hr_06_chemical_properties.qmd

---
output: html_document
editor_options: 
  chunk_output_type: console
---

# Chemical properties {#sec-chem}

```{r}
library(dplyr)
library(tibble)
library(gt)
library(gtExtras)
```

## Field tests {#sec-ft}

Field tests support confident soil profile descriptions in the field by providing immediate indications of key soil chemical properties. As well as informing the description itself, the tests can help guide sampling decisions and later choice of laboratory analyses. In some cases, they can act as quality control measures (e.g. large inconsistencies in pH between field and laboratory may indicate unwanted sample oxidation in acid sulfate soils).

Field tests do have limited precision and accuracy vs their laboratory equivalents, due to their simplicity and short observation times. Where field tests are not conclusive, laboratory testing may still be warranted.

Field tests should be performed down-profile, with at least one sample tested per horizon. Samples should be taken from the mid-point of each horizon. Additional samples in transition zones may also be of interest. Properties within the upper part of the first B horizon can be diagnostic in soil classification.

::: {#nte-chemnzsc .callout-note appearance="minimal" collapse="true" title="Field chemical tests and the New Zealand Soil Classification (NZSC)"}
For classifying using the NZSC, particular tests down to a certain depth may be required. At the order level, these are:

-   **Gley soils:** Detectable ferrous ions (Fe^2+^) in the soil solution within the top 30 cm, signifying a reduced/anoxic environment (@sec-ft-rdx). A slaking test may be required to confirm absence of an underlying duripan (@sec-ft-slak)
-   **Ultic soils:** pH below 5.5 anywhere between the base of the A horizon and 60 cm depth (@sec-ft-phf or @sec-ft-phfw)
-   **Allophanic soils:** Strong pH response to sodium fluoride in at least 35 cm of the top 60 cm (@sec-ft-naf)
-   **Melanic soils:** Fine earth fraction reacts with 10% HCl, signifying carbonate presence (@sec-ft-ca)
-   **Semiarid soils:** pH of 7.5 or more within the top 90 cm (150 cm if sandy or skeletal) (@sec-ft-phf or @sec-ft-phfw)
-   **Oxidic soils:** No pH response to sodium fluoride within the diagnostic oxidic horizon(s) (@sec-ft-naf)
-   **Pallic soils:** Where a calcareous horizon is part of the profile, confirmation of its presence with 10% HCl (@sec-ft-ca)
-   **Brown soils:** at least moderate pH response to sodium fluoride in the uppermost subhorizon of the B horizon. (@sec-ft-naf)

pH, carbonate, allophane and salinity tests are also common diagnostics at the group and subgroup level.
:::

### Colourimetric field pH (pH~f~) {#sec-ft-phf}

This method, after @raupach1959, requires the use of a pre-made kit containing universal pH indicator, barium sulfate powder, and a calibrated colour card for interpreting results. These kits can be purchased at hardware or garden supply stores as well as specialist environmental field supply stores. The tests are simple but only precise to ± 0.5 units, and accurate (vs laboratory-based testing) to around the same degree. They are usually valid over pH range 2-10.

*Equipment*

-   Field pH kit:
    -   universal indicator
    -   barium sulfate powder
    -   calibrated colour interpretation card
    -   small sample containers or plastic tray
    -   stirring stick

*Procedure*

1.  With clean hands or a small scoop, remove \~1-2 cm^2^ soil into a small container. Mix or crush the sample lightly to break open small peds.
2.  Sprinkle the sample surface with just enough barium sulfate powder to cover. This is used to make it easier to see the pH indicator colour.
3.  Add a couple of drops of pH indicator. Match the indicator colour to the card provided and record the pH of the closest match (e.g. [40 cm - 5.5]{.ceg}). Do not interpolate between chips. Do not wait to read the pH - readings are unreliable after the sample has dried.

