - __HAL_RCC_CLK48_CONFIG(PeriphClkInit->Clk48ClockSelection); - - /* Enable the PLLSAI when it's used as clock source for CLK48 */ - if (PeriphClkInit->Clk48ClockSelection == RCC_CLK48CLKSOURCE_PLLSAIP) - { - pllsaiused = 1U; - } - } - - /*--------------------------------------------------------------------------*/ - - /*----------------------------- SDIO Configuration -------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SDIO) == RCC_PERIPHCLK_SDIO) - { - /* Check the parameters */ - assert_param(IS_RCC_SDIOCLKSOURCE(PeriphClkInit->SdioClockSelection)); - /* Configure the SDIO clock source */ - __HAL_RCC_SDIO_CONFIG(PeriphClkInit->SdioClockSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*------------------------------ SPDIFRX Configuration ---------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SPDIFRX) == RCC_PERIPHCLK_SPDIFRX) - { - /* Check the parameters */ - assert_param(IS_RCC_SPDIFRXCLKSOURCE(PeriphClkInit->SpdifClockSelection)); - /* Configure the SPDIFRX clock source */ - __HAL_RCC_SPDIFRX_CONFIG(PeriphClkInit->SpdifClockSelection); - - /* Enable the PLLI2S when it's used as clock source for SPDIFRX */ - if (PeriphClkInit->SpdifClockSelection == RCC_SPDIFRXCLKSOURCE_PLLI2SP) - { - plli2sused = 1U; - } - } - - /*--------------------------------------------------------------------------*/ - - /*---------------------------- PLLI2S Configuration ------------------------*/ - /* PLLI2S is configured when a peripheral will use it as source clock : SAI1, SAI2, I2S on APB1, - I2S on APB2 or SPDIFRX */ - if ((plli2sused == 1U) || (PeriphClkInit->PeriphClockSelection == RCC_PERIPHCLK_PLLI2S)) - { - /* Disable the PLLI2S */ - __HAL_RCC_PLLI2S_DISABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLI2S is disabled */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - - /* check for common PLLI2S Parameters */ - assert_param(IS_RCC_PLLI2SM_VALUE(PeriphClkInit->PLLI2S.PLLI2SM)); - assert_param(IS_RCC_PLLI2SN_VALUE(PeriphClkInit->PLLI2S.PLLI2SN)); - - /*------ In Case of PLLI2S is selected as source clock for I2S -----------*/ - if (((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB1) == RCC_PERIPHCLK_I2S_APB1) && (PeriphClkInit->I2sApb1ClockSelection == RCC_I2SAPB1CLKSOURCE_PLLI2S)) || - ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB2) == RCC_PERIPHCLK_I2S_APB2) && (PeriphClkInit->I2sApb2ClockSelection == RCC_I2SAPB2CLKSOURCE_PLLI2S))) - { - /* check for Parameters */ - assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); - /* Read PLLI2SP/PLLI2SQ value from PLLI2SCFGR register (this value is not needed for I2S configuration) */ - plli2sp = ((((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SP) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SP)) + 1U) << 1U); - plli2sq = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SQ)); - /* Configure the PLLI2S division factors */ - /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLI2SM) */ - /* I2SCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SR */ - __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SM, PeriphClkInit->PLLI2S.PLLI2SN, plli2sp, plli2sq, PeriphClkInit->PLLI2S.PLLI2SR); - } - - /*------- In Case of PLLI2S is selected as source clock for SAI ----------*/ - if (((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI1) == RCC_PERIPHCLK_SAI1) && (PeriphClkInit->Sai1ClockSelection == RCC_SAI1CLKSOURCE_PLLI2S)) || - ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI2) == RCC_PERIPHCLK_SAI2) && (PeriphClkInit->Sai2ClockSelection == RCC_SAI2CLKSOURCE_PLLI2S))) - { - /* Check for PLLI2S Parameters */ - assert_param(IS_RCC_PLLI2SQ_VALUE(PeriphClkInit->PLLI2S.PLLI2SQ)); - /* Check for PLLI2S/DIVQ parameters */ - assert_param(IS_RCC_PLLI2S_DIVQ_VALUE(PeriphClkInit->PLLI2SDivQ)); - /* Read PLLI2SP/PLLI2SR value from PLLI2SCFGR register (this value is not needed for SAI configuration) */ - plli2sp = ((((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SP) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SP)) + 1U) << 1U); - plli2sr = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)); - /* Configure the PLLI2S division factors */ - /* PLLI2S_VCO Input = PLL_SOURCE/PLLI2SM */ - /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ - /* SAI_CLK(first level) = PLLI2S_VCO Output/PLLI2SQ */ - __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SM, PeriphClkInit->PLLI2S.PLLI2SN, plli2sp, PeriphClkInit->PLLI2S.PLLI2SQ, plli2sr); - /* SAI_CLK_x = SAI_CLK(first level)/PLLI2SDIVQ */ - __HAL_RCC_PLLI2S_PLLSAICLKDIVQ_CONFIG(PeriphClkInit->PLLI2SDivQ); - } - - /*------ In Case of PLLI2S is selected as source clock for SPDIFRX -------*/ - if ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SPDIFRX) == RCC_PERIPHCLK_SPDIFRX) && (PeriphClkInit->SpdifClockSelection == RCC_SPDIFRXCLKSOURCE_PLLI2SP)) - { - /* check for Parameters */ - assert_param(IS_RCC_PLLI2SP_VALUE(PeriphClkInit->PLLI2S.PLLI2SP)); - /* Read PLLI2SR value from PLLI2SCFGR register (this value is not need for SAI configuration) */ - plli2sq = ((((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SP) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SP)) + 1U) << 1U); - plli2sr = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)); - /* Configure the PLLI2S division factors */ - /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLI2SM) */ - /* SPDIFRXCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SP */ - __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SM, PeriphClkInit->PLLI2S.PLLI2SN, PeriphClkInit->PLLI2S.PLLI2SP, plli2sq, plli2sr); - } - - /*----------------- In Case of PLLI2S is just selected -----------------*/ - if ((PeriphClkInit->PeriphClockSelection & RCC_PERIPHCLK_PLLI2S) == RCC_PERIPHCLK_PLLI2S) - { - /* Check for Parameters */ - assert_param(IS_RCC_PLLI2SP_VALUE(PeriphClkInit->PLLI2S.PLLI2SP)); - assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); - assert_param(IS_RCC_PLLI2SQ_VALUE(PeriphClkInit->PLLI2S.PLLI2SQ)); - /* Configure the PLLI2S division factors */ - /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLI2SM) */ - __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SM, PeriphClkInit->PLLI2S.PLLI2SN, PeriphClkInit->PLLI2S.PLLI2SP, PeriphClkInit->PLLI2S.PLLI2SQ, PeriphClkInit->PLLI2S.PLLI2SR); - } - - /* Enable the PLLI2S */ - __HAL_RCC_PLLI2S_ENABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLI2S is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - } - - /*--------------------------------------------------------------------------*/ - - /*----------------------------- PLLSAI Configuration -----------------------*/ - /* PLLSAI is configured when a peripheral will use it as source clock : SAI1, SAI2, CLK48 or SDIO */ - if (pllsaiused == 1U) - { - /* Disable PLLSAI Clock */ - __HAL_RCC_PLLSAI_DISABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLSAI is disabled */ - while (__HAL_RCC_PLLSAI_GET_FLAG() != RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLSAI_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - - /* Check the PLLSAI division factors */ - assert_param(IS_RCC_PLLSAIM_VALUE(PeriphClkInit->PLLSAI.PLLSAIM)); - assert_param(IS_RCC_PLLSAIN_VALUE(PeriphClkInit->PLLSAI.PLLSAIN)); - - /*------ In Case of PLLSAI is selected as source clock for SAI -----------*/ - if (((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI1) == RCC_PERIPHCLK_SAI1) && (PeriphClkInit->Sai1ClockSelection == RCC_SAI1CLKSOURCE_PLLSAI)) || - ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI2) == RCC_PERIPHCLK_SAI2) && (PeriphClkInit->Sai2ClockSelection == RCC_SAI2CLKSOURCE_PLLSAI))) - { - /* check for PLLSAIQ Parameter */ - assert_param(IS_RCC_PLLSAIQ_VALUE(PeriphClkInit->PLLSAI.PLLSAIQ)); - /* check for PLLSAI/DIVQ Parameter */ - assert_param(IS_RCC_PLLSAI_DIVQ_VALUE(PeriphClkInit->PLLSAIDivQ)); - /* Read PLLSAIP value from PLLSAICFGR register (this value is not needed for SAI configuration) */ - pllsaip = ((((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIP) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIP)) + 1U) << 1U); - /* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ - /* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ - /* SAI_CLK(first level) = PLLSAI_VCO Output/PLLSAIQ */ - __HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIM, PeriphClkInit->PLLSAI.PLLSAIN, pllsaip, PeriphClkInit->PLLSAI.PLLSAIQ, 0U); - /* SAI_CLK_x = SAI_CLK(first level)/PLLSAIDIVQ */ - __HAL_RCC_PLLSAI_PLLSAICLKDIVQ_CONFIG(PeriphClkInit->PLLSAIDivQ); - } - - /*------ In Case of PLLSAI is selected as source clock for CLK48 ---------*/ - /* In Case of PLLI2S is selected as source clock for CLK48 */ - if ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == RCC_PERIPHCLK_CLK48) && (PeriphClkInit->Clk48ClockSelection == RCC_CLK48CLKSOURCE_PLLSAIP)) - { - /* check for Parameters */ - assert_param(IS_RCC_PLLSAIP_VALUE(PeriphClkInit->PLLSAI.PLLSAIP)); - /* Read PLLSAIQ value from PLLI2SCFGR register (this value is not need for SAI configuration) */ - pllsaiq = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ)); - /* Configure the PLLSAI division factors */ - /* PLLSAI_VCO = f(VCO clock) = f(PLLSAI clock input) * (PLLI2SN/PLLSAIM) */ - /* 48CLK = f(PLLSAI clock output) = f(VCO clock) / PLLSAIP */ - __HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIM, PeriphClkInit->PLLSAI.PLLSAIN, PeriphClkInit->PLLSAI.PLLSAIP, pllsaiq, 0U); - } - - /* Enable PLLSAI Clock */ - __HAL_RCC_PLLSAI_ENABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLSAI is ready */ - while (__HAL_RCC_PLLSAI_GET_FLAG() == RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLSAI_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - } - - return HAL_OK; -} - -/** - * @brief Get the RCC_PeriphCLKInitTypeDef according to the internal - * RCC configuration registers. - * @param PeriphClkInit: pointer to an RCC_PeriphCLKInitTypeDef structure that - * will be configured. - * @retval None - */ -void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit) -{ - uint32_t tempreg; - /* Set all possible values for the extended clock type parameter------------*/ - PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_I2S_APB1 | RCC_PERIPHCLK_I2S_APB2 | \ - RCC_PERIPHCLK_SAI1 | RCC_PERIPHCLK_SAI2 | \ - RCC_PERIPHCLK_TIM | RCC_PERIPHCLK_RTC | \ - RCC_PERIPHCLK_CEC | RCC_PERIPHCLK_FMPI2C1 | \ - RCC_PERIPHCLK_CLK48 | RCC_PERIPHCLK_SDIO | \ - RCC_PERIPHCLK_SPDIFRX; - /* Get the PLLI2S Clock configuration --------------------------------------*/ - PeriphClkInit->PLLI2S.PLLI2SM = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SM)); - PeriphClkInit->PLLI2S.PLLI2SN = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)); - PeriphClkInit->PLLI2S.PLLI2SP = (uint32_t)((((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SP) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SP)) + 1U) << 1U); - PeriphClkInit->PLLI2S.PLLI2SQ = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SQ)); - PeriphClkInit->PLLI2S.PLLI2SR = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)); - /* Get the PLLSAI Clock configuration --------------------------------------*/ - PeriphClkInit->PLLSAI.PLLSAIM = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIM) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIM)); - PeriphClkInit->PLLSAI.PLLSAIN = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIN) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIN)); - PeriphClkInit->PLLSAI.PLLSAIP = (uint32_t)((((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIP) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIP)) + 1U) << 1U); - PeriphClkInit->PLLSAI.PLLSAIQ = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ)); - /* Get the PLLSAI/PLLI2S division factors ----------------------------------*/ - PeriphClkInit->PLLI2SDivQ = (uint32_t)((RCC->DCKCFGR & RCC_DCKCFGR_PLLI2SDIVQ) >> POSITION_VAL(RCC_DCKCFGR_PLLI2SDIVQ)); - PeriphClkInit->PLLSAIDivQ = (uint32_t)((RCC->DCKCFGR & RCC_DCKCFGR_PLLSAIDIVQ) >> POSITION_VAL(RCC_DCKCFGR_PLLSAIDIVQ)); - /* Get the SAI1 clock configuration ----------------------------------------*/ - PeriphClkInit->Sai1ClockSelection = __HAL_RCC_GET_SAI1_SOURCE(); - /* Get the SAI2 clock configuration ----------------------------------------*/ - PeriphClkInit->Sai2ClockSelection = __HAL_RCC_GET_SAI2_SOURCE(); - /* Get the I2S APB1 clock configuration ------------------------------------*/ - PeriphClkInit->I2sApb1ClockSelection = __HAL_RCC_GET_I2S_APB1_SOURCE(); - /* Get the I2S APB2 clock configuration ------------------------------------*/ - PeriphClkInit->I2sApb2ClockSelection = __HAL_RCC_GET_I2S_APB2_SOURCE(); - /* Get the RTC Clock configuration -----------------------------------------*/ - tempreg = (RCC->CFGR & RCC_CFGR_RTCPRE); - PeriphClkInit->RTCClockSelection = (uint32_t)((tempreg) | (RCC->BDCR & RCC_BDCR_RTCSEL)); - /* Get the CEC clock configuration -----------------------------------------*/ - PeriphClkInit->CecClockSelection = __HAL_RCC_GET_CEC_SOURCE(); - /* Get the FMPI2C1 clock configuration -------------------------------------*/ - PeriphClkInit->Fmpi2c1ClockSelection = __HAL_RCC_GET_FMPI2C1_SOURCE(); - /* Get the CLK48 clock configuration ----------------------------------------*/ - PeriphClkInit->Clk48ClockSelection = __HAL_RCC_GET_CLK48_SOURCE(); - /* Get the SDIO clock configuration ----------------------------------------*/ - PeriphClkInit->SdioClockSelection = __HAL_RCC_GET_SDIO_SOURCE(); - /* Get the SPDIFRX clock configuration -------------------------------------*/ - PeriphClkInit->SpdifClockSelection = __HAL_RCC_GET_SPDIFRX_SOURCE(); - - /* Get the TIM Prescaler configuration -------------------------------------*/ - if ((RCC->DCKCFGR & RCC_DCKCFGR_TIMPRE) == RESET) - { - PeriphClkInit->TIMPresSelection = RCC_TIMPRES_DESACTIVATED; - } - else - { - PeriphClkInit->TIMPresSelection = RCC_TIMPRES_ACTIVATED; - } -} - -/** - * @brief Return the peripheral clock frequency for a given peripheral(SAI..) - * @note Return 0 if peripheral clock identifier not managed by this API - * @param PeriphClk: Peripheral clock identifier - * This parameter can be one of the following values: - * @arg RCC_PERIPHCLK_SAI1: SAI1 peripheral clock - * @arg RCC_PERIPHCLK_SAI2: SAI2 peripheral clock - * @retval Frequency in KHz - */ -uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk) -{ - uint32_t tmpreg1 = 0U; - /* This variable used to store the SAI clock frequency (value in Hz) */ - uint32_t frequency = 0U; - /* This variable used to store the VCO Input (value in Hz) */ - uint32_t vcoinput = 0U; - /* This variable used to store the SAI clock source */ - uint32_t saiclocksource = 0U; - - if ((PeriphClk == RCC_PERIPHCLK_SAI1) || (PeriphClk == RCC_PERIPHCLK_SAI2)) - { - saiclocksource = RCC->DCKCFGR; - saiclocksource &= (RCC_DCKCFGR_SAI1SRC | RCC_DCKCFGR_SAI2SRC); - - switch (saiclocksource) - { - case 0U: /* PLLSAI is the clock source for SAI*/ - { - /* Configure the PLLSAI division factor */ - /* PLLSAI_VCO Input = PLL_SOURCE/PLLSAIM */ - if ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSI) - { - /* In Case the PLL Source is HSI (Internal Clock) */ - vcoinput = (HSI_VALUE / (uint32_t)(RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIM)); - } - else - { - /* In Case the PLL Source is HSE (External Clock) */ - vcoinput = ((HSE_VALUE / (uint32_t)(RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIM))); - } - - /* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ - /* SAI_CLK(first level) = PLLSAI_VCO Output/PLLSAIQ */ - tmpreg1 = (RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> 24U; - frequency = (vcoinput * ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIN) >> 6U)) / (tmpreg1); - /* SAI_CLK_x = SAI_CLK(first level)/PLLSAIDIVQ */ - tmpreg1 = (((RCC->DCKCFGR & RCC_DCKCFGR_PLLSAIDIVQ) >> 8U) + 1U); - frequency = frequency / (tmpreg1); - break; - } - - case RCC_DCKCFGR_SAI1SRC_0: /* PLLI2S is the clock source for SAI*/ - case RCC_DCKCFGR_SAI2SRC_0: /* PLLI2S is the clock source for SAI*/ - { - /* Configure the PLLI2S division factor */ - /* PLLI2S_VCO Input = PLL_SOURCE/PLLI2SM */ - if ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSI) - { - /* In Case the PLL Source is HSI (Internal Clock) */ - vcoinput = (HSI_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM)); - } - else - { - /* In Case the PLL Source is HSE (External Clock) */ - vcoinput = ((HSE_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM))); - } - - /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ - /* SAI_CLK(first level) = PLLI2S_VCO Output/PLLI2SQ */ - tmpreg1 = (RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> 24U; - frequency = (vcoinput * ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> 6U)) / (tmpreg1); - /* SAI_CLK_x = SAI_CLK(first level)/PLLI2SDIVQ */ - tmpreg1 = ((RCC->DCKCFGR & RCC_DCKCFGR_PLLI2SDIVQ) + 1U); - frequency = frequency / (tmpreg1); - break; - } - - case RCC_DCKCFGR_SAI1SRC_1: /* PLLR is the clock source for SAI*/ - case RCC_DCKCFGR_SAI2SRC_1: /* PLLR is the clock source for SAI*/ - { - /* Configure the PLLI2S division factor */ - /* PLL_VCO Input = PLL_SOURCE/PLLM */ - if ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSI) - { - /* In Case the PLL Source is HSI (Internal Clock) */ - vcoinput = (HSI_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); - } - else - { - /* In Case the PLL Source is HSE (External Clock) */ - vcoinput = ((HSE_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM))); - } - - /* PLL_VCO Output = PLL_VCO Input * PLLN */ - /* SAI_CLK_x = PLL_VCO Output/PLLR */ - tmpreg1 = (RCC->PLLCFGR & RCC_PLLCFGR_PLLR) >> 28U; - frequency = (vcoinput * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6U)) / (tmpreg1); - break; - } - - case RCC_DCKCFGR_SAI1SRC: /* External clock is the clock source for SAI*/ - { - frequency = EXTERNAL_CLOCK_VALUE; - break; - } - - case RCC_DCKCFGR_SAI2SRC: /* PLLSRC(HSE or HSI) is the clock source for SAI*/ - { - if ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSI) - { - /* In Case the PLL Source is HSI (Internal Clock) */ - frequency = (uint32_t)(HSI_VALUE); - } - else - { - /* In Case the PLL Source is HSE (External Clock) */ - frequency = (uint32_t)(HSE_VALUE); - } - - break; - } - - default : - { - break; - } - } - } - - return frequency; -} - -#endif /* STM32F446xx */ - -#if defined(STM32F469xx) || defined(STM32F479xx) -/** - * @brief Initializes the RCC extended peripherals clocks according to the specified - * parameters in the RCC_PeriphCLKInitTypeDef. - * @param PeriphClkInit: pointer to an RCC_PeriphCLKInitTypeDef structure that - * contains the configuration information for the Extended Peripherals - * clocks(I2S, SAI, LTDC, RTC and TIM). - * - * @note Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select - * the RTC clock source; in this case the Backup domain will be reset in - * order to modify the RTC Clock source, as consequence RTC registers (including - * the backup registers) and RCC_BDCR register are set to their reset values. - * - * @retval HAL status - */ -HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit) -{ - uint32_t tickstart = 0U; - uint32_t tmpreg1 = 0U; - uint32_t pllsaip = 0U; - uint32_t pllsaiq = 0U; - uint32_t pllsair = 0U; - /* Check the parameters */ - assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection)); - - /*--------------------------- CLK48 Configuration --------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == RCC_PERIPHCLK_CLK48) - { - /* Check the parameters */ - assert_param(IS_RCC_CLK48CLKSOURCE(PeriphClkInit->Clk48ClockSelection)); - /* Configure the CLK48 clock source */ - __HAL_RCC_CLK48_CONFIG(PeriphClkInit->Clk48ClockSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*------------------------------ SDIO Configuration ------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SDIO) == RCC_PERIPHCLK_SDIO) - { - /* Check the parameters */ - assert_param(IS_RCC_SDIOCLKSOURCE(PeriphClkInit->SdioClockSelection)); - /* Configure the SDIO clock source */ - __HAL_RCC_SDIO_CONFIG(PeriphClkInit->SdioClockSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*----------------------- SAI/I2S Configuration (PLLI2S) -------------------*/ - /*------------------- Common configuration SAI/I2S -------------------------*/ - /* In Case of SAI or I2S Clock Configuration through PLLI2S, PLLI2SN division - factor is common parameters for both peripherals */ - if ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S) == RCC_PERIPHCLK_I2S) || - (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLI2S) == RCC_PERIPHCLK_SAI_PLLI2S) || - (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_PLLI2S) == RCC_PERIPHCLK_PLLI2S)) - { - /* check for Parameters */ - assert_param(IS_RCC_PLLI2SN_VALUE(PeriphClkInit->PLLI2S.PLLI2SN)); - /* Disable the PLLI2S */ - __HAL_RCC_PLLI2S_DISABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLI2S is disabled */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - - /*---------------------- I2S configuration -------------------------------*/ - /* In Case of I2S Clock Configuration through PLLI2S, PLLI2SR must be added - only for I2S configuration */ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S) == (RCC_PERIPHCLK_I2S)) - { - /* check for Parameters */ - assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); - /* Configure the PLLI2S division factors */ - /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) x (PLLI2SN/PLLM) */ - /* I2SCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SR */ - __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN, PeriphClkInit->PLLI2S.PLLI2SR); - } - - /*---------------------------- SAI configuration -------------------------*/ - /* In Case of SAI Clock Configuration through PLLI2S, PLLI2SQ and PLLI2S_DIVQ must - be added only for SAI configuration */ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLI2S) == (RCC_PERIPHCLK_SAI_PLLI2S)) - { - /* Check the PLLI2S division factors */ - assert_param(IS_RCC_PLLI2SQ_VALUE(PeriphClkInit->PLLI2S.PLLI2SQ)); - assert_param(IS_RCC_PLLI2S_DIVQ_VALUE(PeriphClkInit->PLLI2SDivQ)); - /* Read PLLI2SR value from PLLI2SCFGR register (this value is not need for SAI configuration) */ - tmpreg1 = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)); - /* Configure the PLLI2S division factors */ - /* PLLI2S_VCO Input = PLL_SOURCE/PLLM */ - /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ - /* SAI_CLK(first level) = PLLI2S_VCO Output/PLLI2SQ */ - __HAL_RCC_PLLI2S_SAICLK_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN, PeriphClkInit->PLLI2S.PLLI2SQ, tmpreg1); - /* SAI_CLK_x = SAI_CLK(first level)/PLLI2SDIVQ */ - __HAL_RCC_PLLI2S_PLLSAICLKDIVQ_CONFIG(PeriphClkInit->PLLI2SDivQ); - } - - /*----------------- In Case of PLLI2S is just selected -----------------*/ - if ((PeriphClkInit->PeriphClockSelection & RCC_PERIPHCLK_PLLI2S) == RCC_PERIPHCLK_PLLI2S) - { - /* Check for Parameters */ - assert_param(IS_RCC_PLLI2SQ_VALUE(PeriphClkInit->PLLI2S.PLLI2SQ)); - assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); - /* Configure the PLLI2S multiplication and division factors */ - __HAL_RCC_PLLI2S_SAICLK_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN, PeriphClkInit->PLLI2S.PLLI2SQ, PeriphClkInit->PLLI2S.PLLI2SR); - } - - /* Enable the PLLI2S */ - __HAL_RCC_PLLI2S_ENABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLI2S is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - } - - /*--------------------------------------------------------------------------*/ - - /*----------------------- SAI/LTDC Configuration (PLLSAI) ------------------*/ - /*----------------------- Common configuration SAI/LTDC --------------------*/ - /* In Case of SAI, LTDC or CLK48 Clock Configuration through PLLSAI, PLLSAIN division - factor is common parameters for these peripherals */ - if ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLSAI) == RCC_PERIPHCLK_SAI_PLLSAI) || - (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LTDC) == RCC_PERIPHCLK_LTDC) || - ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == RCC_PERIPHCLK_CLK48) && - (PeriphClkInit->Clk48ClockSelection == RCC_CLK48CLKSOURCE_PLLSAIP))) - { - /* Check the PLLSAI division factors */ - assert_param(IS_RCC_PLLSAIN_VALUE(PeriphClkInit->PLLSAI.PLLSAIN)); - /* Disable PLLSAI Clock */ - __HAL_RCC_PLLSAI_DISABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLSAI is disabled */ - while (__HAL_RCC_PLLSAI_GET_FLAG() != RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLSAI_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - - /*---------------------------- SAI configuration -------------------------*/ - /* In Case of SAI Clock Configuration through PLLSAI, PLLSAIQ and PLLSAI_DIVQ must - be added only for SAI configuration */ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLSAI) == (RCC_PERIPHCLK_SAI_PLLSAI)) - { - assert_param(IS_RCC_PLLSAIQ_VALUE(PeriphClkInit->PLLSAI.PLLSAIQ)); - assert_param(IS_RCC_PLLSAI_DIVQ_VALUE(PeriphClkInit->PLLSAIDivQ)); - /* Read PLLSAIP value from PLLSAICFGR register (this value is not needed for SAI configuration) */ - pllsaip = ((((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIP) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIP)) + 1U) << 1U); - /* Read PLLSAIR value from PLLSAICFGR register (this value is not need for SAI configuration) */ - pllsair = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIR) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIR)); - /* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ - /* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ - /* SAI_CLK(first level) = PLLSAI_VCO Output/PLLSAIQ */ - __HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIN, pllsaip, PeriphClkInit->PLLSAI.PLLSAIQ, pllsair); - /* SAI_CLK_x = SAI_CLK(first level)/PLLSAIDIVQ */ - __HAL_RCC_PLLSAI_PLLSAICLKDIVQ_CONFIG(PeriphClkInit->PLLSAIDivQ); - } - - /*---------------------------- LTDC configuration ------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LTDC) == (RCC_PERIPHCLK_LTDC)) - { - assert_param(IS_RCC_PLLSAIR_VALUE(PeriphClkInit->PLLSAI.PLLSAIR)); - assert_param(IS_RCC_PLLSAI_DIVR_VALUE(PeriphClkInit->PLLSAIDivR)); - /* Read PLLSAIP value from PLLSAICFGR register (this value is not needed for SAI configuration) */ - pllsaip = ((((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIP) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIP)) + 1U) << 1U); - /* Read PLLSAIQ value from PLLSAICFGR register (this value is not need for SAI configuration) */ - pllsaiq = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ)); - /* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ - /* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ - /* LTDC_CLK(first level) = PLLSAI_VCO Output/PLLSAIR */ - __HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIN, pllsaip, pllsaiq, PeriphClkInit->PLLSAI.PLLSAIR); - /* LTDC_CLK = LTDC_CLK(first level)/PLLSAIDIVR */ - __HAL_RCC_PLLSAI_PLLSAICLKDIVR_CONFIG(PeriphClkInit->PLLSAIDivR); - } - - /*---------------------------- CLK48 configuration ------------------------*/ - /* Configure the PLLSAI when it is used as clock source for CLK48 */ - if ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == (RCC_PERIPHCLK_CLK48)) && - (PeriphClkInit->Clk48ClockSelection == RCC_CLK48CLKSOURCE_PLLSAIP)) - { - assert_param(IS_RCC_PLLSAIP_VALUE(PeriphClkInit->PLLSAI.PLLSAIP)); - /* Read PLLSAIQ value from PLLSAICFGR register (this value is not need for SAI configuration) */ - pllsaiq = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ)); - /* Read PLLSAIR value from PLLSAICFGR register (this value is not need for SAI configuration) */ - pllsair = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIR) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIR)); - /* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ - /* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ - /* CLK48_CLK(first level) = PLLSAI_VCO Output/PLLSAIP */ - __HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIN, PeriphClkInit->PLLSAI.PLLSAIP, pllsaiq, pllsair); - } - - /* Enable PLLSAI Clock */ - __HAL_RCC_PLLSAI_ENABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLSAI is ready */ - while (__HAL_RCC_PLLSAI_GET_FLAG() == RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLSAI_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - } - - /*--------------------------------------------------------------------------*/ - - /*---------------------------- RTC configuration ---------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == (RCC_PERIPHCLK_RTC)) - { - /* Check for RTC Parameters used to output RTCCLK */ - assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection)); - /* Enable Power Clock*/ - __HAL_RCC_PWR_CLK_ENABLE(); - /* Enable write access to Backup domain */ - PWR->CR |= PWR_CR_DBP; - /* Get tick */ - tickstart = HAL_GetTick(); - - while ((PWR->CR & PWR_CR_DBP) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Reset the Backup domain only if the RTC Clock source selection is modified from reset value */ - tmpreg1 = (RCC->BDCR & RCC_BDCR_RTCSEL); - - if ((tmpreg1 != 0x00000000U) && ((tmpreg1) != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL))) - { - /* Store the content of BDCR register before the reset of Backup Domain */ - tmpreg1 = (RCC->BDCR & ~(RCC_BDCR_RTCSEL)); - /* RTC Clock selection can be changed only if the Backup Domain is reset */ - __HAL_RCC_BACKUPRESET_FORCE(); - __HAL_RCC_BACKUPRESET_RELEASE(); - /* Restore the Content of BDCR register */ - RCC->BDCR = tmpreg1; - - /* Wait for LSE reactivation if LSE was enable prior to Backup Domain reset */ - if (HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSEON)) - { - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till LSE is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - - __HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*---------------------------- TIM configuration ---------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_TIM) == (RCC_PERIPHCLK_TIM)) - { - __HAL_RCC_TIMCLKPRESCALER(PeriphClkInit->TIMPresSelection); - } - - return HAL_OK; -} - -/** - * @brief Configures the RCC_PeriphCLKInitTypeDef according to the internal - * RCC configuration registers. - * @param PeriphClkInit: pointer to an RCC_PeriphCLKInitTypeDef structure that - * will be configured. - * @retval None - */ -void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit) -{ - uint32_t tempreg; - /* Set all possible values for the extended clock type parameter------------*/ - PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_I2S | RCC_PERIPHCLK_SAI_PLLSAI | \ - RCC_PERIPHCLK_SAI_PLLI2S | RCC_PERIPHCLK_LTDC | \ - RCC_PERIPHCLK_TIM | RCC_PERIPHCLK_RTC | \ - RCC_PERIPHCLK_CLK48 | RCC_PERIPHCLK_SDIO; - /* Get the PLLI2S Clock configuration --------------------------------------*/ - PeriphClkInit->PLLI2S.PLLI2SN = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)); - PeriphClkInit->PLLI2S.PLLI2SR = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)); - PeriphClkInit->PLLI2S.PLLI2SQ = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SQ)); - /* Get the PLLSAI Clock configuration --------------------------------------*/ - PeriphClkInit->PLLSAI.PLLSAIN = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIN) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIN)); - PeriphClkInit->PLLSAI.PLLSAIR = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIR) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIR)); - PeriphClkInit->PLLSAI.PLLSAIQ = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ)); - /* Get the PLLSAI/PLLI2S division factors ----------------------------------*/ - PeriphClkInit->PLLI2SDivQ = (uint32_t)((RCC->DCKCFGR & RCC_DCKCFGR_PLLI2SDIVQ) >> POSITION_VAL(RCC_DCKCFGR_PLLI2SDIVQ)); - PeriphClkInit->PLLSAIDivQ = (uint32_t)((RCC->DCKCFGR & RCC_DCKCFGR_PLLSAIDIVQ) >> POSITION_VAL(RCC_DCKCFGR_PLLSAIDIVQ)); - PeriphClkInit->PLLSAIDivR = (uint32_t)(RCC->DCKCFGR & RCC_DCKCFGR_PLLSAIDIVR); - /* Get the RTC Clock configuration -----------------------------------------*/ - tempreg = (RCC->CFGR & RCC_CFGR_RTCPRE); - PeriphClkInit->RTCClockSelection = (uint32_t)((tempreg) | (RCC->BDCR & RCC_BDCR_RTCSEL)); - /* Get the CLK48 clock configuration -------------------------------------*/ - PeriphClkInit->Clk48ClockSelection = __HAL_RCC_GET_CLK48_SOURCE(); - /* Get the SDIO clock configuration ----------------------------------------*/ - PeriphClkInit->SdioClockSelection = __HAL_RCC_GET_SDIO_SOURCE(); - - if ((RCC->DCKCFGR & RCC_DCKCFGR_TIMPRE) == RESET) - { - PeriphClkInit->TIMPresSelection = RCC_TIMPRES_DESACTIVATED; - } - else - { - PeriphClkInit->TIMPresSelection = RCC_TIMPRES_ACTIVATED; - } -} -#endif /* STM32F469xx || STM32F479xx */ - -#if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -/** - * @brief Initializes the RCC extended peripherals clocks according to the specified - * parameters in the RCC_PeriphCLKInitTypeDef. - * @param PeriphClkInit: pointer to an RCC_PeriphCLKInitTypeDef structure that - * contains the configuration information for the Extended Peripherals - * clocks(I2S, LTDC RTC and TIM). - * - * @note Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select - * the RTC clock source; in this case the Backup domain will be reset in - * order to modify the RTC Clock source, as consequence RTC registers (including - * the backup registers) and RCC_BDCR register are set to their reset values. - * - * @retval HAL status - */ -HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit) -{ - uint32_t tickstart = 0U; - uint32_t tmpreg1 = 0U; - uint32_t plli2sq = 0U; - uint32_t plli2sused = 0U; - /* Check the peripheral clock selection parameters */ - assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection)); - - /*----------------------------------- I2S APB1 configuration ---------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB1) == (RCC_PERIPHCLK_I2S_APB1)) - { - /* Check the parameters */ - assert_param(IS_RCC_I2SAPB1CLKSOURCE(PeriphClkInit->I2sApb1ClockSelection)); - /* Configure I2S Clock source */ - __HAL_RCC_I2S_APB1_CONFIG(PeriphClkInit->I2sApb1ClockSelection); - - /* Enable the PLLI2S when it's used as clock source for I2S */ - if (PeriphClkInit->I2sApb1ClockSelection == RCC_I2SAPB1CLKSOURCE_PLLI2S) - { - plli2sused = 1U; - } - } - - /*--------------------------------------------------------------------------*/ - - /*----------------------------------- I2S APB2 configuration ---------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB2) == (RCC_PERIPHCLK_I2S_APB2)) - { - /* Check the parameters */ - assert_param(IS_RCC_I2SAPB2CLKSOURCE(PeriphClkInit->I2sApb2ClockSelection)); - /* Configure I2S Clock source */ - __HAL_RCC_I2S_APB2_CONFIG(PeriphClkInit->I2sApb2ClockSelection); - - /* Enable the PLLI2S when it's used as clock source for I2S */ - if (PeriphClkInit->I2sApb2ClockSelection == RCC_I2SAPB2CLKSOURCE_PLLI2S) - { - plli2sused = 1U; - } - } - - /*--------------------------------------------------------------------------*/ - - /*------------------------------------ RTC configuration -------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == (RCC_PERIPHCLK_RTC)) - { - /* Check for RTC Parameters used to output RTCCLK */ - assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection)); - /* Enable Power Clock*/ - __HAL_RCC_PWR_CLK_ENABLE(); - /* Enable write access to Backup domain */ - PWR->CR |= PWR_CR_DBP; - /* Get tick */ - tickstart = HAL_GetTick(); - - while ((PWR->CR & PWR_CR_DBP) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Reset the Backup domain only if the RTC Clock source selection is modified from reset value */ - tmpreg1 = (RCC->BDCR & RCC_BDCR_RTCSEL); - - if ((tmpreg1 != 0x00000000U) && ((tmpreg1) != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL))) - { - /* Store the content of BDCR register before the reset of Backup Domain */ - tmpreg1 = (RCC->BDCR & ~(RCC_BDCR_RTCSEL)); - /* RTC Clock selection can be changed only if the Backup Domain is reset */ - __HAL_RCC_BACKUPRESET_FORCE(); - __HAL_RCC_BACKUPRESET_RELEASE(); - /* Restore the Content of BDCR register */ - RCC->BDCR = tmpreg1; - - /* Wait for LSE reactivation if LSE was enable prior to Backup Domain reset */ - if (HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSEON)) - { - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till LSE is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - - __HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*------------------------------------ TIM configuration -------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_TIM) == (RCC_PERIPHCLK_TIM)) - { - /* Configure Timer Prescaler */ - __HAL_RCC_TIMCLKPRESCALER(PeriphClkInit->TIMPresSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*------------------------------------- FMPI2C1 Configuration --------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_FMPI2C1) == RCC_PERIPHCLK_FMPI2C1) - { - /* Check the parameters */ - assert_param(IS_RCC_FMPI2C1CLKSOURCE(PeriphClkInit->Fmpi2c1ClockSelection)); - /* Configure the FMPI2C1 clock source */ - __HAL_RCC_FMPI2C1_CONFIG(PeriphClkInit->Fmpi2c1ClockSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*------------------------------------- CLK48 Configuration ----------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == RCC_PERIPHCLK_CLK48) - { - /* Check the parameters */ - assert_param(IS_RCC_CLK48CLKSOURCE(PeriphClkInit->Clk48ClockSelection)); - /* Configure the SDIO clock source */ - __HAL_RCC_CLK48_CONFIG(PeriphClkInit->Clk48ClockSelection); - - /* Enable the PLLI2S when it's used as clock source for CLK48 */ - if (PeriphClkInit->Clk48ClockSelection == RCC_CLK48CLKSOURCE_PLLI2SQ) - { - plli2sused = 1U; - } - } - - /*--------------------------------------------------------------------------*/ - - /*------------------------------------- SDIO Configuration -----------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SDIO) == RCC_PERIPHCLK_SDIO) - { - /* Check the parameters */ - assert_param(IS_RCC_SDIOCLKSOURCE(PeriphClkInit->SdioClockSelection)); - /* Configure the SDIO clock source */ - __HAL_RCC_SDIO_CONFIG(PeriphClkInit->SdioClockSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*-------------------------------------- PLLI2S Configuration --------------*/ - /* PLLI2S is configured when a peripheral will use it as source clock : I2S on APB1 or - I2S on APB2*/ - if ((plli2sused == 1U) || (PeriphClkInit->PeriphClockSelection == RCC_PERIPHCLK_PLLI2S)) - { - /* Disable the PLLI2S */ - __HAL_RCC_PLLI2S_DISABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLI2S is disabled */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - - /* check for common PLLI2S Parameters */ - assert_param(IS_RCC_PLLI2SCLKSOURCE(PeriphClkInit->PLLI2SSelection)); - assert_param(IS_RCC_PLLI2SM_VALUE(PeriphClkInit->PLLI2S.PLLI2SM)); - assert_param(IS_RCC_PLLI2SN_VALUE(PeriphClkInit->PLLI2S.PLLI2SN)); - /*-------------------- Set the PLL I2S clock -----------------------------*/ - __HAL_RCC_PLL_I2S_CONFIG(PeriphClkInit->PLLI2SSelection); - - /*------- In Case of PLLI2S is selected as source clock for I2S ----------*/ - if (((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB1) == RCC_PERIPHCLK_I2S_APB1) && (PeriphClkInit->I2sApb1ClockSelection == RCC_I2SAPB1CLKSOURCE_PLLI2S)) || - ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB2) == RCC_PERIPHCLK_I2S_APB2) && (PeriphClkInit->I2sApb2ClockSelection == RCC_I2SAPB2CLKSOURCE_PLLI2S)) || - ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == RCC_PERIPHCLK_CLK48) && (PeriphClkInit->Clk48ClockSelection == RCC_CLK48CLKSOURCE_PLLI2SQ)) || - ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SDIO) == RCC_PERIPHCLK_SDIO) && (PeriphClkInit->SdioClockSelection == RCC_SDIOCLKSOURCE_CLK48) && (PeriphClkInit->Clk48ClockSelection == RCC_CLK48CLKSOURCE_PLLI2SQ))) - { - /* check for Parameters */ - assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); - /* Read PLLI2SQ value from PLLI2SCFGR register (this value is not needed for I2S configuration) */ - plli2sq = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SQ)); - /* Configure the PLLI2S division factors */ - /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLI2SM)*/ - /* I2SCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SR */ - __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SM, PeriphClkInit->PLLI2S.PLLI2SN, plli2sq, PeriphClkInit->PLLI2S.PLLI2SR); - } - - /*----------------- In Case of PLLI2S is just selected ------------------*/ - if ((PeriphClkInit->PeriphClockSelection & RCC_PERIPHCLK_PLLI2S) == RCC_PERIPHCLK_PLLI2S) - { - /* Check for Parameters */ - assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); - assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SQ)); - /* Configure the PLLI2S division factors */ - /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLI2SM)*/ - /* SPDIFRXCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SP */ - __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SM, PeriphClkInit->PLLI2S.PLLI2SN, PeriphClkInit->PLLI2S.PLLI2SQ, PeriphClkInit->PLLI2S.PLLI2SR); - } - - /* Enable the PLLI2S */ - __HAL_RCC_PLLI2S_ENABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLI2S is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - } - - /*--------------------------------------------------------------------------*/ - - /*-------------------- DFSDM1 clock source configuration -------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_DFSDM1) == RCC_PERIPHCLK_DFSDM1) - { - /* Check the parameters */ - assert_param(IS_RCC_DFSDM1CLKSOURCE(PeriphClkInit->Dfsdm1ClockSelection)); - /* Configure the DFSDM1 interface clock source */ - __HAL_RCC_DFSDM1_CONFIG(PeriphClkInit->Dfsdm1ClockSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*-------------------- DFSDM1 Audio clock source configuration -------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_DFSDM1_AUDIO) == RCC_PERIPHCLK_DFSDM1_AUDIO) - { - /* Check the parameters */ - assert_param(IS_RCC_DFSDM1AUDIOCLKSOURCE(PeriphClkInit->Dfsdm1AudioClockSelection)); - /* Configure the DFSDM1 Audio interface clock source */ - __HAL_RCC_DFSDM1AUDIO_CONFIG(PeriphClkInit->Dfsdm1AudioClockSelection); - } - - return HAL_OK; -} - -/** - * @brief Get the RCC_PeriphCLKInitTypeDef according to the internal - * RCC configuration registers. - * @param PeriphClkInit: pointer to an RCC_PeriphCLKInitTypeDef structure that - * will be configured. - * @retval None - */ -void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit) -{ - uint32_t tempreg; - /* Set all possible values for the extended clock type parameter------------*/ - PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_I2S_APB1 | RCC_PERIPHCLK_I2S_APB2 | \ - RCC_PERIPHCLK_TIM | RCC_PERIPHCLK_RTC | \ - RCC_PERIPHCLK_FMPI2C1 | RCC_PERIPHCLK_CLK48 | \ - RCC_PERIPHCLK_SDIO; - /* Get the PLLI2S Clock configuration --------------------------------------*/ - PeriphClkInit->PLLI2S.PLLI2SM = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SM)); - PeriphClkInit->PLLI2S.PLLI2SN = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)); - PeriphClkInit->PLLI2S.PLLI2SQ = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SQ)); - PeriphClkInit->PLLI2S.PLLI2SR = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)); - /* Get the I2S APB1 clock configuration ------------------------------------*/ - PeriphClkInit->I2sApb1ClockSelection = __HAL_RCC_GET_I2S_APB1_SOURCE(); - /* Get the I2S APB2 clock configuration ------------------------------------*/ - PeriphClkInit->I2sApb2ClockSelection = __HAL_RCC_GET_I2S_APB2_SOURCE(); - /* Get the RTC Clock configuration -----------------------------------------*/ - tempreg = (RCC->CFGR & RCC_CFGR_RTCPRE); - PeriphClkInit->RTCClockSelection = (uint32_t)((tempreg) | (RCC->BDCR & RCC_BDCR_RTCSEL)); - /* Get the FMPI2C1 clock configuration -------------------------------------*/ - PeriphClkInit->Fmpi2c1ClockSelection = __HAL_RCC_GET_FMPI2C1_SOURCE(); - /* Get the CLK48 clock configuration ----------------------------------------*/ - PeriphClkInit->Clk48ClockSelection = __HAL_RCC_GET_CLK48_SOURCE(); - /* Get the SDIO clock configuration ----------------------------------------*/ - PeriphClkInit->SdioClockSelection = __HAL_RCC_GET_SDIO_SOURCE(); - - /* Get the TIM Prescaler configuration -------------------------------------*/ - if ((RCC->DCKCFGR & RCC_DCKCFGR_TIMPRE) == RESET) - { - PeriphClkInit->TIMPresSelection = RCC_TIMPRES_DESACTIVATED; - } - else - { - PeriphClkInit->TIMPresSelection = RCC_TIMPRES_ACTIVATED; - } -} -#endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) -/** - * @brief Initializes the RCC extended peripherals clocks according to the specified parameters in the - * RCC_PeriphCLKInitTypeDef. - * @param PeriphClkInit: pointer to an RCC_PeriphCLKInitTypeDef structure that - * contains the configuration information for the Extended Peripherals clocks(I2S and RTC clocks). - * - * @note A caution to be taken when HAL_RCCEx_PeriphCLKConfig() is used to select RTC clock selection, in this case - * the Reset of Backup domain will be applied in order to modify the RTC Clock source as consequence all backup - * domain (RTC and RCC_BDCR register expect BKPSRAM) will be reset - * - * @retval HAL status - */ -HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit) -{ - uint32_t tickstart = 0U; - uint32_t tmpreg1 = 0U; - /* Check the parameters */ - assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection)); - - /*---------------------------- RTC configuration ---------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == (RCC_PERIPHCLK_RTC)) - { - /* Check for RTC Parameters used to output RTCCLK */ - assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection)); - /* Enable Power Clock*/ - __HAL_RCC_PWR_CLK_ENABLE(); - /* Enable write access to Backup domain */ - PWR->CR |= PWR_CR_DBP; - /* Get tick */ - tickstart = HAL_GetTick(); - - while ((PWR->CR & PWR_CR_DBP) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Reset the Backup domain only if the RTC Clock source selection is modified from reset value */ - tmpreg1 = (RCC->BDCR & RCC_BDCR_RTCSEL); - - if ((tmpreg1 != 0x00000000U) && ((tmpreg1) != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL))) - { - /* Store the content of BDCR register before the reset of Backup Domain */ - tmpreg1 = (RCC->BDCR & ~(RCC_BDCR_RTCSEL)); - /* RTC Clock selection can be changed only if the Backup Domain is reset */ - __HAL_RCC_BACKUPRESET_FORCE(); - __HAL_RCC_BACKUPRESET_RELEASE(); - /* Restore the Content of BDCR register */ - RCC->BDCR = tmpreg1; - - /* Wait for LSE reactivation if LSE was enable prior to Backup Domain reset */ - if (HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSEON)) - { - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till LSE is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - - __HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*---------------------------- TIM configuration ---------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_TIM) == (RCC_PERIPHCLK_TIM)) - { - __HAL_RCC_TIMCLKPRESCALER(PeriphClkInit->TIMPresSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*---------------------------- FMPI2C1 Configuration -----------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_FMPI2C1) == RCC_PERIPHCLK_FMPI2C1) - { - /* Check the parameters */ - assert_param(IS_RCC_FMPI2C1CLKSOURCE(PeriphClkInit->Fmpi2c1ClockSelection)); - /* Configure the FMPI2C1 clock source */ - __HAL_RCC_FMPI2C1_CONFIG(PeriphClkInit->Fmpi2c1ClockSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*---------------------------- LPTIM1 Configuration ------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LPTIM1) == RCC_PERIPHCLK_LPTIM1) - { - /* Check the parameters */ - assert_param(IS_RCC_LPTIM1CLKSOURCE(PeriphClkInit->Lptim1ClockSelection)); - /* Configure the LPTIM1 clock source */ - __HAL_RCC_LPTIM1_CONFIG(PeriphClkInit->Lptim1ClockSelection); - } - - /*---------------------------- I2S Configuration ------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S) == RCC_PERIPHCLK_I2S) - { - /* Check the parameters */ - assert_param(IS_RCC_I2SAPBCLKSOURCE(PeriphClkInit->I2SClockSelection)); - /* Configure the I2S clock source */ - __HAL_RCC_I2S_CONFIG(PeriphClkInit->I2SClockSelection); - } - - return HAL_OK; -} - -/** - * @brief Configures the RCC_OscInitStruct according to the internal - * RCC configuration registers. - * @param PeriphClkInit: pointer to an RCC_PeriphCLKInitTypeDef structure that - * will be configured. - * @retval None - */ -void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit) -{ - uint32_t tempreg; - /* Set all possible values for the extended clock type parameter------------*/ - PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_FMPI2C1 | RCC_PERIPHCLK_LPTIM1 | RCC_PERIPHCLK_TIM | RCC_PERIPHCLK_RTC; - tempreg = (RCC->CFGR & RCC_CFGR_RTCPRE); - PeriphClkInit->RTCClockSelection = (uint32_t)((tempreg) | (RCC->BDCR & RCC_BDCR_RTCSEL)); - - if ((RCC->DCKCFGR & RCC_DCKCFGR_TIMPRE) == RESET) - { - PeriphClkInit->TIMPresSelection = RCC_TIMPRES_DESACTIVATED; - } - else - { - PeriphClkInit->TIMPresSelection = RCC_TIMPRES_ACTIVATED; - } - - /* Get the FMPI2C1 clock configuration -------------------------------------*/ - PeriphClkInit->Fmpi2c1ClockSelection = __HAL_RCC_GET_FMPI2C1_SOURCE(); - /* Get the I2S clock configuration -----------------------------------------*/ - PeriphClkInit->I2SClockSelection = __HAL_RCC_GET_I2S_SOURCE(); -} -#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ - -#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) -/** - * @brief Initializes the RCC extended peripherals clocks according to the specified - * parameters in the RCC_PeriphCLKInitTypeDef. - * @param PeriphClkInit: pointer to an RCC_PeriphCLKInitTypeDef structure that - * contains the configuration information for the Extended Peripherals - * clocks(I2S, SAI, LTDC RTC and TIM). - * - * @note Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select - * the RTC clock source; in this case the Backup domain will be reset in - * order to modify the RTC Clock source, as consequence RTC registers (including - * the backup registers) and RCC_BDCR register are set to their reset values. - * - * @retval HAL status - */ -HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit) -{ - uint32_t tickstart = 0U; - uint32_t tmpreg1 = 0U; - /* Check the parameters */ - assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection)); - - /*----------------------- SAI/I2S Configuration (PLLI2S) -------------------*/ - /*----------------------- Common configuration SAI/I2S ----------------------*/ - /* In Case of SAI or I2S Clock Configuration through PLLI2S, PLLI2SN division - factor is common parameters for both peripherals */ - if ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S) == RCC_PERIPHCLK_I2S) || - (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLI2S) == RCC_PERIPHCLK_SAI_PLLI2S)) - { - /* check for Parameters */ - assert_param(IS_RCC_PLLI2SN_VALUE(PeriphClkInit->PLLI2S.PLLI2SN)); - /* Disable the PLLI2S */ - __HAL_RCC_PLLI2S_DISABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLI2S is disabled */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - - /*---------------------------- I2S configuration -------------------------------*/ - /* In Case of I2S Clock Configuration through PLLI2S, PLLI2SR must be added - only for I2S configuration */ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S) == (RCC_PERIPHCLK_I2S)) - { - /* check for Parameters */ - assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); - /* Configure the PLLI2S division factors */ - /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLM) */ - /* I2SCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SR */ - __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN, PeriphClkInit->PLLI2S.PLLI2SR); - } - - /*---------------------------- SAI configuration -------------------------------*/ - /* In Case of SAI Clock Configuration through PLLI2S, PLLI2SQ and PLLI2S_DIVQ must - be added only for SAI configuration */ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLI2S) == (RCC_PERIPHCLK_SAI_PLLI2S)) - { - /* Check the PLLI2S division factors */ - assert_param(IS_RCC_PLLI2SQ_VALUE(PeriphClkInit->PLLI2S.PLLI2SQ)); - assert_param(IS_RCC_PLLI2S_DIVQ_VALUE(PeriphClkInit->PLLI2SDivQ)); - /* Read PLLI2SR value from PLLI2SCFGR register (this value is not need for SAI configuration) */ - tmpreg1 = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)); - /* Configure the PLLI2S division factors */ - /* PLLI2S_VCO Input = PLL_SOURCE/PLLM */ - /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ - /* SAI_CLK(first level) = PLLI2S_VCO Output/PLLI2SQ */ - __HAL_RCC_PLLI2S_SAICLK_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN, PeriphClkInit->PLLI2S.PLLI2SQ, tmpreg1); - /* SAI_CLK_x = SAI_CLK(first level)/PLLI2SDIVQ */ - __HAL_RCC_PLLI2S_PLLSAICLKDIVQ_CONFIG(PeriphClkInit->PLLI2SDivQ); - } - - /* Enable the PLLI2S */ - __HAL_RCC_PLLI2S_ENABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLI2S is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - } - - /*--------------------------------------------------------------------------*/ - - /*----------------------- SAI/LTDC Configuration (PLLSAI) ------------------*/ - /*----------------------- Common configuration SAI/LTDC --------------------*/ - /* In Case of SAI or LTDC Clock Configuration through PLLSAI, PLLSAIN division - factor is common parameters for both peripherals */ - if ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLSAI) == RCC_PERIPHCLK_SAI_PLLSAI) || - (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LTDC) == RCC_PERIPHCLK_LTDC)) - { - /* Check the PLLSAI division factors */ - assert_param(IS_RCC_PLLSAIN_VALUE(PeriphClkInit->PLLSAI.PLLSAIN)); - /* Disable PLLSAI Clock */ - __HAL_RCC_PLLSAI_DISABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLSAI is disabled */ - while (__HAL_RCC_PLLSAI_GET_FLAG() != RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLSAI_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - - /*---------------------------- SAI configuration -------------------------*/ - /* In Case of SAI Clock Configuration through PLLSAI, PLLSAIQ and PLLSAI_DIVQ must - be added only for SAI configuration */ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLSAI) == (RCC_PERIPHCLK_SAI_PLLSAI)) - { - assert_param(IS_RCC_PLLSAIQ_VALUE(PeriphClkInit->PLLSAI.PLLSAIQ)); - assert_param(IS_RCC_PLLSAI_DIVQ_VALUE(PeriphClkInit->PLLSAIDivQ)); - /* Read PLLSAIR value from PLLSAICFGR register (this value is not need for SAI configuration) */ - tmpreg1 = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIR) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIR)); - /* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ - /* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ - /* SAI_CLK(first level) = PLLSAI_VCO Output/PLLSAIQ */ - __HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIN, PeriphClkInit->PLLSAI.PLLSAIQ, tmpreg1); - /* SAI_CLK_x = SAI_CLK(first level)/PLLSAIDIVQ */ - __HAL_RCC_PLLSAI_PLLSAICLKDIVQ_CONFIG(PeriphClkInit->PLLSAIDivQ); - } - - /*---------------------------- LTDC configuration ------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LTDC) == (RCC_PERIPHCLK_LTDC)) - { - assert_param(IS_RCC_PLLSAIR_VALUE(PeriphClkInit->PLLSAI.PLLSAIR)); - assert_param(IS_RCC_PLLSAI_DIVR_VALUE(PeriphClkInit->PLLSAIDivR)); - /* Read PLLSAIR value from PLLSAICFGR register (this value is not need for SAI configuration) */ - tmpreg1 = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ)); - /* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ - /* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ - /* LTDC_CLK(first level) = PLLSAI_VCO Output/PLLSAIR */ - __HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIN, tmpreg1, PeriphClkInit->PLLSAI.PLLSAIR); - /* LTDC_CLK = LTDC_CLK(first level)/PLLSAIDIVR */ - __HAL_RCC_PLLSAI_PLLSAICLKDIVR_CONFIG(PeriphClkInit->PLLSAIDivR); - } - - /* Enable PLLSAI Clock */ - __HAL_RCC_PLLSAI_ENABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLSAI is ready */ - while (__HAL_RCC_PLLSAI_GET_FLAG() == RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLSAI_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - } - - /*--------------------------------------------------------------------------*/ - - /*---------------------------- RTC configuration ---------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == (RCC_PERIPHCLK_RTC)) - { - /* Check for RTC Parameters used to output RTCCLK */ - assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection)); - /* Enable Power Clock*/ - __HAL_RCC_PWR_CLK_ENABLE(); - /* Enable write access to Backup domain */ - PWR->CR |= PWR_CR_DBP; - /* Get tick */ - tickstart = HAL_GetTick(); - - while ((PWR->CR & PWR_CR_DBP) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Reset the Backup domain only if the RTC Clock source selection is modified from reset value */ - tmpreg1 = (RCC->BDCR & RCC_BDCR_RTCSEL); - - if ((tmpreg1 != 0x00000000U) && ((tmpreg1) != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL))) - { - /* Store the content of BDCR register before the reset of Backup Domain */ - tmpreg1 = (RCC->BDCR & ~(RCC_BDCR_RTCSEL)); - /* RTC Clock selection can be changed only if the Backup Domain is reset */ - __HAL_RCC_BACKUPRESET_FORCE(); - __HAL_RCC_BACKUPRESET_RELEASE(); - /* Restore the Content of BDCR register */ - RCC->BDCR = tmpreg1; - - /* Wait for LSE reactivation if LSE was enable prior to Backup Domain reset */ - if (HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSEON)) - { - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till LSE is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - - __HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection); - } - - /*--------------------------------------------------------------------------*/ - - /*---------------------------- TIM configuration ---------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_TIM) == (RCC_PERIPHCLK_TIM)) - { - __HAL_RCC_TIMCLKPRESCALER(PeriphClkInit->TIMPresSelection); - } - - return HAL_OK; -} - -/** - * @brief Configures the PeriphClkInit according to the internal - * RCC configuration registers. - * @param PeriphClkInit: pointer to an RCC_PeriphCLKInitTypeDef structure that - * will be configured. - * @retval None - */ -void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit) -{ - uint32_t tempreg; - /* Set all possible values for the extended clock type parameter------------*/ - PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_I2S | RCC_PERIPHCLK_SAI_PLLSAI | RCC_PERIPHCLK_SAI_PLLI2S | RCC_PERIPHCLK_LTDC | RCC_PERIPHCLK_TIM | RCC_PERIPHCLK_RTC; - /* Get the PLLI2S Clock configuration -----------------------------------------------*/ - PeriphClkInit->PLLI2S.PLLI2SN = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)); - PeriphClkInit->PLLI2S.PLLI2SR = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)); - PeriphClkInit->PLLI2S.PLLI2SQ = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SQ)); - /* Get the PLLSAI Clock configuration -----------------------------------------------*/ - PeriphClkInit->PLLSAI.PLLSAIN = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIN) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIN)); - PeriphClkInit->PLLSAI.PLLSAIR = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIR) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIR)); - PeriphClkInit->PLLSAI.PLLSAIQ = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ)); - /* Get the PLLSAI/PLLI2S division factors -----------------------------------------------*/ - PeriphClkInit->PLLI2SDivQ = (uint32_t)((RCC->DCKCFGR & RCC_DCKCFGR_PLLI2SDIVQ) >> POSITION_VAL(RCC_DCKCFGR_PLLI2SDIVQ)); - PeriphClkInit->PLLSAIDivQ = (uint32_t)((RCC->DCKCFGR & RCC_DCKCFGR_PLLSAIDIVQ) >> POSITION_VAL(RCC_DCKCFGR_PLLSAIDIVQ)); - PeriphClkInit->PLLSAIDivR = (uint32_t)(RCC->DCKCFGR & RCC_DCKCFGR_PLLSAIDIVR); - /* Get the RTC Clock configuration -----------------------------------------------*/ - tempreg = (RCC->CFGR & RCC_CFGR_RTCPRE); - PeriphClkInit->RTCClockSelection = (uint32_t)((tempreg) | (RCC->BDCR & RCC_BDCR_RTCSEL)); - - if ((RCC->DCKCFGR & RCC_DCKCFGR_TIMPRE) == RESET) - { - PeriphClkInit->TIMPresSelection = RCC_TIMPRES_DESACTIVATED; - } - else - { - PeriphClkInit->TIMPresSelection = RCC_TIMPRES_ACTIVATED; - } -} - -#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */ - -#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx) ||\ - defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) -/** - * @brief Initializes the RCC extended peripherals clocks according to the specified parameters in the - * RCC_PeriphCLKInitTypeDef. - * @param PeriphClkInit: pointer to an RCC_PeriphCLKInitTypeDef structure that - * contains the configuration information for the Extended Peripherals clocks(I2S and RTC clocks). - * - * @note A caution to be taken when HAL_RCCEx_PeriphCLKConfig() is used to select RTC clock selection, in this case - * the Reset of Backup domain will be applied in order to modify the RTC Clock source as consequence all backup - * domain (RTC and RCC_BDCR register expect BKPSRAM) will be reset - * - * @retval HAL status - */ -HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit) -{ - uint32_t tickstart = 0U; - uint32_t tmpreg1 = 0U; - /* Check the parameters */ - assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection)); - - /*---------------------------- I2S configuration ---------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S) == (RCC_PERIPHCLK_I2S)) - { - /* check for Parameters */ - assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); - assert_param(IS_RCC_PLLI2SN_VALUE(PeriphClkInit->PLLI2S.PLLI2SN)); -#if defined(STM32F411xE) - assert_param(IS_RCC_PLLI2SM_VALUE(PeriphClkInit->PLLI2S.PLLI2SM)); -#endif /* STM32F411xE */ - /* Disable the PLLI2S */ - __HAL_RCC_PLLI2S_DISABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLI2S is disabled */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - -#if defined(STM32F411xE) - /* Configure the PLLI2S division factors */ - /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLI2SM) */ - /* I2SCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SR */ - __HAL_RCC_PLLI2S_I2SCLK_CONFIG(PeriphClkInit->PLLI2S.PLLI2SM, PeriphClkInit->PLLI2S.PLLI2SN, PeriphClkInit->PLLI2S.PLLI2SR); -#else - /* Configure the PLLI2S division factors */ - /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLM) */ - /* I2SCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SR */ - __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN, PeriphClkInit->PLLI2S.PLLI2SR); -#endif /* STM32F411xE */ - /* Enable the PLLI2S */ - __HAL_RCC_PLLI2S_ENABLE(); - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till PLLI2S is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) - { - /* return in case of Timeout detected */ - return HAL_TIMEOUT; - } - } - } - - /*---------------------------- RTC configuration ---------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == (RCC_PERIPHCLK_RTC)) - { - /* Check for RTC Parameters used to output RTCCLK */ - assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection)); - /* Enable Power Clock*/ - __HAL_RCC_PWR_CLK_ENABLE(); - /* Enable write access to Backup domain */ - PWR->CR |= PWR_CR_DBP; - /* Get tick */ - tickstart = HAL_GetTick(); - - while ((PWR->CR & PWR_CR_DBP) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Reset the Backup domain only if the RTC Clock source selection is modified from reset value */ - tmpreg1 = (RCC->BDCR & RCC_BDCR_RTCSEL); - - if ((tmpreg1 != 0x00000000U) && ((tmpreg1) != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL))) - { - /* Store the content of BDCR register before the reset of Backup Domain */ - tmpreg1 = (RCC->BDCR & ~(RCC_BDCR_RTCSEL)); - /* RTC Clock selection can be changed only if the Backup Domain is reset */ - __HAL_RCC_BACKUPRESET_FORCE(); - __HAL_RCC_BACKUPRESET_RELEASE(); - /* Restore the Content of BDCR register */ - RCC->BDCR = tmpreg1; - - /* Wait for LSE reactivation if LSE was enable prior to Backup Domain reset */ - if (HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSEON)) - { - /* Get tick */ - tickstart = HAL_GetTick(); - - /* Wait till LSE is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - - __HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection); - } - -#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) - - /*---------------------------- TIM configuration ---------------------------*/ - if (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_TIM) == (RCC_PERIPHCLK_TIM)) - { - __HAL_RCC_TIMCLKPRESCALER(PeriphClkInit->TIMPresSelection); - } - -#endif /* STM32F401xC || STM32F401xE || STM32F411xE */ - return HAL_OK; -} - -/** - * @brief Configures the RCC_OscInitStruct according to the internal - * RCC configuration registers. - * @param PeriphClkInit: pointer to an RCC_PeriphCLKInitTypeDef structure that - * will be configured. - * @retval None - */ -void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef* PeriphClkInit) -{ - uint32_t tempreg; - /* Set all possible values for the extended clock type parameter------------*/ - PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_I2S | RCC_PERIPHCLK_RTC; - /* Get the PLLI2S Clock configuration --------------------------------------*/ - PeriphClkInit->PLLI2S.PLLI2SN = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)); - PeriphClkInit->PLLI2S.PLLI2SR = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR)); -#if defined(STM32F411xE) - PeriphClkInit->PLLI2S.PLLI2SM = (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM); -#endif /* STM32F411xE */ - /* Get the RTC Clock configuration -----------------------------------------*/ - tempreg = (RCC->CFGR & RCC_CFGR_RTCPRE); - PeriphClkInit->RTCClockSelection = (uint32_t)((tempreg) | (RCC->BDCR & RCC_BDCR_RTCSEL)); -#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) - - /* Get the TIM Prescaler configuration -------------------------------------*/ - if ((RCC->DCKCFGR & RCC_DCKCFGR_TIMPRE) == RESET) - { - PeriphClkInit->TIMPresSelection = RCC_TIMPRES_DESACTIVATED; - } - else - { - PeriphClkInit->TIMPresSelection = RCC_TIMPRES_ACTIVATED; - } - -#endif /* STM32F401xC || STM32F401xE || STM32F411xE */ -} -#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F401xC || STM32F401xE || STM32F411xE */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) ||\ - defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -/** - * @brief Initializes the RCC Oscillators according to the specified parameters in the - * RCC_OscInitTypeDef. - * @param RCC_OscInitStruct: pointer to an RCC_OscInitTypeDef structure that - * contains the configuration information for the RCC Oscillators. - * @note The PLL is not disabled when used as system clock. - * @note Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not - * supported by this API. User should request a transition to LSE Off - * first and then LSE On or LSE Bypass. - * @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not - * supported by this API. User should request a transition to HSE Off - * first and then HSE On or HSE Bypass. - * @note This function add the PLL/PLLR factor management during PLL configuration this feature - * is only available in STM32F410xx/STM32F446xx/STM32F469xx/STM32F479xx/STM32F412Zx/STM32F412Vx/STM32F412Rx/STM32F412Cx devices - * @retval HAL status - */ -HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef* RCC_OscInitStruct) -{ - uint32_t tickstart = 0U; - /* Check the parameters */ - assert_param(IS_RCC_OSCILLATORTYPE(RCC_OscInitStruct->OscillatorType)); - - /*------------------------------- HSE Configuration ------------------------*/ - if (((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) - { - /* Check the parameters */ - assert_param(IS_RCC_HSE(RCC_OscInitStruct->HSEState)); - /* When the HSE is used as system clock or clock source for PLL in these cases HSE will not disabled */ -#if defined(STM32F446xx) - - if ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSE) || \ - ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSE)) || \ - ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLLR) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSE))) -#else - if ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSE) || \ - ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSE))) -#endif /* STM32F446xx */ - { - if ((__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) && (RCC_OscInitStruct->HSEState == RCC_HSE_OFF)) - { - return HAL_ERROR; - } - } - else - { - /* Set the new HSE configuration ---------------------------------------*/ - __HAL_RCC_HSE_CONFIG(RCC_OscInitStruct->HSEState); - - /* Check the HSE State */ - if ((RCC_OscInitStruct->HSEState) != RCC_HSE_OFF) - { - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till HSE is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - else - { - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till HSE is bypassed or disabled */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - } - - /*----------------------------- HSI Configuration --------------------------*/ - if (((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) - { - /* Check the parameters */ - assert_param(IS_RCC_HSI(RCC_OscInitStruct->HSIState)); - assert_param(IS_RCC_CALIBRATION_VALUE(RCC_OscInitStruct->HSICalibrationValue)); - /* Check if HSI is used as system clock or as PLL source when PLL is selected as system clock */ -#if defined(STM32F446xx) - - if ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSI) || \ - ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSI)) || \ - ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLLR) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSI))) -#else - if ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSI) || \ - ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSI))) -#endif /* STM32F446xx */ - { - /* When HSI is used as system clock it will not disabled */ - if ((__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) && (RCC_OscInitStruct->HSIState != RCC_HSI_ON)) - { - return HAL_ERROR; - } - /* Otherwise, just the calibration is allowed */ - else - { - /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ - __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); - } - } - else - { - /* Check the HSI State */ - if ((RCC_OscInitStruct->HSIState) != RCC_HSI_OFF) - { - /* Enable the Internal High Speed oscillator (HSI). */ - __HAL_RCC_HSI_ENABLE(); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till HSI is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ - __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); - } - else - { - /* Disable the Internal High Speed oscillator (HSI). */ - __HAL_RCC_HSI_DISABLE(); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till HSI is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - } - - /*------------------------------ LSI Configuration -------------------------*/ - if (((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) - { - /* Check the parameters */ - assert_param(IS_RCC_LSI(RCC_OscInitStruct->LSIState)); - - /* Check the LSI State */ - if ((RCC_OscInitStruct->LSIState) != RCC_LSI_OFF) - { - /* Enable the Internal Low Speed oscillator (LSI). */ - __HAL_RCC_LSI_ENABLE(); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till LSI is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - else - { - /* Disable the Internal Low Speed oscillator (LSI). */ - __HAL_RCC_LSI_DISABLE(); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till LSI is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - - /*------------------------------ LSE Configuration -------------------------*/ - if (((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE) - { - /* Check the parameters */ - assert_param(IS_RCC_LSE(RCC_OscInitStruct->LSEState)); - /* Enable Power Clock*/ - __HAL_RCC_PWR_CLK_ENABLE(); - /* Enable write access to Backup domain */ - PWR->CR |= PWR_CR_DBP; - /* Wait for Backup domain Write protection disable */ - tickstart = HAL_GetTick(); - - while ((PWR->CR & PWR_CR_DBP) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Set the new LSE configuration -----------------------------------------*/ - __HAL_RCC_LSE_CONFIG(RCC_OscInitStruct->LSEState); - - /* Check the LSE State */ - if ((RCC_OscInitStruct->LSEState) != RCC_LSE_OFF) - { - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till LSE is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - else - { - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till LSE is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - - /*-------------------------------- PLL Configuration -----------------------*/ - /* Check the parameters */ - assert_param(IS_RCC_PLL(RCC_OscInitStruct->PLL.PLLState)); - - if ((RCC_OscInitStruct->PLL.PLLState) != RCC_PLL_NONE) - { - /* Check if the PLL is used as system clock or not */ - if (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_PLL) - { - if ((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_ON) - { - /* Check the parameters */ - assert_param(IS_RCC_PLLSOURCE(RCC_OscInitStruct->PLL.PLLSource)); - assert_param(IS_RCC_PLLM_VALUE(RCC_OscInitStruct->PLL.PLLM)); - assert_param(IS_RCC_PLLN_VALUE(RCC_OscInitStruct->PLL.PLLN)); - assert_param(IS_RCC_PLLP_VALUE(RCC_OscInitStruct->PLL.PLLP)); - assert_param(IS_RCC_PLLQ_VALUE(RCC_OscInitStruct->PLL.PLLQ)); - assert_param(IS_RCC_PLLR_VALUE(RCC_OscInitStruct->PLL.PLLR)); - /* Disable the main PLL. */ - __HAL_RCC_PLL_DISABLE(); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till PLL is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - - /* Configure the main PLL clock source, multiplication and division factors. */ - __HAL_RCC_PLL_CONFIG(RCC_OscInitStruct->PLL.PLLSource, - RCC_OscInitStruct->PLL.PLLM, - RCC_OscInitStruct->PLL.PLLN, - RCC_OscInitStruct->PLL.PLLP, - RCC_OscInitStruct->PLL.PLLQ, - RCC_OscInitStruct->PLL.PLLR); - /* Enable the main PLL. */ - __HAL_RCC_PLL_ENABLE(); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till PLL is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) - { - if ((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - else - { - /* Disable the main PLL. */ - __HAL_RCC_PLL_DISABLE(); - /* Get Start Tick*/ - tickstart = HAL_GetTick(); - - /* Wait till PLL is ready */ - while (__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) - { - if ((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) - { - return HAL_TIMEOUT; - } - } - } - } - else - { - return HAL_ERROR; - } - } - - return HAL_OK; -} - -/** - * @brief Configures the RCC_OscInitStruct according to the internal - * RCC configuration registers. - * @param RCC_OscInitStruct: pointer to an RCC_OscInitTypeDef structure that will be configured. - * - * @note This function is only available in case of STM32F410xx/STM32F446xx/STM32F469xx/STM32F479xx/STM32F412Zx/STM32F412Vx/STM32F412Rx/STM32F412Cx devices. - * @note This function add the PLL/PLLR factor management - * @retval None - */ -void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef* RCC_OscInitStruct) -{ - /* Set all possible values for the Oscillator type parameter ---------------*/ - RCC_OscInitStruct->OscillatorType = RCC_OSCILLATORTYPE_HSE | RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_LSE | RCC_OSCILLATORTYPE_LSI; - - /* Get the HSE configuration -----------------------------------------------*/ - if ((RCC->CR & RCC_CR_HSEBYP) == RCC_CR_HSEBYP) - { - RCC_OscInitStruct->HSEState = RCC_HSE_BYPASS; - } - else if ((RCC->CR & RCC_CR_HSEON) == RCC_CR_HSEON) - { - RCC_OscInitStruct->HSEState = RCC_HSE_ON; - } - else - { - RCC_OscInitStruct->HSEState = RCC_HSE_OFF; - } - - /* Get the HSI configuration -----------------------------------------------*/ - if ((RCC->CR & RCC_CR_HSION) == RCC_CR_HSION) - { - RCC_OscInitStruct->HSIState = RCC_HSI_ON; - } - else - { - RCC_OscInitStruct->HSIState = RCC_HSI_OFF; - } - - RCC_OscInitStruct->HSICalibrationValue = (uint32_t)((RCC->CR & RCC_CR_HSITRIM) >> POSITION_VAL(RCC_CR_HSITRIM)); - - /* Get the LSE configuration -----------------------------------------------*/ - if ((RCC->BDCR & RCC_BDCR_LSEBYP) == RCC_BDCR_LSEBYP) - { - RCC_OscInitStruct->LSEState = RCC_LSE_BYPASS; - } - else if ((RCC->BDCR & RCC_BDCR_LSEON) == RCC_BDCR_LSEON) - { - RCC_OscInitStruct->LSEState = RCC_LSE_ON; - } - else - { - RCC_OscInitStruct->LSEState = RCC_LSE_OFF; - } - - /* Get the LSI configuration -----------------------------------------------*/ - if ((RCC->CSR & RCC_CSR_LSION) == RCC_CSR_LSION) - { - RCC_OscInitStruct->LSIState = RCC_LSI_ON; - } - else - { - RCC_OscInitStruct->LSIState = RCC_LSI_OFF; - } - - /* Get the PLL configuration -----------------------------------------------*/ - if ((RCC->CR & RCC_CR_PLLON) == RCC_CR_PLLON) - { - RCC_OscInitStruct->PLL.PLLState = RCC_PLL_ON; - } - else - { - RCC_OscInitStruct->PLL.PLLState = RCC_PLL_OFF; - } - - RCC_OscInitStruct->PLL.PLLSource = (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC); - RCC_OscInitStruct->PLL.PLLM = (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM); - RCC_OscInitStruct->PLL.PLLN = (uint32_t)((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> POSITION_VAL(RCC_PLLCFGR_PLLN)); - RCC_OscInitStruct->PLL.PLLP = (uint32_t)((((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) + RCC_PLLCFGR_PLLP_0) << 1U) >> POSITION_VAL(RCC_PLLCFGR_PLLP)); - RCC_OscInitStruct->PLL.PLLQ = (uint32_t)((RCC->PLLCFGR & RCC_PLLCFGR_PLLQ) >> POSITION_VAL(RCC_PLLCFGR_PLLQ)); - RCC_OscInitStruct->PLL.PLLR = (uint32_t)((RCC->PLLCFGR & RCC_PLLCFGR_PLLR) >> POSITION_VAL(RCC_PLLCFGR_PLLR)); -} -#endif /* STM32F410xx || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) ||\ - defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) -/** - * @brief Select LSE mode - * - * @note This mode is only available for STM32F410xx/STM32F411xx/STM32F446xx/STM32F469xx/STM32F479xx/STM32F412Zx/STM32F412Vx/STM32F412Rx/STM32F412Cx devices. - * - * @param Mode: specifies the LSE mode. - * This parameter can be one of the following values: - * @arg RCC_LSE_LOWPOWER_MODE: LSE oscillator in low power mode selection - * @arg RCC_LSE_HIGHDRIVE_MODE: LSE oscillator in High Drive mode selection - * @retval None - */ -void HAL_RCCEx_SelectLSEMode(uint8_t Mode) -{ - /* Check the parameters */ - assert_param(IS_RCC_LSE_MODE(Mode)); - - if (Mode == RCC_LSE_HIGHDRIVE_MODE) - { - SET_BIT(RCC->BDCR, RCC_BDCR_LSEMOD); - } - else - { - CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEMOD); - } -} - -#endif /* STM32F410xx || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ - -#if defined(STM32F446xx) -/** - * @brief Returns the SYSCLK frequency - * - * @note This function implementation is valid only for STM32F446xx devices. - * @note This function add the PLL/PLLR System clock source - * - * @note The system frequency computed by this function is not the real - * frequency in the chip. It is calculated based on the predefined - * constant and the selected clock source: - * @note If SYSCLK source is HSI, function returns values based on HSI_VALUE(*) - * @note If SYSCLK source is HSE, function returns values based on HSE_VALUE(**) - * @note If SYSCLK source is PLL or PLLR, function returns values based on HSE_VALUE(**) - * or HSI_VALUE(*) multiplied/divided by the PLL factors. - * @note (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value - * 16 MHz) but the real value may vary depending on the variations - * in voltage and temperature. - * @note (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value - * 25 MHz), user has to ensure that HSE_VALUE is same as the real - * frequency of the crystal used. Otherwise, this function may - * have wrong result. - * - * @note The result of this function could be not correct when using fractional - * value for HSE crystal. - * - * @note This function can be used by the user application to compute the - * baudrate for the communication peripherals or configure other parameters. - * - * @note Each time SYSCLK changes, this function must be called to update the - * right SYSCLK value. Otherwise, any configuration based on this function will be incorrect. - * - * - * @retval SYSCLK frequency - */ -uint32_t HAL_RCC_GetSysClockFreq(void) -{ - uint32_t pllm = 0U; - uint32_t pllvco = 0U; - uint32_t pllp = 0U; - uint32_t pllr = 0U; - uint32_t sysclockfreq = 0U; - - /* Get SYSCLK source -------------------------------------------------------*/ - switch (RCC->CFGR & RCC_CFGR_SWS) - { - case RCC_CFGR_SWS_HSI: /* HSI used as system clock source */ - { - sysclockfreq = HSI_VALUE; - break; - } - - case RCC_CFGR_SWS_HSE: /* HSE used as system clock source */ - { - sysclockfreq = HSE_VALUE; - break; - } - - case RCC_CFGR_SWS_PLL: /* PLL/PLLP used as system clock source */ - { - /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLLM) * PLLN - SYSCLK = PLL_VCO / PLLP */ - pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM; - - if (__HAL_RCC_GET_PLL_OSCSOURCE() != RCC_PLLSOURCE_HSI) - { - /* HSE used as PLL clock source */ - pllvco = ((HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> POSITION_VAL(RCC_PLLCFGR_PLLN))); - } - else - { - /* HSI used as PLL clock source */ - pllvco = ((HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> POSITION_VAL(RCC_PLLCFGR_PLLN))); - } - - pllp = ((((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >> POSITION_VAL(RCC_PLLCFGR_PLLP)) + 1U) * 2U); - sysclockfreq = pllvco / pllp; - break; - } - - case RCC_CFGR_SWS_PLLR: /* PLL/PLLR used as system clock source */ - { - /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLLM) * PLLN - SYSCLK = PLL_VCO / PLLR */ - pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM; - - if (__HAL_RCC_GET_PLL_OSCSOURCE() != RCC_PLLSOURCE_HSI) - { - /* HSE used as PLL clock source */ - pllvco = ((HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> POSITION_VAL(RCC_PLLCFGR_PLLN))); - } - else - { - /* HSI used as PLL clock source */ - pllvco = ((HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> POSITION_VAL(RCC_PLLCFGR_PLLN))); - } - - pllr = ((RCC->PLLCFGR & RCC_PLLCFGR_PLLR) >> POSITION_VAL(RCC_PLLCFGR_PLLR)); - sysclockfreq = pllvco / pllr; - break; - } - - default: - { - sysclockfreq = HSI_VALUE; - break; - } - } - - return sysclockfreq; -} -#endif /* STM32F446xx */ - -/** - * @} - */ - -/** - * @} - */ - -#endif /* HAL_RCC_MODULE_ENABLED */ -/** - * @} - */ - -/** - * @} - */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/EpsilonLights.ioc b/EpsilonLights/EpsilonLights.ioc index 18939ff0..918edded 100644 --- a/EpsilonLights/EpsilonLights.ioc +++ b/EpsilonLights/EpsilonLights.ioc @@ -1,80 +1,86 @@ #MicroXplorer Configuration settings - do not modify -CAN2.BS1=CAN_BS1_5TQ -CAN2.BS2=CAN_BS2_4TQ -CAN2.CalculateTimeBit=2000 -CAN2.CalculateTimeQuantum=200.0 -CAN2.IPParameters=CalculateTimeQuantum,CalculateTimeBit,Mode,Prescaler,BS1,BS2 -CAN2.Mode=CAN_MODE_LOOPBACK -CAN2.Prescaler=4 -FREERTOS.IPParameters=Tasks01 -FREERTOS.Tasks01=defaultTask,0,128,StartDefaultTask,Default +CAN.BS1=CAN_BS1_5TQ +CAN.BS2=CAN_BS2_4TQ +CAN.CalculateTimeBit=2000 +CAN.CalculateTimeQuantum=200.0 +CAN.IPParameters=CalculateTimeQuantum,CalculateTimeBit,Prescaler,BS1,BS2,Mode +CAN.Mode=CAN_MODE_LOOPBACK +CAN.Prescaler=2 +FREERTOS.INCLUDE_vTaskDelayUntil=1 +FREERTOS.IPParameters=Tasks01,INCLUDE_vTaskDelayUntil,configUSE_PREEMPTION +FREERTOS.Tasks01=defaultTask,0,128,StartDefaultTask,Default,NULL +FREERTOS.configUSE_PREEMPTION=0 File.Version=6 -KeepUserPlacement=true -Mcu.Family=STM32F4 -Mcu.IP0=CAN2 +KeepUserPlacement=false +Mcu.Family=STM32F1 +Mcu.IP0=CAN Mcu.IP1=FREERTOS Mcu.IP2=NVIC Mcu.IP3=RCC Mcu.IP4=SYS Mcu.IPNb=5 -Mcu.Name=STM32F407V(E-G)Tx -Mcu.Package=LQFP100 -Mcu.Pin0=PH0-OSC_IN -Mcu.Pin1=PH1-OSC_OUT -Mcu.Pin10=PA13 -Mcu.Pin11=PA14 -Mcu.Pin12=PD0 -Mcu.Pin13=PD1 -Mcu.Pin14=PD2 -Mcu.Pin15=PD3 -Mcu.Pin16=PD4 -Mcu.Pin17=PD5 -Mcu.Pin18=PB3 -Mcu.Pin19=PE1 -Mcu.Pin2=PC0 -Mcu.Pin20=VP_FREERTOS_VS_ENABLE -Mcu.Pin21=VP_SYS_VS_tim2 -Mcu.Pin3=PA0-WKUP -Mcu.Pin4=PA5 -Mcu.Pin5=PA6 -Mcu.Pin6=PA7 -Mcu.Pin7=PB2 -Mcu.Pin8=PB12 -Mcu.Pin9=PB13 -Mcu.PinsNb=22 +Mcu.Name=STM32F103C(4-6)Tx +Mcu.Package=LQFP48 +Mcu.Pin0=PD0-OSC_IN +Mcu.Pin1=PD1-OSC_OUT +Mcu.Pin10=PA11 +Mcu.Pin11=PA12 +Mcu.Pin12=PA13 +Mcu.Pin13=PA14 +Mcu.Pin14=PA15 +Mcu.Pin15=PB3 +Mcu.Pin16=VP_FREERTOS_VS_CMSIS_V1 +Mcu.Pin17=VP_SYS_VS_tim2 +Mcu.Pin2=PA5 +Mcu.Pin3=PA6 +Mcu.Pin4=PA7 +Mcu.Pin5=PB10 +Mcu.Pin6=PB11 +Mcu.Pin7=PB12 +Mcu.Pin8=PB13 +Mcu.Pin9=PB14 +Mcu.PinsNb=18 +Mcu.ThirdPartyNb=0 Mcu.UserConstants= -Mcu.UserName=STM32F407VGTx -MxCube.Version=4.15.0 -MxDb.Version=DB.4.0.150 -NVIC.BusFault_IRQn=true\:0\:0\:false\:false\:false\:false -NVIC.CAN2_RX0_IRQn=true\:0\:0\:false\:false\:true\:false -NVIC.CAN2_TX_IRQn=true\:0\:0\:false\:false\:true\:false -NVIC.DebugMonitor_IRQn=true\:0\:0\:false\:false\:false\:false -NVIC.HardFault_IRQn=true\:0\:0\:false\:false\:false\:false -NVIC.MemoryManagement_IRQn=true\:0\:0\:false\:false\:false\:false -NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:false\:false -NVIC.PendSV_IRQn=true\:15\:0\:false\:false\:false\:true +Mcu.UserName=STM32F103C4Tx +MxCube.Version=5.3.0 +MxDb.Version=DB.5.0.30 +NVIC.BusFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false +NVIC.DebugMonitor_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false +NVIC.HardFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false +NVIC.MemoryManagement_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false +NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false +NVIC.PendSV_IRQn=true\:15\:0\:false\:false\:false\:true\:false\:false NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4 -NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:false\:false -NVIC.SysTick_IRQn=true\:15\:0\:false\:false\:true\:true -NVIC.TIM2_IRQn=true\:0\:0\:false\:false\:true\:false +NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:false\:false\:false\:false +NVIC.SysTick_IRQn=true\:15\:0\:false\:false\:false\:true\:false\:true +NVIC.TIM2_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:true NVIC.TimeBase=TIM2_IRQn NVIC.TimeBaseIP=TIM2 -NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:false\:false -PA0-WKUP.GPIOParameters=GPIO_Label,GPIO_ModeDefaultEXTI,GPIO_PuPd -PA0-WKUP.GPIO_Label=B1 [Blue PushButton] -PA0-WKUP.GPIO_ModeDefaultEXTI=GPIO_MODE_EVT_RISING -PA0-WKUP.GPIO_PuPd=GPIO_NOPULL -PA0-WKUP.Locked=true -PA0-WKUP.Signal=GPXTI0 +NVIC.USB_HP_CAN1_TX_IRQn=true\:5\:0\:false\:false\:true\:true\:true\:true +NVIC.USB_LP_CAN1_RX0_IRQn=true\:5\:0\:false\:false\:true\:true\:true\:true +NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false +PA11.Locked=true +PA11.Mode=Master +PA11.Signal=CAN_RX +PA12.Locked=true +PA12.Mode=Master +PA12.Signal=CAN_TX PA13.GPIOParameters=GPIO_Label PA13.GPIO_Label=SWDIO PA13.Locked=true +PA13.Mode=JTAG_4_pins PA13.Signal=SYS_JTMS-SWDIO PA14.GPIOParameters=GPIO_Label PA14.GPIO_Label=SWCLK PA14.Locked=true +PA14.Mode=JTAG_4_pins PA14.Signal=SYS_JTCK-SWCLK +PA15.GPIOParameters=GPIO_Label +PA15.GPIO_Label=JTDI +PA15.Locked=true +PA15.Mode=JTAG_4_pins +PA15.Signal=SYS_JTDI PA5.GPIOParameters=GPIO_Label PA5.GPIO_Label=LED_RED PA5.Locked=true @@ -87,139 +93,100 @@ PA7.GPIOParameters=GPIO_Label PA7.GPIO_Label=LED_BLUE PA7.Locked=true PA7.Signal=GPIO_Output -PB12.Mode=Slave -PB12.Signal=CAN2_RX -PB13.Mode=Slave -PB13.Signal=CAN2_TX -PB2.GPIOParameters=GPIO_Label,GPIO_PuPd,GPIO_Mode -PB2.GPIO_Label=BOOT1 -PB2.GPIO_Mode=GPIO_MODE_INPUT -PB2.GPIO_PuPd=GPIO_NOPULL -PB2.Locked=true -PB2.Signal=GPIO_Input +PB10.GPIOParameters=GPIO_Label +PB10.GPIO_Label=RSIGNAL +PB10.Locked=true +PB10.Signal=GPIO_Output +PB11.GPIOParameters=GPIO_Label +PB11.GPIO_Label=LSIGNAL +PB11.Locked=true +PB11.Signal=GPIO_Output +PB12.GPIOParameters=GPIO_Label +PB12.GPIO_Label=BRAKE +PB12.Locked=true +PB12.Signal=GPIO_Output +PB13.GPIOParameters=GPIO_Label +PB13.GPIO_Label=HEAD +PB13.Locked=true +PB13.Signal=GPIO_Output +PB14.GPIOParameters=GPIO_Label +PB14.GPIO_Label=STROBE +PB14.Locked=true +PB14.Signal=GPIO_Output PB3.GPIOParameters=GPIO_Label PB3.GPIO_Label=SWO PB3.Locked=true -PB3.Signal=SYS_JTDO-SWO -PC0.GPIOParameters=GPIO_Label,GPIO_Speed,GPIO_PuPd -PC0.GPIO_Label=OTG_FS_PowerSwitchOn -PC0.GPIO_PuPd=GPIO_NOPULL -PC0.GPIO_Speed=GPIO_SPEED_FREQ_LOW -PC0.Locked=true -PC0.Signal=GPIO_Output +PB3.Mode=JTAG_4_pins +PB3.Signal=SYS_JTDO-TRACESWO PCC.Checker=false -PCC.Line=STM32F407/417 -PCC.MCU=STM32F407V(E-G)Tx -PCC.MXVersion=4.15.0 -PCC.PartNumber=STM32F407VGTx +PCC.Line=STM32F103 +PCC.MCU=STM32F103C(4-6)Tx +PCC.PartNumber=STM32F103C4Tx PCC.Seq0=0 -PCC.Series=STM32F4 +PCC.Series=STM32F1 PCC.Temperature=25 PCC.Vdd=3.3 -PD0.GPIOParameters=GPIO_Label -PD0.GPIO_Label=RSIGNAL -PD0.Locked=true -PD0.Signal=GPIO_Output -PD1.GPIOParameters=GPIO_Label -PD1.GPIO_Label=LSIGNAL -PD1.Locked=true -PD1.Signal=GPIO_Output -PD2.GPIOParameters=GPIO_Label -PD2.GPIO_Label=BRAKE -PD2.Locked=true -PD2.Signal=GPIO_Output -PD3.GPIOParameters=GPIO_Label -PD3.GPIO_Label=HHIGH -PD3.Locked=true -PD3.Signal=GPIO_Output -PD4.GPIOParameters=GPIO_Label -PD4.GPIO_Label=HLOW -PD4.Locked=true -PD4.Signal=GPIO_Output -PD5.GPIOParameters=GPIO_Label -PD5.GPIO_Label=ESTROBE -PD5.Locked=true -PD5.Signal=GPIO_Output -PE1.GPIOParameters=GPIO_Label,GPIO_ModeDefaultEXTI,GPIO_PuPd -PE1.GPIO_Label=MEMS_INT2 [LIS302DL_INT2] -PE1.GPIO_ModeDefaultEXTI=GPIO_MODE_EVT_RISING -PE1.GPIO_PuPd=GPIO_NOPULL -PE1.Locked=true -PE1.Signal=GPXTI1 -PH0-OSC_IN.GPIOParameters=GPIO_Label -PH0-OSC_IN.GPIO_Label=PH0-OSC_IN -PH0-OSC_IN.Locked=true -PH0-OSC_IN.Mode=HSE-External-Oscillator -PH0-OSC_IN.Signal=RCC_OSC_IN -PH1-OSC_OUT.GPIOParameters=GPIO_Label -PH1-OSC_OUT.GPIO_Label=PH1-OSC_OUT -PH1-OSC_OUT.Locked=true -PH1-OSC_OUT.Mode=HSE-External-Oscillator -PH1-OSC_OUT.Signal=RCC_OSC_OUT +PD0-OSC_IN.GPIOParameters=GPIO_Label +PD0-OSC_IN.GPIO_Label=CLK_IN +PD0-OSC_IN.Mode=HSE-External-Oscillator +PD0-OSC_IN.Signal=RCC_OSC_IN +PD1-OSC_OUT.GPIOParameters=GPIO_Label +PD1-OSC_OUT.GPIO_Label=CLK_OUT +PD1-OSC_OUT.Mode=HSE-External-Oscillator +PD1-OSC_OUT.Signal=RCC_OSC_OUT +PinOutPanel.RotationAngle=0 ProjectManager.AskForMigrate=true ProjectManager.BackupPrevious=false -ProjectManager.CompilerOptimize=2 +ProjectManager.CompilerOptimize=6 ProjectManager.ComputerToolchain=false ProjectManager.CoupleFile=false +ProjectManager.CustomerFirmwarePackage= +ProjectManager.DefaultFWLocation=true ProjectManager.DeletePrevious=true -ProjectManager.DeviceId=STM32F407VGTx -ProjectManager.FirmwarePackage=STM32Cube FW_F4 V1.12.0 +ProjectManager.DeviceId=STM32F103C4Tx +ProjectManager.FirmwarePackage=STM32Cube FW_F1 V1.8.0 ProjectManager.FreePins=false ProjectManager.HalAssertFull=false ProjectManager.HeapSize=0x200 ProjectManager.KeepUserCode=true ProjectManager.LastFirmware=true ProjectManager.LibraryCopy=1 -ProjectManager.PreviousToolchain=SW4STM32 +ProjectManager.MainLocation=Core/Src +ProjectManager.NoMain=false +ProjectManager.PreviousToolchain= ProjectManager.ProjectBuild=false ProjectManager.ProjectFileName=EpsilonLights.ioc ProjectManager.ProjectName=EpsilonLights ProjectManager.StackSize=0x400 -ProjectManager.TargetToolchain=SW4STM32 -ProjectManager.ToolChainLocation=/home/enoch/ext/SolarCar/Epsilon-Embedded-Software/EpsilonLights -ProjectManager.UnderRoot=true -ProjectManager.functionlistsort=1-MX_GPIO_Init-GPIO-false,2-MX_CAN2_Init-CAN2-false -RCC.48MHZClocksFreq_Value=45714285.71428572 -RCC.AHBFreq_Value=160000000 -RCC.APB1CLKDivider=RCC_HCLK_DIV8 -RCC.APB1Freq_Value=20000000 -RCC.APB1TimFreq_Value=40000000 -RCC.APB2CLKDivider=RCC_HCLK_DIV4 -RCC.APB2Freq_Value=40000000 -RCC.APB2TimFreq_Value=80000000 -RCC.CortexFreq_Value=160000000 -RCC.EthernetFreq_Value=160000000 -RCC.FCLKCortexFreq_Value=160000000 +ProjectManager.TargetToolchain=Makefile +ProjectManager.ToolChainLocation= +ProjectManager.UnderRoot=false +ProjectManager.functionlistsort=1-MX_GPIO_Init-GPIO-false-HAL-true,2-SystemClock_Config-RCC-false-HAL-false,3-MX_CAN_Init-CAN-false-HAL-true +RCC.ADCFreqValue=2500000 +RCC.AHBCLKDivider=RCC_SYSCLK_DIV2 +RCC.AHBFreq_Value=10000000 +RCC.APB1Freq_Value=10000000 +RCC.APB1TimFreq_Value=10000000 +RCC.APB2CLKDivider=RCC_HCLK_DIV2 +RCC.APB2Freq_Value=5000000 +RCC.APB2TimFreq_Value=10000000 +RCC.FCLKCortexFreq_Value=10000000 RCC.FamilyName=M -RCC.HCLKFreq_Value=160000000 -RCC.HSE_VALUE=8000000 -RCC.HSI_VALUE=16000000 -RCC.I2SClocksFreq_Value=96000000 -RCC.IPParameters=48MHZClocksFreq_Value,AHBFreq_Value,APB1CLKDivider,APB1Freq_Value,APB1TimFreq_Value,APB2CLKDivider,APB2Freq_Value,APB2TimFreq_Value,CortexFreq_Value,EthernetFreq_Value,FCLKCortexFreq_Value,FamilyName,HCLKFreq_Value,HSE_VALUE,HSI_VALUE,I2SClocksFreq_Value,LSE_VALUE,LSI_VALUE,MCO2PinFreq_Value,PLLCLKFreq_Value,PLLM,PLLN,PLLQ,PLLQCLKFreq_Value,PLLSourceVirtual,RTCFreq_Value,RTCHSEDivFreq_Value,SYSCLKFreq_VALUE,SYSCLKSource,VCOI2SOutputFreq_Value,VCOInputFreq_Value,VCOOutputFreq_Value,VcooutputI2S -RCC.LSE_VALUE=32768 -RCC.LSI_VALUE=32000 -RCC.MCO2PinFreq_Value=160000000 -RCC.PLLCLKFreq_Value=160000000 -RCC.PLLM=8 -RCC.PLLN=320 -RCC.PLLQ=7 -RCC.PLLQCLKFreq_Value=45714285.71428572 +RCC.HCLKFreq_Value=10000000 +RCC.HSEDivPLL=RCC_HSE_PREDIV_DIV2 +RCC.IPParameters=ADCFreqValue,AHBCLKDivider,AHBFreq_Value,APB1Freq_Value,APB1TimFreq_Value,APB2CLKDivider,APB2Freq_Value,APB2TimFreq_Value,FCLKCortexFreq_Value,FamilyName,HCLKFreq_Value,HSEDivPLL,MCOFreq_Value,PLLCLKFreq_Value,PLLMCOFreq_Value,PLLMUL,PLLSourceVirtual,SYSCLKFreq_VALUE,SYSCLKSource,TimSysFreq_Value,USBFreq_Value,VCOOutput2Freq_Value +RCC.MCOFreq_Value=20000000 +RCC.PLLCLKFreq_Value=20000000 +RCC.PLLMCOFreq_Value=10000000 +RCC.PLLMUL=RCC_PLL_MUL5 RCC.PLLSourceVirtual=RCC_PLLSOURCE_HSE -RCC.RTCFreq_Value=32000 -RCC.RTCHSEDivFreq_Value=4000000 -RCC.SYSCLKFreq_VALUE=160000000 +RCC.SYSCLKFreq_VALUE=20000000 RCC.SYSCLKSource=RCC_SYSCLKSOURCE_PLLCLK -RCC.VCOI2SOutputFreq_Value=192000000 -RCC.VCOInputFreq_Value=1000000 -RCC.VCOOutputFreq_Value=320000000 -RCC.VcooutputI2S=96000000 -SH.GPXTI0.0=GPIO_EXTI0 -SH.GPXTI0.ConfNb=1 -SH.GPXTI1.0=GPIO_EXTI1 -SH.GPXTI1.ConfNb=1 -VP_FREERTOS_VS_ENABLE.Mode=Enabled -VP_FREERTOS_VS_ENABLE.Signal=FREERTOS_VS_ENABLE +RCC.TimSysFreq_Value=10000000 +RCC.USBFreq_Value=20000000 +RCC.VCOOutput2Freq_Value=4000000 +VP_FREERTOS_VS_CMSIS_V1.Mode=CMSIS_V1 +VP_FREERTOS_VS_CMSIS_V1.Signal=FREERTOS_VS_CMSIS_V1 VP_SYS_VS_tim2.Mode=TIM2 VP_SYS_VS_tim2.Signal=SYS_VS_tim2 -board=STM32F4DISCOVERY -boardIOC=true +board=custom diff --git a/EpsilonLights/Inc/FreeRTOSConfig.h b/EpsilonLights/Inc/FreeRTOSConfig.h deleted file mode 100644 index 9d8dc704..00000000 --- a/EpsilonLights/Inc/FreeRTOSConfig.h +++ /dev/null @@ -1,169 +0,0 @@ -/* - FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd. - All rights reserved - - VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION. - - This file is part of the FreeRTOS distribution. - - FreeRTOS is free software; you can redistribute it and/or modify it under - the terms of the GNU General Public License (version 2) as published by the - Free Software Foundation >>!AND MODIFIED BY!<< the FreeRTOS exception. - - *************************************************************************** - >>! NOTE: The modification to the GPL is included to allow you to !<< - >>! distribute a combined work that includes FreeRTOS without being !<< - >>! obliged to provide the source code for proprietary components !<< - >>! outside of the FreeRTOS kernel. !<< - *************************************************************************** - - FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY - WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS - FOR A PARTICULAR PURPOSE. Full license text is available on the following - link: http://www.freertos.org/a00114.html - - *************************************************************************** - * * - * FreeRTOS provides completely free yet professionally developed, * - * robust, strictly quality controlled, supported, and cross * - * platform software that is more than just the market leader, it * - * is the industry's de facto standard. * - * * - * Help yourself get started quickly while simultaneously helping * - * to support the FreeRTOS project by purchasing a FreeRTOS * - * tutorial book, reference manual, or both: * - * http://www.FreeRTOS.org/Documentation * - * * - *************************************************************************** - - http://www.FreeRTOS.org/FAQHelp.html - Having a problem? Start by reading - the FAQ page "My application does not run, what could be wrong?". Have you - defined configASSERT()? - - http://www.FreeRTOS.org/support - In return for receiving this top quality - embedded software for free we request you assist our global community by - participating in the support forum. - - http://www.FreeRTOS.org/training - Investing in training allows your team to - be as productive as possible as early as possible. Now you can receive - FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers - Ltd, and the world's leading authority on the world's leading RTOS. - - http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products, - including FreeRTOS+Trace - an indispensable productivity tool, a DOS - compatible FAT file system, and our tiny thread aware UDP/IP stack. - - http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate. - Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS. - - http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High - Integrity Systems ltd. to sell under the OpenRTOS brand. Low cost OpenRTOS - licenses offer ticketed support, indemnification and commercial middleware. - - http://www.SafeRTOS.com - High Integrity Systems also provide a safety - engineered and independently SIL3 certified version for use in safety and - mission critical applications that require provable dependability. - - 1 tab == 4 spaces! -*/ - -#ifndef FREERTOS_CONFIG_H -#define FREERTOS_CONFIG_H - -/*----------------------------------------------------------- - * Application specific definitions. - * - * These definitions should be adjusted for your particular hardware and - * application requirements. - * - * THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE - * FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE. - * - * See http://www.freertos.org/a00110.html. - *----------------------------------------------------------*/ - -/* USER CODE BEGIN Includes */ -/* Section where include file can be added */ -/* USER CODE END Includes */ - -/* Ensure stdint is only used by the compiler, and not the assembler. */ -#if defined(__ICCARM__) || defined(__CC_ARM) || defined(__GNUC__) -#include -#include "mxconstants.h" -extern uint32_t SystemCoreClock; -#endif - -#define configUSE_PREEMPTION 1 -#define configUSE_IDLE_HOOK 0 -#define configUSE_TICK_HOOK 0 -#define configCPU_CLOCK_HZ ( SystemCoreClock ) -#define configTICK_RATE_HZ ((TickType_t)1000) -#define configMAX_PRIORITIES ( 7 ) -#define configMINIMAL_STACK_SIZE ((uint16_t)128) -#define configTOTAL_HEAP_SIZE ((size_t)15360) -#define configMAX_TASK_NAME_LEN ( 16 ) -#define configUSE_TRACE_FACILITY 1 -#define configUSE_16_BIT_TICKS 0 -#define configUSE_MUTEXES 1 -#define configQUEUE_REGISTRY_SIZE 8 - -/* Co-routine definitions. */ -#define configUSE_CO_ROUTINES 0 -#define configMAX_CO_ROUTINE_PRIORITIES ( 2 ) - -/* Set the following definitions to 1 to include the API function, or zero -to exclude the API function. */ -#define INCLUDE_vTaskPrioritySet 1 -#define INCLUDE_uxTaskPriorityGet 1 -#define INCLUDE_vTaskDelete 1 -#define INCLUDE_vTaskCleanUpResources 0 -#define INCLUDE_vTaskSuspend 1 -#define INCLUDE_vTaskDelayUntil 1 -#define INCLUDE_vTaskDelay 1 -#define INCLUDE_xTaskGetSchedulerState 1 - -/* Cortex-M specific definitions. */ -#ifdef __NVIC_PRIO_BITS -/* __BVIC_PRIO_BITS will be specified when CMSIS is being used. */ -#define configPRIO_BITS __NVIC_PRIO_BITS -#else -#define configPRIO_BITS 4 -#endif - -/* The lowest interrupt priority that can be used in a call to a "set priority" -function. */ -#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY 15 - -/* The highest interrupt priority that can be used by any interrupt service -routine that makes calls to interrupt safe FreeRTOS API functions. DO NOT CALL -INTERRUPT SAFE FREERTOS API FUNCTIONS FROM ANY INTERRUPT THAT HAS A HIGHER -PRIORITY THAN THIS! (higher priorities are lower numeric values. */ -#define configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY 5 - -/* Interrupt priorities used by the kernel port layer itself. These are generic -to all Cortex-M ports, and do not rely on any particular library functions. */ -#define configKERNEL_INTERRUPT_PRIORITY ( configLIBRARY_LOWEST_INTERRUPT_PRIORITY << (8 - configPRIO_BITS) ) -/* !!!! configMAX_SYSCALL_INTERRUPT_PRIORITY must not be set to zero !!!! -See http://www.FreeRTOS.org/RTOS-Cortex-M3-M4.html. */ -#define configMAX_SYSCALL_INTERRUPT_PRIORITY ( configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY << (8 - configPRIO_BITS) ) - -/* Normal assert() semantics without relying on the provision of an assert.h -header file. */ -/* USER CODE BEGIN 1 */ -#define configASSERT( x ) if ((x) == 0) {taskDISABLE_INTERRUPTS(); for( ;; );} -/* USER CODE END 1 */ - -/* Definitions that map the FreeRTOS port interrupt handlers to their CMSIS -standard names. */ -#define vPortSVCHandler SVC_Handler -#define xPortPendSVHandler PendSV_Handler - -/* IMPORTANT: This define MUST be commented when used with STM32Cube firmware, - to prevent overwriting SysTick_Handler defined within STM32Cube HAL */ -/* #define xPortSysTickHandler SysTick_Handler */ - -/* USER CODE BEGIN Defines */ -/* Section where parameter definitions can be added (for instance, to override default ones in FreeRTOS.h) */ -/* USER CODE END Defines */ - -#endif /* FREERTOS_CONFIG_H */ diff --git a/EpsilonLights/Inc/mxconstants.h b/EpsilonLights/Inc/mxconstants.h deleted file mode 100644 index d7535afa..00000000 --- a/EpsilonLights/Inc/mxconstants.h +++ /dev/null @@ -1,93 +0,0 @@ -/** - ****************************************************************************** - * File Name : mxconstants.h - * Description : This file contains the common defines of the application - ****************************************************************************** - * - * COPYRIGHT(c) 2016 STMicroelectronics - * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __MXCONSTANT_H -#define __MXCONSTANT_H -/* Includes ------------------------------------------------------------------*/ - -/* USER CODE BEGIN Includes */ - -/* USER CODE END Includes */ - -/* Private define ------------------------------------------------------------*/ - -#define PH0_OSC_IN_Pin GPIO_PIN_0 -#define PH0_OSC_IN_GPIO_Port GPIOH -#define PH1_OSC_OUT_Pin GPIO_PIN_1 -#define PH1_OSC_OUT_GPIO_Port GPIOH -#define OTG_FS_PowerSwitchOn_Pin GPIO_PIN_0 -#define OTG_FS_PowerSwitchOn_GPIO_Port GPIOC -#define B1_Pin GPIO_PIN_0 -#define B1_GPIO_Port GPIOA -#define LED_RED_Pin GPIO_PIN_5 -#define LED_RED_GPIO_Port GPIOA -#define LED_GREEN_Pin GPIO_PIN_6 -#define LED_GREEN_GPIO_Port GPIOA -#define LED_BLUE_Pin GPIO_PIN_7 -#define LED_BLUE_GPIO_Port GPIOA -#define BOOT1_Pin GPIO_PIN_2 -#define BOOT1_GPIO_Port GPIOB -#define SWDIO_Pin GPIO_PIN_13 -#define SWDIO_GPIO_Port GPIOA -#define SWCLK_Pin GPIO_PIN_14 -#define SWCLK_GPIO_Port GPIOA -#define RSIGNAL_Pin GPIO_PIN_0 -#define RSIGNAL_GPIO_Port GPIOD -#define LSIGNAL_Pin GPIO_PIN_1 -#define LSIGNAL_GPIO_Port GPIOD -#define BRAKE_Pin GPIO_PIN_2 -#define BRAKE_GPIO_Port GPIOD -#define HHIGH_Pin GPIO_PIN_3 -#define HHIGH_GPIO_Port GPIOD -#define HLOW_Pin GPIO_PIN_4 -#define HLOW_GPIO_Port GPIOD -#define ESTROBE_Pin GPIO_PIN_5 -#define ESTROBE_GPIO_Port GPIOD -#define SWO_Pin GPIO_PIN_3 -#define SWO_GPIO_Port GPIOB -#define MEMS_INT2_Pin GPIO_PIN_1 -#define MEMS_INT2_GPIO_Port GPIOE -/* USER CODE BEGIN Private defines */ - -/* USER CODE END Private defines */ - -/** - * @} - */ - -/** - * @} -*/ - -#endif /* __MXCONSTANT_H */ -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Inc/stm32f4xx_hal_conf.h b/EpsilonLights/Inc/stm32f4xx_hal_conf.h deleted file mode 100644 index f00da465..00000000 --- a/EpsilonLights/Inc/stm32f4xx_hal_conf.h +++ /dev/null @@ -1,452 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_conf.h - * @brief HAL configuration file. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2016 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_CONF_H -#define __STM32F4xx_HAL_CONF_H - -#ifdef __cplusplus -extern "C" { -#endif - -#include "mxconstants.h" - -/* Exported types ------------------------------------------------------------*/ -/* Exported constants --------------------------------------------------------*/ - -/* ########################## Module Selection ############################## */ -/** - * @brief This is the list of modules to be used in the HAL driver - */ -#define HAL_MODULE_ENABLED - -/* #define HAL_ADC_MODULE_ENABLED */ -#define HAL_CAN_MODULE_ENABLED -/* #define HAL_CRC_MODULE_ENABLED */ -/* #define HAL_CRYP_MODULE_ENABLED */ -/* #define HAL_DAC_MODULE_ENABLED */ -/* #define HAL_DCMI_MODULE_ENABLED */ -/* #define HAL_DMA2D_MODULE_ENABLED */ -/* #define HAL_ETH_MODULE_ENABLED */ -/* #define HAL_NAND_MODULE_ENABLED */ -/* #define HAL_NOR_MODULE_ENABLED */ -/* #define HAL_PCCARD_MODULE_ENABLED */ -/* #define HAL_SRAM_MODULE_ENABLED */ -/* #define HAL_SDRAM_MODULE_ENABLED */ -/* #define HAL_HASH_MODULE_ENABLED */ -/* #define HAL_I2C_MODULE_ENABLED */ -/* #define HAL_I2S_MODULE_ENABLED */ -/* #define HAL_IWDG_MODULE_ENABLED */ -/* #define HAL_LTDC_MODULE_ENABLED */ -/* #define HAL_RNG_MODULE_ENABLED */ -/* #define HAL_RTC_MODULE_ENABLED */ -/* #define HAL_SAI_MODULE_ENABLED */ -/* #define HAL_SD_MODULE_ENABLED */ -/* #define HAL_SPI_MODULE_ENABLED */ -#define HAL_TIM_MODULE_ENABLED -/* #define HAL_UART_MODULE_ENABLED */ -/* #define HAL_USART_MODULE_ENABLED */ -/* #define HAL_IRDA_MODULE_ENABLED */ -/* #define HAL_SMARTCARD_MODULE_ENABLED */ -/* #define HAL_WWDG_MODULE_ENABLED */ -/* #define HAL_PCD_MODULE_ENABLED */ -/* #define HAL_HCD_MODULE_ENABLED */ -/* #define HAL_DSI_MODULE_ENABLED */ -/* #define HAL_QSPI_MODULE_ENABLED */ -/* #define HAL_QSPI_MODULE_ENABLED */ -/* #define HAL_CEC_MODULE_ENABLED */ -/* #define HAL_FMPI2C_MODULE_ENABLED */ -/* #define HAL_SPDIFRX_MODULE_ENABLED */ -/* #define HAL_DFSDM_MODULE_ENABLED */ -/* #define HAL_LPTIM_MODULE_ENABLED */ -#define HAL_GPIO_MODULE_ENABLED -#define HAL_DMA_MODULE_ENABLED -#define HAL_RCC_MODULE_ENABLED -#define HAL_FLASH_MODULE_ENABLED -#define HAL_PWR_MODULE_ENABLED -#define HAL_CORTEX_MODULE_ENABLED - -/* ########################## HSE/HSI Values adaptation ##################### */ -/** - * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. - * This value is used by the RCC HAL module to compute the system frequency - * (when HSE is used as system clock source, directly or through the PLL). - */ -#if !defined (HSE_VALUE) -#define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */ -#endif /* HSE_VALUE */ - -#if !defined (HSE_STARTUP_TIMEOUT) -#define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */ -#endif /* HSE_STARTUP_TIMEOUT */ - -/** - * @brief Internal High Speed oscillator (HSI) value. - * This value is used by the RCC HAL module to compute the system frequency - * (when HSI is used as system clock source, directly or through the PLL). - */ -#if !defined (HSI_VALUE) -#define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/ -#endif /* HSI_VALUE */ - -/** - * @brief Internal Low Speed oscillator (LSI) value. - */ -#if !defined (LSI_VALUE) -#define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/ -#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz -The real value may vary depending on the variations -in voltage and temperature.*/ -/** - * @brief External Low Speed oscillator (LSE) value. - */ -#if !defined (LSE_VALUE) -#define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */ -#endif /* LSE_VALUE */ - -#if !defined (LSE_STARTUP_TIMEOUT) -#define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */ -#endif /* LSE_STARTUP_TIMEOUT */ - -/** - * @brief External clock source for I2S peripheral - * This value is used by the I2S HAL module to compute the I2S clock source - * frequency, this source is inserted directly through I2S_CKIN pad. - */ -#if !defined (EXTERNAL_CLOCK_VALUE) -#define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the External audio frequency in Hz*/ -#endif /* EXTERNAL_CLOCK_VALUE */ - -/* Tip: To avoid modifying this file each time you need to use different HSE, - === you can define the HSE value in your toolchain compiler preprocessor. */ - -/* ########################### System Configuration ######################### */ -/** - * @brief This is the HAL system configuration section - */ -#define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */ -#define TICK_INT_PRIORITY ((uint32_t)0U) /*!< tick interrupt priority */ -#define USE_RTOS 0U -#define PREFETCH_ENABLE 1U -#define INSTRUCTION_CACHE_ENABLE 1U -#define DATA_CACHE_ENABLE 1U - -/* ########################## Assert Selection ############################## */ -/** - * @brief Uncomment the line below to expanse the "assert_param" macro in the - * HAL drivers code - */ -/* #define USE_FULL_ASSERT 1U */ - -/* ################## Ethernet peripheral configuration ##################### */ - -/* Section 1 : Ethernet peripheral configuration */ - -/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ -#define MAC_ADDR0 2U -#define MAC_ADDR1 0U -#define MAC_ADDR2 0U -#define MAC_ADDR3 0U -#define MAC_ADDR4 0U -#define MAC_ADDR5 0U - -/* Definition of the Ethernet driver buffers size and count */ -#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ -#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ -#define ETH_RXBUFNB ((uint32_t)4U) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ -#define ETH_TXBUFNB ((uint32_t)4U) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ - -/* Section 2: PHY configuration section */ - -/* DP83848_PHY_ADDRESS Address*/ -#define DP83848_PHY_ADDRESS 0x01U -/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ -#define PHY_RESET_DELAY ((uint32_t)0x000000FFU) -/* PHY Configuration delay */ -#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFFU) - -#define PHY_READ_TO ((uint32_t)0x0000FFFFU) -#define PHY_WRITE_TO ((uint32_t)0x0000FFFFU) - -/* Section 3: Common PHY Registers */ - -#define PHY_BCR ((uint16_t)0x0000U) /*!< Transceiver Basic Control Register */ -#define PHY_BSR ((uint16_t)0x0001U) /*!< Transceiver Basic Status Register */ - -#define PHY_RESET ((uint16_t)0x8000U) /*!< PHY Reset */ -#define PHY_LOOPBACK ((uint16_t)0x4000U) /*!< Select loop-back mode */ -#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100U) /*!< Set the full-duplex mode at 100 Mb/s */ -#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000U) /*!< Set the half-duplex mode at 100 Mb/s */ -#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100U) /*!< Set the full-duplex mode at 10 Mb/s */ -#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000U) /*!< Set the half-duplex mode at 10 Mb/s */ -#define PHY_AUTONEGOTIATION ((uint16_t)0x1000U) /*!< Enable auto-negotiation function */ -#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200U) /*!< Restart auto-negotiation function */ -#define PHY_POWERDOWN ((uint16_t)0x0800U) /*!< Select the power down mode */ -#define PHY_ISOLATE ((uint16_t)0x0400U) /*!< Isolate PHY from MII */ - -#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020U) /*!< Auto-Negotiation process completed */ -#define PHY_LINKED_STATUS ((uint16_t)0x0004U) /*!< Valid link established */ -#define PHY_JABBER_DETECTION ((uint16_t)0x0002U) /*!< Jabber condition detected */ - -/* Section 4: Extended PHY Registers */ - -#define PHY_SR ((uint16_t)0x0010U) /*!< PHY status register Offset */ -#define PHY_MICR ((uint16_t)0x0011U) /*!< MII Interrupt Control Register */ -#define PHY_MISR ((uint16_t)0x0012U) /*!< MII Interrupt Status and Misc. Control Register */ - -#define PHY_LINK_STATUS ((uint16_t)0x0001U) /*!< PHY Link mask */ -#define PHY_SPEED_STATUS ((uint16_t)0x0002U) /*!< PHY Speed mask */ -#define PHY_DUPLEX_STATUS ((uint16_t)0x0004U) /*!< PHY Duplex mask */ - -#define PHY_MICR_INT_EN ((uint16_t)0x0002U) /*!< PHY Enable interrupts */ -#define PHY_MICR_INT_OE ((uint16_t)0x0001U) /*!< PHY Enable output interrupt events */ - -#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020U) /*!< Enable Interrupt on change of link status */ -#define PHY_LINK_INTERRUPT ((uint16_t)0x2000U) /*!< PHY link status interrupt mask */ - -/* ################## SPI peripheral configuration ########################## */ - -/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver -* Activated: CRC code is present inside driver -* Deactivated: CRC code cleaned from driver -*/ - -#define USE_SPI_CRC 0U - -/* Includes ------------------------------------------------------------------*/ -/** - * @brief Include module's header file - */ - -#ifdef HAL_RCC_MODULE_ENABLED -#include "stm32f4xx_hal_rcc.h" -#endif /* HAL_RCC_MODULE_ENABLED */ - -#ifdef HAL_GPIO_MODULE_ENABLED -#include "stm32f4xx_hal_gpio.h" -#endif /* HAL_GPIO_MODULE_ENABLED */ - -#ifdef HAL_DMA_MODULE_ENABLED -#include "stm32f4xx_hal_dma.h" -#endif /* HAL_DMA_MODULE_ENABLED */ - -#ifdef HAL_CORTEX_MODULE_ENABLED -#include "stm32f4xx_hal_cortex.h" -#endif /* HAL_CORTEX_MODULE_ENABLED */ - -#ifdef HAL_ADC_MODULE_ENABLED -#include "stm32f4xx_hal_adc.h" -#endif /* HAL_ADC_MODULE_ENABLED */ - -#ifdef HAL_CAN_MODULE_ENABLED -#include "stm32f4xx_hal_can.h" -#endif /* HAL_CAN_MODULE_ENABLED */ - -#ifdef HAL_CRC_MODULE_ENABLED -#include "stm32f4xx_hal_crc.h" -#endif /* HAL_CRC_MODULE_ENABLED */ - -#ifdef HAL_CRYP_MODULE_ENABLED -#include "stm32f4xx_hal_cryp.h" -#endif /* HAL_CRYP_MODULE_ENABLED */ - -#ifdef HAL_DMA2D_MODULE_ENABLED -#include "stm32f4xx_hal_dma2d.h" -#endif /* HAL_DMA2D_MODULE_ENABLED */ - -#ifdef HAL_DAC_MODULE_ENABLED -#include "stm32f4xx_hal_dac.h" -#endif /* HAL_DAC_MODULE_ENABLED */ - -#ifdef HAL_DCMI_MODULE_ENABLED -#include "stm32f4xx_hal_dcmi.h" -#endif /* HAL_DCMI_MODULE_ENABLED */ - -#ifdef HAL_ETH_MODULE_ENABLED -#include "stm32f4xx_hal_eth.h" -#endif /* HAL_ETH_MODULE_ENABLED */ - -#ifdef HAL_FLASH_MODULE_ENABLED -#include "stm32f4xx_hal_flash.h" -#endif /* HAL_FLASH_MODULE_ENABLED */ - -#ifdef HAL_SRAM_MODULE_ENABLED -#include "stm32f4xx_hal_sram.h" -#endif /* HAL_SRAM_MODULE_ENABLED */ - -#ifdef HAL_NOR_MODULE_ENABLED -#include "stm32f4xx_hal_nor.h" -#endif /* HAL_NOR_MODULE_ENABLED */ - -#ifdef HAL_NAND_MODULE_ENABLED -#include "stm32f4xx_hal_nand.h" -#endif /* HAL_NAND_MODULE_ENABLED */ - -#ifdef HAL_PCCARD_MODULE_ENABLED -#include "stm32f4xx_hal_pccard.h" -#endif /* HAL_PCCARD_MODULE_ENABLED */ - -#ifdef HAL_SDRAM_MODULE_ENABLED -#include "stm32f4xx_hal_sdram.h" -#endif /* HAL_SDRAM_MODULE_ENABLED */ - -#ifdef HAL_HASH_MODULE_ENABLED -#include "stm32f4xx_hal_hash.h" -#endif /* HAL_HASH_MODULE_ENABLED */ - -#ifdef HAL_I2C_MODULE_ENABLED -#include "stm32f4xx_hal_i2c.h" -#endif /* HAL_I2C_MODULE_ENABLED */ - -#ifdef HAL_I2S_MODULE_ENABLED -#include "stm32f4xx_hal_i2s.h" -#endif /* HAL_I2S_MODULE_ENABLED */ - -#ifdef HAL_IWDG_MODULE_ENABLED -#include "stm32f4xx_hal_iwdg.h" -#endif /* HAL_IWDG_MODULE_ENABLED */ - -#ifdef HAL_LTDC_MODULE_ENABLED -#include "stm32f4xx_hal_ltdc.h" -#endif /* HAL_LTDC_MODULE_ENABLED */ - -#ifdef HAL_PWR_MODULE_ENABLED -#include "stm32f4xx_hal_pwr.h" -#endif /* HAL_PWR_MODULE_ENABLED */ - -#ifdef HAL_RNG_MODULE_ENABLED -#include "stm32f4xx_hal_rng.h" -#endif /* HAL_RNG_MODULE_ENABLED */ - -#ifdef HAL_RTC_MODULE_ENABLED -#include "stm32f4xx_hal_rtc.h" -#endif /* HAL_RTC_MODULE_ENABLED */ - -#ifdef HAL_SAI_MODULE_ENABLED -#include "stm32f4xx_hal_sai.h" -#endif /* HAL_SAI_MODULE_ENABLED */ - -#ifdef HAL_SD_MODULE_ENABLED -#include "stm32f4xx_hal_sd.h" -#endif /* HAL_SD_MODULE_ENABLED */ - -#ifdef HAL_SPI_MODULE_ENABLED -#include "stm32f4xx_hal_spi.h" -#endif /* HAL_SPI_MODULE_ENABLED */ - -#ifdef HAL_TIM_MODULE_ENABLED -#include "stm32f4xx_hal_tim.h" -#endif /* HAL_TIM_MODULE_ENABLED */ - -#ifdef HAL_UART_MODULE_ENABLED -#include "stm32f4xx_hal_uart.h" -#endif /* HAL_UART_MODULE_ENABLED */ - -#ifdef HAL_USART_MODULE_ENABLED -#include "stm32f4xx_hal_usart.h" -#endif /* HAL_USART_MODULE_ENABLED */ - -#ifdef HAL_IRDA_MODULE_ENABLED -#include "stm32f4xx_hal_irda.h" -#endif /* HAL_IRDA_MODULE_ENABLED */ - -#ifdef HAL_SMARTCARD_MODULE_ENABLED -#include "stm32f4xx_hal_smartcard.h" -#endif /* HAL_SMARTCARD_MODULE_ENABLED */ - -#ifdef HAL_WWDG_MODULE_ENABLED -#include "stm32f4xx_hal_wwdg.h" -#endif /* HAL_WWDG_MODULE_ENABLED */ - -#ifdef HAL_PCD_MODULE_ENABLED -#include "stm32f4xx_hal_pcd.h" -#endif /* HAL_PCD_MODULE_ENABLED */ - -#ifdef HAL_HCD_MODULE_ENABLED -#include "stm32f4xx_hal_hcd.h" -#endif /* HAL_HCD_MODULE_ENABLED */ - -#ifdef HAL_DSI_MODULE_ENABLED -#include "stm32f4xx_hal_dsi.h" -#endif /* HAL_DSI_MODULE_ENABLED */ - -#ifdef HAL_QSPI_MODULE_ENABLED -#include "stm32f4xx_hal_qspi.h" -#endif /* HAL_QSPI_MODULE_ENABLED */ - -#ifdef HAL_CEC_MODULE_ENABLED -#include "stm32f4xx_hal_cec.h" -#endif /* HAL_CEC_MODULE_ENABLED */ - -#ifdef HAL_FMPI2C_MODULE_ENABLED -#include "stm32f4xx_hal_fmpi2c.h" -#endif /* HAL_FMPI2C_MODULE_ENABLED */ - -#ifdef HAL_SPDIFRX_MODULE_ENABLED -#include "stm32f4xx_hal_spdifrx.h" -#endif /* HAL_SPDIFRX_MODULE_ENABLED */ - -#ifdef HAL_DFSDM_MODULE_ENABLED -#include "stm32f4xx_hal_dfsdm.h" -#endif /* HAL_DFSDM_MODULE_ENABLED */ - -#ifdef HAL_LPTIM_MODULE_ENABLED -#include "stm32f4xx_hal_lptim.h" -#endif /* HAL_LPTIM_MODULE_ENABLED */ - -/* Exported macro ------------------------------------------------------------*/ -#ifdef USE_FULL_ASSERT -/** - * @brief The assert_param macro is used for function's parameters check. - * @param expr: If expr is false, it calls assert_failed function - * which reports the name of the source file and the source - * line number of the call that failed. - * If expr is true, it returns no value. - * @retval None - */ -#define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) -/* Exported functions ------------------------------------------------------- */ -void assert_failed(uint8_t* file, uint32_t line); -#else -#define assert_param(expr) ((void)0) -#endif /* USE_FULL_ASSERT */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F4xx_HAL_CONF_H */ - - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Inc/stm32f4xx_it.h b/EpsilonLights/Inc/stm32f4xx_it.h deleted file mode 100644 index 9e3e861d..00000000 --- a/EpsilonLights/Inc/stm32f4xx_it.h +++ /dev/null @@ -1,67 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_it.h - * @brief This file contains the headers of the interrupt handlers. - ****************************************************************************** - * - * COPYRIGHT(c) 2016 STMicroelectronics - * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_IT_H -#define __STM32F4xx_IT_H - -#ifdef __cplusplus -extern "C" { -#endif - -/* Includes ------------------------------------------------------------------*/ -/* Exported types ------------------------------------------------------------*/ -/* Exported constants --------------------------------------------------------*/ -/* Exported macro ------------------------------------------------------------*/ -/* Exported functions ------------------------------------------------------- */ - -void NMI_Handler(void); -void HardFault_Handler(void); -void MemManage_Handler(void); -void BusFault_Handler(void); -void UsageFault_Handler(void); -void SVC_Handler(void); -void DebugMon_Handler(void); -void PendSV_Handler(void); -void SysTick_Handler(void); -void TIM2_IRQHandler(void); -void CAN2_TX_IRQHandler(void); -void CAN2_RX0_IRQHandler(void); - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F4xx_IT_H */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/EpsilonLights/Makefile b/EpsilonLights/Makefile new file mode 100644 index 00000000..24ff2305 --- /dev/null +++ b/EpsilonLights/Makefile @@ -0,0 +1,208 @@ +########################################################################################################################## +# File automatically-generated by tool: [projectgenerator] version: [3.4.0] date: [Sat May 23 13:52:19 MDT 2020] +########################################################################################################################## + +# ------------------------------------------------ +# Generic Makefile (based on gcc) +# +# ChangeLog : +# 2017-02-10 - Several enhancements + project update mode +# 2015-07-22 - first version +# ------------------------------------------------ + +###################################### +# target +###################################### +TARGET = EpsilonLights + + +###################################### +# building variables +###################################### +# debug build? +DEBUG = 1 +# optimization +OPT = -Og + + +####################################### +# paths +####################################### +# Build path +BUILD_DIR = build + +###################################### +# source +###################################### +# C sources +C_SOURCES = \ +Core/Src/main.c \ +Core/Src/freertos.c \ +Core/Src/Lights.c \ +Core/Src/stm32f1xx_it.c \ +Core/Src/stm32f1xx_hal_msp.c \ +Core/Src/stm32f1xx_hal_timebase_tim.c \ +Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_gpio_ex.c \ +Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_can.c \ +Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_tim.c \ +Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_tim_ex.c \ +Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal.c \ +Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_rcc.c \ +Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_rcc_ex.c \ +Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_gpio.c \ +Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_dma.c \ +Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_cortex.c \ +Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_pwr.c \ +Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_flash.c \ +Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_flash_ex.c \ +Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_exti.c \ +Core/Src/system_stm32f1xx.c \ +Middlewares/Third_Party/FreeRTOS/Source/croutine.c \ +Middlewares/Third_Party/FreeRTOS/Source/event_groups.c \ +Middlewares/Third_Party/FreeRTOS/Source/list.c \ +Middlewares/Third_Party/FreeRTOS/Source/queue.c \ +Middlewares/Third_Party/FreeRTOS/Source/stream_buffer.c \ +Middlewares/Third_Party/FreeRTOS/Source/tasks.c \ +Middlewares/Third_Party/FreeRTOS/Source/timers.c \ +Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS/cmsis_os.c \ +Middlewares/Third_Party/FreeRTOS/Source/portable/MemMang/heap_4.c \ +Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM3/port.c + +# ASM sources +ASM_SOURCES = \ +startup_stm32f103x6.s + + +####################################### +# binaries +####################################### +PREFIX = arm-none-eabi- +# The gcc compiler bin path can be either defined in make command via GCC_PATH variable (> make GCC_PATH=xxx) +# either it can be added to the PATH environment variable. +ifdef GCC_PATH +CC = $(GCC_PATH)/$(PREFIX)gcc +AS = $(GCC_PATH)/$(PREFIX)gcc -x assembler-with-cpp +CP = $(GCC_PATH)/$(PREFIX)objcopy +SZ = $(GCC_PATH)/$(PREFIX)size +else +CC = $(PREFIX)gcc +AS = $(PREFIX)gcc -x assembler-with-cpp +CP = $(PREFIX)objcopy +SZ = $(PREFIX)size +endif +HEX = $(CP) -O ihex +BIN = $(CP) -O binary -S + +####################################### +# CFLAGS +####################################### +# cpu +CPU = -mcpu=cortex-m3 + +# fpu +# NONE for Cortex-M0/M0+/M3 + +# float-abi + + +# mcu +MCU = $(CPU) -mthumb $(FPU) $(FLOAT-ABI) + +# macros for gcc +# AS defines +AS_DEFS = + +# C defines +C_DEFS = \ +-DUSE_HAL_DRIVER \ +-DSTM32F103x6 \ +-DUSE_HAL_DRIVER \ +-DSTM32F103x6 + + +# AS includes +AS_INCLUDES = \ +-ICore/Inc + +# C includes +C_INCLUDES = \ +-ICore/Inc \ +-IDrivers/STM32F1xx_HAL_Driver/Inc \ +-IDrivers/STM32F1xx_HAL_Driver/Inc/Legacy \ +-IMiddlewares/Third_Party/FreeRTOS/Source/include \ +-IMiddlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS \ +-IMiddlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM3 \ +-IDrivers/CMSIS/Device/ST/STM32F1xx/Include \ +-IDrivers/CMSIS/Include + + +# compile gcc flags +ASFLAGS = $(MCU) $(AS_DEFS) $(AS_INCLUDES) $(OPT) -Wall -fdata-sections -ffunction-sections + +CFLAGS = $(MCU) $(C_DEFS) $(C_INCLUDES) $(OPT) -Wall -fdata-sections -ffunction-sections + +ifeq ($(DEBUG), 1) +CFLAGS += -g -gdwarf-2 +endif + + +# Generate dependency information +CFLAGS += -MMD -MP -MF"$(@:%.o=%.d)" + + +####################################### +# LDFLAGS +####################################### +# link script +LDSCRIPT = STM32F103C4Tx_FLASH.ld + +# libraries +LIBS = -lc -lm -lnosys +LIBDIR = +LDFLAGS = $(MCU) -specs=nano.specs -T$(LDSCRIPT) $(LIBDIR) $(LIBS) -Wl,-Map=$(BUILD_DIR)/$(TARGET).map,--cref -Wl,--gc-sections + +# default action: build all +all: $(BUILD_DIR)/$(TARGET).elf $(BUILD_DIR)/$(TARGET).hex $(BUILD_DIR)/$(TARGET).bin + + +####################################### +# build the application +####################################### +# list of objects +OBJECTS = $(addprefix $(BUILD_DIR)/,$(notdir $(C_SOURCES:.c=.o))) +vpath %.c $(sort $(dir $(C_SOURCES))) +# list of ASM program objects +OBJECTS += $(addprefix $(BUILD_DIR)/,$(notdir $(ASM_SOURCES:.s=.o))) +vpath %.s $(sort $(dir $(ASM_SOURCES))) + +$(BUILD_DIR)/%.o: %.c Makefile | $(BUILD_DIR) + $(CC) -c $(CFLAGS) -Wa,-a,-ad,-alms=$(BUILD_DIR)/$(notdir $(<:.c=.lst)) $< -o $@ + +$(BUILD_DIR)/%.o: %.s Makefile | $(BUILD_DIR) + $(AS) -c $(CFLAGS) $< -o $@ + +$(BUILD_DIR)/$(TARGET).elf: $(OBJECTS) Makefile + $(CC) $(OBJECTS) $(LDFLAGS) -o $@ + $(SZ) $@ + +$(BUILD_DIR)/%.hex: $(BUILD_DIR)/%.elf | $(BUILD_DIR) + $(HEX) $< $@ + +$(BUILD_DIR)/%.bin: $(BUILD_DIR)/%.elf | $(BUILD_DIR) + $(BIN) $< $@ + +$(BUILD_DIR): + mkdir $@ + +####################################### +# clean up +####################################### +clean: + -rm -fR $(BUILD_DIR) + +####################################### +# dependencies +####################################### +-include $(wildcard $(BUILD_DIR)/*.d) + +# *** EOF *** diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS/cmsis_os.c b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS/cmsis_os.c index 060fd9ca..6be89ad3 100644 --- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS/cmsis_os.c +++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS/cmsis_os.c @@ -53,52 +53,50 @@ * POSSIBILITY OF SUCH DAMAGE. *---------------------------------------------------------------------------*/ -/** - ****************************************************************************** - * @file cmsis_os.c - * @author MCD Application Team - * @date 22-January-2016 - * @brief CMSIS-RTOS API implementation for FreeRTOS V8.2.3 - ****************************************************************************** - * @attention - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted, provided that the following conditions are met: - * - * 1. Redistribution of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of other - * contributors to this software may be used to endorse or promote products - * derived from this software without specific written permission. - * 4. This software, including modifications and/or derivative works of this - * software, must execute solely and exclusively on microcontroller or - * microprocessor devices manufactured by or for STMicroelectronics. - * 5. Redistribution and use of this software other than as permitted under - * this license is void and will automatically terminate your rights under - * this license. - * - * THIS SOFTWARE IS PROVIDED BY STMICROELECTRONICS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS, IMPLIED OR STATUTORY WARRANTIES, INCLUDING, BUT NOT - * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A - * PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY - * RIGHTS ARE DISCLAIMED TO THE FULLEST EXTENT PERMITTED BY LAW. IN NO EVENT - * SHALL STMICROELECTRONICS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT - * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, - * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF - * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING - * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, - * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - #include #include "cmsis_os.h" +/* + * ARM Compiler 4/5 + */ +#if defined ( __CC_ARM ) + +#define __ASM __asm +#define __INLINE __inline +#define __STATIC_INLINE static __inline + +#include "cmsis_armcc.h" + +/* + * GNU Compiler + */ +#elif defined ( __GNUC__ ) + +#define __ASM __asm /*!< asm keyword for GNU Compiler */ +#define __INLINE inline /*!< inline keyword for GNU Compiler */ +#define __STATIC_INLINE static inline + +#include "cmsis_gcc.h" + + +/* + * IAR Compiler + */ +#elif defined ( __ICCARM__ ) + +#ifndef __ASM +#define __ASM __asm +#endif +#ifndef __INLINE +#define __INLINE inline +#endif +#ifndef __STATIC_INLINE +#define __STATIC_INLINE static inline +#endif + +#include +#endif + extern void xPortSysTickHandler(void); /* Convert from CMSIS type osPriority to FreeRTOS priority number */ @@ -154,6 +152,7 @@ osStatus osKernelInitialize (void); osStatus osKernelStart (void) { vTaskStartScheduler(); + return osOK; } @@ -214,6 +213,31 @@ osThreadId osThreadCreate (const osThreadDef_t* thread_def, void* argument) { TaskHandle_t handle; +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) + + if ((thread_def->buffer != NULL) && (thread_def->controlblock != NULL)) + { + handle = xTaskCreateStatic((TaskFunction_t)thread_def->pthread, (const portCHAR*)thread_def->name, + thread_def->stacksize, argument, makeFreeRtosPriority(thread_def->tpriority), + thread_def->buffer, thread_def->controlblock); + } + else + { + if (xTaskCreate((TaskFunction_t)thread_def->pthread, (const portCHAR*)thread_def->name, + thread_def->stacksize, argument, makeFreeRtosPriority(thread_def->tpriority), + &handle) != pdPASS) + { + return NULL; + } + } + +#elif( configSUPPORT_STATIC_ALLOCATION == 1 ) + + handle = xTaskCreateStatic((TaskFunction_t)thread_def->pthread, (const portCHAR*)thread_def->name, + thread_def->stacksize, argument, makeFreeRtosPriority(thread_def->tpriority), + thread_def->buffer, thread_def->controlblock); +#else + if (xTaskCreate((TaskFunction_t)thread_def->pthread, (const portCHAR*)thread_def->name, thread_def->stacksize, argument, makeFreeRtosPriority(thread_def->tpriority), &handle) != pdPASS) @@ -221,6 +245,8 @@ osThreadId osThreadCreate (const osThreadDef_t* thread_def, void* argument) return NULL; } +#endif + return handle; } @@ -262,6 +288,7 @@ osStatus osThreadTerminate (osThreadId thread_id) osStatus osThreadYield (void) { taskYIELD(); + return osOK; } @@ -316,10 +343,13 @@ osStatus osDelay (uint32_t millisec) { #if INCLUDE_vTaskDelay TickType_t ticks = millisec / portTICK_PERIOD_MS; + vTaskDelay(ticks ? ticks : 1); /* Minimum delay = 1 tick */ + return osOK; #else (void) millisec; + return osErrorResource; #endif } @@ -347,11 +377,42 @@ osEvent osWait (uint32_t millisec); osTimerId osTimerCreate (const osTimerDef_t* timer_def, os_timer_type type, void* argument) { #if (configUSE_TIMERS == 1) + +#if( ( configSUPPORT_STATIC_ALLOCATION == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) ) + + if (timer_def->controlblock != NULL) + { + return xTimerCreateStatic((const char*)"", + 1, // period should be filled when starting the Timer using osTimerStart + (type == osTimerPeriodic) ? pdTRUE : pdFALSE, + (void*) argument, + (TaskFunction_t)timer_def->ptimer, + (StaticTimer_t*)timer_def->controlblock); + } + else + { + return xTimerCreate((const char*)"", + 1, // period should be filled when starting the Timer using osTimerStart + (type == osTimerPeriodic) ? pdTRUE : pdFALSE, + (void*) argument, + (TaskFunction_t)timer_def->ptimer); + } + +#elif( configSUPPORT_STATIC_ALLOCATION == 1 ) + return xTimerCreateStatic((const char*)"", + 1, // period should be filled when starting the Timer using osTimerStart + (type == osTimerPeriodic) ? pdTRUE : pdFALSE, + (void*) argument, + (TaskFunction_t)timer_def->ptimer, + (StaticTimer_t*)timer_def->controlblock); +#else return xTimerCreate((const char*)"", 1, // period should be filled when starting the Timer using osTimerStart (type == osTimerPeriodic) ? pdTRUE : pdFALSE, (void*) argument, (TaskFunction_t)timer_def->ptimer); +#endif + #else return NULL; #endif @@ -445,6 +506,7 @@ osStatus osTimerStop (osTimerId timer_id) osStatus osTimerDelete (osTimerId timer_id) { osStatus result = osOK; + #if (configUSE_TIMERS == 1) if (inHandlerMode()) @@ -462,6 +524,7 @@ osStatus osTimerDelete (osTimerId timer_id) #else result = osErrorOS; #endif + return result; } @@ -470,33 +533,35 @@ osStatus osTimerDelete (osTimerId timer_id) * @brief Set the specified Signal Flags of an active thread. * @param thread_id thread ID obtained by \ref osThreadCreate or \ref osThreadGetId. * @param signals specifies the signal flags of the thread that should be set. -* @retval osOK if successful, osErrorOS if failed . +* @retval previous signal flags of the specified thread or 0x80000000 in case of incorrect parameters. * @note MUST REMAIN UNCHANGED: \b osSignalSet shall be consistent in every CMSIS-RTOS. */ int32_t osSignalSet (osThreadId thread_id, int32_t signal) { #if( configUSE_TASK_NOTIFICATIONS == 1 ) BaseType_t xHigherPriorityTaskWoken = pdFALSE; + uint32_t ulPreviousNotificationValue = 0; if (inHandlerMode()) { - if (xTaskNotifyFromISR( thread_id, (uint32_t)signal, eSetBits, &xHigherPriorityTaskWoken ) != pdPASS ) + if (xTaskGenericNotifyFromISR( thread_id, (uint32_t)signal, eSetBits, &ulPreviousNotificationValue, &xHigherPriorityTaskWoken ) != pdPASS ) { - return osErrorOS; + return 0x80000000; } portYIELD_FROM_ISR( xHigherPriorityTaskWoken ); } - else if (xTaskNotify( thread_id, (uint32_t)signal, eSetBits) != pdPASS ) + else if (xTaskGenericNotify( thread_id, (uint32_t)signal, eSetBits, &ulPreviousNotificationValue) != pdPASS ) { - return osErrorOS; + return 0x80000000; } - return osOK; + return ulPreviousNotificationValue; #else (void) thread_id; (void) signal; - return osErrorOS; /* Task Notification not supported */ + + return 0x80000000; /* Task Notification not supported */ #endif } @@ -519,8 +584,11 @@ int32_t osSignalClear (osThreadId thread_id, int32_t signal); osEvent osSignalWait (int32_t signals, uint32_t millisec) { osEvent ret; + #if( configUSE_TASK_NOTIFICATIONS == 1 ) + TickType_t ticks; + ret.value.signals = 0; ticks = 0; @@ -568,8 +636,10 @@ osEvent osSignalWait (int32_t signals, uint32_t millisec) #else (void) signals; (void) millisec; + ret.status = osErrorOS; /* Task Notification not supported */ #endif + return ret; } @@ -583,7 +653,23 @@ osEvent osSignalWait (int32_t signals, uint32_t millisec) osMutexId osMutexCreate (const osMutexDef_t* mutex_def) { #if ( configUSE_MUTEXES == 1) + +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) + + if (mutex_def->controlblock != NULL) + { + return xSemaphoreCreateMutexStatic( mutex_def->controlblock ); + } + else + { + return xSemaphoreCreateMutex(); + } + +#elif ( configSUPPORT_STATIC_ALLOCATION == 1 ) + return xSemaphoreCreateMutexStatic( mutex_def->controlblock ); +#else return xSemaphoreCreateMutex(); +#endif #else return NULL; #endif @@ -601,6 +687,7 @@ osStatus osMutexWait (osMutexId mutex_id, uint32_t millisec) TickType_t ticks; portBASE_TYPE taskWoken = pdFALSE; + if (mutex_id == NULL) { return osErrorParameter; @@ -681,6 +768,7 @@ osStatus osMutexDelete (osMutexId mutex_id) } vQueueDelete(mutex_id); + return osOK; } @@ -697,7 +785,58 @@ osStatus osMutexDelete (osMutexId mutex_id) */ osSemaphoreId osSemaphoreCreate (const osSemaphoreDef_t* semaphore_def, int32_t count) { - (void) semaphore_def; +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) + + osSemaphoreId sema; + + if (semaphore_def->controlblock != NULL) + { + if (count == 1) + { + return xSemaphoreCreateBinaryStatic( semaphore_def->controlblock ); + } + else + { +#if (configUSE_COUNTING_SEMAPHORES == 1 ) + return xSemaphoreCreateCountingStatic( count, count, semaphore_def->controlblock ); +#else + return NULL; +#endif + } + } + else + { + if (count == 1) + { + vSemaphoreCreateBinary(sema); + return sema; + } + else + { +#if (configUSE_COUNTING_SEMAPHORES == 1 ) + return xSemaphoreCreateCounting(count, count); +#else + return NULL; +#endif + } + } + +#elif ( configSUPPORT_STATIC_ALLOCATION == 1 ) // configSUPPORT_DYNAMIC_ALLOCATION == 0 + + if (count == 1) + { + return xSemaphoreCreateBinaryStatic( semaphore_def->controlblock ); + } + else + { +#if (configUSE_COUNTING_SEMAPHORES == 1 ) + return xSemaphoreCreateCountingStatic( count, count, semaphore_def->controlblock ); +#else + return NULL; +#endif + } + +#else // configSUPPORT_STATIC_ALLOCATION == 0 && configSUPPORT_DYNAMIC_ALLOCATION == 1 osSemaphoreId sema; if (count == 1) @@ -705,11 +844,15 @@ osSemaphoreId osSemaphoreCreate (const osSemaphoreDef_t* semaphore_def, int32_t vSemaphoreCreateBinary(sema); return sema; } - + else + { #if (configUSE_COUNTING_SEMAPHORES == 1 ) - return xSemaphoreCreateCounting(count, 0); + return xSemaphoreCreateCounting(count, count); #else - return NULL; + return NULL; +#endif + } + #endif } @@ -725,6 +868,7 @@ int32_t osSemaphoreWait (osSemaphoreId semaphore_id, uint32_t millisec) TickType_t ticks; portBASE_TYPE taskWoken = pdFALSE; + if (semaphore_id == NULL) { return osErrorParameter; @@ -774,6 +918,7 @@ osStatus osSemaphoreRelease (osSemaphoreId semaphore_id) osStatus result = osOK; portBASE_TYPE taskWoken = pdFALSE; + if (inHandlerMode()) { if (xSemaphoreGiveFromISR(semaphore_id, &taskWoken) != pdTRUE) @@ -808,6 +953,7 @@ osStatus osSemaphoreDelete (osSemaphoreId semaphore_id) } vSemaphoreDelete(semaphore_id); + return osOK; } @@ -840,17 +986,21 @@ typedef struct os_pool_cb */ osPoolId osPoolCreate (const osPoolDef_t* pool_def) { +#if (configSUPPORT_DYNAMIC_ALLOCATION == 1) osPoolId thePool; int itemSize = 4 * ((pool_def->item_sz + 3) / 4); uint32_t i; + /* First have to allocate memory for the pool control block. */ thePool = pvPortMalloc(sizeof(os_pool_cb_t)); + if (thePool) { thePool->pool_sz = pool_def->pool_sz; thePool->item_sz = itemSize; thePool->currentIndex = 0; + /* Memory for markers */ thePool->markers = pvPortMalloc(pool_def->pool_sz); @@ -881,6 +1031,10 @@ osPoolId osPoolCreate (const osPoolDef_t* pool_def) } return thePool; + +#else + return NULL; +#endif } /** @@ -907,12 +1061,7 @@ void* osPoolAlloc (osPoolId pool_id) for (i = 0; i < pool_id->pool_sz; i++) { - index = pool_id->currentIndex + i; - - if (index >= pool_id->pool_sz) - { - index = 0; - } + index = (pool_id->currentIndex + i) % pool_id->pool_sz; if (pool_id->markers[index] == 0) { @@ -994,6 +1143,7 @@ osStatus osPoolFree (osPoolId pool_id, void* block) } pool_id->markers[index] = 0; + return osOK; } @@ -1014,7 +1164,23 @@ osStatus osPoolFree (osPoolId pool_id, void* block) osMessageQId osMessageCreate (const osMessageQDef_t* queue_def, osThreadId thread_id) { (void) thread_id; + +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) + + if ((queue_def->buffer != NULL) && (queue_def->controlblock != NULL)) + { + return xQueueCreateStatic(queue_def->queue_sz, queue_def->item_sz, queue_def->buffer, queue_def->controlblock); + } + else + { + return xQueueCreate(queue_def->queue_sz, queue_def->item_sz); + } + +#elif ( configSUPPORT_STATIC_ALLOCATION == 1 ) + return xQueueCreateStatic(queue_def->queue_sz, queue_def->item_sz, queue_def->buffer, queue_def->controlblock); +#else return xQueueCreate(queue_def->queue_sz, queue_def->item_sz); +#endif } /** @@ -1029,6 +1195,7 @@ osStatus osMessagePut (osMessageQId queue_id, uint32_t info, uint32_t millisec) { portBASE_TYPE taskWoken = pdFALSE; TickType_t ticks; + ticks = millisec / portTICK_PERIOD_MS; if (ticks == 0) @@ -1068,6 +1235,7 @@ osEvent osMessageGet (osMessageQId queue_id, uint32_t millisec) portBASE_TYPE taskWoken; TickType_t ticks; osEvent event; + event.def.message_id = queue_id; event.value.v = 0; @@ -1078,6 +1246,7 @@ osEvent osMessageGet (osMessageQId queue_id, uint32_t millisec) } taskWoken = pdFALSE; + ticks = 0; if (millisec == osWaitForever) @@ -1146,9 +1315,13 @@ typedef struct os_mailQ_cb */ osMailQId osMailCreate (const osMailQDef_t* queue_def, osThreadId thread_id) { +#if (configSUPPORT_DYNAMIC_ALLOCATION == 1) (void) thread_id; + osPoolDef_t pool_def = {queue_def->queue_sz, queue_def->item_sz, NULL}; + /* Create a mail queue control block */ + *(queue_def->cb) = pvPortMalloc(sizeof(struct os_mailQ_cb)); if (*(queue_def->cb) == NULL) @@ -1157,9 +1330,11 @@ osMailQId osMailCreate (const osMailQDef_t* queue_def, osThreadId thread_id) } (*(queue_def->cb))->queue_def = queue_def; + /* Create a queue in FreeRTOS */ (*(queue_def->cb))->handle = xQueueCreate(queue_def->queue_sz, sizeof(void*)); + if ((*(queue_def->cb))->handle == NULL) { vPortFree(*(queue_def->cb)); @@ -1177,6 +1352,9 @@ osMailQId osMailCreate (const osMailQDef_t* queue_def, osThreadId thread_id) } return *(queue_def->cb); +#else + return NULL; +#endif } /** @@ -1191,12 +1369,14 @@ void* osMailAlloc (osMailQId queue_id, uint32_t millisec) (void) millisec; void* p; + if (queue_id == NULL) { return NULL; } p = osPoolAlloc(queue_id->pool); + return p; } @@ -1214,7 +1394,7 @@ void* osMailCAlloc (osMailQId queue_id, uint32_t millisec) if (p) { - for (i = 0; i < sizeof(queue_id->queue_def->item_sz); i++) + for (i = 0; i < queue_id->queue_def->item_sz; i++) { ((uint8_t*)p)[i] = 0; } @@ -1234,6 +1414,7 @@ osStatus osMailPut (osMailQId queue_id, void* mail) { portBASE_TYPE taskWoken; + if (queue_id == NULL) { return osErrorParameter; @@ -1273,6 +1454,7 @@ osEvent osMailGet (osMailQId queue_id, uint32_t millisec) portBASE_TYPE taskWoken; TickType_t ticks; osEvent event; + event.def.mail_id = queue_id; if (queue_id == NULL) @@ -1282,6 +1464,7 @@ osEvent osMailGet (osMailQId queue_id, uint32_t millisec) } taskWoken = pdFALSE; + ticks = 0; if (millisec == osWaitForever) @@ -1354,6 +1537,7 @@ osStatus osMailFree (osMailQId queue_id, void* mail) */ void osSystickHandler(void) { + #if (INCLUDE_xTaskGetSchedulerState == 1 ) if (xTaskGetSchedulerState() != taskSCHEDULER_NOT_STARTED) @@ -1376,6 +1560,7 @@ osThreadState osThreadGetState(osThreadId thread_id) { eTaskState ThreadState; osThreadState result; + ThreadState = eTaskGetState(thread_id); switch (ThreadState) @@ -1435,6 +1620,7 @@ osStatus osThreadSuspend (osThreadId thread_id) { #if (INCLUDE_vTaskSuspend == 1) vTaskSuspend(thread_id); + return osOK; #else return osErrorResource; @@ -1475,6 +1661,7 @@ osStatus osThreadResume (osThreadId thread_id) osStatus osThreadSuspendAll (void) { vTaskSuspendAll(); + return osOK; } @@ -1492,6 +1679,7 @@ osStatus osThreadResumeAll (void) { return osErrorOS; } + } /** @@ -1507,10 +1695,31 @@ osStatus osDelayUntil (uint32_t* PreviousWakeTime, uint32_t millisec) #if INCLUDE_vTaskDelayUntil TickType_t ticks = (millisec / portTICK_PERIOD_MS); vTaskDelayUntil((TickType_t*) PreviousWakeTime, ticks ? ticks : 1); + return osOK; #else (void) millisec; (void) PreviousWakeTime; + + return osErrorResource; +#endif +} + +/** +* @brief Abort the delay for a specific thread +* @param thread_id thread ID obtained by \ref osThreadCreate or \ref osThreadGetId +* @retval status code that indicates the execution status of the function. +*/ +osStatus osAbortDelay(osThreadId thread_id) +{ +#if INCLUDE_xTaskAbortDelay + + xTaskAbortDelay(thread_id); + + return osOK; +#else + (void) thread_id; + return osErrorResource; #endif } @@ -1540,6 +1749,7 @@ osEvent osMessagePeek (osMessageQId queue_id, uint32_t millisec) { TickType_t ticks; osEvent event; + event.def.message_id = queue_id; if (queue_id == NULL) @@ -1577,6 +1787,50 @@ osEvent osMessagePeek (osMessageQId queue_id, uint32_t millisec) return event; } +/** +* @brief Get the number of messaged stored in a queue. +* @param queue_id message queue ID obtained with \ref osMessageCreate. +* @retval number of messages stored in a queue. +*/ +uint32_t osMessageWaiting(osMessageQId queue_id) +{ + if (inHandlerMode()) + { + return uxQueueMessagesWaitingFromISR(queue_id); + } + else + { + return uxQueueMessagesWaiting(queue_id); + } +} + +/** +* @brief Get the available space in a message queue. +* @param queue_id message queue ID obtained with \ref osMessageCreate. +* @retval available space in a message queue. +*/ +uint32_t osMessageAvailableSpace(osMessageQId queue_id) +{ + return uxQueueSpacesAvailable(queue_id); +} + +/** +* @brief Delete a Message Queue +* @param queue_id message queue ID obtained with \ref osMessageCreate. +* @retval status code that indicates the execution status of the function. +*/ +osStatus osMessageDelete (osMessageQId queue_id) +{ + if (inHandlerMode()) + { + return osErrorISR; + } + + vQueueDelete(queue_id); + + return osOK; +} + /** * @brief Create and Initialize a Recursive Mutex * @param mutex_def mutex definition referenced with \ref osMutex. @@ -1584,9 +1838,23 @@ osEvent osMessagePeek (osMessageQId queue_id, uint32_t millisec) */ osMutexId osRecursiveMutexCreate (const osMutexDef_t* mutex_def) { - (void) mutex_def; #if (configUSE_RECURSIVE_MUTEXES == 1) +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) + + if (mutex_def->controlblock != NULL) + { + return xSemaphoreCreateRecursiveMutexStatic( mutex_def->controlblock ); + } + else + { + return xSemaphoreCreateRecursiveMutex(); + } + +#elif ( configSUPPORT_STATIC_ALLOCATION == 1 ) + return xSemaphoreCreateRecursiveMutexStatic( mutex_def->controlblock ); +#else return xSemaphoreCreateRecursiveMutex(); +#endif #else return NULL; #endif @@ -1655,3 +1923,13 @@ osStatus osRecursiveMutexWait (osMutexId mutex_id, uint32_t millisec) return osErrorResource; #endif } + +/** +* @brief Returns the current count value of a counting semaphore +* @param semaphore_id semaphore_id ID obtained by \ref osSemaphoreCreate. +* @retval count value +*/ +uint32_t osSemaphoreGetCount(osSemaphoreId semaphore_id) +{ + return uxSemaphoreGetCount(semaphore_id); +} diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS/cmsis_os.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS/cmsis_os.h index b77762ee..bf225227 100644 --- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS/cmsis_os.h +++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS/cmsis_os.h @@ -53,69 +53,6 @@ * POSSIBILITY OF SUCH DAMAGE. *---------------------------------------------------------------------------*/ -/** - ****************************************************************************** - * @file cmsis_os.h - * @author MCD Application Team - * @date 22-January-2016 - * @brief Header of cmsis_os.c - * A new set of APIs are added in addition to existing ones, these APIs - * are specific to FreeRTOS. - ****************************************************************************** - * @attention - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted, provided that the following conditions are met: - * - * 1. Redistribution of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of other - * contributors to this software may be used to endorse or promote products - * derived from this software without specific written permission. - * 4. This software, including modifications and/or derivative works of this - * software, must execute solely and exclusively on microcontroller or - * microprocessor devices manufactured by or for STMicroelectronics. - * 5. Redistribution and use of this software other than as permitted under - * this license is void and will automatically terminate your rights under - * this license. - * - * THIS SOFTWARE IS PROVIDED BY STMICROELECTRONICS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS, IMPLIED OR STATUTORY WARRANTIES, INCLUDING, BUT NOT - * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A - * PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY - * RIGHTS ARE DISCLAIMED TO THE FULLEST EXTENT PERMITTED BY LAW. IN NO EVENT - * SHALL STMICROELECTRONICS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT - * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, - * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF - * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING - * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, - * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -#if defined ( __CC_ARM ) -#define __ASM __asm /*!< asm keyword for ARM Compiler */ -#define __INLINE __inline /*!< inline keyword for ARM Compiler */ -#define __STATIC_INLINE static __inline -#elif defined ( __ICCARM__ ) -#define __ASM __asm /*!< asm keyword for IAR Compiler */ -#define __INLINE inline /*!< inline keyword for IAR Compiler. Only available in High optimization mode! */ -#define __STATIC_INLINE static inline -#elif defined ( __GNUC__ ) -#define __ASM __asm /*!< asm keyword for GNU Compiler */ -#define __INLINE inline /*!< inline keyword for GNU Compiler */ -#define __STATIC_INLINE static inline -#endif - -#include -#include -#include "core_cmFunc.h" - #include "FreeRTOS.h" #include "task.h" #include "timers.h" @@ -329,6 +266,19 @@ typedef QueueHandle_t osMessageQId; typedef struct os_mailQ_cb* osMailQId; +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) + +typedef StaticTask_t osStaticThreadDef_t; +typedef StaticTimer_t osStaticTimerDef_t; +typedef StaticSemaphore_t osStaticMutexDef_t; +typedef StaticSemaphore_t osStaticSemaphoreDef_t; +typedef StaticQueue_t osStaticMessageQDef_t; + +#endif + + + + /// Thread Definition structure contains startup information of a thread. /// \note CAN BE CHANGED: \b os_thread_def is implementation specific in every CMSIS-RTOS. typedef struct os_thread_def @@ -338,6 +288,10 @@ typedef struct os_thread_def osPriority tpriority; ///< initial thread priority uint32_t instances; ///< maximum number of instances of that thread function uint32_t stacksize; ///< stack size requirements in bytes; 0 is default stack size +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) + uint32_t* buffer; ///< stack buffer for static allocation; NULL for dynamic allocation + osStaticThreadDef_t* controlblock; ///< control block to hold thread's data for static allocation; NULL for dynamic allocation +#endif } osThreadDef_t; /// Timer Definition structure contains timer parameters. @@ -345,6 +299,9 @@ typedef struct os_thread_def typedef struct os_timer_def { os_ptimer ptimer; ///< start address of a timer function +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) + osStaticTimerDef_t* controlblock; ///< control block to hold timer's data for static allocation; NULL for dynamic allocation +#endif } osTimerDef_t; /// Mutex Definition structure contains setup information for a mutex. @@ -352,6 +309,9 @@ typedef struct os_timer_def typedef struct os_mutex_def { uint32_t dummy; ///< dummy value. +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) + osStaticMutexDef_t* controlblock; ///< control block for static allocation; NULL for dynamic allocation +#endif } osMutexDef_t; /// Semaphore Definition structure contains setup information for a semaphore. @@ -359,6 +319,9 @@ typedef struct os_mutex_def typedef struct os_semaphore_def { uint32_t dummy; ///< dummy value. +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) + osStaticSemaphoreDef_t* controlblock; ///< control block for static allocation; NULL for dynamic allocation +#endif } osSemaphoreDef_t; /// Definition structure for memory block allocation. @@ -375,7 +338,11 @@ typedef struct os_pool_def typedef struct os_messageQ_def { uint32_t queue_sz; ///< number of elements in the queue - uint32_t item_sz; ///< size of an item + uint32_t item_sz; ///< size of an item +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) + uint8_t* buffer; ///< buffer for static allocation; NULL for dynamic allocation + osStaticMessageQDef_t* controlblock; ///< control block to hold queue's data for static allocation; NULL for dynamic allocation +#endif //void *pool; ///< memory array for messages } osMessageQDef_t; @@ -456,9 +423,21 @@ uint32_t osKernelSysTick (void); #define osThreadDef(name, thread, priority, instances, stacksz) \ extern const osThreadDef_t os_thread_def_##name #else // define the object + +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) +#define osThreadDef(name, thread, priority, instances, stacksz) \ +const osThreadDef_t os_thread_def_##name = \ +{ #name, (thread), (priority), (instances), (stacksz), NULL, NULL } + +#define osThreadStaticDef(name, thread, priority, instances, stacksz, buffer, control) \ +const osThreadDef_t os_thread_def_##name = \ +{ #name, (thread), (priority), (instances), (stacksz), (buffer), (control) } +#else //configSUPPORT_STATIC_ALLOCATION == 0 + #define osThreadDef(name, thread, priority, instances, stacksz) \ const osThreadDef_t os_thread_def_##name = \ -{ #name, (thread), (priority), (instances), (stacksz) } +{ #name, (thread), (priority), (instances), (stacksz)} +#endif #endif /// Access a Thread definition. @@ -533,10 +512,21 @@ osEvent osWait (uint32_t millisec); #define osTimerDef(name, function) \ extern const osTimerDef_t os_timer_def_##name #else // define the object + +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) +#define osTimerDef(name, function) \ +const osTimerDef_t os_timer_def_##name = \ +{ (function), NULL } + +#define osTimerStaticDef(name, function, control) \ +const osTimerDef_t os_timer_def_##name = \ +{ (function), (control) } +#else //configSUPPORT_STATIC_ALLOCATION == 0 #define osTimerDef(name, function) \ const osTimerDef_t os_timer_def_##name = \ { (function) } #endif +#endif /// Access a Timer definition. /// \param name name of the timer object. @@ -607,8 +597,19 @@ osEvent osSignalWait (int32_t signals, uint32_t millisec); #define osMutexDef(name) \ extern const osMutexDef_t os_mutex_def_##name #else // define the object + +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) +#define osMutexDef(name) \ +const osMutexDef_t os_mutex_def_##name = { 0, NULL } + +#define osMutexStaticDef(name, control) \ +const osMutexDef_t os_mutex_def_##name = { 0, (control) } +#else //configSUPPORT_STATIC_ALLOCATION == 0 #define osMutexDef(name) \ const osMutexDef_t os_mutex_def_##name = { 0 } + +#endif + #endif /// Access a Mutex definition. @@ -656,9 +657,19 @@ osStatus osMutexDelete (osMutexId mutex_id); #define osSemaphoreDef(name) \ extern const osSemaphoreDef_t os_semaphore_def_##name #else // define the object + +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) +#define osSemaphoreDef(name) \ +const osSemaphoreDef_t os_semaphore_def_##name = { 0, NULL } + +#define osSemaphoreStaticDef(name, control) \ +const osSemaphoreDef_t os_semaphore_def_##name = { 0, (control) } + +#else //configSUPPORT_STATIC_ALLOCATION == 0 #define osSemaphoreDef(name) \ const osSemaphoreDef_t os_semaphore_def_##name = { 0 } #endif +#endif /// Access a Semaphore definition. /// \param name name of the semaphore object. @@ -764,9 +775,20 @@ osStatus osPoolFree (osPoolId pool_id, void* block); #define osMessageQDef(name, queue_sz, type) \ extern const osMessageQDef_t os_messageQ_def_##name #else // define the object +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) +#define osMessageQDef(name, queue_sz, type) \ +const osMessageQDef_t os_messageQ_def_##name = \ +{ (queue_sz), sizeof (type), NULL, NULL } + +#define osMessageQStaticDef(name, queue_sz, type, buffer, control) \ +const osMessageQDef_t os_messageQ_def_##name = \ +{ (queue_sz), sizeof (type) , (buffer), (control)} +#else //configSUPPORT_STATIC_ALLOCATION == 1 #define osMessageQDef(name, queue_sz, type) \ const osMessageQDef_t os_messageQ_def_##name = \ -{ (queue_sz), sizeof (type) } +{ (queue_sz), sizeof (type) } + +#endif #endif /// \brief Access a Message Queue Definition. @@ -937,6 +959,13 @@ osStatus osThreadResumeAll (void); */ osStatus osDelayUntil (uint32_t* PreviousWakeTime, uint32_t millisec); +/** +* @brief Abort the delay for a specific thread +* @param thread_id thread ID obtained by \ref osThreadCreate or \ref osThreadGetId +* @retval status code that indicates the execution status of the function. +*/ +osStatus osAbortDelay(osThreadId thread_id); + /** * @brief Lists all the current threads, along with their current state * and stack usage high water mark. @@ -954,6 +983,27 @@ osStatus osThreadList (uint8_t* buffer); */ osEvent osMessagePeek (osMessageQId queue_id, uint32_t millisec); +/** +* @brief Get the number of messaged stored in a queue. +* @param queue_id message queue ID obtained with \ref osMessageCreate. +* @retval number of messages stored in a queue. +*/ +uint32_t osMessageWaiting(osMessageQId queue_id); + +/** +* @brief Get the available space in a message queue. +* @param queue_id message queue ID obtained with \ref osMessageCreate. +* @retval available space in a message queue. +*/ +uint32_t osMessageAvailableSpace(osMessageQId queue_id); + +/** +* @brief Delete a Message Queue +* @param queue_id message queue ID obtained with \ref osMessageCreate. +* @retval status code that indicates the execution status of the function. +*/ +osStatus osMessageDelete (osMessageQId queue_id); + /** * @brief Create and Initialize a Recursive Mutex * @param mutex_def mutex definition referenced with \ref osMutex. @@ -976,6 +1026,13 @@ osStatus osRecursiveMutexRelease (osMutexId mutex_id); */ osStatus osRecursiveMutexWait (osMutexId mutex_id, uint32_t millisec); +/** +* @brief Returns the current count value of a counting semaphore +* @param semaphore_id semaphore_id ID obtained by \ref osSemaphoreCreate. +* @retval count value +*/ +uint32_t osSemaphoreGetCount(osSemaphoreId semaphore_id); + #ifdef __cplusplus } #endif diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/croutine.c b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/croutine.c index abbb3e3e..af7c8592 100644 --- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/croutine.c +++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/croutine.c @@ -1,71 +1,29 @@ /* - FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd. - All rights reserved - - VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION. - - This file is part of the FreeRTOS distribution. - - FreeRTOS is free software; you can redistribute it and/or modify it under - the terms of the GNU General Public License (version 2) as published by the - Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception. - - *************************************************************************** - >>! NOTE: The modification to the GPL is included to allow you to !<< - >>! distribute a combined work that includes FreeRTOS without being !<< - >>! obliged to provide the source code for proprietary components !<< - >>! outside of the FreeRTOS kernel. !<< - *************************************************************************** - - FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY - WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS - FOR A PARTICULAR PURPOSE. Full license text is available on the following - link: http://www.freertos.org/a00114.html - - *************************************************************************** - * * - * FreeRTOS provides completely free yet professionally developed, * - * robust, strictly quality controlled, supported, and cross * - * platform software that is more than just the market leader, it * - * is the industry's de facto standard. * - * * - * Help yourself get started quickly while simultaneously helping * - * to support the FreeRTOS project by purchasing a FreeRTOS * - * tutorial book, reference manual, or both: * - * http://www.FreeRTOS.org/Documentation * - * * - *************************************************************************** - - http://www.FreeRTOS.org/FAQHelp.html - Having a problem? Start by reading - the FAQ page "My application does not run, what could be wrong?". Have you - defined configASSERT()? - - http://www.FreeRTOS.org/support - In return for receiving this top quality - embedded software for free we request you assist our global community by - participating in the support forum. - - http://www.FreeRTOS.org/training - Investing in training allows your team to - be as productive as possible as early as possible. Now you can receive - FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers - Ltd, and the world's leading authority on the world's leading RTOS. - - http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products, - including FreeRTOS+Trace - an indispensable productivity tool, a DOS - compatible FAT file system, and our tiny thread aware UDP/IP stack. - - http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate. - Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS. - - http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High - Integrity Systems ltd. to sell under the OpenRTOS brand. Low cost OpenRTOS - licenses offer ticketed support, indemnification and commercial middleware. - - http://www.SafeRTOS.com - High Integrity Systems also provide a safety - engineered and independently SIL3 certified version for use in safety and - mission critical applications that require provable dependability. - - 1 tab == 4 spaces! -*/ + * FreeRTOS Kernel V10.0.1 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ #include "FreeRTOS.h" #include "task.h" @@ -145,6 +103,7 @@ BaseType_t xCoRoutineCreate( crCOROUTINE_CODE pxCoRoutineCode, UBaseType_t uxPri { BaseType_t xReturn; CRCB_t* pxCoRoutine; + /* Allocate the memory that will store the co-routine control block. */ pxCoRoutine = ( CRCB_t* ) pvPortMalloc( sizeof( CRCB_t ) ); @@ -169,19 +128,24 @@ BaseType_t xCoRoutineCreate( crCOROUTINE_CODE pxCoRoutineCode, UBaseType_t uxPri pxCoRoutine->uxPriority = uxPriority; pxCoRoutine->uxIndex = uxIndex; pxCoRoutine->pxCoRoutineFunction = pxCoRoutineCode; + /* Initialise all the other co-routine control block parameters. */ vListInitialiseItem( &( pxCoRoutine->xGenericListItem ) ); vListInitialiseItem( &( pxCoRoutine->xEventListItem ) ); + /* Set the co-routine control block as a link back from the ListItem_t. This is so we can get back to the containing CRCB from a generic item in a list. */ listSET_LIST_ITEM_OWNER( &( pxCoRoutine->xGenericListItem ), pxCoRoutine ); listSET_LIST_ITEM_OWNER( &( pxCoRoutine->xEventListItem ), pxCoRoutine ); + /* Event lists are always in priority order. */ listSET_LIST_ITEM_VALUE( &( pxCoRoutine->xEventListItem ), ( ( TickType_t ) configMAX_CO_ROUTINE_PRIORITIES - ( TickType_t ) uxPriority ) ); + /* Now the co-routine has been initialised it can be added to the ready list at the correct priority. */ prvAddCoRoutineToReadyQueue( pxCoRoutine ); + xReturn = pdPASS; } else @@ -196,13 +160,16 @@ BaseType_t xCoRoutineCreate( crCOROUTINE_CODE pxCoRoutineCode, UBaseType_t uxPri void vCoRoutineAddToDelayedList( TickType_t xTicksToDelay, List_t* pxEventList ) { TickType_t xTimeToWake; + /* Calculate the time to wake - this may overflow but this is not a problem. */ xTimeToWake = xCoRoutineTickCount + xTicksToDelay; + /* We must remove ourselves from the ready list before adding ourselves to the blocked list as the same list item is used for both lists. */ ( void ) uxListRemove( ( ListItem_t* ) & ( pxCurrentCoRoutine->xGenericListItem ) ); + /* The list item will be inserted in wake time order. */ listSET_LIST_ITEM_VALUE( &( pxCurrentCoRoutine->xGenericListItem ), xTimeToWake ); @@ -236,6 +203,7 @@ static void prvCheckPendingReadyList( void ) while ( listLIST_IS_EMPTY( &xPendingReadyCoRoutineList ) == pdFALSE ) { CRCB_t* pxUnblockedCRCB; + /* The pending ready list can be accessed by an ISR. */ portDISABLE_INTERRUPTS(); { @@ -243,6 +211,7 @@ static void prvCheckPendingReadyList( void ) ( void ) uxListRemove( &( pxUnblockedCRCB->xEventListItem ) ); } portENABLE_INTERRUPTS(); + ( void ) uxListRemove( &( pxUnblockedCRCB->xGenericListItem ) ); prvAddCoRoutineToReadyQueue( pxUnblockedCRCB ); } @@ -252,6 +221,7 @@ static void prvCheckPendingReadyList( void ) static void prvCheckDelayedList( void ) { CRCB_t* pxCRCB; + xPassedTicks = xTaskGetTickCount() - xLastTickCount; while ( xPassedTicks ) @@ -263,6 +233,7 @@ static void prvCheckDelayedList( void ) if ( xCoRoutineTickCount == 0 ) { List_t* pxTemp; + /* Tick count has overflowed so we need to swap the delay lists. If there are any items in pxDelayedCoRoutineList here then there is an error! */ pxTemp = pxDelayedCoRoutineList; @@ -297,6 +268,7 @@ static void prvCheckDelayedList( void ) } } portENABLE_INTERRUPTS(); + prvAddCoRoutineToReadyQueue( pxCRCB ); } } @@ -309,6 +281,7 @@ void vCoRoutineSchedule( void ) { /* See if any co-routines readied by events need moving to the ready lists. */ prvCheckPendingReadyList(); + /* See if any delayed co-routines have timed out. */ prvCheckDelayedList(); @@ -327,8 +300,10 @@ void vCoRoutineSchedule( void ) /* listGET_OWNER_OF_NEXT_ENTRY walks through the list, so the co-routines of the same priority get an equal share of the processor time. */ listGET_OWNER_OF_NEXT_ENTRY( pxCurrentCoRoutine, &( pxReadyCoRoutineLists[ uxTopCoRoutineReadyPriority ] ) ); + /* Call the co-routine. */ ( pxCurrentCoRoutine->pxCoRoutineFunction )( pxCurrentCoRoutine, pxCurrentCoRoutine->uxIndex ); + return; } /*-----------------------------------------------------------*/ @@ -345,6 +320,7 @@ static void prvInitialiseCoRoutineLists( void ) vListInitialise( ( List_t* ) &xDelayedCoRoutineList1 ); vListInitialise( ( List_t* ) &xDelayedCoRoutineList2 ); vListInitialise( ( List_t* ) &xPendingReadyCoRoutineList ); + /* Start with pxDelayedCoRoutineList using list1 and the pxOverflowDelayedCoRoutineList using list2. */ pxDelayedCoRoutineList = &xDelayedCoRoutineList1; @@ -356,6 +332,7 @@ BaseType_t xCoRoutineRemoveFromEventList( const List_t* pxEventList ) { CRCB_t* pxUnblockedCRCB; BaseType_t xReturn; + /* This function is called from within an interrupt. It can only access event lists and the pending ready list. This function assumes that a check has already been made to ensure pxEventList is not empty. */ diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/event_groups.c b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/event_groups.c index b39e1387..dd626d61 100644 --- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/event_groups.c +++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/event_groups.c @@ -1,71 +1,29 @@ /* - FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd. - All rights reserved - - VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION. - - This file is part of the FreeRTOS distribution. - - FreeRTOS is free software; you can redistribute it and/or modify it under - the terms of the GNU General Public License (version 2) as published by the - Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception. - - *************************************************************************** - >>! NOTE: The modification to the GPL is included to allow you to !<< - >>! distribute a combined work that includes FreeRTOS without being !<< - >>! obliged to provide the source code for proprietary components !<< - >>! outside of the FreeRTOS kernel. !<< - *************************************************************************** - - FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY - WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS - FOR A PARTICULAR PURPOSE. Full license text is available on the following - link: http://www.freertos.org/a00114.html - - *************************************************************************** - * * - * FreeRTOS provides completely free yet professionally developed, * - * robust, strictly quality controlled, supported, and cross * - * platform software that is more than just the market leader, it * - * is the industry's de facto standard. * - * * - * Help yourself get started quickly while simultaneously helping * - * to support the FreeRTOS project by purchasing a FreeRTOS * - * tutorial book, reference manual, or both: * - * http://www.FreeRTOS.org/Documentation * - * * - *************************************************************************** - - http://www.FreeRTOS.org/FAQHelp.html - Having a problem? Start by reading - the FAQ page "My application does not run, what could be wrong?". Have you - defined configASSERT()? - - http://www.FreeRTOS.org/support - In return for receiving this top quality - embedded software for free we request you assist our global community by - participating in the support forum. - - http://www.FreeRTOS.org/training - Investing in training allows your team to - be as productive as possible as early as possible. Now you can receive - FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers - Ltd, and the world's leading authority on the world's leading RTOS. - - http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products, - including FreeRTOS+Trace - an indispensable productivity tool, a DOS - compatible FAT file system, and our tiny thread aware UDP/IP stack. - - http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate. - Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS. - - http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High - Integrity Systems ltd. to sell under the OpenRTOS brand. Low cost OpenRTOS - licenses offer ticketed support, indemnification and commercial middleware. - - http://www.SafeRTOS.com - High Integrity Systems also provide a safety - engineered and independently SIL3 certified version for use in safety and - mission critical applications that require provable dependability. - - 1 tab == 4 spaces! -*/ + * FreeRTOS Kernel V10.0.1 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ /* Standard includes. */ #include @@ -87,14 +45,6 @@ header files above, but not in this file, in order to generate the correct privileged Vs unprivileged linkage and placement. */ #undef MPU_WRAPPERS_INCLUDED_FROM_API_FILE /*lint !e961 !e750. */ -#if ( INCLUDE_xEventGroupSetBitFromISR == 1 ) && ( configUSE_TIMERS == 0 ) -#error configUSE_TIMERS must be set to 1 to make the xEventGroupSetBitFromISR() function available. -#endif - -#if ( INCLUDE_xEventGroupSetBitFromISR == 1 ) && ( INCLUDE_xTimerPendFunctionCall == 0 ) -#error INCLUDE_xTimerPendFunctionCall must also be set to one to make the xEventGroupSetBitFromISR() function available. -#endif - /* The following bit fields convey control information in a task's event list item value. It is important they don't clash with the taskEVENT_LIST_ITEM_VALUE_IN_USE definition. */ @@ -119,6 +69,9 @@ typedef struct xEventGroupDefinition UBaseType_t uxEventGroupNumber; #endif +#if( ( configSUPPORT_STATIC_ALLOCATION == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) ) + uint8_t ucStaticallyAllocated; /*< Set to pdTRUE if the event group is statically allocated to ensure no attempt is made to free the memory. */ +#endif } EventGroup_t; /*-----------------------------------------------------------*/ @@ -131,19 +84,82 @@ typedef struct xEventGroupDefinition * wait condition is met if any of the bits set in uxBitsToWait for are also set * in uxCurrentEventBits. */ -static BaseType_t prvTestWaitCondition( const EventBits_t uxCurrentEventBits, const EventBits_t uxBitsToWaitFor, const BaseType_t xWaitForAllBits ); +static BaseType_t prvTestWaitCondition( const EventBits_t uxCurrentEventBits, const EventBits_t uxBitsToWaitFor, const BaseType_t xWaitForAllBits ) PRIVILEGED_FUNCTION; /*-----------------------------------------------------------*/ +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) + +EventGroupHandle_t xEventGroupCreateStatic( StaticEventGroup_t* pxEventGroupBuffer ) +{ + EventGroup_t* pxEventBits; + + /* A StaticEventGroup_t object must be provided. */ + configASSERT( pxEventGroupBuffer ); + +#if( configASSERT_DEFINED == 1 ) + { + /* Sanity check that the size of the structure used to declare a + variable of type StaticEventGroup_t equals the size of the real + event group structure. */ + volatile size_t xSize = sizeof( StaticEventGroup_t ); + configASSERT( xSize == sizeof( EventGroup_t ) ); + } +#endif /* configASSERT_DEFINED */ + + /* The user has provided a statically allocated event group - use it. */ + pxEventBits = ( EventGroup_t* ) pxEventGroupBuffer; /*lint !e740 EventGroup_t and StaticEventGroup_t are guaranteed to have the same size and alignment requirement - checked by configASSERT(). */ + + if ( pxEventBits != NULL ) + { + pxEventBits->uxEventBits = 0; + vListInitialise( &( pxEventBits->xTasksWaitingForBits ) ); + +#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) + { + /* Both static and dynamic allocation can be used, so note that + this event group was created statically in case the event group + is later deleted. */ + pxEventBits->ucStaticallyAllocated = pdTRUE; + } +#endif /* configSUPPORT_DYNAMIC_ALLOCATION */ + + traceEVENT_GROUP_CREATE( pxEventBits ); + } + else + { + traceEVENT_GROUP_CREATE_FAILED(); + } + + return ( EventGroupHandle_t ) pxEventBits; +} + +#endif /* configSUPPORT_STATIC_ALLOCATION */ +/*-----------------------------------------------------------*/ + +#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) + EventGroupHandle_t xEventGroupCreate( void ) { EventGroup_t* pxEventBits; + + /* Allocate the event group. */ pxEventBits = ( EventGroup_t* ) pvPortMalloc( sizeof( EventGroup_t ) ); if ( pxEventBits != NULL ) { pxEventBits->uxEventBits = 0; vListInitialise( &( pxEventBits->xTasksWaitingForBits ) ); + +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) + { + /* Both static and dynamic allocation can be used, so note this + event group was allocated statically in case the event group is + later deleted. */ + pxEventBits->ucStaticallyAllocated = pdFALSE; + } +#endif /* configSUPPORT_STATIC_ALLOCATION */ + traceEVENT_GROUP_CREATE( pxEventBits ); } else @@ -153,6 +169,8 @@ EventGroupHandle_t xEventGroupCreate( void ) return ( EventGroupHandle_t ) pxEventBits; } + +#endif /* configSUPPORT_DYNAMIC_ALLOCATION */ /*-----------------------------------------------------------*/ EventBits_t xEventGroupSync( EventGroupHandle_t xEventGroup, const EventBits_t uxBitsToSet, const EventBits_t uxBitsToWaitFor, TickType_t xTicksToWait ) @@ -161,6 +179,7 @@ EventBits_t xEventGroupSync( EventGroupHandle_t xEventGroup, const EventBits_t u EventGroup_t* pxEventBits = ( EventGroup_t* ) xEventGroup; BaseType_t xAlreadyYielded; BaseType_t xTimeoutOccurred = pdFALSE; + configASSERT( ( uxBitsToWaitFor & eventEVENT_BITS_CONTROL_BYTES ) == 0 ); configASSERT( uxBitsToWaitFor != 0 ); #if ( ( INCLUDE_xTaskGetSchedulerState == 1 ) || ( configUSE_TIMERS == 1 ) ) @@ -168,18 +187,22 @@ EventBits_t xEventGroupSync( EventGroupHandle_t xEventGroup, const EventBits_t u configASSERT( !( ( xTaskGetSchedulerState() == taskSCHEDULER_SUSPENDED ) && ( xTicksToWait != 0 ) ) ); } #endif + vTaskSuspendAll(); { uxOriginalBitValue = pxEventBits->uxEventBits; + ( void ) xEventGroupSetBits( xEventGroup, uxBitsToSet ); if ( ( ( uxOriginalBitValue | uxBitsToSet ) & uxBitsToWaitFor ) == uxBitsToWaitFor ) { /* All the rendezvous bits are now set - no need to block. */ uxReturn = ( uxOriginalBitValue | uxBitsToSet ); + /* Rendezvous always clear the bits. They will have been cleared already unless this is the only task in the rendezvous. */ pxEventBits->uxEventBits &= ~uxBitsToWaitFor; + xTicksToWait = 0; } else @@ -187,10 +210,12 @@ EventBits_t xEventGroupSync( EventGroupHandle_t xEventGroup, const EventBits_t u if ( xTicksToWait != ( TickType_t ) 0 ) { traceEVENT_GROUP_SYNC_BLOCK( xEventGroup, uxBitsToSet, uxBitsToWaitFor ); + /* Store the bits that the calling task is waiting for in the task's event list item so the kernel knows when a match is found. Then enter the blocked state. */ vTaskPlaceOnUnorderedEventList( &( pxEventBits->xTasksWaitingForBits ), ( uxBitsToWaitFor | eventCLEAR_EVENTS_ON_EXIT_BIT | eventWAIT_FOR_ALL_BITS ), xTicksToWait ); + /* This assignment is obsolete as uxReturn will get set after the task unblocks, but some compilers mistakenly generate a warning about uxReturn being returned without being set if the @@ -202,6 +227,7 @@ EventBits_t xEventGroupSync( EventGroupHandle_t xEventGroup, const EventBits_t u /* The rendezvous bits were not set, but no block time was specified - just return the current event bit value. */ uxReturn = pxEventBits->uxEventBits; + xTimeoutOccurred = pdTRUE; } } } @@ -245,6 +271,7 @@ EventBits_t xEventGroupSync( EventGroupHandle_t xEventGroup, const EventBits_t u } } taskEXIT_CRITICAL(); + xTimeoutOccurred = pdTRUE; } else @@ -258,6 +285,10 @@ EventBits_t xEventGroupSync( EventGroupHandle_t xEventGroup, const EventBits_t u } traceEVENT_GROUP_SYNC_END( xEventGroup, uxBitsToSet, uxBitsToWaitFor, xTimeoutOccurred ); + + /* Prevent compiler warnings when trace macros are not used. */ + ( void ) xTimeoutOccurred; + return uxReturn; } /*-----------------------------------------------------------*/ @@ -268,6 +299,7 @@ EventBits_t xEventGroupWaitBits( EventGroupHandle_t xEventGroup, const EventBits EventBits_t uxReturn, uxControlBits = 0; BaseType_t xWaitConditionMet, xAlreadyYielded; BaseType_t xTimeoutOccurred = pdFALSE; + /* Check the user is not attempting to wait on the bits used by the kernel itself, and that at least one bit is being requested. */ configASSERT( xEventGroup ); @@ -278,9 +310,11 @@ EventBits_t xEventGroupWaitBits( EventGroupHandle_t xEventGroup, const EventBits configASSERT( !( ( xTaskGetSchedulerState() == taskSCHEDULER_SUSPENDED ) && ( xTicksToWait != 0 ) ) ); } #endif + vTaskSuspendAll(); { const EventBits_t uxCurrentEventBits = pxEventBits->uxEventBits; + /* Check to see if the wait condition is already met or not. */ xWaitConditionMet = prvTestWaitCondition( uxCurrentEventBits, uxBitsToWaitFor, xWaitForAllBits ); @@ -306,6 +340,7 @@ EventBits_t xEventGroupWaitBits( EventGroupHandle_t xEventGroup, const EventBits /* The wait condition has not been met, but no block time was specified, so just return the current value. */ uxReturn = uxCurrentEventBits; + xTimeoutOccurred = pdTRUE; } else { @@ -335,10 +370,12 @@ EventBits_t xEventGroupWaitBits( EventGroupHandle_t xEventGroup, const EventBits task's event list item so the kernel knows when a match is found. Then enter the blocked state. */ vTaskPlaceOnUnorderedEventList( &( pxEventBits->xTasksWaitingForBits ), ( uxBitsToWaitFor | uxControlBits ), xTicksToWait ); + /* This is obsolete as it will get set after the task unblocks, but some compilers mistakenly generate a warning about the variable being returned without being set if it is not done. */ uxReturn = 0; + traceEVENT_GROUP_WAIT_BITS_BLOCK( xEventGroup, uxBitsToWaitFor ); } } @@ -385,10 +422,10 @@ EventBits_t xEventGroupWaitBits( EventGroupHandle_t xEventGroup, const EventBits { mtCOVERAGE_TEST_MARKER(); } + + xTimeoutOccurred = pdTRUE; } taskEXIT_CRITICAL(); - /* Prevent compiler warnings when trace macros are not used. */ - xTimeoutOccurred = pdFALSE; } else { @@ -400,6 +437,10 @@ EventBits_t xEventGroupWaitBits( EventGroupHandle_t xEventGroup, const EventBits } traceEVENT_GROUP_WAIT_BITS_END( xEventGroup, uxBitsToWaitFor, xTimeoutOccurred ); + + /* Prevent compiler warnings when trace macros are not used. */ + ( void ) xTimeoutOccurred; + return uxReturn; } /*-----------------------------------------------------------*/ @@ -408,20 +449,25 @@ EventBits_t xEventGroupClearBits( EventGroupHandle_t xEventGroup, const EventBit { EventGroup_t* pxEventBits = ( EventGroup_t* ) xEventGroup; EventBits_t uxReturn; + /* Check the user is not attempting to clear the bits used by the kernel itself. */ configASSERT( xEventGroup ); configASSERT( ( uxBitsToClear & eventEVENT_BITS_CONTROL_BYTES ) == 0 ); + taskENTER_CRITICAL(); { traceEVENT_GROUP_CLEAR_BITS( xEventGroup, uxBitsToClear ); + /* The value returned is the event group value prior to the bits being cleared. */ uxReturn = pxEventBits->uxEventBits; + /* Clear the bits. */ pxEventBits->uxEventBits &= ~uxBitsToClear; } taskEXIT_CRITICAL(); + return uxReturn; } /*-----------------------------------------------------------*/ @@ -431,8 +477,10 @@ EventBits_t xEventGroupClearBits( EventGroupHandle_t xEventGroup, const EventBit BaseType_t xEventGroupClearBitsFromISR( EventGroupHandle_t xEventGroup, const EventBits_t uxBitsToClear ) { BaseType_t xReturn; + traceEVENT_GROUP_CLEAR_BITS_FROM_ISR( xEventGroup, uxBitsToClear ); xReturn = xTimerPendFunctionCallFromISR( vEventGroupClearBitsCallback, ( void* ) xEventGroup, ( uint32_t ) uxBitsToClear, NULL ); + return xReturn; } @@ -444,11 +492,13 @@ EventBits_t xEventGroupGetBitsFromISR( EventGroupHandle_t xEventGroup ) UBaseType_t uxSavedInterruptStatus; EventGroup_t* pxEventBits = ( EventGroup_t* ) xEventGroup; EventBits_t uxReturn; + uxSavedInterruptStatus = portSET_INTERRUPT_MASK_FROM_ISR(); { uxReturn = pxEventBits->uxEventBits; } portCLEAR_INTERRUPT_MASK_FROM_ISR( uxSavedInterruptStatus ); + return uxReturn; } /*-----------------------------------------------------------*/ @@ -461,16 +511,20 @@ EventBits_t xEventGroupSetBits( EventGroupHandle_t xEventGroup, const EventBits_ EventBits_t uxBitsToClear = 0, uxBitsWaitedFor, uxControlBits; EventGroup_t* pxEventBits = ( EventGroup_t* ) xEventGroup; BaseType_t xMatchFound = pdFALSE; + /* Check the user is not attempting to set the bits used by the kernel itself. */ configASSERT( xEventGroup ); configASSERT( ( uxBitsToSet & eventEVENT_BITS_CONTROL_BYTES ) == 0 ); + pxList = &( pxEventBits->xTasksWaitingForBits ); pxListEnd = listGET_END_MARKER( pxList ); /*lint !e826 !e740 The mini list structure is used as the list end to save RAM. This is checked and valid. */ vTaskSuspendAll(); { traceEVENT_GROUP_SET_BITS( xEventGroup, uxBitsToSet ); + pxListItem = listGET_HEAD_ENTRY( pxList ); + /* Set the bits. */ pxEventBits->uxEventBits |= uxBitsToSet; @@ -480,6 +534,7 @@ EventBits_t xEventGroupSetBits( EventGroupHandle_t xEventGroup, const EventBits_ pxNext = listGET_NEXT( pxListItem ); uxBitsWaitedFor = listGET_LIST_ITEM_VALUE( pxListItem ); xMatchFound = pdFALSE; + /* Split the bits waited for from the control bits. */ uxControlBits = uxBitsWaitedFor & eventEVENT_BITS_CONTROL_BYTES; uxBitsWaitedFor &= ~eventEVENT_BITS_CONTROL_BYTES; @@ -523,7 +578,7 @@ EventBits_t xEventGroupSetBits( EventGroupHandle_t xEventGroup, const EventBits_ eventUNBLOCKED_DUE_TO_BIT_SET bit is set so the task knows that is was unblocked due to its required bits matching, rather than because it timed out. */ - ( void ) xTaskRemoveFromUnorderedEventList( pxListItem, pxEventBits->uxEventBits | eventUNBLOCKED_DUE_TO_BIT_SET ); + vTaskRemoveFromUnorderedEventList( pxListItem, pxEventBits->uxEventBits | eventUNBLOCKED_DUE_TO_BIT_SET ); } /* Move onto the next list item. Note pxListItem->pxNext is not @@ -537,6 +592,7 @@ EventBits_t xEventGroupSetBits( EventGroupHandle_t xEventGroup, const EventBits_ pxEventBits->uxEventBits &= ~uxBitsToClear; } ( void ) xTaskResumeAll(); + return pxEventBits->uxEventBits; } /*-----------------------------------------------------------*/ @@ -545,6 +601,7 @@ void vEventGroupDelete( EventGroupHandle_t xEventGroup ) { EventGroup_t* pxEventBits = ( EventGroup_t* ) xEventGroup; const List_t* pxTasksWaitingForBits = &( pxEventBits->xTasksWaitingForBits ); + vTaskSuspendAll(); { traceEVENT_GROUP_DELETE( xEventGroup ); @@ -552,12 +609,31 @@ void vEventGroupDelete( EventGroupHandle_t xEventGroup ) while ( listCURRENT_LIST_LENGTH( pxTasksWaitingForBits ) > ( UBaseType_t ) 0 ) { /* Unblock the task, returning 0 as the event list is being deleted - and cannot therefore have any bits set. */ - configASSERT( pxTasksWaitingForBits->xListEnd.pxNext != ( ListItem_t* ) & ( pxTasksWaitingForBits->xListEnd ) ); - ( void ) xTaskRemoveFromUnorderedEventList( pxTasksWaitingForBits->xListEnd.pxNext, eventUNBLOCKED_DUE_TO_BIT_SET ); + and cannot therefore have any bits set. */ + configASSERT( pxTasksWaitingForBits->xListEnd.pxNext != ( const ListItem_t* ) & ( pxTasksWaitingForBits->xListEnd ) ); + vTaskRemoveFromUnorderedEventList( pxTasksWaitingForBits->xListEnd.pxNext, eventUNBLOCKED_DUE_TO_BIT_SET ); } - vPortFree( pxEventBits ); +#if( ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) && ( configSUPPORT_STATIC_ALLOCATION == 0 ) ) + { + /* The event group can only have been allocated dynamically - free + it again. */ + vPortFree( pxEventBits ); + } +#elif( ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) && ( configSUPPORT_STATIC_ALLOCATION == 1 ) ) + { + /* The event group could have been allocated statically or + dynamically, so check before attempting to free the memory. */ + if ( pxEventBits->ucStaticallyAllocated == ( uint8_t ) pdFALSE ) + { + vPortFree( pxEventBits ); + } + else + { + mtCOVERAGE_TEST_MARKER(); + } + } +#endif /* configSUPPORT_DYNAMIC_ALLOCATION */ } ( void ) xTaskResumeAll(); } @@ -619,8 +695,10 @@ static BaseType_t prvTestWaitCondition( const EventBits_t uxCurrentEventBits, co BaseType_t xEventGroupSetBitsFromISR( EventGroupHandle_t xEventGroup, const EventBits_t uxBitsToSet, BaseType_t* pxHigherPriorityTaskWoken ) { BaseType_t xReturn; + traceEVENT_GROUP_SET_BITS_FROM_ISR( xEventGroup, uxBitsToSet ); xReturn = xTimerPendFunctionCallFromISR( vEventGroupSetBitsCallback, ( void* ) xEventGroup, ( uint32_t ) uxBitsToSet, pxHigherPriorityTaskWoken ); + return xReturn; } @@ -646,5 +724,17 @@ UBaseType_t uxEventGroupGetNumber( void* xEventGroup ) return xReturn; } -#endif +#endif /* configUSE_TRACE_FACILITY */ +/*-----------------------------------------------------------*/ + +#if ( configUSE_TRACE_FACILITY == 1 ) + +void vEventGroupSetNumber( void* xEventGroup, UBaseType_t uxEventGroupNumber ) +{ + ( ( EventGroup_t* ) xEventGroup )->uxEventGroupNumber = uxEventGroupNumber; +} + +#endif /* configUSE_TRACE_FACILITY */ +/*-----------------------------------------------------------*/ + diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/FreeRTOS.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/FreeRTOS.h index ef7d8074..6baf4b57 100644 --- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/FreeRTOS.h +++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/FreeRTOS.h @@ -1,71 +1,29 @@ /* - FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd. - All rights reserved - - VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION. - - This file is part of the FreeRTOS distribution. - - FreeRTOS is free software; you can redistribute it and/or modify it under - the terms of the GNU General Public License (version 2) as published by the - Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception. - - *************************************************************************** - >>! NOTE: The modification to the GPL is included to allow you to !<< - >>! distribute a combined work that includes FreeRTOS without being !<< - >>! obliged to provide the source code for proprietary components !<< - >>! outside of the FreeRTOS kernel. !<< - *************************************************************************** - - FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY - WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS - FOR A PARTICULAR PURPOSE. Full license text is available on the following - link: http://www.freertos.org/a00114.html - - *************************************************************************** - * * - * FreeRTOS provides completely free yet professionally developed, * - * robust, strictly quality controlled, supported, and cross * - * platform software that is more than just the market leader, it * - * is the industry's de facto standard. * - * * - * Help yourself get started quickly while simultaneously helping * - * to support the FreeRTOS project by purchasing a FreeRTOS * - * tutorial book, reference manual, or both: * - * http://www.FreeRTOS.org/Documentation * - * * - *************************************************************************** - - http://www.FreeRTOS.org/FAQHelp.html - Having a problem? Start by reading - the FAQ page "My application does not run, what could be wrong?". Have you - defined configASSERT()? - - http://www.FreeRTOS.org/support - In return for receiving this top quality - embedded software for free we request you assist our global community by - participating in the support forum. - - http://www.FreeRTOS.org/training - Investing in training allows your team to - be as productive as possible as early as possible. Now you can receive - FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers - Ltd, and the world's leading authority on the world's leading RTOS. - - http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products, - including FreeRTOS+Trace - an indispensable productivity tool, a DOS - compatible FAT file system, and our tiny thread aware UDP/IP stack. - - http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate. - Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS. - - http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High - Integrity Systems ltd. to sell under the OpenRTOS brand. Low cost OpenRTOS - licenses offer ticketed support, indemnification and commercial middleware. - - http://www.SafeRTOS.com - High Integrity Systems also provide a safety - engineered and independently SIL3 certified version for use in safety and - mission critical applications that require provable dependability. - - 1 tab == 4 spaces! -*/ + * FreeRTOS Kernel V10.0.1 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ #ifndef INC_FREERTOS_H #define INC_FREERTOS_H @@ -103,6 +61,15 @@ extern "C" { /* Definitions specific to the port being used. */ #include "portable.h" +/* Must be defaulted before configUSE_NEWLIB_REENTRANT is used below. */ +#ifndef configUSE_NEWLIB_REENTRANT +#define configUSE_NEWLIB_REENTRANT 0 +#endif + +/* Required if struct _reent is used. */ +#if ( configUSE_NEWLIB_REENTRANT == 1 ) +#include +#endif /* * Check all the required application specific macros have been defined. * These macros are application specific and (as downloaded) are defined @@ -117,6 +84,10 @@ extern "C" { #error Missing definition: configMAX_PRIORITIES must be defined in FreeRTOSConfig.h. See the Configuration section of the FreeRTOS API documentation for details. #endif +#if configMAX_PRIORITIES < 1 +#error configMAX_PRIORITIES must be defined to be greater than or equal to 1. +#endif + #ifndef configUSE_PREEMPTION #error Missing definition: configUSE_PREEMPTION must be defined in FreeRTOSConfig.h as either 1 or 0. See the Configuration section of the FreeRTOS API documentation for details. #endif @@ -129,87 +100,98 @@ extern "C" { #error Missing definition: configUSE_TICK_HOOK must be defined in FreeRTOSConfig.h as either 1 or 0. See the Configuration section of the FreeRTOS API documentation for details. #endif +#ifndef configUSE_16_BIT_TICKS +#error Missing definition: configUSE_16_BIT_TICKS must be defined in FreeRTOSConfig.h as either 1 or 0. See the Configuration section of the FreeRTOS API documentation for details. +#endif + +#ifndef configUSE_CO_ROUTINES +#define configUSE_CO_ROUTINES 0 +#endif + #ifndef INCLUDE_vTaskPrioritySet -#error Missing definition: INCLUDE_vTaskPrioritySet must be defined in FreeRTOSConfig.h as either 1 or 0. See the Configuration section of the FreeRTOS API documentation for details. +#define INCLUDE_vTaskPrioritySet 0 #endif #ifndef INCLUDE_uxTaskPriorityGet -#error Missing definition: INCLUDE_uxTaskPriorityGet must be defined in FreeRTOSConfig.h as either 1 or 0. See the Configuration section of the FreeRTOS API documentation for details. +#define INCLUDE_uxTaskPriorityGet 0 #endif #ifndef INCLUDE_vTaskDelete -#error Missing definition: INCLUDE_vTaskDelete must be defined in FreeRTOSConfig.h as either 1 or 0. See the Configuration section of the FreeRTOS API documentation for details. +#define INCLUDE_vTaskDelete 0 #endif #ifndef INCLUDE_vTaskSuspend -#error Missing definition: INCLUDE_vTaskSuspend must be defined in FreeRTOSConfig.h as either 1 or 0. See the Configuration section of the FreeRTOS API documentation for details. +#define INCLUDE_vTaskSuspend 0 #endif #ifndef INCLUDE_vTaskDelayUntil -#error Missing definition: INCLUDE_vTaskDelayUntil must be defined in FreeRTOSConfig.h as either 1 or 0. See the Configuration section of the FreeRTOS API documentation for details. +#define INCLUDE_vTaskDelayUntil 0 #endif #ifndef INCLUDE_vTaskDelay -#error Missing definition: INCLUDE_vTaskDelay must be defined in FreeRTOSConfig.h as either 1 or 0. See the Configuration section of the FreeRTOS API documentation for details. +#define INCLUDE_vTaskDelay 0 #endif -#ifndef configUSE_16_BIT_TICKS -#error Missing definition: configUSE_16_BIT_TICKS must be defined in FreeRTOSConfig.h as either 1 or 0. See the Configuration section of the FreeRTOS API documentation for details. +#ifndef INCLUDE_xTaskGetIdleTaskHandle +#define INCLUDE_xTaskGetIdleTaskHandle 0 #endif -#ifndef configMAX_PRIORITIES -#error configMAX_PRIORITIES must be defined to be greater than or equal to 1. +#ifndef INCLUDE_xTaskAbortDelay +#define INCLUDE_xTaskAbortDelay 0 #endif -/* Configuration sanity check. */ -#if ( ( configUSE_RECURSIVE_MUTEXES == 1 ) && ( configUSE_MUTEXES != 1 ) ) -#error configUSE_MUTEXES must be set to 1 to use recursive mutexes +#ifndef INCLUDE_xQueueGetMutexHolder +#define INCLUDE_xQueueGetMutexHolder 0 #endif -#ifndef configUSE_CO_ROUTINES -#define configUSE_CO_ROUTINES 0 +#ifndef INCLUDE_xSemaphoreGetMutexHolder +#define INCLUDE_xSemaphoreGetMutexHolder INCLUDE_xQueueGetMutexHolder #endif -#if configUSE_CO_ROUTINES != 0 -#ifndef configMAX_CO_ROUTINE_PRIORITIES -#error configMAX_CO_ROUTINE_PRIORITIES must be greater than or equal to 1. +#ifndef INCLUDE_xTaskGetHandle +#define INCLUDE_xTaskGetHandle 0 #endif + +#ifndef INCLUDE_uxTaskGetStackHighWaterMark +#define INCLUDE_uxTaskGetStackHighWaterMark 0 #endif -#ifndef INCLUDE_xTaskGetIdleTaskHandle -#define INCLUDE_xTaskGetIdleTaskHandle 0 +#ifndef INCLUDE_eTaskGetState +#define INCLUDE_eTaskGetState 0 #endif -#ifndef INCLUDE_xTimerGetTimerDaemonTaskHandle -#define INCLUDE_xTimerGetTimerDaemonTaskHandle 0 +#ifndef INCLUDE_xTaskResumeFromISR +#define INCLUDE_xTaskResumeFromISR 1 #endif -#ifndef INCLUDE_xQueueGetMutexHolder -#define INCLUDE_xQueueGetMutexHolder 0 +#ifndef INCLUDE_xTimerPendFunctionCall +#define INCLUDE_xTimerPendFunctionCall 0 #endif -#ifndef INCLUDE_xSemaphoreGetMutexHolder -#define INCLUDE_xSemaphoreGetMutexHolder INCLUDE_xQueueGetMutexHolder +#ifndef INCLUDE_xTaskGetSchedulerState +#define INCLUDE_xTaskGetSchedulerState 0 #endif -#ifndef INCLUDE_pcTaskGetTaskName -#define INCLUDE_pcTaskGetTaskName 0 +#ifndef INCLUDE_xTaskGetCurrentTaskHandle +#define INCLUDE_xTaskGetCurrentTaskHandle 0 #endif -#ifndef configUSE_APPLICATION_TASK_TAG -#define configUSE_APPLICATION_TASK_TAG 0 +#if configUSE_CO_ROUTINES != 0 +#ifndef configMAX_CO_ROUTINE_PRIORITIES +#error configMAX_CO_ROUTINE_PRIORITIES must be greater than or equal to 1. +#endif #endif -#ifndef configNUM_THREAD_LOCAL_STORAGE_POINTERS -#define configNUM_THREAD_LOCAL_STORAGE_POINTERS 0 +#ifndef configUSE_DAEMON_TASK_STARTUP_HOOK +#define configUSE_DAEMON_TASK_STARTUP_HOOK 0 #endif -#ifndef INCLUDE_uxTaskGetStackHighWaterMark -#define INCLUDE_uxTaskGetStackHighWaterMark 0 +#ifndef configUSE_APPLICATION_TASK_TAG +#define configUSE_APPLICATION_TASK_TAG 0 #endif -#ifndef INCLUDE_eTaskGetState -#define INCLUDE_eTaskGetState 0 +#ifndef configNUM_THREAD_LOCAL_STORAGE_POINTERS +#define configNUM_THREAD_LOCAL_STORAGE_POINTERS 0 #endif #ifndef configUSE_RECURSIVE_MUTEXES @@ -248,18 +230,6 @@ extern "C" { #error configMAX_TASK_NAME_LEN must be set to a minimum of 1 in FreeRTOSConfig.h #endif -#ifndef INCLUDE_xTaskResumeFromISR -#define INCLUDE_xTaskResumeFromISR 1 -#endif - -#ifndef INCLUDE_xEventGroupSetBitFromISR -#define INCLUDE_xEventGroupSetBitFromISR 0 -#endif - -#ifndef INCLUDE_xTimerPendFunctionCall -#define INCLUDE_xTimerPendFunctionCall 0 -#endif - #ifndef configASSERT #define configASSERT( x ) #define configASSERT_DEFINED 0 @@ -284,15 +254,6 @@ extern "C" { #endif /* configUSE_TIMERS */ -#ifndef INCLUDE_xTaskGetSchedulerState -#define INCLUDE_xTaskGetSchedulerState 0 -#endif - -#ifndef INCLUDE_xTaskGetCurrentTaskHandle -#define INCLUDE_xTaskGetCurrentTaskHandle 0 -#endif - - #ifndef portSET_INTERRUPT_MASK_FROM_ISR #define portSET_INTERRUPT_MASK_FROM_ISR() 0 #endif @@ -320,6 +281,7 @@ extern "C" { #if ( configQUEUE_REGISTRY_SIZE < 1 ) #define vQueueAddToRegistry( xQueue, pcName ) #define vQueueUnregisterQueue( xQueue ) +#define pcQueueGetName( xQueue ) #endif #ifndef portPOINTER_SIZE_TYPE @@ -392,6 +354,14 @@ task that attempted the read. */ #define traceBLOCKING_ON_QUEUE_RECEIVE( pxQueue ) #endif +#ifndef traceBLOCKING_ON_QUEUE_PEEK +/* Task is about to block because it cannot read from a +queue/mutex/semaphore. pxQueue is a pointer to the queue/mutex/semaphore +upon which the read was attempted. pxCurrentTCB points to the TCB of the +task that attempted the read. */ +#define traceBLOCKING_ON_QUEUE_PEEK( pxQueue ) +#endif + #ifndef traceBLOCKING_ON_QUEUE_SEND /* Task is about to block because it cannot write to a queue/mutex/semaphore. pxQueue is a pointer to the queue/mutex/semaphore @@ -404,12 +374,24 @@ task that attempted the write. */ #define configCHECK_FOR_STACK_OVERFLOW 0 #endif +#ifndef configRECORD_STACK_HIGH_ADDRESS +#define configRECORD_STACK_HIGH_ADDRESS 0 +#endif + +#ifndef configINCLUDE_FREERTOS_TASK_C_ADDITIONS_H +#define configINCLUDE_FREERTOS_TASK_C_ADDITIONS_H 0 +#endif + /* The following event macros are embedded in the kernel API calls. */ #ifndef traceMOVED_TASK_TO_READY_STATE #define traceMOVED_TASK_TO_READY_STATE( pxTCB ) #endif +#ifndef tracePOST_MOVED_TASK_TO_READY_STATE +#define tracePOST_MOVED_TASK_TO_READY_STATE( pxTCB ) +#endif + #ifndef traceQUEUE_CREATE #define traceQUEUE_CREATE( pxNewQueue ) #endif @@ -466,6 +448,10 @@ task that attempted the write. */ #define traceQUEUE_PEEK( pxQueue ) #endif +#ifndef traceQUEUE_PEEK_FAILED +#define traceQUEUE_PEEK_FAILED( pxQueue ) +#endif + #ifndef traceQUEUE_PEEK_FROM_ISR #define traceQUEUE_PEEK_FROM_ISR( pxQueue ) #endif @@ -511,7 +497,7 @@ task that attempted the write. */ #endif #ifndef traceTASK_DELAY_UNTIL -#define traceTASK_DELAY_UNTIL() +#define traceTASK_DELAY_UNTIL( x ) #endif #ifndef traceTASK_DELAY @@ -650,6 +636,58 @@ task that attempted the write. */ #define traceTASK_NOTIFY_GIVE_FROM_ISR() #endif +#ifndef traceSTREAM_BUFFER_CREATE_FAILED +#define traceSTREAM_BUFFER_CREATE_FAILED( xIsMessageBuffer ) +#endif + +#ifndef traceSTREAM_BUFFER_CREATE_STATIC_FAILED +#define traceSTREAM_BUFFER_CREATE_STATIC_FAILED( xReturn, xIsMessageBuffer ) +#endif + +#ifndef traceSTREAM_BUFFER_CREATE +#define traceSTREAM_BUFFER_CREATE( pxStreamBuffer, xIsMessageBuffer ) +#endif + +#ifndef traceSTREAM_BUFFER_DELETE +#define traceSTREAM_BUFFER_DELETE( xStreamBuffer ) +#endif + +#ifndef traceSTREAM_BUFFER_RESET +#define traceSTREAM_BUFFER_RESET( xStreamBuffer ) +#endif + +#ifndef traceBLOCKING_ON_STREAM_BUFFER_SEND +#define traceBLOCKING_ON_STREAM_BUFFER_SEND( xStreamBuffer ) +#endif + +#ifndef traceSTREAM_BUFFER_SEND +#define traceSTREAM_BUFFER_SEND( xStreamBuffer, xBytesSent ) +#endif + +#ifndef traceSTREAM_BUFFER_SEND_FAILED +#define traceSTREAM_BUFFER_SEND_FAILED( xStreamBuffer ) +#endif + +#ifndef traceSTREAM_BUFFER_SEND_FROM_ISR +#define traceSTREAM_BUFFER_SEND_FROM_ISR( xStreamBuffer, xBytesSent ) +#endif + +#ifndef traceBLOCKING_ON_STREAM_BUFFER_RECEIVE +#define traceBLOCKING_ON_STREAM_BUFFER_RECEIVE( xStreamBuffer ) +#endif + +#ifndef traceSTREAM_BUFFER_RECEIVE +#define traceSTREAM_BUFFER_RECEIVE( xStreamBuffer, xReceivedLength ) +#endif + +#ifndef traceSTREAM_BUFFER_RECEIVE_FAILED +#define traceSTREAM_BUFFER_RECEIVE_FAILED( xStreamBuffer ) +#endif + +#ifndef traceSTREAM_BUFFER_RECEIVE_FROM_ISR +#define traceSTREAM_BUFFER_RECEIVE_FROM_ISR( xStreamBuffer, xReceivedLength ) +#endif + #ifndef configGENERATE_RUN_TIME_STATS #define configGENERATE_RUN_TIME_STATS 0 #endif @@ -684,14 +722,6 @@ task that attempted the write. */ #define portYIELD_WITHIN_API portYIELD #endif -#ifndef pvPortMallocAligned -#define pvPortMallocAligned( x, puxStackBuffer ) ( ( ( puxStackBuffer ) == NULL ) ? ( pvPortMalloc( ( x ) ) ) : ( puxStackBuffer ) ) -#endif - -#ifndef vPortFreeAligned -#define vPortFreeAligned( pvBlockToFree ) vPortFree( pvBlockToFree ) -#endif - #ifndef portSUPPRESS_TICKS_AND_SLEEP #define portSUPPRESS_TICKS_AND_SLEEP( xExpectedIdleTime ) #endif @@ -708,6 +738,10 @@ task that attempted the write. */ #define configUSE_TICKLESS_IDLE 0 #endif +#ifndef configPRE_SUPPRESS_TICKS_AND_SLEEP_PROCESSING +#define configPRE_SUPPRESS_TICKS_AND_SLEEP_PROCESSING( x ) +#endif + #ifndef configPRE_SLEEP_PROCESSING #define configPRE_SLEEP_PROCESSING( x ) #endif @@ -724,6 +758,10 @@ task that attempted the write. */ #define portTASK_USES_FLOATING_POINT() #endif +#ifndef portTASK_CALLS_SECURE_FUNCTIONS +#define portTASK_CALLS_SECURE_FUNCTIONS() +#endif + #ifndef configUSE_TIME_SLICING #define configUSE_TIME_SLICING 1 #endif @@ -732,10 +770,6 @@ task that attempted the write. */ #define configINCLUDE_APPLICATION_DEFINED_PRIVILEGED_FUNCTIONS 0 #endif -#ifndef configUSE_NEWLIB_REENTRANT -#define configUSE_NEWLIB_REENTRANT 0 -#endif - #ifndef configUSE_STATS_FORMATTING_FUNCTIONS #define configUSE_STATS_FORMATTING_FUNCTIONS 0 #endif @@ -776,6 +810,41 @@ task that attempted the write. */ #define portTICK_TYPE_IS_ATOMIC 0 #endif +#ifndef configSUPPORT_STATIC_ALLOCATION +/* Defaults to 0 for backward compatibility. */ +#define configSUPPORT_STATIC_ALLOCATION 0 +#endif + +#ifndef configSUPPORT_DYNAMIC_ALLOCATION +/* Defaults to 1 for backward compatibility. */ +#define configSUPPORT_DYNAMIC_ALLOCATION 1 +#endif + +#ifndef configSTACK_DEPTH_TYPE +/* Defaults to uint16_t for backward compatibility, but can be overridden +in FreeRTOSConfig.h if uint16_t is too restrictive. */ +#define configSTACK_DEPTH_TYPE uint16_t +#endif + +/* Sanity check the configuration. */ +#if( configUSE_TICKLESS_IDLE != 0 ) +#if( INCLUDE_vTaskSuspend != 1 ) +#error INCLUDE_vTaskSuspend must be set to 1 if configUSE_TICKLESS_IDLE is not set to 0 +#endif /* INCLUDE_vTaskSuspend */ +#endif /* configUSE_TICKLESS_IDLE */ + +#if( ( configSUPPORT_STATIC_ALLOCATION == 0 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 0 ) ) +#error configSUPPORT_STATIC_ALLOCATION and configSUPPORT_DYNAMIC_ALLOCATION cannot both be 0, but can both be 1. +#endif + +#if( ( configUSE_RECURSIVE_MUTEXES == 1 ) && ( configUSE_MUTEXES != 1 ) ) +#error configUSE_MUTEXES must be set to 1 to use recursive mutexes +#endif + +#ifndef configINITIAL_TICK_COUNT +#define configINITIAL_TICK_COUNT 0 +#endif + #if( portTICK_TYPE_IS_ATOMIC == 0 ) /* Either variables of tick type cannot be read atomically, or portTICK_TYPE_IS_ATOMIC was not set - map the critical sections used when @@ -799,6 +868,32 @@ V8 if desired. */ #define configENABLE_BACKWARD_COMPATIBILITY 1 #endif +#ifndef configPRINTF +/* configPRINTF() was not defined, so define it away to nothing. To use +configPRINTF() then define it as follows (where MyPrintFunction() is +provided by the application writer): + +void MyPrintFunction(const char *pcFormat, ... ); +#define configPRINTF( X ) MyPrintFunction X + +Then call like a standard printf() function, but placing brackets around +all parameters so they are passed as a single parameter. For example: +configPRINTF( ("Value = %d", MyVariable) ); */ +#define configPRINTF( X ) +#endif + +#ifndef configMAX +/* The application writer has not provided their own MAX macro, so define +the following generic implementation. */ +#define configMAX( a, b ) ( ( ( a ) > ( b ) ) ? ( a ) : ( b ) ) +#endif + +#ifndef configMIN +/* The application writer has not provided their own MAX macro, so define +the following generic implementation. */ +#define configMIN( a, b ) ( ( ( a ) < ( b ) ) ? ( a ) : ( b ) ) +#endif + #if configENABLE_BACKWARD_COMPATIBILITY == 1 #define eTaskStateGet eTaskGetState #define portTickType TickType_t @@ -815,6 +910,10 @@ V8 if desired. */ #define xCoRoutineHandle CoRoutineHandle_t #define pdTASK_HOOK_CODE TaskHookFunction_t #define portTICK_RATE_MS portTICK_PERIOD_MS +#define pcTaskGetTaskName pcTaskGetName +#define pcTimerGetTimerName pcTimerGetName +#define pcQueueGetQueueName pcQueueGetName +#define vTaskGetTaskInfo vTaskGetInfo /* Backward compatibility within the scheduler code only - these definitions are not really required but are included for completeness. */ @@ -824,6 +923,10 @@ are not really required but are included for completeness. */ #define xList List_t #endif /* configENABLE_BACKWARD_COMPATIBILITY */ +#if( configUSE_ALTERNATIVE_API != 0 ) +#error The alternative API was deprecated some time ago, and was removed in FreeRTOS V9.0 0 +#endif + /* Set configUSE_TASK_FPU_SUPPORT to 0 to omit floating point support even if floating point hardware is otherwise supported by the FreeRTOS port in use. This constant is not supported by all FreeRTOS ports that include floating @@ -832,6 +935,231 @@ point support. */ #define configUSE_TASK_FPU_SUPPORT 1 #endif +/* + * In line with software engineering best practice, FreeRTOS implements a strict + * data hiding policy, so the real structures used by FreeRTOS to maintain the + * state of tasks, queues, semaphores, etc. are not accessible to the application + * code. However, if the application writer wants to statically allocate such + * an object then the size of the object needs to be know. Dummy structures + * that are guaranteed to have the same size and alignment requirements of the + * real objects are used for this purpose. The dummy list and list item + * structures below are used for inclusion in such a dummy structure. + */ +struct xSTATIC_LIST_ITEM +{ + TickType_t xDummy1; + void* pvDummy2[ 4 ]; +}; +typedef struct xSTATIC_LIST_ITEM StaticListItem_t; + +/* See the comments above the struct xSTATIC_LIST_ITEM definition. */ +struct xSTATIC_MINI_LIST_ITEM +{ + TickType_t xDummy1; + void* pvDummy2[ 2 ]; +}; +typedef struct xSTATIC_MINI_LIST_ITEM StaticMiniListItem_t; + +/* See the comments above the struct xSTATIC_LIST_ITEM definition. */ +typedef struct xSTATIC_LIST +{ + UBaseType_t uxDummy1; + void* pvDummy2; + StaticMiniListItem_t xDummy3; +} StaticList_t; + +/* + * In line with software engineering best practice, especially when supplying a + * library that is likely to change in future versions, FreeRTOS implements a + * strict data hiding policy. This means the Task structure used internally by + * FreeRTOS is not accessible to application code. However, if the application + * writer wants to statically allocate the memory required to create a task then + * the size of the task object needs to be know. The StaticTask_t structure + * below is provided for this purpose. Its sizes and alignment requirements are + * guaranteed to match those of the genuine structure, no matter which + * architecture is being used, and no matter how the values in FreeRTOSConfig.h + * are set. Its contents are somewhat obfuscated in the hope users will + * recognise that it would be unwise to make direct use of the structure members. + */ +typedef struct xSTATIC_TCB +{ + void* pxDummy1; +#if ( portUSING_MPU_WRAPPERS == 1 ) + xMPU_SETTINGS xDummy2; +#endif + StaticListItem_t xDummy3[ 2 ]; + UBaseType_t uxDummy5; + void* pxDummy6; + uint8_t ucDummy7[ configMAX_TASK_NAME_LEN ]; +#if ( ( portSTACK_GROWTH > 0 ) || ( configRECORD_STACK_HIGH_ADDRESS == 1 ) ) + void* pxDummy8; +#endif +#if ( portCRITICAL_NESTING_IN_TCB == 1 ) + UBaseType_t uxDummy9; +#endif +#if ( configUSE_TRACE_FACILITY == 1 ) + UBaseType_t uxDummy10[ 2 ]; +#endif +#if ( configUSE_MUTEXES == 1 ) + UBaseType_t uxDummy12[ 2 ]; +#endif +#if ( configUSE_APPLICATION_TASK_TAG == 1 ) + void* pxDummy14; +#endif +#if( configNUM_THREAD_LOCAL_STORAGE_POINTERS > 0 ) + void* pvDummy15[ configNUM_THREAD_LOCAL_STORAGE_POINTERS ]; +#endif +#if ( configGENERATE_RUN_TIME_STATS == 1 ) + uint32_t ulDummy16; +#endif +#if ( configUSE_NEWLIB_REENTRANT == 1 ) + struct _reent xDummy17; +#endif +#if ( configUSE_TASK_NOTIFICATIONS == 1 ) + uint32_t ulDummy18; + uint8_t ucDummy19; +#endif +#if( ( ( configSUPPORT_STATIC_ALLOCATION == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) ) || ( portUSING_MPU_WRAPPERS == 1 ) ) + uint8_t uxDummy20; +#endif + +#if( INCLUDE_xTaskAbortDelay == 1 ) + uint8_t ucDummy21; +#endif + +} StaticTask_t; + +/* + * In line with software engineering best practice, especially when supplying a + * library that is likely to change in future versions, FreeRTOS implements a + * strict data hiding policy. This means the Queue structure used internally by + * FreeRTOS is not accessible to application code. However, if the application + * writer wants to statically allocate the memory required to create a queue + * then the size of the queue object needs to be know. The StaticQueue_t + * structure below is provided for this purpose. Its sizes and alignment + * requirements are guaranteed to match those of the genuine structure, no + * matter which architecture is being used, and no matter how the values in + * FreeRTOSConfig.h are set. Its contents are somewhat obfuscated in the hope + * users will recognise that it would be unwise to make direct use of the + * structure members. + */ +typedef struct xSTATIC_QUEUE +{ + void* pvDummy1[ 3 ]; + + union + { + void* pvDummy2; + UBaseType_t uxDummy2; + } u; + + StaticList_t xDummy3[ 2 ]; + UBaseType_t uxDummy4[ 3 ]; + uint8_t ucDummy5[ 2 ]; + +#if( ( configSUPPORT_STATIC_ALLOCATION == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) ) + uint8_t ucDummy6; +#endif + +#if ( configUSE_QUEUE_SETS == 1 ) + void* pvDummy7; +#endif + +#if ( configUSE_TRACE_FACILITY == 1 ) + UBaseType_t uxDummy8; + uint8_t ucDummy9; +#endif + +} StaticQueue_t; +typedef StaticQueue_t StaticSemaphore_t; + +/* + * In line with software engineering best practice, especially when supplying a + * library that is likely to change in future versions, FreeRTOS implements a + * strict data hiding policy. This means the event group structure used + * internally by FreeRTOS is not accessible to application code. However, if + * the application writer wants to statically allocate the memory required to + * create an event group then the size of the event group object needs to be + * know. The StaticEventGroup_t structure below is provided for this purpose. + * Its sizes and alignment requirements are guaranteed to match those of the + * genuine structure, no matter which architecture is being used, and no matter + * how the values in FreeRTOSConfig.h are set. Its contents are somewhat + * obfuscated in the hope users will recognise that it would be unwise to make + * direct use of the structure members. + */ +typedef struct xSTATIC_EVENT_GROUP +{ + TickType_t xDummy1; + StaticList_t xDummy2; + +#if( configUSE_TRACE_FACILITY == 1 ) + UBaseType_t uxDummy3; +#endif + +#if( ( configSUPPORT_STATIC_ALLOCATION == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) ) + uint8_t ucDummy4; +#endif + +} StaticEventGroup_t; + +/* + * In line with software engineering best practice, especially when supplying a + * library that is likely to change in future versions, FreeRTOS implements a + * strict data hiding policy. This means the software timer structure used + * internally by FreeRTOS is not accessible to application code. However, if + * the application writer wants to statically allocate the memory required to + * create a software timer then the size of the queue object needs to be know. + * The StaticTimer_t structure below is provided for this purpose. Its sizes + * and alignment requirements are guaranteed to match those of the genuine + * structure, no matter which architecture is being used, and no matter how the + * values in FreeRTOSConfig.h are set. Its contents are somewhat obfuscated in + * the hope users will recognise that it would be unwise to make direct use of + * the structure members. + */ +typedef struct xSTATIC_TIMER +{ + void* pvDummy1; + StaticListItem_t xDummy2; + TickType_t xDummy3; + UBaseType_t uxDummy4; + void* pvDummy5[ 2 ]; +#if( configUSE_TRACE_FACILITY == 1 ) + UBaseType_t uxDummy6; +#endif + +#if( ( configSUPPORT_STATIC_ALLOCATION == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) ) + uint8_t ucDummy7; +#endif + +} StaticTimer_t; + +/* +* In line with software engineering best practice, especially when supplying a +* library that is likely to change in future versions, FreeRTOS implements a +* strict data hiding policy. This means the stream buffer structure used +* internally by FreeRTOS is not accessible to application code. However, if +* the application writer wants to statically allocate the memory required to +* create a stream buffer then the size of the stream buffer object needs to be +* know. The StaticStreamBuffer_t structure below is provided for this purpose. +* Its size and alignment requirements are guaranteed to match those of the +* genuine structure, no matter which architecture is being used, and no matter +* how the values in FreeRTOSConfig.h are set. Its contents are somewhat +* obfuscated in the hope users will recognise that it would be unwise to make +* direct use of the structure members. +*/ +typedef struct xSTATIC_STREAM_BUFFER +{ + size_t uxDummy1[ 4 ]; + void* pvDummy2[ 3 ]; + uint8_t ucDummy3; +#if ( configUSE_TRACE_FACILITY == 1 ) + UBaseType_t uxDummy4; +#endif +} StaticStreamBuffer_t; + +/* Message buffers are built on stream buffers. */ +typedef StaticStreamBuffer_t StaticMessageBuffer_t; + #ifdef __cplusplus } #endif diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/FreeRTOSConfig_template.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/FreeRTOSConfig_template.h deleted file mode 100644 index 421681ba..00000000 --- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/FreeRTOSConfig_template.h +++ /dev/null @@ -1,173 +0,0 @@ -/* - FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd. - All rights reserved - - VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION. - - This file is part of the FreeRTOS distribution. - - FreeRTOS is free software; you can redistribute it and/or modify it under - the terms of the GNU General Public License (version 2) as published by the - Free Software Foundation >>!AND MODIFIED BY!<< the FreeRTOS exception. - - *************************************************************************** - >>! NOTE: The modification to the GPL is included to allow you to !<< - >>! distribute a combined work that includes FreeRTOS without being !<< - >>! obliged to provide the source code for proprietary components !<< - >>! outside of the FreeRTOS kernel. !<< - *************************************************************************** - - FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY - WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS - FOR A PARTICULAR PURPOSE. Full license text is available on the following - link: http://www.freertos.org/a00114.html - - *************************************************************************** - * * - * FreeRTOS provides completely free yet professionally developed, * - * robust, strictly quality controlled, supported, and cross * - * platform software that is more than just the market leader, it * - * is the industry's de facto standard. * - * * - * Help yourself get started quickly while simultaneously helping * - * to support the FreeRTOS project by purchasing a FreeRTOS * - * tutorial book, reference manual, or both: * - * http://www.FreeRTOS.org/Documentation * - * * - *************************************************************************** - - http://www.FreeRTOS.org/FAQHelp.html - Having a problem? Start by reading - the FAQ page "My application does not run, what could be wrong?". Have you - defined configASSERT()? - - http://www.FreeRTOS.org/support - In return for receiving this top quality - embedded software for free we request you assist our global community by - participating in the support forum. - - http://www.FreeRTOS.org/training - Investing in training allows your team to - be as productive as possible as early as possible. Now you can receive - FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers - Ltd, and the world's leading authority on the world's leading RTOS. - - http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products, - including FreeRTOS+Trace - an indispensable productivity tool, a DOS - compatible FAT file system, and our tiny thread aware UDP/IP stack. - - http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate. - Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS. - - http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High - Integrity Systems ltd. to sell under the OpenRTOS brand. Low cost OpenRTOS - licenses offer ticketed support, indemnification and commercial middleware. - - http://www.SafeRTOS.com - High Integrity Systems also provide a safety - engineered and independently SIL3 certified version for use in safety and - mission critical applications that require provable dependability. - - 1 tab == 4 spaces! -*/ - - -#ifndef FREERTOS_CONFIG_H -#define FREERTOS_CONFIG_H - -/*----------------------------------------------------------- - * Application specific definitions. - * - * These definitions should be adjusted for your particular hardware and - * application requirements. - * - * THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE - * FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE. - * - * See http://www.freertos.org/a00110.html. - *----------------------------------------------------------*/ - -/* Ensure stdint is only used by the compiler, and not the assembler. */ -#if defined(__ICCARM__) || defined(__CC_ARM) || defined(__GNUC__) -#include -extern uint32_t SystemCoreClock; -#endif - -#define configUSE_PREEMPTION 1 -#define configUSE_IDLE_HOOK 0 -#define configUSE_TICK_HOOK 0 -#define configCPU_CLOCK_HZ (SystemCoreClock) -#define configTICK_RATE_HZ ((TickType_t)1000) -#define configMAX_PRIORITIES (7) -#define configMINIMAL_STACK_SIZE ((uint16_t)128) -#define configTOTAL_HEAP_SIZE ((size_t)(15 * 1024)) -#define configMAX_TASK_NAME_LEN (16) -#define configUSE_TRACE_FACILITY 1 -#define configUSE_16_BIT_TICKS 0 -#define configIDLE_SHOULD_YIELD 1 -#define configUSE_MUTEXES 1 -#define configQUEUE_REGISTRY_SIZE 8 -#define configCHECK_FOR_STACK_OVERFLOW 0 -#define configUSE_RECURSIVE_MUTEXES 1 -#define configUSE_MALLOC_FAILED_HOOK 0 -#define configUSE_APPLICATION_TASK_TAG 0 -#define configUSE_COUNTING_SEMAPHORES 1 -#define configGENERATE_RUN_TIME_STATS 0 - -/* Co-routine definitions. */ -#define configUSE_CO_ROUTINES 0 -#define configMAX_CO_ROUTINE_PRIORITIES (2) - -/* Software timer definitions. */ -#define configUSE_TIMERS 0 -#define configTIMER_TASK_PRIORITY (2) -#define configTIMER_QUEUE_LENGTH 10 -#define configTIMER_TASK_STACK_DEPTH (configMINIMAL_STACK_SIZE * 2) - -/* Set the following definitions to 1 to include the API function, or zero -to exclude the API function. */ -#define INCLUDE_vTaskPrioritySet 1 -#define INCLUDE_uxTaskPriorityGet 1 -#define INCLUDE_vTaskDelete 1 -#define INCLUDE_vTaskCleanUpResources 0 -#define INCLUDE_vTaskSuspend 1 -#define INCLUDE_vTaskDelayUntil 0 -#define INCLUDE_vTaskDelay 1 -#define INCLUDE_xTaskGetSchedulerState 1 - -/* Cortex-M specific definitions. */ -#ifdef __NVIC_PRIO_BITS -/* __BVIC_PRIO_BITS will be specified when CMSIS is being used. */ -#define configPRIO_BITS __NVIC_PRIO_BITS -#else -#define configPRIO_BITS 4 /* 15 priority levels */ -#endif - -/* The lowest interrupt priority that can be used in a call to a "set priority" -function. */ -#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY 0xf - -/* The highest interrupt priority that can be used by any interrupt service -routine that makes calls to interrupt safe FreeRTOS API functions. DO NOT CALL -INTERRUPT SAFE FREERTOS API FUNCTIONS FROM ANY INTERRUPT THAT HAS A HIGHER -PRIORITY THAN THIS! (higher priorities are lower numeric values. */ -#define configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY 5 - -/* Interrupt priorities used by the kernel port layer itself. These are generic -to all Cortex-M ports, and do not rely on any particular library functions. */ -#define configKERNEL_INTERRUPT_PRIORITY ( configLIBRARY_LOWEST_INTERRUPT_PRIORITY << (8 - configPRIO_BITS) ) -/* !!!! configMAX_SYSCALL_INTERRUPT_PRIORITY must not be set to zero !!!! -See http://www.FreeRTOS.org/RTOS-Cortex-M3-M4.html. */ -#define configMAX_SYSCALL_INTERRUPT_PRIORITY ( configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY << (8 - configPRIO_BITS) ) - -/* Normal assert() semantics without relying on the provision of an assert.h -header file. */ -#define configASSERT( x ) if( ( x ) == 0 ) { taskDISABLE_INTERRUPTS(); for( ;; ); } - -/* Definitions that map the FreeRTOS port interrupt handlers to their CMSIS - standard names. */ -#define vPortSVCHandler SVC_Handler -#define xPortPendSVHandler PendSV_Handler - -/* IMPORTANT: This define MUST be commented when used with STM32Cube firmware, - to prevent overwriting SysTick_Handler defined within STM32Cube HAL */ -/* #define xPortSysTickHandler SysTick_Handler */ - -#endif /* FREERTOS_CONFIG_H */ - diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/StackMacros.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/StackMacros.h index d2835ebf..be30bb55 100644 --- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/StackMacros.h +++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/StackMacros.h @@ -1,75 +1,37 @@ /* - FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd. - All rights reserved - - VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION. - - This file is part of the FreeRTOS distribution. - - FreeRTOS is free software; you can redistribute it and/or modify it under - the terms of the GNU General Public License (version 2) as published by the - Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception. - - *************************************************************************** - >>! NOTE: The modification to the GPL is included to allow you to !<< - >>! distribute a combined work that includes FreeRTOS without being !<< - >>! obliged to provide the source code for proprietary components !<< - >>! outside of the FreeRTOS kernel. !<< - *************************************************************************** - - FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY - WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS - FOR A PARTICULAR PURPOSE. Full license text is available on the following - link: http://www.freertos.org/a00114.html - - *************************************************************************** - * * - * FreeRTOS provides completely free yet professionally developed, * - * robust, strictly quality controlled, supported, and cross * - * platform software that is more than just the market leader, it * - * is the industry's de facto standard. * - * * - * Help yourself get started quickly while simultaneously helping * - * to support the FreeRTOS project by purchasing a FreeRTOS * - * tutorial book, reference manual, or both: * - * http://www.FreeRTOS.org/Documentation * - * * - *************************************************************************** - - http://www.FreeRTOS.org/FAQHelp.html - Having a problem? Start by reading - the FAQ page "My application does not run, what could be wrong?". Have you - defined configASSERT()? - - http://www.FreeRTOS.org/support - In return for receiving this top quality - embedded software for free we request you assist our global community by - participating in the support forum. - - http://www.FreeRTOS.org/training - Investing in training allows your team to - be as productive as possible as early as possible. Now you can receive - FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers - Ltd, and the world's leading authority on the world's leading RTOS. - - http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products, - including FreeRTOS+Trace - an indispensable productivity tool, a DOS - compatible FAT file system, and our tiny thread aware UDP/IP stack. - - http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate. - Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS. - - http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High - Integrity Systems ltd. to sell under the OpenRTOS brand. Low cost OpenRTOS - licenses offer ticketed support, indemnification and commercial middleware. - - http://www.SafeRTOS.com - High Integrity Systems also provide a safety - engineered and independently SIL3 certified version for use in safety and - mission critical applications that require provable dependability. - - 1 tab == 4 spaces! -*/ + * FreeRTOS Kernel V10.0.1 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ #ifndef STACK_MACROS_H #define STACK_MACROS_H +#ifndef _MSC_VER /* Visual Studio doesn't support #warning. */ +#warning The name of this file has changed to stack_macros.h. Please update your code accordingly. This source file (which has the original name) will be removed in future released. +#endif + /* * Call the stack overflow hook function if the stack of the task being swapped * out is currently overflowed, or looks like it might have overflowed in the diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/croutine.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/croutine.h index 9802d6db..7a7729c4 100644 --- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/croutine.h +++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/croutine.h @@ -1,71 +1,29 @@ /* - FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd. - All rights reserved - - VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION. - - This file is part of the FreeRTOS distribution. - - FreeRTOS is free software; you can redistribute it and/or modify it under - the terms of the GNU General Public License (version 2) as published by the - Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception. - - *************************************************************************** - >>! NOTE: The modification to the GPL is included to allow you to !<< - >>! distribute a combined work that includes FreeRTOS without being !<< - >>! obliged to provide the source code for proprietary components !<< - >>! outside of the FreeRTOS kernel. !<< - *************************************************************************** - - FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY - WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS - FOR A PARTICULAR PURPOSE. Full license text is available on the following - link: http://www.freertos.org/a00114.html - - *************************************************************************** - * * - * FreeRTOS provides completely free yet professionally developed, * - * robust, strictly quality controlled, supported, and cross * - * platform software that is more than just the market leader, it * - * is the industry's de facto standard. * - * * - * Help yourself get started quickly while simultaneously helping * - * to support the FreeRTOS project by purchasing a FreeRTOS * - * tutorial book, reference manual, or both: * - * http://www.FreeRTOS.org/Documentation * - * * - *************************************************************************** - - http://www.FreeRTOS.org/FAQHelp.html - Having a problem? Start by reading - the FAQ page "My application does not run, what could be wrong?". Have you - defined configASSERT()? - - http://www.FreeRTOS.org/support - In return for receiving this top quality - embedded software for free we request you assist our global community by - participating in the support forum. - - http://www.FreeRTOS.org/training - Investing in training allows your team to - be as productive as possible as early as possible. Now you can receive - FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers - Ltd, and the world's leading authority on the world's leading RTOS. - - http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products, - including FreeRTOS+Trace - an indispensable productivity tool, a DOS - compatible FAT file system, and our tiny thread aware UDP/IP stack. - - http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate. - Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS. - - http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High - Integrity Systems ltd. to sell under the OpenRTOS brand. Low cost OpenRTOS - licenses offer ticketed support, indemnification and commercial middleware. - - http://www.SafeRTOS.com - High Integrity Systems also provide a safety - engineered and independently SIL3 certified version for use in safety and - mission critical applications that require provable dependability. - - 1 tab == 4 spaces! -*/ + * FreeRTOS Kernel V10.0.1 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ #ifndef CO_ROUTINE_H #define CO_ROUTINE_H diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/deprecated_definitions.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/deprecated_definitions.h index e1c5f7cc..0100cc4e 100644 --- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/deprecated_definitions.h +++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/deprecated_definitions.h @@ -1,71 +1,29 @@ /* - FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd. - All rights reserved - - VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION. - - This file is part of the FreeRTOS distribution. - - FreeRTOS is free software; you can redistribute it and/or modify it under - the terms of the GNU General Public License (version 2) as published by the - Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception. - - *************************************************************************** - >>! NOTE: The modification to the GPL is included to allow you to !<< - >>! distribute a combined work that includes FreeRTOS without being !<< - >>! obliged to provide the source code for proprietary components !<< - >>! outside of the FreeRTOS kernel. !<< - *************************************************************************** - - FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY - WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS - FOR A PARTICULAR PURPOSE. Full license text is available on the following - link: http://www.freertos.org/a00114.html - - *************************************************************************** - * * - * FreeRTOS provides completely free yet professionally developed, * - * robust, strictly quality controlled, supported, and cross * - * platform software that is more than just the market leader, it * - * is the industry's de facto standard. * - * * - * Help yourself get started quickly while simultaneously helping * - * to support the FreeRTOS project by purchasing a FreeRTOS * - * tutorial book, reference manual, or both: * - * http://www.FreeRTOS.org/Documentation * - * * - *************************************************************************** - - http://www.FreeRTOS.org/FAQHelp.html - Having a problem? Start by reading - the FAQ page "My application does not run, what could be wrong?". Have you - defined configASSERT()? - - http://www.FreeRTOS.org/support - In return for receiving this top quality - embedded software for free we request you assist our global community by - participating in the support forum. - - http://www.FreeRTOS.org/training - Investing in training allows your team to - be as productive as possible as early as possible. Now you can receive - FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers - Ltd, and the world's leading authority on the world's leading RTOS. - - http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products, - including FreeRTOS+Trace - an indispensable productivity tool, a DOS - compatible FAT file system, and our tiny thread aware UDP/IP stack. - - http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate. - Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS. - - http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High - Integrity Systems ltd. to sell under the OpenRTOS brand. Low cost OpenRTOS - licenses offer ticketed support, indemnification and commercial middleware. - - http://www.SafeRTOS.com - High Integrity Systems also provide a safety - engineered and independently SIL3 certified version for use in safety and - mission critical applications that require provable dependability. - - 1 tab == 4 spaces! -*/ + * FreeRTOS Kernel V10.0.1 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ #ifndef DEPRECATED_DEFINITIONS_H #define DEPRECATED_DEFINITIONS_H diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/event_groups.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/event_groups.h index 39afddb1..4f0da2f7 100644 --- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/event_groups.h +++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/event_groups.h @@ -1,71 +1,29 @@ /* - FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd. - All rights reserved - - VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION. - - This file is part of the FreeRTOS distribution. - - FreeRTOS is free software; you can redistribute it and/or modify it under - the terms of the GNU General Public License (version 2) as published by the - Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception. - - *************************************************************************** - >>! NOTE: The modification to the GPL is included to allow you to !<< - >>! distribute a combined work that includes FreeRTOS without being !<< - >>! obliged to provide the source code for proprietary components !<< - >>! outside of the FreeRTOS kernel. !<< - *************************************************************************** - - FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY - WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS - FOR A PARTICULAR PURPOSE. Full license text is available on the following - link: http://www.freertos.org/a00114.html - - *************************************************************************** - * * - * FreeRTOS provides completely free yet professionally developed, * - * robust, strictly quality controlled, supported, and cross * - * platform software that is more than just the market leader, it * - * is the industry's de facto standard. * - * * - * Help yourself get started quickly while simultaneously helping * - * to support the FreeRTOS project by purchasing a FreeRTOS * - * tutorial book, reference manual, or both: * - * http://www.FreeRTOS.org/Documentation * - * * - *************************************************************************** - - http://www.FreeRTOS.org/FAQHelp.html - Having a problem? Start by reading - the FAQ page "My application does not run, what could be wrong?". Have you - defined configASSERT()? - - http://www.FreeRTOS.org/support - In return for receiving this top quality - embedded software for free we request you assist our global community by - participating in the support forum. - - http://www.FreeRTOS.org/training - Investing in training allows your team to - be as productive as possible as early as possible. Now you can receive - FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers - Ltd, and the world's leading authority on the world's leading RTOS. - - http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products, - including FreeRTOS+Trace - an indispensable productivity tool, a DOS - compatible FAT file system, and our tiny thread aware UDP/IP stack. - - http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate. - Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS. - - http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High - Integrity Systems ltd. to sell under the OpenRTOS brand. Low cost OpenRTOS - licenses offer ticketed support, indemnification and commercial middleware. - - http://www.SafeRTOS.com - High Integrity Systems also provide a safety - engineered and independently SIL3 certified version for use in safety and - mission critical applications that require provable dependability. - - 1 tab == 4 spaces! -*/ + * FreeRTOS Kernel V10.0.1 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ #ifndef EVENT_GROUPS_H #define EVENT_GROUPS_H @@ -74,6 +32,7 @@ #error "include FreeRTOS.h" must appear in source files before "include event_groups.h" #endif +/* FreeRTOS includes. */ #include "timers.h" #ifdef __cplusplus @@ -137,7 +96,17 @@ typedef TickType_t EventBits_t; EventGroupHandle_t xEventGroupCreate( void ); * - * Create a new event group. This function cannot be called from an interrupt. + * Create a new event group. + * + * Internally, within the FreeRTOS implementation, event groups use a [small] + * block of memory, in which the event group's structure is stored. If an event + * groups is created using xEventGropuCreate() then the required memory is + * automatically dynamically allocated inside the xEventGroupCreate() function. + * (see http://www.freertos.org/a00111.html). If an event group is created + * using xEventGropuCreateStatic() then the application writer must instead + * provide the memory that will get used by the event group. + * xEventGroupCreateStatic() therefore allows an event group to be created + * without using any dynamic memory allocation. * * Although event groups are not related to ticks, for internal implementation * reasons the number of bits available for use in an event group is dependent @@ -173,7 +142,62 @@ typedef TickType_t EventBits_t; * \defgroup xEventGroupCreate xEventGroupCreate * \ingroup EventGroup */ +#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) EventGroupHandle_t xEventGroupCreate( void ) PRIVILEGED_FUNCTION; +#endif + +/** + * event_groups.h + *
+ EventGroupHandle_t xEventGroupCreateStatic( EventGroupHandle_t * pxEventGroupBuffer );
+
+ * + * Create a new event group. + * + * Internally, within the FreeRTOS implementation, event groups use a [small] + * block of memory, in which the event group's structure is stored. If an event + * groups is created using xEventGropuCreate() then the required memory is + * automatically dynamically allocated inside the xEventGroupCreate() function. + * (see http://www.freertos.org/a00111.html). If an event group is created + * using xEventGropuCreateStatic() then the application writer must instead + * provide the memory that will get used by the event group. + * xEventGroupCreateStatic() therefore allows an event group to be created + * without using any dynamic memory allocation. + * + * Although event groups are not related to ticks, for internal implementation + * reasons the number of bits available for use in an event group is dependent + * on the configUSE_16_BIT_TICKS setting in FreeRTOSConfig.h. If + * configUSE_16_BIT_TICKS is 1 then each event group contains 8 usable bits (bit + * 0 to bit 7). If configUSE_16_BIT_TICKS is set to 0 then each event group has + * 24 usable bits (bit 0 to bit 23). The EventBits_t type is used to store + * event bits within an event group. + * + * @param pxEventGroupBuffer pxEventGroupBuffer must point to a variable of type + * StaticEventGroup_t, which will be then be used to hold the event group's data + * structures, removing the need for the memory to be allocated dynamically. + * + * @return If the event group was created then a handle to the event group is + * returned. If pxEventGroupBuffer was NULL then NULL is returned. + * + * Example usage: + 
+	// StaticEventGroup_t is a publicly accessible structure that has the same
+	// size and alignment requirements as the real event group structure.  It is
+	// provided as a mechanism for applications to know the size of the event
+	// group (which is dependent on the architecture and configuration file
+	// settings) without breaking the strict data hiding policy by exposing the
+	// real event group internals.  This StaticEventGroup_t variable is passed
+	// into the xSemaphoreCreateEventGroupStatic() function and is used to store
+	// the event group's data structures
+	StaticEventGroup_t xEventGroupBuffer;
+
+	// Create the event group without dynamically allocating any memory.
+	xEventGroup = xEventGroupCreateStatic( &xEventGroupBuffer );
+
+ */ +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) +EventGroupHandle_t xEventGroupCreateStatic( StaticEventGroup_t* pxEventGroupBuffer ) PRIVILEGED_FUNCTION; +#endif /** * event_groups.h @@ -376,7 +400,7 @@ EventBits_t xEventGroupClearBits( EventGroupHandle_t xEventGroup, const EventBit } } - * \defgroup xEventGroupSetBitsFromISR xEventGroupSetBitsFromISR + * \defgroup xEventGroupClearBitsFromISR xEventGroupClearBitsFromISR * \ingroup EventGroup */ #if( configUSE_TRACE_FACILITY == 1 ) @@ -470,7 +494,7 @@ EventBits_t xEventGroupSetBits( EventGroupHandle_t xEventGroup, const EventBits_ * Setting bits in an event group is not a deterministic operation because there * are an unknown number of tasks that may be waiting for the bit or bits being * set. FreeRTOS does not allow nondeterministic operations to be performed in - * interrupts or from critical sections. Therefore xEventGroupSetBitFromISR() + * interrupts or from critical sections. Therefore xEventGroupSetBitsFromISR() * sends a message to the timer task to have the set operation performed in the * context of the timer task - where a scheduler lock is used in place of a * critical section. @@ -717,8 +741,10 @@ void vEventGroupDelete( EventGroupHandle_t xEventGroup ) PRIVILEGED_FUNCTION; void vEventGroupSetBitsCallback( void* pvEventGroup, const uint32_t ulBitsToSet ) PRIVILEGED_FUNCTION; void vEventGroupClearBitsCallback( void* pvEventGroup, const uint32_t ulBitsToClear ) PRIVILEGED_FUNCTION; + #if (configUSE_TRACE_FACILITY == 1) UBaseType_t uxEventGroupGetNumber( void* xEventGroup ) PRIVILEGED_FUNCTION; +void vEventGroupSetNumber( void* xEventGroup, UBaseType_t uxEventGroupNumber ) PRIVILEGED_FUNCTION; #endif #ifdef __cplusplus diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/list.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/list.h index 6511d215..6e3fca39 100644 --- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/list.h +++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/list.h @@ -1,71 +1,29 @@ /* - FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd. - All rights reserved - - VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION. - - This file is part of the FreeRTOS distribution. - - FreeRTOS is free software; you can redistribute it and/or modify it under - the terms of the GNU General Public License (version 2) as published by the - Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception. - - *************************************************************************** - >>! NOTE: The modification to the GPL is included to allow you to !<< - >>! distribute a combined work that includes FreeRTOS without being !<< - >>! obliged to provide the source code for proprietary components !<< - >>! outside of the FreeRTOS kernel. !<< - *************************************************************************** - - FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY - WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS - FOR A PARTICULAR PURPOSE. Full license text is available on the following - link: http://www.freertos.org/a00114.html - - *************************************************************************** - * * - * FreeRTOS provides completely free yet professionally developed, * - * robust, strictly quality controlled, supported, and cross * - * platform software that is more than just the market leader, it * - * is the industry's de facto standard. * - * * - * Help yourself get started quickly while simultaneously helping * - * to support the FreeRTOS project by purchasing a FreeRTOS * - * tutorial book, reference manual, or both: * - * http://www.FreeRTOS.org/Documentation * - * * - *************************************************************************** - - http://www.FreeRTOS.org/FAQHelp.html - Having a problem? Start by reading - the FAQ page "My application does not run, what could be wrong?". Have you - defined configASSERT()? - - http://www.FreeRTOS.org/support - In return for receiving this top quality - embedded software for free we request you assist our global community by - participating in the support forum. - - http://www.FreeRTOS.org/training - Investing in training allows your team to - be as productive as possible as early as possible. Now you can receive - FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers - Ltd, and the world's leading authority on the world's leading RTOS. - - http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products, - including FreeRTOS+Trace - an indispensable productivity tool, a DOS - compatible FAT file system, and our tiny thread aware UDP/IP stack. - - http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate. - Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS. - - http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High - Integrity Systems ltd. to sell under the OpenRTOS brand. Low cost OpenRTOS - licenses offer ticketed support, indemnification and commercial middleware. - - http://www.SafeRTOS.com - High Integrity Systems also provide a safety - engineered and independently SIL3 certified version for use in safety and - mission critical applications that require provable dependability. - - 1 tab == 4 spaces! -*/ + * FreeRTOS Kernel V10.0.1 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ /* * This is the list implementation used by the scheduler. While it is tailored @@ -205,7 +163,7 @@ typedef struct xMINI_LIST_ITEM MiniListItem_t; typedef struct xLIST { listFIRST_LIST_INTEGRITY_CHECK_VALUE /*< Set to a known value if configUSE_LIST_DATA_INTEGRITY_CHECK_BYTES is set to 1. */ - configLIST_VOLATILE UBaseType_t uxNumberOfItems; + volatile UBaseType_t uxNumberOfItems; ListItem_t* configLIST_VOLATILE pxIndex; /*< Used to walk through the list. Points to the last item returned by a call to listGET_OWNER_OF_NEXT_ENTRY (). */ MiniListItem_t xListEnd; /*< List item that contains the maximum possible item value meaning it is always at the end of the list and is therefore used as a marker. */ listSECOND_LIST_INTEGRITY_CHECK_VALUE /*< Set to a known value if configUSE_LIST_DATA_INTEGRITY_CHECK_BYTES is set to 1. */ @@ -414,12 +372,12 @@ void vListInsert( List_t* const pxList, ListItem_t* const pxNewListItem ) PRIVIL * such that it will be the last item within the list returned by multiple * calls to listGET_OWNER_OF_NEXT_ENTRY. * - * The list member pvIndex is used to walk through a list. Calling - * listGET_OWNER_OF_NEXT_ENTRY increments pvIndex to the next item in the list. + * The list member pxIndex is used to walk through a list. Calling + * listGET_OWNER_OF_NEXT_ENTRY increments pxIndex to the next item in the list. * Placing an item in a list using vListInsertEnd effectively places the item - * in the list position pointed to by pvIndex. This means that every other + * in the list position pointed to by pxIndex. This means that every other * item within the list will be returned by listGET_OWNER_OF_NEXT_ENTRY before - * the pvIndex parameter again points to the item being inserted. + * the pxIndex parameter again points to the item being inserted. * * @param pxList The list into which the item is to be inserted. * diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/message_buffer.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/message_buffer.h new file mode 100644 index 00000000..e1fd6c56 --- /dev/null +++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/message_buffer.h @@ -0,0 +1,779 @@ +/* + * FreeRTOS Kernel V10.0.1 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ + + +/* + * Message buffers build functionality on top of FreeRTOS stream buffers. + * Whereas stream buffers are used to send a continuous stream of data from one + * task or interrupt to another, message buffers are used to send variable + * length discrete messages from one task or interrupt to another. Their + * implementation is light weight, making them particularly suited for interrupt + * to task and core to core communication scenarios. + * + * ***NOTE***: Uniquely among FreeRTOS objects, the stream buffer + * implementation (so also the message buffer implementation, as message buffers + * are built on top of stream buffers) assumes there is only one task or + * interrupt that will write to the buffer (the writer), and only one task or + * interrupt that will read from the buffer (the reader). It is safe for the + * writer and reader to be different tasks or interrupts, but, unlike other + * FreeRTOS objects, it is not safe to have multiple different writers or + * multiple different readers. If there are to be multiple different writers + * then the application writer must place each call to a writing API function + * (such as xMessageBufferSend()) inside a critical section and set the send + * block time to 0. Likewise, if there are to be multiple different readers + * then the application writer must place each call to a reading API function + * (such as xMessageBufferRead()) inside a critical section and set the receive + * timeout to 0. + * + * Message buffers hold variable length messages. To enable that, when a + * message is written to the message buffer an additional sizeof( size_t ) bytes + * are also written to store the message's length (that happens internally, with + * the API function). sizeof( size_t ) is typically 4 bytes on a 32-bit + * architecture, so writing a 10 byte message to a message buffer on a 32-bit + * architecture will actually reduce the available space in the message buffer + * by 14 bytes (10 byte are used by the message, and 4 bytes to hold the length + * of the message). + */ + +#ifndef FREERTOS_MESSAGE_BUFFER_H +#define FREERTOS_MESSAGE_BUFFER_H + +/* Message buffers are built onto of stream buffers. */ +#include "stream_buffer.h" + +#if defined( __cplusplus ) +extern "C" { +#endif + +/** + * Type by which message buffers are referenced. For example, a call to + * xMessageBufferCreate() returns an MessageBufferHandle_t variable that can + * then be used as a parameter to xMessageBufferSend(), xMessageBufferReceive(), + * etc. + */ +typedef void* MessageBufferHandle_t; + +/*-----------------------------------------------------------*/ + +/** + * message_buffer.h + * +
+MessageBufferHandle_t xMessageBufferCreate( size_t xBufferSizeBytes );
+
+ * + * Creates a new message buffer using dynamically allocated memory. See + * xMessageBufferCreateStatic() for a version that uses statically allocated + * memory (memory that is allocated at compile time). + * + * configSUPPORT_DYNAMIC_ALLOCATION must be set to 1 or left undefined in + * FreeRTOSConfig.h for xMessageBufferCreate() to be available. + * + * @param xBufferSizeBytes The total number of bytes (not messages) the message + * buffer will be able to hold at any one time. When a message is written to + * the message buffer an additional sizeof( size_t ) bytes are also written to + * store the message's length. sizeof( size_t ) is typically 4 bytes on a + * 32-bit architecture, so on most 32-bit architectures a 10 byte message will + * take up 14 bytes of message buffer space. + * + * @return If NULL is returned, then the message buffer cannot be created + * because there is insufficient heap memory available for FreeRTOS to allocate + * the message buffer data structures and storage area. A non-NULL value being + * returned indicates that the message buffer has been created successfully - + * the returned value should be stored as the handle to the created message + * buffer. + * + * Example use: +
+
+void vAFunction( void )
+{
+MessageBufferHandle_t xMessageBuffer;
+const size_t xMessageBufferSizeBytes = 100;
+
+    // Create a message buffer that can hold 100 bytes.  The memory used to hold
+    // both the message buffer structure and the messages themselves is allocated
+    // dynamically.  Each message added to the buffer consumes an additional 4
+    // bytes which are used to hold the lengh of the message.
+    xMessageBuffer = xMessageBufferCreate( xMessageBufferSizeBytes );
+
+    if( xMessageBuffer == NULL )
+    {
+        // There was not enough heap memory space available to create the
+        // message buffer.
+    }
+    else
+    {
+        // The message buffer was created successfully and can now be used.
+    }
+
+
+ * \defgroup xMessageBufferCreate xMessageBufferCreate + * \ingroup MessageBufferManagement + */ +#define xMessageBufferCreate( xBufferSizeBytes ) ( MessageBufferHandle_t ) xStreamBufferGenericCreate( xBufferSizeBytes, ( size_t ) 0, pdTRUE ) + +/** + * message_buffer.h + * +
+MessageBufferHandle_t xMessageBufferCreateStatic( size_t xBufferSizeBytes,
+                                                  uint8_t *pucMessageBufferStorageArea,
+                                                  StaticMessageBuffer_t *pxStaticMessageBuffer );
+
+ * Creates a new message buffer using statically allocated memory. See + * xMessageBufferCreate() for a version that uses dynamically allocated memory. + * + * @param xBufferSizeBytes The size, in bytes, of the buffer pointed to by the + * pucMessageBufferStorageArea parameter. When a message is written to the + * message buffer an additional sizeof( size_t ) bytes are also written to store + * the message's length. sizeof( size_t ) is typically 4 bytes on a 32-bit + * architecture, so on most 32-bit architecture a 10 byte message will take up + * 14 bytes of message buffer space. The maximum number of bytes that can be + * stored in the message buffer is actually (xBufferSizeBytes - 1). + * + * @param pucMessageBufferStorageArea Must point to a uint8_t array that is at + * least xBufferSizeBytes + 1 big. This is the array to which messages are + * copied when they are written to the message buffer. + * + * @param pxStaticMessageBuffer Must point to a variable of type + * StaticMessageBuffer_t, which will be used to hold the message buffer's data + * structure. + * + * @return If the message buffer is created successfully then a handle to the + * created message buffer is returned. If either pucMessageBufferStorageArea or + * pxStaticmessageBuffer are NULL then NULL is returned. + * + * Example use: +
+
+// Used to dimension the array used to hold the messages.  The available space
+// will actually be one less than this, so 999.
+#define STORAGE_SIZE_BYTES 1000
+
+// Defines the memory that will actually hold the messages within the message
+// buffer.
+static uint8_t ucStorageBuffer[ STORAGE_SIZE_BYTES ];
+
+// The variable used to hold the message buffer structure.
+StaticMessageBuffer_t xMessageBufferStruct;
+
+void MyFunction( void )
+{
+MessageBufferHandle_t xMessageBuffer;
+
+    xMessageBuffer = xMessageBufferCreateStatic( sizeof( ucBufferStorage ),
+                                                 ucBufferStorage,
+                                                 &xMessageBufferStruct );
+
+    // As neither the pucMessageBufferStorageArea or pxStaticMessageBuffer
+    // parameters were NULL, xMessageBuffer will not be NULL, and can be used to
+    // reference the created message buffer in other message buffer API calls.
+
+    // Other code that uses the message buffer can go here.
+}
+
+
+ * \defgroup xMessageBufferCreateStatic xMessageBufferCreateStatic + * \ingroup MessageBufferManagement + */ +#define xMessageBufferCreateStatic( xBufferSizeBytes, pucMessageBufferStorageArea, pxStaticMessageBuffer ) ( MessageBufferHandle_t ) xStreamBufferGenericCreateStatic( xBufferSizeBytes, 0, pdTRUE, pucMessageBufferStorageArea, pxStaticMessageBuffer ) + +/** + * message_buffer.h + * +
+size_t xMessageBufferSend( MessageBufferHandle_t xMessageBuffer,
+                           const void *pvTxData,
+                           size_t xDataLengthBytes,
+                           TickType_t xTicksToWait );
+
+ *
+ * Sends a discrete message to the message buffer.  The message can be any
+ * length that fits within the buffer's free space, and is copied into the
+ * buffer.
+ *
+ * ***NOTE***:  Uniquely among FreeRTOS objects, the stream buffer
+ * implementation (so also the message buffer implementation, as message buffers
+ * are built on top of stream buffers) assumes there is only one task or
+ * interrupt that will write to the buffer (the writer), and only one task or
+ * interrupt that will read from the buffer (the reader).  It is safe for the
+ * writer and reader to be different tasks or interrupts, but, unlike other
+ * FreeRTOS objects, it is not safe to have multiple different writers or
+ * multiple different readers.  If there are to be multiple different writers
+ * then the application writer must place each call to a writing API function
+ * (such as xMessageBufferSend()) inside a critical section and set the send
+ * block time to 0.  Likewise, if there are to be multiple different readers
+ * then the application writer must place each call to a reading API function
+ * (such as xMessageBufferRead()) inside a critical section and set the receive
+ * block time to 0.
+ *
+ * Use xMessageBufferSend() to write to a message buffer from a task.  Use
+ * xMessageBufferSendFromISR() to write to a message buffer from an interrupt
+ * service routine (ISR).
+ *
+ * @param xMessageBuffer The handle of the message buffer to which a message is
+ * being sent.
+ *
+ * @param pvTxData A pointer to the message that is to be copied into the
+ * message buffer.
+ *
+ * @param xDataLengthBytes The length of the message.  That is, the number of
+ * bytes to copy from pvTxData into the message buffer.  When a message is
+ * written to the message buffer an additional sizeof( size_t ) bytes are also
+ * written to store the message's length.  sizeof( size_t ) is typically 4 bytes
+ * on a 32-bit architecture, so on most 32-bit architecture setting
+ * xDataLengthBytes to 20 will reduce the free space in the message buffer by 24
+ * bytes (20 bytes of message data and 4 bytes to hold the message length).
+ *
+ * @param xTicksToWait The maximum amount of time the calling task should remain
+ * in the Blocked state to wait for enough space to become available in the
+ * message buffer, should the message buffer have insufficient space when
+ * xMessageBufferSend() is called.  The calling task will never block if
+ * xTicksToWait is zero.  The block time is specified in tick periods, so the
+ * absolute time it represents is dependent on the tick frequency.  The macro
+ * pdMS_TO_TICKS() can be used to convert a time specified in milliseconds into
+ * a time specified in ticks.  Setting xTicksToWait to portMAX_DELAY will cause
+ * the task to wait indefinitely (without timing out), provided
+ * INCLUDE_vTaskSuspend is set to 1 in FreeRTOSConfig.h.  Tasks do not use any
+ * CPU time when they are in the Blocked state.
+ *
+ * @return The number of bytes written to the message buffer.  If the call to
+ * xMessageBufferSend() times out before there was enough space to write the
+ * message into the message buffer then zero is returned.  If the call did not
+ * time out then xDataLengthBytes is returned.
+ *
+ * Example use:
+
+void vAFunction( MessageBufferHandle_t xMessageBuffer )
+{
+size_t xBytesSent;
+uint8_t ucArrayToSend[] = { 0, 1, 2, 3 };
+char *pcStringToSend = "String to send";
+const TickType_t x100ms = pdMS_TO_TICKS( 100 );
+
+    // Send an array to the message buffer, blocking for a maximum of 100ms to
+    // wait for enough space to be available in the message buffer.
+    xBytesSent = xMessageBufferSend( xMessageBuffer, ( void * ) ucArrayToSend, sizeof( ucArrayToSend ), x100ms );
+
+    if( xBytesSent != sizeof( ucArrayToSend ) )
+    {
+        // The call to xMessageBufferSend() times out before there was enough
+        // space in the buffer for the data to be written.
+    }
+
+    // Send the string to the message buffer.  Return immediately if there is
+    // not enough space in the buffer.
+    xBytesSent = xMessageBufferSend( xMessageBuffer, ( void * ) pcStringToSend, strlen( pcStringToSend ), 0 );
+
+    if( xBytesSent != strlen( pcStringToSend ) )
+    {
+        // The string could not be added to the message buffer because there was
+        // not enough free space in the buffer.
+    }
+}
+

