Problem using 2 module INA226 in I2C protocol

[Gagge89]

Hi.. I have a problem to use 2 module INA226 with protocol I2C.
I write this sketch but it doesn't work. the Arduino IDE give me errors. Can you help me?

`/*
INA226 Bi-directional Current/Power Monitor. Simple Example.
Read more: http://www.jarzebski.pl/arduino/czujniki-i-sensory/cyfrowy-czujnik-pradu-mocy-ina226.html
GIT: https://github.com/jarzebski/Arduino-INA226
Web: http://www.jarzebski.pl
(c) 2014 by Korneliusz Jarzebski
*/

#include <Wire.h>
#include <INA226.h>

INA226 ina_5V;
INA226 ina_3.3V(0x45);

void checkConfig()
{

Serial.print("Max possible current 5V: ");
Serial.print(ina_5V.getMaxPossibleCurrent());
Serial.println(" A");

Serial.print("Max current 5V: ");
Serial.print(ina_5V.getMaxCurrent());
Serial.println(" A");

Serial.print("Max shunt voltage 5V: ");
Serial.print(ina_5V.getMaxShuntVoltage());
Serial.println(" V");

Serial.print("Max power 5V: ");
Serial.print(ina_5V.getMaxPower());
Serial.println(" W");

Serial.print("Max possible current 3.3V: ");
Serial.print(ina_3.3V.getMaxPossibleCurrent());
Serial.println(" A");

Serial.print("Max current 3.3V: ");
Serial.print(ina_3.3V.getMaxCurrent());
Serial.println(" A");

Serial.print("Max shunt voltage 3.3V: ");
Serial.print(ina_3.3V.getMaxShuntVoltage());
Serial.println(" V");

Serial.print("Max power 3.3V: ");
Serial.print(ina_3.3V.getMaxPower());
Serial.println(" W");

}

void setup()
{
Serial.begin(115200);

Serial.println("Initialize INA226");
Serial.println("-----------------------------------------------");

// Default INA226 address is 0x40
ina_5V.begin();
ina_3.3V.begin();

// Configure INA226
ina_5V.configure(INA226_AVERAGES_1, INA226_BUS_CONV_TIME_1100US, INA226_SHUNT_CONV_TIME_1100US, INA226_MODE_SHUNT_BUS_CONT);
ina_3.3V.configure(INA226_AVERAGES_1, INA226_BUS_CONV_TIME_1100US, INA226_SHUNT_CONV_TIME_1100US, INA226_MODE_SHUNT_BUS_CONT);

// Calibrate INA226. Rshunt = 0.1 ohm, Max excepted current = 4A
ina_5V.calibrate(0.1, 4);
ina_3.3V.calibrate(0.1, 4);

// Display configuration
checkConfig();

Serial.println("-----------------------------------------------");
}

void loop()
{
Serial.print("Bus voltage 5V: ");
Serial.print(ina_5V.readBusVoltage(), 2); // valore a 2 cifre decimali
Serial.println(" V");

Serial.print("Bus power 5V: ");
Serial.print(ina_5V.readBusPower(), 3); // valore a 3 cifre decimali
Serial.println(" W");

Serial.print("Shunt voltage 5V: ");
Serial.print(ina_5V.readShuntVoltage(), 5);
Serial.println(" V");

Serial.print("Shunt current 5V: ");
Serial.print(ina_5V.readShuntCurrent(), 4); // valore a 3 cifre decimali
Serial.println(" A");

Serial.print("Bus voltage 3.3V: ");
Serial.print(ina_3.3V.readBusVoltage(), 2); // valore a 2 cifre decimali
Serial.println(" V");

Serial.print("Bus power 3.3V: ");
Serial.print(ina_3.3V.readBusPower(), 3); // valore a 3 cifre decimali
Serial.println(" W");

Serial.print("Shunt voltage 3.3V: ");
Serial.print(ina_3.3V.readShuntVoltage(), 5);
Serial.println(" V");

Serial.print("Shunt current 3.3V: ");
Serial.print(ina_3.3V.readShuntCurrent(), 4); // valore a 3 cifre decimali
Serial.println(" A");

Serial.println("");
delay(1000);
}`

[Rupesh-Jogani]

Just add the new address in the Header file.
You can do that by opening the header file in Notepad by defining the new address
You might need to tweak some code in Header as well as CPP file.