::: {#nte-phvar .callout-note appearance="minimal" collapse="true" title="Sources of variation between pH~f~ and laboratory pH"}
Some variability between colorimetric field and electronic laboratory pH is expected. Reasons for the variability may include:

-   The quality of the reagents in use, the kit's age and how carefully it has been stored. The dye recipe needs to have been followed accurately so that the resulting colours match the calibration card. Impurities in the supplied barium sulfate powder can also cause issues. The calibration card itself needs to be printed with accurate colours, waterproofed, and not left to bleach in the sun.
-   Operators need full colour vision to interpret the card correctly. While diagnosed colour blindness is relatively rare, many people have minor colour-recognition limitations without knowing it. Taking a colour vision test periodically is recommended.
-   Samples taken for laboratory analysis may react during transport, in storage or during sample processing.
:::

### Field pH in water (pH~fw~) {#sec-ft-phfw}

pH~fw~ is measured with a field-ready electronic pH meter. Electronic meters are precise and can measure the full 0-14 pH range, but are sensitive to temperature fluctuations and must be regularly calibrated. Always refer to the device manual for specific maintenance requirements.

*Equipment*

-   Field-ready electronic pH meter (ideally with a temperature sensor)
-   Deionised (DI) water or demineralised (DM) water
-   Small sample containers (e.g. 50 mL centrifuge tubes)
-   Stirring sticks

*Procedure*

1.  With clean hands or a small scoop, remove \~1-2 cm^2^ soil into a small container. Mix with DI or DM water to a loose paste, ensuring that the mix is deep enough for the pH probe to be adequately covered.
2.  Insert the pH probe into the sample and wait for the reading to stabilise to 1 decimal place (No change for 10 seconds). Do not stir the sample with the probe.
3.  Record the reading and the depth it was taken from (e.g. [40 cm - 5.2]{.ceg}).
4.  Thoroughly rinse the probe before testing the next sample.

::: {#tip-shand .callout-tip appearance="minimal" collpase="true" title="Sample handling"}
Make sure to sample with clean hands; tests can be easily contaminated by residues. In particular, sunscreens will cause a falsely high pH reading.
:::

### Field pH in hydrogen peroxide (pH~fox~) {#sec-ft-phfox}

Field pH in concentrated hydrogen peroxide (30% H~2~O~2~) is paired with field pH in water to diagnose the presence of FeS~2~ (iron sulfide, or pyrite) and thus the presence of acid sulfate soil materials. A significant drop in pH~fox~ vs pH~fw~ is considered diagnostic; see the discussion in @sullivan2018, section A1.4.4 for further details.

The following method is reproduced from @sullivan2018, section A1.4.3.

*Equipment*

-   Field-ready electronic pH meter (ideally with a temperature sensor)
-   Concentrated hydrogen peroxide (30% H~2~O~2~)
-   Deionised (DI) water or demineralised (DM) water
-   Small sample containers (e.g. 50 mL centrifuge tubes) without lids.
-   Stirring sticks

*Procedure*

1.  With clean hands or a small scoop, remove \~1-2 cm^2^ soil into each tube.
2.  Add enough H~2~O~2~ to cover each sample, and stir briefly. **Do not cap and shake the tubes**.
3.  Allow up to 15 minutes for any reaction to occur, especially in cool weather. Placing the rack in the sun may help progress the reaction. Note that strong reactions can sometimes occur almost instantly - observe the samples from a short distance and don't peer into the tubes.
4.  Where reactions occur, note their violence using the scale in @tbl-ft-foxrx. If excessive, the reaction may be tamped down by adding a very small amount of DI water.
5.  Where reactions occur, wait for them to settle and add a little more H~2~O~2~. Repeat until the reaction no longer occurs.
6.  Once reactions have fully completed and the tubes have cooled, measure the pH of each sample with the electronic meter. Record to the nearest 0.1 units as for pH~fw~, and rinse the probe thoroughly between readings.