+ * \defgroup xMessageBufferSend xMessageBufferSend
+ * \ingroup MessageBufferManagement
+ */
+#define xMessageBufferSend( xMessageBuffer, pvTxData, xDataLengthBytes, xTicksToWait ) xStreamBufferSend( ( StreamBufferHandle_t ) xMessageBuffer, pvTxData, xDataLengthBytes, xTicksToWait )
+
+/**
+ * message_buffer.h
+ *
+
+size_t xMessageBufferSendFromISR( MessageBufferHandle_t xMessageBuffer,
+                                  const void *pvTxData,
+                                  size_t xDataLengthBytes,
+                                  BaseType_t *pxHigherPriorityTaskWoken );
+
+ *
+ * Interrupt safe version of the API function that sends a discrete message to
+ * the message buffer.  The message can be any length that fits within the
+ * buffer's free space, and is copied into the buffer.
+ *
+ * ***NOTE***:  Uniquely among FreeRTOS objects, the stream buffer
+ * implementation (so also the message buffer implementation, as message buffers
+ * are built on top of stream buffers) assumes there is only one task or
+ * interrupt that will write to the buffer (the writer), and only one task or
+ * interrupt that will read from the buffer (the reader).  It is safe for the
+ * writer and reader to be different tasks or interrupts, but, unlike other
+ * FreeRTOS objects, it is not safe to have multiple different writers or
+ * multiple different readers.  If there are to be multiple different writers
+ * then the application writer must place each call to a writing API function
+ * (such as xMessageBufferSend()) inside a critical section and set the send
+ * block time to 0.  Likewise, if there are to be multiple different readers
+ * then the application writer must place each call to a reading API function
+ * (such as xMessageBufferRead()) inside a critical section and set the receive
+ * block time to 0.
+ *
+ * Use xMessageBufferSend() to write to a message buffer from a task.  Use
+ * xMessageBufferSendFromISR() to write to a message buffer from an interrupt
+ * service routine (ISR).
+ *
+ * @param xMessageBuffer The handle of the message buffer to which a message is
+ * being sent.
+ *
+ * @param pvTxData A pointer to the message that is to be copied into the
+ * message buffer.
+ *
+ * @param xDataLengthBytes The length of the message.  That is, the number of
+ * bytes to copy from pvTxData into the message buffer.  When a message is
+ * written to the message buffer an additional sizeof( size_t ) bytes are also
+ * written to store the message's length.  sizeof( size_t ) is typically 4 bytes
+ * on a 32-bit architecture, so on most 32-bit architecture setting
+ * xDataLengthBytes to 20 will reduce the free space in the message buffer by 24
+ * bytes (20 bytes of message data and 4 bytes to hold the message length).
+ *
+ * @param pxHigherPriorityTaskWoken  It is possible that a message buffer will
+ * have a task blocked on it waiting for data.  Calling
+ * xMessageBufferSendFromISR() can make data available, and so cause a task that
+ * was waiting for data to leave the Blocked state.  If calling
+ * xMessageBufferSendFromISR() causes a task to leave the Blocked state, and the
+ * unblocked task has a priority higher than the currently executing task (the
+ * task that was interrupted), then, internally, xMessageBufferSendFromISR()
+ * will set *pxHigherPriorityTaskWoken to pdTRUE.  If
+ * xMessageBufferSendFromISR() sets this value to pdTRUE, then normally a
+ * context switch should be performed before the interrupt is exited.  This will
+ * ensure that the interrupt returns directly to the highest priority Ready
+ * state task.  *pxHigherPriorityTaskWoken should be set to pdFALSE before it
+ * is passed into the function.  See the code example below for an example.
+ *
+ * @return The number of bytes actually written to the message buffer.  If the
+ * message buffer didn't have enough free space for the message to be stored
+ * then 0 is returned, otherwise xDataLengthBytes is returned.
+ *
+ * Example use:
+
+// A message buffer that has already been created.
+MessageBufferHandle_t xMessageBuffer;
+
+void vAnInterruptServiceRoutine( void )
+{
+size_t xBytesSent;
+char *pcStringToSend = "String to send";
+BaseType_t xHigherPriorityTaskWoken = pdFALSE; // Initialised to pdFALSE.
+
+    // Attempt to send the string to the message buffer.
+    xBytesSent = xMessageBufferSendFromISR( xMessageBuffer,
+                                            ( void * ) pcStringToSend,
+                                            strlen( pcStringToSend ),
+                                            &xHigherPriorityTaskWoken );
+
+    if( xBytesSent != strlen( pcStringToSend ) )
+    {
+        // The string could not be added to the message buffer because there was
+        // not enough free space in the buffer.
+    }
+
+    // If xHigherPriorityTaskWoken was set to pdTRUE inside
+    // xMessageBufferSendFromISR() then a task that has a priority above the
+    // priority of the currently executing task was unblocked and a context
+    // switch should be performed to ensure the ISR returns to the unblocked
+    // task.  In most FreeRTOS ports this is done by simply passing
+    // xHigherPriorityTaskWoken into taskYIELD_FROM_ISR(), which will test the
+    // variables value, and perform the context switch if necessary.  Check the
+    // documentation for the port in use for port specific instructions.
+    taskYIELD_FROM_ISR( xHigherPriorityTaskWoken );
+}
+

