Restart on boot

[Sylvesta]

Hi,

I upgraded from v2.2.4 to v2.3.6. The upload completes but when going through the boot sequence I get a restart:

Connecting to Wi-Fi...........
Connected with IP: 192.168.0.109

Firebase Client v2.3.6

[DEBUG] Initializing...
[DEBUG] Failed, Firebase authentication token is not ready.
Token info: type = id token, status = on request
Token info: type = id token, status = ready
[DEBUG] Checking databasse config and authentication...
[DEBUG] Setup stream...
[DEBUG] Stream setup completed
[DEBUG] Setup the database rules query index...
Guru Meditation Error: Core  1 panic'ed (Unhandled debug exception)
Debug exception reason: Stack canary watchpoint triggered (firesense_run_t) 
Core 1 register dump:
PC      : 0x40001615  PS      : 0x00060336  A0      : 0x800e1800  A1      : 0x3ffd5640  
A2      : 0x3ffcfd68  A3      : 0x3ffcedd2  A4      : 0xffffc347  A5      : 0x0000ff00  
A6      : 0x00ff0000  A7      : 0xff000000  A8      : 0x00000000  A9      : 0x00000000  
A10     : 0x3ffd3a20  A11     : 0x000000ff  A12     : 0x00000009  A13     : 0x3ffcfd70  
A14     : 0x00ff0000  A15     : 0x00000000  SAR     : 0x0000000a  EXCCAUSE: 0x00000001  
EXCVADDR: 0x00000000  LBEG    : 0x40001699  LEND    : 0x400016aa  LCOUNT  : 0xffffffa5  

ELF file SHA256: 0000000000000000

Backtrace: 0x40001615:0x3ffd5640 0x400e17fd:0x3ffd5650 0x400e1dc2:0x3ffd56c0 0x400e1f2e:0x3ffd5710 0x400e2125:0x3ffd5770 0x400e9237:0x3ffd57b0 0x400e7282:0x3ffd57e0 0x400e74b1:0x3ffd58c0 0x400d43dd:0x3ffd58e0 0x400d4504:0x3ffd5920 0x400d9f85:0x3ffd5950 0x400da845:0x3ffd5970 0x4008a37a:0x3ffd5990

Rebooting...
ets Jul 29 2019 12:21:46

rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0018,len:4
load:0x3fff001c,len:1216
ho 0 tail 12 room 4
load:0x40078000,len:10944
load:0x40080400,len:6388
entry 0x400806b4

Any ideas?

[mobizt]

v2.3.6 is not published yet.
Please go back to v2.3.5.

[mobizt]

I'll check and if possible, post your code here.

[mobizt]

The library v2.3.6 is available.

In your sketch, you are using ADC2 (gpio 25 and 26) which can't be used when WiFi is enable.
This blog provides the details https://randomnerdtutorials.com/esp32-pinout-reference-gpios/

I test your sketch by remove all third party sensors libraries and it is ok.

[Sylvesta]

Hmm good find, I totally missed that even though I read it before.

I'll give .6 a go.

For interest sake, what is different in 2.2.4 vs 2.3.6 as 2.2.4 worked fine?

Thank you again!

[mobizt]

You should see the release note.

[Sylvesta]

Haha I will definitely take a look, thought maybe it was something simple ;)