::: {#wrn-prox .callout-warning appearance="minimal" collapse="true" title="Safe handling and preparation of hydrogen peroxide"}
-   Concentrated hydrogen peroxide is highly corrosive. Wear safety glasses and gloves when handling, and in a field situation make sure that there is access to plenty of clean water for rinsing.
-   Before bringing H~2~O~2~ into the field, it must be buffered to pH 4.5-5.5. While stirring, add a few drops of dilute NaOH and regularly check the pH with a calibrated electrode until the correct range is reached. Allow the H~2~O~2~ to stand for 15 minutes and then recheck the pH.
-   As H~2~O~2~ degrades over time, only buffer small quantities at a time and refrigerate when not in use.
-   In the field, H~2~O~2~ containers should be kept out of direct sunlight and preferably in a small cooler, as excessive heat will cause the H~2~O~2~ to break down, releasing oxygen. This can cause its container to rupture or spit when opened. Only take small containers into the field, and monitor them for signs of elevated internal pressure (e.g. bulging). Make sure all containers are clearly labelled.
:::

```{r}
#| label: tbl-ft-foxrx
#| tbl-cap: "Hydrogen peroxide reaction strength ratings"

dat_ft_foxrx <-
  tribble(~Code, ~Name, ~Description, 
          'N', 'No reaction',  'No fizzing or bubbling after 15 minutes',
          'L', 'Slight reaction', 'Sample fizzes or bubbles slightly but does not steam',
          'M', 'Moderate reaction', 'Sample bubbles and steams slightly but does not completely boil. Unlikely to continue reacting if more peroxide is added',
          'H', 'High reaction', 'Sample boils and steams but does not boil over. May continue to react when more peroxide is added',
          'X', 'Explosive reaction', 'Sample rapidly boils over and puts off considerable steam; likely to continue to react when more peroxide is added' 
  )

tbl_ft_foxrx <- gt(dat_ft_foxrx) |>
  tab_options(
    column_labels.font.weight = 'bold', 
    heading.title.font.weight = 'bold',
    table.align = 'center',
    table.width = '85%'
  ) |>
  tab_style(style = list(cell_text(color  = 'red', 
                                   weight = 'bold',
                                   align  = 'center')),
            locations = cells_body(columns = 1)) |>
  cols_width(Code ~pct(10), Name ~ pct(20))
  
tbl_ft_foxrx
```

::: {.content-visible when-format='docx'}
delete me 
:::

::: {#nte-assinc .callout-note appearance="minimal" collapse="true" title="Incubation methods for Acid Sulfate Soils"}
Field-adjacent incubation methods are available as an alternative low-cost method of identifying acid sulfate soils. These involve minimal equipment and no hazardous chemicals, but can take up to three months to complete. See [@sullivan2018a], Appendix C for further information.
:::

### Electrical conductivity (EC~f~) {#sec-ft-ec}

The soil solution's EC~f~ estimates its soluble salt content, which can affect plant nutrition and water uptake. Salinity is a diagnostic criteria in the NZSC, used within the Gley, Semi-Arid, Recent and Raw orders. In New Zealand, a 1:5 ratio of soil to water is used in the laboratory, and so this must be matched in the field.

*Equipment*

-   Field-ready electrical conductivity meter (ideally with a temperature sensor)
-   Deionised (DI) water or demineralised (DM) water
-   Small sample containers (e.g. 50 mL centrifuge tubes) with lids.
-   Stirring sticks

*Procedure*

1.  With clean hands or a small scoop, place soil in each tube up to the 5 mL mark. Top up with water to 30 mL.
2.  Cap and shake each sample vigorously for 30s, then allow the samples to settle for a few minutes.
3.  Use the EC meter to record the solution conductivity. Report to the nearest 0.1 dS/m.
4.  Rinse the probe thoroughly between measurements.