+ * \defgroup xMessageBufferSendFromISR xMessageBufferSendFromISR
+ * \ingroup MessageBufferManagement
+ */
+#define xMessageBufferSendFromISR( xMessageBuffer, pvTxData, xDataLengthBytes, pxHigherPriorityTaskWoken ) xStreamBufferSendFromISR( ( StreamBufferHandle_t ) xMessageBuffer, pvTxData, xDataLengthBytes, pxHigherPriorityTaskWoken )
+
+/**
+ * message_buffer.h
+ *
+
+size_t xMessageBufferReceive( MessageBufferHandle_t xMessageBuffer,
+                              void *pvRxData,
+                              size_t xBufferLengthBytes,
+                              TickType_t xTicksToWait );
+

+ *
+ * Receives a discrete message from a message buffer.  Messages can be of
+ * variable length and are copied out of the buffer.
+ *
+ * ***NOTE***:  Uniquely among FreeRTOS objects, the stream buffer
+ * implementation (so also the message buffer implementation, as message buffers
+ * are built on top of stream buffers) assumes there is only one task or
+ * interrupt that will write to the buffer (the writer), and only one task or
+ * interrupt that will read from the buffer (the reader).  It is safe for the
+ * writer and reader to be different tasks or interrupts, but, unlike other
+ * FreeRTOS objects, it is not safe to have multiple different writers or
+ * multiple different readers.  If there are to be multiple different writers
+ * then the application writer must place each call to a writing API function
+ * (such as xMessageBufferSend()) inside a critical section and set the send
+ * block time to 0.  Likewise, if there are to be multiple different readers
+ * then the application writer must place each call to a reading API function
+ * (such as xMessageBufferRead()) inside a critical section and set the receive
+ * block time to 0.
+ *
+ * Use xMessageBufferReceive() to read from a message buffer from a task.  Use
+ * xMessageBufferReceiveFromISR() to read from a message buffer from an
+ * interrupt service routine (ISR).
+ *
+ * @param xMessageBuffer The handle of the message buffer from which a message
+ * is being received.
+ *
+ * @param pvRxData A pointer to the buffer into which the received message is
+ * to be copied.
+ *
+ * @param xBufferLengthBytes The length of the buffer pointed to by the pvRxData
+ * parameter.  This sets the maximum length of the message that can be received.
+ * If xBufferLengthBytes is too small to hold the next message then the message
+ * will be left in the message buffer and 0 will be returned.
+ *
+ * @param xTicksToWait The maximum amount of time the task should remain in the
+ * Blocked state to wait for a message, should the message buffer be empty.
+ * xMessageBufferReceive() will return immediately if xTicksToWait is zero and
+ * the message buffer is empty.  The block time is specified in tick periods, so
+ * the absolute time it represents is dependent on the tick frequency.  The
+ * macro pdMS_TO_TICKS() can be used to convert a time specified in milliseconds
+ * into a time specified in ticks.  Setting xTicksToWait to portMAX_DELAY will
+ * cause the task to wait indefinitely (without timing out), provided
+ * INCLUDE_vTaskSuspend is set to 1 in FreeRTOSConfig.h.  Tasks do not use any
+ * CPU time when they are in the Blocked state.
+ *
+ * @return The length, in bytes, of the message read from the message buffer, if
+ * any.  If xMessageBufferReceive() times out before a message became available
+ * then zero is returned.  If the length of the message is greater than
+ * xBufferLengthBytes then the message will be left in the message buffer and
+ * zero is returned.
+ *
+ * Example use:
+
+void vAFunction( MessageBuffer_t xMessageBuffer )
+{
+uint8_t ucRxData[ 20 ];
+size_t xReceivedBytes;
+const TickType_t xBlockTime = pdMS_TO_TICKS( 20 );
+
+    // Receive the next message from the message buffer.  Wait in the Blocked
+    // state (so not using any CPU processing time) for a maximum of 100ms for
+    // a message to become available.
+    xReceivedBytes = xMessageBufferReceive( xMessageBuffer,
+                                            ( void * ) ucRxData,
+                                            sizeof( ucRxData ),
+                                            xBlockTime );
+
+    if( xReceivedBytes > 0 )
+    {
+        // A ucRxData contains a message that is xReceivedBytes long.  Process
+        // the message here....
+    }
+}
+

+ * \defgroup xMessageBufferReceive xMessageBufferReceive
+ * \ingroup MessageBufferManagement
+ */
+#define xMessageBufferReceive( xMessageBuffer, pvRxData, xBufferLengthBytes, xTicksToWait ) xStreamBufferReceive( ( StreamBufferHandle_t ) xMessageBuffer, pvRxData, xBufferLengthBytes, xTicksToWait )
+
+
+/**
+ * message_buffer.h
+ *
+
+size_t xMessageBufferReceiveFromISR( MessageBufferHandle_t xMessageBuffer,
+                                     void *pvRxData,
+                                     size_t xBufferLengthBytes,
+                                     BaseType_t *pxHigherPriorityTaskWoken );
+

+ *
+ * An interrupt safe version of the API function that receives a discrete
+ * message from a message buffer.  Messages can be of variable length and are
+ * copied out of the buffer.
+ *
+ * ***NOTE***:  Uniquely among FreeRTOS objects, the stream buffer
+ * implementation (so also the message buffer implementation, as message buffers
+ * are built on top of stream buffers) assumes there is only one task or
+ * interrupt that will write to the buffer (the writer), and only one task or
+ * interrupt that will read from the buffer (the reader).  It is safe for the
+ * writer and reader to be different tasks or interrupts, but, unlike other
+ * FreeRTOS objects, it is not safe to have multiple different writers or
+ * multiple different readers.  If there are to be multiple different writers
+ * then the application writer must place each call to a writing API function
+ * (such as xMessageBufferSend()) inside a critical section and set the send
+ * block time to 0.  Likewise, if there are to be multiple different readers
+ * then the application writer must place each call to a reading API function
+ * (such as xMessageBufferRead()) inside a critical section and set the receive
+ * block time to 0.
+ *
+ * Use xMessageBufferReceive() to read from a message buffer from a task.  Use
+ * xMessageBufferReceiveFromISR() to read from a message buffer from an
+ * interrupt service routine (ISR).
+ *
+ * @param xMessageBuffer The handle of the message buffer from which a message
+ * is being received.
+ *
+ * @param pvRxData A pointer to the buffer into which the received message is
+ * to be copied.
+ *
+ * @param xBufferLengthBytes The length of the buffer pointed to by the pvRxData
+ * parameter.  This sets the maximum length of the message that can be received.
+ * If xBufferLengthBytes is too small to hold the next message then the message
+ * will be left in the message buffer and 0 will be returned.
+ *
+ * @param pxHigherPriorityTaskWoken  It is possible that a message buffer will
+ * have a task blocked on it waiting for space to become available.  Calling
+ * xMessageBufferReceiveFromISR() can make space available, and so cause a task
+ * that is waiting for space to leave the Blocked state.  If calling
+ * xMessageBufferReceiveFromISR() causes a task to leave the Blocked state, and
+ * the unblocked task has a priority higher than the currently executing task
+ * (the task that was interrupted), then, internally,
+ * xMessageBufferReceiveFromISR() will set *pxHigherPriorityTaskWoken to pdTRUE.
+ * If xMessageBufferReceiveFromISR() sets this value to pdTRUE, then normally a
+ * context switch should be performed before the interrupt is exited.  That will
+ * ensure the interrupt returns directly to the highest priority Ready state
+ * task.  *pxHigherPriorityTaskWoken should be set to pdFALSE before it is
+ * passed into the function.  See the code example below for an example.
+ *
+ * @return The length, in bytes, of the message read from the message buffer, if
+ * any.
+ *
+ * Example use:
+
+// A message buffer that has already been created.
+MessageBuffer_t xMessageBuffer;
+
+void vAnInterruptServiceRoutine( void )
+{
+uint8_t ucRxData[ 20 ];
+size_t xReceivedBytes;
+BaseType_t xHigherPriorityTaskWoken = pdFALSE;  // Initialised to pdFALSE.
+
+    // Receive the next message from the message buffer.
+    xReceivedBytes = xMessageBufferReceiveFromISR( xMessageBuffer,
+                                                  ( void * ) ucRxData,
+                                                  sizeof( ucRxData ),
+                                                  &xHigherPriorityTaskWoken );
+
+    if( xReceivedBytes > 0 )
+    {
+        // A ucRxData contains a message that is xReceivedBytes long.  Process
+        // the message here....
+    }
+
+    // If xHigherPriorityTaskWoken was set to pdTRUE inside
+    // xMessageBufferReceiveFromISR() then a task that has a priority above the
+    // priority of the currently executing task was unblocked and a context
+    // switch should be performed to ensure the ISR returns to the unblocked
+    // task.  In most FreeRTOS ports this is done by simply passing
+    // xHigherPriorityTaskWoken into taskYIELD_FROM_ISR(), which will test the
+    // variables value, and perform the context switch if necessary.  Check the
+    // documentation for the port in use for port specific instructions.
+    taskYIELD_FROM_ISR( xHigherPriorityTaskWoken );
+}
+

+ * \defgroup xMessageBufferReceiveFromISR xMessageBufferReceiveFromISR
+ * \ingroup MessageBufferManagement
+ */
+#define xMessageBufferReceiveFromISR( xMessageBuffer, pvRxData, xBufferLengthBytes, pxHigherPriorityTaskWoken ) xStreamBufferReceiveFromISR( ( StreamBufferHandle_t ) xMessageBuffer, pvRxData, xBufferLengthBytes, pxHigherPriorityTaskWoken )
+
+/**
+ * message_buffer.h
+ *
+
+void vMessageBufferDelete( MessageBufferHandle_t xMessageBuffer );
+

+ *
+ * Deletes a message buffer that was previously created using a call to
+ * xMessageBufferCreate() or xMessageBufferCreateStatic().  If the message
+ * buffer was created using dynamic memory (that is, by xMessageBufferCreate()),
+ * then the allocated memory is freed.
+ *
+ * A message buffer handle must not be used after the message buffer has been
+ * deleted.
+ *
+ * @param xMessageBuffer The handle of the message buffer to be deleted.
+ *
+ */
+#define vMessageBufferDelete( xMessageBuffer ) vStreamBufferDelete( ( StreamBufferHandle_t ) xMessageBuffer )
+
+/**
+ * message_buffer.h
+
+BaseType_t xMessageBufferIsFull( MessageBufferHandle_t xMessageBuffer ) );
+

+ *
+ * Tests to see if a message buffer is full.  A message buffer is full if it
+ * cannot accept any more messages, of any size, until space is made available
+ * by a message being removed from the message buffer.
+ *
+ * @param xMessageBuffer The handle of the message buffer being queried.
+ *
+ * @return If the message buffer referenced by xMessageBuffer is full then
+ * pdTRUE is returned.  Otherwise pdFALSE is returned.
+ */
+#define xMessageBufferIsFull( xMessageBuffer ) xStreamBufferIsFull( ( StreamBufferHandle_t ) xMessageBuffer )
+
+/**
+ * message_buffer.h
+
+BaseType_t xMessageBufferIsEmpty( MessageBufferHandle_t xMessageBuffer ) );
+

+ *
+ * Tests to see if a message buffer is empty (does not contain any messages).
+ *
+ * @param xMessageBuffer The handle of the message buffer being queried.
+ *
+ * @return If the message buffer referenced by xMessageBuffer is empty then
+ * pdTRUE is returned.  Otherwise pdFALSE is returned.
+ *
+ */
+#define xMessageBufferIsEmpty( xMessageBuffer ) xStreamBufferIsEmpty( ( StreamBufferHandle_t ) xMessageBuffer )
+
+/**
+ * message_buffer.h
+
+BaseType_t xMessageBufferReset( MessageBufferHandle_t xMessageBuffer );
+

+ *
+ * Resets a message buffer to its initial empty state, discarding any message it
+ * contained.
+ *
+ * A message buffer can only be reset if there are no tasks blocked on it.
+ *
+ * @param xMessageBuffer The handle of the message buffer being reset.
+ *
+ * @return If the message buffer was reset then pdPASS is returned.  If the
+ * message buffer could not be reset because either there was a task blocked on
+ * the message queue to wait for space to become available, or to wait for a
+ * a message to be available, then pdFAIL is returned.
+ *
+ * \defgroup xMessageBufferReset xMessageBufferReset
+ * \ingroup MessageBufferManagement
+ */
+#define xMessageBufferReset( xMessageBuffer ) xStreamBufferReset( ( StreamBufferHandle_t ) xMessageBuffer )
+
+
+/**
+ * message_buffer.h
+
+size_t xMessageBufferSpaceAvailable( MessageBufferHandle_t xMessageBuffer ) );
+

+ * Returns the number of bytes of free space in the message buffer.
+ *
+ * @param xMessageBuffer The handle of the message buffer being queried.
+ *
+ * @return The number of bytes that can be written to the message buffer before
+ * the message buffer would be full.  When a message is written to the message
+ * buffer an additional sizeof( size_t ) bytes are also written to store the
+ * message's length.  sizeof( size_t ) is typically 4 bytes on a 32-bit
+ * architecture, so if xMessageBufferSpacesAvailable() returns 10, then the size
+ * of the largest message that can be written to the message buffer is 6 bytes.
+ *
+ * \defgroup xMessageBufferSpaceAvailable xMessageBufferSpaceAvailable
+ * \ingroup MessageBufferManagement
+ */
+#define xMessageBufferSpaceAvailable( xMessageBuffer ) xStreamBufferSpacesAvailable( ( StreamBufferHandle_t ) xMessageBuffer )
+
+/**
+ * message_buffer.h
+ *
+
+BaseType_t xMessageBufferSendCompletedFromISR( MessageBufferHandle_t xStreamBuffer, BaseType_t *pxHigherPriorityTaskWoken );
+

+ *
+ * For advanced users only.
+ *
+ * The sbSEND_COMPLETED() macro is called from within the FreeRTOS APIs when
+ * data is sent to a message buffer or stream buffer.  If there was a task that
+ * was blocked on the message or stream buffer waiting for data to arrive then
+ * the sbSEND_COMPLETED() macro sends a notification to the task to remove it
+ * from the Blocked state.  xMessageBufferSendCompletedFromISR() does the same
+ * thing.  It is provided to enable application writers to implement their own
+ * version of sbSEND_COMPLETED(), and MUST NOT BE USED AT ANY OTHER TIME.
+ *
+ * See the example implemented in FreeRTOS/Demo/Minimal/MessageBufferAMP.c for
+ * additional information.
+ *
+ * @param xStreamBuffer The handle of the stream buffer to which data was
+ * written.
+ *
+ * @param pxHigherPriorityTaskWoken *pxHigherPriorityTaskWoken should be
+ * initialised to pdFALSE before it is passed into
+ * xMessageBufferSendCompletedFromISR().  If calling
+ * xMessageBufferSendCompletedFromISR() removes a task from the Blocked state,
+ * and the task has a priority above the priority of the currently running task,
+ * then *pxHigherPriorityTaskWoken will get set to pdTRUE indicating that a
+ * context switch should be performed before exiting the ISR.
+ *
+ * @return If a task was removed from the Blocked state then pdTRUE is returned.
+ * Otherwise pdFALSE is returned.
+ *
+ * \defgroup xMessageBufferSendCompletedFromISR xMessageBufferSendCompletedFromISR
+ * \ingroup StreamBufferManagement
+ */
+#define xMessageBufferSendCompletedFromISR( xMessageBuffer, pxHigherPriorityTaskWoken ) xStreamBufferSendCompletedFromISR( ( StreamBufferHandle_t ) xMessageBuffer, pxHigherPriorityTaskWoken )
+
+/**
+ * message_buffer.h
+ *
+
+BaseType_t xMessageBufferReceiveCompletedFromISR( MessageBufferHandle_t xStreamBuffer, BaseType_t *pxHigherPriorityTaskWoken );
+

+ *
+ * For advanced users only.
+ *
+ * The sbRECEIVE_COMPLETED() macro is called from within the FreeRTOS APIs when
+ * data is read out of a message buffer or stream buffer.  If there was a task
+ * that was blocked on the message or stream buffer waiting for data to arrive
+ * then the sbRECEIVE_COMPLETED() macro sends a notification to the task to
+ * remove it from the Blocked state.  xMessageBufferReceiveCompletedFromISR()
+ * does the same thing.  It is provided to enable application writers to
+ * implement their own version of sbRECEIVE_COMPLETED(), and MUST NOT BE USED AT
+ * ANY OTHER TIME.
+ *
+ * See the example implemented in FreeRTOS/Demo/Minimal/MessageBufferAMP.c for
+ * additional information.
+ *
+ * @param xStreamBuffer The handle of the stream buffer from which data was
+ * read.
+ *
+ * @param pxHigherPriorityTaskWoken *pxHigherPriorityTaskWoken should be
+ * initialised to pdFALSE before it is passed into
+ * xMessageBufferReceiveCompletedFromISR().  If calling
+ * xMessageBufferReceiveCompletedFromISR() removes a task from the Blocked state,
+ * and the task has a priority above the priority of the currently running task,
+ * then *pxHigherPriorityTaskWoken will get set to pdTRUE indicating that a
+ * context switch should be performed before exiting the ISR.
+ *
+ * @return If a task was removed from the Blocked state then pdTRUE is returned.
+ * Otherwise pdFALSE is returned.
+ *
+ * \defgroup xMessageBufferReceiveCompletedFromISR xMessageBufferReceiveCompletedFromISR
+ * \ingroup StreamBufferManagement
+ */
+#define xMessageBufferReceiveCompletedFromISR( xMessageBuffer, pxHigherPriorityTaskWoken ) xStreamBufferReceiveCompletedFromISR( ( StreamBufferHandle_t ) xMessageBuffer, pxHigherPriorityTaskWoken )
+
+#if defined( __cplusplus )
+} /* extern "C" */
+#endif
+
+#endif	/* !defined( FREERTOS_MESSAGE_BUFFER_H ) */
diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/mpu_prototypes.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/mpu_prototypes.h
new file mode 100644
index 00000000..b6946534
--- /dev/null
+++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/mpu_prototypes.h
@@ -0,0 +1,155 @@
+/*
+ * FreeRTOS Kernel V10.0.1
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
+
+/*
+ * When the MPU is used the standard (non MPU) API functions are mapped to
+ * equivalents that start "MPU_", the prototypes for which are defined in this
+ * header files.  This will cause the application code to call the MPU_ version
+ * which wraps the non-MPU version with privilege promoting then demoting code,
+ * so the kernel code always runs will full privileges.
+ */
+
+
+#ifndef MPU_PROTOTYPES_H
+#define MPU_PROTOTYPES_H
+
+/* MPU versions of tasks.h API functions. */
+BaseType_t MPU_xTaskCreate( TaskFunction_t pxTaskCode, const char* const pcName, const uint16_t usStackDepth, void* const pvParameters, UBaseType_t uxPriority, TaskHandle_t* const pxCreatedTask );
+TaskHandle_t MPU_xTaskCreateStatic( TaskFunction_t pxTaskCode, const char* const pcName, const uint32_t ulStackDepth, void* const pvParameters, UBaseType_t uxPriority, StackType_t* const puxStackBuffer, StaticTask_t* const pxTaskBuffer );
+BaseType_t MPU_xTaskCreateRestricted( const TaskParameters_t* const pxTaskDefinition, TaskHandle_t* pxCreatedTask );
+BaseType_t MPU_xTaskCreateRestrictedStatic( const TaskParameters_t* const pxTaskDefinition, TaskHandle_t* pxCreatedTask );
+void MPU_vTaskAllocateMPURegions( TaskHandle_t xTask, const MemoryRegion_t* const pxRegions );
+void MPU_vTaskDelete( TaskHandle_t xTaskToDelete );
+void MPU_vTaskDelay( const TickType_t xTicksToDelay );
+void MPU_vTaskDelayUntil( TickType_t* const pxPreviousWakeTime, const TickType_t xTimeIncrement );
+BaseType_t MPU_xTaskAbortDelay( TaskHandle_t xTask );
+UBaseType_t MPU_uxTaskPriorityGet( TaskHandle_t xTask );
+eTaskState MPU_eTaskGetState( TaskHandle_t xTask );
+void MPU_vTaskGetInfo( TaskHandle_t xTask, TaskStatus_t* pxTaskStatus, BaseType_t xGetFreeStackSpace, eTaskState eState );
+void MPU_vTaskPrioritySet( TaskHandle_t xTask, UBaseType_t uxNewPriority );
+void MPU_vTaskSuspend( TaskHandle_t xTaskToSuspend );
+void MPU_vTaskResume( TaskHandle_t xTaskToResume );
+void MPU_vTaskStartScheduler( void );
+void MPU_vTaskSuspendAll( void );
+BaseType_t MPU_xTaskResumeAll( void );
+TickType_t MPU_xTaskGetTickCount( void );
+UBaseType_t MPU_uxTaskGetNumberOfTasks( void );
+char* MPU_pcTaskGetName( TaskHandle_t xTaskToQuery );
+TaskHandle_t MPU_xTaskGetHandle( const char* pcNameToQuery );
+UBaseType_t MPU_uxTaskGetStackHighWaterMark( TaskHandle_t xTask );
+void MPU_vTaskSetApplicationTaskTag( TaskHandle_t xTask, TaskHookFunction_t pxHookFunction );
+TaskHookFunction_t MPU_xTaskGetApplicationTaskTag( TaskHandle_t xTask );
+void MPU_vTaskSetThreadLocalStoragePointer( TaskHandle_t xTaskToSet, BaseType_t xIndex, void* pvValue );
+void* MPU_pvTaskGetThreadLocalStoragePointer( TaskHandle_t xTaskToQuery, BaseType_t xIndex );
+BaseType_t MPU_xTaskCallApplicationTaskHook( TaskHandle_t xTask, void* pvParameter );
+TaskHandle_t MPU_xTaskGetIdleTaskHandle( void );
+UBaseType_t MPU_uxTaskGetSystemState( TaskStatus_t* const pxTaskStatusArray, const UBaseType_t uxArraySize, uint32_t* const pulTotalRunTime );
+void MPU_vTaskList( char* pcWriteBuffer );
+void MPU_vTaskGetRunTimeStats( char* pcWriteBuffer );
+BaseType_t MPU_xTaskGenericNotify( TaskHandle_t xTaskToNotify, uint32_t ulValue, eNotifyAction eAction, uint32_t* pulPreviousNotificationValue );
+BaseType_t MPU_xTaskNotifyWait( uint32_t ulBitsToClearOnEntry, uint32_t ulBitsToClearOnExit, uint32_t* pulNotificationValue, TickType_t xTicksToWait );
+uint32_t MPU_ulTaskNotifyTake( BaseType_t xClearCountOnExit, TickType_t xTicksToWait );
+BaseType_t MPU_xTaskNotifyStateClear( TaskHandle_t xTask );
+BaseType_t MPU_xTaskIncrementTick( void );
+TaskHandle_t MPU_xTaskGetCurrentTaskHandle( void );
+void MPU_vTaskSetTimeOutState( TimeOut_t* const pxTimeOut );
+BaseType_t MPU_xTaskCheckForTimeOut( TimeOut_t* const pxTimeOut, TickType_t* const pxTicksToWait );
+void MPU_vTaskMissedYield( void );
+BaseType_t MPU_xTaskGetSchedulerState( void );
+
+/* MPU versions of queue.h API functions. */
+BaseType_t MPU_xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQueue, TickType_t xTicksToWait, const BaseType_t xCopyPosition );
+BaseType_t MPU_xQueueReceive( QueueHandle_t xQueue, void* const pvBuffer, TickType_t xTicksToWait );
+BaseType_t MPU_xQueuePeek( QueueHandle_t xQueue, void* const pvBuffer, TickType_t xTicksToWait );
+BaseType_t MPU_xQueueSemaphoreTake( QueueHandle_t xQueue, TickType_t xTicksToWait );
+UBaseType_t MPU_uxQueueMessagesWaiting( const QueueHandle_t xQueue );
+UBaseType_t MPU_uxQueueSpacesAvailable( const QueueHandle_t xQueue );
+void MPU_vQueueDelete( QueueHandle_t xQueue );
+QueueHandle_t MPU_xQueueCreateMutex( const uint8_t ucQueueType );
+QueueHandle_t MPU_xQueueCreateMutexStatic( const uint8_t ucQueueType, StaticQueue_t* pxStaticQueue );
+QueueHandle_t MPU_xQueueCreateCountingSemaphore( const UBaseType_t uxMaxCount, const UBaseType_t uxInitialCount );
+QueueHandle_t MPU_xQueueCreateCountingSemaphoreStatic( const UBaseType_t uxMaxCount, const UBaseType_t uxInitialCount, StaticQueue_t* pxStaticQueue );
+void* MPU_xQueueGetMutexHolder( QueueHandle_t xSemaphore );
+BaseType_t MPU_xQueueTakeMutexRecursive( QueueHandle_t xMutex, TickType_t xTicksToWait );
+BaseType_t MPU_xQueueGiveMutexRecursive( QueueHandle_t pxMutex );
+void MPU_vQueueAddToRegistry( QueueHandle_t xQueue, const char* pcName );
+void MPU_vQueueUnregisterQueue( QueueHandle_t xQueue );
+const char* MPU_pcQueueGetName( QueueHandle_t xQueue );
+QueueHandle_t MPU_xQueueGenericCreate( const UBaseType_t uxQueueLength, const UBaseType_t uxItemSize, const uint8_t ucQueueType );
+QueueHandle_t MPU_xQueueGenericCreateStatic( const UBaseType_t uxQueueLength, const UBaseType_t uxItemSize, uint8_t* pucQueueStorage, StaticQueue_t* pxStaticQueue, const uint8_t ucQueueType );
+QueueSetHandle_t MPU_xQueueCreateSet( const UBaseType_t uxEventQueueLength );
+BaseType_t MPU_xQueueAddToSet( QueueSetMemberHandle_t xQueueOrSemaphore, QueueSetHandle_t xQueueSet );
+BaseType_t MPU_xQueueRemoveFromSet( QueueSetMemberHandle_t xQueueOrSemaphore, QueueSetHandle_t xQueueSet );
+QueueSetMemberHandle_t MPU_xQueueSelectFromSet( QueueSetHandle_t xQueueSet, const TickType_t xTicksToWait );
+BaseType_t MPU_xQueueGenericReset( QueueHandle_t xQueue, BaseType_t xNewQueue );
+void MPU_vQueueSetQueueNumber( QueueHandle_t xQueue, UBaseType_t uxQueueNumber );
+UBaseType_t MPU_uxQueueGetQueueNumber( QueueHandle_t xQueue );
+uint8_t MPU_ucQueueGetQueueType( QueueHandle_t xQueue );
+
+/* MPU versions of timers.h API functions. */
+TimerHandle_t MPU_xTimerCreate( const char* const pcTimerName, const TickType_t xTimerPeriodInTicks, const UBaseType_t uxAutoReload, void* const pvTimerID, TimerCallbackFunction_t pxCallbackFunction );
+TimerHandle_t MPU_xTimerCreateStatic( const char* const pcTimerName, const TickType_t xTimerPeriodInTicks, const UBaseType_t uxAutoReload, void* const pvTimerID, TimerCallbackFunction_t pxCallbackFunction, StaticTimer_t* pxTimerBuffer );
+void* MPU_pvTimerGetTimerID( const TimerHandle_t xTimer );
+void MPU_vTimerSetTimerID( TimerHandle_t xTimer, void* pvNewID );
+BaseType_t MPU_xTimerIsTimerActive( TimerHandle_t xTimer );
+TaskHandle_t MPU_xTimerGetTimerDaemonTaskHandle( void );
+BaseType_t MPU_xTimerPendFunctionCall( PendedFunction_t xFunctionToPend, void* pvParameter1, uint32_t ulParameter2, TickType_t xTicksToWait );
+const char* MPU_pcTimerGetName( TimerHandle_t xTimer );
+TickType_t MPU_xTimerGetPeriod( TimerHandle_t xTimer );
+TickType_t MPU_xTimerGetExpiryTime( TimerHandle_t xTimer );
+BaseType_t MPU_xTimerCreateTimerTask( void );
+BaseType_t MPU_xTimerGenericCommand( TimerHandle_t xTimer, const BaseType_t xCommandID, const TickType_t xOptionalValue, BaseType_t* const pxHigherPriorityTaskWoken, const TickType_t xTicksToWait );
+
+/* MPU versions of event_group.h API functions. */
+EventGroupHandle_t MPU_xEventGroupCreate( void );
+EventGroupHandle_t MPU_xEventGroupCreateStatic( StaticEventGroup_t* pxEventGroupBuffer );
+EventBits_t MPU_xEventGroupWaitBits( EventGroupHandle_t xEventGroup, const EventBits_t uxBitsToWaitFor, const BaseType_t xClearOnExit, const BaseType_t xWaitForAllBits, TickType_t xTicksToWait );
+EventBits_t MPU_xEventGroupClearBits( EventGroupHandle_t xEventGroup, const EventBits_t uxBitsToClear );
+EventBits_t MPU_xEventGroupSetBits( EventGroupHandle_t xEventGroup, const EventBits_t uxBitsToSet );
+EventBits_t MPU_xEventGroupSync( EventGroupHandle_t xEventGroup, const EventBits_t uxBitsToSet, const EventBits_t uxBitsToWaitFor, TickType_t xTicksToWait );
+void MPU_vEventGroupDelete( EventGroupHandle_t xEventGroup );
+UBaseType_t MPU_uxEventGroupGetNumber( void* xEventGroup );
+
+/* MPU versions of message/stream_buffer.h API functions. */
+size_t MPU_xStreamBufferSend( StreamBufferHandle_t xStreamBuffer, const void* pvTxData, size_t xDataLengthBytes, TickType_t xTicksToWait );
+size_t MPU_xStreamBufferSendFromISR( StreamBufferHandle_t xStreamBuffer, const void* pvTxData, size_t xDataLengthBytes, BaseType_t* const pxHigherPriorityTaskWoken );
+size_t MPU_xStreamBufferReceive( StreamBufferHandle_t xStreamBuffer, void* pvRxData, size_t xBufferLengthBytes, TickType_t xTicksToWait );
+size_t MPU_xStreamBufferReceiveFromISR( StreamBufferHandle_t xStreamBuffer, void* pvRxData, size_t xBufferLengthBytes, BaseType_t* const pxHigherPriorityTaskWoken );
+void MPU_vStreamBufferDelete( StreamBufferHandle_t xStreamBuffer );
+BaseType_t MPU_xStreamBufferIsFull( StreamBufferHandle_t xStreamBuffer );
+BaseType_t MPU_xStreamBufferIsEmpty( StreamBufferHandle_t xStreamBuffer );
+BaseType_t MPU_xStreamBufferReset( StreamBufferHandle_t xStreamBuffer );
+size_t MPU_xStreamBufferSpacesAvailable( StreamBufferHandle_t xStreamBuffer );
+size_t MPU_xStreamBufferBytesAvailable( StreamBufferHandle_t xStreamBuffer );
+BaseType_t MPU_xStreamBufferSetTriggerLevel( StreamBufferHandle_t xStreamBuffer, size_t xTriggerLevel );
+StreamBufferHandle_t MPU_xStreamBufferGenericCreate( size_t xBufferSizeBytes, size_t xTriggerLevelBytes, BaseType_t xIsMessageBuffer );
+StreamBufferHandle_t MPU_xStreamBufferGenericCreateStatic( size_t xBufferSizeBytes, size_t xTriggerLevelBytes, BaseType_t xIsMessageBuffer, uint8_t* const pucStreamBufferStorageArea, StaticStreamBuffer_t* const pxStaticStreamBuffer );
+
+
+
+#endif /* MPU_PROTOTYPES_H */
+
diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/mpu_wrappers.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/mpu_wrappers.h
index 8d0f6784..514dc70b 100644
--- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/mpu_wrappers.h
+++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/mpu_wrappers.h
@@ -1,71 +1,29 @@
 /*
-    FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd.
-    All rights reserved
-
-    VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION.
-
-    This file is part of the FreeRTOS distribution.
-
-    FreeRTOS is free software; you can redistribute it and/or modify it under
-    the terms of the GNU General Public License (version 2) as published by the
-    Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception.
-
-    ***************************************************************************
-    >>!   NOTE: The modification to the GPL is included to allow you to     !<<
-    >>!   distribute a combined work that includes FreeRTOS without being   !<<
-    >>!   obliged to provide the source code for proprietary components     !<<
-    >>!   outside of the FreeRTOS kernel.                                   !<<
-    ***************************************************************************
-
-    FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY
-    WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
-    FOR A PARTICULAR PURPOSE.  Full license text is available on the following
-    link: http://www.freertos.org/a00114.html
-
-    ***************************************************************************
-     *                                                                       *
-     *    FreeRTOS provides completely free yet professionally developed,    *
-     *    robust, strictly quality controlled, supported, and cross          *
-     *    platform software that is more than just the market leader, it     *
-     *    is the industry's de facto standard.                               *
-     *                                                                       *
-     *    Help yourself get started quickly while simultaneously helping     *
-     *    to support the FreeRTOS project by purchasing a FreeRTOS           *
-     *    tutorial book, reference manual, or both:                          *
-     *    http://www.FreeRTOS.org/Documentation                              *
-     *                                                                       *
-    ***************************************************************************
-
-    http://www.FreeRTOS.org/FAQHelp.html - Having a problem?  Start by reading
-    the FAQ page "My application does not run, what could be wrong?".  Have you
-    defined configASSERT()?
-
-    http://www.FreeRTOS.org/support - In return for receiving this top quality
-    embedded software for free we request you assist our global community by
-    participating in the support forum.
-
-    http://www.FreeRTOS.org/training - Investing in training allows your team to
-    be as productive as possible as early as possible.  Now you can receive
-    FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers
-    Ltd, and the world's leading authority on the world's leading RTOS.
-
-    http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products,
-    including FreeRTOS+Trace - an indispensable productivity tool, a DOS
-    compatible FAT file system, and our tiny thread aware UDP/IP stack.
-
-    http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate.
-    Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS.
-
-    http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High
-    Integrity Systems ltd. to sell under the OpenRTOS brand.  Low cost OpenRTOS
-    licenses offer ticketed support, indemnification and commercial middleware.
-
-    http://www.SafeRTOS.com - High Integrity Systems also provide a safety
-    engineered and independently SIL3 certified version for use in safety and
-    mission critical applications that require provable dependability.
-
-    1 tab == 4 spaces!
-*/
+ * FreeRTOS Kernel V10.0.1
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
 
 #ifndef MPU_WRAPPERS_H
 #define MPU_WRAPPERS_H
@@ -79,82 +37,128 @@ included from queue.c or task.c to prevent it from having an effect within
 those files. */
 #ifndef MPU_WRAPPERS_INCLUDED_FROM_API_FILE
 
-#define xTaskGenericCreate				MPU_xTaskGenericCreate
-#define vTaskAllocateMPURegions			MPU_vTaskAllocateMPURegions
-#define vTaskDelete						MPU_vTaskDelete
-#define vTaskDelayUntil					MPU_vTaskDelayUntil
-#define vTaskDelay						MPU_vTaskDelay
-#define uxTaskPriorityGet				MPU_uxTaskPriorityGet
-#define vTaskPrioritySet				MPU_vTaskPrioritySet
-#define eTaskGetState					MPU_eTaskGetState
-#define vTaskSuspend					MPU_vTaskSuspend
-#define vTaskResume						MPU_vTaskResume
-#define vTaskSuspendAll					MPU_vTaskSuspendAll
-#define xTaskResumeAll					MPU_xTaskResumeAll
-#define xTaskGetTickCount				MPU_xTaskGetTickCount
-#define uxTaskGetNumberOfTasks			MPU_uxTaskGetNumberOfTasks
-#define vTaskList						MPU_vTaskList
-#define vTaskGetRunTimeStats			MPU_vTaskGetRunTimeStats
-#define vTaskSetApplicationTaskTag		MPU_vTaskSetApplicationTaskTag
-#define xTaskGetApplicationTaskTag		MPU_xTaskGetApplicationTaskTag
-#define xTaskCallApplicationTaskHook	MPU_xTaskCallApplicationTaskHook
-#define uxTaskGetStackHighWaterMark		MPU_uxTaskGetStackHighWaterMark
-#define xTaskGetCurrentTaskHandle		MPU_xTaskGetCurrentTaskHandle
-#define xTaskGetSchedulerState			MPU_xTaskGetSchedulerState
-#define xTaskGetIdleTaskHandle			MPU_xTaskGetIdleTaskHandle
-#define uxTaskGetSystemState			MPU_uxTaskGetSystemState
-#define xTaskGenericNotify				MPU_xTaskGenericNotify
-#define xTaskNotifyWait					MPU_xTaskNotifyWait
-#define ulTaskNotifyTake				MPU_ulTaskNotifyTake
-
-#define xQueueGenericCreate				MPU_xQueueGenericCreate
-#define xQueueCreateMutex				MPU_xQueueCreateMutex
-#define xQueueGiveMutexRecursive		MPU_xQueueGiveMutexRecursive
-#define xQueueTakeMutexRecursive		MPU_xQueueTakeMutexRecursive
-#define xQueueCreateCountingSemaphore	MPU_xQueueCreateCountingSemaphore
-#define xQueueGenericSend				MPU_xQueueGenericSend
-#define xQueueAltGenericSend			MPU_xQueueAltGenericSend
-#define xQueueAltGenericReceive			MPU_xQueueAltGenericReceive
-#define xQueueGenericReceive			MPU_xQueueGenericReceive
-#define uxQueueMessagesWaiting			MPU_uxQueueMessagesWaiting
-#define vQueueDelete					MPU_vQueueDelete
-#define xQueueGenericReset				MPU_xQueueGenericReset
-#define xQueueCreateSet					MPU_xQueueCreateSet
-#define xQueueSelectFromSet				MPU_xQueueSelectFromSet
-#define xQueueAddToSet					MPU_xQueueAddToSet
-#define xQueueRemoveFromSet				MPU_xQueueRemoveFromSet
-#define xQueueGetMutexHolder			MPU_xQueueGetMutexHolder
-#define xQueueGetMutexHolder			MPU_xQueueGetMutexHolder
-
-#define pvPortMalloc					MPU_pvPortMalloc
-#define vPortFree						MPU_vPortFree
-#define xPortGetFreeHeapSize			MPU_xPortGetFreeHeapSize
-#define vPortInitialiseBlocks			MPU_vPortInitialiseBlocks
-#define xPortGetMinimumEverFreeHeapSize	MPU_xPortGetMinimumEverFreeHeapSize
-
-#if configQUEUE_REGISTRY_SIZE > 0
-#define vQueueAddToRegistry				MPU_vQueueAddToRegistry
-#define vQueueUnregisterQueue			MPU_vQueueUnregisterQueue
+/*
+ * Map standard (non MPU) API functions to equivalents that start
+ * "MPU_".  This will cause the application code to call the MPU_
+ * version, which wraps the non-MPU version with privilege promoting
+ * then demoting code, so the kernel code always runs will full
+ * privileges.
+ */
+
+/* Map standard tasks.h API functions to the MPU equivalents. */
+#define xTaskCreate								MPU_xTaskCreate
+#define xTaskCreateStatic						MPU_xTaskCreateStatic
+#define xTaskCreateRestricted					MPU_xTaskCreateRestricted
+#define vTaskAllocateMPURegions					MPU_vTaskAllocateMPURegions
+#define vTaskDelete								MPU_vTaskDelete
+#define vTaskDelay								MPU_vTaskDelay
+#define vTaskDelayUntil							MPU_vTaskDelayUntil
+#define xTaskAbortDelay							MPU_xTaskAbortDelay
+#define uxTaskPriorityGet						MPU_uxTaskPriorityGet
+#define eTaskGetState							MPU_eTaskGetState
+#define vTaskGetInfo							MPU_vTaskGetInfo
+#define vTaskPrioritySet						MPU_vTaskPrioritySet
+#define vTaskSuspend							MPU_vTaskSuspend
+#define vTaskResume								MPU_vTaskResume
+#define vTaskSuspendAll							MPU_vTaskSuspendAll
+#define xTaskResumeAll							MPU_xTaskResumeAll
+#define xTaskGetTickCount						MPU_xTaskGetTickCount
+#define uxTaskGetNumberOfTasks					MPU_uxTaskGetNumberOfTasks
+#define pcTaskGetName							MPU_pcTaskGetName
+#define xTaskGetHandle							MPU_xTaskGetHandle
+#define uxTaskGetStackHighWaterMark				MPU_uxTaskGetStackHighWaterMark
+#define vTaskSetApplicationTaskTag				MPU_vTaskSetApplicationTaskTag
+#define xTaskGetApplicationTaskTag				MPU_xTaskGetApplicationTaskTag
+#define vTaskSetThreadLocalStoragePointer		MPU_vTaskSetThreadLocalStoragePointer
+#define pvTaskGetThreadLocalStoragePointer		MPU_pvTaskGetThreadLocalStoragePointer
+#define xTaskCallApplicationTaskHook			MPU_xTaskCallApplicationTaskHook
+#define xTaskGetIdleTaskHandle					MPU_xTaskGetIdleTaskHandle
+#define uxTaskGetSystemState					MPU_uxTaskGetSystemState
+#define vTaskList								MPU_vTaskList
+#define vTaskGetRunTimeStats					MPU_vTaskGetRunTimeStats
+#define xTaskGenericNotify						MPU_xTaskGenericNotify
+#define xTaskNotifyWait							MPU_xTaskNotifyWait
+#define ulTaskNotifyTake						MPU_ulTaskNotifyTake
+#define xTaskNotifyStateClear					MPU_xTaskNotifyStateClear
+
+#define xTaskGetCurrentTaskHandle				MPU_xTaskGetCurrentTaskHandle
+#define vTaskSetTimeOutState					MPU_vTaskSetTimeOutState
+#define xTaskCheckForTimeOut					MPU_xTaskCheckForTimeOut
+#define xTaskGetSchedulerState					MPU_xTaskGetSchedulerState
+
+/* Map standard queue.h API functions to the MPU equivalents. */
+#define xQueueGenericSend						MPU_xQueueGenericSend
+#define xQueueReceive							MPU_xQueueReceive
+#define xQueuePeek								MPU_xQueuePeek
+#define xQueueSemaphoreTake						MPU_xQueueSemaphoreTake
+#define uxQueueMessagesWaiting					MPU_uxQueueMessagesWaiting
+#define uxQueueSpacesAvailable					MPU_uxQueueSpacesAvailable
+#define vQueueDelete							MPU_vQueueDelete
+#define xQueueCreateMutex						MPU_xQueueCreateMutex
+#define xQueueCreateMutexStatic					MPU_xQueueCreateMutexStatic
+#define xQueueCreateCountingSemaphore			MPU_xQueueCreateCountingSemaphore
+#define xQueueCreateCountingSemaphoreStatic		MPU_xQueueCreateCountingSemaphoreStatic
+#define xQueueGetMutexHolder					MPU_xQueueGetMutexHolder
+#define xQueueTakeMutexRecursive				MPU_xQueueTakeMutexRecursive
+#define xQueueGiveMutexRecursive				MPU_xQueueGiveMutexRecursive
+#define xQueueGenericCreate						MPU_xQueueGenericCreate
+#define xQueueGenericCreateStatic				MPU_xQueueGenericCreateStatic
+#define xQueueCreateSet							MPU_xQueueCreateSet
+#define xQueueAddToSet							MPU_xQueueAddToSet
+#define xQueueRemoveFromSet						MPU_xQueueRemoveFromSet
+#define xQueueSelectFromSet						MPU_xQueueSelectFromSet
+#define xQueueGenericReset						MPU_xQueueGenericReset
+
+#if( configQUEUE_REGISTRY_SIZE > 0 )
+#define vQueueAddToRegistry						MPU_vQueueAddToRegistry
+#define vQueueUnregisterQueue					MPU_vQueueUnregisterQueue
+#define pcQueueGetName							MPU_pcQueueGetName
 #endif
 
-#define xTimerCreate					MPU_xTimerCreate
-#define pvTimerGetTimerID				MPU_pvTimerGetTimerID
-#define vTimerSetTimerID				MPU_vTimerSetTimerID
-#define xTimerIsTimerActive				MPU_xTimerIsTimerActive
-#define xTimerGetTimerDaemonTaskHandle	MPU_xTimerGetTimerDaemonTaskHandle
-#define xTimerPendFunctionCall			MPU_xTimerPendFunctionCall
-#define pcTimerGetTimerName				MPU_pcTimerGetTimerName
-#define xTimerGenericCommand			MPU_xTimerGenericCommand
-
-#define xEventGroupCreate				MPU_xEventGroupCreate
-#define xEventGroupWaitBits				MPU_xEventGroupWaitBits
-#define xEventGroupClearBits			MPU_xEventGroupClearBits
-#define xEventGroupSetBits				MPU_xEventGroupSetBits
-#define xEventGroupSync					MPU_xEventGroupSync
-#define vEventGroupDelete				MPU_vEventGroupDelete
-
-/* Remove the privileged function macro. */
+/* Map standard timer.h API functions to the MPU equivalents. */
+#define xTimerCreate							MPU_xTimerCreate
+#define xTimerCreateStatic						MPU_xTimerCreateStatic
+#define pvTimerGetTimerID						MPU_pvTimerGetTimerID
+#define vTimerSetTimerID						MPU_vTimerSetTimerID
+#define xTimerIsTimerActive						MPU_xTimerIsTimerActive
+#define xTimerGetTimerDaemonTaskHandle			MPU_xTimerGetTimerDaemonTaskHandle
+#define xTimerPendFunctionCall					MPU_xTimerPendFunctionCall
+#define pcTimerGetName							MPU_pcTimerGetName
+#define xTimerGetPeriod							MPU_xTimerGetPeriod
+#define xTimerGetExpiryTime						MPU_xTimerGetExpiryTime
+#define xTimerGenericCommand					MPU_xTimerGenericCommand
+
+/* Map standard event_group.h API functions to the MPU equivalents. */
+#define xEventGroupCreate						MPU_xEventGroupCreate
+#define xEventGroupCreateStatic					MPU_xEventGroupCreateStatic
+#define xEventGroupWaitBits						MPU_xEventGroupWaitBits
+#define xEventGroupClearBits					MPU_xEventGroupClearBits
+#define xEventGroupSetBits						MPU_xEventGroupSetBits
+#define xEventGroupSync							MPU_xEventGroupSync
+#define vEventGroupDelete						MPU_vEventGroupDelete
+
+/* Map standard message/stream_buffer.h API functions to the MPU
+equivalents. */
+#define xStreamBufferSend						MPU_xStreamBufferSend
+#define xStreamBufferSendFromISR				MPU_xStreamBufferSendFromISR
+#define xStreamBufferReceive					MPU_xStreamBufferReceive
+#define xStreamBufferReceiveFromISR				MPU_xStreamBufferReceiveFromISR
+#define vStreamBufferDelete						MPU_vStreamBufferDelete
+#define xStreamBufferIsFull						MPU_xStreamBufferIsFull
+#define xStreamBufferIsEmpty					MPU_xStreamBufferIsEmpty
+#define xStreamBufferReset						MPU_xStreamBufferReset
+#define xStreamBufferSpacesAvailable			MPU_xStreamBufferSpacesAvailable
+#define xStreamBufferBytesAvailable				MPU_xStreamBufferBytesAvailable
+#define xStreamBufferSetTriggerLevel			MPU_xStreamBufferSetTriggerLevel
+#define xStreamBufferGenericCreate				MPU_xStreamBufferGenericCreate
+#define xStreamBufferGenericCreateStatic		MPU_xStreamBufferGenericCreateStatic
+
+
+/* Remove the privileged function macro, but keep the PRIVILEGED_DATA
+macro so applications can place data in privileged access sections
+(useful when using statically allocated objects). */
 #define PRIVILEGED_FUNCTION
+#define PRIVILEGED_DATA __attribute__((section("privileged_data")))
 
 #else /* MPU_WRAPPERS_INCLUDED_FROM_API_FILE */
 
diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/portable.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/portable.h
index fa7f3f4d..d678b919 100644
--- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/portable.h
+++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/portable.h
@@ -1,71 +1,29 @@
 /*
-    FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd.
-    All rights reserved
-
-    VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION.
-
-    This file is part of the FreeRTOS distribution.
-
-    FreeRTOS is free software; you can redistribute it and/or modify it under
-    the terms of the GNU General Public License (version 2) as published by the
-    Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception.
-
-    ***************************************************************************
-    >>!   NOTE: The modification to the GPL is included to allow you to     !<<
-    >>!   distribute a combined work that includes FreeRTOS without being   !<<
-    >>!   obliged to provide the source code for proprietary components     !<<
-    >>!   outside of the FreeRTOS kernel.                                   !<<
-    ***************************************************************************
-
-    FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY
-    WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
-    FOR A PARTICULAR PURPOSE.  Full license text is available on the following
-    link: http://www.freertos.org/a00114.html
-
-    ***************************************************************************
-     *                                                                       *
-     *    FreeRTOS provides completely free yet professionally developed,    *
-     *    robust, strictly quality controlled, supported, and cross          *
-     *    platform software that is more than just the market leader, it     *
-     *    is the industry's de facto standard.                               *
-     *                                                                       *
-     *    Help yourself get started quickly while simultaneously helping     *
-     *    to support the FreeRTOS project by purchasing a FreeRTOS           *
-     *    tutorial book, reference manual, or both:                          *
-     *    http://www.FreeRTOS.org/Documentation                              *
-     *                                                                       *
-    ***************************************************************************
-
-    http://www.FreeRTOS.org/FAQHelp.html - Having a problem?  Start by reading
-    the FAQ page "My application does not run, what could be wrong?".  Have you
-    defined configASSERT()?
-
-    http://www.FreeRTOS.org/support - In return for receiving this top quality
-    embedded software for free we request you assist our global community by
-    participating in the support forum.
-
-    http://www.FreeRTOS.org/training - Investing in training allows your team to
-    be as productive as possible as early as possible.  Now you can receive
-    FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers
-    Ltd, and the world's leading authority on the world's leading RTOS.
-
-    http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products,
-    including FreeRTOS+Trace - an indispensable productivity tool, a DOS
-    compatible FAT file system, and our tiny thread aware UDP/IP stack.
-
-    http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate.
-    Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS.
-
-    http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High
-    Integrity Systems ltd. to sell under the OpenRTOS brand.  Low cost OpenRTOS
-    licenses offer ticketed support, indemnification and commercial middleware.
-
-    http://www.SafeRTOS.com - High Integrity Systems also provide a safety
-    engineered and independently SIL3 certified version for use in safety and
-    mission critical applications that require provable dependability.
-
-    1 tab == 4 spaces!
-*/
+ * FreeRTOS Kernel V10.0.1
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
 
 /*-----------------------------------------------------------
  * Portable layer API.  Each function must be defined for each port.
@@ -196,7 +154,7 @@ void vPortEndScheduler( void ) PRIVILEGED_FUNCTION;
  */
 #if( portUSING_MPU_WRAPPERS == 1 )
 struct xMEMORY_REGION;
-void vPortStoreTaskMPUSettings( xMPU_SETTINGS* xMPUSettings, const struct xMEMORY_REGION* const xRegions, StackType_t* pxBottomOfStack, uint16_t usStackDepth ) PRIVILEGED_FUNCTION;
+void vPortStoreTaskMPUSettings( xMPU_SETTINGS* xMPUSettings, const struct xMEMORY_REGION* const xRegions, StackType_t* pxBottomOfStack, uint32_t ulStackDepth ) PRIVILEGED_FUNCTION;
 #endif
 
 #ifdef __cplusplus
diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/projdefs.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/projdefs.h
index e65ef3a6..8d66bb54 100644
--- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/projdefs.h
+++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/projdefs.h
@@ -1,71 +1,29 @@
 /*
-    FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd.
-    All rights reserved
-
-    VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION.
-
-    This file is part of the FreeRTOS distribution.
-
-    FreeRTOS is free software; you can redistribute it and/or modify it under
-    the terms of the GNU General Public License (version 2) as published by the
-    Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception.
-
-    ***************************************************************************
-    >>!   NOTE: The modification to the GPL is included to allow you to     !<<
-    >>!   distribute a combined work that includes FreeRTOS without being   !<<
-    >>!   obliged to provide the source code for proprietary components     !<<
-    >>!   outside of the FreeRTOS kernel.                                   !<<
-    ***************************************************************************
-
-    FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY
-    WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
-    FOR A PARTICULAR PURPOSE.  Full license text is available on the following
-    link: http://www.freertos.org/a00114.html
-
-    ***************************************************************************
-     *                                                                       *
-     *    FreeRTOS provides completely free yet professionally developed,    *
-     *    robust, strictly quality controlled, supported, and cross          *
-     *    platform software that is more than just the market leader, it     *
-     *    is the industry's de facto standard.                               *
-     *                                                                       *
-     *    Help yourself get started quickly while simultaneously helping     *
-     *    to support the FreeRTOS project by purchasing a FreeRTOS           *
-     *    tutorial book, reference manual, or both:                          *
-     *    http://www.FreeRTOS.org/Documentation                              *
-     *                                                                       *
-    ***************************************************************************
-
-    http://www.FreeRTOS.org/FAQHelp.html - Having a problem?  Start by reading
-    the FAQ page "My application does not run, what could be wrong?".  Have you
-    defined configASSERT()?
-
-    http://www.FreeRTOS.org/support - In return for receiving this top quality
-    embedded software for free we request you assist our global community by
-    participating in the support forum.
-
-    http://www.FreeRTOS.org/training - Investing in training allows your team to
-    be as productive as possible as early as possible.  Now you can receive
-    FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers
-    Ltd, and the world's leading authority on the world's leading RTOS.
-
-    http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products,
-    including FreeRTOS+Trace - an indispensable productivity tool, a DOS
-    compatible FAT file system, and our tiny thread aware UDP/IP stack.
-
-    http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate.
-    Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS.
-
-    http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High
-    Integrity Systems ltd. to sell under the OpenRTOS brand.  Low cost OpenRTOS
-    licenses offer ticketed support, indemnification and commercial middleware.
-
-    http://www.SafeRTOS.com - High Integrity Systems also provide a safety
-    engineered and independently SIL3 certified version for use in safety and
-    mission critical applications that require provable dependability.
-
-    1 tab == 4 spaces!
-*/
+ * FreeRTOS Kernel V10.0.1
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
 
 #ifndef PROJDEFS_H
 #define PROJDEFS_H
@@ -76,8 +34,12 @@
  */
 typedef void (*TaskFunction_t)( void* );
 
-/* Converts a time in milliseconds to a time in ticks. */
+/* Converts a time in milliseconds to a time in ticks.  This macro can be
+overridden by a macro of the same name defined in FreeRTOSConfig.h in case the
+definition here is not suitable for your application. */
+#ifndef pdMS_TO_TICKS
 #define pdMS_TO_TICKS( xTimeInMs ) ( ( TickType_t ) ( ( ( TickType_t ) ( xTimeInMs ) * ( TickType_t ) configTICK_RATE_HZ ) / ( TickType_t ) 1000 ) )
+#endif
 
 #define pdFALSE			( ( BaseType_t ) 0 )
 #define pdTRUE			( ( BaseType_t ) 1 )
@@ -107,6 +69,7 @@ typedef void (*TaskFunction_t)( void* );
 itself. */
 #define pdFREERTOS_ERRNO_NONE			0	/* No errors */
 #define	pdFREERTOS_ERRNO_ENOENT			2	/* No such file or directory */
+#define	pdFREERTOS_ERRNO_EINTR			4	/* Interrupted system call */
 #define	pdFREERTOS_ERRNO_EIO			5	/* I/O error */
 #define	pdFREERTOS_ERRNO_ENXIO			6	/* No such device or address */
 #define	pdFREERTOS_ERRNO_EBADF			9	/* Bad file number */
@@ -147,8 +110,13 @@ itself. */
 
 /* The following endian values are used by FreeRTOS+ components, not FreeRTOS
 itself. */
-#define pdFREERTOS_LITTLE_ENDIAN	0
-#define pdFREERTOS_BIG_ENDIAN		1
+#define pdFREERTOS_LITTLE_ENDIAN		0
+#define pdFREERTOS_BIG_ENDIAN			1
+
+/* Re-defining endian values for generic naming. */
+#define pdLITTLE_ENDIAN					pdFREERTOS_LITTLE_ENDIAN
+#define pdBIG_ENDIAN					pdFREERTOS_BIG_ENDIAN
+
 
 #endif /* PROJDEFS_H */
 
diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/queue.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/queue.h
index 5fe4dd11..72e6d001 100644
--- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/queue.h
+++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/queue.h
@@ -1,71 +1,29 @@
 /*
-    FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd.
-    All rights reserved
-
-    VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION.
-
-    This file is part of the FreeRTOS distribution.
-
-    FreeRTOS is free software; you can redistribute it and/or modify it under
-    the terms of the GNU General Public License (version 2) as published by the
-    Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception.
-
-    ***************************************************************************
-    >>!   NOTE: The modification to the GPL is included to allow you to     !<<
-    >>!   distribute a combined work that includes FreeRTOS without being   !<<
-    >>!   obliged to provide the source code for proprietary components     !<<
-    >>!   outside of the FreeRTOS kernel.                                   !<<
-    ***************************************************************************
-
-    FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY
-    WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
-    FOR A PARTICULAR PURPOSE.  Full license text is available on the following
-    link: http://www.freertos.org/a00114.html
-
-    ***************************************************************************
-     *                                                                       *
-     *    FreeRTOS provides completely free yet professionally developed,    *
-     *    robust, strictly quality controlled, supported, and cross          *
-     *    platform software that is more than just the market leader, it     *
-     *    is the industry's de facto standard.                               *
-     *                                                                       *
-     *    Help yourself get started quickly while simultaneously helping     *
-     *    to support the FreeRTOS project by purchasing a FreeRTOS           *
-     *    tutorial book, reference manual, or both:                          *
-     *    http://www.FreeRTOS.org/Documentation                              *
-     *                                                                       *
-    ***************************************************************************
-
-    http://www.FreeRTOS.org/FAQHelp.html - Having a problem?  Start by reading
-    the FAQ page "My application does not run, what could be wrong?".  Have you
-    defined configASSERT()?
-
-    http://www.FreeRTOS.org/support - In return for receiving this top quality
-    embedded software for free we request you assist our global community by
-    participating in the support forum.
-
-    http://www.FreeRTOS.org/training - Investing in training allows your team to
-    be as productive as possible as early as possible.  Now you can receive
-    FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers
-    Ltd, and the world's leading authority on the world's leading RTOS.
-
-    http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products,
-    including FreeRTOS+Trace - an indispensable productivity tool, a DOS
-    compatible FAT file system, and our tiny thread aware UDP/IP stack.
-
-    http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate.
-    Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS.
-
-    http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High
-    Integrity Systems ltd. to sell under the OpenRTOS brand.  Low cost OpenRTOS
-    licenses offer ticketed support, indemnification and commercial middleware.
-
-    http://www.SafeRTOS.com - High Integrity Systems also provide a safety
-    engineered and independently SIL3 certified version for use in safety and
-    mission critical applications that require provable dependability.
-
-    1 tab == 4 spaces!
-*/
+ * FreeRTOS Kernel V10.0.1
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
 
 
 #ifndef QUEUE_H
@@ -123,8 +81,20 @@ typedef void* QueueSetMemberHandle_t;
 						  );
  * 

  *
- * Creates a new queue instance.  This allocates the storage required by the
- * new queue and returns a handle for the queue.
+ * Creates a new queue instance, and returns a handle by which the new queue
+ * can be referenced.
+ *
+ * Internally, within the FreeRTOS implementation, queues use two blocks of
+ * memory.  The first block is used to hold the queue's data structures.  The
+ * second block is used to hold items placed into the queue.  If a queue is
+ * created using xQueueCreate() then both blocks of memory are automatically
+ * dynamically allocated inside the xQueueCreate() function.  (see
+ * http://www.freertos.org/a00111.html).  If a queue is created using
+ * xQueueCreateStatic() then the application writer must provide the memory that
+ * will get used by the queue.  xQueueCreateStatic() therefore allows a queue to
+ * be created without using any dynamic memory allocation.
+ *
+ * http://www.FreeRTOS.org/Embedded-RTOS-Queues.html
  *
  * @param uxQueueLength The maximum number of items that the queue can contain.
  *
@@ -170,7 +140,95 @@ typedef void* QueueSetMemberHandle_t;
  * \defgroup xQueueCreate xQueueCreate
  * \ingroup QueueManagement
  */
-#define xQueueCreate( uxQueueLength, uxItemSize ) xQueueGenericCreate( uxQueueLength, uxItemSize, queueQUEUE_TYPE_BASE )
+#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 )
+#define xQueueCreate( uxQueueLength, uxItemSize ) xQueueGenericCreate( ( uxQueueLength ), ( uxItemSize ), ( queueQUEUE_TYPE_BASE ) )
+#endif
+
+/**
+ * queue. h
+ * 
+ QueueHandle_t xQueueCreateStatic(
+							  UBaseType_t uxQueueLength,
+							  UBaseType_t uxItemSize,
+							  uint8_t *pucQueueStorageBuffer,
+							  StaticQueue_t *pxQueueBuffer
+						  );
+ * 

+ *
+ * Creates a new queue instance, and returns a handle by which the new queue
+ * can be referenced.
+ *
+ * Internally, within the FreeRTOS implementation, queues use two blocks of
+ * memory.  The first block is used to hold the queue's data structures.  The
+ * second block is used to hold items placed into the queue.  If a queue is
+ * created using xQueueCreate() then both blocks of memory are automatically
+ * dynamically allocated inside the xQueueCreate() function.  (see
+ * http://www.freertos.org/a00111.html).  If a queue is created using
+ * xQueueCreateStatic() then the application writer must provide the memory that
+ * will get used by the queue.  xQueueCreateStatic() therefore allows a queue to
+ * be created without using any dynamic memory allocation.
+ *
+ * http://www.FreeRTOS.org/Embedded-RTOS-Queues.html
+ *
+ * @param uxQueueLength The maximum number of items that the queue can contain.
+ *
+ * @param uxItemSize The number of bytes each item in the queue will require.
+ * Items are queued by copy, not by reference, so this is the number of bytes
+ * that will be copied for each posted item.  Each item on the queue must be
+ * the same size.
+ *
+ * @param pucQueueStorageBuffer If uxItemSize is not zero then
+ * pucQueueStorageBuffer must point to a uint8_t array that is at least large
+ * enough to hold the maximum number of items that can be in the queue at any
+ * one time - which is ( uxQueueLength * uxItemsSize ) bytes.  If uxItemSize is
+ * zero then pucQueueStorageBuffer can be NULL.
+ *
+ * @param pxQueueBuffer Must point to a variable of type StaticQueue_t, which
+ * will be used to hold the queue's data structure.
+ *
+ * @return If the queue is created then a handle to the created queue is
+ * returned.  If pxQueueBuffer is NULL then NULL is returned.
+ *
+ * Example usage:
+   
+ struct AMessage
+ {
+	char ucMessageID;
+	char ucData[ 20 ];
+ };
+
+ #define QUEUE_LENGTH 10
+ #define ITEM_SIZE sizeof( uint32_t )
+
+ // xQueueBuffer will hold the queue structure.
+ StaticQueue_t xQueueBuffer;
+
+ // ucQueueStorage will hold the items posted to the queue.  Must be at least
+ // [(queue length) * ( queue item size)] bytes long.
+ uint8_t ucQueueStorage[ QUEUE_LENGTH * ITEM_SIZE ];
+
+ void vATask( void *pvParameters )
+ {
+ QueueHandle_t xQueue1;
+
+	// Create a queue capable of containing 10 uint32_t values.
+	xQueue1 = xQueueCreate( QUEUE_LENGTH, // The number of items the queue can hold.
+							ITEM_SIZE	  // The size of each item in the queue
+							&( ucQueueStorage[ 0 ] ), // The buffer that will hold the items in the queue.
+							&xQueueBuffer ); // The buffer that will hold the queue structure.
+
+	// The queue is guaranteed to be created successfully as no dynamic memory
+	// allocation is used.  Therefore xQueue1 is now a handle to a valid queue.
+
+	// ... Rest of task code.
+ }
+ 

+ * \defgroup xQueueCreateStatic xQueueCreateStatic
+ * \ingroup QueueManagement
+ */
+#if( configSUPPORT_STATIC_ALLOCATION == 1 )
+#define xQueueCreateStatic( uxQueueLength, uxItemSize, pucQueueStorage, pxQueueBuffer ) xQueueGenericCreateStatic( ( uxQueueLength ), ( uxItemSize ), ( pucQueueStorage ), ( pxQueueBuffer ), ( queueQUEUE_TYPE_BASE ) )
+#endif /* configSUPPORT_STATIC_ALLOCATION */
 
 /**
  * queue. h
@@ -182,8 +240,6 @@ typedef void* QueueSetMemberHandle_t;
 							   );
  * 

  *
- * This is a macro that calls xQueueGenericSend().
- *
  * Post an item to the front of a queue.  The item is queued by copy, not by
  * reference.  This function must not be called from an interrupt service
  * routine.  See xQueueSendFromISR () for an alternative which may be used
@@ -596,12 +652,10 @@ BaseType_t xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQu
  * 
  BaseType_t xQueuePeek(
 							 QueueHandle_t xQueue,
-							 void *pvBuffer,
+							 void * const pvBuffer,
 							 TickType_t xTicksToWait
 						 );

  *
- * This is a macro that calls the xQueueGenericReceive() function.
- *
  * Receive an item from a queue without removing the item from the queue.
  * The item is received by copy so a buffer of adequate size must be
  * provided.  The number of bytes copied into the buffer was defined when
@@ -682,10 +736,10 @@ BaseType_t xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQu
 	// ... Rest of task code.
  }
  

- * \defgroup xQueueReceive xQueueReceive
+ * \defgroup xQueuePeek xQueuePeek
  * \ingroup QueueManagement
  */
-#define xQueuePeek( xQueue, pvBuffer, xTicksToWait ) xQueueGenericReceive( ( xQueue ), ( pvBuffer ), ( xTicksToWait ), pdTRUE )
+BaseType_t xQueuePeek( QueueHandle_t xQueue, void* const pvBuffer, TickType_t xTicksToWait ) PRIVILEGED_FUNCTION;
 
 /**
  * queue. h
@@ -729,8 +783,6 @@ BaseType_t xQueuePeekFromISR( QueueHandle_t xQueue, void* const pvBuffer ) PRIVI
 								 TickType_t xTicksToWait
 							);
* - * This is a macro that calls the xQueueGenericReceive() function. - * * Receive an item from a queue. The item is received by copy so a buffer of * adequate size must be provided. The number of bytes copied into the buffer * was defined when the queue was created. @@ -811,106 +863,7 @@ BaseType_t xQueuePeekFromISR( QueueHandle_t xQueue, void* const pvBuffer ) PRIVI * \defgroup xQueueReceive xQueueReceive * \ingroup QueueManagement */ -#define xQueueReceive( xQueue, pvBuffer, xTicksToWait ) xQueueGenericReceive( ( xQueue ), ( pvBuffer ), ( xTicksToWait ), pdFALSE ) - - -/** - * queue. h - * 
- BaseType_t xQueueGenericReceive(
-									   QueueHandle_t	xQueue,
-									   void	*pvBuffer,
-									   TickType_t	xTicksToWait
-									   BaseType_t	xJustPeek
-									);
- * - * It is preferred that the macro xQueueReceive() be used rather than calling - * this function directly. - * - * Receive an item from a queue. The item is received by copy so a buffer of - * adequate size must be provided. The number of bytes copied into the buffer - * was defined when the queue was created. - * - * This function must not be used in an interrupt service routine. See - * xQueueReceiveFromISR for an alternative that can. - * - * @param xQueue The handle to the queue from which the item is to be - * received. - * - * @param pvBuffer Pointer to the buffer into which the received item will - * be copied. - * - * @param xTicksToWait The maximum amount of time the task should block - * waiting for an item to receive should the queue be empty at the time - * of the call. The time is defined in tick periods so the constant - * portTICK_PERIOD_MS should be used to convert to real time if this is required. - * xQueueGenericReceive() will return immediately if the queue is empty and - * xTicksToWait is 0. - * - * @param xJustPeek When set to true, the item received from the queue is not - * actually removed from the queue - meaning a subsequent call to - * xQueueReceive() will return the same item. When set to false, the item - * being received from the queue is also removed from the queue. - * - * @return pdTRUE if an item was successfully received from the queue, - * otherwise pdFALSE. - * - * Example usage: - 
- struct AMessage
- {
-	char ucMessageID;
-	char ucData[ 20 ];
- } xMessage;
-
- QueueHandle_t xQueue;
-
- // Task to create a queue and post a value.
- void vATask( void *pvParameters )
- {
- struct AMessage *pxMessage;
-
-	// Create a queue capable of containing 10 pointers to AMessage structures.
-	// These should be passed by pointer as they contain a lot of data.
-	xQueue = xQueueCreate( 10, sizeof( struct AMessage * ) );
-	if( xQueue == 0 )
-	{
-		// Failed to create the queue.
-	}
-
-	// ...
-
-	// Send a pointer to a struct AMessage object.  Don't block if the
-	// queue is already full.
-	pxMessage = & xMessage;
-	xQueueSend( xQueue, ( void * ) &pxMessage, ( TickType_t ) 0 );
-
-	// ... Rest of task code.
- }
-
- // Task to receive from the queue.
- void vADifferentTask( void *pvParameters )
- {
- struct AMessage *pxRxedMessage;
-
-	if( xQueue != 0 )
-	{
-		// Receive a message on the created queue.  Block for 10 ticks if a
-		// message is not immediately available.
-		if( xQueueGenericReceive( xQueue, &( pxRxedMessage ), ( TickType_t ) 10 ) )
-		{
-			// pcRxedMessage now points to the struct AMessage variable posted
-			// by vATask.
-		}
-	}
-
-	// ... Rest of task code.
- }
-
- * \defgroup xQueueReceive xQueueReceive - * \ingroup QueueManagement - */ -BaseType_t xQueueGenericReceive( QueueHandle_t xQueue, void* const pvBuffer, TickType_t xTicksToWait, const BaseType_t xJustPeek ) PRIVILEGED_FUNCTION; +BaseType_t xQueueReceive( QueueHandle_t xQueue, void* const pvBuffer, TickType_t xTicksToWait ) PRIVILEGED_FUNCTION; /** * queue. h @@ -1437,28 +1390,6 @@ BaseType_t xQueueIsQueueEmptyFromISR( const QueueHandle_t xQueue ) PRIVILEGED_FU BaseType_t xQueueIsQueueFullFromISR( const QueueHandle_t xQueue ) PRIVILEGED_FUNCTION; UBaseType_t uxQueueMessagesWaitingFromISR( const QueueHandle_t xQueue ) PRIVILEGED_FUNCTION; - -/* - * xQueueAltGenericSend() is an alternative version of xQueueGenericSend(). - * Likewise xQueueAltGenericReceive() is an alternative version of - * xQueueGenericReceive(). - * - * The source code that implements the alternative (Alt) API is much - * simpler because it executes everything from within a critical section. - * This is the approach taken by many other RTOSes, but FreeRTOS.org has the - * preferred fully featured API too. The fully featured API has more - * complex code that takes longer to execute, but makes much less use of - * critical sections. Therefore the alternative API sacrifices interrupt - * responsiveness to gain execution speed, whereas the fully featured API - * sacrifices execution speed to ensure better interrupt responsiveness. - */ -BaseType_t xQueueAltGenericSend( QueueHandle_t xQueue, const void* const pvItemToQueue, TickType_t xTicksToWait, BaseType_t xCopyPosition ) PRIVILEGED_FUNCTION; -BaseType_t xQueueAltGenericReceive( QueueHandle_t xQueue, void* const pvBuffer, TickType_t xTicksToWait, BaseType_t xJustPeeking ) PRIVILEGED_FUNCTION; -#define xQueueAltSendToFront( xQueue, pvItemToQueue, xTicksToWait ) xQueueAltGenericSend( ( xQueue ), ( pvItemToQueue ), ( xTicksToWait ), queueSEND_TO_FRONT ) -#define xQueueAltSendToBack( xQueue, pvItemToQueue, xTicksToWait ) xQueueAltGenericSend( ( xQueue ), ( pvItemToQueue ), ( xTicksToWait ), queueSEND_TO_BACK ) -#define xQueueAltReceive( xQueue, pvBuffer, xTicksToWait ) xQueueAltGenericReceive( ( xQueue ), ( pvBuffer ), ( xTicksToWait ), pdFALSE ) -#define xQueueAltPeek( xQueue, pvBuffer, xTicksToWait ) xQueueAltGenericReceive( ( xQueue ), ( pvBuffer ), ( xTicksToWait ), pdTRUE ) - /* * The functions defined above are for passing data to and from tasks. The * functions below are the equivalents for passing data to and from @@ -1479,8 +1410,12 @@ BaseType_t xQueueCRReceive( QueueHandle_t xQueue, void* pvBuffer, TickType_t xTi * these functions directly. */ QueueHandle_t xQueueCreateMutex( const uint8_t ucQueueType ) PRIVILEGED_FUNCTION; +QueueHandle_t xQueueCreateMutexStatic( const uint8_t ucQueueType, StaticQueue_t* pxStaticQueue ) PRIVILEGED_FUNCTION; QueueHandle_t xQueueCreateCountingSemaphore( const UBaseType_t uxMaxCount, const UBaseType_t uxInitialCount ) PRIVILEGED_FUNCTION; +QueueHandle_t xQueueCreateCountingSemaphoreStatic( const UBaseType_t uxMaxCount, const UBaseType_t uxInitialCount, StaticQueue_t* pxStaticQueue ) PRIVILEGED_FUNCTION; +BaseType_t xQueueSemaphoreTake( QueueHandle_t xQueue, TickType_t xTicksToWait ) PRIVILEGED_FUNCTION; void* xQueueGetMutexHolder( QueueHandle_t xSemaphore ) PRIVILEGED_FUNCTION; +void* xQueueGetMutexHolderFromISR( QueueHandle_t xSemaphore ) PRIVILEGED_FUNCTION; /* * For internal use only. Use xSemaphoreTakeMutexRecursive() or @@ -1517,7 +1452,7 @@ BaseType_t xQueueGiveMutexRecursive( QueueHandle_t pxMutex ) PRIVILEGED_FUNCTION * stores a pointer to the string - so the string must be persistent (global or * preferably in ROM/Flash), not on the stack. */ -#if configQUEUE_REGISTRY_SIZE > 0 +#if( configQUEUE_REGISTRY_SIZE > 0 ) void vQueueAddToRegistry( QueueHandle_t xQueue, const char* pcName ) PRIVILEGED_FUNCTION; /*lint !e971 Unqualified char types are allowed for strings and single characters only. */ #endif @@ -1531,15 +1466,42 @@ void vQueueAddToRegistry( QueueHandle_t xQueue, const char* pcName ) PRIVILEGED_ * * @param xQueue The handle of the queue being removed from the registry. */ -#if configQUEUE_REGISTRY_SIZE > 0 +#if( configQUEUE_REGISTRY_SIZE > 0 ) void vQueueUnregisterQueue( QueueHandle_t xQueue ) PRIVILEGED_FUNCTION; #endif /* - * Generic version of the queue creation function, which is in turn called by - * any queue, semaphore or mutex creation function or macro. + * The queue registry is provided as a means for kernel aware debuggers to + * locate queues, semaphores and mutexes. Call pcQueueGetName() to look + * up and return the name of a queue in the queue registry from the queue's + * handle. + * + * @param xQueue The handle of the queue the name of which will be returned. + * @return If the queue is in the registry then a pointer to the name of the + * queue is returned. If the queue is not in the registry then NULL is + * returned. + */ +#if( configQUEUE_REGISTRY_SIZE > 0 ) +const char* pcQueueGetName( QueueHandle_t xQueue ) PRIVILEGED_FUNCTION; /*lint !e971 Unqualified char types are allowed for strings and single characters only. */ +#endif + +/* + * Generic version of the function used to creaet a queue using dynamic memory + * allocation. This is called by other functions and macros that create other + * RTOS objects that use the queue structure as their base. */ +#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) QueueHandle_t xQueueGenericCreate( const UBaseType_t uxQueueLength, const UBaseType_t uxItemSize, const uint8_t ucQueueType ) PRIVILEGED_FUNCTION; +#endif + +/* + * Generic version of the function used to creaet a queue using dynamic memory + * allocation. This is called by other functions and macros that create other + * RTOS objects that use the queue structure as their base. + */ +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) +QueueHandle_t xQueueGenericCreateStatic( const UBaseType_t uxQueueLength, const UBaseType_t uxItemSize, uint8_t* pucQueueStorage, StaticQueue_t* pxStaticQueue, const uint8_t ucQueueType ) PRIVILEGED_FUNCTION; +#endif /* * Queue sets provide a mechanism to allow a task to block (pend) on a read diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/semphr.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/semphr.h index b055ee09..96d07ca6 100644 --- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/semphr.h +++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/semphr.h @@ -1,71 +1,29 @@ /* - FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd. - All rights reserved - - VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION. - - This file is part of the FreeRTOS distribution. - - FreeRTOS is free software; you can redistribute it and/or modify it under - the terms of the GNU General Public License (version 2) as published by the - Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception. - - *************************************************************************** - >>! NOTE: The modification to the GPL is included to allow you to !<< - >>! distribute a combined work that includes FreeRTOS without being !<< - >>! obliged to provide the source code for proprietary components !<< - >>! outside of the FreeRTOS kernel. !<< - *************************************************************************** - - FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY - WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS - FOR A PARTICULAR PURPOSE. Full license text is available on the following - link: http://www.freertos.org/a00114.html - - *************************************************************************** - * * - * FreeRTOS provides completely free yet professionally developed, * - * robust, strictly quality controlled, supported, and cross * - * platform software that is more than just the market leader, it * - * is the industry's de facto standard. * - * * - * Help yourself get started quickly while simultaneously helping * - * to support the FreeRTOS project by purchasing a FreeRTOS * - * tutorial book, reference manual, or both: * - * http://www.FreeRTOS.org/Documentation * - * * - *************************************************************************** - - http://www.FreeRTOS.org/FAQHelp.html - Having a problem? Start by reading - the FAQ page "My application does not run, what could be wrong?". Have you - defined configASSERT()? - - http://www.FreeRTOS.org/support - In return for receiving this top quality - embedded software for free we request you assist our global community by - participating in the support forum. - - http://www.FreeRTOS.org/training - Investing in training allows your team to - be as productive as possible as early as possible. Now you can receive - FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers - Ltd, and the world's leading authority on the world's leading RTOS. - - http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products, - including FreeRTOS+Trace - an indispensable productivity tool, a DOS - compatible FAT file system, and our tiny thread aware UDP/IP stack. - - http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate. - Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS. - - http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High - Integrity Systems ltd. to sell under the OpenRTOS brand. Low cost OpenRTOS - licenses offer ticketed support, indemnification and commercial middleware. - - http://www.SafeRTOS.com - High Integrity Systems also provide a safety - engineered and independently SIL3 certified version for use in safety and - mission critical applications that require provable dependability. - - 1 tab == 4 spaces! -*/ + * FreeRTOS Kernel V10.0.1 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ #ifndef SEMAPHORE_H #define SEMAPHORE_H @@ -87,6 +45,10 @@ typedef QueueHandle_t SemaphoreHandle_t; * semphr. h * 
vSemaphoreCreateBinary( SemaphoreHandle_t xSemaphore )
* + * In many usage scenarios it is faster and more memory efficient to use a + * direct to task notification in place of a binary semaphore! + * http://www.freertos.org/RTOS-task-notifications.html + * * This old vSemaphoreCreateBinary() macro is now deprecated in favour of the * xSemaphoreCreateBinary() function. Note that binary semaphores created using * the vSemaphoreCreateBinary() macro are created in a state such that the @@ -128,19 +90,37 @@ typedef QueueHandle_t SemaphoreHandle_t; * \defgroup vSemaphoreCreateBinary vSemaphoreCreateBinary * \ingroup Semaphores */ +#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) #define vSemaphoreCreateBinary( xSemaphore ) \ - { \ - ( xSemaphore ) = xQueueGenericCreate( ( UBaseType_t ) 1, semSEMAPHORE_QUEUE_ITEM_LENGTH, queueQUEUE_TYPE_BINARY_SEMAPHORE ); \ - if( ( xSemaphore ) != NULL ) \ - { \ - ( void ) xSemaphoreGive( ( xSemaphore ) ); \ - } \ - } + { \ + ( xSemaphore ) = xQueueGenericCreate( ( UBaseType_t ) 1, semSEMAPHORE_QUEUE_ITEM_LENGTH, queueQUEUE_TYPE_BINARY_SEMAPHORE ); \ + if( ( xSemaphore ) != NULL ) \ + { \ + ( void ) xSemaphoreGive( ( xSemaphore ) ); \ + } \ + } +#endif /** * semphr. h * 
SemaphoreHandle_t xSemaphoreCreateBinary( void )
* + * Creates a new binary semaphore instance, and returns a handle by which the + * new semaphore can be referenced. + * + * In many usage scenarios it is faster and more memory efficient to use a + * direct to task notification in place of a binary semaphore! + * http://www.freertos.org/RTOS-task-notifications.html + * + * Internally, within the FreeRTOS implementation, binary semaphores use a block + * of memory, in which the semaphore structure is stored. If a binary semaphore + * is created using xSemaphoreCreateBinary() then the required memory is + * automatically dynamically allocated inside the xSemaphoreCreateBinary() + * function. (see http://www.freertos.org/a00111.html). If a binary semaphore + * is created using xSemaphoreCreateBinaryStatic() then the application writer + * must provide the memory. xSemaphoreCreateBinaryStatic() therefore allows a + * binary semaphore to be created without using any dynamic memory allocation. + * * The old vSemaphoreCreateBinary() macro is now deprecated in favour of this * xSemaphoreCreateBinary() function. Note that binary semaphores created using * the vSemaphoreCreateBinary() macro are created in a state such that the @@ -148,11 +128,6 @@ typedef QueueHandle_t SemaphoreHandle_t; * created using xSemaphoreCreateBinary() are created in a state such that the * the semaphore must first be 'given' before it can be 'taken'. * - * Function that creates a semaphore by using the existing queue mechanism. - * The queue length is 1 as this is a binary semaphore. The data size is 0 - * as nothing is actually stored - all that is important is whether the queue is - * empty or full (the binary semaphore is available or not). - * * This type of semaphore can be used for pure synchronisation between tasks or * between an interrupt and a task. The semaphore need not be given back once * obtained, so one task/interrupt can continuously 'give' the semaphore while @@ -160,7 +135,8 @@ typedef QueueHandle_t SemaphoreHandle_t; * semaphore does not use a priority inheritance mechanism. For an alternative * that does use priority inheritance see xSemaphoreCreateMutex(). * - * @return Handle to the created semaphore. + * @return Handle to the created semaphore, or NULL if the memory required to + * hold the semaphore's data structures could not be allocated. * * Example usage: 
@@ -168,7 +144,7 @@ typedef QueueHandle_t SemaphoreHandle_t;
 
  void vATask( void * pvParameters )
  {
-    // Semaphore cannot be used before a call to vSemaphoreCreateBinary ().
+    // Semaphore cannot be used before a call to xSemaphoreCreateBinary().
     // This is a macro so pass the variable in directly.
     xSemaphore = xSemaphoreCreateBinary();
 
