Blinky basic application not loading in uboot for the same load address as hello world for iMX8MP

[Esaii0114]

i have configured unused gpio in A53 dts like below
aliases {
led0 = &myled0;
};

leds {
compatible = "gpio-leds";
myled0: led_0 {
gpios = <&gpio4 20 GPIO_ACTIVE_LOW>;
};
};

During compilation time no issue but while loading in uboot it is hanging .I have used below commands for loading in uboot.
fatload mmc 0:1 0x40000000 zephyr.bin
dcache off; icache flush
go 0x40000000

the same commands works for fine for other applications but for blinky appliaction its hanging like this
U-Boot 2023.04-00001-gb88d03b44c1-dirty (Jan 07 2025 - 11:05:26 +0530)

CPU: i.MX8MP[8] rev1.1 1600 MHz (running at 1200 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 50C
Reset cause: POR
Model: iW-RainboW-G40M-i.MX8MP-OSM
Board: iWave iW-RainboW-G40M OSM
DRAM: 2 GiB
optee optee: OP-TEE api uid mismatch
Core: 257 devices, 35 uclasses, devicetree: separate
MMC: FSL_SDHC: 1, FSL_SDHC: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
SEC0: RNG instantiated
Board Info:
BSP Version : iW-PRGLZ-SC-01-R2.0-REL0.1-Linux6.6.3 Debian 12
SOM Version : iW-PRGLZ-AP-01-R2.0
CPU Unique ID : 0x0A0878007A3A417A
Carrier Board Version : iW-PRGJJ-AP-01-R1.0

switch to partitions #0, OK
mmc0(part 0) is current device
flash target is MMC:0
Net: eth0: ethernet@30be0000 [PRIME], eth1: ethernet@30bf0000
Fastboot: Normal
Normal Boot
Hit any key to stop autoboot: 0
iWave-G40M>
iWave-G40M>
iWave-G40M>
iWave-G40M> ums 0 mmc 0
UMS: LUN 0, dev mmc 0, hwpart 0, sector 0x0, count 0x1d5a000
CTRL+C - Operation aborted
iWave-G40M> fatload mmc 0:1 0x40000000 zephyr.bin
93984 bytes read in 3 ms (29.9 MiB/s)
iWave-G40M> dcache off; icache flush
iWave-G40M> go 0x40000000

Starting application at 0x40000000 ...

This is my bdinfo
iWave-G40M> bdinfo
boot_params = 0x0000000000000000
DRAM bank = 0x0000000000000000
-> start = 0x0000000040000000
-> size = 0x0000000080000000
flashstart = 0x0000000000000000
flashsize = 0x0000000000000000
flashoffset = 0x0000000000000000
baudrate = 115200 bps
relocaddr = 0x00000000bdea8000
reloc off = 0x000000007dca8000
Build = 64-bit
current eth = ethernet@30be0000
ethaddr = 00:01:02:03:04:05
IP addr =
fdt_blob = 0x00000000bbe998c0
new_fdt = 0x00000000bbe998c0
fdt_size = 0x000000000000e4c0
Video = lcd-controller@32e80000 inactive
Video = lcd-controller@32e90000 inactive
lmb_dump_all:
memory.cnt = 0x1
memory[0] [0x40000000-0xbfffffff], 0x80000000 bytes flags: 0
reserved.cnt = 0x4
reserved[0] [0x900000-0x96ffff], 0x00070000 bytes flags: 4
reserved[1] [0xbae8f000-0xbfffffff], 0x05171000 bytes flags: 0
reserved[2] [0xbbe95290-0xbfffffff], 0x0416ad70 bytes flags: 0
reserved[3] [0x100000000-0x10fffffff], 0x10000000 bytes flags: 4
devicetree = separate
arch_number = 0x0000000000000000
TLB addr = 0x00000000bfff0000
irq_sp = 0x00000000bbe998b0
sp start = 0x00000000bbe998b0
Early malloc usage: f200 / 10000