::: {#nte-condu .callout-note appearance="minimal" collapse="true" title="Conductivity units"}
EC is most commonly reported in units of millisiemens/centimetre (mS/cm) or decisiemens per metre (dS/m), which are numerically equivalent. Other units less commonly used require specific conversion, e.g. electronic meters may report in µS/cm. 1 mS/cm = 1000 µS/cm.
:::

### Calcium carbonate (Ca~f~) {#sec-ft-ca}

While large chunks of calcium carbonate (CaCO~3~) in the form of shells or rock are easy to spot, CaCO~3~ in the fine earth is not, and there can also be some doubt about the composition of secondary features. This test should be considered for use when working in limestone-containing country, where field pH \> 7, or when white or pale concentrations or coatings are observed.

Calcium carbonate reacts with acidic solutions in a neutralisation reaction, releasing water, carbon dioxide and heat as it becomes a salt. The reaction is rapid and causes a soil sample to 'fizz' visibly. 10% (or 1 *M*) HCl is used for this test as it is stable, cheap and relatively safe while still reacting vigorously.

*Equipment*

-   10% or 1M Hydrochloric acid, stored in a small dropper bottle
-   small sample containers or plastic tray

*Procedure*

1.  With clean hands or a small scoop, remove \~1-2 cm^2^ soil into a small container. Lightly crush to break up peds and/or concentrations.
2.  Using a dropper bottle, add a drop or two of HCl and observe closely.
3.  Record the vigour of the reaction using @tbl-ft-hcl.

HCl can also be applied directly to a soil exposure, but be careful not to include the tested patches in any soil samples.

::: {#wrn-hcl .callout-warning appearance="minimal" collapse="true" title="Safe handling and preparation of HCl"}
-   HCl is corrosive. Wear safety glasses and gloves when handling, and in a field situation make sure that there is access to plenty of clean water for rinsing.
-   Don't transport large quantities of HCl, even dilute. A 25-50 mL bottle will normally last for weeks of fieldwork.
-   Make sure HCl containers are clearly labelled. For dropper bottles with soft plastic or rubber lids, monitor for degradation.
:::

```{r}
#| label: tbl-ft-hcl
#| tbl-cap: "Hydrochloric acid reaction ratings"

dat_ft_hcl <-
  tribble(~Code, ~Name, ~Description, 
          'N', 'No reaction',  'No audible or visible fizzing',
          'L', 'Slight reaction', 'Fizzing faintly audible and barely visible',
          'M', 'Moderate reaction', 'Fizzing audible and clearly visible, small bubbles ≤ 3 mm diameter',
          'H', 'High reaction', 'Fizzing easily audible and visible, bubbles up to 7 mm diameter'
  )

tbl_ft_hcl <- gt(dat_ft_hcl) |>
  tab_options(
    column_labels.font.weight = 'bold', 
    heading.title.font.weight = 'bold',
    table.align = 'center',
    table.width = '85%'
  ) |>
  tab_style(style = list(cell_text(color  = 'red', 
                                   weight = 'bold',
                                   align  = 'center')),
            locations = cells_body(columns = 1)) |>
  cols_width(Code ~pct(10), Name ~ pct(20))
  
tbl_ft_hcl
```

::: {.content-visible when-format='docx'}
delete me 
:::

::: {#nte-meascarb .callout-note appearance="minimal" collapse="true" title="Measuring CaCO~3~"}
While @milne1995 and some other publications [@rayment2011; @kalra1991] have attempted to use the degree of fizzing to estimate CaCO~3~ % content, the estimates and descriptions of fizzing vary and are not considered highly reliable. If a precise numeric estimate of CaCO~3~ % is required, it should be measured under laboratory conditions.
:::

### Manganese (Mn~f~) {#sec-ft-mn}

Manganese concentrations in soil are dark and often very small, so may be missed or mistaken for other minerals. Manganese oxides react to H~2~O~2~ in a similar fashion to iron sulfide (see @sec-ft-phfox). This test uses a safer dilute H~2~O~2~ solution. This test should be considered for use where dark flecks are observed in the soil profile, particularly under imperfect to poor drainage conditions (see @sec-in-hdrng).