@@ -179,10 +155,71 @@ typedef QueueHandle_t SemaphoreHandle_t;
     }
  }
- * \defgroup vSemaphoreCreateBinary vSemaphoreCreateBinary + * \defgroup xSemaphoreCreateBinary xSemaphoreCreateBinary * \ingroup Semaphores */ +#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) #define xSemaphoreCreateBinary() xQueueGenericCreate( ( UBaseType_t ) 1, semSEMAPHORE_QUEUE_ITEM_LENGTH, queueQUEUE_TYPE_BINARY_SEMAPHORE ) +#endif + +/** + * semphr. h + * 
SemaphoreHandle_t xSemaphoreCreateBinaryStatic( StaticSemaphore_t *pxSemaphoreBuffer )
+ * + * Creates a new binary semaphore instance, and returns a handle by which the + * new semaphore can be referenced. + * + * NOTE: In many usage scenarios it is faster and more memory efficient to use a + * direct to task notification in place of a binary semaphore! + * http://www.freertos.org/RTOS-task-notifications.html + * + * Internally, within the FreeRTOS implementation, binary semaphores use a block + * of memory, in which the semaphore structure is stored. If a binary semaphore + * is created using xSemaphoreCreateBinary() then the required memory is + * automatically dynamically allocated inside the xSemaphoreCreateBinary() + * function. (see http://www.freertos.org/a00111.html). If a binary semaphore + * is created using xSemaphoreCreateBinaryStatic() then the application writer + * must provide the memory. xSemaphoreCreateBinaryStatic() therefore allows a + * binary semaphore to be created without using any dynamic memory allocation. + * + * This type of semaphore can be used for pure synchronisation between tasks or + * between an interrupt and a task. The semaphore need not be given back once + * obtained, so one task/interrupt can continuously 'give' the semaphore while + * another continuously 'takes' the semaphore. For this reason this type of + * semaphore does not use a priority inheritance mechanism. For an alternative + * that does use priority inheritance see xSemaphoreCreateMutex(). + * + * @param pxSemaphoreBuffer Must point to a variable of type StaticSemaphore_t, + * which will then be used to hold the semaphore's data structure, removing the + * need for the memory to be allocated dynamically. + * + * @return If the semaphore is created then a handle to the created semaphore is + * returned. If pxSemaphoreBuffer is NULL then NULL is returned. + * + * Example usage: + 
+ SemaphoreHandle_t xSemaphore = NULL;
+ StaticSemaphore_t xSemaphoreBuffer;
+
+ void vATask( void * pvParameters )
+ {
+    // Semaphore cannot be used before a call to xSemaphoreCreateBinary().
+    // The semaphore's data structures will be placed in the xSemaphoreBuffer
+    // variable, the address of which is passed into the function.  The
+    // function's parameter is not NULL, so the function will not attempt any
+    // dynamic memory allocation, and therefore the function will not return
+    // return NULL.
+    xSemaphore = xSemaphoreCreateBinary( &xSemaphoreBuffer );
+
+    // Rest of task code goes here.
+ }
+
+ * \defgroup xSemaphoreCreateBinaryStatic xSemaphoreCreateBinaryStatic + * \ingroup Semaphores + */ +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) +#define xSemaphoreCreateBinaryStatic( pxStaticSemaphore ) xQueueGenericCreateStatic( ( UBaseType_t ) 1, semSEMAPHORE_QUEUE_ITEM_LENGTH, NULL, pxStaticSemaphore, queueQUEUE_TYPE_BINARY_SEMAPHORE ) +#endif /* configSUPPORT_STATIC_ALLOCATION */ /** * semphr. h @@ -192,7 +229,7 @@ typedef QueueHandle_t SemaphoreHandle_t; * ) * * Macro to obtain a semaphore. The semaphore must have previously been - * created with a call to vSemaphoreCreateBinary(), xSemaphoreCreateMutex() or + * created with a call to xSemaphoreCreateBinary(), xSemaphoreCreateMutex() or * xSemaphoreCreateCounting(). * * @param xSemaphore A handle to the semaphore being taken - obtained when @@ -215,7 +252,7 @@ typedef QueueHandle_t SemaphoreHandle_t; void vATask( void * pvParameters ) { // Create the semaphore to guard a shared resource. - vSemaphoreCreateBinary( xSemaphore ); + xSemaphore = xSemaphoreCreateBinary(); } // A task that uses the semaphore. @@ -249,7 +286,7 @@ typedef QueueHandle_t SemaphoreHandle_t; * \defgroup xSemaphoreTake xSemaphoreTake * \ingroup Semaphores */ -#define xSemaphoreTake( xSemaphore, xBlockTime ) xQueueGenericReceive( ( QueueHandle_t ) ( xSemaphore ), NULL, ( xBlockTime ), pdFALSE ) +#define xSemaphoreTake( xSemaphore, xBlockTime ) xQueueSemaphoreTake( ( xSemaphore ), ( xBlockTime ) ) /** * semphr. h @@ -313,23 +350,23 @@ typedef QueueHandle_t SemaphoreHandle_t; // ... // For some reason due to the nature of the code further calls to - // xSemaphoreTakeRecursive() are made on the same mutex. In real - // code these would not be just sequential calls as this would make - // no sense. Instead the calls are likely to be buried inside - // a more complex call structure. + // xSemaphoreTakeRecursive() are made on the same mutex. In real + // code these would not be just sequential calls as this would make + // no sense. Instead the calls are likely to be buried inside + // a more complex call structure. xSemaphoreTakeRecursive( xMutex, ( TickType_t ) 10 ); xSemaphoreTakeRecursive( xMutex, ( TickType_t ) 10 ); // The mutex has now been 'taken' three times, so will not be - // available to another task until it has also been given back - // three times. Again it is unlikely that real code would have - // these calls sequentially, but instead buried in a more complex - // call structure. This is just for illustrative purposes. + // available to another task until it has also been given back + // three times. Again it is unlikely that real code would have + // these calls sequentially, but instead buried in a more complex + // call structure. This is just for illustrative purposes. + xSemaphoreGiveRecursive( xMutex ); + xSemaphoreGiveRecursive( xMutex ); xSemaphoreGiveRecursive( xMutex ); - xSemaphoreGiveRecursive( xMutex ); - xSemaphoreGiveRecursive( xMutex ); - // Now the mutex can be taken by other tasks. + // Now the mutex can be taken by other tasks. } else { @@ -342,29 +379,16 @@ typedef QueueHandle_t SemaphoreHandle_t; * \defgroup xSemaphoreTakeRecursive xSemaphoreTakeRecursive * \ingroup Semaphores */ +#if( configUSE_RECURSIVE_MUTEXES == 1 ) #define xSemaphoreTakeRecursive( xMutex, xBlockTime ) xQueueTakeMutexRecursive( ( xMutex ), ( xBlockTime ) ) - - -/* - * xSemaphoreAltTake() is an alternative version of xSemaphoreTake(). - * - * The source code that implements the alternative (Alt) API is much - * simpler because it executes everything from within a critical section. - * This is the approach taken by many other RTOSes, but FreeRTOS.org has the - * preferred fully featured API too. The fully featured API has more - * complex code that takes longer to execute, but makes much less use of - * critical sections. Therefore the alternative API sacrifices interrupt - * responsiveness to gain execution speed, whereas the fully featured API - * sacrifices execution speed to ensure better interrupt responsiveness. - */ -#define xSemaphoreAltTake( xSemaphore, xBlockTime ) xQueueAltGenericReceive( ( QueueHandle_t ) ( xSemaphore ), NULL, ( xBlockTime ), pdFALSE ) +#endif /** * semphr. h * 
xSemaphoreGive( SemaphoreHandle_t xSemaphore )
* * Macro to release a semaphore. The semaphore must have previously been - * created with a call to vSemaphoreCreateBinary(), xSemaphoreCreateMutex() or + * created with a call to xSemaphoreCreateBinary(), xSemaphoreCreateMutex() or * xSemaphoreCreateCounting(). and obtained using sSemaphoreTake(). * * This macro must not be used from an ISR. See xSemaphoreGiveFromISR () for @@ -388,7 +412,7 @@ typedef QueueHandle_t SemaphoreHandle_t; void vATask( void * pvParameters ) { // Create the semaphore to guard a shared resource. - vSemaphoreCreateBinary( xSemaphore ); + xSemaphore = vSemaphoreCreateBinary(); if( xSemaphore != NULL ) { @@ -504,21 +528,9 @@ typedef QueueHandle_t SemaphoreHandle_t; * \defgroup xSemaphoreGiveRecursive xSemaphoreGiveRecursive * \ingroup Semaphores */ +#if( configUSE_RECURSIVE_MUTEXES == 1 ) #define xSemaphoreGiveRecursive( xMutex ) xQueueGiveMutexRecursive( ( xMutex ) ) - -/* - * xSemaphoreAltGive() is an alternative version of xSemaphoreGive(). - * - * The source code that implements the alternative (Alt) API is much - * simpler because it executes everything from within a critical section. - * This is the approach taken by many other RTOSes, but FreeRTOS.org has the - * preferred fully featured API too. The fully featured API has more - * complex code that takes longer to execute, but makes much less use of - * critical sections. Therefore the alternative API sacrifices interrupt - * responsiveness to gain execution speed, whereas the fully featured API - * sacrifices execution speed to ensure better interrupt responsiveness. - */ -#define xSemaphoreAltGive( xSemaphore ) xQueueAltGenericSend( ( QueueHandle_t ) ( xSemaphore ), NULL, semGIVE_BLOCK_TIME, queueSEND_TO_BACK ) +#endif /** * semphr. h @@ -529,7 +541,7 @@ typedef QueueHandle_t SemaphoreHandle_t; ) * * Macro to release a semaphore. The semaphore must have previously been - * created with a call to vSemaphoreCreateBinary() or xSemaphoreCreateCounting(). + * created with a call to xSemaphoreCreateBinary() or xSemaphoreCreateCounting(). * * Mutex type semaphores (those created using a call to xSemaphoreCreateMutex()) * must not be used with this macro. @@ -620,7 +632,7 @@ typedef QueueHandle_t SemaphoreHandle_t; ) * * Macro to take a semaphore from an ISR. The semaphore must have - * previously been created with a call to vSemaphoreCreateBinary() or + * previously been created with a call to xSemaphoreCreateBinary() or * xSemaphoreCreateCounting(). * * Mutex type semaphores (those created using a call to xSemaphoreCreateMutex()) @@ -649,12 +661,21 @@ typedef QueueHandle_t SemaphoreHandle_t; * semphr. h * 
SemaphoreHandle_t xSemaphoreCreateMutex( void )
* - * Macro that implements a mutex semaphore by using the existing queue - * mechanism. + * Creates a new mutex type semaphore instance, and returns a handle by which + * the new mutex can be referenced. * - * Mutexes created using this macro can be accessed using the xSemaphoreTake() + * Internally, within the FreeRTOS implementation, mutex semaphores use a block + * of memory, in which the mutex structure is stored. If a mutex is created + * using xSemaphoreCreateMutex() then the required memory is automatically + * dynamically allocated inside the xSemaphoreCreateMutex() function. (see + * http://www.freertos.org/a00111.html). If a mutex is created using + * xSemaphoreCreateMutexStatic() then the application writer must provided the + * memory. xSemaphoreCreateMutexStatic() therefore allows a mutex to be created + * without using any dynamic memory allocation. + * + * Mutexes created using this function can be accessed using the xSemaphoreTake() * and xSemaphoreGive() macros. The xSemaphoreTakeRecursive() and - * xSemaphoreGiveRecursive() macros should not be used. + * xSemaphoreGiveRecursive() macros must not be used. * * This type of semaphore uses a priority inheritance mechanism so a task * 'taking' a semaphore MUST ALWAYS 'give' the semaphore back once the @@ -662,13 +683,14 @@ typedef QueueHandle_t SemaphoreHandle_t; * * Mutex type semaphores cannot be used from within interrupt service routines. * - * See vSemaphoreCreateBinary() for an alternative implementation that can be + * See xSemaphoreCreateBinary() for an alternative implementation that can be * used for pure synchronisation (where one task or interrupt always 'gives' the * semaphore and another always 'takes' the semaphore) and from within interrupt * service routines. * - * @return xSemaphore Handle to the created mutex semaphore. Should be of type - * SemaphoreHandle_t. + * @return If the mutex was successfully created then a handle to the created + * semaphore is returned. If there was not enough heap to allocate the mutex + * data structures then NULL is returned. * * Example usage: 
@@ -687,22 +709,96 @@ typedef QueueHandle_t SemaphoreHandle_t;
     }
  }
- * \defgroup vSemaphoreCreateMutex vSemaphoreCreateMutex + * \defgroup xSemaphoreCreateMutex xSemaphoreCreateMutex * \ingroup Semaphores */ +#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) #define xSemaphoreCreateMutex() xQueueCreateMutex( queueQUEUE_TYPE_MUTEX ) +#endif + +/** + * semphr. h + * 
SemaphoreHandle_t xSemaphoreCreateMutexStatic( StaticSemaphore_t *pxMutexBuffer )
+ * + * Creates a new mutex type semaphore instance, and returns a handle by which + * the new mutex can be referenced. + * + * Internally, within the FreeRTOS implementation, mutex semaphores use a block + * of memory, in which the mutex structure is stored. If a mutex is created + * using xSemaphoreCreateMutex() then the required memory is automatically + * dynamically allocated inside the xSemaphoreCreateMutex() function. (see + * http://www.freertos.org/a00111.html). If a mutex is created using + * xSemaphoreCreateMutexStatic() then the application writer must provided the + * memory. xSemaphoreCreateMutexStatic() therefore allows a mutex to be created + * without using any dynamic memory allocation. + * + * Mutexes created using this function can be accessed using the xSemaphoreTake() + * and xSemaphoreGive() macros. The xSemaphoreTakeRecursive() and + * xSemaphoreGiveRecursive() macros must not be used. + * + * This type of semaphore uses a priority inheritance mechanism so a task + * 'taking' a semaphore MUST ALWAYS 'give' the semaphore back once the + * semaphore it is no longer required. + * + * Mutex type semaphores cannot be used from within interrupt service routines. + * + * See xSemaphoreCreateBinary() for an alternative implementation that can be + * used for pure synchronisation (where one task or interrupt always 'gives' the + * semaphore and another always 'takes' the semaphore) and from within interrupt + * service routines. + * + * @param pxMutexBuffer Must point to a variable of type StaticSemaphore_t, + * which will be used to hold the mutex's data structure, removing the need for + * the memory to be allocated dynamically. + * + * @return If the mutex was successfully created then a handle to the created + * mutex is returned. If pxMutexBuffer was NULL then NULL is returned. + * + * Example usage: + 
+ SemaphoreHandle_t xSemaphore;
+ StaticSemaphore_t xMutexBuffer;
+
+ void vATask( void * pvParameters )
+ {
+    // A mutex cannot be used before it has been created.  xMutexBuffer is
+    // into xSemaphoreCreateMutexStatic() so no dynamic memory allocation is
+    // attempted.
+    xSemaphore = xSemaphoreCreateMutexStatic( &xMutexBuffer );
+
+    // As no dynamic memory allocation was performed, xSemaphore cannot be NULL,
+    // so there is no need to check it.
+ }
+
+ * \defgroup xSemaphoreCreateMutexStatic xSemaphoreCreateMutexStatic + * \ingroup Semaphores + */ +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) +#define xSemaphoreCreateMutexStatic( pxMutexBuffer ) xQueueCreateMutexStatic( queueQUEUE_TYPE_MUTEX, ( pxMutexBuffer ) ) +#endif /* configSUPPORT_STATIC_ALLOCATION */ /** * semphr. h * 
SemaphoreHandle_t xSemaphoreCreateRecursiveMutex( void )
* - * Macro that implements a recursive mutex by using the existing queue - * mechanism. + * Creates a new recursive mutex type semaphore instance, and returns a handle + * by which the new recursive mutex can be referenced. + * + * Internally, within the FreeRTOS implementation, recursive mutexs use a block + * of memory, in which the mutex structure is stored. If a recursive mutex is + * created using xSemaphoreCreateRecursiveMutex() then the required memory is + * automatically dynamically allocated inside the + * xSemaphoreCreateRecursiveMutex() function. (see + * http://www.freertos.org/a00111.html). If a recursive mutex is created using + * xSemaphoreCreateRecursiveMutexStatic() then the application writer must + * provide the memory that will get used by the mutex. + * xSemaphoreCreateRecursiveMutexStatic() therefore allows a recursive mutex to + * be created without using any dynamic memory allocation. * * Mutexes created using this macro can be accessed using the * xSemaphoreTakeRecursive() and xSemaphoreGiveRecursive() macros. The - * xSemaphoreTake() and xSemaphoreGive() macros should not be used. + * xSemaphoreTake() and xSemaphoreGive() macros must not be used. * * A mutex used recursively can be 'taken' repeatedly by the owner. The mutex * doesn't become available again until the owner has called @@ -717,13 +813,13 @@ typedef QueueHandle_t SemaphoreHandle_t; * * Mutex type semaphores cannot be used from within interrupt service routines. * - * See vSemaphoreCreateBinary() for an alternative implementation that can be + * See xSemaphoreCreateBinary() for an alternative implementation that can be * used for pure synchronisation (where one task or interrupt always 'gives' the * semaphore and another always 'takes' the semaphore) and from within interrupt * service routines. * * @return xSemaphore Handle to the created mutex semaphore. Should be of type - * SemaphoreHandle_t. + * SemaphoreHandle_t. * * Example usage: 
@@ -742,17 +838,107 @@ typedef QueueHandle_t SemaphoreHandle_t;
     }
  }
- * \defgroup vSemaphoreCreateMutex vSemaphoreCreateMutex + * \defgroup xSemaphoreCreateRecursiveMutex xSemaphoreCreateRecursiveMutex * \ingroup Semaphores */ +#if( ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) && ( configUSE_RECURSIVE_MUTEXES == 1 ) ) #define xSemaphoreCreateRecursiveMutex() xQueueCreateMutex( queueQUEUE_TYPE_RECURSIVE_MUTEX ) +#endif + +/** + * semphr. h + * 
SemaphoreHandle_t xSemaphoreCreateRecursiveMutexStatic( StaticSemaphore_t *pxMutexBuffer )
+ * + * Creates a new recursive mutex type semaphore instance, and returns a handle + * by which the new recursive mutex can be referenced. + * + * Internally, within the FreeRTOS implementation, recursive mutexs use a block + * of memory, in which the mutex structure is stored. If a recursive mutex is + * created using xSemaphoreCreateRecursiveMutex() then the required memory is + * automatically dynamically allocated inside the + * xSemaphoreCreateRecursiveMutex() function. (see + * http://www.freertos.org/a00111.html). If a recursive mutex is created using + * xSemaphoreCreateRecursiveMutexStatic() then the application writer must + * provide the memory that will get used by the mutex. + * xSemaphoreCreateRecursiveMutexStatic() therefore allows a recursive mutex to + * be created without using any dynamic memory allocation. + * + * Mutexes created using this macro can be accessed using the + * xSemaphoreTakeRecursive() and xSemaphoreGiveRecursive() macros. The + * xSemaphoreTake() and xSemaphoreGive() macros must not be used. + * + * A mutex used recursively can be 'taken' repeatedly by the owner. The mutex + * doesn't become available again until the owner has called + * xSemaphoreGiveRecursive() for each successful 'take' request. For example, + * if a task successfully 'takes' the same mutex 5 times then the mutex will + * not be available to any other task until it has also 'given' the mutex back + * exactly five times. + * + * This type of semaphore uses a priority inheritance mechanism so a task + * 'taking' a semaphore MUST ALWAYS 'give' the semaphore back once the + * semaphore it is no longer required. + * + * Mutex type semaphores cannot be used from within interrupt service routines. + * + * See xSemaphoreCreateBinary() for an alternative implementation that can be + * used for pure synchronisation (where one task or interrupt always 'gives' the + * semaphore and another always 'takes' the semaphore) and from within interrupt + * service routines. + * + * @param pxMutexBuffer Must point to a variable of type StaticSemaphore_t, + * which will then be used to hold the recursive mutex's data structure, + * removing the need for the memory to be allocated dynamically. + * + * @return If the recursive mutex was successfully created then a handle to the + * created recursive mutex is returned. If pxMutexBuffer was NULL then NULL is + * returned. + * + * Example usage: + 
+ SemaphoreHandle_t xSemaphore;
+ StaticSemaphore_t xMutexBuffer;
+
+ void vATask( void * pvParameters )
+ {
+    // A recursive semaphore cannot be used before it is created.  Here a
+    // recursive mutex is created using xSemaphoreCreateRecursiveMutexStatic().
+    // The address of xMutexBuffer is passed into the function, and will hold
+    // the mutexes data structures - so no dynamic memory allocation will be
+    // attempted.
+    xSemaphore = xSemaphoreCreateRecursiveMutexStatic( &xMutexBuffer );
+
+    // As no dynamic memory allocation was performed, xSemaphore cannot be NULL,
+    // so there is no need to check it.
+ }
+
+ * \defgroup xSemaphoreCreateRecursiveMutexStatic xSemaphoreCreateRecursiveMutexStatic + * \ingroup Semaphores + */ +#if( ( configSUPPORT_STATIC_ALLOCATION == 1 ) && ( configUSE_RECURSIVE_MUTEXES == 1 ) ) +#define xSemaphoreCreateRecursiveMutexStatic( pxStaticSemaphore ) xQueueCreateMutexStatic( queueQUEUE_TYPE_RECURSIVE_MUTEX, pxStaticSemaphore ) +#endif /* configSUPPORT_STATIC_ALLOCATION */ /** * semphr. h * 
SemaphoreHandle_t xSemaphoreCreateCounting( UBaseType_t uxMaxCount, UBaseType_t uxInitialCount )
* - * Macro that creates a counting semaphore by using the existing - * queue mechanism. + * Creates a new counting semaphore instance, and returns a handle by which the + * new counting semaphore can be referenced. + * + * In many usage scenarios it is faster and more memory efficient to use a + * direct to task notification in place of a counting semaphore! + * http://www.freertos.org/RTOS-task-notifications.html + * + * Internally, within the FreeRTOS implementation, counting semaphores use a + * block of memory, in which the counting semaphore structure is stored. If a + * counting semaphore is created using xSemaphoreCreateCounting() then the + * required memory is automatically dynamically allocated inside the + * xSemaphoreCreateCounting() function. (see + * http://www.freertos.org/a00111.html). If a counting semaphore is created + * using xSemaphoreCreateCountingStatic() then the application writer can + * instead optionally provide the memory that will get used by the counting + * semaphore. xSemaphoreCreateCountingStatic() therefore allows a counting + * semaphore to be created without using any dynamic memory allocation. * * Counting semaphores are typically used for two things: * @@ -808,7 +994,94 @@ typedef QueueHandle_t SemaphoreHandle_t; * \defgroup xSemaphoreCreateCounting xSemaphoreCreateCounting * \ingroup Semaphores */ +#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) #define xSemaphoreCreateCounting( uxMaxCount, uxInitialCount ) xQueueCreateCountingSemaphore( ( uxMaxCount ), ( uxInitialCount ) ) +#endif + +/** + * semphr. h + * 
SemaphoreHandle_t xSemaphoreCreateCountingStatic( UBaseType_t uxMaxCount, UBaseType_t uxInitialCount, StaticSemaphore_t *pxSemaphoreBuffer )
+ * + * Creates a new counting semaphore instance, and returns a handle by which the + * new counting semaphore can be referenced. + * + * In many usage scenarios it is faster and more memory efficient to use a + * direct to task notification in place of a counting semaphore! + * http://www.freertos.org/RTOS-task-notifications.html + * + * Internally, within the FreeRTOS implementation, counting semaphores use a + * block of memory, in which the counting semaphore structure is stored. If a + * counting semaphore is created using xSemaphoreCreateCounting() then the + * required memory is automatically dynamically allocated inside the + * xSemaphoreCreateCounting() function. (see + * http://www.freertos.org/a00111.html). If a counting semaphore is created + * using xSemaphoreCreateCountingStatic() then the application writer must + * provide the memory. xSemaphoreCreateCountingStatic() therefore allows a + * counting semaphore to be created without using any dynamic memory allocation. + * + * Counting semaphores are typically used for two things: + * + * 1) Counting events. + * + * In this usage scenario an event handler will 'give' a semaphore each time + * an event occurs (incrementing the semaphore count value), and a handler + * task will 'take' a semaphore each time it processes an event + * (decrementing the semaphore count value). The count value is therefore + * the difference between the number of events that have occurred and the + * number that have been processed. In this case it is desirable for the + * initial count value to be zero. + * + * 2) Resource management. + * + * In this usage scenario the count value indicates the number of resources + * available. To obtain control of a resource a task must first obtain a + * semaphore - decrementing the semaphore count value. When the count value + * reaches zero there are no free resources. When a task finishes with the + * resource it 'gives' the semaphore back - incrementing the semaphore count + * value. In this case it is desirable for the initial count value to be + * equal to the maximum count value, indicating that all resources are free. + * + * @param uxMaxCount The maximum count value that can be reached. When the + * semaphore reaches this value it can no longer be 'given'. + * + * @param uxInitialCount The count value assigned to the semaphore when it is + * created. + * + * @param pxSemaphoreBuffer Must point to a variable of type StaticSemaphore_t, + * which will then be used to hold the semaphore's data structure, removing the + * need for the memory to be allocated dynamically. + * + * @return If the counting semaphore was successfully created then a handle to + * the created counting semaphore is returned. If pxSemaphoreBuffer was NULL + * then NULL is returned. + * + * Example usage: + 
+ SemaphoreHandle_t xSemaphore;
+ StaticSemaphore_t xSemaphoreBuffer;
+
+ void vATask( void * pvParameters )
+ {
+ SemaphoreHandle_t xSemaphore = NULL;
+
+    // Counting semaphore cannot be used before they have been created.  Create
+    // a counting semaphore using xSemaphoreCreateCountingStatic().  The max
+    // value to which the semaphore can count is 10, and the initial value
+    // assigned to the count will be 0.  The address of xSemaphoreBuffer is
+    // passed in and will be used to hold the semaphore structure, so no dynamic
+    // memory allocation will be used.
+    xSemaphore = xSemaphoreCreateCounting( 10, 0, &xSemaphoreBuffer );
+
+    // No memory allocation was attempted so xSemaphore cannot be NULL, so there
+    // is no need to check its value.
+ }
+
+ * \defgroup xSemaphoreCreateCountingStatic xSemaphoreCreateCountingStatic + * \ingroup Semaphores + */ +#if( configSUPPORT_STATIC_ALLOCATION == 1 ) +#define xSemaphoreCreateCountingStatic( uxMaxCount, uxInitialCount, pxSemaphoreBuffer ) xQueueCreateCountingSemaphoreStatic( ( uxMaxCount ), ( uxInitialCount ), ( pxSemaphoreBuffer ) ) +#endif /* configSUPPORT_STATIC_ALLOCATION */ /** * semphr. h @@ -839,6 +1112,29 @@ typedef QueueHandle_t SemaphoreHandle_t; */ #define xSemaphoreGetMutexHolder( xSemaphore ) xQueueGetMutexHolder( ( xSemaphore ) ) +/** + * semphr.h + * 
TaskHandle_t xSemaphoreGetMutexHolderFromISR( SemaphoreHandle_t xMutex );
+ * + * If xMutex is indeed a mutex type semaphore, return the current mutex holder. + * If xMutex is not a mutex type semaphore, or the mutex is available (not held + * by a task), return NULL. + * + */ +#define xSemaphoreGetMutexHolderFromISR( xSemaphore ) xQueueGetMutexHolderFromISR( ( xSemaphore ) ) + +/** + * semphr.h + * 
UBaseType_t uxSemaphoreGetCount( SemaphoreHandle_t xSemaphore );
+ * + * If the semaphore is a counting semaphore then uxSemaphoreGetCount() returns + * its current count value. If the semaphore is a binary semaphore then + * uxSemaphoreGetCount() returns 1 if the semaphore is available, and 0 if the + * semaphore is not available. + * + */ +#define uxSemaphoreGetCount( xSemaphore ) uxQueueMessagesWaiting( ( QueueHandle_t ) ( xSemaphore ) ) + #endif /* SEMAPHORE_H */ diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/stack_macros.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/stack_macros.h new file mode 100644 index 00000000..84b953d9 --- /dev/null +++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/stack_macros.h @@ -0,0 +1,129 @@ +/* + * FreeRTOS Kernel V10.0.1 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ + +#ifndef STACK_MACROS_H +#define STACK_MACROS_H + +/* + * Call the stack overflow hook function if the stack of the task being swapped + * out is currently overflowed, or looks like it might have overflowed in the + * past. + * + * Setting configCHECK_FOR_STACK_OVERFLOW to 1 will cause the macro to check + * the current stack state only - comparing the current top of stack value to + * the stack limit. Setting configCHECK_FOR_STACK_OVERFLOW to greater than 1 + * will also cause the last few stack bytes to be checked to ensure the value + * to which the bytes were set when the task was created have not been + * overwritten. Note this second test does not guarantee that an overflowed + * stack will always be recognised. + */ + +/*-----------------------------------------------------------*/ + +#if( ( configCHECK_FOR_STACK_OVERFLOW == 1 ) && ( portSTACK_GROWTH < 0 ) ) + +/* Only the current stack state is to be checked. */ +#define taskCHECK_FOR_STACK_OVERFLOW() \ + { \ + /* Is the currently saved stack pointer within the stack limit? */ \ + if( pxCurrentTCB->pxTopOfStack <= pxCurrentTCB->pxStack ) \ + { \ + vApplicationStackOverflowHook( ( TaskHandle_t ) pxCurrentTCB, pxCurrentTCB->pcTaskName ); \ + } \ + } + +#endif /* configCHECK_FOR_STACK_OVERFLOW == 1 */ +/*-----------------------------------------------------------*/ + +#if( ( configCHECK_FOR_STACK_OVERFLOW == 1 ) && ( portSTACK_GROWTH > 0 ) ) + +/* Only the current stack state is to be checked. */ +#define taskCHECK_FOR_STACK_OVERFLOW() \ + { \ + \ + /* Is the currently saved stack pointer within the stack limit? */ \ + if( pxCurrentTCB->pxTopOfStack >= pxCurrentTCB->pxEndOfStack ) \ + { \ + vApplicationStackOverflowHook( ( TaskHandle_t ) pxCurrentTCB, pxCurrentTCB->pcTaskName ); \ + } \ + } + +#endif /* configCHECK_FOR_STACK_OVERFLOW == 1 */ +/*-----------------------------------------------------------*/ + +#if( ( configCHECK_FOR_STACK_OVERFLOW > 1 ) && ( portSTACK_GROWTH < 0 ) ) + +#define taskCHECK_FOR_STACK_OVERFLOW() \ + { \ + const uint32_t * const pulStack = ( uint32_t * ) pxCurrentTCB->pxStack; \ + const uint32_t ulCheckValue = ( uint32_t ) 0xa5a5a5a5; \ + \ + if( ( pulStack[ 0 ] != ulCheckValue ) || \ + ( pulStack[ 1 ] != ulCheckValue ) || \ + ( pulStack[ 2 ] != ulCheckValue ) || \ + ( pulStack[ 3 ] != ulCheckValue ) ) \ + { \ + vApplicationStackOverflowHook( ( TaskHandle_t ) pxCurrentTCB, pxCurrentTCB->pcTaskName ); \ + } \ + } + +#endif /* #if( configCHECK_FOR_STACK_OVERFLOW > 1 ) */ +/*-----------------------------------------------------------*/ + +#if( ( configCHECK_FOR_STACK_OVERFLOW > 1 ) && ( portSTACK_GROWTH > 0 ) ) + +#define taskCHECK_FOR_STACK_OVERFLOW() \ + { \ + int8_t *pcEndOfStack = ( int8_t * ) pxCurrentTCB->pxEndOfStack; \ + static const uint8_t ucExpectedStackBytes[] = { tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, \ + tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, \ + tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, \ + tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, \ + tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE }; \ + \ + \ + pcEndOfStack -= sizeof( ucExpectedStackBytes ); \ + \ + /* Has the extremity of the task stack ever been written over? */ \ + if( memcmp( ( void * ) pcEndOfStack, ( void * ) ucExpectedStackBytes, sizeof( ucExpectedStackBytes ) ) != 0 ) \ + { \ + vApplicationStackOverflowHook( ( TaskHandle_t ) pxCurrentTCB, pxCurrentTCB->pcTaskName ); \ + } \ + } + +#endif /* #if( configCHECK_FOR_STACK_OVERFLOW > 1 ) */ +/*-----------------------------------------------------------*/ + +/* Remove stack overflow macro if not being used. */ +#ifndef taskCHECK_FOR_STACK_OVERFLOW +#define taskCHECK_FOR_STACK_OVERFLOW() +#endif + + + +#endif /* STACK_MACROS_H */ + diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/stream_buffer.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/stream_buffer.h new file mode 100644 index 00000000..ea1bd66d --- /dev/null +++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/stream_buffer.h @@ -0,0 +1,852 @@ +/* + * FreeRTOS Kernel V10.0.1 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ + +/* + * Stream buffers are used to send a continuous stream of data from one task or + * interrupt to another. Their implementation is light weight, making them + * particularly suited for interrupt to task and core to core communication + * scenarios. + * + * ***NOTE***: Uniquely among FreeRTOS objects, the stream buffer + * implementation (so also the message buffer implementation, as message buffers + * are built on top of stream buffers) assumes there is only one task or + * interrupt that will write to the buffer (the writer), and only one task or + * interrupt that will read from the buffer (the reader). It is safe for the + * writer and reader to be different tasks or interrupts, but, unlike other + * FreeRTOS objects, it is not safe to have multiple different writers or + * multiple different readers. If there are to be multiple different writers + * then the application writer must place each call to a writing API function + * (such as xStreamBufferSend()) inside a critical section and set the send + * block time to 0. Likewise, if there are to be multiple different readers + * then the application writer must place each call to a reading API function + * (such as xStreamBufferRead()) inside a critical section section and set the + * receive block time to 0. + * + */ + +#ifndef STREAM_BUFFER_H +#define STREAM_BUFFER_H + +#if defined( __cplusplus ) +extern "C" { +#endif + +/** + * Type by which stream buffers are referenced. For example, a call to + * xStreamBufferCreate() returns an StreamBufferHandle_t variable that can + * then be used as a parameter to xStreamBufferSend(), xStreamBufferReceive(), + * etc. + */ +typedef void* StreamBufferHandle_t; + + +/** + * message_buffer.h + * +
+StreamBufferHandle_t xStreamBufferCreate( size_t xBufferSizeBytes, size_t xTriggerLevelBytes );
+
+ * + * Creates a new stream buffer using dynamically allocated memory. See + * xStreamBufferCreateStatic() for a version that uses statically allocated + * memory (memory that is allocated at compile time). + * + * configSUPPORT_DYNAMIC_ALLOCATION must be set to 1 or left undefined in + * FreeRTOSConfig.h for xStreamBufferCreate() to be available. + * + * @param xBufferSizeBytes The total number of bytes the stream buffer will be + * able to hold at any one time. + * + * @param xTriggerLevelBytes The number of bytes that must be in the stream + * buffer before a task that is blocked on the stream buffer to wait for data is + * moved out of the blocked state. For example, if a task is blocked on a read + * of an empty stream buffer that has a trigger level of 1 then the task will be + * unblocked when a single byte is written to the buffer or the task's block + * time expires. As another example, if a task is blocked on a read of an empty + * stream buffer that has a trigger level of 10 then the task will not be + * unblocked until the stream buffer contains at least 10 bytes or the task's + * block time expires. If a reading task's block time expires before the + * trigger level is reached then the task will still receive however many bytes + * are actually available. Setting a trigger level of 0 will result in a + * trigger level of 1 being used. It is not valid to specify a trigger level + * that is greater than the buffer size. + * + * @return If NULL is returned, then the stream buffer cannot be created + * because there is insufficient heap memory available for FreeRTOS to allocate + * the stream buffer data structures and storage area. A non-NULL value being + * returned indicates that the stream buffer has been created successfully - + * the returned value should be stored as the handle to the created stream + * buffer. + * + * Example use: +
+
+void vAFunction( void )
+{
+StreamBufferHandle_t xStreamBuffer;
+const size_t xStreamBufferSizeBytes = 100, xTriggerLevel = 10;
+
+    // Create a stream buffer that can hold 100 bytes.  The memory used to hold
+    // both the stream buffer structure and the data in the stream buffer is
+    // allocated dynamically.
+    xStreamBuffer = xStreamBufferCreate( xStreamBufferSizeBytes, xTriggerLevel );
+
+    if( xStreamBuffer == NULL )
+    {
+        // There was not enough heap memory space available to create the
+        // stream buffer.
+    }
+    else
+    {
+        // The stream buffer was created successfully and can now be used.
+    }
+}
+
+ * \defgroup xStreamBufferCreate xStreamBufferCreate + * \ingroup StreamBufferManagement + */ +#define xStreamBufferCreate( xBufferSizeBytes, xTriggerLevelBytes ) xStreamBufferGenericCreate( xBufferSizeBytes, xTriggerLevelBytes, pdFALSE ) + +/** + * stream_buffer.h + * +
+StreamBufferHandle_t xStreamBufferCreateStatic( size_t xBufferSizeBytes,
+                                                size_t xTriggerLevelBytes,
+                                                uint8_t *pucStreamBufferStorageArea,
+                                                StaticStreamBuffer_t *pxStaticStreamBuffer );
+
+ * Creates a new stream buffer using statically allocated memory. See + * xStreamBufferCreate() for a version that uses dynamically allocated memory. + * + * configSUPPORT_STATIC_ALLOCATION must be set to 1 in FreeRTOSConfig.h for + * xStreamBufferCreateStatic() to be available. + * + * @param xBufferSizeBytes The size, in bytes, of the buffer pointed to by the + * pucStreamBufferStorageArea parameter. + * + * @param xTriggerLevelBytes The number of bytes that must be in the stream + * buffer before a task that is blocked on the stream buffer to wait for data is + * moved out of the blocked state. For example, if a task is blocked on a read + * of an empty stream buffer that has a trigger level of 1 then the task will be + * unblocked when a single byte is written to the buffer or the task's block + * time expires. As another example, if a task is blocked on a read of an empty + * stream buffer that has a trigger level of 10 then the task will not be + * unblocked until the stream buffer contains at least 10 bytes or the task's + * block time expires. If a reading task's block time expires before the + * trigger level is reached then the task will still receive however many bytes + * are actually available. Setting a trigger level of 0 will result in a + * trigger level of 1 being used. It is not valid to specify a trigger level + * that is greater than the buffer size. + * + * @param pucStreamBufferStorageArea Must point to a uint8_t array that is at + * least xBufferSizeBytes + 1 big. This is the array to which streams are + * copied when they are written to the stream buffer. + * + * @param pxStaticStreamBuffer Must point to a variable of type + * StaticStreamBuffer_t, which will be used to hold the stream buffer's data + * structure. + * + * @return If the stream buffer is created successfully then a handle to the + * created stream buffer is returned. If either pucStreamBufferStorageArea or + * pxStaticstreamBuffer are NULL then NULL is returned. + * + * Example use: +
+
+// Used to dimension the array used to hold the streams.  The available space
+// will actually be one less than this, so 999.
+#define STORAGE_SIZE_BYTES 1000
+
+// Defines the memory that will actually hold the streams within the stream
+// buffer.
+static uint8_t ucStorageBuffer[ STORAGE_SIZE_BYTES ];
+
+// The variable used to hold the stream buffer structure.
+StaticStreamBuffer_t xStreamBufferStruct;
+
+void MyFunction( void )
+{
+StreamBufferHandle_t xStreamBuffer;
+const size_t xTriggerLevel = 1;
+
+    xStreamBuffer = xStreamBufferCreateStatic( sizeof( ucBufferStorage ),
+                                               xTriggerLevel,
+                                               ucBufferStorage,
+                                               &xStreamBufferStruct );
+
+    // As neither the pucStreamBufferStorageArea or pxStaticStreamBuffer
+    // parameters were NULL, xStreamBuffer will not be NULL, and can be used to
+    // reference the created stream buffer in other stream buffer API calls.
+
+    // Other code that uses the stream buffer can go here.
+}
+
+
+ * \defgroup xStreamBufferCreateStatic xStreamBufferCreateStatic + * \ingroup StreamBufferManagement + */ +#define xStreamBufferCreateStatic( xBufferSizeBytes, xTriggerLevelBytes, pucStreamBufferStorageArea, pxStaticStreamBuffer ) xStreamBufferGenericCreateStatic( xBufferSizeBytes, xTriggerLevelBytes, pdFALSE, pucStreamBufferStorageArea, pxStaticStreamBuffer ) + +/** + * stream_buffer.h + * +
+size_t xStreamBufferSend( StreamBufferHandle_t xStreamBuffer,
+                          const void *pvTxData,
+                          size_t xDataLengthBytes,
+                          TickType_t xTicksToWait );
+
+ *
+ * Sends bytes to a stream buffer.  The bytes are copied into the stream buffer.
+ *
+ * ***NOTE***:  Uniquely among FreeRTOS objects, the stream buffer
+ * implementation (so also the message buffer implementation, as message buffers
+ * are built on top of stream buffers) assumes there is only one task or
+ * interrupt that will write to the buffer (the writer), and only one task or
+ * interrupt that will read from the buffer (the reader).  It is safe for the
+ * writer and reader to be different tasks or interrupts, but, unlike other
+ * FreeRTOS objects, it is not safe to have multiple different writers or
+ * multiple different readers.  If there are to be multiple different writers
+ * then the application writer must place each call to a writing API function
+ * (such as xStreamBufferSend()) inside a critical section and set the send
+ * block time to 0.  Likewise, if there are to be multiple different readers
+ * then the application writer must place each call to a reading API function
+ * (such as xStreamBufferRead()) inside a critical section and set the receive
+ * block time to 0.
+ *
+ * Use xStreamBufferSend() to write to a stream buffer from a task.  Use
+ * xStreamBufferSendFromISR() to write to a stream buffer from an interrupt
+ * service routine (ISR).
+ *
+ * @param xStreamBuffer The handle of the stream buffer to which a stream is
+ * being sent.
+ *
+ * @param pvTxData A pointer to the buffer that holds the bytes to be copied
+ * into the stream buffer.
+ *
+ * @param xDataLengthBytes   The maximum number of bytes to copy from pvTxData
+ * into the stream buffer.
+ *
+ * @param xTicksToWait The maximum amount of time the task should remain in the
+ * Blocked state to wait for enough space to become available in the stream
+ * buffer, should the stream buffer contain too little space to hold the
+ * another xDataLengthBytes bytes.  The block time is specified in tick periods,
+ * so the absolute time it represents is dependent on the tick frequency.  The
+ * macro pdMS_TO_TICKS() can be used to convert a time specified in milliseconds
+ * into a time specified in ticks.  Setting xTicksToWait to portMAX_DELAY will
+ * cause the task to wait indefinitely (without timing out), provided
+ * INCLUDE_vTaskSuspend is set to 1 in FreeRTOSConfig.h.  If a task times out
+ * before it can write all xDataLengthBytes into the buffer it will still write
+ * as many bytes as possible.  A task does not use any CPU time when it is in
+ * the blocked state.
+ *
+ * @return The number of bytes written to the stream buffer.  If a task times
+ * out before it can write all xDataLengthBytes into the buffer it will still
+ * write as many bytes as possible.
+ *
+ * Example use:
+
+void vAFunction( StreamBufferHandle_t xStreamBuffer )
+{
+size_t xBytesSent;
+uint8_t ucArrayToSend[] = { 0, 1, 2, 3 };
+char *pcStringToSend = "String to send";
+const TickType_t x100ms = pdMS_TO_TICKS( 100 );
+
+    // Send an array to the stream buffer, blocking for a maximum of 100ms to
+    // wait for enough space to be available in the stream buffer.
+    xBytesSent = xStreamBufferSend( xStreamBuffer, ( void * ) ucArrayToSend, sizeof( ucArrayToSend ), x100ms );
+
+    if( xBytesSent != sizeof( ucArrayToSend ) )
+    {
+        // The call to xStreamBufferSend() times out before there was enough
+        // space in the buffer for the data to be written, but it did
+        // successfully write xBytesSent bytes.
+    }
+
+    // Send the string to the stream buffer.  Return immediately if there is not
+    // enough space in the buffer.
+    xBytesSent = xStreamBufferSend( xStreamBuffer, ( void * ) pcStringToSend, strlen( pcStringToSend ), 0 );
+
+    if( xBytesSent != strlen( pcStringToSend ) )
+    {
+        // The entire string could not be added to the stream buffer because
+        // there was not enough free space in the buffer, but xBytesSent bytes
+        // were sent.  Could try again to send the remaining bytes.
+    }
+}
+

+ * \defgroup xStreamBufferSend xStreamBufferSend
+ * \ingroup StreamBufferManagement
+ */
+size_t xStreamBufferSend( StreamBufferHandle_t xStreamBuffer,
+                          const void* pvTxData,
+                          size_t xDataLengthBytes,
+                          TickType_t xTicksToWait ) PRIVILEGED_FUNCTION;
+
+/**
+ * stream_buffer.h
+ *
+
+size_t xStreamBufferSendFromISR( StreamBufferHandle_t xStreamBuffer,
+                                 const void *pvTxData,
+                                 size_t xDataLengthBytes,
+                                 BaseType_t *pxHigherPriorityTaskWoken );
+
+ *
+ * Interrupt safe version of the API function that sends a stream of bytes to
+ * the stream buffer.
+ *
+ * ***NOTE***:  Uniquely among FreeRTOS objects, the stream buffer
+ * implementation (so also the message buffer implementation, as message buffers
+ * are built on top of stream buffers) assumes there is only one task or
+ * interrupt that will write to the buffer (the writer), and only one task or
+ * interrupt that will read from the buffer (the reader).  It is safe for the
+ * writer and reader to be different tasks or interrupts, but, unlike other
+ * FreeRTOS objects, it is not safe to have multiple different writers or
+ * multiple different readers.  If there are to be multiple different writers
+ * then the application writer must place each call to a writing API function
+ * (such as xStreamBufferSend()) inside a critical section and set the send
+ * block time to 0.  Likewise, if there are to be multiple different readers
+ * then the application writer must place each call to a reading API function
+ * (such as xStreamBufferRead()) inside a critical section and set the receive
+ * block time to 0.
+ *
+ * Use xStreamBufferSend() to write to a stream buffer from a task.  Use
+ * xStreamBufferSendFromISR() to write to a stream buffer from an interrupt
+ * service routine (ISR).
+ *
+ * @param xStreamBuffer The handle of the stream buffer to which a stream is
+ * being sent.
+ *
+ * @param pvTxData A pointer to the data that is to be copied into the stream
+ * buffer.
+ *
+ * @param xDataLengthBytes The maximum number of bytes to copy from pvTxData
+ * into the stream buffer.
+ *
+ * @param pxHigherPriorityTaskWoken  It is possible that a stream buffer will
+ * have a task blocked on it waiting for data.  Calling
+ * xStreamBufferSendFromISR() can make data available, and so cause a task that
+ * was waiting for data to leave the Blocked state.  If calling
+ * xStreamBufferSendFromISR() causes a task to leave the Blocked state, and the
+ * unblocked task has a priority higher than the currently executing task (the
+ * task that was interrupted), then, internally, xStreamBufferSendFromISR()
+ * will set *pxHigherPriorityTaskWoken to pdTRUE.  If
+ * xStreamBufferSendFromISR() sets this value to pdTRUE, then normally a
+ * context switch should be performed before the interrupt is exited.  This will
+ * ensure that the interrupt returns directly to the highest priority Ready
+ * state task.  *pxHigherPriorityTaskWoken should be set to pdFALSE before it
+ * is passed into the function.  See the example code below for an example.
+ *
+ * @return The number of bytes actually written to the stream buffer, which will
+ * be less than xDataLengthBytes if the stream buffer didn't have enough free
+ * space for all the bytes to be written.
+ *
+ * Example use:
+
+// A stream buffer that has already been created.
+StreamBufferHandle_t xStreamBuffer;
+
+void vAnInterruptServiceRoutine( void )
+{
+size_t xBytesSent;
+char *pcStringToSend = "String to send";
+BaseType_t xHigherPriorityTaskWoken = pdFALSE; // Initialised to pdFALSE.
+
+    // Attempt to send the string to the stream buffer.
+    xBytesSent = xStreamBufferSendFromISR( xStreamBuffer,
+                                           ( void * ) pcStringToSend,
+                                           strlen( pcStringToSend ),
+                                           &xHigherPriorityTaskWoken );
+
+    if( xBytesSent != strlen( pcStringToSend ) )
+    {
+        // There was not enough free space in the stream buffer for the entire
+        // string to be written, ut xBytesSent bytes were written.
+    }
+
+    // If xHigherPriorityTaskWoken was set to pdTRUE inside
+    // xStreamBufferSendFromISR() then a task that has a priority above the
+    // priority of the currently executing task was unblocked and a context
+    // switch should be performed to ensure the ISR returns to the unblocked
+    // task.  In most FreeRTOS ports this is done by simply passing
+    // xHigherPriorityTaskWoken into taskYIELD_FROM_ISR(), which will test the
+    // variables value, and perform the context switch if necessary.  Check the
+    // documentation for the port in use for port specific instructions.
+    taskYIELD_FROM_ISR( xHigherPriorityTaskWoken );
+}
+

+ * \defgroup xStreamBufferSendFromISR xStreamBufferSendFromISR
+ * \ingroup StreamBufferManagement
+ */
+size_t xStreamBufferSendFromISR( StreamBufferHandle_t xStreamBuffer,
+                                 const void* pvTxData,
+                                 size_t xDataLengthBytes,
+                                 BaseType_t* const pxHigherPriorityTaskWoken ) PRIVILEGED_FUNCTION;
+
+/**
+ * stream_buffer.h
+ *
+
+size_t xStreamBufferReceive( StreamBufferHandle_t xStreamBuffer,
+                             void *pvRxData,
+                             size_t xBufferLengthBytes,
+                             TickType_t xTicksToWait );
+

+ *
+ * Receives bytes from a stream buffer.
+ *
+ * ***NOTE***:  Uniquely among FreeRTOS objects, the stream buffer
+ * implementation (so also the message buffer implementation, as message buffers
+ * are built on top of stream buffers) assumes there is only one task or
+ * interrupt that will write to the buffer (the writer), and only one task or
+ * interrupt that will read from the buffer (the reader).  It is safe for the
+ * writer and reader to be different tasks or interrupts, but, unlike other
+ * FreeRTOS objects, it is not safe to have multiple different writers or
+ * multiple different readers.  If there are to be multiple different writers
+ * then the application writer must place each call to a writing API function
+ * (such as xStreamBufferSend()) inside a critical section and set the send
+ * block time to 0.  Likewise, if there are to be multiple different readers
+ * then the application writer must place each call to a reading API function
+ * (such as xStreamBufferRead()) inside a critical section and set the receive
+ * block time to 0.
+ *
+ * Use xStreamBufferReceive() to read from a stream buffer from a task.  Use
+ * xStreamBufferReceiveFromISR() to read from a stream buffer from an
+ * interrupt service routine (ISR).
+ *
+ * @param xStreamBuffer The handle of the stream buffer from which bytes are to
+ * be received.
+ *
+ * @param pvRxData A pointer to the buffer into which the received bytes will be
+ * copied.
+ *
+ * @param xBufferLengthBytes The length of the buffer pointed to by the
+ * pvRxData parameter.  This sets the maximum number of bytes to receive in one
+ * call.  xStreamBufferReceive will return as many bytes as possible up to a
+ * maximum set by xBufferLengthBytes.
+ *
+ * @param xTicksToWait The maximum amount of time the task should remain in the
+ * Blocked state to wait for data to become available if the stream buffer is
+ * empty.  xStreamBufferReceive() will return immediately if xTicksToWait is
+ * zero.  The block time is specified in tick periods, so the absolute time it
+ * represents is dependent on the tick frequency.  The macro pdMS_TO_TICKS() can
+ * be used to convert a time specified in milliseconds into a time specified in
+ * ticks.  Setting xTicksToWait to portMAX_DELAY will cause the task to wait
+ * indefinitely (without timing out), provided INCLUDE_vTaskSuspend is set to 1
+ * in FreeRTOSConfig.h.  A task does not use any CPU time when it is in the
+ * Blocked state.
+ *
+ * @return The number of bytes actually read from the stream buffer, which will
+ * be less than xBufferLengthBytes if the call to xStreamBufferReceive() timed
+ * out before xBufferLengthBytes were available.
+ *
+ * Example use:
+
+void vAFunction( StreamBuffer_t xStreamBuffer )
+{
+uint8_t ucRxData[ 20 ];
+size_t xReceivedBytes;
+const TickType_t xBlockTime = pdMS_TO_TICKS( 20 );
+
+    // Receive up to another sizeof( ucRxData ) bytes from the stream buffer.
+    // Wait in the Blocked state (so not using any CPU processing time) for a
+    // maximum of 100ms for the full sizeof( ucRxData ) number of bytes to be
+    // available.
+    xReceivedBytes = xStreamBufferReceive( xStreamBuffer,
+                                           ( void * ) ucRxData,
+                                           sizeof( ucRxData ),
+                                           xBlockTime );
+
+    if( xReceivedBytes > 0 )
+    {
+        // A ucRxData contains another xRecievedBytes bytes of data, which can
+        // be processed here....
+    }
+}
+

+ * \defgroup xStreamBufferReceive xStreamBufferReceive
+ * \ingroup StreamBufferManagement
+ */
+size_t xStreamBufferReceive( StreamBufferHandle_t xStreamBuffer,
+                             void* pvRxData,
+                             size_t xBufferLengthBytes,
+                             TickType_t xTicksToWait ) PRIVILEGED_FUNCTION;
+
+/**
+ * stream_buffer.h
+ *
+
+size_t xStreamBufferReceiveFromISR( StreamBufferHandle_t xStreamBuffer,
+                                    void *pvRxData,
+                                    size_t xBufferLengthBytes,
+                                    BaseType_t *pxHigherPriorityTaskWoken );
+

+ *
+ * An interrupt safe version of the API function that receives bytes from a
+ * stream buffer.
+ *
+ * Use xStreamBufferReceive() to read bytes from a stream buffer from a task.
+ * Use xStreamBufferReceiveFromISR() to read bytes from a stream buffer from an
+ * interrupt service routine (ISR).
+ *
+ * @param xStreamBuffer The handle of the stream buffer from which a stream
+ * is being received.
+ *
+ * @param pvRxData A pointer to the buffer into which the received bytes are
+ * copied.
+ *
+ * @param xBufferLengthBytes The length of the buffer pointed to by the
+ * pvRxData parameter.  This sets the maximum number of bytes to receive in one
+ * call.  xStreamBufferReceive will return as many bytes as possible up to a
+ * maximum set by xBufferLengthBytes.
+ *
+ * @param pxHigherPriorityTaskWoken  It is possible that a stream buffer will
+ * have a task blocked on it waiting for space to become available.  Calling
+ * xStreamBufferReceiveFromISR() can make space available, and so cause a task
+ * that is waiting for space to leave the Blocked state.  If calling
+ * xStreamBufferReceiveFromISR() causes a task to leave the Blocked state, and
+ * the unblocked task has a priority higher than the currently executing task
+ * (the task that was interrupted), then, internally,
+ * xStreamBufferReceiveFromISR() will set *pxHigherPriorityTaskWoken to pdTRUE.
+ * If xStreamBufferReceiveFromISR() sets this value to pdTRUE, then normally a
+ * context switch should be performed before the interrupt is exited.  That will
+ * ensure the interrupt returns directly to the highest priority Ready state
+ * task.  *pxHigherPriorityTaskWoken should be set to pdFALSE before it is
+ * passed into the function.  See the code example below for an example.
+ *
+ * @return The number of bytes read from the stream buffer, if any.
+ *
+ * Example use:
+
+// A stream buffer that has already been created.
+StreamBuffer_t xStreamBuffer;
+
+void vAnInterruptServiceRoutine( void )
+{
+uint8_t ucRxData[ 20 ];
+size_t xReceivedBytes;
+BaseType_t xHigherPriorityTaskWoken = pdFALSE;  // Initialised to pdFALSE.
+
+    // Receive the next stream from the stream buffer.
+    xReceivedBytes = xStreamBufferReceiveFromISR( xStreamBuffer,
+                                                  ( void * ) ucRxData,
+                                                  sizeof( ucRxData ),
+                                                  &xHigherPriorityTaskWoken );
+
+    if( xReceivedBytes > 0 )
+    {
+        // ucRxData contains xReceivedBytes read from the stream buffer.
+        // Process the stream here....
+    }
+
+    // If xHigherPriorityTaskWoken was set to pdTRUE inside
+    // xStreamBufferReceiveFromISR() then a task that has a priority above the
+    // priority of the currently executing task was unblocked and a context
+    // switch should be performed to ensure the ISR returns to the unblocked
+    // task.  In most FreeRTOS ports this is done by simply passing
+    // xHigherPriorityTaskWoken into taskYIELD_FROM_ISR(), which will test the
+    // variables value, and perform the context switch if necessary.  Check the
+    // documentation for the port in use for port specific instructions.
+    taskYIELD_FROM_ISR( xHigherPriorityTaskWoken );
+}
+

+ * \defgroup xStreamBufferReceiveFromISR xStreamBufferReceiveFromISR
+ * \ingroup StreamBufferManagement
+ */
+size_t xStreamBufferReceiveFromISR( StreamBufferHandle_t xStreamBuffer,
+                                    void* pvRxData,
+                                    size_t xBufferLengthBytes,
+                                    BaseType_t* const pxHigherPriorityTaskWoken ) PRIVILEGED_FUNCTION;
+
+/**
+ * stream_buffer.h
+ *
+
+void vStreamBufferDelete( StreamBufferHandle_t xStreamBuffer );
+

+ *
+ * Deletes a stream buffer that was previously created using a call to
+ * xStreamBufferCreate() or xStreamBufferCreateStatic().  If the stream
+ * buffer was created using dynamic memory (that is, by xStreamBufferCreate()),
+ * then the allocated memory is freed.
+ *
+ * A stream buffer handle must not be used after the stream buffer has been
+ * deleted.
+ *
+ * @param xStreamBuffer The handle of the stream buffer to be deleted.
+ *
+ * \defgroup vStreamBufferDelete vStreamBufferDelete
+ * \ingroup StreamBufferManagement
+ */
+void vStreamBufferDelete( StreamBufferHandle_t xStreamBuffer ) PRIVILEGED_FUNCTION;
+
+/**
+ * stream_buffer.h
+ *
+
+BaseType_t xStreamBufferIsFull( StreamBufferHandle_t xStreamBuffer );
+

+ *
+ * Queries a stream buffer to see if it is full.  A stream buffer is full if it
+ * does not have any free space, and therefore cannot accept any more data.
+ *
+ * @param xStreamBuffer The handle of the stream buffer being queried.
+ *
+ * @return If the stream buffer is full then pdTRUE is returned.  Otherwise
+ * pdFALSE is returned.
+ *
+ * \defgroup xStreamBufferIsFull xStreamBufferIsFull
+ * \ingroup StreamBufferManagement
+ */
+BaseType_t xStreamBufferIsFull( StreamBufferHandle_t xStreamBuffer ) PRIVILEGED_FUNCTION;
+
+/**
+ * stream_buffer.h
+ *
+
+BaseType_t xStreamBufferIsEmpty( StreamBufferHandle_t xStreamBuffer );
+

+ *
+ * Queries a stream buffer to see if it is empty.  A stream buffer is empty if
+ * it does not contain any data.
+ *
+ * @param xStreamBuffer The handle of the stream buffer being queried.
+ *
+ * @return If the stream buffer is empty then pdTRUE is returned.  Otherwise
+ * pdFALSE is returned.
+ *
+ * \defgroup xStreamBufferIsEmpty xStreamBufferIsEmpty
+ * \ingroup StreamBufferManagement
+ */
+BaseType_t xStreamBufferIsEmpty( StreamBufferHandle_t xStreamBuffer ) PRIVILEGED_FUNCTION;
+
+/**
+ * stream_buffer.h
+ *
+
+BaseType_t xStreamBufferReset( StreamBufferHandle_t xStreamBuffer );
+

+ *
+ * Resets a stream buffer to its initial, empty, state.  Any data that was in
+ * the stream buffer is discarded.  A stream buffer can only be reset if there
+ * are no tasks blocked waiting to either send to or receive from the stream
+ * buffer.
+ *
+ * @param xStreamBuffer The handle of the stream buffer being reset.
+ *
+ * @return If the stream buffer is reset then pdPASS is returned.  If there was
+ * a task blocked waiting to send to or read from the stream buffer then the
+ * stream buffer is not reset and pdFAIL is returned.
+ *
+ * \defgroup xStreamBufferReset xStreamBufferReset
+ * \ingroup StreamBufferManagement
+ */
+BaseType_t xStreamBufferReset( StreamBufferHandle_t xStreamBuffer ) PRIVILEGED_FUNCTION;
+
+/**
+ * stream_buffer.h
+ *
+
+size_t xStreamBufferSpacesAvailable( StreamBufferHandle_t xStreamBuffer );
+

+ *
+ * Queries a stream buffer to see how much free space it contains, which is
+ * equal to the amount of data that can be sent to the stream buffer before it
+ * is full.
+ *
+ * @param xStreamBuffer The handle of the stream buffer being queried.
+ *
+ * @return The number of bytes that can be written to the stream buffer before
+ * the stream buffer would be full.
+ *
+ * \defgroup xStreamBufferSpacesAvailable xStreamBufferSpacesAvailable
+ * \ingroup StreamBufferManagement
+ */
+size_t xStreamBufferSpacesAvailable( StreamBufferHandle_t xStreamBuffer ) PRIVILEGED_FUNCTION;
+
+/**
+ * stream_buffer.h
+ *
+
+size_t xStreamBufferBytesAvailable( StreamBufferHandle_t xStreamBuffer );
+

+ *
+ * Queries a stream buffer to see how much data it contains, which is equal to
+ * the number of bytes that can be read from the stream buffer before the stream
+ * buffer would be empty.
+ *
+ * @param xStreamBuffer The handle of the stream buffer being queried.
+ *
+ * @return The number of bytes that can be read from the stream buffer before
+ * the stream buffer would be empty.
+ *
+ * \defgroup xStreamBufferBytesAvailable xStreamBufferBytesAvailable
+ * \ingroup StreamBufferManagement
+ */
+size_t xStreamBufferBytesAvailable( StreamBufferHandle_t xStreamBuffer ) PRIVILEGED_FUNCTION;
+
+/**
+ * stream_buffer.h
+ *
+
+BaseType_t xStreamBufferSetTriggerLevel( StreamBufferHandle_t xStreamBuffer, size_t xTriggerLevel );
+

+ *
+ * A stream buffer's trigger level is the number of bytes that must be in the
+ * stream buffer before a task that is blocked on the stream buffer to
+ * wait for data is moved out of the blocked state.  For example, if a task is
+ * blocked on a read of an empty stream buffer that has a trigger level of 1
+ * then the task will be unblocked when a single byte is written to the buffer
+ * or the task's block time expires.  As another example, if a task is blocked
+ * on a read of an empty stream buffer that has a trigger level of 10 then the
+ * task will not be unblocked until the stream buffer contains at least 10 bytes
+ * or the task's block time expires.  If a reading task's block time expires
+ * before the trigger level is reached then the task will still receive however
+ * many bytes are actually available.  Setting a trigger level of 0 will result
+ * in a trigger level of 1 being used.  It is not valid to specify a trigger
+ * level that is greater than the buffer size.
+ *
+ * A trigger level is set when the stream buffer is created, and can be modified
+ * using xStreamBufferSetTriggerLevel().
+ *
+ * @param xStreamBuffer The handle of the stream buffer being updated.
+ *
+ * @param xTriggerLevel The new trigger level for the stream buffer.
+ *
+ * @return If xTriggerLevel was less than or equal to the stream buffer's length
+ * then the trigger level will be updated and pdTRUE is returned.  Otherwise
+ * pdFALSE is returned.
+ *
+ * \defgroup xStreamBufferSetTriggerLevel xStreamBufferSetTriggerLevel
+ * \ingroup StreamBufferManagement
+ */
+BaseType_t xStreamBufferSetTriggerLevel( StreamBufferHandle_t xStreamBuffer, size_t xTriggerLevel ) PRIVILEGED_FUNCTION;
+
+/**
+ * stream_buffer.h
+ *
+
+BaseType_t xStreamBufferSendCompletedFromISR( StreamBufferHandle_t xStreamBuffer, BaseType_t *pxHigherPriorityTaskWoken );
+

+ *
+ * For advanced users only.
+ *
+ * The sbSEND_COMPLETED() macro is called from within the FreeRTOS APIs when
+ * data is sent to a message buffer or stream buffer.  If there was a task that
+ * was blocked on the message or stream buffer waiting for data to arrive then
+ * the sbSEND_COMPLETED() macro sends a notification to the task to remove it
+ * from the Blocked state.  xStreamBufferSendCompletedFromISR() does the same
+ * thing.  It is provided to enable application writers to implement their own
+ * version of sbSEND_COMPLETED(), and MUST NOT BE USED AT ANY OTHER TIME.
+ *
+ * See the example implemented in FreeRTOS/Demo/Minimal/MessageBufferAMP.c for
+ * additional information.
+ *
+ * @param xStreamBuffer The handle of the stream buffer to which data was
+ * written.
+ *
+ * @param pxHigherPriorityTaskWoken *pxHigherPriorityTaskWoken should be
+ * initialised to pdFALSE before it is passed into
+ * xStreamBufferSendCompletedFromISR().  If calling
+ * xStreamBufferSendCompletedFromISR() removes a task from the Blocked state,
+ * and the task has a priority above the priority of the currently running task,
+ * then *pxHigherPriorityTaskWoken will get set to pdTRUE indicating that a
+ * context switch should be performed before exiting the ISR.
+ *
+ * @return If a task was removed from the Blocked state then pdTRUE is returned.
+ * Otherwise pdFALSE is returned.
+ *
+ * \defgroup xStreamBufferSendCompletedFromISR xStreamBufferSendCompletedFromISR
+ * \ingroup StreamBufferManagement
+ */
+BaseType_t xStreamBufferSendCompletedFromISR( StreamBufferHandle_t xStreamBuffer, BaseType_t* pxHigherPriorityTaskWoken ) PRIVILEGED_FUNCTION;
+
+/**
+ * stream_buffer.h
+ *
+
+BaseType_t xStreamBufferReceiveCompletedFromISR( StreamBufferHandle_t xStreamBuffer, BaseType_t *pxHigherPriorityTaskWoken );
+

+ *
+ * For advanced users only.
+ *
+ * The sbRECEIVE_COMPLETED() macro is called from within the FreeRTOS APIs when
+ * data is read out of a message buffer or stream buffer.  If there was a task
+ * that was blocked on the message or stream buffer waiting for data to arrive
+ * then the sbRECEIVE_COMPLETED() macro sends a notification to the task to
+ * remove it from the Blocked state.  xStreamBufferReceiveCompletedFromISR()
+ * does the same thing.  It is provided to enable application writers to
+ * implement their own version of sbRECEIVE_COMPLETED(), and MUST NOT BE USED AT
+ * ANY OTHER TIME.
+ *
+ * See the example implemented in FreeRTOS/Demo/Minimal/MessageBufferAMP.c for
+ * additional information.
+ *
+ * @param xStreamBuffer The handle of the stream buffer from which data was
+ * read.
+ *
+ * @param pxHigherPriorityTaskWoken *pxHigherPriorityTaskWoken should be
+ * initialised to pdFALSE before it is passed into
+ * xStreamBufferReceiveCompletedFromISR().  If calling
+ * xStreamBufferReceiveCompletedFromISR() removes a task from the Blocked state,
+ * and the task has a priority above the priority of the currently running task,
+ * then *pxHigherPriorityTaskWoken will get set to pdTRUE indicating that a
+ * context switch should be performed before exiting the ISR.
+ *
+ * @return If a task was removed from the Blocked state then pdTRUE is returned.
+ * Otherwise pdFALSE is returned.
+ *
+ * \defgroup xStreamBufferReceiveCompletedFromISR xStreamBufferReceiveCompletedFromISR
+ * \ingroup StreamBufferManagement
+ */
+BaseType_t xStreamBufferReceiveCompletedFromISR( StreamBufferHandle_t xStreamBuffer, BaseType_t* pxHigherPriorityTaskWoken ) PRIVILEGED_FUNCTION;
+
+/* Functions below here are not part of the public API. */
+StreamBufferHandle_t xStreamBufferGenericCreate( size_t xBufferSizeBytes,
+        size_t xTriggerLevelBytes,
+        BaseType_t xIsMessageBuffer ) PRIVILEGED_FUNCTION;
+
+StreamBufferHandle_t xStreamBufferGenericCreateStatic( size_t xBufferSizeBytes,
+        size_t xTriggerLevelBytes,
+        BaseType_t xIsMessageBuffer,
+        uint8_t* const pucStreamBufferStorageArea,
+        StaticStreamBuffer_t* const pxStaticStreamBuffer ) PRIVILEGED_FUNCTION;
+
+#if( configUSE_TRACE_FACILITY == 1 )
+void vStreamBufferSetStreamBufferNumber( StreamBufferHandle_t xStreamBuffer, UBaseType_t uxStreamBufferNumber ) PRIVILEGED_FUNCTION;
+UBaseType_t uxStreamBufferGetStreamBufferNumber( StreamBufferHandle_t xStreamBuffer ) PRIVILEGED_FUNCTION;
+uint8_t ucStreamBufferGetStreamBufferType( StreamBufferHandle_t xStreamBuffer ) PRIVILEGED_FUNCTION;
+#endif
+
+#if defined( __cplusplus )
+}
+#endif
+
+#endif	/* !defined( STREAM_BUFFER_H ) */
diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/task.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/task.h
index dda920b0..9dcb18fc 100644
--- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/task.h
+++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/task.h
@@ -1,71 +1,29 @@
 /*
-    FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd.
-    All rights reserved
-
-    VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION.
-
-    This file is part of the FreeRTOS distribution.
-
-    FreeRTOS is free software; you can redistribute it and/or modify it under
-    the terms of the GNU General Public License (version 2) as published by the
-    Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception.
-
-    ***************************************************************************
-    >>!   NOTE: The modification to the GPL is included to allow you to     !<<
-    >>!   distribute a combined work that includes FreeRTOS without being   !<<
-    >>!   obliged to provide the source code for proprietary components     !<<
-    >>!   outside of the FreeRTOS kernel.                                   !<<
-    ***************************************************************************
-
-    FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY
-    WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
-    FOR A PARTICULAR PURPOSE.  Full license text is available on the following
-    link: http://www.freertos.org/a00114.html
-
-    ***************************************************************************
-     *                                                                       *
-     *    FreeRTOS provides completely free yet professionally developed,    *
-     *    robust, strictly quality controlled, supported, and cross          *
-     *    platform software that is more than just the market leader, it     *
-     *    is the industry's de facto standard.                               *
-     *                                                                       *
-     *    Help yourself get started quickly while simultaneously helping     *
-     *    to support the FreeRTOS project by purchasing a FreeRTOS           *
-     *    tutorial book, reference manual, or both:                          *
-     *    http://www.FreeRTOS.org/Documentation                              *
-     *                                                                       *
-    ***************************************************************************
-
-    http://www.FreeRTOS.org/FAQHelp.html - Having a problem?  Start by reading
-    the FAQ page "My application does not run, what could be wrong?".  Have you
-    defined configASSERT()?
-
-    http://www.FreeRTOS.org/support - In return for receiving this top quality
-    embedded software for free we request you assist our global community by
-    participating in the support forum.
-
-    http://www.FreeRTOS.org/training - Investing in training allows your team to
-    be as productive as possible as early as possible.  Now you can receive
-    FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers
-    Ltd, and the world's leading authority on the world's leading RTOS.
-
-    http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products,
-    including FreeRTOS+Trace - an indispensable productivity tool, a DOS
-    compatible FAT file system, and our tiny thread aware UDP/IP stack.
-
-    http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate.
-    Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS.
-
-    http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High
-    Integrity Systems ltd. to sell under the OpenRTOS brand.  Low cost OpenRTOS
-    licenses offer ticketed support, indemnification and commercial middleware.
-
-    http://www.SafeRTOS.com - High Integrity Systems also provide a safety
-    engineered and independently SIL3 certified version for use in safety and
-    mission critical applications that require provable dependability.
-
-    1 tab == 4 spaces!
-*/
+ * FreeRTOS Kernel V10.0.1
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
 
 
 #ifndef INC_TASK_H
@@ -85,10 +43,10 @@ extern "C" {
  * MACROS AND DEFINITIONS
  *----------------------------------------------------------*/
 
-#define tskKERNEL_VERSION_NUMBER "V8.2.3"
-#define tskKERNEL_VERSION_MAJOR 8
-#define tskKERNEL_VERSION_MINOR 2
-#define tskKERNEL_VERSION_BUILD 3
+#define tskKERNEL_VERSION_NUMBER "V10.0.1"
+#define tskKERNEL_VERSION_MAJOR 10
+#define tskKERNEL_VERSION_MINOR 0
+#define tskKERNEL_VERSION_BUILD 1
 
 /**
  * task. h
@@ -115,7 +73,8 @@ typedef enum
     eReady,			/* The task being queried is in a read or pending ready list. */
     eBlocked,		/* The task being queried is in the Blocked state. */
     eSuspended,		/* The task being queried is in the Suspended state, or is in the Blocked state with an infinite time out. */
-    eDeleted		/* The task being queried has been deleted, but its TCB has not yet been freed. */
+    eDeleted,		/* The task being queried has been deleted, but its TCB has not yet been freed. */
+    eInvalid			/* Used as an 'invalid state' value. */
 } eTaskState;
 
 /* Actions that can be performed when vTaskNotify() is called. */
@@ -159,6 +118,9 @@ typedef struct xTASK_PARAMETERS
     UBaseType_t uxPriority;
     StackType_t* puxStackBuffer;
     MemoryRegion_t xRegions[ portNUM_CONFIGURABLE_REGIONS ];
+#if ( ( portUSING_MPU_WRAPPERS == 1 ) && ( configSUPPORT_STATIC_ALLOCATION == 1 ) )
+    StaticTask_t* const pxTaskBuffer;
+#endif
 } TaskParameters_t;
 
 /* Used with the uxTaskGetSystemState() function to return the state of each task
@@ -172,6 +134,7 @@ typedef struct xTASK_STATUS
     UBaseType_t uxCurrentPriority;	/* The priority at which the task was running (may be inherited) when the structure was populated. */
     UBaseType_t uxBasePriority;		/* The priority to which the task will return if the task's current priority has been inherited to avoid unbounded priority inversion when obtaining a mutex.  Only valid if configUSE_MUTEXES is defined as 1 in FreeRTOSConfig.h. */
     uint32_t ulRunTimeCounter;		/* The total run time allocated to the task so far, as defined by the run time stats clock.  See http://www.freertos.org/rtos-run-time-stats.html.  Only valid when configGENERATE_RUN_TIME_STATS is defined as 1 in FreeRTOSConfig.h. */
+    StackType_t* pxStackBase;		/* Points to the lowest address of the task's stack area. */
     uint16_t usStackHighWaterMark;	/* The minimum amount of stack space that has remained for the task since the task was created.  The closer this value is to zero the closer the task has come to overflowing its stack. */
 } TaskStatus_t;
 
@@ -183,7 +146,6 @@ typedef enum
     eNoTasksWaitingTimeout	/* No tasks are waiting for a timeout so it is safe to enter a sleep mode that can only be exited by an external interrupt. */
 } eSleepModeStatus;
 
-
 /**
  * Defines the priority used by the idle task.  This must not be modified.
  *
@@ -268,7 +230,7 @@ is used in assert() statements. */
  BaseType_t xTaskCreate(
 							  TaskFunction_t pvTaskCode,
 							  const char * const pcName,
-							  uint16_t usStackDepth,
+							  configSTACK_DEPTH_TYPE usStackDepth,
 							  void *pvParameters,
 							  UBaseType_t uxPriority,
 							  TaskHandle_t *pvCreatedTask
@@ -276,6 +238,19 @@ is used in assert() statements. */
  *
  * Create a new task and add it to the list of tasks that are ready to run.
  *
+ * Internally, within the FreeRTOS implementation, tasks use two blocks of
+ * memory.  The first block is used to hold the task's data structures.  The
+ * second block is used by the task as its stack.  If a task is created using
+ * xTaskCreate() then both blocks of memory are automatically dynamically
+ * allocated inside the xTaskCreate() function.  (see
+ * http://www.freertos.org/a00111.html).  If a task is created using
+ * xTaskCreateStatic() then the application writer must provide the required
+ * memory.  xTaskCreateStatic() therefore allows a task to be created without
+ * using any dynamic memory allocation.
+ *
+ * See xTaskCreateStatic() for a version that does not use any dynamic memory
+ * allocation.
+ *
  * xTaskCreate() can only be used to create a task that has unrestricted
  * access to the entire microcontroller memory map.  Systems that include MPU
  * support can alternatively create an MPU constrained task using
@@ -342,13 +317,139 @@ is used in assert() statements. */
  * \defgroup xTaskCreate xTaskCreate
  * \ingroup Tasks
  */
-#define xTaskCreate( pvTaskCode, pcName, usStackDepth, pvParameters, uxPriority, pxCreatedTask ) xTaskGenericCreate( ( pvTaskCode ), ( pcName ), ( usStackDepth ), ( pvParameters ), ( uxPriority ), ( pxCreatedTask ), ( NULL ), ( NULL ) )
+#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 )
+BaseType_t xTaskCreate(	TaskFunction_t pxTaskCode,
+                        const char* const pcName,	/*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+                        const configSTACK_DEPTH_TYPE usStackDepth,
+                        void* const pvParameters,
+                        UBaseType_t uxPriority,
+                        TaskHandle_t* const pxCreatedTask ) PRIVILEGED_FUNCTION;
+#endif
+
+/**
+ * task. h
+ *
+ TaskHandle_t xTaskCreateStatic( TaskFunction_t pvTaskCode,
+								 const char * const pcName,
+								 uint32_t ulStackDepth,
+								 void *pvParameters,
+								 UBaseType_t uxPriority,
+								 StackType_t *pxStackBuffer,
+								 StaticTask_t *pxTaskBuffer );

+ *
+ * Create a new task and add it to the list of tasks that are ready to run.
+ *
+ * Internally, within the FreeRTOS implementation, tasks use two blocks of
+ * memory.  The first block is used to hold the task's data structures.  The
+ * second block is used by the task as its stack.  If a task is created using
+ * xTaskCreate() then both blocks of memory are automatically dynamically
+ * allocated inside the xTaskCreate() function.  (see
+ * http://www.freertos.org/a00111.html).  If a task is created using
+ * xTaskCreateStatic() then the application writer must provide the required
+ * memory.  xTaskCreateStatic() therefore allows a task to be created without
+ * using any dynamic memory allocation.
+ *
+ * @param pvTaskCode Pointer to the task entry function.  Tasks
+ * must be implemented to never return (i.e. continuous loop).
+ *
+ * @param pcName A descriptive name for the task.  This is mainly used to
+ * facilitate debugging.  The maximum length of the string is defined by
+ * configMAX_TASK_NAME_LEN in FreeRTOSConfig.h.
+ *
+ * @param ulStackDepth The size of the task stack specified as the number of
+ * variables the stack can hold - not the number of bytes.  For example, if
+ * the stack is 32-bits wide and ulStackDepth is defined as 100 then 400 bytes
+ * will be allocated for stack storage.
+ *
+ * @param pvParameters Pointer that will be used as the parameter for the task
+ * being created.
+ *
+ * @param uxPriority The priority at which the task will run.
+ *
+ * @param pxStackBuffer Must point to a StackType_t array that has at least
+ * ulStackDepth indexes - the array will then be used as the task's stack,
+ * removing the need for the stack to be allocated dynamically.
+ *
+ * @param pxTaskBuffer Must point to a variable of type StaticTask_t, which will
+ * then be used to hold the task's data structures, removing the need for the
+ * memory to be allocated dynamically.
+ *
+ * @return If neither pxStackBuffer or pxTaskBuffer are NULL, then the task will
+ * be created and pdPASS is returned.  If either pxStackBuffer or pxTaskBuffer
+ * are NULL then the task will not be created and
+ * errCOULD_NOT_ALLOCATE_REQUIRED_MEMORY is returned.
+ *
+ * Example usage:
+   
+
+    // Dimensions the buffer that the task being created will use as its stack.
+    // NOTE:  This is the number of words the stack will hold, not the number of
+    // bytes.  For example, if each stack item is 32-bits, and this is set to 100,
+    // then 400 bytes (100 * 32-bits) will be allocated.
+    #define STACK_SIZE 200
+
+    // Structure that will hold the TCB of the task being created.
+    StaticTask_t xTaskBuffer;
+
+    // Buffer that the task being created will use as its stack.  Note this is
+    // an array of StackType_t variables.  The size of StackType_t is dependent on
+    // the RTOS port.
+    StackType_t xStack[ STACK_SIZE ];
+
+    // Function that implements the task being created.
+    void vTaskCode( void * pvParameters )
+    {
+        // The parameter value is expected to be 1 as 1 is passed in the
+        // pvParameters value in the call to xTaskCreateStatic().
+        configASSERT( ( uint32_t ) pvParameters == 1UL );
+
+        for( ;; )
+        {
+            // Task code goes here.
+        }
+    }
+
+    // Function that creates a task.
+    void vOtherFunction( void )
+    {
+        TaskHandle_t xHandle = NULL;
+
+        // Create the task without using any dynamic memory allocation.
+        xHandle = xTaskCreateStatic(
+                      vTaskCode,       // Function that implements the task.
+                      "NAME",          // Text name for the task.
+                      STACK_SIZE,      // Stack size in words, not bytes.
+                      ( void * ) 1,    // Parameter passed into the task.
+                      tskIDLE_PRIORITY,// Priority at which the task is created.
+                      xStack,          // Array to use as the task's stack.
+                      &xTaskBuffer );  // Variable to hold the task's data structure.
+
+        // puxStackBuffer and pxTaskBuffer were not NULL, so the task will have
+        // been created, and xHandle will be the task's handle.  Use the handle
+        // to suspend the task.
+        vTaskSuspend( xHandle );
+    }
+   

+ * \defgroup xTaskCreateStatic xTaskCreateStatic
+ * \ingroup Tasks
+ */
+#if( configSUPPORT_STATIC_ALLOCATION == 1 )
+TaskHandle_t xTaskCreateStatic(	TaskFunction_t pxTaskCode,
+                                const char* const pcName,  /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+                                const uint32_t ulStackDepth,
+                                void* const pvParameters,
+                                UBaseType_t uxPriority,
+                                StackType_t* const puxStackBuffer,
+                                StaticTask_t* const pxTaskBuffer ) PRIVILEGED_FUNCTION;
+#endif /* configSUPPORT_STATIC_ALLOCATION */
 
 /**
  * task. h
  *
  BaseType_t xTaskCreateRestricted( TaskParameters_t *pxTaskDefinition, TaskHandle_t *pxCreatedTask );

  *
+ * Only available when configSUPPORT_DYNAMIC_ALLOCATION is set to 1.
+ *
  * xTaskCreateRestricted() should only be used in systems that include an MPU
  * implementation.
  *
@@ -356,6 +457,9 @@ is used in assert() statements. */
  * The function parameters define the memory regions and associated access
  * permissions allocated to the task.
  *
+ * See xTaskCreateRestrictedStatic() for a version that does not use any
+ * dynamic memory allocation.
+ *
  * @param pxTaskDefinition Pointer to a structure that contains a member
  * for each of the normal xTaskCreate() parameters (see the xTaskCreate() API
  * documentation) plus an optional stack buffer and the memory region
@@ -411,7 +515,97 @@ TaskHandle_t xHandle;
  * \defgroup xTaskCreateRestricted xTaskCreateRestricted
  * \ingroup Tasks
  */
-#define xTaskCreateRestricted( x, pxCreatedTask ) xTaskGenericCreate( ((x)->pvTaskCode), ((x)->pcName), ((x)->usStackDepth), ((x)->pvParameters), ((x)->uxPriority), (pxCreatedTask), ((x)->puxStackBuffer), ((x)->xRegions) )
+#if( portUSING_MPU_WRAPPERS == 1 )
+BaseType_t xTaskCreateRestricted( const TaskParameters_t* const pxTaskDefinition, TaskHandle_t* pxCreatedTask ) PRIVILEGED_FUNCTION;
+#endif
+
+/**
+ * task. h
+ *
+ BaseType_t xTaskCreateRestrictedStatic( TaskParameters_t *pxTaskDefinition, TaskHandle_t *pxCreatedTask );

+ *
+ * Only available when configSUPPORT_STATIC_ALLOCATION is set to 1.
+ *
+ * xTaskCreateRestrictedStatic() should only be used in systems that include an
+ * MPU implementation.
+ *
+ * Internally, within the FreeRTOS implementation, tasks use two blocks of
+ * memory.  The first block is used to hold the task's data structures.  The
+ * second block is used by the task as its stack.  If a task is created using
+ * xTaskCreateRestricted() then the stack is provided by the application writer,
+ * and the memory used to hold the task's data structure is automatically
+ * dynamically allocated inside the xTaskCreateRestricted() function.  If a task
+ * is created using xTaskCreateRestrictedStatic() then the application writer
+ * must provide the memory used to hold the task's data structures too.
+ * xTaskCreateRestrictedStatic() therefore allows a memory protected task to be
+ * created without using any dynamic memory allocation.
+ *
+ * @param pxTaskDefinition Pointer to a structure that contains a member
+ * for each of the normal xTaskCreate() parameters (see the xTaskCreate() API
+ * documentation) plus an optional stack buffer and the memory region
+ * definitions.  If configSUPPORT_STATIC_ALLOCATION is set to 1 the structure
+ * contains an additional member, which is used to point to a variable of type
+ * StaticTask_t - which is then used to hold the task's data structure.
+ *
+ * @param pxCreatedTask Used to pass back a handle by which the created task
+ * can be referenced.
+ *
+ * @return pdPASS if the task was successfully created and added to a ready
+ * list, otherwise an error code defined in the file projdefs.h
+ *
+ * Example usage:
+   
+// Create an TaskParameters_t structure that defines the task to be created.
+// The StaticTask_t variable is only included in the structure when
+// configSUPPORT_STATIC_ALLOCATION is set to 1.  The PRIVILEGED_DATA macro can
+// be used to force the variable into the RTOS kernel's privileged data area.
+static PRIVILEGED_DATA StaticTask_t xTaskBuffer;
+static const TaskParameters_t xCheckTaskParameters =
+{
+	vATask,		// pvTaskCode - the function that implements the task.
+	"ATask",	// pcName - just a text name for the task to assist debugging.
+	100,		// usStackDepth	- the stack size DEFINED IN WORDS.
+	NULL,		// pvParameters - passed into the task function as the function parameters.
+	( 1UL | portPRIVILEGE_BIT ),// uxPriority - task priority, set the portPRIVILEGE_BIT if the task should run in a privileged state.
+	cStackBuffer,// puxStackBuffer - the buffer to be used as the task stack.
+
+	// xRegions - Allocate up to three separate memory regions for access by
+	// the task, with appropriate access permissions.  Different processors have
+	// different memory alignment requirements - refer to the FreeRTOS documentation
+	// for full information.
+	{
+		// Base address					Length	Parameters
+        { cReadWriteArray,				32,		portMPU_REGION_READ_WRITE },
+        { cReadOnlyArray,				32,		portMPU_REGION_READ_ONLY },
+        { cPrivilegedOnlyAccessArray,	128,	portMPU_REGION_PRIVILEGED_READ_WRITE }
+	}
+
+	&xTaskBuffer; // Holds the task's data structure.
+};
+
+int main( void )
+{
+TaskHandle_t xHandle;
+
+	// Create a task from the const structure defined above.  The task handle
+	// is requested (the second parameter is not NULL) but in this case just for
+	// demonstration purposes as its not actually used.
+	xTaskCreateRestricted( &xRegTest1Parameters, &xHandle );
+
+	// Start the scheduler.
+	vTaskStartScheduler();
+
+	// Will only get here if there was insufficient memory to create the idle
+	// and/or timer task.
+	for( ;; );
+}
+   

+ * \defgroup xTaskCreateRestrictedStatic xTaskCreateRestrictedStatic
+ * \ingroup Tasks
+ */
+#if( ( portUSING_MPU_WRAPPERS == 1 ) && ( configSUPPORT_STATIC_ALLOCATION == 1 ) )
+BaseType_t xTaskCreateRestrictedStatic( const TaskParameters_t* const pxTaskDefinition, TaskHandle_t* pxCreatedTask ) PRIVILEGED_FUNCTION;
+#endif
 
 /**
  * task. h
@@ -613,6 +807,31 @@ void vTaskDelay( const TickType_t xTicksToDelay ) PRIVILEGED_FUNCTION;
  */
 void vTaskDelayUntil( TickType_t* const pxPreviousWakeTime, const TickType_t xTimeIncrement ) PRIVILEGED_FUNCTION;
 
+/**
+ * task. h
+ * 
BaseType_t xTaskAbortDelay( TaskHandle_t xTask );

+ *
+ * INCLUDE_xTaskAbortDelay must be defined as 1 in FreeRTOSConfig.h for this
+ * function to be available.
+ *
+ * A task will enter the Blocked state when it is waiting for an event.  The
+ * event it is waiting for can be a temporal event (waiting for a time), such
+ * as when vTaskDelay() is called, or an event on an object, such as when
+ * xQueueReceive() or ulTaskNotifyTake() is called.  If the handle of a task
+ * that is in the Blocked state is used in a call to xTaskAbortDelay() then the
+ * task will leave the Blocked state, and return from whichever function call
+ * placed the task into the Blocked state.
+ *
+ * @param xTask The handle of the task to remove from the Blocked state.
+ *
+ * @return If the task referenced by xTask was not in the Blocked state then
+ * pdFAIL is returned.  Otherwise pdPASS is returned.
+ *
+ * \defgroup xTaskAbortDelay xTaskAbortDelay
+ * \ingroup TaskCtrl
+ */
+BaseType_t xTaskAbortDelay( TaskHandle_t xTask ) PRIVILEGED_FUNCTION;
+
 /**
  * task. h
  * 
UBaseType_t uxTaskPriorityGet( TaskHandle_t xTask );

@@ -686,6 +905,62 @@ UBaseType_t uxTaskPriorityGetFromISR( TaskHandle_t xTask ) PRIVILEGED_FUNCTION;
  */
 eTaskState eTaskGetState( TaskHandle_t xTask ) PRIVILEGED_FUNCTION;
 
+/**
+ * task. h
+ * 
void vTaskGetInfo( TaskHandle_t xTask, TaskStatus_t *pxTaskStatus, BaseType_t xGetFreeStackSpace, eTaskState eState );

+ *
+ * configUSE_TRACE_FACILITY must be defined as 1 for this function to be
+ * available.  See the configuration section for more information.
+ *
+ * Populates a TaskStatus_t structure with information about a task.
+ *
+ * @param xTask Handle of the task being queried.  If xTask is NULL then
+ * information will be returned about the calling task.
+ *
+ * @param pxTaskStatus A pointer to the TaskStatus_t structure that will be
+ * filled with information about the task referenced by the handle passed using
+ * the xTask parameter.
+ *
+ * @xGetFreeStackSpace The TaskStatus_t structure contains a member to report
+ * the stack high water mark of the task being queried.  Calculating the stack
+ * high water mark takes a relatively long time, and can make the system
+ * temporarily unresponsive - so the xGetFreeStackSpace parameter is provided to
+ * allow the high water mark checking to be skipped.  The high watermark value
+ * will only be written to the TaskStatus_t structure if xGetFreeStackSpace is
+ * not set to pdFALSE;
+ *
+ * @param eState The TaskStatus_t structure contains a member to report the
+ * state of the task being queried.  Obtaining the task state is not as fast as
+ * a simple assignment - so the eState parameter is provided to allow the state
+ * information to be omitted from the TaskStatus_t structure.  To obtain state
+ * information then set eState to eInvalid - otherwise the value passed in
+ * eState will be reported as the task state in the TaskStatus_t structure.
+ *
+ * Example usage:
+   
+ void vAFunction( void )
+ {
+ TaskHandle_t xHandle;
+ TaskStatus_t xTaskDetails;
+
+    // Obtain the handle of a task from its name.
+    xHandle = xTaskGetHandle( "Task_Name" );
+
+    // Check the handle is not NULL.
+    configASSERT( xHandle );
+
+    // Use the handle to obtain further information about the task.
+    vTaskGetInfo( xHandle,
+                  &xTaskDetails,
+                  pdTRUE, // Include the high water mark in xTaskDetails.
+                  eInvalid ); // Include the task state in xTaskDetails.
+ }
+   

+ * \defgroup vTaskGetInfo vTaskGetInfo
+ * \ingroup TaskCtrl
+ */
+void vTaskGetInfo( TaskHandle_t xTask, TaskStatus_t* pxTaskStatus, BaseType_t xGetFreeStackSpace, eTaskState eState ) PRIVILEGED_FUNCTION;
+
 /**
  * task. h
  * 
void vTaskPrioritySet( TaskHandle_t xTask, UBaseType_t uxNewPriority );

@@ -1098,17 +1373,32 @@ UBaseType_t uxTaskGetNumberOfTasks( void ) PRIVILEGED_FUNCTION;
 
 /**
  * task. h
- * 
char *pcTaskGetTaskName( TaskHandle_t xTaskToQuery );

+ * 
char *pcTaskGetName( TaskHandle_t xTaskToQuery );

  *
  * @return The text (human readable) name of the task referenced by the handle
  * xTaskToQuery.  A task can query its own name by either passing in its own
- * handle, or by setting xTaskToQuery to NULL.  INCLUDE_pcTaskGetTaskName must be
- * set to 1 in FreeRTOSConfig.h for pcTaskGetTaskName() to be available.
+ * handle, or by setting xTaskToQuery to NULL.
  *
- * \defgroup pcTaskGetTaskName pcTaskGetTaskName
+ * \defgroup pcTaskGetName pcTaskGetName
  * \ingroup TaskUtils
  */
-char* pcTaskGetTaskName( TaskHandle_t xTaskToQuery ) PRIVILEGED_FUNCTION; /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+char* pcTaskGetName( TaskHandle_t xTaskToQuery ) PRIVILEGED_FUNCTION; /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+
+/**
+ * task. h
+ * 
TaskHandle_t xTaskGetHandle( const char *pcNameToQuery );

+ *
+ * NOTE:  This function takes a relatively long time to complete and should be
+ * used sparingly.
+ *
+ * @return The handle of the task that has the human readable name pcNameToQuery.
+ * NULL is returned if no matching name is found.  INCLUDE_xTaskGetHandle
+ * must be set to 1 in FreeRTOSConfig.h for pcTaskGetHandle() to be available.
+ *
+ * \defgroup pcTaskGetHandle pcTaskGetHandle
+ * \ingroup TaskUtils
+ */
+TaskHandle_t xTaskGetHandle( const char* pcNameToQuery ) PRIVILEGED_FUNCTION; /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
 
 /**
  * task.h
@@ -1894,7 +2184,7 @@ void vTaskPlaceOnUnorderedEventList( List_t* pxEventList, const TickType_t xItem
  * indefinitely, whereas vTaskPlaceOnEventList() does.
  *
  */
-void vTaskPlaceOnEventListRestricted( List_t* const pxEventList, const TickType_t xTicksToWait, const BaseType_t xWaitIndefinitely ) PRIVILEGED_FUNCTION;
+void vTaskPlaceOnEventListRestricted( List_t* const pxEventList, TickType_t xTicksToWait, const BaseType_t xWaitIndefinitely ) PRIVILEGED_FUNCTION;
 
 /*
  * THIS FUNCTION MUST NOT BE USED FROM APPLICATION CODE.  IT IS AN
@@ -1905,14 +2195,14 @@ void vTaskPlaceOnEventListRestricted( List_t* const pxEventList, const TickType_
  * Removes a task from both the specified event list and the list of blocked
  * tasks, and places it on a ready queue.
  *
- * xTaskRemoveFromEventList()/xTaskRemoveFromUnorderedEventList() will be called
+ * xTaskRemoveFromEventList()/vTaskRemoveFromUnorderedEventList() will be called
  * if either an event occurs to unblock a task, or the block timeout period
  * expires.
  *
  * xTaskRemoveFromEventList() is used when the event list is in task priority
  * order.  It removes the list item from the head of the event list as that will
  * have the highest priority owning task of all the tasks on the event list.
- * xTaskRemoveFromUnorderedEventList() is used when the event list is not
+ * vTaskRemoveFromUnorderedEventList() is used when the event list is not
  * ordered and the event list items hold something other than the owning tasks
  * priority.  In this case the event list item value is updated to the value
  * passed in the xItemValue parameter.
@@ -1921,7 +2211,7 @@ void vTaskPlaceOnEventListRestricted( List_t* const pxEventList, const TickType_
  * making the call, otherwise pdFALSE.
  */
 BaseType_t xTaskRemoveFromEventList( const List_t* const pxEventList ) PRIVILEGED_FUNCTION;
-BaseType_t xTaskRemoveFromUnorderedEventList( ListItem_t* pxEventListItem, const TickType_t xItemValue ) PRIVILEGED_FUNCTION;
+void vTaskRemoveFromUnorderedEventList( ListItem_t* pxEventListItem, const TickType_t xItemValue ) PRIVILEGED_FUNCTION;
 
 /*
  * THIS FUNCTION MUST NOT BE USED FROM APPLICATION CODE.  IT IS ONLY
@@ -1971,7 +2261,7 @@ BaseType_t xTaskGetSchedulerState( void ) PRIVILEGED_FUNCTION;
  * Raises the priority of the mutex holder to that of the calling task should
  * the mutex holder have a priority less than the calling task.
  */
-void vTaskPriorityInherit( TaskHandle_t const pxMutexHolder ) PRIVILEGED_FUNCTION;
+BaseType_t xTaskPriorityInherit( TaskHandle_t const pxMutexHolder ) PRIVILEGED_FUNCTION;
 
 /*
  * Set the priority of a task back to its proper priority in the case that it
@@ -1980,10 +2270,14 @@ void vTaskPriorityInherit( TaskHandle_t const pxMutexHolder ) PRIVILEGED_FUNCTIO
 BaseType_t xTaskPriorityDisinherit( TaskHandle_t const pxMutexHolder ) PRIVILEGED_FUNCTION;
 
 /*
- * Generic version of the task creation function which is in turn called by the
- * xTaskCreate() and xTaskCreateRestricted() macros.
+ * If a higher priority task attempting to obtain a mutex caused a lower
+ * priority task to inherit the higher priority task's priority - but the higher
+ * priority task then timed out without obtaining the mutex, then the lower
+ * priority task will disinherit the priority again - but only down as far as
+ * the highest priority task that is still waiting for the mutex (if there were
+ * more than one task waiting for the mutex).
  */
-BaseType_t xTaskGenericCreate( TaskFunction_t pxTaskCode, const char* const pcName, const uint16_t usStackDepth, void* const pvParameters, UBaseType_t uxPriority, TaskHandle_t* const pxCreatedTask, StackType_t* const puxStackBuffer, const MemoryRegion_t* const xRegions ) PRIVILEGED_FUNCTION;      /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+void vTaskPriorityDisinheritAfterTimeout( TaskHandle_t const pxMutexHolder, UBaseType_t uxHighestPriorityWaitingTask ) PRIVILEGED_FUNCTION;
 
 /*
  * Get the uxTCBNumber assigned to the task referenced by the xTask parameter.
@@ -2028,6 +2322,13 @@ eSleepModeStatus eTaskConfirmSleepModeStatus( void ) PRIVILEGED_FUNCTION;
  */
 void* pvTaskIncrementMutexHeldCount( void ) PRIVILEGED_FUNCTION;
 
+/*
+ * For internal use only.  Same as vTaskSetTimeOutState(), but without a critial
+ * section.
+ */
+void vTaskInternalSetTimeOutState( TimeOut_t* const pxTimeOut ) PRIVILEGED_FUNCTION;
+
+
 #ifdef __cplusplus
 }
 #endif
diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/timers.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/timers.h
index 346184e0..e1ce122c 100644
--- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/timers.h
+++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/include/timers.h
@@ -1,71 +1,29 @@
 /*
-    FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd.
-    All rights reserved
-
-    VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION.
-
-    This file is part of the FreeRTOS distribution.
-
-    FreeRTOS is free software; you can redistribute it and/or modify it under
-    the terms of the GNU General Public License (version 2) as published by the
-    Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception.
-
-    ***************************************************************************
-    >>!   NOTE: The modification to the GPL is included to allow you to     !<<
-    >>!   distribute a combined work that includes FreeRTOS without being   !<<
-    >>!   obliged to provide the source code for proprietary components     !<<
-    >>!   outside of the FreeRTOS kernel.                                   !<<
-    ***************************************************************************
-
-    FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY
-    WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
-    FOR A PARTICULAR PURPOSE.  Full license text is available on the following
-    link: http://www.freertos.org/a00114.html
-
-    ***************************************************************************
-     *                                                                       *
-     *    FreeRTOS provides completely free yet professionally developed,    *
-     *    robust, strictly quality controlled, supported, and cross          *
-     *    platform software that is more than just the market leader, it     *
-     *    is the industry's de facto standard.                               *
-     *                                                                       *
-     *    Help yourself get started quickly while simultaneously helping     *
-     *    to support the FreeRTOS project by purchasing a FreeRTOS           *
-     *    tutorial book, reference manual, or both:                          *
-     *    http://www.FreeRTOS.org/Documentation                              *
-     *                                                                       *
-    ***************************************************************************
-
-    http://www.FreeRTOS.org/FAQHelp.html - Having a problem?  Start by reading
-    the FAQ page "My application does not run, what could be wrong?".  Have you
-    defined configASSERT()?
-
-    http://www.FreeRTOS.org/support - In return for receiving this top quality
-    embedded software for free we request you assist our global community by
-    participating in the support forum.
-
-    http://www.FreeRTOS.org/training - Investing in training allows your team to
-    be as productive as possible as early as possible.  Now you can receive
-    FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers
-    Ltd, and the world's leading authority on the world's leading RTOS.
-
-    http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products,
-    including FreeRTOS+Trace - an indispensable productivity tool, a DOS
-    compatible FAT file system, and our tiny thread aware UDP/IP stack.
-
-    http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate.
-    Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS.
-
-    http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High
-    Integrity Systems ltd. to sell under the OpenRTOS brand.  Low cost OpenRTOS
-    licenses offer ticketed support, indemnification and commercial middleware.
-
-    http://www.SafeRTOS.com - High Integrity Systems also provide a safety
-    engineered and independently SIL3 certified version for use in safety and
-    mission critical applications that require provable dependability.
-
-    1 tab == 4 spaces!
-*/
+ * FreeRTOS Kernel V10.0.1
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
 
 
 #ifndef TIMERS_H
@@ -75,10 +33,10 @@
 #error "include FreeRTOS.h must appear in source files before include timers.h"
 #endif
 
-/*lint -e537 This headers are only multiply included if the application code
+/*lint -save -e537 This headers are only multiply included if the application code
 happens to also be including task.h. */
 #include "task.h"
-/*lint +e537 */
+/*lint -restore */
 
 #ifdef __cplusplus
 extern "C" {
@@ -135,9 +93,17 @@ typedef void (*PendedFunction_t)( void*, uint32_t );
  * 								void * pvTimerID,
  * 								TimerCallbackFunction_t pxCallbackFunction );
  *
- * Creates a new software timer instance.  This allocates the storage required
- * by the new timer, initialises the new timers internal state, and returns a
- * handle by which the new timer can be referenced.
+ * Creates a new software timer instance, and returns a handle by which the
+ * created software timer can be referenced.
+ *
+ * Internally, within the FreeRTOS implementation, software timers use a block
+ * of memory, in which the timer data structure is stored.  If a software timer
+ * is created using xTimerCreate() then the required memory is automatically
+ * dynamically allocated inside the xTimerCreate() function.  (see
+ * http://www.freertos.org/a00111.html).  If a software timer is created using
+ * xTimerCreateStatic() then the application writer must provide the memory that
+ * will get used by the software timer.  xTimerCreateStatic() therefore allows a
+ * software timer to be created without using any dynamic memory allocation.
  *
  * Timers are created in the dormant state.  The xTimerStart(), xTimerReset(),
  * xTimerStartFromISR(), xTimerResetFromISR(), xTimerChangePeriod() and
@@ -250,14 +216,151 @@ typedef void (*PendedFunction_t)( void*, uint32_t );
  *
  *     // Starting the scheduler will start the timers running as they have already
  *     // been set into the active state.
- *     xTaskStartScheduler();
+ *     vTaskStartScheduler();
  *
  *     // Should not reach here.
  *     for( ;; );
  * }
  * @endverbatim
  */
-TimerHandle_t xTimerCreate( const char* const pcTimerName, const TickType_t xTimerPeriodInTicks, const UBaseType_t uxAutoReload, void* const pvTimerID, TimerCallbackFunction_t pxCallbackFunction ) PRIVILEGED_FUNCTION;   /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 )
+TimerHandle_t xTimerCreate(	const char* const pcTimerName,			/*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+                            const TickType_t xTimerPeriodInTicks,
+                            const UBaseType_t uxAutoReload,
+                            void* const pvTimerID,
+                            TimerCallbackFunction_t pxCallbackFunction ) PRIVILEGED_FUNCTION;
+#endif
+
+/**
+ * TimerHandle_t xTimerCreateStatic(const char * const pcTimerName,
+ * 									TickType_t xTimerPeriodInTicks,
+ * 									UBaseType_t uxAutoReload,
+ * 									void * pvTimerID,
+ * 									TimerCallbackFunction_t pxCallbackFunction,
+ *									StaticTimer_t *pxTimerBuffer );
+ *
+ * Creates a new software timer instance, and returns a handle by which the
+ * created software timer can be referenced.
+ *
+ * Internally, within the FreeRTOS implementation, software timers use a block
+ * of memory, in which the timer data structure is stored.  If a software timer
+ * is created using xTimerCreate() then the required memory is automatically
+ * dynamically allocated inside the xTimerCreate() function.  (see
+ * http://www.freertos.org/a00111.html).  If a software timer is created using
+ * xTimerCreateStatic() then the application writer must provide the memory that
+ * will get used by the software timer.  xTimerCreateStatic() therefore allows a
+ * software timer to be created without using any dynamic memory allocation.
+ *
+ * Timers are created in the dormant state.  The xTimerStart(), xTimerReset(),
+ * xTimerStartFromISR(), xTimerResetFromISR(), xTimerChangePeriod() and
+ * xTimerChangePeriodFromISR() API functions can all be used to transition a
+ * timer into the active state.
+ *
+ * @param pcTimerName A text name that is assigned to the timer.  This is done
+ * purely to assist debugging.  The kernel itself only ever references a timer
+ * by its handle, and never by its name.
+ *
+ * @param xTimerPeriodInTicks The timer period.  The time is defined in tick
+ * periods so the constant portTICK_PERIOD_MS can be used to convert a time that
+ * has been specified in milliseconds.  For example, if the timer must expire
+ * after 100 ticks, then xTimerPeriodInTicks should be set to 100.
+ * Alternatively, if the timer must expire after 500ms, then xPeriod can be set
+ * to ( 500 / portTICK_PERIOD_MS ) provided configTICK_RATE_HZ is less than or
+ * equal to 1000.
+ *
+ * @param uxAutoReload If uxAutoReload is set to pdTRUE then the timer will
+ * expire repeatedly with a frequency set by the xTimerPeriodInTicks parameter.
+ * If uxAutoReload is set to pdFALSE then the timer will be a one-shot timer and
+ * enter the dormant state after it expires.
+ *
+ * @param pvTimerID An identifier that is assigned to the timer being created.
+ * Typically this would be used in the timer callback function to identify which
+ * timer expired when the same callback function is assigned to more than one
+ * timer.
+ *
+ * @param pxCallbackFunction The function to call when the timer expires.
+ * Callback functions must have the prototype defined by TimerCallbackFunction_t,
+ * which is "void vCallbackFunction( TimerHandle_t xTimer );".
+ *
+ * @param pxTimerBuffer Must point to a variable of type StaticTimer_t, which
+ * will be then be used to hold the software timer's data structures, removing
+ * the need for the memory to be allocated dynamically.
+ *
+ * @return If the timer is created then a handle to the created timer is
+ * returned.  If pxTimerBuffer was NULL then NULL is returned.
+ *
+ * Example usage:
+ * @verbatim
+ *
+ * // The buffer used to hold the software timer's data structure.
+ * static StaticTimer_t xTimerBuffer;
+ *
+ * // A variable that will be incremented by the software timer's callback
+ * // function.
+ * UBaseType_t uxVariableToIncrement = 0;
+ *
+ * // A software timer callback function that increments a variable passed to
+ * // it when the software timer was created.  After the 5th increment the
+ * // callback function stops the software timer.
+ * static void prvTimerCallback( TimerHandle_t xExpiredTimer )
+ * {
+ * UBaseType_t *puxVariableToIncrement;
+ * BaseType_t xReturned;
+ *
+ *     // Obtain the address of the variable to increment from the timer ID.
+ *     puxVariableToIncrement = ( UBaseType_t * ) pvTimerGetTimerID( xExpiredTimer );
+ *
+ *     // Increment the variable to show the timer callback has executed.
+ *     ( *puxVariableToIncrement )++;
+ *
+ *     // If this callback has executed the required number of times, stop the
+ *     // timer.
+ *     if( *puxVariableToIncrement == 5 )
+ *     {
+ *         // This is called from a timer callback so must not block.
+ *         xTimerStop( xExpiredTimer, staticDONT_BLOCK );
+ *     }
+ * }
+ *
+ *
+ * void main( void )
+ * {
+ *     // Create the software time.  xTimerCreateStatic() has an extra parameter
+ *     // than the normal xTimerCreate() API function.  The parameter is a pointer
+ *     // to the StaticTimer_t structure that will hold the software timer
+ *     // structure.  If the parameter is passed as NULL then the structure will be
+ *     // allocated dynamically, just as if xTimerCreate() had been called.
+ *     xTimer = xTimerCreateStatic( "T1",             // Text name for the task.  Helps debugging only.  Not used by FreeRTOS.
+ *                                  xTimerPeriod,     // The period of the timer in ticks.
+ *                                  pdTRUE,           // This is an auto-reload timer.
+ *                                  ( void * ) &uxVariableToIncrement,    // A variable incremented by the software timer's callback function
+ *                                  prvTimerCallback, // The function to execute when the timer expires.
+ *                                  &xTimerBuffer );  // The buffer that will hold the software timer structure.
+ *
+ *     // The scheduler has not started yet so a block time is not used.
+ *     xReturned = xTimerStart( xTimer, 0 );
+ *
+ *     // ...
+ *     // Create tasks here.
+ *     // ...
+ *
+ *     // Starting the scheduler will start the timers running as they have already
+ *     // been set into the active state.
+ *     vTaskStartScheduler();
+ *
+ *     // Should not reach here.
+ *     for( ;; );
+ * }
+ * @endverbatim
+ */
+#if( configSUPPORT_STATIC_ALLOCATION == 1 )
+TimerHandle_t xTimerCreateStatic(	const char* const pcTimerName,			/*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+                                    const TickType_t xTimerPeriodInTicks,
+                                    const UBaseType_t uxAutoReload,
+                                    void* const pvTimerID,
+                                    TimerCallbackFunction_t pxCallbackFunction,
+                                    StaticTimer_t* pxTimerBuffer ) PRIVILEGED_FUNCTION;
+#endif /* configSUPPORT_STATIC_ALLOCATION */
 
 /**
  * void *pvTimerGetTimerID( TimerHandle_t xTimer );
@@ -342,9 +445,6 @@ BaseType_t xTimerIsTimerActive( TimerHandle_t xTimer ) PRIVILEGED_FUNCTION;
 /**
  * TaskHandle_t xTimerGetTimerDaemonTaskHandle( void );
  *
- * xTimerGetTimerDaemonTaskHandle() is only available if
- * INCLUDE_xTimerGetTimerDaemonTaskHandle is set to 1 in FreeRTOSConfig.h.
- *
  * Simply returns the handle of the timer service/daemon task.  It it not valid
  * to call xTimerGetTimerDaemonTaskHandle() before the scheduler has been started.
  */
@@ -677,7 +777,7 @@ TaskHandle_t xTimerGetTimerDaemonTaskHandle( void ) PRIVILEGED_FUNCTION;
  *
  *     // Starting the scheduler will start the timer running as it has already
  *     // been set into the active state.
- *     xTaskStartScheduler();
+ *     vTaskStartScheduler();
  *
  *     // Should not reach here.
  *     for( ;; );
@@ -1120,7 +1220,7 @@ BaseType_t xTimerPendFunctionCallFromISR( PendedFunction_t xFunctionToPend, void
 BaseType_t xTimerPendFunctionCall( PendedFunction_t xFunctionToPend, void* pvParameter1, uint32_t ulParameter2, TickType_t xTicksToWait ) PRIVILEGED_FUNCTION;
 
 /**
- * const char * const pcTimerGetTimerName( TimerHandle_t xTimer );
+ * const char * const pcTimerGetName( TimerHandle_t xTimer );
  *
  * Returns the name that was assigned to a timer when the timer was created.
  *
@@ -1128,7 +1228,33 @@ BaseType_t xTimerPendFunctionCall( PendedFunction_t xFunctionToPend, void* pvPar
  *
  * @return The name assigned to the timer specified by the xTimer parameter.
  */
-const char* pcTimerGetTimerName( TimerHandle_t xTimer ) PRIVILEGED_FUNCTION;  /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+const char* pcTimerGetName( TimerHandle_t xTimer ) PRIVILEGED_FUNCTION;  /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+
+/**
+ * TickType_t xTimerGetPeriod( TimerHandle_t xTimer );
+ *
+ * Returns the period of a timer.
+ *
+ * @param xTimer The handle of the timer being queried.
+ *
+ * @return The period of the timer in ticks.
+ */
+TickType_t xTimerGetPeriod( TimerHandle_t xTimer ) PRIVILEGED_FUNCTION;
+
+/**
+* TickType_t xTimerGetExpiryTime( TimerHandle_t xTimer );
+*
+* Returns the time in ticks at which the timer will expire.  If this is less
+* than the current tick count then the expiry time has overflowed from the
+* current time.
+*
+* @param xTimer The handle of the timer being queried.
+*
+* @return If the timer is running then the time in ticks at which the timer
+* will next expire is returned.  If the timer is not running then the return
+* value is undefined.
+*/
+TickType_t xTimerGetExpiryTime( TimerHandle_t xTimer ) PRIVILEGED_FUNCTION;
 
 /*
  * Functions beyond this part are not part of the public API and are intended
@@ -1137,6 +1263,11 @@ const char* pcTimerGetTimerName( TimerHandle_t xTimer ) PRIVILEGED_FUNCTION;  /*
 BaseType_t xTimerCreateTimerTask( void ) PRIVILEGED_FUNCTION;
 BaseType_t xTimerGenericCommand( TimerHandle_t xTimer, const BaseType_t xCommandID, const TickType_t xOptionalValue, BaseType_t* const pxHigherPriorityTaskWoken, const TickType_t xTicksToWait ) PRIVILEGED_FUNCTION;
 
+#if( configUSE_TRACE_FACILITY == 1 )
+void vTimerSetTimerNumber( TimerHandle_t xTimer, UBaseType_t uxTimerNumber ) PRIVILEGED_FUNCTION;
+UBaseType_t uxTimerGetTimerNumber( TimerHandle_t xTimer ) PRIVILEGED_FUNCTION;
+#endif
+
 #ifdef __cplusplus
 }
 #endif
diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/list.c b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/list.c
index 41ca60a3..0dc0e8c1 100644
--- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/list.c
+++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/list.c
@@ -1,71 +1,29 @@
 /*
-    FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd.
-    All rights reserved
-
-    VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION.
-
-    This file is part of the FreeRTOS distribution.
-
-    FreeRTOS is free software; you can redistribute it and/or modify it under
-    the terms of the GNU General Public License (version 2) as published by the
-    Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception.
-
-    ***************************************************************************
-    >>!   NOTE: The modification to the GPL is included to allow you to     !<<
-    >>!   distribute a combined work that includes FreeRTOS without being   !<<
-    >>!   obliged to provide the source code for proprietary components     !<<
-    >>!   outside of the FreeRTOS kernel.                                   !<<
-    ***************************************************************************
-
-    FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY
-    WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
-    FOR A PARTICULAR PURPOSE.  Full license text is available on the following
-    link: http://www.freertos.org/a00114.html
-
-    ***************************************************************************
-     *                                                                       *
-     *    FreeRTOS provides completely free yet professionally developed,    *
-     *    robust, strictly quality controlled, supported, and cross          *
-     *    platform software that is more than just the market leader, it     *
-     *    is the industry's de facto standard.                               *
-     *                                                                       *
-     *    Help yourself get started quickly while simultaneously helping     *
-     *    to support the FreeRTOS project by purchasing a FreeRTOS           *
-     *    tutorial book, reference manual, or both:                          *
-     *    http://www.FreeRTOS.org/Documentation                              *
-     *                                                                       *
-    ***************************************************************************
-
-    http://www.FreeRTOS.org/FAQHelp.html - Having a problem?  Start by reading
-    the FAQ page "My application does not run, what could be wrong?".  Have you
-    defined configASSERT()?
-
-    http://www.FreeRTOS.org/support - In return for receiving this top quality
-    embedded software for free we request you assist our global community by
-    participating in the support forum.
-
-    http://www.FreeRTOS.org/training - Investing in training allows your team to
-    be as productive as possible as early as possible.  Now you can receive
-    FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers
-    Ltd, and the world's leading authority on the world's leading RTOS.
-
-    http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products,
-    including FreeRTOS+Trace - an indispensable productivity tool, a DOS
-    compatible FAT file system, and our tiny thread aware UDP/IP stack.
-
-    http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate.
-    Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS.
-
-    http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High
-    Integrity Systems ltd. to sell under the OpenRTOS brand.  Low cost OpenRTOS
-    licenses offer ticketed support, indemnification and commercial middleware.
-
-    http://www.SafeRTOS.com - High Integrity Systems also provide a safety
-    engineered and independently SIL3 certified version for use in safety and
-    mission critical applications that require provable dependability.
-
-    1 tab == 4 spaces!
-*/
+ * FreeRTOS Kernel V10.0.1
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
 
 
 #include 
@@ -82,14 +40,18 @@ void vListInitialise( List_t* const pxList )
     end of the list.  To initialise the list the list end is inserted
     as the only list entry. */
     pxList->pxIndex = ( ListItem_t* ) & ( pxList->xListEnd );			/*lint !e826 !e740 The mini list structure is used as the list end to save RAM.  This is checked and valid. */
+
     /* The list end value is the highest possible value in the list to
     ensure it remains at the end of the list. */
     pxList->xListEnd.xItemValue = portMAX_DELAY;
+
     /* The list end next and previous pointers point to itself so we know
     when the list is empty. */
     pxList->xListEnd.pxNext = ( ListItem_t* ) & ( pxList->xListEnd );	/*lint !e826 !e740 The mini list structure is used as the list end to save RAM.  This is checked and valid. */
     pxList->xListEnd.pxPrevious = ( ListItem_t* ) & ( pxList->xListEnd );/*lint !e826 !e740 The mini list structure is used as the list end to save RAM.  This is checked and valid. */
+
     pxList->uxNumberOfItems = ( UBaseType_t ) 0U;
+
     /* Write known values into the list if
     configUSE_LIST_DATA_INTEGRITY_CHECK_BYTES is set to 1. */
     listSET_LIST_INTEGRITY_CHECK_1_VALUE( pxList );
@@ -101,6 +63,7 @@ void vListInitialiseItem( ListItem_t* const pxItem )
 {
     /* Make sure the list item is not recorded as being on a list. */
     pxItem->pvContainer = NULL;
+
     /* Write known values into the list item if
     configUSE_LIST_DATA_INTEGRITY_CHECK_BYTES is set to 1. */
     listSET_FIRST_LIST_ITEM_INTEGRITY_CHECK_VALUE( pxItem );
@@ -111,22 +74,28 @@ void vListInitialiseItem( ListItem_t* const pxItem )
 void vListInsertEnd( List_t* const pxList, ListItem_t* const pxNewListItem )
 {
     ListItem_t* const pxIndex = pxList->pxIndex;
+
     /* Only effective when configASSERT() is also defined, these tests may catch
     the list data structures being overwritten in memory.  They will not catch
     data errors caused by incorrect configuration or use of FreeRTOS. */
     listTEST_LIST_INTEGRITY( pxList );
     listTEST_LIST_ITEM_INTEGRITY( pxNewListItem );
+
     /* Insert a new list item into pxList, but rather than sort the list,
     makes the new list item the last item to be removed by a call to
     listGET_OWNER_OF_NEXT_ENTRY(). */
     pxNewListItem->pxNext = pxIndex;
     pxNewListItem->pxPrevious = pxIndex->pxPrevious;
+
     /* Only used during decision coverage testing. */
     mtCOVERAGE_TEST_DELAY();
+
     pxIndex->pxPrevious->pxNext = pxNewListItem;
     pxIndex->pxPrevious = pxNewListItem;
+
     /* Remember which list the item is in. */
     pxNewListItem->pvContainer = ( void* ) pxList;
+
     ( pxList->uxNumberOfItems )++;
 }
 /*-----------------------------------------------------------*/
@@ -135,6 +104,7 @@ void vListInsert( List_t* const pxList, ListItem_t* const pxNewListItem )
 {
     ListItem_t* pxIterator;
     const TickType_t xValueOfInsertion = pxNewListItem->xItemValue;
+
     /* Only effective when configASSERT() is also defined, these tests may catch
     the list data structures being overwritten in memory.  They will not catch
     data errors caused by incorrect configuration or use of FreeRTOS. */
@@ -176,6 +146,7 @@ void vListInsert( List_t* const pxList, ListItem_t* const pxNewListItem )
         	   before the scheduler has been started (are interrupts firing
         	   before vTaskStartScheduler() has been called?).
         **********************************************************************/
+
         for ( pxIterator = ( ListItem_t* ) & ( pxList->xListEnd ); pxIterator->pxNext->xItemValue <= xValueOfInsertion; pxIterator = pxIterator->pxNext ) /*lint !e826 !e740 The mini list structure is used as the list end to save RAM.  This is checked and valid. */
         {
             /* There is nothing to do here, just iterating to the wanted
@@ -187,9 +158,11 @@ void vListInsert( List_t* const pxList, ListItem_t* const pxNewListItem )
     pxNewListItem->pxNext->pxPrevious = pxNewListItem;
     pxNewListItem->pxPrevious = pxIterator;
     pxIterator->pxNext = pxNewListItem;
+
     /* Remember which list the item is in.  This allows fast removal of the
     item later. */
     pxNewListItem->pvContainer = ( void* ) pxList;
+
     ( pxList->uxNumberOfItems )++;
 }
 /*-----------------------------------------------------------*/
@@ -199,8 +172,10 @@ UBaseType_t uxListRemove( ListItem_t* const pxItemToRemove )
     /* The list item knows which list it is in.  Obtain the list from the list
     item. */
     List_t* const pxList = ( List_t* ) pxItemToRemove->pvContainer;
+
     pxItemToRemove->pxNext->pxPrevious = pxItemToRemove->pxPrevious;
     pxItemToRemove->pxPrevious->pxNext = pxItemToRemove->pxNext;
+
     /* Only used during decision coverage testing. */
     mtCOVERAGE_TEST_DELAY();
 
@@ -216,6 +191,7 @@ UBaseType_t uxListRemove( ListItem_t* const pxItemToRemove )
 
     pxItemToRemove->pvContainer = NULL;
     ( pxList->uxNumberOfItems )--;
+
     return pxList->uxNumberOfItems;
 }
 /*-----------------------------------------------------------*/
diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/port.c b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM3/port.c
similarity index 69%
rename from EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/port.c
rename to EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM3/port.c
index 1aa434cf..04793114 100644
--- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/port.c
+++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM3/port.c
@@ -1,82 +1,43 @@
 /*
-    FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd.
-    All rights reserved
-
-    VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION.
-
-    This file is part of the FreeRTOS distribution.
-
-    FreeRTOS is free software; you can redistribute it and/or modify it under
-    the terms of the GNU General Public License (version 2) as published by the
-    Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception.
-
-    ***************************************************************************
-    >>!   NOTE: The modification to the GPL is included to allow you to     !<<
-    >>!   distribute a combined work that includes FreeRTOS without being   !<<
-    >>!   obliged to provide the source code for proprietary components     !<<
-    >>!   outside of the FreeRTOS kernel.                                   !<<
-    ***************************************************************************
-
-    FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY
-    WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
-    FOR A PARTICULAR PURPOSE.  Full license text is available on the following
-    link: http://www.freertos.org/a00114.html
-
-    ***************************************************************************
-     *                                                                       *
-     *    FreeRTOS provides completely free yet professionally developed,    *
-     *    robust, strictly quality controlled, supported, and cross          *
-     *    platform software that is more than just the market leader, it     *
-     *    is the industry's de facto standard.                               *
-     *                                                                       *
-     *    Help yourself get started quickly while simultaneously helping     *
-     *    to support the FreeRTOS project by purchasing a FreeRTOS           *
-     *    tutorial book, reference manual, or both:                          *
-     *    http://www.FreeRTOS.org/Documentation                              *
-     *                                                                       *
-    ***************************************************************************
-
-    http://www.FreeRTOS.org/FAQHelp.html - Having a problem?  Start by reading
-    the FAQ page "My application does not run, what could be wrong?".  Have you
-    defined configASSERT()?
-
-    http://www.FreeRTOS.org/support - In return for receiving this top quality
-    embedded software for free we request you assist our global community by
-    participating in the support forum.
-
-    http://www.FreeRTOS.org/training - Investing in training allows your team to
-    be as productive as possible as early as possible.  Now you can receive
-    FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers
-    Ltd, and the world's leading authority on the world's leading RTOS.
-
-    http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products,
-    including FreeRTOS+Trace - an indispensable productivity tool, a DOS
-    compatible FAT file system, and our tiny thread aware UDP/IP stack.
-
-    http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate.
-    Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS.
-
-    http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High
-    Integrity Systems ltd. to sell under the OpenRTOS brand.  Low cost OpenRTOS
-    licenses offer ticketed support, indemnification and commercial middleware.
-
-    http://www.SafeRTOS.com - High Integrity Systems also provide a safety
-    engineered and independently SIL3 certified version for use in safety and
-    mission critical applications that require provable dependability.
-
-    1 tab == 4 spaces!
-*/
+ * FreeRTOS Kernel V10.0.1
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
 
 /*-----------------------------------------------------------
- * Implementation of functions defined in portable.h for the ARM CM4F port.
+ * Implementation of functions defined in portable.h for the ARM CM3 port.
  *----------------------------------------------------------*/
 
 /* Scheduler includes. */
 #include "FreeRTOS.h"
 #include "task.h"
 
-#ifndef __VFP_FP__
-#error This port can only be used when the project options are configured to enable hardware floating point support.
+/* For backward compatibility, ensure configKERNEL_INTERRUPT_PRIORITY is
+defined.  The value should also ensure backward compatibility.
+FreeRTOS.org versions prior to V4.4.0 did not include this definition. */
+#ifndef configKERNEL_INTERRUPT_PRIORITY
+#define configKERNEL_INTERRUPT_PRIORITY 255
 #endif
 
 #ifndef configSYSTICK_CLOCK_HZ
@@ -101,12 +62,6 @@ as the core. */
 #define portNVIC_PENDSVCLEAR_BIT 			( 1UL << 27UL )
 #define portNVIC_PEND_SYSTICK_CLEAR_BIT		( 1UL << 25UL )
 
-/* Constants used to detect a Cortex-M7 r0p1 core, which should use the ARM_CM7
-r0p1 port. */
-#define portCPUID							( * ( ( volatile uint32_t * ) 0xE000ed00 ) )
-#define portCORTEX_M7_r0p1_ID				( 0x410FC271UL )
-#define portCORTEX_M7_r0p0_ID				( 0x410FC270UL )
-
 #define portNVIC_PENDSV_PRI					( ( ( uint32_t ) configKERNEL_INTERRUPT_PRIORITY ) << 16UL )
 #define portNVIC_SYSTICK_PRI				( ( ( uint32_t ) configKERNEL_INTERRUPT_PRIORITY ) << 24UL )
 
@@ -123,13 +78,8 @@ r0p1 port. */
 /* Masks off all bits but the VECTACTIVE bits in the ICSR register. */
 #define portVECTACTIVE_MASK					( 0xFFUL )
 
-/* Constants required to manipulate the VFP. */
-#define portFPCCR							( ( volatile uint32_t * ) 0xe000ef34 ) /* Floating point context control register. */
-#define portASPEN_AND_LSPEN_BITS			( 0x3UL << 30UL )
-
 /* Constants required to set up the initial stack. */
-#define portINITIAL_XPSR					( 0x01000000 )
-#define portINITIAL_EXEC_RETURN				( 0xfffffffd )
+#define portINITIAL_XPSR					( 0x01000000UL )
 
 /* The systick is a 24-bit counter. */
 #define portMAX_24_BIT_NUMBER				( 0xffffffUL )
@@ -139,6 +89,10 @@ occurred while the SysTick counter is stopped during tickless idle
 calculations. */
 #define portMISSED_COUNTS_FACTOR			( 45UL )
 
+/* For strict compliance with the Cortex-M spec the task start address should
+have bit-0 clear, as it is loaded into the PC on exit from an ISR. */
+#define portSTART_ADDRESS_MASK				( ( StackType_t ) 0xfffffffeUL )
+
 /* Let the user override the pre-loading of the initial LR with the address of
 prvTaskExitError() in case it messes up unwinding of the stack in the
 debugger. */
@@ -148,10 +102,6 @@ debugger. */
 #define portTASK_RETURN_ADDRESS	prvTaskExitError
 #endif
 
-/* Each task maintains its own interrupt status in the critical nesting
-variable. */
-static UBaseType_t uxCriticalNesting = 0xaaaaaaaa;
-
 /*
  * Setup the timer to generate the tick interrupts.  The implementation in this
  * file is weak to allow application writers to change the timer used to
@@ -171,11 +121,6 @@ void vPortSVCHandler( void ) __attribute__ (( naked ));
  */
 static void prvPortStartFirstTask( void ) __attribute__ (( naked ));
 
-/*
- * Function to enable the VFP.
- */
-static void vPortEnableVFP( void ) __attribute__ (( naked ));
-
 /*
  * Used to catch tasks that attempt to return from their implementing function.
  */
@@ -183,10 +128,14 @@ static void prvTaskExitError( void );
 
 /*-----------------------------------------------------------*/
 
+/* Each task maintains its own interrupt status in the critical nesting
+variable. */
+static UBaseType_t uxCriticalNesting = 0xaaaaaaaa;
+
 /*
  * The number of SysTick increments that make up one tick period.
  */
-#if configUSE_TICKLESS_IDLE == 1
+#if( configUSE_TICKLESS_IDLE == 1 )
 static uint32_t ulTimerCountsForOneTick = 0;
 #endif /* configUSE_TICKLESS_IDLE */
 
@@ -194,7 +143,7 @@ static uint32_t ulTimerCountsForOneTick = 0;
  * The maximum number of tick periods that can be suppressed is limited by the
  * 24 bit resolution of the SysTick timer.
  */
-#if configUSE_TICKLESS_IDLE == 1
+#if( configUSE_TICKLESS_IDLE == 1 )
 static uint32_t xMaximumPossibleSuppressedTicks = 0;
 #endif /* configUSE_TICKLESS_IDLE */
 
@@ -202,7 +151,7 @@ static uint32_t xMaximumPossibleSuppressedTicks = 0;
  * Compensate for the CPU cycles that pass while the SysTick is stopped (low
  * power functionality only.
  */
-#if configUSE_TICKLESS_IDLE == 1
+#if( configUSE_TICKLESS_IDLE == 1 )
 static uint32_t ulStoppedTimerCompensation = 0;
 #endif /* configUSE_TICKLESS_IDLE */
 
@@ -211,7 +160,7 @@ static uint32_t ulStoppedTimerCompensation = 0;
  * FreeRTOS API functions are not called from interrupts that have been assigned
  * a priority above configMAX_SYSCALL_INTERRUPT_PRIORITY.
  */
-#if ( configASSERT_DEFINED == 1 )
+#if( configASSERT_DEFINED == 1 )
 static uint8_t ucMaxSysCallPriority = 0;
 static uint32_t ulMaxPRIGROUPValue = 0;
 static const volatile uint8_t* const pcInterruptPriorityRegisters = ( const volatile uint8_t* const ) portNVIC_IP_REGISTERS_OFFSET_16;
@@ -226,28 +175,24 @@ StackType_t* pxPortInitialiseStack( StackType_t* pxTopOfStack, TaskFunction_t px
 {
     /* Simulate the stack frame as it would be created by a context switch
     interrupt. */
-    /* Offset added to account for the way the MCU uses the stack on entry/exit
-    of interrupts, and to ensure alignment. */
-    pxTopOfStack--;
+    pxTopOfStack--; /* Offset added to account for the way the MCU uses the stack on entry/exit of interrupts. */
     *pxTopOfStack = portINITIAL_XPSR;	/* xPSR */
     pxTopOfStack--;
-    *pxTopOfStack = ( StackType_t ) pxCode;	/* PC */
+    *pxTopOfStack = ( ( StackType_t ) pxCode ) & portSTART_ADDRESS_MASK;	/* PC */
     pxTopOfStack--;
     *pxTopOfStack = ( StackType_t ) portTASK_RETURN_ADDRESS;	/* LR */
-    /* Save code space by skipping register initialisation. */
     pxTopOfStack -= 5;	/* R12, R3, R2 and R1. */
     *pxTopOfStack = ( StackType_t ) pvParameters;	/* R0 */
-    /* A save method is being used that requires each task to maintain its
-    own exec return value. */
-    pxTopOfStack--;
-    *pxTopOfStack = portINITIAL_EXEC_RETURN;
     pxTopOfStack -= 8;	/* R11, R10, R9, R8, R7, R6, R5 and R4. */
+
     return pxTopOfStack;
 }
 /*-----------------------------------------------------------*/
 
 static void prvTaskExitError( void )
 {
+    volatile uint32_t ulDummy = 0UL;
+
     /* A function that implements a task must not exit or attempt to return to
     its caller as there is nothing to return to.  If a task wants to exit it
     should instead call vTaskDelete( NULL ).
@@ -257,7 +202,16 @@ static void prvTaskExitError( void )
     configASSERT( uxCriticalNesting == ~0UL );
     portDISABLE_INTERRUPTS();
 
-    for ( ;; );
+    while ( ulDummy == 0 )
+    {
+        /* This file calls prvTaskExitError() after the scheduler has been
+        started to remove a compiler warning about the function being defined
+        but never called.  ulDummy is used purely to quieten other warnings
+        about code appearing after this function is called - making ulDummy
+        volatile makes the compiler think the function could return and
+        therefore not output an 'unreachable code' warning for code that appears
+        after it. */
+    }
 }
 /*-----------------------------------------------------------*/
 
@@ -267,14 +221,15 @@ void vPortSVCHandler( void )
         "	ldr	r3, pxCurrentTCBConst2		\n" /* Restore the context. */
         "	ldr r1, [r3]					\n" /* Use pxCurrentTCBConst to get the pxCurrentTCB address. */
         "	ldr r0, [r1]					\n" /* The first item in pxCurrentTCB is the task top of stack. */
-        "	ldmia r0!, {r4-r11, r14}		\n" /* Pop the registers that are not automatically saved on exception entry and the critical nesting count. */
+        "	ldmia r0!, {r4-r11}				\n" /* Pop the registers that are not automatically saved on exception entry and the critical nesting count. */
         "	msr psp, r0						\n" /* Restore the task stack pointer. */
         "	isb								\n"
         "	mov r0, #0 						\n"
         "	msr	basepri, r0					\n"
+        "	orr r14, #0xd					\n"
         "	bx r14							\n"
         "									\n"
-        "	.align 2						\n"
+        "	.align 4						\n"
         "pxCurrentTCBConst2: .word pxCurrentTCB				\n"
     );
 }
@@ -305,16 +260,13 @@ BaseType_t xPortStartScheduler( void )
     /* configMAX_SYSCALL_INTERRUPT_PRIORITY must not be set to 0.
     See http://www.FreeRTOS.org/RTOS-Cortex-M3-M4.html */
     configASSERT( configMAX_SYSCALL_INTERRUPT_PRIORITY );
-    /* This port can be used on all revisions of the Cortex-M7 core other than
-    the r0p1 parts.  r0p1 parts should use the port from the
-    /source/portable/GCC/ARM_CM7/r0p1 directory. */
-    configASSERT( portCPUID != portCORTEX_M7_r0p1_ID );
-    configASSERT( portCPUID != portCORTEX_M7_r0p0_ID );
+
 #if( configASSERT_DEFINED == 1 )
     {
         volatile uint32_t ulOriginalPriority;
         volatile uint8_t* const pucFirstUserPriorityRegister = ( volatile uint8_t* const ) ( portNVIC_IP_REGISTERS_OFFSET_16 + portFIRST_USER_INTERRUPT_NUMBER );
         volatile uint8_t ucMaxPriorityValue;
+
         /* Determine the maximum priority from which ISR safe FreeRTOS API
         functions can be called.  ISR safe functions are those that end in
         "FromISR".  FreeRTOS maintains separate thread and ISR API functions to
@@ -322,13 +274,17 @@ BaseType_t xPortStartScheduler( void )
 
         Save the interrupt priority value that is about to be clobbered. */
         ulOriginalPriority = *pucFirstUserPriorityRegister;
+
         /* Determine the number of priority bits available.  First write to all
         possible bits. */
         *pucFirstUserPriorityRegister = portMAX_8_BIT_VALUE;
+
         /* Read the value back to see how many bits stuck. */
         ucMaxPriorityValue = *pucFirstUserPriorityRegister;
+
         /* Use the same mask on the maximum system call priority. */
         ucMaxSysCallPriority = configMAX_SYSCALL_INTERRUPT_PRIORITY & ucMaxPriorityValue;
+
         /* Calculate the maximum acceptable priority group value for the number
         of bits read back. */
         ulMaxPRIGROUPValue = portMAX_PRIGROUP_BITS;
@@ -339,34 +295,58 @@ BaseType_t xPortStartScheduler( void )
             ucMaxPriorityValue <<= ( uint8_t ) 0x01;
         }
 
+#ifdef __NVIC_PRIO_BITS
+        {
+            /* Check the CMSIS configuration that defines the number of
+            priority bits matches the number of priority bits actually queried
+            from the hardware. */
+            configASSERT( ( portMAX_PRIGROUP_BITS - ulMaxPRIGROUPValue ) == __NVIC_PRIO_BITS );
+        }
+#endif
+
+#ifdef configPRIO_BITS
+        {
+            /* Check the FreeRTOS configuration that defines the number of
+            priority bits matches the number of priority bits actually queried
+            from the hardware. */
+            configASSERT( ( portMAX_PRIGROUP_BITS - ulMaxPRIGROUPValue ) == configPRIO_BITS );
+        }
+#endif
+
         /* Shift the priority group value back to its position within the AIRCR
         register. */
         ulMaxPRIGROUPValue <<= portPRIGROUP_SHIFT;
         ulMaxPRIGROUPValue &= portPRIORITY_GROUP_MASK;
+
         /* Restore the clobbered interrupt priority register to its original
         value. */
         *pucFirstUserPriorityRegister = ulOriginalPriority;
     }
 #endif /* conifgASSERT_DEFINED */
+
     /* Make PendSV and SysTick the lowest priority interrupts. */
     portNVIC_SYSPRI2_REG |= portNVIC_PENDSV_PRI;
     portNVIC_SYSPRI2_REG |= portNVIC_SYSTICK_PRI;
+
     /* Start the timer that generates the tick ISR.  Interrupts are disabled
     here already. */
     vPortSetupTimerInterrupt();
+
     /* Initialise the critical nesting count ready for the first task. */
     uxCriticalNesting = 0;
-    /* Ensure the VFP is enabled - it should be anyway. */
-    vPortEnableVFP();
-    /* Lazy save always. */
-    *( portFPCCR ) |= portASPEN_AND_LSPEN_BITS;
+
     /* Start the first task. */
     prvPortStartFirstTask();
+
     /* Should never get here as the tasks will now be executing!  Call the task
     exit error function to prevent compiler warnings about a static function
     not being called in the case that the application writer overrides this
-    functionality by defining configTASK_RETURN_ADDRESS. */
+    functionality by defining configTASK_RETURN_ADDRESS.  Call
+    vTaskSwitchContext() so link time optimisation does not remove the
+    symbol. */
+    vTaskSwitchContext();
     prvTaskExitError();
+
     /* Should not get here! */
     return 0;
 }
@@ -412,6 +392,7 @@ void vPortExitCritical( void )
 void xPortPendSVHandler( void )
 {
     /* This is a naked function. */
+
     __asm volatile
     (
         "	mrs r0, psp							\n"
@@ -420,46 +401,25 @@ void xPortPendSVHandler( void )
         "	ldr	r3, pxCurrentTCBConst			\n" /* Get the location of the current TCB. */
         "	ldr	r2, [r3]						\n"
         "										\n"
-        "	tst r14, #0x10						\n" /* Is the task using the FPU context?  If so, push high vfp registers. */
-        "	it eq								\n"
-        "	vstmdbeq r0!, {s16-s31}				\n"
-        "										\n"
-        "	stmdb r0!, {r4-r11, r14}			\n" /* Save the core registers. */
-        "										\n"
+        "	stmdb r0!, {r4-r11}					\n" /* Save the remaining registers. */
         "	str r0, [r2]						\n" /* Save the new top of stack into the first member of the TCB. */
         "										\n"
-        "	stmdb sp!, {r3}						\n"
-        "	mov r0, %0 							\n"
+        "	stmdb sp!, {r3, r14}				\n"
+        "	mov r0, %0							\n"
         "	msr basepri, r0						\n"
-        "	dsb									\n"
-        "   isb									\n"
         "	bl vTaskSwitchContext				\n"
         "	mov r0, #0							\n"
         "	msr basepri, r0						\n"
-        "	ldmia sp!, {r3}						\n"
-        "										\n"
-        "	ldr r1, [r3]						\n" /* The first item in pxCurrentTCB is the task top of stack. */
-        "	ldr r0, [r1]						\n"
-        "										\n"
-        "	ldmia r0!, {r4-r11, r14}			\n" /* Pop the core registers. */
-        "										\n"
-        "	tst r14, #0x10						\n" /* Is the task using the FPU context?  If so, pop the high vfp registers too. */
-        "	it eq								\n"
-        "	vldmiaeq r0!, {s16-s31}				\n"
-        "										\n"
+        "	ldmia sp!, {r3, r14}				\n"
+        "										\n" /* Restore the context, including the critical nesting count. */
+        "	ldr r1, [r3]						\n"
+        "	ldr r0, [r1]						\n" /* The first item in pxCurrentTCB is the task top of stack. */
+        "	ldmia r0!, {r4-r11}					\n" /* Pop the registers. */
         "	msr psp, r0							\n"
         "	isb									\n"
-        "										\n"
-#ifdef WORKAROUND_PMU_CM001 /* XMC4000 specific errata workaround. */
-#if WORKAROUND_PMU_CM001 == 1
-        "			push { r14 }				\n"
-        "			pop { pc }					\n"
-#endif
-#endif
-        "										\n"
         "	bx r14								\n"
         "										\n"
-        "	.align 2							\n"
+        "	.align 4							\n"
         "pxCurrentTCBConst: .word pxCurrentTCB	\n"
         ::"i"(configMAX_SYSCALL_INTERRUPT_PRIORITY)
     );
@@ -472,7 +432,7 @@ void xPortSysTickHandler( void )
     executes all interrupts must be unmasked.  There is therefore no need to
     save and then restore the interrupt mask value as its value is already
     known. */
-    ( void ) portSET_INTERRUPT_MASK_FROM_ISR();
+    portDISABLE_INTERRUPTS();
     {
         /* Increment the RTOS tick. */
         if ( xTaskIncrementTick() != pdFALSE )
@@ -482,15 +442,15 @@ void xPortSysTickHandler( void )
             portNVIC_INT_CTRL_REG = portNVIC_PENDSVSET_BIT;
         }
     }
-    portCLEAR_INTERRUPT_MASK_FROM_ISR( 0 );
+    portENABLE_INTERRUPTS();
 }
 /*-----------------------------------------------------------*/
 
-#if configUSE_TICKLESS_IDLE == 1
+#if( configUSE_TICKLESS_IDLE == 1 )
 
 __attribute__((weak)) void vPortSuppressTicksAndSleep( TickType_t xExpectedIdleTime )
 {
-    uint32_t ulReloadValue, ulCompleteTickPeriods, ulCompletedSysTickDecrements, ulSysTickCTRL;
+    uint32_t ulReloadValue, ulCompleteTickPeriods, ulCompletedSysTickDecrements;
     TickType_t xModifiableIdleTime;
 
     /* Make sure the SysTick reload value does not overflow the counter. */
@@ -504,6 +464,7 @@ __attribute__((weak)) void vPortSuppressTicksAndSleep( TickType_t xExpectedIdleT
     inevitably result in some tiny drift of the time maintained by the
     kernel with respect to calendar time. */
     portNVIC_SYSTICK_CTRL_REG &= ~portNVIC_SYSTICK_ENABLE_BIT;
+
     /* Calculate the reload value required to wait xExpectedIdleTime
     tick periods.  -1 is used because this code will execute part way
     through one of the tick periods. */
@@ -516,7 +477,9 @@ __attribute__((weak)) void vPortSuppressTicksAndSleep( TickType_t xExpectedIdleT
 
     /* Enter a critical section but don't use the taskENTER_CRITICAL()
     method as that will mask interrupts that should exit sleep mode. */
-    __asm volatile( "cpsid i" );
+    __asm volatile( "cpsid i" ::: "memory" );
+    __asm volatile( "dsb" );
+    __asm volatile( "isb" );
 
     /* If a context switch is pending or a task is waiting for the scheduler
     to be unsuspended then abandon the low power entry. */
@@ -525,24 +488,30 @@ __attribute__((weak)) void vPortSuppressTicksAndSleep( TickType_t xExpectedIdleT
         /* Restart from whatever is left in the count register to complete
         this tick period. */
         portNVIC_SYSTICK_LOAD_REG = portNVIC_SYSTICK_CURRENT_VALUE_REG;
+
         /* Restart SysTick. */
         portNVIC_SYSTICK_CTRL_REG |= portNVIC_SYSTICK_ENABLE_BIT;
+
         /* Reset the reload register to the value required for normal tick
         periods. */
         portNVIC_SYSTICK_LOAD_REG = ulTimerCountsForOneTick - 1UL;
+
         /* Re-enable interrupts - see comments above the cpsid instruction()
         above. */
-        __asm volatile( "cpsie i" );
+        __asm volatile( "cpsie i" ::: "memory" );
     }
     else
     {
         /* Set the new reload value. */
         portNVIC_SYSTICK_LOAD_REG = ulReloadValue;
+
         /* Clear the SysTick count flag and set the count value back to
         zero. */
         portNVIC_SYSTICK_CURRENT_VALUE_REG = 0UL;
+
         /* Restart SysTick. */
         portNVIC_SYSTICK_CTRL_REG |= portNVIC_SYSTICK_ENABLE_BIT;
+
         /* Sleep until something happens.  configPRE_SLEEP_PROCESSING() can
         set its parameter to 0 to indicate that its implementation contains
         its own wait for interrupt or wait for event instruction, and so wfi
@@ -553,27 +522,48 @@ __attribute__((weak)) void vPortSuppressTicksAndSleep( TickType_t xExpectedIdleT
 
         if ( xModifiableIdleTime > 0 )
         {
-            __asm volatile( "dsb" );
+            __asm volatile( "dsb" ::: "memory" );
             __asm volatile( "wfi" );
             __asm volatile( "isb" );
         }
 
         configPOST_SLEEP_PROCESSING( &xExpectedIdleTime );
-        /* Stop SysTick.  Again, the time the SysTick is stopped for is
-        accounted for as best it can be, but using the tickless mode will
-        inevitably result in some tiny drift of the time maintained by the
-        kernel with respect to calendar time. */
-        ulSysTickCTRL = portNVIC_SYSTICK_CTRL_REG;
-        portNVIC_SYSTICK_CTRL_REG = ( ulSysTickCTRL & ~portNVIC_SYSTICK_ENABLE_BIT );
-        /* Re-enable interrupts - see comments above the cpsid instruction()
-        above. */
-        __asm volatile( "cpsie i" );
 
-        if ( ( ulSysTickCTRL & portNVIC_SYSTICK_COUNT_FLAG_BIT ) != 0 )
+        /* Re-enable interrupts to allow the interrupt that brought the MCU
+        out of sleep mode to execute immediately.  see comments above
+        __disable_interrupt() call above. */
+        __asm volatile( "cpsie i" ::: "memory" );
+        __asm volatile( "dsb" );
+        __asm volatile( "isb" );
+
+        /* Disable interrupts again because the clock is about to be stopped
+        and interrupts that execute while the clock is stopped will increase
+        any slippage between the time maintained by the RTOS and calendar
+        time. */
+        __asm volatile( "cpsid i" ::: "memory" );
+        __asm volatile( "dsb" );
+        __asm volatile( "isb" );
+
+        /* Disable the SysTick clock without reading the
+        portNVIC_SYSTICK_CTRL_REG register to ensure the
+        portNVIC_SYSTICK_COUNT_FLAG_BIT is not cleared if it is set.  Again,
+        the time the SysTick is stopped for is accounted for as best it can
+        be, but using the tickless mode will inevitably result in some tiny
+        drift of the time maintained by the kernel with respect to calendar
+        time*/
+        portNVIC_SYSTICK_CTRL_REG = ( portNVIC_SYSTICK_CLK_BIT | portNVIC_SYSTICK_INT_BIT );
+
+        /* Determine if the SysTick clock has already counted to zero and
+        been set back to the current reload value (the reload back being
+        correct for the entire expected idle time) or if the SysTick is yet
+        to count to zero (in which case an interrupt other than the SysTick
+        must have brought the system out of sleep mode). */
+        if ( ( portNVIC_SYSTICK_CTRL_REG & portNVIC_SYSTICK_COUNT_FLAG_BIT ) != 0 )
         {
             uint32_t ulCalculatedLoadValue;
-            /* The tick interrupt has already executed, and the SysTick
-            count reloaded with ulReloadValue.  Reset the
+
+            /* The tick interrupt is already pending, and the SysTick count
+            reloaded with ulReloadValue.  Reset the
             portNVIC_SYSTICK_LOAD_REG with whatever remains of this tick
             period. */
             ulCalculatedLoadValue = ( ulTimerCountsForOneTick - 1UL ) - ( ulReloadValue - portNVIC_SYSTICK_CURRENT_VALUE_REG );
@@ -587,11 +577,10 @@ __attribute__((weak)) void vPortSuppressTicksAndSleep( TickType_t xExpectedIdleT
             }
 
             portNVIC_SYSTICK_LOAD_REG = ulCalculatedLoadValue;
-            /* The tick interrupt handler will already have pended the tick
-            processing in the kernel.  As the pending tick will be
-            processed as soon as this function exits, the tick value
-            maintained by the tick is stepped forward by one less than the
-            time spent waiting. */
+
+            /* As the pending tick will be processed as soon as this
+            function exits, the tick value maintained by the tick is stepped
+            forward by one less than the time spent waiting. */
             ulCompleteTickPeriods = xExpectedIdleTime - 1UL;
         }
         else
@@ -601,31 +590,30 @@ __attribute__((weak)) void vPortSuppressTicksAndSleep( TickType_t xExpectedIdleT
             periods (not the ulReload value which accounted for part
             ticks). */
             ulCompletedSysTickDecrements = ( xExpectedIdleTime * ulTimerCountsForOneTick ) - portNVIC_SYSTICK_CURRENT_VALUE_REG;
+
             /* How many complete tick periods passed while the processor
             was waiting? */
             ulCompleteTickPeriods = ulCompletedSysTickDecrements / ulTimerCountsForOneTick;
+
             /* The reload value is set to whatever fraction of a single tick
             period remains. */
-            portNVIC_SYSTICK_LOAD_REG = ( ( ulCompleteTickPeriods + 1 ) * ulTimerCountsForOneTick ) - ulCompletedSysTickDecrements;
+            portNVIC_SYSTICK_LOAD_REG = ( ( ulCompleteTickPeriods + 1UL ) * ulTimerCountsForOneTick ) - ulCompletedSysTickDecrements;
         }
 
         /* Restart SysTick so it runs from portNVIC_SYSTICK_LOAD_REG
         again, then set portNVIC_SYSTICK_LOAD_REG back to its standard
-        value.  The critical section is used to ensure the tick interrupt
-        can only execute once in the case that the reload register is near
-        zero. */
+        value. */
         portNVIC_SYSTICK_CURRENT_VALUE_REG = 0UL;
-        portENTER_CRITICAL();
-        {
-            portNVIC_SYSTICK_CTRL_REG |= portNVIC_SYSTICK_ENABLE_BIT;
-            vTaskStepTick( ulCompleteTickPeriods );
-            portNVIC_SYSTICK_LOAD_REG = ulTimerCountsForOneTick - 1UL;
-        }
-        portEXIT_CRITICAL();
+        portNVIC_SYSTICK_CTRL_REG |= portNVIC_SYSTICK_ENABLE_BIT;
+        vTaskStepTick( ulCompleteTickPeriods );
+        portNVIC_SYSTICK_LOAD_REG = ulTimerCountsForOneTick - 1UL;
+
+        /* Exit with interrpts enabled. */
+        __asm volatile( "cpsie i" ::: "memory" );
     }
 }
 
-#endif /* #if configUSE_TICKLESS_IDLE */
+#endif /* configUSE_TICKLESS_IDLE */
 /*-----------------------------------------------------------*/
 
 /*
@@ -635,48 +623,40 @@ __attribute__((weak)) void vPortSuppressTicksAndSleep( TickType_t xExpectedIdleT
 __attribute__(( weak )) void vPortSetupTimerInterrupt( void )
 {
     /* Calculate the constants required to configure the tick interrupt. */
-#if configUSE_TICKLESS_IDLE == 1
+#if( configUSE_TICKLESS_IDLE == 1 )
     {
         ulTimerCountsForOneTick = ( configSYSTICK_CLOCK_HZ / configTICK_RATE_HZ );
         xMaximumPossibleSuppressedTicks = portMAX_24_BIT_NUMBER / ulTimerCountsForOneTick;
         ulStoppedTimerCompensation = portMISSED_COUNTS_FACTOR / ( configCPU_CLOCK_HZ / configSYSTICK_CLOCK_HZ );
     }
 #endif /* configUSE_TICKLESS_IDLE */
+
+    /* Stop and clear the SysTick. */
+    portNVIC_SYSTICK_CTRL_REG = 0UL;
+    portNVIC_SYSTICK_CURRENT_VALUE_REG = 0UL;
+
     /* Configure SysTick to interrupt at the requested rate. */
     portNVIC_SYSTICK_LOAD_REG = ( configSYSTICK_CLOCK_HZ / configTICK_RATE_HZ ) - 1UL;
     portNVIC_SYSTICK_CTRL_REG = ( portNVIC_SYSTICK_CLK_BIT | portNVIC_SYSTICK_INT_BIT | portNVIC_SYSTICK_ENABLE_BIT );
 }
 /*-----------------------------------------------------------*/
 
-/* This is a naked function. */
-static void vPortEnableVFP( void )
-{
-    __asm volatile
-    (
-        "	ldr.w r0, =0xE000ED88		\n" /* The FPU enable bits are in the CPACR. */
-        "	ldr r1, [r0]				\n"
-        "								\n"
-        "	orr r1, r1, #( 0xf << 20 )	\n" /* Enable CP10 and CP11 coprocessors, then save back. */
-        "	str r1, [r0]				\n"
-        "	bx r14						"
-    );
-}
-/*-----------------------------------------------------------*/
-
 #if( configASSERT_DEFINED == 1 )
 
 void vPortValidateInterruptPriority( void )
 {
     uint32_t ulCurrentInterrupt;
     uint8_t ucCurrentPriority;
+
     /* Obtain the number of the currently executing interrupt. */
-    __asm volatile( "mrs %0, ipsr" : "=r"( ulCurrentInterrupt ) );
+    __asm volatile( "mrs %0, ipsr" : "=r"( ulCurrentInterrupt ) :: "memory" );
 
     /* Is the interrupt number a user defined interrupt? */
     if ( ulCurrentInterrupt >= portFIRST_USER_INTERRUPT_NUMBER )
     {
         /* Look up the interrupt's priority. */
         ucCurrentPriority = pcInterruptPriorityRegisters[ ulCurrentInterrupt ];
+
         /* The following assertion will fail if a service routine (ISR) for
         an interrupt that has been assigned a priority above
         configMAX_SYSCALL_INTERRUPT_PRIORITY calls an ISR safe FreeRTOS API
@@ -715,10 +695,29 @@ void vPortValidateInterruptPriority( void )
     devices by calling NVIC_SetPriorityGrouping( 0 ); before starting the
     scheduler.  Note however that some vendor specific peripheral libraries
     assume a non-zero priority group setting, in which cases using a value
-    of zero will result in unpredicable behaviour. */
+    of zero will result in unpredictable behaviour. */
     configASSERT( ( portAIRCR_REG & portPRIORITY_GROUP_MASK ) <= ulMaxPRIGROUPValue );
 }
 
 #endif /* configASSERT_DEFINED */
 
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
 
diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/portmacro.h b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM3/portmacro.h
similarity index 60%
rename from EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/portmacro.h
rename to EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM3/portmacro.h
index a95a7523..80f25aba 100644
--- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/portmacro.h
+++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM3/portmacro.h
@@ -1,71 +1,29 @@
 /*
-    FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd.
-    All rights reserved
-
-    VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION.
-
-    This file is part of the FreeRTOS distribution.
-
-    FreeRTOS is free software; you can redistribute it and/or modify it under
-    the terms of the GNU General Public License (version 2) as published by the
-    Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception.
-
-    ***************************************************************************
-    >>!   NOTE: The modification to the GPL is included to allow you to     !<<
-    >>!   distribute a combined work that includes FreeRTOS without being   !<<
-    >>!   obliged to provide the source code for proprietary components     !<<
-    >>!   outside of the FreeRTOS kernel.                                   !<<
-    ***************************************************************************
-
-    FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY
-    WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
-    FOR A PARTICULAR PURPOSE.  Full license text is available on the following
-    link: http://www.freertos.org/a00114.html
-
-    ***************************************************************************
-     *                                                                       *
-     *    FreeRTOS provides completely free yet professionally developed,    *
-     *    robust, strictly quality controlled, supported, and cross          *
-     *    platform software that is more than just the market leader, it     *
-     *    is the industry's de facto standard.                               *
-     *                                                                       *
-     *    Help yourself get started quickly while simultaneously helping     *
-     *    to support the FreeRTOS project by purchasing a FreeRTOS           *
-     *    tutorial book, reference manual, or both:                          *
-     *    http://www.FreeRTOS.org/Documentation                              *
-     *                                                                       *
-    ***************************************************************************
-
-    http://www.FreeRTOS.org/FAQHelp.html - Having a problem?  Start by reading
-    the FAQ page "My application does not run, what could be wrong?".  Have you
-    defined configASSERT()?
-
-    http://www.FreeRTOS.org/support - In return for receiving this top quality
-    embedded software for free we request you assist our global community by
-    participating in the support forum.
-
-    http://www.FreeRTOS.org/training - Investing in training allows your team to
-    be as productive as possible as early as possible.  Now you can receive
-    FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers
-    Ltd, and the world's leading authority on the world's leading RTOS.
-
-    http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products,
-    including FreeRTOS+Trace - an indispensable productivity tool, a DOS
-    compatible FAT file system, and our tiny thread aware UDP/IP stack.
-
-    http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate.
-    Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS.
-
-    http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High
-    Integrity Systems ltd. to sell under the OpenRTOS brand.  Low cost OpenRTOS
-    licenses offer ticketed support, indemnification and commercial middleware.
-
-    http://www.SafeRTOS.com - High Integrity Systems also provide a safety
-    engineered and independently SIL3 certified version for use in safety and
-    mission critical applications that require provable dependability.
-
-    1 tab == 4 spaces!
-*/
+ * FreeRTOS Kernel V10.0.1
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
 
 
 #ifndef PORTMACRO_H
@@ -125,7 +83,7 @@ not need to be guarded with a critical section. */
 																				\
 	/* Barriers are normally not required but do ensure the code is completely	\
 	within the specified behaviour for the architecture. */						\
-	__asm volatile( "dsb" );													\
+	__asm volatile( "dsb" ::: "memory" );										\
 	__asm volatile( "isb" );													\
 }
 
@@ -172,7 +130,8 @@ extern void vPortSuppressTicksAndSleep( TickType_t xExpectedIdleTime );
 __attribute__( ( always_inline ) ) static inline uint8_t ucPortCountLeadingZeros( uint32_t ulBitmap )
 {
     uint8_t ucReturn;
-    __asm volatile ( "clz %0, %1" : "=r" ( ucReturn ) : "r" ( ulBitmap ) );
+
+    __asm volatile ( "clz %0, %1" : "=r" ( ucReturn ) : "r" ( ulBitmap ) : "memory" );
     return ucReturn;
 }
 
@@ -187,7 +146,7 @@ __attribute__( ( always_inline ) ) static inline uint8_t ucPortCountLeadingZeros
 
 /*-----------------------------------------------------------*/
 
-#define portGET_HIGHEST_PRIORITY( uxTopPriority, uxReadyPriorities ) uxTopPriority = ( 31 - ucPortCountLeadingZeros( ( uxReadyPriorities ) ) )
+#define portGET_HIGHEST_PRIORITY( uxTopPriority, uxReadyPriorities ) uxTopPriority = ( 31UL - ( uint32_t ) ucPortCountLeadingZeros( ( uxReadyPriorities ) ) )
 
 #endif /* configUSE_PORT_OPTIMISED_TASK_SELECTION */
 
@@ -201,22 +160,45 @@ void vPortValidateInterruptPriority( void );
 /* portNOP() is not required by this port. */
 #define portNOP()
 
+#define portINLINE	__inline
+
 #ifndef portFORCE_INLINE
 #define portFORCE_INLINE inline __attribute__(( always_inline))
 #endif
 
+portFORCE_INLINE static BaseType_t xPortIsInsideInterrupt( void )
+{
+    uint32_t ulCurrentInterrupt;
+    BaseType_t xReturn;
+
+    /* Obtain the number of the currently executing interrupt. */
+    __asm volatile( "mrs %0, ipsr" : "=r"( ulCurrentInterrupt ) :: "memory" );
+
+    if ( ulCurrentInterrupt == 0 )
+    {
+        xReturn = pdFALSE;
+    }
+    else
+    {
+        xReturn = pdTRUE;
+    }
+
+    return xReturn;
+}
+
 /*-----------------------------------------------------------*/
 
 portFORCE_INLINE static void vPortRaiseBASEPRI( void )
 {
     uint32_t ulNewBASEPRI;
+
     __asm volatile
     (
-        "	mov %0, %1												\n"	\
+        "	mov %0, %1												\n" \
         "	msr basepri, %0											\n" \
         "	isb														\n" \
         "	dsb														\n" \
-        : "=r" (ulNewBASEPRI) : "i" ( configMAX_SYSCALL_INTERRUPT_PRIORITY )
+        : "=r" (ulNewBASEPRI) : "i" ( configMAX_SYSCALL_INTERRUPT_PRIORITY ) : "memory"
     );
 }
 
@@ -225,15 +207,17 @@ portFORCE_INLINE static void vPortRaiseBASEPRI( void )
 portFORCE_INLINE static uint32_t ulPortRaiseBASEPRI( void )
 {
     uint32_t ulOriginalBASEPRI, ulNewBASEPRI;
+
     __asm volatile
     (
         "	mrs %0, basepri											\n" \
-        "	mov %1, %2												\n"	\
+        "	mov %1, %2												\n" \
         "	msr basepri, %1											\n" \
         "	isb														\n" \
         "	dsb														\n" \
-        : "=r" (ulOriginalBASEPRI), "=r" (ulNewBASEPRI) : "i" ( configMAX_SYSCALL_INTERRUPT_PRIORITY )
+        : "=r" (ulOriginalBASEPRI), "=r" (ulNewBASEPRI) : "i" ( configMAX_SYSCALL_INTERRUPT_PRIORITY ) : "memory"
     );
+
     /* This return will not be reached but is necessary to prevent compiler
     warnings. */
     return ulOriginalBASEPRI;
@@ -244,7 +228,7 @@ portFORCE_INLINE static void vPortSetBASEPRI( uint32_t ulNewMaskValue )
 {
     __asm volatile
     (
-        "	msr basepri, %0	" :: "r" ( ulNewMaskValue )
+        "	msr basepri, %0	" :: "r" ( ulNewMaskValue ) : "memory"
     );
 }
 /*-----------------------------------------------------------*/
diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/MemMang/heap_4.c b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/MemMang/heap_4.c
index a427284e..d43a5067 100644
--- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/MemMang/heap_4.c
+++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/portable/MemMang/heap_4.c
@@ -1,71 +1,29 @@
 /*
-    FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd.
-    All rights reserved
-
-    VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION.
-
-    This file is part of the FreeRTOS distribution.
-
-    FreeRTOS is free software; you can redistribute it and/or modify it under
-    the terms of the GNU General Public License (version 2) as published by the
-    Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception.
-
-    ***************************************************************************
-    >>!   NOTE: The modification to the GPL is included to allow you to     !<<
-    >>!   distribute a combined work that includes FreeRTOS without being   !<<
-    >>!   obliged to provide the source code for proprietary components     !<<
-    >>!   outside of the FreeRTOS kernel.                                   !<<
-    ***************************************************************************
-
-    FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY
-    WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
-    FOR A PARTICULAR PURPOSE.  Full license text is available on the following
-    link: http://www.freertos.org/a00114.html
-
-    ***************************************************************************
-     *                                                                       *
-     *    FreeRTOS provides completely free yet professionally developed,    *
-     *    robust, strictly quality controlled, supported, and cross          *
-     *    platform software that is more than just the market leader, it     *
-     *    is the industry's de facto standard.                               *
-     *                                                                       *
-     *    Help yourself get started quickly while simultaneously helping     *
-     *    to support the FreeRTOS project by purchasing a FreeRTOS           *
-     *    tutorial book, reference manual, or both:                          *
-     *    http://www.FreeRTOS.org/Documentation                              *
-     *                                                                       *
-    ***************************************************************************
-
-    http://www.FreeRTOS.org/FAQHelp.html - Having a problem?  Start by reading
-    the FAQ page "My application does not run, what could be wrong?".  Have you
-    defined configASSERT()?
-
-    http://www.FreeRTOS.org/support - In return for receiving this top quality
-    embedded software for free we request you assist our global community by
-    participating in the support forum.
-
-    http://www.FreeRTOS.org/training - Investing in training allows your team to
-    be as productive as possible as early as possible.  Now you can receive
-    FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers
-    Ltd, and the world's leading authority on the world's leading RTOS.
-
-    http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products,
-    including FreeRTOS+Trace - an indispensable productivity tool, a DOS
-    compatible FAT file system, and our tiny thread aware UDP/IP stack.
-
-    http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate.
-    Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS.
-
-    http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High
-    Integrity Systems ltd. to sell under the OpenRTOS brand.  Low cost OpenRTOS
-    licenses offer ticketed support, indemnification and commercial middleware.
-
-    http://www.SafeRTOS.com - High Integrity Systems also provide a safety
-    engineered and independently SIL3 certified version for use in safety and
-    mission critical applications that require provable dependability.
-
-    1 tab == 4 spaces!
-*/
+ * FreeRTOS Kernel V10.0.1
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
 
 /*
  * A sample implementation of pvPortMalloc() and vPortFree() that combines
@@ -87,6 +45,10 @@ task.h is included from an application file. */
 
 #undef MPU_WRAPPERS_INCLUDED_FROM_API_FILE
 
+#if( configSUPPORT_DYNAMIC_ALLOCATION == 0 )
+#error This file must not be used if configSUPPORT_DYNAMIC_ALLOCATION is 0
+#endif
+
 /* Block sizes must not get too small. */
 #define heapMINIMUM_BLOCK_SIZE	( ( size_t ) ( xHeapStructSize << 1 ) )
 
@@ -152,6 +114,7 @@ void* pvPortMalloc( size_t xWantedSize )
 {
     BlockLink_t* pxBlock, *pxPreviousBlock, *pxNewBlockLink;
     void* pvReturn = NULL;
+
     vTaskSuspendAll();
     {
         /* If this is the first call to malloc then the heap will require
@@ -215,6 +178,7 @@ void* pvPortMalloc( size_t xWantedSize )
                     /* Return the memory space pointed to - jumping over the
                     BlockLink_t structure at its start. */
                     pvReturn = ( void* ) ( ( ( uint8_t* ) pxPreviousBlock->pxNextFreeBlock ) + xHeapStructSize );
+
                     /* This block is being returned for use so must be taken out
                     of the list of free blocks. */
                     pxPreviousBlock->pxNextFreeBlock = pxBlock->pxNextFreeBlock;
@@ -229,10 +193,12 @@ void* pvPortMalloc( size_t xWantedSize )
                         compiler. */
                         pxNewBlockLink = ( void* ) ( ( ( uint8_t* ) pxBlock ) + xWantedSize );
                         configASSERT( ( ( ( size_t ) pxNewBlockLink ) & portBYTE_ALIGNMENT_MASK ) == 0 );
+
                         /* Calculate the sizes of two blocks split from the
                         single block. */
                         pxNewBlockLink->xBlockSize = pxBlock->xBlockSize - xWantedSize;
                         pxBlock->xBlockSize = xWantedSize;
+
                         /* Insert the new block into the list of free blocks. */
                         prvInsertBlockIntoFreeList( pxNewBlockLink );
                     }
@@ -275,6 +241,7 @@ void* pvPortMalloc( size_t xWantedSize )
         traceMALLOC( pvReturn, xWantedSize );
     }
     ( void ) xTaskResumeAll();
+
 #if( configUSE_MALLOC_FAILED_HOOK == 1 )
     {
         if ( pvReturn == NULL )
@@ -288,7 +255,8 @@ void* pvPortMalloc( size_t xWantedSize )
         }
     }
 #endif
-    configASSERT( ( ( ( uint32_t ) pvReturn ) & portBYTE_ALIGNMENT_MASK ) == 0 );
+
+    configASSERT( ( ( ( size_t ) pvReturn ) & ( size_t ) portBYTE_ALIGNMENT_MASK ) == 0 );
     return pvReturn;
 }
 /*-----------------------------------------------------------*/
@@ -303,8 +271,10 @@ void vPortFree( void* pv )
         /* The memory being freed will have an BlockLink_t structure immediately
         before it. */
         puc -= xHeapStructSize;
+
         /* This casting is to keep the compiler from issuing warnings. */
         pxLink = ( void* ) puc;
+
         /* Check the block is actually allocated. */
         configASSERT( ( pxLink->xBlockSize & xBlockAllocatedBit ) != 0 );
         configASSERT( pxLink->pxNextFreeBlock == NULL );
@@ -316,6 +286,7 @@ void vPortFree( void* pv )
                 /* The block is being returned to the heap - it is no longer
                 allocated. */
                 pxLink->xBlockSize &= ~xBlockAllocatedBit;
+
                 vTaskSuspendAll();
                 {
                     /* Add this block to the list of free blocks. */
@@ -362,6 +333,7 @@ static void prvHeapInit( void )
     uint8_t* pucAlignedHeap;
     size_t uxAddress;
     size_t xTotalHeapSize = configTOTAL_HEAP_SIZE;
+
     /* Ensure the heap starts on a correctly aligned boundary. */
     uxAddress = ( size_t ) ucHeap;
 
@@ -373,10 +345,12 @@ static void prvHeapInit( void )
     }
 
     pucAlignedHeap = ( uint8_t* ) uxAddress;
+
     /* xStart is used to hold a pointer to the first item in the list of free
     blocks.  The void cast is used to prevent compiler warnings. */
     xStart.pxNextFreeBlock = ( void* ) pucAlignedHeap;
     xStart.xBlockSize = ( size_t ) 0;
+
     /* pxEnd is used to mark the end of the list of free blocks and is inserted
     at the end of the heap space. */
     uxAddress = ( ( size_t ) pucAlignedHeap ) + xTotalHeapSize;
@@ -385,14 +359,17 @@ static void prvHeapInit( void )
     pxEnd = ( void* ) uxAddress;
     pxEnd->xBlockSize = 0;
     pxEnd->pxNextFreeBlock = NULL;
+
     /* To start with there is a single free block that is sized to take up the
     entire heap space, minus the space taken by pxEnd. */
     pxFirstFreeBlock = ( void* ) pucAlignedHeap;
     pxFirstFreeBlock->xBlockSize = uxAddress - ( size_t ) pxFirstFreeBlock;
     pxFirstFreeBlock->pxNextFreeBlock = pxEnd;
+
     /* Only one block exists - and it covers the entire usable heap space. */
     xMinimumEverFreeBytesRemaining = pxFirstFreeBlock->xBlockSize;
     xFreeBytesRemaining = pxFirstFreeBlock->xBlockSize;
+
     /* Work out the position of the top bit in a size_t variable. */
     xBlockAllocatedBit = ( ( size_t ) 1 ) << ( ( sizeof( size_t ) * heapBITS_PER_BYTE ) - 1 );
 }
diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/queue.c b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/queue.c
index 995fa19c..e3bce41e 100644
--- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/queue.c
+++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/queue.c
@@ -1,71 +1,29 @@
 /*
-    FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd.
-    All rights reserved
-
-    VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION.
-
-    This file is part of the FreeRTOS distribution.
-
-    FreeRTOS is free software; you can redistribute it and/or modify it under
-    the terms of the GNU General Public License (version 2) as published by the
-    Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception.
-
-    ***************************************************************************
-    >>!   NOTE: The modification to the GPL is included to allow you to     !<<
-    >>!   distribute a combined work that includes FreeRTOS without being   !<<
-    >>!   obliged to provide the source code for proprietary components     !<<
-    >>!   outside of the FreeRTOS kernel.                                   !<<
-    ***************************************************************************
-
-    FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY
-    WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
-    FOR A PARTICULAR PURPOSE.  Full license text is available on the following
-    link: http://www.freertos.org/a00114.html
-
-    ***************************************************************************
-     *                                                                       *
-     *    FreeRTOS provides completely free yet professionally developed,    *
-     *    robust, strictly quality controlled, supported, and cross          *
-     *    platform software that is more than just the market leader, it     *
-     *    is the industry's de facto standard.                               *
-     *                                                                       *
-     *    Help yourself get started quickly while simultaneously helping     *
-     *    to support the FreeRTOS project by purchasing a FreeRTOS           *
-     *    tutorial book, reference manual, or both:                          *
-     *    http://www.FreeRTOS.org/Documentation                              *
-     *                                                                       *
-    ***************************************************************************
-
-    http://www.FreeRTOS.org/FAQHelp.html - Having a problem?  Start by reading
-    the FAQ page "My application does not run, what could be wrong?".  Have you
-    defined configASSERT()?
-
-    http://www.FreeRTOS.org/support - In return for receiving this top quality
-    embedded software for free we request you assist our global community by
-    participating in the support forum.
-
-    http://www.FreeRTOS.org/training - Investing in training allows your team to
-    be as productive as possible as early as possible.  Now you can receive
-    FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers
-    Ltd, and the world's leading authority on the world's leading RTOS.
-
-    http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products,
-    including FreeRTOS+Trace - an indispensable productivity tool, a DOS
-    compatible FAT file system, and our tiny thread aware UDP/IP stack.
-
-    http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate.
-    Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS.
-
-    http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High
-    Integrity Systems ltd. to sell under the OpenRTOS brand.  Low cost OpenRTOS
-    licenses offer ticketed support, indemnification and commercial middleware.
-
-    http://www.SafeRTOS.com - High Integrity Systems also provide a safety
-    engineered and independently SIL3 certified version for use in safety and
-    mission critical applications that require provable dependability.
-
-    1 tab == 4 spaces!
-*/
+ * FreeRTOS Kernel V10.0.1
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
 
 #include 
 #include 
@@ -90,9 +48,9 @@ privileged Vs unprivileged linkage and placement. */
 #undef MPU_WRAPPERS_INCLUDED_FROM_API_FILE /*lint !e961 !e750. */
 
 
-/* Constants used with the xRxLock and xTxLock structure members. */
-#define queueUNLOCKED					( ( BaseType_t ) -1 )
-#define queueLOCKED_UNMODIFIED			( ( BaseType_t ) 0 )
+/* Constants used with the cRxLock and cTxLock structure members. */
+#define queueUNLOCKED					( ( int8_t ) -1 )
+#define queueLOCKED_UNMODIFIED			( ( int8_t ) 0 )
 
 /* When the Queue_t structure is used to represent a base queue its pcHead and
 pcTail members are used as pointers into the queue storage area.  When the
@@ -146,18 +104,22 @@ typedef struct QueueDefinition
     UBaseType_t uxLength;			/*< The length of the queue defined as the number of items it will hold, not the number of bytes. */
     UBaseType_t uxItemSize;			/*< The size of each items that the queue will hold. */
 
-    volatile BaseType_t xRxLock;	/*< Stores the number of items received from the queue (removed from the queue) while the queue was locked.  Set to queueUNLOCKED when the queue is not locked. */
-    volatile BaseType_t xTxLock;	/*< Stores the number of items transmitted to the queue (added to the queue) while the queue was locked.  Set to queueUNLOCKED when the queue is not locked. */
+    volatile int8_t cRxLock;		/*< Stores the number of items received from the queue (removed from the queue) while the queue was locked.  Set to queueUNLOCKED when the queue is not locked. */
+    volatile int8_t cTxLock;		/*< Stores the number of items transmitted to the queue (added to the queue) while the queue was locked.  Set to queueUNLOCKED when the queue is not locked. */
 
-#if ( configUSE_TRACE_FACILITY == 1 )
-    UBaseType_t uxQueueNumber;
-    uint8_t ucQueueType;
+#if( ( configSUPPORT_STATIC_ALLOCATION == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) )
+    uint8_t ucStaticallyAllocated;	/*< Set to pdTRUE if the memory used by the queue was statically allocated to ensure no attempt is made to free the memory. */
 #endif
 
 #if ( configUSE_QUEUE_SETS == 1 )
     struct QueueDefinition* pxQueueSetContainer;
 #endif
 
+#if ( configUSE_TRACE_FACILITY == 1 )
+    UBaseType_t uxQueueNumber;
+    uint8_t ucQueueType;
+#endif
+
 } xQUEUE;
 
 /* The old xQUEUE name is maintained above then typedefed to the new Queue_t
@@ -236,6 +198,31 @@ static void prvCopyDataFromQueue( Queue_t* const pxQueue, void* const pvBuffer )
 static BaseType_t prvNotifyQueueSetContainer( const Queue_t* const pxQueue, const BaseType_t xCopyPosition ) PRIVILEGED_FUNCTION;
 #endif
 
+/*
+ * Called after a Queue_t structure has been allocated either statically or
+ * dynamically to fill in the structure's members.
+ */
+static void prvInitialiseNewQueue( const UBaseType_t uxQueueLength, const UBaseType_t uxItemSize, uint8_t* pucQueueStorage, const uint8_t ucQueueType, Queue_t* pxNewQueue ) PRIVILEGED_FUNCTION;
+
+/*
+ * Mutexes are a special type of queue.  When a mutex is created, first the
+ * queue is created, then prvInitialiseMutex() is called to configure the queue
+ * as a mutex.
+ */
+#if( configUSE_MUTEXES == 1 )
+static void prvInitialiseMutex( Queue_t* pxNewQueue ) PRIVILEGED_FUNCTION;
+#endif
+
+#if( configUSE_MUTEXES == 1 )
+/*
+ * If a task waiting for a mutex causes the mutex holder to inherit a
+ * priority, but the waiting task times out, then the holder should
+ * disinherit the priority - but only down to the highest priority of any
+ * other tasks that are waiting for the same mutex.  This function returns
+ * that priority.
+ */
+static UBaseType_t prvGetDisinheritPriorityAfterTimeout( const Queue_t* const pxQueue ) PRIVILEGED_FUNCTION;
+#endif
 /*-----------------------------------------------------------*/
 
 /*
@@ -245,13 +232,13 @@ static BaseType_t prvNotifyQueueSetContainer( const Queue_t* const pxQueue, cons
 #define prvLockQueue( pxQueue )								\
 	taskENTER_CRITICAL();									\
 	{														\
-		if( ( pxQueue )->xRxLock == queueUNLOCKED )			\
+		if( ( pxQueue )->cRxLock == queueUNLOCKED )			\
 		{													\
-			( pxQueue )->xRxLock = queueLOCKED_UNMODIFIED;	\
+			( pxQueue )->cRxLock = queueLOCKED_UNMODIFIED;	\
 		}													\
-		if( ( pxQueue )->xTxLock == queueUNLOCKED )			\
+		if( ( pxQueue )->cTxLock == queueUNLOCKED )			\
 		{													\
-			( pxQueue )->xTxLock = queueLOCKED_UNMODIFIED;	\
+			( pxQueue )->cTxLock = queueLOCKED_UNMODIFIED;	\
 		}													\
 	}														\
 	taskEXIT_CRITICAL()
@@ -260,15 +247,17 @@ static BaseType_t prvNotifyQueueSetContainer( const Queue_t* const pxQueue, cons
 BaseType_t xQueueGenericReset( QueueHandle_t xQueue, BaseType_t xNewQueue )
 {
     Queue_t* const pxQueue = ( Queue_t* ) xQueue;
+
     configASSERT( pxQueue );
+
     taskENTER_CRITICAL();
     {
         pxQueue->pcTail = pxQueue->pcHead + ( pxQueue->uxLength * pxQueue->uxItemSize );
         pxQueue->uxMessagesWaiting = ( UBaseType_t ) 0U;
         pxQueue->pcWriteTo = pxQueue->pcHead;
         pxQueue->u.pcReadFrom = pxQueue->pcHead + ( ( pxQueue->uxLength - ( UBaseType_t ) 1U ) * pxQueue->uxItemSize );
-        pxQueue->xRxLock = queueUNLOCKED;
-        pxQueue->xTxLock = queueUNLOCKED;
+        pxQueue->cRxLock = queueUNLOCKED;
+        pxQueue->cTxLock = queueUNLOCKED;
 
         if ( xNewQueue == pdFALSE )
         {
@@ -279,7 +268,7 @@ BaseType_t xQueueGenericReset( QueueHandle_t xQueue, BaseType_t xNewQueue )
             it will be possible to write to it. */
             if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToSend ) ) == pdFALSE )
             {
-                if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToSend ) ) == pdTRUE )
+                if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToSend ) ) != pdFALSE )
                 {
                     queueYIELD_IF_USING_PREEMPTION();
                 }
@@ -301,20 +290,77 @@ BaseType_t xQueueGenericReset( QueueHandle_t xQueue, BaseType_t xNewQueue )
         }
     }
     taskEXIT_CRITICAL();
+
     /* A value is returned for calling semantic consistency with previous
     versions. */
     return pdPASS;
 }
 /*-----------------------------------------------------------*/
 
+#if( configSUPPORT_STATIC_ALLOCATION == 1 )
+
+QueueHandle_t xQueueGenericCreateStatic( const UBaseType_t uxQueueLength, const UBaseType_t uxItemSize, uint8_t* pucQueueStorage, StaticQueue_t* pxStaticQueue, const uint8_t ucQueueType )
+{
+    Queue_t* pxNewQueue;
+
+    configASSERT( uxQueueLength > ( UBaseType_t ) 0 );
+
+    /* The StaticQueue_t structure and the queue storage area must be
+    supplied. */
+    configASSERT( pxStaticQueue != NULL );
+
+    /* A queue storage area should be provided if the item size is not 0, and
+    should not be provided if the item size is 0. */
+    configASSERT( !( ( pucQueueStorage != NULL ) && ( uxItemSize == 0 ) ) );
+    configASSERT( !( ( pucQueueStorage == NULL ) && ( uxItemSize != 0 ) ) );
+
+#if( configASSERT_DEFINED == 1 )
+    {
+        /* Sanity check that the size of the structure used to declare a
+        variable of type StaticQueue_t or StaticSemaphore_t equals the size of
+        the real queue and semaphore structures. */
+        volatile size_t xSize = sizeof( StaticQueue_t );
+        configASSERT( xSize == sizeof( Queue_t ) );
+    }
+#endif /* configASSERT_DEFINED */
+
+    /* The address of a statically allocated queue was passed in, use it.
+    The address of a statically allocated storage area was also passed in
+    but is already set. */
+    pxNewQueue = ( Queue_t* ) pxStaticQueue;  /*lint !e740 Unusual cast is ok as the structures are designed to have the same alignment, and the size is checked by an assert. */
+
+    if ( pxNewQueue != NULL )
+    {
+#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 )
+        {
+            /* Queues can be allocated wither statically or dynamically, so
+            note this queue was allocated statically in case the queue is
+            later deleted. */
+            pxNewQueue->ucStaticallyAllocated = pdTRUE;
+        }
+#endif /* configSUPPORT_DYNAMIC_ALLOCATION */
+
+        prvInitialiseNewQueue( uxQueueLength, uxItemSize, pucQueueStorage, ucQueueType, pxNewQueue );
+    }
+    else
+    {
+        traceQUEUE_CREATE_FAILED( ucQueueType );
+    }
+
+    return pxNewQueue;
+}
+
+#endif /* configSUPPORT_STATIC_ALLOCATION */
+/*-----------------------------------------------------------*/
+
+#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 )
+
 QueueHandle_t xQueueGenericCreate( const UBaseType_t uxQueueLength, const UBaseType_t uxItemSize, const uint8_t ucQueueType )
 {
     Queue_t* pxNewQueue;
     size_t xQueueSizeInBytes;
-    QueueHandle_t xReturn = NULL;
-    /* Remove compiler warnings about unused parameters should
-    configUSE_TRACE_FACILITY not be set to 1. */
-    ( void ) ucQueueType;
+    uint8_t* pucQueueStorage;
+
     configASSERT( uxQueueLength > ( UBaseType_t ) 0 );
 
     if ( uxItemSize == ( UBaseType_t ) 0 )
@@ -324,101 +370,101 @@ QueueHandle_t xQueueGenericCreate( const UBaseType_t uxQueueLength, const UBaseT
     }
     else
     {
-        /* The queue is one byte longer than asked for to make wrap checking
-        easier/faster. */
-        xQueueSizeInBytes = ( size_t ) ( uxQueueLength * uxItemSize ) + ( size_t ) 1; /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
+        /* Allocate enough space to hold the maximum number of items that
+        can be in the queue at any time. */
+        xQueueSizeInBytes = ( size_t ) ( uxQueueLength * uxItemSize ); /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
     }
 
-    /* Allocate the new queue structure and storage area. */
     pxNewQueue = ( Queue_t* ) pvPortMalloc( sizeof( Queue_t ) + xQueueSizeInBytes );
 
     if ( pxNewQueue != NULL )
     {
-        if ( uxItemSize == ( UBaseType_t ) 0 )
-        {
-            /* No RAM was allocated for the queue storage area, but PC head
-            cannot be set to NULL because NULL is used as a key to say the queue
-            is used as a mutex.  Therefore just set pcHead to point to the queue
-            as a benign value that is known to be within the memory map. */
-            pxNewQueue->pcHead = ( int8_t* ) pxNewQueue;
-        }
-        else
-        {
-            /* Jump past the queue structure to find the location of the queue
-            storage area. */
-            pxNewQueue->pcHead = ( ( int8_t* ) pxNewQueue ) + sizeof( Queue_t );
-        }
+        /* Jump past the queue structure to find the location of the queue
+        storage area. */
+        pucQueueStorage = ( ( uint8_t* ) pxNewQueue ) + sizeof( Queue_t );
 
-        /* Initialise the queue members as described above where the queue type
-        is defined. */
-        pxNewQueue->uxLength = uxQueueLength;
-        pxNewQueue->uxItemSize = uxItemSize;
-        ( void ) xQueueGenericReset( pxNewQueue, pdTRUE );
-#if ( configUSE_TRACE_FACILITY == 1 )
-        {
-            pxNewQueue->ucQueueType = ucQueueType;
-        }
-#endif /* configUSE_TRACE_FACILITY */
-#if( configUSE_QUEUE_SETS == 1 )
+#if( configSUPPORT_STATIC_ALLOCATION == 1 )
         {
-            pxNewQueue->pxQueueSetContainer = NULL;
+            /* Queues can be created either statically or dynamically, so
+            note this task was created dynamically in case it is later
+            deleted. */
+            pxNewQueue->ucStaticallyAllocated = pdFALSE;
         }
-#endif /* configUSE_QUEUE_SETS */
-        traceQUEUE_CREATE( pxNewQueue );
-        xReturn = pxNewQueue;
+#endif /* configSUPPORT_STATIC_ALLOCATION */
+
+        prvInitialiseNewQueue( uxQueueLength, uxItemSize, pucQueueStorage, ucQueueType, pxNewQueue );
     }
     else
     {
-        mtCOVERAGE_TEST_MARKER();
+        traceQUEUE_CREATE_FAILED( ucQueueType );
     }
 
-    configASSERT( xReturn );
-    return xReturn;
+    return pxNewQueue;
 }
-/*-----------------------------------------------------------*/
 
-#if ( configUSE_MUTEXES == 1 )
+#endif /* configSUPPORT_STATIC_ALLOCATION */
+/*-----------------------------------------------------------*/
 
-QueueHandle_t xQueueCreateMutex( const uint8_t ucQueueType )
+static void prvInitialiseNewQueue( const UBaseType_t uxQueueLength, const UBaseType_t uxItemSize, uint8_t* pucQueueStorage, const uint8_t ucQueueType, Queue_t* pxNewQueue )
 {
-    Queue_t* pxNewQueue;
-    /* Prevent compiler warnings about unused parameters if
-    configUSE_TRACE_FACILITY does not equal 1. */
+    /* Remove compiler warnings about unused parameters should
+    configUSE_TRACE_FACILITY not be set to 1. */
     ( void ) ucQueueType;
-    /* Allocate the new queue structure. */
-    pxNewQueue = ( Queue_t* ) pvPortMalloc( sizeof( Queue_t ) );
 
+    if ( uxItemSize == ( UBaseType_t ) 0 )
+    {
+        /* No RAM was allocated for the queue storage area, but PC head cannot
+        be set to NULL because NULL is used as a key to say the queue is used as
+        a mutex.  Therefore just set pcHead to point to the queue as a benign
+        value that is known to be within the memory map. */
+        pxNewQueue->pcHead = ( int8_t* ) pxNewQueue;
+    }
+    else
+    {
+        /* Set the head to the start of the queue storage area. */
+        pxNewQueue->pcHead = ( int8_t* ) pucQueueStorage;
+    }
+
+    /* Initialise the queue members as described where the queue type is
+    defined. */
+    pxNewQueue->uxLength = uxQueueLength;
+    pxNewQueue->uxItemSize = uxItemSize;
+    ( void ) xQueueGenericReset( pxNewQueue, pdTRUE );
+
+#if ( configUSE_TRACE_FACILITY == 1 )
+    {
+        pxNewQueue->ucQueueType = ucQueueType;
+    }
+#endif /* configUSE_TRACE_FACILITY */
+
+#if( configUSE_QUEUE_SETS == 1 )
+    {
+        pxNewQueue->pxQueueSetContainer = NULL;
+    }
+#endif /* configUSE_QUEUE_SETS */
+
+    traceQUEUE_CREATE( pxNewQueue );
+}
+/*-----------------------------------------------------------*/
+
+#if( configUSE_MUTEXES == 1 )
+
+static void prvInitialiseMutex( Queue_t* pxNewQueue )
+{
     if ( pxNewQueue != NULL )
     {
-        /* Information required for priority inheritance. */
+        /* The queue create function will set all the queue structure members
+        correctly for a generic queue, but this function is creating a
+        mutex.  Overwrite those members that need to be set differently -
+        in particular the information required for priority inheritance. */
         pxNewQueue->pxMutexHolder = NULL;
         pxNewQueue->uxQueueType = queueQUEUE_IS_MUTEX;
-        /* Queues used as a mutex no data is actually copied into or out
-        of the queue. */
-        pxNewQueue->pcWriteTo = NULL;
-        pxNewQueue->u.pcReadFrom = NULL;
-        /* Each mutex has a length of 1 (like a binary semaphore) and
-        an item size of 0 as nothing is actually copied into or out
-        of the mutex. */
-        pxNewQueue->uxMessagesWaiting = ( UBaseType_t ) 0U;
-        pxNewQueue->uxLength = ( UBaseType_t ) 1U;
-        pxNewQueue->uxItemSize = ( UBaseType_t ) 0U;
-        pxNewQueue->xRxLock = queueUNLOCKED;
-        pxNewQueue->xTxLock = queueUNLOCKED;
-#if ( configUSE_TRACE_FACILITY == 1 )
-        {
-            pxNewQueue->ucQueueType = ucQueueType;
-        }
-#endif
-#if ( configUSE_QUEUE_SETS == 1 )
-        {
-            pxNewQueue->pxQueueSetContainer = NULL;
-        }
-#endif
-        /* Ensure the event queues start with the correct state. */
-        vListInitialise( &( pxNewQueue->xTasksWaitingToSend ) );
-        vListInitialise( &( pxNewQueue->xTasksWaitingToReceive ) );
+
+        /* In case this is a recursive mutex. */
+        pxNewQueue->u.uxRecursiveCallCount = 0;
+
         traceCREATE_MUTEX( pxNewQueue );
+
         /* Start with the semaphore in the expected state. */
         ( void ) xQueueGenericSend( pxNewQueue, NULL, ( TickType_t ) 0U, queueSEND_TO_BACK );
     }
@@ -426,6 +472,40 @@ QueueHandle_t xQueueCreateMutex( const uint8_t ucQueueType )
     {
         traceCREATE_MUTEX_FAILED();
     }
+}
+
+#endif /* configUSE_MUTEXES */
+/*-----------------------------------------------------------*/
+
+#if( ( configUSE_MUTEXES == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) )
+
+QueueHandle_t xQueueCreateMutex( const uint8_t ucQueueType )
+{
+    Queue_t* pxNewQueue;
+    const UBaseType_t uxMutexLength = ( UBaseType_t ) 1, uxMutexSize = ( UBaseType_t ) 0;
+
+    pxNewQueue = ( Queue_t* ) xQueueGenericCreate( uxMutexLength, uxMutexSize, ucQueueType );
+    prvInitialiseMutex( pxNewQueue );
+
+    return pxNewQueue;
+}
+
+#endif /* configUSE_MUTEXES */
+/*-----------------------------------------------------------*/
+
+#if( ( configUSE_MUTEXES == 1 ) && ( configSUPPORT_STATIC_ALLOCATION == 1 ) )
+
+QueueHandle_t xQueueCreateMutexStatic( const uint8_t ucQueueType, StaticQueue_t* pxStaticQueue )
+{
+    Queue_t* pxNewQueue;
+    const UBaseType_t uxMutexLength = ( UBaseType_t ) 1, uxMutexSize = ( UBaseType_t ) 0;
+
+    /* Prevent compiler warnings about unused parameters if
+    configUSE_TRACE_FACILITY does not equal 1. */
+    ( void ) ucQueueType;
+
+    pxNewQueue = ( Queue_t* ) xQueueGenericCreateStatic( uxMutexLength, uxMutexSize, NULL, pxStaticQueue, ucQueueType );
+    prvInitialiseMutex( pxNewQueue );
 
     return pxNewQueue;
 }
@@ -438,6 +518,7 @@ QueueHandle_t xQueueCreateMutex( const uint8_t ucQueueType )
 void* xQueueGetMutexHolder( QueueHandle_t xSemaphore )
 {
     void* pxReturn;
+
     /* This function is called by xSemaphoreGetMutexHolder(), and should not
     be called directly.  Note:  This is a good way of determining if the
     calling task is the mutex holder, but not a good way of determining the
@@ -455,6 +536,33 @@ void* xQueueGetMutexHolder( QueueHandle_t xSemaphore )
         }
     }
     taskEXIT_CRITICAL();
+
+    return pxReturn;
+} /*lint !e818 xSemaphore cannot be a pointer to const because it is a typedef. */
+
+#endif
+/*-----------------------------------------------------------*/
+
+#if ( ( configUSE_MUTEXES == 1 ) && ( INCLUDE_xSemaphoreGetMutexHolder == 1 ) )
+
+void* xQueueGetMutexHolderFromISR( QueueHandle_t xSemaphore )
+{
+    void* pxReturn;
+
+    configASSERT( xSemaphore );
+
+    /* Mutexes cannot be used in interrupt service routines, so the mutex
+    holder should not change in an ISR, and therefore a critical section is
+    not required here. */
+    if ( ( ( Queue_t* ) xSemaphore )->uxQueueType == queueQUEUE_IS_MUTEX )
+    {
+        pxReturn = ( void* ) ( ( Queue_t* ) xSemaphore )->pxMutexHolder;
+    }
+    else
+    {
+        pxReturn = NULL;
+    }
+
     return pxReturn;
 } /*lint !e818 xSemaphore cannot be a pointer to const because it is a typedef. */
 
@@ -467,6 +575,7 @@ BaseType_t xQueueGiveMutexRecursive( QueueHandle_t xMutex )
 {
     BaseType_t xReturn;
     Queue_t* const pxMutex = ( Queue_t* ) xMutex;
+
     configASSERT( pxMutex );
 
     /* If this is the task that holds the mutex then pxMutexHolder will not
@@ -478,6 +587,7 @@ BaseType_t xQueueGiveMutexRecursive( QueueHandle_t xMutex )
     if ( pxMutex->pxMutexHolder == ( void* ) xTaskGetCurrentTaskHandle() ) /*lint !e961 Not a redundant cast as TaskHandle_t is a typedef. */
     {
         traceGIVE_MUTEX_RECURSIVE( pxMutex );
+
         /* uxRecursiveCallCount cannot be zero if pxMutexHolder is equal to
         the task handle, therefore no underflow check is required.  Also,
         uxRecursiveCallCount is only modified by the mutex holder, and as
@@ -485,7 +595,7 @@ BaseType_t xQueueGiveMutexRecursive( QueueHandle_t xMutex )
         uxRecursiveCallCount member. */
         ( pxMutex->u.uxRecursiveCallCount )--;
 
-        /* Have we unwound the call count? */
+        /* Has the recursive call count unwound to 0? */
         if ( pxMutex->u.uxRecursiveCallCount == ( UBaseType_t ) 0 )
         {
             /* Return the mutex.  This will automatically unblock any other
@@ -504,6 +614,7 @@ BaseType_t xQueueGiveMutexRecursive( QueueHandle_t xMutex )
         /* The mutex cannot be given because the calling task is not the
         holder. */
         xReturn = pdFAIL;
+
         traceGIVE_MUTEX_RECURSIVE_FAILED( pxMutex );
     }
 
@@ -519,9 +630,12 @@ BaseType_t xQueueTakeMutexRecursive( QueueHandle_t xMutex, TickType_t xTicksToWa
 {
     BaseType_t xReturn;
     Queue_t* const pxMutex = ( Queue_t* ) xMutex;
+
     configASSERT( pxMutex );
+
     /* Comments regarding mutual exclusion as per those within
     xQueueGiveMutexRecursive(). */
+
     traceTAKE_MUTEX_RECURSIVE( pxMutex );
 
     if ( pxMutex->pxMutexHolder == ( void* ) xTaskGetCurrentTaskHandle() ) /*lint !e961 Cast is not redundant as TaskHandle_t is a typedef. */
@@ -531,12 +645,12 @@ BaseType_t xQueueTakeMutexRecursive( QueueHandle_t xMutex, TickType_t xTicksToWa
     }
     else
     {
-        xReturn = xQueueGenericReceive( pxMutex, NULL, xTicksToWait, pdFALSE );
+        xReturn = xQueueSemaphoreTake( pxMutex, xTicksToWait );
 
         /* pdPASS will only be returned if the mutex was successfully
         obtained.  The calling task may have entered the Blocked state
         before reaching here. */
-        if ( xReturn == pdPASS )
+        if ( xReturn != pdFAIL )
         {
             ( pxMutex->u.uxRecursiveCallCount )++;
         }
@@ -552,18 +666,49 @@ BaseType_t xQueueTakeMutexRecursive( QueueHandle_t xMutex, TickType_t xTicksToWa
 #endif /* configUSE_RECURSIVE_MUTEXES */
 /*-----------------------------------------------------------*/
 
-#if ( configUSE_COUNTING_SEMAPHORES == 1 )
+#if( ( configUSE_COUNTING_SEMAPHORES == 1 ) && ( configSUPPORT_STATIC_ALLOCATION == 1 ) )
+
+QueueHandle_t xQueueCreateCountingSemaphoreStatic( const UBaseType_t uxMaxCount, const UBaseType_t uxInitialCount, StaticQueue_t* pxStaticQueue )
+{
+    QueueHandle_t xHandle;
+
+    configASSERT( uxMaxCount != 0 );
+    configASSERT( uxInitialCount <= uxMaxCount );
+
+    xHandle = xQueueGenericCreateStatic( uxMaxCount, queueSEMAPHORE_QUEUE_ITEM_LENGTH, NULL, pxStaticQueue, queueQUEUE_TYPE_COUNTING_SEMAPHORE );
+
+    if ( xHandle != NULL )
+    {
+        ( ( Queue_t* ) xHandle )->uxMessagesWaiting = uxInitialCount;
+
+        traceCREATE_COUNTING_SEMAPHORE();
+    }
+    else
+    {
+        traceCREATE_COUNTING_SEMAPHORE_FAILED();
+    }
+
+    return xHandle;
+}
+
+#endif /* ( ( configUSE_COUNTING_SEMAPHORES == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) ) */
+/*-----------------------------------------------------------*/
+
+#if( ( configUSE_COUNTING_SEMAPHORES == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) )
 
 QueueHandle_t xQueueCreateCountingSemaphore( const UBaseType_t uxMaxCount, const UBaseType_t uxInitialCount )
 {
     QueueHandle_t xHandle;
+
     configASSERT( uxMaxCount != 0 );
     configASSERT( uxInitialCount <= uxMaxCount );
+
     xHandle = xQueueGenericCreate( uxMaxCount, queueSEMAPHORE_QUEUE_ITEM_LENGTH, queueQUEUE_TYPE_COUNTING_SEMAPHORE );
 
     if ( xHandle != NULL )
     {
         ( ( Queue_t* ) xHandle )->uxMessagesWaiting = uxInitialCount;
+
         traceCREATE_COUNTING_SEMAPHORE();
     }
     else
@@ -571,11 +716,10 @@ QueueHandle_t xQueueCreateCountingSemaphore( const UBaseType_t uxMaxCount, const
         traceCREATE_COUNTING_SEMAPHORE_FAILED();
     }
 
-    configASSERT( xHandle );
     return xHandle;
 }
 
-#endif /* configUSE_COUNTING_SEMAPHORES */
+#endif /* ( ( configUSE_COUNTING_SEMAPHORES == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) ) */
 /*-----------------------------------------------------------*/
 
 BaseType_t xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQueue, TickType_t xTicksToWait, const BaseType_t xCopyPosition )
@@ -583,6 +727,7 @@ BaseType_t xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQu
     BaseType_t xEntryTimeSet = pdFALSE, xYieldRequired;
     TimeOut_t xTimeOut;
     Queue_t* const pxQueue = ( Queue_t* ) xQueue;
+
     configASSERT( pxQueue );
     configASSERT( !( ( pvItemToQueue == NULL ) && ( pxQueue->uxItemSize != ( UBaseType_t ) 0U ) ) );
     configASSERT( !( ( xCopyPosition == queueOVERWRITE ) && ( pxQueue->uxLength != 1 ) ) );
@@ -592,6 +737,7 @@ BaseType_t xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQu
     }
 #endif
 
+
     /* This function relaxes the coding standard somewhat to allow return
     statements within the function itself.  This is done in the interest
     of execution time efficiency. */
@@ -607,11 +753,12 @@ BaseType_t xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQu
             {
                 traceQUEUE_SEND( pxQueue );
                 xYieldRequired = prvCopyDataToQueue( pxQueue, pvItemToQueue, xCopyPosition );
+
 #if ( configUSE_QUEUE_SETS == 1 )
                 {
                     if ( pxQueue->pxQueueSetContainer != NULL )
                     {
-                        if ( prvNotifyQueueSetContainer( pxQueue, xCopyPosition ) == pdTRUE )
+                        if ( prvNotifyQueueSetContainer( pxQueue, xCopyPosition ) != pdFALSE )
                         {
                             /* The queue is a member of a queue set, and posting
                             to the queue set caused a higher priority task to
@@ -629,7 +776,7 @@ BaseType_t xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQu
                         queue then unblock it now. */
                         if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToReceive ) ) == pdFALSE )
                         {
-                            if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToReceive ) ) == pdTRUE )
+                            if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToReceive ) ) != pdFALSE )
                             {
                                 /* The unblocked task has a priority higher than
                                 our own so yield immediately.  Yes it is ok to
@@ -662,7 +809,7 @@ BaseType_t xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQu
                     queue then unblock it now. */
                     if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToReceive ) ) == pdFALSE )
                     {
-                        if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToReceive ) ) == pdTRUE )
+                        if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToReceive ) ) != pdFALSE )
                         {
                             /* The unblocked task has a priority higher than
                             our own so yield immediately.  Yes it is ok to do
@@ -689,6 +836,7 @@ BaseType_t xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQu
                     }
                 }
 #endif /* configUSE_QUEUE_SETS */
+
                 taskEXIT_CRITICAL();
                 return pdPASS;
             }
@@ -699,6 +847,7 @@ BaseType_t xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQu
                     /* The queue was full and no block time is specified (or
                     the block time has expired) so leave now. */
                     taskEXIT_CRITICAL();
+
                     /* Return to the original privilege level before exiting
                     the function. */
                     traceQUEUE_SEND_FAILED( pxQueue );
@@ -708,7 +857,7 @@ BaseType_t xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQu
                 {
                     /* The queue was full and a block time was specified so
                     configure the timeout structure. */
-                    vTaskSetTimeOutState( &xTimeOut );
+                    vTaskInternalSetTimeOutState( &xTimeOut );
                     xEntryTimeSet = pdTRUE;
                 }
                 else
@@ -719,8 +868,10 @@ BaseType_t xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQu
             }
         }
         taskEXIT_CRITICAL();
+
         /* Interrupts and other tasks can send to and receive from the queue
         now the critical section has been exited. */
+
         vTaskSuspendAll();
         prvLockQueue( pxQueue );
 
@@ -731,9 +882,10 @@ BaseType_t xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQu
             {
                 traceBLOCKING_ON_QUEUE_SEND( pxQueue );
                 vTaskPlaceOnEventList( &( pxQueue->xTasksWaitingToSend ), xTicksToWait );
+
                 /* Unlocking the queue means queue events can effect the
-                event list.  It is possible	that interrupts occurring now
-                remove this task from the event	list again - but as the
+                event list.  It is possible that interrupts occurring now
+                remove this task from the event list again - but as the
                 scheduler is suspended the task will go onto the pending
                 ready last instead of the actual ready list. */
                 prvUnlockQueue( pxQueue );
@@ -760,8 +912,7 @@ BaseType_t xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQu
             /* The timeout has expired. */
             prvUnlockQueue( pxQueue );
             ( void ) xTaskResumeAll();
-            /* Return to the original privilege level before exiting the
-            function. */
+
             traceQUEUE_SEND_FAILED( pxQueue );
             return errQUEUE_FULL;
         }
@@ -769,274 +920,45 @@ BaseType_t xQueueGenericSend( QueueHandle_t xQueue, const void* const pvItemToQu
 }
 /*-----------------------------------------------------------*/
 
-#if ( configUSE_ALTERNATIVE_API == 1 )
-
-BaseType_t xQueueAltGenericSend( QueueHandle_t xQueue, const void* const pvItemToQueue, TickType_t xTicksToWait, BaseType_t xCopyPosition )
+BaseType_t xQueueGenericSendFromISR( QueueHandle_t xQueue, const void* const pvItemToQueue, BaseType_t* const pxHigherPriorityTaskWoken, const BaseType_t xCopyPosition )
 {
-    BaseType_t xEntryTimeSet = pdFALSE;
-    TimeOut_t xTimeOut;
+    BaseType_t xReturn;
+    UBaseType_t uxSavedInterruptStatus;
     Queue_t* const pxQueue = ( Queue_t* ) xQueue;
+
     configASSERT( pxQueue );
     configASSERT( !( ( pvItemToQueue == NULL ) && ( pxQueue->uxItemSize != ( UBaseType_t ) 0U ) ) );
+    configASSERT( !( ( xCopyPosition == queueOVERWRITE ) && ( pxQueue->uxLength != 1 ) ) );
 
-    for ( ;; )
+    /* RTOS ports that support interrupt nesting have the concept of a maximum
+    system call (or maximum API call) interrupt priority.  Interrupts that are
+    above the maximum system call priority are kept permanently enabled, even
+    when the RTOS kernel is in a critical section, but cannot make any calls to
+    FreeRTOS API functions.  If configASSERT() is defined in FreeRTOSConfig.h
+    then portASSERT_IF_INTERRUPT_PRIORITY_INVALID() will result in an assertion
+    failure if a FreeRTOS API function is called from an interrupt that has been
+    assigned a priority above the configured maximum system call priority.
+    Only FreeRTOS functions that end in FromISR can be called from interrupts
+    that have been assigned a priority at or (logically) below the maximum
+    system call	interrupt priority.  FreeRTOS maintains a separate interrupt
+    safe API to ensure interrupt entry is as fast and as simple as possible.
+    More information (albeit Cortex-M specific) is provided on the following
+    link: http://www.freertos.org/RTOS-Cortex-M3-M4.html */
+    portASSERT_IF_INTERRUPT_PRIORITY_INVALID();
+
+    /* Similar to xQueueGenericSend, except without blocking if there is no room
+    in the queue.  Also don't directly wake a task that was blocked on a queue
+    read, instead return a flag to say whether a context switch is required or
+    not (i.e. has a task with a higher priority than us been woken by this
+    post). */
+    uxSavedInterruptStatus = portSET_INTERRUPT_MASK_FROM_ISR();
     {
-        taskENTER_CRITICAL();
+        if ( ( pxQueue->uxMessagesWaiting < pxQueue->uxLength ) || ( xCopyPosition == queueOVERWRITE ) )
         {
-            /* Is there room on the queue now?  To be running we must be
-            the highest priority task wanting to access the queue. */
-            if ( pxQueue->uxMessagesWaiting < pxQueue->uxLength )
-            {
-                traceQUEUE_SEND( pxQueue );
-                prvCopyDataToQueue( pxQueue, pvItemToQueue, xCopyPosition );
+            const int8_t cTxLock = pxQueue->cTxLock;
 
-                /* If there was a task waiting for data to arrive on the
-                queue then unblock it now. */
-                if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToReceive ) ) == pdFALSE )
-                {
-                    if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToReceive ) ) == pdTRUE )
-                    {
-                        /* The unblocked task has a priority higher than
-                        our own so yield immediately. */
-                        portYIELD_WITHIN_API();
-                    }
-                    else
-                    {
-                        mtCOVERAGE_TEST_MARKER();
-                    }
-                }
-                else
-                {
-                    mtCOVERAGE_TEST_MARKER();
-                }
+            traceQUEUE_SEND_FROM_ISR( pxQueue );
 
-                taskEXIT_CRITICAL();
-                return pdPASS;
-            }
-            else
-            {
-                if ( xTicksToWait == ( TickType_t ) 0 )
-                {
-                    taskEXIT_CRITICAL();
-                    return errQUEUE_FULL;
-                }
-                else if ( xEntryTimeSet == pdFALSE )
-                {
-                    vTaskSetTimeOutState( &xTimeOut );
-                    xEntryTimeSet = pdTRUE;
-                }
-            }
-        }
-        taskEXIT_CRITICAL();
-        taskENTER_CRITICAL();
-        {
-            if ( xTaskCheckForTimeOut( &xTimeOut, &xTicksToWait ) == pdFALSE )
-            {
-                if ( prvIsQueueFull( pxQueue ) != pdFALSE )
-                {
-                    traceBLOCKING_ON_QUEUE_SEND( pxQueue );
-                    vTaskPlaceOnEventList( &( pxQueue->xTasksWaitingToSend ), xTicksToWait );
-                    portYIELD_WITHIN_API();
-                }
-                else
-                {
-                    mtCOVERAGE_TEST_MARKER();
-                }
-            }
-            else
-            {
-                taskEXIT_CRITICAL();
-                traceQUEUE_SEND_FAILED( pxQueue );
-                return errQUEUE_FULL;
-            }
-        }
-        taskEXIT_CRITICAL();
-    }
-}
-
-#endif /* configUSE_ALTERNATIVE_API */
-/*-----------------------------------------------------------*/
-
-#if ( configUSE_ALTERNATIVE_API == 1 )
-
-BaseType_t xQueueAltGenericReceive( QueueHandle_t xQueue, void* const pvBuffer, TickType_t xTicksToWait, BaseType_t xJustPeeking )
-{
-    BaseType_t xEntryTimeSet = pdFALSE;
-    TimeOut_t xTimeOut;
-    int8_t* pcOriginalReadPosition;
-    Queue_t* const pxQueue = ( Queue_t* ) xQueue;
-    configASSERT( pxQueue );
-    configASSERT( !( ( pvBuffer == NULL ) && ( pxQueue->uxItemSize != ( UBaseType_t ) 0U ) ) );
-
-    for ( ;; )
-    {
-        taskENTER_CRITICAL();
-        {
-            if ( pxQueue->uxMessagesWaiting > ( UBaseType_t ) 0 )
-            {
-                /* Remember our read position in case we are just peeking. */
-                pcOriginalReadPosition = pxQueue->u.pcReadFrom;
-                prvCopyDataFromQueue( pxQueue, pvBuffer );
-
-                if ( xJustPeeking == pdFALSE )
-                {
-                    traceQUEUE_RECEIVE( pxQueue );
-                    /* Data is actually being removed (not just peeked). */
-                    --( pxQueue->uxMessagesWaiting );
-#if ( configUSE_MUTEXES == 1 )
-                    {
-                        if ( pxQueue->uxQueueType == queueQUEUE_IS_MUTEX )
-                        {
-                            /* Record the information required to implement
-                            priority inheritance should it become necessary. */
-                            pxQueue->pxMutexHolder = ( int8_t* ) xTaskGetCurrentTaskHandle();
-                        }
-                        else
-                        {
-                            mtCOVERAGE_TEST_MARKER();
-                        }
-                    }
-#endif
-
-                    if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToSend ) ) == pdFALSE )
-                    {
-                        if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToSend ) ) == pdTRUE )
-                        {
-                            portYIELD_WITHIN_API();
-                        }
-                        else
-                        {
-                            mtCOVERAGE_TEST_MARKER();
-                        }
-                    }
-                }
-                else
-                {
-                    traceQUEUE_PEEK( pxQueue );
-                    /* The data is not being removed, so reset our read
-                    pointer. */
-                    pxQueue->u.pcReadFrom = pcOriginalReadPosition;
-
-                    /* The data is being left in the queue, so see if there are
-                    any other tasks waiting for the data. */
-                    if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToReceive ) ) == pdFALSE )
-                    {
-                        /* Tasks that are removed from the event list will get added to
-                        the pending ready list as the scheduler is still suspended. */
-                        if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToReceive ) ) != pdFALSE )
-                        {
-                            /* The task waiting has a higher priority than this task. */
-                            portYIELD_WITHIN_API();
-                        }
-                        else
-                        {
-                            mtCOVERAGE_TEST_MARKER();
-                        }
-                    }
-                    else
-                    {
-                        mtCOVERAGE_TEST_MARKER();
-                    }
-                }
-
-                taskEXIT_CRITICAL();
-                return pdPASS;
-            }
-            else
-            {
-                if ( xTicksToWait == ( TickType_t ) 0 )
-                {
-                    taskEXIT_CRITICAL();
-                    traceQUEUE_RECEIVE_FAILED( pxQueue );
-                    return errQUEUE_EMPTY;
-                }
-                else if ( xEntryTimeSet == pdFALSE )
-                {
-                    vTaskSetTimeOutState( &xTimeOut );
-                    xEntryTimeSet = pdTRUE;
-                }
-            }
-        }
-        taskEXIT_CRITICAL();
-        taskENTER_CRITICAL();
-        {
-            if ( xTaskCheckForTimeOut( &xTimeOut, &xTicksToWait ) == pdFALSE )
-            {
-                if ( prvIsQueueEmpty( pxQueue ) != pdFALSE )
-                {
-                    traceBLOCKING_ON_QUEUE_RECEIVE( pxQueue );
-#if ( configUSE_MUTEXES == 1 )
-                    {
-                        if ( pxQueue->uxQueueType == queueQUEUE_IS_MUTEX )
-                        {
-                            taskENTER_CRITICAL();
-                            {
-                                vTaskPriorityInherit( ( void* ) pxQueue->pxMutexHolder );
-                            }
-                            taskEXIT_CRITICAL();
-                        }
-                        else
-                        {
-                            mtCOVERAGE_TEST_MARKER();
-                        }
-                    }
-#endif
-                    vTaskPlaceOnEventList( &( pxQueue->xTasksWaitingToReceive ), xTicksToWait );
-                    portYIELD_WITHIN_API();
-                }
-                else
-                {
-                    mtCOVERAGE_TEST_MARKER();
-                }
-            }
-            else
-            {
-                taskEXIT_CRITICAL();
-                traceQUEUE_RECEIVE_FAILED( pxQueue );
-                return errQUEUE_EMPTY;
-            }
-        }
-        taskEXIT_CRITICAL();
-    }
-}
-
-
-#endif /* configUSE_ALTERNATIVE_API */
-/*-----------------------------------------------------------*/
-
-BaseType_t xQueueGenericSendFromISR( QueueHandle_t xQueue, const void* const pvItemToQueue, BaseType_t* const pxHigherPriorityTaskWoken, const BaseType_t xCopyPosition )
-{
-    BaseType_t xReturn;
-    UBaseType_t uxSavedInterruptStatus;
-    Queue_t* const pxQueue = ( Queue_t* ) xQueue;
-    configASSERT( pxQueue );
-    configASSERT( !( ( pvItemToQueue == NULL ) && ( pxQueue->uxItemSize != ( UBaseType_t ) 0U ) ) );
-    configASSERT( !( ( xCopyPosition == queueOVERWRITE ) && ( pxQueue->uxLength != 1 ) ) );
-    /* RTOS ports that support interrupt nesting have the concept of a maximum
-    system call (or maximum API call) interrupt priority.  Interrupts that are
-    above the maximum system call priority are kept permanently enabled, even
-    when the RTOS kernel is in a critical section, but cannot make any calls to
-    FreeRTOS API functions.  If configASSERT() is defined in FreeRTOSConfig.h
-    then portASSERT_IF_INTERRUPT_PRIORITY_INVALID() will result in an assertion
-    failure if a FreeRTOS API function is called from an interrupt that has been
-    assigned a priority above the configured maximum system call priority.
-    Only FreeRTOS functions that end in FromISR can be called from interrupts
-    that have been assigned a priority at or (logically) below the maximum
-    system call	interrupt priority.  FreeRTOS maintains a separate interrupt
-    safe API to ensure interrupt entry is as fast and as simple as possible.
-    More information (albeit Cortex-M specific) is provided on the following
-    link: http://www.freertos.org/RTOS-Cortex-M3-M4.html */
-    portASSERT_IF_INTERRUPT_PRIORITY_INVALID();
-    /* Similar to xQueueGenericSend, except without blocking if there is no room
-    in the queue.  Also don't directly wake a task that was blocked on a queue
-    read, instead return a flag to say whether a context switch is required or
-    not (i.e. has a task with a higher priority than us been woken by this
-    post). */
-    uxSavedInterruptStatus = portSET_INTERRUPT_MASK_FROM_ISR();
-    {
-        if ( ( pxQueue->uxMessagesWaiting < pxQueue->uxLength ) || ( xCopyPosition == queueOVERWRITE ) )
-        {
-            traceQUEUE_SEND_FROM_ISR( pxQueue );
             /* Semaphores use xQueueGiveFromISR(), so pxQueue will not be a
             semaphore or mutex.  That means prvCopyDataToQueue() cannot result
             in a task disinheriting a priority and prvCopyDataToQueue() can be
@@ -1046,13 +968,13 @@ BaseType_t xQueueGenericSendFromISR( QueueHandle_t xQueue, const void* const pvI
 
             /* The event list is not altered if the queue is locked.  This will
             be done when the queue is unlocked later. */
-            if ( pxQueue->xTxLock == queueUNLOCKED )
+            if ( cTxLock == queueUNLOCKED )
             {
 #if ( configUSE_QUEUE_SETS == 1 )
                 {
                     if ( pxQueue->pxQueueSetContainer != NULL )
                     {
-                        if ( prvNotifyQueueSetContainer( pxQueue, xCopyPosition ) == pdTRUE )
+                        if ( prvNotifyQueueSetContainer( pxQueue, xCopyPosition ) != pdFALSE )
                         {
                             /* The queue is a member of a queue set, and posting
                             to the queue set caused a higher priority task to
@@ -1132,7 +1054,7 @@ BaseType_t xQueueGenericSendFromISR( QueueHandle_t xQueue, const void* const pvI
             {
                 /* Increment the lock count so the task that unlocks the queue
                 knows that data was posted while it was locked. */
-                ++( pxQueue->xTxLock );
+                pxQueue->cTxLock = ( int8_t ) ( cTxLock + 1 );
             }
 
             xReturn = pdPASS;
@@ -1144,6 +1066,7 @@ BaseType_t xQueueGenericSendFromISR( QueueHandle_t xQueue, const void* const pvI
         }
     }
     portCLEAR_INTERRUPT_MASK_FROM_ISR( uxSavedInterruptStatus );
+
     return xReturn;
 }
 /*-----------------------------------------------------------*/
@@ -1153,19 +1076,24 @@ BaseType_t xQueueGiveFromISR( QueueHandle_t xQueue, BaseType_t* const pxHigherPr
     BaseType_t xReturn;
     UBaseType_t uxSavedInterruptStatus;
     Queue_t* const pxQueue = ( Queue_t* ) xQueue;
+
     /* Similar to xQueueGenericSendFromISR() but used with semaphores where the
     item size is 0.  Don't directly wake a task that was blocked on a queue
     read, instead return a flag to say whether a context switch is required or
     not (i.e. has a task with a higher priority than us been woken by this
     post). */
+
     configASSERT( pxQueue );
+
     /* xQueueGenericSendFromISR() should be used instead of xQueueGiveFromISR()
     if the item size is not 0. */
     configASSERT( pxQueue->uxItemSize == 0 );
+
     /* Normally a mutex would not be given from an interrupt, especially if
     there is a mutex holder, as priority inheritance makes no sense for an
     interrupts, only tasks. */
     configASSERT( !( ( pxQueue->uxQueueType == queueQUEUE_IS_MUTEX ) && ( pxQueue->pxMutexHolder != NULL ) ) );
+
     /* RTOS ports that support interrupt nesting have the concept of a maximum
     system call (or maximum API call) interrupt priority.  Interrupts that are
     above the maximum system call priority are kept permanently enabled, even
@@ -1181,31 +1109,37 @@ BaseType_t xQueueGiveFromISR( QueueHandle_t xQueue, BaseType_t* const pxHigherPr
     More information (albeit Cortex-M specific) is provided on the following
     link: http://www.freertos.org/RTOS-Cortex-M3-M4.html */
     portASSERT_IF_INTERRUPT_PRIORITY_INVALID();
+
     uxSavedInterruptStatus = portSET_INTERRUPT_MASK_FROM_ISR();
     {
+        const UBaseType_t uxMessagesWaiting = pxQueue->uxMessagesWaiting;
+
         /* When the queue is used to implement a semaphore no data is ever
         moved through the queue but it is still valid to see if the queue 'has
         space'. */
-        if ( pxQueue->uxMessagesWaiting < pxQueue->uxLength )
+        if ( uxMessagesWaiting < pxQueue->uxLength )
         {
+            const int8_t cTxLock = pxQueue->cTxLock;
+
             traceQUEUE_SEND_FROM_ISR( pxQueue );
+
             /* A task can only have an inherited priority if it is a mutex
             holder - and if there is a mutex holder then the mutex cannot be
             given from an ISR.  As this is the ISR version of the function it
             can be assumed there is no mutex holder and no need to determine if
             priority disinheritance is needed.  Simply increase the count of
             messages (semaphores) available. */
-            ++( pxQueue->uxMessagesWaiting );
+            pxQueue->uxMessagesWaiting = uxMessagesWaiting + ( UBaseType_t ) 1;
 
             /* The event list is not altered if the queue is locked.  This will
             be done when the queue is unlocked later. */
-            if ( pxQueue->xTxLock == queueUNLOCKED )
+            if ( cTxLock == queueUNLOCKED )
             {
 #if ( configUSE_QUEUE_SETS == 1 )
                 {
                     if ( pxQueue->pxQueueSetContainer != NULL )
                     {
-                        if ( prvNotifyQueueSetContainer( pxQueue, queueSEND_TO_BACK ) == pdTRUE )
+                        if ( prvNotifyQueueSetContainer( pxQueue, queueSEND_TO_BACK ) != pdFALSE )
                         {
                             /* The semaphore is a member of a queue set, and
                             posting	to the queue set caused a higher priority
@@ -1254,67 +1188,438 @@ BaseType_t xQueueGiveFromISR( QueueHandle_t xQueue, BaseType_t* const pxHigherPr
                 }
 #else /* configUSE_QUEUE_SETS */
                 {
-                    if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToReceive ) ) == pdFALSE )
+                    if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToReceive ) ) == pdFALSE )
+                    {
+                        if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToReceive ) ) != pdFALSE )
+                        {
+                            /* The task waiting has a higher priority so record that a
+                            context	switch is required. */
+                            if ( pxHigherPriorityTaskWoken != NULL )
+                            {
+                                *pxHigherPriorityTaskWoken = pdTRUE;
+                            }
+                            else
+                            {
+                                mtCOVERAGE_TEST_MARKER();
+                            }
+                        }
+                        else
+                        {
+                            mtCOVERAGE_TEST_MARKER();
+                        }
+                    }
+                    else
+                    {
+                        mtCOVERAGE_TEST_MARKER();
+                    }
+                }
+#endif /* configUSE_QUEUE_SETS */
+            }
+            else
+            {
+                /* Increment the lock count so the task that unlocks the queue
+                knows that data was posted while it was locked. */
+                pxQueue->cTxLock = ( int8_t ) ( cTxLock + 1 );
+            }
+
+            xReturn = pdPASS;
+        }
+        else
+        {
+            traceQUEUE_SEND_FROM_ISR_FAILED( pxQueue );
+            xReturn = errQUEUE_FULL;
+        }
+    }
+    portCLEAR_INTERRUPT_MASK_FROM_ISR( uxSavedInterruptStatus );
+
+    return xReturn;
+}
+/*-----------------------------------------------------------*/
+
+BaseType_t xQueueReceive( QueueHandle_t xQueue, void* const pvBuffer, TickType_t xTicksToWait )
+{
+    BaseType_t xEntryTimeSet = pdFALSE;
+    TimeOut_t xTimeOut;
+    Queue_t* const pxQueue = ( Queue_t* ) xQueue;
+
+    /* Check the pointer is not NULL. */
+    configASSERT( ( pxQueue ) );
+
+    /* The buffer into which data is received can only be NULL if the data size
+    is zero (so no data is copied into the buffer. */
+    configASSERT( !( ( ( pvBuffer ) == NULL ) && ( ( pxQueue )->uxItemSize != ( UBaseType_t ) 0U ) ) );
+
+    /* Cannot block if the scheduler is suspended. */
+#if ( ( INCLUDE_xTaskGetSchedulerState == 1 ) || ( configUSE_TIMERS == 1 ) )
+    {
+        configASSERT( !( ( xTaskGetSchedulerState() == taskSCHEDULER_SUSPENDED ) && ( xTicksToWait != 0 ) ) );
+    }
+#endif
+
+    /* This function relaxes the coding standard somewhat to allow return
+    statements within the function itself.  This is done in the interest
+    of execution time efficiency. */
+
+    for ( ;; )
+    {
+        taskENTER_CRITICAL();
+        {
+            const UBaseType_t uxMessagesWaiting = pxQueue->uxMessagesWaiting;
+
+            /* Is there data in the queue now?  To be running the calling task
+            must be the highest priority task wanting to access the queue. */
+            if ( uxMessagesWaiting > ( UBaseType_t ) 0 )
+            {
+                /* Data available, remove one item. */
+                prvCopyDataFromQueue( pxQueue, pvBuffer );
+                traceQUEUE_RECEIVE( pxQueue );
+                pxQueue->uxMessagesWaiting = uxMessagesWaiting - ( UBaseType_t ) 1;
+
+                /* There is now space in the queue, were any tasks waiting to
+                post to the queue?  If so, unblock the highest priority waiting
+                task. */
+                if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToSend ) ) == pdFALSE )
+                {
+                    if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToSend ) ) != pdFALSE )
+                    {
+                        queueYIELD_IF_USING_PREEMPTION();
+                    }
+                    else
+                    {
+                        mtCOVERAGE_TEST_MARKER();
+                    }
+                }
+                else
+                {
+                    mtCOVERAGE_TEST_MARKER();
+                }
+
+                taskEXIT_CRITICAL();
+                return pdPASS;
+            }
+            else
+            {
+                if ( xTicksToWait == ( TickType_t ) 0 )
+                {
+                    /* The queue was empty and no block time is specified (or
+                    the block time has expired) so leave now. */
+                    taskEXIT_CRITICAL();
+                    traceQUEUE_RECEIVE_FAILED( pxQueue );
+                    return errQUEUE_EMPTY;
+                }
+                else if ( xEntryTimeSet == pdFALSE )
+                {
+                    /* The queue was empty and a block time was specified so
+                    configure the timeout structure. */
+                    vTaskInternalSetTimeOutState( &xTimeOut );
+                    xEntryTimeSet = pdTRUE;
+                }
+                else
+                {
+                    /* Entry time was already set. */
+                    mtCOVERAGE_TEST_MARKER();
+                }
+            }
+        }
+        taskEXIT_CRITICAL();
+
+        /* Interrupts and other tasks can send to and receive from the queue
+        now the critical section has been exited. */
+
+        vTaskSuspendAll();
+        prvLockQueue( pxQueue );
+
+        /* Update the timeout state to see if it has expired yet. */
+        if ( xTaskCheckForTimeOut( &xTimeOut, &xTicksToWait ) == pdFALSE )
+        {
+            /* The timeout has not expired.  If the queue is still empty place
+            the task on the list of tasks waiting to receive from the queue. */
+            if ( prvIsQueueEmpty( pxQueue ) != pdFALSE )
+            {
+                traceBLOCKING_ON_QUEUE_RECEIVE( pxQueue );
+                vTaskPlaceOnEventList( &( pxQueue->xTasksWaitingToReceive ), xTicksToWait );
+                prvUnlockQueue( pxQueue );
+
+                if ( xTaskResumeAll() == pdFALSE )
+                {
+                    portYIELD_WITHIN_API();
+                }
+                else
+                {
+                    mtCOVERAGE_TEST_MARKER();
+                }
+            }
+            else
+            {
+                /* The queue contains data again.  Loop back to try and read the
+                data. */
+                prvUnlockQueue( pxQueue );
+                ( void ) xTaskResumeAll();
+            }
+        }
+        else
+        {
+            /* Timed out.  If there is no data in the queue exit, otherwise loop
+            back and attempt to read the data. */
+            prvUnlockQueue( pxQueue );
+            ( void ) xTaskResumeAll();
+
+            if ( prvIsQueueEmpty( pxQueue ) != pdFALSE )
+            {
+                traceQUEUE_RECEIVE_FAILED( pxQueue );
+                return errQUEUE_EMPTY;
+            }
+            else
+            {
+                mtCOVERAGE_TEST_MARKER();
+            }
+        }
+    }
+}
+/*-----------------------------------------------------------*/
+
+BaseType_t xQueueSemaphoreTake( QueueHandle_t xQueue, TickType_t xTicksToWait )
+{
+    BaseType_t xEntryTimeSet = pdFALSE;
+    TimeOut_t xTimeOut;
+    Queue_t* const pxQueue = ( Queue_t* ) xQueue;
+
+#if( configUSE_MUTEXES == 1 )
+    BaseType_t xInheritanceOccurred = pdFALSE;
+#endif
+
+    /* Check the queue pointer is not NULL. */
+    configASSERT( ( pxQueue ) );
+
+    /* Check this really is a semaphore, in which case the item size will be
+    0. */
+    configASSERT( pxQueue->uxItemSize == 0 );
+
+    /* Cannot block if the scheduler is suspended. */
+#if ( ( INCLUDE_xTaskGetSchedulerState == 1 ) || ( configUSE_TIMERS == 1 ) )
+    {
+        configASSERT( !( ( xTaskGetSchedulerState() == taskSCHEDULER_SUSPENDED ) && ( xTicksToWait != 0 ) ) );
+    }
+#endif
+
+
+    /* This function relaxes the coding standard somewhat to allow return
+    statements within the function itself.  This is done in the interest
+    of execution time efficiency. */
+
+    for ( ;; )
+    {
+        taskENTER_CRITICAL();
+        {
+            /* Semaphores are queues with an item size of 0, and where the
+            number of messages in the queue is the semaphore's count value. */
+            const UBaseType_t uxSemaphoreCount = pxQueue->uxMessagesWaiting;
+
+            /* Is there data in the queue now?  To be running the calling task
+            must be the highest priority task wanting to access the queue. */
+            if ( uxSemaphoreCount > ( UBaseType_t ) 0 )
+            {
+                traceQUEUE_RECEIVE( pxQueue );
+
+                /* Semaphores are queues with a data size of zero and where the
+                messages waiting is the semaphore's count.  Reduce the count. */
+                pxQueue->uxMessagesWaiting = uxSemaphoreCount - ( UBaseType_t ) 1;
+
+#if ( configUSE_MUTEXES == 1 )
+                {
+                    if ( pxQueue->uxQueueType == queueQUEUE_IS_MUTEX )
+                    {
+                        /* Record the information required to implement
+                        priority inheritance should it become necessary. */
+                        pxQueue->pxMutexHolder = ( int8_t* ) pvTaskIncrementMutexHeldCount();  /*lint !e961 Cast is not redundant as TaskHandle_t is a typedef. */
+                    }
+                    else
+                    {
+                        mtCOVERAGE_TEST_MARKER();
+                    }
+                }
+#endif /* configUSE_MUTEXES */
+
+                /* Check to see if other tasks are blocked waiting to give the
+                semaphore, and if so, unblock the highest priority such task. */
+                if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToSend ) ) == pdFALSE )
+                {
+                    if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToSend ) ) != pdFALSE )
+                    {
+                        queueYIELD_IF_USING_PREEMPTION();
+                    }
+                    else
+                    {
+                        mtCOVERAGE_TEST_MARKER();
+                    }
+                }
+                else
+                {
+                    mtCOVERAGE_TEST_MARKER();
+                }
+
+                taskEXIT_CRITICAL();
+                return pdPASS;
+            }
+            else
+            {
+                if ( xTicksToWait == ( TickType_t ) 0 )
+                {
+                    /* For inheritance to have occurred there must have been an
+                    initial timeout, and an adjusted timeout cannot become 0, as
+                    if it were 0 the function would have exited. */
+#if( configUSE_MUTEXES == 1 )
+                    {
+                        configASSERT( xInheritanceOccurred == pdFALSE );
+                    }
+#endif /* configUSE_MUTEXES */
+
+                    /* The semaphore count was 0 and no block time is specified
+                    (or the block time has expired) so exit now. */
+                    taskEXIT_CRITICAL();
+                    traceQUEUE_RECEIVE_FAILED( pxQueue );
+                    return errQUEUE_EMPTY;
+                }
+                else if ( xEntryTimeSet == pdFALSE )
+                {
+                    /* The semaphore count was 0 and a block time was specified
+                    so configure the timeout structure ready to block. */
+                    vTaskInternalSetTimeOutState( &xTimeOut );
+                    xEntryTimeSet = pdTRUE;
+                }
+                else
+                {
+                    /* Entry time was already set. */
+                    mtCOVERAGE_TEST_MARKER();
+                }
+            }
+        }
+        taskEXIT_CRITICAL();
+
+        /* Interrupts and other tasks can give to and take from the semaphore
+        now the critical section has been exited. */
+
+        vTaskSuspendAll();
+        prvLockQueue( pxQueue );
+
+        /* Update the timeout state to see if it has expired yet. */
+        if ( xTaskCheckForTimeOut( &xTimeOut, &xTicksToWait ) == pdFALSE )
+        {
+            /* A block time is specified and not expired.  If the semaphore
+            count is 0 then enter the Blocked state to wait for a semaphore to
+            become available.  As semaphores are implemented with queues the
+            queue being empty is equivalent to the semaphore count being 0. */
+            if ( prvIsQueueEmpty( pxQueue ) != pdFALSE )
+            {
+                traceBLOCKING_ON_QUEUE_RECEIVE( pxQueue );
+
+#if ( configUSE_MUTEXES == 1 )
+                {
+                    if ( pxQueue->uxQueueType == queueQUEUE_IS_MUTEX )
                     {
-                        if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToReceive ) ) != pdFALSE )
-                        {
-                            /* The task waiting has a higher priority so record that a
-                            context	switch is required. */
-                            if ( pxHigherPriorityTaskWoken != NULL )
-                            {
-                                *pxHigherPriorityTaskWoken = pdTRUE;
-                            }
-                            else
-                            {
-                                mtCOVERAGE_TEST_MARKER();
-                            }
-                        }
-                        else
+                        taskENTER_CRITICAL();
                         {
-                            mtCOVERAGE_TEST_MARKER();
+                            xInheritanceOccurred = xTaskPriorityInherit( ( void* ) pxQueue->pxMutexHolder );
                         }
+                        taskEXIT_CRITICAL();
                     }
                     else
                     {
                         mtCOVERAGE_TEST_MARKER();
                     }
                 }
-#endif /* configUSE_QUEUE_SETS */
+#endif
+
+                vTaskPlaceOnEventList( &( pxQueue->xTasksWaitingToReceive ), xTicksToWait );
+                prvUnlockQueue( pxQueue );
+
+                if ( xTaskResumeAll() == pdFALSE )
+                {
+                    portYIELD_WITHIN_API();
+                }
+                else
+                {
+                    mtCOVERAGE_TEST_MARKER();
+                }
             }
             else
             {
-                /* Increment the lock count so the task that unlocks the queue
-                knows that data was posted while it was locked. */
-                ++( pxQueue->xTxLock );
+                /* There was no timeout and the semaphore count was not 0, so
+                attempt to take the semaphore again. */
+                prvUnlockQueue( pxQueue );
+                ( void ) xTaskResumeAll();
             }
-
-            xReturn = pdPASS;
         }
         else
         {
-            traceQUEUE_SEND_FROM_ISR_FAILED( pxQueue );
-            xReturn = errQUEUE_FULL;
+            /* Timed out. */
+            prvUnlockQueue( pxQueue );
+            ( void ) xTaskResumeAll();
+
+            /* If the semaphore count is 0 exit now as the timeout has
+            expired.  Otherwise return to attempt to take the semaphore that is
+            known to be available.  As semaphores are implemented by queues the
+            queue being empty is equivalent to the semaphore count being 0. */
+            if ( prvIsQueueEmpty( pxQueue ) != pdFALSE )
+            {
+#if ( configUSE_MUTEXES == 1 )
+                {
+                    /* xInheritanceOccurred could only have be set if
+                    pxQueue->uxQueueType == queueQUEUE_IS_MUTEX so no need to
+                    test the mutex type again to check it is actually a mutex. */
+                    if ( xInheritanceOccurred != pdFALSE )
+                    {
+                        taskENTER_CRITICAL();
+                        {
+                            UBaseType_t uxHighestWaitingPriority;
+
+                            /* This task blocking on the mutex caused another
+                            task to inherit this task's priority.  Now this task
+                            has timed out the priority should be disinherited
+                            again, but only as low as the next highest priority
+                            task that is waiting for the same mutex. */
+                            uxHighestWaitingPriority = prvGetDisinheritPriorityAfterTimeout( pxQueue );
+                            vTaskPriorityDisinheritAfterTimeout( ( void* ) pxQueue->pxMutexHolder, uxHighestWaitingPriority );
+                        }
+                        taskEXIT_CRITICAL();
+                    }
+                }
+#endif /* configUSE_MUTEXES */
+
+                traceQUEUE_RECEIVE_FAILED( pxQueue );
+                return errQUEUE_EMPTY;
+            }
+            else
+            {
+                mtCOVERAGE_TEST_MARKER();
+            }
         }
     }
-    portCLEAR_INTERRUPT_MASK_FROM_ISR( uxSavedInterruptStatus );
-    return xReturn;
 }
 /*-----------------------------------------------------------*/
 
-BaseType_t xQueueGenericReceive( QueueHandle_t xQueue, void* const pvBuffer, TickType_t xTicksToWait, const BaseType_t xJustPeeking )
+BaseType_t xQueuePeek( QueueHandle_t xQueue, void* const pvBuffer, TickType_t xTicksToWait )
 {
     BaseType_t xEntryTimeSet = pdFALSE;
     TimeOut_t xTimeOut;
     int8_t* pcOriginalReadPosition;
     Queue_t* const pxQueue = ( Queue_t* ) xQueue;
-    configASSERT( pxQueue );
-    configASSERT( !( ( pvBuffer == NULL ) && ( pxQueue->uxItemSize != ( UBaseType_t ) 0U ) ) );
+
+    /* Check the pointer is not NULL. */
+    configASSERT( ( pxQueue ) );
+
+    /* The buffer into which data is received can only be NULL if the data size
+    is zero (so no data is copied into the buffer. */
+    configASSERT( !( ( ( pvBuffer ) == NULL ) && ( ( pxQueue )->uxItemSize != ( UBaseType_t ) 0U ) ) );
+
+    /* Cannot block if the scheduler is suspended. */
 #if ( ( INCLUDE_xTaskGetSchedulerState == 1 ) || ( configUSE_TIMERS == 1 ) )
     {
         configASSERT( !( ( xTaskGetSchedulerState() == taskSCHEDULER_SUSPENDED ) && ( xTicksToWait != 0 ) ) );
     }
 #endif
 
+
     /* This function relaxes the coding standard somewhat to allow return
     statements within the function itself.  This is done in the interest
     of execution time efficiency. */
@@ -1323,45 +1628,31 @@ BaseType_t xQueueGenericReceive( QueueHandle_t xQueue, void* const pvBuffer, Tic
     {
         taskENTER_CRITICAL();
         {
+            const UBaseType_t uxMessagesWaiting = pxQueue->uxMessagesWaiting;
+
             /* Is there data in the queue now?  To be running the calling task
-            must be	the highest priority task wanting to access the queue. */
-            if ( pxQueue->uxMessagesWaiting > ( UBaseType_t ) 0 )
+            must be the highest priority task wanting to access the queue. */
+            if ( uxMessagesWaiting > ( UBaseType_t ) 0 )
             {
-                /* Remember the read position in case the queue is only being
-                peeked. */
+                /* Remember the read position so it can be reset after the data
+                is read from the queue as this function is only peeking the
+                data, not removing it. */
                 pcOriginalReadPosition = pxQueue->u.pcReadFrom;
+
                 prvCopyDataFromQueue( pxQueue, pvBuffer );
+                traceQUEUE_PEEK( pxQueue );
 
-                if ( xJustPeeking == pdFALSE )
-                {
-                    traceQUEUE_RECEIVE( pxQueue );
-                    /* Actually removing data, not just peeking. */
-                    --( pxQueue->uxMessagesWaiting );
-#if ( configUSE_MUTEXES == 1 )
-                    {
-                        if ( pxQueue->uxQueueType == queueQUEUE_IS_MUTEX )
-                        {
-                            /* Record the information required to implement
-                            priority inheritance should it become necessary. */
-                            pxQueue->pxMutexHolder = ( int8_t* ) pvTaskIncrementMutexHeldCount();  /*lint !e961 Cast is not redundant as TaskHandle_t is a typedef. */
-                        }
-                        else
-                        {
-                            mtCOVERAGE_TEST_MARKER();
-                        }
-                    }
-#endif /* configUSE_MUTEXES */
+                /* The data is not being removed, so reset the read pointer. */
+                pxQueue->u.pcReadFrom = pcOriginalReadPosition;
 