*Equipment*

-   Dilute (3-6%) H~2~O~2~ solution, stored in a small dropper bottle
-   Small sample containers or plastic tray

*Procedure*

1.  With clean hands or a small scoop, remove \~1-2 cm^2^ soil into a small container. Lightly crush to break up peds and/or concentrations.
2.  Using a dropper bottle, add a drop or two of dilute H~2~O~2~ and observe closely for fizzing.
3.  Record the presence or absence of a reaction (e.g. [40 cm - ✔]{.ceg}).

Dilute H~2~O~2~ can also be applied directly to a soil exposure, but be careful not to include the tested patches in any soil samples. Note that H~2~O~2~ will also react with organic material, so this test is not definitive in highly organic samples. Using concentrated H~2~O~2~ will increase the likelihood of misinterpretation as it will attack organic material more vigorously.

### Reactive aluminium (NaF~f~) {#sec-ft-naf}

This test indicates the presence of reactive hydroxy-aluminium sites on soil minerals. In New Zealand, these sites are most often associated with the presence of the minerals allophane and imogolite. Reactive hydroxy-aluminium sites can also be found on ferrihydrite and aluminium-humus complexes, especially in podzolic B horizons. [The principle of the method is that fluoride ions at about pH 7 react with hydroxy-aluminium to release hydroxyl ions, causing a rise in pH. The test conditions have been chosen so that the released OH^-^ from soils containing reactive hydroxy-aluminium turn phenolphthalein indicator reagent red (pH \> 9) whilst most other soils remain at lower pH values so that the indicator remains colourless.]{.milne}

*Equipment*

-   Saturated aqueous NaF solution (1 M NaF, maintained in the presence of an excess of undissolved NaF)
-   Filter paper (Whatman No. 42 or similar) treated with phenolphthalein indicator (0.5% dissolved in 50% ethanol) and subsequently dried.

*Procedure*

1.  With clean hands or a small scoop, place \~0.5 cm^2^ soil on a piece of pre-treated filter paper. Lightly crush to break up peds and put the soil in firm contact with the paper.
2.  Using a dropper bottle, add a drop or two of 1 M NaF (enough to wet the sample but not flood it) and wait up to 2 minutes.
3.  Record the reaction intensity using @tbl-ft-naf (e.g. [40 cm - M]{.ceg}).

::: {#wrn-naf .callout-warning appearance="minimal" collapse="true" title="Safe handling and preparation of NaF"}
-   NaF is toxic. Wear safety glasses and gloves when handling, and in a field situation make sure that there is access to plenty of clean water for rinsing.
-   Make sure NaF containers are clearly labelled.
:::

```{r}
#| label: tbl-ft-naf
#| tbl-cap: "Sodium fluoride reaction ratings"

# Eyeballed these, but tweaked them a little using field photos
# Soil materials sometimes interfere with the apparent colour a bit but
# mentioning that feels like TMI
dat_ft_naf <-
  tribble(~Code, ~Name, ~Description, ~Colour, 
          'N', 'No reaction',  'No colour change', '#FFFFFF',
          'L', 'Slight reaction', 'Paper turns faint pink within two minutes',  '#FFBADE',
          'M', 'Moderate reaction', 'Paper turns moderate pink, usually within 30 seconds', '#CF3A69',
          'H', 'Strong reaction', 'Paper turns dark pink, usually instantly', '#A11844'
  ) |>
  dplyr::mutate(fa_icon = 'fas fa-circle')

tbl_ft_naf <- gt(dat_ft_naf) |>
  tab_options(
    column_labels.font.weight = 'bold', 
    heading.title.font.weight = 'bold',
    table.align = 'center',
    table.width = '85%'
  ) |>
  tab_style(style = list(cell_text(color  = 'red', 
                                   weight = 'bold',
                                   align  = 'center')),
            locations = cells_body(columns = 1)) |>
  fmt_icon(columns    = fa_icon, 
           fill_color = from_column("Colour"), 
           height     = '1.5em',
           fill_alpha = 0.9) |>
  cols_hide(Colour) |>
  cols_label(fa_icon = 'Colour') |>
  cols_width(Code ~pct(10), Name ~ pct(20), fa_icon ~ pct(10))
  
tbl_ft_naf
```