-                    if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToSend ) ) == pdFALSE )
+                /* The data is being left in the queue, so see if there are
+                any other tasks waiting for the data. */
+                if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToReceive ) ) == pdFALSE )
+                {
+                    if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToReceive ) ) != pdFALSE )
                     {
-                        if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToSend ) ) == pdTRUE )
-                        {
-                            queueYIELD_IF_USING_PREEMPTION();
-                        }
-                        else
-                        {
-                            mtCOVERAGE_TEST_MARKER();
-                        }
+                        /* The task waiting has a higher priority than this task. */
+                        queueYIELD_IF_USING_PREEMPTION();
                     }
                     else
                     {
@@ -1370,29 +1661,7 @@ BaseType_t xQueueGenericReceive( QueueHandle_t xQueue, void* const pvBuffer, Tic
                 }
                 else
                 {
-                    traceQUEUE_PEEK( pxQueue );
-                    /* The data is not being removed, so reset the read
-                    pointer. */
-                    pxQueue->u.pcReadFrom = pcOriginalReadPosition;
-
-                    /* The data is being left in the queue, so see if there are
-                    any other tasks waiting for the data. */
-                    if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToReceive ) ) == pdFALSE )
-                    {
-                        if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToReceive ) ) != pdFALSE )
-                        {
-                            /* The task waiting has a higher priority than this task. */
-                            queueYIELD_IF_USING_PREEMPTION();
-                        }
-                        else
-                        {
-                            mtCOVERAGE_TEST_MARKER();
-                        }
-                    }
-                    else
-                    {
-                        mtCOVERAGE_TEST_MARKER();
-                    }
+                    mtCOVERAGE_TEST_MARKER();
                 }
 
                 taskEXIT_CRITICAL();
@@ -1405,14 +1674,15 @@ BaseType_t xQueueGenericReceive( QueueHandle_t xQueue, void* const pvBuffer, Tic
                     /* The queue was empty and no block time is specified (or
                     the block time has expired) so leave now. */
                     taskEXIT_CRITICAL();
-                    traceQUEUE_RECEIVE_FAILED( pxQueue );
+                    traceQUEUE_PEEK_FAILED( pxQueue );
                     return errQUEUE_EMPTY;
                 }
                 else if ( xEntryTimeSet == pdFALSE )
                 {
                     /* The queue was empty and a block time was specified so
-                    configure the timeout structure. */
-                    vTaskSetTimeOutState( &xTimeOut );
+                    configure the timeout structure ready to enter the blocked
+                    state. */
+                    vTaskInternalSetTimeOutState( &xTimeOut );
                     xEntryTimeSet = pdTRUE;
                 }
                 else
@@ -1423,33 +1693,21 @@ BaseType_t xQueueGenericReceive( QueueHandle_t xQueue, void* const pvBuffer, Tic
             }
         }
         taskEXIT_CRITICAL();
+
         /* Interrupts and other tasks can send to and receive from the queue
         now the critical section has been exited. */
+
         vTaskSuspendAll();
         prvLockQueue( pxQueue );
 
         /* Update the timeout state to see if it has expired yet. */
         if ( xTaskCheckForTimeOut( &xTimeOut, &xTicksToWait ) == pdFALSE )
         {
+            /* Timeout has not expired yet, check to see if there is data in the
+            queue now, and if not enter the Blocked state to wait for data. */
             if ( prvIsQueueEmpty( pxQueue ) != pdFALSE )
             {
-                traceBLOCKING_ON_QUEUE_RECEIVE( pxQueue );
-#if ( configUSE_MUTEXES == 1 )
-                {
-                    if ( pxQueue->uxQueueType == queueQUEUE_IS_MUTEX )
-                    {
-                        taskENTER_CRITICAL();
-                        {
-                            vTaskPriorityInherit( ( void* ) pxQueue->pxMutexHolder );
-                        }
-                        taskEXIT_CRITICAL();
-                    }
-                    else
-                    {
-                        mtCOVERAGE_TEST_MARKER();
-                    }
-                }
-#endif
+                traceBLOCKING_ON_QUEUE_PEEK( pxQueue );
                 vTaskPlaceOnEventList( &( pxQueue->xTasksWaitingToReceive ), xTicksToWait );
                 prvUnlockQueue( pxQueue );
 
@@ -1464,17 +1722,28 @@ BaseType_t xQueueGenericReceive( QueueHandle_t xQueue, void* const pvBuffer, Tic
             }
             else
             {
-                /* Try again. */
+                /* There is data in the queue now, so don't enter the blocked
+                state, instead return to try and obtain the data. */
                 prvUnlockQueue( pxQueue );
                 ( void ) xTaskResumeAll();
             }
         }
         else
         {
+            /* The timeout has expired.  If there is still no data in the queue
+            exit, otherwise go back and try to read the data again. */
             prvUnlockQueue( pxQueue );
             ( void ) xTaskResumeAll();
-            traceQUEUE_RECEIVE_FAILED( pxQueue );
-            return errQUEUE_EMPTY;
+
+            if ( prvIsQueueEmpty( pxQueue ) != pdFALSE )
+            {
+                traceQUEUE_PEEK_FAILED( pxQueue );
+                return errQUEUE_EMPTY;
+            }
+            else
+            {
+                mtCOVERAGE_TEST_MARKER();
+            }
         }
     }
 }
@@ -1485,8 +1754,10 @@ BaseType_t xQueueReceiveFromISR( QueueHandle_t xQueue, void* const pvBuffer, Bas
     BaseType_t xReturn;
     UBaseType_t uxSavedInterruptStatus;
     Queue_t* const pxQueue = ( Queue_t* ) xQueue;
+
     configASSERT( pxQueue );
     configASSERT( !( ( pvBuffer == NULL ) && ( pxQueue->uxItemSize != ( UBaseType_t ) 0U ) ) );
+
     /* RTOS ports that support interrupt nesting have the concept of a maximum
     system call (or maximum API call) interrupt priority.  Interrupts that are
     above the maximum system call priority are kept permanently enabled, even
@@ -1502,20 +1773,26 @@ BaseType_t xQueueReceiveFromISR( QueueHandle_t xQueue, void* const pvBuffer, Bas
     More information (albeit Cortex-M specific) is provided on the following
     link: http://www.freertos.org/RTOS-Cortex-M3-M4.html */
     portASSERT_IF_INTERRUPT_PRIORITY_INVALID();
+
     uxSavedInterruptStatus = portSET_INTERRUPT_MASK_FROM_ISR();
     {
+        const UBaseType_t uxMessagesWaiting = pxQueue->uxMessagesWaiting;
+
         /* Cannot block in an ISR, so check there is data available. */
-        if ( pxQueue->uxMessagesWaiting > ( UBaseType_t ) 0 )
+        if ( uxMessagesWaiting > ( UBaseType_t ) 0 )
         {
+            const int8_t cRxLock = pxQueue->cRxLock;
+
             traceQUEUE_RECEIVE_FROM_ISR( pxQueue );
+
             prvCopyDataFromQueue( pxQueue, pvBuffer );
-            --( pxQueue->uxMessagesWaiting );
+            pxQueue->uxMessagesWaiting = uxMessagesWaiting - ( UBaseType_t ) 1;
 
             /* If the queue is locked the event list will not be modified.
             Instead update the lock count so the task that unlocks the queue
             will know that an ISR has removed data while the queue was
             locked. */
-            if ( pxQueue->xRxLock == queueUNLOCKED )
+            if ( cRxLock == queueUNLOCKED )
             {
                 if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToSend ) ) == pdFALSE )
                 {
@@ -1546,7 +1823,7 @@ BaseType_t xQueueReceiveFromISR( QueueHandle_t xQueue, void* const pvBuffer, Bas
             {
                 /* Increment the lock count so the task that unlocks the queue
                 knows that data was removed while it was locked. */
-                ++( pxQueue->xRxLock );
+                pxQueue->cRxLock = ( int8_t ) ( cRxLock + 1 );
             }
 
             xReturn = pdPASS;
@@ -1558,6 +1835,7 @@ BaseType_t xQueueReceiveFromISR( QueueHandle_t xQueue, void* const pvBuffer, Bas
         }
     }
     portCLEAR_INTERRUPT_MASK_FROM_ISR( uxSavedInterruptStatus );
+
     return xReturn;
 }
 /*-----------------------------------------------------------*/
@@ -1568,9 +1846,11 @@ BaseType_t xQueuePeekFromISR( QueueHandle_t xQueue,  void* const pvBuffer )
     UBaseType_t uxSavedInterruptStatus;
     int8_t* pcOriginalReadPosition;
     Queue_t* const pxQueue = ( Queue_t* ) xQueue;
+
     configASSERT( pxQueue );
     configASSERT( !( ( pvBuffer == NULL ) && ( pxQueue->uxItemSize != ( UBaseType_t ) 0U ) ) );
     configASSERT( pxQueue->uxItemSize != 0 ); /* Can't peek a semaphore. */
+
     /* RTOS ports that support interrupt nesting have the concept of a maximum
     system call (or maximum API call) interrupt priority.  Interrupts that are
     above the maximum system call priority are kept permanently enabled, even
@@ -1586,17 +1866,20 @@ BaseType_t xQueuePeekFromISR( QueueHandle_t xQueue,  void* const pvBuffer )
     More information (albeit Cortex-M specific) is provided on the following
     link: http://www.freertos.org/RTOS-Cortex-M3-M4.html */
     portASSERT_IF_INTERRUPT_PRIORITY_INVALID();
+
     uxSavedInterruptStatus = portSET_INTERRUPT_MASK_FROM_ISR();
     {
         /* Cannot block in an ISR, so check there is data available. */
         if ( pxQueue->uxMessagesWaiting > ( UBaseType_t ) 0 )
         {
             traceQUEUE_PEEK_FROM_ISR( pxQueue );
+
             /* Remember the read position so it can be reset as nothing is
             actually being removed from the queue. */
             pcOriginalReadPosition = pxQueue->u.pcReadFrom;
             prvCopyDataFromQueue( pxQueue, pvBuffer );
             pxQueue->u.pcReadFrom = pcOriginalReadPosition;
+
             xReturn = pdPASS;
         }
         else
@@ -1606,6 +1889,7 @@ BaseType_t xQueuePeekFromISR( QueueHandle_t xQueue,  void* const pvBuffer )
         }
     }
     portCLEAR_INTERRUPT_MASK_FROM_ISR( uxSavedInterruptStatus );
+
     return xReturn;
 }
 /*-----------------------------------------------------------*/
@@ -1613,12 +1897,15 @@ BaseType_t xQueuePeekFromISR( QueueHandle_t xQueue,  void* const pvBuffer )
 UBaseType_t uxQueueMessagesWaiting( const QueueHandle_t xQueue )
 {
     UBaseType_t uxReturn;
+
     configASSERT( xQueue );
+
     taskENTER_CRITICAL();
     {
         uxReturn = ( ( Queue_t* ) xQueue )->uxMessagesWaiting;
     }
     taskEXIT_CRITICAL();
+
     return uxReturn;
 } /*lint !e818 Pointer cannot be declared const as xQueue is a typedef not pointer. */
 /*-----------------------------------------------------------*/
@@ -1627,13 +1914,16 @@ UBaseType_t uxQueueSpacesAvailable( const QueueHandle_t xQueue )
 {
     UBaseType_t uxReturn;
     Queue_t* pxQueue;
+
     pxQueue = ( Queue_t* ) xQueue;
     configASSERT( pxQueue );
+
     taskENTER_CRITICAL();
     {
         uxReturn = pxQueue->uxLength - pxQueue->uxMessagesWaiting;
     }
     taskEXIT_CRITICAL();
+
     return uxReturn;
 } /*lint !e818 Pointer cannot be declared const as xQueue is a typedef not pointer. */
 /*-----------------------------------------------------------*/
@@ -1641,8 +1931,11 @@ UBaseType_t uxQueueSpacesAvailable( const QueueHandle_t xQueue )
 UBaseType_t uxQueueMessagesWaitingFromISR( const QueueHandle_t xQueue )
 {
     UBaseType_t uxReturn;
+
     configASSERT( xQueue );
+
     uxReturn = ( ( Queue_t* ) xQueue )->uxMessagesWaiting;
+
     return uxReturn;
 } /*lint !e818 Pointer cannot be declared const as xQueue is a typedef not pointer. */
 /*-----------------------------------------------------------*/
@@ -1650,14 +1943,42 @@ UBaseType_t uxQueueMessagesWaitingFromISR( const QueueHandle_t xQueue )
 void vQueueDelete( QueueHandle_t xQueue )
 {
     Queue_t* const pxQueue = ( Queue_t* ) xQueue;
+
     configASSERT( pxQueue );
     traceQUEUE_DELETE( pxQueue );
+
 #if ( configQUEUE_REGISTRY_SIZE > 0 )
     {
         vQueueUnregisterQueue( pxQueue );
     }
 #endif
-    vPortFree( pxQueue );
+
+#if( ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) && ( configSUPPORT_STATIC_ALLOCATION == 0 ) )
+    {
+        /* The queue can only have been allocated dynamically - free it
+        again. */
+        vPortFree( pxQueue );
+    }
+#elif( ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) && ( configSUPPORT_STATIC_ALLOCATION == 1 ) )
+    {
+        /* The queue could have been allocated statically or dynamically, so
+        check before attempting to free the memory. */
+        if ( pxQueue->ucStaticallyAllocated == ( uint8_t ) pdFALSE )
+        {
+            vPortFree( pxQueue );
+        }
+        else
+        {
+            mtCOVERAGE_TEST_MARKER();
+        }
+    }
+#else
+    {
+        /* The queue must have been statically allocated, so is not going to be
+        deleted.  Avoid compiler warnings about the unused parameter. */
+        ( void ) pxQueue;
+    }
+#endif /* configSUPPORT_DYNAMIC_ALLOCATION */
 }
 /*-----------------------------------------------------------*/
 
@@ -1691,9 +2012,41 @@ uint8_t ucQueueGetQueueType( QueueHandle_t xQueue )
 #endif /* configUSE_TRACE_FACILITY */
 /*-----------------------------------------------------------*/
 
+#if( configUSE_MUTEXES == 1 )
+
+static UBaseType_t prvGetDisinheritPriorityAfterTimeout( const Queue_t* const pxQueue )
+{
+    UBaseType_t uxHighestPriorityOfWaitingTasks;
+
+    /* If a task waiting for a mutex causes the mutex holder to inherit a
+    priority, but the waiting task times out, then the holder should
+    disinherit the priority - but only down to the highest priority of any
+    other tasks that are waiting for the same mutex.  For this purpose,
+    return the priority of the highest priority task that is waiting for the
+    mutex. */
+    if ( listCURRENT_LIST_LENGTH( &( pxQueue->xTasksWaitingToReceive ) ) > 0 )
+    {
+        uxHighestPriorityOfWaitingTasks = configMAX_PRIORITIES - listGET_ITEM_VALUE_OF_HEAD_ENTRY( &( pxQueue->xTasksWaitingToReceive ) );
+    }
+    else
+    {
+        uxHighestPriorityOfWaitingTasks = tskIDLE_PRIORITY;
+    }
+
+    return uxHighestPriorityOfWaitingTasks;
+}
+
+#endif /* configUSE_MUTEXES */
+/*-----------------------------------------------------------*/
+
 static BaseType_t prvCopyDataToQueue( Queue_t* const pxQueue, const void* pvItemToQueue, const BaseType_t xPosition )
 {
     BaseType_t xReturn = pdFALSE;
+    UBaseType_t uxMessagesWaiting;
+
+    /* This function is called from a critical section. */
+
+    uxMessagesWaiting = pxQueue->uxMessagesWaiting;
 
     if ( pxQueue->uxItemSize == ( UBaseType_t ) 0 )
     {
@@ -1742,13 +2095,13 @@ static BaseType_t prvCopyDataToQueue( Queue_t* const pxQueue, const void* pvItem
 
         if ( xPosition == queueOVERWRITE )
         {
-            if ( pxQueue->uxMessagesWaiting > ( UBaseType_t ) 0 )
+            if ( uxMessagesWaiting > ( UBaseType_t ) 0 )
             {
                 /* An item is not being added but overwritten, so subtract
                 one from the recorded number of items in the queue so when
                 one is added again below the number of recorded items remains
                 correct. */
-                --( pxQueue->uxMessagesWaiting );
+                --uxMessagesWaiting;
             }
             else
             {
@@ -1761,7 +2114,8 @@ static BaseType_t prvCopyDataToQueue( Queue_t* const pxQueue, const void* pvItem
         }
     }
 
-    ++( pxQueue->uxMessagesWaiting );
+    pxQueue->uxMessagesWaiting = uxMessagesWaiting + ( UBaseType_t ) 1;
+
     return xReturn;
 }
 /*-----------------------------------------------------------*/
@@ -1789,14 +2143,17 @@ static void prvCopyDataFromQueue( Queue_t* const pxQueue, void* const pvBuffer )
 static void prvUnlockQueue( Queue_t* const pxQueue )
 {
     /* THIS FUNCTION MUST BE CALLED WITH THE SCHEDULER SUSPENDED. */
+
     /* The lock counts contains the number of extra data items placed or
     removed from the queue while the queue was locked.  When a queue is
     locked items can be added or removed, but the event lists cannot be
     updated. */
     taskENTER_CRITICAL();
     {
+        int8_t cTxLock = pxQueue->cTxLock;
+
         /* See if data was added to the queue while it was locked. */
-        while ( pxQueue->xTxLock > queueLOCKED_UNMODIFIED )
+        while ( cTxLock > queueLOCKED_UNMODIFIED )
         {
             /* Data was posted while the queue was locked.  Are any tasks
             blocked waiting for data to become available? */
@@ -1804,7 +2161,7 @@ static void prvUnlockQueue( Queue_t* const pxQueue )
             {
                 if ( pxQueue->pxQueueSetContainer != NULL )
                 {
-                    if ( prvNotifyQueueSetContainer( pxQueue, queueSEND_TO_BACK ) == pdTRUE )
+                    if ( prvNotifyQueueSetContainer( pxQueue, queueSEND_TO_BACK ) != pdFALSE )
                     {
                         /* The queue is a member of a queue set, and posting to
                         the queue set caused a higher priority task to unblock.
@@ -1818,8 +2175,9 @@ static void prvUnlockQueue( Queue_t* const pxQueue )
                 }
                 else
                 {
-                    /* Tasks that are removed from the event list will get added to
-                    the pending ready list as the scheduler is still suspended. */
+                    /* Tasks that are removed from the event list will get
+                    added to the pending ready list as the scheduler is still
+                    suspended. */
                     if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToReceive ) ) == pdFALSE )
                     {
                         if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToReceive ) ) != pdFALSE )
@@ -1847,8 +2205,8 @@ static void prvUnlockQueue( Queue_t* const pxQueue )
                 {
                     if ( xTaskRemoveFromEventList( &( pxQueue->xTasksWaitingToReceive ) ) != pdFALSE )
                     {
-                        /* The task waiting has a higher priority so record that a
-                        context	switch is required. */
+                        /* The task waiting has a higher priority so record that
+                        a context switch is required. */
                         vTaskMissedYield();
                     }
                     else
@@ -1862,16 +2220,20 @@ static void prvUnlockQueue( Queue_t* const pxQueue )
                 }
             }
 #endif /* configUSE_QUEUE_SETS */
-            --( pxQueue->xTxLock );
+
+            --cTxLock;
         }
 
-        pxQueue->xTxLock = queueUNLOCKED;
+        pxQueue->cTxLock = queueUNLOCKED;
     }
     taskEXIT_CRITICAL();
+
     /* Do the same for the Rx lock. */
     taskENTER_CRITICAL();
     {
-        while ( pxQueue->xRxLock > queueLOCKED_UNMODIFIED )
+        int8_t cRxLock = pxQueue->cRxLock;
+
+        while ( cRxLock > queueLOCKED_UNMODIFIED )
         {
             if ( listLIST_IS_EMPTY( &( pxQueue->xTasksWaitingToSend ) ) == pdFALSE )
             {
@@ -1884,7 +2246,7 @@ static void prvUnlockQueue( Queue_t* const pxQueue )
                     mtCOVERAGE_TEST_MARKER();
                 }
 
-                --( pxQueue->xRxLock );
+                --cRxLock;
             }
             else
             {
@@ -1892,7 +2254,7 @@ static void prvUnlockQueue( Queue_t* const pxQueue )
             }
         }
 
-        pxQueue->xRxLock = queueUNLOCKED;
+        pxQueue->cRxLock = queueUNLOCKED;
     }
     taskEXIT_CRITICAL();
 }
@@ -1901,6 +2263,7 @@ static void prvUnlockQueue( Queue_t* const pxQueue )
 static BaseType_t prvIsQueueEmpty( const Queue_t* pxQueue )
 {
     BaseType_t xReturn;
+
     taskENTER_CRITICAL();
     {
         if ( pxQueue->uxMessagesWaiting == ( UBaseType_t )  0 )
@@ -1913,6 +2276,7 @@ static BaseType_t prvIsQueueEmpty( const Queue_t* pxQueue )
         }
     }
     taskEXIT_CRITICAL();
+
     return xReturn;
 }
 /*-----------------------------------------------------------*/
@@ -1920,6 +2284,7 @@ static BaseType_t prvIsQueueEmpty( const Queue_t* pxQueue )
 BaseType_t xQueueIsQueueEmptyFromISR( const QueueHandle_t xQueue )
 {
     BaseType_t xReturn;
+
     configASSERT( xQueue );
 
     if ( ( ( Queue_t* ) xQueue )->uxMessagesWaiting == ( UBaseType_t ) 0 )
@@ -1938,6 +2303,7 @@ BaseType_t xQueueIsQueueEmptyFromISR( const QueueHandle_t xQueue )
 static BaseType_t prvIsQueueFull( const Queue_t* pxQueue )
 {
     BaseType_t xReturn;
+
     taskENTER_CRITICAL();
     {
         if ( pxQueue->uxMessagesWaiting == pxQueue->uxLength )
@@ -1950,6 +2316,7 @@ static BaseType_t prvIsQueueFull( const Queue_t* pxQueue )
         }
     }
     taskEXIT_CRITICAL();
+
     return xReturn;
 }
 /*-----------------------------------------------------------*/
@@ -1957,6 +2324,7 @@ static BaseType_t prvIsQueueFull( const Queue_t* pxQueue )
 BaseType_t xQueueIsQueueFullFromISR( const QueueHandle_t xQueue )
 {
     BaseType_t xReturn;
+
     configASSERT( xQueue );
 
     if ( ( ( Queue_t* ) xQueue )->uxMessagesWaiting == ( ( Queue_t* ) xQueue )->uxLength )
@@ -1978,6 +2346,7 @@ BaseType_t xQueueCRSend( QueueHandle_t xQueue, const void* pvItemToQueue, TickTy
 {
     BaseType_t xReturn;
     Queue_t* const pxQueue = ( Queue_t* ) xQueue;
+
     /* If the queue is already full we may have to block.  A critical section
     is required to prevent an interrupt removing something from the queue
     between the check to see if the queue is full and blocking on the queue. */
@@ -2003,6 +2372,7 @@ BaseType_t xQueueCRSend( QueueHandle_t xQueue, const void* pvItemToQueue, TickTy
         }
     }
     portENABLE_INTERRUPTS();
+
     portDISABLE_INTERRUPTS();
     {
         if ( pxQueue->uxMessagesWaiting < pxQueue->uxLength )
@@ -2040,6 +2410,7 @@ BaseType_t xQueueCRSend( QueueHandle_t xQueue, const void* pvItemToQueue, TickTy
         }
     }
     portENABLE_INTERRUPTS();
+
     return xReturn;
 }
 
@@ -2052,6 +2423,7 @@ BaseType_t xQueueCRReceive( QueueHandle_t xQueue, void* pvBuffer, TickType_t xTi
 {
     BaseType_t xReturn;
     Queue_t* const pxQueue = ( Queue_t* ) xQueue;
+
     /* If the queue is already empty we may have to block.  A critical section
     is required to prevent an interrupt adding something to the queue
     between the check to see if the queue is empty and blocking on the queue. */
@@ -2081,6 +2453,7 @@ BaseType_t xQueueCRReceive( QueueHandle_t xQueue, void* pvBuffer, TickType_t xTi
         }
     }
     portENABLE_INTERRUPTS();
+
     portDISABLE_INTERRUPTS();
     {
         if ( pxQueue->uxMessagesWaiting > ( UBaseType_t ) 0 )
@@ -2099,6 +2472,7 @@ BaseType_t xQueueCRReceive( QueueHandle_t xQueue, void* pvBuffer, TickType_t xTi
 
             --( pxQueue->uxMessagesWaiting );
             ( void ) memcpy( ( void* ) pvBuffer, ( void* ) pxQueue->u.pcReadFrom, ( unsigned ) pxQueue->uxItemSize );
+
             xReturn = pdPASS;
 
             /* Were any co-routines waiting for space to become available? */
@@ -2128,6 +2502,7 @@ BaseType_t xQueueCRReceive( QueueHandle_t xQueue, void* pvBuffer, TickType_t xTi
         }
     }
     portENABLE_INTERRUPTS();
+
     return xReturn;
 }
 
@@ -2259,6 +2634,7 @@ void vQueueAddToRegistry( QueueHandle_t xQueue, const char* pcQueueName ) /*lint
             /* Store the information on this queue. */
             xQueueRegistry[ ux ].pcQueueName = pcQueueName;
             xQueueRegistry[ ux ].xHandle = xQueue;
+
             traceQUEUE_REGISTRY_ADD( xQueue, pcQueueName );
             break;
         }
@@ -2274,6 +2650,34 @@ void vQueueAddToRegistry( QueueHandle_t xQueue, const char* pcQueueName ) /*lint
 
 #if ( configQUEUE_REGISTRY_SIZE > 0 )
 
+const char* pcQueueGetName( QueueHandle_t xQueue ) /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+{
+    UBaseType_t ux;
+    const char* pcReturn = NULL; /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+
+    /* Note there is nothing here to protect against another task adding or
+    removing entries from the registry while it is being searched. */
+    for ( ux = ( UBaseType_t ) 0U; ux < ( UBaseType_t ) configQUEUE_REGISTRY_SIZE; ux++ )
+    {
+        if ( xQueueRegistry[ ux ].xHandle == xQueue )
+        {
+            pcReturn = xQueueRegistry[ ux ].pcQueueName;
+            break;
+        }
+        else
+        {
+            mtCOVERAGE_TEST_MARKER();
+        }
+    }
+
+    return pcReturn;
+} /*lint !e818 xQueue cannot be a pointer to const because it is a typedef. */
+
+#endif /* configQUEUE_REGISTRY_SIZE */
+/*-----------------------------------------------------------*/
+
+#if ( configQUEUE_REGISTRY_SIZE > 0 )
+
 void vQueueUnregisterQueue( QueueHandle_t xQueue )
 {
     UBaseType_t ux;
@@ -2286,6 +2690,11 @@ void vQueueUnregisterQueue( QueueHandle_t xQueue )
         {
             /* Set the name to NULL to show that this slot if free again. */
             xQueueRegistry[ ux ].pcQueueName = NULL;
+
+            /* Set the handle to NULL to ensure the same queue handle cannot
+            appear in the registry twice if it is added, removed, then
+            added again. */
+            xQueueRegistry[ ux ].xHandle = ( QueueHandle_t ) 0;
             break;
         }
         else
@@ -2293,6 +2702,7 @@ void vQueueUnregisterQueue( QueueHandle_t xQueue )
             mtCOVERAGE_TEST_MARKER();
         }
     }
+
 } /*lint !e818 xQueue could not be pointer to const because it is a typedef. */
 
 #endif /* configQUEUE_REGISTRY_SIZE */
@@ -2303,6 +2713,7 @@ void vQueueUnregisterQueue( QueueHandle_t xQueue )
 void vQueueWaitForMessageRestricted( QueueHandle_t xQueue, TickType_t xTicksToWait, const BaseType_t xWaitIndefinitely )
 {
     Queue_t* const pxQueue = ( Queue_t* ) xQueue;
+
     /* This function should not be called by application code hence the
     'Restricted' in its name.  It is not part of the public API.  It is
     designed for use by kernel code, and has special calling requirements.
@@ -2310,6 +2721,7 @@ void vQueueWaitForMessageRestricted( QueueHandle_t xQueue, TickType_t xTicksToWa
     possibly ever have one item in it, so the list will be fast, but even
     so it should be called with the scheduler locked and not from a critical
     section. */
+
     /* Only do anything if there are no messages in the queue.  This function
     will not actually cause the task to block, just place it on a blocked
     list.  It will not block until the scheduler is unlocked - at which
@@ -2334,12 +2746,14 @@ void vQueueWaitForMessageRestricted( QueueHandle_t xQueue, TickType_t xTicksToWa
 #endif /* configUSE_TIMERS */
 /*-----------------------------------------------------------*/
 
-#if ( configUSE_QUEUE_SETS == 1 )
+#if( ( configUSE_QUEUE_SETS == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) )
 
 QueueSetHandle_t xQueueCreateSet( const UBaseType_t uxEventQueueLength )
 {
     QueueSetHandle_t pxQueue;
-    pxQueue = xQueueGenericCreate( uxEventQueueLength, sizeof( Queue_t* ), queueQUEUE_TYPE_SET );
+
+    pxQueue = xQueueGenericCreate( uxEventQueueLength, ( UBaseType_t ) sizeof( Queue_t* ), queueQUEUE_TYPE_SET );
+
     return pxQueue;
 }
 
@@ -2351,6 +2765,7 @@ QueueSetHandle_t xQueueCreateSet( const UBaseType_t uxEventQueueLength )
 BaseType_t xQueueAddToSet( QueueSetMemberHandle_t xQueueOrSemaphore, QueueSetHandle_t xQueueSet )
 {
     BaseType_t xReturn;
+
     taskENTER_CRITICAL();
     {
         if ( ( ( Queue_t* ) xQueueOrSemaphore )->pxQueueSetContainer != NULL )
@@ -2371,6 +2786,7 @@ BaseType_t xQueueAddToSet( QueueSetMemberHandle_t xQueueOrSemaphore, QueueSetHan
         }
     }
     taskEXIT_CRITICAL();
+
     return xReturn;
 }
 
@@ -2418,7 +2834,8 @@ BaseType_t xQueueRemoveFromSet( QueueSetMemberHandle_t xQueueOrSemaphore, QueueS
 QueueSetMemberHandle_t xQueueSelectFromSet( QueueSetHandle_t xQueueSet, TickType_t const xTicksToWait )
 {
     QueueSetMemberHandle_t xReturn = NULL;
-    ( void ) xQueueGenericReceive( ( QueueHandle_t ) xQueueSet, &xReturn, xTicksToWait, pdFALSE ); /*lint !e961 Casting from one typedef to another is not redundant. */
+
+    ( void ) xQueueReceive( ( QueueHandle_t ) xQueueSet, &xReturn, xTicksToWait ); /*lint !e961 Casting from one typedef to another is not redundant. */
     return xReturn;
 }
 
@@ -2430,6 +2847,7 @@ QueueSetMemberHandle_t xQueueSelectFromSet( QueueSetHandle_t xQueueSet, TickType
 QueueSetMemberHandle_t xQueueSelectFromSetFromISR( QueueSetHandle_t xQueueSet )
 {
     QueueSetMemberHandle_t xReturn = NULL;
+
     ( void ) xQueueReceiveFromISR( ( QueueHandle_t ) xQueueSet, &xReturn, NULL ); /*lint !e961 Casting from one typedef to another is not redundant. */
     return xReturn;
 }
@@ -2443,17 +2861,22 @@ static BaseType_t prvNotifyQueueSetContainer( const Queue_t* const pxQueue, cons
 {
     Queue_t* pxQueueSetContainer = pxQueue->pxQueueSetContainer;
     BaseType_t xReturn = pdFALSE;
+
     /* This function must be called form a critical section. */
+
     configASSERT( pxQueueSetContainer );
     configASSERT( pxQueueSetContainer->uxMessagesWaiting < pxQueueSetContainer->uxLength );
 
     if ( pxQueueSetContainer->uxMessagesWaiting < pxQueueSetContainer->uxLength )
     {
+        const int8_t cTxLock = pxQueueSetContainer->cTxLock;
+
         traceQUEUE_SEND( pxQueueSetContainer );
+
         /* The data copied is the handle of the queue that contains data. */
         xReturn = prvCopyDataToQueue( pxQueueSetContainer, &pxQueue, xCopyPosition );
 
-        if ( pxQueueSetContainer->xTxLock == queueUNLOCKED )
+        if ( cTxLock == queueUNLOCKED )
         {
             if ( listLIST_IS_EMPTY( &( pxQueueSetContainer->xTasksWaitingToReceive ) ) == pdFALSE )
             {
@@ -2474,7 +2897,7 @@ static BaseType_t prvNotifyQueueSetContainer( const Queue_t* const pxQueue, cons
         }
         else
         {
-            ( pxQueueSetContainer->xTxLock )++;
+            pxQueueSetContainer->cTxLock = ( int8_t ) ( cTxLock + 1 );
         }
     }
     else
diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/stream_buffer.c b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/stream_buffer.c
new file mode 100644
index 00000000..4a0725e3
--- /dev/null
+++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/stream_buffer.c
@@ -0,0 +1,1204 @@
+/*
+ * FreeRTOS Kernel V10.0.1
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
+
+/* Standard includes. */
+#include 
+#include 
+
+/* Defining MPU_WRAPPERS_INCLUDED_FROM_API_FILE prevents task.h from redefining
+all the API functions to use the MPU wrappers.  That should only be done when
+task.h is included from an application file. */
+#define MPU_WRAPPERS_INCLUDED_FROM_API_FILE
+
+/* FreeRTOS includes. */
+#include "FreeRTOS.h"
+#include "task.h"
+#include "stream_buffer.h"
+
+#if( configUSE_TASK_NOTIFICATIONS != 1 )
+#error configUSE_TASK_NOTIFICATIONS must be set to 1 to build stream_buffer.c
+#endif
+
+/* Lint e961 and e750 are suppressed as a MISRA exception justified because the
+MPU ports require MPU_WRAPPERS_INCLUDED_FROM_API_FILE to be defined for the
+header files above, but not in this file, in order to generate the correct
+privileged Vs unprivileged linkage and placement. */
+#undef MPU_WRAPPERS_INCLUDED_FROM_API_FILE /*lint !e961 !e750. */
+
+/* If the user has not provided application specific Rx notification macros,
+or #defined the notification macros away, them provide default implementations
+that uses task notifications. */
+/*lint -save -e9026 Function like macros allowed and needed here so they can be overidden. */
+#ifndef sbRECEIVE_COMPLETED
+#define sbRECEIVE_COMPLETED( pxStreamBuffer )										\
+		vTaskSuspendAll();																\
+		{																				\
+			if( ( pxStreamBuffer )->xTaskWaitingToSend != NULL )						\
+			{																			\
+				( void ) xTaskNotify( ( pxStreamBuffer )->xTaskWaitingToSend,			\
+									  ( uint32_t ) 0,									\
+									  eNoAction );										\
+				( pxStreamBuffer )->xTaskWaitingToSend = NULL;							\
+			}																			\
+		}																				\
+		( void ) xTaskResumeAll();
+#endif /* sbRECEIVE_COMPLETED */
+
+#ifndef sbRECEIVE_COMPLETED_FROM_ISR
+#define sbRECEIVE_COMPLETED_FROM_ISR( pxStreamBuffer,								\
+										  pxHigherPriorityTaskWoken )					\
+	{																					\
+	UBaseType_t uxSavedInterruptStatus;													\
+																						\
+		uxSavedInterruptStatus = ( UBaseType_t ) portSET_INTERRUPT_MASK_FROM_ISR();		\
+		{																				\
+			if( ( pxStreamBuffer )->xTaskWaitingToSend != NULL )						\
+			{																			\
+				( void ) xTaskNotifyFromISR( ( pxStreamBuffer )->xTaskWaitingToSend,	\
+											 ( uint32_t ) 0,							\
+											 eNoAction,									\
+											 pxHigherPriorityTaskWoken );				\
+				( pxStreamBuffer )->xTaskWaitingToSend = NULL;							\
+			}																			\
+		}																				\
+		portCLEAR_INTERRUPT_MASK_FROM_ISR( uxSavedInterruptStatus );					\
+	}
+#endif /* sbRECEIVE_COMPLETED_FROM_ISR */
+
+/* If the user has not provided an application specific Tx notification macro,
+or #defined the notification macro away, them provide a default implementation
+that uses task notifications. */
+#ifndef sbSEND_COMPLETED
+#define sbSEND_COMPLETED( pxStreamBuffer )											\
+		vTaskSuspendAll();																\
+		{																				\
+			if( ( pxStreamBuffer )->xTaskWaitingToReceive != NULL )						\
+			{																			\
+				( void ) xTaskNotify( ( pxStreamBuffer )->xTaskWaitingToReceive,		\
+									  ( uint32_t ) 0,									\
+									  eNoAction );										\
+				( pxStreamBuffer )->xTaskWaitingToReceive = NULL;						\
+			}																			\
+		}																				\
+		( void ) xTaskResumeAll();
+#endif /* sbSEND_COMPLETED */
+
+#ifndef sbSEND_COMPLETE_FROM_ISR
+#define sbSEND_COMPLETE_FROM_ISR( pxStreamBuffer, pxHigherPriorityTaskWoken )		\
+	{																					\
+	UBaseType_t uxSavedInterruptStatus;													\
+																						\
+		uxSavedInterruptStatus = ( UBaseType_t ) portSET_INTERRUPT_MASK_FROM_ISR();		\
+		{																				\
+			if( ( pxStreamBuffer )->xTaskWaitingToReceive != NULL )						\
+			{																			\
+				( void ) xTaskNotifyFromISR( ( pxStreamBuffer )->xTaskWaitingToReceive,	\
+											 ( uint32_t ) 0,							\
+											 eNoAction,									\
+											 pxHigherPriorityTaskWoken );				\
+				( pxStreamBuffer )->xTaskWaitingToReceive = NULL;						\
+			}																			\
+		}																				\
+		portCLEAR_INTERRUPT_MASK_FROM_ISR( uxSavedInterruptStatus );					\
+	}
+#endif /* sbSEND_COMPLETE_FROM_ISR */
+/*lint -restore (9026) */
+
+/* The number of bytes used to hold the length of a message in the buffer. */
+#define sbBYTES_TO_STORE_MESSAGE_LENGTH ( sizeof( size_t ) )
+
+/* Bits stored in the ucFlags field of the stream buffer. */
+#define sbFLAGS_IS_MESSAGE_BUFFER		( ( uint8_t ) 1 ) /* Set if the stream buffer was created as a message buffer, in which case it holds discrete messages rather than a stream. */
+#define sbFLAGS_IS_STATICALLY_ALLOCATED ( ( uint8_t ) 2 ) /* Set if the stream buffer was created using statically allocated memory. */
+
+/*-----------------------------------------------------------*/
+
+/* Structure that hold state information on the buffer. */
+typedef struct xSTREAM_BUFFER /*lint !e9058 Style convention uses tag. */
+{
+    volatile size_t xTail;				/* Index to the next item to read within the buffer. */
+    volatile size_t xHead;				/* Index to the next item to write within the buffer. */
+    size_t xLength;						/* The length of the buffer pointed to by pucBuffer. */
+    size_t xTriggerLevelBytes;			/* The number of bytes that must be in the stream buffer before a task that is waiting for data is unblocked. */
+    volatile TaskHandle_t xTaskWaitingToReceive; /* Holds the handle of a task waiting for data, or NULL if no tasks are waiting. */
+    volatile TaskHandle_t xTaskWaitingToSend;	/* Holds the handle of a task waiting to send data to a message buffer that is full. */
+    uint8_t* pucBuffer;					/* Points to the buffer itself - that is - the RAM that stores the data passed through the buffer. */
+    uint8_t ucFlags;
+
+#if ( configUSE_TRACE_FACILITY == 1 )
+    UBaseType_t uxStreamBufferNumber;		/* Used for tracing purposes. */
+#endif
+} StreamBuffer_t;
+
+/*
+ * The number of bytes available to be read from the buffer.
+ */
+static size_t prvBytesInBuffer( const StreamBuffer_t* const pxStreamBuffer ) PRIVILEGED_FUNCTION;
+
+/*
+ * Add xCount bytes from pucData into the pxStreamBuffer message buffer.
+ * Returns the number of bytes written, which will either equal xCount in the
+ * success case, or 0 if there was not enough space in the buffer (in which case
+ * no data is written into the buffer).
+ */
+static size_t prvWriteBytesToBuffer( StreamBuffer_t* const pxStreamBuffer, const uint8_t* pucData, size_t xCount ) PRIVILEGED_FUNCTION;
+
+/*
+ * If the stream buffer is being used as a message buffer, then reads an entire
+ * message out of the buffer.  If the stream buffer is being used as a stream
+ * buffer then read as many bytes as possible from the buffer.
+ * prvReadBytesFromBuffer() is called to actually extract the bytes from the
+ * buffer's data storage area.
+ */
+static size_t prvReadMessageFromBuffer( StreamBuffer_t* pxStreamBuffer,
+                                        void* pvRxData,
+                                        size_t xBufferLengthBytes,
+                                        size_t xBytesAvailable,
+                                        size_t xBytesToStoreMessageLength ) PRIVILEGED_FUNCTION;
+
+/*
+ * If the stream buffer is being used as a message buffer, then writes an entire
+ * message to the buffer.  If the stream buffer is being used as a stream
+ * buffer then write as many bytes as possible to the buffer.
+ * prvWriteBytestoBuffer() is called to actually send the bytes to the buffer's
+ * data storage area.
+ */
+static size_t prvWriteMessageToBuffer(  StreamBuffer_t* const pxStreamBuffer,
+                                        const void* pvTxData,
+                                        size_t xDataLengthBytes,
+                                        size_t xSpace,
+                                        size_t xRequiredSpace ) PRIVILEGED_FUNCTION;
+
+/*
+ * Read xMaxCount bytes from the pxStreamBuffer message buffer and write them
+ * to pucData.
+ */
+static size_t prvReadBytesFromBuffer( StreamBuffer_t* pxStreamBuffer,
+                                      uint8_t* pucData,
+                                      size_t xMaxCount,
+                                      size_t xBytesAvailable );
+PRIVILEGED_FUNCTION
+
+/*
+ * Called by both pxStreamBufferCreate() and pxStreamBufferCreateStatic() to
+ * initialise the members of the newly created stream buffer structure.
+ */
+static void prvInitialiseNewStreamBuffer( StreamBuffer_t* const pxStreamBuffer,
+        uint8_t* const pucBuffer,
+        size_t xBufferSizeBytes,
+        size_t xTriggerLevelBytes,
+        BaseType_t xIsMessageBuffer ) PRIVILEGED_FUNCTION;
+
+/*-----------------------------------------------------------*/
+
+#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 )
+
+StreamBufferHandle_t xStreamBufferGenericCreate( size_t xBufferSizeBytes, size_t xTriggerLevelBytes, BaseType_t xIsMessageBuffer )
+{
+    uint8_t* pucAllocatedMemory;
+
+    /* In case the stream buffer is going to be used as a message buffer
+    (that is, it will hold discrete messages with a little meta data that
+    says how big the next message is) check the buffer will be large enough
+    to hold at least one message. */
+    configASSERT( xBufferSizeBytes > sbBYTES_TO_STORE_MESSAGE_LENGTH );
+    configASSERT( xTriggerLevelBytes <= xBufferSizeBytes );
+
+    /* A trigger level of 0 would cause a waiting task to unblock even when
+    the buffer was empty. */
+    if ( xTriggerLevelBytes == ( size_t ) 0 )
+    {
+        xTriggerLevelBytes = ( size_t ) 1; /*lint !e9044 Parameter modified to ensure it doesn't have a dangerous value. */
+    }
+
+    /* A stream buffer requires a StreamBuffer_t structure and a buffer.
+    Both are allocated in a single call to pvPortMalloc().  The
+    StreamBuffer_t structure is placed at the start of the allocated memory
+    and the buffer follows immediately after.  The requested size is
+    incremented so the free space is returned as the user would expect -
+    this is a quirk of the implementation that means otherwise the free
+    space would be reported as one byte smaller than would be logically
+    expected. */
+    xBufferSizeBytes++;
+    pucAllocatedMemory = ( uint8_t* ) pvPortMalloc( xBufferSizeBytes + sizeof( StreamBuffer_t ) );  /*lint !e9079 malloc() only returns void*. */
+
+    if ( pucAllocatedMemory != NULL )
+    {
+        prvInitialiseNewStreamBuffer( ( StreamBuffer_t* ) pucAllocatedMemory, /* Structure at the start of the allocated memory. */ /*lint !e9087 Safe cast as allocated memory is aligned. */  /*lint !e826 Area is not too small and alignment is guaranteed provided malloc() behaves as expected and returns aligned buffer. */
+                                      pucAllocatedMemory + sizeof( StreamBuffer_t ),  /* Storage area follows. */ /*lint !e9016 Indexing past structure valid for uint8_t pointer, also storage area has no alignment requirement. */
+                                      xBufferSizeBytes,
+                                      xTriggerLevelBytes,
+                                      xIsMessageBuffer );
+
+        traceSTREAM_BUFFER_CREATE( ( ( StreamBuffer_t* ) pucAllocatedMemory ), xIsMessageBuffer );
+    }
+    else
+    {
+        traceSTREAM_BUFFER_CREATE_FAILED( xIsMessageBuffer );
+    }
+
+    return ( StreamBufferHandle_t* ) pucAllocatedMemory;  /*lint !e9087 !e826 Safe cast as allocated memory is aligned. */
+}
+
+#endif /* configSUPPORT_DYNAMIC_ALLOCATION */
+/*-----------------------------------------------------------*/
+
+#if( configSUPPORT_STATIC_ALLOCATION == 1 )
+
+StreamBufferHandle_t xStreamBufferGenericCreateStatic( size_t xBufferSizeBytes,
+        size_t xTriggerLevelBytes,
+        BaseType_t xIsMessageBuffer,
+        uint8_t* const pucStreamBufferStorageArea,
+        StaticStreamBuffer_t* const pxStaticStreamBuffer )
+{
+    StreamBuffer_t* const pxStreamBuffer = ( StreamBuffer_t* ) pxStaticStreamBuffer;   /*lint !e740 !e9087 Safe cast as StaticStreamBuffer_t is opaque Streambuffer_t. */
+    StreamBufferHandle_t xReturn;
+
+    configASSERT( pucStreamBufferStorageArea );
+    configASSERT( pxStaticStreamBuffer );
+    configASSERT( xTriggerLevelBytes <= xBufferSizeBytes );
+
+    /* A trigger level of 0 would cause a waiting task to unblock even when
+    the buffer was empty. */
+    if ( xTriggerLevelBytes == ( size_t ) 0 )
+    {
+        xTriggerLevelBytes = ( size_t ) 1; /*lint !e9044 Function parameter deliberately modified to ensure it is in range. */
+    }
+
+    /* In case the stream buffer is going to be used as a message buffer
+    (that is, it will hold discrete messages with a little meta data that
+    says how big the next message is) check the buffer will be large enough
+    to hold at least one message. */
+    configASSERT( xBufferSizeBytes > sbBYTES_TO_STORE_MESSAGE_LENGTH );
+
+#if( configASSERT_DEFINED == 1 )
+    {
+        /* Sanity check that the size of the structure used to declare a
+        variable of type StaticStreamBuffer_t equals the size of the real
+        message buffer structure. */
+        volatile size_t xSize = sizeof( StaticStreamBuffer_t );
+        configASSERT( xSize == sizeof( StreamBuffer_t ) );
+    }
+#endif /* configASSERT_DEFINED */
+
+    if ( ( pucStreamBufferStorageArea != NULL ) && ( pxStaticStreamBuffer != NULL ) )
+    {
+        prvInitialiseNewStreamBuffer( pxStreamBuffer,
+                                      pucStreamBufferStorageArea,
+                                      xBufferSizeBytes,
+                                      xTriggerLevelBytes,
+                                      xIsMessageBuffer );
+
+        /* Remember this was statically allocated in case it is ever deleted
+        again. */
+        pxStreamBuffer->ucFlags |= sbFLAGS_IS_STATICALLY_ALLOCATED;
+
+        traceSTREAM_BUFFER_CREATE( pxStreamBuffer, xIsMessageBuffer );
+
+        xReturn = ( StreamBufferHandle_t ) pxStaticStreamBuffer; /*lint !e9087 Data hiding requires cast to opaque type. */
+    }
+    else
+    {
+        xReturn = NULL;
+        traceSTREAM_BUFFER_CREATE_STATIC_FAILED( xReturn, xIsMessageBuffer );
+    }
+
+    return xReturn;
+}
+
+#endif /* ( configSUPPORT_STATIC_ALLOCATION == 1 ) */
+/*-----------------------------------------------------------*/
+
+void vStreamBufferDelete( StreamBufferHandle_t xStreamBuffer )
+{
+    StreamBuffer_t* pxStreamBuffer = ( StreamBuffer_t* ) xStreamBuffer;   /*lint !e9087 !e9079 Safe cast as StreamBufferHandle_t is opaque Streambuffer_t. */
+
+    configASSERT( pxStreamBuffer );
+
+    traceSTREAM_BUFFER_DELETE( xStreamBuffer );
+
+    if ( ( pxStreamBuffer->ucFlags & sbFLAGS_IS_STATICALLY_ALLOCATED ) == ( uint8_t ) pdFALSE )
+    {
+#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 )
+        {
+            /* Both the structure and the buffer were allocated using a single call
+            to pvPortMalloc(), hence only one call to vPortFree() is required. */
+            vPortFree( ( void* ) pxStreamBuffer );  /*lint !e9087 Standard free() semantics require void *, plus pxStreamBuffer was allocated by pvPortMalloc(). */
+        }
+#else
+        {
+            /* Should not be possible to get here, ucFlags must be corrupt.
+            Force an assert. */
+            configASSERT( xStreamBuffer == ( StreamBufferHandle_t ) ~0 );
+        }
+#endif
+    }
+    else
+    {
+        /* The structure and buffer were not allocated dynamically and cannot be
+        freed - just scrub the structure so future use will assert. */
+        memset( pxStreamBuffer, 0x00, sizeof( StreamBuffer_t ) );
+    }
+}
+/*-----------------------------------------------------------*/
+
+BaseType_t xStreamBufferReset( StreamBufferHandle_t xStreamBuffer )
+{
+    StreamBuffer_t* const pxStreamBuffer = ( StreamBuffer_t* ) xStreamBuffer;   /*lint !e9087 !e9079 Safe cast as StreamBufferHandle_t is opaque Streambuffer_t. */
+    BaseType_t xReturn = pdFAIL, xIsMessageBuffer;
+
+#if( configUSE_TRACE_FACILITY == 1 )
+    UBaseType_t uxStreamBufferNumber;
+#endif
+
+    configASSERT( pxStreamBuffer );
+
+#if( configUSE_TRACE_FACILITY == 1 )
+    {
+        /* Store the stream buffer number so it can be restored after the
+        reset. */
+        uxStreamBufferNumber = pxStreamBuffer->uxStreamBufferNumber;
+    }
+#endif
+
+    /* Can only reset a message buffer if there are no tasks blocked on it. */
+    if ( pxStreamBuffer->xTaskWaitingToReceive == NULL )
+    {
+        if ( pxStreamBuffer->xTaskWaitingToSend == NULL )
+        {
+            if ( ( pxStreamBuffer->ucFlags & sbFLAGS_IS_MESSAGE_BUFFER ) != ( uint8_t ) 0 )
+            {
+                xIsMessageBuffer = pdTRUE;
+            }
+            else
+            {
+                xIsMessageBuffer = pdFALSE;
+            }
+
+            prvInitialiseNewStreamBuffer( pxStreamBuffer,
+                                          pxStreamBuffer->pucBuffer,
+                                          pxStreamBuffer->xLength,
+                                          pxStreamBuffer->xTriggerLevelBytes,
+                                          xIsMessageBuffer );
+            xReturn = pdPASS;
+
+#if( configUSE_TRACE_FACILITY == 1 )
+            {
+                pxStreamBuffer->uxStreamBufferNumber = uxStreamBufferNumber;
+            }
+#endif
+
+            traceSTREAM_BUFFER_RESET( xStreamBuffer );
+        }
+    }
+
+    return xReturn;
+}
+/*-----------------------------------------------------------*/
+
+BaseType_t xStreamBufferSetTriggerLevel( StreamBufferHandle_t xStreamBuffer, size_t xTriggerLevel )
+{
+    StreamBuffer_t* const pxStreamBuffer = ( StreamBuffer_t* ) xStreamBuffer;   /*lint !e9087 !e9079 Safe cast as StreamBufferHandle_t is opaque Streambuffer_t. */
+    BaseType_t xReturn;
+
+    configASSERT( pxStreamBuffer );
+
+    /* It is not valid for the trigger level to be 0. */
+    if ( xTriggerLevel == ( size_t ) 0 )
+    {
+        xTriggerLevel = ( size_t ) 1; /*lint !e9044 Parameter modified to ensure it doesn't have a dangerous value. */
+    }
+
+    /* The trigger level is the number of bytes that must be in the stream
+    buffer before a task that is waiting for data is unblocked. */
+    if ( xTriggerLevel <= pxStreamBuffer->xLength )
+    {
+        pxStreamBuffer->xTriggerLevelBytes = xTriggerLevel;
+        xReturn = pdPASS;
+    }
+    else
+    {
+        xReturn = pdFALSE;
+    }
+
+    return xReturn;
+}
+/*-----------------------------------------------------------*/
+
+size_t xStreamBufferSpacesAvailable( StreamBufferHandle_t xStreamBuffer )
+{
+    const StreamBuffer_t* const pxStreamBuffer = ( StreamBuffer_t* ) xStreamBuffer;   /*lint !e9087 !e9079 Safe cast as StreamBufferHandle_t is opaque Streambuffer_t. */
+    size_t xSpace;
+
+    configASSERT( pxStreamBuffer );
+
+    xSpace = pxStreamBuffer->xLength + pxStreamBuffer->xTail;
+    xSpace -= pxStreamBuffer->xHead;
+    xSpace -= ( size_t ) 1;
+
+    if ( xSpace >= pxStreamBuffer->xLength )
+    {
+        xSpace -= pxStreamBuffer->xLength;
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+
+    return xSpace;
+}
+/*-----------------------------------------------------------*/
+
+size_t xStreamBufferBytesAvailable( StreamBufferHandle_t xStreamBuffer )
+{
+    const StreamBuffer_t* const pxStreamBuffer = ( StreamBuffer_t* ) xStreamBuffer;   /*lint !e9087 !e9079 Safe cast as StreamBufferHandle_t is opaque Streambuffer_t. */
+    size_t xReturn;
+
+    configASSERT( pxStreamBuffer );
+
+    xReturn = prvBytesInBuffer( pxStreamBuffer );
+    return xReturn;
+}
+/*-----------------------------------------------------------*/
+
+size_t xStreamBufferSend( StreamBufferHandle_t xStreamBuffer,
+                          const void* pvTxData,
+                          size_t xDataLengthBytes,
+                          TickType_t xTicksToWait )
+{
+    StreamBuffer_t* const pxStreamBuffer = ( StreamBuffer_t* ) xStreamBuffer;   /*lint !e9087 !e9079 Safe cast as StreamBufferHandle_t is opaque Streambuffer_t. */
+    size_t xReturn, xSpace = 0;
+    size_t xRequiredSpace = xDataLengthBytes;
+    TimeOut_t xTimeOut;
+
+    configASSERT( pvTxData );
+    configASSERT( pxStreamBuffer );
+
+    /* This send function is used to write to both message buffers and stream
+    buffers.  If this is a message buffer then the space needed must be
+    increased by the amount of bytes needed to store the length of the
+    message. */
+    if ( ( pxStreamBuffer->ucFlags & sbFLAGS_IS_MESSAGE_BUFFER ) != ( uint8_t ) 0 )
+    {
+        xRequiredSpace += sbBYTES_TO_STORE_MESSAGE_LENGTH;
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+
+    if ( xTicksToWait != ( TickType_t ) 0 )
+    {
+        vTaskSetTimeOutState( &xTimeOut );
+
+        do
+        {
+            /* Wait until the required number of bytes are free in the message
+            buffer. */
+            taskENTER_CRITICAL();
+            {
+                xSpace = xStreamBufferSpacesAvailable( pxStreamBuffer );
+
+                if ( xSpace < xRequiredSpace )
+                {
+                    /* Clear notification state as going to wait for space. */
+                    ( void ) xTaskNotifyStateClear( NULL );
+
+                    /* Should only be one writer. */
+                    configASSERT( pxStreamBuffer->xTaskWaitingToSend == NULL );
+                    pxStreamBuffer->xTaskWaitingToSend = xTaskGetCurrentTaskHandle();
+                }
+                else
+                {
+                    taskEXIT_CRITICAL();
+                    break;
+                }
+            }
+            taskEXIT_CRITICAL();
+
+            traceBLOCKING_ON_STREAM_BUFFER_SEND( xStreamBuffer );
+            ( void ) xTaskNotifyWait( ( uint32_t ) 0, UINT32_MAX, NULL, xTicksToWait );
+            pxStreamBuffer->xTaskWaitingToSend = NULL;
+
+        }
+        while ( xTaskCheckForTimeOut( &xTimeOut, &xTicksToWait ) == pdFALSE );
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+
+    if ( xSpace == ( size_t ) 0 )
+    {
+        xSpace = xStreamBufferSpacesAvailable( pxStreamBuffer );
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+
+    xReturn = prvWriteMessageToBuffer( pxStreamBuffer, pvTxData, xDataLengthBytes, xSpace, xRequiredSpace );
+
+    if ( xReturn > ( size_t ) 0 )
+    {
+        traceSTREAM_BUFFER_SEND( xStreamBuffer, xReturn );
+
+        /* Was a task waiting for the data? */
+        if ( prvBytesInBuffer( pxStreamBuffer ) >= pxStreamBuffer->xTriggerLevelBytes )
+        {
+            sbSEND_COMPLETED( pxStreamBuffer );
+        }
+        else
+        {
+            mtCOVERAGE_TEST_MARKER();
+        }
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+        traceSTREAM_BUFFER_SEND_FAILED( xStreamBuffer );
+    }
+
+    return xReturn;
+}
+/*-----------------------------------------------------------*/
+
+size_t xStreamBufferSendFromISR( StreamBufferHandle_t xStreamBuffer,
+                                 const void* pvTxData,
+                                 size_t xDataLengthBytes,
+                                 BaseType_t* const pxHigherPriorityTaskWoken )
+{
+    StreamBuffer_t* const pxStreamBuffer = ( StreamBuffer_t* ) xStreamBuffer;   /*lint !e9087 !e9079 Safe cast as StreamBufferHandle_t is opaque Streambuffer_t. */
+    size_t xReturn, xSpace;
+    size_t xRequiredSpace = xDataLengthBytes;
+
+    configASSERT( pvTxData );
+    configASSERT( pxStreamBuffer );
+
+    /* This send function is used to write to both message buffers and stream
+    buffers.  If this is a message buffer then the space needed must be
+    increased by the amount of bytes needed to store the length of the
+    message. */
+    if ( ( pxStreamBuffer->ucFlags & sbFLAGS_IS_MESSAGE_BUFFER ) != ( uint8_t ) 0 )
+    {
+        xRequiredSpace += sbBYTES_TO_STORE_MESSAGE_LENGTH;
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+
+    xSpace = xStreamBufferSpacesAvailable( pxStreamBuffer );
+    xReturn = prvWriteMessageToBuffer( pxStreamBuffer, pvTxData, xDataLengthBytes, xSpace, xRequiredSpace );
+
+    if ( xReturn > ( size_t ) 0 )
+    {
+        /* Was a task waiting for the data? */
+        if ( prvBytesInBuffer( pxStreamBuffer ) >= pxStreamBuffer->xTriggerLevelBytes )
+        {
+            sbSEND_COMPLETE_FROM_ISR( pxStreamBuffer, pxHigherPriorityTaskWoken );
+        }
+        else
+        {
+            mtCOVERAGE_TEST_MARKER();
+        }
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+
+    traceSTREAM_BUFFER_SEND_FROM_ISR( xStreamBuffer, xReturn );
+
+    return xReturn;
+}
+/*-----------------------------------------------------------*/
+
+static size_t prvWriteMessageToBuffer( StreamBuffer_t* const pxStreamBuffer,
+                                       const void* pvTxData,
+                                       size_t xDataLengthBytes,
+                                       size_t xSpace,
+                                       size_t xRequiredSpace )
+{
+    BaseType_t xShouldWrite;
+    size_t xReturn;
+
+    if ( xSpace == ( size_t ) 0 )
+    {
+        /* Doesn't matter if this is a stream buffer or a message buffer, there
+        is no space to write. */
+        xShouldWrite = pdFALSE;
+    }
+    else if ( ( pxStreamBuffer->ucFlags & sbFLAGS_IS_MESSAGE_BUFFER ) == ( uint8_t ) 0 )
+    {
+        /* This is a stream buffer, as opposed to a message buffer, so writing a
+        stream of bytes rather than discrete messages.  Write as many bytes as
+        possible. */
+        xShouldWrite = pdTRUE;
+        xDataLengthBytes = configMIN( xDataLengthBytes, xSpace ); /*lint !e9044 Function parameter modified to ensure it is capped to available space. */
+    }
+    else if ( xSpace >= xRequiredSpace )
+    {
+        /* This is a message buffer, as opposed to a stream buffer, and there
+        is enough space to write both the message length and the message itself
+        into the buffer.  Start by writing the length of the data, the data
+        itself will be written later in this function. */
+        xShouldWrite = pdTRUE;
+        ( void ) prvWriteBytesToBuffer( pxStreamBuffer, ( const uint8_t* ) & ( xDataLengthBytes ), sbBYTES_TO_STORE_MESSAGE_LENGTH );
+    }
+    else
+    {
+        /* There is space available, but not enough space. */
+        xShouldWrite = pdFALSE;
+    }
+
+    if ( xShouldWrite != pdFALSE )
+    {
+        /* Writes the data itself. */
+        xReturn = prvWriteBytesToBuffer( pxStreamBuffer, ( const uint8_t* ) pvTxData, xDataLengthBytes );  /*lint !e9079 Storage buffer is implemented as uint8_t for ease of sizing, alighment and access. */
+    }
+    else
+    {
+        xReturn = 0;
+    }
+
+    return xReturn;
+}
+/*-----------------------------------------------------------*/
+
+size_t xStreamBufferReceive( StreamBufferHandle_t xStreamBuffer,
+                             void* pvRxData,
+                             size_t xBufferLengthBytes,
+                             TickType_t xTicksToWait )
+{
+    StreamBuffer_t* const pxStreamBuffer = ( StreamBuffer_t* ) xStreamBuffer;   /*lint !e9087 !e9079 Safe cast as StreamBufferHandle_t is opaque Streambuffer_t. */
+    size_t xReceivedLength = 0, xBytesAvailable, xBytesToStoreMessageLength;
+
+    configASSERT( pvRxData );
+    configASSERT( pxStreamBuffer );
+
+    /* This receive function is used by both message buffers, which store
+    discrete messages, and stream buffers, which store a continuous stream of
+    bytes.  Discrete messages include an additional
+    sbBYTES_TO_STORE_MESSAGE_LENGTH bytes that hold the length of the
+    message. */
+    if ( ( pxStreamBuffer->ucFlags & sbFLAGS_IS_MESSAGE_BUFFER ) != ( uint8_t ) 0 )
+    {
+        xBytesToStoreMessageLength = sbBYTES_TO_STORE_MESSAGE_LENGTH;
+    }
+    else
+    {
+        xBytesToStoreMessageLength = 0;
+    }
+
+    if ( xTicksToWait != ( TickType_t ) 0 )
+    {
+        /* Checking if there is data and clearing the notification state must be
+        performed atomically. */
+        taskENTER_CRITICAL();
+        {
+            xBytesAvailable = prvBytesInBuffer( pxStreamBuffer );
+
+            /* If this function was invoked by a message buffer read then
+            xBytesToStoreMessageLength holds the number of bytes used to hold
+            the length of the next discrete message.  If this function was
+            invoked by a stream buffer read then xBytesToStoreMessageLength will
+            be 0. */
+            if ( xBytesAvailable <= xBytesToStoreMessageLength )
+            {
+                /* Clear notification state as going to wait for data. */
+                ( void ) xTaskNotifyStateClear( NULL );
+
+                /* Should only be one reader. */
+                configASSERT( pxStreamBuffer->xTaskWaitingToReceive == NULL );
+                pxStreamBuffer->xTaskWaitingToReceive = xTaskGetCurrentTaskHandle();
+            }
+            else
+            {
+                mtCOVERAGE_TEST_MARKER();
+            }
+        }
+        taskEXIT_CRITICAL();
+
+        if ( xBytesAvailable <= xBytesToStoreMessageLength )
+        {
+            /* Wait for data to be available. */
+            traceBLOCKING_ON_STREAM_BUFFER_RECEIVE( xStreamBuffer );
+            ( void ) xTaskNotifyWait( ( uint32_t ) 0, UINT32_MAX, NULL, xTicksToWait );
+            pxStreamBuffer->xTaskWaitingToReceive = NULL;
+
+            /* Recheck the data available after blocking. */
+            xBytesAvailable = prvBytesInBuffer( pxStreamBuffer );
+        }
+        else
+        {
+            mtCOVERAGE_TEST_MARKER();
+        }
+    }
+    else
+    {
+        xBytesAvailable = prvBytesInBuffer( pxStreamBuffer );
+    }
+
+    /* Whether receiving a discrete message (where xBytesToStoreMessageLength
+    holds the number of bytes used to store the message length) or a stream of
+    bytes (where xBytesToStoreMessageLength is zero), the number of bytes
+    available must be greater than xBytesToStoreMessageLength to be able to
+    read bytes from the buffer. */
+    if ( xBytesAvailable > xBytesToStoreMessageLength )
+    {
+        xReceivedLength = prvReadMessageFromBuffer( pxStreamBuffer, pvRxData, xBufferLengthBytes, xBytesAvailable, xBytesToStoreMessageLength );
+
+        /* Was a task waiting for space in the buffer? */
+        if ( xReceivedLength != ( size_t ) 0 )
+        {
+            traceSTREAM_BUFFER_RECEIVE( xStreamBuffer, xReceivedLength );
+            sbRECEIVE_COMPLETED( pxStreamBuffer );
+        }
+        else
+        {
+            mtCOVERAGE_TEST_MARKER();
+        }
+    }
+    else
+    {
+        traceSTREAM_BUFFER_RECEIVE_FAILED( xStreamBuffer );
+        mtCOVERAGE_TEST_MARKER();
+    }
+
+    return xReceivedLength;
+}
+/*-----------------------------------------------------------*/
+
+size_t xStreamBufferReceiveFromISR( StreamBufferHandle_t xStreamBuffer,
+                                    void* pvRxData,
+                                    size_t xBufferLengthBytes,
+                                    BaseType_t* const pxHigherPriorityTaskWoken )
+{
+    StreamBuffer_t* const pxStreamBuffer = ( StreamBuffer_t* ) xStreamBuffer;   /*lint !e9087 !e9079 Safe cast as StreamBufferHandle_t is opaque Streambuffer_t. */
+    size_t xReceivedLength = 0, xBytesAvailable, xBytesToStoreMessageLength;
+
+    configASSERT( pvRxData );
+    configASSERT( pxStreamBuffer );
+
+    /* This receive function is used by both message buffers, which store
+    discrete messages, and stream buffers, which store a continuous stream of
+    bytes.  Discrete messages include an additional
+    sbBYTES_TO_STORE_MESSAGE_LENGTH bytes that hold the length of the
+    message. */
+    if ( ( pxStreamBuffer->ucFlags & sbFLAGS_IS_MESSAGE_BUFFER ) != ( uint8_t ) 0 )
+    {
+        xBytesToStoreMessageLength = sbBYTES_TO_STORE_MESSAGE_LENGTH;
+    }
+    else
+    {
+        xBytesToStoreMessageLength = 0;
+    }
+
+    xBytesAvailable = prvBytesInBuffer( pxStreamBuffer );
+
+    /* Whether receiving a discrete message (where xBytesToStoreMessageLength
+    holds the number of bytes used to store the message length) or a stream of
+    bytes (where xBytesToStoreMessageLength is zero), the number of bytes
+    available must be greater than xBytesToStoreMessageLength to be able to
+    read bytes from the buffer. */
+    if ( xBytesAvailable > xBytesToStoreMessageLength )
+    {
+        xReceivedLength = prvReadMessageFromBuffer( pxStreamBuffer, pvRxData, xBufferLengthBytes, xBytesAvailable, xBytesToStoreMessageLength );
+
+        /* Was a task waiting for space in the buffer? */
+        if ( xReceivedLength != ( size_t ) 0 )
+        {
+            sbRECEIVE_COMPLETED_FROM_ISR( pxStreamBuffer, pxHigherPriorityTaskWoken );
+        }
+        else
+        {
+            mtCOVERAGE_TEST_MARKER();
+        }
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+
+    traceSTREAM_BUFFER_RECEIVE_FROM_ISR( xStreamBuffer, xReceivedLength );
+
+    return xReceivedLength;
+}
+/*-----------------------------------------------------------*/
+
+static size_t prvReadMessageFromBuffer( StreamBuffer_t* pxStreamBuffer,
+                                        void* pvRxData,
+                                        size_t xBufferLengthBytes,
+                                        size_t xBytesAvailable,
+                                        size_t xBytesToStoreMessageLength )
+{
+    size_t xOriginalTail, xReceivedLength, xNextMessageLength;
+
+    if ( xBytesToStoreMessageLength != ( size_t ) 0 )
+    {
+        /* A discrete message is being received.  First receive the length
+        of the message.  A copy of the tail is stored so the buffer can be
+        returned to its prior state if the length of the message is too
+        large for the provided buffer. */
+        xOriginalTail = pxStreamBuffer->xTail;
+        ( void ) prvReadBytesFromBuffer( pxStreamBuffer, ( uint8_t* ) &xNextMessageLength, xBytesToStoreMessageLength, xBytesAvailable );
+
+        /* Reduce the number of bytes available by the number of bytes just
+        read out. */
+        xBytesAvailable -= xBytesToStoreMessageLength;
+
+        /* Check there is enough space in the buffer provided by the
+        user. */
+        if ( xNextMessageLength > xBufferLengthBytes )
+        {
+            /* The user has provided insufficient space to read the message
+            so return the buffer to its previous state (so the length of
+            the message is in the buffer again). */
+            pxStreamBuffer->xTail = xOriginalTail;
+            xNextMessageLength = 0;
+        }
+        else
+        {
+            mtCOVERAGE_TEST_MARKER();
+        }
+    }
+    else
+    {
+        /* A stream of bytes is being received (as opposed to a discrete
+        message), so read as many bytes as possible. */
+        xNextMessageLength = xBufferLengthBytes;
+    }
+
+    /* Read the actual data. */
+    xReceivedLength = prvReadBytesFromBuffer( pxStreamBuffer, ( uint8_t* ) pvRxData, xNextMessageLength, xBytesAvailable );  /*lint !e9079 Data storage area is implemented as uint8_t array for ease of sizing, indexing and alignment. */
+
+    return xReceivedLength;
+}
+/*-----------------------------------------------------------*/
+
+BaseType_t xStreamBufferIsEmpty( StreamBufferHandle_t xStreamBuffer )
+{
+    const StreamBuffer_t* const pxStreamBuffer = ( StreamBuffer_t* ) xStreamBuffer;   /*lint !e9087 !e9079 Safe cast as StreamBufferHandle_t is opaque Streambuffer_t. */
+    BaseType_t xReturn;
+    size_t xTail;
+
+    configASSERT( pxStreamBuffer );
+
+    /* True if no bytes are available. */
+    xTail = pxStreamBuffer->xTail;
+
+    if ( pxStreamBuffer->xHead == xTail )
+    {
+        xReturn = pdTRUE;
+    }
+    else
+    {
+        xReturn = pdFALSE;
+    }
+
+    return xReturn;
+}
+/*-----------------------------------------------------------*/
+
+BaseType_t xStreamBufferIsFull( StreamBufferHandle_t xStreamBuffer )
+{
+    BaseType_t xReturn;
+    size_t xBytesToStoreMessageLength;
+    const StreamBuffer_t* const pxStreamBuffer = ( StreamBuffer_t* ) xStreamBuffer;   /*lint !e9087 !e9079 Safe cast as StreamBufferHandle_t is opaque Streambuffer_t. */
+
+    configASSERT( pxStreamBuffer );
+
+    /* This generic version of the receive function is used by both message
+    buffers, which store discrete messages, and stream buffers, which store a
+    continuous stream of bytes.  Discrete messages include an additional
+    sbBYTES_TO_STORE_MESSAGE_LENGTH bytes that hold the length of the message. */
+    if ( ( pxStreamBuffer->ucFlags & sbFLAGS_IS_MESSAGE_BUFFER ) != ( uint8_t ) 0 )
+    {
+        xBytesToStoreMessageLength = sbBYTES_TO_STORE_MESSAGE_LENGTH;
+    }
+    else
+    {
+        xBytesToStoreMessageLength = 0;
+    }
+
+    /* True if the available space equals zero. */
+    if ( xStreamBufferSpacesAvailable( xStreamBuffer ) <= xBytesToStoreMessageLength )
+    {
+        xReturn = pdTRUE;
+    }
+    else
+    {
+        xReturn = pdFALSE;
+    }
+
+    return xReturn;
+}
+/*-----------------------------------------------------------*/
+
+BaseType_t xStreamBufferSendCompletedFromISR( StreamBufferHandle_t xStreamBuffer, BaseType_t* pxHigherPriorityTaskWoken )
+{
+    StreamBuffer_t* const pxStreamBuffer = ( StreamBuffer_t* ) xStreamBuffer;   /*lint !e9087 !e9079 Safe cast as StreamBufferHandle_t is opaque Streambuffer_t. */
+    BaseType_t xReturn;
+    UBaseType_t uxSavedInterruptStatus;
+
+    configASSERT( pxStreamBuffer );
+
+    uxSavedInterruptStatus = ( UBaseType_t ) portSET_INTERRUPT_MASK_FROM_ISR();
+    {
+        if ( ( pxStreamBuffer )->xTaskWaitingToReceive != NULL )
+        {
+            ( void ) xTaskNotifyFromISR( ( pxStreamBuffer )->xTaskWaitingToReceive,
+                                         ( uint32_t ) 0,
+                                         eNoAction,
+                                         pxHigherPriorityTaskWoken );
+            ( pxStreamBuffer )->xTaskWaitingToReceive = NULL;
+            xReturn = pdTRUE;
+        }
+        else
+        {
+            xReturn = pdFALSE;
+        }
+    }
+    portCLEAR_INTERRUPT_MASK_FROM_ISR( uxSavedInterruptStatus );
+
+    return xReturn;
+}
+/*-----------------------------------------------------------*/
+
+BaseType_t xStreamBufferReceiveCompletedFromISR( StreamBufferHandle_t xStreamBuffer, BaseType_t* pxHigherPriorityTaskWoken )
+{
+    StreamBuffer_t* const pxStreamBuffer = ( StreamBuffer_t* ) xStreamBuffer;   /*lint !e9087 !e9079 Safe cast as StreamBufferHandle_t is opaque Streambuffer_t. */
+    BaseType_t xReturn;
+    UBaseType_t uxSavedInterruptStatus;
+
+    configASSERT( pxStreamBuffer );
+
+    uxSavedInterruptStatus = ( UBaseType_t ) portSET_INTERRUPT_MASK_FROM_ISR();
+    {
+        if ( ( pxStreamBuffer )->xTaskWaitingToSend != NULL )
+        {
+            ( void ) xTaskNotifyFromISR( ( pxStreamBuffer )->xTaskWaitingToSend,
+                                         ( uint32_t ) 0,
+                                         eNoAction,
+                                         pxHigherPriorityTaskWoken );
+            ( pxStreamBuffer )->xTaskWaitingToSend = NULL;
+            xReturn = pdTRUE;
+        }
+        else
+        {
+            xReturn = pdFALSE;
+        }
+    }
+    portCLEAR_INTERRUPT_MASK_FROM_ISR( uxSavedInterruptStatus );
+
+    return xReturn;
+}
+/*-----------------------------------------------------------*/
+
+static size_t prvWriteBytesToBuffer( StreamBuffer_t* const pxStreamBuffer, const uint8_t* pucData, size_t xCount )
+{
+    size_t xNextHead, xFirstLength;
+
+    configASSERT( xCount > ( size_t ) 0 );
+
+    xNextHead = pxStreamBuffer->xHead;
+
+    /* Calculate the number of bytes that can be added in the first write -
+    which may be less than the total number of bytes that need to be added if
+    the buffer will wrap back to the beginning. */
+    xFirstLength = configMIN( pxStreamBuffer->xLength - xNextHead, xCount );
+
+    /* Write as many bytes as can be written in the first write. */
+    configASSERT( ( xNextHead + xFirstLength ) <= pxStreamBuffer->xLength );
+    memcpy( ( void* ) ( &( pxStreamBuffer->pucBuffer[ xNextHead ] ) ), ( const void* ) pucData, xFirstLength );  /*lint !e9087 memcpy() requires void *. */
+
+    /* If the number of bytes written was less than the number that could be
+    written in the first write... */
+    if ( xCount > xFirstLength )
+    {
+        /* ...then write the remaining bytes to the start of the buffer. */
+        configASSERT( ( xCount - xFirstLength ) <= pxStreamBuffer->xLength );
+        memcpy( ( void* ) pxStreamBuffer->pucBuffer, ( const void* ) & ( pucData[ xFirstLength ] ), xCount - xFirstLength );  /*lint !e9087 memcpy() requires void *. */
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+
+    xNextHead += xCount;
+
+    if ( xNextHead >= pxStreamBuffer->xLength )
+    {
+        xNextHead -= pxStreamBuffer->xLength;
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+
+    pxStreamBuffer->xHead = xNextHead;
+
+    return xCount;
+}
+/*-----------------------------------------------------------*/
+
+static size_t prvReadBytesFromBuffer( StreamBuffer_t* pxStreamBuffer, uint8_t* pucData, size_t xMaxCount, size_t xBytesAvailable )
+{
+    size_t xCount, xFirstLength, xNextTail;
+
+    /* Use the minimum of the wanted bytes and the available bytes. */
+    xCount = configMIN( xBytesAvailable, xMaxCount );
+
+    if ( xCount > ( size_t ) 0 )
+    {
+        xNextTail = pxStreamBuffer->xTail;
+
+        /* Calculate the number of bytes that can be read - which may be
+        less than the number wanted if the data wraps around to the start of
+        the buffer. */
+        xFirstLength = configMIN( pxStreamBuffer->xLength - xNextTail, xCount );
+
+        /* Obtain the number of bytes it is possible to obtain in the first
+        read.  Asserts check bounds of read and write. */
+        configASSERT( xFirstLength <= xMaxCount );
+        configASSERT( ( xNextTail + xFirstLength ) <= pxStreamBuffer->xLength );
+        memcpy( ( void* ) pucData, ( const void* ) & ( pxStreamBuffer->pucBuffer[ xNextTail ] ), xFirstLength );  /*lint !e9087 memcpy() requires void *. */
+
+        /* If the total number of wanted bytes is greater than the number
+        that could be read in the first read... */
+        if ( xCount > xFirstLength )
+        {
+            /*...then read the remaining bytes from the start of the buffer. */
+            configASSERT( xCount <= xMaxCount );
+            memcpy( ( void* ) & ( pucData[ xFirstLength ] ), ( void* ) ( pxStreamBuffer->pucBuffer ), xCount - xFirstLength );  /*lint !e9087 memcpy() requires void *. */
+        }
+        else
+        {
+            mtCOVERAGE_TEST_MARKER();
+        }
+
+        /* Move the tail pointer to effectively remove the data read from
+        the buffer. */
+        xNextTail += xCount;
+
+        if ( xNextTail >= pxStreamBuffer->xLength )
+        {
+            xNextTail -= pxStreamBuffer->xLength;
+        }
+
+        pxStreamBuffer->xTail = xNextTail;
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+
+    return xCount;
+}
+/*-----------------------------------------------------------*/
+
+static size_t prvBytesInBuffer( const StreamBuffer_t* const pxStreamBuffer )
+{
+    /* Returns the distance between xTail and xHead. */
+    size_t xCount;
+
+    xCount = pxStreamBuffer->xLength + pxStreamBuffer->xHead;
+    xCount -= pxStreamBuffer->xTail;
+
+    if ( xCount >= pxStreamBuffer->xLength )
+    {
+        xCount -= pxStreamBuffer->xLength;
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+
+    return xCount;
+}
+/*-----------------------------------------------------------*/
+
+static void prvInitialiseNewStreamBuffer( StreamBuffer_t* const pxStreamBuffer,
+        uint8_t* const pucBuffer,
+        size_t xBufferSizeBytes,
+        size_t xTriggerLevelBytes,
+        BaseType_t xIsMessageBuffer )
+{
+    /* Assert here is deliberately writing to the entire buffer to ensure it can
+    be written to without generating exceptions, and is setting the buffer to a
+    known value to assist in development/debugging. */
+#if( configASSERT_DEFINED == 1 )
+    {
+        /* The value written just has to be identifiable when looking at the
+        memory.  Don't use 0xA5 as that is the stack fill value and could
+        result in confusion as to what is actually being observed. */
+        const BaseType_t xWriteValue = 0x55;
+        configASSERT( memset( pucBuffer, ( int ) xWriteValue, xBufferSizeBytes ) == pucBuffer );
+    }
+#endif
+
+    memset( ( void* ) pxStreamBuffer, 0x00, sizeof( StreamBuffer_t ) );  /*lint !e9087 memset() requires void *. */
+    pxStreamBuffer->pucBuffer = pucBuffer;
+    pxStreamBuffer->xLength = xBufferSizeBytes;
+    pxStreamBuffer->xTriggerLevelBytes = xTriggerLevelBytes;
+
+    if ( xIsMessageBuffer != pdFALSE )
+    {
+        pxStreamBuffer->ucFlags |= sbFLAGS_IS_MESSAGE_BUFFER;
+    }
+}
+
+#if ( configUSE_TRACE_FACILITY == 1 )
+
+UBaseType_t uxStreamBufferGetStreamBufferNumber( StreamBufferHandle_t xStreamBuffer )
+{
+    return ( ( StreamBuffer_t* ) xStreamBuffer )->uxStreamBufferNumber;
+}
+
+#endif /* configUSE_TRACE_FACILITY */
+/*-----------------------------------------------------------*/
+
+#if ( configUSE_TRACE_FACILITY == 1 )
+
+void vStreamBufferSetStreamBufferNumber( StreamBufferHandle_t xStreamBuffer, UBaseType_t uxStreamBufferNumber )
+{
+    ( ( StreamBuffer_t* ) xStreamBuffer )->uxStreamBufferNumber = uxStreamBufferNumber;
+}
+
+#endif /* configUSE_TRACE_FACILITY */
+/*-----------------------------------------------------------*/
+
+#if ( configUSE_TRACE_FACILITY == 1 )
+
+uint8_t ucStreamBufferGetStreamBufferType( StreamBufferHandle_t xStreamBuffer )
+{
+    return ( ( StreamBuffer_t* )xStreamBuffer )->ucFlags | sbFLAGS_IS_MESSAGE_BUFFER;
+}
+
+#endif /* configUSE_TRACE_FACILITY */
+/*-----------------------------------------------------------*/
diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/tasks.c b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/tasks.c
index 875bc3f3..73ed4ac4 100644
--- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/tasks.c
+++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/tasks.c
@@ -1,71 +1,29 @@
 /*
-    FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd.
-    All rights reserved
-
-    VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION.
-
-    This file is part of the FreeRTOS distribution.
-
-    FreeRTOS is free software; you can redistribute it and/or modify it under
-    the terms of the GNU General Public License (version 2) as published by the
-    Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception.
-
-    ***************************************************************************
-    >>!   NOTE: The modification to the GPL is included to allow you to     !<<
-    >>!   distribute a combined work that includes FreeRTOS without being   !<<
-    >>!   obliged to provide the source code for proprietary components     !<<
-    >>!   outside of the FreeRTOS kernel.                                   !<<
-    ***************************************************************************
-
-    FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY
-    WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
-    FOR A PARTICULAR PURPOSE.  Full license text is available on the following
-    link: http://www.freertos.org/a00114.html
-
-    ***************************************************************************
-     *                                                                       *
-     *    FreeRTOS provides completely free yet professionally developed,    *
-     *    robust, strictly quality controlled, supported, and cross          *
-     *    platform software that is more than just the market leader, it     *
-     *    is the industry's de facto standard.                               *
-     *                                                                       *
-     *    Help yourself get started quickly while simultaneously helping     *
-     *    to support the FreeRTOS project by purchasing a FreeRTOS           *
-     *    tutorial book, reference manual, or both:                          *
-     *    http://www.FreeRTOS.org/Documentation                              *
-     *                                                                       *
-    ***************************************************************************
-
-    http://www.FreeRTOS.org/FAQHelp.html - Having a problem?  Start by reading
-    the FAQ page "My application does not run, what could be wrong?".  Have you
-    defined configASSERT()?
-
-    http://www.FreeRTOS.org/support - In return for receiving this top quality
-    embedded software for free we request you assist our global community by
-    participating in the support forum.
-
-    http://www.FreeRTOS.org/training - Investing in training allows your team to
-    be as productive as possible as early as possible.  Now you can receive
-    FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers
-    Ltd, and the world's leading authority on the world's leading RTOS.
-
-    http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products,
-    including FreeRTOS+Trace - an indispensable productivity tool, a DOS
-    compatible FAT file system, and our tiny thread aware UDP/IP stack.
-
-    http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate.
-    Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS.
-
-    http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High
-    Integrity Systems ltd. to sell under the OpenRTOS brand.  Low cost OpenRTOS
-    licenses offer ticketed support, indemnification and commercial middleware.
-
-    http://www.SafeRTOS.com - High Integrity Systems also provide a safety
-    engineered and independently SIL3 certified version for use in safety and
-    mission critical applications that require provable dependability.
-
-    1 tab == 4 spaces!
-*/
+ * FreeRTOS Kernel V10.0.1
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
 
 /* Standard includes. */
 #include 
@@ -80,7 +38,7 @@ task.h is included from an application file. */
 #include "FreeRTOS.h"
 #include "task.h"
 #include "timers.h"
-#include "StackMacros.h"
+#include "stack_macros.h"
 
 /* Lint e961 and e750 are suppressed as a MISRA exception justified because the
 MPU ports require MPU_WRAPPERS_INCLUDED_FROM_API_FILE to be defined for the
@@ -98,18 +56,6 @@ for convenience only, and are NOT considered part of the kernel. */
 #include 
 #endif /* configUSE_STATS_FORMATTING_FUNCTIONS == 1 ) */
 
-/* Sanity check the configuration. */
-#if( configUSE_TICKLESS_IDLE != 0 )
-#if( INCLUDE_vTaskSuspend != 1 )
-#error INCLUDE_vTaskSuspend must be set to 1 if configUSE_TICKLESS_IDLE is not set to 0
-#endif /* INCLUDE_vTaskSuspend */
-#endif /* configUSE_TICKLESS_IDLE */
-
-/*
- * Defines the size, in words, of the stack allocated to the idle task.
- */
-#define tskIDLE_STACK_SIZE	configMINIMAL_STACK_SIZE
-
 #if( configUSE_PREEMPTION == 0 )
 /* If the cooperative scheduler is being used then a yield should not be
 performed just because a higher priority task has been woken. */
@@ -118,157 +64,10 @@ performed just because a higher priority task has been woken. */
 #define taskYIELD_IF_USING_PREEMPTION() portYIELD_WITHIN_API()
 #endif
 
-/* Value that can be assigned to the eNotifyState member of the TCB. */
-typedef enum
-{
-    eNotWaitingNotification = 0,
-    eWaitingNotification,
-    eNotified
-} eNotifyValue;
-
-/*
- * Task control block.  A task control block (TCB) is allocated for each task,
- * and stores task state information, including a pointer to the task's context
- * (the task's run time environment, including register values)
- */
-typedef struct tskTaskControlBlock
-{
-    volatile StackType_t*	pxTopOfStack;	/*< Points to the location of the last item placed on the tasks stack.  THIS MUST BE THE FIRST MEMBER OF THE TCB STRUCT. */
-
-#if ( portUSING_MPU_WRAPPERS == 1 )
-    xMPU_SETTINGS	xMPUSettings;		/*< The MPU settings are defined as part of the port layer.  THIS MUST BE THE SECOND MEMBER OF THE TCB STRUCT. */
-    BaseType_t		xUsingStaticallyAllocatedStack; /* Set to pdTRUE if the stack is a statically allocated array, and pdFALSE if the stack is dynamically allocated. */
-#endif
-
-    ListItem_t			xGenericListItem;	/*< The list that the state list item of a task is reference from denotes the state of that task (Ready, Blocked, Suspended ). */
-    ListItem_t			xEventListItem;		/*< Used to reference a task from an event list. */
-    UBaseType_t			uxPriority;			/*< The priority of the task.  0 is the lowest priority. */
-    StackType_t*			pxStack;			/*< Points to the start of the stack. */
-    char				pcTaskName[ configMAX_TASK_NAME_LEN ];/*< Descriptive name given to the task when created.  Facilitates debugging only. */ /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
-
-#if ( portSTACK_GROWTH > 0 )
-    StackType_t*		pxEndOfStack;		/*< Points to the end of the stack on architectures where the stack grows up from low memory. */
-#endif
-
-#if ( portCRITICAL_NESTING_IN_TCB == 1 )
-    UBaseType_t 	uxCriticalNesting; 	/*< Holds the critical section nesting depth for ports that do not maintain their own count in the port layer. */
-#endif
-
-#if ( configUSE_TRACE_FACILITY == 1 )
-    UBaseType_t		uxTCBNumber;		/*< Stores a number that increments each time a TCB is created.  It allows debuggers to determine when a task has been deleted and then recreated. */
-    UBaseType_t  	uxTaskNumber;		/*< Stores a number specifically for use by third party trace code. */
-#endif
-
-#if ( configUSE_MUTEXES == 1 )
-    UBaseType_t 	uxBasePriority;		/*< The priority last assigned to the task - used by the priority inheritance mechanism. */
-    UBaseType_t 	uxMutexesHeld;
-#endif
-
-#if ( configUSE_APPLICATION_TASK_TAG == 1 )
-    TaskHookFunction_t pxTaskTag;
-#endif
-
-#if( configNUM_THREAD_LOCAL_STORAGE_POINTERS > 0 )
-    void* pvThreadLocalStoragePointers[ configNUM_THREAD_LOCAL_STORAGE_POINTERS ];
-#endif
-
-#if ( configGENERATE_RUN_TIME_STATS == 1 )
-    uint32_t		ulRunTimeCounter;	/*< Stores the amount of time the task has spent in the Running state. */
-#endif
-
-#if ( configUSE_NEWLIB_REENTRANT == 1 )
-    /* Allocate a Newlib reent structure that is specific to this task.
-    Note Newlib support has been included by popular demand, but is not
-    used by the FreeRTOS maintainers themselves.  FreeRTOS is not
-    responsible for resulting newlib operation.  User must be familiar with
-    newlib and must provide system-wide implementations of the necessary
-    stubs. Be warned that (at the time of writing) the current newlib design
-    implements a system-wide malloc() that must be provided with locks. */
-    struct 	_reent xNewLib_reent;
-#endif
-
-#if ( configUSE_TASK_NOTIFICATIONS == 1 )
-    volatile uint32_t ulNotifiedValue;
-    volatile eNotifyValue eNotifyState;
-#endif
-
-} tskTCB;
-
-/* The old tskTCB name is maintained above then typedefed to the new TCB_t name
-below to enable the use of older kernel aware debuggers. */
-typedef tskTCB TCB_t;
-
-/*
- * Some kernel aware debuggers require the data the debugger needs access to to
- * be global, rather than file scope.
- */
-#ifdef portREMOVE_STATIC_QUALIFIER
-#define static
-#endif
-
-/*lint -e956 A manual analysis and inspection has been used to determine which
-static variables must be declared volatile. */
-
-PRIVILEGED_DATA TCB_t* volatile pxCurrentTCB = NULL;
-
-/* Lists for ready and blocked tasks. --------------------*/
-PRIVILEGED_DATA static List_t pxReadyTasksLists[ configMAX_PRIORITIES ];/*< Prioritised ready tasks. */
-PRIVILEGED_DATA static List_t xDelayedTaskList1;						/*< Delayed tasks. */
-PRIVILEGED_DATA static List_t xDelayedTaskList2;						/*< Delayed tasks (two lists are used - one for delays that have overflowed the current tick count. */
-PRIVILEGED_DATA static List_t* volatile pxDelayedTaskList;				/*< Points to the delayed task list currently being used. */
-PRIVILEGED_DATA static List_t* volatile pxOverflowDelayedTaskList;		/*< Points to the delayed task list currently being used to hold tasks that have overflowed the current tick count. */
-PRIVILEGED_DATA static List_t xPendingReadyList;						/*< Tasks that have been readied while the scheduler was suspended.  They will be moved to the ready list when the scheduler is resumed. */
-
-#if ( INCLUDE_vTaskDelete == 1 )
-
-PRIVILEGED_DATA static List_t xTasksWaitingTermination;				/*< Tasks that have been deleted - but their memory not yet freed. */
-PRIVILEGED_DATA static volatile UBaseType_t uxTasksDeleted = ( UBaseType_t ) 0U;
-
-#endif
-
-#if ( INCLUDE_vTaskSuspend == 1 )
-
-PRIVILEGED_DATA static List_t xSuspendedTaskList;					/*< Tasks that are currently suspended. */
-
-#endif
-
-#if ( INCLUDE_xTaskGetIdleTaskHandle == 1 )
-
-PRIVILEGED_DATA static TaskHandle_t xIdleTaskHandle = NULL;			/*< Holds the handle of the idle task.  The idle task is created automatically when the scheduler is started. */
-
-#endif
-
-/* Other file private variables. --------------------------------*/
-PRIVILEGED_DATA static volatile UBaseType_t uxCurrentNumberOfTasks 	= ( UBaseType_t ) 0U;
-PRIVILEGED_DATA static volatile TickType_t xTickCount 				= ( TickType_t ) 0U;
-PRIVILEGED_DATA static volatile UBaseType_t uxTopReadyPriority 		= tskIDLE_PRIORITY;
-PRIVILEGED_DATA static volatile BaseType_t xSchedulerRunning 		= pdFALSE;
-PRIVILEGED_DATA static volatile UBaseType_t uxPendedTicks 			= ( UBaseType_t ) 0U;
-PRIVILEGED_DATA static volatile BaseType_t xYieldPending 			= pdFALSE;
-PRIVILEGED_DATA static volatile BaseType_t xNumOfOverflows 			= ( BaseType_t ) 0;
-PRIVILEGED_DATA static UBaseType_t uxTaskNumber 					= ( UBaseType_t ) 0U;
-PRIVILEGED_DATA static volatile TickType_t xNextTaskUnblockTime		= ( TickType_t ) 0U; /* Initialised to portMAX_DELAY before the scheduler starts. */
-
-/* Context switches are held pending while the scheduler is suspended.  Also,
-interrupts must not manipulate the xGenericListItem of a TCB, or any of the
-lists the xGenericListItem can be referenced from, if the scheduler is suspended.
-If an interrupt needs to unblock a task while the scheduler is suspended then it
-moves the task's event list item into the xPendingReadyList, ready for the
-kernel to move the task from the pending ready list into the real ready list
-when the scheduler is unsuspended.  The pending ready list itself can only be
-accessed from a critical section. */
-PRIVILEGED_DATA static volatile UBaseType_t uxSchedulerSuspended	= ( UBaseType_t ) pdFALSE;
-
-#if ( configGENERATE_RUN_TIME_STATS == 1 )
-
-PRIVILEGED_DATA static uint32_t ulTaskSwitchedInTime = 0UL;	/*< Holds the value of a timer/counter the last time a task was switched in. */
-PRIVILEGED_DATA static uint32_t ulTotalRunTime = 0UL;		/*< Holds the total amount of execution time as defined by the run time counter clock. */
-
-#endif
-
-/*lint +e956 */
-
-/* Debugging and trace facilities private variables and macros. ------------*/
+/* Values that can be assigned to the ucNotifyState member of the TCB. */
+#define taskNOT_WAITING_NOTIFICATION	( ( uint8_t ) 0 )
+#define taskWAITING_NOTIFICATION		( ( uint8_t ) 1 )
+#define taskNOTIFICATION_RECEIVED		( ( uint8_t ) 2 )
 
 /*
  * The value used to fill the stack of a task when the task is created.  This
@@ -276,15 +75,59 @@ PRIVILEGED_DATA static uint32_t ulTotalRunTime = 0UL;		/*< Holds the total amoun
  */
 #define tskSTACK_FILL_BYTE	( 0xa5U )
 
+/* Sometimes the FreeRTOSConfig.h settings only allow a task to be created using
+dynamically allocated RAM, in which case when any task is deleted it is known
+that both the task's stack and TCB need to be freed.  Sometimes the
+FreeRTOSConfig.h settings only allow a task to be created using statically
+allocated RAM, in which case when any task is deleted it is known that neither
+the task's stack or TCB should be freed.  Sometimes the FreeRTOSConfig.h
+settings allow a task to be created using either statically or dynamically
+allocated RAM, in which case a member of the TCB is used to record whether the
+stack and/or TCB were allocated statically or dynamically, so when a task is
+deleted the RAM that was allocated dynamically is freed again and no attempt is
+made to free the RAM that was allocated statically.
+tskSTATIC_AND_DYNAMIC_ALLOCATION_POSSIBLE is only true if it is possible for a
+task to be created using either statically or dynamically allocated RAM.  Note
+that if portUSING_MPU_WRAPPERS is 1 then a protected task can be created with
+a statically allocated stack and a dynamically allocated TCB.
+!!!NOTE!!! If the definition of tskSTATIC_AND_DYNAMIC_ALLOCATION_POSSIBLE is
+changed then the definition of StaticTask_t must also be updated. */
+#define tskSTATIC_AND_DYNAMIC_ALLOCATION_POSSIBLE	( ( configSUPPORT_STATIC_ALLOCATION == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) )
+#define tskDYNAMICALLY_ALLOCATED_STACK_AND_TCB 		( ( uint8_t ) 0 )
+#define tskSTATICALLY_ALLOCATED_STACK_ONLY 			( ( uint8_t ) 1 )
+#define tskSTATICALLY_ALLOCATED_STACK_AND_TCB		( ( uint8_t ) 2 )
+
+/* If any of the following are set then task stacks are filled with a known
+value so the high water mark can be determined.  If none of the following are
+set then don't fill the stack so there is no unnecessary dependency on memset. */
+#if( ( configCHECK_FOR_STACK_OVERFLOW > 1 ) || ( configUSE_TRACE_FACILITY == 1 ) || ( INCLUDE_uxTaskGetStackHighWaterMark == 1 ) )
+#define tskSET_NEW_STACKS_TO_KNOWN_VALUE	1
+#else
+#define tskSET_NEW_STACKS_TO_KNOWN_VALUE	0
+#endif
+
 /*
  * Macros used by vListTask to indicate which state a task is in.
  */
+#define tskRUNNING_CHAR		( 'X' )
 #define tskBLOCKED_CHAR		( 'B' )
 #define tskREADY_CHAR		( 'R' )
 #define tskDELETED_CHAR		( 'D' )
 #define tskSUSPENDED_CHAR	( 'S' )
 
-/*-----------------------------------------------------------*/
+/*
+ * Some kernel aware debuggers require the data the debugger needs access to be
+ * global, rather than file scope.
+ */
+#ifdef portREMOVE_STATIC_QUALIFIER
+#define static
+#endif
+
+/* The name allocated to the Idle task.  This can be overridden by defining
+configIDLE_TASK_NAME in FreeRTOSConfig.h. */
+#ifndef configIDLE_TASK_NAME
+#define configIDLE_TASK_NAME "IDLE"
+#endif
 
 #if ( configUSE_PORT_OPTIMISED_TASK_SELECTION == 0 )
 
@@ -306,16 +149,19 @@ state task. */
 
 #define taskSELECT_HIGHEST_PRIORITY_TASK()															\
 	{																									\
+	UBaseType_t uxTopPriority = uxTopReadyPriority;														\
+																										\
 		/* Find the highest priority queue that contains ready tasks. */								\
-		while( listLIST_IS_EMPTY( &( pxReadyTasksLists[ uxTopReadyPriority ] ) ) )						\
+		while( listLIST_IS_EMPTY( &( pxReadyTasksLists[ uxTopPriority ] ) ) )							\
 		{																								\
-			configASSERT( uxTopReadyPriority );															\
-			--uxTopReadyPriority;																		\
+			configASSERT( uxTopPriority );																\
+			--uxTopPriority;																			\
 		}																								\
 																										\
 		/* listGET_OWNER_OF_NEXT_ENTRY indexes through the list, so the tasks of						\
 		the	same priority get an equal share of the processor time. */									\
-		listGET_OWNER_OF_NEXT_ENTRY( pxCurrentTCB, &( pxReadyTasksLists[ uxTopReadyPriority ] ) );		\
+		listGET_OWNER_OF_NEXT_ENTRY( pxCurrentTCB, &( pxReadyTasksLists[ uxTopPriority ] ) );			\
+		uxTopReadyPriority = uxTopPriority;																\
 	} /* taskSELECT_HIGHEST_PRIORITY_TASK */
 
 /*-----------------------------------------------------------*/
@@ -341,7 +187,7 @@ architecture being used. */
 	{																								\
 	UBaseType_t uxTopPriority;																		\
 																									\
-		/* Find the highest priority queue that contains ready tasks. */							\
+		/* Find the highest priority list that contains ready tasks. */								\
 		portGET_HIGHEST_PRIORITY( uxTopPriority, uxTopReadyPriority );								\
 		configASSERT( listCURRENT_LIST_LENGTH( &( pxReadyTasksLists[ uxTopPriority ] ) ) > 0 );		\
 		listGET_OWNER_OF_NEXT_ENTRY( pxCurrentTCB, &( pxReadyTasksLists[ uxTopPriority ] ) );		\
@@ -389,7 +235,8 @@ count overflows. */
 #define prvAddTaskToReadyList( pxTCB )																\
 	traceMOVED_TASK_TO_READY_STATE( pxTCB );														\
 	taskRECORD_READY_PRIORITY( ( pxTCB )->uxPriority );												\
-	vListInsertEnd( &( pxReadyTasksLists[ ( pxTCB )->uxPriority ] ), &( ( pxTCB )->xGenericListItem ) )
+	vListInsertEnd( &( pxReadyTasksLists[ ( pxTCB )->uxPriority ] ), &( ( pxTCB )->xStateListItem ) ); \
+	tracePOST_MOVED_TASK_TO_READY_STATE( pxTCB )
 /*-----------------------------------------------------------*/
 
 /*
@@ -408,28 +255,166 @@ being used for another purpose.  The following bit definition is used to inform
 the scheduler that the value should not be changed - in which case it is the
 responsibility of whichever module is using the value to ensure it gets set back
 to its original value when it is released. */
-#if configUSE_16_BIT_TICKS == 1
+#if( configUSE_16_BIT_TICKS == 1 )
 #define taskEVENT_LIST_ITEM_VALUE_IN_USE	0x8000U
 #else
 #define taskEVENT_LIST_ITEM_VALUE_IN_USE	0x80000000UL
 #endif
 
+/*
+ * Task control block.  A task control block (TCB) is allocated for each task,
+ * and stores task state information, including a pointer to the task's context
+ * (the task's run time environment, including register values)
+ */
+typedef struct tskTaskControlBlock
+{
+    volatile StackType_t*	pxTopOfStack;	/*< Points to the location of the last item placed on the tasks stack.  THIS MUST BE THE FIRST MEMBER OF THE TCB STRUCT. */
+
+#if ( portUSING_MPU_WRAPPERS == 1 )
+    xMPU_SETTINGS	xMPUSettings;		/*< The MPU settings are defined as part of the port layer.  THIS MUST BE THE SECOND MEMBER OF THE TCB STRUCT. */
+#endif
+
+    ListItem_t			xStateListItem;	/*< The list that the state list item of a task is reference from denotes the state of that task (Ready, Blocked, Suspended ). */
+    ListItem_t			xEventListItem;		/*< Used to reference a task from an event list. */
+    UBaseType_t			uxPriority;			/*< The priority of the task.  0 is the lowest priority. */
+    StackType_t*			pxStack;			/*< Points to the start of the stack. */
+    char				pcTaskName[ configMAX_TASK_NAME_LEN ];/*< Descriptive name given to the task when created.  Facilitates debugging only. */ /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+
+#if ( ( portSTACK_GROWTH > 0 ) || ( configRECORD_STACK_HIGH_ADDRESS == 1 ) )
+    StackType_t*		pxEndOfStack;		/*< Points to the highest valid address for the stack. */
+#endif
+
+#if ( portCRITICAL_NESTING_IN_TCB == 1 )
+    UBaseType_t		uxCriticalNesting;	/*< Holds the critical section nesting depth for ports that do not maintain their own count in the port layer. */
+#endif
+
+#if ( configUSE_TRACE_FACILITY == 1 )
+    UBaseType_t		uxTCBNumber;		/*< Stores a number that increments each time a TCB is created.  It allows debuggers to determine when a task has been deleted and then recreated. */
+    UBaseType_t		uxTaskNumber;		/*< Stores a number specifically for use by third party trace code. */
+#endif
+
+#if ( configUSE_MUTEXES == 1 )
+    UBaseType_t		uxBasePriority;		/*< The priority last assigned to the task - used by the priority inheritance mechanism. */
+    UBaseType_t		uxMutexesHeld;
+#endif
+
+#if ( configUSE_APPLICATION_TASK_TAG == 1 )
+    TaskHookFunction_t pxTaskTag;
+#endif
+
+#if( configNUM_THREAD_LOCAL_STORAGE_POINTERS > 0 )
+    void*			pvThreadLocalStoragePointers[ configNUM_THREAD_LOCAL_STORAGE_POINTERS ];
+#endif
+
+#if( configGENERATE_RUN_TIME_STATS == 1 )
+    uint32_t		ulRunTimeCounter;	/*< Stores the amount of time the task has spent in the Running state. */
+#endif
+
+#if ( configUSE_NEWLIB_REENTRANT == 1 )
+    /* Allocate a Newlib reent structure that is specific to this task.
+    Note Newlib support has been included by popular demand, but is not
+    used by the FreeRTOS maintainers themselves.  FreeRTOS is not
+    responsible for resulting newlib operation.  User must be familiar with
+    newlib and must provide system-wide implementations of the necessary
+    stubs. Be warned that (at the time of writing) the current newlib design
+    implements a system-wide malloc() that must be provided with locks. */
+    struct	_reent xNewLib_reent;
+#endif
+
+#if( configUSE_TASK_NOTIFICATIONS == 1 )
+    volatile uint32_t ulNotifiedValue;
+    volatile uint8_t ucNotifyState;
+#endif
+
+    /* See the comments above the definition of
+    tskSTATIC_AND_DYNAMIC_ALLOCATION_POSSIBLE. */
+#if( tskSTATIC_AND_DYNAMIC_ALLOCATION_POSSIBLE != 0 ) /*lint !e731 Macro has been consolidated for readability reasons. */
+    uint8_t	ucStaticallyAllocated; 		/*< Set to pdTRUE if the task is a statically allocated to ensure no attempt is made to free the memory. */
+#endif
+
+#if( INCLUDE_xTaskAbortDelay == 1 )
+    uint8_t ucDelayAborted;
+#endif
+
+} tskTCB;
+
+/* The old tskTCB name is maintained above then typedefed to the new TCB_t name
+below to enable the use of older kernel aware debuggers. */
+typedef tskTCB TCB_t;
+
+/*lint -save -e956 A manual analysis and inspection has been used to determine
+which static variables must be declared volatile. */
+
+PRIVILEGED_DATA TCB_t* volatile pxCurrentTCB = NULL;
+
+/* Lists for ready and blocked tasks. --------------------*/
+PRIVILEGED_DATA static List_t pxReadyTasksLists[ configMAX_PRIORITIES ] = {0};	/*< Prioritised ready tasks. */
+PRIVILEGED_DATA static List_t xDelayedTaskList1 = {0};								/*< Delayed tasks. */
+PRIVILEGED_DATA static List_t xDelayedTaskList2 = {0};								/*< Delayed tasks (two lists are used - one for delays that have overflowed the current tick count. */
+PRIVILEGED_DATA static List_t* volatile pxDelayedTaskList = NULL;					/*< Points to the delayed task list currently being used. */
+PRIVILEGED_DATA static List_t* volatile pxOverflowDelayedTaskList = NULL;			/*< Points to the delayed task list currently being used to hold tasks that have overflowed the current tick count. */
+PRIVILEGED_DATA static List_t xPendingReadyList = {0};								/*< Tasks that have been readied while the scheduler was suspended.  They will be moved to the ready list when the scheduler is resumed. */
+
+#if( INCLUDE_vTaskDelete == 1 )
+
+PRIVILEGED_DATA static List_t xTasksWaitingTermination = {0};					/*< Tasks that have been deleted - but their memory not yet freed. */
+PRIVILEGED_DATA static volatile UBaseType_t uxDeletedTasksWaitingCleanUp = ( UBaseType_t ) 0U;
+
+#endif
+
+#if ( INCLUDE_vTaskSuspend == 1 )
+
+PRIVILEGED_DATA static List_t xSuspendedTaskList = {0};						/*< Tasks that are currently suspended. */
+
+#endif
+
+/* Other file private variables. --------------------------------*/
+PRIVILEGED_DATA static volatile UBaseType_t uxCurrentNumberOfTasks 	= ( UBaseType_t ) 0U;
+PRIVILEGED_DATA static volatile TickType_t xTickCount 				= ( TickType_t ) configINITIAL_TICK_COUNT;
+PRIVILEGED_DATA static volatile UBaseType_t uxTopReadyPriority 		= tskIDLE_PRIORITY;
+PRIVILEGED_DATA static volatile BaseType_t xSchedulerRunning 		= pdFALSE;
+PRIVILEGED_DATA static volatile UBaseType_t uxPendedTicks 			= ( UBaseType_t ) 0U;
+PRIVILEGED_DATA static volatile BaseType_t xYieldPending 			= pdFALSE;
+PRIVILEGED_DATA static volatile BaseType_t xNumOfOverflows 			= ( BaseType_t ) 0;
+PRIVILEGED_DATA static UBaseType_t uxTaskNumber 					= ( UBaseType_t ) 0U;
+PRIVILEGED_DATA static volatile TickType_t xNextTaskUnblockTime		= ( TickType_t ) 0U; /* Initialised to portMAX_DELAY before the scheduler starts. */
+PRIVILEGED_DATA static TaskHandle_t xIdleTaskHandle					= NULL;			/*< Holds the handle of the idle task.  The idle task is created automatically when the scheduler is started. */
+
+/* Context switches are held pending while the scheduler is suspended.  Also,
+interrupts must not manipulate the xStateListItem of a TCB, or any of the
+lists the xStateListItem can be referenced from, if the scheduler is suspended.
+If an interrupt needs to unblock a task while the scheduler is suspended then it
+moves the task's event list item into the xPendingReadyList, ready for the
+kernel to move the task from the pending ready list into the real ready list
+when the scheduler is unsuspended.  The pending ready list itself can only be
+accessed from a critical section. */
+PRIVILEGED_DATA static volatile UBaseType_t uxSchedulerSuspended	= ( UBaseType_t ) pdFALSE;
+
+#if ( configGENERATE_RUN_TIME_STATS == 1 )
+
+PRIVILEGED_DATA static uint32_t ulTaskSwitchedInTime = 0UL;	/*< Holds the value of a timer/counter the last time a task was switched in. */
+PRIVILEGED_DATA static uint32_t ulTotalRunTime = 0UL;		/*< Holds the total amount of execution time as defined by the run time counter clock. */
+
+#endif
+
+/*lint -restore */
+
+/*-----------------------------------------------------------*/
+
 /* Callback function prototypes. --------------------------*/
-#if configCHECK_FOR_STACK_OVERFLOW > 0
+#if(  configCHECK_FOR_STACK_OVERFLOW > 0 )
 extern void vApplicationStackOverflowHook( TaskHandle_t xTask, char* pcTaskName );
 #endif
 
-#if configUSE_TICK_HOOK > 0
+#if( configUSE_TICK_HOOK > 0 )
 extern void vApplicationTickHook( void );
 #endif
 
-/* File private functions. --------------------------------*/
+#if( configSUPPORT_STATIC_ALLOCATION == 1 )
+extern void vApplicationGetIdleTaskMemory( StaticTask_t** ppxIdleTaskTCBBuffer, StackType_t** ppxIdleTaskStackBuffer, uint32_t* pulIdleTaskStackSize );
+#endif
 
-/*
- * Utility to ready a TCB for a given task.  Mainly just copies the parameters
- * into the TCB structure.
- */
-static void prvInitialiseTCBVariables( TCB_t* const pxTCB, const char* const pcName, UBaseType_t uxPriority, const MemoryRegion_t* const xRegions, const uint16_t usStackDepth ) PRIVILEGED_FUNCTION;    /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+/* File private functions. --------------------------------*/
 
 /**
  * Utility task that simply returns pdTRUE if the task referenced by xTask is
@@ -437,7 +422,9 @@ static void prvInitialiseTCBVariables( TCB_t* const pxTCB, const char* const pcN
  * is in any other state.
  */
 #if ( INCLUDE_vTaskSuspend == 1 )
+
 static BaseType_t prvTaskIsTaskSuspended( const TaskHandle_t xTask ) PRIVILEGED_FUNCTION;
+
 #endif /* INCLUDE_vTaskSuspend */
 
 /*
@@ -483,13 +470,7 @@ static void prvCheckTasksWaitingTermination( void ) PRIVILEGED_FUNCTION;
  * The currently executing task is entering the Blocked state.  Add the task to
  * either the current or the overflow delayed task list.
  */
-static void prvAddCurrentTaskToDelayedList( const TickType_t xTimeToWake ) PRIVILEGED_FUNCTION;
-
-/*
- * Allocates memory from the heap for a TCB and associated stack.  Checks the
- * allocation was successful.
- */
-static TCB_t* prvAllocateTCBAndStack( const uint16_t usStackDepth, StackType_t* const puxStackBuffer ) PRIVILEGED_FUNCTION;
+static void prvAddCurrentTaskToDelayedList( TickType_t xTicksToWait, const BaseType_t xCanBlockIndefinitely ) PRIVILEGED_FUNCTION;
 
 /*
  * Fills an TaskStatus_t structure with information on each task that is
@@ -501,7 +482,17 @@ static TCB_t* prvAllocateTCBAndStack( const uint16_t usStackDepth, StackType_t*
  */
 #if ( configUSE_TRACE_FACILITY == 1 )
 
-static UBaseType_t prvListTaskWithinSingleList( TaskStatus_t* pxTaskStatusArray, List_t* pxList, eTaskState eState ) PRIVILEGED_FUNCTION;
+static UBaseType_t prvListTasksWithinSingleList( TaskStatus_t* pxTaskStatusArray, List_t* pxList, eTaskState eState ) PRIVILEGED_FUNCTION;
+
+#endif
+
+/*
+ * Searches pxList for a task with name pcNameToQuery - returning a handle to
+ * the task if it is found, or NULL if the task is not found.
+ */
+#if ( INCLUDE_xTaskGetHandle == 1 )
+
+static TCB_t* prvSearchForNameWithinSingleList( List_t* pxList, const char pcNameToQuery[] ) PRIVILEGED_FUNCTION;
 
 #endif
 
@@ -543,192 +534,573 @@ static void prvResetNextTaskUnblockTime( void );
  * Helper function used to pad task names with spaces when printing out
  * human readable tables of task information.
  */
-static char* prvWriteNameToBuffer( char* pcBuffer, const char* pcTaskName );
+static char* prvWriteNameToBuffer( char* pcBuffer, const char* pcTaskName ) PRIVILEGED_FUNCTION;
+
+#endif
+
+/*
+ * Called after a Task_t structure has been allocated either statically or
+ * dynamically to fill in the structure's members.
+ */
+static void prvInitialiseNewTask( 	TaskFunction_t pxTaskCode,
+                                    const char* const pcName, 		/*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+                                    const uint32_t ulStackDepth,
+                                    void* const pvParameters,
+                                    UBaseType_t uxPriority,
+                                    TaskHandle_t* const pxCreatedTask,
+                                    TCB_t* pxNewTCB,
+                                    const MemoryRegion_t* const xRegions ) PRIVILEGED_FUNCTION;
+
+/*
+ * Called after a new task has been created and initialised to place the task
+ * under the control of the scheduler.
+ */
+static void prvAddNewTaskToReadyList( TCB_t* pxNewTCB ) PRIVILEGED_FUNCTION;
+
+/*
+ * freertos_tasks_c_additions_init() should only be called if the user definable
+ * macro FREERTOS_TASKS_C_ADDITIONS_INIT() is defined, as that is the only macro
+ * called by the function.
+ */
+#ifdef FREERTOS_TASKS_C_ADDITIONS_INIT
+
+static void freertos_tasks_c_additions_init( void ) PRIVILEGED_FUNCTION;
 
 #endif
+
 /*-----------------------------------------------------------*/
 
-BaseType_t xTaskGenericCreate( TaskFunction_t pxTaskCode, const char* const pcName, const uint16_t usStackDepth, void* const pvParameters, UBaseType_t uxPriority, TaskHandle_t* const pxCreatedTask, StackType_t* const puxStackBuffer, const MemoryRegion_t* const xRegions )      /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+#if( configSUPPORT_STATIC_ALLOCATION == 1 )
+
+TaskHandle_t xTaskCreateStatic(	TaskFunction_t pxTaskCode,
+                                const char* const pcName,		/*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+                                const uint32_t ulStackDepth,
+                                void* const pvParameters,
+                                UBaseType_t uxPriority,
+                                StackType_t* const puxStackBuffer,
+                                StaticTask_t* const pxTaskBuffer )
 {
-    BaseType_t xReturn;
     TCB_t* pxNewTCB;
-    StackType_t* pxTopOfStack;
-    configASSERT( pxTaskCode );
-    configASSERT( ( ( uxPriority & ( UBaseType_t ) ( ~portPRIVILEGE_BIT ) ) < ( UBaseType_t ) configMAX_PRIORITIES ) );
-    /* Allocate the memory required by the TCB and stack for the new task,
-    checking that the allocation was successful. */
-    pxNewTCB = prvAllocateTCBAndStack( usStackDepth, puxStackBuffer );
+    TaskHandle_t xReturn;
 
-    if ( pxNewTCB != NULL )
+    configASSERT( puxStackBuffer != NULL );
+    configASSERT( pxTaskBuffer != NULL );
+
+#if( configASSERT_DEFINED == 1 )
     {
-#if( portUSING_MPU_WRAPPERS == 1 )
-        /* Should the task be created in privileged mode? */
-        BaseType_t xRunPrivileged;
+        /* Sanity check that the size of the structure used to declare a
+        variable of type StaticTask_t equals the size of the real task
+        structure. */
+        volatile size_t xSize = sizeof( StaticTask_t );
+        configASSERT( xSize == sizeof( TCB_t ) );
+    }
+#endif /* configASSERT_DEFINED */
 