::: {.content-visible when-format='docx'}
delete me 
:::

::: {#imp-naf .callout-important appearance="minimal" collapse="true" title="Use caution interpreting the NaF~f~ test"}
-   The presence of alkaline conditions and/or free calcium carbonate will cause a strong false positive for this test, as the NaF will precipitate to CaF~2~ and yield Na~2~CO~3~. When in doubt, pre-screening with 10% HCl or a field pH test is recommended to avoid confusion.
-   The presence of organic matter can interfere with the test by buffering the pH change.
-   Soils containing free aluminium (Al^2+^) may also react.
:::

::: {#nte-nafint .callout-note appearance="minimal" collapse="true" title="NaF~f~ test interpretation"}
Scales used to interpret the NaF~f~ test have been inconsistently presented over the decades since its original publication, with a tendency to get more complicated over time. The scale presented in @tbl-ft-naf is a return towards the simpler schemas seen in early reporting.

While a correlation can be made between P-retention and NaF reaction intensity within younger volcanic soils (Allophanic and Pumice soil orders) the correlation does not hold across all soils.
:::

### Reducing conditions {#sec-ft-rdx}

Reducing conditions can be suggested by low-chroma soil colours, redox mottling and other indicators of poor drainage. More confident diagnoses can be made by including field testing for reduced iron (Fe^2+^) as an indicator of persistently reducing conditions. Rapid testing for Fe^2+^ can be accomplished using 2,2'-Bipyridine (previously/also known as ⍺-⍺-dipyridyl) dye, which turns pinkish red in the presence of Fe^2+^. Test strips are also commercially available and may prove easier to use in the field [@berkowitz2017]. Note that these tests should only be conducted on wet or moist soils; soils that are in a slightly moist to dry state will not be experiencing reducing conditions.

*Procedure*

1.  With clean hands or a small scoop, remove \~1-2 cm^2^ soil into a small container or a surface with a white background.
2.  Depending on method:
    a.  If using indicator strips, press the strip gently against the sample surface for a few seconds, then remove and check for colour change.
    b.  If using 2,2'-Bipyridine dye, apply a few drops to the sample and watch for a colour change.
3.  Record the presence or absence of a reaction (e.g. [40 cm - ✔]{.ceg}).

In both cases work quickly, as if reduced, the sample will oxidise rapidly on excavation.

::: {#wrn-aasaf .callout-warning appearance="minimal" collapse="true" title="Safe handling of 2,2'-Bipyridine solution"}
Some manuals have suggested the use of a spray bottle to apply 2,2'-Bipyridine to an exposure or extracted sample. This is not recommended due to the chemical's toxicity. See [@nationalcenterforbiotechnologyinformation2024] for further details.
:::

::: {#nte-reduc .callout-note appearance="minimal" collapse="true" title="Other methods of assessing reduction"}
Current best practice for research-grade monitoring of redox potential in soils involves the use of IRIS indicator devices [@sapkota2022], sometimes in concert with electronic sensors. IRIS devices require specialist construction, installation for several weeks and careful post-processing.
:::

### Water repellence {#sec-ft-wtrep}

Water repellence in soils results from hydrophobic organic compounds (e.g. plant leaf waxes) accumulating under a specific range of soil moisture conditions [@dekker2009]. Repellency is thus locally and seasonally variable, and usually confined to surface layers. Water repellence is most commonly assessed under field conditions using distilled water.

*Equipment*

-   Deionised (DI) or demineralised (DM) water, stored in a small dropper bottle
-   Small sample containers or plastic tray

*Procedure*

1.  With clean hands or a small scoop, remove \~1-2 cm^2^ soil into a small container. Leave the sample intact.
2.  Use a dropper to place a single drop of distilled water onto the soil surface. Measure how long it takes for the drop to be absorbed.
3.  If the drop takes longer than 5 seconds to disappear, record a positive result (e.g. [40 cm - ✔]{.ceg}).