-        if ( ( uxPriority & portPRIVILEGE_BIT ) != 0U )
+
+    if ( ( pxTaskBuffer != NULL ) && ( puxStackBuffer != NULL ) )
+    {
+        /* The memory used for the task's TCB and stack are passed into this
+        function - use them. */
+        pxNewTCB = ( TCB_t* ) pxTaskBuffer;  /*lint !e740 Unusual cast is ok as the structures are designed to have the same alignment, and the size is checked by an assert. */
+        pxNewTCB->pxStack = ( StackType_t* ) puxStackBuffer;
+
+#if( tskSTATIC_AND_DYNAMIC_ALLOCATION_POSSIBLE != 0 ) /*lint !e731 Macro has been consolidated for readability reasons. */
         {
-            xRunPrivileged = pdTRUE;
+            /* Tasks can be created statically or dynamically, so note this
+            task was created statically in case the task is later deleted. */
+            pxNewTCB->ucStaticallyAllocated = tskSTATICALLY_ALLOCATED_STACK_AND_TCB;
         }
-        else
+#endif /* configSUPPORT_DYNAMIC_ALLOCATION */
+
+        prvInitialiseNewTask( pxTaskCode, pcName, ulStackDepth, pvParameters, uxPriority, &xReturn, pxNewTCB, NULL );
+        prvAddNewTaskToReadyList( pxNewTCB );
+    }
+    else
+    {
+        xReturn = NULL;
+    }
+
+    return xReturn;
+}
+
+#endif /* SUPPORT_STATIC_ALLOCATION */
+/*-----------------------------------------------------------*/
+
+#if( ( portUSING_MPU_WRAPPERS == 1 ) && ( configSUPPORT_STATIC_ALLOCATION == 1 ) )
+
+BaseType_t xTaskCreateRestrictedStatic( const TaskParameters_t* const pxTaskDefinition, TaskHandle_t* pxCreatedTask )
+{
+    TCB_t* pxNewTCB;
+    BaseType_t xReturn = errCOULD_NOT_ALLOCATE_REQUIRED_MEMORY;
+
+    configASSERT( pxTaskDefinition->puxStackBuffer != NULL );
+    configASSERT( pxTaskDefinition->pxTaskBuffer != NULL );
+
+    if ( ( pxTaskDefinition->puxStackBuffer != NULL ) && ( pxTaskDefinition->pxTaskBuffer != NULL ) )
+    {
+        /* Allocate space for the TCB.  Where the memory comes from depends
+        on the implementation of the port malloc function and whether or
+        not static allocation is being used. */
+        pxNewTCB = ( TCB_t* ) pxTaskDefinition->pxTaskBuffer;
+
+        /* Store the stack location in the TCB. */
+        pxNewTCB->pxStack = pxTaskDefinition->puxStackBuffer;
+
+#if( tskSTATIC_AND_DYNAMIC_ALLOCATION_POSSIBLE != 0 )
         {
-            xRunPrivileged = pdFALSE;
+            /* Tasks can be created statically or dynamically, so note this
+            task was created statically in case the task is later deleted. */
+            pxNewTCB->ucStaticallyAllocated = tskSTATICALLY_ALLOCATED_STACK_AND_TCB;
         }
+#endif /* configSUPPORT_DYNAMIC_ALLOCATION */
+
+        prvInitialiseNewTask(	pxTaskDefinition->pvTaskCode,
+                                pxTaskDefinition->pcName,
+                                ( uint32_t ) pxTaskDefinition->usStackDepth,
+                                pxTaskDefinition->pvParameters,
+                                pxTaskDefinition->uxPriority,
+                                pxCreatedTask, pxNewTCB,
+                                pxTaskDefinition->xRegions );
+
+        prvAddNewTaskToReadyList( pxNewTCB );
+        xReturn = pdPASS;
+    }
+
+    return xReturn;
+}
+
+#endif /* ( portUSING_MPU_WRAPPERS == 1 ) && ( configSUPPORT_STATIC_ALLOCATION == 1 ) */
+/*-----------------------------------------------------------*/
+
+#if( ( portUSING_MPU_WRAPPERS == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) )
+
+BaseType_t xTaskCreateRestricted( const TaskParameters_t* const pxTaskDefinition, TaskHandle_t* pxCreatedTask )
+{
+    TCB_t* pxNewTCB;
+    BaseType_t xReturn = errCOULD_NOT_ALLOCATE_REQUIRED_MEMORY;
+
+    configASSERT( pxTaskDefinition->puxStackBuffer );
 
-        uxPriority &= ~portPRIVILEGE_BIT;
+    if ( pxTaskDefinition->puxStackBuffer != NULL )
+    {
+        /* Allocate space for the TCB.  Where the memory comes from depends
+        on the implementation of the port malloc function and whether or
+        not static allocation is being used. */
+        pxNewTCB = ( TCB_t* ) pvPortMalloc( sizeof( TCB_t ) );
 
-        if ( puxStackBuffer != NULL )
+        if ( pxNewTCB != NULL )
         {
-            /* The application provided its own stack.  Note this so no
-            attempt is made to delete the stack should that task be
-            deleted. */
-            pxNewTCB->xUsingStaticallyAllocatedStack = pdTRUE;
+            /* Store the stack location in the TCB. */
+            pxNewTCB->pxStack = pxTaskDefinition->puxStackBuffer;
+
+#if( configSUPPORT_STATIC_ALLOCATION == 1 )
+            {
+                /* Tasks can be created statically or dynamically, so note
+                this task had a statically allocated stack in case it is
+                later deleted.  The TCB was allocated dynamically. */
+                pxNewTCB->ucStaticallyAllocated = tskSTATICALLY_ALLOCATED_STACK_ONLY;
+            }
+#endif
+
+            prvInitialiseNewTask(	pxTaskDefinition->pvTaskCode,
+                                    pxTaskDefinition->pcName,
+                                    ( uint32_t ) pxTaskDefinition->usStackDepth,
+                                    pxTaskDefinition->pvParameters,
+                                    pxTaskDefinition->uxPriority,
+                                    pxCreatedTask, pxNewTCB,
+                                    pxTaskDefinition->xRegions );
+
+            prvAddNewTaskToReadyList( pxNewTCB );
+            xReturn = pdPASS;
         }
-        else
+    }
+
+    return xReturn;
+}
+
+#endif /* portUSING_MPU_WRAPPERS */
+/*-----------------------------------------------------------*/
+
+#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 )
+
+BaseType_t xTaskCreate(	TaskFunction_t pxTaskCode,
+                        const char* const pcName,		/*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+                        const configSTACK_DEPTH_TYPE usStackDepth,
+                        void* const pvParameters,
+                        UBaseType_t uxPriority,
+                        TaskHandle_t* const pxCreatedTask )
+{
+    TCB_t* pxNewTCB;
+    BaseType_t xReturn;
+
+    /* If the stack grows down then allocate the stack then the TCB so the stack
+    does not grow into the TCB.  Likewise if the stack grows up then allocate
+    the TCB then the stack. */
+#if( portSTACK_GROWTH > 0 )
+    {
+        /* Allocate space for the TCB.  Where the memory comes from depends on
+        the implementation of the port malloc function and whether or not static
+        allocation is being used. */
+        pxNewTCB = ( TCB_t* ) pvPortMalloc( sizeof( TCB_t ) );
+
+        if ( pxNewTCB != NULL )
         {
-            /* The stack was allocated dynamically.  Note this so it can be
-            deleted again if the task is deleted. */
-            pxNewTCB->xUsingStaticallyAllocatedStack = pdFALSE;
+            /* Allocate space for the stack used by the task being created.
+            The base of the stack memory stored in the TCB so the task can
+            be deleted later if required. */
+            pxNewTCB->pxStack = ( StackType_t* ) pvPortMalloc( ( ( ( size_t ) usStackDepth ) * sizeof( StackType_t ) ) );  /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
+
+            if ( pxNewTCB->pxStack == NULL )
+            {
+                /* Could not allocate the stack.  Delete the allocated TCB. */
+                vPortFree( pxNewTCB );
+                pxNewTCB = NULL;
+            }
         }
+    }
+#else /* portSTACK_GROWTH */
+    {
+        StackType_t* pxStack;
 
-#endif /* portUSING_MPU_WRAPPERS == 1 */
-        /* Calculate the top of stack address.  This depends on whether the
-        stack grows from high memory to low (as per the 80x86) or vice versa.
-        portSTACK_GROWTH is used to make the result positive or negative as
-        required by the port. */
-#if( portSTACK_GROWTH < 0 )
+        /* Allocate space for the stack used by the task being created. */
+        pxStack = ( StackType_t* ) pvPortMalloc( ( ( ( size_t ) usStackDepth ) * sizeof( StackType_t ) ) );  /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
+
+        if ( pxStack != NULL )
         {
-            pxTopOfStack = pxNewTCB->pxStack + ( usStackDepth - ( uint16_t ) 1 );
-            pxTopOfStack = ( StackType_t* ) ( ( ( portPOINTER_SIZE_TYPE ) pxTopOfStack ) & ( ~( ( portPOINTER_SIZE_TYPE ) portBYTE_ALIGNMENT_MASK ) ) );  /*lint !e923 MISRA exception.  Avoiding casts between pointers and integers is not practical.  Size differences accounted for using portPOINTER_SIZE_TYPE type. */
-            /* Check the alignment of the calculated top of stack is correct. */
-            configASSERT( ( ( ( portPOINTER_SIZE_TYPE ) pxTopOfStack & ( portPOINTER_SIZE_TYPE ) portBYTE_ALIGNMENT_MASK ) == 0UL ) );
+            /* Allocate space for the TCB. */
+            pxNewTCB = ( TCB_t* ) pvPortMalloc( sizeof( TCB_t ) );  /*lint !e961 MISRA exception as the casts are only redundant for some paths. */
+
+            if ( pxNewTCB != NULL )
+            {
+                /* Store the stack location in the TCB. */
+                pxNewTCB->pxStack = pxStack;
+            }
+            else
+            {
+                /* The stack cannot be used as the TCB was not created.  Free
+                it again. */
+                vPortFree( pxStack );
+            }
         }
-#else /* portSTACK_GROWTH */
+        else
         {
-            pxTopOfStack = pxNewTCB->pxStack;
-            /* Check the alignment of the stack buffer is correct. */
-            configASSERT( ( ( ( portPOINTER_SIZE_TYPE ) pxNewTCB->pxStack & ( portPOINTER_SIZE_TYPE ) portBYTE_ALIGNMENT_MASK ) == 0UL ) );
-            /* If we want to use stack checking on architectures that use
-            a positive stack growth direction then we also need to store the
-            other extreme of the stack space. */
-            pxNewTCB->pxEndOfStack = pxNewTCB->pxStack + ( usStackDepth - 1 );
+            pxNewTCB = NULL;
         }
+    }
 #endif /* portSTACK_GROWTH */
-        /* Setup the newly allocated TCB with the initial state of the task. */
-        prvInitialiseTCBVariables( pxNewTCB, pcName, uxPriority, xRegions, usStackDepth );
-        /* Initialize the TCB stack to look as if the task was already running,
-        but had been interrupted by the scheduler.  The return address is set
-        to the start of the task function. Once the stack has been initialised
-        the	top of stack variable is updated. */
-#if( portUSING_MPU_WRAPPERS == 1 )
+
+    if ( pxNewTCB != NULL )
+    {
+#if( tskSTATIC_AND_DYNAMIC_ALLOCATION_POSSIBLE != 0 ) /*lint !e731 Macro has been consolidated for readability reasons. */
         {
-            pxNewTCB->pxTopOfStack = pxPortInitialiseStack( pxTopOfStack, pxTaskCode, pvParameters, xRunPrivileged );
+            /* Tasks can be created statically or dynamically, so note this
+            task was created dynamically in case it is later deleted. */
+            pxNewTCB->ucStaticallyAllocated = tskDYNAMICALLY_ALLOCATED_STACK_AND_TCB;
         }
-#else /* portUSING_MPU_WRAPPERS */
+#endif /* configSUPPORT_STATIC_ALLOCATION */
+
+        prvInitialiseNewTask( pxTaskCode, pcName, ( uint32_t ) usStackDepth, pvParameters, uxPriority, pxCreatedTask, pxNewTCB, NULL );
+        prvAddNewTaskToReadyList( pxNewTCB );
+        xReturn = pdPASS;
+    }
+    else
+    {
+        xReturn = errCOULD_NOT_ALLOCATE_REQUIRED_MEMORY;
+    }
+
+    return xReturn;
+}
+
+#endif /* configSUPPORT_DYNAMIC_ALLOCATION */
+/*-----------------------------------------------------------*/
+
+static void prvInitialiseNewTask( 	TaskFunction_t pxTaskCode,
+                                    const char* const pcName,		/*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+                                    const uint32_t ulStackDepth,
+                                    void* const pvParameters,
+                                    UBaseType_t uxPriority,
+                                    TaskHandle_t* const pxCreatedTask,
+                                    TCB_t* pxNewTCB,
+                                    const MemoryRegion_t* const xRegions )
+{
+    StackType_t* pxTopOfStack;
+    UBaseType_t x;
+
+#if( portUSING_MPU_WRAPPERS == 1 )
+    /* Should the task be created in privileged mode? */
+    BaseType_t xRunPrivileged;
+
+    if ( ( uxPriority & portPRIVILEGE_BIT ) != 0U )
+    {
+        xRunPrivileged = pdTRUE;
+    }
+    else
+    {
+        xRunPrivileged = pdFALSE;
+    }
+
+    uxPriority &= ~portPRIVILEGE_BIT;
+#endif /* portUSING_MPU_WRAPPERS == 1 */
+
+    /* Avoid dependency on memset() if it is not required. */
+#if( tskSET_NEW_STACKS_TO_KNOWN_VALUE == 1 )
+    {
+        /* Fill the stack with a known value to assist debugging. */
+        ( void ) memset( pxNewTCB->pxStack, ( int ) tskSTACK_FILL_BYTE, ( size_t ) ulStackDepth * sizeof( StackType_t ) );
+    }
+#endif /* tskSET_NEW_STACKS_TO_KNOWN_VALUE */
+
+    /* Calculate the top of stack address.  This depends on whether the stack
+    grows from high memory to low (as per the 80x86) or vice versa.
+    portSTACK_GROWTH is used to make the result positive or negative as required
+    by the port. */
+#if( portSTACK_GROWTH < 0 )
+    {
+        pxTopOfStack = pxNewTCB->pxStack + ( ulStackDepth - ( uint32_t ) 1 );
+        pxTopOfStack = ( StackType_t* ) ( ( ( portPOINTER_SIZE_TYPE ) pxTopOfStack ) & ( ~( ( portPOINTER_SIZE_TYPE ) portBYTE_ALIGNMENT_MASK ) ) );  /*lint !e923 MISRA exception.  Avoiding casts between pointers and integers is not practical.  Size differences accounted for using portPOINTER_SIZE_TYPE type. */
+
+        /* Check the alignment of the calculated top of stack is correct. */
+        configASSERT( ( ( ( portPOINTER_SIZE_TYPE ) pxTopOfStack & ( portPOINTER_SIZE_TYPE ) portBYTE_ALIGNMENT_MASK ) == 0UL ) );
+
+#if( configRECORD_STACK_HIGH_ADDRESS == 1 )
         {
-            pxNewTCB->pxTopOfStack = pxPortInitialiseStack( pxTopOfStack, pxTaskCode, pvParameters );
+            /* Also record the stack's high address, which may assist
+            debugging. */
+            pxNewTCB->pxEndOfStack = pxTopOfStack;
         }
-#endif /* portUSING_MPU_WRAPPERS */
+#endif /* configRECORD_STACK_HIGH_ADDRESS */
+    }
+#else /* portSTACK_GROWTH */
+    {
+        pxTopOfStack = pxNewTCB->pxStack;
 
-        if ( ( void* ) pxCreatedTask != NULL )
+        /* Check the alignment of the stack buffer is correct. */
+        configASSERT( ( ( ( portPOINTER_SIZE_TYPE ) pxNewTCB->pxStack & ( portPOINTER_SIZE_TYPE ) portBYTE_ALIGNMENT_MASK ) == 0UL ) );
+
+        /* The other extreme of the stack space is required if stack checking is
+        performed. */
+        pxNewTCB->pxEndOfStack = pxNewTCB->pxStack + ( ulStackDepth - ( uint32_t ) 1 );
+    }
+#endif /* portSTACK_GROWTH */
+
+    /* Store the task name in the TCB. */
+    for ( x = ( UBaseType_t ) 0; x < ( UBaseType_t ) configMAX_TASK_NAME_LEN; x++ )
+    {
+        pxNewTCB->pcTaskName[ x ] = pcName[ x ];
+
+        /* Don't copy all configMAX_TASK_NAME_LEN if the string is shorter than
+        configMAX_TASK_NAME_LEN characters just in case the memory after the
+        string is not accessible (extremely unlikely). */
+        if ( pcName[ x ] == 0x00 )
         {
-            /* Pass the TCB out - in an anonymous way.  The calling function/
-            task can use this as a handle to delete the task later if
-            required.*/
-            *pxCreatedTask = ( TaskHandle_t ) pxNewTCB;
+            break;
         }
         else
         {
             mtCOVERAGE_TEST_MARKER();
         }
+    }
 
-        /* Ensure interrupts don't access the task lists while they are being
-        updated. */
-        taskENTER_CRITICAL();
+    /* Ensure the name string is terminated in the case that the string length
+    was greater or equal to configMAX_TASK_NAME_LEN. */
+    pxNewTCB->pcTaskName[ configMAX_TASK_NAME_LEN - 1 ] = '\0';
+
+    /* This is used as an array index so must ensure it's not too large.  First
+    remove the privilege bit if one is present. */
+    if ( uxPriority >= ( UBaseType_t ) configMAX_PRIORITIES )
+    {
+        uxPriority = ( UBaseType_t ) configMAX_PRIORITIES - ( UBaseType_t ) 1U;
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+
+    pxNewTCB->uxPriority = uxPriority;
+#if ( configUSE_MUTEXES == 1 )
+    {
+        pxNewTCB->uxBasePriority = uxPriority;
+        pxNewTCB->uxMutexesHeld = 0;
+    }
+#endif /* configUSE_MUTEXES */
+
+    vListInitialiseItem( &( pxNewTCB->xStateListItem ) );
+    vListInitialiseItem( &( pxNewTCB->xEventListItem ) );
+
+    /* Set the pxNewTCB as a link back from the ListItem_t.  This is so we can get
+    back to	the containing TCB from a generic item in a list. */
+    listSET_LIST_ITEM_OWNER( &( pxNewTCB->xStateListItem ), pxNewTCB );
+
+    /* Event lists are always in priority order. */
+    listSET_LIST_ITEM_VALUE( &( pxNewTCB->xEventListItem ), ( TickType_t ) configMAX_PRIORITIES - ( TickType_t ) uxPriority ); /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
+    listSET_LIST_ITEM_OWNER( &( pxNewTCB->xEventListItem ), pxNewTCB );
+
+#if ( portCRITICAL_NESTING_IN_TCB == 1 )
+    {
+        pxNewTCB->uxCriticalNesting = ( UBaseType_t ) 0U;
+    }
+#endif /* portCRITICAL_NESTING_IN_TCB */
+
+#if ( configUSE_APPLICATION_TASK_TAG == 1 )
+    {
+        pxNewTCB->pxTaskTag = NULL;
+    }
+#endif /* configUSE_APPLICATION_TASK_TAG */
+
+#if ( configGENERATE_RUN_TIME_STATS == 1 )
+    {
+        pxNewTCB->ulRunTimeCounter = 0UL;
+    }
+#endif /* configGENERATE_RUN_TIME_STATS */
+
+#if ( portUSING_MPU_WRAPPERS == 1 )
+    {
+        vPortStoreTaskMPUSettings( &( pxNewTCB->xMPUSettings ), xRegions, pxNewTCB->pxStack, ulStackDepth );
+    }
+#else
+    {
+        /* Avoid compiler warning about unreferenced parameter. */
+        ( void ) xRegions;
+    }
+#endif
+
+#if( configNUM_THREAD_LOCAL_STORAGE_POINTERS != 0 )
+    {
+        for ( x = 0; x < ( UBaseType_t ) configNUM_THREAD_LOCAL_STORAGE_POINTERS; x++ )
         {
-            uxCurrentNumberOfTasks++;
+            pxNewTCB->pvThreadLocalStoragePointers[ x ] = NULL;
+        }
+    }
+#endif
 
-            if ( pxCurrentTCB == NULL )
-            {
-                /* There are no other tasks, or all the other tasks are in
-                the suspended state - make this the current task. */
-                pxCurrentTCB =  pxNewTCB;
+#if ( configUSE_TASK_NOTIFICATIONS == 1 )
+    {
+        pxNewTCB->ulNotifiedValue = 0;
+        pxNewTCB->ucNotifyState = taskNOT_WAITING_NOTIFICATION;
+    }
+#endif
 
-                if ( uxCurrentNumberOfTasks == ( UBaseType_t ) 1 )
-                {
-                    /* This is the first task to be created so do the preliminary
-                    initialisation required.  We will not recover if this call
-                    fails, but we will report the failure. */
-                    prvInitialiseTaskLists();
-                }
-                else
-                {
-                    mtCOVERAGE_TEST_MARKER();
-                }
+#if ( configUSE_NEWLIB_REENTRANT == 1 )
+    {
+        /* Initialise this task's Newlib reent structure. */
+        _REENT_INIT_PTR( ( &( pxNewTCB->xNewLib_reent ) ) );
+    }
+#endif
+
+#if( INCLUDE_xTaskAbortDelay == 1 )
+    {
+        pxNewTCB->ucDelayAborted = pdFALSE;
+    }
+#endif
+
+    /* Initialize the TCB stack to look as if the task was already running,
+    but had been interrupted by the scheduler.  The return address is set
+    to the start of the task function. Once the stack has been initialised
+    the top of stack variable is updated. */
+#if( portUSING_MPU_WRAPPERS == 1 )
+    {
+        pxNewTCB->pxTopOfStack = pxPortInitialiseStack( pxTopOfStack, pxTaskCode, pvParameters, xRunPrivileged );
+    }
+#else /* portUSING_MPU_WRAPPERS */
+    {
+        pxNewTCB->pxTopOfStack = pxPortInitialiseStack( pxTopOfStack, pxTaskCode, pvParameters );
+    }
+#endif /* portUSING_MPU_WRAPPERS */
+
+    if ( ( void* ) pxCreatedTask != NULL )
+    {
+        /* Pass the handle out in an anonymous way.  The handle can be used to
+        change the created task's priority, delete the created task, etc.*/
+        *pxCreatedTask = ( TaskHandle_t ) pxNewTCB;
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+}
+/*-----------------------------------------------------------*/
+
+static void prvAddNewTaskToReadyList( TCB_t* pxNewTCB )
+{
+    /* Ensure interrupts don't access the task lists while the lists are being
+    updated. */
+    taskENTER_CRITICAL();
+    {
+        uxCurrentNumberOfTasks++;
+
+        if ( pxCurrentTCB == NULL )
+        {
+            /* There are no other tasks, or all the other tasks are in
+            the suspended state - make this the current task. */
+            pxCurrentTCB = pxNewTCB;
+
+            if ( uxCurrentNumberOfTasks == ( UBaseType_t ) 1 )
+            {
+                /* This is the first task to be created so do the preliminary
+                initialisation required.  We will not recover if this call
+                fails, but we will report the failure. */
+                prvInitialiseTaskLists();
             }
             else
             {
-                /* If the scheduler is not already running, make this task the
-                current task if it is the highest priority task to be created
-                so far. */
-                if ( xSchedulerRunning == pdFALSE )
+                mtCOVERAGE_TEST_MARKER();
+            }
+        }
+        else
+        {
+            /* If the scheduler is not already running, make this task the
+            current task if it is the highest priority task to be created
+            so far. */
+            if ( xSchedulerRunning == pdFALSE )
+            {
+                if ( pxCurrentTCB->uxPriority <= pxNewTCB->uxPriority )
                 {
-                    if ( pxCurrentTCB->uxPriority <= uxPriority )
-                    {
-                        pxCurrentTCB = pxNewTCB;
-                    }
-                    else
-                    {
-                        mtCOVERAGE_TEST_MARKER();
-                    }
+                    pxCurrentTCB = pxNewTCB;
                 }
                 else
                 {
                     mtCOVERAGE_TEST_MARKER();
                 }
             }
-
-            uxTaskNumber++;
-#if ( configUSE_TRACE_FACILITY == 1 )
+            else
             {
-                /* Add a counter into the TCB for tracing only. */
-                pxNewTCB->uxTCBNumber = uxTaskNumber;
+                mtCOVERAGE_TEST_MARKER();
             }
-#endif /* configUSE_TRACE_FACILITY */
-            traceTASK_CREATE( pxNewTCB );
-            prvAddTaskToReadyList( pxNewTCB );
-            xReturn = pdPASS;
-            portSETUP_TCB( pxNewTCB );
         }
-        taskEXIT_CRITICAL();
-    }
-    else
-    {
-        xReturn = errCOULD_NOT_ALLOCATE_REQUIRED_MEMORY;
-        traceTASK_CREATE_FAILED();
+
+        uxTaskNumber++;
+
+#if ( configUSE_TRACE_FACILITY == 1 )
+        {
+            /* Add a counter into the TCB for tracing only. */
+            pxNewTCB->uxTCBNumber = uxTaskNumber;
+        }
+#endif /* configUSE_TRACE_FACILITY */
+        traceTASK_CREATE( pxNewTCB );
+
+        prvAddTaskToReadyList( pxNewTCB );
+
+        portSETUP_TCB( pxNewTCB );
     }
+    taskEXIT_CRITICAL();
 
-    if ( xReturn == pdPASS )
+    if ( xSchedulerRunning != pdFALSE )
     {
-        if ( xSchedulerRunning != pdFALSE )
+        /* If the created task is of a higher priority than the current task
+        then it should run now. */
+        if ( pxCurrentTCB->uxPriority < pxNewTCB->uxPriority )
         {
-            /* If the created task is of a higher priority than the current task
-            then it should run now. */
-            if ( pxCurrentTCB->uxPriority < uxPriority )
-            {
-                taskYIELD_IF_USING_PREEMPTION();
-            }
-            else
-            {
-                mtCOVERAGE_TEST_MARKER();
-            }
+            taskYIELD_IF_USING_PREEMPTION();
         }
         else
         {
             mtCOVERAGE_TEST_MARKER();
         }
     }
-
-    return xReturn;
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
 }
 /*-----------------------------------------------------------*/
 
@@ -737,17 +1109,15 @@ BaseType_t xTaskGenericCreate( TaskFunction_t pxTaskCode, const char* const pcNa
 void vTaskDelete( TaskHandle_t xTaskToDelete )
 {
     TCB_t* pxTCB;
+
     taskENTER_CRITICAL();
     {
         /* If null is passed in here then it is the calling task that is
         being deleted. */
         pxTCB = prvGetTCBFromHandle( xTaskToDelete );
 
-        /* Remove task from the ready list and place in the	termination list.
-        This will stop the task from be scheduled.  The idle task will check
-        the termination list and free up any memory allocated by the
-        scheduler for the TCB and stack. */
-        if ( uxListRemove( &( pxTCB->xGenericListItem ) ) == ( UBaseType_t ) 0 )
+        /* Remove task from the ready list. */
+        if ( uxListRemove( &( pxTCB->xStateListItem ) ) == ( UBaseType_t ) 0 )
         {
             taskRESET_READY_PRIORITY( pxTCB->uxPriority );
         }
@@ -766,14 +1136,43 @@ void vTaskDelete( TaskHandle_t xTaskToDelete )
             mtCOVERAGE_TEST_MARKER();
         }
 
-        vListInsertEnd( &xTasksWaitingTermination, &( pxTCB->xGenericListItem ) );
-        /* Increment the ucTasksDeleted variable so the idle task knows
-        there is a task that has been deleted and that it should therefore
-        check the xTasksWaitingTermination list. */
-        ++uxTasksDeleted;
-        /* Increment the uxTaskNumberVariable also so kernel aware debuggers
-        can detect that the task lists need re-generating. */
+        /* Increment the uxTaskNumber also so kernel aware debuggers can
+        detect that the task lists need re-generating.  This is done before
+        portPRE_TASK_DELETE_HOOK() as in the Windows port that macro will
+        not return. */
         uxTaskNumber++;
+
+        if ( pxTCB == pxCurrentTCB )
+        {
+            /* A task is deleting itself.  This cannot complete within the
+            task itself, as a context switch to another task is required.
+            Place the task in the termination list.  The idle task will
+            check the termination list and free up any memory allocated by
+            the scheduler for the TCB and stack of the deleted task. */
+            vListInsertEnd( &xTasksWaitingTermination, &( pxTCB->xStateListItem ) );
+
+            /* Increment the ucTasksDeleted variable so the idle task knows
+            there is a task that has been deleted and that it should therefore
+            check the xTasksWaitingTermination list. */
+            ++uxDeletedTasksWaitingCleanUp;
+
+            /* The pre-delete hook is primarily for the Windows simulator,
+            in which Windows specific clean up operations are performed,
+            after which it is not possible to yield away from this task -
+            hence xYieldPending is used to latch that a context switch is
+            required. */
+            portPRE_TASK_DELETE_HOOK( pxTCB, &xYieldPending );
+        }
+        else
+        {
+            --uxCurrentNumberOfTasks;
+            prvDeleteTCB( pxTCB );
+
+            /* Reset the next expected unblock time in case it referred to
+            the task that has just been deleted. */
+            prvResetNextTaskUnblockTime();
+        }
+
         traceTASK_DELETE( pxTCB );
     }
     taskEXIT_CRITICAL();
@@ -785,23 +1184,11 @@ void vTaskDelete( TaskHandle_t xTaskToDelete )
         if ( pxTCB == pxCurrentTCB )
         {
             configASSERT( uxSchedulerSuspended == 0 );
-            /* The pre-delete hook is primarily for the Windows simulator,
-            in which Windows specific clean up operations are performed,
-            after which it is not possible to yield away from this task -
-            hence xYieldPending is used to latch that a context switch is
-            required. */
-            portPRE_TASK_DELETE_HOOK( pxTCB, &xYieldPending );
             portYIELD_WITHIN_API();
         }
         else
         {
-            /* Reset the next expected unblock time in case it referred to
-            the task that has just been deleted. */
-            taskENTER_CRITICAL();
-            {
-                prvResetNextTaskUnblockTime();
-            }
-            taskEXIT_CRITICAL();
+            mtCOVERAGE_TEST_MARKER();
         }
     }
 }
@@ -815,14 +1202,17 @@ void vTaskDelayUntil( TickType_t* const pxPreviousWakeTime, const TickType_t xTi
 {
     TickType_t xTimeToWake;
     BaseType_t xAlreadyYielded, xShouldDelay = pdFALSE;
+
     configASSERT( pxPreviousWakeTime );
     configASSERT( ( xTimeIncrement > 0U ) );
     configASSERT( uxSchedulerSuspended == 0 );
+
     vTaskSuspendAll();
     {
         /* Minor optimisation.  The tick count cannot change in this
         block. */
         const TickType_t xConstTickCount = xTickCount;
+
         /* Generate the tick time at which the task wants to wake. */
         xTimeToWake = *pxPreviousWakeTime + xTimeIncrement;
 
@@ -862,23 +1252,11 @@ void vTaskDelayUntil( TickType_t* const pxPreviousWakeTime, const TickType_t xTi
 
         if ( xShouldDelay != pdFALSE )
         {
-            traceTASK_DELAY_UNTIL();
-
-            /* Remove the task from the ready list before adding it to the
-            blocked list as the same list item is used for both lists. */
-            if ( uxListRemove( &( pxCurrentTCB->xGenericListItem ) ) == ( UBaseType_t ) 0 )
-            {
-                /* The current task must be in a ready list, so there is
-                no need to check, and the port reset macro can be called
-                directly. */
-                portRESET_READY_PRIORITY( pxCurrentTCB->uxPriority, uxTopReadyPriority );
-            }
-            else
-            {
-                mtCOVERAGE_TEST_MARKER();
-            }
+            traceTASK_DELAY_UNTIL( xTimeToWake );
 
-            prvAddCurrentTaskToDelayedList( xTimeToWake );
+            /* prvAddCurrentTaskToDelayedList() needs the block time, not
+            the time to wake, so subtract the current tick count. */
+            prvAddCurrentTaskToDelayedList( xTimeToWake - xConstTickCount, pdFALSE );
         }
         else
         {
@@ -906,7 +1284,6 @@ void vTaskDelayUntil( TickType_t* const pxPreviousWakeTime, const TickType_t xTi
 
 void vTaskDelay( const TickType_t xTicksToDelay )
 {
-    TickType_t xTimeToWake;
     BaseType_t xAlreadyYielded = pdFALSE;
 
     /* A delay time of zero just forces a reschedule. */
@@ -916,6 +1293,7 @@ void vTaskDelay( const TickType_t xTicksToDelay )
         vTaskSuspendAll();
         {
             traceTASK_DELAY();
+
             /* A task that is removed from the event list while the
             scheduler is suspended will not get placed in the ready
             list or removed from the blocked list until the scheduler
@@ -923,26 +1301,7 @@ void vTaskDelay( const TickType_t xTicksToDelay )
 
             This task cannot be in an event list as it is the currently
             executing task. */
-            /* Calculate the time to wake - this may overflow but this is
-            not a problem. */
-            xTimeToWake = xTickCount + xTicksToDelay;
-
-            /* We must remove ourselves from the ready list before adding
-            ourselves to the blocked list as the same list item is used for
-            both lists. */
-            if ( uxListRemove( &( pxCurrentTCB->xGenericListItem ) ) == ( UBaseType_t ) 0 )
-            {
-                /* The current task must be in a ready list, so there is
-                no need to check, and the port reset macro can be called
-                directly. */
-                portRESET_READY_PRIORITY( pxCurrentTCB->uxPriority, uxTopReadyPriority );
-            }
-            else
-            {
-                mtCOVERAGE_TEST_MARKER();
-            }
-
-            prvAddCurrentTaskToDelayedList( xTimeToWake );
+            prvAddCurrentTaskToDelayedList( xTicksToDelay, pdFALSE );
         }
         xAlreadyYielded = xTaskResumeAll();
     }
@@ -966,13 +1325,14 @@ void vTaskDelay( const TickType_t xTicksToDelay )
 #endif /* INCLUDE_vTaskDelay */
 /*-----------------------------------------------------------*/
 
-#if ( INCLUDE_eTaskGetState == 1 )
+#if( ( INCLUDE_eTaskGetState == 1 ) || ( configUSE_TRACE_FACILITY == 1 ) )
 
 eTaskState eTaskGetState( TaskHandle_t xTask )
 {
     eTaskState eReturn;
     List_t* pxStateList;
     const TCB_t* const pxTCB = ( TCB_t* ) xTask;
+
     configASSERT( pxTCB );
 
     if ( pxTCB == pxCurrentTCB )
@@ -984,7 +1344,7 @@ eTaskState eTaskGetState( TaskHandle_t xTask )
     {
         taskENTER_CRITICAL();
         {
-            pxStateList = ( List_t* ) listLIST_ITEM_CONTAINER( &( pxTCB->xGenericListItem ) );
+            pxStateList = ( List_t* ) listLIST_ITEM_CONTAINER( &( pxTCB->xStateListItem ) );
         }
         taskEXIT_CRITICAL();
 
@@ -1012,15 +1372,18 @@ eTaskState eTaskGetState( TaskHandle_t xTask )
         }
 
 #endif
+
 #if ( INCLUDE_vTaskDelete == 1 )
-        else if ( pxStateList == &xTasksWaitingTermination )
+        else if ( ( pxStateList == &xTasksWaitingTermination ) || ( pxStateList == NULL ) )
         {
             /* The task being queried is referenced from the deleted
-            tasks list. */
+            tasks list, or it is not referenced from any lists at
+            all. */
             eReturn = eDeleted;
         }
 
 #endif
+
         else /*lint !e525 Negative indentation is intended to make use of pre-processor clearer. */
         {
             /* If the task is not in any other state, it must be in the
@@ -1041,6 +1404,7 @@ UBaseType_t uxTaskPriorityGet( TaskHandle_t xTask )
 {
     TCB_t* pxTCB;
     UBaseType_t uxReturn;
+
     taskENTER_CRITICAL();
     {
         /* If null is passed in here then it is the priority of the that
@@ -1049,6 +1413,7 @@ UBaseType_t uxTaskPriorityGet( TaskHandle_t xTask )
         uxReturn = pxTCB->uxPriority;
     }
     taskEXIT_CRITICAL();
+
     return uxReturn;
 }
 
@@ -1061,6 +1426,7 @@ UBaseType_t uxTaskPriorityGetFromISR( TaskHandle_t xTask )
 {
     TCB_t* pxTCB;
     UBaseType_t uxReturn, uxSavedInterruptState;
+
     /* RTOS ports that support interrupt nesting have the concept of a
     maximum	system call (or maximum API call) interrupt priority.
     Interrupts that are	above the maximum system call priority are keep
@@ -1078,6 +1444,7 @@ UBaseType_t uxTaskPriorityGetFromISR( TaskHandle_t xTask )
     provided on the following link:
     http://www.freertos.org/RTOS-Cortex-M3-M4.html */
     portASSERT_IF_INTERRUPT_PRIORITY_INVALID();
+
     uxSavedInterruptState = portSET_INTERRUPT_MASK_FROM_ISR();
     {
         /* If null is passed in here then it is the priority of the calling
@@ -1086,6 +1453,7 @@ UBaseType_t uxTaskPriorityGetFromISR( TaskHandle_t xTask )
         uxReturn = pxTCB->uxPriority;
     }
     portCLEAR_INTERRUPT_MASK_FROM_ISR( uxSavedInterruptState );
+
     return uxReturn;
 }
 
@@ -1099,6 +1467,7 @@ void vTaskPrioritySet( TaskHandle_t xTask, UBaseType_t uxNewPriority )
     TCB_t* pxTCB;
     UBaseType_t uxCurrentBasePriority, uxPriorityUsedOnEntry;
     BaseType_t xYieldRequired = pdFALSE;
+
     configASSERT( ( uxNewPriority < configMAX_PRIORITIES ) );
 
     /* Ensure the new priority is valid. */
@@ -1116,7 +1485,9 @@ void vTaskPrioritySet( TaskHandle_t xTask, UBaseType_t uxNewPriority )
         /* If null is passed in here then it is the priority of the calling
         task that is being changed. */
         pxTCB = prvGetTCBFromHandle( xTask );
+
         traceTASK_PRIORITY_SET( pxTCB, uxNewPriority );
+
 #if ( configUSE_MUTEXES == 1 )
         {
             uxCurrentBasePriority = pxTCB->uxBasePriority;
@@ -1172,6 +1543,7 @@ void vTaskPrioritySet( TaskHandle_t xTask, UBaseType_t uxNewPriority )
             before its uxPriority member is changed so the
             taskRESET_READY_PRIORITY() macro can function correctly. */
             uxPriorityUsedOnEntry = pxTCB->uxPriority;
+
 #if ( configUSE_MUTEXES == 1 )
             {
                 /* Only change the priority being used if the task is not
@@ -1206,15 +1578,15 @@ void vTaskPrioritySet( TaskHandle_t xTask, UBaseType_t uxNewPriority )
             }
 
             /* If the task is in the blocked or suspended list we need do
-            nothing more than change it's priority variable. However, if
+            nothing more than change its priority variable. However, if
             the task is in a ready list it needs to be removed and placed
             in the list appropriate to its new priority. */
-            if ( listIS_CONTAINED_WITHIN( &( pxReadyTasksLists[ uxPriorityUsedOnEntry ] ), &( pxTCB->xGenericListItem ) ) != pdFALSE )
+            if ( listIS_CONTAINED_WITHIN( &( pxReadyTasksLists[ uxPriorityUsedOnEntry ] ), &( pxTCB->xStateListItem ) ) != pdFALSE )
             {
-                /* The task is currently in its ready list - remove before adding
-                it to it's new ready list.  As we are in a critical section we
-                can do this even if the scheduler is suspended. */
-                if ( uxListRemove( &( pxTCB->xGenericListItem ) ) == ( UBaseType_t ) 0 )
+                /* The task is currently in its ready list - remove before
+                adding it to it's new ready list.  As we are in a critical
+                section we can do this even if the scheduler is suspended. */
+                if ( uxListRemove( &( pxTCB->xStateListItem ) ) == ( UBaseType_t ) 0 )
                 {
                     /* It is known that the task is in its ready list so
                     there is no need to check again and the port level
@@ -1233,7 +1605,7 @@ void vTaskPrioritySet( TaskHandle_t xTask, UBaseType_t uxNewPriority )
                 mtCOVERAGE_TEST_MARKER();
             }
 
-            if ( xYieldRequired == pdTRUE )
+            if ( xYieldRequired != pdFALSE )
             {
                 taskYIELD_IF_USING_PREEMPTION();
             }
@@ -1258,16 +1630,18 @@ void vTaskPrioritySet( TaskHandle_t xTask, UBaseType_t uxNewPriority )
 void vTaskSuspend( TaskHandle_t xTaskToSuspend )
 {
     TCB_t* pxTCB;
+
     taskENTER_CRITICAL();
     {
         /* If null is passed in here then it is the running task that is
         being suspended. */
         pxTCB = prvGetTCBFromHandle( xTaskToSuspend );
+
         traceTASK_SUSPEND( pxTCB );
 
         /* Remove task from the ready/delayed list and place in the
         suspended list. */
-        if ( uxListRemove( &( pxTCB->xGenericListItem ) ) == ( UBaseType_t ) 0 )
+        if ( uxListRemove( &( pxTCB->xStateListItem ) ) == ( UBaseType_t ) 0 )
         {
             taskRESET_READY_PRIORITY( pxTCB->uxPriority );
         }
@@ -1286,10 +1660,36 @@ void vTaskSuspend( TaskHandle_t xTaskToSuspend )
             mtCOVERAGE_TEST_MARKER();
         }
 
-        vListInsertEnd( &xSuspendedTaskList, &( pxTCB->xGenericListItem ) );
+        vListInsertEnd( &xSuspendedTaskList, &( pxTCB->xStateListItem ) );
+
+#if( configUSE_TASK_NOTIFICATIONS == 1 )
+        {
+            if ( pxTCB->ucNotifyState == taskWAITING_NOTIFICATION )
+            {
+                /* The task was blocked to wait for a notification, but is
+                now suspended, so no notification was received. */
+                pxTCB->ucNotifyState = taskNOT_WAITING_NOTIFICATION;
+            }
+        }
+#endif
     }
     taskEXIT_CRITICAL();
 
+    if ( xSchedulerRunning != pdFALSE )
+    {
+        /* Reset the next expected unblock time in case it referred to the
+        task that is now in the Suspended state. */
+        taskENTER_CRITICAL();
+        {
+            prvResetNextTaskUnblockTime();
+        }
+        taskEXIT_CRITICAL();
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+
     if ( pxTCB == pxCurrentTCB )
     {
         if ( xSchedulerRunning != pdFALSE )
@@ -1319,21 +1719,7 @@ void vTaskSuspend( TaskHandle_t xTaskToSuspend )
     }
     else
     {
-        if ( xSchedulerRunning != pdFALSE )
-        {
-            /* A task other than the currently running task was suspended,
-            reset the next expected unblock time in case it referred to the
-            task that is now in the Suspended state. */
-            taskENTER_CRITICAL();
-            {
-                prvResetNextTaskUnblockTime();
-            }
-            taskEXIT_CRITICAL();
-        }
-        else
-        {
-            mtCOVERAGE_TEST_MARKER();
-        }
+        mtCOVERAGE_TEST_MARKER();
     }
 }
 
@@ -1346,20 +1732,22 @@ static BaseType_t prvTaskIsTaskSuspended( const TaskHandle_t xTask )
 {
     BaseType_t xReturn = pdFALSE;
     const TCB_t* const pxTCB = ( TCB_t* ) xTask;
+
     /* Accesses xPendingReadyList so must be called from a critical
     section. */
+
     /* It does not make sense to check if the calling task is suspended. */
     configASSERT( xTask );
 
     /* Is the task being resumed actually in the suspended list? */
-    if ( listIS_CONTAINED_WITHIN( &xSuspendedTaskList, &( pxTCB->xGenericListItem ) ) != pdFALSE )
+    if ( listIS_CONTAINED_WITHIN( &xSuspendedTaskList, &( pxTCB->xStateListItem ) ) != pdFALSE )
     {
         /* Has the task already been resumed from within an ISR? */
         if ( listIS_CONTAINED_WITHIN( &xPendingReadyList, &( pxTCB->xEventListItem ) ) == pdFALSE )
         {
             /* Is it in the suspended list because it is in the	Suspended
             state, or because is is blocked with no timeout? */
-            if ( listIS_CONTAINED_WITHIN( NULL, &( pxTCB->xEventListItem ) ) != pdFALSE )
+            if ( listIS_CONTAINED_WITHIN( NULL, &( pxTCB->xEventListItem ) ) != pdFALSE ) /*lint !e961.  The cast is only redundant when NULL is used. */
             {
                 xReturn = pdTRUE;
             }
@@ -1389,6 +1777,7 @@ static BaseType_t prvTaskIsTaskSuspended( const TaskHandle_t xTask )
 void vTaskResume( TaskHandle_t xTaskToResume )
 {
     TCB_t* const pxTCB = ( TCB_t* ) xTaskToResume;
+
     /* It does not make sense to resume the calling task. */
     configASSERT( xTaskToResume );
 
@@ -1398,15 +1787,16 @@ void vTaskResume( TaskHandle_t xTaskToResume )
     {
         taskENTER_CRITICAL();
         {
-            if ( prvTaskIsTaskSuspended( pxTCB ) == pdTRUE )
+            if ( prvTaskIsTaskSuspended( pxTCB ) != pdFALSE )
             {
                 traceTASK_RESUME( pxTCB );
-                /* As we are in a critical section we can access the ready
-                lists even if the scheduler is suspended. */
-                ( void ) uxListRemove(  &( pxTCB->xGenericListItem ) );
+
+                /* The ready list can be accessed even if the scheduler is
+                suspended because this is inside a critical section. */
+                ( void ) uxListRemove(  &( pxTCB->xStateListItem ) );
                 prvAddTaskToReadyList( pxTCB );
 
-                /* We may have just resumed a higher priority task. */
+                /* A higher priority task may have just been resumed. */
                 if ( pxTCB->uxPriority >= pxCurrentTCB->uxPriority )
                 {
                     /* This yield may not cause the task just resumed to run,
@@ -1443,7 +1833,9 @@ BaseType_t xTaskResumeFromISR( TaskHandle_t xTaskToResume )
     BaseType_t xYieldRequired = pdFALSE;
     TCB_t* const pxTCB = ( TCB_t* ) xTaskToResume;
     UBaseType_t uxSavedInterruptStatus;
+
     configASSERT( xTaskToResume );
+
     /* RTOS ports that support interrupt nesting have the concept of a
     maximum	system call (or maximum API call) interrupt priority.
     Interrupts that are	above the maximum system call priority are keep
@@ -1461,9 +1853,10 @@ BaseType_t xTaskResumeFromISR( TaskHandle_t xTaskToResume )
     provided on the following link:
     http://www.freertos.org/RTOS-Cortex-M3-M4.html */
     portASSERT_IF_INTERRUPT_PRIORITY_INVALID();
+
     uxSavedInterruptStatus = portSET_INTERRUPT_MASK_FROM_ISR();
     {
-        if ( prvTaskIsTaskSuspended( pxTCB ) == pdTRUE )
+        if ( prvTaskIsTaskSuspended( pxTCB ) != pdFALSE )
         {
             traceTASK_RESUME_FROM_ISR( pxTCB );
 
@@ -1481,7 +1874,7 @@ BaseType_t xTaskResumeFromISR( TaskHandle_t xTaskToResume )
                     mtCOVERAGE_TEST_MARKER();
                 }
 
-                ( void ) uxListRemove(  &( pxTCB->xGenericListItem ) );
+                ( void ) uxListRemove( &( pxTCB->xStateListItem ) );
                 prvAddTaskToReadyList( pxTCB );
             }
             else
@@ -1498,6 +1891,7 @@ BaseType_t xTaskResumeFromISR( TaskHandle_t xTaskToResume )
         }
     }
     portCLEAR_INTERRUPT_MASK_FROM_ISR( uxSavedInterruptStatus );
+
     return xYieldRequired;
 }
 
@@ -1507,19 +1901,46 @@ BaseType_t xTaskResumeFromISR( TaskHandle_t xTaskToResume )
 void vTaskStartScheduler( void )
 {
     BaseType_t xReturn;
+
     /* Add the idle task at the lowest priority. */
-#if ( INCLUDE_xTaskGetIdleTaskHandle == 1 )
-    {
-        /* Create the idle task, storing its handle in xIdleTaskHandle so it can
-        be returned by the xTaskGetIdleTaskHandle() function. */
-        xReturn = xTaskCreate( prvIdleTask, "IDLE", tskIDLE_STACK_SIZE, ( void* ) NULL, ( tskIDLE_PRIORITY | portPRIVILEGE_BIT ), &xIdleTaskHandle );  /*lint !e961 MISRA exception, justified as it is not a redundant explicit cast to all supported compilers. */
+#if( configSUPPORT_STATIC_ALLOCATION == 1 )
+    {
+        StaticTask_t* pxIdleTaskTCBBuffer = NULL;
+        StackType_t* pxIdleTaskStackBuffer = NULL;
+        uint32_t ulIdleTaskStackSize;
+
+        /* The Idle task is created using user provided RAM - obtain the
+        address of the RAM then create the idle task. */
+        vApplicationGetIdleTaskMemory( &pxIdleTaskTCBBuffer, &pxIdleTaskStackBuffer, &ulIdleTaskStackSize );
+        xIdleTaskHandle = xTaskCreateStatic(	prvIdleTask,
+                                                configIDLE_TASK_NAME,
+                                                ulIdleTaskStackSize,
+                                                ( void* ) NULL,  /*lint !e961.  The cast is not redundant for all compilers. */
+                                                ( tskIDLE_PRIORITY | portPRIVILEGE_BIT ),
+                                                pxIdleTaskStackBuffer,
+                                                pxIdleTaskTCBBuffer ); /*lint !e961 MISRA exception, justified as it is not a redundant explicit cast to all supported compilers. */
+
+        if ( xIdleTaskHandle != NULL )
+        {
+            xReturn = pdPASS;
+        }
+        else
+        {
+            xReturn = pdFAIL;
+        }
     }
 #else
     {
-        /* Create the idle task without storing its handle. */
-        xReturn = xTaskCreate( prvIdleTask, "IDLE", tskIDLE_STACK_SIZE, ( void* ) NULL, ( tskIDLE_PRIORITY | portPRIVILEGE_BIT ), NULL );   /*lint !e961 MISRA exception, justified as it is not a redundant explicit cast to all supported compilers. */
+        /* The Idle task is being created using dynamically allocated RAM. */
+        xReturn = xTaskCreate(	prvIdleTask,
+                                configIDLE_TASK_NAME,
+                                configMINIMAL_STACK_SIZE,
+                                ( void* ) NULL,
+                                ( tskIDLE_PRIORITY | portPRIVILEGE_BIT ),
+                                &xIdleTaskHandle ); /*lint !e961 MISRA exception, justified as it is not a redundant explicit cast to all supported compilers. */
     }
-#endif /* INCLUDE_xTaskGetIdleTaskHandle */
+#endif /* configSUPPORT_STATIC_ALLOCATION */
+
 #if ( configUSE_TIMERS == 1 )
     {
         if ( xReturn == pdPASS )
@@ -1535,12 +1956,22 @@ void vTaskStartScheduler( void )
 
     if ( xReturn == pdPASS )
     {
+        /* freertos_tasks_c_additions_init() should only be called if the user
+        definable macro FREERTOS_TASKS_C_ADDITIONS_INIT() is defined, as that is
+        the only macro called by the function. */
+#ifdef FREERTOS_TASKS_C_ADDITIONS_INIT
+        {
+            freertos_tasks_c_additions_init();
+        }
+#endif
+
         /* Interrupts are turned off here, to ensure a tick does not occur
         before or during the call to xPortStartScheduler().  The stacks of
         the created tasks contain a status word with interrupts switched on
         so interrupts will automatically get re-enabled when the first task
         starts to run. */
         portDISABLE_INTERRUPTS();
+
 #if ( configUSE_NEWLIB_REENTRANT == 1 )
         {
             /* Switch Newlib's _impure_ptr variable to point to the _reent
@@ -1548,12 +1979,17 @@ void vTaskStartScheduler( void )
             _impure_ptr = &( pxCurrentTCB->xNewLib_reent );
         }
 #endif /* configUSE_NEWLIB_REENTRANT */
+
         xNextTaskUnblockTime = portMAX_DELAY;
         xSchedulerRunning = pdTRUE;
         xTickCount = ( TickType_t ) 0U;
+
         /* If configGENERATE_RUN_TIME_STATS is defined then the following
         macro must be defined to configure the timer/counter used to generate
-        the run time counter time base. */
+        the run time counter time base.   NOTE:  If configGENERATE_RUN_TIME_STATS
+        is set to 0 and the following line fails to build then ensure you do not
+        have portCONFIGURE_TIMER_FOR_RUN_TIME_STATS() defined in your
+        FreeRTOSConfig.h file. */
         portCONFIGURE_TIMER_FOR_RUN_TIME_STATS();
 
         /* Setting up the timer tick is hardware specific and thus in the
@@ -1573,8 +2009,12 @@ void vTaskStartScheduler( void )
         /* This line will only be reached if the kernel could not be started,
         because there was not enough FreeRTOS heap to create the idle task
         or the timer task. */
-        configASSERT( xReturn );
+        configASSERT( xReturn != errCOULD_NOT_ALLOCATE_REQUIRED_MEMORY );
     }
+
+    /* Prevent compiler warnings if INCLUDE_xTaskGetIdleTaskHandle is set to 0,
+    meaning xIdleTaskHandle is not used anywhere else. */
+    ( void ) xIdleTaskHandle;
 }
 /*-----------------------------------------------------------*/
 
@@ -1604,6 +2044,34 @@ void vTaskSuspendAll( void )
 static TickType_t prvGetExpectedIdleTime( void )
 {
     TickType_t xReturn;
+    UBaseType_t uxHigherPriorityReadyTasks = pdFALSE;
+
+    /* uxHigherPriorityReadyTasks takes care of the case where
+    configUSE_PREEMPTION is 0, so there may be tasks above the idle priority
+    task that are in the Ready state, even though the idle task is
+    running. */
+#if( configUSE_PORT_OPTIMISED_TASK_SELECTION == 0 )
+    {
+        if ( uxTopReadyPriority > tskIDLE_PRIORITY )
+        {
+            uxHigherPriorityReadyTasks = pdTRUE;
+        }
+    }
+#else
+    {
+        const UBaseType_t uxLeastSignificantBit = ( UBaseType_t ) 0x01;
+
+        /* When port optimised task selection is used the uxTopReadyPriority
+        variable is used as a bit map.  If bits other than the least
+        significant bit are set then there are tasks that have a priority
+        above the idle priority that are in the Ready state.  This takes
+        care of the case where the co-operative scheduler is in use. */
+        if ( uxTopReadyPriority > uxLeastSignificantBit )
+        {
+            uxHigherPriorityReadyTasks = pdTRUE;
+        }
+    }
+#endif
 
     if ( pxCurrentTCB->uxPriority > tskIDLE_PRIORITY )
     {
@@ -1616,6 +2084,13 @@ static TickType_t prvGetExpectedIdleTime( void )
         processed. */
         xReturn = 0;
     }
+    else if ( uxHigherPriorityReadyTasks != pdFALSE )
+    {
+        /* There are tasks in the Ready state that have a priority above the
+        idle priority.  This path can only be reached if
+        configUSE_PREEMPTION is 0. */
+        xReturn = 0;
+    }
     else
     {
         xReturn = xNextTaskUnblockTime - xTickCount;
@@ -1629,11 +2104,13 @@ static TickType_t prvGetExpectedIdleTime( void )
 
 BaseType_t xTaskResumeAll( void )
 {
-    TCB_t* pxTCB;
+    TCB_t* pxTCB = NULL;
     BaseType_t xAlreadyYielded = pdFALSE;
+
     /* If uxSchedulerSuspended is zero then this function does not match a
     previous call to vTaskSuspendAll(). */
     configASSERT( uxSchedulerSuspended );
+
     /* It is possible that an ISR caused a task to be removed from an event
     list while the scheduler was suspended.  If this was the case then the
     removed task will have been added to the xPendingReadyList.  Once the
@@ -1653,7 +2130,7 @@ BaseType_t xTaskResumeAll( void )
                 {
                     pxTCB = ( TCB_t* ) listGET_OWNER_OF_HEAD_ENTRY( ( &xPendingReadyList ) );
                     ( void ) uxListRemove( &( pxTCB->xEventListItem ) );
-                    ( void ) uxListRemove( &( pxTCB->xGenericListItem ) );
+                    ( void ) uxListRemove( &( pxTCB->xStateListItem ) );
                     prvAddTaskToReadyList( pxTCB );
 
                     /* If the moved task has a priority higher than the current
@@ -1668,32 +2145,50 @@ BaseType_t xTaskResumeAll( void )
                     }
                 }
 
+                if ( pxTCB != NULL )
+                {
+                    /* A task was unblocked while the scheduler was suspended,
+                    which may have prevented the next unblock time from being
+                    re-calculated, in which case re-calculate it now.  Mainly
+                    important for low power tickless implementations, where
+                    this can prevent an unnecessary exit from low power
+                    state. */
+                    prvResetNextTaskUnblockTime();
+                }
+
                 /* If any ticks occurred while the scheduler was suspended then
                 they should be processed now.  This ensures the tick count does
                 not	slip, and that any delayed tasks are resumed at the correct
                 time. */
-                if ( uxPendedTicks > ( UBaseType_t ) 0U )
                 {
-                    while ( uxPendedTicks > ( UBaseType_t ) 0U )
+                    UBaseType_t uxPendedCounts = uxPendedTicks; /* Non-volatile copy. */
+
+                    if ( uxPendedCounts > ( UBaseType_t ) 0U )
                     {
-                        if ( xTaskIncrementTick() != pdFALSE )
-                        {
-                            xYieldPending = pdTRUE;
-                        }
-                        else
+                        do
                         {
-                            mtCOVERAGE_TEST_MARKER();
+                            if ( xTaskIncrementTick() != pdFALSE )
+                            {
+                                xYieldPending = pdTRUE;
+                            }
+                            else
+                            {
+                                mtCOVERAGE_TEST_MARKER();
+                            }
+
+                            --uxPendedCounts;
                         }
+                        while ( uxPendedCounts > ( UBaseType_t ) 0U );
 
-                        --uxPendedTicks;
+                        uxPendedTicks = 0;
+                    }
+                    else
+                    {
+                        mtCOVERAGE_TEST_MARKER();
                     }
-                }
-                else
-                {
-                    mtCOVERAGE_TEST_MARKER();
                 }
 
-                if ( xYieldPending == pdTRUE )
+                if ( xYieldPending != pdFALSE )
                 {
 #if( configUSE_PREEMPTION != 0 )
                     {
@@ -1714,6 +2209,7 @@ BaseType_t xTaskResumeAll( void )
         }
     }
     taskEXIT_CRITICAL();
+
     return xAlreadyYielded;
 }
 /*-----------------------------------------------------------*/
@@ -1721,12 +2217,14 @@ BaseType_t xTaskResumeAll( void )
 TickType_t xTaskGetTickCount( void )
 {
     TickType_t xTicks;
+
     /* Critical section required if running on a 16 bit processor. */
     portTICK_TYPE_ENTER_CRITICAL();
     {
         xTicks = xTickCount;
     }
     portTICK_TYPE_EXIT_CRITICAL();
+
     return xTicks;
 }
 /*-----------------------------------------------------------*/
@@ -1735,6 +2233,7 @@ TickType_t xTaskGetTickCountFromISR( void )
 {
     TickType_t xReturn;
     UBaseType_t uxSavedInterruptStatus;
+
     /* RTOS ports that support interrupt nesting have the concept of a maximum
     system call (or maximum API call) interrupt priority.  Interrupts that are
     above the maximum system call priority are kept permanently enabled, even
@@ -1750,11 +2249,13 @@ TickType_t xTaskGetTickCountFromISR( void )
     More information (albeit Cortex-M specific) is provided on the following
     link: http://www.freertos.org/RTOS-Cortex-M3-M4.html */
     portASSERT_IF_INTERRUPT_PRIORITY_INVALID();
+
     uxSavedInterruptStatus = portTICK_TYPE_SET_INTERRUPT_MASK_FROM_ISR();
     {
         xReturn = xTickCount;
     }
     portTICK_TYPE_CLEAR_INTERRUPT_MASK_FROM_ISR( uxSavedInterruptStatus );
+
     return xReturn;
 }
 /*-----------------------------------------------------------*/
@@ -1767,18 +2268,144 @@ UBaseType_t uxTaskGetNumberOfTasks( void )
 }
 /*-----------------------------------------------------------*/
 
-#if ( INCLUDE_pcTaskGetTaskName == 1 )
+char* pcTaskGetName( TaskHandle_t xTaskToQuery ) /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+{
+    TCB_t* pxTCB;
+
+    /* If null is passed in here then the name of the calling task is being
+    queried. */
+    pxTCB = prvGetTCBFromHandle( xTaskToQuery );
+    configASSERT( pxTCB );
+    return &( pxTCB->pcTaskName[ 0 ] );
+}
+/*-----------------------------------------------------------*/
+
+#if ( INCLUDE_xTaskGetHandle == 1 )
+
+static TCB_t* prvSearchForNameWithinSingleList( List_t* pxList, const char pcNameToQuery[] )
+{
+    TCB_t* pxNextTCB, *pxFirstTCB, *pxReturn = NULL;
+    UBaseType_t x;
+    char cNextChar;
+
+    /* This function is called with the scheduler suspended. */
+
+    if ( listCURRENT_LIST_LENGTH( pxList ) > ( UBaseType_t ) 0 )
+    {
+        listGET_OWNER_OF_NEXT_ENTRY( pxFirstTCB, pxList );
+
+        do
+        {
+            listGET_OWNER_OF_NEXT_ENTRY( pxNextTCB, pxList );
+
+            /* Check each character in the name looking for a match or
+            mismatch. */
+            for ( x = ( UBaseType_t ) 0; x < ( UBaseType_t ) configMAX_TASK_NAME_LEN; x++ )
+            {
+                cNextChar = pxNextTCB->pcTaskName[ x ];
+
+                if ( cNextChar != pcNameToQuery[ x ] )
+                {
+                    /* Characters didn't match. */
+                    break;
+                }
+                else if ( cNextChar == 0x00 )
+                {
+                    /* Both strings terminated, a match must have been
+                    found. */
+                    pxReturn = pxNextTCB;
+                    break;
+                }
+                else
+                {
+                    mtCOVERAGE_TEST_MARKER();
+                }
+            }
+
+            if ( pxReturn != NULL )
+            {
+                /* The handle has been found. */
+                break;
+            }
+
+        }
+        while ( pxNextTCB != pxFirstTCB );
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+
+    return pxReturn;
+}
+
+#endif /* INCLUDE_xTaskGetHandle */
+/*-----------------------------------------------------------*/
+
+#if ( INCLUDE_xTaskGetHandle == 1 )
+
+TaskHandle_t xTaskGetHandle( const char* pcNameToQuery ) /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+{
+    UBaseType_t uxQueue = configMAX_PRIORITIES;
+    TCB_t* pxTCB;
+
+    /* Task names will be truncated to configMAX_TASK_NAME_LEN - 1 bytes. */
+    configASSERT( strlen( pcNameToQuery ) < configMAX_TASK_NAME_LEN );
+
+    vTaskSuspendAll();
+    {
+        /* Search the ready lists. */
+        do
+        {
+            uxQueue--;
+            pxTCB = prvSearchForNameWithinSingleList( ( List_t* ) & ( pxReadyTasksLists[ uxQueue ] ), pcNameToQuery );
+
+            if ( pxTCB != NULL )
+            {
+                /* Found the handle. */
+                break;
+            }
+
+        }
+        while ( uxQueue > ( UBaseType_t ) tskIDLE_PRIORITY );  /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
+
+        /* Search the delayed lists. */
+        if ( pxTCB == NULL )
+        {
+            pxTCB = prvSearchForNameWithinSingleList( ( List_t* ) pxDelayedTaskList, pcNameToQuery );
+        }
+
+        if ( pxTCB == NULL )
+        {
+            pxTCB = prvSearchForNameWithinSingleList( ( List_t* ) pxOverflowDelayedTaskList, pcNameToQuery );
+        }
+
+#if ( INCLUDE_vTaskSuspend == 1 )
+        {
+            if ( pxTCB == NULL )
+            {
+                /* Search the suspended list. */
+                pxTCB = prvSearchForNameWithinSingleList( &xSuspendedTaskList, pcNameToQuery );
+            }
+        }
+#endif
+
+#if( INCLUDE_vTaskDelete == 1 )
+        {
+            if ( pxTCB == NULL )
+            {
+                /* Search the deleted list. */
+                pxTCB = prvSearchForNameWithinSingleList( &xTasksWaitingTermination, pcNameToQuery );
+            }
+        }
+#endif
+    }
+    ( void ) xTaskResumeAll();
 
-char* pcTaskGetTaskName( TaskHandle_t xTaskToQuery ) /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
-{
-    TCB_t* pxTCB;
-    /* If null is passed in here then the name of the calling task is being queried. */
-    pxTCB = prvGetTCBFromHandle( xTaskToQuery );
-    configASSERT( pxTCB );
-    return &( pxTCB->pcTaskName[ 0 ] );
+    return ( TaskHandle_t ) pxTCB;
 }
 
-#endif /* INCLUDE_pcTaskGetTaskName */
+#endif /* INCLUDE_xTaskGetHandle */
 /*-----------------------------------------------------------*/
 
 #if ( configUSE_TRACE_FACILITY == 1 )
@@ -1786,6 +2413,7 @@ char* pcTaskGetTaskName( TaskHandle_t xTaskToQuery ) /*lint !e971 Unqualified ch
 UBaseType_t uxTaskGetSystemState( TaskStatus_t* const pxTaskStatusArray, const UBaseType_t uxArraySize, uint32_t* const pulTotalRunTime )
 {
     UBaseType_t uxTask = 0, uxQueue = configMAX_PRIORITIES;
+
     vTaskSuspendAll();
     {
         /* Is there a space in the array for each task in the system? */
@@ -1796,28 +2424,32 @@ UBaseType_t uxTaskGetSystemState( TaskStatus_t* const pxTaskStatusArray, const U
             do
             {
                 uxQueue--;
-                uxTask += prvListTaskWithinSingleList( &( pxTaskStatusArray[ uxTask ] ), &( pxReadyTasksLists[ uxQueue ] ), eReady );
+                uxTask += prvListTasksWithinSingleList( &( pxTaskStatusArray[ uxTask ] ), &( pxReadyTasksLists[ uxQueue ] ), eReady );
+
             }
             while ( uxQueue > ( UBaseType_t ) tskIDLE_PRIORITY );  /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
 
             /* Fill in an TaskStatus_t structure with information on each
             task in the Blocked state. */
-            uxTask += prvListTaskWithinSingleList( &( pxTaskStatusArray[ uxTask ] ), ( List_t* ) pxDelayedTaskList, eBlocked );
-            uxTask += prvListTaskWithinSingleList( &( pxTaskStatusArray[ uxTask ] ), ( List_t* ) pxOverflowDelayedTaskList, eBlocked );
+            uxTask += prvListTasksWithinSingleList( &( pxTaskStatusArray[ uxTask ] ), ( List_t* ) pxDelayedTaskList, eBlocked );
+            uxTask += prvListTasksWithinSingleList( &( pxTaskStatusArray[ uxTask ] ), ( List_t* ) pxOverflowDelayedTaskList, eBlocked );
+
 #if( INCLUDE_vTaskDelete == 1 )
             {
                 /* Fill in an TaskStatus_t structure with information on
                 each task that has been deleted but not yet cleaned up. */
-                uxTask += prvListTaskWithinSingleList( &( pxTaskStatusArray[ uxTask ] ), &xTasksWaitingTermination, eDeleted );
+                uxTask += prvListTasksWithinSingleList( &( pxTaskStatusArray[ uxTask ] ), &xTasksWaitingTermination, eDeleted );
             }
 #endif
+
 #if ( INCLUDE_vTaskSuspend == 1 )
             {
                 /* Fill in an TaskStatus_t structure with information on
                 each task in the Suspended state. */
-                uxTask += prvListTaskWithinSingleList( &( pxTaskStatusArray[ uxTask ] ), &xSuspendedTaskList, eSuspended );
+                uxTask += prvListTasksWithinSingleList( &( pxTaskStatusArray[ uxTask ] ), &xSuspendedTaskList, eSuspended );
             }
 #endif
+
 #if ( configGENERATE_RUN_TIME_STATS == 1)
             {
                 if ( pulTotalRunTime != NULL )
@@ -1844,6 +2476,7 @@ UBaseType_t uxTaskGetSystemState( TaskStatus_t* const pxTaskStatusArray, const U
         }
     }
     ( void ) xTaskResumeAll();
+
     return uxTask;
 }
 
@@ -1882,11 +2515,88 @@ void vTaskStepTick( const TickType_t xTicksToJump )
 #endif /* configUSE_TICKLESS_IDLE */
 /*----------------------------------------------------------*/
 
+#if ( INCLUDE_xTaskAbortDelay == 1 )
+
+BaseType_t xTaskAbortDelay( TaskHandle_t xTask )
+{
+    TCB_t* pxTCB = ( TCB_t* ) xTask;
+    BaseType_t xReturn;
+
+    configASSERT( pxTCB );
+
+    vTaskSuspendAll();
+    {
+        /* A task can only be prematurely removed from the Blocked state if
+        it is actually in the Blocked state. */
+        if ( eTaskGetState( xTask ) == eBlocked )
+        {
+            xReturn = pdPASS;
+
+            /* Remove the reference to the task from the blocked list.  An
+            interrupt won't touch the xStateListItem because the
+            scheduler is suspended. */
+            ( void ) uxListRemove( &( pxTCB->xStateListItem ) );
+
+            /* Is the task waiting on an event also?  If so remove it from
+            the event list too.  Interrupts can touch the event list item,
+            even though the scheduler is suspended, so a critical section
+            is used. */
+            taskENTER_CRITICAL();
+            {
+                if ( listLIST_ITEM_CONTAINER( &( pxTCB->xEventListItem ) ) != NULL )
+                {
+                    ( void ) uxListRemove( &( pxTCB->xEventListItem ) );
+                    pxTCB->ucDelayAborted = pdTRUE;
+                }
+                else
+                {
+                    mtCOVERAGE_TEST_MARKER();
+                }
+            }
+            taskEXIT_CRITICAL();
+
+            /* Place the unblocked task into the appropriate ready list. */
+            prvAddTaskToReadyList( pxTCB );
+
+            /* A task being unblocked cannot cause an immediate context
+            switch if preemption is turned off. */
+#if (  configUSE_PREEMPTION == 1 )
+            {
+                /* Preemption is on, but a context switch should only be
+                performed if the unblocked task has a priority that is
+                equal to or higher than the currently executing task. */
+                if ( pxTCB->uxPriority > pxCurrentTCB->uxPriority )
+                {
+                    /* Pend the yield to be performed when the scheduler
+                    is unsuspended. */
+                    xYieldPending = pdTRUE;
+                }
+                else
+                {
+                    mtCOVERAGE_TEST_MARKER();
+                }
+            }
+#endif /* configUSE_PREEMPTION */
+        }
+        else
+        {
+            xReturn = pdFAIL;
+        }
+    }
+    ( void ) xTaskResumeAll();
+
+    return xReturn;
+}
+
+#endif /* INCLUDE_xTaskAbortDelay */
+/*----------------------------------------------------------*/
+
 BaseType_t xTaskIncrementTick( void )
 {
     TCB_t* pxTCB;
     TickType_t xItemValue;
     BaseType_t xSwitchRequired = pdFALSE;
+
     /* Called by the portable layer each time a tick interrupt occurs.
     Increments the tick then checks to see if the new tick value will cause any
     tasks to be unblocked. */
@@ -1894,104 +2604,105 @@ BaseType_t xTaskIncrementTick( void )
 
     if ( uxSchedulerSuspended == ( UBaseType_t ) pdFALSE )
     {
+        /* Minor optimisation.  The tick count cannot change in this
+        block. */
+        const TickType_t xConstTickCount = xTickCount + ( TickType_t ) 1;
+
         /* Increment the RTOS tick, switching the delayed and overflowed
         delayed lists if it wraps to 0. */
-        ++xTickCount;
-        {
-            /* Minor optimisation.  The tick count cannot change in this
-            block. */
-            const TickType_t xConstTickCount = xTickCount;
+        xTickCount = xConstTickCount;
 
-            if ( xConstTickCount == ( TickType_t ) 0U )
-            {
-                taskSWITCH_DELAYED_LISTS();
-            }
-            else
-            {
-                mtCOVERAGE_TEST_MARKER();
-            }
+        if ( xConstTickCount == ( TickType_t ) 0U ) /*lint !e774 'if' does not always evaluate to false as it is looking for an overflow. */
+        {
+            taskSWITCH_DELAYED_LISTS();
+        }
+        else
+        {
+            mtCOVERAGE_TEST_MARKER();
+        }
 
-            /* See if this tick has made a timeout expire.  Tasks are stored in
-            the	queue in the order of their wake time - meaning once one task
-            has been found whose block time has not expired there is no need to
-            look any further down the list. */
-            if ( xConstTickCount >= xNextTaskUnblockTime )
+        /* See if this tick has made a timeout expire.  Tasks are stored in
+        the	queue in the order of their wake time - meaning once one task
+        has been found whose block time has not expired there is no need to
+        look any further down the list. */
+        if ( xConstTickCount >= xNextTaskUnblockTime )
+        {
+            for ( ;; )
             {
-                for ( ;; )
+                if ( listLIST_IS_EMPTY( pxDelayedTaskList ) != pdFALSE )
+                {
+                    /* The delayed list is empty.  Set xNextTaskUnblockTime
+                    to the maximum possible value so it is extremely
+                    unlikely that the
+                    if( xTickCount >= xNextTaskUnblockTime ) test will pass
+                    next time through. */
+                    xNextTaskUnblockTime = portMAX_DELAY; /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
+                    break;
+                }
+                else
                 {
-                    if ( listLIST_IS_EMPTY( pxDelayedTaskList ) != pdFALSE )
+                    /* The delayed list is not empty, get the value of the
+                    item at the head of the delayed list.  This is the time
+                    at which the task at the head of the delayed list must
+                    be removed from the Blocked state. */
+                    pxTCB = ( TCB_t* ) listGET_OWNER_OF_HEAD_ENTRY( pxDelayedTaskList );
+                    xItemValue = listGET_LIST_ITEM_VALUE( &( pxTCB->xStateListItem ) );
+
+                    if ( xConstTickCount < xItemValue )
                     {
-                        /* The delayed list is empty.  Set xNextTaskUnblockTime
-                        to the maximum possible value so it is extremely
-                        unlikely that the
-                        if( xTickCount >= xNextTaskUnblockTime ) test will pass
-                        next time through. */
-                        xNextTaskUnblockTime = portMAX_DELAY;
+                        /* It is not time to unblock this item yet, but the
+                        item value is the time at which the task at the head
+                        of the blocked list must be removed from the Blocked
+                        state -	so record the item value in
+                        xNextTaskUnblockTime. */
+                        xNextTaskUnblockTime = xItemValue;
                         break;
                     }
                     else
                     {
-                        /* The delayed list is not empty, get the value of the
-                        item at the head of the delayed list.  This is the time
-                        at which the task at the head of the delayed list must
-                        be removed from the Blocked state. */
-                        pxTCB = ( TCB_t* ) listGET_OWNER_OF_HEAD_ENTRY( pxDelayedTaskList );
-                        xItemValue = listGET_LIST_ITEM_VALUE( &( pxTCB->xGenericListItem ) );
-
-                        if ( xConstTickCount < xItemValue )
-                        {
-                            /* It is not time to unblock this item yet, but the
-                            item value is the time at which the task at the head
-                            of the blocked list must be removed from the Blocked
-                            state -	so record the item value in
-                            xNextTaskUnblockTime. */
-                            xNextTaskUnblockTime = xItemValue;
-                            break;
-                        }
-                        else
-                        {
-                            mtCOVERAGE_TEST_MARKER();
-                        }
+                        mtCOVERAGE_TEST_MARKER();
+                    }
 
-                        /* It is time to remove the item from the Blocked state. */
-                        ( void ) uxListRemove( &( pxTCB->xGenericListItem ) );
+                    /* It is time to remove the item from the Blocked state. */
+                    ( void ) uxListRemove( &( pxTCB->xStateListItem ) );
 
-                        /* Is the task waiting on an event also?  If so remove
-                        it from the event list. */
-                        if ( listLIST_ITEM_CONTAINER( &( pxTCB->xEventListItem ) ) != NULL )
+                    /* Is the task waiting on an event also?  If so remove
+                    it from the event list. */
+                    if ( listLIST_ITEM_CONTAINER( &( pxTCB->xEventListItem ) ) != NULL )
+                    {
+                        ( void ) uxListRemove( &( pxTCB->xEventListItem ) );
+                    }
+                    else
+                    {
+                        mtCOVERAGE_TEST_MARKER();
+                    }
+
+                    /* Place the unblocked task into the appropriate ready
+                    list. */
+                    prvAddTaskToReadyList( pxTCB );
+
+                    /* A task being unblocked cannot cause an immediate
+                    context switch if preemption is turned off. */
+#if (  configUSE_PREEMPTION == 1 )
+                    {
+                        /* Preemption is on, but a context switch should
+                        only be performed if the unblocked task has a
+                        priority that is equal to or higher than the
+                        currently executing task. */
+                        if ( pxTCB->uxPriority >= pxCurrentTCB->uxPriority )
                         {
-                            ( void ) uxListRemove( &( pxTCB->xEventListItem ) );
+                            xSwitchRequired = pdTRUE;
                         }
                         else
                         {
                             mtCOVERAGE_TEST_MARKER();
                         }
-
-                        /* Place the unblocked task into the appropriate ready
-                        list. */
-                        prvAddTaskToReadyList( pxTCB );
-                        /* A task being unblocked cannot cause an immediate
-                        context switch if preemption is turned off. */
-#if (  configUSE_PREEMPTION == 1 )
-                        {
-                            /* Preemption is on, but a context switch should
-                            only be performed if the unblocked task has a
-                            priority that is equal to or higher than the
-                            currently executing task. */
-                            if ( pxTCB->uxPriority >= pxCurrentTCB->uxPriority )
-                            {
-                                xSwitchRequired = pdTRUE;
-                            }
-                            else
-                            {
-                                mtCOVERAGE_TEST_MARKER();
-                            }
-                        }
-#endif /* configUSE_PREEMPTION */
                     }
+#endif /* configUSE_PREEMPTION */
                 }
             }
         }
+
         /* Tasks of equal priority to the currently running task will share
         processing time (time slice) if preemption is on, and the application
         writer has not explicitly turned time slicing off. */
@@ -2007,6 +2718,7 @@ BaseType_t xTaskIncrementTick( void )
             }
         }
 #endif /* ( ( configUSE_PREEMPTION == 1 ) && ( configUSE_TIME_SLICING == 1 ) ) */
+
 #if ( configUSE_TICK_HOOK == 1 )
         {
             /* Guard against the tick hook being called when the pended tick
@@ -2025,6 +2737,7 @@ BaseType_t xTaskIncrementTick( void )
     else
     {
         ++uxPendedTicks;
+
         /* The tick hook gets called at regular intervals, even if the
         scheduler is locked. */
 #if ( configUSE_TICK_HOOK == 1 )
@@ -2046,6 +2759,7 @@ BaseType_t xTaskIncrementTick( void )
         }
     }
 #endif /* configUSE_PREEMPTION */
+
     return xSwitchRequired;
 }
 /*-----------------------------------------------------------*/
@@ -2101,6 +2815,7 @@ TaskHookFunction_t xTaskGetApplicationTaskTag( TaskHandle_t xTask )
         xReturn = xTCB->pxTaskTag;
     }
     taskEXIT_CRITICAL();
+
     return xReturn;
 }
 
@@ -2151,6 +2866,7 @@ void vTaskSwitchContext( void )
     {
         xYieldPending = pdFALSE;
         traceTASK_SWITCHED_OUT();
+
 #if ( configGENERATE_RUN_TIME_STATS == 1 )
         {
 #ifdef portALT_GET_RUN_TIME_COUNTER_VALUE
@@ -2160,9 +2876,9 @@ void vTaskSwitchContext( void )
 #endif
 
             /* Add the amount of time the task has been running to the
-            accumulated	time so far.  The time the task started running was
+            accumulated time so far.  The time the task started running was
             stored in ulTaskSwitchedInTime.  Note that there is no overflow
-            protection here	so count values are only valid until the timer
+            protection here so count values are only valid until the timer
             overflows.  The guard against negative values is to protect
             against suspect run time stat counter implementations - which
             are provided by the application, not the kernel. */
@@ -2178,12 +2894,15 @@ void vTaskSwitchContext( void )
             ulTaskSwitchedInTime = ulTotalRunTime;
         }
 #endif /* configGENERATE_RUN_TIME_STATS */
+
         /* Check for stack overflow, if configured. */
         taskCHECK_FOR_STACK_OVERFLOW();
+
         /* Select a new task to run using either the generic C or port
         optimised asm code. */
         taskSELECT_HIGHEST_PRIORITY_TASK();
         traceTASK_SWITCHED_IN();
+
 #if ( configUSE_NEWLIB_REENTRANT == 1 )
         {
             /* Switch Newlib's _impure_ptr variable to point to the _reent
@@ -2197,71 +2916,34 @@ void vTaskSwitchContext( void )
 
 void vTaskPlaceOnEventList( List_t* const pxEventList, const TickType_t xTicksToWait )
 {
-    TickType_t xTimeToWake;
     configASSERT( pxEventList );
+
     /* THIS FUNCTION MUST BE CALLED WITH EITHER INTERRUPTS DISABLED OR THE
     SCHEDULER SUSPENDED AND THE QUEUE BEING ACCESSED LOCKED. */
+
     /* Place the event list item of the TCB in the appropriate event list.
     This is placed in the list in priority order so the highest priority task
     is the first to be woken by the event.  The queue that contains the event
     list is locked, preventing simultaneous access from interrupts. */
     vListInsert( pxEventList, &( pxCurrentTCB->xEventListItem ) );
 
-    /* The task must be removed from from the ready list before it is added to
-    the blocked list as the same list item is used for both lists.  Exclusive
-    access to the ready lists guaranteed because the scheduler is locked. */
-    if ( uxListRemove( &( pxCurrentTCB->xGenericListItem ) ) == ( UBaseType_t ) 0 )
-    {
-        /* The current task must be in a ready list, so there is no need to
-        check, and the port reset macro can be called directly. */
-        portRESET_READY_PRIORITY( pxCurrentTCB->uxPriority, uxTopReadyPriority );
-    }
-    else
-    {
-        mtCOVERAGE_TEST_MARKER();
-    }
-
-#if ( INCLUDE_vTaskSuspend == 1 )
-    {
-        if ( xTicksToWait == portMAX_DELAY )
-        {
-            /* Add the task to the suspended task list instead of a delayed task
-            list to ensure the task is not woken by a timing event.  It will
-            block indefinitely. */
-            vListInsertEnd( &xSuspendedTaskList, &( pxCurrentTCB->xGenericListItem ) );
-        }
-        else
-        {
-            /* Calculate the time at which the task should be woken if the event
-            does not occur.  This may overflow but this doesn't matter, the
-            scheduler will handle it. */
-            xTimeToWake = xTickCount + xTicksToWait;
-            prvAddCurrentTaskToDelayedList( xTimeToWake );
-        }
-    }
-#else /* INCLUDE_vTaskSuspend */
-    {
-        /* Calculate the time at which the task should be woken if the event does
-        not occur.  This may overflow but this doesn't matter, the scheduler
-        will handle it. */
-        xTimeToWake = xTickCount + xTicksToWait;
-        prvAddCurrentTaskToDelayedList( xTimeToWake );
-    }
-#endif /* INCLUDE_vTaskSuspend */
+    prvAddCurrentTaskToDelayedList( xTicksToWait, pdTRUE );
 }
 /*-----------------------------------------------------------*/
 
 void vTaskPlaceOnUnorderedEventList( List_t* pxEventList, const TickType_t xItemValue, const TickType_t xTicksToWait )
 {
-    TickType_t xTimeToWake;
     configASSERT( pxEventList );
+
     /* THIS FUNCTION MUST BE CALLED WITH THE SCHEDULER SUSPENDED.  It is used by
     the event groups implementation. */
     configASSERT( uxSchedulerSuspended != 0 );
+
     /* Store the item value in the event list item.  It is safe to access the
     event list item here as interrupts won't access the event list item of a
     task that is not in the Blocked state. */
     listSET_LIST_ITEM_VALUE( &( pxCurrentTCB->xEventListItem ), xItemValue | taskEVENT_LIST_ITEM_VALUE_IN_USE );
+
     /* Place the event list item of the TCB at the end of the appropriate event
     list.  It is safe to access the event list here because it is part of an
     event group implementation - and interrupts don't access event groups
@@ -2269,118 +2951,38 @@ void vTaskPlaceOnUnorderedEventList( List_t* pxEventList, const TickType_t xItem
     the task level). */
     vListInsertEnd( pxEventList, &( pxCurrentTCB->xEventListItem ) );
 
-    /* The task must be removed from the ready list before it is added to the
-    blocked list.  Exclusive access can be assured to the ready list as the
-    scheduler is locked. */
-    if ( uxListRemove( &( pxCurrentTCB->xGenericListItem ) ) == ( UBaseType_t ) 0 )
-    {
-        /* The current task must be in a ready list, so there is no need to
-        check, and the port reset macro can be called directly. */
-        portRESET_READY_PRIORITY( pxCurrentTCB->uxPriority, uxTopReadyPriority );
-    }
-    else
-    {
-        mtCOVERAGE_TEST_MARKER();
-    }
-
-#if ( INCLUDE_vTaskSuspend == 1 )
-    {
-        if ( xTicksToWait == portMAX_DELAY )
-        {
-            /* Add the task to the suspended task list instead of a delayed task
-            list to ensure it is not woken by a timing event.  It will block
-            indefinitely. */
-            vListInsertEnd( &xSuspendedTaskList, &( pxCurrentTCB->xGenericListItem ) );
-        }
-        else
-        {
-            /* Calculate the time at which the task should be woken if the event
-            does not occur.  This may overflow but this doesn't matter, the
-            kernel will manage it correctly. */
-            xTimeToWake = xTickCount + xTicksToWait;
-            prvAddCurrentTaskToDelayedList( xTimeToWake );
-        }
-    }
-#else /* INCLUDE_vTaskSuspend */
-    {
-        /* Calculate the time at which the task should be woken if the event does
-        not occur.  This may overflow but this doesn't matter, the kernel
-        will manage it correctly. */
-        xTimeToWake = xTickCount + xTicksToWait;
-        prvAddCurrentTaskToDelayedList( xTimeToWake );
-    }
-#endif /* INCLUDE_vTaskSuspend */
+    prvAddCurrentTaskToDelayedList( xTicksToWait, pdTRUE );
 }
 /*-----------------------------------------------------------*/
 
-#if configUSE_TIMERS == 1
+#if( configUSE_TIMERS == 1 )
 
-void vTaskPlaceOnEventListRestricted( List_t* const pxEventList, const TickType_t xTicksToWait, const BaseType_t xWaitIndefinitely )
+void vTaskPlaceOnEventListRestricted( List_t* const pxEventList, TickType_t xTicksToWait, const BaseType_t xWaitIndefinitely )
 {
-    TickType_t xTimeToWake;
     configASSERT( pxEventList );
+
     /* This function should not be called by application code hence the
     'Restricted' in its name.  It is not part of the public API.  It is
     designed for use by kernel code, and has special calling requirements -
     it should be called with the scheduler suspended. */
+
+
     /* Place the event list item of the TCB in the appropriate event list.
     In this case it is assume that this is the only task that is going to
     be waiting on this event list, so the faster vListInsertEnd() function
     can be used in place of vListInsert. */
     vListInsertEnd( pxEventList, &( pxCurrentTCB->xEventListItem ) );
 
-    /* We must remove this task from the ready list before adding it to the
-    blocked list as the same list item is used for both lists.  This
-    function is called with the scheduler locked so interrupts will not
-    access the lists at the same time. */
-    if ( uxListRemove( &( pxCurrentTCB->xGenericListItem ) ) == ( UBaseType_t ) 0 )
-    {
-        /* The current task must be in a ready list, so there is no need to
-        check, and the port reset macro can be called directly. */
-        portRESET_READY_PRIORITY( pxCurrentTCB->uxPriority, uxTopReadyPriority );
-    }
-    else
+    /* If the task should block indefinitely then set the block time to a
+    value that will be recognised as an indefinite delay inside the
+    prvAddCurrentTaskToDelayedList() function. */
+    if ( xWaitIndefinitely != pdFALSE )
     {
-        mtCOVERAGE_TEST_MARKER();
+        xTicksToWait = portMAX_DELAY;
     }
 
-    /* If vTaskSuspend() is available then the suspended task list is also
-    available and a task that is blocking indefinitely can enter the
-    suspended state (it is not really suspended as it will re-enter the
-    Ready state when the event it is waiting indefinitely for occurs).
-    Blocking indefinitely is useful when using tickless idle mode as when
-    all tasks are blocked indefinitely all timers can be turned off. */
-#if( INCLUDE_vTaskSuspend == 1 )
-    {
-        if ( xWaitIndefinitely == pdTRUE )
-        {
-            /* Add the task to the suspended task list instead of a delayed
-            task list to ensure the task is not woken by a timing event.  It
-            will block indefinitely. */
-            vListInsertEnd( &xSuspendedTaskList, &( pxCurrentTCB->xGenericListItem ) );
-        }
-        else
-        {
-            /* Calculate the time at which the task should be woken if the
-            event does not occur.  This may overflow but this doesn't
-            matter. */
-            xTimeToWake = xTickCount + xTicksToWait;
-            traceTASK_DELAY_UNTIL();
-            prvAddCurrentTaskToDelayedList( xTimeToWake );
-        }
-    }
-#else
-    {
-        /* Calculate the time at which the task should be woken if the event
-        does not occur.  This may overflow but this doesn't matter. */
-        xTimeToWake = xTickCount + xTicksToWait;
-        traceTASK_DELAY_UNTIL();
-        prvAddCurrentTaskToDelayedList( xTimeToWake );
-        /* Remove compiler warnings when INCLUDE_vTaskSuspend() is not
-        defined. */
-        ( void ) xWaitIndefinitely;
-    }
-#endif
+    traceTASK_DELAY_UNTIL( ( xTickCount + xTicksToWait ) );
+    prvAddCurrentTaskToDelayedList( xTicksToWait, xWaitIndefinitely );
 }
 
 #endif /* configUSE_TIMERS */
@@ -2390,8 +2992,10 @@ BaseType_t xTaskRemoveFromEventList( const List_t* const pxEventList )
 {
     TCB_t* pxUnblockedTCB;
     BaseType_t xReturn;
+
     /* THIS FUNCTION MUST BE CALLED FROM A CRITICAL SECTION.  It can also be
     called from a critical section within an ISR. */
+
     /* The event list is sorted in priority order, so the first in the list can
     be removed as it is known to be the highest priority.  Remove the TCB from
     the delayed list, and add it to the ready list.
@@ -2408,7 +3012,7 @@ BaseType_t xTaskRemoveFromEventList( const List_t* const pxEventList )
 
     if ( uxSchedulerSuspended == ( UBaseType_t ) pdFALSE )
     {
-        ( void ) uxListRemove( &( pxUnblockedTCB->xGenericListItem ) );
+        ( void ) uxListRemove( &( pxUnblockedTCB->xStateListItem ) );
         prvAddTaskToReadyList( pxUnblockedTCB );
     }
     else
@@ -2424,6 +3028,7 @@ BaseType_t xTaskRemoveFromEventList( const List_t* const pxEventList )
         priority than the calling task.  This allows the calling task to know if
         it should force a context switch now. */
         xReturn = pdTRUE;
+
         /* Mark that a yield is pending in case the user is not using the
         "xHigherPriorityTaskWoken" parameter to an ISR safe FreeRTOS function. */
         xYieldPending = pdTRUE;
@@ -2446,53 +3051,60 @@ BaseType_t xTaskRemoveFromEventList( const List_t* const pxEventList )
         prvResetNextTaskUnblockTime();
     }
 #endif
+
     return xReturn;
 }
 /*-----------------------------------------------------------*/
 
-BaseType_t xTaskRemoveFromUnorderedEventList( ListItem_t* pxEventListItem, const TickType_t xItemValue )
+void vTaskRemoveFromUnorderedEventList( ListItem_t* pxEventListItem, const TickType_t xItemValue )
 {
     TCB_t* pxUnblockedTCB;
-    BaseType_t xReturn;
+
     /* THIS FUNCTION MUST BE CALLED WITH THE SCHEDULER SUSPENDED.  It is used by
     the event flags implementation. */
     configASSERT( uxSchedulerSuspended != pdFALSE );
+
     /* Store the new item value in the event list. */
     listSET_LIST_ITEM_VALUE( pxEventListItem, xItemValue | taskEVENT_LIST_ITEM_VALUE_IN_USE );
+
     /* Remove the event list form the event flag.  Interrupts do not access
     event flags. */
     pxUnblockedTCB = ( TCB_t* ) listGET_LIST_ITEM_OWNER( pxEventListItem );
     configASSERT( pxUnblockedTCB );
     ( void ) uxListRemove( pxEventListItem );
+
     /* Remove the task from the delayed list and add it to the ready list.  The
     scheduler is suspended so interrupts will not be accessing the ready
     lists. */
-    ( void ) uxListRemove( &( pxUnblockedTCB->xGenericListItem ) );
+    ( void ) uxListRemove( &( pxUnblockedTCB->xStateListItem ) );
     prvAddTaskToReadyList( pxUnblockedTCB );
 
     if ( pxUnblockedTCB->uxPriority > pxCurrentTCB->uxPriority )
     {
-        /* Return true if the task removed from the event list has
-        a higher priority than the calling task.  This allows
-        the calling task to know if it should force a context
-        switch now. */
-        xReturn = pdTRUE;
-        /* Mark that a yield is pending in case the user is not using the
-        "xHigherPriorityTaskWoken" parameter to an ISR safe FreeRTOS function. */
+        /* The unblocked task has a priority above that of the calling task, so
+        a context switch is required.  This function is called with the
+        scheduler suspended so xYieldPending is set so the context switch
+        occurs immediately that the scheduler is resumed (unsuspended). */
         xYieldPending = pdTRUE;
     }
-    else
-    {
-        xReturn = pdFALSE;
-    }
-
-    return xReturn;
 }
 /*-----------------------------------------------------------*/
 
 void vTaskSetTimeOutState( TimeOut_t* const pxTimeOut )
 {
     configASSERT( pxTimeOut );
+    taskENTER_CRITICAL();
+    {
+        pxTimeOut->xOverflowCount = xNumOfOverflows;
+        pxTimeOut->xTimeOnEntering = xTickCount;
+    }
+    taskEXIT_CRITICAL();
+}
+/*-----------------------------------------------------------*/
+
+void vTaskInternalSetTimeOutState( TimeOut_t* const pxTimeOut )
+{
+    /* For internal use only as it does not use a critical section. */
     pxTimeOut->xOverflowCount = xNumOfOverflows;
     pxTimeOut->xTimeOnEntering = xTickCount;
 }
@@ -2501,44 +3113,63 @@ void vTaskSetTimeOutState( TimeOut_t* const pxTimeOut )
 BaseType_t xTaskCheckForTimeOut( TimeOut_t* const pxTimeOut, TickType_t* const pxTicksToWait )
 {
     BaseType_t xReturn;
+
     configASSERT( pxTimeOut );
     configASSERT( pxTicksToWait );
+
     taskENTER_CRITICAL();
     {
         /* Minor optimisation.  The tick count cannot change in this block. */
         const TickType_t xConstTickCount = xTickCount;
-#if ( INCLUDE_vTaskSuspend == 1 )
+        const TickType_t xElapsedTime = xConstTickCount - pxTimeOut->xTimeOnEntering;
+
+#if( INCLUDE_xTaskAbortDelay == 1 )
 
-        /* If INCLUDE_vTaskSuspend is set to 1 and the block time specified is
-        the maximum block time then the task should block indefinitely, and
-        therefore never time out. */
-        if ( *pxTicksToWait == portMAX_DELAY )
+        if ( pxCurrentTCB->ucDelayAborted != pdFALSE )
         {
-            xReturn = pdFALSE;
+            /* The delay was aborted, which is not the same as a time out,
+            but has the same result. */
+            pxCurrentTCB->ucDelayAborted = pdFALSE;
+            xReturn = pdTRUE;
         }
-        else /* We are not blocking indefinitely, perform the checks below. */
+        else
 #endif
-            if ( ( xNumOfOverflows != pxTimeOut->xOverflowCount ) && ( xConstTickCount >= pxTimeOut->xTimeOnEntering ) ) /*lint !e525 Indentation preferred as is to make code within pre-processor directives clearer. */
-            {
-                /* The tick count is greater than the time at which vTaskSetTimeout()
-                was called, but has also overflowed since vTaskSetTimeOut() was called.
-                It must have wrapped all the way around and gone past us again. This
-                passed since vTaskSetTimeout() was called. */
-                xReturn = pdTRUE;
-            }
-            else if ( ( xConstTickCount - pxTimeOut->xTimeOnEntering ) < *pxTicksToWait )
+
+#if ( INCLUDE_vTaskSuspend == 1 )
+            if ( *pxTicksToWait == portMAX_DELAY )
             {
-                /* Not a genuine timeout. Adjust parameters for time remaining. */
-                *pxTicksToWait -= ( xConstTickCount -  pxTimeOut->xTimeOnEntering );
-                vTaskSetTimeOutState( pxTimeOut );
+                /* If INCLUDE_vTaskSuspend is set to 1 and the block time
+                specified is the maximum block time then the task should block
+                indefinitely, and therefore never time out. */
                 xReturn = pdFALSE;
             }
-            else
-            {
-                xReturn = pdTRUE;
-            }
+            else
+#endif
+
+                if ( ( xNumOfOverflows != pxTimeOut->xOverflowCount ) && ( xConstTickCount >= pxTimeOut->xTimeOnEntering ) ) /*lint !e525 Indentation preferred as is to make code within pre-processor directives clearer. */
+                {
+                    /* The tick count is greater than the time at which
+                    vTaskSetTimeout() was called, but has also overflowed since
+                    vTaskSetTimeOut() was called.  It must have wrapped all the way
+                    around and gone past again. This passed since vTaskSetTimeout()
+                    was called. */
+                    xReturn = pdTRUE;
+                }
+                else if ( xElapsedTime < *pxTicksToWait ) /*lint !e961 Explicit casting is only redundant with some compilers, whereas others require it to prevent integer conversion errors. */
+                {
+                    /* Not a genuine timeout. Adjust parameters for time remaining. */
+                    *pxTicksToWait -= xElapsedTime;
+                    vTaskInternalSetTimeOutState( pxTimeOut );
+                    xReturn = pdFALSE;
+                }
+                else
+                {
+                    *pxTicksToWait = 0;
+                    xReturn = pdTRUE;
+                }
     }
     taskEXIT_CRITICAL();
+
     return xReturn;
 }
 /*-----------------------------------------------------------*/
@@ -2603,10 +3234,20 @@ static portTASK_FUNCTION( prvIdleTask, pvParameters )
     /* Stop warnings. */
     ( void ) pvParameters;
 
+    /** THIS IS THE RTOS IDLE TASK - WHICH IS CREATED AUTOMATICALLY WHEN THE
+    SCHEDULER IS STARTED. **/
+
+    /* In case a task that has a secure context deletes itself, in which case
+    the idle task is responsible for deleting the task's secure context, if
+    any. */
+    portTASK_CALLS_SECURE_FUNCTIONS();
+
     for ( ;; )
     {
-        /* See if any tasks have been deleted. */
+        /* See if any tasks have deleted themselves - if so then the idle task
+        is responsible for freeing the deleted task's TCB and stack. */
         prvCheckTasksWaitingTermination();
+
 #if ( configUSE_PREEMPTION == 0 )
         {
             /* If we are not using preemption we keep forcing a task switch to
@@ -2616,6 +3257,7 @@ static portTASK_FUNCTION( prvIdleTask, pvParameters )
             taskYIELD();
         }
 #endif /* configUSE_PREEMPTION */
+
 #if ( ( configUSE_PREEMPTION == 1 ) && ( configIDLE_SHOULD_YIELD == 1 ) )
         {
             /* When using preemption tasks of equal priority will be
@@ -2637,9 +3279,11 @@ static portTASK_FUNCTION( prvIdleTask, pvParameters )
             }
         }
 #endif /* ( ( configUSE_PREEMPTION == 1 ) && ( configIDLE_SHOULD_YIELD == 1 ) ) */
+
 #if ( configUSE_IDLE_HOOK == 1 )
         {
             extern void vApplicationIdleHook( void );
+
             /* Call the user defined function from within the idle task.  This
             allows the application designer to add background functionality
             without the overhead of a separate task.
@@ -2648,6 +3292,7 @@ static portTASK_FUNCTION( prvIdleTask, pvParameters )
             vApplicationIdleHook();
         }
 #endif /* configUSE_IDLE_HOOK */
+
         /* This conditional compilation should use inequality to 0, not equality
         to 1.  This is to ensure portSUPPRESS_TICKS_AND_SLEEP() is called when
         user defined low power mode	implementations require
@@ -2655,6 +3300,7 @@ static portTASK_FUNCTION( prvIdleTask, pvParameters )
 #if ( configUSE_TICKLESS_IDLE != 0 )
         {
             TickType_t xExpectedIdleTime;
+
             /* It is not desirable to suspend then resume the scheduler on
             each iteration of the idle task.  Therefore, a preliminary
             test of the expected idle time is performed without the
@@ -2672,6 +3318,11 @@ static portTASK_FUNCTION( prvIdleTask, pvParameters )
                     configASSERT( xNextTaskUnblockTime >= xTickCount );
                     xExpectedIdleTime = prvGetExpectedIdleTime();
 
+                    /* Define the following macro to set xExpectedIdleTime to 0
+                    if the application does not want
+                    portSUPPRESS_TICKS_AND_SLEEP() to be called. */
+                    configPRE_SUPPRESS_TICKS_AND_SLEEP_PROCESSING( xExpectedIdleTime );
+
                     if ( xExpectedIdleTime >= configEXPECTED_IDLE_TIME_BEFORE_SLEEP )
                     {
                         traceLOW_POWER_IDLE_BEGIN();
@@ -2735,106 +3386,6 @@ eSleepModeStatus eTaskConfirmSleepModeStatus( void )
 #endif /* configUSE_TICKLESS_IDLE */
 /*-----------------------------------------------------------*/
 
-static void prvInitialiseTCBVariables( TCB_t* const pxTCB, const char* const pcName, UBaseType_t uxPriority, const MemoryRegion_t* const xRegions, const uint16_t usStackDepth )    /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
-{
-    UBaseType_t x;
-
-    /* Store the task name in the TCB. */
-    for ( x = ( UBaseType_t ) 0; x < ( UBaseType_t ) configMAX_TASK_NAME_LEN; x++ )
-    {
-        pxTCB->pcTaskName[ x ] = pcName[ x ];
-
-        /* Don't copy all configMAX_TASK_NAME_LEN if the string is shorter than
-        configMAX_TASK_NAME_LEN characters just in case the memory after the
-        string is not accessible (extremely unlikely). */
-        if ( pcName[ x ] == 0x00 )
-        {
-            break;
-        }
-        else
-        {
-            mtCOVERAGE_TEST_MARKER();
-        }
-    }
-
-    /* Ensure the name string is terminated in the case that the string length
-    was greater or equal to configMAX_TASK_NAME_LEN. */
-    pxTCB->pcTaskName[ configMAX_TASK_NAME_LEN - 1 ] = '\0';
-
-    /* This is used as an array index so must ensure it's not too large.  First
-    remove the privilege bit if one is present. */
-    if ( uxPriority >= ( UBaseType_t ) configMAX_PRIORITIES )
-    {
-        uxPriority = ( UBaseType_t ) configMAX_PRIORITIES - ( UBaseType_t ) 1U;
-    }
-    else
-    {
-        mtCOVERAGE_TEST_MARKER();
-    }
-
-    pxTCB->uxPriority = uxPriority;
-#if ( configUSE_MUTEXES == 1 )
-    {
-        pxTCB->uxBasePriority = uxPriority;
-        pxTCB->uxMutexesHeld = 0;
-    }
-#endif /* configUSE_MUTEXES */
-    vListInitialiseItem( &( pxTCB->xGenericListItem ) );
-    vListInitialiseItem( &( pxTCB->xEventListItem ) );
-    /* Set the pxTCB as a link back from the ListItem_t.  This is so we can get
-    back to	the containing TCB from a generic item in a list. */
-    listSET_LIST_ITEM_OWNER( &( pxTCB->xGenericListItem ), pxTCB );
-    /* Event lists are always in priority order. */
-    listSET_LIST_ITEM_VALUE( &( pxTCB->xEventListItem ), ( TickType_t ) configMAX_PRIORITIES - ( TickType_t ) uxPriority ); /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
-    listSET_LIST_ITEM_OWNER( &( pxTCB->xEventListItem ), pxTCB );
-#if ( portCRITICAL_NESTING_IN_TCB == 1 )
-    {
-        pxTCB->uxCriticalNesting = ( UBaseType_t ) 0U;
-    }
-#endif /* portCRITICAL_NESTING_IN_TCB */
-#if ( configUSE_APPLICATION_TASK_TAG == 1 )
-    {
-        pxTCB->pxTaskTag = NULL;
-    }
-#endif /* configUSE_APPLICATION_TASK_TAG */
-#if ( configGENERATE_RUN_TIME_STATS == 1 )
-    {
-        pxTCB->ulRunTimeCounter = 0UL;
-    }
-#endif /* configGENERATE_RUN_TIME_STATS */
-#if ( portUSING_MPU_WRAPPERS == 1 )
-    {
-        vPortStoreTaskMPUSettings( &( pxTCB->xMPUSettings ), xRegions, pxTCB->pxStack, usStackDepth );
-    }
-#else /* portUSING_MPU_WRAPPERS */
-    {
-        ( void ) xRegions;
-        ( void ) usStackDepth;
-    }
-#endif /* portUSING_MPU_WRAPPERS */
-#if( configNUM_THREAD_LOCAL_STORAGE_POINTERS != 0 )
-    {
-        for ( x = 0; x < ( UBaseType_t ) configNUM_THREAD_LOCAL_STORAGE_POINTERS; x++ )
-        {
-            pxTCB->pvThreadLocalStoragePointers[ x ] = NULL;
-        }
-    }
-#endif
-#if ( configUSE_TASK_NOTIFICATIONS == 1 )
-    {
-        pxTCB->ulNotifiedValue = 0;
-        pxTCB->eNotifyState = eNotWaitingNotification;
-    }
-#endif
-#if ( configUSE_NEWLIB_REENTRANT == 1 )
-    {
-        /* Initialise this task's Newlib reent structure. */
-        _REENT_INIT_PTR( ( &( pxTCB->xNewLib_reent ) ) );
-    }
-#endif /* configUSE_NEWLIB_REENTRANT */
-}
-/*-----------------------------------------------------------*/
-
 #if ( configNUM_THREAD_LOCAL_STORAGE_POINTERS != 0 )
 
 void vTaskSetThreadLocalStoragePointer( TaskHandle_t xTaskToSet, BaseType_t xIndex, void* pvValue )
@@ -2879,9 +3430,11 @@ void* pvTaskGetThreadLocalStoragePointer( TaskHandle_t xTaskToQuery, BaseType_t
 void vTaskAllocateMPURegions( TaskHandle_t xTaskToModify, const MemoryRegion_t* const xRegions )
 {
     TCB_t* pxTCB;
+
     /* If null is passed in here then we are modifying the MPU settings of
     the calling task. */
     pxTCB = prvGetTCBFromHandle( xTaskToModify );
+
     vPortStoreTaskMPUSettings( &( pxTCB->xMPUSettings ), xRegions, NULL, 0 );
 }
 
@@ -2900,16 +3453,19 @@ static void prvInitialiseTaskLists( void )
     vListInitialise( &xDelayedTaskList1 );
     vListInitialise( &xDelayedTaskList2 );
     vListInitialise( &xPendingReadyList );
+
 #if ( INCLUDE_vTaskDelete == 1 )
     {
         vListInitialise( &xTasksWaitingTermination );
     }
 #endif /* INCLUDE_vTaskDelete */
+
 #if ( INCLUDE_vTaskSuspend == 1 )
     {
         vListInitialise( &xSuspendedTaskList );
     }
 #endif /* INCLUDE_vTaskSuspend */
+
     /* Start with pxDelayedTaskList using list1 and the pxOverflowDelayedTaskList
     using list2. */
     pxDelayedTaskList = &xDelayedTaskList1;
@@ -2919,151 +3475,134 @@ static void prvInitialiseTaskLists( void )
 
 static void prvCheckTasksWaitingTermination( void )
 {
+
+    /** THIS FUNCTION IS CALLED FROM THE RTOS IDLE TASK **/
+
 #if ( INCLUDE_vTaskDelete == 1 )
     {
-        BaseType_t xListIsEmpty;
+        TCB_t* pxTCB;
 
-        /* ucTasksDeleted is used to prevent vTaskSuspendAll() being called
-        too often in the idle task. */
-        while ( uxTasksDeleted > ( UBaseType_t ) 0U )
+        /* uxDeletedTasksWaitingCleanUp is used to prevent vTaskSuspendAll()
+        being called too often in the idle task. */
+        while ( uxDeletedTasksWaitingCleanUp > ( UBaseType_t ) 0U )
         {
-            vTaskSuspendAll();
+            taskENTER_CRITICAL();
             {
-                xListIsEmpty = listLIST_IS_EMPTY( &xTasksWaitingTermination );
+                pxTCB = ( TCB_t* ) listGET_OWNER_OF_HEAD_ENTRY( ( &xTasksWaitingTermination ) );
+                ( void ) uxListRemove( &( pxTCB->xStateListItem ) );
+                --uxCurrentNumberOfTasks;
+                --uxDeletedTasksWaitingCleanUp;
             }
-            ( void ) xTaskResumeAll();
+            taskEXIT_CRITICAL();
 
-            if ( xListIsEmpty == pdFALSE )
-            {
-                TCB_t* pxTCB;
-                taskENTER_CRITICAL();
-                {
-                    pxTCB = ( TCB_t* ) listGET_OWNER_OF_HEAD_ENTRY( ( &xTasksWaitingTermination ) );
-                    ( void ) uxListRemove( &( pxTCB->xGenericListItem ) );
-                    --uxCurrentNumberOfTasks;
-                    --uxTasksDeleted;
-                }
-                taskEXIT_CRITICAL();
-                prvDeleteTCB( pxTCB );
-            }
-            else
-            {
-                mtCOVERAGE_TEST_MARKER();
-            }
+            prvDeleteTCB( pxTCB );
         }
     }
-#endif /* vTaskDelete */
+#endif /* INCLUDE_vTaskDelete */
 }
 /*-----------------------------------------------------------*/
 
-static void prvAddCurrentTaskToDelayedList( const TickType_t xTimeToWake )
+#if( configUSE_TRACE_FACILITY == 1 )
+
+void vTaskGetInfo( TaskHandle_t xTask, TaskStatus_t* pxTaskStatus, BaseType_t xGetFreeStackSpace, eTaskState eState )
 {
-    /* The list item will be inserted in wake time order. */
-    listSET_LIST_ITEM_VALUE( &( pxCurrentTCB->xGenericListItem ), xTimeToWake );
+    TCB_t* pxTCB;
+
+    /* xTask is NULL then get the state of the calling task. */
+    pxTCB = prvGetTCBFromHandle( xTask );
+
+    pxTaskStatus->xHandle = ( TaskHandle_t ) pxTCB;
+    pxTaskStatus->pcTaskName = ( const char* ) & ( pxTCB->pcTaskName [ 0 ] );
+    pxTaskStatus->uxCurrentPriority = pxTCB->uxPriority;
+    pxTaskStatus->pxStackBase = pxTCB->pxStack;
+    pxTaskStatus->xTaskNumber = pxTCB->uxTCBNumber;
 
-    if ( xTimeToWake < xTickCount )
+#if ( configUSE_MUTEXES == 1 )
     {
-        /* Wake time has overflowed.  Place this item in the overflow list. */
-        vListInsert( pxOverflowDelayedTaskList, &( pxCurrentTCB->xGenericListItem ) );
+        pxTaskStatus->uxBasePriority = pxTCB->uxBasePriority;
     }
-    else
+#else
     {
-        /* The wake time has not overflowed, so the current block list is used. */
-        vListInsert( pxDelayedTaskList, &( pxCurrentTCB->xGenericListItem ) );
-
-        /* If the task entering the blocked state was placed at the head of the
-        list of blocked tasks then xNextTaskUnblockTime needs to be updated
-        too. */
-        if ( xTimeToWake < xNextTaskUnblockTime )
-        {
-            xNextTaskUnblockTime = xTimeToWake;
-        }
-        else
-        {
-            mtCOVERAGE_TEST_MARKER();
-        }
+        pxTaskStatus->uxBasePriority = 0;
     }
-}
-/*-----------------------------------------------------------*/
+#endif
 
-static TCB_t* prvAllocateTCBAndStack( const uint16_t usStackDepth, StackType_t* const puxStackBuffer )
-{
-    TCB_t* pxNewTCB;
-    /* If the stack grows down then allocate the stack then the TCB so the stack
-    does not grow into the TCB.  Likewise if the stack grows up then allocate
-    the TCB then the stack. */
-#if( portSTACK_GROWTH > 0 )
+#if ( configGENERATE_RUN_TIME_STATS == 1 )
     {
-        /* Allocate space for the TCB.  Where the memory comes from depends on
-        the implementation of the port malloc function. */
-        pxNewTCB = ( TCB_t* ) pvPortMalloc( sizeof( TCB_t ) );
+        pxTaskStatus->ulRunTimeCounter = pxTCB->ulRunTimeCounter;
+    }
+#else
+    {
+        pxTaskStatus->ulRunTimeCounter = 0;
+    }
+#endif
 
-        if ( pxNewTCB != NULL )
+    /* Obtaining the task state is a little fiddly, so is only done if the
+    value of eState passed into this function is eInvalid - otherwise the
+    state is just set to whatever is passed in. */
+    if ( eState != eInvalid )
+    {
+        if ( pxTCB == pxCurrentTCB )
         {
-            /* Allocate space for the stack used by the task being created.
-            The base of the stack memory stored in the TCB so the task can
-            be deleted later if required. */
-            pxNewTCB->pxStack = ( StackType_t* ) pvPortMallocAligned( ( ( ( size_t ) usStackDepth ) * sizeof( StackType_t ) ), puxStackBuffer );  /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
+            pxTaskStatus->eCurrentState = eRunning;
+        }
+        else
+        {
+            pxTaskStatus->eCurrentState = eState;
 
-            if ( pxNewTCB->pxStack == NULL )
+#if ( INCLUDE_vTaskSuspend == 1 )
             {
-                /* Could not allocate the stack.  Delete the allocated TCB. */
-                vPortFree( pxNewTCB );
-                pxNewTCB = NULL;
+                /* If the task is in the suspended list then there is a
+                chance it is actually just blocked indefinitely - so really
+                it should be reported as being in the Blocked state. */
+                if ( eState == eSuspended )
+                {
+                    vTaskSuspendAll();
+                    {
+                        if ( listLIST_ITEM_CONTAINER( &( pxTCB->xEventListItem ) ) != NULL )
+                        {
+                            pxTaskStatus->eCurrentState = eBlocked;
+                        }
+                    }
+                    ( void ) xTaskResumeAll();
+                }
             }
+#endif /* INCLUDE_vTaskSuspend */
         }
     }
-#else /* portSTACK_GROWTH */
+    else
     {
-        StackType_t* pxStack;
-        /* Allocate space for the stack used by the task being created. */
-        pxStack = ( StackType_t* ) pvPortMallocAligned( ( ( ( size_t ) usStackDepth ) * sizeof( StackType_t ) ), puxStackBuffer );  /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
+        pxTaskStatus->eCurrentState = eTaskGetState( pxTCB );
+    }
 
-        if ( pxStack != NULL )
+    /* Obtaining the stack space takes some time, so the xGetFreeStackSpace
+    parameter is provided to allow it to be skipped. */
+    if ( xGetFreeStackSpace != pdFALSE )
+    {
+#if ( portSTACK_GROWTH > 0 )
         {
-            /* Allocate space for the TCB.  Where the memory comes from depends
-            on the implementation of the port malloc function. */
-            pxNewTCB = ( TCB_t* ) pvPortMalloc( sizeof( TCB_t ) );
-
-            if ( pxNewTCB != NULL )
-            {
-                /* Store the stack location in the TCB. */
-                pxNewTCB->pxStack = pxStack;
-            }
-            else
-            {
-                /* The stack cannot be used as the TCB was not created.  Free it
-                again. */
-                vPortFree( pxStack );
-            }
+            pxTaskStatus->usStackHighWaterMark = prvTaskCheckFreeStackSpace( ( uint8_t* ) pxTCB->pxEndOfStack );
         }
-        else
+#else
         {
-            pxNewTCB = NULL;
+            pxTaskStatus->usStackHighWaterMark = prvTaskCheckFreeStackSpace( ( uint8_t* ) pxTCB->pxStack );
         }
+#endif
     }
-#endif /* portSTACK_GROWTH */
-
-    if ( pxNewTCB != NULL )
+    else
     {
-        /* Avoid dependency on memset() if it is not required. */
-#if( ( configCHECK_FOR_STACK_OVERFLOW > 1 ) || ( configUSE_TRACE_FACILITY == 1 ) || ( INCLUDE_uxTaskGetStackHighWaterMark == 1 ) )
-        {
-            /* Just to help debugging. */
-            ( void ) memset( pxNewTCB->pxStack, ( int ) tskSTACK_FILL_BYTE, ( size_t ) usStackDepth * sizeof( StackType_t ) );
-        }
-#endif /* ( ( configCHECK_FOR_STACK_OVERFLOW > 1 ) || ( ( configUSE_TRACE_FACILITY == 1 ) || ( INCLUDE_uxTaskGetStackHighWaterMark == 1 ) ) ) */
+        pxTaskStatus->usStackHighWaterMark = 0;
     }
-
-    return pxNewTCB;
 }
+
+#endif /* configUSE_TRACE_FACILITY */
 /*-----------------------------------------------------------*/
 
 #if ( configUSE_TRACE_FACILITY == 1 )
 
-static UBaseType_t prvListTaskWithinSingleList( TaskStatus_t* pxTaskStatusArray, List_t* pxList, eTaskState eState )
+static UBaseType_t prvListTasksWithinSingleList( TaskStatus_t* pxTaskStatusArray, List_t* pxList, eTaskState eState )
 {
-    volatile TCB_t* pxNextTCB, *pxFirstTCB;
+    configLIST_VOLATILE TCB_t* pxNextTCB, *pxFirstTCB;
     UBaseType_t uxTask = 0;
 
     if ( listCURRENT_LIST_LENGTH( pxList ) > ( UBaseType_t ) 0 )
@@ -3077,52 +3616,7 @@ static UBaseType_t prvListTaskWithinSingleList( TaskStatus_t* pxTaskStatusArray,
         do
         {
             listGET_OWNER_OF_NEXT_ENTRY( pxNextTCB, pxList );
-            pxTaskStatusArray[ uxTask ].xHandle = ( TaskHandle_t ) pxNextTCB;
-            pxTaskStatusArray[ uxTask ].pcTaskName = ( const char* ) & ( pxNextTCB->pcTaskName [ 0 ] );
-            pxTaskStatusArray[ uxTask ].xTaskNumber = pxNextTCB->uxTCBNumber;
-            pxTaskStatusArray[ uxTask ].eCurrentState = eState;
-            pxTaskStatusArray[ uxTask ].uxCurrentPriority = pxNextTCB->uxPriority;
-#if ( INCLUDE_vTaskSuspend == 1 )
-            {
-                /* If the task is in the suspended list then there is a chance
-                it is actually just blocked indefinitely - so really it should
-                be reported as being in the Blocked state. */
-                if ( eState == eSuspended )
-                {
-                    if ( listLIST_ITEM_CONTAINER( &( pxNextTCB->xEventListItem ) ) != NULL )
-                    {
-                        pxTaskStatusArray[ uxTask ].eCurrentState = eBlocked;
-                    }
-                }
-            }
-#endif /* INCLUDE_vTaskSuspend */
-#if ( configUSE_MUTEXES == 1 )
-            {
-                pxTaskStatusArray[ uxTask ].uxBasePriority = pxNextTCB->uxBasePriority;
-            }
-#else
-            {
-                pxTaskStatusArray[ uxTask ].uxBasePriority = 0;
-            }
-#endif
-#if ( configGENERATE_RUN_TIME_STATS == 1 )
-            {
-                pxTaskStatusArray[ uxTask ].ulRunTimeCounter = pxNextTCB->ulRunTimeCounter;
-            }
-#else
-            {
-                pxTaskStatusArray[ uxTask ].ulRunTimeCounter = 0;
-            }
-#endif
-#if ( portSTACK_GROWTH > 0 )
-            {
-                pxTaskStatusArray[ uxTask ].usStackHighWaterMark = prvTaskCheckFreeStackSpace( ( uint8_t* ) pxNextTCB->pxEndOfStack );
-            }
-#else
-            {
-                pxTaskStatusArray[ uxTask ].usStackHighWaterMark = prvTaskCheckFreeStackSpace( ( uint8_t* ) pxNextTCB->pxStack );
-            }
-#endif
+            vTaskGetInfo( ( TaskHandle_t ) pxNextTCB, &( pxTaskStatusArray[ uxTask ] ), pdTRUE, eState );
             uxTask++;
         }
         while ( pxNextTCB != pxFirstTCB );
@@ -3151,6 +3645,7 @@ static uint16_t prvTaskCheckFreeStackSpace( const uint8_t* pucStackByte )
     }
 
     ulCount /= ( uint32_t ) sizeof( StackType_t ); /*lint !e961 Casting is not redundant on smaller architectures. */
+
     return ( uint16_t ) ulCount;
 }
 