### Rapid slaking and dispersion {#sec-ft-slak}

Soil aggregates can slake, or disintegrate, when wet up from a dry state, as trapped air rushes out of pore spaces. Over a longer time period, clay swelling may also contribute to aggregate breakdown by slaking. Aggregate resistance to slaking behaviour is modified by organic matter content and clay mineral type. Dispersive behaviour also causes aggregate breakdown in water but is driven by relative dominance of Na^+^ ions (and to some extent Mn^2+^ and K^+^) on ion exchange sites.

Field testing can reveal soils that are prone to rapid slaking and dispersion. However, soils that are only slightly prone to these behaviours may not be detected in the short assessment time described below. The test also requires dry soil samples, which can be hard to come by under New Zealand field conditions. Running the test over a 2 hour period on air-dried peds after fieldwork will often be more useful. The laboratory equivalent assessment runs over a minimum of 20 hours [@standardsaustralia; @emerson2002].

*Equipment*

-   Deionised (DI) or demineralised (DM) water
-   Shallow dish, 3-5 cm deep and 15-30 cm in diameter

*Procedure*

1.  Set out a testing dish in a sheltered location and fill with at least 2-3 cm of DI or DM water (enough to completely cover added peds). Allow to settle.
2.  Carefully add one or two dry peds from each massive or pedal soil horizon, working clockwise around the dish. Minimise disturbing the water.
3.  Observe the samples after waiting 10 minutes. Rate their slaking behaviour using @tbl-ft-slak. Rate their dispersive behaviour using @tbl-ft-disp.

```{r}
#| label: tbl-ft-slak
#| tbl-cap: "Slaking behaviour ratings"

dat_ft_slak <-
  tribble(~Code, ~Name, ~Description,
          'N', 'No slaking',  'Peds remain intact. Some bubbles may develop on their surfaces', 
          'P', 'Partial slaking', 'Peds have broken open or partially collapsed, mostly into smaller peds',
          'C', 'Complete slaking', 'Peds have collapsed into a pile of separated grains, little to no ped structure remains visible') 

tbl_ft_slak <- gt(dat_ft_slak) |>
  tab_options(
    column_labels.font.weight = 'bold', 
    heading.title.font.weight = 'bold',
    table.align = 'center',
    table.width = '85%'
  ) |>
  tab_style(style = list(cell_text(color  = 'red', 
                                   weight = 'bold',
                                   align  = 'center')),
            locations = cells_body(columns = 1)) |>
  cols_width(Code ~pct(10), Name ~ pct(20))
  
tbl_ft_slak
```

```{r}
#| label: tbl-ft-disp
#| tbl-cap: "Dispersion behaviour ratings"

dat_ft_disp <-
  tribble(~Code, ~Name, ~Description,
          'N', 'No dispersal',  'Peds remain intact and water remains clear', 
          'S', 'Slight dispersion', 'Peds remain largely intact but a faint milky halo of suspended clay particles can be seen around them',
          'M', 'Moderate dispersion', 'Peds partly collapse and a milky halo is visible around the sample',
          'C', 'Complete dispersion', 'Peds have collapsed into a pile of separate grains, and are surrounded by an extensive and dense halo.') 

tbl_ft_disp <- gt(dat_ft_disp) |>
  tab_options(
    column_labels.font.weight = 'bold', 
    heading.title.font.weight = 'bold',
    table.align = 'center',
    table.width = '85%'
  ) |>
  tab_style(style = list(cell_text(color  = 'red',
                                   weight = 'bold',
                                   align  = 'center')),
            locations = cells_body(columns = 1)) |>
  cols_width(Code ~pct(10), Name ~ pct(20))
  
tbl_ft_disp
```