@@ -3164,7 +3659,9 @@ UBaseType_t uxTaskGetStackHighWaterMark( TaskHandle_t xTask )
     TCB_t* pxTCB;
     uint8_t* pucEndOfStack;
     UBaseType_t uxReturn;
+
     pxTCB = prvGetTCBFromHandle( xTask );
+
 #if portSTACK_GROWTH < 0
     {
         pucEndOfStack = ( uint8_t* ) pxTCB->pxStack;
@@ -3174,7 +3671,9 @@ UBaseType_t uxTaskGetStackHighWaterMark( TaskHandle_t xTask )
         pucEndOfStack = ( uint8_t* ) pxTCB->pxEndOfStack;
     }
 #endif
+
     uxReturn = ( UBaseType_t ) prvTaskCheckFreeStackSpace( pucEndOfStack );
+
     return uxReturn;
 }
 
@@ -3189,6 +3688,7 @@ static void prvDeleteTCB( TCB_t* pxTCB )
     above the vPortFree() calls.  The call is also used by ports/demos that
     want to allocate and clean RAM statically. */
     portCLEAN_UP_TCB( pxTCB );
+
     /* Free up the memory allocated by the scheduler for the task.  It is up
     to the task to free any memory allocated at the application level. */
 #if ( configUSE_NEWLIB_REENTRANT == 1 )
@@ -3196,21 +3696,41 @@ static void prvDeleteTCB( TCB_t* pxTCB )
         _reclaim_reent( &( pxTCB->xNewLib_reent ) );
     }
 #endif /* configUSE_NEWLIB_REENTRANT */
-#if( portUSING_MPU_WRAPPERS == 1 )
+
+#if( ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) && ( configSUPPORT_STATIC_ALLOCATION == 0 ) && ( portUSING_MPU_WRAPPERS == 0 ) )
     {
-        /* Only free the stack if it was allocated dynamically in the first
-        place. */
-        if ( pxTCB->xUsingStaticallyAllocatedStack == pdFALSE )
-        {
-            vPortFreeAligned( pxTCB->pxStack );
-        }
+        /* The task can only have been allocated dynamically - free both
+        the stack and TCB. */
+        vPortFree( pxTCB->pxStack );
+        vPortFree( pxTCB );
     }
-#else
+#elif( tskSTATIC_AND_DYNAMIC_ALLOCATION_POSSIBLE != 0 ) /*lint !e731 Macro has been consolidated for readability reasons. */
     {
-        vPortFreeAligned( pxTCB->pxStack );
+        /* The task could have been allocated statically or dynamically, so
+        check what was statically allocated before trying to free the
+        memory. */
+        if ( pxTCB->ucStaticallyAllocated == tskDYNAMICALLY_ALLOCATED_STACK_AND_TCB )
+        {
+            /* Both the stack and TCB were allocated dynamically, so both
+            must be freed. */
+            vPortFree( pxTCB->pxStack );
+            vPortFree( pxTCB );
+        }
+        else if ( pxTCB->ucStaticallyAllocated == tskSTATICALLY_ALLOCATED_STACK_ONLY )
+        {
+            /* Only the stack was statically allocated, so the TCB is the
+            only memory that must be freed. */
+            vPortFree( pxTCB );
+        }
+        else
+        {
+            /* Neither the stack nor the TCB were allocated dynamically, so
+            nothing needs to be freed. */
+            configASSERT( pxTCB->ucStaticallyAllocated == tskSTATICALLY_ALLOCATED_STACK_AND_TCB	);
+            mtCOVERAGE_TEST_MARKER();
+        }
     }
-#endif
-    vPortFree( pxTCB );
+#endif /* configSUPPORT_DYNAMIC_ALLOCATION */
 }
 
 #endif /* INCLUDE_vTaskDelete */
@@ -3235,7 +3755,7 @@ static void prvResetNextTaskUnblockTime( void )
         which the task at the head of the delayed list should be removed
         from the Blocked state. */
         ( pxTCB ) = ( TCB_t* ) listGET_OWNER_OF_HEAD_ENTRY( pxDelayedTaskList );
-        xNextTaskUnblockTime = listGET_LIST_ITEM_VALUE( &( ( pxTCB )->xGenericListItem ) );
+        xNextTaskUnblockTime = listGET_LIST_ITEM_VALUE( &( ( pxTCB )->xStateListItem ) );
     }
 }
 /*-----------------------------------------------------------*/
@@ -3245,10 +3765,12 @@ static void prvResetNextTaskUnblockTime( void )
 TaskHandle_t xTaskGetCurrentTaskHandle( void )
 {
     TaskHandle_t xReturn;
+
     /* A critical section is not required as this is not called from
     an interrupt and the current TCB will always be the same for any
     individual execution thread. */
     xReturn = pxCurrentTCB;
+
     return xReturn;
 }
 
@@ -3285,25 +3807,27 @@ BaseType_t xTaskGetSchedulerState( void )
 
 #if ( configUSE_MUTEXES == 1 )
 
-void vTaskPriorityInherit( TaskHandle_t const pxMutexHolder )
+BaseType_t xTaskPriorityInherit( TaskHandle_t const pxMutexHolder )
 {
-    TCB_t* const pxTCB = ( TCB_t* ) pxMutexHolder;
+    TCB_t* const pxMutexHolderTCB = ( TCB_t* ) pxMutexHolder;
+    BaseType_t xReturn = pdFALSE;
 
     /* If the mutex was given back by an interrupt while the queue was
-    locked then the mutex holder might now be NULL. */
+    locked then the mutex holder might now be NULL.  _RB_ Is this still
+    needed as interrupts can no longer use mutexes? */
     if ( pxMutexHolder != NULL )
     {
         /* If the holder of the mutex has a priority below the priority of
         the task attempting to obtain the mutex then it will temporarily
         inherit the priority of the task attempting to obtain the mutex. */
-        if ( pxTCB->uxPriority < pxCurrentTCB->uxPriority )
+        if ( pxMutexHolderTCB->uxPriority < pxCurrentTCB->uxPriority )
         {
             /* Adjust the mutex holder state to account for its new
             priority.  Only reset the event list item value if the value is
-            not	being used for anything else. */
-            if ( ( listGET_LIST_ITEM_VALUE( &( pxTCB->xEventListItem ) ) & taskEVENT_LIST_ITEM_VALUE_IN_USE ) == 0UL )
+            not being used for anything else. */
+            if ( ( listGET_LIST_ITEM_VALUE( &( pxMutexHolderTCB->xEventListItem ) ) & taskEVENT_LIST_ITEM_VALUE_IN_USE ) == 0UL )
             {
-                listSET_LIST_ITEM_VALUE( &( pxTCB->xEventListItem ), ( TickType_t ) configMAX_PRIORITIES - ( TickType_t ) pxCurrentTCB->uxPriority ); /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
+                listSET_LIST_ITEM_VALUE( &( pxMutexHolderTCB->xEventListItem ), ( TickType_t ) configMAX_PRIORITIES - ( TickType_t ) pxCurrentTCB->uxPriority ); /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
             }
             else
             {
@@ -3312,11 +3836,11 @@ void vTaskPriorityInherit( TaskHandle_t const pxMutexHolder )
 
             /* If the task being modified is in the ready state it will need
             to be moved into a new list. */
-            if ( listIS_CONTAINED_WITHIN( &( pxReadyTasksLists[ pxTCB->uxPriority ] ), &( pxTCB->xGenericListItem ) ) != pdFALSE )
+            if ( listIS_CONTAINED_WITHIN( &( pxReadyTasksLists[ pxMutexHolderTCB->uxPriority ] ), &( pxMutexHolderTCB->xStateListItem ) ) != pdFALSE )
             {
-                if ( uxListRemove( &( pxTCB->xGenericListItem ) ) == ( UBaseType_t ) 0 )
+                if ( uxListRemove( &( pxMutexHolderTCB->xStateListItem ) ) == ( UBaseType_t ) 0 )
                 {
-                    taskRESET_READY_PRIORITY( pxTCB->uxPriority );
+                    taskRESET_READY_PRIORITY( pxMutexHolderTCB->uxPriority );
                 }
                 else
                 {
@@ -3324,26 +3848,45 @@ void vTaskPriorityInherit( TaskHandle_t const pxMutexHolder )
                 }
 
                 /* Inherit the priority before being moved into the new list. */
-                pxTCB->uxPriority = pxCurrentTCB->uxPriority;
-                prvAddTaskToReadyList( pxTCB );
+                pxMutexHolderTCB->uxPriority = pxCurrentTCB->uxPriority;
+                prvAddTaskToReadyList( pxMutexHolderTCB );
             }
             else
             {
                 /* Just inherit the priority. */
-                pxTCB->uxPriority = pxCurrentTCB->uxPriority;
+                pxMutexHolderTCB->uxPriority = pxCurrentTCB->uxPriority;
             }
 
-            traceTASK_PRIORITY_INHERIT( pxTCB, pxCurrentTCB->uxPriority );
+            traceTASK_PRIORITY_INHERIT( pxMutexHolderTCB, pxCurrentTCB->uxPriority );
+
+            /* Inheritance occurred. */
+            xReturn = pdTRUE;
         }
         else
         {
-            mtCOVERAGE_TEST_MARKER();
+            if ( pxMutexHolderTCB->uxBasePriority < pxCurrentTCB->uxPriority )
+            {
+                /* The base priority of the mutex holder is lower than the
+                priority of the task attempting to take the mutex, but the
+                current priority of the mutex holder is not lower than the
+                priority of the task attempting to take the mutex.
+                Therefore the mutex holder must have already inherited a
+                priority, but inheritance would have occurred if that had
+                not been the case. */
+                xReturn = pdTRUE;
+            }
+            else
+            {
+                mtCOVERAGE_TEST_MARKER();
+            }
         }
     }
     else
     {
         mtCOVERAGE_TEST_MARKER();
     }
+
+    return xReturn;
 }
 
 #endif /* configUSE_MUTEXES */
@@ -3376,9 +3919,9 @@ BaseType_t xTaskPriorityDisinherit( TaskHandle_t const pxMutexHolder )
                 /* A task can only have an inherited priority if it holds
                 the mutex.  If the mutex is held by a task then it cannot be
                 given from an interrupt, and if a mutex is given by the
-                holding	task then it must be the running state task.  Remove
-                the	holding task from the ready	list. */
-                if ( uxListRemove( &( pxTCB->xGenericListItem ) ) == ( UBaseType_t ) 0 )
+                holding task then it must be the running state task.  Remove
+                the holding task from the ready list. */
+                if ( uxListRemove( &( pxTCB->xStateListItem ) ) == ( UBaseType_t ) 0 )
                 {
                     taskRESET_READY_PRIORITY( pxTCB->uxPriority );
                 }
@@ -3391,11 +3934,13 @@ BaseType_t xTaskPriorityDisinherit( TaskHandle_t const pxMutexHolder )
                 new	ready list. */
                 traceTASK_PRIORITY_DISINHERIT( pxTCB, pxTCB->uxBasePriority );
                 pxTCB->uxPriority = pxTCB->uxBasePriority;
+
                 /* Reset the event list item value.  It cannot be in use for
                 any other purpose if this task is running, and it must be
                 running to give back the mutex. */
                 listSET_LIST_ITEM_VALUE( &( pxTCB->xEventListItem ), ( TickType_t ) configMAX_PRIORITIES - ( TickType_t ) pxTCB->uxPriority ); /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
                 prvAddTaskToReadyList( pxTCB );
+
                 /* Return true to indicate that a context switch is required.
                 This is only actually required in the corner case whereby
                 multiple mutexes were held and the mutexes were given back
@@ -3427,6 +3972,108 @@ BaseType_t xTaskPriorityDisinherit( TaskHandle_t const pxMutexHolder )
 #endif /* configUSE_MUTEXES */
 /*-----------------------------------------------------------*/
 
+#if ( configUSE_MUTEXES == 1 )
+
+void vTaskPriorityDisinheritAfterTimeout( TaskHandle_t const pxMutexHolder, UBaseType_t uxHighestPriorityWaitingTask )
+{
+    TCB_t* const pxTCB = ( TCB_t* ) pxMutexHolder;
+    UBaseType_t uxPriorityUsedOnEntry, uxPriorityToUse;
+    const UBaseType_t uxOnlyOneMutexHeld = ( UBaseType_t ) 1;
+
+    if ( pxMutexHolder != NULL )
+    {
+        /* If pxMutexHolder is not NULL then the holder must hold at least
+        one mutex. */
+        configASSERT( pxTCB->uxMutexesHeld );
+
+        /* Determine the priority to which the priority of the task that
+        holds the mutex should be set.  This will be the greater of the
+        holding task's base priority and the priority of the highest
+        priority task that is waiting to obtain the mutex. */
+        if ( pxTCB->uxBasePriority < uxHighestPriorityWaitingTask )
+        {
+            uxPriorityToUse = uxHighestPriorityWaitingTask;
+        }
+        else
+        {
+            uxPriorityToUse = pxTCB->uxBasePriority;
+        }
+
+        /* Does the priority need to change? */
+        if ( pxTCB->uxPriority != uxPriorityToUse )
+        {
+            /* Only disinherit if no other mutexes are held.  This is a
+            simplification in the priority inheritance implementation.  If
+            the task that holds the mutex is also holding other mutexes then
+            the other mutexes may have caused the priority inheritance. */
+            if ( pxTCB->uxMutexesHeld == uxOnlyOneMutexHeld )
+            {
+                /* If a task has timed out because it already holds the
+                mutex it was trying to obtain then it cannot of inherited
+                its own priority. */
+                configASSERT( pxTCB != pxCurrentTCB );
+
+                /* Disinherit the priority, remembering the previous
+                priority to facilitate determining the subject task's
+                state. */
+                traceTASK_PRIORITY_DISINHERIT( pxTCB, pxTCB->uxBasePriority );
+                uxPriorityUsedOnEntry = pxTCB->uxPriority;
+                pxTCB->uxPriority = uxPriorityToUse;
+
+                /* Only reset the event list item value if the value is not
+                being used for anything else. */
+                if ( ( listGET_LIST_ITEM_VALUE( &( pxTCB->xEventListItem ) ) & taskEVENT_LIST_ITEM_VALUE_IN_USE ) == 0UL )
+                {
+                    listSET_LIST_ITEM_VALUE( &( pxTCB->xEventListItem ), ( TickType_t ) configMAX_PRIORITIES - ( TickType_t ) uxPriorityToUse ); /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
+                }
+                else
+                {
+                    mtCOVERAGE_TEST_MARKER();
+                }
+
+                /* If the running task is not the task that holds the mutex
+                then the task that holds the mutex could be in either the
+                Ready, Blocked or Suspended states.  Only remove the task
+                from its current state list if it is in the Ready state as
+                the task's priority is going to change and there is one
+                Ready list per priority. */
+                if ( listIS_CONTAINED_WITHIN( &( pxReadyTasksLists[ uxPriorityUsedOnEntry ] ), &( pxTCB->xStateListItem ) ) != pdFALSE )
+                {
+                    if ( uxListRemove( &( pxTCB->xStateListItem ) ) == ( UBaseType_t ) 0 )
+                    {
+                        taskRESET_READY_PRIORITY( pxTCB->uxPriority );
+                    }
+                    else
+                    {
+                        mtCOVERAGE_TEST_MARKER();
+                    }
+
+                    prvAddTaskToReadyList( pxTCB );
+                }
+                else
+                {
+                    mtCOVERAGE_TEST_MARKER();
+                }
+            }
+            else
+            {
+                mtCOVERAGE_TEST_MARKER();
+            }
+        }
+        else
+        {
+            mtCOVERAGE_TEST_MARKER();
+        }
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+}
+
+#endif /* configUSE_MUTEXES */
+/*-----------------------------------------------------------*/
+
 #if ( portCRITICAL_NESTING_IN_TCB == 1 )
 
 void vTaskEnterCritical( void )
@@ -3495,6 +4142,7 @@ void vTaskExitCritical( void )
 static char* prvWriteNameToBuffer( char* pcBuffer, const char* pcTaskName )
 {
     size_t x;
+
     /* Start by copying the entire string. */
     strcpy( pcBuffer, pcTaskName );
 
@@ -3507,6 +4155,7 @@ static char* prvWriteNameToBuffer( char* pcBuffer, const char* pcTaskName )
 
     /* Terminate. */
     pcBuffer[ x ] = 0x00;
+
     /* Return the new end of string. */
     return &( pcBuffer[ x ] );
 }
@@ -3514,13 +4163,14 @@ static char* prvWriteNameToBuffer( char* pcBuffer, const char* pcTaskName )
 #endif /* ( configUSE_TRACE_FACILITY == 1 ) && ( configUSE_STATS_FORMATTING_FUNCTIONS > 0 ) */
 /*-----------------------------------------------------------*/
 
-#if ( ( configUSE_TRACE_FACILITY == 1 ) && ( configUSE_STATS_FORMATTING_FUNCTIONS > 0 ) )
+#if ( ( configUSE_TRACE_FACILITY == 1 ) && ( configUSE_STATS_FORMATTING_FUNCTIONS > 0 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) )
 
 void vTaskList( char* pcWriteBuffer )
 {
     TaskStatus_t* pxTaskStatusArray;
     volatile UBaseType_t uxArraySize, x;
     char cStatus;
+
     /*
      * PLEASE NOTE:
      *
@@ -3544,12 +4194,18 @@ void vTaskList( char* pcWriteBuffer )
      * directly to get access to raw stats data, rather than indirectly
      * through a call to vTaskList().
      */
+
+
     /* Make sure the write buffer does not contain a string. */
     *pcWriteBuffer = 0x00;
+
     /* Take a snapshot of the number of tasks in case it changes while this
     function is executing. */
     uxArraySize = uxCurrentNumberOfTasks;
-    /* Allocate an array index for each task. */
+
+    /* Allocate an array index for each task.  NOTE!  if
+    configSUPPORT_DYNAMIC_ALLOCATION is set to 0 then pvPortMalloc() will
+    equate to NULL. */
     pxTaskStatusArray = pvPortMalloc( uxCurrentNumberOfTasks * sizeof( TaskStatus_t ) );
 
     if ( pxTaskStatusArray != NULL )
@@ -3562,6 +4218,10 @@ void vTaskList( char* pcWriteBuffer )
         {
             switch ( pxTaskStatusArray[ x ].eCurrentState )
             {
+                case eRunning:
+                    cStatus = tskRUNNING_CHAR;
+                    break;
+
                 case eReady:
                     cStatus = tskREADY_CHAR;
                     break;
@@ -3587,12 +4247,14 @@ void vTaskList( char* pcWriteBuffer )
             /* Write the task name to the string, padding with spaces so it
             can be printed in tabular form more easily. */
             pcWriteBuffer = prvWriteNameToBuffer( pcWriteBuffer, pxTaskStatusArray[ x ].pcTaskName );
+
             /* Write the rest of the string. */
             sprintf( pcWriteBuffer, "\t%c\t%u\t%u\t%u\r\n", cStatus, ( unsigned int ) pxTaskStatusArray[ x ].uxCurrentPriority, ( unsigned int ) pxTaskStatusArray[ x ].usStackHighWaterMark, ( unsigned int ) pxTaskStatusArray[ x ].xTaskNumber );
             pcWriteBuffer += strlen( pcWriteBuffer );
         }
 
-        /* Free the array again. */
+        /* Free the array again.  NOTE!  If configSUPPORT_DYNAMIC_ALLOCATION
+        is 0 then vPortFree() will be #defined to nothing. */
         vPortFree( pxTaskStatusArray );
     }
     else
@@ -3601,21 +4263,23 @@ void vTaskList( char* pcWriteBuffer )
     }
 }
 
-#endif /* ( ( configUSE_TRACE_FACILITY == 1 ) && ( configUSE_STATS_FORMATTING_FUNCTIONS > 0 ) ) */
+#endif /* ( ( configUSE_TRACE_FACILITY == 1 ) && ( configUSE_STATS_FORMATTING_FUNCTIONS > 0 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) ) */
 /*----------------------------------------------------------*/
 
-#if ( ( configGENERATE_RUN_TIME_STATS == 1 ) && ( configUSE_STATS_FORMATTING_FUNCTIONS > 0 ) )
+#if ( ( configGENERATE_RUN_TIME_STATS == 1 ) && ( configUSE_STATS_FORMATTING_FUNCTIONS > 0 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) )
 
 void vTaskGetRunTimeStats( char* pcWriteBuffer )
 {
     TaskStatus_t* pxTaskStatusArray;
     volatile UBaseType_t uxArraySize, x;
     uint32_t ulTotalTime, ulStatsAsPercentage;
+
 #if( configUSE_TRACE_FACILITY != 1 )
     {
 #error configUSE_TRACE_FACILITY must also be set to 1 in FreeRTOSConfig.h to use vTaskGetRunTimeStats().
     }
 #endif
+
     /*
      * PLEASE NOTE:
      *
@@ -3640,18 +4304,24 @@ void vTaskGetRunTimeStats( char* pcWriteBuffer )
      * directly to get access to raw stats data, rather than indirectly
      * through a call to vTaskGetRunTimeStats().
      */
+
     /* Make sure the write buffer does not contain a string. */
     *pcWriteBuffer = 0x00;
+
     /* Take a snapshot of the number of tasks in case it changes while this
     function is executing. */
     uxArraySize = uxCurrentNumberOfTasks;
-    /* Allocate an array index for each task. */
+
+    /* Allocate an array index for each task.  NOTE!  If
+    configSUPPORT_DYNAMIC_ALLOCATION is set to 0 then pvPortMalloc() will
+    equate to NULL. */
     pxTaskStatusArray = pvPortMalloc( uxCurrentNumberOfTasks * sizeof( TaskStatus_t ) );
 
     if ( pxTaskStatusArray != NULL )
     {
         /* Generate the (binary) data. */
         uxArraySize = uxTaskGetSystemState( pxTaskStatusArray, uxArraySize, &ulTotalTime );
+
         /* For percentage calculations. */
         ulTotalTime /= 100UL;
 
@@ -3665,6 +4335,7 @@ void vTaskGetRunTimeStats( char* pcWriteBuffer )
                 This will always be rounded down to the nearest integer.
                 ulTotalRunTimeDiv100 has already been divided by 100. */
                 ulStatsAsPercentage = pxTaskStatusArray[ x ].ulRunTimeCounter / ulTotalTime;
+
                 /* Write the task name to the string, padding with
                 spaces so it can be printed in tabular form more
                 easily. */
@@ -3709,7 +4380,8 @@ void vTaskGetRunTimeStats( char* pcWriteBuffer )
             mtCOVERAGE_TEST_MARKER();
         }
 
-        /* Free the array again. */
+        /* Free the array again.  NOTE!  If configSUPPORT_DYNAMIC_ALLOCATION
+        is 0 then vPortFree() will be #defined to nothing. */
         vPortFree( pxTaskStatusArray );
     }
     else
@@ -3718,16 +4390,19 @@ void vTaskGetRunTimeStats( char* pcWriteBuffer )
     }
 }
 
-#endif /* ( ( configGENERATE_RUN_TIME_STATS == 1 ) && ( configUSE_STATS_FORMATTING_FUNCTIONS > 0 ) ) */
+#endif /* ( ( configGENERATE_RUN_TIME_STATS == 1 ) && ( configUSE_STATS_FORMATTING_FUNCTIONS > 0 ) && ( configSUPPORT_STATIC_ALLOCATION == 1 ) ) */
 /*-----------------------------------------------------------*/
 
 TickType_t uxTaskResetEventItemValue( void )
 {
     TickType_t uxReturn;
+
     uxReturn = listGET_LIST_ITEM_VALUE( &( pxCurrentTCB->xEventListItem ) );
+
     /* Reset the event list item to its normal value - so it can be used with
     queues and semaphores. */
     listSET_LIST_ITEM_VALUE( &( pxCurrentTCB->xEventListItem ), ( ( TickType_t ) configMAX_PRIORITIES - ( TickType_t ) pxCurrentTCB->uxPriority ) ); /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
+
     return uxReturn;
 }
 /*-----------------------------------------------------------*/
@@ -3753,63 +4428,21 @@ void* pvTaskIncrementMutexHeldCount( void )
 
 uint32_t ulTaskNotifyTake( BaseType_t xClearCountOnExit, TickType_t xTicksToWait )
 {
-    TickType_t xTimeToWake;
     uint32_t ulReturn;
+
     taskENTER_CRITICAL();
     {
         /* Only block if the notification count is not already non-zero. */
         if ( pxCurrentTCB->ulNotifiedValue == 0UL )
         {
             /* Mark this task as waiting for a notification. */
-            pxCurrentTCB->eNotifyState = eWaitingNotification;
+            pxCurrentTCB->ucNotifyState = taskWAITING_NOTIFICATION;
 
             if ( xTicksToWait > ( TickType_t ) 0 )
             {
-                /* The task is going to block.  First it must be removed
-                from the ready list. */
-                if ( uxListRemove( &( pxCurrentTCB->xGenericListItem ) ) == ( UBaseType_t ) 0 )
-                {
-                    /* The current task must be in a ready list, so there is
-                    no need to check, and the port reset macro can be called
-                    directly. */
-                    portRESET_READY_PRIORITY( pxCurrentTCB->uxPriority, uxTopReadyPriority );
-                }
-                else
-                {
-                    mtCOVERAGE_TEST_MARKER();
-                }
-
-#if ( INCLUDE_vTaskSuspend == 1 )
-                {
-                    if ( xTicksToWait == portMAX_DELAY )
-                    {
-                        /* Add the task to the suspended task list instead
-                        of a delayed task list to ensure the task is not
-                        woken by a timing event.  It will block
-                        indefinitely. */
-                        vListInsertEnd( &xSuspendedTaskList, &( pxCurrentTCB->xGenericListItem ) );
-                    }
-                    else
-                    {
-                        /* Calculate the time at which the task should be
-                        woken if no notification events occur.  This may
-                        overflow but this doesn't matter, the scheduler will
-                        handle it. */
-                        xTimeToWake = xTickCount + xTicksToWait;
-                        prvAddCurrentTaskToDelayedList( xTimeToWake );
-                    }
-                }
-#else /* INCLUDE_vTaskSuspend */
-                {
-                    /* Calculate the time at which the task should be
-                    woken if the event does not occur.  This may
-                    overflow but this doesn't matter, the scheduler will
-                    handle it. */
-                    xTimeToWake = xTickCount + xTicksToWait;
-                    prvAddCurrentTaskToDelayedList( xTimeToWake );
-                }
-#endif /* INCLUDE_vTaskSuspend */
+                prvAddCurrentTaskToDelayedList( xTicksToWait, pdTRUE );
                 traceTASK_NOTIFY_TAKE_BLOCK();
+
                 /* All ports are written to allow a yield in a critical
                 section (some will yield immediately, others wait until the
                 critical section exits) - but it is not something that
@@ -3827,6 +4460,7 @@ uint32_t ulTaskNotifyTake( BaseType_t xClearCountOnExit, TickType_t xTicksToWait
         }
     }
     taskEXIT_CRITICAL();
+
     taskENTER_CRITICAL();
     {
         traceTASK_NOTIFY_TAKE();
@@ -3840,7 +4474,7 @@ uint32_t ulTaskNotifyTake( BaseType_t xClearCountOnExit, TickType_t xTicksToWait
             }
             else
             {
-                ( pxCurrentTCB->ulNotifiedValue )--;
+                pxCurrentTCB->ulNotifiedValue = ulReturn - ( uint32_t ) 1;
             }
         }
         else
@@ -3848,9 +4482,10 @@ uint32_t ulTaskNotifyTake( BaseType_t xClearCountOnExit, TickType_t xTicksToWait
             mtCOVERAGE_TEST_MARKER();
         }
 
-        pxCurrentTCB->eNotifyState = eNotWaitingNotification;
+        pxCurrentTCB->ucNotifyState = taskNOT_WAITING_NOTIFICATION;
     }
     taskEXIT_CRITICAL();
+
     return ulReturn;
 }
 
@@ -3861,67 +4496,26 @@ uint32_t ulTaskNotifyTake( BaseType_t xClearCountOnExit, TickType_t xTicksToWait
 
 BaseType_t xTaskNotifyWait( uint32_t ulBitsToClearOnEntry, uint32_t ulBitsToClearOnExit, uint32_t* pulNotificationValue, TickType_t xTicksToWait )
 {
-    TickType_t xTimeToWake;
     BaseType_t xReturn;
+
     taskENTER_CRITICAL();
     {
         /* Only block if a notification is not already pending. */
-        if ( pxCurrentTCB->eNotifyState != eNotified )
+        if ( pxCurrentTCB->ucNotifyState != taskNOTIFICATION_RECEIVED )
         {
             /* Clear bits in the task's notification value as bits may get
             set	by the notifying task or interrupt.  This can be used to
             clear the value to zero. */
             pxCurrentTCB->ulNotifiedValue &= ~ulBitsToClearOnEntry;
+
             /* Mark this task as waiting for a notification. */
-            pxCurrentTCB->eNotifyState = eWaitingNotification;
+            pxCurrentTCB->ucNotifyState = taskWAITING_NOTIFICATION;
 
             if ( xTicksToWait > ( TickType_t ) 0 )
             {
-                /* The task is going to block.  First it must be removed
-                from the	ready list. */
-                if ( uxListRemove( &( pxCurrentTCB->xGenericListItem ) ) == ( UBaseType_t ) 0 )
-                {
-                    /* The current task must be in a ready list, so there is
-                    no need to check, and the port reset macro can be called
-                    directly. */
-                    portRESET_READY_PRIORITY( pxCurrentTCB->uxPriority, uxTopReadyPriority );
-                }
-                else
-                {
-                    mtCOVERAGE_TEST_MARKER();
-                }
-
-#if ( INCLUDE_vTaskSuspend == 1 )
-                {
-                    if ( xTicksToWait == portMAX_DELAY )
-                    {
-                        /* Add the task to the suspended task list instead
-                        of a delayed task list to ensure the task is not
-                        woken by a timing event.  It will block
-                        indefinitely. */
-                        vListInsertEnd( &xSuspendedTaskList, &( pxCurrentTCB->xGenericListItem ) );
-                    }
-                    else
-                    {
-                        /* Calculate the time at which the task should be
-                        woken if no notification events occur.  This may
-                        overflow but this doesn't matter, the scheduler will
-                        handle it. */
-                        xTimeToWake = xTickCount + xTicksToWait;
-                        prvAddCurrentTaskToDelayedList( xTimeToWake );
-                    }
-                }
-#else /* INCLUDE_vTaskSuspend */
-                {
-                    /* Calculate the time at which the task should be
-                    woken if the event does not occur.  This may
-                    overflow but this doesn't matter, the scheduler will
-                    handle it. */
-                    xTimeToWake = xTickCount + xTicksToWait;
-                    prvAddCurrentTaskToDelayedList( xTimeToWake );
-                }
-#endif /* INCLUDE_vTaskSuspend */
+                prvAddCurrentTaskToDelayedList( xTicksToWait, pdTRUE );
                 traceTASK_NOTIFY_WAIT_BLOCK();
+
                 /* All ports are written to allow a yield in a critical
                 section (some will yield immediately, others wait until the
                 critical section exits) - but it is not something that
@@ -3939,6 +4533,7 @@ BaseType_t xTaskNotifyWait( uint32_t ulBitsToClearOnEntry, uint32_t ulBitsToClea
         }
     }
     taskEXIT_CRITICAL();
+
     taskENTER_CRITICAL();
     {
         traceTASK_NOTIFY_WAIT();
@@ -3950,11 +4545,11 @@ BaseType_t xTaskNotifyWait( uint32_t ulBitsToClearOnEntry, uint32_t ulBitsToClea
             *pulNotificationValue = pxCurrentTCB->ulNotifiedValue;
         }
 
-        /* If eNotifyValue is set then either the task never entered the
+        /* If ucNotifyValue is set then either the task never entered the
         blocked state (because a notification was already pending) or the
         task unblocked because of a notification.  Otherwise the task
         unblocked because of a timeout. */
-        if ( pxCurrentTCB->eNotifyState == eWaitingNotification )
+        if ( pxCurrentTCB->ucNotifyState != taskNOTIFICATION_RECEIVED )
         {
             /* A notification was not received. */
             xReturn = pdFALSE;
@@ -3967,9 +4562,10 @@ BaseType_t xTaskNotifyWait( uint32_t ulBitsToClearOnEntry, uint32_t ulBitsToClea
             xReturn = pdTRUE;
         }
 
-        pxCurrentTCB->eNotifyState = eNotWaitingNotification;
+        pxCurrentTCB->ucNotifyState = taskNOT_WAITING_NOTIFICATION;
     }
     taskEXIT_CRITICAL();
+
     return xReturn;
 }
 
@@ -3981,10 +4577,12 @@ BaseType_t xTaskNotifyWait( uint32_t ulBitsToClearOnEntry, uint32_t ulBitsToClea
 BaseType_t xTaskGenericNotify( TaskHandle_t xTaskToNotify, uint32_t ulValue, eNotifyAction eAction, uint32_t* pulPreviousNotificationValue )
 {
     TCB_t* pxTCB;
-    eNotifyValue eOriginalNotifyState;
     BaseType_t xReturn = pdPASS;
+    uint8_t ucOriginalNotifyState;
+
     configASSERT( xTaskToNotify );
     pxTCB = ( TCB_t* ) xTaskToNotify;
+
     taskENTER_CRITICAL();
     {
         if ( pulPreviousNotificationValue != NULL )
@@ -3992,8 +4590,9 @@ BaseType_t xTaskGenericNotify( TaskHandle_t xTaskToNotify, uint32_t ulValue, eNo
             *pulPreviousNotificationValue = pxTCB->ulNotifiedValue;
         }
 
-        eOriginalNotifyState = pxTCB->eNotifyState;
-        pxTCB->eNotifyState = eNotified;
+        ucOriginalNotifyState = pxTCB->ucNotifyState;
+
+        pxTCB->ucNotifyState = taskNOTIFICATION_RECEIVED;
 
         switch ( eAction )
         {
@@ -4010,7 +4609,7 @@ BaseType_t xTaskGenericNotify( TaskHandle_t xTaskToNotify, uint32_t ulValue, eNo
                 break;
 
             case eSetValueWithoutOverwrite :
-                if ( eOriginalNotifyState != eNotified )
+                if ( ucOriginalNotifyState != taskNOTIFICATION_RECEIVED )
                 {
                     pxTCB->ulNotifiedValue = ulValue;
                 }
@@ -4032,12 +4631,14 @@ BaseType_t xTaskGenericNotify( TaskHandle_t xTaskToNotify, uint32_t ulValue, eNo
 
         /* If the task is in the blocked state specifically to wait for a
         notification then unblock it now. */
-        if ( eOriginalNotifyState == eWaitingNotification )
+        if ( ucOriginalNotifyState == taskWAITING_NOTIFICATION )
         {
-            ( void ) uxListRemove( &( pxTCB->xGenericListItem ) );
+            ( void ) uxListRemove( &( pxTCB->xStateListItem ) );
             prvAddTaskToReadyList( pxTCB );
+
             /* The task should not have been on an event list. */
             configASSERT( listLIST_ITEM_CONTAINER( &( pxTCB->xEventListItem ) ) == NULL );
+
 #if( configUSE_TICKLESS_IDLE != 0 )
             {
                 /* If a task is blocked waiting for a notification then
@@ -4071,6 +4672,7 @@ BaseType_t xTaskGenericNotify( TaskHandle_t xTaskToNotify, uint32_t ulValue, eNo
         }
     }
     taskEXIT_CRITICAL();
+
     return xReturn;
 }
 
@@ -4082,10 +4684,12 @@ BaseType_t xTaskGenericNotify( TaskHandle_t xTaskToNotify, uint32_t ulValue, eNo
 BaseType_t xTaskGenericNotifyFromISR( TaskHandle_t xTaskToNotify, uint32_t ulValue, eNotifyAction eAction, uint32_t* pulPreviousNotificationValue, BaseType_t* pxHigherPriorityTaskWoken )
 {
     TCB_t* pxTCB;
-    eNotifyValue eOriginalNotifyState;
+    uint8_t ucOriginalNotifyState;
     BaseType_t xReturn = pdPASS;
     UBaseType_t uxSavedInterruptStatus;
+
     configASSERT( xTaskToNotify );
+
     /* RTOS ports that support interrupt nesting have the concept of a
     maximum	system call (or maximum API call) interrupt priority.
     Interrupts that are	above the maximum system call priority are keep
@@ -4103,7 +4707,9 @@ BaseType_t xTaskGenericNotifyFromISR( TaskHandle_t xTaskToNotify, uint32_t ulVal
     provided on the following link:
     http://www.freertos.org/RTOS-Cortex-M3-M4.html */
     portASSERT_IF_INTERRUPT_PRIORITY_INVALID();
+
     pxTCB = ( TCB_t* ) xTaskToNotify;
+
     uxSavedInterruptStatus = portSET_INTERRUPT_MASK_FROM_ISR();
     {
         if ( pulPreviousNotificationValue != NULL )
@@ -4111,8 +4717,8 @@ BaseType_t xTaskGenericNotifyFromISR( TaskHandle_t xTaskToNotify, uint32_t ulVal
             *pulPreviousNotificationValue = pxTCB->ulNotifiedValue;
         }
 
-        eOriginalNotifyState = pxTCB->eNotifyState;
-        pxTCB->eNotifyState = eNotified;
+        ucOriginalNotifyState = pxTCB->ucNotifyState;
+        pxTCB->ucNotifyState = taskNOTIFICATION_RECEIVED;
 
         switch ( eAction )
         {
@@ -4129,7 +4735,7 @@ BaseType_t xTaskGenericNotifyFromISR( TaskHandle_t xTaskToNotify, uint32_t ulVal
                 break;
 
             case eSetValueWithoutOverwrite :
-                if ( eOriginalNotifyState != eNotified )
+                if ( ucOriginalNotifyState != taskNOTIFICATION_RECEIVED )
                 {
                     pxTCB->ulNotifiedValue = ulValue;
                 }
@@ -4151,14 +4757,14 @@ BaseType_t xTaskGenericNotifyFromISR( TaskHandle_t xTaskToNotify, uint32_t ulVal
 
         /* If the task is in the blocked state specifically to wait for a
         notification then unblock it now. */
-        if ( eOriginalNotifyState == eWaitingNotification )
+        if ( ucOriginalNotifyState == taskWAITING_NOTIFICATION )
         {
             /* The task should not have been on an event list. */
             configASSERT( listLIST_ITEM_CONTAINER( &( pxTCB->xEventListItem ) ) == NULL );
 
             if ( uxSchedulerSuspended == ( UBaseType_t ) pdFALSE )
             {
-                ( void ) uxListRemove( &( pxTCB->xGenericListItem ) );
+                ( void ) uxListRemove( &( pxTCB->xStateListItem ) );
                 prvAddTaskToReadyList( pxTCB );
             }
             else
@@ -4176,6 +4782,13 @@ BaseType_t xTaskGenericNotifyFromISR( TaskHandle_t xTaskToNotify, uint32_t ulVal
                 {
                     *pxHigherPriorityTaskWoken = pdTRUE;
                 }
+                else
+                {
+                    /* Mark that a yield is pending in case the user is not
+                    using the "xHigherPriorityTaskWoken" parameter to an ISR
+                    safe FreeRTOS function. */
+                    xYieldPending = pdTRUE;
+                }
             }
             else
             {
@@ -4184,6 +4797,7 @@ BaseType_t xTaskGenericNotifyFromISR( TaskHandle_t xTaskToNotify, uint32_t ulVal
         }
     }
     portCLEAR_INTERRUPT_MASK_FROM_ISR( uxSavedInterruptStatus );
+
     return xReturn;
 }
 
@@ -4195,9 +4809,11 @@ BaseType_t xTaskGenericNotifyFromISR( TaskHandle_t xTaskToNotify, uint32_t ulVal
 void vTaskNotifyGiveFromISR( TaskHandle_t xTaskToNotify, BaseType_t* pxHigherPriorityTaskWoken )
 {
     TCB_t* pxTCB;
-    eNotifyValue eOriginalNotifyState;
+    uint8_t ucOriginalNotifyState;
     UBaseType_t uxSavedInterruptStatus;
+
     configASSERT( xTaskToNotify );
+
     /* RTOS ports that support interrupt nesting have the concept of a
     maximum	system call (or maximum API call) interrupt priority.
     Interrupts that are	above the maximum system call priority are keep
@@ -4215,26 +4831,30 @@ void vTaskNotifyGiveFromISR( TaskHandle_t xTaskToNotify, BaseType_t* pxHigherPri
     provided on the following link:
     http://www.freertos.org/RTOS-Cortex-M3-M4.html */
     portASSERT_IF_INTERRUPT_PRIORITY_INVALID();
+
     pxTCB = ( TCB_t* ) xTaskToNotify;
+
     uxSavedInterruptStatus = portSET_INTERRUPT_MASK_FROM_ISR();
     {
-        eOriginalNotifyState = pxTCB->eNotifyState;
-        pxTCB->eNotifyState = eNotified;
+        ucOriginalNotifyState = pxTCB->ucNotifyState;
+        pxTCB->ucNotifyState = taskNOTIFICATION_RECEIVED;
+
         /* 'Giving' is equivalent to incrementing a count in a counting
         semaphore. */
         ( pxTCB->ulNotifiedValue )++;
+
         traceTASK_NOTIFY_GIVE_FROM_ISR();
 
         /* If the task is in the blocked state specifically to wait for a
         notification then unblock it now. */
-        if ( eOriginalNotifyState == eWaitingNotification )
+        if ( ucOriginalNotifyState == taskWAITING_NOTIFICATION )
         {
             /* The task should not have been on an event list. */
             configASSERT( listLIST_ITEM_CONTAINER( &( pxTCB->xEventListItem ) ) == NULL );
 
             if ( uxSchedulerSuspended == ( UBaseType_t ) pdFALSE )
             {
-                ( void ) uxListRemove( &( pxTCB->xGenericListItem ) );
+                ( void ) uxListRemove( &( pxTCB->xStateListItem ) );
                 prvAddTaskToReadyList( pxTCB );
             }
             else
@@ -4252,6 +4872,13 @@ void vTaskNotifyGiveFromISR( TaskHandle_t xTaskToNotify, BaseType_t* pxHigherPri
                 {
                     *pxHigherPriorityTaskWoken = pdTRUE;
                 }
+                else
+                {
+                    /* Mark that a yield is pending in case the user is not
+                    using the "xHigherPriorityTaskWoken" parameter in an ISR
+                    safe FreeRTOS function. */
+                    xYieldPending = pdTRUE;
+                }
             }
             else
             {
@@ -4272,15 +4899,16 @@ BaseType_t xTaskNotifyStateClear( TaskHandle_t xTask )
 {
     TCB_t* pxTCB;
     BaseType_t xReturn;
-    pxTCB = ( TCB_t* ) xTask;
+
     /* If null is passed in here then it is the calling task that is having
     its notification state cleared. */
-    pxTCB = prvGetTCBFromHandle( pxTCB );
+    pxTCB = prvGetTCBFromHandle( xTask );
+
     taskENTER_CRITICAL();
     {
-        if ( pxTCB->eNotifyState == eNotified )
+        if ( pxTCB->ucNotifyState == taskNOTIFICATION_RECEIVED )
         {
-            pxTCB->eNotifyState = eNotWaitingNotification;
+            pxTCB->ucNotifyState = taskNOT_WAITING_NOTIFICATION;
             xReturn = pdPASS;
         }
         else
@@ -4289,12 +4917,145 @@ BaseType_t xTaskNotifyStateClear( TaskHandle_t xTask )
         }
     }
     taskEXIT_CRITICAL();
+
     return xReturn;
 }
 
 #endif /* configUSE_TASK_NOTIFICATIONS */
+/*-----------------------------------------------------------*/
+
+
+static void prvAddCurrentTaskToDelayedList( TickType_t xTicksToWait, const BaseType_t xCanBlockIndefinitely )
+{
+    TickType_t xTimeToWake;
+    const TickType_t xConstTickCount = xTickCount;
+
+#if( INCLUDE_xTaskAbortDelay == 1 )
+    {
+        /* About to enter a delayed list, so ensure the ucDelayAborted flag is
+        reset to pdFALSE so it can be detected as having been set to pdTRUE
+        when the task leaves the Blocked state. */
+        pxCurrentTCB->ucDelayAborted = pdFALSE;
+    }
+#endif
+
+    /* Remove the task from the ready list before adding it to the blocked list
+    as the same list item is used for both lists. */
+    if ( uxListRemove( &( pxCurrentTCB->xStateListItem ) ) == ( UBaseType_t ) 0 )
+    {
+        /* The current task must be in a ready list, so there is no need to
+        check, and the port reset macro can be called directly. */
+        portRESET_READY_PRIORITY( pxCurrentTCB->uxPriority, uxTopReadyPriority );
+    }
+    else
+    {
+        mtCOVERAGE_TEST_MARKER();
+    }
+
+#if ( INCLUDE_vTaskSuspend == 1 )
+    {
+        if ( ( xTicksToWait == portMAX_DELAY ) && ( xCanBlockIndefinitely != pdFALSE ) )
+        {
+            /* Add the task to the suspended task list instead of a delayed task
+            list to ensure it is not woken by a timing event.  It will block
+            indefinitely. */
+            vListInsertEnd( &xSuspendedTaskList, &( pxCurrentTCB->xStateListItem ) );
+        }
+        else
+        {
+            /* Calculate the time at which the task should be woken if the event
+            does not occur.  This may overflow but this doesn't matter, the
+            kernel will manage it correctly. */
+            xTimeToWake = xConstTickCount + xTicksToWait;
+
+            /* The list item will be inserted in wake time order. */
+            listSET_LIST_ITEM_VALUE( &( pxCurrentTCB->xStateListItem ), xTimeToWake );
+
+            if ( xTimeToWake < xConstTickCount )
+            {
+                /* Wake time has overflowed.  Place this item in the overflow
+                list. */
+                vListInsert( pxOverflowDelayedTaskList, &( pxCurrentTCB->xStateListItem ) );
+            }
+            else
+            {
+                /* The wake time has not overflowed, so the current block list
+                is used. */
+                vListInsert( pxDelayedTaskList, &( pxCurrentTCB->xStateListItem ) );
+
+                /* If the task entering the blocked state was placed at the
+                head of the list of blocked tasks then xNextTaskUnblockTime
+                needs to be updated too. */
+                if ( xTimeToWake < xNextTaskUnblockTime )
+                {
+                    xNextTaskUnblockTime = xTimeToWake;
+                }
+                else
+                {
+                    mtCOVERAGE_TEST_MARKER();
+                }
+            }
+        }
+    }
+#else /* INCLUDE_vTaskSuspend */
+    {
+        /* Calculate the time at which the task should be woken if the event
+        does not occur.  This may overflow but this doesn't matter, the kernel
+        will manage it correctly. */
+        xTimeToWake = xConstTickCount + xTicksToWait;
+
+        /* The list item will be inserted in wake time order. */
+        listSET_LIST_ITEM_VALUE( &( pxCurrentTCB->xStateListItem ), xTimeToWake );
+
+        if ( xTimeToWake < xConstTickCount )
+        {
+            /* Wake time has overflowed.  Place this item in the overflow list. */
+            vListInsert( pxOverflowDelayedTaskList, &( pxCurrentTCB->xStateListItem ) );
+        }
+        else
+        {
+            /* The wake time has not overflowed, so the current block list is used. */
+            vListInsert( pxDelayedTaskList, &( pxCurrentTCB->xStateListItem ) );
+
+            /* If the task entering the blocked state was placed at the head of the
+            list of blocked tasks then xNextTaskUnblockTime needs to be updated
+            too. */
+            if ( xTimeToWake < xNextTaskUnblockTime )
+            {
+                xNextTaskUnblockTime = xTimeToWake;
+            }
+            else
+            {
+                mtCOVERAGE_TEST_MARKER();
+            }
+        }
+
+        /* Avoid compiler warning when INCLUDE_vTaskSuspend is not 1. */
+        ( void ) xCanBlockIndefinitely;
+    }
+#endif /* INCLUDE_vTaskSuspend */
+}
+
+/* Code below here allows additional code to be inserted into this source file,
+especially where access to file scope functions and data is needed (for example
+when performing module tests). */
 
 #ifdef FREERTOS_MODULE_TEST
 #include "tasks_test_access_functions.h"
 #endif
 
+
+#if( configINCLUDE_FREERTOS_TASK_C_ADDITIONS_H == 1 )
+
+#include "freertos_tasks_c_additions.h"
+
+static void freertos_tasks_c_additions_init( void )
+{
+#ifdef FREERTOS_TASKS_C_ADDITIONS_INIT
+    FREERTOS_TASKS_C_ADDITIONS_INIT();
+#endif
+}
+
+#endif
+
+
diff --git a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/timers.c b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/timers.c
index f81a45f3..257302a5 100644
--- a/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/timers.c
+++ b/EpsilonLights/Middlewares/Third_Party/FreeRTOS/Source/timers.c
@@ -1,71 +1,29 @@
 /*
-    FreeRTOS V8.2.3 - Copyright (C) 2015 Real Time Engineers Ltd.
-    All rights reserved
-
-    VISIT http://www.FreeRTOS.org TO ENSURE YOU ARE USING THE LATEST VERSION.
-
-    This file is part of the FreeRTOS distribution.
-
-    FreeRTOS is free software; you can redistribute it and/or modify it under
-    the terms of the GNU General Public License (version 2) as published by the
-    Free Software Foundation >>>> AND MODIFIED BY <<<< the FreeRTOS exception.
-
-    ***************************************************************************
-    >>!   NOTE: The modification to the GPL is included to allow you to     !<<
-    >>!   distribute a combined work that includes FreeRTOS without being   !<<
-    >>!   obliged to provide the source code for proprietary components     !<<
-    >>!   outside of the FreeRTOS kernel.                                   !<<
-    ***************************************************************************
-
-    FreeRTOS is distributed in the hope that it will be useful, but WITHOUT ANY
-    WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
-    FOR A PARTICULAR PURPOSE.  Full license text is available on the following
-    link: http://www.freertos.org/a00114.html
-
-    ***************************************************************************
-     *                                                                       *
-     *    FreeRTOS provides completely free yet professionally developed,    *
-     *    robust, strictly quality controlled, supported, and cross          *
-     *    platform software that is more than just the market leader, it     *
-     *    is the industry's de facto standard.                               *
-     *                                                                       *
-     *    Help yourself get started quickly while simultaneously helping     *
-     *    to support the FreeRTOS project by purchasing a FreeRTOS           *
-     *    tutorial book, reference manual, or both:                          *
-     *    http://www.FreeRTOS.org/Documentation                              *
-     *                                                                       *
-    ***************************************************************************
-
-    http://www.FreeRTOS.org/FAQHelp.html - Having a problem?  Start by reading
-    the FAQ page "My application does not run, what could be wrong?".  Have you
-    defined configASSERT()?
-
-    http://www.FreeRTOS.org/support - In return for receiving this top quality
-    embedded software for free we request you assist our global community by
-    participating in the support forum.
-
-    http://www.FreeRTOS.org/training - Investing in training allows your team to
-    be as productive as possible as early as possible.  Now you can receive
-    FreeRTOS training directly from Richard Barry, CEO of Real Time Engineers
-    Ltd, and the world's leading authority on the world's leading RTOS.
-
-    http://www.FreeRTOS.org/plus - A selection of FreeRTOS ecosystem products,
-    including FreeRTOS+Trace - an indispensable productivity tool, a DOS
-    compatible FAT file system, and our tiny thread aware UDP/IP stack.
-
-    http://www.FreeRTOS.org/labs - Where new FreeRTOS products go to incubate.
-    Come and try FreeRTOS+TCP, our new open source TCP/IP stack for FreeRTOS.
-
-    http://www.OpenRTOS.com - Real Time Engineers ltd. license FreeRTOS to High
-    Integrity Systems ltd. to sell under the OpenRTOS brand.  Low cost OpenRTOS
-    licenses offer ticketed support, indemnification and commercial middleware.
-
-    http://www.SafeRTOS.com - High Integrity Systems also provide a safety
-    engineered and independently SIL3 certified version for use in safety and
-    mission critical applications that require provable dependability.
-
-    1 tab == 4 spaces!
-*/
+ * FreeRTOS Kernel V10.0.1
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
 
 /* Standard includes. */
 #include 
@@ -100,6 +58,12 @@ configUSE_TIMERS is set to 1 in FreeRTOSConfig.h. */
 /* Misc definitions. */
 #define tmrNO_DELAY		( TickType_t ) 0U
 
+/* The name assigned to the timer service task.  This can be overridden by
+defining trmTIMER_SERVICE_TASK_NAME in FreeRTOSConfig.h. */
+#ifndef configTIMER_SERVICE_TASK_NAME
+#define configTIMER_SERVICE_TASK_NAME "Tmr Svc"
+#endif
+
 /* The definition of the timers themselves. */
 typedef struct tmrTimerControl
 {
@@ -112,6 +76,10 @@ typedef struct tmrTimerControl
 #if( configUSE_TRACE_FACILITY == 1 )
     UBaseType_t			uxTimerNumber;		/*<< An ID assigned by trace tools such as FreeRTOS+Trace */
 #endif
+
+#if( ( configSUPPORT_STATIC_ALLOCATION == 1 ) && ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) )
+    uint8_t 			ucStaticallyAllocated; /*<< Set to pdTRUE if the timer was created statically so no attempt is made to free the memory again if the timer is later deleted. */
+#endif
 } xTIMER;
 
 /* The old xTIMER name is maintained above then typedefed to the new Timer_t
@@ -154,29 +122,34 @@ typedef struct tmrTimerQueueMessage
     } u;
 } DaemonTaskMessage_t;
 
-/*lint -e956 A manual analysis and inspection has been used to determine which
-static variables must be declared volatile. */
+/*lint -save -e956 A manual analysis and inspection has been used to determine
+which static variables must be declared volatile. */
 
 /* The list in which active timers are stored.  Timers are referenced in expire
 time order, with the nearest expiry time at the front of the list.  Only the
 timer service task is allowed to access these lists. */
-PRIVILEGED_DATA static List_t xActiveTimerList1;
-PRIVILEGED_DATA static List_t xActiveTimerList2;
-PRIVILEGED_DATA static List_t* pxCurrentTimerList;
-PRIVILEGED_DATA static List_t* pxOverflowTimerList;
+PRIVILEGED_DATA static List_t xActiveTimerList1 = {0};
+PRIVILEGED_DATA static List_t xActiveTimerList2 = {0};
+PRIVILEGED_DATA static List_t* pxCurrentTimerList = NULL;
+PRIVILEGED_DATA static List_t* pxOverflowTimerList = NULL;
 
 /* A queue that is used to send commands to the timer service task. */
 PRIVILEGED_DATA static QueueHandle_t xTimerQueue = NULL;
+PRIVILEGED_DATA static TaskHandle_t xTimerTaskHandle = NULL;
 
-#if ( INCLUDE_xTimerGetTimerDaemonTaskHandle == 1 )
+/*lint -restore */
 
-PRIVILEGED_DATA static TaskHandle_t xTimerTaskHandle = NULL;
+/*-----------------------------------------------------------*/
 
-#endif
+#if( configSUPPORT_STATIC_ALLOCATION == 1 )
 
-/*lint +e956 */
+/* If static allocation is supported then the application must provide the
+following callback function - which enables the application to optionally
+provide the memory that will be used by the timer task as the task's stack
+and TCB. */
+extern void vApplicationGetTimerTaskMemory( StaticTask_t** ppxTimerTaskTCBBuffer, StackType_t** ppxTimerTaskStackBuffer, uint32_t* pulTimerTaskStackSize );
 
-/*-----------------------------------------------------------*/
+#endif
 
 /*
  * Initialise the infrastructure used by the timer service task if it has not
@@ -235,11 +208,22 @@ static TickType_t prvGetNextExpireTime( BaseType_t* const pxListWasEmpty ) PRIVI
  */
 static void prvProcessTimerOrBlockTask( const TickType_t xNextExpireTime, BaseType_t xListWasEmpty ) PRIVILEGED_FUNCTION;
 
+/*
+ * Called after a Timer_t structure has been allocated either statically or
+ * dynamically to fill in the structure's members.
+ */
+static void prvInitialiseNewTimer(	const char* const pcTimerName,			/*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+                                    const TickType_t xTimerPeriodInTicks,
+                                    const UBaseType_t uxAutoReload,
+                                    void* const pvTimerID,
+                                    TimerCallbackFunction_t pxCallbackFunction,
+                                    Timer_t* pxNewTimer ) PRIVILEGED_FUNCTION;
 /*-----------------------------------------------------------*/
 
 BaseType_t xTimerCreateTimerTask( void )
 {
     BaseType_t xReturn = pdFAIL;
+
     /* This function is called when the scheduler is started if
     configUSE_TIMERS is set to 1.  Check that the infrastructure used by the
     timer service task has been created/initialised.  If timers have already
@@ -248,18 +232,36 @@ BaseType_t xTimerCreateTimerTask( void )
 
     if ( xTimerQueue != NULL )
     {
-#if ( INCLUDE_xTimerGetTimerDaemonTaskHandle == 1 )
+#if( configSUPPORT_STATIC_ALLOCATION == 1 )
         {
-            /* Create the timer task, storing its handle in xTimerTaskHandle so
-            it can be returned by the xTimerGetTimerDaemonTaskHandle() function. */
-            xReturn = xTaskCreate( prvTimerTask, "Tmr Svc", ( uint16_t ) configTIMER_TASK_STACK_DEPTH, NULL, ( ( UBaseType_t ) configTIMER_TASK_PRIORITY ) | portPRIVILEGE_BIT, &xTimerTaskHandle );
+            StaticTask_t* pxTimerTaskTCBBuffer = NULL;
+            StackType_t* pxTimerTaskStackBuffer = NULL;
+            uint32_t ulTimerTaskStackSize;
+
+            vApplicationGetTimerTaskMemory( &pxTimerTaskTCBBuffer, &pxTimerTaskStackBuffer, &ulTimerTaskStackSize );
+            xTimerTaskHandle = xTaskCreateStatic(	prvTimerTask,
+            configTIMER_SERVICE_TASK_NAME,
+            ulTimerTaskStackSize,
+            NULL,
+            ( ( UBaseType_t ) configTIMER_TASK_PRIORITY ) | portPRIVILEGE_BIT,
+            pxTimerTaskStackBuffer,
+            pxTimerTaskTCBBuffer );
+
+            if ( xTimerTaskHandle != NULL )
+            {
+                xReturn = pdPASS;
+            }
         }
 #else
         {
-            /* Create the timer task without storing its handle. */
-            xReturn = xTaskCreate( prvTimerTask, "Tmr Svc", ( uint16_t ) configTIMER_TASK_STACK_DEPTH, NULL, ( ( UBaseType_t ) configTIMER_TASK_PRIORITY ) | portPRIVILEGE_BIT, NULL);
+            xReturn = xTaskCreate(	prvTimerTask,
+            configTIMER_SERVICE_TASK_NAME,
+            configTIMER_TASK_STACK_DEPTH,
+            NULL,
+            ( ( UBaseType_t ) configTIMER_TASK_PRIORITY ) | portPRIVILEGE_BIT,
+            &xTimerTaskHandle );
         }
-#endif
+#endif /* configSUPPORT_STATIC_ALLOCATION */
     }
     else
     {
@@ -271,42 +273,108 @@ BaseType_t xTimerCreateTimerTask( void )
 }
 /*-----------------------------------------------------------*/
 
-TimerHandle_t xTimerCreate( const char* const pcTimerName, const TickType_t xTimerPeriodInTicks, const UBaseType_t uxAutoReload, void* const pvTimerID, TimerCallbackFunction_t pxCallbackFunction )   /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 )
+
+TimerHandle_t xTimerCreate(	const char* const pcTimerName,			/*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+                            const TickType_t xTimerPeriodInTicks,
+                            const UBaseType_t uxAutoReload,
+                            void* const pvTimerID,
+                            TimerCallbackFunction_t pxCallbackFunction )
 {
     Timer_t* pxNewTimer;
 
-    /* Allocate the timer structure. */
-    if ( xTimerPeriodInTicks == ( TickType_t ) 0U )
-    {
-        pxNewTimer = NULL;
-    }
-    else
+    pxNewTimer = ( Timer_t* ) pvPortMalloc( sizeof( Timer_t ) );
+
+    if ( pxNewTimer != NULL )
     {
-        pxNewTimer = ( Timer_t* ) pvPortMalloc( sizeof( Timer_t ) );
+        prvInitialiseNewTimer( pcTimerName, xTimerPeriodInTicks, uxAutoReload, pvTimerID, pxCallbackFunction, pxNewTimer );
 
-        if ( pxNewTimer != NULL )
+#if( configSUPPORT_STATIC_ALLOCATION == 1 )
         {
-            /* Ensure the infrastructure used by the timer service task has been
-            created/initialised. */
-            prvCheckForValidListAndQueue();
-            /* Initialise the timer structure members using the function parameters. */
-            pxNewTimer->pcTimerName = pcTimerName;
-            pxNewTimer->xTimerPeriodInTicks = xTimerPeriodInTicks;
-            pxNewTimer->uxAutoReload = uxAutoReload;
-            pxNewTimer->pvTimerID = pvTimerID;
-            pxNewTimer->pxCallbackFunction = pxCallbackFunction;
-            vListInitialiseItem( &( pxNewTimer->xTimerListItem ) );
-            traceTIMER_CREATE( pxNewTimer );
+            /* Timers can be created statically or dynamically, so note this
+            timer was created dynamically in case the timer is later
+            deleted. */
+            pxNewTimer->ucStaticallyAllocated = pdFALSE;
         }
-        else
+#endif /* configSUPPORT_STATIC_ALLOCATION */
+    }
+
+    return pxNewTimer;
+}
+
+#endif /* configSUPPORT_STATIC_ALLOCATION */
+/*-----------------------------------------------------------*/
+
+#if( configSUPPORT_STATIC_ALLOCATION == 1 )
+
+TimerHandle_t xTimerCreateStatic(	const char* const pcTimerName,		/*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+                                    const TickType_t xTimerPeriodInTicks,
+                                    const UBaseType_t uxAutoReload,
+                                    void* const pvTimerID,
+                                    TimerCallbackFunction_t pxCallbackFunction,
+                                    StaticTimer_t* pxTimerBuffer )
+{
+    Timer_t* pxNewTimer;
+
+#if( configASSERT_DEFINED == 1 )
+    {
+        /* Sanity check that the size of the structure used to declare a
+        variable of type StaticTimer_t equals the size of the real timer
+        structure. */
+        volatile size_t xSize = sizeof( StaticTimer_t );
+        configASSERT( xSize == sizeof( Timer_t ) );
+    }
+#endif /* configASSERT_DEFINED */
+
+    /* A pointer to a StaticTimer_t structure MUST be provided, use it. */
+    configASSERT( pxTimerBuffer );
+    pxNewTimer = ( Timer_t* ) pxTimerBuffer;  /*lint !e740 Unusual cast is ok as the structures are designed to have the same alignment, and the size is checked by an assert. */
+
+    if ( pxNewTimer != NULL )
+    {
+        prvInitialiseNewTimer( pcTimerName, xTimerPeriodInTicks, uxAutoReload, pvTimerID, pxCallbackFunction, pxNewTimer );
+
+#if( configSUPPORT_DYNAMIC_ALLOCATION == 1 )
         {
-            traceTIMER_CREATE_FAILED();
+            /* Timers can be created statically or dynamically so note this
+            timer was created statically in case it is later deleted. */
+            pxNewTimer->ucStaticallyAllocated = pdTRUE;
         }
+#endif /* configSUPPORT_DYNAMIC_ALLOCATION */
     }
 
+    return pxNewTimer;
+}
+
+#endif /* configSUPPORT_STATIC_ALLOCATION */
+/*-----------------------------------------------------------*/
+
+static void prvInitialiseNewTimer(	const char* const pcTimerName,			/*lint !e971 Unqualified char types are allowed for strings and single characters only. */
+                                    const TickType_t xTimerPeriodInTicks,
+                                    const UBaseType_t uxAutoReload,
+                                    void* const pvTimerID,
+                                    TimerCallbackFunction_t pxCallbackFunction,
+                                    Timer_t* pxNewTimer )
+{
     /* 0 is not a valid value for xTimerPeriodInTicks. */
     configASSERT( ( xTimerPeriodInTicks > 0 ) );
-    return ( TimerHandle_t ) pxNewTimer;
+
+    if ( pxNewTimer != NULL )
+    {
+        /* Ensure the infrastructure used by the timer service task has been
+        created/initialised. */
+        prvCheckForValidListAndQueue();
+
+        /* Initialise the timer structure members using the function
+        parameters. */
+        pxNewTimer->pcTimerName = pcTimerName;
+        pxNewTimer->xTimerPeriodInTicks = xTimerPeriodInTicks;
+        pxNewTimer->uxAutoReload = uxAutoReload;
+        pxNewTimer->pvTimerID = pvTimerID;
+        pxNewTimer->pxCallbackFunction = pxCallbackFunction;
+        vListInitialiseItem( &( pxNewTimer->xTimerListItem ) );
+        traceTIMER_CREATE( pxNewTimer );
+    }
 }
 /*-----------------------------------------------------------*/
 
@@ -314,6 +382,7 @@ BaseType_t xTimerGenericCommand( TimerHandle_t xTimer, const BaseType_t xCommand
 {
     BaseType_t xReturn = pdFAIL;
     DaemonTaskMessage_t xMessage;
+
     configASSERT( xTimer );
 
     /* Send a message to the timer service task to perform a particular action
@@ -352,8 +421,6 @@ BaseType_t xTimerGenericCommand( TimerHandle_t xTimer, const BaseType_t xCommand
 }
 /*-----------------------------------------------------------*/
 
-#if ( INCLUDE_xTimerGetTimerDaemonTaskHandle == 1 )
-
 TaskHandle_t xTimerGetTimerDaemonTaskHandle( void )
 {
     /* If xTimerGetTimerDaemonTaskHandle() is called before the scheduler has been
@@ -361,13 +428,32 @@ TaskHandle_t xTimerGetTimerDaemonTaskHandle( void )
     configASSERT( ( xTimerTaskHandle != NULL ) );
     return xTimerTaskHandle;
 }
+/*-----------------------------------------------------------*/
 
-#endif
+TickType_t xTimerGetPeriod( TimerHandle_t xTimer )
+{
+    Timer_t* pxTimer = ( Timer_t* ) xTimer;
+
+    configASSERT( xTimer );
+    return pxTimer->xTimerPeriodInTicks;
+}
+/*-----------------------------------------------------------*/
+
+TickType_t xTimerGetExpiryTime( TimerHandle_t xTimer )
+{
+    Timer_t* pxTimer = ( Timer_t* ) xTimer;
+    TickType_t xReturn;
+
+    configASSERT( xTimer );
+    xReturn = listGET_LIST_ITEM_VALUE( &( pxTimer->xTimerListItem ) );
+    return xReturn;
+}
 /*-----------------------------------------------------------*/
 
-const char* pcTimerGetTimerName( TimerHandle_t xTimer )
+const char* pcTimerGetName( TimerHandle_t xTimer )  /*lint !e971 Unqualified char types are allowed for strings and single characters only. */
 {
     Timer_t* pxTimer = ( Timer_t* ) xTimer;
+
     configASSERT( xTimer );
     return pxTimer->pcTimerName;
 }
@@ -377,6 +463,7 @@ static void prvProcessExpiredTimer( const TickType_t xNextExpireTime, const Tick
 {
     BaseType_t xResult;
     Timer_t* const pxTimer = ( Timer_t* ) listGET_OWNER_OF_HEAD_ENTRY( pxCurrentTimerList );
+
     /* Remove the timer from the list of active timers.  A check has already
     been performed to ensure the list is not empty. */
     ( void ) uxListRemove( &( pxTimer->xTimerListItem ) );
@@ -389,7 +476,7 @@ static void prvProcessExpiredTimer( const TickType_t xNextExpireTime, const Tick
         /* The timer is inserted into a list using a time relative to anything
         other than the current time.  It will therefore be inserted into the
         correct list relative to the time this task thinks it is now. */
-        if ( prvInsertTimerInActiveList( pxTimer, ( xNextExpireTime + pxTimer->xTimerPeriodInTicks ), xTimeNow, xNextExpireTime ) == pdTRUE )
+        if ( prvInsertTimerInActiveList( pxTimer, ( xNextExpireTime + pxTimer->xTimerPeriodInTicks ), xTimeNow, xNextExpireTime ) != pdFALSE )
         {
             /* The timer expired before it was added to the active timer
             list.  Reload it now.  */
@@ -416,17 +503,32 @@ static void prvTimerTask( void* pvParameters )
 {
     TickType_t xNextExpireTime;
     BaseType_t xListWasEmpty;
+
     /* Just to avoid compiler warnings. */
     ( void ) pvParameters;
 
+#if( configUSE_DAEMON_TASK_STARTUP_HOOK == 1 )
+    {
+        extern void vApplicationDaemonTaskStartupHook( void );
+
+        /* Allow the application writer to execute some code in the context of
+        this task at the point the task starts executing.  This is useful if the
+        application includes initialisation code that would benefit from
+        executing after the scheduler has been started. */
+        vApplicationDaemonTaskStartupHook();
+    }
+#endif /* configUSE_DAEMON_TASK_STARTUP_HOOK */
+
     for ( ;; )
     {
         /* Query the timers list to see if it contains any timers, and if so,
         obtain the time at which the next timer will expire. */
         xNextExpireTime = prvGetNextExpireTime( &xListWasEmpty );
+
         /* If a timer has expired, process it.  Otherwise, block this task
         until either a timer does expire, or a command is received. */
         prvProcessTimerOrBlockTask( xNextExpireTime, xListWasEmpty );
+
         /* Empty the command queue. */
         prvProcessReceivedCommands();
     }
@@ -437,6 +539,7 @@ static void prvProcessTimerOrBlockTask( const TickType_t xNextExpireTime, BaseTy
 {
     TickType_t xTimeNow;
     BaseType_t xTimerListsWereSwitched;
+
     vTaskSuspendAll();
     {
         /* Obtain the time now to make an assessment as to whether the timer
@@ -496,6 +599,7 @@ static void prvProcessTimerOrBlockTask( const TickType_t xNextExpireTime, BaseTy
 static TickType_t prvGetNextExpireTime( BaseType_t* const pxListWasEmpty )
 {
     TickType_t xNextExpireTime;
+
     /* Timers are listed in expiry time order, with the head of the list
     referencing the task that will expire first.  Obtain the time at which
     the timer with the nearest expiry time will expire.  If there are no
@@ -523,6 +627,7 @@ static TickType_t prvSampleTimeNow( BaseType_t* const pxTimerListsWereSwitched )
 {
     TickType_t xTimeNow;
     PRIVILEGED_DATA static TickType_t xLastTime = ( TickType_t ) 0U; /*lint !e956 Variable is only accessible to one task. */
+
     xTimeNow = xTaskGetTickCount();
 
     if ( xTimeNow < xLastTime )
@@ -536,6 +641,7 @@ static TickType_t prvSampleTimeNow( BaseType_t* const pxTimerListsWereSwitched )
     }
 
     xLastTime = xTimeNow;
+
     return xTimeNow;
 }
 /*-----------------------------------------------------------*/
@@ -543,6 +649,7 @@ static TickType_t prvSampleTimeNow( BaseType_t* const pxTimerListsWereSwitched )
 static BaseType_t prvInsertTimerInActiveList( Timer_t* const pxTimer, const TickType_t xNextExpiryTime, const TickType_t xTimeNow, const TickType_t xCommandTime )
 {
     BaseType_t xProcessTimerNow = pdFALSE;
+
     listSET_LIST_ITEM_VALUE( &( pxTimer->xTimerListItem ), xNextExpiryTime );
     listSET_LIST_ITEM_OWNER( &( pxTimer->xTimerListItem ), pxTimer );
 
@@ -550,7 +657,7 @@ static BaseType_t prvInsertTimerInActiveList( Timer_t* const pxTimer, const Tick
     {
         /* Has the expiry time elapsed between the command to start/reset a
         timer was issued, and the time the command was processed? */
-        if ( ( xTimeNow - xCommandTime ) >= pxTimer->xTimerPeriodInTicks )
+        if ( ( ( TickType_t ) ( xTimeNow - xCommandTime ) ) >= pxTimer->xTimerPeriodInTicks ) /*lint !e961 MISRA exception as the casts are only redundant for some ports. */
         {
             /* The time between a command being issued and the command being
             processed actually exceeds the timers period.  */
@@ -596,9 +703,11 @@ static void	prvProcessReceivedCommands( void )
             if ( xMessage.xMessageID < ( BaseType_t ) 0 )
             {
                 const CallbackParameters_t* const pxCallback = &( xMessage.u.xCallbackParameters );
+
                 /* The timer uses the xCallbackParameters member to request a
                 callback be executed.  Check the callback is not NULL. */
                 configASSERT( pxCallback );
+
                 /* Call the function. */
                 pxCallback->pxCallbackFunction( pxCallback->pvParameter1, pxCallback->ulParameter2 );
             }
@@ -617,7 +726,7 @@ static void	prvProcessReceivedCommands( void )
             software timer. */
             pxTimer = xMessage.u.xTimerParameters.pxTimer;
 
-            if ( listIS_CONTAINED_WITHIN( NULL, &( pxTimer->xTimerListItem ) ) == pdFALSE )
+            if ( listIS_CONTAINED_WITHIN( NULL, &( pxTimer->xTimerListItem ) ) == pdFALSE ) /*lint !e961. The cast is only redundant when NULL is passed into the macro. */
             {
                 /* The timer is in a list, remove it. */
                 ( void ) uxListRemove( &( pxTimer->xTimerListItem ) );
@@ -628,6 +737,7 @@ static void	prvProcessReceivedCommands( void )
             }
 
             traceTIMER_COMMAND_RECEIVED( pxTimer, xMessage.xMessageID, xMessage.u.xTimerParameters.xMessageValue );
+
             /* In this case the xTimerListsWereSwitched parameter is not used, but
             it must be present in the function call.  prvSampleTimeNow() must be
             called after the message is received from xTimerQueue so there is no
@@ -645,7 +755,7 @@ static void	prvProcessReceivedCommands( void )
                 case tmrCOMMAND_START_DONT_TRACE :
 
                     /* Start or restart a timer. */
-                    if ( prvInsertTimerInActiveList( pxTimer,  xMessage.u.xTimerParameters.xMessageValue + pxTimer->xTimerPeriodInTicks, xTimeNow, xMessage.u.xTimerParameters.xMessageValue ) == pdTRUE )
+                    if ( prvInsertTimerInActiveList( pxTimer,  xMessage.u.xTimerParameters.xMessageValue + pxTimer->xTimerPeriodInTicks, xTimeNow, xMessage.u.xTimerParameters.xMessageValue ) != pdFALSE )
                     {
                         /* The timer expired before it was added to the active
                         timer list.  Process it now. */
@@ -680,20 +790,43 @@ static void	prvProcessReceivedCommands( void )
                 case tmrCOMMAND_CHANGE_PERIOD_FROM_ISR :
                     pxTimer->xTimerPeriodInTicks = xMessage.u.xTimerParameters.xMessageValue;
                     configASSERT( ( pxTimer->xTimerPeriodInTicks > 0 ) );
-                    /* The new period does not really have a reference, and can be
-                    longer or shorter than the old one.  The command time is
-                    therefore set to the current time, and as the period cannot be
-                    zero the next expiry time can only be in the future, meaning
-                    (unlike for the xTimerStart() case above) there is no fail case
-                    that needs to be handled here. */
+
+                    /* The new period does not really have a reference, and can
+                    be longer or shorter than the old one.  The command time is
+                    therefore set to the current time, and as the period cannot
+                    be zero the next expiry time can only be in the future,
+                    meaning (unlike for the xTimerStart() case above) there is
+                    no fail case that needs to be handled here. */
                     ( void ) prvInsertTimerInActiveList( pxTimer, ( xTimeNow + pxTimer->xTimerPeriodInTicks ), xTimeNow, xTimeNow );
                     break;
 
                 case tmrCOMMAND_DELETE :
                     /* The timer has already been removed from the active list,
-                    just free up the memory. */
+                    just free up the memory if the memory was dynamically
+                    allocated. */
+#if( ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) && ( configSUPPORT_STATIC_ALLOCATION == 0 ) )
+                {
+                    /* The timer can only have been allocated dynamically -
+                    free it again. */
                     vPortFree( pxTimer );
-                    break;
+                }
+
+#elif( ( configSUPPORT_DYNAMIC_ALLOCATION == 1 ) && ( configSUPPORT_STATIC_ALLOCATION == 1 ) )
+                {
+                    /* The timer could have been allocated statically or
+                    dynamically, so check before attempting to free the
+                    memory. */
+                    if ( pxTimer->ucStaticallyAllocated == ( uint8_t ) pdFALSE )
+                    {
+                        vPortFree( pxTimer );
+                    }
+                    else
+                    {
+                        mtCOVERAGE_TEST_MARKER();
+                    }
+                }
+#endif /* configSUPPORT_DYNAMIC_ALLOCATION */
+                break;
 
                 default	:
                     /* Don't expect to get here. */
@@ -718,10 +851,12 @@ static void prvSwitchTimerLists( void )
     while ( listLIST_IS_EMPTY( pxCurrentTimerList ) == pdFALSE )
     {
         xNextExpireTime = listGET_ITEM_VALUE_OF_HEAD_ENTRY( pxCurrentTimerList );
+
         /* Remove the timer from the list. */
         pxTimer = ( Timer_t* ) listGET_OWNER_OF_HEAD_ENTRY( pxCurrentTimerList );
         ( void ) uxListRemove( &( pxTimer->xTimerListItem ) );
         traceTIMER_EXPIRED( pxTimer );
+
         /* Execute its callback, then send a command to restart the timer if
         it is an auto-reload timer.  It cannot be restarted here as the lists
         have not yet been switched. */
@@ -775,8 +910,22 @@ static void prvCheckForValidListAndQueue( void )
             vListInitialise( &xActiveTimerList2 );
             pxCurrentTimerList = &xActiveTimerList1;
             pxOverflowTimerList = &xActiveTimerList2;
-            xTimerQueue = xQueueCreate( ( UBaseType_t ) configTIMER_QUEUE_LENGTH, sizeof( DaemonTaskMessage_t ) );
-            configASSERT( xTimerQueue );
+
+#if( configSUPPORT_STATIC_ALLOCATION == 1 )
+            {
+                /* The timer queue is allocated statically in case
+                configSUPPORT_DYNAMIC_ALLOCATION is 0. */
+                static StaticQueue_t xStaticTimerQueue; /*lint !e956 Ok to declare in this manner to prevent additional conditional compilation guards in other locations. */
+                static uint8_t ucStaticTimerQueueStorage[ ( size_t ) configTIMER_QUEUE_LENGTH * sizeof( DaemonTaskMessage_t ) ]; /*lint !e956 Ok to declare in this manner to prevent additional conditional compilation guards in other locations. */
+
+                xTimerQueue = xQueueCreateStatic( ( UBaseType_t ) configTIMER_QUEUE_LENGTH, ( UBaseType_t ) sizeof( DaemonTaskMessage_t ), &( ucStaticTimerQueueStorage[ 0 ] ), &xStaticTimerQueue );
+            }
+#else
+            {
+                xTimerQueue = xQueueCreate( ( UBaseType_t ) configTIMER_QUEUE_LENGTH, sizeof( DaemonTaskMessage_t ) );
+            }
+#endif
+
 #if ( configQUEUE_REGISTRY_SIZE > 0 )
             {
                 if ( xTimerQueue != NULL )
@@ -803,16 +952,19 @@ BaseType_t xTimerIsTimerActive( TimerHandle_t xTimer )
 {
     BaseType_t xTimerIsInActiveList;
     Timer_t* pxTimer = ( Timer_t* ) xTimer;
+
     configASSERT( xTimer );
+
     /* Is the timer in the list of active timers? */
     taskENTER_CRITICAL();
     {
         /* Checking to see if it is in the NULL list in effect checks to see if
         it is referenced from either the current or the overflow timer lists in
         one go, but the logic has to be reversed, hence the '!'. */
-        xTimerIsInActiveList = ( BaseType_t ) !( listIS_CONTAINED_WITHIN( NULL, &( pxTimer->xTimerListItem ) ) );
+        xTimerIsInActiveList = ( BaseType_t ) !( listIS_CONTAINED_WITHIN( NULL, &( pxTimer->xTimerListItem ) ) ); /*lint !e961. Cast is only redundant when NULL is passed into the macro. */
     }
     taskEXIT_CRITICAL();
+
     return xTimerIsInActiveList;
 } /*lint !e818 Can't be pointer to const due to the typedef. */
 /*-----------------------------------------------------------*/
@@ -821,12 +973,15 @@ void* pvTimerGetTimerID( const TimerHandle_t xTimer )
 {
     Timer_t* const pxTimer = ( Timer_t* ) xTimer;
     void* pvReturn;
+
     configASSERT( xTimer );
+
     taskENTER_CRITICAL();
     {
         pvReturn = pxTimer->pvTimerID;
     }
     taskEXIT_CRITICAL();
+
     return pvReturn;
 }
 /*-----------------------------------------------------------*/
@@ -834,7 +989,9 @@ void* pvTimerGetTimerID( const TimerHandle_t xTimer )
 void vTimerSetTimerID( TimerHandle_t xTimer, void* pvNewID )
 {
     Timer_t* const pxTimer = ( Timer_t* ) xTimer;
+
     configASSERT( xTimer );
+
     taskENTER_CRITICAL();
     {
         pxTimer->pvTimerID = pvNewID;
@@ -849,14 +1006,18 @@ BaseType_t xTimerPendFunctionCallFromISR( PendedFunction_t xFunctionToPend, void
 {
     DaemonTaskMessage_t xMessage;
     BaseType_t xReturn;
+
     /* Complete the message with the function parameters and post it to the
     daemon task. */
     xMessage.xMessageID = tmrCOMMAND_EXECUTE_CALLBACK_FROM_ISR;
     xMessage.u.xCallbackParameters.pxCallbackFunction = xFunctionToPend;
     xMessage.u.xCallbackParameters.pvParameter1 = pvParameter1;
     xMessage.u.xCallbackParameters.ulParameter2 = ulParameter2;
+
     xReturn = xQueueSendFromISR( xTimerQueue, &xMessage, pxHigherPriorityTaskWoken );
+
     tracePEND_FUNC_CALL_FROM_ISR( xFunctionToPend, pvParameter1, ulParameter2, xReturn );
+
     return xReturn;
 }
 
@@ -869,24 +1030,49 @@ BaseType_t xTimerPendFunctionCall( PendedFunction_t xFunctionToPend, void* pvPar
 {
     DaemonTaskMessage_t xMessage;
     BaseType_t xReturn;
+
     /* This function can only be called after a timer has been created or
     after the scheduler has been started because, until then, the timer
     queue does not exist. */
     configASSERT( xTimerQueue );
+
     /* Complete the message with the function parameters and post it to the
     daemon task. */
     xMessage.xMessageID = tmrCOMMAND_EXECUTE_CALLBACK;
     xMessage.u.xCallbackParameters.pxCallbackFunction = xFunctionToPend;
     xMessage.u.xCallbackParameters.pvParameter1 = pvParameter1;
     xMessage.u.xCallbackParameters.ulParameter2 = ulParameter2;
+
     xReturn = xQueueSendToBack( xTimerQueue, &xMessage, xTicksToWait );
+
     tracePEND_FUNC_CALL( xFunctionToPend, pvParameter1, ulParameter2, xReturn );
+
     return xReturn;
 }
 
 #endif /* INCLUDE_xTimerPendFunctionCall */
 /*-----------------------------------------------------------*/
 
+#if ( configUSE_TRACE_FACILITY == 1 )
+
+UBaseType_t uxTimerGetTimerNumber( TimerHandle_t xTimer )
+{
+    return ( ( Timer_t* ) xTimer )->uxTimerNumber;
+}
+
+#endif /* configUSE_TRACE_FACILITY */
+/*-----------------------------------------------------------*/
+
+#if ( configUSE_TRACE_FACILITY == 1 )
+
+void vTimerSetTimerNumber( TimerHandle_t xTimer, UBaseType_t uxTimerNumber )
+{
+    ( ( Timer_t* ) xTimer )->uxTimerNumber = uxTimerNumber;
+}
+
+#endif /* configUSE_TRACE_FACILITY */
+/*-----------------------------------------------------------*/
+
 /* This entire source file will be skipped if the application is not configured
 to include software timer functionality.  If you want to include software timer
 functionality then ensure configUSE_TIMERS is set to 1 in FreeRTOSConfig.h. */
diff --git a/EpsilonLights/STM32F407VGTx_FLASH.ld b/EpsilonLights/STM32F103C4Tx_FLASH.ld
similarity index 86%
rename from EpsilonLights/STM32F407VGTx_FLASH.ld
rename to EpsilonLights/STM32F103C4Tx_FLASH.ld
index 16a93c7d..3b00ece2 100644
--- a/EpsilonLights/STM32F407VGTx_FLASH.ld
+++ b/EpsilonLights/STM32F103C4Tx_FLASH.ld
@@ -1,208 +1,189 @@
-/*
-*****************************************************************************
-**
-
-**  File        : LinkerScript.ld
-**
-**  Abstract    : Linker script for STM32F407VGTx Device with
-**                1024KByte FLASH, 128KByte RAM
-**
-**                Set heap size, stack size and stack location according
-**                to application requirements.
-**
-**                Set memory bank area and size if external memory is used.
-**
-**  Target      : STMicroelectronics STM32
-**
-**
-**  Distribution: The file is distributed as is, without any warranty
-**                of any kind.
-**
-*****************************************************************************
-** @attention
-**
-** 
© COPYRIGHT(c) 2014 Ac6

-**
-** Redistribution and use in source and binary forms, with or without modification,
-** are permitted provided that the following conditions are met:
-**   1. Redistributions of source code must retain the above copyright notice,
-**      this list of conditions and the following disclaimer.
-**   2. Redistributions in binary form must reproduce the above copyright notice,
-**      this list of conditions and the following disclaimer in the documentation
-**      and/or other materials provided with the distribution.
-**   3. Neither the name of Ac6 nor the names of its contributors
-**      may be used to endorse or promote products derived from this software
-**      without specific prior written permission.
-**
-** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
-** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
-** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
-** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
-** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
-** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-**
-*****************************************************************************
-*/
-
-/* Entry Point */
-ENTRY(Reset_Handler)
-
-/* Highest address of the user mode stack */
-_estack = 0x20020000;    /* end of RAM */
-/* Generate a link error if heap and stack don't fit into RAM */
-_Min_Heap_Size = 0x200;      /* required amount of heap  */
-_Min_Stack_Size = 0x400; /* required amount of stack */
-
-/* Specify the memory areas */
-MEMORY
-{
-FLASH (rx)      : ORIGIN = 0x8000000, LENGTH = 1024K
-RAM (xrw)      : ORIGIN = 0x20000000, LENGTH = 128K
-CCMRAM (rw)      : ORIGIN = 0x10000000, LENGTH = 64K
-}
-
-/* Define output sections */
-SECTIONS
-{
-  /* The startup code goes first into FLASH */
-  .isr_vector :
-  {
-    . = ALIGN(4);
-    KEEP(*(.isr_vector)) /* Startup code */
-    . = ALIGN(4);
-  } >FLASH
-
-  /* The program code and other data goes into FLASH */
-  .text :
-  {
-    . = ALIGN(4);
-    *(.text)           /* .text sections (code) */
-    *(.text*)          /* .text* sections (code) */
-    *(.glue_7)         /* glue arm to thumb code */
-    *(.glue_7t)        /* glue thumb to arm code */
-    *(.eh_frame)
-
-    KEEP (*(.init))
-    KEEP (*(.fini))
-
-    . = ALIGN(4);
-    _etext = .;        /* define a global symbols at end of code */
-  } >FLASH
-
-  /* Constant data goes into FLASH */
-  .rodata :
-  {
-    . = ALIGN(4);
-    *(.rodata)         /* .rodata sections (constants, strings, etc.) */
-    *(.rodata*)        /* .rodata* sections (constants, strings, etc.) */
-    . = ALIGN(4);
-  } >FLASH
-
-  .ARM.extab   : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
-  .ARM : {
-    __exidx_start = .;
-    *(.ARM.exidx*)
-    __exidx_end = .;
-  } >FLASH
-
-  .preinit_array     :
-  {
-    PROVIDE_HIDDEN (__preinit_array_start = .);
-    KEEP (*(.preinit_array*))
-    PROVIDE_HIDDEN (__preinit_array_end = .);
-  } >FLASH
-  .init_array :
-  {
-    PROVIDE_HIDDEN (__init_array_start = .);
-    KEEP (*(SORT(.init_array.*)))
-    KEEP (*(.init_array*))
-    PROVIDE_HIDDEN (__init_array_end = .);
-  } >FLASH
-  .fini_array :
-  {
-    PROVIDE_HIDDEN (__fini_array_start = .);
-    KEEP (*(SORT(.fini_array.*)))
-    KEEP (*(.fini_array*))
-    PROVIDE_HIDDEN (__fini_array_end = .);
-  } >FLASH
-
-  /* used by the startup to initialize data */
-  _sidata = LOADADDR(.data);
-
-  /* Initialized data sections goes into RAM, load LMA copy after code */
-  .data : 
-  {
-    . = ALIGN(4);
-    _sdata = .;        /* create a global symbol at data start */
-    *(.data)           /* .data sections */
-    *(.data*)          /* .data* sections */
-
-    . = ALIGN(4);
-    _edata = .;        /* define a global symbol at data end */
-  } >RAM AT> FLASH
-
-  _siccmram = LOADADDR(.ccmram);
-
-  /* CCM-RAM section 
-  * 
-  * IMPORTANT NOTE! 
-  * If initialized variables will be placed in this section,
-  * the startup code needs to be modified to copy the init-values.  
-  */
-  .ccmram :
-  {
-    . = ALIGN(4);
-    _sccmram = .;       /* create a global symbol at ccmram start */
-    *(.ccmram)
-    *(.ccmram*)
-    
-    . = ALIGN(4);
-    _eccmram = .;       /* create a global symbol at ccmram end */
-  } >CCMRAM AT> FLASH
-
-  
-  /* Uninitialized data section */
-  . = ALIGN(4);
-  .bss :
-  {
-    /* This is used by the startup in order to initialize the .bss secion */
-    _sbss = .;         /* define a global symbol at bss start */
-    __bss_start__ = _sbss;
-    *(.bss)
-    *(.bss*)
-    *(COMMON)
-
-    . = ALIGN(4);
-    _ebss = .;         /* define a global symbol at bss end */
-    __bss_end__ = _ebss;
-  } >RAM
-
-  /* User_heap_stack section, used to check that there is enough RAM left */
-  ._user_heap_stack :
-  {
-    . = ALIGN(8);
-    PROVIDE ( end = . );
-    PROVIDE ( _end = . );
-    . = . + _Min_Heap_Size;
-    . = . + _Min_Stack_Size;
-    . = ALIGN(8);
-  } >RAM
-
-  
-
-  /* Remove information from the standard libraries */
-  /DISCARD/ :
-  {
-    libc.a ( * )
-    libm.a ( * )
-    libgcc.a ( * )
-  }
-
-  .ARM.attributes 0 : { *(.ARM.attributes) }
-}
-
-
+/*
+******************************************************************************
+**
+
+**  File        : LinkerScript.ld
+**
+**  Author		: Auto-generated by Ac6 System Workbench
+**
+**  Abstract    : Linker script for STM32F103C4Tx series
+**                16Kbytes FLASH and 6Kbytes RAM
+**
+**                Set heap size, stack size and stack location according
+**                to application requirements.
+**
+**                Set memory bank area and size if external memory is used.
+**
+**  Target      : STMicroelectronics STM32
+**
+**  Distribution: The file is distributed “as is,” without any warranty
+**                of any kind.
+**
+*****************************************************************************
+** @attention
+**
+** 
© COPYRIGHT(c) 2014 Ac6

+**
+** Redistribution and use in source and binary forms, with or without modification,
+** are permitted provided that the following conditions are met:
+**   1. Redistributions of source code must retain the above copyright notice,
+**      this list of conditions and the following disclaimer.
+**   2. Redistributions in binary form must reproduce the above copyright notice,
+**      this list of conditions and the following disclaimer in the documentation
+**      and/or other materials provided with the distribution.
+**   3. Neither the name of Ac6 nor the names of its contributors
+**      may be used to endorse or promote products derived from this software
+**      without specific prior written permission.
+**
+** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20001800;    /* end of RAM */
+/* Generate a link error if heap and stack don't fit into RAM */
+_Min_Heap_Size = 0x200;      /* required amount of heap  */
+_Min_Stack_Size = 0x400; /* required amount of stack */
+
+/* Specify the memory areas */
+MEMORY
+{
+RAM (xrw)      : ORIGIN = 0x20000000, LENGTH = 6K
+FLASH (rx)      : ORIGIN = 0x8000000, LENGTH = 16K
+}
+
+/* Define output sections */
+SECTIONS
+{
+  /* The startup code goes first into FLASH */
+  .isr_vector :
+  {
+    . = ALIGN(4);
+    KEEP(*(.isr_vector)) /* Startup code */
+    . = ALIGN(4);
+  } >FLASH
+
+  /* The program code and other data goes into FLASH */
+  .text :
+  {
+    . = ALIGN(4);
+    *(.text)           /* .text sections (code) */
+    *(.text*)          /* .text* sections (code) */
+    *(.glue_7)         /* glue arm to thumb code */
+    *(.glue_7t)        /* glue thumb to arm code */
+    *(.eh_frame)
+
+    KEEP (*(.init))
+    KEEP (*(.fini))
+
+    . = ALIGN(4);
+    _etext = .;        /* define a global symbols at end of code */
+  } >FLASH
+
+  /* Constant data goes into FLASH */
+  .rodata :
+  {
+    . = ALIGN(4);
+    *(.rodata)         /* .rodata sections (constants, strings, etc.) */
+    *(.rodata*)        /* .rodata* sections (constants, strings, etc.) */
+    . = ALIGN(4);
+  } >FLASH
+
+  .ARM.extab   : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
+  .ARM : {
+    __exidx_start = .;
+    *(.ARM.exidx*)
+    __exidx_end = .;
+  } >FLASH
+
+  .preinit_array     :
+  {
+    PROVIDE_HIDDEN (__preinit_array_start = .);
+    KEEP (*(.preinit_array*))
+    PROVIDE_HIDDEN (__preinit_array_end = .);
+  } >FLASH
+  .init_array :
+  {
+    PROVIDE_HIDDEN (__init_array_start = .);
+    KEEP (*(SORT(.init_array.*)))
+    KEEP (*(.init_array*))
+    PROVIDE_HIDDEN (__init_array_end = .);
+  } >FLASH
+  .fini_array :
+  {
+    PROVIDE_HIDDEN (__fini_array_start = .);
+    KEEP (*(SORT(.fini_array.*)))
+    KEEP (*(.fini_array*))
+    PROVIDE_HIDDEN (__fini_array_end = .);
+  } >FLASH
+
+  /* used by the startup to initialize data */
+  _sidata = LOADADDR(.data);
+
+  /* Initialized data sections goes into RAM, load LMA copy after code */
+  .data : 
+  {
+    . = ALIGN(4);
+    _sdata = .;        /* create a global symbol at data start */
+    *(.data)           /* .data sections */
+    *(.data*)          /* .data* sections */
+
+    . = ALIGN(4);
+    _edata = .;        /* define a global symbol at data end */
+  } >RAM AT> FLASH
+
+  
+  /* Uninitialized data section */
+  . = ALIGN(4);
+  .bss :
+  {
+    /* This is used by the startup in order to initialize the .bss secion */
+    _sbss = .;         /* define a global symbol at bss start */
+    __bss_start__ = _sbss;
+    *(.bss)
+    *(.bss*)
+    *(COMMON)
+
+    . = ALIGN(4);
+    _ebss = .;         /* define a global symbol at bss end */
+    __bss_end__ = _ebss;
+  } >RAM
+
+  /* User_heap_stack section, used to check that there is enough RAM left */
+  ._user_heap_stack :
+  {
+    . = ALIGN(8);
+    PROVIDE ( end = . );
+    PROVIDE ( _end = . );
+    . = . + _Min_Heap_Size;
+    . = . + _Min_Stack_Size;
+    . = ALIGN(8);
+  } >RAM
+
+  
+
+  /* Remove information from the standard libraries */
+  /DISCARD/ :
+  {
+    libc.a ( * )
+    libm.a ( * )
+    libgcc.a ( * )
+  }
+
+  .ARM.attributes 0 : { *(.ARM.attributes) }
+}
+
+
diff --git a/EpsilonLights/Src/freertos.c b/EpsilonLights/Src/freertos.c
deleted file mode 100644
index 5c7b946a..00000000
--- a/EpsilonLights/Src/freertos.c
+++ /dev/null
@@ -1,60 +0,0 @@
-/**
-  ******************************************************************************
-  * File Name          : freertos.c
-  * Description        : Code for freertos applications
-  ******************************************************************************
-  *
-  * COPYRIGHT(c) 2016 STMicroelectronics
-  *
-  * Redistribution and use in source and binary forms, with or without modification,
-  * are permitted provided that the following conditions are met:
-  *   1. Redistributions of source code must retain the above copyright notice,
-  *      this list of conditions and the following disclaimer.
-  *   2. Redistributions in binary form must reproduce the above copyright notice,
-  *      this list of conditions and the following disclaimer in the documentation
-  *      and/or other materials provided with the distribution.
-  *   3. Neither the name of STMicroelectronics nor the names of its contributors
-  *      may be used to endorse or promote products derived from this software
-  *      without specific prior written permission.
-  *
-  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
-  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
-  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
-  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
-  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
-  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-  *
-  ******************************************************************************
-  */
-
-/* Includes ------------------------------------------------------------------*/
-#include "FreeRTOS.h"
-#include "task.h"
-
-/* USER CODE BEGIN Includes */
-
-/* USER CODE END Includes */
-
-/* Variables -----------------------------------------------------------------*/
-
-/* USER CODE BEGIN Variables */
-
-/* USER CODE END Variables */
-
-/* Function prototypes -------------------------------------------------------*/
-
-/* USER CODE BEGIN FunctionPrototypes */
-
-/* USER CODE END FunctionPrototypes */
-
-/* Hook prototypes */
-
-/* USER CODE BEGIN Application */
-
-/* USER CODE END Application */
-
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/EpsilonLights/Src/stm32f4xx_hal_msp.c b/EpsilonLights/Src/stm32f4xx_hal_msp.c
deleted file mode 100644
index 470c4da2..00000000
--- a/EpsilonLights/Src/stm32f4xx_hal_msp.c
+++ /dev/null
@@ -1,135 +0,0 @@
-/**
-  ******************************************************************************
-  * File Name          : stm32f4xx_hal_msp.c
-  * Description        : This file provides code for the MSP Initialization
-  *                      and de-Initialization codes.
-  ******************************************************************************
-  *
-  * COPYRIGHT(c) 2016 STMicroelectronics
-  *
-  * Redistribution and use in source and binary forms, with or without modification,
-  * are permitted provided that the following conditions are met:
-  *   1. Redistributions of source code must retain the above copyright notice,
-  *      this list of conditions and the following disclaimer.
-  *   2. Redistributions in binary form must reproduce the above copyright notice,
-  *      this list of conditions and the following disclaimer in the documentation
-  *      and/or other materials provided with the distribution.
-  *   3. Neither the name of STMicroelectronics nor the names of its contributors
-  *      may be used to endorse or promote products derived from this software
-  *      without specific prior written permission.
-  *
-  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
-  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
-  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
-  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
-  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
-  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-  *
-  ******************************************************************************
-  */
-/* Includes ------------------------------------------------------------------*/
-#include "stm32f4xx_hal.h"
-
-extern void Error_Handler(void);
-/* USER CODE BEGIN 0 */
-
-/* USER CODE END 0 */
-
-/**
-  * Initializes the Global MSP.
-  */
-void HAL_MspInit(void)
-{
-    /* USER CODE BEGIN MspInit 0 */
-    /* USER CODE END MspInit 0 */
-    HAL_NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_4);
-    /* System interrupt init*/
-    /* MemoryManagement_IRQn interrupt configuration */
-    HAL_NVIC_SetPriority(MemoryManagement_IRQn, 0, 0);
-    /* BusFault_IRQn interrupt configuration */
-    HAL_NVIC_SetPriority(BusFault_IRQn, 0, 0);
-    /* UsageFault_IRQn interrupt configuration */
-    HAL_NVIC_SetPriority(UsageFault_IRQn, 0, 0);
-    /* SVCall_IRQn interrupt configuration */
-    HAL_NVIC_SetPriority(SVCall_IRQn, 0, 0);
-    /* DebugMonitor_IRQn interrupt configuration */
-    HAL_NVIC_SetPriority(DebugMonitor_IRQn, 0, 0);
-    /* PendSV_IRQn interrupt configuration */
-    HAL_NVIC_SetPriority(PendSV_IRQn, 15, 0);
-    /* SysTick_IRQn interrupt configuration */
-    HAL_NVIC_SetPriority(SysTick_IRQn, 15, 0);
-    /* USER CODE BEGIN MspInit 1 */
-    /* USER CODE END MspInit 1 */
-}
-
-void HAL_CAN_MspInit(CAN_HandleTypeDef* hcan)
-{
-    GPIO_InitTypeDef GPIO_InitStruct;
-
-    if (hcan->Instance == CAN2)
-    {
-        /* USER CODE BEGIN CAN2_MspInit 0 */
-        /* USER CODE END CAN2_MspInit 0 */
-        /* Peripheral clock enable */
-        __HAL_RCC_CAN2_CLK_ENABLE();
-        __HAL_RCC_CAN1_CLK_ENABLE();
-        /**CAN2 GPIO Configuration
-        PB12     ------> CAN2_RX
-        PB13     ------> CAN2_TX
-        */
-        GPIO_InitStruct.Pin = GPIO_PIN_12 | GPIO_PIN_13;
-        GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
-        GPIO_InitStruct.Pull = GPIO_NOPULL;
-        GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
-        GPIO_InitStruct.Alternate = GPIO_AF9_CAN2;
-        HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
-        /* Peripheral interrupt init */
-        HAL_NVIC_SetPriority(CAN2_TX_IRQn, 0, 0);
-        HAL_NVIC_EnableIRQ(CAN2_TX_IRQn);
-        HAL_NVIC_SetPriority(CAN2_RX0_IRQn, 0, 0);
-        HAL_NVIC_EnableIRQ(CAN2_RX0_IRQn);
-        /* USER CODE BEGIN CAN2_MspInit 1 */
-        /* USER CODE END CAN2_MspInit 1 */
-    }
-}
-
-void HAL_CAN_MspDeInit(CAN_HandleTypeDef* hcan)
-{
-    if (hcan->Instance == CAN2)
-    {
-        /* USER CODE BEGIN CAN2_MspDeInit 0 */
-        /* USER CODE END CAN2_MspDeInit 0 */
-        /* Peripheral clock disable */
-        __HAL_RCC_CAN2_CLK_DISABLE();
-        __HAL_RCC_CAN1_CLK_DISABLE();
-        /**CAN2 GPIO Configuration
-        PB12     ------> CAN2_RX
-        PB13     ------> CAN2_TX
-        */
-        HAL_GPIO_DeInit(GPIOB, GPIO_PIN_12 | GPIO_PIN_13);
-        /* Peripheral interrupt DeInit*/
-        HAL_NVIC_DisableIRQ(CAN2_TX_IRQn);
-        HAL_NVIC_DisableIRQ(CAN2_RX0_IRQn);
-    }
-
-    /* USER CODE BEGIN CAN2_MspDeInit 1 */
-    /* USER CODE END CAN2_MspDeInit 1 */
-}
-
-/* USER CODE BEGIN 1 */
-
-/* USER CODE END 1 */
-
-/**
-  * @}
-  */
-
-/**
-  * @}
-  */
-
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/EpsilonLights/Src/stm32f4xx_it.c b/EpsilonLights/Src/stm32f4xx_it.c
deleted file mode 100644
index e222a3e4..00000000
--- a/EpsilonLights/Src/stm32f4xx_it.c
+++ /dev/null
@@ -1,110 +0,0 @@
-/**
-  ******************************************************************************
-  * @file    stm32f4xx_it.c
-  * @brief   Interrupt Service Routines.
-  ******************************************************************************
-  *
-  * COPYRIGHT(c) 2016 STMicroelectronics
-  *
-  * Redistribution and use in source and binary forms, with or without modification,
-  * are permitted provided that the following conditions are met:
-  *   1. Redistributions of source code must retain the above copyright notice,
-  *      this list of conditions and the following disclaimer.
-  *   2. Redistributions in binary form must reproduce the above copyright notice,
-  *      this list of conditions and the following disclaimer in the documentation
-  *      and/or other materials provided with the distribution.
-  *   3. Neither the name of STMicroelectronics nor the names of its contributors
-  *      may be used to endorse or promote products derived from this software
-  *      without specific prior written permission.
-  *
-  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
-  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
-  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
-  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
-  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
-  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-  *
-  ******************************************************************************
-  */
-/* Includes ------------------------------------------------------------------*/
-#include "stm32f4xx_hal.h"
-#include "stm32f4xx.h"
-#include "stm32f4xx_it.h"
-#include "cmsis_os.h"
-
-/* USER CODE BEGIN 0 */
-
-/* USER CODE END 0 */
-
-/* External variables --------------------------------------------------------*/
-extern CAN_HandleTypeDef hcan2;
-
-extern TIM_HandleTypeDef htim2;
-
-/******************************************************************************/
-/*            Cortex-M4 Processor Interruption and Exception Handlers         */
-/******************************************************************************/
-
-/**
-* @brief This function handles System tick timer.
-*/
-void SysTick_Handler(void)
-{
-    /* USER CODE BEGIN SysTick_IRQn 0 */
-    /* USER CODE END SysTick_IRQn 0 */
-    osSystickHandler();
-    /* USER CODE BEGIN SysTick_IRQn 1 */
-    /* USER CODE END SysTick_IRQn 1 */
-}
-
-/******************************************************************************/
-/* STM32F4xx Peripheral Interrupt Handlers                                    */
-/* Add here the Interrupt Handlers for the used peripherals.                  */
-/* For the available peripheral interrupt handler names,                      */
-/* please refer to the startup file (startup_stm32f4xx.s).                    */
-/******************************************************************************/
-
-/**
-* @brief This function handles TIM2 global interrupt.
-*/
-void TIM2_IRQHandler(void)
-{
-    /* USER CODE BEGIN TIM2_IRQn 0 */
-    /* USER CODE END TIM2_IRQn 0 */
-    HAL_TIM_IRQHandler(&htim2);
-    /* USER CODE BEGIN TIM2_IRQn 1 */
-    /* USER CODE END TIM2_IRQn 1 */
-}
-
-/**
-* @brief This function handles CAN2 TX interrupts.
-*/
-void CAN2_TX_IRQHandler(void)
-{
-    /* USER CODE BEGIN CAN2_TX_IRQn 0 */
-    /* USER CODE END CAN2_TX_IRQn 0 */
-    HAL_CAN_IRQHandler(&hcan2);
-    /* USER CODE BEGIN CAN2_TX_IRQn 1 */
-    /* USER CODE END CAN2_TX_IRQn 1 */
-}
-
-/**
-* @brief This function handles CAN2 RX0 interrupts.
-*/
-void CAN2_RX0_IRQHandler(void)
-{
-    /* USER CODE BEGIN CAN2_RX0_IRQn 0 */
-    /* USER CODE END CAN2_RX0_IRQn 0 */
-    HAL_CAN_IRQHandler(&hcan2);
-    /* USER CODE BEGIN CAN2_RX0_IRQn 1 */
-    /* USER CODE END CAN2_RX0_IRQn 1 */
-}
-
-/* USER CODE BEGIN 1 */
-
-/* USER CODE END 1 */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/EpsilonLights/startup_stm32f103x6.s b/EpsilonLights/startup_stm32f103x6.s
new file mode 100644
index 00000000..54f8f13a
--- /dev/null
+++ b/EpsilonLights/startup_stm32f103x6.s
@@ -0,0 +1,346 @@
+/**
+  *************** (C) COPYRIGHT 2017 STMicroelectronics ************************
+  * @file      startup_stm32f103x6.s
+  * @author    MCD Application Team
+  * @brief     STM32F103x6 Devices vector table for Atollic toolchain.
+  *            This module performs:
+  *                - Set the initial SP
+  *                - Set the initial PC == Reset_Handler,
+  *                - Set the vector table entries with the exceptions ISR address
+  *                - Configure the clock system   
+  *                - Branches to main in the C library (which eventually
+  *                  calls main()).
+  *            After Reset the Cortex-M3 processor is in Thread mode,
+  *            priority is Privileged, and the Stack is set to Main.
+  ******************************************************************************
+  * @attention
+  *
+  * 
© Copyright (c) 2017 STMicroelectronics.
+  * All rights reserved.

+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+  .syntax unified
+  .cpu cortex-m3
+  .fpu softvfp
+  .thumb
+
+.global g_pfnVectors
+.global Default_Handler
+
+/* start address for the initialization values of the .data section.
+defined in linker script */
+.word _sidata
+/* start address for the .data section. defined in linker script */
+.word _sdata
+/* end address for the .data section. defined in linker script */
+.word _edata
+/* start address for the .bss section. defined in linker script */
+.word _sbss
+/* end address for the .bss section. defined in linker script */
+.word _ebss
+
+.equ  BootRAM, 0xF108F85F
+/**
+ * @brief  This is the code that gets called when the processor first
+ *          starts execution following a reset event. Only the absolutely
+ *          necessary set is performed, after which the application
+ *          supplied main() routine is called.
+ * @param  None
+ * @retval : None
+*/
+
+  .section .text.Reset_Handler
+  .weak Reset_Handler
+  .type Reset_Handler, %function
+Reset_Handler:
+
+/* Copy the data segment initializers from flash to SRAM */
+  movs r1, #0
+  b LoopCopyDataInit
+
+CopyDataInit:
+  ldr r3, =_sidata
+  ldr r3, [r3, r1]
+  str r3, [r0, r1]
+  adds r1, r1, #4
+
+LoopCopyDataInit:
+  ldr r0, =_sdata
+  ldr r3, =_edata
+  adds r2, r0, r1
+  cmp r2, r3
+  bcc CopyDataInit
+  ldr r2, =_sbss
+  b LoopFillZerobss
+/* Zero fill the bss segment. */
+FillZerobss:
+  movs r3, #0
+  str r3, [r2], #4
+
+LoopFillZerobss:
+  ldr r3, = _ebss
+  cmp r2, r3
+  bcc FillZerobss
+
+/* Call the clock system intitialization function.*/
+    bl  SystemInit
+/* Call static constructors */
+    bl __libc_init_array
+/* Call the application's entry point.*/
+  bl main
+  bx lr
+.size Reset_Handler, .-Reset_Handler
+
+/**
+ * @brief  This is the code that gets called when the processor receives an
+ *         unexpected interrupt.  This simply enters an infinite loop, preserving
+ *         the system state for examination by a debugger.
+ *
+ * @param  None
+ * @retval : None
+*/
+    .section .text.Default_Handler,"ax",%progbits
+Default_Handler:
+Infinite_Loop:
+  b Infinite_Loop
+  .size Default_Handler, .-Default_Handler
+/******************************************************************************
+*
+* The minimal vector table for a Cortex M3.  Note that the proper constructs
+* must be placed on this to ensure that it ends up at physical address
+* 0x0000.0000.
+*
+******************************************************************************/
+  .section .isr_vector,"a",%progbits
+  .type g_pfnVectors, %object
+  .size g_pfnVectors, .-g_pfnVectors
+
+
+g_pfnVectors:
+
+  .word _estack
+  .word Reset_Handler
+  .word NMI_Handler
+  .word HardFault_Handler
+  .word MemManage_Handler
+  .word BusFault_Handler
+  .word UsageFault_Handler
+  .word 0
+  .word 0
+  .word 0
+  .word 0
+  .word SVC_Handler
+  .word DebugMon_Handler
+  .word 0
+  .word PendSV_Handler
+  .word SysTick_Handler
+  .word WWDG_IRQHandler
+  .word PVD_IRQHandler
+  .word TAMPER_IRQHandler
+  .word RTC_IRQHandler
+  .word FLASH_IRQHandler
+  .word RCC_IRQHandler
+  .word EXTI0_IRQHandler
+  .word EXTI1_IRQHandler
+  .word EXTI2_IRQHandler
+  .word EXTI3_IRQHandler
+  .word EXTI4_IRQHandler
+  .word DMA1_Channel1_IRQHandler
+  .word DMA1_Channel2_IRQHandler
+  .word DMA1_Channel3_IRQHandler
+  .word DMA1_Channel4_IRQHandler
+  .word DMA1_Channel5_IRQHandler
+  .word DMA1_Channel6_IRQHandler
+  .word DMA1_Channel7_IRQHandler
+  .word ADC1_2_IRQHandler
+  .word USB_HP_CAN1_TX_IRQHandler
+  .word USB_LP_CAN1_RX0_IRQHandler
+  .word CAN1_RX1_IRQHandler
+  .word CAN1_SCE_IRQHandler
+  .word EXTI9_5_IRQHandler
+  .word TIM1_BRK_IRQHandler
+  .word TIM1_UP_IRQHandler
+  .word TIM1_TRG_COM_IRQHandler
+  .word TIM1_CC_IRQHandler
+  .word TIM2_IRQHandler
+  .word TIM3_IRQHandler
+  .word 0
+  .word I2C1_EV_IRQHandler
+  .word I2C1_ER_IRQHandler
+  .word 0
+  .word 0
+  .word SPI1_IRQHandler
+  .word 0
+  .word USART1_IRQHandler
+  .word USART2_IRQHandler
+  .word 0
+  .word EXTI15_10_IRQHandler
+  .word RTC_Alarm_IRQHandler
+  .word USBWakeUp_IRQHandler
+  .word 0
+  .word 0
+  .word 0
+  .word 0
+  .word 0
+  .word 0
+  .word 0
+  .word BootRAM        /* @0x108. This is for boot in RAM mode for
+                          STM32F10x Low Density devices.*/
+
+/*******************************************************************************
+*
+* Provide weak aliases for each Exception handler to the Default_Handler.
+* As they are weak aliases, any function with the same name will override
+* this definition.
+*
+*******************************************************************************/
+
+  .weak NMI_Handler
+  .thumb_set NMI_Handler,Default_Handler
+
+  .weak HardFault_Handler
+  .thumb_set HardFault_Handler,Default_Handler
+
+  .weak MemManage_Handler
+  .thumb_set MemManage_Handler,Default_Handler
+
+  .weak BusFault_Handler
+  .thumb_set BusFault_Handler,Default_Handler
+
+  .weak UsageFault_Handler
+  .thumb_set UsageFault_Handler,Default_Handler
+
+  .weak SVC_Handler
+  .thumb_set SVC_Handler,Default_Handler
+
+  .weak DebugMon_Handler
+  .thumb_set DebugMon_Handler,Default_Handler
+
+  .weak PendSV_Handler
+  .thumb_set PendSV_Handler,Default_Handler
+
+  .weak SysTick_Handler
+  .thumb_set SysTick_Handler,Default_Handler
+
+  .weak WWDG_IRQHandler
+  .thumb_set WWDG_IRQHandler,Default_Handler
+
+  .weak PVD_IRQHandler
+  .thumb_set PVD_IRQHandler,Default_Handler
+
+  .weak TAMPER_IRQHandler
+  .thumb_set TAMPER_IRQHandler,Default_Handler
+
+  .weak RTC_IRQHandler
+  .thumb_set RTC_IRQHandler,Default_Handler
+
+  .weak FLASH_IRQHandler
+  .thumb_set FLASH_IRQHandler,Default_Handler
+
+  .weak RCC_IRQHandler
+  .thumb_set RCC_IRQHandler,Default_Handler
+
+  .weak EXTI0_IRQHandler
+  .thumb_set EXTI0_IRQHandler,Default_Handler
+
+  .weak EXTI1_IRQHandler
+  .thumb_set EXTI1_IRQHandler,Default_Handler
+
+  .weak EXTI2_IRQHandler
+  .thumb_set EXTI2_IRQHandler,Default_Handler
+
+  .weak EXTI3_IRQHandler
+  .thumb_set EXTI3_IRQHandler,Default_Handler
+
+  .weak EXTI4_IRQHandler
+  .thumb_set EXTI4_IRQHandler,Default_Handler
+
+  .weak DMA1_Channel1_IRQHandler
+  .thumb_set DMA1_Channel1_IRQHandler,Default_Handler
+
+  .weak DMA1_Channel2_IRQHandler
+  .thumb_set DMA1_Channel2_IRQHandler,Default_Handler
+
+  .weak DMA1_Channel3_IRQHandler
+  .thumb_set DMA1_Channel3_IRQHandler,Default_Handler
+
+  .weak DMA1_Channel4_IRQHandler
+  .thumb_set DMA1_Channel4_IRQHandler,Default_Handler
+
+  .weak DMA1_Channel5_IRQHandler
+  .thumb_set DMA1_Channel5_IRQHandler,Default_Handler
+
+  .weak DMA1_Channel6_IRQHandler
+  .thumb_set DMA1_Channel6_IRQHandler,Default_Handler
+
+  .weak DMA1_Channel7_IRQHandler
+  .thumb_set DMA1_Channel7_IRQHandler,Default_Handler
+
+  .weak ADC1_2_IRQHandler
+  .thumb_set ADC1_2_IRQHandler,Default_Handler
+
+  .weak USB_HP_CAN1_TX_IRQHandler
+  .thumb_set USB_HP_CAN1_TX_IRQHandler,Default_Handler
+
+  .weak USB_LP_CAN1_RX0_IRQHandler
+  .thumb_set USB_LP_CAN1_RX0_IRQHandler,Default_Handler
+
+  .weak CAN1_RX1_IRQHandler
+  .thumb_set CAN1_RX1_IRQHandler,Default_Handler
+
+  .weak CAN1_SCE_IRQHandler
+  .thumb_set CAN1_SCE_IRQHandler,Default_Handler
+
+  .weak EXTI9_5_IRQHandler
+  .thumb_set EXTI9_5_IRQHandler,Default_Handler
+
+  .weak TIM1_BRK_IRQHandler
+  .thumb_set TIM1_BRK_IRQHandler,Default_Handler
+
+  .weak TIM1_UP_IRQHandler
+  .thumb_set TIM1_UP_IRQHandler,Default_Handler
+
+  .weak TIM1_TRG_COM_IRQHandler
+  .thumb_set TIM1_TRG_COM_IRQHandler,Default_Handler
+
+  .weak TIM1_CC_IRQHandler
+  .thumb_set TIM1_CC_IRQHandler,Default_Handler
+
+  .weak TIM2_IRQHandler
+  .thumb_set TIM2_IRQHandler,Default_Handler
+
+  .weak TIM3_IRQHandler
+  .thumb_set TIM3_IRQHandler,Default_Handler
+
+  .weak I2C1_EV_IRQHandler
+  .thumb_set I2C1_EV_IRQHandler,Default_Handler
+
+  .weak I2C1_ER_IRQHandler
+  .thumb_set I2C1_ER_IRQHandler,Default_Handler
+
+  .weak SPI1_IRQHandler
+  .thumb_set SPI1_IRQHandler,Default_Handler
+
+  .weak USART1_IRQHandler
+  .thumb_set USART1_IRQHandler,Default_Handler
+
+  .weak USART2_IRQHandler
+  .thumb_set USART2_IRQHandler,Default_Handler
+
+  .weak EXTI15_10_IRQHandler
+  .thumb_set EXTI15_10_IRQHandler,Default_Handler
+
+  .weak RTC_Alarm_IRQHandler
+  .thumb_set RTC_Alarm_IRQHandler,Default_Handler
+
+  .weak USBWakeUp_IRQHandler
+  .thumb_set USBWakeUp_IRQHandler,Default_Handler
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/